DAF TNR

DW53205501

en Operating and installation instructions

01_DAF_MMT_en.indd 1 25.01.13 12:00

 2

1 2 3 4 5

17 6
16 7
15 8
9

14 10

11

12

The text of this document has been translated from the German source. Translation may lead to
interpretation differencies regarding contents and meaning of the written text.
Therefore, in case of dispute, the German version of this document shall always be considered the
sole and authentic source for determining the contents and meaning of the written text.

01_DAF_MMT_en.indd 2 25.01.13 12:00

 Controls 3

1 button ; button
Switch between the daytime and Return to the parent menu.
night-time display illumination (short
press); switch the display on/off (long < Buttons 1 - 6 for radio station presets
press).
= Left control knob
2 CD slot for audio/MP3 CDs. Adjust the volume (rotate); switch the unit
on/off (press).
3 Display / touch screen
> MEDIA button
4 MAP button Select the CD, USB, AUX or Bluetooth-
Display the map. audio source.

5 button ? BAND button

Eject the CD. Activate radio mode / switch between the
FM1, FM2 and AM wavebands (memory
6 NAV button banks).
Activate navigation mode.
@ and button
7 TRAF button In radio mode: Tune to stations automati-
Open the “traffic information” menu. cally.
In CD/MP3 mode: Select tracks (short
8 SETUP button press), begin fast forward (long press).
Open the settings menu.

9 SD card slot.

: Right control knob

Select a menu item or adjust a setting
(rotate); open a menu or confirm a setting
(press).

01_DAF_MMT_en.indd 3 25.01.13 12:00

 4 Table of Contents

Table of Contents
6 General information 14 Radio
6 Intended use 14 Switching on the radio
6 Disposal of end-of-life appliances 14 Selecting the frequency band
15 Radio Data System (RDS)
7 Introduction 15 RDS regional mode
7 General information 15 Activating/deactivating RDS regional
7 Radio reception mode
8 Operating modes 15 Traffic announcements (TA)
8 Radio 16 Activating/deactivating priority for
8 Media traffic announcements (TA)
8 Navigation 16 Radio station tuning
8 Operation 16 Automatic seek tuning
8 Controls 16 Manual station tuning
9 Multifunction knob 17 FM station list
9 Switching on the system 17 Storing a station
9 Automatic switch-off 18 Accessing a station
9 Adjusting the volume
9 Scrolling through a list of menu items
9 Adjusting settings
10 System settings
12 Navigation setup
12 Bluetooth
12 Traffic announcements setup
12 Radio settings
12 Volume settings
12 Adjusting the volume of traffic
announcements (TA)
13 Adjusting the volume of the AUX input
sources (if available)
13 Adjusting the speed dependent
volume
13 Adjusting the volume of spoken
announcements (navigation)
13 Reversing camera (optional)

01_DAF_MMT_en.indd 4 25.01.13 12:00

 Table of Contents 5

18 Media 26 Navigation
18 CD player 27 General information
18 General information 27 Navigation system functions
18 Important information about audio 27 TMC traffic information system and
CDs and MP3/WMA CDs dynamic navigation
19 Starting CD playback 27 Map data
20 Selecting a track 28 Vehicle attributes
20 Skipping to the next or previous track 28 Map options
20 Fast forwarding or fast reversing 29 Store current position
21 Mix mode 29 Show position information
21 Repeat mode 29 Show destination information
21 Ejecting a CD 29 NAV button and NAVIGATION menu
21 USB port 29 Entering a destination
21 General information 31 Home address
22 Important information 31 Route
22 Playing audio files via USB 32 Changing the time display mode
23 Playing audio files from an iPod 32 Previous destinations
23 Bluetooth audio connection 33 Options
23 Important information 33 Stopping route guidance
23 Bluetooth connection 33 TRAFFIC INFO menu
23 Connecting a Bluetooth device 34 Block
24 Connecting to another paired device 34 TA
24 Deleting a paired device 34 Route
25 Operation 34 All
25 AUX connection 35 SETUP button and NAVIGATION menu
25 General information 37 Information in the map view
25 Usage 39 User-defined points of interest
41 Maps
41 Navigation SD card
41 Changing a navigation SD card

42 Steering wheel remote control

42 Functions of the steering wheel
remote control

42 Technical data

01_DAF_MMT_en.indd 5 25.01.13 12:00

 6 General information

General information Risk of injury

Thank you for choosing a Bosch product. We This device is a CLASS 1 laser
hope you enjoy using this new piece of product.
equipment. ff Never look into the laser beam.
Please read these operating instructions ff Never try looking inside the
before using the equipment for the first time. housing or try opening the
We provide a manufacturer’s warranty on our housing.
products bought within the European Union. In ff You must only allow qualified
the case of devices bought outside the experts to perform any servicing
European Union, the warranty conditions work.
issued by our representative responsible for
the respective country will apply.
Disposal of end-of-life appliances
Intended use Please do not dispose of your old
The device has been designed for operation in appliance in the household refuse.
a commercial vehicle with a 12 V electrical To dispose of the old appliance,
system and for installation in a 2-DIN slot. please use the available waste return
and recycling systems.
Road safety
Road safety has absolute priority.
ff Familiarize yourself with the
device before setting off on your
journey.
ff Only operate this device if the
driving situation and traffic situa-
tion allow you to do so.
You must always be able to hear
police, fire service and ambulance
sirens in good time from inside your
vehicle.
ff For this reason, listen to your
sound system at an appropriate
volume level during your journey.

01_DAF_MMT_en.indd 6 25.01.13 12:00

 Introduction 7

Introduction
General information

Mode Feature
Radio ff FM - memory for 12 station presets
ff AM - memory for 6 station presets

Internal CD drive Plays audio-CDs and MP3/WMA CDs

Connectivity with ff iPod

external storage media ff MP3 player
ff USB flash drive
ff Portable CD players
ff Other mass storage via cable or Bluetooth

Navigation system Dynamic route directions for avoiding traffic jams or other traffic
problems

Notes ff Some areas – such as one-way

ff The system must be used in such roads, entrances and pedestrian
a way that you can drive the precincts, where access is
vehicle safely at all times. If in forbidden – may not be marked
doubt, you should stop your on the navigation map. The
vehicle and operate the system device will not issue any warning
while the vehicle is stationary. notices in such areas. You must
ff Using the navigation system comply with the traffic regulati-
does not excuse the driver from ons here.
driving and acting in a correct
and attentive manner as a road Radio reception
user. Traffic regulations must Radio reception may deteriorate due to
always be complied with. If you at-mospheric interference, noise, distortion or
need to operate the system (for reception interference caused, for instance,
instance, in order to enter an by:
address), stop your vehicle in a ff A change in the distance to the transmitter
safe place and then perform the ff Multipath reception due to reflection or
necessary function. shadowing

01_DAF_MMT_en.indd 7 25.01.13 12:00

 8 Introduction

Operating modes function really should be carried

out. The messages may also ask
Radio you to conclude the function.
ff Press the BAND button ? to switch on Press the button :, if you
the radio. want to suppress such a
See the “Radio” chapter for further message without initiating a
details. system function.

Media Operation
ff Press the MEDIA button > to activate a
CD, MP3 CD, iPod, USB, BLUETOOTH Controls
AUDIO or AUX function (if available). The system can be operated using the knobs
Details on this are available in the “Media” and buttons as well as the menus displayed on
chapter. the touch screen.
Furthermore, it is possible to operate the
Navigation system via a steering wheel remote control, if
ff Press the NAV button 6 to open the applicable.
NAVIGATION menu.
Details on this are available in the Touch screen
“Navigation” chapter. The system’s screen has a touch-sensitive
ff Press the MAP button 4 to display the surface that enables you to directly select the
road map indicating your vehicle’s current displayed menu options. For instance, it is
position. possible to activate an on-screen menu option
Details on this are available in the by tapping the button with a finger or to change
“Navigation” chapter. the position of a movable item on the screen by
moving it with your finger.
Notes
ff In the main menus for Audio, Risk of damage to the touch
only the buttons in the lower part screen
of the menus on the touch Do not use any pointed or hard
screen can be used. Operation objects, such as pens or pencils, to
using the right control knob : operate the touch screen.
is not possible.
ff Before a system function is
carried out, a message will often
appear asking you to confirm
whether the selected system

01_DAF_MMT_en.indd 8 25.01.13 12:00

 Introduction 9

Multifunction knob Automatic switch-off

To navigate through the menu options, If you switch on the system while the vehicle
ff turn the control knob : clockwise or ignition is off, the system will switch off
anticlockwise. automatically after one hour.
To activate the selected menu item,
ff press the control knob :. Adjusting the volume
This activates the respective system function ff Turn the control knob =.
or causes a message or submenu with further The current setting is displayed. When you
options to be displayed. switch on the system, the volume level that was
selected last will be set.
Notes ff Press the control knob = to mute the
ff In the main menus for Audio, unit or to return to the original volume.
only the buttons in the lower part If you mute the volume, the symbol
of the menu can be selected/ appears in the display.
activated via the touch screen.
ff Before a system function is Note
carried out, a message will often The mute function is deactivated
appear asking you to confirm automatically as soon as you switch
that the selected system to a different audio source.
function really should be carried
out. The message may also ask Scrolling through a list of menu
you to conclude a function. items
Press the button ;, if you Using the touch screen:
want to suppress such a ff Tap the or button of the scroll
message without initiating a bar.
system function. or
ff Use your finger to move the slider of the
Switching on the system scroll bar up or down to scroll through the
ff Switch on the vehicle’s ignition. list.
The system switches on automatically. Using the control knob ::
ff Turn the control knob : clockwise or
Note anticlockwise to scroll through the list of
If it does not switch on automatically, menu items.
press the control knob =.
Adjusting settings
The following examples describe a method for
adjusting the settings available in the various

01_DAF_MMT_en.indd 9 25.01.13 12:00

 10 Introduction

menus by using the on-screen menu options or ff Select the relevant option to adjust the
the control knob :. screen brightness.
ff Select the relevant option to adjust the
System settings display to suit the lighting conditions of
The system’s default settings can be changed your surroundings.
in the “SYSTEM SETUP” menu.
ff Press the SETUP button 8 and tap on Notes
System. ff If you select “Automatic”, the
system switches automatically
between day and night mode.
ff The dots displayed below a
setting indicate that further
options are available. Tap on the
the area to see the other options.

Using the control knob ::

ff Turn the control knob : clockwise or
Using the touch screen: anticlockwise to select a menu item.
ff Tap on a menu item to change the setting. ff Turn the control knob : to change the
Using the control knob :: setting.
ff Turn the control knob : clockwise or
anticlockwise to select a menu item. Scrolling direction
ff Turn the control knob : to change the If you set the scrolling direction, you will only
setting. be able to scroll in this direction in order to
select a menu item.
Adjusting the display Selection using the control knob ::
ff Select the Display menu item. ff Set the scrolling direction to or .

Clock setup
ff Press the SETUP button 8.
ff Tap on System.
ff Tap on Clock.
ff Touch the relevant setup item and adjust it
on the display or using the control knob
:.

01_DAF_MMT_en.indd 10 25.01.13 12:00

 Introduction 11

Using this function you can: Audio settings:

ff Set the time display to 24-hour format Using the touch screen:
ff Set the clock automatically or manually ff To open the AUDIO SETUP menu, press
ff Activate summer time the SETUP button 8 and select Audio.
ff Set the time zone

Selecting the language

You can select the language in which menus
should be displayed from various languages.
The voice output will then also occur in this
language.
ff Select the Language menu item.
A list of languages is displayed.
ff Select the desired language. ff Tap one of the on-screen buttons ( /
You have successfully completed setting the , / , / ) to adjustment
language. the audio settings.

Activating/deactivating the touch click Notes

If the Touch Click option is activated, a click ff If a main audio menu is activa-
tone sounds each time you tap the screen. ted, you can alternatively use the
control knob :.
Activating/deactivating the system sounds ff The Audio button in the SETUP
If the System sounds option is activated, the menu cannot be selected if the
following actions of the user or system are unit has been muted.
acknowledged with a beep:
ff Radio: When a station is stored to one of ff Bass: Use this setting to adjust the low
the station preset buttons. frequencies of the audio source.
ff CD player: When fast forward/reverse is ff Treble: Use this setting to adjust the high
activated. frequencies of the audio source.
ff Navigation: When activating/deactivating ff Balance: Use this setting to adjust the
voice announcements in navigation mode. volume distribution between the vehicle’s
left and right loudspeakers.
ff Fader: Use this setting to adjust the
volume distribution between the vehicle’s
front and rear loudspeakers.

01_DAF_MMT_en.indd 11 25.01.13 12:00

 12 Introduction

Using the control knob :: Bluetooth

ff Turn the control knob : clockwise or Details on this are available in the “Media”
anticlockwise to select a menu item. chapter, in the “Bluetooth audio connection”
ff Press the control knob : to activate the section.
selected menu item.
The selected menu item is highlighted. Traffic announcements setup
ff Turn the control knob : clockwise or Details on this are available in the “Navigation”
anticlockwise to adjust the setting. chapter, in the section entitled “NAV button
ff Turn the control knob : to confirm the and Navigation menu”, in the subsection
setting. entitled “Traffic information menu”.
You have successfully adjusted the setting.
Radio settings
Resetting to the factory defaults Details on this are available in the “Radio”
Perform the following steps to reset all the chapter, in the section entitled “Radio Data
system settings and the unit’s memory to the System (RDS)”, in the subsection entitled
factory defaults. “Activating/deactivating RDS regional mode”.
ff In the SYSTEM SETUP menu, select
Factory settings. Volume settings
The volume of the spoken announcements can
be adjusted during the announcements using
the control knob = or in the “Navigation
Setup” menu.
The system saves the setting and applies it
automatically to all future spoken announce-
ments until the setting is changed again.

Adjusting the volume of traffic

ff Tap on Yes to reset the settings to their announcements (TA)
factory defaults. The volume of the traffic announcements can
be adjusted during the announcement using
Navigation setup the left control knob =. When the announce-
Details on this are available in the “Navigation” ment has ended or has been canceled, the
chapter, in the section entitled “SETUP button volume is reset automatically to the original
and NAVIGATION menu”. setting.

01_DAF_MMT_en.indd 12 25.01.13 12:00

 Introduction 13

Adjusting the volume of the AUX Notes

input sources (if available) ff If a main audio menu is activa-
The relative volume level of external audio ted, you can alternatively use the
sources (such as an MP3 player) can be control knob : to adjust a
adjusted in the “AUDIO SETUP” menu. setting.
ff The Audio button in the SETUP
menu cannot be selected if the
unit has been muted.

ff To adjust the degree of volume adjust-

ment, set the speed dependent volume
(Speed vol.) to a value between 0 and 5.

Note
ff To adjust the relative volume level for If you set the speed dependent
external audio sources, set the AUX Level volume control to 0, this will prevent
to “Quiet”, “Medium” or “Loud”. the volume from being boosted at
increased driving speeds.
Adjusting the speed dependent If you set the speed dependent
volume volume control to 5, this will cause
If the speed dependent volume control is the volume to be boosted by the
activated, the volume is adjusted automatically maximum amount at increased
to compensate for the road and wind noise driving speeds.
while driving.
ff Press the SETUP button 8 and tap on Adjusting the volume of spoken
Audio. announcements (navigation)
ff Press the SETUP button 8 and tap on
Navigation. If Voice Guidance is set to
“Off”, change the setting to “On”.
ff Adjust the Volume to the desired level.
Once you have adjusted the volume, you
will now hear the selected volume level.

Reversing camera (optional)

If a reversing camera is installed, its picture is
displayed on the screen automatically for as
long as the vehicle’s reverse gear is selected.

01_DAF_MMT_en.indd 13 25.01.13 12:00

 14 Introduction | Radio

Note: Radio
The picture from the reversing In the radio menus you can only use the touch
camera is hidden automatically as screen to select or activate the menu items.
soon as the vehicle’s forward speed
exceeds 5 km/h. Switching on the radio
ff Switch on the system.
ff Press the BAND button ?.
The radio is switched on. After you switch on
the radio, the station that was listened to last
will be played.

Note
If an RDS station is played, the
information about the station name
and program is displayed.

Selecting the frequency band

ff Press the BAND button ? once or
several times to set the desired frequency
band.
The station that was listened to last in the
selected frequency band is played.

Notes:
ff If the frequency band is changed
from FM1 to FM2 to AM or the
other way around, the currently
received station remains
activated. If the currently

01_DAF_MMT_en.indd 14 25.01.13 12:00

 Radio 15

received station is stored using Activating/deactivating RDS regio-

one of the station preset nal mode
buttons, the corresponding ff Press the SETUP button 8 and then tap
button number is shown in the on Radio Setup.
display. The RADIO SETUP menu is displayed.

ff There are two FM frequency

band menus. You can store 12
FM stations using the station
preset buttons.
ff There is one AM frequency band
menu. You can store six AM
stations using the station preset
buttons.
ff Set RDS Regional to “On” or “Off”.
Radio Data System (RDS) The RDS regional mode is activated or
RDS is a system that transmits encoded digital deactivated.
information. RDS provides information
services such as the station name, traffic Traffic announcements (TA)
information and radio text. The TA function is only available in FM radio
mode.
RDS regional mode If the TA function is activated and the system
Sometimes RDS stations broadcast different receives a traffic announcement from an RDS
programs on different frequencies depending station, the currently active audio source will
on the region. The system always tunes to the be interrupted.
best receivable frequency of the currently A message appears and you will hear the
playing RDS station. announcement.
If RDS regional mode is activated, the system During the announcement you can adjust the
uses only frequencies of the currently received volume only using the control knob =.
RDS station that are providing the same You can cancel the traffic announcement by
regional program. tapping on Cancel.
If RDS regional mode is deactivated, the When the traffic announcement has ended or
system uses the frequencies of the currently has been canceled, the volume is reset
received RDS station that are providing automatically to the original setting.
different regional programs.

01_DAF_MMT_en.indd 15 25.01.13 12:00

 16 Radio

Notes
ff If traffic announcements are
enabled, the radio remains
activated in the background even
if the CD player or navigation
system is activated.
ff If you previously selected a radio
station that does not broadcast
traffic announcements, the ff Briefly press the or button @.
system automatically tunes to a The next available radio station is received and
radio station that does broad- played automatically.
cast traffic announcements. The
traffic announcements are made Note
even if the AM frequency band If no other receivable station is found,
has been selected beforehand. the radio will retune to the station
This ensures that regional traffic that it was receiving last.
announcements can be received
at all times regardless of the Manual station tuning
selected operating mode. Using the control knob ::
ff In the “Radio” menu, turn the control knob
Activating/deactivating priority for : clockwise or anticlockwise to adjust
traffic announcements (TA) the receiving frequency.
Please read about this in the “Navigation” Using the frequency scale:
chapter, in the section entitled “NAV button ff Tap on Tune.
and Navigation menu”, in the subsection A frequency scale is displayed.
entitled “Traffic information menu”.

Radio station tuning

You can tune into the desired radio station
manually or automatically. Details are available
on this in the following sections.

Automatic seek tuning

ff Tap on Tune.
A frequency scale is displayed. Perform one of the following actions to
manually tune to the desired station.
ff Tap on the frequency scale.

01_DAF_MMT_en.indd 16 25.01.13 12:00

 Radio 17

ff Briefly tap or . stations. The update takes time,

ff Press and hold the or button. which is why not all FM stations are
ff Turn the control knob : clockwise or necessarily immediately available if
anticlockwise. the reception area suddenly changes.

FM station list Storing a station

All the receivable FM radio stations in the Six radio stations in each frequency band (AM,
current reception area are listed in the FM FM1 and FM2) can be stored using the station
station list. preset buttons.
ff Tap on List. ff Select the desired frequency band.
The available FM stations are displayed. The ff Tune into the desired station or select the
FM station that is currently playing is high- station from the FM station list.
lighted. ff Press and hold down one of the station
preset buttons 1 - 6 < until you hear a
beep.
The corresponding number of the station
preset button (e.g. P1) appears next to the
name of the frequency band in the top line of
the menu (see the screenshot below). The
station that is currently being played is stored.
You can recall the station from the station
presets memory by pressing the station preset
Furthermore, it is possible to play one of the button <.
FM stations that is stored in memory. If a
station is stored on one of the station buttons
1 - 6 <, the name of the frequency band and
the number of the station preset button is
displayed in the list.
ff Select the FM station that you want to
play.

Note
The system’s dual receiver continuo- Note
usly updates the FM station list in the If you do not hear a beep when
background. This ensures that on storing the station, the system
long journeys the station list always sounds may be deactivated. For
contains the locally available FM details on activating the system

01_DAF_MMT_en.indd 17 25.01.13 12:00

 18 Radio | Media

sounds, please refer to the “Introduc- Media

tion” chapter, “Adjusting settings”
section. CD player

Accessing a station General information

ff Select the desired frequency band. The system can play audio CDs and MP3/WMA
ff Press one of the station preset buttons CDs.
<.
The corresponding radio station is played. Hazard for the device
ff To not use CDs with a diameter
of 8 cm or deformed CDs in the
CD player.
ff Never stick any adhesive labels
on the CDs. Such discs can get
stuck in the CD drive and
damage the drive. An expensive
replacement for the unit would
then be necessary.
ff Dirt or liquids on the CDs can
smear the lens of the drive in the
unit and cause disruption.

Important information about audio

CDs and MP3/WMA CDs
The following CD formats are supported:
ff CD
ff CD-R
ff CD-RW

The following file formats are supported:

ff ISO9660 Level 1, Level 2, (Romeo, Joliet)
ff Suitable playlist extensions: “.m3u”, “.
pls”, “.wpl”.
ff MP3 and WMA files recorded in a format
other the ones stated above may not be
played properly. Furthermore, the file

01_DAF_MMT_en.indd 18 25.01.13 12:00

 Media 19

names and folder names may not be Note

displayed correctly. WMA files can only be played reliably
ff Audio CDs with copy protection that do if they were created with Windows
not comply with the CD audio standard Media Player version 9. WMA files
may not play properly or at all. can also be played if they were
created using later versions of
Note Windows Media Player, but playback
CD-Rs and CD-RWs that you have is not guaranteed.
recorded yourself may not play
properly or at all. ff Entries in playlists must be entered as
relative paths.
ff Only the audio tracks will be played on
CDs that have mixed content (i.e. a Notes
combination of audio tracks and data, ff The chapter describes how to
such as MP3s). play MP3 files. WMA files are
ff Avoid leaving fingerprints when changing played in the same way. If you
CDs. insert a CD containing WMA
ff Put CDs back into their cases immediately files, the menus relating to MP3
after you have removed them from the are also displayed.
drive so as to protect them from damage ff In the CD player menus, you can
and dirt. only use the touch screen to
ff Never expose CDs to heat or direct select or activate the on-screen
sunlight. buttons.
ff WMA files with Digital Rights Management
(DRM) from online music stores cannot be Starting CD playback
played.
Hazard for the device
The following limits apply to data stored on an Do not try inserting a CD if there is
MP3/WMA CD: already a CD in the drive – this could
ff Maximum number of folders / playlists: damage the drive or CD.
200. If there is still a CD in the drive you
ff Maximum number of files / tracks: 800. can select CD mode by pressing the
ff The system supports a folder hierarchy of MEDIA button > (if necessary,
up to 8 folders deep. several times).
We accept no liability for any damage
to the CD drive or CD that may occur
as a result of inserting a further CD.

01_DAF_MMT_en.indd 19 25.01.13 12:00

 20 Media

ff Insert an audio CD or MP3/WMA CD with Stopping CD playback

its readable side facing down into the CD ff To stop playing an inserted CD, mute the
slot 2. unit by pressing the left control knob =.
The CD starts playing automatically and the CD ff To resume playing the CD, press the left
or CD-MP3 menu is displayed. control knob = again.

Selecting a track
During audio CD playback:
ff Tap on Browse to display a list of all the
tracks on the CD.
The track that is currently being played is
highlighted.
ff Select the desired track.

Note During MP3 CD playback:

If the inserted CD has already been ff Tap on Browse to display a list of all the
played before in the CD drive, the CD tracks in the currently selected folder.
will start playing from the track that The track that is currently being played is
was played last. highlighted.
ff To select another folder (if available) tap
ff If there is already a CD in the drive but the on Folder Up or press the button
corresponding menu is not displayed, ;.
press the MEDIA button > once or A list of all the folders on the CD is displayed.
several times. ff Select the desired folder.
ff Start CD playback. ff Select the desired track in the folder.
CD playback starts from the track that was
played last. Skipping to the next or previous
track
Depending on the data stored on the audio CD ff Press the or button @ once or
or MP3 CD, different information about the CD several times.
and the current music track may be displayed
on the screen. Fast forwarding or fast reversing
When normal CD playback mode is activated Press and hold the or button @ to
(i.e. no mix mode or repeat mode is activated), fast forward or fast reverse within the current
the CD starts playing from the first track even track.
after all the tracks on the CD have already been
played.

01_DAF_MMT_en.indd 20 25.01.13 12:00

 Media 21

Note Repeat mode

A beep will sound as soon as you have During audio CD playback:
activated fast forwarding or fast If repeat mode is activated, the current track is
reversing. If you do not hear a beep, played repeatedly until repeat mode is
the system sounds may be deactiva- deactivated again.
ted. For details on activating the ff Tap on Repeat to activate or deactivate
system sounds, please refer to the repeat mode.
“Introduction” chapter, “Adjusting When repeat mode is activated, “Repeat track”
settings” section. is shown in the display.

Mix mode When playing an MP3 CD:

During audio CD playback: If an MP3 CD is inserted, you can repeatedly
If you activate mix mode, all the tracks on an play the current track or all the tracks in the
audio CD will be played at random. currently selected folder until you deactivate
ff Tap on Mix to activate or deactivate mix repeat mode.
mode. ff Tap on Repeat once to activate track
When mix mode is activated, the “Mix” symbol repeat mode. If you tap on Repeat, you
appears in the display. can activate folder repeat mode or
deactivate repeat mode.
The currently activated mode (“Repeat track”
or “Repeat folder”) is shown in the display.

Ejecting a CD
ff Press the button 5.
The CD is ejected from the CD slot 2.

Note
During MP3 CD playback: If the CD is not removed after it is
If an MP3 CD is inserted, all the tracks in the ejected, the drive will draw it back
currently selected folder or all the tracks on the into the slot 2 automatically after a
CD can be played at random. few seconds.
ff Tap on Mix once to mix the current folder.
If you tap on Mix several times, you will USB port
activate the mix all mode.
The selected mode is shown in the display. General information
You can find out about the position of the USB
port in the vehicle documentation.

01_DAF_MMT_en.indd 21 25.01.13 12:00

 22 Media

Note played properly. Furthermore, their file

The socket must always be kept clean names and folders may not be displayed.
and dry.
The following limitations refer to data stored on
You can connect an MP3 player, USB storage external devices that are connected to the USB
device, SD card (via a USB adapter) or an iPod port:
to the USB port. ff Maximum number of folders/playlists:
If you connect the above devices to the USB 5000
port you can control them using the system’s ff Maximum number of files/tracks: 15000
controls and menus. ff Maximum number of files/tracks per
folder/playlist: 6000
Notes ff The unit supports a folder hierarchy of at
ff The system does not support all least 8 folders deep.
MP3 players, USB storage ff WMA files with Digital Rights Management
devices, SD cards, hard disk (DRM) from online music stores cannot be
drives or models of iPod. played.
ff The system is not compatible ff WMA files can only be played if they were
with the Apple iPad. created with Windows Media Player
version 9. Support for newer versions
Important information cannot be guaranteed.
ff The external devices connected to the ff Suitable playlist extensions: .m3u, .pls, .
USB port must comply with the USB mass wpl.
storage class (MSC) specification. ff The system supports bit rates of up to 320
ff Devices connected via USB are supported kbps at 48 kHz for MP3 and up to 192
according to the USB 2.0 specification. kbps for WMA.
The maximum supported speed is 12
Mbit/s. Playing audio files via USB
ff Devices that do not have the FAT16 / ff Connect, for instance, an MP3 player / a
FAT32 file system are not supported. USB storage device / a USB card reader to
ff Hard disk drives (HDD) are generally not the USB port using a USB cable.
supported. ff Press the MEDIA button > once or
ff USB hubs are not supported. several times to activate audio playback
for the USB source.
The following file formats can be used:
ff ISO9660 Level 1, Level 2, (Romeo, Joliet)
ff MP3 and WMA files in formats other than
those listed in this section may not be

01_DAF_MMT_en.indd 22 25.01.13 12:00

 Media 23

Note Bluetooth connection

USB audio sources are controlled in Bluetooth is a wireless standard for wirelessly
the same way as an audio MP3/WMA connecting devices, such as an MP3 player.
CD. To establish a Bluetooth connection with the
system, the Bluetooth function of the Blu-
Playing audio files from an iPod etooth device must be activated and the
ff Connect the iPod to the USB port. Bluetooth device must be set to “visible”
ff Press the MEDIA button > once or (discoverable mode).
several times to activate iPod mode. You will find further information on the settings
necessary on the Bluetooth device in the
Note: Bluetooth device’s manual.
An iPod connected via USB is Using the BLUETOOTH SETUP menu, you can
operated in the same way as has connect Bluetooth devices to the system (i.e.
been described for an audio MP3/ exchange PIN codes between the Bluetooth
WMA CD. device and the telephone interface).
Proceed as follows to open the BLUETOOTH
Bluetooth audio connection SETUP menu:
Bluetooth-capable audio sources that support ff Press the SETUP button 8.
the Bluetooth music protocol (A2DP) can be ff Tap on the Bluetooth menu item.
connected to the system.
Connecting a Bluetooth device
Important information Important information
ff The system only connects to Bluetooth ff A maximum of five devices can be paired
devices that support A2DP (Advanced with the system.
Audio Distribution Profile) Version 1.2. ff Only one paired device can be connected
ff The Bluetooth device must support to the system at any one time.
AVRCP (Audio Video Remote Control ff Usually the pairing procedure can only be
Profile) Version 1.0 or higher. If the device performed once unless the device was
does not support AVRCP, it will only be deleted from the list of paired devices.
possible to control the volume via the
system. Perform the following procedure to pair a
Bluetooth device with the system.
Note ff In the BLUETOOTH SETUP menu, set
Please inform yourself about this in Bluetooth to “On”.
the operating instructions for your ff Tap on Pair New Device.
Bluetooth device before you connect You will be asked to enter the PIN code “1234”
the Bluetooth device to the system. on the Bluetooth device.

01_DAF_MMT_en.indd 23 25.01.13 12:00

 24 Media

ff Activate the Bluetooth function on the ff Activate the Bluetooth function on the
Bluetooth device (if it is not already Bluetooth device if it is not already
activated). activated (refer to the operating instruc-
ff Activate “discovery mode” (please refer to tions of the Bluetooth device). A confirma-
the manual for the Bluetooth device). tion appears if the Bluetooth connection
The system’s Bluetooth name is “DAF TNR”. was established successfully.
ff Follow the instructions on the Bluetooth
device to establish the connection. If Notes
necessary, use the PIN code “1234” for ff If another Bluetooth device was
this. connected to the system prior to
A message is displayed if the pairing operation this, it will now be disconnected.
was successful. ff Only one Bluetooth device can
be connected to the system at a
Notes time, regardless of whether it is
ff If other Bluetooth devices were an audio streaming device, a
connected to the system prior to mobile phone or a multi-function
this, the device that was device (e.g. a mobile phone with
connected beforehand will be an integrated MP3 player).
disconnected. ff If the Bluetooth connection fails,
ff If the Bluetooth connection fails, carry out the pairing procedure
perform the procedure for again or refer to the Bluetooth
establishing a connection once device’s operating instructions.
more or refer to the Bluetooth
device’s manual. Deleting a paired device
ff In the BLUETOOTH SETUP menu, tap on
Connecting to another paired Delete Paired Device.
device A list of all the Bluetooth devices currently
ff In the BLUETOOTH SETUP menu, tap on paired with the system is displayed.
Select Paired Device.
A list of all the Bluetooth devices currently
paired with the system is displayed.
The Bluetooth device currently connected to
the system is indicated by the symbol.
ff Select the desired Bluetooth device.
The selected Bluetooth device is connected to
the system.

01_DAF_MMT_en.indd 24 25.01.13 12:00

 Media 25

ff Select the desired Bluetooth device. To pause or stop audio playback,

ff Tap on Yes to confirm the deletion. ff tap the button. To restart playback,
The device is removed from the list of paired tap again.
devices.
Note
Operation Activation of Bluetooth music mode
Requirements and controlling playback may be
The following requirements must be met in different depending on the Bluetooth
order to use the system’s Bluetooth music device.
mode:
ff The system’s Bluetooth function must be AUX connection
activated.
ff The Bluetooth function of the external General information
Bluetooth audio source must be activated You can connect external audio sources to the
(please refer to the device’s manual). AUX socket. Please refer to the vehicle’s
ff Depending on the external Bluetooth documentation to find the location of the AUX
audio source, it may be necessary to set connection.
the device to “visible” (please refer to the
device’s manual). Notes
ff The external Bluetooth audio source must ff Not all vehicles have an AUX
be paired with the system and connected connection.
to it. ff The AUX socket must always be
kept clean and dry.
Activating Bluetooth music mode ff You can, for instance, connect a
ff Press the MEDIA button > once or portable CD player to the AUX
several times to activate Bluetooth music input using a 3.5 mm plug.
mode.
The external audio source can now be operated Usage
via the system. ff Press the MEDIA button > once or
ff Tap on . several times to activate AUX mode.
Audio is played. The audio signal of the connected audio source
is now outputted on the system’s loudspea-
To play the next audio track, kers.
ff press the button @. The volume can be adjusted using the control
knob :.

01_DAF_MMT_en.indd 25 25.01.13 12:00

 26 Media | Navigation

Adjusting the input volume Navigation

Details on this are available in the “Introduc-
tion” chapter, in the “Volume settings” section. Road safety
The unit has been designed for use in
trucks.
Information about height restrictions
or maximum permitted road load,
which is required for navigating
trucks, is taken into consideration in
the route calculation insofar as this
information is stored in the navigation
data.
ff Please always pay attention
yourself to any restrictions on
the roads and in the road traffic
during your journey, also when
you are following the driving
recommendations provided by
the unit. The information stored
in the navigation data may be
incorrect, incomplete or
outdated.
ff To update the navigation data,
only use the latest navigation SD
cards that contain the informa-
tion relevant to trucks.
ff Make sure your vehicle’s
complete set of attributes and
the current load are stored at all
times in the unit in order to avoid
the calculation of unsuitable or
dangerous routes.

01_DAF_MMT_en.indd 26 25.01.13 12:00

 Navigation 27

General information computations in this case are less precise.

The system guides you reliably to your After you enter the destination address or a
destination, even if you are not familiar with location (e.g. the next fuel station, hotel, etc.),
the area. The system receives traffic reports in the system calculates the route from your
the current reception area via RDS-TMC. In current location to the selected destination.
order to provide dynamic navigation, the You are then navigated by spoken announce-
system uses traffic information available for ments and a directional arrow shown on the
the region when calculating a route. map.

Road safety TMC traffic information system and

Using the navigation system does not dynamic navigation
excuse the driver from driving and The TMC traffic information system receives
acting in a responsible and correct the latest traffic reports via the TMC radio
manner. You must always comply with stations. The TMC traffic information is
the applicable traffic regulations. If displayed in the map view as symbols or in the
the navigation instructions are not in TRAFFIC INFO menu as a text report.
keeping with the traffic regulations When the dynamic navigation system is
then the traffic regulations must activated, the traffic information is used to
always take priority. calculate the route. With this method, the
system plans the route in such a way that traffic
Note problems are avoided in accordance with
RDS-TMC is not available in all previously set criteria.
countries. If a traffic problem arises, a message is
displayed informing you that the route should
Navigation system functions be altered.
The orientation and motion of the vehicle is In order to use TMC traffic information, the
detected by sensors, and the distance traveled system must be able to receive the TMC
is determined using the vehicle’s mileage stations in the respective region.
counter. A sensor detects when the vehicle Dynamic navigation only works if the TMC
turns off a road, and the vehicle’s orientation is traffic information system receives traffic
identified using GPS satellites (Global reports.
Positioning System).
By comparing the sensor signals with the Map data
digital maps on the SD card, the system can The map data is stored on an SD card that is
determine the position with an accuracy of supplied with the system.
approx. 10 m. The system also works when
GPS reception is poor, though the position

01_DAF_MMT_en.indd 27 25.01.13 12:00

 28 Navigation

Note: ff Set the following vehicle attributes:

Please contact DAF Service for maps ff Height
of other regions. ff Width
ff Length
Vehicle attributes ff Actual weight
ff Gross weight
Road safety ff Axle load
Make sure before using the navigation ff No. of axles
system that the current vehicle ff Hazardous load
attributes have been entered/set in ff Trailer (yes, no)
the system.
The system takes the vehicle Road safety
attributes into consideration when The current navigation data does not
calculating the route so as to avoid support navigation that is compliant
unsuitable or dangerous route with hazardous loads.
sections. The settings you have set for
hazardous loads will not be taken into
You can store the attributes for different account when the route is calculated.
vehicle configurations (e.g. with and without a Make sure you always observe the
trailer or with and without a hazardous load) in traffic regulations that are in force
up to 4 different profiles. concerning this.
ff Press the SETUP button 8. It is expected that navigation data
ff Tap on Truck Attributes. that takes into account hazardous
loads in the route calculation will be
available from 2014 or 2015.

Note
You will also find the vehicle attri-
butes in the Navigation menu, in the
Options menu item.

Map options
ff Tap on Profile (if necessary, several To open the MAP OPTIONS menu,
times) to select or edit a profile. ff press the MAP button 4 and then tap on
Menu.
The following options are available.

01_DAF_MMT_en.indd 28 25.01.13 12:00

 Navigation 29

Show destination information

Select this option to display the address / GPS
coordinates of the next waypoint (if one exists)
on the route and/or the address / GPS
coordinates of the destination.
If the address / GPS coordinates of the next
waypoint is/are displayed, tap on Dest. to
display the address / GPS coordinates of the
destination.
Store current position If the address / GPS coordinates of the
The address / GPS coordinates of the current destination is/are displayed, tap on Waypt. to
position can be stored in the address book display the address / GPS coordinates of the
under any name you wish. next waypoint (if one exists). To store the
ff Select the menu item to open a menu that displayed address / GPS coordinates in the
contains a keyboard for entering the address book, tap on Save.
name.
ff Enter a name for the current position.
NAV button and NAVIGATION menu
Note ff Press the NAV button 6 to open the
To open a keyboard for entering NAVIGATION menu.
numbers and special characters, tap
on More. To delete characters, tap on
Delete.

ff Tap on OK to store the address / GPS

coordinates.
The position name is added to the address
book.

Show position information The NAVIGATION menu provides access to all

Select this option to display the address / GPS the system functions for entering a destination
coordinates of the current position. and for navigation.
To store the displayed address / GPS coordi-
nates in the address book, tap on Store. Entering a destination
ff Tap on Destination.
The following screen is displayed.

01_DAF_MMT_en.indd 29 25.01.13 12:00

 30 Navigation

1 Country name
2 Street/road name
3 House number
4 City/town name / postcode

ff Tap on Country.
ff Enter the desired country name.
ff Tap on City.
ff Enter the name or the postcode of the
Note destination town.
If the navigation function is active, ff Tap on Street.
you can enter a waypoint (a stopover) ff Enter the name of the destination
on the route to the current address.
destination. You can also replace the
set destination details with new Note
details. If you do not enter any characters for
the street name, you can skip the
Entering an address address input. Instead, tap on
ff Tap on Enter Address. Centre. The destination is then set
The ENTER ADDRESS menu is displayed. as the town center.
ff Enter the desired city/town name by
tapping on the letter keys. ff Enter the desired house number.

Note Note
The system automatically blocks all If you enter a house number that does
letters that cannot occur in the city not exist, the system offers the
name. If you need to enter a letter or following options:
special character, tap on More once ff No number: The house number
or several times until the desired is ignored. The destination is set
letter or special character is shown. to the middle of the destination
street.
Select one of the following input sequences: ff Get number from list: A list of
1 Country name available house numbers is
2 City/town name / postcode displayed. Select an option.
3 Street/road name
4 House number
or

01_DAF_MMT_en.indd 30 25.01.13 12:00

 Navigation 31

Note ff Position: Use this option to delete the

If you select the No number option, previous home address (if one exists) and
the CONFIRM DESTINATION menu save the current position as the new home
appears. If you select the Get address. The address details or GPS
number from list option, a list of coordinates of the current position are
available house numbers and/or displayed.
house number ranges is displayed. ff Change: Use this option to enter the
Select the list item with the desired address directly. The previous home
house number or house number address (if one exists) is deleted.
range. ff Start: Use this option to enter the
displayed home address or GPS coordi-
The CONFIRM DESTINATION menu displays a nates as the new destination and start
map view of the area surrounding the address navigation.
you have just entered. The new destination is
indicated by a checkered flag. Route
ff Press the NAV button 6 and then tap on
Adding a waypoint Route.
ff Press the NAV button 6 and tap on The following route list is displayed.
Destination or Previous Destinations.
ff Tap on Add waypoint.
ff Enter a waypoint or select one.

Home address
You can use this option to store your own
address and/or select the already stored home
address as a new destination.

Entering and selecting the home address The route list displays all the roads on the
ff Press the NAV button 6 and then tap on calculated route, starting with your current
Home. position.
The current home address or GPS coordinates The following information can be displayed in
are displayed. each list:
ff Name of the road, motorway or motor
The following menu options are available: junction
ff Directional arrow or motorway symbol

01_DAF_MMT_en.indd 31 25.01.13 12:00

 32 Navigation

Note Previous destinations

The red triangle in a directional arrow Use this option to display a list of destinations
or motorway symbol indicates that that you have used before for navigation. You
there is a traffic holdup on the can select an item from this list and set it as
selected road or motorway. your new destination.

ff Distance to the next road on the route Selecting a previous destination

ff Estimated time until the next road on the ff Press the NAV button 6.
route is reached ff Tap on Previous Destinations.
ff Estimated arrival time when the next road The list of previous navigation destinations is
on the route is reached displayed.
Depending on the time format that has been
activated for the map view, the estimated
remaining journey time or the estimated arrival
time will be displayed.

Note
If no home address was set up
beforehand, the address field in the
menu will remain empty.
Note
Changing the time display mode Up to 50 previous destinations are
ff Press the MAP button 4. stored automatically. When the
The following screen is displayed. system attempts to save more than
50 destinations, the oldest is
automatically deleted from the list
and the newest is added.

ff Select the previous destination.

The following menu options are available:
ff Save: Tap on this option to store the
displayed destination data in the address
book.
ff Tap on the time information in the display ff Del. all: Tap on this option to delete the
beneath the directional arrow. entire list of previous destinations.
ff Delete: Tap on this option to delete the
displayed destination from the list of

01_DAF_MMT_en.indd 32 25.01.13 12:00

 Navigation 33

previous destinations. ff Route mode: Select one of the options –

ff OK: Use this option to enter the displayed Fastest, Eco or Shortest route – for
address or GPS coordinates as the new navigation.
destination and start navigation to this ff Motorways: Select whether motorways
destination. should be used for navigation or avoided.
ff Tolls & Ferries: Select whether toll roads
Options and ferries should be used in the
Use these options to modify the settings for calculation of the route to the destination
the route calculation/recalculation and the or whether they should be avoided.
navigation function.
ff Press the NAV button 6. Stopping route guidance
ff Tap on Options. Use this option to cancel the current route
The ROUTE OPTIONS menu is displayed. guidance.
If there is an additional waypoint present for
the current navigation session, you may
receive the following query:
ff Cancel navigation to the waypoint and to
the ultimate destination?
ff Cancel only navigation to the waypoint?

Note
If you only want to cancel navigation
The following menu options are available: to the waypoint, the navigation
ff Dynamic navigation: You can set all the system will recalculate the route
options. automatically in order to guide you to
ff Off: Use this option to deactivate your ultimate destination.
route calculation/recalculation on the
basis of TMC. TRAFFIC INFO menu
ff Automatic: Use this option to activate ff Press the TRAF button 7 to open the
route calculation/recalculation on the TRAFFIC INFO menu.
basis of TMC. When the navigation system is activated, the
ff Prompt: Use this option to allow or TRAFFIC INFO menu displays all the traffic
disallow route calculation/recalcula- incidents on the current route and/or in the
tion only after the system prompts surrounding area.
you.

01_DAF_MMT_en.indd 33 25.01.13 12:00

 34 Navigation

Block consecutive roads from the current route.

Use this menu to exclude selected roads in a ff To exclude a road, select the desired road.
route section from the navigation. To exclude several consecutive roads,
ff In the TRAFFIC INFO menu, tap on Block. select the first and last road of the route
The AVOID ROUTE SECTION menu is displa- section you want to exclude.
yed. ff Tap on Recalculate Route.
The route is recalculated.

Note
You can only select a single road or a
section of the route at a time for
exclusion from the route list.

ff Use Road Ahead: Use this option to undo

the exclusion of a section of route.
The following menu options are available: ff Use Road In Route List: Use this option
ff Avoid Road Ahead: Using this option, to undo the exclusion of the roads from
you can exclude a section of the route by the route list.
specifying the length of section to be
omitted starting from the current position TA
of the vehicle. Use this option to activate or deactivate
priority for traffic announcements.

Route
Use this option to display a list of all traffic
incidents on the current route. To obtain more
detailed information about a specific traffic
incident, select an item from the list.

All
ff To omit roads, tap the / buttons Use this option to display all the traffic
to adjust the “Avoid Dist.” settings. incidents on the current route. In addition, you
ff Tap on Recalculate Route. can also display all the traffic incidents in the
The route is recalculated. area around the current vehicle position.

ff Avoid Road In Route List : Use this

option to exclude a single road or several

01_DAF_MMT_en.indd 34 25.01.13 12:00

 Navigation 35

SETUP button and NAVIGATION north) and “Head” mode (map

menu aligned with your heading).
ff Press the SETUP button 8 to open the ff Auto Zoom: If you set this option,
SETUP menu. the map scale is automatically
ff Tap on Navigation. adjusted by the navigation system
The NAVIGATION SETUP menu is displayed. (zoomed in and out).
ff Show POIs In Map: If you set this
Note option, points of interest, such as fuel
Alternatively, you can also use the stations, car parks or restaurants, are
following method to open the “Map displayed on the map with the
Setup” menu. relevant symbol.
ff Press the MAP button 4. ff Map Data Information: Use this
ff Tap on Menu. option to display the name and
ff Select Map Setup. version of the map data stored on the
SD card.
The NAVIGATION SETUP menu provides ff Voice Guidance: If you set this option,
various settings for customizing the navigation spoken announcements are made during
system. navigation.
ff Voice Vol.: If voice guidance is activated,
The following settings/options are available: this setting changes the volume of the
ff Map Setup: The following settings/ spoken announcements. An audio
options are available in Map Setup: example is played after each adjustment.
ff Map view: Use this option to switch ff Position Information: Use this option to
between the two dimensional, flat display the address / GPS coordinates of
map view (2D) and the three the current position. To store the
dimensional, perspective view (3D). displayed address / GPS coordinates in
the address book, tap on “Store”.
Note: ff Time Display: Use this option to switch
In the 2D map view you can switch between displaying the estimated arrival
between the “North” and “Head” map time and the estimated remaining journey
orientation modes. Only the “Head” time. Details on this are available in the
orientation mode is available in 3D “Information in the map view” chapter.
mode. ff Distance Units: With this option you can
switch between displaying distances in
ff Map orientation: Use this option in miles and kilometers.
2D map view to switch between ff POI Warning: This option is available if
“North” mode (map aligned with user-defined points of interest with the

01_DAF_MMT_en.indd 35 25.01.13 12:00

 36 Navigation

corresponding warning notices have been user-defined points of interest”

downloaded onto the system. If this chapter.
option is activated, a warning notice is
displayed when the vehicle approaches a ff Remove User POIs From System: This
location that has been defined by the option is only available if user-defined
user. points of interest have been downloaded
onto the system.
Note ff Demo Mode: If demo mode is activated,
Further details on this are available in you can simulate route guidance while the
the “User-defined points of interest” vehicle is stationary. You can use this
chapter. function to familiarize yourself with the
navigation system.
ff POI Warning Distance: This option is ff Set Start Location For Demo: Enter an
only available if user-defined points of address as the starting point for the
interest and the corresponding warning simulated route guidance.
notices have been downloaded onto the
system. You can use this option to define
the threshold value at which the system
issues a warning before you reach a
particular user-defined location. To set
the threshold value, proceed as follows:

ff Tap on POI Warning Distance:

A list of distances for the point of interest
warning is displayed.
ff Select the desired point of interest
warning.
ff Download my POIs now: This option is
only available if a USB storage device on
which user-defined points of interest are
stored is connected to the system.

Note
Details on this are available in the
“User-defined points of interest”
chapter and the “Downloading the

01_DAF_MMT_en.indd 36 25.01.13 12:00

 Navigation 37

Information in the map view

ff To display the map for your current position press the MAP button 4.
A B C D E

F
P

O
G

N H

M L K

Symbol Status
The following information is displayed when
route guidance is activated: Truck-specific information
about the road is available;
A Selected audio source the road is not suitable for
B Details about what is currently playing the currently set vehicle
(e.g. the current frequency in radio attributes!
mode).
C Status of the current road for your vehicle. No truck-specific informa-
tion about the road is
Symbol Status available!
Truck-specific information D Name of the road after the next driving
about the road is available; maneuver.
the road is suitable for the
currently set vehicle E Current time
attributes.

01_DAF_MMT_en.indd 37 25.01.13 12:00

 38 Navigation

F A compass indicates north. K The currently selected map scale.

Note Notes
In the two-dimensional map view, tap ff To adjust the scale, turn the
on the compass to switch between control knob :.
the “North” orientation and “Head” ff If auto zoom mode is activated,
orientation map view modes. the map scale is automatically
adjusted by the navigation
G Route system (zoomed in / out).

Notes L The road name for the current position.

ff The ultimate destination is M Button to open the map options menu.
indicated by a black checkered N Estimated arrival time or remaining
flag. journey time as well as the remaining
ff A waypoint is indicated by a red distance to the destination.
checkered flag.
ff Traffic incidents, such as traffic Notes
jams, are indicated by their ff Tap on the time display to switch
corresponding symbols and by a between the arrival time and the
route section marked in black on remaining journey time.
the map. ff The time calculations are based
ff Traffic incidents are only on average speeds specific to
displayed on the map when automobiles or specific to trucks
dynamic navigation is activated. (if a profile is selected in the
TRUCK ATTRIBUTES menu).
H Points of interest, such as fuel stations,
car parks and restaurants, are indicated O The directional arrow and the distance to
by the corresponding symbols. the next maneuver.
P Button for voice guidance.
Note
The option to display points of Note
interest can be activated and Tap on Voice to repeat the last
deactivated. spoken announcement.
Touch Voice for a few seconds to
J The vehicle’s current position. activate or deactivate voice guidance.

01_DAF_MMT_en.indd 38 25.01.13 12:00

 Navigation 39

User-defined points of interest -- Name of the location

In addition to the points of interest stored on (e.g. 9.9800000,52.0150000,“David’s
the SD card, you can also define your own Apartment”)
points of interest. You can download the points
of interest you created onto the system. Notes
You can create the following: ff The data must be entered on one
ff Destination locations line.
ff Points of interest warnings ff You can obtain the necessary
GPS coordinates from, for
Your own points of interest: example, a topographic map.
These are points of interest that you can use as ff The GPS coordinates must be
destinations for the navigation system. You entered in degrees using the
should define the GPS coordinates (longitude decimal system.
and latitude) for each location and enter a ff Coordinates with a western
descriptive name. After you have downloaded longitude and a southern latitude
the points of interest data onto the system, must be entered with a leading
select a name (e.g. “David’s Apartment”) from minus sign “-”.
the menu of user-defined points of interest that
can be used as a destination for the navigation ff Enter longitude and latitude coordinates
system. into the text file separated by a comma.
To create points of interest, proceed as follows: ff Give the location any name you wish.

Note Note
You must create a separate ASCII- The name must be placed inside
coded text file for each point of inverted commas and separated from
interest type in a simple text editor the GPS coordinates by a comma.
application.
ff Enter each additional point of interest
ff Create a text file that has the file extension destination on a new line in the text file.
.asc and give it any name you like (e.g. ff Save the text file (e.g. on the hard drive of
“SamsLocations.asc”). your PC or notebook).
ff Enter the following data for the
destination into the text file: Points of interest warnings
-- Longitude coordinates You can create warning notices that should be
-- Latitude coordinates issued before you reach a certain location (e.g.
sharp bends on the road). When the vehicle
reaches the location defined by the GPS

01_DAF_MMT_en.indd 39 25.01.13 12:00

 40 Navigation

coordinates, the corresponding warning notice Note

is displayed (e.g. “Sharp bends”). The name must be placed inside
inverted commas and separated from
To create the points of interest warning, the GPS coordinates by a comma.
proceed as follows:
ff Create a separate text file that has the file ff Enter each additional point of interest
extension .asc and give it any name you destination on a new line in the text file.
like (e.g. “PoorRoads.asc”). ff Save the text file (e.g. on the hard drive of
ff Enter the following data for the your PC or notebook).
destination into the text file:
-- Longitude coordinates Storing text files on a USB storage device
-- Latitude coordinates ff In the root directory of a USB storage
-- Name of the location device, create a folder with the name
(e.g. 7.6800000,49.0120000,“Poor- “myPOIs” (e.g. “L:\myPOIs”, where “L:\” is
Road”) the root directory of the USB storage
device).
Notes ff Store the text file containing the
ff The data must be entered on one destination locations in the “myPOIs”
line. folder.
ff You can obtain the necessary ff Create a subfolder called “myPOIWar-
GPS coordinates from, for nings” inside the “myPOIs” folder.
example, a topographic map. ff Store the text file containing the point of
ff The GPS coordinates must be interest warnings in this subfolder. (e.g.
entered in degrees using the „L:\myPOIs\myPOIWarnings\PointOfIn-
decimal system. terestWarnings.asc“).
ff Coordinates with a western
longitude and a southern latitude Downloading the user-defined points of
must be entered with a leading interest
minus sign “-”. ff Plug the USB storage device containing
your point of interest data into the
ff Enter longitude and latitude coordinates system’s USB port.
into the text file separated by a comma. ff To start the download, press the SETUP
ff Give the location any name you wish. button 8.
ff Tap on Navigation.
ff Tap on Download my POIs now.
The points of interest data are downloaded
onto the system.

01_DAF_MMT_en.indd 40 25.01.13 12:00

 Navigation 41

Maps ff Do not expose the SD card to direct

The map data required for navigation is stored sunlight, high temperatures or moisture.
on an SD card that is supplied with the system. ff When the SD card is outside the device,
always keep it in a protective case to
Navigation SD card protect it against dirt, moisture and
The system’s SD card reader can only read SD mechanical forces.
cards that are supplied specifically for use with
vehicle navigation systems. The SD card reader Note
cannot read any other SD cards. You can obtain map updates from
The map data on the SD card is sometimes not your vehicle dealer.
completely up to date – some roads are not
included or names and roads differ from those Changing a navigation SD card
that were in use at the time the map was
produced. You can order new navigation SD Hazard for the device
cards to obtain the latest map data. Do not use force to open the cover of
the SD card slot.
Hazard for the device
Do not use any SD card that is
cracked or deformed or has been Note
repaired with adhesive tape. If you remove the SD card while route
Damaged SD cards can damage the guidance is active, the route guidance
system. session will be canceled.

ff Handle the SD card with care. In particu- ff Pull the right hand side of the cover of the
lar, make sure you do not touch or dirty SD card slot 9 out of the front of the unit
the contacts. and swing it to the left.
ff Do not use any conventional cleaners, ff Press down on the inserted SD card to
benzine, thinner or antistatic sprays to unlatch it. Carefully pull the SD card out of
clean the SD card or its contacts. the slot.
ff Do not subject the SD card to mechanical ff Carefully slide the new SD card with its
forces, such as bending or compression. labeled side facing up and with the cut-out
Do not use any warped or broken SD sections on the right into the SD card slot
cards. 9.
ff Do not stick any adhesive labels on the SD ff Close the cover of the SD card slot.
card to ensure the SD card can be You have successfully changed the SD card.
inserted in and removed from the card
slot without problems.

01_DAF_MMT_en.indd 41 25.01.13 12:00

 42 Steering wheel remote control | Technical data

Steering wheel remote Technical data

control
You can operate the radio/navigation unit using Operating voltage: 12 V (10.8 V – 15.6 V)
the buttons on the steering wheel.
Current consumption
Functions of the steering wheel During operation: 1.3 A
remote control Max.: approx. 8.0 A
button Standby: 1 mA
Switch between radio, CD/MP3, CD changer
and external audio/video source. Fuse
Current rating: 10 A
button
Decrease the volume. Outputs
Rated power output: 4 x 20 W / ≥ 4 ohms
button Output level (operating voltage = 14.4 V):
Increase the volume. ≥ 8.0 V / THD = 2.5%

button Operating temperature:

ff Radio: Automatic station seek tuning. -20 ˚C to +70 ˚C
ff CD/MP3 and CD changer: Select the Storing temperature: -40 ˚C to +85 ˚C
previous track or restart the current track
(short press); fast reverse searching (long Frequency response (±3 dB)
press). CD/MP3: 20 Hz to 20 kHz
Tuner: 35 Hz to 16 kHz
button
ff Radio: Automatic station seek tuning. Frequency ranges
ff CD/MP3 and CD changer: Select the next FM (VHF): 87.5 - 108 MHz
track (short press) - fast forward AM: 531 - 1602 kHz
searching (long press).
Weight: approx. 1.8 kg

Dimensions WxHxD (in mm)

187.2 x 118.6 x 216.9

Standards: CE, E1, RoHS, WEEE

Subject to changes.

01_DAF_MMT_en.indd 42 25.01.13 12:00

 43

01_DAF_MMT_en.indd 43 25.01.13 12:00

 DW53205501
Printed in the Netherlands
Copy deadline: 09.2012

02_DAF_MMT_en_Rueck.indd 48 24.01.13 19:48