661 REMOTE CAR ALARM

USER INSTRUCTIONS
Proudly designed and engineered
in Australia by Dynamco Pty Ltd.

Congratulations on having one of the worlds most advanced

and unique Australian designed and engineered vehicle PROGRAMMING NEW REMOTE
security systems, installed in your vehicle! 1. Disarm the alarm by pressing the button #1.
2. Open the driver's door and leave door open.
3. Switch ignition switch Off and On 7 times.
IMPORTANT NOTICE: 4. When the 7th count is reached, leave ignition switch in the ON position.
Ensure your installer has programmed your individual PIN code before 5. Vehicle indicators will begin flashing when alarm is ready to accept new
taking your vehicle. (see “programming new PIN” section). remote codes.
6. Press button #1 on new remote control.
7. Test remotes by arming and disarming the alarm system.
BUTTON #1 OPTION SETTINGS
Arm/Disarm/Siren Stop Panic Passive Arm / Transmitter Code-Learning / Passive Lock / Ignition
a. Arming: During the arm procedure Lock &Unlock / Set Override PIN.
the siren chirps once, the indicators 1. Disarm the alarm by pressing button #1.
flash once, and the LED flashes slowly. 2. Open the driver's door and leave door open.
The siren will chirp three times if a door 3. Turn ignition switch On the number of times corresponding to the feature
is open while arming the system. you wish to alter. Refer to the Option Table for option selection number.
b. Triggering: The alarm system may 4. When the correct count is reached, leave ignition switch ON.
be triggered (except shock sensor) two 5. Vehicle indicators will flash when alarm is ready to change option.
seconds after the last door is closed. 6. Press button #1 on a valid remote control.
The shock sensor is active ten seconds 7. Alarm will flash vehicle indicators to confirm change, see option table for
after the last door is shut. one/three flash meaning.
c. Siren stop: When alarm siren is *** Warning this function can result in keys being locked in vehicle!!
sounding, press button #1 to stop the
siren sounding. The alarm will remain Ignition Switches Feature One flash Three flashes
armed. Press the lock button once more to disarm the alarm. 5 Passive arming Disabled Enabled
d. Disarm: During the disarm procedure the siren will chirp twice, the 6 Pasive lock Disabled Enabled
indicators will flash twice and the LED will flash quickly if passive arm is 7 Program new transmitter Press new remote control
enabled. 8 Ignition lock /unlock Disabled Enabled
e. Diagnostics: If the alarm has been triggered, when disarming, the siren 9 Set new PIN Begin changing PIN
will chirp four times and the indicators will flash four times (instead of
twice).
f. Lock/Unlock by remote: if the ignition switch is on, only the central EMERGENCY PIN OVERRIDE
locking will respond to the remote control. In the event a remote is lost, stolen or broken, the #661 may be overridden
g. Panic: Hold button #1 for longer than two seconds to sound the siren by using the programmed two digit Personal Identification Number (PIN).
and flash the indicators for thirty seconds. 1. Insert ignition key into vehicle ignition switch.
h. Re-arm: The alarm will auto arm & lock the doors in 30 seconds if the 2. Turn key to the ON position (the position just before engine crank). The
vehicle doors have not been opened since disarming. red status LED will glow constantly.
3. Return the key to the ACC position (the first position that powers your
BUTTON #2 radio).
One Time Mute Arm-Disarm/Car Locator/Boot Release 4. The status LED will begin flashing slowly. Count the flashes.
a. Temporary chirp disable: To disable the siren for one arm/disarm 5. When the flashes match the first number in your PIN, turn the ignition
procedure, press button #2 switch to the ON position again.
momentarily before pressing button 6. Repeat step #5 for the second digit of the PIN.
#1. The siren will still chirp three 7. The status LED will extinguish and the 661 will now be disarmed and
times if a door is left open. engine will start.
b. Car locator: Press button #2 for
longer than two seconds while the PROGRAMMING NEW PIN
alarm is armed to cause the siren to 1. Disarm the alarm by pressing button #1.
pulse and the indicators to flash for 2. Open the driver's door and leave door open.
five seconds. 3. Switch ignition switch Off and On 9 times.
c. Boot release: Press button #2 for 4. When the 9th count is reached, leave ignition switch ON.
longer then two seconds to disarm 5. Vehicle indicators will flash when alarm is ready accept new remote
the system and open the boot. The PIN.
vehicle indicators will flash four times 6. Press button #1 the number of times corresponding to the first digit of
to confirm boot release signal. the new PIN. Press button #2 the number of times corresponding to the
second digit of the new PIN.
7. Alarm will flash vehicle indicators three times to confirm successful
RE-ARM & RELOCK programming.
a. Relock: The alarm will rearm & relock the doors in 30 seconds if no doors
have been opened. This is to prevent accidental disarm. *** All central locking and boot release features require additional
b. Passive arm: the alarm will automatically arm after 30 seconds if the hardware, which is not supplied with the 661 alarm system. Vehicles with
ignition is turned off, then the doors are closed. This feature can be central locking and/or electronic boot release will still require connections
disabled. to the 661 which are not a part of a standard installation.
c. Passive lock: The alarm will automatically lock the doors 30 seconds
after the ignition is turned off and the last door is closed. This feature can
be enabled. Warning: Strongly recommended not to be used.
d. Anti Hi-jack: When enabled, the alarm will lock the doors four seconds
after the ignition switch is turned on. The alarm will unlock the door
immediately after the ignition is switched off. This feature will not activate
while the door is open.

Special Considerations:
Ensure the interior light of your vehicle is extinguished before
arming the 661. A fading dome light will “trick” the alarm into thinking
one of the doors is open during the arm cycle. An open door
warning is signalled by 3 chirps

Downloaded from www.Manualslib.com manuals search engine

 ENGINE IMMOBILISATION
When the system is armed the
engine is immobilised. The actual
point of immobilisation varies from
vehicle to vehicle, normally fuel and
starter motor are immobilised.

SPECIFICATIONS
Manufactured by Dynamco Pty Ltd
Model Number Cyclops 661
Supply voltage +12VDC ANNUAL INSPECTION
Current consumption < 10 mA Dynamco prides itself on the durability and integrity of its car security
systems. We welcome users to contact a Cyclops service centre every
BATTERY REPLACEMENT twelve months for an annual inspection. (Please note a charge may be
Using a small Phillips-head screwdriver, remove the screw(s) at the back levied for this inspection)
of the remote and carefully separate the two body housings taking take
care not to disturb the circuit board. Remove the old battery whilst paying WARRANTY TERMS & CONDITIONS
attention to the orientation of the positive and negative terminals. Insert The Dynamco range of Cyclops Security Systems is covered by an
new battery in identical fashion to the original and re-assemble remote. extensive warranty (See Below For Period). In the unlikely event of a faulty
Replace screw(s) and test remote control by pressing main button. For system Dynamco will either replace or repair the system at no cost during
further information, please contact your local Cyclops service centre. the detailed period. The warranty does allow for the following conditions ~
Remote battery type 23a. Subject to the conditions stated below, Dynamco Pty Ltd warranty the
product to be free from manufacturing defects and faulty material within
the warranty period stated.
PROBLEM SOLVING
· That the warranty registration has been completed in full at the time of
System won't activate when the door is opened
purchase / installation and is produced when warranty service is sought
- Make sure you have used the remote to set the system. It will not trigger if
· The warranty does not cover general maintenance such as cleaning /
the system has auto armed.
adjusting of door, boot, bonnet or any entry point switch, nor replacement
- Make certain the system is activated. LED should be flashing on the
of consumables items such as transmitter batteries, lighting circuit bulbs /
dashboard.
switches.
- Make sure that the interior dome light has not been left in the permanently
ON position.
The warranty shall be null & void if: -
- Make sure that you have allowed at least 10 seconds after setting the
1. Any person other than by an Authorised Cyclops Sales, Service &
system, before opening the door.
Installation Centre has repaired the product.
System won't activate or deactivate. LED won't flash or extinguish
2. Should a system / part defect become apparent within the warranty
- Make sure that ignition switch is in the OFF position.
period DYNAMCO PTY LTD will repair the product free of charge for parts
- Make sure the vehicle battery is not flat.
and labour. The warranty does not cover service labour content or mobile
- Try your spare remote transmitter unit.
service content.
The remote fails to operate
3. The product has been altered or tampered with in any way, or the
If the remote fails to operate and the LED does not light up when the button
serial number altered, defaced or removed.
is pressed then change the battery. To do this you will need a small Philips
4. The defect has been caused by negligence by the owner or their
head screwdriver. (See Battery Replacement)
agent / third party.
5. The product has not been operated correctly, installed by an
MANUFACTURER’S HISTORY
unauthorised Cyclops installer or has been subjected to misuse or undue
Dynamco has been involved in
wear and tear
the science of electronic vehicle
6. Siren, control module, remote controls or any other system part are
security technology for over 12
damaged by water.
years. From small beginnings
The warranty does not cover the following costs: -
Dynamco has grown steadily to
7. Transport of the product to and from Cyclops Service Centres.
become one of the world’s
8. Insurance of the product whilst in transit to or from the Cyclops
leading specialist companies in
Service Centres
electronic vehicle security,
9. Cost of any service call / labour where the product is found by Cyclops
designing and customizing
to be in good working order The benefits conferred by this Warranty are in
systems to combat the
addition to all other rights and remedies, which the consumer has
increasingly sophisticated
conferred in law.
professional car thief without
compromising the user friendliness of the systems. Systems are exported
No liability is accepted for any loss, loss from, damage to or inability to use
all over the world, it is easy to name drop when your customer list is so
the vehicle to which the system is installed.
impressive. Recently add to the list of BMW & Honda in Hong Kong, Toyota
Indonesia, the FBI in the USA, Australia's largest Hyundai dealer,
Australia’s largest Mitsubishi dealer, as well as AMWAY of New Zealand.
Government departments all over Australia, including the West Australian
Police Force plus hundreds of thousands of motorists world wide have
learned to rely on the sophistication and reliability and effectiveness of
WARRANTY REGISTRATION
MUST BE COMPLETED BY RETAILER AT TIME OF INSTALLATION
Dynamco’s electronic vehicle security systems Each working day over
1000 of systems are installed somewhere in the world, from Perth to Paris, DATE OF INSTALL’ :
from Sydney to Seattle. Dynamco pioneered Radio Frequency
Identification Systems and Random Encryption Technology (Code PURCHASED FROM :
Hopping). Both techniques now being fundamental to the majority of
vehicle security systems installed worldwide. Dynamco is cognisant of the OWNER’S NAME :
stringent requirements of vehicle electronics and the extremely hostile
environment to which the equipment is subjected. All Dynamco designs
therefore take these and many other factors into consideration. In 1990
TYPE OF VEHICLE :
Dynamco won the prestigious Australian Design Award but we haven’t
rested on our laurels. Our engineers keep Dynamco at the cutting edge of VEHICLE REGO’ :
electronic vehicle security.
WARRANTY PERIOD :
A) CONTROL MODULE ONLY :
OVERRIDE PIN NUMBER: __ __ B) REMOTE CONTROLS
AND SIREN :
AUTHORISED BY
SIGNED :

Downloaded from www.Manualslib.com manuals search engine