HSS END MILLS

Suitable for general-purpose operation slotting, drilling, profiling.

Good performance in machining General Steel, Stainless Steel,
Aluminum, non ferrous meterials Finishing Cutter, Roughing Cutter
 HSS END MILLS
SELECTION GUIDE

HSS Co8, 2 FLUTE, REGULAR LENGTH E 225

E2401
HSS Co8, ,

HSS Co8, 2 FLUTE, LONG LENGTH E 227

E2406
HSS Co8, ,

HSS Co8, 2 FLUTE, EXTRA LONG LENGTH E 228

E2749
HSS Co8, ,

HSS Co8, 2 FLUTE, SHORT LENGTH E 229

E2420
HSS Co8 ,

HSS Co8, 4 FLUTE, REGULAR LENGTH, CENTER CUTTING E 232

E2412
HSS Co8,

HSS Co8, 4 FLUTE, LONG LENGTH, CENTER CUTTING E 234

E2659
HSS Co8,

HSS Co8, 4 FLUTE, EXTRA LONG LENGTH E 235

E2750
HSS Co8,

HSS Co8, 4 & 6 FLUTE, SHORT LENGTH E 236

E2421
HSS Co8, 4 & 6 ,

HSS Co8, 2 FLUTE, REGULAR LENGTH, BALL NOSE E 239

E2480
HSS Co8, 2 ,

HSS Co8, 4 & 6 FLUTE, SHORT LENGTH, BALL NOSE E 240

E2410
HSS Co8, 4 & 6 , ,

HSS Co8, 4 & 6 FLUTE, LONG LENGTH, BALL NOSE E 240

E2429
HSS Co8, 4 & 6 , ,

HSS Co8, 2 FLUTE for ALUMINUM E 243

E2464
HSS Co8,

E 221
 HSS END MILLS
SELECTION GUIDE

E2461. E2462 HSS Co8, 50 HELIX E 244

E2463 HSS Co8,

HSS Co8, 2 FLUTE TAPER E 247

E2682
HSS Co8, ,

HSS Co8, 4 FLUTE TAPER E 249

E2683
HSS Co8, ,

HSS Co8, MULTI FLUTE, SHORT LENGTH, CENTER CUT ROUGHING-COARSE E 250
E2760
HSS Co8,

HSS Co8, MULTI FLUTE, LONG LENGTH, ROUGHING-COARSE E 251

E2759
HSS Co8,

E2751 HSS Co8, 3 FLUTE, SHORT LENGTH, ROUGHING-COARSE E 252

E2764 HSS Co8,

E2752 HSS Co8, 3 FLUTE, LONG LENGTH, ROUGHING-COARSE E 253

E2765 HSS Co8, , ,

HSS Co8, 3 FLUTE, SHORT LENGTH, ROUGHING for ALUMINUM-COARSE E 254

E2755
HSS Co8, ,

HSS Co8, 3 FLUTE, LONG LENGTH, ROUGHING for ALUMUNUM-COARSE E 255

E2756
HSS Co8, ,

E 222
 HSS END MILLS
SELECTION GUIDE

HSS Co8, MULTI FLUTE, SHORT LENGTH, ROUGHING-FINE E 256

E2753
HSS Co8,

HSS Co8, MULTI FLUTE, LONG LENGTH, ROUGHING-FINE E 257

E2762
HSS Co8,

HSS Co8, MULTI FLUTE, SHORT LENGTH, ROUGHING & FINISHING E 262
E2754
HSS Co8,

HSS Co8, MULTI FLUTE, LONG LENGTH, ROUGHING & FINISHING E 263
E2768
HSS Co8,

HSS Co8, 3 FLUTE, SHORT LENGTH, ROUGHING & FINISHING E 264

E2766
HSS Co8, ,

HSS Co8, 3 FLUTE, LONG LENGTH, ROUGHING & FINISHING E 265

E2767
HSS Co8, ,

HSS Co8, MULTI FLUTE, SHORT LENGTH, ROUGHING BALL NOSE-COARSE E 268
E2806
HSS Co8,

E 223
 HSS END MILLS
SELECTION GUIDE

HSS Co5, 1 FLUTE for ALUMINUM E 270

EL612
HSS Co5, ,

HSS Co5, 1 FLUTE E 271

EL623
HSS Co5,

HSS Co8, MULTI FLUTE, SHELL E 272

E2675
HSS Co8,

HSS Co8, MULTI FLUTE, SHELL for ALUMINUM E 273

E2676
HSS Co8,

HSS Co8, MULTI FLUTE, ROUGHING SHELL - COARSE E 275

E2677
HSS Co8,

HSS Co8, MULTI FLUTE, ROUGHING SHELL - FINE E 276

E2678
HSS Co8,

HSS Co8, MULTI FLUTE, ROUGHING & FINISHING SHELL E 277

E2679
HSS Co8,

HSS Co8, 4 FLUTE, CORNER ROUNDING CUTTERS E 279

E2498
HSS Co8, ,

E 224
 HSS Co8, 2 FLUTE, REGULAR LENGTH
HSS Co8, ,

HSS
Co8 30 PLAIN p.E230, 231
These end mills are furnished as regular with right-hand
cutting and right-hand helical flutes. These are designed for
slotting, drilling, pocketing and general-purpose operation.

PLAIN SHANK E2401 Series Unit : mm

EDP No. EDP No. d EDP No. EDP No. d

D I L D I L
PLAIN TiAIN h6 PLAIN TiAIN h6

E2401010 EQ401010 1 6 2.5 55 E2401150 EQ401150 15 16 40 105

E2401015 EQ401015 1.5 6 4 55 E2401160 EQ401160 16 16 40 105
E2401020 EQ401020 2 6 6 55 E2401170 EQ401170 17 16 40 105
E2401025 EQ401025 2.5 6 7 55 E2401180 EQ401180 18 16 40 105
E2401030 EQ401030 3 6 10 55 E2401190 EQ401190 19 20 45 115
E2401035 EQ401035 3.5 8 12 60 E2401200 EQ401200 20 20 45 115
E2401903 EQ401903 4 6 12 55 E2401210 EQ401210 21 20 45 115
E2401040 EQ401040 4 8 12 60 E2401220 EQ401220 22 20 45 115
E2401045 EQ401045 4.5 8 15 65 E2401230 EQ401230 23 25 50 125
E2401905 EQ401905 5 6 15 60 E2401240 EQ401240 24 25 50 125
E2401050 EQ401050 5 8 15 65 E2401250 EQ401250 25 25 50 125
E2401055 EQ401055 5.5 8 15 65 E2401260 EQ401260 26 25 50 125
E2401907 EQ401907 6 6 15 60 E2401270 EQ401270 27 25 55 125
E2401060 EQ401060 6 8 15 65 E2401280 EQ401280 28 25 55 125
E2401065 EQ401065 6.5 10 20 75 E2401290 EQ401290 29 25 55 125
E2401909 EQ401909 7 8 20 70 E2401300 EQ401300 30 25 55 125
E2401070 EQ401070 7 10 20 75 E2401310 EQ401310 31 32 60 145
E2401075 EQ401075 7.5 10 20 75 E2401320 EQ401320 32 32 60 145
E2401911 EQ401911 8 8 20 70 E2401330 EQ401330 33 32 60 145
E2401080 EQ401080 8 10 21 75 E2401340 EQ401340 34 32 60 145
E2401085 EQ401085 8.5 10 25 80 E2401350 EQ401350 35 32 60 145
E2401090 EQ401090 9 10 25 80 E2401360 EQ401360 36 32 65 150
E2401095 EQ401095 9.5 10 25 80 E2401370 EQ401370 37 32 65 150
E2401100 EQ401100 10 10 26 80 E2401380 EQ401380 38 32 65 150
E2401105 EQ401105 10.5 12 30 90 E2401390 EQ401390 39 32 65 150
E2401110 EQ401110 11 12 30 90 E2401400 EQ401400 40 32 65 150
E2401115 EQ401115 11.5 12 30 90 E2401420 EQ401420 42 42 70 160
E2401120 EQ401120 12 12 31 90 E2401450 EQ401450 45 42 70 160
E2401130 EQ401130 13 12 35 95 E2401460 EQ401460 46 42 75 160
E2401916 EQ401916 14 12 35 95 E2401480 EQ401480 48 42 75 165
E2401140 EQ401140 14 16 35 100 E2401500 EQ401500 50 42 75 165

MILL DIAMETER
6 8 10 12 OTHER SIZE D : MILL DIAMETER
d : SHANK DIAMETER
TOLERANCE l : LENGTH OF CUT
L : OVERALL LENGTH

E 225
 HSS Co8, 2 FLUTE, REGULAR LENGTH
HSS Co8, ,

HSS
Co8 30 PLAIN p.E230, 231
These end mills are furnished as regular with right-hand
cutting and right-hand helical flutes. These are designed for
slotting, drilling, pocketing and general-purpose operation.

PLAIN SHANK E2401 Series Unit : mm

EDP No. EDP No. d EDP No. EDP No. d

D I L D I L
PLAIN TiAIN h6 PLAIN TiAIN h6

E2401011 EQ401011 1.1 6 3 55 E2401036 EQ401036 3.6 8 12 60

E2401012 EQ401012 1.2 6 3 55 E2401037 EQ401037 3.7 8 12 60
E2401013 EQ401013 1.3 6 3.5 55 E2401038 EQ401038 3.8 8 12 60
E2401014 EQ401014 1.4 6 3.5 55 E2401039 EQ401039 3.9 8 12 60
E2401015 EQ401015 1.5 6 4 55 E2401041 EQ401041 4.1 8 15 65
E2401016 EQ401016 1.6 6 4 55 E2401042 EQ401042 4.2 8 15 65
E2401017 EQ401017 1.7 6 5 55 E2401043 EQ401043 4.3 8 15 65
E2401018 EQ401018 1.8 6 5 55 E2401044 EQ401044 4.4 8 15 65
E2401019 EQ401019 1.9 6 6 55 E2401904 EQ401904 4.5 6 15 60
E2401021 EQ401021 2.1 6 7 55 E2401045 EQ401045 4.5 8 15 65
E2401022 EQ401022 2.2 6 7 55 E2401046 EQ401046 4.6 8 15 65
E2401023 EQ401023 2.3 6 7 55 E2401047 EQ401047 4.7 8 15 65
E2401024 EQ401024 2.4 6 7 55 E2401048 EQ401048 4.8 8 15 65
E2401025 EQ401025 2.5 6 7 55 E2401049 EQ401049 4.9 8 15 65
E2401026 EQ401026 2.6 6 10 55 E2401051 EQ401051 5.1 8 15 65
E2401027 EQ401027 2.7 6 10 55 E2401052 EQ401052 5.2 8 15 65
E2401028 EQ401028 2.8 6 10 55 E2401053 EQ401053 5.3 8 15 65
E2401029 EQ401029 2.9 6 10 55 E2401054 EQ401054 5.4 8 15 65
E2401031 EQ401031 3.1 8 12 60 E2401906 EQ401906 5.5 6 15 60
E2401032 EQ401032 3.2 8 12 60 E2401055 EQ401055 5.5 8 15 65
E2401033 EQ401033 3.3 8 12 60 E2401056 EQ401056 5.6 8 15 65
E2401034 EQ401034 3.4 8 12 60 E2401057 EQ401057 5.7 8 15 65
E2401902 EQ401902 3.5 6 12 55 E2401058 EQ401058 5.8 8 15 65
E2401035 EQ401035 3.5 8 12 60 E2401059 EQ401059 5.9 8 15 65

Unit : mm

MILL DIAMETER
from 1.1 to 5.9 D : MILL DIAMETER
d : SHANK DIAMETER
TOLERANCE l : LENGTH OF CUT
L : OVERALL LENGTH

E 226
 HSS Co8, 2 FLUTE, LONG LENGTH
HSS Co8, ,

HSS
Co8 30 PLAIN p.E230, 231
Possible for deeper & wider cutting by using the
much longer flutes.

PLAIN SHANK E2406 Series Unit : mm

EDP No. EDP No. d EDP No. EDP No. d

D I L D I L
PLAIN TiAIN h6 PLAIN TiAIN h6

E2406030 EQ406030 3 6 15 60 E2406230 EQ406230 23 25 90 165

E2406901 EQ406901 4 6 20 65 E2406240 EQ406240 24 25 90 165
E2406902 EQ406902 5 6 25 70 E2406250 EQ406250 25 25 90 165
E2406050 EQ406050 5 8 25 75 E2406260 EQ406260 26 25 90 165
E2406903 EQ406903 6 6 25 70 E2406270 EQ406270 27 25 90 165
E2406060 EQ406060 6 8 25 75 E2406280 EQ406280 28 25 90 165
E2406070 EQ406070 7 10 35 90 E2406290 EQ406290 29 25 90 165
E2406080 EQ406080 8 10 35 90 E2406300 EQ406300 30 25 90 165
E2406090 EQ406090 9 10 45 100 E2406310 EQ406310 31 32 95 180
E2406100 EQ406100 10 10 45 100 E2406320 EQ406320 32 32 95 180
E2406110 EQ406110 11 12 55 115 E2406330 EQ406330 33 32 100 185
E2406120 EQ406120 12 12 55 115 E2406340 EQ406340 34 32 100 185
E2406130 EQ406130 13 12 55 115 E2406350 EQ406350 35 32 100 185
E2406140 EQ406140 14 16 55 120 E2406360 EQ406360 36 32 105 190
E2406150 EQ406150 15 16 65 130 E2406370 EQ406370 37 32 105 190
E2406160 EQ406160 16 16 65 130 E2406380 EQ406380 38 32 105 190
E2406170 EQ406170 17 16 65 130 E2406390 EQ406390 39 32 110 195
E2406180 EQ406180 18 16 65 130 E2406400 EQ406400 40 32 110 195
E2406190 EQ406190 19 20 75 145 E2406420 EQ406420 42 42 115 200
E2406200 EQ406200 20 20 75 145 E2406450 EQ406450 45 42 120 205
E2406210 EQ406210 21 20 75 145 E2406480 EQ406480 48 42 125 215
E2406220 EQ406220 22 20 75 145 E2406500 EQ406500 50 42 125 215

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA.
TOLERANCE D : MILL DIAMETER
d : SHANK DIAMETER
h6 l : LENGTH OF CUT
L : OVERALL LENGTH

E 227
 HSS Co8, 2 FLUTE, EXTRA LONG LENGTH
HSS Co8, ,

HSS
Co8 30 PLAIN p.E230, 231
Possible for deeper & wider cutting by using the much
longer flutes than E2406(C2OLS) type.

PLAIN SHANK E2749 Series Unit : mm

EDP No. EDP No. d EDP No. EDP No. d

D I L D I L
PLAIN TiAIN h6 PLAIN TiAIN h6

E2749160 EQ749160 16 16 100 160 E2749300 EQ749300 30 25 120 200

E2749180 EQ749180 18 16 100 180 E2749906 EQ749906 30 25 150 250
E2749200 EQ749200 20 20 100 180 E2749907 EQ749907 30 25 200 280
E2749901 EQ749901 20 20 120 200 E2749320 EQ749320 32 32 150 230
E2749902 EQ749902 20 20 150 230 E2749908 EQ749908 32 32 200 280
E2749220 EQ749220 22 20 120 200 E2749350 EQ749350 35 32 150 250
E2749240 EQ749240 24 25 100 180 E2749909 EQ749909 35 32 200 300
E2749903 EQ749903 24 25 150 250 E2749360 EQ749360 36 32 150 250
E2749250 EQ749250 25 25 100 180 E2749380 EQ749380 38 32 150 250
E2749904 EQ749904 25 25 120 220 E2749400 EQ749400 40 32 150 250
E2749905 EQ749905 25 25 150 250 E2749910 EQ749910 40 32 200 300
E2749260 EQ749260 26 25 150 250 E2749450 EQ749450 45 42 200 300
E2749280 EQ749280 28 25 150 250 E2749500 EQ749500 50 42 200 300

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA.
TOLERANCE D : MILL DIAMETER
d : SHANK DIAMETER
h6 l : LENGTH OF CUT
L : OVERALL LENGTH

E 228
 HSS Co8, 2 FLUTE, SHORT LENGTH
HSS Co8, ,

HSS
Co8 30 PLAIN p.E230, 231
Well - designed for the plunge cutting, pocketing and
general purpose.
up to 3mm

3mm over

PLAIN SHANK E2420 Series Unit : mm

EDP No. EDP No. d EDP No. EDP No. d

D I L D I L
PLAIN TiAIN h6 PLAIN TiAIN h6

E2420010 EQ420010 1 6 2.5 45 E2420200 EQ420200 20 20 38 110

E2420015 EQ420015 1.5 6 4 45 E2420210 EQ420210 21 20 45 110
E2420020 EQ420020 2 6 5 50 E2420220 EQ420220 22 20 45 110
E2420025 EQ420025 2.5 6 6 50 E2420230 EQ420230 23 25 50 120
E2420030 EQ420030 3 6 8 50 E2420240 EQ420240 24 25 50 120
E2420035 EQ420035 3.5 8 8 60 E2420250 EQ420250 25 25 50 120
E2420040 EQ420040 4 8 8 60 E2420260 EQ420260 26 25 50 120
E2420045 EQ420045 4.5 8 10 60 E2420270 EQ420270 27 25 55 125
E2420050 EQ420050 5 8 10 60 E2420280 EQ420280 28 25 55 12512
E2420055 EQ420055 5.5 8 12 60 E2420290 EQ420290 29 25 55 5
E2420060 EQ420060 6 8 12 60 E2420300 EQ420300 30 25 55 125
E2420070 EQ420070 7 10 14 60 E2420310 EQ420310 31 32 60 145
E2420080 EQ420080 8 10 14 60 E2420320 EQ420320 32 32 60 145
E2420090 EQ420090 9 10 18 70 E2420330 EQ420330 33 32 60 145
E2420100 EQ420100 10 10 18 70 E2420340 EQ420340 34 32 60 145
E2420110 EQ420110 11 12 22 80 E2420350 EQ420350 35 32 60 145
E2420120 EQ420120 12 12 22 80 E2420360 EQ420360 36 32 65 150
E2420130 EQ420130 13 12 26 85 E2420370 EQ420370 37 32 65 150
E2420140 EQ420140 14 16 26 90 E2420380 EQ420380 38 32 65 150
E2420150 EQ420150 15 16 30 95 E2420390 EQ420390 39 32 65 150
E2420160 EQ420160 16 16 30 95 E2420400 EQ420400 40 32 65 150
E2420170 EQ420170 17 16 34 95 E2420420 EQ420420 42 42 70 160
E2420180 EQ420180 18 16 34 95 E2420450 EQ420450 45 42 70 160
E2420190 EQ420190 19 20 38 110 E2420500 EQ420500 50 42 70 165

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA.
TOLERANCE D : MILL DIAMETER
d : SHANK DIAMETER
h6 l : LENGTH OF CUT
L : OVERALL LENGTH

E 229
 2FLUTE, FINISH SLOTTING, HSS Co8 END MILLS

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS

HARDNESS ~HRc20 ~HRc20 ~HRc30 ~HRc30 ~HRc40

STRENGTH ~ 500N/ mm2 ~ 500N/ mm2 ~ 500N/ mm2 1000 ~ 500N/ mm2
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
2 5600 40 4500 30 4000 30 2200 15 12000 160
3 3500 55 3200 45 2500 40 1600 20 11000 250
4 2800 70 2200 55 1800 45 1100 30 8000 290
5 2200 90 1800 70 1600 60 900 35 6300 310
6 1800 90 1600 80 1200 60 800 40 5600 310
8 1400 100 1100 90 900 70 560 45 4000 390
10 1100 100 900 90 800 80 450 45 3100 400
12 900 110 800 100 630 80 400 50 2500 380
14 800 110 700 90 560 80 350 50 2200 350
16 700 110 560 90 450 70 280 45 2000 350
18 630 100 500 90 400 70 250 45 1800 350
20 560 100 450 90 400 70 220 45 1600 320
22 500 100 450 90 350 70 220 45 1400 300
25 450 90 400 80 310 60 180 35 1200 280
28 400 80 350 70 280 55 160 30 1100 270
30 350 70 310 60 250 50 160 30 1100 270
32 350 70 280 55 220 45 140 30 1000 240
36 310 60 250 50 200 40 120 25 900 220
40 280 60 220 50 180 40 110 25 800 200

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN.
FEED=mm / min.

E 230
 2FLUTE, FINISH SLOTTING, HSS Co8 END MILLS, TiCN-COATED

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS

HARDNESS ~HRc20 ~HRc20 ~HRc30 ~HRc30 ~HRc40

STRENGTH ~ 500N/ mm2 500~800N/ mm2 800~ 1000N/ mm2 1000 ~ 1300N/ mm2
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
2 7300 50 6000 40 5000 40 2900 20 16000 210
3 4500 70 4200 60 3300 50 2100 25 14000 330
4 3600 90 2900 70 2300 60 1400 40 10000 380
5 2900 115 2300 90 2100 80 1200 45 8200 400
6 2300 115 2000 105 1600 80 1000 50 7300 400
8 1800 130 1400 115 1200 90 730 60 5000 510
10 1400 130 1200 115 1000 105 600 60 4000 520
12 1200 145 1000 130 800 105 500 65 3300 500
14 1000 145 900 115 700 105 450 65 2800 450
16 900 145 700 115 600 90 360 60 2600 450
18 800 130 650 115 500 90 320 60 2300 450
20 730 130 600 115 500 90 300 60 2100 420
22 650 130 600 115 450 90 280 60 1800 390
25 600 120 500 115 400 80 230 48 1600 360
28 500 105 450 90 350 70 210 40 1400 350
30 450 90 400 80 320 65 210 40 1400 350
32 450 90 360 70 280 60 180 40 1300 310
36 400 80 320 65 260 50 160 30 1200 280
40 360 80 280 65 230 50 140 30 1000 260

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN.
FEED=mm / min.

E 231
 HSS Co8, 4FLUTE CENTER CUTTING REGULAR LENGTH
HSS Co8,

HSS
Co8 30 PLAIN p.E237, 238

PLAIN SHANK E2412 Series Unit : mm

EDP No. d
EDP No. D I L
TiAIN h6

E2412010 EQ412010 1 6 2.5 55

E2412015 EQ412015 1.5 6 4 55
E2412020 EQ412020 2 6 6 55
E2412025 EQ412025 2.5 6 7 55
E2412030 EQ412030 3 6 10 55
E2412035 EQ412035 3.5 8 12 60
E2412040 EQ412040 4 8 12 60
E2412045 EQ412045 4.5 8 15 65
E2412050 EQ412050 5 8 15 65
E2412055 EQ412055 5.5 8 15 65
E2412060 EQ412060 6 8 15 65
E2412065 EQ412065 6.5 10 20 75
E2412070 EQ412070 7 10 20 75
E2412075 EQ412075 7.5 10 20 75
E2412080 EQ412080 8 10 21 75
E2412085 EQ412085 8.5 10 25 80
E2412090 EQ412090 9 10 25 80
E2412095 EQ412095 9.5 10 25 80
E2412100 EQ412100 10 10 26 80
E2412105 EQ412105 10.5 12 30 90
E2412110 EQ412110 11 12 30 90
E2412115 EQ412115 11.5 12 30 90
E2412120 EQ412120 12 12 31 90
E2412130 EQ412130 13 12 35 95
E2412912 EQ412912 14 12 35 95
E2412140 EQ412140 14 16 35 100
E2412150 EQ412150 15 16 40 105
E2412160 EQ412160 16 16 40 105
E2412170 EQ412170 17 16 40 105

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA.
TOLERANCE D : MILL DIAMETER
d : SHANK DIAMETER
h6 l : LENGTH OF CUT
L : OVERALL LENGTH

E 232
 HSS Co8, 4FLUTE, CENTER CUTTING REGULAR LENGTH
HSS Co8,

HSS
Co8 30 PLAIN p.E237, 238

PLAIN SHANK E2412 Series Unit : mm

EDP No. EDP No. d

D I L
PLAIN TiAIN h6

E2412180 EQ412180 18 16 40 105

E2412190 EQ412190 19 20 45 115
E2412200 EQ412200 20 20 45 115
E2412210 EQ412210 21 20 45 115
E2412220 EQ412220 22 20 45 115
E2412230 EQ412230 23 25 50 125
E2412240 EQ412240 24 25 50 125
E2412250 EQ412250 25 25 50 125
E2412260 EQ412260 26 25 50 125
E2412270 EQ412270 27 25 55 125
E2412280 EQ412280 28 25 55 125
E2412290 EQ412290 29 25 55 125
E2412300 EQ412300 30 25 55 125
E2412310 EQ412310 31 32 60 145
E2412320 EQ412320 32 32 60 145
E2412330 EQ412330 33 32 60 145
E2412340 EQ412340 34 32 60 145
E2412350 EQ412350 35 32 60 145
E2412360 EQ412360 36 32 65 150
E2412370 EQ412370 37 32 65 150
E2412380 EQ412380 38 32 65 150
E2412390 EQ412390 39 32 65 150
E2412400 EQ412400 40 32 65 150
E2412410 EQ412410 41 42 70 160
E2412420 EQ412420 42 42 70 160
E2412430 EQ412430 43 42 70 160
E2412440 EQ412440 44 42 70 160
E2412450 EQ412450 45 42 70 160
E2412460 EQ412460 46 42 75 160
E2412470 EQ412470 47 42 75 160
E2412480 EQ412480 48 42 75 165
E2412490 EQ412490 49 42 75 165
E2412500 EQ412500 50 42 75 165

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA.
TOLERANCE D : MILL DIAMETER
d : SHANK DIAMETER
h6 l : LENGTH OF CUT
L : OVERALL LENGTH

E 233
 HSS Co8, 4FLUTE, CENTER CUTTING LONG LENGTH
HSS Co8,

HSS
Co8 30 PLAIN p.E237, 238
Possible for deeper & wider cutting by using the much
longer flutes.

PLAIN SHANK E2659 Series Unit : mm

EDP No. EDP No. d

D I L
PLAIN TiAIN h6

E2659030 EQ659030 3 6 15 60
E2659040 EQ659040 4 8 20 70
E2659050 EQ659050 5 8 25 75
E2659060 EQ659060 6 8 25 75
E2659070 EQ659070 7 10 35 90
E2659080 EQ659080 8 10 35 90
E2659090 EQ659090 9 10 45 100
E2659100 EQ659100 10 10 45 100
E2659110 EQ659110 11 12 55 115
E2659120 EQ659120 12 12 55 115
E2659130 EQ659130 13 12 55 115
E2659140 EQ659140 14 16 55 120
E2659150 EQ659150 15 16 65 130
E2659160 EQ659160 16 16 65 130
E2659170 EQ659170 17 16 65 130
E2659180 EQ659180 18 16 65 130
E2659190 EQ659190 19 20 75 145
E2659200 EQ659200 20 20 75 145
E2659210 EQ659210 21 20 75 145
E2659220 EQ659220 22 20 75 145
E2659230 EQ659230 23 25 90 165
E2659240 EQ659240 24 25 90 165
E2659250 EQ659250 25 25 90 165
E2659260 EQ659260 26 25 90 165
E2659270 EQ659270 27 25 90 165
E2659280 EQ659280 28 25 90 165
E2659290 EQ659290 29 25 90 165
E2659300 EQ659300 30 25 90 165
E2659310 EQ659310 31 32 95 180
E2659320 EQ659320 32 32 95 180
E2659330 EQ659330 33 32 100 185
E2659340 EQ659340 34 32 100 185
E2659350 EQ659350 35 32 100 185
E2659360 EQ659360 36 32 105 190
E2659370 EQ659370 37 32 105 190
E2659380 EQ659380 38 32 105 190
E2659390 EQ659390 39 32 110 195
E2659400 EQ659400 40 32 110 195
E2659420 EQ659420 42 42 115 200
E2659450 EQ659450 45 42 120 205
E2659460 EQ659460 46 42 125 215
E2659480 EQ659480 48 42 125 215
E2659500 EQ659500 50 42 125 215

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA.
TOLERANCE D : MILL DIAMETER
d : SHANK DIAMETER
h6 l : LENGTH OF CUT
L : OVERALL LENGTH

E 234
 HSS Co8, 4 FLUTE, EXTRA LONG LENGTH
HSS Co8,

HSS
Co8 30 PLAIN p.E237, 238
Much longer flute length than E2407
type allows deeper & wider cutting.

PLAIN SHANK E2750 Series Unit : mm

EDP No. EDP No. d EDP No. EDP No. d

D I L D I L
PLAIN TiAIN h6 PLAIN TiAIN h6

E2750160 EQ750160 16 16 100 160 E2750300 EQ750300 30 25 120 200

E2750180 EQ750180 18 16 100 180 E2750906 EQ750906 30 25 150 250
E2750200 EQ750200 20 20 100 180 E2750907 EQ750907 30 25 200 280
E2750901 EQ750901 20 20 120 200 E2750320 EQ750320 32 32 150 230
E2750902 EQ750902 20 20 150 230 E2750908 EQ750908 32 32 200 280
E2750220 EQ750220 22 20 120 200 E2750350 EQ750350 35 32 150 250
E2750240 EQ750240 24 25 100 180 E2750909 EQ750909 35 32 200 300
E2750903 EQ750903 24 25 150 250 E2750360 EQ750360 36 32 150 250
E2750250 EQ750250 25 25 100 180 E2750380 EQ750380 38 32 150 250
E2750904 EQ750904 25 25 120 220 E2750400 EQ750400 40 32 150 250
E2750905 EQ750905 25 25 150 250 E2750910 EQ750910 40 32 200 300
E2750260 EQ750260 26 25 150 250 E2750450 EQ750450 45 42 200 300
E2750280 EQ750280 28 25 150 250 E2750500 EQ750500 50 42 200 300

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA.
TOLERANCE D : MILL DIAMETER
d : SHANK DIAMETER
h6 l : LENGTH OF CUT
L : OVERALL LENGTH

E 235
 HSS Co8, 4&6 FLUTE, SHORT LENGTH
HSS Co8, 4 & 6 ,

HSS
Co8 30 PLAIN p.E237, 238
Recommended for pocketing copy milling, cam profiling,
die sinking and slotting.

PLAIN SHANK E2421 Series Unit : mm

EDP No. EDP No. d EDP No. EDP No. d

D I L Z D I L Z
PLAIN TiAIN h6 PLAIN TiAIN h6

E2421025 EQ421025 2.5 6 10 50 4 E2421220 EQ421220 22 20 45 110 4

E2421030 EQ421030 3 6 10 50 4 E2421230 EQ421230 23 25 50 120 4
E2421035 EQ421035 3.5 8 12 60 4 E2421240 EQ421240 24 25 50 120 4
E2421040 EQ421040 4 8 12 60 4 E2421250 EQ421250 25 25 50 120 4
E2421045 EQ421050 4.5 8 15 60 4 E2421260 EQ421260 26 25 50 120 4
E2421050 EQ421055 5 8 15 60 4 E2421270 EQ421270 27 25 55 125 4
E2421055 EQ421060 5.5 8 15 60 4 E2421280 EQ421280 28 25 55 125 4
E2421060 EQ421060 6 8 15 60 4 E2421290 EQ421290 29 25 55 125 4
E2421070 EQ421070 7 10 20 60 4 E2421300 EQ421300 30 25 55 125 4
E2421080 EQ421080 8 10 20 60 4 E2421310 EQ421310 31 32 60 145 4
E2421090 EQ421090 9 10 25 70 4 E2421320 EQ421320 32 32 60 145 4
E2421100 EQ421100 10 10 25 70 4 E2421330 EQ421330 33 32 60 145 4
E2421110 EQ421110 11 12 30 80 4 E2421340 EQ421340 34 32 60 145 4
E2421120 EQ421120 12 12 30 80 4 E2421350 EQ421350 35 32 60 145 4
E2421130 EQ421130 13 12 35 85 4 E2421360 EQ421360 36 32 65 150 4
E2421140 EQ421140 14 16 35 90 4 E2421370 EQ421370 37 32 65 150 4
E2421150 EQ421150 15 16 40 95 4 E2421380 EQ421380 38 32 65 150 4
E2421160 EQ421160 16 16 40 95 4 E2421390 EQ421390 39 32 65 150 4
E2421170 EQ421170 17 16 40 95 4 E2421400 EQ421400 40 32 65 150 4
E2421180 EQ421180 18 16 40 95 4 E2421420 EQ421420 42 42 70 160 6
E2421190 EQ421190 19 20 45 110 4 E2421450 EQ421450 45 42 70 160 6
E2421200 EQ421200 20 20 45 110 4 E2421500 EQ421500 50 42 75 165 6
E2421210 EQ421210 21 20 45 110 4

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA. D : MILL DIAMETER

TOLERANCE d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 236
 MULTI FLUTE, FINISH SIDE CUTTING, HSS Co8, END MILLS

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS

HARDNESS ~HRc20 ~HRc20 ~HRc30 ~HRc30 ~HRc40

STRENGTH ~ 500N/ mm 2
~ 500N/ mm 2 2
~ 500N/ mm 1000 ~ 500N/ mm2
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
2 5600 80 4500 55 4000 45 2200 20 12000 240
3 3500 110 3200 80 2500 60 1600 30 11000 380
4 2800 140 2200 100 1800 65 1100 45 8000 440
5 2200 180 1800 125 1600 90 900 50 6300 470
6 1800 180 1600 145 1200 90 800 60 5600 470
8 1400 200 1100 160 900 105 560 65 4000 580
10 1100 200 900 160 800 120 450 65 3100 600
12 900 220 800 180 630 120 400 75 2500 570
14 800 220 700 160 560 120 350 75 2200 530
16 700 220 560 160 450 105 280 65 2000 530
18 630 200 500 160 400 105 250 65 1800 530
20 560 200 450 160 400 105 220 65 1600 480
22 500 200 450 160 350 105 220 65 1400 450
25 450 180 400 145 310 90 180 50 1200 420
28 400 160 350 125 280 80 160 45 1100 400
30 350 140 310 110 250 75 160 45 1100 400
32 350 140 280 100 220 65 140 45 1000 360
36 310 120 250 90 200 60 120 35 900 330
40 280 120 220 90 180 60 110 35 800 300

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN.
FEED=mm / min.

E 237
 MULTI FLUTE, FINISH SIDE CUTTING, HSS Co8 END MILLS, TiCN-COATED

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS

MATERIAL ALUMINUM
ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS

HARDNESS ~HRc20 ~HRc20 ~HRc30 ~HRc30 ~HRc40

STRENGTH ~ 500N/ mm2 ~ 500N/ mm2 ~ 500N/ mm2 1000 ~ 500N/ mm2
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
2 7300 105 6000 70 5000 60 2900 25 16000 310
3 4500 145 4200 105 3300 80 2100 40 14000 500
4 3600 180 2900 130 2300 85 1400 60 10000 570
5 2900 235 2300 160 2100 115 1200 65 8200 610
6 2300 235 2000 190 1600 115 1000 80 7300 610
8 1800 260 1400 210 1200 135 730 85 5000 750
10 1400 260 1200 210 1000 155 600 85 4000 780
12 1200 285 1000 235 800 155 500 95 3300 740
14 1000 285 900 210 700 155 450 95 2800 690
16 900 285 700 210 600 135 360 85 2600 690
18 800 260 650 210 500 135 320 85 2300 690
20 730 260 600 210 500 135 300 85 2100 620
22 650 260 600 210 450 135 280 85 1800 580
25 600 235 500 190 400 115 230 65 1600 550
28 500 210 450 160 350 105 210 60 1400 520
30 450 180 400 145 320 95 210 60 1400 520
32 450 180 360 130 280 85 180 60 1300 470
36 400 155 320 120 260 80 160 45 1200 430
40 360 155 280 120 230 80 140 45 1000 390

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN.
FEED=mm / min.

E 238
 HSS Co8, 2 FLUTE, REGULAR LENGTH BALL NOSE
HSS Co8, 2 , ,

HSS
Co8 30 PLAIN
p.E241, 242
The two flute ball End Mills are designed for milling of
radius bottom slot, fillet and special contour. The end
teeth are cut to center allowing these end mills to drill
into material at the beginning of a slotting cut. The two
flute design provides good chip ejection ability in
slotting.

PLAIN SHANK E2480 Series Unit : mm

EDP No. EDP No. d EDP No. EDP No. d

D I L D I L
PLAIN TiAIN h6 PLAIN TiAIN h6

E2480010 EQ480010 1 6 2.5 50 E2480170 EQ480170 17 16 34 140

E2480015 EQ480015 1.5 6 4 50 E2480180 EQ480180 18 16 34 140
E2480020 EQ480020 2 6 5 50 E2480190 EQ480190 19 16 38 140
E2480025 EQ480025 2.5 6 6 60 E2480200 EQ480200 20 20 38 160
E2480030 EQ480030 3 6 8 60 E2480210 EQ480210 21 20 45 170
E2480901 EQ480901 4 6 8 70 E2480220 EQ480220 22 20 45 170
E2480902 EQ480902 5 6 10 80 E2480230 EQ480230 23 20 50 180
E2480903 EQ480903 6 6 12 90 E2480908 EQ480908 24 20 50 180
E2480904 EQ480904 7 8 14 90 E2480240 EQ480240 24 25 50 180
E2480905 EQ480905 8 8 14 100 E2480250 EQ480250 25 25 50 180
E2480090 EQ480090 9 10 18 100 E2480260 EQ480260 26 25 50 180
E2480100 EQ480100 10 10 18 100 E2480270 EQ480270 27 25 50 180
E2480110 EQ480110 11 12 22 100 E2480280 EQ480280 28 25 50 180
E2480120 EQ480120 12 12 22 110 E2480300 EQ480300 30 25 55 180
E2480130 EQ480130 13 12 26 110 E2480320 EQ480320 32 32 60 180
E2480906 EQ480906 14 12 26 110 E2480350 EQ480350 35 32 60 180
E2480907 EQ480907 15 12 30 110 E2480400 EQ480400 40 32 65 200
E2480160 EQ480160 16 16 30 140 E2480500 EQ480500 50 42 75 210

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA.
TOLERANCE D : MILL DIAMETER
d : SHANK DIAMETER
h6 l : LENGTH OF CUT
L : OVERALL LENGTH

E 239
 HSS Co8, 4&6 FLUTE, SHORT LENGTH BALL
HSS Co8, 4 & 6 , ,

HSS DIN
Co8 1889 DIN
30 1835B p.E241, 242
The four flute ball end mills are designed for milling of radius
bottom slot, fillet and special contour. The end teeth are cut
to center allowing these end mills to drill into material at the
beginning of a slotting cut.

FLAT SHANK E2410 Series Unit : mm

SHANK
EDP No. EDP No. MILL LENGTH OVERALL No.OF
DIAMETER
FLAT TiAlN DIAMETER OF CUT LENGTH FLUTE
h6
E2410060 EQ410060 6 6 13 57 4
E2410080 EQ410080 8 10 19 69 4
E2410100 EQ410100 10 10 22 72 4
E2410120 EQ410120 12 12 26 83 4
E2410160 EQ410160 16 16 32 92 4
E2410200 EQ410200 20 20 38 104 4
E2410250 EQ410250 25 25 45 121 6

HSS Co8, 4&6 FLUTE LONG LENGTH BALL NOSE

HSS Co8, 4 & 6 , ,

HSS DIN
Co8 1889 DIN
30 1835B

Much longer flute length than E2410 type allows deeper &
wider cutting.

FLAT SHANK E2429 Series Unit : mm

SHANK
EDP No. EDP No. MILL LENGTH OVERALL No.OF
DIAMETER
FLAT TiAlN DIAMETER OF CUT LENGTH FLUTE
h6
E2429100 EQ429100 10 10 45 95 4
E2429120 EQ429120 12 12 53 110 4
E2429160 EQ429160 16 16 63 123 4
E2429200 EQ429200 20 20 75 141 4
E2429250 EQ429250 25 25 90 166 6

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA.
TOLERANCE

h6

E 240
 2FLUTE, BALL NOSE, HSS Co8 END MILLS

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS

HARDNESS ~HRc20 ~HRc20 ~HRc30 ~HRc30 ~HRc40

STRENGTH ~ 500N/ mm2 500~800N/ mm2 800~1000N/ mm2 1000 ~ 1300N/ mm2
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
R 1.5 3.0 4500 95 3400 70 2000 30 1400 20 11000 230
R 1.5 4.0 3200 115 2400 80 1400 35 1000 25 8000 260
R 1.5 6.0 2200 135 1700 90 1000 45 700 25 5600 280
R 1.5 8.0 1600 160 1200 105 700 50 500 30 4000 350
R 1.5 10.0 1300 180 1000 120 560 60 400 35 3200 360
R 1.5 12.0 1000 170 800 105 450 55 320 35 2500 340
R 1.5 16.0 800 150 600 100 350 55 250 35 2000 300
R 1.5 20.0 600 140 500 85 300 50 200 35 1600 280
R 1.5 25.0 500 130 400 70 220 40 160 30 1300 250

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN.
FEED=mm / min.

MULTI FLUTE, BALL NOSE, HSS Co8 END MILLS

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS

HARDNESS ~HRc20 ~HRc20 ~HRc30 ~HRc30 ~HRc40

2 2 2
STRENGTH ~ 500N/ mm 500~800N/ mm 800~1000N/ mm 1000 ~ 1300N/ mm2
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
R 3.0 6.0 2200 200 1700 135 1000 70 700 40 5600 420
R 4.0 8.0 1600 240 1200 160 700 75 500 45 4000 530
R 5.0 10.0 1300 270 1000 180 560 90 400 50 3200 540
R 6.0 12.0 1000 260 800 160 450 80 320 50 2500 510
R 8.0 16.0 800 230 600 150 350 80 250 50 2000 450
R 10.0 20.0 600 210 500 130 300 75 200 50 1600 420
R 12.5 25.0 500 200 400 105 200 60 160 45 1300 380

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN.
FEED=mm / min.

E 241
 2FLUTE, BALL NOSE, HSS Co8 END MILLS, TiCN-COATED

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS

HARDNESS ~HRc20 ~HRc20 ~HRc30 ~HRc30 ~HRc40

2 2 2
STRENGTH ~ 500N/ mm 500~800N/ mm 800~1000N/ mm 1000 ~ 1300N/ mm2
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
R 1.5 3.0 6000 125 4400 90 2600 40 1800 25 14000 300
R 1.5 4.0 4000 150 3100 105 1800 45 1300 30 10000 340
R 1.5 6.0 3000 175 2200 115 1300 60 900 30 7300 360
R 1.5 8.0 2000 210 1600 135 900 65 650 40 5000 450
R 1.5 10.0 1700 235 1300 155 730 80 500 45 4000 470
R 1.5 12.0 1300 220 1000 135 600 70 400 45 3300 440
R 1.5 16.0 1000 200 800 130 450 70 300 45 2600 390
R 1.5 20.0 800 180 650 110 400 65 250 45 2000 360
R 1.5 25.0 650 170 500 90 300 50 200 40 1700 330

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN.
FEED=mm / min.

MULTI FLUTE, BALL NOSE, HSS Co8 END MILLS, TiCN-COATED

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS

HARDNESS ~HRc20 ~HRc20 ~HRc30 ~HRc30 ~HRc40

STRENGTH ~ 500N/ mm2 500~800N/ mm2 800~1000N/ mm2 1000 ~ 1300N/ mm2
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
R 3.0 6.0 3000 260 2200 175 1300 90 900 50 7300 550
R 4.0 8.0 2000 310 1600 210 900 95 650 60 5000 690
R 5.0 10.0 1700 350 1300 230 730 115 500 65 4000 700
R 6.0 12.0 1300 340 1000 210 600 105 400 65 3300 660
R 8.0 16.0 1000 300 800 200 450 105 300 65 2600 590
R 10.0 20.0 800 270 650 170 400 95 250 65 2000 550
R 12.5 25.0 650 260 500 135 300 80 200 60 1700 490

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN.
FEED=mm / min.

E 242
 HSS Co8, 2 FLUTE FOR ALUMINUM
HSS Co8,

HSS DIN
Co8 844 DIN
42 1835B p.E245
Recommended for cutting aluminum and other non-
ferrous materials.

FLAT SHANK E2464 Series Unit : mm

EDP No. EDP No. D d EDP No. EDP No. D d

I L I L
FLAT HARDLUBE e8 h6 FLAT HARDLUBE e8 h6

E2464020 EU464020 2 6 7 51 E2464110 EU464110 11 12 22 79

E2464025 EU464025 2.5 6 8 52 E2464120 EU464120 12 12 26 83
E2464030 EU464030 3 6 8 52 E2464130 EU464130 13 12 26 83
E2464035 EU464035 3.5 6 10 54 E2464140 EU464140 14 12 26 83
E2464040 EU464040 4 6 11 55 E2464150 EU464150 15 12 26 83
E2464045 EU464045 4.5 6 11 55 E2464160 EU464160 16 16 32 92
E2464050 EU464050 5 6 13 57 E2464170 EU464170 17 16 32 92
E2464055 EU464055 5.5 6 13 57 E2464180 EU464180 18 16 32 92
E2464060 EU464060 6 6 13 57 E2464190 EU464190 19 16 32 92
E2464065 EU464065 6 10 16 66 E2464200 EU464200 20 20 38 104
E2464070 EU464070 7 10 16 66 E2464210 EU464210 21 20 38 104
E2464075 EU464075 7.5 10 16 66 E2464220 EU464220 22 20 38 104
E2464080 EU464080 8 10 19 69 E2464230 EU464230 23 20 38 104
E2464085 EU464085 8.5 10 19 69 E2464240 EU464240 24 25 45 121
E2464090 EU464090 9 10 19 69 E2464250 EU464250 25 25 45 121
E2464100 EU464100 10 10 22 72

Tolerances according to DIN 7160 & 7161

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30

e8 D : MILL DIAMETER
d : SHANK DIAMETER
h6 l : LENGTH OF CUT
: 1/1000mm L : OVERALL LENGTH

E 243
 HSS Co8, MULTI FLUTES, 50° HELIX
HSS Co8,

HSS
Co8 2~4 DIN
50 1835B p.E246
Provided with high helix angle(50 ).

Smooth cutting and small cutting resistance.

Suitable for difficult-to-machine materials.

Removal of sharp cutting edges against chipping.

FLAT SHANK E2461, E2462, 2463 Series Unit : mm

MILL SHANK
EDP No. EDP No. LENGTH OVERALL No.OF
DIAMETER DIAMETER
PLAIN TiAIN OF CUT LENGTH FLUTE
k10 h6
E2461020 EQ461020 2 6 7 51 2
E2461030 EQ461030 3 6 8 52 2
E2461040 EQ461040 4 6 11 55 2
E2461050 EQ461050 5 6 13 57 2
E2462060 EQ462060 6 6 13 57 3
E2462070 EQ462070 7 10 16 66 3
E2462080 EQ462080 8 10 19 69 3
E2462090 EQ462090 9 10 19 69 3
E2462100 EQ462100 10 10 22 72 3
E2462120 EQ462120 12 12 26 83 3
E2462140 EQ462140 14 12 26 83 3
E2462150 EQ462150 15 12 26 83 3
E2462160 EQ462160 16 16 32 92 3
E2462180 EQ462180 18 16 32 92 3
E2462200 EQ462200 20 20 38 104 3
E2463250 EQ463250 25 25 45 121 4
E2463300 EQ463300 30 25 45 121 4

Tolerances according to DIN 7160 & 7161

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30

k10 D : MILL DIAMETER

d : SHANK DIAMETER
h6 l : LENGTH OF CUT
: 1/1000mm L : OVERALL LENGTH

E 244
 2FLUTE, FINISH, 42° HELIX HSS Co8 FOR ALUMINUM

Slotting Side Cutting

ALUMINUM ALUMINUM
MATERIAL MATERIAL
NON-FERROUS METALS NON-FERROUS METALS

DIAMETER RPM FEED DIAMETER RPM FEED

3 8000 560 3 8000 730
6 7000 700 6 7000 900
8 6000 850 8 6000 1100
10 5000 1200 10 5000 1500
12 5000 1200 12 5000 1500
14 3500 1240 14 3500 1600
16 3500 1240 16 3500 1600
18 2300 1300 18 2300 1700
20 2300 1300 20 2300 1700

A: 3 ~ 10=0.25 D
~ 20=0.5 D

RPM=REVOLUTION PER MIN.

Feed=mm / min

E 245
 MULTI FLUTE, FINISH SIDE CUTTING, 50° HELIX HSS Co8 END MILLS

CARBON STEELS CARBON STEELS CARBON STEELS

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS
TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30
STRENGTH ~ 500N/ 500~800N/ 800~1000N/
DIAMETER RPM FEED RPM FEED RPM FEED
2 5000 35 4500 25 2500 10
3 3500 50 2800 35 1800 20
4 2500 60 2000 40 1200 25
5 2000 75 1800 55 1000 30
6 1800 85 1300 55 900 35
8 1200 95 1000 65 600 40
10 1000 95 900 70 500 40
12 900 110 700 70 450 45
14 800 95 600 70 400 45
16 600 95 500 65 300 40
18 550 95 450 65 280 40
20 500 95 450 65 250 40
22 500 95 400 65 250 40
25 450 85 350 55 200 30
28 400 75 300 50 180 25
30 350 65 280 45 180 25

RPM=REVOLUTION PER MIN.

Feed=mm / min

E 246
 HSS Co8, 2 FLUTE TAPER
HSS Co8, ,

HSS
Co8 30 PLAIN

for diecast dies & molds.

PLAIN SHANK E2682 Series Unit : mm

SHANK
EDP No. MILL LENGTH OVERALL TAPER
DIAMETER
PLAIN DIAMETER OF CUT LENGTH ANGLE
h6
E2682010 1 6 4 45 30·
E2682011 1 6 4 45 1
E2682012 1 6 4 45 1 30·
E2682013 1 6 4 45 2
E2682014 1 6 4 45 3
E2682015 1.5 6 5 45 30·
E2682016 1.5 6 5 45 1
E2682017 1.5 6 5 45 1 30·
E2682018 1.5 6 5 45 2
E2682019 1.5 6 5 45 3
E2682020 2 6 6 45 30·
E2682021 2 6 6 45 1
E2682022 2 6 6 45 1 30·
E2682023 2 6 6 45 2
E2682024 2 6 6 45 3
E2682025 2 6 6 45 5
E2682902 2 6 6 45 2 30·
E2682026 2.5 6 8 45 30·
E2682027 2.5 6 8 45 1
E2682028 2.5 6 8 45 1 30·
E2682029 2.5 6 8 45 2
E2682903 2.5 6 8 45 2 30·
E2682904 2.5 6 8 45 3
E2682901 2.5 6 8 50 5
E2682030 3 6 10 45 30·
E2682031 3 6 10 45 1

Unit : mm

TOLERANCE
of MILL DIA.

TOLERANCE
of TAPER ANGLE

E 247
 HSS Co8, 2 FLUTE TAPER
HSS Co8, ,

HSS
Co8 30 PLAIN

for diecast dies & molds.

PLAIN SHANK E2682 Series Unit : mm

SHANK
EDP No. MILL LENGTH OVERALL TAPER
DIAMETER
PLAIN DIAMETER OF CUT LENGTH ANGLE
h6
E2682032 3 6 10 45 1 30·
E2682033 3 6 10 45 2
E2682036 3 6 10 45 2 30·
E2682034 3 6 10 45 3
E2682035 3 6 10 50 5
E2682040 4 6 15 50 30·
E2682041 4 6 15 50 1
E2682042 4 6 15 50 1 30·
E2682043 4 6 15 50 2
E2682046 4 6 15 50 2 30·
E2682044 4 6 15 50 3
E2682045 4 6 15 60 5
E2682050 5 6 20 55 30·
E2682051 5 6 20 55 1
E2682052 5 6 20 55 1 30·
E2682053 5 6 20 55 2
E2682054 5 6 20 55 2 30·
E2682055 5 6 20 55 3
E2682056 5 8 20 80 5
E2682060 6 6 20 55 30·
E2682061 6 6 20 55 1
E2682062 6 6 20 55 1 30·
E2682063 6 6 20 55 2
E2682064 6 6 20 55 2 30·
E2682065 6 8 20 60 3
E2682066 6 8 20 80 5

Unit : mm

TOLERANCE
of MILL DIA.

TOLERANCE
of TAPER ANGLE

E 248
 HSS Co8, 4 FLUTE TAPER
HSS Co8, ,

HSS
Co8 30 PLAIN

for diecast dies & molds.

PLAIN SHANK E2683 Series Unit : mm

EDP No. MILL SHANK LENGTH OVERALL TAPER

PLAIN DIAMETER DIAMETER OF CUT LENGTH ANGLE

E2683080 8 8 25 65 30·
E2683081 8 8 25 65 1
E2683082 8 8 25 65 1 30·
E2683083 8 8 25 65 2
E2683084 8 10 25 70 2 30·
E2683085 8 10 25 70 3
E2683086 8 12 25 90 5
E2683100 10 10 35 85 30·
E2683101 10 10 35 85 1
E2683102 10 10 35 85 1 30·
E2683103 10 12 35 90 2
E2683104 10 12 35 90 2 30·
E2683105 10 12 35 90 3
E2683106 10 16 35 115 5
E2683120 12 12 55 110 30·
E2683121 12 12 55 110 1
E2683122 12 12 55 110 1 30·
E2683123 12 12 55 110 2
E2683124 12 16 55 110 2 30·
E2683125 12 16 55 110 3
E2683126 12 20 55 110 5
E2683127 12 20 55 155 5

Unit : mm

TOLERANCE
of MILL DIA.

TOLERANCE
of TAPER ANGLE

HSS Co8, TAPER - SIDE CUTTING

HSS Co8,
CARBON STEEL CARBON STEEL CARBON STEEL
MATERIAL ALLOY STEEL ALLOY STEEL ALLOY STEEL
TOOL STEEL TOOL STEEL TOOL STEEL
HARDNESS ~HRc20 HRc20~~HRc30 HRc30~~HRc40
DIAMETER RPM FEED RPM FEED RPM FEED
2 3800 50 3500 38 2800 22
3 2800 50 2400 38 1900 22
4 2000 50 1750 38 1400 22
5 1700 55 1400 42 1100 27
6 1300 55 1150 46 940 27
8 1000 55 880 46 700 27
10 780 55 700 46 560 27
12 600 55 580 46 530 27

For 4flutes, the feed rate should be doubled. RPM=REVOLUTION PER MIN.
Feed=mm / min

E 249
 HSS Co8, COARSE PITCH, CENTER CUTTING, SHORT ROUGHING
HSS Co8,

HSS
Co8 4~6 DIN
30 1835B COARSE p.E258~261
This general purpose rougher is designed for high production
metal removal in a wide range of work piece material. It is
recommanded for cutting steel grades and many non-ferrous
material.

FLAT SHANK E2760 Series Unit : mm

EDP No. EDP No. d EDP No. EDP No. d

D I L Z D I L Z
FLAT TiAIN h6 FLAT TiAIN h6

E2760060 EQ760060 6 8 15 60 4 E2760280 EQ760280 28 25 55 125 6

E2760070 EQ760070 7 10 20 65 4 E2760290 EQ760290 29 25 55 125 6
E2760080 EQ760080 8 10 20 65 4 E2760300 EQ760300 30 25 55 125 6
E2760090 EQ760090 9 12 25 75 4 E2760310 EQ760310 31 32 60 145 6
E2760100 EQ760100 10 12 25 75 4 E2760320 EQ760320 32 32 60 145 6
E2760110 EQ760110 11 12 30 80 4 E2760330 EQ760330 33 32 60 145 6
E2760120 EQ760120 12 12 30 80 4 E2760340 EQ760340 34 32 60 145 6
E2760130 EQ760130 13 16 35 90 4 E2760350 EQ760350 35 32 60 145 6
E2760140 EQ760140 14 16 35 90 4 E2760360 EQ760360 36 32 60 145 6
E2760150 EQ760150 15 16 40 95 4 E2760370 EQ760370 37 32 65 150 6
E2760160 EQ760160 16 16 40 95 4 E2760380 EQ760380 38 32 65 150 6
E2760170 EQ760170 17 20 40 105 4 E2760390 EQ760390 39 32 65 150 6
E2760180 EQ760180 18 20 40 105 4 E2760400 EQ760400 40 32 65 150 6
E2760190 EQ760190 19 20 45 110 4 E2760420 EQ760420 42 32 65 155 6
E2760200 EQ760200 20 20 45 110 4 E2760942 EQ760942 42 42 65 155 6
E2760210 EQ760210 21 20 45 110 5 E2760450 EQ760450 45 32 70 160 6
E2760220 EQ760220 22 20 45 110 5 E2760945 EQ760945 45 42 70 160 6
E2760230 EQ760230 23 25 50 120 5 E2760480 EQ760480 48 32 70 160 6
E2760240 EQ760240 24 25 50 120 5 E2760948 EQ760948 48 42 70 160 6
E2760250 EQ760250 25 25 50 120 5 E2760500 EQ760500 50 32 70 160 6
E2760260 EQ760260 26 25 50 120 6 E2760950 EQ760950 50 42 70 160 6
E2760270 EQ760270 27 25 55 125 6

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA. D : MILL DIAMETER

TOLERANCE d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 250
 HSS Co8, COARSE PITCH, LONG ROUGHING
HSS Co8,

HSS
Co8 4~6
30 PLAIN COARSE p.E258~261
Much longer flute design than E2758 type allows deeper & wider
cutting.

PLAIN SHANK E2759 Series Unit : mm

EDP No. EDP No. d EDP No. EDP No. d

D I L Z D I L Z
PLAIN TiAIN h6 PLAIN TiAIN h6

E2759100 EQ759100 10 10 45 95 4 E2759280 EQ759280 28 25 90 166 5

E2759120 EQ759120 12 12 53 110 4 E2759300 EQ759300 30 25 90 166 6
E2759140 EQ759140 14 12 53 110 4 E2759320 EQ759320 32 32 106 186 6
E2759160 EQ759160 16 16 63 123 4 E2759350 EQ759350 35 32 106 186 6
E2759180 EQ759180 18 16 63 123 4 E2759360 EQ759360 36 32 106 186 6
E2759200 EQ759200 20 20 75 141 4 E2759400 EQ759400 40 32 125 205 6
E2759220 EQ759220 22 20 75 141 5 E2759450 EQ759450 45 42 125 227 6
E2759250 EQ759250 25 25 90 166 5 E2759500 EQ759500 50 42 150 252 6

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA. D : MILL DIAMETER

TOLERANCE d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 251
 HSS Co8, 3 FLUTE COARSE PITCH, SHORT LENGTH ROUGHING
HSS Co8, ,

HSS
DIN844
Co8 30
DIN
COARSE
1835B p.E258~261
This general purpose rougher is designed for high production metal removal
in a wide range of work piece material. It is recommanded for cutting steel
grades and many non-ferrous material.

FLAT SHANK E2751, 2764 Series Unit : mm

EDP No. EDP No. D d EDP No. EDP No. D d

I L Z I L Z
FLAT TiAIN js12 h6 FLAT TiAIN js12 h6

E2751060 EQ751060 6 6 13 57 3 E2764220 EQ764220 22 20 38 104 3

E2751080 EQ751080 8 10 19 69 3 E2764250 EQ764250 25 25 45 121 3
E2764100 EQ764100 10 10 22 72 3 E2764280 EQ764280 28 25 45 121 3
E2764120 EQ764120 12 12 26 83 3 E2764300 EQ764300 30 25 45 121 3
E2764140 EQ764140 14 12 26 83 3 E2764320 EQ764320 32 32 53 133 3
E2764160 EQ764160 16 16 32 92 3 E2764360 EQ764360 36 32 53 133 3
E2764180 EQ764180 18 16 32 92 3 E2764400 EQ764400 40 32 63 155 3
E2764200 EQ764200 20 20 38 104 3

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50
D : MILL DIAMETER
js12 d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 252
 HSS Co8, 3 FLUTE COARSE PITCH, LONG LENGTH ROUGHING
HSS Co8, ,

HSS
DIN844
Co8 30
DIN
COARSE
1835B p.E258~261
This general purpose rougher is designed for high production metal
removal in a wide range of work piece material. It is recommanded for
cutting steel grades and many non-ferrous material.

Much longer flute design than E2751 & E2764 type allows deeper &
wider cutting.

FLAT SHANK E2752, 2765 Series Unit : mm

EDP No. EDP No. D d EDP No. EDP No. D d

I L Z I L Z
FLAT TiAIN js12 h6 FLAT TiAIN js12 h6

E2752060 EQ752060 6 6 24 68 3 E2765200 EQ765200 20 20 75 141 3

E2752080 EQ752080 8 10 38 88 3 E2765220 EQ765220 22 20 75 141 3
E2765100 EQ765100 10 10 45 95 3 E2765250 EQ765250 25 25 90 166 3
E2765120 EQ765120 12 12 53 110 3 E2765280 EQ765280 28 25 90 166 3
E2765140 EQ765140 14 12 53 110 3 E2765300 EQ765300 30 25 90 166 3
E2765160 EQ765160 16 16 63 123 3 E2765360 EQ765360 36 32 106 186 3
E2765180 EQ765180 18 16 63 123 3 E2765400 EQ765400 40 32 125 217 3

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50
D : MILL DIAMETER
js12 d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 253
 HSS Co8 COARSE PITCH, SHORT LENGTH ROUGHING FOR ALUMINUM
HSS Co8, ,

HSS
DIN844
Co8 37
DIN
1835B AI p.E258~261
This general purpose rougher is designed for high production metal removal
in a wide range of work piece material. It is recommanded for cutting
aliminum and many non-ferrous material.

FLAT SHANK E2755 Series Unit : mm

EDP No. EDP No. D d EDP No. EDP No. D d

I L Z I L Z
FLAT TiAIN js12 h6 FLAT TiAIN js12 h6

E2755060 EQ755060 6 6 13 57 3 E2755180 EQ755180 18 16 32 92 3

E2755080 EQ755080 8 10 19 69 3 E2755200 EQ755200 20 20 38 104 3
E2755100 EQ755100 10 10 22 72 3 E2755220 EQ755220 22 20 38 104 3
E2755120 EQ755120 12 12 26 83 3 E2755250 EQ755250 25 25 45 121 3
E2755140 EQ755140 14 12 26 83 3 E2755300 EQ755300 30 25 45 121 3
E2755160 EQ755160 16 16 32 92 3

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50
D : MILL DIAMETER
js12 d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 254
 HSS Co8, COARSE PITCH, LONG LENGTH ROUGHING FOR ALUMINUM
HSS Co8, ,

HSS
DIN844
Co8 37
DIN
AI
1835B p.E258~261
Much longer flute design than E2755 type allows deeper & wider cutting.

Center cutting

FLAT SHANK E2756 Series

Unit : mm

EDP No. EDP No. D d EDP No. EDP No. D d

I L Z I L Z
FLAT TiAIN js12 h6 FLAT TiAIN js12 h6

E2756100 EQ756100 10 10 45 95 3 E2756200 EQ756200 20 20 75 141 3

E2756120 EQ756120 12 12 53 110 3 E2756220 EQ756220 22 20 75 141 3
E2756140 EQ756140 14 12 53 110 3 E2756250 EQ756250 25 25 90 166 3
E2756160 EQ756160 16 16 63 123 3 E2756300 EQ756300 30 25 90 166 3
E2756180 EQ756180 18 16 63 123 3

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50
D : MILL DIAMETER
js12 d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 255
 HSS Co8, FINE PITCH, SHORT LENGTH ROUGHING
HSS Co8,

HSS
DIN844
Co8 30
DIN
FINE
1835B p.E258~261
This general purpose rougher is designed for high production metal removal
in a wide range of work piece material. It is suitable for a very broad
spectrum of materials having up to high tensile strength. In many case, the
milled surfaces are of acceptable quality.

FLAT SHANK E2753 Series Unit : mm

EDP No. EDP No. D d EDP No. EDP No. D d

I L Z I L Z
FLAT TiAIN js12 h6 FLAT TiAIN js12 h6

E2753060 EQ753060 6 6 13 57 3 E2753200 EQ753200 20.0 20 38 104 4

E2753080 EQ753080 8 10 19 69 3 E2753250 EQ753250 25.0 25 45 121 5
E2753100 EQ753100 10 10 22 72 4 E2753300 EQ753300 30.0 25 45 121 6
E2753120 EQ753120 12 12 26 83 4 E2753320 EQ753320 32.0 32 53 133 6
E2753140 EQ753140 14 12 26 83 4 E2753350 EQ753350 35.0 32 53 133 6
E2753160 EQ753160 16 16 32 92 4 E2753400 EQ753400 40.0 32 63 155 6
E2753180 EQ753180 18 16 32 92 4

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50
D : MILL DIAMETER
js12 d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 256
 HSS Co8 FINE PITCH, LONG LENGTH, ROUGHING
HSS Co8,

HSS
DIN844
Co8 30
DIN
FINE
1835B p.E258~261
This general purpose rougher is designed for high production metal removal
in a wide range of work piece material. It is suitable for a very broad
spectrum of materials having up to high tensile strength. In many case, the
milled surfaces are of acceptable quality.

Much longer flute than design than E2753 type allows deeper and wider
cutting.

FLAT SHANK E2762 Series Unit : mm

EDP No. EDP No. D d EDP No. EDP No. D d

I L Z I L Z
FLAT TiAIN js12 h6 FLAT TiAIN js12 h6

E2762060 EQ762060 6.0 6 24 68 3 E2762200 EQ762200 20.0 20 75 141 4

E2762070 EQ762070 7.0 10 30 80 3 E2762220 EQ762220 22.0 20 75 141 5
E2762080 EQ762080 8.0 10 38 88 3 E2762240 EQ762240 24.0 25 90 166 5
E2762090 EQ762090 9.0 10 38 88 3 E2762250 EQ762250 25.0 25 90 166 5
E2762100 EQ762100 10.0 10 45 95 4 E2762260 EQ762260 26.0 25 90 166 6
E2762110 EQ762110 11.0 12 45 102 4 E2762280 EQ762280 28.0 25 90 166 6
E2762120 EQ762120 12.0 12 53 110 4 E2762300 EQ762300 30.0 25 90 166 6
E2762130 EQ762130 13.0 12 53 110 4 E2762320 EQ762320 32.0 32 106 186 6
E2762140 EQ762140 14.0 12 53 110 4 E2762350 EQ762350 35.0 32 106 186 6
E2762150 EQ762150 15.0 12 53 110 4 E2762360 EQ762360 36.0 32 106 186 6
E2762160 EQ762160 16.0 16 63 123 4 E2762380 EQ762380 38.0 32 125 217 6
E2762170 EQ762170 17.0 16 63 123 4 E2762938 EQ762938 38.0 40 125 217 6
E2762180 EQ762180 18.0 16 63 123 4 E2762400 EQ762400 40.0 32 125 217 6
E2762190 EQ762190 19.0 16 63 123 4 E2762940 EQ762940 40.0 40 125 217 6

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50
D : MILL DIAMETER
js12 d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 257
 HSS Co8, MULTI FLUTE, ROUGHING - SIDE CUTTING
HSS Co8,

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40
STRENGTH ~ 500N/ 500~800N/ 800~1000N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
6 1800 80 1600 60 1200 55 800 30 4500 200
8 1400 105 1100 75 900 65 560 35 3100 230
10 1100 150 900 120 800 110 450 60 2500 350
12 900 180 800 140 630 110 400 70 2000 400
14 800 180 700 140 560 110 350 70 1800 420
16 700 180 560 140 450 110 280 70 1600 450
18 630 180 500 140 400 110 250 70 1400 470
20 560 180 450 140 400 110 220 70 1200 500
22 500 220 450 170 350 140 220 85 1100 470
25 450 220 400 170 310 140 180 85 1000 450
28 400 210 350 160 280 130 160 85 900 510
30 350 210 310 160 250 130 160 85 900 530
32 350 210 280 160 220 130 140 85 800 500
36 310 210 250 160 200 130 120 85 700 470
40 280 200 220 150 180 120 110 80 630 450
50 220 200 180 170 160 140 90 80 500 370

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

HSS-Co8, MULTI FLUTE, ROUGHING, TiN-COATED - SIDE CUTTING

HSS Co8,

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40
STRENGTH ~ 500N/ 500~800N/ 800~1000N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
6 2200 95 1900 70 1400 65 950 35 5500 240
8 1700 125 1300 90 1000 80 670 40 3700 280
10 1300 180 1000 145 950 130 550 70 3000 420
12 1000 220 950 170 750 130 500 85 2500 480
14 950 220 850 170 670 130 420 85 2200 500
16 850 220 670 170 550 130 340 85 1900 540
18 750 220 600 170 500 130 300 85 1700 560
20 650 220 550 170 500 130 260 85 1400 600
22 600 260 550 200 400 170 260 100 1300 560
25 500 260 500 200 370 170 220 100 1200 540
28 500 250 400 190 340 160 190 100 1100 600
30 400 250 370 190 300 160 190 100 1100 640
32 400 250 340 190 260 160 170 100 950 600
36 370 250 300 190 240 160 140 100 850 560
40 340 240 260 180 220 140 130 95 750 540
50 260 240 220 200 190 170 110 95 600 440

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

E 258
 HSS-Co8, MULTI FLUTE, ROUGHING, TiCN-COATED - SIDE CUTTING
HSS Co8,

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40
STRENGTH ~ 500N/ 500~800N/ 800~1000N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
6 2300 105 2000 80 80 70 1000 40 6000 260
8 1800 135 1400 95 95 85 700 45 4000 300
10 1400 195 1200 155 155 145 600 80 3200 450
12 1200 235 1000 180 180 145 500 90 2600 520
14 1000 235 900 180 180 145 450 90 2300 550
16 900 235 700 180 180 145 350 90 2100 580
18 800 235 650 180 180 145 320 90 1800 610
20 700 235 600 180 180 145 300 90 1600 650
22 650 285 600 220 220 180 300 110 1400 610
25 600 285 500 220 220 180 230 110 1300 580
28 500 275 450 210 210 170 210 110 1200 660
30 450 275 400 210 210 170 210 110 1200 690
32 450 275 350 210 210 170 180 110 1000 650
36 400 275 320 210 210 170 150 110 900 610
40 350 260 300 195 195 155 140 105 800 280
50 300 260 230 220 220 180 120 105 650 480

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

E 259
 HSS-Co8, MULTI FLUTE, FINE, ROUGHING - SIDE CUTTING
HSS Co8,

CARBON STEELS HIGH CARBON STEELS HARDENED STEELS

MEDIUM CARBON STEELS
MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS
ALLOY STEELS
TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40
STRENGTH ~500N/ 500~800N/ 800~1000N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED
6 1800 95 1600 70 1200 65 800 35
8 1400 125 1100 90 900 80 560 40
10 1100 180 900 145 800 130 450 70
12 900 215 800 165 630 130 400 85
14 800 215 700 165 560 130 350 85
16 700 215 560 165 450 130 280 85
18 630 215 500 165 400 130 250 85
20 560 215 450 165 400 165 220 85
22 500 265 450 205 350 165 220 100
25 450 265 400 205 310 165 180 100
28 400 250 350 190 280 155 160 100
30 350 250 310 190 250 155 160 100
32 350 250 280 190 220 155 140 100
36 310 250 250 190 200 155 120 100
40 280 240 220 180 180 145 110 95
50 220 240 180 205 160 170 90 95

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

HSS-Co8, MULTI FLUTE, FINE, ROUGHING, TiN-COATED - SIDE CUTTING

HSS Co8,

CARBON STEELS HIGH CARBON STEELS HARDENED STEELS

MEDIUM CARBON STEELS
MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS
ALLOY STEELS
TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40
STRENGTH ~500N/ 500~800N/ 800~1000N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED
6 2200 115 1900 85 1400 80 950 40
8 1700 150 1300 110 1000 95 670 50
10 1300 215 1000 175 950 155 550 85
12 1000 265 950 205 750 155 500 100
14 950 265 850 205 670 155 420 100
16 850 265 670 205 550 155 340 100
18 750 265 600 205 500 155 300 100
20 650 265 550 205 500 155 260 100
22 600 310 550 240 400 205 260 120
25 500 310 500 240 370 205 220 120
28 500 300 400 230 340 190 190 120
30 400 300 370 230 300 190 190 120
32 400 300 340 230 260 190 170 120
36 370 300 300 230 240 190 140 120
40 340 290 260 215 220 170 130 115
50 260 290 220 240 190 205 110 115

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

E 260
 HSS-Co8, MULTI FLUTE, FINE, ROUGHING, TiCN-COATED - SIDE CUTTING
HSS Co8,

CARBON STEELS HIGH CARBON STEELS HARDENED STEELS

MEDIUM CARBON STEELS
MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS
ALLOY STEELS
TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40
STRENGTH ~500N/ 500~800N/ 800~1000N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED
6 2300 125 2000 95 1600 85 1000 50
8 1800 160 1400 115 1200 100 700 55
10 1400 235 1200 185 1000 175 600 95
12 1200 280 1000 215 800 175 500 110
14 1000 280 900 215 700 175 450 110
16 900 280 700 215 600 175 350 110
18 800 280 650 215 500 175 320 110
20 700 280 600 215 500 175 300 110
22 650 340 600 265 450 215 300 130
25 600 340 500 265 400 215 230 130
28 500 330 450 250 350 205 210 130
30 450 330 400 250 320 205 210 130
32 450 330 350 250 300 205 180 130
36 400 330 320 250 250 205 150 130
40 350 310 300 235 230 185 140 125
50 300 310 230 235 200 215 120 125

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

E 261
 HSS Co8, SHORT LENGTH, ROUGHING & FINISHING
HSS Co8,

HSS
Co8
DIN844 NF DIN
30 1835B p.E266, 267
This general purpose rougher is designed for high production metal removal
in a wide range of work piece material. In many instances, surfaces quality
are of acceptable quality.

FLAT SHANK E2754 Series Unit : mm

EDP No. EDP No. D d EDP No. EDP No. D d

I L Z I L Z
PLAIN TiAIN k10 h6 PLAIN TiAIN k10 h6

E2754060 EQ754060 6 6 13 57 3 E2754180 EQ754180 18 16 32 92 4

E2754070 EQ754070 7 10 16 66 3 E2754200 EQ754200 20 20 38 104 4
E2754080 EQ754080 8 10 19 69 4 E2754220 EQ754220 22 20 38 104 5
E2754090 EQ754090 9 10 19 69 4 E2754250 EQ754250 25 25 45 121 5
E2754100 EQ754100 10 10 22 72 4 E2754280 EQ754280 28 25 45 121 5
E2754110 EQ754110 11 12 22 79 4 E2754300 EQ754300 30 25 45 121 5
E2754120 EQ754120 12 12 26 83 4 E2754320 EQ754320 32 32 53 133 5
E2754130 EQ754130 13 12 26 83 4 E2754360 EQ754360 36 32 53 133 6
E2754140 EQ754140 14 12 26 83 4 E2754400 EQ754400 40 32 63 155 6
E2754160 EQ754160 16 16 32 92 4

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50
D : MILL DIAMETER
k10 d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 262
 HSS Co8, LONG LENGTH ROUGHING & FINISHING
HSS Co8,

HSS
Co8
DIN844 NF DIN
30 1835B p.E266, 267
This general purpose rougher is designed for high production metal removal
in a wide range of work piece material. In many instances, surfaces quality
are of acceptable quality.

Much longer flute than design than E2754 type allows deeper and wider
cutting.

FLAT SHANK E2768 Series Unit : mm

EDP No. EDP No. D d EDP No. EDP No. D d

I L Z I L Z
FLAT TiAIN k10 h6 FLAT TiAIN k10 h6

E2768060 EQ768060 6 6 24 68 3 E2768180 EQ768180 18 16 63 123 4

E2768080 EQ768080 8 10 38 88 4 E2768200 EQ768200 20 20 75 141 4
E2768100 EQ768100 10 10 45 95 4 E2768220 EQ768220 22 20 75 141 5
E2768120 EQ768120 12 12 53 110 4 E2768250 EQ768250 25 25 90 166 5
E2768140 EQ768140 14 12 53 110 4 E2768300 EQ768300 30 25 90 166 5
E2768160 EQ768160 16 16 63 123 4 E2768320 EQ768320 32 32 106 186 5

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50
D : MILL DIAMETER
k10 d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 263
 HSS Co8, 3 FLUTE SHORT LENGTH ROUGHING & FINISHING
HSS Co8,

HSS
Co8
DIN844 NF DIN
30 1835B p.E266, 267
This general purpose rougher is designed for high production metal removal
in a wide range of work piece material. In many instances, surfaces quality
are of acceptable quality.

FLAT SHANK E2766 Series

Unit : mm

EDP No. EDP No. D d EDP No. EDP No. D d

I L Z I L Z
FLAT TiAIN k10 h6 FLAT TiAIN k10 h6

E2766060 EQ766060 6 6 13 57 3 E2766220 EQ766220 22 20 38 104 3

E2766080 EQ766080 8 10 19 69 3 E2766250 EQ766250 25 25 45 121 3
E2766100 EQ766100 10 10 22 72 3 E2766280 EQ766280 28 25 45 121 3
E2766120 EQ766120 12 12 26 83 3 E2766300 EQ766300 30 25 45 121 3
E2766140 EQ766140 14 12 26 83 3 E2766320 EQ766320 32 32 53 133 3
E2766160 EQ766160 16 16 32 92 3 E2766360 EQ766360 36 32 53 133 3
E2766180 EQ766180 18 16 32 92 3 E2766400 EQ766400 40 32 63 155 3
E2766200 EQ766200 20 20 38 104 3

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50
D : MILL DIAMETER
k10 d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 264
 HSS Co8, 3 FLUTE LONG LENGTH ROUGHING & FINISHING
HSS Co8,

HSS
Co8
DIN844 NF DIN
30 1835B p.E266, 267
This general purpose rougher is designed for high production metal removal
in a wide range of work piece material. In many instances, surfaces quality
are of acceptable quality.

Much longer flute than design than E2766 type allows deeper and wider
cutting.

FLAT SHANK E2767 Series Unit : mm

EDP No. EDP No. D d EDP No. EDP No. D d

I L Z I L Z
FLAT TiAIN k10 h6 FLAT TiAIN k10 h6

E2767060 EQ767060 6 6 24 68 3 E2767200 EQ767200 20 20 75 141 3

E2767080 EQ767080 8 10 38 88 3 E2767220 EQ767220 22 20 75 141 3
E2767100 EQ767100 10 10 45 95 3 E2767250 EQ767250 25 25 90 166 3
E2767120 EQ767120 12 12 53 110 3 E2767280 EQ767280 28 25 90 166 3
E2767140 EQ767140 14 12 53 110 3 E2767300 EQ767300 30 25 90 166 3
E2767160 EQ767160 16 16 63 123 3 E2767360 EQ767360 36 32 106 186 3
E2767180 EQ767180 18 16 63 123 3 E2767400 EQ767400 40 32 125 217 3

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50
D : MILL DIAMETER
k10 d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 265
 HSS Co8, MULTI FLUTE, ROUGHING & FINISHING - SIDE CUTTING
HSS Co8,

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40
STRENGTH ~ 500N/ 500~800N/ 800~1000N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
6 1800 65 1600 50 1200 45 800 25 4500 160
8 1400 85 1100 60 900 50 560 30 3100 185
10 1100 120 900 95 800 90 450 50 2500 280
12 900 145 800 110 630 90 400 55 2000 320
14 800 145 700 110 560 90 350 55 1800 340
16 700 145 560 110 450 90 280 55 1600 360
18 630 145 500 110 400 90 250 55 1400 380
20 560 145 450 110 400 90 220 55 1200 400
22 500 175 450 135 350 110 220 70 1100 380
25 450 175 400 135 310 110 180 70 1000 360
28 400 170 350 130 280 105 160 70 900 410
30 350 170 310 130 250 105 160 70 900 420
32 350 170 280 130 220 105 140 70 800 400
36 310 170 250 130 200 105 120 70 700 380
40 280 160 220 120 180 95 110 65 630 360

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

HSS-Co8, MULTI FLUTE, ROUGHING & FINISHING, TiCN-COATED - SIDE CUTTING

HSS Co8,

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40
STRENGTH ~ 500N/ 500~800N/ 800~1000N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
6 2200 80 1900 60 1400 55 950 30 5500 190
8 1700 100 1300 70 1000 60 670 35 3700 220
10 1300 145 1000 115 950 110 550 60 3000 340
12 1000 175 950 130 750 110 500 65 2500 380
14 950 175 850 130 670 110 420 65 2200 410
16 850 175 670 130 550 110 340 65 1900 430
18 750 175 600 130 500 110 300 65 1700 460
20 650 175 550 130 500 110 260 65 1400 480
22 600 210 550 160 400 130 260 85 1300 460
25 500 210 500 160 370 130 220 85 1200 430
28 500 200 400 155 340 125 190 85 1100 490
30 400 200 370 155 300 125 190 85 1100 500
32 400 200 340 155 260 125 170 85 950 480
36 370 200 300 155 240 125 140 85 850 460
40 340 190 260 145 220 115 130 80 750 430

RPM=REVOLUTION PER MIN. Feed=mm / min

The FEED, in long & extra long types, should be reduced by around 50%

E 266
 HSS-Co8, MULTI FLUTE, ROUGHING & FINISHING, TiCN-COATED - SIDE CUTTING
HSS Co8,

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40
STRENGTH ~ 500N/ 500~800N/ 800~1000N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
6 2300 85 2000 65 1600 60 1000 30 6000 210
8 1800 110 1400 80 1200 65 700 40 4000 240
10 1400 155 1200 125 1000 115 600 65 3200 360
12 1200 190 1000 145 800 115 500 70 2600 420
14 1000 190 900 145 700 115 450 70 2300 440
16 900 190 700 145 600 115 350 70 2100 470
18 800 190 650 145 500 115 320 70 1800 500
20 700 190 600 145 500 115 300 70 1600 520
22 650 230 600 175 450 145 300 90 1400 500
25 600 230 500 175 400 145 230 90 1300 470
28 500 220 450 170 350 135 210 90 1200 530
30 450 220 400 170 320 135 210 90 1200 550
32 450 220 350 170 300 135 180 90 1000 520
36 400 220 320 170 250 135 150 90 900 500
40 350 210 300 155 230 125 140 85 800 470

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

E 267
 HSS Co8, MULTI FLUTE, COARSE PITCH, SHORT LENGTH ROUGHING BALL
HSS Co8, ,

HSS
Co8 4~6
30 PLAIN COARSE

This general purpose rougher is designed for high

production metal removal in a wide range of work piece
material. It is recommanded for cutting steel grades and
many non-ferrous materials.

PLAIN SHANK E2806 Series Unit : mm

EDP No. EDP No. d EDP No. EDP No. d

D I L Z D I L Z
PLAIN TiAIN h6 PLAIN TiAIN h6

E2806080 EQ806080 8 8 20 90 4 E2806250 EQ806250 25 25 50 165 4

E2806100 EQ806100 10 10 25 100 4 E2806300 EQ806300 30 25 63 180 6
E2806120 EQ806120 12 12 32 115 4 E2806320 EQ806320 32 25 63 180 6
E2806140 EQ806140 14 12 32 115 4 E2806350 EQ806350 35 32 70 190 6
E2806160 EQ806160 16 16 36 130 4 E2806400 EQ806400 40 32 70 190 6
E2806180 EQ806180 18 16 40 130 4 E2806500 EQ806500 50 42 90 225 6
E2806200 EQ806200 20 20 45 145 4

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

MILL DIA. D : MILL DIAMETER

TOLERANCE d : SHANK DIAMETER
l : LENGTH OF CUT
h6 L : OVERALL LENGTH
Z : No. OF FLUTE

E 268
 HSS-Co8, MULTI FLUTE, ROUGHING , BALL NOSE, TiCN-COATED - SIDE CUTTING
HSS Co8,

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS ALUMINUM

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS ALUMINUM ALLOYS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40
STRENGTH ~ 500N/ 500~800N/ 800~1000N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED RPM FEED
R 4.0 8.0 1400 105 1100 75 900 65 560 35 3100 230
R 5.0 10.0 1100 150 900 120 800 110 450 60 2500 250
R 6.0 12.0 900 180 800 140 630 110 400 70 2000 400
R 8.0 16.0 700 180 560 140 450 110 280 70 1600 450
R 10.0 20.0 560 180 450 140 400 110 220 70 1200 500
R 12.5 25.0 450 220 400 170 310 140 180 85 1000 450
R 16.0 32.0 350 210 280 160 220 130 140 85 800 500
R 20.0 40.0 280 200 220 150 180 120 110 80 630 450

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

E 269
 HSS Co5, 1 FLUTE FOR ALUMINUM
HSS Co5, ,

HSS
Co5 30 PLAIN

Designed for drilling in aluminum, its alloy and non-

ferrous materials.

PLAIN SHANK EL612 Series Unit : mm

MILL SHANK
EDP No. LENGTH OVERALL
DIAMETER DIAMETER
PLAIN OF CUT LENGTH
js14 h6
EL612030 3 8 12 60
EL612040 4 8 12 60
EL612050 5 8 14 60
EL612060 6 8 14 60
EL612070 7 8 14 60
EL612080 8 8 14 80
EL612090 9 8 14 80
EL612100 10 8 14 80

HSS Co5, 1 FLUTE FOR ALUMINUM

HSS Co5, ,

HSS
Co5 30 PLAIN

Designed for drilling in aluminum, its alloy and non-

ferrous materials.

Reduced neck for deeper drilling or deeper located

drilling.

PLAIN SHANK EL612 Series Unit : mm

MILL SHANK LENGTH LENGTH OVERALL NECK

EDP No. DIAMETER DIAMETER OF CUT BELOW SHANK LENGTH DIAMETER
PLAIN d1(js14) d2(h6) L1 L2 L3 d3
EL612904 5 8 18 35 80 4.8
EL612909 5 8 40 40 100
EL612932 8 8 14 68 120 7.5

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

js14

h6

E 270
 HSS CO5, 1 FLUTE
HSS Co5,

HSS
Co5 30 PLAIN

Designed for drilling in general steels.

PLAIN SHANK EL623 Series Unit : mm

MILL SHANK
EDP No. LENGTH OVERALL
DIAMETER DIAMETER
PLAIN OF CUT LENGTH
js14 h6
EL623030 3 8 12 60
EL623040 4 8 12 60
EL623050 5 8 12 60
EL623060 6 8 14 60
EL623070 7 8 14 60
EL623080 8 8 14 80
EL623090 9 8 14 80
EL623100 10 8 14 80

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

js14

h6

E 271
 HSS Co8, SHELL
HSS Co8,

HSS DIN
Co8
DIN841
1880 6-14
30 p.E274

SHELL E2675 Series Unit : mm

MILL WIDTH INTERNAL No.OF

EDP No. DIAMETER OF FACE DIAMETER FLUTE

E2675300 30.0 30.0 13.0 6

E2675350 35.0 35.0 16.0 6
E2675400 40.0 20.0 16.0 8
E2675401 40.0 32.0 16.0 8
E2675402 40.0 40.0 16.0 8
E2675500 50.0 25.0 22.0 8
E2675501 50.0 36.0 22.0 8
E2675502 50.0 50.0 22.0 8
E2675600 60.0 30.0 27.0 8
E2675601 60.0 60.0 27.0 8
E2675630 63.0 40.0 27.0 8
E2675750 75.0 35.0 27.0 10
E2675751 75.0 75.0 27.0 10
E2675800 80.0 45.0 27.0 10
E2675900 90.0 35.0 27.0 10
E2675901 100.0 50.0 32.0 10
E2675902 110.0 35.0 32.0 10
E2675903 125.0 56.0 40.0 12
E2675904 160.0 63.0 50.0 14

Unit : mm

MILL DIA.
TOLERANCE

WIDTH OF FACE
TOLERANCE

INTERNAL DIA.
TOLERANCE

E 272
 HSS Co8, SHELL FOR ALUMINUM
HSS Co8,

HSS DIN
Co8
DIN841
1880 W
42

SHELL E2676 Series Unit : mm

MILL WIDTH INTERNAL No.OF

EDP No. DIAMETER OF FACE DIAMETER FLUTE

E2676300 30.0 30.0 13.0 4

E2676400 40.0 20.0 16.0 4
E2676401 40.0 32.0 16.0 4
E2676402 40.0 40.0 16.0 4
E2676500 50.0 25.0 22.0 6
E2676501 50.0 36.0 22.0 6
E2676502 50.0 50.0 22.0 6
E2676600 60.0 30.0 27.0 6
E2676601 60.0 60.0 27.0 6
E2676630 63.0 40.0 27.0 6
E2676750 75.0 75.0 27.0 6
E2676800 80.0 45.0 27.0 6
E2676901 100.0 50.0 32.0 6

Unit : mm

MILL DIA.
TOLERANCE

WIDTH OF FACE
TOLERANCE

INTERNAL DIA.
TOLERANCE

E 273
 HSS Co8, MULTI FLUTE, FINISH SHELL
HSS Co8,

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40 HRc30~HRc40
STRENGTH 500~800N/ 800~1000N/ 1000~1300N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED
40 240 135 200 120 140 80 80 50
50 200 125 170 105 120 75 70 45
63 150 110 130 95 90 65 50 40
80 120 120 100 100 80 75 40 40
100 100 115 80 95 60 70 30 35
125 80 115 70 95 50 65 20 35
160 60 110 60 100 40 65 20 35

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

E 274
 HSS Co8, ROUGHING SHELL
HSS Co8,

HSS DIN
Co8
DIN841
1880 NR 6-12
COARSE
30

p.E278

ROUGHING SHELL E2677 Series Unit : mm

MILL WIDTH INTERNAL No.OF

EDP No. DIAMETER OF FACE DIAMETER FLUTE

E2677400 40.0 32.0 16.0 6

E2677401 40.0 40.0 16.0 6
E2677500 50.0 36.0 22.0 8
E2677501 50.0 50.0 22.0 8
E2677600 60.0 30.0 27.0 8
E2677601 60.0 60.0 27.0 8
E2677630 63.0 40.0 27.0 8
E2677750 75.0 35.0 27.0 10
E2677751 75.0 75.0 27.0 10
E2677800 80.0 45.0 27.0 10
E2677900 90.0 35.0 27.0 10
E2677901 100.0 50.0 32.0 10
E2677902 110.0 35.0 32.0 12
E2677903 125.0 56.0 40.0 12
E2677904 160.0 63.0 50.0 12

Unit : mm

MILL DIA.
TOLERANCE

WIDTH OF FACE
TOLERANCE

INTERNAL DIA.
TOLERANCE

E 275
 HSS Co8, ROUGHING SHELL
HSS Co8,

HSS DIN
Co8
DIN841
1880 HR 6-12
30 FINE
p.E278

ROUGHING SHELL E2678 Series Unit : mm

MILL WIDTH INTERNAL No.OF

EDP No. DIAMETER OF FACE DIAMETER FLUTE

E2678400 40.0 32.0 16.0 6

E2678401 40.0 40.0 16.0 6
E2678500 50.0 36.0 22.0 8
E2678501 50.0 50.0 22.0 8
E2678600 60.0 30.0 27.0 8
E2678601 60.0 60.0 27.0 8
E2678630 63.0 40.0 27.0 8
E2678750 75.0 35.0 27.0 10
E2678751 75.0 75.0 27.0 10
E2678800 80.0 45.0 27.0 10
E2678900 90.0 35.0 27.0 10
E2678901 100.0 50.0 32.0 10
E2678902 110.0 35.0 32.0 12
E2678903 125.0 56.0 40.0 12
E2678904 160.0 63.0 50.0 12

Unit : mm

MILL DIA.
TOLERANCE

WIDTH OF FACE
TOLERANCE

INTERNAL DIA.
TOLERANCE

E 276
 HSS Co8, ROUGHING & FINISHING SHELL
HSS Co8,

HSS DIN
Co8
DIN841
1880 NF 6-12
NF
30

p.E278

ROUGHING E2679 Series Unit : mm

MILL WIDTH INTERNAL No.OF

EDP No. DIAMETER OF FACE DIAMETER FLUTE

E2679400 40.0 32.0 16.0 6

E2679401 40.0 40.0 16.0 6
E2679500 50.0 36.0 22.0 8
E2679501 50.0 50.0 22.0 8
E2679600 60.0 30.0 27.0 8
E2679601 60.0 60.0 27.0 8
E2679630 63.0 40.0 27.0 8
E2679750 75.0 35.0 27.0 10
E2679751 75.0 75.0 27.0 10
E2679800 80.0 45.0 27.0 10
E2679900 90.0 35.0 27.0 10
E2679901 100.0 50.0 32.0 10
E2679902 110.0 35.0 32.0 12
E2679903 125.0 56.0 40.0 12
E2679904 160.0 63.0 50.0 12

Unit : mm

MILL DIA.
TOLERANCE

WIDTH OF FACE
TOLERANCE

INTERNAL DIA.
TOLERANCE

E 277
 HSS-Co8, MULTI FLUTE ROUGHING SHELL
HSS Co8,

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40 HRc30~HRc40
STRENGTH 500~800N/ 800~1000N/ 1000~1300N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED
40 240 100 200 85 140 60 80 35
50 200 125 170 105 120 75 70 45
63 150 110 130 95 90 65 50 40
80 120 120 100 100 80 75 40 40
100 100 115 80 95 60 70 30 35
125 80 115 70 95 50 65 20 35
160 60 110 60 100 40 65 20 35

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

HSS Co8, MULTI FLUTE, ROUGHING & FINISHING SHELL

HSS Co8,

CARBON STEELS CARBON STEELS CARBON STEELS CARBON STEELS

MATERIAL ALLOY STEELS ALLOY STEELS ALLOY STEELS ALLOY STEELS
TOOL STEELS TOOL STEELS TOOL STEELS TOOL STEELS
HARDNESS ~HRc20 HRc20~HRc30 HRc30~HRc40 HRc30~HRc40
STRENGTH 500~800N/ 800~1000N/ 1000~1300N/ 1000~1300N/
DIAMETER RPM FEED RPM FEED RPM FEED RPM FEED
40 240 100 200 85 140 60 80 35
50 200 125 170 105 120 75 70 45
63 150 110 130 95 90 65 50 40
80 120 120 100 100 80 75 40 40
100 100 115 80 95 60 70 30 35
125 80 115 70 95 50 65 20 35
160 60 110 60 100 40 65 20 35

The FEED, in long & extra long types, should be reduced by around 50% RPM=REVOLUTION PER MIN. Feed=mm / min

E 278
 HSS Co8, 4 FLUTE, CORNER ROUNDING CUTTERS
HSS Co8, ,

R HSS
Co8
DIN
6518 0 FLAT

This general corner rounding end mills are designed for machining fillets on
work piece.

FLAT SHANK E2498 Series Unit : mm

SHANK SHANK
EDP No. RADIUS OUTER OVERALL EDP No. RADIUS OUTER OVERALL
DIAMETER DIAMETER
FLAT H11 DIAMETER LENGTH FLAT H11 DIAMETER LENGTH
h6 h6
E2498010 1.0 8 10 60 E2498085 8.5 25 25 85
E2498015 1.5 9 10 60 E2498090 9.0 26 25 85
E2498020 2.0 10 10 60 E2498095 9.5 27 25 85
E2498025 2.5 11 10 60 E2498100 10.0 28 25 85
E2498030 3.0 12 12 60 E2498105 10.5 31 25 90
E2498035 3.5 13 12 60 E2498110 11.0 32 25 90
E2498040 4.0 14 12 60 E2498120 12.0 34 25 90
E2498045 4.5 15 12 60 E2498125 12.5 41 25 100
E2498050 5.0 16 12 60 E2498130 13.0 42 25 100
E2498055 5.5 19 16 67 E2498140 14.0 44 25 100
E2498060 6.0 20 16 67 E2498150 15.0 46 25 100
E2498065 6.5 21 16 71 E2498160 16.0 48 25 100
E2498070 7.0 22 16 71 E2498180 18.0 52 32 112
E2498075 7.5 23 16 71 E2498200 20.0 56 32 112
E2498080 8.0 24 16 71

Tolerances according to DIN 7160 & 7161 : 1/1000mm

Tolerance range in
Nominal-Diameter in
from 1 to 3 over 3 to 6 over 6 to 10 over 10 to 18 over 18 to 30 over 30 to 50

H11

h6

E 279