1101

Globe valves
d Straight seat type
PN 10-40 DN 15-300

4
Design
Acc. to DIN 3356
12
Top part
17,18 Outside screw
Rising Handwheel
3 Rising stem

2 H
___ Stem sealing
H1 Stuffing box
15

23,24 Obturator
Disk
16
Body seat
Integral seat
8

Valve ends
10
Flanges acc. to
EN 1092-1 (DIN 2501
5
Part 1)
1
Requirements and tests
Acc. to DIN 3356 Part 1
b
Marking
L Nominal size DN
Nominal pressure PN
Body material
Manufacturer brand
Flow direction arrow
Pos. Denomination Material Pos. Denomination Material
1.4308 1.4408 1.4308 1.4408
1 Body 1.4308 1.4408 15 Packing Graphite Graphite
2 Yoke 1.4308 1.4408 16 Gasket Graphite / Graphite /
3 Gland 1.4541 1.4571 1.4401 1.4401
4 Hand wheel GTS/GTW GTS/GTW 17 Hasp screw 1.4541 1.4571
5 Disk 1.4541 1.4571 18 Hex. Nut A2 A4
8 Stem 1.4541 1.4571 23 Stud bolt A2-70 A4-70
10 Disk screwing 1.4541 1.4571 24 Hex. Nut A2 A4
12 Sleeve 1.4021 1.4021
1
further materials are shown in the technical part

Face-to-face dimension acc. to EN 558 series 1 (DIN 3202-F1)

DN 15 20 25 32 40 50 65 80 100 125 150 200 250 300
L 130 150 160 180 200 230 290 310 350 400 480 600 730 850
H 175 225 225 230 270 285 340 370 410 460 535 635 640 760
H1 185 240 240 250 300 320 360 395 450 515 585 695 720 850
Ød 100 120 120 120 140 160 180 180 200 225 250 280 320 360
PN b 24 26 26
10 use PN 16
kg 146
PN b use PN 40 18 20 20 22 22 24 26 28
16 kg 21 35 48 57 90 146
PN b 30 32 392
25 use PN 40
kg 185
PN b 16 18 18 18 18 20 22 24 24 26 28 34 38 472
40 kg 5 6 7 10 12 17 23 37 53 64 98 192
kVS 4 6,3 10 16 25 40 63 100 160 250 360 630 1000 1400
2
reinforced against DIN / EN

10/2010
 1101
Globe valves
Straight seat type
PN 10-40 DN 15-300

Pressure/Temperature ratings in bar g at Temperature in °C

Material PN 50°C 100°C 120°C 150°C 200°C 250°C 300°C
»1.4308« 10 10,0 7,7 7,7 6,7 5,7 5,2 4,8
GX5CrNi19-10 16 16,0 12,3 12,3 10,7 9,1 8,4 7,7
EN 10213 25 25,0 19,2 19,2 16,7 14,2 13,1 12,1
40 40,0 30,8 30,8 26,8 22,8 21,0 19,4
»1.4408« 10 10,0 8,2 8,2 7,2 6,2 5,7 5,1
GX6CrNiMo18-10-2 16 16,0 13,2 13,2 11,6 10,0 9,1 8,2
EN 10213 25 25,0 20,7 20,7 18,1 15,7 14,2 12,8
40 40,0 33,1 33,1 29,0 25,1 22,8 20,5

Modifications Additional equipment

Indicator Chain wheel

Relief plug / By-pass disk Stem extension
Heating jacket Gear
Extended bonnet Electric actuator
Soft seated disk Pneumatic actuator
Conical seat
Throttle plug / Regulating disk

Relief plug / By-pass disk

Installation

Piping is to bed in such a manner that injurious thrust and bending forces are kept away from the valve casings.
Globe valves are usually installed thus allowing the liquid to enter below the plug and to leave above it. Globe
valves can also be installed in pipelines with changing flow directions up to the under mentioned differential
pressures between the working pressure before the closing plug and the back pressure behind it. As soon as these
differential pressures will be exceeded, relief plugs have to be provided for. These have to be installed in such a
way that the pressure to be sealed has to be above the plug.

Nominal size DN 125 150 200 250 300

p [bar] 33 21 14 9 6

The relief plug has the function of a by-pass and can only serve its purpose when after opening a back pressure is
built up so that the differential pressure becomes smaller than the figures in the above table. If this is not possible,
special designs are necessary. In this case we need the exact working conditions.
When turning the handwheel it is not allowed to use additional levers.

10/2010 - 1101.100-400.202/205e – Subject to change without notice

 1101
Globe valves
d Straight seat type
PN 63-160 DN 15-200

4
Design
Acc. to DIN 3356
12
Top part
17,18 Outside screw
Rising Handwheel
3 Rising stem

2 H
___ Stem sealing
H1 Stuffing box
15

23,24 Obturator
Disk
16
Body seat
Integral seat
8

Valve ends
10
Flanges acc. to
EN 1092-1 (DIN 2501
5
Part 1)
1
Requirements and tests
Acc. to DIN 3356 Part 1
b
Marking
L Nominal size DN
Nominal pressure PN
Body material
Manufacturer brand
Flow direction arrow
Pos. Denomination Material Pos. Denomination Material
1.4308 1.4581 1.4308 1.4581
1 Body 1.4308 1.4581 15 Packing Graphite Graphite
2 Yoke 1.4308 1.4581 16 Gasket 1.4541 / 1.4571 /
3 Gland 1.4541 1.4571 (grooved) Graphite Graphite
4 Hand wheel GTS/GTW GTS/GTW 17 Hasp screw 1.4541 1.4571
5 Disk 1.4541 1.4571 18 Hex. Nut A2 A4
8 Stem 1.4541 1.4571 23 Stud bolt A2-70 A4-70
10 Disk screwing 1.4541 1.4571 24 Hex. Nut A2 A4
12 Sleeve 1.4021 1.4021
1
further materials are shown in the technical part

Face-to-face dimension acc. to EN 558 series 2 (DIN 3202-F2)

DN 15 20/25 25 32 40 50 65 80 100 125 150 200
L 210 230 230 260 260 300 340 380 430 500 550 650
H 280 285 285 300 345 345 405 445 430 550 500 565
H1 285 293 293 310 357 360 438 470 460 588 545 625
Ød 140 140 140 160 200 200 200 250 250 320 320 360
PN b 26 26 28 30 34 36 42
63 kg 27 48 60 73 125 159 241
PN b use PN 160 --- --- ---
100 use PN 160
kg --- --- ---
PN b 20 22 24 26 28 30 34 36 40 --- --- ---
160 kg 11 13 14 20 28 40 53 92 99 --- --- ---
kVS 4 6,3 10 16 25 40 63 100 160 250 360 630

10/2010
 1101
Globe valves
Straight seat type
PN 63-160 DN 15-200

Pressure/Temperature ratings in bar g at Temperature in °C

Materials PN 50°C 100°C 120°C 150°C 200°C 250°C 300°C 350°C 400°C 450°C 500°C 550°C
»1.4308« 63 63,0 48,6 48,6 42,3 36,0 33,1 30,6
GX5CrNi19-10 100 100,0 77,1 77,1 67,1 57,1 52,5 48,5
EN 10213 160 160,0 123,4 123,4 107,4 91,4 84,1 77,7
»1.4581« 63 63,0 57,6 57,6 53,2 48,6 45,7 43,2 40,3 37,8 36,0 34,2 32,4
GX5CrNiMonB19-11-2 100 100,0 91,4 91,4 84,5 77,1 72,5 68,5 64,0 60,0 57,1 54,2 51,4
EN 10213 160 160,0 146,2 146,2 135,3 123,4 116,1 109,7 102,4 96,0 91,4 86,8 82,2
For temperatures > +400°C: Bolting material 1.7709

Modifications Additional equipment

Indicator Chain wheel

Relief plug / By-pass disk Stem extension
Heating jacket Gear
Extended bonnet Electric actuator
Soft seated disk Pneumatic actuator
Conical seat
Throttle plug / Regulating disk

Relief plug / By-pass disk

Installation

Piping is to bed in such a manner that injurious thrust and bending forces are kept away from the valve casings.
Globe valves are usually installed thus allowing the liquid to enter below the plug and to leave above it. Globe
valves can also be installed in pipelines with changing flow directions up to the under mentioned differential
pressures between the working pressure before the closing plug and the back pressure behind it. As soon as these
differential pressures will be exceeded, relief plugs have to be provided for. These have to be installed in such a
way that the pressure to be sealed has to be above the plug.

Nominal size DN 65 80 100 125 150 200

p [bar] 110 70 44 33 21 14

The relief plug has the function of a by-pass and can only serve its purpose when after opening a back pressure is
built up so that the differential pressure becomes smaller than the figures in the above table. If this is not possible,
special designs are necessary. In this case we need the exact working conditions.
When turning the handwheel it is not allowed to use additional levers.

10/2010 - 1101.500-700.202/206e – Subject to change without notice