= >?

@ABC® ®

Protective Coatings Interline 850

E p o x y P h e n o l i c Surface All surfaces to be coated should be clean, dry and free from contamination. Prior to
W O R L D W I D E P R O D U C T R A N G E
Preparation paint application all surfaces should be assessed and treated in accordance with
ISO 8504:1992.
Product A two component, chemically resistant, high solids, high build epoxy phenolic tank Where necessary, remove weld spatter, and smooth weld seams and sharp edges.
Description lining.
Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning.
Abrasive Blast Cleaning
This product must only be applied to surfaces prepared by abrasive blast cleaning to
Intended Uses To provide corrosion protection for the internals of steel storage tanks containing a a minimum of Sa2½ (ISO 8501-1:1988) or SSPC-SP10.
range of products, including crude oil, unleaded gasoline blends, MTBE, jet fuels,
caustic solutions, and a selected range of aromatic and aliphatic solvents. A sharp, angular surface profile of 50-75 microns (2-3 mils) is recommended.
Interline 850 must be applied before oxidation of the steel occurs. If oxidation does
Certified to occur the entire oxidised area should be reblasted to the standard specified above.
ANSI/NSF Standard
61. NSF Certification Surface defects revealed by the blast cleaning process, should be ground, filled, or
treated in the appropriate manner.
is for tanks greater
than 500 gallons. Where local VOC regulations allow, surfaces may be primed with Interline 850
(thinned 10-15% GTA420) to 40 microns (1.5 mils) dry film thickness before
oxidation occurs. Alternatively, the blast standard can be maintained by use of
dehumidification.
Practical Colour Buff, White & Grey
Application Mixing Interline 850 must be applied in accordance with the Interline 850
Information for
Gloss Level Not applicable system sheet and the detailed International Protective Coatings
Interline 850
Volume Solids 76% Recommended Working Procedures for application of Tank
Linings.
Typical Thickness 100-150 microns (4-6 mils) dry equivalent to Material is supplied in two containers as a unit. Always mix a
132-197 microns (5.3-7.9 mils) wet complete unit in the proportions supplied. Once the unit has been
Theoretical Coverage 6.1 m2/litre at 125 microns d.f.t and stated volume solids mixed it must be used within the working pot life specified.
244 sq.ft/US gallon at 5 mils d.f.t and stated volume solids (1) Agitate Base (Part A) with a power agitator.
(2) Combine entire contents of Curing Agent (Part B) with Base
Practical Coverage Allow appropriate loss factors (Part A) and mix thoroughly with power agitator.
Method of Application Airless spray, Air spray, Brush, Roller Mix Ratio 4 parts : 1 part by volume
Drying Time Working Pot 10°C (50°F) 15°C (59°F) 25°C (77°F) 40°C (104°F)
Overcoating Interval with Life 3 hours 2 hours 1 hour 30 minutes
Interline 850 with Self Airless Spray Recommended - Tip range 0.53-0.68 mm (21-27 thou)
Temperature Touch Dry Hard Dry Minimum Maximum - Total output fluid pressure at spray tip not
less than 176 kg/cm2 (2,500 p.s.i.)
10°C (50°F) 9 hours 24 hours 24 hours 30 days Air Spray Recommended Gun DeVilbiss MBC or JGA
15°C (59°F) 8 hours 20 hours 20 hours 30 days (Pressure Pot) Air cap 704 or 765
25°C (77°F) 5 hours 8 hours 8 hours 30 days Fluid Tip E
40°C (104°F) 3 hours 5 hours 5 hours 21 days Brush Recommended - Typically 50-75 microns (2-3 mils) can be
Small areas only achieved
Roller Recommended - Typically 50-75 microns (2-3 mils) can be
Small areas only achieved
Thinner International GTA420 Do not thin more than allowed by local
Regulatory Flash Point Base (Part A) C/A (Part B) Mixed (or GTA415) environmental legislation.
Data 42°C (108°F) 54°C (129°F) 43°C (109°F)
Cleaner International GTA822
Product Weight 1.54 kg/l (12.85 lb/gal) (or GTA415)
Work Stoppages Do not allow material to remain in hoses, gun or spray equipment.
VOC 212 g/l UK - PG6/23(92), Appendix 3 Thoroughly flush all equipment with International GTA822. Once
units of paint have been mixed they should not be resealed and it
1.88 lb/gal (225 g/l) USA - EPA Method 24 is advised that after prolonged stoppages work recommences with
freshly mixed units.
Clean Up Clean all equipment immediately after use with International GTA822.
It is good working practice to periodically flush out spray
equipment during the course of the working day. Frequency of
cleaning will depend upon amount sprayed, temperature and
elapsed time, including any delays.
Ecotech is an initiative by International Protective Coatings a world leader in coating technology
to promote the use of environmentally sensitive products across the globe. All surplus materials and empty containers should be disposed of in
E E
accordance with appropriate regional regulations/legislation.
N N
G G
0 0
7 7
0 0
0
Page No. 1 of 4 0 Page 2 of 4
 = >?@ABC® ®

Protective Coatings Interline 850

E p o x y P h e n o l i c Surface All surfaces to be coated should be clean, dry and free from contamination. Prior to
W O R L D W I D E P R O D U C T R A N G E
Preparation paint application all surfaces should be assessed and treated in accordance with
ISO 8504:1992.
Product A two component, chemically resistant, high solids, high build epoxy phenolic tank Where necessary, remove weld spatter, and smooth weld seams and sharp edges.
Description lining.
Oil or grease should be removed in accordance with SSPC-SP1 solvent cleaning.
Abrasive Blast Cleaning
This product must only be applied to surfaces prepared by abrasive blast cleaning to
Intended Uses To provide corrosion protection for the internals of steel storage tanks containing a a minimum of Sa2½ (ISO 8501-1:1988) or SSPC-SP10.
range of products, including crude oil, unleaded gasoline blends, MTBE, jet fuels,
caustic solutions, and a selected range of aromatic and aliphatic solvents. A sharp, angular surface profile of 50-75 microns (2-3 mils) is recommended.
Interline 850 must be applied before oxidation of the steel occurs. If oxidation does
Certified to occur the entire oxidised area should be reblasted to the standard specified above.
ANSI/NSF Standard
61. NSF Certification Surface defects revealed by the blast cleaning process, should be ground, filled, or
treated in the appropriate manner.
is for tanks greater
than 500 gallons. Where local VOC regulations allow, surfaces may be primed with Interline 850
(thinned 10-15% GTA420) to 40 microns (1.5 mils) dry film thickness before
oxidation occurs. Alternatively, the blast standard can be maintained by use of
dehumidification.
Practical Colour Buff, White & Grey
Application Mixing Interline 850 must be applied in accordance with the Interline 850
Information for
Gloss Level Not applicable system sheet and the detailed International Protective Coatings
Interline 850
Volume Solids 76% Recommended Working Procedures for application of Tank
Linings.
Typical Thickness 100-150 microns (4-6 mils) dry equivalent to Material is supplied in two containers as a unit. Always mix a
132-197 microns (5.3-7.9 mils) wet complete unit in the proportions supplied. Once the unit has been
Theoretical Coverage 6.1 m2/litre at 125 microns d.f.t and stated volume solids mixed it must be used within the working pot life specified.
244 sq.ft/US gallon at 5 mils d.f.t and stated volume solids (1) Agitate Base (Part A) with a power agitator.
(2) Combine entire contents of Curing Agent (Part B) with Base
Practical Coverage Allow appropriate loss factors (Part A) and mix thoroughly with power agitator.
Method of Application Airless spray, Air spray, Brush, Roller Mix Ratio 4 parts : 1 part by volume
Drying Time Working Pot 10°C (50°F) 15°C (59°F) 25°C (77°F) 40°C (104°F)
Overcoating Interval with Life 3 hours 2 hours 1 hour 30 minutes
Interline 850 with Self Airless Spray Recommended - Tip range 0.53-0.68 mm (21-27 thou)
Temperature Touch Dry Hard Dry Minimum Maximum - Total output fluid pressure at spray tip not
less than 176 kg/cm2 (2,500 p.s.i.)
10°C (50°F) 9 hours 24 hours 24 hours 30 days Air Spray Recommended Gun DeVilbiss MBC or JGA
15°C (59°F) 8 hours 20 hours 20 hours 30 days (Pressure Pot) Air cap 704 or 765
25°C (77°F) 5 hours 8 hours 8 hours 30 days Fluid Tip E
40°C (104°F) 3 hours 5 hours 5 hours 21 days Brush Recommended - Typically 50-75 microns (2-3 mils) can be
Small areas only achieved
Roller Recommended - Typically 50-75 microns (2-3 mils) can be
Small areas only achieved
Thinner International GTA420 Do not thin more than allowed by local
Regulatory Flash Point Base (Part A) C/A (Part B) Mixed (or GTA415) environmental legislation.
Data 42°C (108°F) 54°C (129°F) 43°C (109°F)
Cleaner International GTA822
Product Weight 1.54 kg/l (12.85 lb/gal) (or GTA415)
Work Stoppages Do not allow material to remain in hoses, gun or spray equipment.
VOC 212 g/l UK - PG6/23(92), Appendix 3 Thoroughly flush all equipment with International GTA822. Once
units of paint have been mixed they should not be resealed and it
1.88 lb/gal (225 g/l) USA - EPA Method 24 is advised that after prolonged stoppages work recommences with
freshly mixed units.
Clean Up Clean all equipment immediately after use with International GTA822.
It is good working practice to periodically flush out spray
equipment during the course of the working day. Frequency of
cleaning will depend upon amount sprayed, temperature and
elapsed time, including any delays.
Ecotech is an initiative by International Protective Coatings a world leader in coating technology
to promote the use of environmentally sensitive products across the globe. All surplus materials and empty containers should be disposed of in
E E
accordance with appropriate regional regulations/legislation.
N N
G G
0 0
7 7
0 0
0
Page No. 1 of 4 0 Page 2 of 4
Interline 850 Interline 850
E p o x y P h e n o l i c
E p o x y P h e n o l i c

Product When used as a primer coat applied at 40 microns (1.5 mils) dry film thickness Additional Further information regarding industry standards, terms and abbreviations used in
Characteristics Interline 850 can hold a blast for up to 28 days in the semi-protected environment of Information this data sheet can be found in the following sections of the International Protective
a tank interior. If moisture is present on the surface, oxidation will occur and Coatings data manual:
reblasting will be required. As an alternative, a full coat may be applied, provided
the overcoating intervals are adhered to and all surfaces are correctly cleaned and • Definitions & Abbreviations
prepared prior to overcoating with Interline 850. • Surface Preparation
Do not thin when using Interline 850 for potable water storage
• Paint Application
At temperatures below 15°C (59°F), it is recommended that Interline 850 is allowed
a 15 minute induction period after mixing, prior to commencing application. • Theoretical & Practical Coverage
Maximum film build in one coat is best attained by airless spray. When applying by Individual copies of the following information are available upon request.
methods other than airless spray, the required film build is unlikely to be achieved.
Application by air spray may require a multiple cross spray pattern to attain optimum • Tank Linings Recommended Working Procedures
film build. The use of other methods, e.g. brush or roller, may require more than
one coat and are suggested only for small areas, or initial stripe coating. Safety Precautions This product is intended for use only by professional applicators in industrial
situations in accordance with the advice given on this sheet, the Material Safety Data
Heavily pitted areas should be stripe coated by brush, to ensure good ‘wetting’ of the Sheet and the container(s), and should not be used without reference to the
surface. Material Safety Data Sheet (MSDS) which International Protective Coatings has
Surface temperature must always be a minimum of 3°C (5°F) above dew point. provided to its customers.
For general use, it is not recomended to apply Interline 850 at steel temperatures All work involving the application and use of this product should be performed in
below 10°C (50°F). However for potable water storage only, Interline 850 may be compliance with all relevant national, Health, Safety & Environmental standards and
applied at steel temperatures of 5°C (41°F) and above. Consult International regulations.
Protective Coatings for specific cure schedules.
When applying Interline 850 in confined spaces ensure adequate ventilation. In the event welding or flame cutting is performed on metal coated with this
product, dust and fumes will be emitted which will require the use of appropriate
For multi-coat applications, exposure to low temperatures during, or immediately personal protective equipment and adequate local exhaust ventilation.
after application may result in incomplete cure and surface contamination that
could jeopardise subsequent intercoat adhesion. If in doubt regarding the suitability of use of this product, consult International
This product severely yellows when exposed to sunlight and should not be used on Protective Coatings for further advice.
exteriors where colour is important.
Pack Size 20 litre unit Interline 850 Base 16 litres in a 20 litre container
After the last coat has cured hard, the coating system dry film thickness should be Interline 850 Curing Agent 4 litres in a 5 litre container
measured using a suitable non-destructive magnetic gauge to verify the average total
applied system thickness. The coating system should be free of all pinholes or other 5 gallon unit Interline 850 Base 4 gallons in a 5 gallon container
holidays. The cured film should be essentially free of runs, sags, drips, inclusions or Interline 850 Curing Agent 1 gallon in a 1 gallon container
other defects. All deficiencies and defects should be corrected. The repaired areas
shall be retested and allowed to cure as specified before placing the finished lining For availability of other pack sizes contact International Protective Coatings
into service. Consult International Protective Coatings Tank Linings Working
Procedures for proper repair procedures. Shipping Weight U.N. Shipping No. 1263
Maximum chemical resistance is not attained until the film has completely cured. 20 litre unit 29.0 kg (63.9 lb) Base (Part A) 4.3 kg (9.5 lb) Curing Agent (Part B)
Cure is a function of temperature, humidity and film thickness. Normally films at
250 microns (10 mils) total system dry film thickness will exhibit full and complete 5 gallon unit 27.3 kg (60.4 lb) Base (Part A) 3.9 kg (8.7 lb) Curing Agent (Part B)
cure for optimal chemical resistance in 7-10 days at 25°C (77°F) and 50% relative
humidity. Curing times are proportionately shorter at elevated temperatures and Storage Shelf Life 12 months minimum at 25°C (77°F). Subject to re-inspection
longer at lower temperatures. thereafter. Store in dry, shaded conditions away from sources
of heat and ignition.
Interline 850 is not recommended for storage of aqueous media at temperatures in
excess of 60°C (140°F).
Disclaimer
Interline 850 is not suitable for exposure to acidic conditions. The information given in this sheet is not intended to be exhaustive and any person using the product for any purpose other than that specifically recommended in this sheet
without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. Any warranty, if given, or specific
Terms & Conditions of Sale are contained in International’s Terms & Conditions of Sale, a copy of which can be obtained on request. Whilst we endeavour to ensure that all
This product has the following specification approvals : advice we give about the product (whether in this sheet or otherwise) is correct we have no control over either the quality or condition of the substrate or the many factors affecting
Air BP Specification F2D2 Section 2.1 - Tank Linings. the use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability whatsoever or howsoever arising for the
performance of the product or for any loss or damage (other than death or personal injury resulting from our negligence) arising out of the use of the product. The information
US Military Specification MIL-PRF-4556F. contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development.
DEF stan 80-97 for the lining of bulk aviation fuel tanks. It is the user’s responsibility to check that this sheet is current prior to using the product. Issue date: 20/07/2000
Certified to ANSI/NSF Standard 61. NSF certification is for tanks greater than Copyright © International Paint Ltd. and International are trademarks.
500 gallon, pipes 25 inches in diameter or greater and for valves 2 inches in International Protective Coatings
diameter or greater. Worldwide Availability
Consult International Protective Coatings for specific approved specifications. World Centre Asia Region Australasia Region Europe Region Middle East Region North America Region South America Region
P.O Box 20980 3 Neythal Road 115 Hyde Road P.O Box 20980 PO Box 37 6001 Antoine Drive Av Paiva 999,
Oriel House Jurong Town Yeronga Oriel House Dammam 31411 Houston Neves, Sao Gonçalo,
16 Connaught Place Singapore 628570 Brisbane 16 Connaught Place Saudi Arabia Texas 77091 Rio de Janeiro
Systems This system is self-priming and is not suitable for application over other primers. London, W2 2ZB Queensland London, W2 2ZB Brazil
Interline 850 should only be topcoated with itself, and should never be overcoated England Australia England
Compatibility
with another product. Tel: (44) 20 7479 6000 Tel: (65) 663 3066 Tel: (61) 7 3892 8866 Tel: (44) 20 7479 6000 Tel: (966) 3 812 1044 Tel: (1) 713 682 1711 Tel: (55) 21 624 7100
Fax: (44) 20 7479 6500 Fax: (65) 266 5287 Fax: (61) 7 3892 4287 Fax: (44) 20 7479 6500 Fax: (966) 3 812 1169 Fax: (1) 713 684 1514 Fax: (55) 21 624 7123
Consult International Protective Coatings to confirm that Interline 850 is suitable for H&S (61) 1800 807 001
contact with the product to be stored. Local Office:
Tel: 0191 469 6111 Fax: 0191 495 0676
E E
N N
G G
0 0
7 7
0 0
Page No. 3 of 4 0 Page No. 4 0
Interline 850 Interline 850
E p o x y P h e n o l i c
E p o x y P h e n o l i c

Product When used as a primer coat applied at 40 microns (1.5 mils) dry film thickness Additional Further information regarding industry standards, terms and abbreviations used in
Characteristics Interline 850 can hold a blast for up to 28 days in the semi-protected environment of Information this data sheet can be found in the following sections of the International Protective
a tank interior. If moisture is present on the surface, oxidation will occur and Coatings data manual:
reblasting will be required. As an alternative, a full coat may be applied, provided
the overcoating intervals are adhered to and all surfaces are correctly cleaned and • Definitions & Abbreviations
prepared prior to overcoating with Interline 850. • Surface Preparation
Do not thin when using Interline 850 for potable water storage
• Paint Application
At temperatures below 15°C (59°F), it is recommended that Interline 850 is allowed
a 15 minute induction period after mixing, prior to commencing application. • Theoretical & Practical Coverage
Maximum film build in one coat is best attained by airless spray. When applying by Individual copies of the following information are available upon request.
methods other than airless spray, the required film build is unlikely to be achieved.
Application by air spray may require a multiple cross spray pattern to attain optimum • Tank Linings Recommended Working Procedures
film build. The use of other methods, e.g. brush or roller, may require more than
one coat and are suggested only for small areas, or initial stripe coating. Safety Precautions This product is intended for use only by professional applicators in industrial
situations in accordance with the advice given on this sheet, the Material Safety Data
Heavily pitted areas should be stripe coated by brush, to ensure good ‘wetting’ of the Sheet and the container(s), and should not be used without reference to the
surface. Material Safety Data Sheet (MSDS) which International Protective Coatings has
Surface temperature must always be a minimum of 3°C (5°F) above dew point. provided to its customers.
For general use, it is not recomended to apply Interline 850 at steel temperatures All work involving the application and use of this product should be performed in
below 10°C (50°F). However for potable water storage only, Interline 850 may be compliance with all relevant national, Health, Safety & Environmental standards and
applied at steel temperatures of 5°C (41°F) and above. Consult International regulations.
Protective Coatings for specific cure schedules.
When applying Interline 850 in confined spaces ensure adequate ventilation. In the event welding or flame cutting is performed on metal coated with this
product, dust and fumes will be emitted which will require the use of appropriate
For multi-coat applications, exposure to low temperatures during, or immediately personal protective equipment and adequate local exhaust ventilation.
after application may result in incomplete cure and surface contamination that
could jeopardise subsequent intercoat adhesion. If in doubt regarding the suitability of use of this product, consult International
This product severely yellows when exposed to sunlight and should not be used on Protective Coatings for further advice.
exteriors where colour is important.
Pack Size 20 litre unit Interline 850 Base 16 litres in a 20 litre container
After the last coat has cured hard, the coating system dry film thickness should be Interline 850 Curing Agent 4 litres in a 5 litre container
measured using a suitable non-destructive magnetic gauge to verify the average total
applied system thickness. The coating system should be free of all pinholes or other 5 gallon unit Interline 850 Base 4 gallons in a 5 gallon container
holidays. The cured film should be essentially free of runs, sags, drips, inclusions or Interline 850 Curing Agent 1 gallon in a 1 gallon container
other defects. All deficiencies and defects should be corrected. The repaired areas
shall be retested and allowed to cure as specified before placing the finished lining For availability of other pack sizes contact International Protective Coatings
into service. Consult International Protective Coatings Tank Linings Working
Procedures for proper repair procedures. Shipping Weight U.N. Shipping No. 1263
Maximum chemical resistance is not attained until the film has completely cured. 20 litre unit 29.0 kg (63.9 lb) Base (Part A) 4.3 kg (9.5 lb) Curing Agent (Part B)
Cure is a function of temperature, humidity and film thickness. Normally films at
250 microns (10 mils) total system dry film thickness will exhibit full and complete 5 gallon unit 27.3 kg (60.4 lb) Base (Part A) 3.9 kg (8.7 lb) Curing Agent (Part B)
cure for optimal chemical resistance in 7-10 days at 25°C (77°F) and 50% relative
humidity. Curing times are proportionately shorter at elevated temperatures and Storage Shelf Life 12 months minimum at 25°C (77°F). Subject to re-inspection
longer at lower temperatures. thereafter. Store in dry, shaded conditions away from sources
of heat and ignition.
Interline 850 is not recommended for storage of aqueous media at temperatures in
excess of 60°C (140°F).
Disclaimer
Interline 850 is not suitable for exposure to acidic conditions. The information given in this sheet is not intended to be exhaustive and any person using the product for any purpose other than that specifically recommended in this sheet
without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. Any warranty, if given, or specific
Terms & Conditions of Sale are contained in International’s Terms & Conditions of Sale, a copy of which can be obtained on request. Whilst we endeavour to ensure that all
This product has the following specification approvals : advice we give about the product (whether in this sheet or otherwise) is correct we have no control over either the quality or condition of the substrate or the many factors affecting
Air BP Specification F2D2 Section 2.1 - Tank Linings. the use and application of the product. Therefore, unless we specifically agree in writing to do so, we do not accept any liability whatsoever or howsoever arising for the
performance of the product or for any loss or damage (other than death or personal injury resulting from our negligence) arising out of the use of the product. The information
US Military Specification MIL-PRF-4556F. contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development.
DEF stan 80-97 for the lining of bulk aviation fuel tanks. It is the user’s responsibility to check that this sheet is current prior to using the product. Issue date: 20/07/2000
Certified to ANSI/NSF Standard 61. NSF certification is for tanks greater than Copyright © International Paint Ltd. and International are trademarks.
500 gallon, pipes 25 inches in diameter or greater and for valves 2 inches in International Protective Coatings
diameter or greater. Worldwide Availability
Consult International Protective Coatings for specific approved specifications. World Centre Asia Region Australasia Region Europe Region Middle East Region North America Region South America Region
P.O Box 20980 3 Neythal Road 115 Hyde Road P.O Box 20980 PO Box 37 6001 Antoine Drive Av Paiva 999,
Oriel House Jurong Town Yeronga Oriel House Dammam 31411 Houston Neves, Sao Gonçalo,
16 Connaught Place Singapore 628570 Brisbane 16 Connaught Place Saudi Arabia Texas 77091 Rio de Janeiro
Systems This system is self-priming and is not suitable for application over other primers. London, W2 2ZB Queensland London, W2 2ZB Brazil
Interline 850 should only be topcoated with itself, and should never be overcoated England Australia England
Compatibility
with another product. Tel: (44) 20 7479 6000 Tel: (65) 663 3066 Tel: (61) 7 3892 8866 Tel: (44) 20 7479 6000 Tel: (966) 3 812 1044 Tel: (1) 713 682 1711 Tel: (55) 21 624 7100
Fax: (44) 20 7479 6500 Fax: (65) 266 5287 Fax: (61) 7 3892 4287 Fax: (44) 20 7479 6500 Fax: (966) 3 812 1169 Fax: (1) 713 684 1514 Fax: (55) 21 624 7123
Consult International Protective Coatings to confirm that Interline 850 is suitable for H&S (61) 1800 807 001
contact with the product to be stored. Local Office:
Tel: 0191 469 6111 Fax: 0191 495 0676
E E
N N
G G
0 0
7 7
0 0
Page No. 3 of 4 0 Page No. 4 0