0 ratings0% found this document useful (0 votes) 45 views5 pagesChapt 806
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content,
claim it here.
Available Formats
Download as PDF or read online on Scribd
@eurcconter MAINTENANCE MANUAL MBB - BK117
006 HIGH DENSITY SEATS
‘Table of Contents
Paragraph Tike Pape
808-1 DESCRIPTION. HIGH DENSITY SEATS. 3
806-2 INSPECTION SCHEDULE - HIGH DENSITY SEATS, ‘4
808-3 INSPECTION FOR CONDITION - HIGH DENSITY SEAT 5
806-4 REMOVAL. HIGH DENSITY SEAT. 5
808-5 INSTALLATION - HIGH DENSITY SEAT. 5
CHAPTER 206
asec Page 12 Geurcconter MAINTENANCE MANUAL MBB - BK117
806-1 DESCRIPTION. HIGH DENSITY SEATS,
“Te higy gonsiy seats (1 gure 806-1) consist of ight ally rames which are upholstered with supatex
{avr Covered foam, The seat bostr ad back rest ave atached to tha fuselage by que rloase.
{stones, woe tho Seat loge ate connected fo receptacles nthe cabin oor by quickrelease sud
‘ings, Each sea provided with an aductatie laperaey bel shoulder Ramess. The ends of he
lap-Saiey bot are aftached fo fitngs situated ato an ether side of ho seat. The onde ofthe
"Shoulder hamass are pulled tough bucues located below the Head ret and ae Tastned by lamps to
form’ bop around te buckles,
CHAPTER B06
code © Pages Qeurccopter MAINTENANCE MANUAL MEB—BK17
11 806-2 INSPECTION SCHEDULE (REFER TO APPENDIX A)
(CHAPTER coe code ¢ Revision 16
Page Geuroconter MAINTENANCE MANUAL MBB - 8K117
806-9 INSPECTION FOR CONDITION HIGH DENSITY SEAT
1. Inept ame (3, gure 808-1) for deormation and riveting for concen
‘a, Replace deformed trame sections and damaged tings.
», Roplae loose vets. vet holes ave elongated it oversize rivets.
2, Inspect sat back rest and head rect upoleory for damage, Replace the fabric I damaged (torn)
2, Inspec sat tension cor for coniion
4. Totton loose cords,
», Replace worn a tatenod coeds.
4, Inspect shoulder hammesses and lap bots for conan. Replace damaged tems,
‘5, Check stud tings (9) fr postive locking action and or contin, Replace detect std ings.
6
“Check pip pins (10) for postive locking ation and for conation. Replace defective pip pins.
Inspect double studs (7 for postive locking action and or condition. Replace deleive double studs
806-4 REMOVAL- HIGH DENSITY SEAT
1. Discunnact stud tings (9, gue 806-1) from the receptacles inthe Hoo, Fold berch upward and
Soca wih fastona be (3)
2 Discunnect double std (7), detach seats and beam tube (), than lower seals te tor.
8. Rerrave pip pin (10) tom the contr post and remove brackets (11 and 12},
{806-5 INSTALLATION - HIGH DENSITY SEAT
1. Insta brackets (11 and 12) onthe center post with pp pins (10) to suppor the rearwar facing high
enaty seats,
2, Poston rearward:tacng LH or RH high density seats on he tor,
‘8, Posion beam tube (4) on the attachment fing ofthe fuselage. Atach double stds (7) tothe
Afachment ings and secure
4, tae folded high density seat tothe attachment ftingson the fuselage and secure with double
‘Sus
5, Looson fastener bl () tok down bench and nse stings (2) into receptacles inthe for.
CHAPTER 806
cove © Page 56 Geaxrcconter MPINTENANCE MANUAL MBB - BK117
Figure 806-1 Roreval and nstaatior
‘CHAPTER 806,
Page 78
