High Resolution Linear Gauge Sensor

HS-3412/3425
High Resolution Digital Gauge Counter

HG-4370

■ Best suitable as a high precise positioning detector because of high accuracy

(±0.5µm) and high resolution (±0.05µm)
■ Proof structure against dust (Protection class: IP50 of environmental resistance)
■ Large size LEDs (Character height: 14mm) as displaying device are used for
easy data reading.
■ Various function of offset/peak hold (MAX., MIN., RANGE)/multiplying and
selection of resolution (0.05µm/0.1µm/0.5µm)
HS-3412/3425 High Resolution Linear Gauge Sensor Unit : mm
HS-3412 HS-3425 HS-3412 HS-3425 Signal cable (Approx. 2 meter)
Measuring range 12 mm 25 mm Signal cable (Approx. 2 meter)
External drawing External drawing 46
46
Resolution 0.05 µm

φ4
Displaying accuracy (at 20°C) ±0.5 µm

φ4

41
41
Measurement force (at downward) 0.6N
Connector
Protection class IP50 Connector
39.4
8.5
17.2
Stem Diameter φ8 h 6 mm 39.4
17.2 8.5
Max. spindle speed* 0.2 m/s
Power supply 5DVC

89.5
Consumption current 20 mA Max.

66
Fixing hole for release Fixing hole for release
Operating temperature 0 to 40°C

(27.6) (17.5)

(17.5)
Cable length Approx. 2 meter

(24.7)
20.5
(4.5) (4.5)

3.5
φ8h6

3.5
(37.2)
33
Weight Approx. 200g Approx. 220g

(53.4)
50.5
Finger lift

(7.5)
(Accessory) φ8h6
Accessories Finger lift, Pin to replace the contact tip

76
Protection pin for preventing
Finger lift

(7.5)
from rotating when the
Spindle protection cap contact tip is replaced. (Accessory) Protection pin for preventing

(5.9)
30 from rotating when the
Insert hole (φ1.6) contact tip is replaced.
* It is maximum spindle speed when it is combined with exclusive counter of φ8 Position of rotating direction 30

(5.9)
is unfixed. Insert hole (φ1.6)
model HG-4370. φ8 Position of rotating direction
is unfixed.

HG-4370 High Resolution Digital Gauge Counter Unit : mm

■ Suitable sensor: Model HS-3412/3425 ■ RS-232C Interface
HG-4370
2-Phase difference signal, Sine waveform For data printing by DPU-414 exclusive printer and data External drawing
communication with personal computer
■ Displaying section 144 180 (11.5)
Based on the EIA-RS-232C.
MAIN Displaying device 7-segment LED (Red color) Baud rate 2400/4800/9600 bps

72
Character height 14 mm
SUB Displaying device LCD module ■ General Specification
No. of displayed characters 16-character x 2 lines Consumption current 1A Max. (at 9VDC) MAX4

(9.5)
STATUS Displaying the comparator result Operating temperature 0 to 40°C
UPPER (Red), OK (Green), LOWER (Red) Outer dimensions 144(W) x 72(H) x 180(D) mm
Weight Approx. 1.5 kg

+0.5
■ Function

0
68
Selectable of resolution Switchover at 0.05µm, 0.1µm, 0.5µm ■ Accessories Option
Multiplying Setting range : x 0.000001 to 9.99999 Exclusive AC power adaptor 1 pc. 138
+0.5
0

Offset Measurement range : ±9999999 Stand foot 1 set Rear View Panel cutout dimension
Peak hold MAX., Min., RANGE (MAX.–MIN.) Rubber foot 1 set
Comparator LO : LOWER set value Measurement value Socket for terminal 1 pc. (10-pin) SH-022
OK : LOWER set value < Measurement value External drawing
< UPPER set value ■ Options Cable
UP : UPPER set value Measurement value SH-022 Gauge stand
fixture
Attachment
Signal output by photo coupler DPU-414 Exclusive digital printer (Signal cable to connect Knob (C) for φ8 to φ10 hole
Max. capacity : DC30 V, 40mA HG-4370 is provided as standard accessory.) f25 Moving the support frame 78.5
at upper/lower. 60
Renewal time : Less than 30 ms AX-5022 RS-232C Cable Knob (B)
Fixing the
AA-3301 Panel mount fixture support frame
■ Control by external signal AA-813 Mechanical release
Support frame

Specification Voltage input : Hi level: +4 to +5.25 V

215
AA-916 Air release Knob (A)

0 to 115
of input signal Lo level: 0 to +1 V Fixing the sensor
80 Measurement 85
table
Non-contact input : Open-circuit voltage ; 5.25V Max.
Short-circuit current ; 1mA Max 60
30

Input signal logic : Negative logic (Lo level or contact-close) SH–022 GAUGE STAND

100 160
Type of signal : Reset, Hold, Comparator, Peak hold

■ External signal input ■ Connection to sequencer

Recommended interface Recommended interface
The following circuit is recommended as the interface for the external signal input of The following circuit is recommended as the interface for the external signal input of
RESET, HOLD, COMPARATOR, PEAK HOLD. COMPARATOR.

HG-4370 HG-4370 External control equipment,

Hi level : +4 to +5.25 V LO, OK, UP sequencer unit etc. Signal output by photo coupler
Voltage input
External control +5V +5V Lo level : 0 to +1 V Photo (No.7,8,9pin) Max. capacity : DC30 V, 40mA
equipment transistor
Open-circuit voltage : 5.25V Max.
6.8kΩ Non-contact input
Short-circuit current : 1mA Max Comparator function is working as following.
2.2kΩ LO : LOWER set value Measurement value
Non-contact Negative logic
voltage signal Input signal logic (Lo level or contact-close) OK : LOWER set value < Measurement value
etc. COM Register
(No.10pin) < UPPER set value

COM UP : UPPER set value Measurement value

External power ( + ) COM
supply DC24V (–)
COM
COM
Please be careful of polarity of the power supply.

* Outer appearance and specifications are subject to change without prior notice.
URL: http://www.onosokki.co.jp/English/english.htm
U.S.A. & CANADA P.R.CHINA WORLDWIDE
Ono Sokki Technology Inc. Ono Sokki Beijing Office Ono Sokki Co., Ltd.
2171 Executive Drive, Suite 400 Beijing Jing Guang Center 3510 1-16-1 Hakusan, Midori-ku,
Addison, IL. 60101 U.S.A. Hu Jia Lou, Chao Yang Qu Yokohama 226-8507, Japan
Phone : 630-627-9700 Beijing P.R.C. 100020 Phone: 045-935-3976
Fax : 630-627-0004 Phone : 010-6597-3113 Fax : 045-930-1906
URL : http://www.onosokki.net Fax : 010-6597-3114 E-mail: overseas@onosokki.co.jp
E-mail : info@onosokki.net E-mail : onosokki@public.bta.net.ch

Recycled Paper CAT. NO. 040904-01 Printed in Japan 04Y (SK) 2K