0% found this document useful (0 votes)
94 views63 pages

Enuth110 BTC

Uploaded by

Orosz János
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
94 views63 pages

Enuth110 BTC

Uploaded by

Orosz János
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 63

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. There is no guarantee that interference
will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents here and
specially disclaims any implied warranties of merchantability or fitness for any purpose. Further
the vendor reserves the right to revise this publication and to make changes to the contents here
without obligation to notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first obtaining the
vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we will not be
responsible for any mistakes found in this user’s manual. All the brand and product names are
trademarks of their respective companies.

Dichiarazione di conformità sintetica Short Declaration of conformity


Ai sensi dell’art. 2 comma 3 del D.M. 275 del We declare this product is complying with the
30/10/2002 laws in force and meeting all the essential
Si dichiara che questo prodotto è conforme requirements as specified by the directives
alle normative vigenti e soddisfa i requisiti 2004/108/CE, 2006/95/CE and 1999/05/CE
essenziali richiesti dalle direttive whenever these laws may be applied
2004/108/CE, 2006/95/CE e 1999/05/CE
quando ad esso applicabili
Table Of Contents
FCC Information and Copyright������������������������������������������������������������������������������� 1
Chapter 1: Introduction������������������������������������������������������������������������������������������� 3
1.1 Before You Start������������������������������������������������������������������������������������������������������������������ 3
1.2 Package Checklist���������������������������������������������������������������������������������������������������������������� 3
1.3 Specifications���������������������������������������������������������������������������������������������������������������������� 4
1.4 Rear Panel Connectors�������������������������������������������������������������������������������������������������������� 5
1.5 Motherboard Layout ���������������������������������������������������������������������������������������������������������� 6
Chapter 2: Hardware Installation����������������������������������������������������������������������������� 7
2.1 Install Central Processing Unit (CPU)���������������������������������������������������������������������������������� 7
2.2 Install a Heatsink����������������������������������������������������������������������������������������������������������������� 9
2.3 Connect Cooling Fans������������������������������������������������������������������������������������������������������� 10
2.4 Install System Memory����������������������������������������������������������������������������������������������������� 10
2.5 Expansion Slots����������������������������������������������������������������������������������������������������������������� 12
2.6 Jumper & Switch Setting��������������������������������������������������������������������������������������������������� 13
2.7 Headers & Connectors������������������������������������������������������������������������������������������������������ 14
Chapter 3: UEFI BIOS & Software��������������������������������������������������������������������������� 18
3.1 UEFI BIOS Setup���������������������������������������������������������������������������������������������������������������� 18
3.2 BIOS Update���������������������������������������������������������������������������������������������������������������������� 18
3.3 Software���������������������������������������������������������������������������������������������������������������������������� 22
Chapter 4: Useful Help������������������������������������������������������������������������������������������ 25
4.1 Driver Installation������������������������������������������������������������������������������������������������������������� 25
4.2 AMI BIOS Beep Code�������������������������������������������������������������������������������������������������������� 26
4.3 AMI BIOS post code���������������������������������������������������������������������������������������������������������� 26
4.4 Troubleshooting���������������������������������������������������������������������������������������������������������������� 28
APPENDIX I: Specifications in Other Languages����������������������������������������������������� 29
Arabic�������������������������������������������������������������������������������������������������������������������������������������� 29
German����������������������������������������������������������������������������������������������������������������������������������� 30
Russian������������������������������������������������������������������������������������������������������������������������������������ 31
Spanish����������������������������������������������������������������������������������������������������������������������������������� 32
Thai����������������������������������������������������������������������������������������������������������������������������������������� 33

2 | Table Of Contents
TH110-BTC

Chapter 1: Introduction

1.1 Before You Start


Thank you for choosing our product. Before you start installing the motherboard, please make
sure you follow the instructions below:
• Prepare a dry and stable working environment with sufficient lighting.
• Always disconnect the computer from power outlet before operation.
• Before you take the motherboard out from anti-static bag, ground yourself properly
by touching any safely grounded appliance, or use grounded wrist strap to remove the
static charge.
• Avoid touching the components on motherboard or the rear side of the board unless
necessary. Hold the board on the edge, do not try to bend or flex the board.
• Do not leave any unfastened small parts inside the case after installation. Loose parts
will cause short circuits which may damage the equipment.
• Keep the computer from dangerous area, such as heat source, humid air and water.
• The operating temperatures of the computer should be 0 to 45 degrees Celsius.
• To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit

1.2 Package Checklist


• Serial ATA Cable x2
• Rear I/O Panel for ATX Case x1
• User’s Manual x1
• Fully Setup Driver DVD x1
Note
» The package contents may be different due to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or sales
representative.

Chapter 1: Introduction | 3
1.3 Specifications
Specifications
Socket 1151 for Intel® Core i7 / i5 / i3 / Pentium / Celeron processor
CPU Support Maximum CPU TDP (Thermal Design Power): 95Watt
* Please refer to www.biostar.com.tw for CPU support list.
Chipset INTEL® H110
Supports Dual Channel DDR4 1866/2133/2400
2x DDR4 DIMM Memory Slot, Max. Supports up to 32 GB Memory
Memory Each DIMM supports non-ECC 4/8/16GB DDR4 module
* DDR4-2400 for 7th Generation Intel® Core™ Processor Family.
* Please refer to www.biostar.com.tw for Memory support list.
Storage 4x SATA III Connector (6Gb/s)
RTL8111H
LAN
10/ 100/ 1000 Mb/s auto negotiation, Half / Full duplex capability
ALC887
Audio Codec
7.1 Channels, High Definition Audio
4x USB 3.0 port (2 on rear I/Os and 2 via internal header)
USB
6x USB 2.0 port (2 on rear I/Os and 4 via internal header)
5x PCIe 2.0 x1 Slot (for Bitcoin mining, please change the speed to PCI-E 1.0 in BIOS setting)
Expansion Slots
1x PCIe 3.0 x16 Slot
1x PS/2 Mouse
1x PS/2 Keyboard
1x DVI-D Port
1x LAN port
Rear I/Os
2x USB Port (only 5V power, no USB signals)
2x USB 2.0 Port
2x USB 3.0 Port
3x Audio Jack
4x SATA III Connector (6Gb/s)
2x USB 2.0 Header (each header supports 2 USB 2.0 ports)
1x USB 3.0 Header (each header supports 2 USB 3.0 ports)
1x 8-Pin Power Connector
1x 24-Pin Power Connector
2x 4-Pin Power Connector (for Bitcoin mining, 4pin power connector Must be Installed)
Internal I/Os 1x 15-Pin SATA Power Connector (for USB power enhancement)
1x CPU Fan Connector
2x System Fan Connector
1x Front Panel Header
1x Front Audio Header
1x Clear CMOS Header
1x COM Port Header
Form Factor ATX Form Factor, 295mm x 210mm
Windows 7 (32/64bit) / 8.1(64bit) /10(64bit)
OS Support * Windows 7 (32/64bit) / 8.1(64bit) for 6th Generation Intel® Core™ Processor Family only.
* Biostar reserves the right to add or remove support for any OS with or without notice.

4 | Chapter 1: Introduction
TH110-BTC

1.4 Rear Panel Connectors

Note
» DVI-D port only works with an Intel® integrated Graphics Processor.
»»  Maximum resolution
DVI-D: 1920 x 1200 @60Hz
»»  When using the front HD audio jack and plug in the headset, the rear sound will be automatically
Disabled.
»»  To configure 7.1-channel audio, you have to use a chassis with HD front panel audio module and
enable the multi-channel audio feature through O.S. Audio Utility.
»»  The USB 5V port only provides 5V power for your accessories. (e.g. headphones and USB charger
devices.)

The 2/ 4/ 5.1/ 7.1-channel configuration


Audio Port 2-channel 4-channel 5.1 channel 7.1 channel
Blue (Rear Panel) Line In Line In Line In Side Speaker Out
Green (Rear Panel) Line Out Front Speaker Out Front Speaker Out Front Speaker Out
Pink (Rear Panel) Mic In Mic In Center/Subwoofer Out Center/Subwoofer Out
Green (Front Panel) Headphone Rear Speaker Out Rear Speaker Out Rear Speaker Out

Chapter 1: Introduction | 5
1.5 Motherboard Layout

Note
» represents the 1st pin.

6 | Chapter 1: Introduction
TH110-BTC

Chapter 2: Hardware Installation

2.1 Install Central Processing Unit (CPU)


Step 1: Locate the CPU socket on the motherboard

Note
» Remove pin cap before installation, and make good preservation for future use. When the CPU is
removed, cover the pin cap on the empty socket to ensure pin legs won’t be damaged.
» The motherboard might equip with two different types of pin cap. Please refer below instruction to
remove the pin cap.
Step 2: Pull the socket locking lever out from the socket and then raise the lever up.

Step 3: Remove the Pin Cap.

Chapter 2: Hardware Installation | 7


Step 4: Hold processor with your thumb and index fingers, oriented as shown. Align the
notches with the socket. Lower the processor straight down without tilting or sliding the
processor in the socket.

Step 5: Hold the CPU down firmly, and then lower the lever to locked position to complete the
installation.

Note
» Ensure that you install the correct CPU designed for LGA1151 socket.
» The CPU fits only in one correct orientation. Do not force the CPU into the socket to prevent
damaging the CPU.

8 | Chapter 2: Hardware Installation


TH110-BTC

2.2 Install a Heatsink


Step 1: Place the CPU fan assembly on top of the installed CPU and make sure that the four
fasteners match the motherboard holes. Orient the assembly and make the fan cable is closest
to the CPU fan connector.

Step 2: Press down two fasteners at one time in a diagonal sequence to secure the CPU fan
assembly in place. As each fastener locks into position a click should be heard.

Note
» Apply the thermal interface material on the CPU before heatsink installation, if necessary.
» Do not forget to connect the CPU fan connector.
» For proper installation, please kindly refer to the installation manual of your CPU heatsink.

Chapter 2: Hardware Installation | 9


2.3 Connect Cooling Fans
These fan headers support cooling-fans built in the computer. The fan cable and connector
may be different according to the fan manufacturer.
CPU_FAN1: CPU Fan Header

Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate sense
4 Smart Fan Control (By Fan)

SYS_FAN1/ SYS_FAN2: System Fan Header

Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate sense
4 Smart Fan Control (By Fan)

Note
» CPU_FAN1, SYS_FAN1 & SYS_FAN2 support 4-pin and 3-pin head connectors. When connecting
with wires onto connectors, please note that the red wire is the positive and should be connected to
pin#2, and the black wire is Ground and should be connected to pin#1(GND).

2.4 Install System Memory


DDR4 Modules

10 | Chapter 2: Hardware Installation


TH110-BTC

Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot
such that the notch on the DIMM matches the break on the slot.

Step 2: Insert the DIMM vertically and firmly into the slot until the retaining clips snap back in
place and the DIMM is properly seated.

Note
» If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.

Memory Capacity
DIMM Socket Location DDR4 Module Total Memory Size
DIMMA1 4GB/8GB/16GB
Max is 32GB.
DIMMB1 4GB/8GB/16GB

Dual Channel Memory Installation


Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status DIMMA1 DIMMB1
Disabled O X
Disabled X O
Enabled O O
(O means memory installed, X means memory not installed.)
Note
» When installing more than one memory module, we recommend to use the same brand and
capacity memory on this motherboard.

Chapter 2: Hardware Installation | 11


2.5 Expansion Slots
PEX16_1: PCI-Express Gen3 x16 Slot
• PCI-Express 3.0 compliant.
• Theoretical maximum bandwidth using two slots simultaneously is 16GB/s for each slot,
a total of 32GB/s.
PEX1_1/ PEX1_2/ PEX1_3/ PEX1_4/ PEX1_5: PCI-Express Gen2 x1 Slots
• PCI-Express 2.0 compliant.
• Data transfer bandwidth up to 0.5GB/s per direction; 1GB/s in total

Install an Expansion Card


You can install your expansion card by following steps:
• Read the related expansion card’s instruction document before install the expansion
card into the computer.
• Remove your computer’s chassis cover, screws and slot bracket from the computer.
• Place a card in the expansion slot and press down on the card until it is completely
seated in the slot.
• Secure the card’s metal bracket to the chassis back panel with a screw.
• Replace your computer’s chassis cover.
• Power on the computer, if necessary, change BIOS settings for the expansion card.
• Install related driver for the expansion card.

12 | Chapter 2: Hardware Installation


TH110-BTC

2.6 Jumper & Switch Setting


The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the
jumper is “close”, if not, that means the jumper is “open”.
Pin opened Pin closed Pin 1-2 closed

JCMOS1: Clear CMOS Jumper


The jumper allows users to restore the BIOS safe setting and the CMOS data. Please carefully
follow the procedures to avoid damaging the motherboard.

Pin 1-2 Open: Normal Operation (Default)

Pin 1-2 Close: Clear CMOS data

Clear CMOS Procedures:


1. Remove AC power line.
2. Set the jumper to “Pin 1-2 close”, you can use a metal object like a screwdriver to touch
the two pins.
3. Wait for five seconds.
4. After clearing the CMOS values, be sure the jumper is “Pin 1-2 open”.
5. Power on the AC.
6. Load Optimal Defaults and save settings in CMOS.

Chapter 2: Hardware Installation | 13


2.7 Headers & Connectors
ATXPWR1: ATX Power Source Connector
For better compatibility, we recommend to use a standard ATX 24-pin power supply for this
connector. Make sure to find the correct orientation before plugging the connector.
Pin Assignment Pin Assignment
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

ATXPWR2: ATX Power Source Connector


The connector provides +12V to the CPU power circuit. If the CPU power plug is 4-pin, please
plug it into Pin 1-2-5-6 of ATXPWR2.

Pin Assignment
1 +12V
2 +12V
3 +12V
4 +12V
5 Ground
6 Ground
7 Ground
8 Ground

Note
» Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2 connectors
have been plugged-in.
» Insufficient power supplied to the system may result in instability or the peripherals not functioning
properly. Use of a PSU with a higher power output is recommended when configuring a system with
more power-consuming devices.

14 | Chapter 2: Hardware Installation


TH110-BTC

AUXPWR1/2: Auxiliary Power for Graphics


(for Bitcoin mining, 4pin power connector must be installed)
This connector is an auxiliary power connection for graphics cards. Exclusive power for the
graphics card provides better graphics performance.

Pin Assignment
1 +12V
2 Ground
3 Ground
4 +5V

SATA_POWER: SATA Power Source Connector


This SATA power connector enhances the power of rear USB ports.

Pin Assignment Pin Assignment


1 VCC3 9 VCC5
2 VCC3 10 Ground
3 VCC3 11 N/A
4 Ground 12 Ground
5 Ground 13 12V
6 Ground 14 12V
7 VCC5 15 12V
8 VCC5 --- ---

PANEL1: Front Panel Header


This 16-pin header includes Power-on, Reset, HDD LED, Power LED, and speaker connection.

Pin Assignment Function Pin Assignment Function


1 +5V 9 N/A
N/A
2 N/A Speaker 10 N/A
3 N/A Connector 11 N/A N/A
4 Speaker 12 Power LED (+)
Power
5 HDD LED (+) Hard drive 13 Power LED (+)
LED
6 HDD LED (-) LED 14 Power LED (-)
7 Ground Reset 15 Power button Power-on
8 Reset control button 16 Ground button

Chapter 2: Hardware Installation | 15


SATA3_1/3_2/3_3/3_4: Serial ATA Connectors
These connectors connect to SATA hard disk drives via SATA cables.

Pin Assignment
1 Ground
2 TX+
3 TX-
4 Ground
5 RX-
6 RX+
7 Ground

JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel


This header allows user to add additional USB ports on the PC front panel, and also can be
connected with a wide range of external peripherals.
Pin Assignment Pin Assignment
1 VBUS0 11 D2+
2 SSRX1- 12 D2-
3 SSRX1+ 13 Ground
4 Ground 14 SSTX2+
5 SSTX1- 15 SSTX2-
6 SSTX1+ 16 Ground
7 Ground 17 SSRX2+
8 D1- 18 SSRX2-
9 D1+ 19 VBUS1
10 ID 20 Key

F_USB1/2: Header for USB 2.0 Ports at Front Panel


This header allows user to add additional USB ports on the PC front panel, and also can be
connected with a wide range of external peripherals.
Pin Assignment
1 +5V (fused)
2 +5V (fused)
3 USB-
4 USB-
5 USB+
6 USB+
7 Ground
8 Ground
9 Key
10 NC

16 | Chapter 2: Hardware Installation


TH110-BTC

F_AUDIO1: Front Panel Audio Header


This header allows user to connect the chassis-mount front panel audio I/O which supports HD
and AC’97 audio standards.
HD Audio AC’97
Pin Assignment Pin Assignment
1 Mic Left in 1 Mic In
2 Ground 2 Ground
3 Mic Right in 3 Mic Power
4 GPIO 4 Audio Power
5 Right line in 5 RT Line Out
6 Jack Sense 6 RT Line Out
7 Front Sense 7 Reserved
8 Key 8 Key
9 Left line in 9 LFT Line Out
10 Jack Sense 10 LFT Line Out

Note
» It is recommended that you connect a high-definition front panel audio module to this connector to
avail of the motherboard’s high definition audio capability.
» Please try to disable the “Front Panel Jack Detection” if you want to use an AC’97 front audio output
cable. The function can be found via O.S. Audio Utility.

COM1: Serial Port Header


The motherboard has a serial port header for connecting RS-232 Port.
Pin Assignment
1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send
8 Clear to send
9 Ring indicator
10 Key

Chapter 2: Hardware Installation | 17


Chapter 3: UEFI BIOS & Software

3.1 UEFI BIOS Setup


• The BIOS Setup program can be used to view and change the BIOS settings for the
computer. The BIOS Setup program is accessed by pressing the <DEL> key after the
Power-On Self-Test (POST) memory test begins and before the operating system boot
begins.
• For further information of setting up the UEFI BIOS, please refer to the UEFI BIOS Manual
on our website.

3.2 BIOS Update


The BIOS can be updated using either of the following utilities:
• BIOSTAR BIOS-FLASHER: Using this utility, the BIOS can be updated from a file on a hard
disk, a USB drive (a flash drive or a USB hard drive), or a CD-ROM.
• BIOSTAR BIOS Update Utility: It enables automated updating while in the Windows
environment. Using this utility, the BIOS can be updated from a file on a hard disk, a USB
drive (a flash drive or a USB hard drive), or a CD-ROM, or from the file location on the
Web.
BIOSTAR BIOS-FLASHER
Note
» This utility only allows storage device with FAT32/16 format and single partition.
» Shutting down or resetting the system while updating the BIOS will lead to system boot failure.
Updating BIOS with BIOSTAR BIOS-FLASHER
1. Go to the website to download the latest BIOS file for the motherboard.
2. Then, copy and save the BIOS file into a USB flash (pen) drive.(Only supported FAT/FAT32
format)
3. Insert the USB pen drive that contains the BIOS file to the USB port.
4. Power on or reset the computer and then press <F12> during the POST process.

5. After entering the POST screen, the BIOS-


FLASHER utility pops out. Choose <fs0> to search
for the BIOS file.

18 | Chapter 3: UEFI BIOS & Software


TH110-BTC

6. Select the proper BIOS file, and a message asking


if you are sure to flash the BIOS file. Click “Yes” to
start updating BIOS.

7. A dialog pops out after BIOS flash is completed,


asking you to restart the system. Press the <Y> key
to restart system.

8. While the system boots up and the full screen logo shows up, press <DEL> key to enter BIOS
setup.
After entering the BIOS setup, please go to the <Save & Exit>, using the <Restore Defaults>
function to load Optimized Defaults, and select <Save Changes and Reset> to restart the
computer. Then the BIOS Update is completed.
BIOS Update Utility (through the Internet)
1. Installing BIOS Update Utility from the DVD Driver.
2. Please make sure the system is connected to the internet before using this function.

3. Launch BIOS Update Utility and click the


“Online Update” button on the main screen.

4. An open dialog will show up to request your


agreement to start the BIOS update. Click “Yes”
to start the online update procedure.

Chapter 3: UEFI BIOS & Software | 19


5. If there is a new BIOS version, the utility will
ask you to download it. Click “Yes” to proceed.

6. After the download is completed, you will be


asked to program (update) the BIOS or not. Click
“Yes” to proceed.

7. After the updating process is finished, you


will be asked you to reboot the system. Click
“OK” to reboot.

8. While the system boots up and the full screen logo shows up, press <DEL> key to enter BIOS
setup.
After entering the BIOS setup, please go to the <Save & Exit>, using the <Restore Defaults>
function to load Optimized Defaults, and select <Save Changes> and <Reset> to restart the
computer. Then, the BIOS Update is completed.
BIOS Update Utility (through a BIOS file)
1. Installing BIOS Update Utility from the DVD Driver.
2. Download the proper BIOS from http://www.biostar.com.tw/

3. Launch BIOS Update Utility and click the “Update


BIOS” button on the main screen.

4. A warning message will show up to request your


agreement to start the BIOS update. Click “OK” to
start the update procedure.

20 | Chapter 3: UEFI BIOS & Software


TH110-BTC

5. Choose the location for your BIOS file in the


system. Please select the proper BIOS file, and
then click on “Open”. It will take several minutes,
please be patient.

6. After the BIOS Update process is finished, click


on “OK” to reboot the system.

7. While the system boots up and the full screen logo shows up, press <DEL> key to enter BIOS
setup.
After entering the BIOS setup, please go to the <Save & Exit>, using the <Restore Defaults>
function to load Optimized Defaults, and select <Save Changes and Reset> to restart the
computer. Then, the BIOS Update is completed.

Backup BIOS
Click the Backup BIOS button on the main screen
for the backup of BIOS, and select a proper
location for your backup BIOS file in the system,
and click “Save”.

Chapter 3: UEFI BIOS & Software | 21


3.3 Software
Installing Software
1. Insert the Setup DVD to the optical drive. The driver installation program would appear if
the Auto-run function has been enabled.
2. Select Software Installation, and then click on the respective software title.
3. Follow the on-screen instructions to complete the installation.
Launching Software
After the installation process is completed, you will see the software icon showing on the
desktop. Double-click the icon to launch it.
Note
» All the information and content about following software are subject to be changed without notice.
For better performance, the software is being continuously updated.
» The information and pictures described below are for your reference only. The actual information
and settings on board may be slightly different from this manual.

BIOScreen Utility
This utility allows you to personalize your boot logo easily. You can choose BMP as your boot
logo so as to customize your computer.

Please follow the step-by-step instructions below to update boot logo:


• Load Image: Choose the picture as the boot logo.
• Transform: Transform the picture for BIOS and preview the result.
• Update Bios: Write the picture to BIOS Memory to complete the update.

22 | Chapter 3: UEFI BIOS & Software


TH110-BTC

eHot-Line
eHot-Line is a convenient utility that helps you to contact with our Tech-Support system. This
utility will collect the system information which is useful for analyzing the problem you may
have encountered, and then send these information to our tech-support department to help
you fix the problem.

After filling up this information, click “Send” to send


the mail out. A warning dialog would appear asking
for your confirmation; click “Send” to confirm or “Do
Not Send” to cancel.

If you want to save this information to a .txt file,


click “Save As…” and then you will see a saving
dialog appears asking you to enter file name.

Chapter 3: UEFI BIOS & Software | 23


Enter the file name and then click “Save”. Your
system information will be saved to a .txt file.

Open the saved .txt file, you will see your system
information including motherboard/BIOS/CPU/
video/device/OS information. This information is
also concluded in the sent mail.

Note
» Before you use this utility, please set Outlook Express as your default e-mail client application
program.
» We will not share customer’s data with any other third parties, so please feel free to provide your
system information while using eHot-Line service.
» If you are not using Outlook Express as your default e-mail client application, you may need to
save the system information to a .txt file and send the file to our tech support with other e-mail
application. Go to the following website http://www.biostar.com.tw/app/en/about/contact.php for
getting our contact information.

24 | Chapter 3: UEFI BIOS & Software


TH110-BTC

Chapter 4: Useful Help

4.1 Driver Installation


After you installed your operating system, please insert the Fully Setup Driver DVD into your
optical drive and install the driver for better system performance.
You will see the following window after you insert the DVD

The setup guide will auto detect your motherboard and operating system.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will list the compatible
driver for your motherboard and operating system. Click on each device driver to launch the
installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide will list the software
available for your system, click on each software title to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver DVD. Click on the
Manual icon to browse for available manual.
Note
» If this window didn’t show up after you insert the Driver DVD, please use file browser to locate and
execute the file SETUP.EXE under your optical drive.
» You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat
Reader software from http://get.adobe.com/reader/

Chapter 4: Useful Help | 25


4.2 AMI BIOS Beep Code
Boot Block Beep Codes
Number of Beeps Description
Continuing Memory sizing error or Memory module not found

POST BIOS Beep Codes


Number of Beeps Description
1 Success booting.
8 Display memory error (system video adapter)

4.3 AMI BIOS post code


Code Description
10 PEI Core is started
11 Pre-memory CPU initialization is started
15 Pre-memory North Bridge initialization is started
19 Pre-memory South Bridge initialization is started
2B Memory initialization. Serial Presence Detect (SPD) data reading
2C Memory initialization. Memory presence detection
2D Memory initialization. Programming memory timing information
2E Memory initialization. Configuring memory
2F Memory initialization (other).
31 Memory Installed
32 CPU post-memory initialization is started
33 CPU post-memory initialization. Cache initialization
34 CPU post-memory initialization. Application Processor(s) (AP) initialization
35 CPU post-memory initialization. Boot Strap Processor (BSP) selection
36 CPU post-memory initialization. System Management Mode (SMM) initialization
37 Post-Memory North Bridge initialization is started
3B Post-Memory North Bridge initialization (North Bridge module specific)
4F DXE IPL is started
60 DXE Core is started
F0 Recovery condition triggered by firmware (Auto recovery)
F1 Recovery condition triggered by user (Forced recovery)
F2 Recovery process started
F3 Recovery firmware image is found
F4 Recovery firmware image is loaded
E0 S3 Resume is stared (S3 Resume PPI is called by the DXE IPL)
E1 S3 Boot Script execution
E2 Video repost
E3 OS S3 wake vector call
60 DXE Core is started
61 NVRAM initialization
62 Installation of the South Bridge Runtime Services
63 CPU DXE initialization is started
68 PCI host bridge initialization
69 North Bridge DXE initialization is started
6A North Bridge DXE SMM initialization is started

26 | Chapter 4: Useful Help


TH110-BTC

Code Description
70 South Bridge DXE initialization is started
71 South Bridge DXE SMM initialization is started
72 South Bridge devices initialization
78 South Bridge DXE Initialization (South Bridge module specific)
79 ACPI module initialization
90 Boot Device Selection (BDS) phase is started
91 Driver connecting is started
92 PCI Bus initialization is started
93 PCI Bus Hot Plug Controller Initialization
94 PCI Bus Enumeration
95 PCI Bus Request Resources
96 PCI Bus Assign Resources
97 Console Output devices connect
98 Console input devices connect
99 Super IO Initialization
9A USB initialization is started
9B USB Reset
9C USB Detect
9D USB Enable
A0 IDE initialization is started
A1 IDE Reset
A2 IDE Detect
A3 IDE Enable
A4 SCSI initialization is started
A5 SCSI Reset
A6 SCSI Detect
A7 SCSI Enable
A8 Setup Verifying Password
A9 Start of Setup
AB Setup Input Wait
AD Ready To Boot event
AE Legacy Boot event
AF Exit Boot Services event
B0 Runtime Set Virtual Address MAP Begin
B1 Runtime Set Virtual Address MAP End
B2 Legacy Option ROM Initialization
B3 System Reset
B4 USB hot plug
B5 PCI bus hot plug
B6 Clean-up of NVRAM
B7 Configuration Reset (reset of NVRAM settings)

Chapter 4: Useful Help | 27


4.4 Troubleshooting
Probable Solution
1. There is no power in the system. Power LED does 1. Make sure power cable is securely plugged in.
not shine; the fan of the power supply does not work 2. Replace cable.
2. Indicator light on keyboard does not shine. 3. Contact technical support.

System is inoperative. Keyboard lights are on, power Using even pressure on both ends of the DIMM,
indicator lights are lit, and hard drives are running. press down firmly until the module snaps into place.
1. Check cable running from disk to disk controller
board. Make sure both ends are securely plugged in;
System does not boot from a hard disk drive, but can check the drive type in the standard CMOS setup.
be booted from optical drive. 2. Backing up the hard drive is extremely important.
All hard disks are capable of breaking down at any
time.

System only boots from an optical drive. Hard disks 1. Back up data and applications files.
can be read, applications can be used, but system 2. Reformat the hard drive. Re-install applications
fails to boot from a hard disk. and data using backup disks.

Screen message shows “Invalid Configuration” or Review system’s equipment. Make sure correct
“CMOS Failure.” information is in setup.

1. Set master/slave jumpers correctly.


System cannot boot after user installs a second hard 2. Run SETUP program and select correct drive types.
drive. Call the drive manufacturers for compatibility with
other drives.

CPU Overheated
If the system shutdown automatically after power on system for seconds, that means the CPU
protection function has been activated.

When the CPU is over heated, the motherboard will shutdown automatically to avoid a
damage of the CPU, and the system may not power on again.

In this case, please double check:


1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.

Or you can:
1. Clear the CMOS data. (See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.

28 | Chapter 4: Useful Help


‫‪TH110-BTC‬‬

‫‪APPENDIX I: Specifications in Other Languages‬‬


‫‪Arabic‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫اﻟﻤﺄﺧﺬ ‪ 1151‬ﻟﻤﻌﺎﻟﺞ اﻳﻪ إم دى ‪Intel® Core i7 / i5 / i3 / Pentium / Celeron‬‬
‫اﻟﺤﺪ اﻷﻗﺼﻰ ﻟﻠﻄﺎﻗﺔ اﻟﺤﺮارﻳﺔ ﻓﻲ ﺗﺼﻤﻴﻢ اﻟﻤﻌﺎﻟﺞ ) ‪ 95 :( thermal design power – TDP‬واط‪.‬‬ ‫ﻗﺎﻋﺪة وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫* ﻳﺮﺟﻰ اﻟﺮﺟﻮع إﻟﻰ اﻟﻤﻮﻗﻊ ‪ www.biostar.com.tw‬ﻟﻘﺎﺋﻤﺔ دﻋﻢ اﻟﻤﻌﺎﻟﺞ ‪.CPU‬‬
‫‪INTEL® H110‬‬ ‫ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫ﺗﺪﻋﻢ ﻗﻨﺎة ﻣﺰدوﺟﺔ دي‪ .‬دي‪ .‬ار‪1866/2133/2400 DDR4 .‬‬
‫‪ 2x‬دي‪ .‬دي‪ .‬ار‪ DDR4 .‬ﻓﺘﺤﺎت اﻟﺬاآﺮة اﻟﻤﺰدوﺟﺔ ‪ ،DIMM‬ﺗﺘﺤﻤﻞ آﺤﺪ أﻗﺼﻰ ‪ 32‬ﺟﻴﺠﺎﺑﺎﻳﺖ ذاآﺮة‬
‫آﻞ ﻓﺘﺤﺔ ﻣﺰدوﺟﺔ ‪ DIMM‬ﺗﺘﺤﻤﻞ دون ‪16/8/4 ECC‬ﺟﻴﺠﺎﺑﺎﻳﺖ دي‪ .‬دي‪ .‬ار ‪DDR4‬‬ ‫اﻟﺬاآﺮة‬
‫* اﻟﻤﻌ������ﺎﻟﺞ ﻋﺎﺋﻠ�����ﺔ ™ ‪ Intel® Core‬اﻟﻤﻌ������ﺎﻟﺞ اﻟﺠﻴ������ﻞ ‪ 7‬إﻧﺘ������ﻞ ﻟﺸ������ﺮآﺔ ‪.DDR4-2400‬‬
‫* ﻳﺮﺟﻰ اﻟﺮﺟﻮع إﻟﻰ اﻟﻤﻮﻗﻊ ‪ www.biostar.com.tw‬ﻟﻘﺎﺋﻤﺔ دﻋﻢ اﻟﺬاآﺮة‪.‬‬
‫ﺻﻠﺔ ‪ 4x‬ﺳﺎﺗﺎ)‪SATA III(6Gb/s‬‬ ‫اﻟﺘﺨﺰﻳﻦ‬
‫‪RTL8111H‬‬
‫ﺷﺒﻜﺔ ﻣﺤﻠﻴﺔ ‪LAN‬‬
‫‪ 1000 / 100 / 10‬ﻣﻴﺠﺎﺑﺎﻳﺖ ‪ /‬اﻟﺜﺎﻧﻴﺔ ‪ ،‬ﺗﺤﺪﻳﺪ ﺗﻠﻘﺎﺋﻲ ‪ ،‬اﻟﻨﺼﻒ ‪ /‬اﻟﻘﺪرة اﻟﻘﺼﻮى اﻟﻤﺰدوﺟﺔ‬
‫‪ALC887‬‬
‫اﻟﺘﺮﻣﻴﺰ اﻟﺼﻮﺗﻲ‬
‫‪ 7.1‬ﻗﻨﻮات ﻋﺎﻟﻴﺔ اﻟﺪﻗﺔ‬

‫ﻣﻨﺎﻓﺬ ‪ x 4‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪ 2) 3.0 USB‬ﻓﻲ اﻟﻤﺪاﺧﻞ واﻟﻤﺨﺎرج اﻟﺨﻠﻔﻴﺔ و ‪ 2‬ﻣﻦ ﺧﻼل اﻟﻤﻮزع اﻟﺪاﺧﻠﻲ (‬
‫ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪USB‬‬
‫ﻣﻨﺎﻓﺬ ‪ x 6‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪ 2) 2.0 USB‬ﻓﻲ اﻟﻤﺪاﺧﻞ واﻟﻤﺨﺎرج اﻟﺨﻠﻔﻴﺔ و ‪ 4‬ﻣﻦ ﺧﻼل اﻟﻤﻮزع اﻟﺪاﺧﻠﻲ (‬

‫‪ x 5‬ﻓﺘﺤﺔ ﻣﻨﻔﺬ اﻟﻤﻠﺤﻘﺎت اﻹﺿﺎﻓﻴﺔ ‪ BIOS)1 x 2.0 PCIe‬إﻋﺪاد ﻓ�����ﻲ ‪ PCI-E 1.0‬ﺳ��ﺮﻋﺔ ﺗﻐﻴ�����������ﻴﺮ ‪،‬ﺑﻴﺘﻜ���������������ﻮﻳﻦ ﻟﻠﺘﻌ�������������ﺪﻳﻦ(‬
‫ﻓﺘﺤﺎت اﻟﺘﻮﺳﻊ‬
‫‪ x 1‬ﻓﺘﺤﺔ ﻣﻨﻔﺬ اﻟﻤﻠﺤﻘﺎت اﻹﺿﺎﻓﻴﺔ ‪16 x 3.0 PCIe‬‬
‫‪ PS/2 x 1‬ﻟﻮﺣﺔ اﻟﻤﻔﺎﺗﻴﺢ ﻟﻠﻜﻤﺒﻴﻮﺗﺮ‬
‫‪ PS/2 x 1‬اﻟﻔﺎرة‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 1‬واﺟﻬﺔ ﻣﺮﺋﻴﺔ رﻗﻤﻴﺔ ‪DVI-D‬‬
‫ﻓﺘﺤﺔ ﻟﺘﻮﺻﻴﻞ ﻋﺪد ‪ x 1‬اﻟﺸﺒﻜﺔ اﻟﻤﺤﻠﻴﺔ ‪LAN‬‬
‫اﻟﻤﺪاﺧﻞ واﻟﻤﺨﺎرج اﻟﺨﻠﻔﻴﺔ‬
‫‪ X2‬ﻣﻮﺻﻞ ‪) USB‬ﻓﻘﻂ ‪ 5V‬إﻣﺪادات اﻟﻄﺎﻗﺔ‪ ،‬وﻋﺪم وﺟﻮد إﺷﺎرة ‪(USB‬‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 2‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪2.0 USB‬‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 2‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪3.0 USB‬‬
‫ﻓﺘﺤﺔ ﺗﻮﺻﻴﻞ ﻋﺪد ‪ x 3‬ﺟﺎك ﻟﻠﺼﻮت‬
‫وﺻﻠﺔ ‪ 4x‬ﺳﺎﺗﺎ ‪SATA III‬‬
‫ﻣﻮزع ‪ x 2‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪ ) 2.0 USB‬آﻞ ﻣﻮزع ﻳﺘﺤﻤﻞ ﻓﺘﺤﺘﻴﻦ ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪(2.0 USB‬‬
‫ﻣﻮزع ‪ x 1‬ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪ ) 3.0 USB‬آﻞ ﻣﻮزع ﻳﺘﺤﻤﻞ ﻓﺘﺤﺘﻴﻦ ﻧﺎﻗﻞ ﻣﺘﺴﻠﺴﻞ ﻋﺎم ‪(3.0 USB‬‬
‫وﺻﻠﺔ ﻟﻠﻄﺎﻗﺔ ‪ 8 x 1‬دﺑﺎﺑﻴﺲ‬
‫وﺻﻠﺔ ﻟﻠﻄﺎﻗﺔ ‪ 24 x 1‬دﺑﻮس‬
‫وﺻﻠﺔ ﻟﻠﻄﺎﻗﺔ ‪ 4 x 2‬دﺑﻮس )ﻣﺜﺒﺘ����������ﺔ ﺗﻜ������ﻮن أن ﻳﺠ����� ‪ 4PIN‬اﻟﻄﺎﻗ����ﺔ ﻣﻮﺻ��ﻞ ‪،‬ﺑﻴﺘﻜ���������������ﻮﻳﻦ ﻟﻠﺘﻌ�������������ﺪﻳﻦ(‬
‫وﺻﻠﺔ ﻟﻠﻄﺎﻗﺔ ‪ 15 SATA x 1‬دﺑﻮس )ﻗ���ﻮة ﺗﻌ��������ﺰﻳﺰ ‪USB‬ل(‬ ‫اﻟﻤﺪاﺧﻞ واﻟﻤﺨﺎرج اﻟﺪاﺧﻠﻴﺔ‬
‫وﺻﻠﺔ ‪ x 1‬ﻣﺮوﺣﺔ ﺗﺒﺮﻳﺪ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫وﺻﻠﺔ ‪ x 2‬ﻣﺮاوح ﺗﺒﺮﻳﺪ اﻟﻤﻨﻈﻮﻣﺔ‬
‫ﻣﻮزع ‪ x 1‬اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻣﻮزع ‪ x 1‬اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬
‫ﻣﻮزع ‪ x 1‬ﺳﻴﻤﻮس ﻣﺒﺎﺷﺮ‬
‫ﻣﻮزع ‪ x 1‬ﻓﺘﺤﺔ ﺗﺴﻠﺴﻠﻴﺔ‬
‫ﻋﺎﻣﻞ ﺷﻜﻞ ﻣﺪد اﻟﺘﻜﻨﻮﻟﻮﺟﻴﺎ اﻟﻤﺘﻘﺪﻣﺔ ‪295 ، ATX‬ﻣﻢ ‪ 210 x‬ﻣﻢ‬ ‫ﻋﺎﻣﻞ اﻟﺸﻜﻞ‬
‫وﻳﻨﺪوز )‪ 7 (32/64bit‬وﻳﻨﺪوز)‪ /8.1(64bit‬وﻳﻨﺪوز)‪10(64bit‬‬
‫* وﻳﻨ������ﺪوز ‪ 8.1(64bit) / (32/64bit) 7‬ل ‪ 6TH‬اﻟﻤﻌ������ﺎﻟﺞ اﻟﺠﻴ������ﻞ ™‪ Intel® Core‬ﻋﺎﺋﻠﺔ اﻟﻤﻌﺎﻟﺞ ﻓﻘﻂ‪.‬‬ ‫أﻧﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ اﻟﻤﺪﻋﻮﻣﺔ‬
‫* ﺑﻴﻮﺳﺘﺎر ‪ BIOSTAR‬ﺗﺤﺘﻔﻆ ﺑﺤﻖ إﺿﺎﻓﺔ أو أزﻟﺔ اﻟﺪﻋﻢ ﻷي ﻧﻈﺎم ﺗﺸﻐﻴﻞ ﻣﻊ أو ﺑﺪون أﻧﻈﺎر‪.‬‬

‫‪APPENDIX I: Specifications in Other Languages | 29‬‬


German
Spezifikationen

Anschluss-1151 für Intel® Core i7 / i5 / i3 / Pentium / Celeron Prozessor


CPU-Unterstützung Maximale CPU TDP (Thermal Design Power): 95 Watt
* Bitte konsultieren Sie www.biostar.com.tw für CPU-Unterstützungsliste
Chipset INTEL® H110
Unterstützt zweikanaliges DDR4 1866/2133/2400
2x DDR4 DIMM-SpeicherSlot, Max. Uterstützung bis zu 32 GB-Speicher
Festplattenspeicher Jedes DIMM unterstützt nicht-ECC 4/8/16 GB DDR4-Module
* DDR4-2400 für die Intel® Core ™ Prozessorfamilie der 7. Generation.
* Bitte konsultieren Sie www.biostar.com.tw für für Speicherunterstützung Liste.
Arbeitsspeicher 4x SATA III-Verbindung
RTL8111H
LAN
10/ 100/ 1000 Mb Auto-Negotiation, Halb- / Voll-Duplex-fähig
ALC887
Audio-Codec
7.1 Kanäle, HD-Audio
4x USB 3.0-Port (2 hintere I/Os und 2 via interne Header)
USB
6x USB 2.0-Port (2 hintere I/Os und 4 via interne Header)
5x PCIe 2.0 x1-Slot (Für Bitcoin Mining, ändern Sie die Geschwindigkeit auf PCI-E 1.0 in BIOS-
Erweiterungsanschlüsse Einstellung)
1x PCIe 3.0 x16-Slot
1x PS/2-Maus
1x PS/2-Keyboard
1x DVI-D-Port
1x LAN-Port
Hintere I/Os
2x USB-Port (Nur 5V Leistung, keine USB-Signale)
2x USB 2.0-Port
2x USB 3.0-Port
3x Audio Jack
4x SATA III-Verbindung
2x USB 2.0-Header (jeder Header unterstützt 2 USB 2.0-Ports)
1x USB 3.0-Header (jeder Header unterstützt 2 USB 3.0-Ports)
1x 8-Pin-Stromverbindung
1x 24-Pin-Stromverbindung
2x 4-Pin-Stromverbindung (Für Bitcoin Mining, 4pin Stromanschluss Muss installiert sein)
Interne I/Os 1x 15-poliger SATA-Stromanschluss (Für USB-Leistungserhöhung)
1x CPU-Ventilatorverbindung
2x System-Ventilatorverbindung
1x Header für Frontpanel
1x Header für Frontaudio
1x Header für klares CMOS
1x Header für Seriellen Anschluss
Formfaktor ATX Formfaktor, 295 mm x 210mm
Windows 7 (32/64bit)/ 8.1(64bit) /10(64bit)
OS-Unterstützung * Windows 7 (32/64 Bit) / 8.1 (64 Bit) für die Intel® Core ™ Prozessorfamilie der 6. Generation.
* Biostar reserves the right to add or remove support for any OS with or without notice.

30 | APPENDIX I: Specifications in Other Languages


TH110-BTC

Russian
Спецификации
Поддержка Сокет 1151 для процессоров Intel® Core i7 / i5 / i3 / Pentium / Celeron
центрального Максимальный термопакет центрального процессора (TDP): 95 ватт
процессора * Перечень поддержки центрального процессора смотрите на www.biostar.com.tw.
Набор микросхем INTEL® H110
Поддерживает двухканальный DDR4 1866/2133/2400
2 гнезда платы памяти DDR4 DIMM, максимальная память до 32 Гб
Память Каждый модуль DIMM поддерживает модуль не-ECC 4/8/16 Гб DDR4
* DDR4-2400 для 7-го поколения Intel® Core ™ семейства процессоров.
* Перечень поддержки памяти смотрите на www.biostar.com.tw.
Накопитель Соединитель 4x SATA III
RTL8111H
Локальная сеть
Автосогласование 10/ 100/ 1000 Мб/с, работает в полно/полудуплексном режиме
ALC887
Аудиокодек
Каналы 7.1, высококачественное аудио
4 порта USB 3.0 (2 сзади ввода-вывода и 2 через внутренние контакты)
USB
6 порта USB 2.0 (2 сзади ввода-вывода и 4 через внутренние контакты)
5x PCIe 2.0 x1 гнездо (Для добычи Bitcoin, изменить скорость PCI-E 1.0 в настройки BIOS)
Гнезда расшир.
1x PCIe 3.0 x16 гнездо
1 мышь PS/2
1 клавиатура PS/2
1 порт DVI-D
Задняя плата ввода- 1 порт локальной сети
вывода 2 порта USB (только 5В питания, нет USB сигналов)
2 порта USB 2.0
2 порта USB 3.0
3 гнезд для подключения наушников
Соединитель 4x SATA III
2 контакта USB 2.0 (каждый контакт поддерживает 2 порта USB 2.0)
1 контакт USB 3.0 (каждый контакт поддерживает 2 порта USB 3.0)
1 8-выводный разъем питания
1 24-выводный разъем питания
2 4-выводный разъем питания (для добычи Bitcoin, 4pin разъем питания Должен быть установлен)
Внутр. Плата ввода-
1 разъем SATA питания 15-контактный (для повышения мощности USB)
вывода
1 разъем вентилятора ЦП
2 разъема вентилятора системы
1 контакт передней панели
1 контакт передней аудиопанели
1 контакт микросхемы Clear CMOS
1 контакт последовательного порта
Конструктив Форм-фактор ATX, 295мм x 210мм
Windows 7 (32/64bit)/ 8.1(64bit) /10(64bit)
* Windows 7 (32/64 бит) / 8,1 (64 бит) только для 6-го поколения Intel® Core ™ семейства
Поддержка ОС процессоров.
* Biostar оставляет за собой право добавлять или удалять поддержку любой ОС, с уведомлением
или без.

APPENDIX I: Specifications in Other Languages | 31


Spanish
Especificaciones

Ranura 1151 para procesador Intel® Core i7 / i5 / i3 / Pentium / Celeron


Compatibilidad con el
Alimentación de Proyección Térmica (TDP – Thermal Design Power): 95Watt
procesador
*Por favor consultar con www.biostar.com.tw para la lista de compatibilidad con el procesador.
Tipo de Placa INTEL® H110
Soporta DDR4 1866/2133/2400 Doble Canal
2x DDR4 DIMM Ranura de memoria Soporta hasta 32 GB Memoria
Memoria Cada DIMM soporta un modulo non-ECC 4/8/16 GB DDR4
* DDR4-2400 para la familia de procesadores Intel® Core ™ de 7ª generación.
* Por favor consultar con www.biostar.com.tw para la lista de compatibilidad con el memoria.
Almacenamiento de
Conector 4x SATA III
información
RTL8111H
LAN
10/ 100/ 1000 Mb/s auto negociación, capacidad dúplex Mitad/Completo
ALC887
Códec Audio
Canales Audio de Alta Definición 7.1
Ranura 4x USB 3.0 (2 en las entrada/salidas posteriores y 2 por los distribuidores internos)
USB
Ranura 6x USB 2.0 (2 en las entrada/salidas posteriores y 4 por los distribuidores internos)
Ranura 5x PCIe 2.0 x1 (Para la minería Bitcoin, cambie la velocidad a PCI-E 1.0 en la configuración del
Ranuras de Extinción BIOS)
Ranura 1x PCIe 3.0 x16
Ratón 1x PS/2
Teclado 1x PS/2
Ranura 1x DVI-D
Ranura 1x LAN
Panel trasero de E/S
Ranura 2x USB (Sólo 5V de potencia, Sin señales USB)
Ranura 2x USB 2.0
Ranura 2x USB 3.0
Socket audio 3x
Conector 4x SATA III
Distribuidor 2x USB 2.0 (cada distribuidor soporta 2 ranuras USB 2.0)
Distribuidor 1x USB 3.0 (cada distribuidor soporta 2 ranuras USB 3.0)
Conector con 8 patillas x1
Conector con 24 patillas x1
Conector con 4 patillas x2 (Para la minería de Bitcoin, se debe instalar un conector de alimentación de 4
pines)
Conectores en placa
Conector de alimentación SATA de 15 pines x1 (Para el aumento de potencia USB)
Conector Ventilador procesador x1
Conector Ventilador Sistema x2
Distribuidor Panel Frontal x1
Distribuidor Audio Frontal x1
Distribuidor CMOS Directo x1
Distribuidor Ranura Serie x1
Factor de Forma Factor de Forma ATX, 295mm x 210mm
Windows 7 (32/64bit)/ 8.1(64bit) /10(64bit)
* Windows 7 (32/64 bits) / 8.1 (64 bits) sólo para la familia de procesadores Intel® Core ™ de 6ª
Soporte OS
generación.
* Biostar reserva su derecho de añadir o retirar el soporte para cada OS con o sin notificación.

32 | APPENDIX I: Specifications in Other Languages


TH110-BTC

Thai
คุณสมบัติ

ซ็อกเก็ต 1151 สำ�หรับโปรเซสเซอร์ Intel Core i7 / i5 / i3 / Pentium / Celeron


ซีพียู CPU TDP (Thermal Design Power) สูงสุด: 95Watt
* เข้าชมได้ที่ www.biostar.com.tw สำ�หรับรายการซีพียูที่สนับสนุน
ชิพเซ็ต INTEL® H110
สนับสนุน Dual Channel DDR4 1866/2133/2400
รองรับหน่วยความจำ� 2 สล็อต DDR4 DIMM สูงสุดถึง 32 GB
หน่วยความจำ� ทุก DIMM สนับสนุนโมดูล non-ECC 4/8/16GB DDR4
* DDR4-2400 สำ�หรับ 7 โปรเซสเซอร์Intel® Core ™ Processor ครอบครัว
* เข้าชมได้ที่ www.biostar.com.tw สำ�หรับรายการหน่วยความจำ�ที่สนับสนุน
กราฟฟิก รวมกราฟฟิกอยู่ในซีพียู
สตอเรจ 4x SATA III พอร์ตเชื่อมต่อ
RTL8111H
แลน
10/ 100/ 1000 Mb/s การเจรจาอัตโนมัติ, ความสามารถในการเพล็กซ์ Half / Full
ALC887
ออดิโอ โคเดก
7.1 Channels, High Definition Audio
4x USB 3.0 พอร์ต (2 พอร์ตด้านหลัง I/O และ 2 พอร์ต ผ่านพอร์ตเชื่อมต่อด้านใน)
ยูเอสบี
6x USB 2.0 พอร์ต (2 พอร์ตด้านหลัง I/O และ 4 พอร์ต ผ่านพอร์ตเชื่อมต่อด้านใน)
5x PCIe 2.0 x1 สล็อต (สำ�หรับการทำ�เหมือง Bitcoin, เปลี่ยนความเร็วในการ PCI-E 1.0 ในการตั้งค่า
สล็อตขยายเพิ่มเติม BIOS)
1x PCIe 3.0 x16 สล็อต
1x PS/2 เมาส์
1x PS/2 คีย์บอร์ด
1x DVI-D พอร์ต
1x LAN พอร์ต
พอร์ต I/O ด้านหลัง
2x USB พอร์ต (เพียง 5V พลังงาน, ไม่มี USB สัญญาณ)
2x USB 2.0 พอร์ต
2x USB 3.0 พอร์ต
3x Audio Jack
4x SATA III พอร์ตเชื่อมต่อ
2x USB 2.0 พอร์ตเชื่อมต่อ (หัวเชื่อมต่อทุกตัวรองรับ 2 พอร์ต USB 2.0)
1x USB 3.0 พอร์ตเชื่อมต่อ (หัวเชื่อมต่อทุกตัวรองรับ 2 พอร์ต USB 3.0)
1x 8-Pin Power พอร์ตเชื่อมต่อ
1x 24-Pin Power พอร์ตเชื่อมต่อ
2x 4-Pin Power พอร์ตเชื่อมต่อ (สำ�หรับการทำ�เหมือง Bitcoin, ขั้วต่อสายไฟ 4 PIN จะต้องติดตั้ง)
พอร์ต I/O ด้านใน 1x 15-Pin SATA Power พอร์ตเชื่อมต่อ (สำ�หรับการเพิ่มประสิทธิภาพไฟ USB)
1x พอร์ตเชื่อมต่อ CPU Fan
2x พอร์ตเชื่อมต่อระบบ Fan
1x พอร์ตเชื่อมแต่แผงด้านหน้า
1x พอร์ตเชื่อมต่อออดิโอด้านหน้า
1x พอร์ต Clear CMOS
1x พอร์ตเชื่อมต่อ Serial Port
รูปแบบจากโรงงาน ขนาน ATX จากโรงงาน, 210มม. x 295มม.
Windows 7 (32/64bit) / 8.1(64bit) /10(64bit)
* Windows 7 (32/64 บิต) / 8.1 (64 บิต) สำ�หรับ 6 โปรเซสเซอร์Intel® Core ™ Processor
สนับสนุน OS ครอบครัวเท่านั้น
* Biostar ขอสงวนสิทธิ์ในการเพิ่มหรือถอดการสนับสนุนสำ�หรับระบบปฏิบัติการ OS ต่างๆ
โดยไม่ต้องแจ้งให้ทราบล่วงหน้า

APPENDIX I: Specifications in Other Languages | 33


this page intentionally left blank

34 | APPENDIX I: Specifications in Other Languages


FCC条款
依照FCC条款第15部分的规定,本装置已经通过测试并且符合Class B级数字装置的限制。
此条款限制了在安装过程中可能造成的有害射频干扰并提供了合理的防范措施。本装置在
使用时会产生无线射频辐射,如果没有依照本手册的指示安装和使用,可能会与无线通讯
装置产生干扰。然而,并不保证在特定的安装下不会发生任何干扰。
如果关闭和重新开启本设备后,仍确定本装置造成接收广播或电视的干扰,用户可以使用
以下列表中的一种或多种方法来减少干扰:
•  重新安装或调整接收天线。
•  增加本设备与接收设备之间的距离。
•  连接设备连接到不同的插座以便于两个设备使用不同的回路。
•  咨询经销商或富有经验的无线电工程师,以获得更多资讯。
本用户手册内容的变更,恕不另行通知,制造商没有解释的义务。
本用户手册的所有内容若有任何错误,制造商没有义务为其承担任何责任。所有商标和产
品名称均有其各自所有权。
未经过书面许可,不得以任何形式(部分或全部)复制此手册信息。

免责说明
本手册内容系BIOSTAR®知识产权,版权归BIOSTAR®所有。我们本着对用户负责的态度,
精心地编写该手册,但不保证本手册的内容完全准确无误。BIOSTAR®有权在不知会用户
的前提下对产品不断地进行改良、升级及对手册内容进行修正,实际状况请以产品实物为
准。本手册为纯技术文档,无任何暗示及影射第三方之内容,且不承担排版错误导致的用
户理解歧义。本手册中所涉及的第三方注册商标所有权归其制造商或品牌所有人。

CE符合性简短声明
我们声明此产品符合现行标准,并满足2004/108/CE,
2006/95/CE 和1999/05/CE指令规定的所有基本要求。

防静电操作规则
静电可能严重损坏您的设备,在处理主板以及其它的系统设备的时候要特别注意,避免和
主板上的系统组件的不必要接触,保证在抗静电的环境下工作,避免静电放电可能对主板
造成损坏,当在您的机箱中插入或者移除设备时,请保证电源处于断开状态,厂商对于不
遵照本操作规则或者不遵守安全规范而对主板造成的损坏不负责。
目录
第一章: 主板介绍������������������������������������������������������������������������������������������������������� 3
1.1 前言����������������������������������������������������������������������������������������������������������������������������������������������� 3
1.2 包装清单��������������������������������������������������������������������������������������������������������������������������������������� 3
1.3 主板特性��������������������������������������������������������������������������������������������������������������������������������������� 4
1.4 后置面板接口������������������������������������������������������������������������������������������������������������������������������ 5
1.5 主板布局图���������������������������������������������������������������������������������������������������������������������������������� 6
第二章: 硬件安装������������������������������������������������������������������������������������������������������� 7
2.1 中央处理器(CPU)����������������������������������������������������������������������������������������������������������������������� 7
2.2 散热片������������������������������������������������������������������������������������������������������������������������������������������� 9
2.3 风扇接头������������������������������������������������������������������������������������������������������������������������������������� 10
2.4 系统内存������������������������������������������������������������������������������������������������������������������������������������� 10
2.5 扩展槽����������������������������������������������������������������������������������������������������������������������������������������� 12
2.6 跳线设置������������������������������������������������������������������������������������������������������������������������������������� 13
2.7 接口和插槽�������������������������������������������������������������������������������������������������������������������������������� 14
第三章: UEFI BIOS和软件��������������������������������������������������������������������������������������� 18
3.1 UEFI BIOS设置������������������������������������������������������������������������������������������������������������������������� 18
3.2 刷新BIOS������������������������������������������������������������������������������������������������������������������������������������ 18
3.3 软件��������������������������������������������������������������������������������������������������������������������������������������������� 22
第四章:帮助信息������������������������������������������������������������������������������������������������������ 25
4.1 驱动程序安装注意事项����������������������������������������������������������������������������������������������������������� 25
4.2 AMI BIOS 哔声代码���������������������������������������������������������������������������������������������������������������� 26
4.3 AMI BIOS 开机自检代码�������������������������������������������������������������������������������������������������������� 26
4.4 问题解答������������������������������������������������������������������������������������������������������������������������������������� 28
附录I:产品中有毒有害物质或元素的名称及含量����������������������������������������������� 29

2 | 目录
TH110-BTC

第一章: 主板介绍

1.1 前言
感谢您选购我们的产品,在开始安装主板前,请仔细阅读以下安全指导说明:
•  选择清洁稳定的工作环境。
•  操作前请确保计算机断开电源。
•  从抗静电袋取出主板之前,先轻触安全触地器或使用触地手腕带去除静电以确保安
全。
•  避免触摸主板上的零件。手持电路板的边缘,不要折曲或按压电路板。
•  安装之后,确认没有任何小零件置于机箱中,一些小的零件可能引起电流短路并可能
损坏设备。
•  确保计算机远离危险区域,如:高温、潮湿、靠近水源的地方。
•  计算机的工作温度应保持在0-45℃之间
•  为避免受伤,请注意以下幾點:
主板或連接器上尖銳的針腳
机箱上的粗糙边缘和尖角
破损的线缆可能引起短路

1.2 包装清单
•  Serial ATA数据线 x2
•  ATX机箱后置I/O面板 x1
•  用户手册 x1
•  驱动光盘 x1 (包括安装驱动)

»  此清单可能因销售区域或主板型号不同而异,相关标配详情请咨询当地经销商。

第一章: 主板介绍 | 3
1.3 主板特性
规格
Socket 1151,Intel Core i7 / i5 / i3 / Pentium / Celeron处理器
CPU支援 CPU最大热功耗(95Watt)
* 请访问 www.biostar.com.tw 获取CPU的支持列表
芯片组 INTEL® H110
支持双通道DDR4 1866/2133/2400
2个DDR4 DIMM插槽,最大内存容量为32GB
内存 每个DIMM支持非ECC 4/ 8/ 16 GB DDR4内存模组
* DDR4-2400用于第7代Intel®Core™处理器系列。
* 请访问 www.biostar.com.tw 获取内存的支持列表。
存储器 4个SATA III接口 (6Gb/s)
RTL8111H
网络
10/ 100/ 1000 Mb/s自适应传输模式,半双工/全双工工作模式
音效 ALC887 ; 8声道音频输出
4个USB 3.0端口 (背板2个端口,板载接头支持2个端口)
USB
6个USB 2.0端口 (背板2个端口,板载接头支持4个端口)
5个PCIe 2.0 x1插槽 (当使用比特币挖扩时,请在BIOS设置中将速度更改为PCI-E 1.0)
扩展槽
1个PCIe 3.0 x16插槽
1个PS/2鼠标接口
1个PS/2键盘接口
1个DVI-D端口
1个LAN端口
背板接口
2个USB 端口(仅提供5V电源)
2个USB2.0端口
2个USB3.0端口
3个音频插孔
4个SATA III接口 (6Gb/s)
2个USB2.0接头(每个接头支持2个USB2.0端口)
1个USB3.0接头(每个接头支持2个USB3.0端口)
1个电源接口(8针)
1个电源接口(24针)
2个电源接口(4针) (当使用比特币挖扩时,必须安装4pin电源连接器)
板载接口 1个SATA电源接口(15针) (增强USB电源)
1个CPU风扇接头
2个系统风扇接头
1个前置面板接头
1个前置音频接头
1个清空CMOS数据接头
1个COM输出接头
主板尺寸 ATX Form Factor, 295 mm x 210 mm
Windows 7 (32/64bit)/ 8.1(64bit) /10(64bit)
操作系统支持 * Windows 7(32/64位)/ 8.1(64位)仅适用于第6代Intel®Core™处理器系列。
* 如有增加或减少任何OS支持,Biostar保留不预先通知的权利。

4 | 第一章: 主板介绍
TH110-BTC

1.4 后置面板接口

»  仅Intel集成显卡处理器支持DVI-D端口。
»  最高分辨率:
DVI-D: 1920 x 1200 @60Hz
»»  当使用前置HD音频插孔并插入耳机/麦克风时,后置声音将自动禁用。
»  配置8声道音频输出,您必须使用HD前面板音频模块,才能够通过O.S.多声道音频功能音频工
具。
»  该USB5V端口只为您的配件提供5V的电源。(例如耳机和USB充电器设备。)

2/ 4/ 5.1/ 7.1-声道模式配置
音频接口 2 声道模式 4 声道模式 5.1 声道模式 7.1 声道模式
蓝色 (背部面板) 线性输入 线性输入 线性输入 侧边声道输出
绿色 (背部面板) 线性输出 前置声道输出 前置声道输出 前置声道输出
粉红色 (背部面板) 麦克风输入 麦克风输入 中置/重低单声道输出 中置/重低单声道输出
草绿色 (前置面板) 耳机 后置声道输出 后置声道输出 后置声道输出

第一章: 主板介绍 | 5
1.5 主板布局图

»  标示为针脚1

6 | 第一章: 主板介绍
TH110-BTC

第二章: 硬件安装

2.1 中央处理器(CPU)
步骤1: 找到主板上的CPU插槽。

»  安装前请取掉针脚保护盖,并妥善保管以备后用。移开CPU后,请盖上保护盖以确保针脚不被损
坏。
»  主板可能配有两种不同的针脚保护盖,请参照以下指示取掉保护盖。
步骤2: 将拉杆从插槽移出并向上抬起

步骤3: 取掉针脚保护盖

第二章: 硬件安装 | 7
步骤4: 按照箭头的指示方向,将CPU上的切口对准插槽上相应的位置,然后将CPU放入
插槽处

步骤5: 固定CPU,将拉杆闭合。

»  请确保安装专为LGA1151插座設計的CPU。
»  CPU必须按正确的方向放入,不要强行将CPU放进插槽以免损坏CPU。

8 | 第二章: 硬件安装
TH110-BTC

2.2 散热片
步骤1: 请将CPU风扇组件置于CPU顶部,确保四个钉钩对齐主板上的插孔,调整其方
位,使风扇电线与CPU风扇接口间距最近。确保钉钩插槽垂直指向散热片。

步骤2: 依次把对角2个钉钩同时向下按,以固定风扇,完成CPU安装。

»  如有必要, 在安装散热风扇前请先涂抹散热膏于CPU表面。
»  请务必连接CPU风扇接口。
»  请参照CPU散热片的安装手册获取正确的安装信息。

第二章: 硬件安装 | 9
2.3 风扇接头
此风扇接头支持电脑内置的冷却风扇,风扇引线和插头可能因制造商而异。
CPU_FAN1: CPU 风扇接头

Pin Assignment
1 接地
2 +12V
3 FAN RPM rate sense
4 Smart Fan Control (By Fan)

SYS_FAN1/ SYS_FAN2: 系统风扇接头

Pin Assignment
1 接地
2 +12V
3 FAN RPM rate sense
4 Smart Fan Control (By Fan)

»  CPU_FAN1,SYS_FAN1,SYS_FAN2支持4针脚和3针脚接口;接线时请注意红线是正极需接到
第二个针脚,黑线接地需接到GND针脚。

2.4 系统内存
DDR4内存模组

10 | 第二章: 硬件安装
TH110-BTC

步骤1: 向外推开固定夹,打开DIMM插槽。将DIMM按顺序放在插槽上, DIMM上的切


口须与插槽凹口匹配。

步骤2: 垂直插入DIMM并固定好,直到固定夹跳回原位,DIMM就位。

»  如果DIMM未顺利插入,请勿强行按压。将DIMM拔出,再重插一次。

内存容量
DIMM插槽位置 DDR4模组 最大内存容量
DIMMA1 4GB/8GB/16GB
32GB
DIMMB1 4GB/8GB/16GB

双通道内存安装
为激活主板双通道功能,使用内存模组必须符合以下要求:
成对安装相同密度的内存模组。
如下表所示
双通道状态 DIMMA1 DIMMB1
Disabled O X
Disabled X O
Enabled O O
(“O”表示内存已安装,“X ”表示内存未安装。)

»  当安装多个内存模块時,我们建议使用相同品牌和容量的内存於主板上。

第二章: 硬件安装 | 11
2.5 扩展槽
PEX16_1: PCI-Express Gen3 x16 插槽
•  符合PCI-Express 3.0规范。
•  同步单向最大理论带宽为16GB/s,总带宽为32GB/s。
PEX1_1/ PEX1_2/ PEX1_3/ PEX1_4/ PEX1_5: PCI-Express Gen2 x1 插槽
•  符合PCI-Express 2.0规范。
•  同步单向最大理论带宽为0.5GB/s,总带宽为1GB/s。

安装扩展卡
请参照以下步骤安装扩展卡:
•  安装扩展卡前请阅读扩展卡的相关指示说明。
•  打开电脑机箱后盖,移除螺丝和插槽支架。
•  将扩展卡按照正确的方向插入插槽,直到扩展卡完全就位。
•  用螺丝将扩展卡的金属支架固定到机箱后置面板。
•  还原电脑机箱后盖。
•  开机。如有必要,可为扩展卡更改BIOS设置。
•  安装扩展卡的驱动。

12 | 第二章: 硬件安装
TH110-BTC

2.6 跳线设置
下图展示如何设置跳线。当跳帽放置在针脚上时,跳线为闭合(close)状态。否则跳线为
断开(open)状态。
Pin 打开 Pin 闭合 Pin 1-2 闭合

JCMOS1: 清空CMOS 跳线
用户可清空CMOS数据并恢复BIOS安全设置,请按照以下步骤操作以免损坏主板。

Pin 1-2 打开: 正常操作(默认)

Pin 1-2 闭合: 清空CMOS数据

清空CMOS数据过程:
1. 断开AC电源。
2. 将跳线设置成1-2接脚闭合,建议可以使用一个金属物体如螺丝刀触碰1-2接脚。
3. 等待5秒钟。
4. 清空CMOS数据後,请确认跳线设置成1-2接脚打开。
5. 接通AC电源。
6. 开机然后按下<Del>键进入BIOS设置。

第二章: 硬件安装 | 13
2.7 接口和插槽
ATXPWR1: ATX电源接口
为了更好的兼容性,我们建议使用标准的ATX24-pin电源供应此接口的电源。
针 定义 针 定义
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 接地 3 接地
16 PS_ON 4 +5V
17 接地 5 接地
18 接地 6 +5V
19 接地 7 接地
20 NC 8 PW_OK
21 +5V 9 唤醒电压+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 接地 12 +3.3V

ATXPWR2: ATX电源接口
此接口给CPU电路提供+12V电压。若CPU电源插头为4针脚,请将其插入ATXPWR2的
1-2-5-6针脚。

针 定义
1 +12V
2 +12V
3 +12V
4 +12V
5 接地
6 接地
7 接地
8 接地

»  开机前,请确保ATXPWR1和ATXPWR2接口都已插上电源。
»  电压不足可能导致系统不稳或者外围设备不能正常运行。当配置使用大功率设备的系统时,建议
您使用带有大功率输出的电源。

14 | 第二章: 硬件安装
TH110-BTC

AUXPWR1/2: 图形辅助电源连接器
(當比特币挖擴使用時,必须安装4pin电源连接器)
此连接器是用于显卡的辅助电源连接。 显卡的独占电源提供更好的图形性能。

针 定义
1 +12V
2 接地
3 接地
4 +5V

SATA_POWER: SATA电源接口
此SATA电源连接器增强后端USB端口的电源。

针 定义 针 定义
1 VCC3 9 VCC5
2 VCC3 10 接地
3 VCC3 11 N/A
4 接地 12 接地
5 接地 13 12V
6 接地 14 12V
7 VCC5 15 12V
8 VCC5 -- --

PANEL1: 前置面板接头
此16针脚接口包含开机,重启,硬盘指示灯,电源指示灯和扬声器接口。
针 定义 功能 针 定义 功能
1 +5V 9 N/A
N/A
2 N/A 10 N/A
扬声器
3 N/A 11 N/A N/A
接口
Power LED
4 扬声器 12
(+)
Power LED 电源指
5 HDD LED (+) 13
硬盘指 (+) 示灯
示灯 Power LED
6 HDD LED (-) 14
(-)
7 接地 重启按 15 电源按钮 开机按
8 Reset control 钮 16 接地 钮

第二章: 硬件安装 | 15
SATA3_1/3_2/3_3/3_4: 串行ATA接口
此接口通过SATA数据线连接SATA硬盘。

针 定义
1 接地
2 TX+
3 TX-
4 接地
5 RX-
6 RX+
7 接地

JFRONT_USB3_1: 前置面板USB 3.0接头


PC前置面板支持附加的USB数据线,也可连接即插即用外围设备。

针 定义 针 定义
1 VBUS0 11 D2+
2 SSRX1- 12 D2-
3 SSRX1+ 13 接地
4 接地 14 SSTX2+
5 SSTX1- 15 SSTX2-
6 SSTX1+ 16 接地
7 接地 17 SSRX2+
8 D1- 18 SSRX2-
9 D1+ 19 VBUS1
10 ID 20 Key

F_USB1/2: 前置面板USB 2.0接头


PC前置面板支持附加的USB数据线,也可连接即插即用外围设备。

针 定义
1 +5V (fused)
2 +5V (fused)
3 USB-
4 USB-
5 USB+
6 USB+
7 接地
8 接地
9 Key
10 NC

16 | 第二章: 硬件安装
TH110-BTC

F_AUDIO1: 前置面板音频接头
此接头可连接音频输出数据线,支持HD(高清)音频和AC’97。
HD Audio AC’97
针 定义 针 定义
1 Mic Left in 1 Mic In
2 接地 2 接地
3 Mic Right in 3 Mic Power
4 GPIO 4 Audio Power
5 Right line in 5 RT Line Out
6 Jack Sense 6 RT Line Out
7 Front Sense 7 Reserved
8 Key 8 Key
9 Left line in 9 LFT Line Out
10 Jack Sense 10 LFT Line Out

»  建议您连接前置高清音频插孔,享用主板高清音频功能。
»  如果要连接AC’97前置音频输出数据线,请关闭”前置面板插孔检测功能” 。此功能在系统音
频工具中可见。

COM1: 串行端口
此主板有一串行端口,可连接至RS-232端口。
针 定义
1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send
8 Clear to send
9 Ring indicator
10 Key

第二章: 硬件安装 | 17
第三章: UEFI BIOS和软件

3.1 UEFI BIOS设置


•  BIOS设置程序可用于查看和更改计算机的BIOS设置。开机自检时,按<DEL>键可进入
BIOS设置程序。
•  更多相关UEFI BIOS设置信息,请参考网站上的UEFI BIOS手册。

3.2 刷新BIOS
以下任意一种工具都可以刷新BIOS:
•  BIOSTAR BIOS Flasher: 使用此工具,BIOS可通过硬盘上的文件刷新,USB驱动刷新,
或者CD-ROM 刷新。
•  BIOSTAR BIOS刷新工具: 能够在Windows 环境下自动刷新。使用此工具,BIOS可通
过硬盘上的文件刷新, USB驱动刷新,CD-ROM 刷新或者从网站上的文件地址刷新。
BIOSTAR BIOS Flasher

»  此工具仅允许可使用FAT32/16格式化或单个分区的存储设备。
»  刷新BIOS时如关机或重启系统将导致系统引导失败。
使用BIOSTAR BIOS Flasher刷新BIOS
1. 进入网站下载与主板相匹配的最新BIOS文件。
2. 然后保存BIOS文件到U-盘。(仅支持FAT/FAT32格式)
3. 插入包含BIOS文件的U-盘到USB接口
4. 开机或重启后,在自检过程中按<F12>键。.

5. 进入自检后,屏幕会弹出BIOS-FLASHER工
具。选择<fs0>搜索BIOS文件。

6. 选择合适的BIOS文件,并按”Yes” 执行
BIOS刷新程序。

18 | 第三章: UEFI BIOS和软件


TH110-BTC

7. BIOS刷新后会弹出是否重启系统的对话框。
按<Y>重启系统

8. 系统引导并出现相关标识信息时,按<DEL>键进入BIOS设置。
选择<Save & Exit>,使用<Restore Defaults>功能加载系统默认值,然后选择<Save
Changes and Reset>来重启系统,完成BIOS刷新。
BIOS刷新工具(通过网络)
1. 用DVD驱动安装BIOS Update Utility。
2. 使用此功能时,请确保电脑联网。

3. 打开BIOS刷新工具,然后点击”Online
Update”按钮。

4. 屏幕弹出是否执行刷新BIOS程序的对话请
求,点击”Yes”开始刷新BIOS。

5. 如果BIOS有新版本,屏幕会弹出提示您下
载最新版本的对话框。点击”Yes”下载。

6. 完成下载后,屏幕弹出提示您刷新
BIOS的对话框,点击”Yes”开始刷新。

第三章: UEFI BIOS和软件 | 19


7. 刷新程序结束后,屏幕弹出提示您重启系
统的对话框。点击”OK”重启系统。

8. 系统引导并出现相关标识信息时,按<DEL>键进入BIOS设置。
选择<Save & Exit>,使用<Restore Defaults>功能加载系统默认值,然后选择<Save
Changes and Reset>来重启系统,完成BIOS刷新。
BIOS刷新工具(通过BIOS文件)
1. 用DVD驱动安装BIOS刷新工具。
2. 从我们的网站www.biostar.com.tw 下载合适的BIOS.

3. 在主页面打开BIOS Updat Utility,然后点


击”Update BIOS”按钮。

4. 屏幕弹出是否执行刷新BIOS程序的对话请
求,点击”OK”开始刷新BIOS。

5. 选择BIOS文件的存放目录。然后选择合适的
BIOS文件,点击”Open”。
刷新BIOS要花几分钟时间,请耐心等待。

6. BIOS刷新过程结束后,点击”OK”重启系
统。

20 | 第三章: UEFI BIOS和软件


TH110-BTC

7. 系统引导并出现相关标识信息时,按<DEL>键进入BIOS设置。
选择<Save & Exit>,使用<Restore Defaults>功能加载系统默认值,然后选择<Save
Changes and Reset>来重启系统,完成BIOS刷新。

BIOS备份
点击BIOS备份按钮,选择存储备份文件的合适
目录,然后点击”Save”。

第三章: UEFI BIOS和软件 | 21


3.3 软件
安装软件
1. 将光盘放入光驱,若Autorun功能已激活,驱动安装程序将会出现。
2. 选择Software Installation,然后点击各软件图标。
3. 根据屏幕上的指令完成安装。
启动软件
安装程序完成后,桌面上将出现软件图标。请双击图标启动软件工具。

»  所有软件的相关信息和内容若有变更,恕不另行通知。为使系统性能更佳,软件会不断升级。
»  下面的图片和信息仅供参考,此主板的实际信息和设置可能与手册稍有差异。

BIOScreen 工具
此实用工具可以将开机画面个性化。您可以选择BMP格式来自定义计算机开机画面。

请参照以下步骤来更新开机画面:
•  加载画面(Load Image):选择图片作为开机画面。
•  转换(Transform):转换图片并预览。
•  更新BIOS(Update Bios):将图片写入BIOS内存,然后完成更新。

22 | 第三章: UEFI BIOS和软件


TH110-BTC

eHot-Line
eHot-Line是有助于您联系技术支持系统的便捷工具。此工具将收集系统信息,当您遇
到问题时,可提供有利分析,并发送这些信息至我们的技术支持部门,从而帮助解决此
问题。

填好表格信息后,点击“Send”发送邮件。将
出现一个确认信息对话框;点击“Send”确认
发送点击“Do Not Send”则取消操作。

如您想保存此信息到文本文件里,点击“Save
As…”,出现一个保存对话框,输入文件名即
可。

第三章: UEFI BIOS和软件 | 23


输入文件名,点击“Save”,系统信息将被保
存至文本文件里。

打开已保存的文本文件,显示相关系统信息(包
括主板/BIOS/CPU/视频设备/OS)。这些信息
当然也在已发送的邮件里。

»  在使用此工具前,请将Outlook Express设置为您的默认电子邮件连接程序。
»  我们将为用户资料保密,所以使用eHot-Line服务时,请放心提供您的系统信息。
»  若您未将Outlook Express设置为默认电子邮件连接程序,也可保存您的系统信息到文件里,然
后用其它电子邮件工具发送此文件到我们的技术支持。
请访问网站http://www.biostar.com.tw/app/en/about/contact.php获取我们的联系信息。

24 | 第三章: UEFI BIOS和软件


TH110-BTC

第四章:帮助信息

4.1 驱动程序安装注意事项
为获得更好的系统性能,在操作系统安装完成后,请插入您的系统驱动到光驱并安装。
插入DVD后,将出现如下所示窗口。

此设置向导将自动检测您的主板和操作系统。
A. 驱动程序安装
安装驱动程序,请点击驱动器图标。设置向导将列出主板兼容驱动和操作系统。点击各
设备驱动程序,以开始安装进程。
B. 软件安装
安装软件,请点击软件图标。设置向导将列出系统可用软件,点击各软件名称,以开始
安装进程。
C. 使用手册
除了书本形式的手册,我们也提供光盘形式的使用指南。点击Manual图标,浏览可用
相关使用指南。

»  在插入驱动之后,如此窗口未出现,请用文件浏览器查找并执行SETUP.EXE文件。
»  若需要Acrobat Reader打开manual文件。请从网站http://get.adobe.com/reader/下载最新
版本的Acrobat Reader软件。

第四章:帮助信息 | 25
4.2 AMI BIOS 哔声代码
引导模块哔声代码
哔声次数 含义
持续哔声 持续哔声

BIOS 开机自检哔声代码
哔声次数 含义
1 系统引导成功
8 显存错误(系统视频适配器)

4.3 AMI BIOS 开机自检代码


代码 含义
10 PEI核心启动
11 CPU Pre-memory初始化启动
15 北桥Pre-memory初始化启动
19 南桥Pre-memory初始化启动
2B 内存初始化,读取SPD数据
2C 内存初始化,检测Memory presence
2D 内存初始化,编程内存时序信息
2E 内存初始化,配置内存
2F 内存初始化(其他)
31 内存安装完成
32 CPU post-memory初始化启动
33 CPU post-memory初始化,Cache初始化
34 CPU post-memory初始化,应用处理器初始化
35 CPU post-memory初始化,选择BSP
36 CPU post-memory初始化,系统管理模式初始化
37 北桥Post-Memory初始化启动
3B 北桥Post-Memory初始化
4F DXE IPL启动
60 DXE核心启动
F0 固件引起的恢复条件(自动恢复)
F1 用户引起的恢复条件(强制恢复)
F2 恢复进程启动
F3 找到固件恢复图象
F4 加载固件恢复图象
E0 S3唤醒启动
E1 执行S3启动脚本
E2 重新发送影像
E3 系统S3待机导向
60 DXE内核启动
61 NVRAM初始化
62 安装南桥运行期
63 CPU DXE初始化启动
68 PCI HB初始化
69 北桥DXE初始化
6A 北桥DXE SMM初始化启动

26 | 第四章:帮助信息
TH110-BTC

代码 含义
70 南桥DXE初始化启动
71 南桥DXE SMM初始化启动
72 南桥设备初始化
78 南桥DXE初始化
79 ACPI模组初始化
90 引导设备选择阶段启动
91 驱动连接启动
92 PCI总线初始化启动
93 PCI总线热拔插控制器初始化
94 PCI总线列举
95 PCI总线请求资源
96 PCI总线分配资源
97 控制台输出设备连接
98 控制台输入设备连接
99 高级IO初始化
9A USB初始化启动
9B USB复位
9C USB检测
9D USB启用
A0 IDE初始化启动
A1 IDE复位
A2 IDE检测
A3 IDE启用
A4 SCSI初始化启动
A5 SCSI复位
A6 SCSI检测
A7 SCSI启用
A8 设置校对密码
A9 设置开始
AB 设置输入等待
AD 准备启动环境
AE 传统启动环境
AF 退出启动环境
B0 虚拟地址图开始
B1 虚拟地址图结束
B2 传统可选ROM初始化
B3 系统复位
B4 USB热拔插
B5 PCI总线热拔插
B6 清理NVRAM
B7 配置复位(NVRAM设置复位)

»  如此窗若出现表格未列出的代码,请联系我们的技术支持。

第四章:帮助信息 | 27
4.4 问题解答
问题 解决方法
1. 系统没有电,电源指示灯不亮,电源风 1. 确定电源线是否接好。
扇不转动。 2. 更换线材。
2. 键盘上的指示灯不亮。 3. 联系技术支持。

系统不起作用。键盘指示灯亮,电源指示 用力按压内存两端,确保内存安置于插槽
灯亮,硬盘正常运作。 中。

1. 检查硬盘与主板的连线,确定各连线是
否确实接好,检查标准CMOS设置中的驱
系统不能从硬盘启动,能从光盘启动。 动类型。
2. 硬盘随时都有可能坏掉,所以备份硬盘
数据是很重要的。

1. 备份数据和应用程序。
系统只能从光盘启动。硬盘能被读,应用
2. 重新格式化硬盘。用后备盘重新安装应
程序能被使用,但是不能从硬盘启动。
用程序和数据。

屏幕提示“Invalid Configuration” 或
“CMOS Failure”。
再次检查系统设备,确定设定是否正确
再次检查系统设备,确定设定是否正确
安装了第二个硬盘
1. 正确设置主/从硬盘跳线。
2. 运行安装程序,选择正确的驱动类型。
安装了第二个硬盘后,系统不能启动。
与驱动器厂商联系,寻求驱动兼容性的技
术支持。
CPU过热保护系统
在开启系统数秒后如有自动关机的现象,这说明CPU保护功能已被激活。CPU过热时,
防止损坏CPU,主机将自动关机,系统则无法重启。
此种情况下,请仔细检查。
1. CPU 散热器平放在CPU表面。
2. CPU风扇能正常旋转。
3. CPU风扇旋转速度与CPU运行速度相符。

确认后,请按以下步骤缓解CPU保护功能。
1. 切断电源数秒。
2. 等待几秒钟。
3. 插上电源开启系统。

或是:
1. 清除CMOS数据。(查看“Close CMOS Header: JCMOS1” 部分)
2. 等待几秒钟。
3. 重启系统。

28 | 第四章:帮助信息
TH110-BTC

附录I:产品中有毒有害物质或元素的名称及含量

有毒有害物质或元素

部件名称
六价铬 多溴联苯 多溴二苯醚
铅 (Pb) 汞 (Hg) 镉 (Cd)
(Cr(VI)) (PBB) (PBDE)

PCB板 O O O O O O

结构件 O O O O O O

芯片及其它
X O O O O O
主动零件

连接器 X O O O O O

被动电子元
X O O O O O
器件

焊接金属 O O O O O O

线材 O O O O O O

助焊剂,散
热 膏,标签 O O O O O O
及其它耗材

O:表示该有毒有害物质在该部件所有均质材料中的含量在SJ/T11363-2006标准规定的限量要求以下。
X:表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006标准规定的限量要求。
备注:在芯片及其它主动零件、连接器、被动电子元器件Pb栏位中有打X,表示Pb在该部件的某一均质材料中的含量超出
SJ/T11363-2006标准规定的限量要求,但均符合欧盟ROHS指令豁免条款。

附录I:产品中有毒有害物质或元素的名称及含量 | 29

You might also like