Scribd
Upload
59 views5 pages

Service Documentation: Market Release 2/90

This document provides service documentation for the Braun pocket battery deluxe model 5524, including an exploded drawing of the components, spare parts list, and service information. The key points are: 1) The 5524 is a battery-powered shaver with plastic housing and shaving head frame. It uses a removable 40mm shaving foil and 30 cutter blades. 2) It is powered by two 1.5V batteries and has an operating current of around 500mA. 3) Disassembly involves removing the batteries and cutting parts, then separating the upper and lower housing which are held together by snaps. Assembly follows the reverse order.

Uploaded by

Eprom Servis
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
59 views5 pages

Service Documentation: Market Release 2/90

This document provides service documentation for the Braun pocket battery deluxe model 5524, including an exploded drawing of the components, spare parts list, and service information. The key points are: 1) The 5524 is a battery-powered shaver with plastic housing and shaving head frame. It uses a removable 40mm shaving foil and 30 cutter blades. 2) It is powered by two 1.5V batteries and has an operating current of around 500mA. 3) Disassembly involves removing the batteries and cutting parts, then separating the upper and lower housing which are held together by snaps. Assembly follows the reverse order.

Uploaded by

Eprom Servis
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Service Documentation Market Release 2/90

Braun pocket battery deluxe 5524

5524
BINC Rev: 7/96 Service Documentation
Exploded Drawing
BAG Rev: 2/90 5524

5524 - 2
BINC Rev: 7/96 Service Documentation
Spare Parts List
BAG Rev: 7/95 5524

Pos. No. Part Description Part Number


1 Cleaning brush 5524804
2 Protective cap 5524802
3 Shaving head frame 5523624
4 Shaving foil 5524764
5 Cutter block 5524761
6 Circlip 0107001
7 Cutter block support, w/pos. no 8 5523812
9 Conical coil spring 5523042
10 Oscillating frame 5523510
11 Eccentric 5523807
12 Motor 5523626
13 Switch handle 5523034
14 Housing, upper part 5524611
15 Housing, lower part 5524629
16 Spring 5523018
17 Spring catch 5523016
18 Battery cover 5524096

5524 - 3
BINC Rev: 7/96 Service Documentation
Service Information
BAG Rev: 2/90 5524

Description of shaver

Battery shaver
Housing: Plastic
Shaving head frame: Plastic
Shaving foil: 40 mm wide, removable (snap connection)
Cutter block: 30 cutter blades, 3° obliquely positioned, 10 mm diameter, plastic
Protective cap:
for pocket battery: removal with clamp for cleaning brush
for pocket deluxe: swivel protective cap integrated in the unit with locking.

General Information

Drive: 2.7 V direct-current motor. Power transmission to cutter block by


means of eccentric and plastic oscillating frame.

Power supply: Supply by means two 1.5 V Mignon cells (type LR6/AM3/
MN 1500/AA alkaline).

Technical data

1 Amplitude at the cutter block: approx. 2.4 min.


2. Rotational speed: approx. 6200 r.p.m.
3. Operating current: approx. 500 mA
4. Operating capacity: approx. 60 shaving minutes

5524 - 4
BINC Rev: 7/96 Service Documentation
Service Information
BAG Rev: 2/90 5524

Disassembly

• Remove batteries, take off cutting parts.


• Disassemble cutter block support with rubber seal.
• The housing halves are held together by snap-action. Apply pressure diagonally on sides of
housing and squeeze, until parts disengage.
• Start at battery well to separate housing parts.
• Attention! Spring (16) and catch (17) will jump out of housing parts, also the battery cover
(18) will drop out.
• Motor (12) with oscillating frame (10) can now be removed from housing, lower part (15).

Assembly

The assembly will be accomplished in a reversed sequence. Attention should be paid to the
following points:

• The motor (12) must be installed with correct polarity. The minus-pole of the motor (the
motor contact which is not soldered), must be pinched between the battery contact.
• Insert oscillating frame (10) in such away, to line-up with the upper edge of the housing.
• First engage housing halves on the upper side, put battery cover (18) into place at the
bottom, then press both parts together.
• Assemble cutter block support (7) and pull rubber seal (8) over bead on housing.
• After housing has been assembled, slide spring catch (17) with spring (16) into the pockets

Insert batteries, carry out functional tests.

5524 - 5

You might also like