All manuals and user guides at all-guides.

com

WHITE

WHITE
4 /1 1

m
.co
es
W 200

-U
uid

WHITE MODEL WW200 INSTRUCTION BOOK

-g
all

Call Toll Free 800-331-3164

www.whitesewing.com
All manuals and user guides at all-guides.com

NAME OF PARTS
Bobbin winding spindle
Thread pulling
bar Handwheel

Selector

screw
Stitch Length!
Reverse Switch

\Bobbin Cover

Handl Winding guide

/
Upper thread
guide(1)

Bobbin
spindle Presser Foot
Lever
Needle Shaft
Top Thread

Power switch

Foot ControEEE
C Adaptor’Jack
0 for top
Jack (DC 6V, 1OA) thread
All manuals and user guides at all-guides.com

ACCESSORIES
Bobbins Threader Needle Foot pedal

Top Thread Bobbin

protector
seat Top Thread
Holder

Note: All the accessories are in

snap-in sewing table.

Snap-in sewing table

1 .Take the snap-in sewing table out,
pull it out from the machine as
photo(1)
2.The bobbin and accessory
bag are put stored in the snap-in
sewing table.
Note: All the accessories are in snap-in
sewing table which can also be
available to store accessories when
you finish sewing.

Romove and replace the needle

is dangerous to replace the
needle when the power is on,
you must turn it off.
1 Make the power switch off.
2.Turn hand wheel until needle is in the
highest position, loosen the needle
clamp screw and remove the old
needle.
3.lnsert a new needle into the needle
• If the needle is incorrectly set ,the machine can clamp, make sure the flat side of the
not sew. needle is to the back, fitting correctly
• Tighten the needle clamp screw by turning it
clockwisely. If the needle is too loose, it will out
and tighten the needle clamp screw.
when you are sewing.

2
All manuals and user guides at all-guides.com

THREADING UPPER THREAD

&

Fig.3

Caution: Don’t touch the on/off switch when threading the upper thread.

linstall the top thread seat in the machine.(Fig 1)

2.Fix the top thread holder in the top thread seat, place the top thread
bobbin on the top thread holder with the bobbin protector 2mm away
from the bobbin (avoid pressing the top thread bobbin too tight to prevent
the thread bobbin from rotating, or itil cause weak sewing).
3.Guide the bobbin thread according to Fig 3 and Fig 4 thread following
,

the numbers 1-2-3-4-5-6 and thread the needle eye(7) from front to
back.
Note: Avoid guiding the top thread around winding guide to prevent bad
sewing.

3
All manuals and user guides at all-guides.com

THREADING THE LOWER BOBBIN

Fig.1 Fig.3 r
1
0
B
A

Fig.2 When threading the lower bobbin,

make sure the power switch is OFF.
SETTING LOWER THREAD:
1 .Slide the bobbin cover forward and take
itoff (Fig. 1)
2.Place the bobbin into the bobbin case
(NOTE: Be sure that the bobbin rotates
counter-clockwise when thread is pulled).
3.The bobbin thread pass through “A “to
“B”, leaving about 10 CM taH. (Fig. 3)
4.Slide bobbin cover back on.

DRAWING UP LOWER THREAD:

1 .Hold the end of the upper thread with your
left hand ,turn the hand wheel towards you
with your right hand
2.As you turn the hand wheel ,the needle goes
down. When the needle turns to the lowest
position, the hook of the bobbin case will
meet the upper thread, after the shuttle turns
a circle ,it will connect with the lower thread.
Turn the hand wheel counterclockwise again,
the lower thread will be drawn up.Hold the
lower thread ,pull the tail out ,put the upper
and lower threads under the presser foot,
toward the back of the needel leaving about
10CM aside.

4
 All manuals and user guides at all-guides.com

SEWING

Fig.1 Fig.2

m
.co
1. Turn the stitch selector dial to the stitch pattern you need.(See stitch pattern
selector on page 6)
es
2. Move the stitch length in the right position (See STITCH LENGTH
ADJUSTMENT).
3. Turn the hand wheel toward you to raise the needle to its highest position (Fig.
1). Raise the presser foot, and place the fabric under it.
4. Lower the presser foot and rotate hand wheel to place the needle into
fabric.(Fig .2)
uid

5. Plug the foot control and the adaptor into the jacks of the machine and turn
on the power switch, the light on, you can sew by pressing the foot control.
Press down the foot pedal, machine will begin sewing. Remove your foot and
the machine will stop sewing.(Fig.4)
6. If you finish sewing, remove the foot from the foot control to stop .Turn hand
wheel with your right hand to raise the needle to the highest position, and pull
out the upper thread leaving about 1 OCM(Fig 5), then raise the presser foot
and remove the fabric to the back.(Note: Don’t pull out the fabric roughly when
-g

it’s not easy to pull out ,the needle will bend or break.)
all

5
All manuals and user guides at all-guides.com

BOBBIN WINDING

1.1 emove the needle firstly, as illustrated in Fig 1 ,press down the winding lever
to raise the thread winding lever, and place the empty bobbin in the bobbin
winding lever.
2.Pull the upper thread out of the needle eye ,guide the thread through winding
guide to the empty bobbin, and wind thread counter clockwise around the empty
bobbin few circles
3.Turn the switch on, the winding starts .Turn off when the bobbin is full to stop
winding, and take away the bobbin from the bobbin winding bar.
4.Raise the winding lever to lower the thread winding lever.

Note: Avoid guiding the top thread into upper thread guide(1) to prevent weak
sewing.

STITCH PATTERN SELECTOR

J
Before sewing, please choose a suitable stitch pattern. The machine has seven
stitch patterns. As illustration shows, turn the stitch pattern dial to select the
pattern you need.
You can change stitch length after selecting the stitch pattern, and the stitch
pattern will be changed accordingly.

Note: Make sure the needle is in its highest position when adjust the pattern
dial, and do not adjust the pattern dial while sewing.

6
All manuals and user guides at all-guides.com

ADJUSTING THREAD TENSION

The correct stitch must be as Upper thread Fabric
illustration. The upper and lower
thread tension are equal and
strong enough to lock both threads
owerea
in center.
Fabric
PP thread

Lower

1. If the upper thread is too tight, the

lower thread will be pulled up tightly
to the fabric, and you will see the
upper stitch (The thread shown on
the surface of the fabric) To have
.

the fabric evenly sewn,balance the

tension by turing the thread tension
dial counterclockwise to the
balanced tension.
Fabric
Upper thread

Lower thread
2. If the upper thread too is loose, the
upper thread will be pulled up tightly
to the fabric, you will see the lower
stitch (The thread shown on the
bottom of the fabric). To have the
fabric evenly sewn, balance the
tension by turning the thread tension
dial clockwise to the balanced
tension.
7
All manuals and user guides at all-guides.com

STITCH LENGTH ADJUSTMENT

Before sewing your fabric, test with fabric
scraps to choose the stitch length you want.
The machine provides three stitch lengths.
As illustration shows, turn the stitch length
switch to the “—“for the longest stitch length
and on “——“ position, the dial for medium stitch
length, and position, the shortest stitch
“---“

length.

REVERSE
1. Reverse sewing is used to tie off stitches,
so they do not pull out. It is used at the
beginning and the end of seam.
2. When use reverse function,stop the
sewing, then put the reverse switch to
the right “fl” (As illustration shows) and
begin to sew.

Note: When reverse sewing, the sewing

length should not be more than 5CM.

8
All manuals and user guides at all-guides.com

CAUTION
1. Before operating the sewing machine, please read these
instructions completely.
2. Please use adapter ( DC 6V 1. OA).
3 Not suitable for the stretch and elastic fabric
4. If needle is bent I deformed, it will not work.
5. Make sure the flatside of the needle is toward the back, or it
will be not sew
6 When thread is tangled in the lower bobbin stop the machine
cut the tangled threads to clear bobbin case. Re-thread the
bobbin and draw up the bobbin thread.
7.Make sure the needle is correctly threaded from front to back.

9
 All manuals and user guides at all-guides.com

Problem Problem cause Amendment

No power
supply adaptor power inadequate
(or machine or output connecting the Use compatible adaptor
runs slowly) wrong polarity

Needle eye not in the middle Remove and reinsert a new needle
Skipping
stitches Needle bent Remove and insert a new needle
Presser foot too loose Tighten teh presser foot screw
Lower thread used up Replace with new lower bobbin

m
Bobbin thread
can’t be drawn
up Needle incorrectly threaded Threaded rightly. Make sure it is threaded from the
front to the back.

Thread blocked by lower Thread the upper thread and lower thread again
bobbin

.co
Breaking
thread Needle scarf too rough Remove and reinsert a new needle

Needle shank not seated in Insert the needle correctly

the upper end

Thread blocked by upper Pull out the spool pin and make the bobbin or thread
Stitches too bobbin run smoothly
loose or Upper thread too tight or
es
Adjust thread tension dial and make the stitches
uneven lower thread too loose sewn evenly
Needle bent or deformed Remove and reinsert a new needle

Presser foot too loose Remove and reinsert a new needle, tighten presser
foot screw
Breaking
needle Pull fabiic with force when
Remove and reinsert a new needle, and thread again.
uid

sewing
Needle not lowered into fabric Remove and reinsert a new needle, thread again,
when start sewing turn hand wheel to lower the needle into the fabric,
and then start sewing
-g
all

10