Instruction Manual for Food Equipment Mixer Important: Please Read Before First Use! Guangdong Henglian Food Machine CO., LID Address: 95 Lijiang Road, Shilou, Panyu, Guangzhou China Tel: +86(20) 84868083 84868086 Fax: +86(20) 84862988INSTRUCTION MANUAL, TABLE OF CONTENTS Installation, : 3 eee EAs eee eae eee EE Components Identification, 4 Accessories Identification, 5 Technical Specification 6 Operations 7 eee SUE: MIXER INSfRUCTION MANUAL 3 Important Safeguards M20A Mixers complies with all safety requirements of UL standards for commercial Kitchen equipment & Canadian standards for Canada, M20A +S complies with NSF : SAVE THESE INSTRUCTION: td INSTALLATION 1. Unpack unit, accessories and instructional material carefully, 2. Check over equipment to make sure that there is not any damage to equipment. Nore: [equipment appears fo be camaged contact carrier within __ days from delivery 3. Please read all instruction carefully before operating equipment. 4, Pind a suitable operating area to install equipment, Note: Make sure there is edequete space around equipment to allow the user to properly ' operate controls and remave and install accessories, Do noi place machine in wet or danp area, 5. Lift equipment off ofthe floor to move, do not slide equipment across the floor. Note: Do not handle or lif equipment alone; use the help of others. 6 Consult an electrician to asswwe the electrical supply complies with specified ccurrent(amp) capacity, 7. Do not plug in the same outlet shared by other equipment. 8. Do not use extension cord, 9. Keep all accessories clean and in a sate place so they do not become scratched or misplaced 10. Do not expose the equipment to any moisture that may enter electrical box or components. 11. For safety purposes, do not remove any service covers, safety guards or warning labels.RINSTRUCTION MANUAL. 4 COMPONENTS IDENTIFICATION Figure A Stop Button - push to stop/turn to release Start Button - push to start Top Cover #12 Meat Grinder Attachment Hub — remove safety cover from #12 hub to attach accessory Speed Switch - controls th mixing speed Safety Guard - must be lowered into position during operation Mixing Shaft — mixing accessories are attached to the mixing shaft Bow! — holds mixing contents, Bow! Locks ~ secure bow! in place |. Base — rubber protection on bottom to prevent rusting, scratching and sliding Power Cord — plug into current compliant electrical outet Reset Button ~ press to reset unit incase of overload . Bow! Lever ~ raises and lowers bow, Operation Safety Switch ~ engages when bow is raised & locked into place,4 MIXER INSTRUCTION MANUAL ACCESSORIES IDENTIFICATION 1) Bow! - 20g, mixing bow! 2) Dough Hook - suitable for mixing flour in low speed mode 3) Flat Beater - suitable for mixing crushed powered in medium speed mode 4) Wire Whisk = 5) Meat Grinder ~ optional atachment — suitable for grinding meat table for mixing liquids in high speed mode 1). Bowl(20gt. Mixing bout!) Figure 2). Dough Hook{to use 3). Flat Beater (to use 4), Wire Vitisk (suitable for {ot mixing four) for mixing crushed powered) for mixing liquids) in low speed mode. medium speed. high speed Figure ¢ Figure D Figure € 5). Meat Grinder (optional) Figure FMIXER INSTRUCTION MANUAL. 6 TECHNICAL SPECIFICATIONS Note: Seleet speed according to specified accessory mode 1, Dough Hook - suitable for mixing flour and bread dough on the low speed mode Note; Mix should equal 45% to 50% of the flour weight (See Figure G) 2, Flat Beater - suitable for mixing crushed, powdered and pasty food, such ad stuffing on medium speed mode (See Figure H) 3. Wire Whip - suitable for mixing liquid food, such as cream, egg on high speed mode (See Figure D Figure & Figure H Model ] Bowi | Motor | Frequency | Power | MiningSpond | a Dimensions | Net Voiune Kneading Capcity Weight M20A ] 20q. | tphae | core | rnp | roorseaermm | sion — | agstraai~ | 230m = Figure JMIXER INSTRUCTION MANUAL a OPERATIONS 1. Make sure the equipment i properly installed 2. Attach accessory suitable for mixing needs to mixing shaft 7. Note: Be careful nat 10 scratch or damage the mixing bowl 8 when assembling accessories. 3. Secure the bowl using the bow! locks 9 on Both sides of bowl, 4, Pour contents into mixing bow! 8 5, Tuan bow! fever 13 clockwise into locked po Double check that afl steps have been completed 7. Tum speed switch to suggested speed for intended use 5. Note: For safety purpases, sop ait before changing speeds 8. Make sure stop button f is released 9. Plugin power cord 11 10, Press start button 2. 1. Before checking contents, press stop button 1. 12, guard 6 to check contents. rst wall a Note: A safety feature will turn off the machine if itis overloaded. Ifthis ocewrs few minutes and then press reset button 12. 13. This unit can work in the #12 mincer attachment, {f the user want it, please point out especially, and pay for it.M20A SERVICE MANUAL. PARTS LIST ‘The movement of the attachments is gear driven, There is enough lubrication in to the shift bbox, however, add lubrication to the gear box once every four months. Mike to send us a ‘maintenance sheet and service manuel. Uf service is required beyond daily maintenance refer to a qualified personal or call our service number located on the first & last page of this booklet, PARTS LIST A [Titus Part NO Name Of part AMT A. ‘Shift handle i L Principal axis L M20A-05-49) Handle seat i 2 Axis cover i M20A-05-47 | Eecentricity cover i 3 Joint gear 2-38 i M20A-05-08 Front cover, I 4 Gasket n M30A-05-13_| Twist tie-in seat i 5 Bless cover i M20A-05-02 ‘Lock bolt i 6 M20A-05-19 Clutch i TA3S302, Roll pin bearing i 7 M30A-08-16 Gear Z=: 1 T20A-05-35 Adjust gasket i 8 M20A-05-15 Big cone gear 2-46 r M20A-05-14 [Small cone gear Z=36 | 1 9. Small joint gear Z=29 [1 M20A-052 Airproof caver c 10 Axis cover i “40 M20A-05-37 | Annular sear Z=67 i 1 Zysospern r a1 | WI20A-05-35~ 1 Whip seat c 2 M20A-01 Top cover i 42 [204-050 Dil receiver i 13 M20A-05.06 Cover r 45 M204-05-38 [Planet sear Z=19 i 14 | M904-05-25 Bearing seat cover i aa] M204-05-39 Whipshe™ Pd 15_[ M2045. ‘Gear shalt Z=15 i as [M3013 | d 1 16 | M20A-05-22 Gear 2°35 i a6 | 0824 Bowl press plank 2 17 | M20A-05.26 Bash r 47 [M304-17 Slide rack i 18[M20A.05.97 Gear 2-35 i as [204.25 So se a, 2 19_[_M20A-05.05 ‘Cover i 49 [M087 Exist pole t Gear shit 217 i 30 [M007 Eade. 7 Worn wheel 7=29 r 31 M2001 Press plank 2 Back cover i 32 M20A-12, pri 1 Back cover plate C 3 M30A-09 ‘Comecting haul i Rotor module i Sa | w20A-06 Link awl T 5 ‘Worm busi r 35_[_w0A-19- Whip haul 1 ‘M20A.05-08 Wom i 36] MB0A-18 Mix ware o M20A-05-10 Box body i ‘57 M20A-20 i 08-05-16, Dial for axis i 38, M20A~ 0 MS0A-05=55 Dial fork, i 59 |“ M0a-27 t