GRP INSTRUMENT ENCLOSURE

AND SUNSHADE

www.bulksrl.it | info@bulksrl.it
Company Introduction Pag. 1

MODEL 115G
Sunshade Pag. 4
External dimension in mm: 180/226 ( width) x 350 ( depth ) x 130 ( height )

MODEL 115N
Sunshade Pag. 5
External dimension in mm: 180/226 ( width) x 350 ( depth ) x 130 ( height )

MODEL 125G
Sunshade Pag. 6
External dimension in mm: 300/350 ( width) x 350 ( depth ) x 130 ( height )

MODEL 125N (ATEX)

Sunshade Pag. 7
External dimension in mm: 300/350 ( width) x 350 ( depth ) x 130 ( height )

MODEL 250G
Sunshade Pag. 8
External dimension in mm: 460 ( width) x 455( depth ) x 350 ( height )

MODEL 250N (ATEX)

Sunshade Pag. 9
External dimension in mm: 460 ( width) x 455( depth ) x 350 ( height )

MODEL 350G
Sunshade Pag. 10
External dimension in mm: 710 ( width) x 465( depth ) x 340 ( height )

MODEL 350N (ATEX)

Sunshade Pag. 11
External dimension in mm: 710 ( width) x 465( depth ) x 340 ( height )

MODEL 500G1
Enclosure without window Pag. 12
External dimension in mm: 710 ( width) x 465( depth ) x 340 ( height )

MODEL 500G2
Enclosure with window Pag. 13
External dimension in mm: 710 ( width) x 465( depth ) x 340 ( height )
MODEL 500N1
Enclosure without window Pag. 14
External dimension in mm: 710 ( width) x 465( depth ) x 340 ( height )

MODEL 500N2
Enclosure with window Pag. 15
External dimension in mm: 710 ( width) x 465( depth ) x 340 ( height )

MODEL 700G1
Enclosure without window Pag. 16
External dimension in mm: 710 ( width) x 395 ( depth ) x 495 ( height )

MODEL 700G2
Enclosure with window Pag. 17
External dimension in mm: 710 ( width) x 395 ( depth ) x 495 ( height )

MODEL 700N1
Enclosure without window Pag. 18
External dimension in mm: 710 ( width) x 395 ( depth ) x 495 ( height )

MODEL 700N2
Enclosure with window Pag. 19
External dimension in mm: 710 ( width) x 395 ( depth ) x 495 ( height )

SOFT ENCLOSURE Pag. 20

MOUNTING BRACKET Pag. 21

COOLING & HEATING Pag. 27

ACCESSORIES Pag. 28

CUSTOMIZED PRODUCT Pag. 31

CERTIFICATE & TEST Pag. 33

 Catalogue N° 01/19
Dimensions are for reference only, and are subject to change without notice.
All right reserved.
All dimensions are in millimeters.

tel. +39 02 66307514 | +39 02 66307430

fax +39 02 93664351 | www.bulksrl.it | info@bulksrl.it

Manufacturing unit & Warehouse: via Cimabue, 1/A 20032 Cormano (Mi) - Italy
The Company
The company, founded in 1999, boasts the experience of being active charter members
in the oil & gas market for two decades.
Located on the border of Milan in a modern facility ( owned by the company ), it serves
the international market exporting to over 50 countries worldwide through agents or

energy and petrochemical industries for its production of GRP instrument enclosure
and sunshade.

customers reliable products and services over time always updated with the latest
regulations.
Products are entirely manufactured in Italy.

Application
Modern industrial plants guarantee high performances, both in terms of produc-

pressure, temperature, etc.).

This is possible due to the constant monitoring of the processes through even more
sophisticated and reliable measurement instruments.

Pag 1 www.bulksrl.it
The malfunction or deterioration of such equipment, however, creates a series of
unexpected and costly consequences:

•
• Slowing or blocking the production due to incorrect alarm signal
• Early additional maintenance not budgeted and scheduled during programmed
turn-around.

The causes are multiple and

simultaneous:

• Low ambient temperature

• High humidity
• Direct exposure to sunlight
• Particularly aggressive
external atmosphere ( installa
tion next to the sea-coast,

• Sand storms
• Vandalism or accidents because
of unprotected or unsupervised
installation.

A practical and economical solution is

-
tion within BULK enclosures and/or
-
bre Reinforced Polyester).
Such protection ensures the mainte-
nance of the instrument in optimum
conditions, preserving performance
and measurement repeatability.

Product Features
Protection enclosures and sunshades are available in various sizes and are hot pressed

The self-extinguishing material is particularly suitable for aggressive and corrosive

environments, and is resistant to UV rays.
Light grey colouring is obtained by pigmentation of the polyester resin, and the
surfaces are therefore free from paint and/or maintenance operations.

areas is available according to the ATEX standard.

The protective housing is made of equal half-shells which close at 45° line with a
double sealing system to ensure a watertight IP 66 protection.
The rotating cover is hinged by means of a removable pin.
The lifting of the lid is accompanied by a locking device which keeps it open.
The closure is secured by two clasps, possibly lockable.

www.bulksrl.it Pag 2
All screws, hinges and clasps are made of
stainless steel.
On request, BULK can assemble the in-
struments and accessories inside the
enclosures to provide a product ready for
installation.

Technical notes on the hot

Reinforced Polyester )

Reinforced Polyester), is a type of rein-

today, this particular plastic has been

in the composite and in the processing

methods.
Today, it operates as a structural element
in the aircraft, shipbuilding, petrochemical
and automotive industries, to name only
the main ones.
Hot pressing method provides the

advantages compared to other types of

more economic productions (injection
moulding or manual laying): certainly in
the repeatability of the thicknesses and

mechanical properties which are unattainable with other production methods.

Thanks to its unique composition and production, hot moulded GRP guarantees:

• High resistance to a wide range of acids, solvents and chlorides

• Excellent heat resistance
• Thermal and electrical insulation
• Excellent weight/mechanical resistance
• No maintenance and absence of oxidation
• Ease of repair

Applications:
BULK GRP instrument enclosure and sunshades are used in the protection of the
following components:

•
• Electronic component (actuator, positioner, junction box, …)
•
• Actuator control panel
• Pump
Pag 3 www.bulksrl.it
Instrument Sunshade | Series SS
Instrument protection sunshade
made in hot pressed GRP Model: 115G

Technical Characteristics
• External dimension in mm: 180/226 ( width ) x 350
( depth ) x 130 ( height )
• Minimum thickness 3 mm
• Weight in kg: 0,6 ( without accessories )
• Light grey color similar to RAL 7032
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength

•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test report
43SL00177 )
• EAC CU TR 010/2011 compliance
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01 )
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01 )

Options/accessories:
• Antistatic material in according to ATEX: see model
115N
• External mounting bracket suitable for 2” pipe stand:
see section MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING
BRACKET
• Self standing mounting bracket: see section MOUNTING BRACKET
• 2” pipe stand: see section MOUNTING BRACKET
• TAG label: see section ACCESSORIES
•
• Custom design: see section CUSTOMIZED PRODUCT

www.bulksrl.it Pag 4 100%

Made in Italy
Instrument Sunshade | Series SSN
Instrument protection sunshade
made in hot pressed GRP Model: 115N
( ATEX 2014/34/UE certified )

Technical Characteristics
• External dimension in mm: 180/226 ( width ) x 350
( depth ) x 130 ( height )
• Minimum thickness 3 mm
• Weight in kg: 0,6 ( without accessories )
• Black color
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial environ-
ments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength

•
•
•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test
report 43SL00177 )
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01 )
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01 )

Options/accessories:
• External mounting bracket suitable for 2” pipe stand:
see section MOUNTING BRACKET
• Self standing mounting bracket: see section
MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING
BRACKET
• 2” pipe stand: see section MOUNTING BRACKET
• TAG label: see section ACCESSORIES
•
• Custom design: see section CUSTOMIZED PRODUCT

www.bulksrl.it Pag 5 100%

Made in Italy
Instrument Sunshade | Series SS
Instrument protection sunshade
made in hot pressed GRP Model: 125G

Technical Characteristics
• Instrument protection sunshade made in hot pressed

• External dimension in mm: 300/350 ( width ) x 350

( depth ) x 130 ( height )
• Minimum thickness 3 mm
• Weight in kg: 1,00 ( without accessories )
• Light grey color similar to RAL 7032
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons .
• High structural strength

•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1
( IMQ test report 43SL00177 )
• EAC CU TR 010/2011 compliance
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01)
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01)

Options/accessories:
• Antistatic material in according to ATEX: see model
125N
• External mounting bracket suitable for 2” pipe stand:
see section MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING
BRACKET
• Self standing mounting bracket: see section MOUNTING BRACKET
• 2” pipe stand: see section MOUNTING BRACKET
• TAG label: see section ACCESSORIES
•
• Custom design: see section CUSTOMIZED PRODUCT

www.bulksrl.it Pag 6 100%

Made in Italy
Instrument Sunshade | Series SSN
Instrument protection sunshade
made in hot pressed GRP Model: 125N
( ATEX 2014/34/UE certified )

Technical Characteristics
• External dimension in mm: 300/350 ( width ) x 350
( depth ) x 130 ( height )
• Minimum thickness 3 mm
• Weight in kg: 1,00 ( without accessories )
• Black color
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength

•
•
•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test
report 43SL00177 )
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01 )
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01 )

Options/accessories:
• External mounting bracket suitable for 2” pipe stand:
see section MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING
BRACKET
• Self standing mounting bracket: see section
MOUNTING BRACKET
• 2” pipe stand: see section MOUNTING BRACKET
• TAG label: see section ACCESSORIES
•
• Custom design: see section CUSTOMIZED PRODUCT

www.bulksrl.it Pag 7 100%

Made in Italy
Instrument Sunshade | Series SS
Instrument protection sunshade
made in hot pressed GRP Model: 250G

Technical Characteristics
• External dimension in mm: 460 ( width ) x 455( depth )
x 350 ( height )
• Minimum thickness 5 mm
• Weight in kg: 5,50 ( without accessories )
• Light grey color similar to RAL 7032
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength

•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test report
43SL00177 )
• EAC CU TR 010/2011 compliance
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01 )
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01 )
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx)

Options/accessories:
• Antistatic material in according to ATEX: see model
250N
• External mounting bracket suitable for 2” pipe stand:
see section MOUNTING BRACKET
• Internal mounting bracket: see section MOUNTING
BRACKET
• Wall mounting bracket: see section MOUNTING BRACKET
• 2” pipe stand: see section MOUNTING BRACKET
• TAG label: see section ACCESSORIES
•
• Custom design: see section CUSTOMIZED PRODUCT

www.bulksrl.it Pag 8 100%

Made in Italy
Instrument Sunshade | Series SSN
Instrument protection sunshade
made in hot pressed GRP Model: 250N
( ATEX 2014/34/UE certified )

Technical Characteristics
• External dimension in mm: 460 ( width ) x 455( depth )
x 350 ( height )
• Minimum thickness 5 mm
• Weight in kg: 5,50 ( without accessories )
• Black color
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength

•
•
•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test
report 43SL00177 )
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01)
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01)
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx)

Options/accessories:
• External mounting bracket suitable for 2” pipe stand:
see section MOUNTING BRACKET
• Internal mounting bracket: see section MOUNTING
BRACKET
• Wall mounting bracket: see section MOUNTING
BRACKET
• 2” pipe stand: see section MOUNTING BRACKET
• TAG label: see section ACCESSORIES
•
• Custom design: see section CUSTOMIZED PRODUCT

www.bulksrl.it Pag 9 100%

Made in Italy
Instrument Sunshade | Series SS
Instrument protection sunshade
made in hot pressed GRP Model: 350G

Technical Characteristics
• External dimension in mm: 710 ( width ) x 465( depth )
x 340 ( height )
• Minimum thickness 5 mm
• Weight in kg: 7,50 ( without accessories )
• Light grey color similar to RAL 7032
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength

•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test report
43SL00177 )
• EAC CU TR 010/2011 compliance
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01 )
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01 )
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx)

Options/accessories:
• Antistatic material in according to ATEX: see model
350N
• External mounting bracket suitable for 2” pipe stand:
see section MOUNTING BRACKET
• Internal mounting bracket: see section MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING BRACKET
• 2” pipe stand: see section MOUNTING BRACKET
• TAG label: see section ACCESSORIES
•
• Custom design: see section CUSTOMIZED PRODUCT

www.bulksrl.it Pag 10 100%

Made in Italy
Instrument Sunshade | Series SSN
Instrument protection sunshade
made in hot pressed GRP Model: 350N
( ATEX 2014/34/UE certified )

Technical Characteristics
• External dimension in mm: 710 ( width ) x 465( depth )
x 340 ( height )
• Minimum thickness 5 mm
• Weight in kg: 7,50 ( without accessories )
• Black color
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength

•
•
•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test report
43SL00177 )
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01 )
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01 )
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx)

Options/accessories:
• External mounting bracket suitable for 2” pipe stand:
see section MOUNTING BRACKET
• Internal mounting bracket: see section MOUNTING
BRACKET
• Wall mounting bracket: see section MOUNTING BRACKET
• 2” pipe stand: see section MOUNTING BRACKET
• TAG label: see section ACCESSORIES
•
• Custom design: see section CUSTOMIZED PRODUCT

www.bulksrl.it Pag 11 100%

Made in Italy
Instrument Enclosure | Series IE
Instrument protection enclosure
made in hot pressed GRP Model: 500G1

Technical Characteristics
• External dimension in mm: 460 ( width ) x 410 ( depth )
x 490 ( height )
• Minimum thickness 5 mm
• Weight in kg: 7,50 ( without accessories )
• Hinges, clasps and lid propstay made in stainless steel
• Gasket made in EPDM
• Light grey color similar to RAL 7032
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength
• Resilient and mechanical double seal system

•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test report
43SL00177 )
• EAC CU TR 010/2011 compliance
• IP 66 construction ( NEMKO test report nr
189859-1TRFENV )
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01)
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01)
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx)

Options/accessories:
• Antistatic material in according to ATEX: see model
• 2” pipe stand: see section MOUNTING BRACKET
500N1
•
• Glass window: see model 500G2
• Custom design: see section CUSTOMIZED PRODUCT
• Gasket in silicone for temperature down to – 60°C:
• Insulation: see section COOLING & HEATING
specify model 501G1
• Heating: see section COOLING & HEATING
• External mounting bracket suitable for 2” pipe stand:
• Drain / vent valve: see section ACCESSORIES
see section MOUNTING BRACKET
• Through holes: see section ACCESSORIES
• Internal mounting bracket for instrument/manifold
• TAG label: see section ACCESSORIES
support: see section MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING BRACKET

www.bulksrl.it Pag 12 100%

Made in Italy
Instrument Enclosure | Series IE
Instrument protection enclosure
made in hot pressed GRP Model: 500G2

Technical Characteristics
• External dimension in mm: 460 ( width ) x 410 ( depth )
x 490 ( height )
• Minimum thickness 5 mm
• Weight in kg: 7,50 ( without accessories )
• Hinges, clasps and lid propstay made in stainless steel
• Gasket made in EPDM
• Window made in safety glass
• Light grey color similar to RAL 7032
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength

• Resilient and mechanical double seal system

•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test report
43SL00177 )
• EAC CU TR 010/2011 compliance
• IP 66 construction ( NEMKO test report nr
189859-1TRFENV )
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01)
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01)
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx)

Options/accessories:
• Antistatic material in according to ATEX: see model
•
500N2
• Custom design: see section CUSTOMIZED PRODUCT
• Without glass window: see model 500G1
• Insulation: see section COOLING & HEATING
• Gasket in silicone for temperature down to – 60°C:
• Heating: see section COOLING & HEATING
specify model 501G2
• Drain / vent valve: see section ACCESSORIES
• External mounting bracket suitable for 2” pipe stand:
• Through holes: see section ACCESSORIES
see section MOUNTING BRACKET
• TAG label: see section ACCESSORIES
• Internal mounting bracket for instrument/manifold
support: see section MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING
BRACKET
• 2” pipe stand: see section MOUNTING BRACKET

www.bulksrl.it Pag 13 100%

Made in Italy
Instrument Enclosure | Series IEN
Instrument protection enclosure
made in hot pressed GRP Model: 500N1
( ATEX 2014/34/UE certified )

Technical Characteristics
• External dimension in mm: 460 ( width ) x 410 ( depth )
x 490 ( height )
• Minimum thickness 5 mm
• Weight in kg: 7,50 ( without accessories )
• Hinges, clasps and lid propstay made in stainless steel
• Gasket made in EPDM
• Black color
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength
• Resilient and mechanical double seal system

•
•
•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test report
43SL00177 )
• IP 66 construction ( NEMKO test report nr
189859-1TRFENV )
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01)
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01)
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx)

Options/accessories:
• Glass window: see model 500N2
• Gasket in silicone for temperature down to – 60°C:
specify model 501N1
• External mounting bracket suitable for 2” pipe stand:
see section MOUNTING BRACKET for hazardous area
• Internal mounting bracket for instrument/manifold
support: see section MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING • Insulation: see section COOLING & HEATING
BRACKET • Heating: see section COOLING & HEATING
• 2” pipe stand: see section MOUNTING BRACKET • Drain / vent valve: see section ACCESSORIES
• • Through holes: see section ACCESSORIES
• Custom design: see section CUSTOMIZED PRODUCT • TAG label: see section ACCESSORIES

www.bulksrl.it Pag 14 100%

Made in Italy
Instrument Enclosure | Series IEN
Instrument protection enclosure
made in hot pressed GRP Model: 500N2
( ATEX 2014/34/UE certified )

Technical Characteristics
• External dimension in mm: 460 ( width ) x 410 ( depth )
x 490 ( height )
• Minimum thickness 5 mm
• Weight in kg: 7,50 ( without accessories )
• Hinges, clasps and lid propstay made in stainless steel
• Gasket made in EPDM
• Window made in safety glass
• Black color
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength
• Resilient and mechanical double seal system

•
•
• -
tuto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test report
43SL00177 )
• IP 66 construction ( NEMKO test report nr
189859-1TRFENV )
• Positively tested in wind tunnel up to 160 km/h ( Po-
litecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5 (
KIWA test report KIP-089534/01)
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01)
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx)

Options/accessories:
• Without glass window: see model 500N1
• Gasket in silicone for temperature down to – 60°C:
specify model 501N2
• External mounting bracket suitable for 2” pipe stand: for hazardous area
see section MOUNTING BRACKET
• Internal mounting bracket for instrument/manifold
support: see section MOUNTING BRACKET • Insulation: see section COOLING & HEATING
• Wall mounting bracket: see section MOUNTING • Heating: see section COOLING & HEATING
BRACKET • Drain / vent valve: see section ACCESSORIES
• 2” pipe stand: see section MOUNTING BRACKET • Through holes: see section ACCESSORIES
• • TAG label: see section ACCESSORIES
• Custom design: see section CUSTOMIZED PRODUCT • TAG label: see section ACCESSORIES

www.bulksrl.it Pag 15 100%

Made in Italy
Instrument Enclosure | Series IE
Instrument protection enclosure
made in hot pressed GRP Model: 700G1

Technical Characteristics
• External dimension in mm: 710 ( width ) x 395 ( depth )
x 495 ( height )
• Minimum thickness 5 mm
• Weight in kg: 10,00 ( without accessories )
• Hinges, clasps and lid propstay made in stainless steel
• Gasket made in EPDM
• Light grey color similar to RAL 7032
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength
• Resilient and mechanical double seal system

•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test report
43SL00177 )
• EAC CU TR 010/2011 compliance
• IP 66 construction ( NEMKO test report nr
189859-1TRFENV )
• Positively tested in wind tunnel up to 160 km/h
( Politecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01)
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01)
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx)

Options/accessories:
• Antistatic material in according to ATEX: see model •
700N1 • Custom design: see section CUSTOMIZED PRODUCT
• Glass window: see model 700G2 • Insulation: see section COOLING & HEATING
• Gasket in silicone for temperature down to – 60°C: • Heating: see section COOLING & HEATING
specify model 701G1 • Drain / vent valve: see section ACCESSORIES
• External mounting bracket suitable for 2” pipe stand: • Through holes: see section ACCESSORIES
see section MOUNTING BRACKET • TAG label: see section ACCESSORIES
• Internal mounting bracket for instrument/manifold
support: see section MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING BRACKET
• 2” pipe stand: see section MOUNTING BRACKET

www.bulksrl.it Pag 16 100%

Made in Italy
Instrument Enclosure | Series IE
Instrument protection enclosure
made in hot pressed GRP Model: 700G2

Technical Characteristics
• External dimension in mm: 710 ( width ) x 395 ( depth )
x 495 ( height )
• Minimum thickness 5 mm
• Weight in kg: 10,00 ( without accessories )
• Hinges, clasps and lid propstay made in stainless steel
• Gasket made in EPDM
• Window made in safety glass
• Light grey color similar to RAL 7032
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength
• Resilient and mechanical double seal system

• -
tuto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test re-
port 43SL00177 )
• EAC CU TR 010/2011 compliance
• IP 66 construction ( NEMKO test report nr
189859-1TRFENV )
• Positively tested in wind tunnel up to 160 km/h ( Po-
litecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01)
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01)
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx)

Options/accessories:
• Antistatic material in according to ATEX: see model • Custom design: see section CUSTOMIZED PRODUCT
700N2 • Insulation: see section COOLING & HEATING
• Without glass window: see model 700G1 • Heating: see section COOLING & HEATING
• Gasket in silicone for temperature down to – 60°C: • Drain / vent valve: see section ACCESSORIES
specify model 701G2 • Through holes: see section ACCESSORIES
• External mounting bracket suitable for 2” pipe stand: • TAG label: see section ACCESSORIES
see section MOUNTING BRACKET
• Internal mounting bracket for instrument/manifold
support: see section MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING BRACKET
• 2” pipe stand: see section MOUNTING BRACKET
•

www.bulksrl.it Pag 17 100%

Made in Italy
Instrument Enclosure | Series IEN
Instrument protection enclosure
made in hot pressed GRP Model: 700N1
( ATEX 2014/34/UE certified )

Technical Characteristics
• External dimension in mm: 710 ( width ) x 395 ( depth )
x 495 ( height )
• Minimum thickness 5 mm
• Weight in kg: 10,00 ( without accessories )
• Hinges, clasps and lid propstay made in stainless steel
• Gasket made in EPDM
• Black color
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength
• Resilient and mechanical double seal system

•
•
•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test report
43SL00177 )
• IP 66 construction ( NEMKO test report nr
189859-1TRFENV )
• Positively tested in wind tunnel up to 160 km/h ( Po-
litecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01)
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01)
-
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx)
hazardous area

Options/accessories:
• Glass window: see model 700N2
• Gasket in silicone for temperature down to – 60°C: • Insulation: see section COOLING & HEATING
specify model 701N1 • Heating: see section COOLING & HEATING
• External mounting bracket suitable for 2” pipe stand: • Drain / vent valve: see section ACCESSORIES
see section MOUNTING BRACKET • Through holes: see section ACCESSORIES
• Internal mounting bracket for instrument/manifold • TAG label: see section ACCESSORIES
support: see section MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING
BRACKET
• 2” pipe stand: see section MOUNTING BRACKET
•
• Custom design: see section CUSTOMIZED PRODUCT

www.bulksrl.it Pag 18
100%
Made in Italy
Instrument Enclosure | Series IEN
Instrument protection enclosure
made in hot pressed GRP Model: 700N2
( ATEX 2014/34/UE certified )

Technical Characteristics
• External dimension in mm: 710 ( width ) x 395 ( depth )
x 495 ( height )
• Minimum thickness 5 mm
• Weight in kg: 10,00 ( without accessories )
• Hinges, clasps and lid propstay made in stainless steel
• Gasket made in EPDM
• Window made in safety glass
• Black color
• Working temperature range: -40°C + 100°C
•
• Resistant to most corrosive types of industrial
environments, acids and alkalis
• Not absorption of hydrocarbons
• High structural strength
• Resilient and mechanical double seal system

•
•
•
( Istituto Giordano test report nr 311399 )
• UV resistant in according to ISO 179-1 ( IMQ test report
43SL00177 )
• IP 66 construction ( NEMKO test report nr
189859-1TRFENV )
• Positively tested in wind tunnel up to 160 km/h ( Po-
litecnico di Milano test report nr P48-07 )
• Positively tested Sand and dust Procedure II - Blowing
sand in according to MIL-STD-810G METHOD 510.5
( KIWA test report KIP-089534/01)
• Positively tested to Salt Mist Corrosion ( KIWA test
report KIP-090110/01) -
• IK 10 Impact protection, tested in accordance with
EN 62262:2002 ( NEMKO test report 305567-3&4 TRFEnvEx) hazardous area

Options/accessories:
• Without glass window: see model 700N1 • Insulation: see section COOLING & HEATING
• Gasket in silicone for temperature down to – 60°C: • Heating: see section COOLING & HEATING
specify model 701N2 Drain / vent valve: see section ACCESSORIES
• External mounting bracket suitable for 2” pipe stand: • Through holes: see section ACCESSORIES
see section MOUNTING BRACKET • TAG label: see section ACCESSORIES
• Internal mounting bracket for instrument/manifold • TAG label: see section ACCESSORIES
support: see section MOUNTING BRACKET
• Wall mounting bracket: see section MOUNTING
BRACKET
• 2” pipe stand: see section MOUNTING BRACKET
•
• Custom design: see section CUSTOMIZED PRODUCT

www.bulksrl.it Pag 19
100%
Made in Italy
Soft Enclosure
Instrument soft protection
enclosure

Bulk Soft Enclosures is a fast and economical alter-

native to traditional GRP enclosure. Manufactured

Soft Enclosures are available in various material

thicknesses to suit the particular application condi-
tions. Light weight yet robust construction means
that the enclosures are self-supporting, removing
the need for costly support frames or brackets. For
applications where the internal temperature is to be
controlled, electric heaters and associated control
equipment can be supplied as an integral part of the
enclosure.

Main Technical Data and

Characteristics
• Flame retardant
• Light weight
• Very low installation cost
•
gauge protection
• No support bracket needed
• Plastic socket for TAG label
•
• Suitable for steam or electric heating

Ambient Temperature From -50 to +150 °C

Cloth Material Double sided grey silicone impregnated glass cloth
Insulation from 10 to 20mm thick Mineral Wool Insulation as standard
Fixings & Fastening Black FR Velcro Hook & Loop Flaps with Draw Cords
Viewing Window PVC or FEP
Dimension
( instrument, valves, positioner, actuator, … ).

www.bulksrl.it Pag 20 100%

Made in Italy
External Mounting Bracket
Suitable for mounting enclosure or sunshade on 2” vertical stand pipe
Material of construction galvanized carbon steel or AISI 316
All nuts and washers are included

MODEL SP-S1 288

105 105

35

35
Suitable for:

12
133
- sunshade model 350 330

- enclosure model 700 ( rear

32
mounting )
Model SP-S1-CG made in hot Collare

60
dip galvanized carbon steel 3
TOLLERANZA GENERALE DOVE NON SPECIFICATO/GENERAL TO
LERANCE UNSPECIFIED

OLTRE

Model SP-S1-316 made in AISI

- 6 30 120 315 1000 2000
GRUPPO DIMENSIONI OVER
FINO A

Base
NOMINAL SIZE 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO + +
COARSE - 0.2 - 0.5 -+ 0.8 +
- 1.2 -+ 2.0 -+ 3.0 +
- 4.0

PRECISIONE
ACCURACY
GRADO DI
MEDIO + + + + + + +
FINE - 0.1 - 0.2 - 0.3 - 0.5 - 0.8 - 1.2 - 2.0

PRECISO
+
- 0.05 -+ 0.1 +
- 0.15 +
- 0.2 +
- 0.3 -+ 0.5
CLOCE

316
ANGOLI/ANGLES -+ 30'

VIA GIOTTO, 7 DISEGNATO DA:

MATERIALE/MATERIAL DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 10/04/2010
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE: AISI 316 L PIASTRA AD OMEGA PER 350 SP-S1-316
PHONE: +39-02-66307430 BONOMETTI ANDREA 0001
CHECKED BY: REVISION: PER PALINA 2"
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: BONOMETTI ANDREA SCALA/SCALE: 1/2.5
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

MODEL SP-S2
93,5

Suitable for:

200
- sunshade model 125
215

185
- sunshade model 250
- enclosure model 500 ( rear mounting )
Model SP-S2-CG made in hot dip galva-
60

80

nized carbon steel

3

TOLLERANZA GENERALE D OVE NON SPECIFICATO/GENER AL TOLERANCE UNSPECIFIED

Model SP-S2-316 made in AISI 316

OLTRE
- 6 30 120 315 1000 2000
GRUPPO DIMENSIONI OVER
NOMINAL SIZE FINO A 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO
-+ 0.2 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0 -+ 3.0 -+ 4.0
COARSE

ACCURACY
PRECISIONE
GRADO DI
TUBO DIAM.60 SP.2 MEDIO
FINE
+
- 0.1 +
- 0.2 +
- 0.3 +
- 0.5 +
- 0.8 +
- 1.2 +
- 2.0

PRECISO
CLOCE -+ 0.05 -+ 0.1 -+ 0.15 -+ 0.2 -+ 0.3 -+ 0.5

ANGOLI/ANGLES -+ 30'

VIA GIOTTO, 7 DISEGNATO DA:

MATERIALE/MATERIAL DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 04/03/2010
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE:
BONOMETTI ANDREA 0000 PIASTRA INTERNA ORIZZONTALE SP-I2-316
PHONE: +39-02-66307430 CHECKED BY: REVISION: AISI 316 L
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: HORIZONTAL MOUNTING BRACKET
BONOMETTI ANDREA SCALA/SCALE: 1/2.5
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

MODEL SP-S3

Suitable for:
- sunshade model 115
- sunshade model 125
Model SP-S3-CG made in galvanized carbon
steel
Model SP-S3-316 made in AISI 316

MODEL SP-E1 80

3
60

Suitable for:
- enclosure 500 ( bottom mounting )
215

185

- enclosure 700 ( bottom mounting )

Model SP-E1-CG made in hot dip galvanized
TUBO DIAM.70 SPESS.2

carbon steel 103

Model SP-E1-316 made in AISI 316

N.6 FORI DIAM.12
TOLLERANZA GENERALE DOVE NON SPECIFICATO/GENERAL TOLE RANCE UNSPECIFIED

OLTRE
- 6 30 120 315 1000 2000
GRUPPO DIMENSIONI OVER
NOMINAL SIZE FINO A 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO + + + + + + +
- 0.2 - 0.5 - 0.8 - 1.2 - 2.0 - 3.0 - 4.0
COARSE
ACCURACY
PRECISIONE
GRADO DI

MEDIO
FINE -+ 0.1 -+ 0.2 -+ 0.3 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0

PRECISO
CLOCE -+ 0.05 -+ 0.1 -+ 0.15 -+ 0.2 -+ 0.3 -+ 0.5

ANGOLI/ANGLES -+ 30'

VIA GIOTTO, 7 DISEGNATO DA:

DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 04/03/2010 MATERIALE/MATERIAL
PIASTRA DI FISSAGGIO
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE:
BONOMETTI ANDREA 0000 SU PALINA DA 2"
PHONE: +39-02-66307430 CHECKED BY: REVISION: AISI 316 SP-E1-316
Instrumental bulk material FAX: +39-02-93664351 MOUNTING BRACKET
APPROVATO DA: BONOMETTI ANDREA SCALA/SCALE: 1/2
E-MAIL: info@bulksrl.it APPROVED BY: FOR 2" PIPESTAND

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

Pag 21 www.bulksrl.it
Model SP-E1 is supplied complete with q.ty 2 C rails to allow versatility during
installation:

305 30
245

18
Model PR-500-CG made in hot dip gal-
vanized carbon steel, suitable for model

1.5
500
Model PR-500-316 made in AISI 316,
suitable for model 500
280
TOLLERANZA GENERALE DOVE NON SPECIFICATO/GENERAL TO
LERANCE UNSPECIFIED

OLTRE
- 6 30 120 315 1000 2000
GRUPPO DIMENSIONI OVER
NOMINAL SIZE FINO A 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO
COARSE -+ 0.2 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0 -+ 3.0 -+ 4.0

PRECISIONE
ACCURACY
GRADO DI
MEDIO
FINE -+ 0.1 -+ 0.2 -+ 0.3 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0

PRECISO
CLOCE -+ 0.05 -+ 0.1 -+ 0.15 -+ 0.2 -+ 0.3 +
- 0.5

ANGOLI/ANGLES -+ 30'

VIA GIOTTO, 7 DISEGNATO DA:

DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 02/03/2010 MATERIALE/MATERIAL
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE: PROFILATO A C PER 500
PHONE: +39-02-66307430 BONOMETTI ANDREA 0000
CHECKED BY: REVISION: IN AISI 316
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: AISI 316 PR-500-316
BONOMETTI ANDREA SCALA/SCALE: 1/2
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

550 30

18
Model PR-700-CG made in hot dip gal-
vanized carbon steel, suitable for model
1.5

700
Model PR-700-316 made in AISI 316,
suitable for model 700 525

TOLLERANZA GENERALE DOVE NON SPECIFICATO/GENERAL TO

LERANCE UNSPECIFIED

OLTRE
- 6 30 120 315 1000 2000
GRUPPO DIMENSIONI OVER
NOMINAL SIZE FINO A 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO
COARSE -+ 0.2 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0 -+ 3.0 -+ 4.0

PRECISIONE
ACCURACY
GRADO DI
MEDIO
FINE -+ 0.1 -+ 0.2 -+ 0.3 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0

PRECISO
+
- 0.05 +
- 0.1 +
- 0.15 +
- 0.2 +
- 0.3 +
- 0.5
CLOCE

ANGOLI/ANGLES -+ 30'

VIA GIOTTO, 7 DISEGNATO DA:

DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 02/03/2010 MATERIALE/MATERIAL
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE: AISI 316 PROFILATO A C PER 700 PR-700-316
BONOMETTI ANDREA IN AISI 316
PHONE: +39-02-66307430 CHECKED BY: REVISION: 0000
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: BONOMETTI ANDREA SCALA/SCALE: 1/2.5
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

model SP-S2 model SP-S2

OTHER BRACKETS ARE AVAILABLE FOR SPECIAL OR CUSTOM EXECUTION

www.bulksrl.it Pag 22
Suitable for mounting enclosure or sunshade to
wall
Material of construction galvanized carbon
steel or AISI 316
All nuts and washers are included ( not for wall
side )

mounting bracket

Suitable for mounting sunshade directly on

instrument
Material of construction galvanized carbon
steel or AISI 316
All nuts and washers are included

Pag 23 www.bulksrl.it
Internal Mounting Bracket
Suitable to support instrument / manifold
Material of construction galvanized carbon steel or AISI 316
All nuts and washers are included

MODEL SP-I1 TUBO DIAM.60 SP.2

303
Suitable for:
- enclosure 500 ( bottom mounting )

3
185

- enclosure 700 ( bottom mounting )

Model SP-I1-CG made in hot dip

80

60
galvanized carbon steel
Model SP-I1-316 made in AISI 316 TOLLERANZA GENERALE DOVE NON SPECIFICATO/GENERAL TO

GRUPPO DIMENSIONI
LERANCE UNSPECIFIED

OLTRE
OVER
- 6 30 120 315 1000 2000

215
NOMINAL SIZE FINO A 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO
COARSE -+ 0.2 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0 -+ 3.0 -+ 4.0

PRECISIONE
ACCURACY
GRADO DI
MEDIO
FINE -+ 0.1 -+ 0.2 -+ 0.3 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0

PRECISO
+
- 0.05 -+ 0.1 +
- 0.15 -+ 0.2 -+ 0.3 -+ 0.5
CLOCE

ANGOLI/ANGLES +
- 30'

VIA GIOTTO, 7 DISEGNATO DA:

MATERIALE/MATERIAL DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 04/03/2010
PIASTRA INTERNA
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE:
PHONE: +39-02-66307430 BONOMETTI ANDREA 0000 AISI 316 L SP-I1-316
CHECKED BY: REVISION:
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: BONOMETTI ANDREA SCALA/SCALE: 1/2.5
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

Model SP-I1 is supplied complete with q.ty 2 C rails to allow versatility during
installation:
305 30
245

18
Model PR-500-CG made in hot dip galva-
1.5

nized carbon steel, suitable for model 500

Model PR-500-316 made in AISI 316, suit-
able for model 500
280
TOLLERANZA GENERALE DOVE NON SPECIFICATO/GENERAL TO
LERANCE UNSPECIFIED

OLTRE
- 6 30 120 315 1000 2000
GRUPPO DIMENSIONI OVER
NOMINAL SIZE FINO A 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO
COARSE -+ 0.2 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0 -+ 3.0 -+ 4.0

PRECISIONE
ACCURACY
GRADO DI
MEDIO
FINE -+ 0.1 -+ 0.2 -+ 0.3 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0

PRECISO
CLOCE -+ 0.05 -+ 0.1 -+ 0.15 -+ 0.2 -+ 0.3 -+ 0.5

ANGOLI/ANGLES -+ 30'

VIA GIOTTO, 7 DISEGNATO DA:

DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 02/03/2010 MATERIALE/MATERIAL
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE: PROFILATO A C PER 500
PHONE: +39-02-66307430 BONOMETTI ANDREA 0000
CHECKED BY: REVISION: IN AISI 316
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: AISI 316 PR-500-316
BONOMETTI ANDREA SCALA/SCALE: 1/2
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

550 30
18

Model PR-700-CG made in hot dip galva-

1.5

nized carbon steel, suitable for model 700

Model PR-700-316 made in AISI 316, suit- 525

able for model 700

TOLLERANZA GENERALE DOVE NON SPECIFICATO/GENERAL TO
LERANCE UNSPECIFIED

OLTRE
- 6 30 120 315 1000 2000
GRUPPO DIMENSIONI OVER
NOMINAL SIZE FINO A 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO
COARSE -+ 0.2 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0 -+ 3.0 -+ 4.0
PRECISIONE
ACCURACY
GRADO DI

MEDIO
FINE -+ 0.1 -+ 0.2 -+ 0.3 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0

PRECISO
CLOCE -+ 0.05 -+ 0.1 -+ 0.15 -+ 0.2 -+ 0.3 -+ 0.5

ANGOLI/ANGLES -+ 30'

VIA GIOTTO, 7 DISEGNATO DA:

DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 02/03/2010 MATERIALE/MATERIAL
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE: AISI 316 PROFILATO A C PER 700 PR-700-316
BONOMETTI ANDREA IN AISI 316
PHONE: +39-02-66307430 CHECKED BY: REVISION: 0000
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: BONOMETTI ANDREA SCALA/SCALE: 1/2.5
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, D IVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY W RITTEN AUTHORIZATION FROM BULK SRL.

93,5

MODEL SP-I2

Suitable for:
200
215

185

- enclosure 500 ( bottom or rear mounting )

- enclosure 700 ( bottom or rear mounting )
Model SP-I2-CG made in hot dip galvanized
60

80

carbon steel
3

TOLLERANZA GENERALE D OVE NON SPECIFICATO/GENER AL TOLERANCE UNSPECIFIED

OLTRE
- 6 30 120 315 1000 2000
GRUPPO DIMENSIONI OVER

Model SP-I2-316 made in AISI 316

NOMINAL SIZE FINO A 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO
-+ 0.2 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0 -+ 3.0 -+ 4.0
COARSE
ACCURACY
PRECISIONE
GRADO DI

TUBO DIAM.60 SP.2 MEDIO

FINE -+ 0.1 -+ 0.2 -+ 0.3 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0

PRECISO
CLOCE -+ 0.05 -+ 0.1 -+ 0.15 -+ 0.2 -+ 0.3 -+ 0.5

ANGOLI/ANGLES -+ 30'

VIA GIOTTO, 7 DISEGNATO DA:

MATERIALE/MATERIAL DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 04/03/2010
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE:
BONOMETTI ANDREA 0000 PIASTRA INTERNA ORIZZONTALE SP-I2-316
PHONE: +39-02-66307430 CHECKED BY: REVISION: AISI 316 L
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: HORIZONTAL MOUNTING BRACKET
BONOMETTI ANDREA SCALA/SCALE: 1/2.5
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

www.bulksrl.it Pag 24
Model SP-I2 is supplied complete with q.ty 2 C rails to allow versatility during
installation:
305 30
245
Model SP-I2 is supplied complete with q.ty

18
2 C rails to allow versatility during installa-
tion:

1.5
Model PR-500-CG made in hot dip galva-
nized carbon steel, suitable for model 500
Model PR-500-316 made in AISI 316, suit-
280
able for model 500 TOLLERANZA GENERALE DOVE NON SPECIFICATO/GENERAL TO

GRUPPO DIMENSIONI
NOMINAL SIZE
LERANCE UNSPECIFIED

OLTRE
OVER
FINO A
UP TO
6
- 6

30
30

120
120

315
315

1000
1000

2000
2000

4000

GROSSOLANO +
COARSE - 0.2 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0 +
- 3.0 -+ 4.0

ACCURACY
PRECISIONE
GRADO DI
MEDIO + +
FINE - 0.1 - 0.2 -+ 0.3 -+ 0.5 -+ 0.8 +
- 1.2 -+ 2.0

PRECISO
+
- 0.05 -+ 0.1 -+ 0.15 -+ 0.2 +
- 0.3 +
- 0.5
CLOCE

ANGOLI/ANGLES -+ 30'

VIA GIOTTO, 7 DISEGNATO DA:

DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 02/03/2010 MATERIALE/MATERIAL
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE: PROFILATO A C PER 500
PHONE: +39-02-66307430 BONOMETTI ANDREA 0000
CHECKED BY: REVISION: IN AISI 316
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: AISI 316 PR-500-316
BONOMETTI ANDREA SCALA/SCALE: 1/2
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

550 30

18
Model PR-700-CG made in hot dip galva-
nized carbon steel, suitable for model 700 1.5

Model PR-700-316 made in AISI 316,

suitable for model 700 525

TOLLERANZA GENERALE DOVE NON SPECIFICATO/GENERAL TO

LERANCE UNSPECIFIED

OLTRE
- 6 30 120 315 1000 2000
GRUPPO DIMENSIONI OVER
NOMINAL SIZE FINO A 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO
COARSE -+ 0.2 -+ 0.5 +
- 0.8 -+ 1.2 -+ 2.0 -+ 3.0 -+ 4.0

PRECISIONE
ACCURACY
GRADO DI
MEDIO
FINE -+ 0.1 -+ 0.2 -+ 0.3 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0

PRECISO
CLOCE -+ 0.05 -+ 0.1 +
- 0.15 +
- 0.2 -+ 0.3 +
- 0.5

ANGOLI/ANGLES +
- 30'

VIA GIOTTO, 7 DISEGNATO DA:

DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 02/03/2010 MATERIALE/MATERIAL
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE: AISI 316 PROFILATO A C PER 700 PR-700-316
BONOMETTI ANDREA IN AISI 316
PHONE: +39-02-66307430 CHECKED BY: REVISION: 0000
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: BONOMETTI ANDREA SCALA/SCALE: 1/2.5
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

302

200

MODEL AP-1

Suitable for:
- enclosure 500 ( rear mounting )
185

207

Model AP-1-CG made in galvanized car-

bon steel
Model AP-1-316 made in AISI 316 TOLLERANZA GENERALE DOVE NON SPECIFICATO/GENERAL TOLERANCE UNSPECIFIED

OLTRE
- 6 30 120 315 1000 2000
GRUPPO DIMENSIONI OVER
NOMINAL SIZE FINO A 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO
COARSE -+ 0.2 +
- 0.5 -+ 0.8 -+ 1.2 -+ 2.0 -+ 3.0 -+ 4.0
ACCURACY
PRECISIONE
GRADO DI

SPESSORE / THICKNESS 3mm MEDIO

FINE
+
- 0.1 +
- 0.2 +
- 0.3 +
- 0.5 +
- 0.8 +
- 1.2 +
- 2.0

PRECISO + +
CLOCE - 0.05 - 0.1 -+ 0.15 +
- 0.2 +
- 0.3 +
- 0.5

ANGOLI/ANGLES -+ 30'

VIA GIOTTO, 7 DISEGNATO DA:

MATERIALE/MATERIAL DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 02/03/2010
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE:
BONOMETTI ANDREA 0001 PIASTRA DI FISSAGGIO AP-1-316
PHONE: +39-02-66307430 CHECKED BY: REVISION: AISI 316 L
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: FIXING BRACKET
BONOMETTI ANDREA SCALA/SCALE: 1/2
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

MODEL AP-2 610

570

Suitable for:
- enclosure 700 ( rear mounting )
360

320

Model AP-2-CG made in galvanized car-

bon steel
Model AP-2-316 made in AISI 316 TOLLERANZA GENERALE DOVE NON SPECIFICATO/GENERAL TOLERANCE UNSP

OLTRE
ECIFIED

- 6 30 120 315 1000 2000

GRUPPO DIMENSIONI OVER
NOMINAL SIZE FINO A 6 30 120 315 1000 2000 4000
UP TO

GROSSOLANO
-+ 0.2 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0 -+ 3.0 -+ 4.0
COARSE
PRECISIONE
ACCURACY
GRADO DI

MEDIO
FINE -+ 0.1 -+ 0.2 -+ 0.3 -+ 0.5 -+ 0.8 -+ 1.2 -+ 2.0

PRECISO
+
- 0.05 +
- 0.1 +
- 0.15 +
- 0.2 +
- 0.3 +
- 0.5
CLOCE

ANGOLI/ANGLES -+ 30'

VIA GIOTTO, 7 DISEGNATO DA:

MATERIALE/MATERIAL DESCRIZIONE/DESCRIPTION CODICE / CODE
BULK SRL 20032 CORMANO (MILANO) DRAWNED BY:
MUOLO EMANUELE DATA/DATE: 25/02/2013
PHONE: +39-02-66307514 CONTROLLATO DA: REVISIONE:
BONOMETTI ANDREA 0000
PHONE: +39-02-66307430 CHECKED BY: REVISION: PIASTRA DI FISSAGGIO AP-2-316
AISI 316 L
Instrumental bulk material FAX: +39-02-93664351 APPROVATO DA: FIXING BRACKET
BONOMETTI ANDREA SCALA/SCALE: 1/5
E-MAIL: info@bulksrl.it APPROVED BY:

IL PRESENTE DISEGNO E' DI PROPRIETA' DELLA BULK SRL. LA SUA RIPRODUZIONE O DIVULGAZIONE SARA' THIS DRAWING IS PROPERTY OF BULK SRL. REPRODUCTION, DIVULGATION AND USE FOR PURPOSE DIFFERENT FROM
PERMESSA SOLO SU SPECIFICA AUTORIZZAZIONE ED IN ACCORDO AI TERMINI DI LEGGE THOSE IT HAS BEEN ISSUED ARE FORBIDDEN WITHOUT ANY WRITTEN AUTHORIZATION FROM BULK SRL.

Pag 25 www.bulksrl.it
Examples

SP-I2 SP-I1

model AP-1

OTHER BRACKETS ARE AVAILABLE FOR SPECIAL OR CUSTOM EXECUTION

2” PIPE STAND Model PAL-X-CG made

in hot dip galvanized
Suitable to sup- carbon steel ( replace
port sunshade or X with required height
enclosure dimension in mm )
Material of construc- Model PAL-X-316 made
tion hot dip galva- in AISI 316 ( replace
nized carbon steel or X with required height
AISI 316 dimension in mm )
Complete with
square base provid-
ed with q.ty 4 holes
12 mm diameter

shape and painting

available on request.
www.bulksrl.it Pag 26
Cooling and Heating
Instrument enclosures are commonly used to protect instrumentation against adverse
weather conditions and to ensure that the instrument operates at the proper tempera-

in damages to sensitive equipment. The best way to solve this problem is to equip BULK
GRP enclosures with accessories designed to maintain interior temperature within the

Heat could be generate by electrical heater or by steam heating coil.

Electrical heater has self regulating construction but it can be also supplied complete
with thermostat ( in line or separate ).

temperature switch, heat tracing.

length.
It is possible to control the heating by using a thermostatic valve.

If heat dispersion is needed, enclosure can be supplied complete of metallic louvre

grilles.
Louvres allows ventilation, preventing excessive heat or gas/vapour presence inside of
enclosure.

Pag 27 www.bulksrl.it
Accessories
PROCESS AND DRAIN TUBING

Process and drain tubing should go through enclosure wall by using one of the follow-
ing option:

Material of construction AISI 316

( other material available on request )
Size from 1/16” o.d. to 1” o.d.,
from 3 mm o.d. to 25 mm o.d.

Bulkhead union model UP

Bulkhead male connector model DMP

Bulkhead female connector model DFP

Rubber grommets

Standard material of construction EPDM

Temperature range -35°C + 110°C
( available also in other material for temperature down
to – 55°C )

• 6 mm or ¼” o.d. tubing
• 10 mm or 3/8” o.d. tubing
• 12 mm or ½” o.d. tubing
• other dimension available on request ( 14 mm,
22 mm, …. )
www.bulksrl.it Pag 28
Special plate

In case of application with capillary impulse

line, a special plate should be use.

requirement

POWER SUPPLY AND SIGNAL CABLES

Power supply and signal cables must go through enclosure wall by using of cable
glands.

type and size, …

Material of construction for cable gland: polyamide, brass, nickel plated brass, AISI
304/316/316L.
Available for armoured ( double seal ) or not armoured cable ( single seal ).
Standard thread M20, other size available on request.
Explosion proof or standard execution for safe area available.

Grommets could be also use for this purpose.

PREINSULATED AND PRETRACED TUBING

Preinsulated and pretraced tubing should

go through enclosure wall by using of
heat-shrinkable.

according to the application.

INSTRUMENT MANIFOLD

It is available a wide range of instrument manifold especially designed for application

inside of the enclosure.

Pag 29 www.bulksrl.it
 INFORMATION LABEL

Information label could be useful to identify instrument TAG number placed inside of

All information, including possible references / instruction / warnings, are permanently

engraved on the label.

Model TAG-ITEM: made in AISI 316

VENT AND DRAIN DEVICE

Breather drain allows condensation to drain out from enclosure.

Material of construction is polyamide or AISI 316
Explosion proof or standard execution for safe area.
Valve is located on lower point of the enclosure.
Model D-1 is made in polyamide
Model D-2 is made in AISI 316

www.bulksrl.it Pag 30
Customized Product
The following are some examples of custom product made in the past years:

Painted sunshade and enclosure

I t is po ssible to su pply o u r su n sh ade an d en clo su r e

painted in any industrial color, in according to
international standard as RAL or Munsell and to

“sunshade serie 125 painted

RAL 9010 for KNPC”

Colored sunshade and enclosure

It is possible to supply our sunshade and enclo-

production.
Availability and cost impact depends from quan-
tity.

“enclosure serie 500 pigmented RAL

5017 for Gazprom”
Self-supporting sunshade

instrument installed on top of boiler, magnetic

-
tuator, ... ), it is possible to use our self-supporting
sunshade.
Mounting bracket material is made in galvanized
carbon steel or AISI 316
All nuts and washers are included

“self standing sunshade for ABB”

Pag 31 www.bulksrl.it
Shaped sunshade

( i.e. alarm lamps, sirens, … )

”sunshade serie 350 shaped for

sirens for Takreer”

Stainless and carbon steel sunshade

than GRP ( i.e. AISI 304, AISI 316, galvanized carbon

steel, … ).
Dimension and shape are made as per customer’s
requirement.

Valve actuator and positioner protection

If upper part of control valve needs protection from

external environment, we can insert it into our enclo-

Partial enclosure

Our partial enclosure model 300 is available when in-

strument body is heated with high temperature steam
tracing.
This enclosure protect only the instrument body, while
electronic housing and display are outside to avoid a
possible overheating.

0° - 90° Sunshade
If the instrument indicator is located on the top, a 0°-90° sunshade hinge allows

Sunshade is kept on 0° position by a manual lock.

Mounting bracket material is made in galvanized carbon steel or AISI 316
All nuts and washers are included.
www.bulksrl.it Pag 32
The ability to verify the real performance of our products

independent laboratories.
The repeatability of the production systems, the materials

UV ray
Direct exposure to sunlight is a deteriorating factor in the
industrial life of the equipment and the enclosures or sun-
shade which protects it.

are both the thermosetting composition as well as the sur-

the attack of UV rays were performed in a laboratory with

simulate the aging process and assess its degree of degra-

dation, durability and strength.
The mechanical resilience tests before and after the irradi-

the acceptability criteria of the standard.

(IMQ 43SL00177 Test Report)

the plastic elements must guarantee self-extinguishing

Tests conducted on the composite according to UL 94 pro-

cedures showed a full compliance to the standard V0.
(Istituto Giordano test report 311399)

Pag 33 www.bulksrl.it
Watertight integrity
The watertight integrity of an enclosure is essential to
preserve the instruments from water, humidity, dust and
sand.

a seal placed inside the proper perimeter grooves.

To verify the watertight structure according to Class IP66,

The tests conducted for the resistance to the penetration

of dust and water provided full compliance to IP66 re-
quirement
(Test report NEMKO 189859-1 TRFENV and 189859-2
TRFENV)

Wind resistance
Often enclosures and sunshades are installed in areas
with the presence of high speed wind.
Resistance to such a solicitation of the structure and the
related mounting bracket was evaluated during two days
of testing in the wind tunnel at the Milan Polytechnic Uni-
versity.

resisted gusts of 160 km/h.

(Report P 48-07 at the Milan Polytechnic Institute Me-
chanical Department)

ATEX
-
quires an Analysis of Risks such as with ignition sources.
The main danger for enclosures and sunshades is the
insulating properties of GRP which can generate super-

sustained wind speeds.

To ensure a safe installation, BULK has developed a line
of products made with a graphite charge having a sur-
face resistivity lower than required by the standard.
-
ited laboratory have yielded positive results, even to the
most stringent requirements.
Relative documents submitted by the certifying body al-

applicable to “Non-electrical equipment intended for

use in potentially explosive atmosphere as per Directive
2014/34/UE”).

www.bulksrl.it Pag 34
EAC CU TR

instrument enclosure and sunshade in the following coun-

tries: Russia, Belarus and Kazakhstan
One of the developments of the Customs Union (rati-

GOST.

our entire range of products to the stringent legal require-

ments and Technical Regulations (TR CU).
For standard sunshades & enclosures are available CER-
TIFICATE OF COMPLIANCE TO EAC TR CU 010/2011 ON
SAFETY OF MACHINERY AND EQUIPMENT. While for sun-
shades & enclosures suitable for hazardous area instal-
lation CERTIFICATE EAC TR CU 012/2011 ON SAFETY OF
EQUIPMENT FOR USE IN POTENTIAL EXPLOSIVE ATMOS -
PHERE is available.

SAND & SALT MIST

closed to sea and to desert areas.

The combination of salt mist and sand could quickly de-
teriorate components made in steel even if protected by

Test made in saline and salt chamber in according to MIL-

STD-810G METHOD 510.5 standard, gave a 100% positive
result: GRP component resist without any deterioration to
sand and salt corrosion.
(KIWA test Report 150700274)

Power heating sizing

The selection of the correct power in an electrical heater is
usually based on generic calculations provided by heater
manufactures.
To ensure the correct dimensions of heating elements,
heat dispersion tests were conducted in a climate cham-
-
peratures.
(NEMKO PT0092/04 Test Report)

Pag 35 www.bulksrl.it
 Dimensions are for reference only, and are subject to change without notice.
All right reserved.
All dimensions are in millimeters.

www.bulksrl.it