E2

POLYWED SUPERCOAT 500

A NON-TOXIC SOLVENT FREE HIGHBUILD, PROTECTIVE EPOXY RESIN COATING

EPOXY RESIN COATING NON TOXIC

SUPER COAT 500 is a solvent free,non-toxic;high build epoxy resin protective coating with
outstanding chemical and mechanical properties.SUPERCOAT 500 is supplied as a two
component in pre-weighted base and hardener packs, ready for site mixing.

APPLICATION TE C H NI C AL P RO P E RTI E S

SUPERCOAT 500 is designed for internal application such as: Mixed density at 250C: 1.5/cm3
Heavy duty protective coating for concrete and steel. Internal
protective lining for potable water concrete or steel tanks. Heavy Working life at 25°C: 30 minutes
duty wall and floor coating in food processing plants, grain silos,
dairies, breweries, hospitals, and pharmaceutical industries. High Tack free time at 35°C: Approx. 4 hours
chemical resistant protective coating for power stations,oil refineries,
and sewage treatment plants.
Cure (by compressive >4N/mm² at 12 hours
ADVANTAGES
strength) at 25°C: >65N/mm² at 4 days
 Approved for use in contact with potable water. Excellent
resistance to mould and fungus growth. Excellent resistance to
Coverage: 0.29 - 0.40kg / m² / coat
avariety of chemicals.
 Easy to clean with a smooth,hardand glossy finish. Non-toxic.
Finished film thickness: 180-240 microns per coat
 Exhibits good mechanical properties. Resistant to sewage
effluents.
In excess of the cohesive
Bond to concrete:
STANDARDS strength of concrete

SUPERCOAT 500 complies with the requirements of BS6920:2000

Full cure: After 7 days @ 25˚C
CLEANING
NO TE S
All tolls should be cleaned immediately after application using
SUPERCOAT 500 should not be applied over existing coatings.
POLYWED Solvent. Hardened materials must be cleaned
But it can be applied on top of itself, by maintaining the mentioned
mechanically.
recoatable time. Application should not be under taken if the tempera-
tureis below 5˚C, nor when the relative humidity exceeds 90%.
PACKAGING
Application should not be done, when there is standing or
SUPERCOAT 500 is available in 5 kg and15 kg packs.
runningwater.
STO RAGE
SUPERCOAT 500 is not color stable when exposed to direct
sunlight nor when in contacted with some chemicals. However this
SUPERCOAT 500 has a shelf life of 12 months if stored in dry
conditions at room temperature in original un opened packs.
Precaution is recommended if the application is Taking place at
If these conditions are not met, POLYWED technical department
high temperatures (above30˚C).
should be contacted for advice.

Page 1 of 2

+966 2 624 5984 +966 2 624 6160 www.polywed.com.sa info@polywed.com.sa 920009671

E2
POLYWED SUPERCOAT 500
A NON-TOXIC SOLVENT FREE HIGHBUILD, PROTECTIVE EPOXY RESIN COATING

M ETHOD OF U SE C AU TI O N

Substrate preparation: Healthand Safety:

Concretesurfaces: SUPERCOAT 500 should not come in contacted with skinor eyes.
The substrate should be sound,clean and free from contamination. Goggles and gloves should be used. In case of accidental contact
Surface laitance should be removed by grit blasting or water jetting. with eyes, imme- diately flush with plenty of water for at least 10
All exposed blow holes should be filled with epoxy Paste using minutes and seek medical advice if necessary.
EPOXY POLYPUTTYSteel surfaces:
All surfaces should be grit blasted to reach a bright finish meeting the
requirement of Swedish standard SA21/2.

Mixing:
To ensure proper mixing,a mechanically powered mixer or drill
fitted with suitable paddle should be used. Stir the content of each
component separately to disperseany settlement. Add the entire
content of the hardener to the base and mix for 3 minutes and until
uniform color and consistency are achieved.

Application:
SUPERCOAT 500 can be applied by roller. The first coat should
be applied to obtain a continuous uniformcoating.The second
coat should be applied within the overcoating time to achieve the
maximum adhesion between the two coats.

5 15 05
45
KG KG 12 C

LEGAL DISCLAIMER: Polywed endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising

Data sheets are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the
latest updated of the technical Data Sheets.

Page 2 of 2

+966 2 624 5984 +966 2 624 6160 www.polywed.com.sa info@polywed.com.sa 920009671