RAYMING PCB & ASSEMBLY
An Introduction to 2 Layer PCB
Table of Contents
What is a double sided PCB?
The 2 layer PCB ( double-sided PCB )is a printed circuit board with copper
coated on both sides, top and bottom. There is an insulating layer in the
middle, which is a commonly used printed circuit board. Both sides can be
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
layout and soldered, which greatly reduces the difficulty of layout, so it is
widely used.
To use circuits on both sides, there must be a proper circuit connection
between the two sides, as shown in the pictures below. The “bridges”
between such circuits are called vias. A via is a small hole on the PCB
board filled or coated with metal, which can be connected with the circuits
on both sides. Because the area of the double-sided board is twice as
large as that of the single-sided board, the double-sided board solves the
difficulty of the single-sided board due to the interlaced layout (it can be
connected to the other side through the holes), and it is more suitable for
more complicated circuits than the single-sided board.
We need electronic products with high performance, small size, and
multiple functions, which promotes the development of printed circuit
board manufacturing to be light, thin, short, and small. With limited
space, more functions can be realized, layout density has become greater,
and the hole diameter is smaller. The minimum hole diameter of
mechanical drilling capacity has dropped from 0.4mm to 0.2mm or even
smaller. The hole diameter of the PTH is getting smaller and smaller. The
quality of the PTH (Plated Through Hole) on which the layer-to-layer
interconnection depends is directly related to the reliability of the printed
circuit board.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
Request Doubld Sided PCB Manufacturing Quote Now
Double Layer PCB Production Manufacturing process
The production of double-sided board is more complicated than
single-sided board. The main reasons are as follows:
(1) The top and bottom layers of the copper coated board/laminate must
be layout
(2) The circuits on the top and bottom layers should be connected with
PTH.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
Particularly critical among these is the PTH, which is also the core process
of double-sided board production. The so-called PTH is created
by coating/plating a layer of metal on the inner wall of the via to connect
the printed circuits of the top and bottom layers. At present, domestic PTH
mainly adopts the electroless copper plating process in China. There are
two types of electroless copper plating process:
① The thin copper is electrolessly plated first, then the whole board is
electroplated to thicken the copper layer, and finally the pattern transfer is
performed.
② The thick copper is electrolessly plated first, and then the
pattern is transferred directly.
Both of these processes are widely adopted. However, the electroless
copper plating method is harmful to the environment, and it will gradually
be replaced by more advanced Black hole technology, tin/palladium direct
plating technology, and polymer direct plating technology.
2 Layer PCB With HASL-LF /immersion gold surface production
process
Cutting —> Drilling —> Sinking/1ST Copper Plating —> Layout —> Pattern
Plating/2nd Copper Plating —> Etching —> Solder Mask —> Legend
Printing —>Immersion Tin (or Immersion Gold) —> CNC Routing —> V
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
Cut (some boards do not need this) —> Flying Probe Test —> Vacuum
Packaging
Double-sided PCB with gold plating production process
Cutting —> Drilling —> 1ST Copper Plating —> Layout —> Pattern
Plating/2nd Copper Plating —> Gold and Nickel Plating —> Etching —>
Solder Mask —> Legend Printing —> CNC Routing —> V Cut —> Flying
Probe Test —> Vacuum Packaging
Multilayer HASL-LF board/immersion gold board production
process
Cutting —> Inner Layer —> Layer Stack —> Drilling —> Sinking/1ST Copper
Plating —> Layout —> 2nd Copper Plating —> Etching —> Solder Mask —>
Legend Printing —> Immersion Tin (or Immersion Gold) —> CNC
Routing —> V Cut (some boards do not need this) —> Flying Probe
Test —> Vacuum Packaging
Multilayer plate gold plate production process
Cutting —> Inner Layer —> Layer Stack —> Drilling —> Sinking/1STCopper
Plating —> Layout —> 2ndCopper Plating —> Gold and Nickel
Plating —> Etching —> Solder Mask —> Legend Printing —> CNC
Routing —> V Cut —> Flying Probe Test —> Vacuum Packaging
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
1. Pattern plating process
Copper clad board/Laminate —> Cutting —> Punching and drilling
benchmark —> CNC drilling —> Inspection —> Deburring —> Electroless
thin copper plating —> Electroplating thin copper —> Inspection —>
Brushing —> Filming —> Exposure and development (or curing) —>
Inspection and repairing —> Pattern plating (Cn + Sn/Pb) —> Film
removal —> Etching —> Inspection and repair board —> Nickel-plated and
gold-plated plugs —> Hot melt cleaning —> Electrical continuity
detection —> Cleaning —> Solder mask —> Curing —> Legend —>
Curing —> Shape processing —> Washing and drying —> Inspection —>
Packaging —> Finished product.
Thin copper —> Thin copper electroplating —> Electroplating thin copper
can be replaced by a single process of electroless thick copper
plating; both have their advantages and disadvantages.
The pattern plating —> etching method of double-sided board was typical
in the 1960s and 1970s. The process of Solder Mask on Bare
Copper (SMOBC) gradually developed in the 1980s, and has become the
mainstream process especially in precision double-sided board
manufacturing.
1. SMOBC process
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
The main advantage of SMOBC board is that it solves the short-circuit
phenomenon of solder bridging between thin circuits. At the same time,
due to the constant ratio of lead and tin, it has better solderability and
storage properties than hot melt board.
There are many ways to manufacture SMOBC boards, including the
SMOBC process of standard pattern electroplating subtraction and then
lead-tin stripping; the subtractive pattern electroplating SMOBC process of
using tin plating or immersion tin instead of electroplating lead-tin; the
plugging or masking hole SMOBC process; additive method SMOBC
technology; etc. The following mainly introduces the SMOBC process and
the plugging method SMOBC process flow of the pattern electroplating
method and then the lead-tin stripping.
The SMOBC process of pattern plating followed by lead-tin removal is
similar to the pattern plating process, and changes only after etching.
Double-sided copper laminate —> According to the pattern electroplating
process to the etching process —> Lead and tin removal —>
Inspection —> Cleaning —> Solder mask —> Plug nickel plating and gold
plating —> Plug sticking tape —> Hot air leveling —> Cleaning —>
Legend —> Outline —> Cleaning and drying —> Finished product
inspection —> Packaging —> Finished product.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
Request 2 Layer PCB Manufacturing Quote Now
1. Main process flow of the plugging method
Double-sided copper laminate —> Drilling —> Electroless copper
plating —> Electroplating copper on the whole board —> Plugging
holes —> Film (positive film) —> Etching —> Removing screen printing
materials/Removing plugging material —> Cleaning —> Solder mask —>
Plug nickel plating and gold plating —> Plug sticking tape —> Hot air
leveling —> The following procedures are the same as above to the
finished product.
The steps of this process are relatively simple, and the key is to plug the
pores and clean the plugged solder mask.
In the hole plugging process, if the hole plugging solder mask is not used
to block the holes and the screen printing imaging, but is replaced by a
special masking dry film which is then exposed to make a positive image,
this is the masking hole process. Compared with the hole plugging
method, it fixes the problem of cleaning the solder mask in the hole, but it
has higher requirements for masking the dry film.
The basis of the SMOBC process is to first produce the bare copper double
layer board PTH, and then apply hot air leveling.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
Pore mechanism
Drill holes on the copper-clad board first. It then undergoes electroless
copper plating and electroplating copper to form plated through holes.
Both play a crucial role in hole metallization.
1. The mechanism of electroless copper
In the manufacturing process of double-sided and multi-layer printed
boards, it is necessary to metallize the non-conductive bare holes (NPTH),
that is, to implement electroless copper to make them a conductor. The
electroless copper precipitation solution is a catalytic “oxidation/reduction”
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
reaction system. Under the catalytic action of metal particles such as Ag,
Pb, Au, and Cu, copper is deposited.
1. The mechanism of copper electroplating
The definition of electroplating is to use a power source to push positively
charged metal ions in a solution to form a coating on the surface of
the cathode conductor. Copper electroplating is an “oxidation/reduction”
reaction. The copper metal anode in the solution oxidizes the copper
metal on its surface to become copper ions. On the other hand, a
reduction reaction occurs on the cathode, and copper ions are deposited
as copper metal. Both of them achieve the purpose of perforation through
chemical exchange, and the exchange effect directly affects the quality of
perforation.
Debris plug holes
In the long-term production control process, we found that when the hole
diameter reaches 0.15-0.3mm, the proportion of plug holes increases by
30%.
1. The plugging problem in the process of perforation
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
When the printed board is processed, most small holes of 0.15-0.3mm still
use the mechanical drilling process. In the long-term inspection, we found
that impurities remained in the hole when drilling.
The following are the main reasons for drilling plug holes:
When a plug hole appears in a small hole, due to the small hole’s diameter,
it is difficult to remove the impurities inside it by high-pressure water
washing and chemical cleaning before copper plating, which prevents the
exchange of the chemical solution in the hole during the electroless
copper precipitation process and makes the electroless copper lose its
effect.
When drilling holes, select suitable drill and backing plates according to
the thickness of the laminate, keep the substrate clean, and do not reuse
the backing plates. Effective dust collection (using an independent dust
collection control system) is a factor that must be considered to solve the
plugging hole.
Draw circuit diagram
1. There isa variety of dedicated PCB drawing software, such as Protel, etc.,
which can draw multilayer (including double-sided) circuit board diagrams.
The positions of the layers are aligned, and there are vias to connect the
layers.The circuit is connected to realize cross circuiting and facilitate
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
typesetting. After the layout is completed, it can be handed over to a
professional board factory to become a circuit board.
2. The double-sided circuit board should be drawn into the
circuit schematic diagram in turn, which can be divided into two steps.
Step 1: Draw the legends of the main components such as IC on the paper
according to the position of the circuit board, arrange and draw the circuit
of the pins and the peripheral components appropriately, and complete
the sketch. Step 2: Analyze the principle and organize the circuit
diagram according to the customary drawing method. You can also use
the circuit schematic software to arrange the components and connect
them, and then use its automatic typesetting function to organize.
The circuits on both sides of the board should be accurately aligned. You
can use the tips of tweezers, the light transmission of a flashlight, and
a multimeter to measure the connection and disconnection
and determine the connection and direction of the solder and circuits. If
necessary, remove the components to observe the layout.
Request 2 Layer PCB Manufacturing Quote Now
What is the difference between single-sided PCB and 2 layer
PCB ?
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
Single-sided and double-sided boards differ in the number of copper
layers. Double-sided has copper on both sides of the board, which can be
connected through vias. However, there is only one layer of copper on
one-sided board, which can only be used for layout, and the holes made
can only be used for SMT.
Single-sided board is the most basic PCB. The parts are concentrated on
one side, and the circuits are concentrated on the other side. Because the
circuits are only on one side, this kind of PCB is called single-sided.
Single-sided boards have many strict restrictions on the design of the
circuit (because there is only one side, the circuits cannot cross and must
follow separate paths), so only early circuits use this type of board.
There is layout on both sides of a double-sided circuit board, but to use
layout on both sides, there must be a proper circuit connection between
the two sides. The “bridge” between such circuits is called a via. A via is a
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
small hole filled or coated with metal on the PCB, which can be connected
with the layout on both sides. Because the area of the double-sided board
is twice as large as that of the single-sided board, it solves the difficulty of
the single-sided board due to the staggered layout (it can be passed to the
other side through vias), and is suitable for use in more complicated
circuits than single-sided board.
1. Raw Material
Single-sided board: Has copper foil only on one side, such as TV board.
Double-sided board: There are copper traces on both sides, connected
by conductive through holes. The price is generally 7 times different (not
fully defined due to different materials). There is also a kind of false
double-sided board in the industry, which has no through hole connection
(much lower cost).
1. Process
Single-sided PCB board: The solder joints are concentrated on one side,
and components are usually inserted on the other side. Some products
still have SMD components on the copper-clad side. Double-sided board:
Both sides can be layout, and both can have plug-in components
or SMD components.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
False double-sided PCB: Generally, only one side SMT and layout on the
other side. The double-sided copper cladding is connected by circuit on
both sides of the component foot.
1. PCB circuit board
Single-sided board: The metal circuit that provides the connection of the
parts is arranged on an insulating substrate material, which is also a
support carrier for installing the parts.
Double-sided PCB : When a single-sided circuit is not enough to provide
the connection requirements of electronic parts, the circuit can be
arranged on both sides of the substrate, and through hole circuits are
deployed to connect the circuits on both sides of the board.
1. Production process
Single-sided board: CAD or CAM CCL cutting, drilling positioning —>
Opening punching mold, making screen plate —> Printing conductive
pattern, curing —> Etching, removing printing material, cleaning —>
Printing solder mask pattern, curing —> Printing marking legends,
curing —> Drilling and punching positioning holes, punching and
blanking —> Circuit inspection, test —> Solder mask and OSP —>
Inspection, packaging, finished product.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
2 Layer PCB : AD and CAM CCL cutting/edging —> NC drilling —> PTH —>
Pattern plating —> Full plate plating —> Dry film or wet film method
masking or plugging holes —> (Negative pattern) (Positive pattern) —>
Copper plating/tin lead pattern transfer —> Film removal, etching —> Tin
and lead removal, plug plating removal, cleaning —> Printing solder
mask/legends —> Hot air leveling or OSP —> Routing/punching shape —>
Inspection/testing —> Packaging/finished products.
How do you make 2 layer PCB and precautions
At present, the mainstream circuit board assembly technology in the SMT
industry is “full-board reflow soldering (reflow)”. Of course, there are other
circuit board soldering methods, and this full-board reflow soldering can
be divided into single-sided reflow soldering and double-sided reflow.
Single-sided PCB reflow is rarely used now, because double-sided reflow
can save space on the circuit board, which means that the PCB can be
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
made smaller. For that reason, most of the boards seen on the market
now belong to the double-sided reflow process.
Because the “double-sided PCB reflow process” requires two reflows,
there will be some process restrictions. The most common problem is that
when the board goes to the second reflow, the parts on one side will be
falling due to gravity, especially when the board goes to the reflow zone
at high temperatures.
Generally speaking, smaller parts are recommended to be placed on the
first side to pass through the reflow oven, because the deformation of the
PCB will be smaller on the first pass through the reflow oven, and the
precision of solder paste printing will be higher, so it is more suitable to
use smaller parts.
Secondly, the smaller parts will not fall off the second time through the
reflow oven. Because the parts on the first side will be placed directly on
the bottom side of the circuit board, when the board re-enters the reflow
zone at high temperature, they are less likely to fall off the board due to
excessive weight.
Third, the parts on the first side must go through the reflow oven twice, so
their temperature resistance must be able to withstand the heat of the
oven twice. The general resistance capacitor is usually required to be able
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
to pass the high temperature at least three times. This meets the
requirement that some boards may need to go through the reflow again
for repair.
Which SMD parts should be placed on the second side through the reflow
furnace? This should be the focus.
Large components or heavier components should be placed on the
second side to pass through, to avoid the risk of parts falling into the
reflow furnace.
LGA and BGA parts should be placed on the second side through as much
as possible, so as to avoid unnecessary remelting risks during the second
pass, and to reduce the chance of empty/false soldering. If there are
smaller BGA parts, it is recommended to put them on the first side
through the reflow furnace.
Placing the BGA on the first or second side through the furnace has always
been controversial. Although placement on the second side can avoid the
risk of remelting the tin and affecting its quality, the PCB will usually
deform more seriously when the second side is passed through the reflow
furnace. If the PCB is severely deformed, it can be a big problem for the
delicate parts to be placed on the second side, because the solder paste
printing position and the amount of solder paste will become inaccurate.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
Therefore, the focus should be to think of a way to avoid PCB distortion,
instead of whether to put BGA on the first or second side.
Parts that cannot withstand overly high temperatures should be placed on
the second side through the reflow furnace. This is to prevent parts from
being damaged by high temperatures.
PIH/PIP parts should also be placed on the second side to pass through
the furnace. Unless the length of the solder pin does not exceed
the thickness of the board, the pin protruding from the PCB surface will
interfere with the steel plate on the second side, so that the solder paste
printed steel plate cannot be flatly attached to the PCB.
Some components may use soldering inside, such as a
network cable connector with LED lights. It is necessary to pay attention
to the temperature resistance of this part to pass the reflow oven twice. If
it fails, it must be placed on the second side.
When parts are placed on the second side, it means that the circuit board
has already been baptized by the high temperature of the reflow oven. At
this time, the circuit board has become somewhat warped and deformed,
which means that the tin quantity and printing position of the paste will
become more difficult to control, so it is easy to cause problems such as
empty soldering or short circuits. Therefore, it is recommended not to
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
place 0201 and fine-pitch parts on the second side through the furnace.
For BGA, try to choose a solder ball with a larger diameter.
In addition, in mass production, there are actually many process methods
for soldering and assembling electronic parts on the circuit board, but
each process is actually determined at the beginning of the circuit board
design, because the placement of the parts will directly affect the
soldering sequence and quality of the assembly, and the layout will be
indirectly affected.
Request Doubld Sided PCB Quote Now
Soldering method of double-sided circuit board
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
In order to ensure the reliable conduction effect of the double-sided
circuit board, the connection hole on the double-sided board (that is, the
PTH) should be soldered with a wire, and the protruding part of the
connection wire should be cut off to avoid stabbing the hand. This is
in preparation for the wiring of the board.
The essentials of double-sided circuit board soldering
1. Devices that require reshaping should be processed according to
the requirements of the process drawings:that is, reshaping first
and then SMT.
2. The diode should face up after shaping, and there should be no
discrepancyin the length of the two pins.
3. When inserting devices with polarity requirements, pay attention to
ensure that their polarity is notreversed. Roll integrated block
components after SMT. No matterwhether they are vertical or
horizontal parts, there must be no obvious tilt.
4. The power of the iron used for soldering must bebetween 25~40W.
The temperature of the soldering iron tip should be controlled at
about 242℃. If the temperature is too high, the tip is close to
useless,and the solder cannot be melted when the temperature is
low. The soldering time is controlled at 3~4 seconds.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
5. When soldering, generally follow the soldering principle of the
device from short to high and from the inside to the outside.
Thecorrectsoldering time must be mastered. If the time is too long,
the device, as well as the circuits on the copper clad board, will be
burnt.
6. Because the solderingis double-sided, a process frame for placing
the circuit board should also be made, so as not to squeeze the
components for the other side.
7. After the circuit board soldering is completed, a comprehensive
check should be carried out to find any missing insertion
orsoldering. After quality confirmation, trim the redundant device
pins of the circuit board, and then go to the next process.
8. In anyspecific operation, the relevant process standards should be
strictly followed to ensure the soldering quality of the product.
Re-soldering techniques for double-sided circuit boards
When re-soldering a double-sided circuit board, it is difficult to repair
because it is dirty, messy, and may have faults such as false soldering,
disconnection, and poor contact.
1. Observation: Based on drawings or prototypes, get a general
understanding of the physical layout.
PCB Manufacturing & Assembly Services https://www.raypcb.com/
RAYMING PCB & ASSEMBLY
2. Dismantling: Remove the soldered components, pins andflying
leads.
3. Cleaning: Use absolute alcohol to clean the rosin and soldering on
the surface of the circuit board. When cleaning, if you use a
soldering iron, it will be faster and the effect will be better.
4. Layout: Clarify the layout with reference to your observations. If
there is no picture, use the drawing method to assist in annotation.
5. Soldering: Solder according to the clarifiedcircuits. When
re-connecting circuit with circuit, try to arrange them on the back.
6. Inspection: According to the results of the drawing or prototype and
the analysis of the layout, check whether the soldering is correct
and reliable, and whether the process meets the requirements.
7. Power-on test.
Related Posts:
1. 28 Layer PCB: An Integrated Multi-Layer PCBs
2. High Quality 10 Layer PCB Manufacturing and Stack-up Guidelines
3. High Quality 20 Layer PCB Manufacturer
4. What is 3 layer PCB?
https://www.raypcb.com/double-sided-pcb-manufacturer/
PCB Manufacturing & Assembly Services https://www.raypcb.com/
