TWO-POST LIFT

Model:210C 210CX
 CONTENTS

Product Features and Specifications ..............................................1

Installation Requirement .............................................................4

Steps of Installation ………………………………………………………..…………..........5

Exploded View ...........................................................................22

Test Run ...................................................................................25

Operation Instruction .................................................................27

Maintenance .............................................................................27

Trouble Shooting .......................................................................28

Parts List ………...........................................................................29

1
 I. PRODUCT FEATURES AND SPECIFICATIONS
CLEARFLOOR DIRECT-DRIVED MODEL FEATURES
MODEL 210C (See Fig.1)
· Direct-driving design, minimize the lift wear parts and breakdown ratio.
· Dual hydraulic direct-drive cylinders, designed and made as standard, utilizing oil
seal in cylinder.
· Self-lubricating UHMW Polyethylene sliders and bronze bush.
· Single-point safety release, and dual safety design.
· Clear-floor design, provide unobstructed floor space.
· Overhead safety shut-off device.
·With 4 three stages arms, make lifts easily find the lift point of the car.
· Stackable adapters 1.5”, 2.5”, 5” as standard.

Fig. 1
MODEL 210C SPECIFICATIONS

Width Minimum
Lifting Lifting Overall Overall Gross
Model Style Lifting Height Between Pad Motor
Capacity Time Height Width Weight
Columns Height

4500kgs 1940-2169mm 3854mm 3516mm 2850mm 90mm

Clear-floor 762Kg
210C 60S 3.0HP
Direct-drive
10,000lbs 76 3/8”-85 3/8” 151 3/4” 138 3/8” 112 1/4” 3 1/2” 1,719lbs

1
 CLEARFLOOR DIRECT-DRIVED MODEL FEATURES
MODEL 210CX (See Fig.2)
· Direct-driving design, minimize the lift wear parts and breakdown ratio.
· Dual hydraulic direct-drive cylinders, designed and made as standard, utilizing oil
seal in cylinder.
· Self-lubricating UHMW Polyethylene sliders and bronze bush.
· Single-point safety release, and dual safety design.
· Clear-floor design, provide unobstructed floor space.
· Overhead safety shut-off device.
·With 4 three stages arms
· Stackable adapters 1.5”, 2.5”, 5” as standard.

Fig. 2

MODEL 201CX SPECIFICATIONS

Width Minimum Gross
Lifting Lifting Overall Overall Weight
Model Style Lifting Height Between Pad Motor
Capacity Time Height Width
Columns Height
4500kgs 1940-2169mm 3854mm 3666mm 3000mm 90mm 764Kg
Clear-floor
210CX 60S 3.0HP
Direct-drive 10,000lbs 76 3/8”-85 3/8” 151 3/4” 144 3/8” 118 1/8” 3 1/2” 1,730lbs

2
Arm Swings View
For Model 210C

Fig. 3

For Model 210CX

Fig. 4

3
II. INSTALLATION REQUIREMENT
A. TOOLS REQUIRED
 Rotary Hammer Drill (Φ19)  Carpenter’s Chalk

 Hammer  Screw Sets

 Level Bar  Tape Measure (7.5m)

 English Spanner (12")  Pliers

 Ratchet Spanner With Socket (28#)  Socket Head Wrench (3#, 6#)

  Lock Wrench
Wrench set
(10#, 13#, 14#, 15#, 17#, 19#, 24# ,27#)

Fig. 5

4
B. SPECIFICATIONS OF CONCRETE (See Fig. 6)
Specifications of concrete must be adhered to the specification as following.
Failure to do so may result in lift and/or vehicle falling.
1. Concrete must be thickness 100mm minimum and without reinforcing steel bars，
and must be dried completely before the installation.
2. Concrete must be in good condition and must be of test strength 3,000psi
(210kg/cm²) minimum.
3. Floors must be level without cracks.

Fig. 6

67 Concrete intensive must be

210kg/cm² minimum

C. POWER SUPPLY
The electrical source must be 2.2KW minimum. The source cable size must be
2.5mm² and in good condition of contacting with floor.

III. STEPS OF INSTALLATION

A. Location of Installation
Check and insure the installation location (concrete, layout, space size etc.) is
suitable for lift installation.
B. Use a carpenter’s chalk line to establish installation layout of base plate (See Fig. 7).

Model 210C 210CX

Chalk Line

Fig. 7
5
C. Check the parts before assembly
1．Packaged lift and hydraulic power unit (see Fig. 8)

Fig. 8
2. Move the lift aside with a fork lift or hoist, and open the outer packing carefully ，

take off the parts from upper and inside the column, take out the parts box，check

the parts according to the shipment parts list (See Fig. 9).

Parts box.
Top beam Serial number
Shipment Parts Fig. 9

3. Loose
list the screws of the upper package stand, take off the upper column and remove

the package stand.

4. Move aside the parts and check the parts according to the shipment parts list
4.1 For Model 210C (See Fig. 10,11).

Fig. 11
Fig. 10 76
Parts in the parts box (76)
Parts in the shipment parts list 6
4.2 For Model 210CX (See Fig. 12,13).

77
Fig. 12 Fig. 13
Parts in the shipment parts list Parts in the parts box (77)

5．Open the bag of parts and check the parts of the parts bag according to parts bag

list (See Fig. 14).

Fig. 14

7
D. Position power side column
Lay down two columns on the installation site parallel, position the power side
column according to the actual installation site. Usually, it is suggested to install
power side column on the front-right side from which vehicles are driven to the lift
(See Fig. 15).
Oil hose passes through the
Power side column
Offside column retainer on column

Car-in direction

Fig. 15

E. Connecting oil hose

Push the carriages, connecting the cylinder fittings and then connect the oil hose to
the cylinder.

Install cylinder fittings Mounted

and oil hose
Fig. 16

8
F. Connecting cables 74

attention

Cables pass through from the Cables pass through the

bottom of the carriages top plate of the carriages

Fig. 17

G. Lay down aside the columns with cables and oil hoses installed, face the
open way of each columns.

210C overall width: 3516mm 210CX overall width:3666mm

Notch is relatively

Fig. 18

9
H. Position columns
Position the columns on the installation layout of base plate. Install the anchor bolts.
Do not tighten the anchor bolts (See Fig.19).

Width between columns

of 210C：2850mm

Width between columns

of 210CX：3000mm

Anchor Bolt

Note: Minimum embedment of

anchors is 90mm.
90mm

Drilling Cleaning Bolting

Fig. 19

10
I. Assemble overhead top beam (See Fig.20).

Fig. 20

J. Check the vertical of the columns with level bar, and adjusting with the shims if the
columns are not vertical. Tighten the anchor bolts (See Fig.21).

Adjusting with
Note: Torque of Anchors is
the shims Measure the
150N.m
vertical of column
Tighten
from front and
side by a lever bar
or not.

Fig. 21
67A/67B
11
K. Install the limit switch control bar and limit switch (See Fig. 22).

Use 3# Socket Head

Wrench to loosen the
Screw of drive rod
for adjustment
Adjust Drive Rod
of Limit Switch

Connect the blue wire to

terminal #11 on limit switch
and terminal A1 on AC
contactor of power unit.
Limit switch is connected
Connect the brown wire to with cable
terminal #12 on limit switch
and terminal #4 on button of
power unit

Connect the yellow and green

Fig. 22

wire to earth wire terminal on

limit switch and earth wire
terminal of power unit

NC: Normal contact

12 44
L. Install safety cable (See Fig. 23).

Pass through safety cable

View B
View A

Fig. 23

13
M. Install cables (See Fig. 24).

Fig. 24

14
N. Assembly oil hose.
1. For model 210C (See Fig. 25).

Fig. 25

15
2. For model 210CX (See Fig. 26).

Fig. 26

16
O. Install power unit and oil hoses (See Fig. 27)

After installing the fitting of

the power unit, tighten the
nut with 19# Wrench

Fig. 27
Tighten all the hydraulic fittings, and fill the reservoir with hydraulic oil.
Note: In consideration of Hydraulic Power Unit’s durability and keep the equipment
running in the perfect condition, please use Hydraulic Oil 46#.

17
P. Install lifting arms and adjust the arm locks

1. Install the lifting arms (See Fig. 28).

2. Lowering the carriages to the lowest position, then use the 8# wrench to loosen the
nut of arm lock (See Fig. 29).

Use the 8# wrench to

loosen the nut

Snap Ring

Fig. 28
Fig. 29

3. Adjust the arm lock as direction of arrow (See Fig. 30)

4. Adjust the moon gear and arm lock to make it to be meshed, then tighten the nut of
arm lock (See Fig. 31).

Adjust the moon gear

Lock the nuts after the moon gear
and arm lock are engaged well

Lock the nut

Fig. 30 Fig. 31

18
Q. Install electrical system
Connect the power source on the data plate of power unit.
Note: 1. For safety of operators, the power wiring must contact the floor well.

2. Pay attention to the direction of rotations when using three phase

motors.

Single phase motor (See Fig. 32).

1. Connecting the two power supply lines (Active L and Neutral wire N) to terminals of AC
contactor marked L1, L2 respectively.
2. Connecting the two motor wires to terminals of AC contactor marked T1, T2.
3. Connecting A2 to L2 of AC contactor.
4. Connecting the Limit Switch: Removing the wire of connecting terminal 4# on
control button and terminal A1 on AC contactor firstly (See Fig. 33), then connecting
wire 12# (brown color) of the limit switch with terminal 4# of the control button
and connecting wire 11# (blue color) with terminal A1 on AC contactor respectively.
Connecting the earth wire (green and yellow color) of the limit switch with earth wire
terminal on power unit. (See Fig. 34).
5. Connecting terminal 3# on control button with terminal L1 of AC contactor.

AC contactor

Fig. 32

19
 Motor Line

L1 N 3#
3#
L
A1
11#
4#
12#
4#
Fig. 33
Remove this wire before Fig. 34
connecting the Limit Switch

Three phase motor

1. Circuit diagram (See Fig. 36)

Fig. 35

20
2. Connection step (See Fig. 36)
a. The source wires (L1, L2, L3) connected with terminals of AC contactor marked
L1, L2, L3 respectively.
b. Terminals 4# of control button connected with wire 12# (brown wire) of limit
switch; wire 11# (blue wire) connected with A1 terminals of AC contactor, Earth
wire ( yellow and green wire) of limit switch is connected with terminal earth wire
of the motor.
C. Terminals 3# of control button connected with L1 terminals of AC contactor.

Fig. 36

21
IV. EXPLODED VIEW
Model 210C 210CX

Car in

Fig. 37

22
Cylinders

Fig. 38

MANUAL POWER UNIT

220V/50HZ/1Phase 380V/50HZ/3Phase

Fig. 39

23
 Illustration of hydraulic valve for hydraulic power unit
Manual power unit, 220V/50HZ, Single phase (See Fig. 40)

Running capacitor

Oil return port

Relief valve

Release valve

Handle for Release

Oil Outlet Throttle valve
valve

Check valve

Fig. 40

Manual power unit, 380V/50HZ, 3 phases (See Fig. 41)

Running capacitor

Oil return port

Relief valve
Release valve

Handle of release
Oil outlet valve
Throttle valve

Check valve

Fig. 41

24
V. TEST RUN
1. Adjust synchronous cable (See Fig. 42)
Use wrench to hold the cable fitting, meanwhile use
ratchet spanner to tighten the cable nut.
Make sure two cables are with the same tension Cable nut
so that two carriages can work synchronously.
Fit the plastic hole cover on the lifting carriages.
If the carriages does not synchronize when lifting,
Please tighten the cable nut of lower side carriage.
Fig. 42

2. Adjust safety cable

Lifting the carriages and lock at the same height, strain the safety cable and then
release a little, and then tighten the cable nuts. Make sure the safety device can
always be worked properly.
3. Bleeding air
This hydraulic system is designed to bleeding air by loosen Bleeding plug
the bleeding plug. Lifting the carriages to about 1 meter
height, and loose the bleeding plug, the air would be
bled automatically, then tighten the plug after bleeding,
the lift would work stably and smoothly,
otherwise repeat bleeding (See Fig. 43).
Fig. 43

4. Adjust the lower speed

You can adjust the lower speed of the lift if needing: Loosen the fixing nut of the
throttle valve, and then turn the throttle valve clockwise to decrease the lower speed,
or counterclockwise to increase the lower speed. Do not forget to tighten the fixing
nut after the lower speed adjustment has been done.

Fixing Nut Throttle Valve

Fixing Nut

Fig. 44

25
5. Test with load
After finishing the above adjustment, test the lift with load. Raise the lift in low

position for several times firstly, make sure the lift can be raised and lowered

synchronously, and the safety device can be locked and released synchronously. And

then raise the lift to the top position completely. If there is anything improper, repeat

the above adjustment.

NOTE: It may be vibrated when lifting at start, lifting it with load for several times,
the air would be bled and the vibration would be disappeared
automatically.

Fig. 45 Hydraulic System

26
VI. OPERATION INSTRUCTIONS
Please read the safety tips carefully before operating the lift
To lift vehicle
1. Keep clean of site near the lift;
2. Position lift arms to the lowest position;
3. To shortest lift arms;
4. Open lift arms;
5. Position vehicle between columns;
6. Move arms to the vehicle’s lifting point;
Note: The four lift arms must at the same time contact the vehicle’s lifting point

where manufacturers recommended

7. Push button UP until the lift pads contact underside of vehicle totally. Recheck to
make sure vehicle is secure;
8. Continue to raise the lift slowly to the desired working height, ensuring the balance
of vehicle;
9. Push lowering handle to lower lift onto the nearest safety. The vehicle is ready to
repair.
To lower vehicle
1. Be sure clear of around and under the lift, only leaving operator in lift area;
2. Push button UP to raise the vehicle slightly, and then release the safety device,
lower vehicle by pushing lowering handle.
3. Open the arms and position them to the shortest length;
4. Drive away the vehicle.
5. Turn off the power.

VII. MAINTENANCE SCHEDULE

Monthly:
1. Re-torque the anchor bolts to 150 Nm;
2. Check all connectors, bolts and pins to insure proper mounting;
3. Lubricate cable with lubricant;
4. Make a visual inspection of all hydraulic hoses/lines for possible wear or leakage;
5. Check safety device and make sure proper condition;
6. Lubricate all rollers and pins with 90wt. Gear oil or equivalent;
Note: All anchor bolts should take full torque. If any of the bolts does not function for

any reason, DO NOT use the lift until the bolt has been replaced.

27
Every six months:
1. Make a visual inspection of all moving parts for possible wear, interference or
damage.
2. Check and adjust as necessary, equalizer tension of the cables to insure level
lifting.
3. Check the vertical of columns.
4. Check rubber pads and replace as necessary.
5. Check safety device and make sure proper condition.

VIII.TROUBLE SHOOTING
TROUBLE CAUSE REMEDY

1. Button does not work 1. Replace button

2. Wiring connections are not in good 2.Repair all wiring connections

Motor does not condition

run 3. Motor burned out 3. Repair or replace motor

4. Height Limit Switch is damaged 4.Replace the Limit Switch

5. AC Contactor burned out 5. Replace AC Contactor

1. Motor runs in reverse rotation 1.Reverse two power wire

Motor runs but 2. Gear Pump out of operation 2.Repair or replace

the lift is not 3. Release Valve in damage 3. Repair or replace

raised 4. Relief Valve or Check Valve in 4.Repair or replace

damage 5.Fill tank

5. Low oil level

Lift does not 1. Release Valve out of work

stay up 2. Relief Valve or Check Valve leakage Repair or replace

3. Cylinder or Fittings leaks

1. Oil line is jammed 1. Clean the oil line

Lift raises slowly 2. Motor running on low voltage 2. Check electrical system

3. Oil mixed with Air 3. Fill tank

4. Gear Pump leaks 4. Replace Pump

5. Overload lifting 5. Check load

1. Safety device are locking 1. Release the safeties

Lift cannot lower 2. Release Valve in damage 2. Repair or replace

3. Safety cable broken 3. Replace

4. Oil system is jammed 4. Clean the oil system

28
IX. PARTS LIST FOR MODEL 210C 210CX
Qty.
Item Part# Description Note
210C 210CX
1 11209206 Power side Column 1 1
81513001/
201 Manual Power Unit 1 1
81513002
3 10209003 Hex Bolt 4 4
4 10209004 Rubber Ring 4 4
5 10209005 Self locking Nut 4 4
6 11206002 Safety Pin 2 2
7 10209007 Safety Spring 2 2
8 10209008 Safety Cover 2 2
9 10209009 Cup Head Bolt 4 4
10 10209010 Snap Ring 1 1
11 10620059 Protective ring 1 1
12 10209049 Plastic small pulley 3 3
13 10209012 Hair Pin 8 8
14 11209013 Power side Safety Lock 1 1
15 10206006 Washer 6 6
16 10206023A Hex Nut 2 2
17 11209014 Cylinder 2 2
17A 11209111 Protective ring for cylinder 2 2
18 10209015 Slider Block 16 16
19 10209016 Carriage Plastic Cover 2 2
20 11209208 Carriage 2 2
21 10209018 Protective Rubber 2 2
22 10209019 Screw 12 12
23 10206190 Tool tray 2 2
24 10209021 Hex Nut 4 4
25 10209022 Washer 12 12
26 10217044 Arm lock 4 4
27 11217046A Arm lock bar （left） 2 2
28 10206036 Hair Pin 4 4
29 10217045 Spring 4 4
30 11206191 Toe guard bar 4 4
31 11217046 Arm lock bar （right） 2 2
32A 11203146 Outer section arm 4 4
32B 11203147 Middle section arm 4 4
32C 11203148 Inner section arm 4 4

29
 Qty.
Item Part# Description Note
210C 210CX
33 11217168 Arm Pin 4 4
33A 10520023 Snap Ring 4 4
34 10206048 Socket Bolt 12 12
35 10209034 Lock Washer 18 16
36 10209033 Washer 18 16
37 11206049 Moon Gear 4 4
38 10209153 Pull tab for arm lock bar 4 4
39 10206032 Snap ring 4 4
40 10201002 Hex Bolt 14 12
41 10209039 Lock Washer 12 12
42 10201046A Rubber Pad Assy. 4 4
42A 10420138 Socket bolt 4 4
42B 10209134 Rubber Pad 4 4
42C 11680030B Rubber Pad support Frame 4 4
43 10206025A Foam Cushion for control bar 1 1
44 10201005 Split pin 2 2
45 11206025C Connecting Pin for Control Bar 2 2
46 11202011 Control Bar 1 1
47 11206042 Control Bar Bracket 2 2
48 10206041 Hex Bolt 4 4
49 10206023 Self locking Nut 4 4
50 10206013 Limit Switch 1 1
51 10206011 Cup Head Bolt 2 2
52 10209184 Wire Cable 1 1
11211011 1 0
53 Top Beam
11211011A 0 1
54 10209046 Hex Bolt 4 4
55 10209057A Bronze Bush 6 6
56 11209057 Small Pulley 4 4
57 10209056 Self locking Nut 2 2
58 11209207 Offside Column 1 1
59 11211013 Offside Safety Lock 1 1
60 11209051B Stackable Adapter(1.5″) 4 4
61 11209052B Stackable Adapter (2.5″) 4 4
62 11209053B Stackable Adapter (5″) 4 4
63 11209054A Stackable Adapter Bracket 2 2
64 10680003 Hex Bolt 6 6
65 11209044 Pin For Pulley 2 2
66 11209045 Big Pulley 2 2
67 10209059B Anchor Bolt 12 12
30
 67A 10620065 Shim 10 10
67B 10201090 Shim 10 10
Parts List for Oil Hose, Fitting & Cable
68 10209060 90° Fitting for power unit 1 1

69 10211014 Oil hose 1 1

70 10211016 T- fitting 1 1
71 10211015A Oil hose 2 1
71A 10211020 Oil hose 0 1
72 10211017 Extend 90° fitting for Cylinder 2 2
73 10209066 Hex Nut 4 4
10211018 2 0
74 Cable
10211018A 0 2
10211019 1 0
75 Safety Cable
10211019A 0 1
76 10209501B 1 0
Parts Box
77 10209502B 0 1
Parts for Cylinder
17-1 10209069 O-Ring 2 2
17-2 10209070 Bleeding Plug 2 2
17-3 10209071 Support Ring 2 2
17-4 10209072 Y-Ring 2 2
17-5 10209073 O-Ring 2 2
17-6 11209074 Piston 2 2
17-7 10209075 0-Ring 4 4
17-8 11209076 Piston Rod 2 2
17-9 11209077 Piston Rod Fitting 2 2
17-10 10209078 Dust Ring 2 2
17-11 11209079 Head Cup 2 2
17-12 10209080 O-Ying 2 2
17-13 11209081 Bore Weldment 2 2

31
PARTS LIST FOR MANUAL POWER UNIT
Parts For Manual Power Unit, 220V/50Hz/1 phase
Item Part# Description Qty. Note
1 71150019 AMGO Name plate 1
2 81400300 Cup Head Bolt 2
3 81400363 Motor Connecting Shaft 1
4 81400362 Manifold block 1
5 10209149 Washer 4
6 81400276 Iron plug 1
7 81400259 Red rubber plug 1
8 85090142 Lock Washer 4
9 81400292 Gear pump 1
10 81400294 Buffer valve 1
11 10209034 Washer 2
12 81400295 Socket bolt 2
13 81400365 O ring 1
14 10209152 Ties 1
15 85090167 Magnet 1
16 81400290 Filter 1
17 81400453 Motor 1
18 41030055 AC connector 1
19 81400088 Run capacitor 1
20 81400130 Start capacitor 1
21 10420148 Cup Head Bolt with washer 6
22 81400208 Cover of Motor Terminal Box 1
23 10420070 Push button 1
24 81400296 Nut 1
25 81400459 Throttle valve body 1
26 10209069 O ring 1
27 81400266 Relief valve 1
28 81400284 Iron plug 1
29 81400452 Oil Return Pipe 1
30 81400451 Hair pin 1
31 10209020 Plastic ball 1
32 81400125 Nut for release valve 1
33 81400124 Shim for release valve 1
34 81400450 Valve seat(high) 1
35 81400443 Release valve 1
36 81400267 Check valve 1
37 81400288 Inlet pipe 1
38 81400289 Oil return pipe 1
39 81400364 Hose clamp 1
40 81400263 Oil tank cap 1
41 81400275 Oil tank 1

32
Parts For Manual Power Unit 380V/50Hz/3 phase
1 71150020 AMGO Name plate 1
2 81400300 Cup Head Bolt 2
3 81400363 Motor Connecting Shaft 1
4 81400362 Manifold block 1
5 10209149 Washer 4
6 81400276 Iron plug 1
7 81400259 Red rubber plug 1
8 85090142 Lock Washer 4
9 81400292 Gear pump 1
10 81400294 Buffer valve 1
11 10209034 Washer 2
12 81400295 Socket bolt 2
13 81400365 O ring 1
14 10209152 Ties 1
15 85090167 Magnet 1
16 81400290 Filter 1
17 81400439 Motor 1
18 10420070 Push button 1
19 81400348 AC connector 1
20 81400286 Cover of Motor Terminal Box 1
21 10420148 Cup Head Bolt with washer 4
22 81400296 Nut 1
23 81400459 Throttle valve body 1
24 10209069 O ring 1
25 81400266 Relief valve 1
26 81400284 Iron plug 1
27 81400452 Hair pin 1
28 81400451 Handle For Release Valve 1
29 10209020 Plastic ball 1
30 81400125 Nut for release valve 1
31 81400124 Shim for release valve 1
32 81400450 Valve seat(high) 1
33 81400443 Release valve 1
34 81400267 Check valve 1
35 81400288 Inlet pipe 1
36 81400289 Oil return pipe 1
37 81400364 Hose clamp 1
38 81400263 Oil tank cap 1
39 81400275 Oil tank 1

33
 72121106

09/2018

34