www.DataSheet4U.

net

M201UN02 V.6
Product Specification

( V ) Preliminary Specification
( ) Final Specification

Module 20.1” UXGA Color TFT-LCD

Model Name M201UN02 V6

Checked &
Customer Date Date
Approved by

CC Chiu Feb ,20 , 2006

Approved by Prepared by

Veneo Lin Feb ,20 , 2006

Note: This Specification is subject to change Desktop Display Business Group /

without notice. AU Optronics corporation

Ver0.2 1/24
www.DataSheet4U.net

M201UN02 V.6
Product Specification

i Contents
ii Record of Revision
1.0 Handling Precautions
2.0 General Description
2.1 Display Characteristics
2.2 Functional Block Diagram
2.3 Optical Characteristics
2.4 Pixel format image
3.0 Electrical characteristics
3.1 Absolute Maximum Ratings
3.2 Connectors
3.3 Signal Pin
3.4 Signal Description
3.5 Signal Electrical Characteristics
3.6 Interface Timing
3.6.1 Timing Characteristics
3.6.2 Timing Definition
3.7 Power Consumption
3.8 Power ON/OFF Sequence
4.0 Backlight Characteristics
4.1 Signal for Lamp connector
4.2 Parameter guide line for CCFL Inverter
5.0 Vibration, shock and drop
5.1 Vibration and shock
5.2 Drop test
6.0 Environment
6.1 Temperature and humidity
6.1.1 Operating conditions
6.1.2 Shipping conditions
6.2 Atmospheric pressure
6.3 Thermal shock
7.0 Reliability
7.1 Failure criteria
7.2 Failure rate
7.2.1 Usage
7.2.2 Components de-rating
7.3 CCFL life
7.4 ON/OFF cycle
8.0 Safety
8.1 Sharp edge requirement
8.2 Material
8.2.1 Toxicity
8.2.2 Flammability
8.3 Capacitors
8.4 Hazardous voltage
9.0 Other requirements
9.1 Smoke free design
9.2 National test lab requirement

10.0 Mechanical Characteristics

Ver0.2 2/24
www.DataSheet4U.net

M201UN02 V.6
Product Specification

ii Record of Revision

Version and Date Page Old description New Description Remark

0.1 2006/01/06 All First Edition for Customer All
0.2 2006/02020 7 2.3 Optical Characteristics 2.3 Optical Characteristics
View Angle : View Angle
Min Typ Max Min Typ Max

Horizontal (right) 75 85 - Horizontal (right) 75 89 -

CR=10 (left) 75 85 - CR=10 (left) 75 89 -

Vertical (up) 75 85 - Vertical (up) 75 89 -

CR=10 (down) 75 85 - CR=10 (down) 75 89 -

Color/Chromaticity : Color/Chromaticity
Min Typ Max Min Typ Max

Red x 0.624 0.654 0.684 Red x 0.615 0.645 0.675

Red y 0.301 0.331 0.361 Red y 0.310 0.340 0.370

Green x 0.255 0.285 0.315 Green x 0.260 0.290 0.320

Green y 0.559 0.689 0.619 Green y 0.570 0.600 0.630

Blue x 0.109 0.139 0.169 Blue x 0.112 0.142 0.172

Blue y 0.044 0.074 0.104 Blue y 0.037 0.067 0.097

Ver0.2 3/24
www.DataSheet4U.net

M201UN02 V.6
Product Specification

1.0 Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it.

2) Be sure to turn off power supply when inserting or disconnecting from input connector.

3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.

4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.

5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.

6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.

7) Do not open nor modify the Module Assembly.

8) Do not press the reflector sheet at the back of the module to any directions.

9) In case if a module has to be put back into the packing container slot after once it was taken out from the
container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL
reflector edge softly. Otherwise the TFT module may be damaged.

10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT module.

2.0 11) After installation of the TFT module into an enclosure (Desktop monitor Bezel, for example), do not twist
nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration
that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may
be damaged.

Ver0.2 4/24
www.DataSheet4U.net

M201UN02 V.6
Product Specification
General Description
This specification applies to the 20.1 inch Color TFT-LCD Module M201UN02 v.6.
The display supports the UXGA (1600(H) x 1200(V)) screen format and 16.7M colors (RGB 8-bits data).
All input signals are 2 Channel LVDS interface compatible.
This module does not contain an inverter card for backlight.

2.1 Display Characteristics

The following items are characteristics summary on the table under 25 ℃ condition:

ITEMS Unit SPECIFICATIONS

Screen Diagonal [mm] 510(20.1")
Active Area [mm] 408.0 (H) x 306.0 (V)
Pixels H x V 1600(x3) x 1200
Pixel Pitch [mm] 0.255 (per one triad) x 0.255
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode Normally Black
White Luminance [cd/m2] 300 cd/m2 (Typ)
Contrast Ratio 1000 : 1 (Typ)
Optical Response Time [msec]
( Raising + Falling) 16 (Typ)
( Gray to Gray) 8 (Typ)
Nominal Input Voltage VDD [Volt] +5.0 V
Power Consumption [Watt] 45W(typ.) (w/o Inverter, All white pattern)
(VDD line + CCFL line)
Weight [Grams] 3300 (Max)
Physical Size [mm] 432(W) x 331.5(H) x 25 Max(D)
Electrical Interface Even/Odd R/G/B data, 3 sync signal,
Clock
Support Color 16.7M colors (RGB 8-bit data )
Surface treatment Anti-glare (3H)
Temperature Range
Operating [oC] 0 to +50
Storage (Shipping) [oC] -20 to +60
RoHS Compliance RoHS Compliance

Ver0.2 5/24
www.DataSheet4U.net

M201UN02 V.6
Product Specification

2.2 Functional Block Diagram

The following diagram shows the functional block of the 20.1 inches Color TFT-LCD Module:

AU ASIC
G1
LVDS

Y-Driver IC
LVDS Receiver TFT-LCD
Connector

Timing
1600*(3)*1200
Controlle
Over Pixels
+5V r
Driving G1200
X-Driver IC D4800
D1

6 CCFL

DC/DC Gamma
Converter Correction

I/F + X-PCB
DC POWER
Inverter

Ver0.2 6/24
www.DataSheet4U.net

M201UN02 V.6
Product Specification
2.3 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature):
Item Unit Conditions Min. Typ. Max.
Viewing Angle Horizontal (Right) 89
[degree] 75 -
CR = 10 (Left) 89
[degree]
-
Vertical (Up)
[degree] 75 89 -
CR = 10 (Down)
[degree]
89 -
Contrast ratio Normal Direction 700 1000
Response Time (Note 1) [msec] Raising Time 11
- 15
[msec] Falling Time
- 5 7
[msec] Raising + Falling
- 16 22
[msec] Gray to Gray
- 8
Color / Chromaticity Red x
0.615 0.645 0.675
Coordinates (CIE)
Red y
0.310 0.340 0.370
Green x
0.260 0.290 0.320
Green y
0.570 0.600 0.630
Blue x
0.112 0.142 0.172
Blue y
0.037 0.067 0.097
White x
Color Coordinates (CIE) White 0.283 0.313 0.343
White y
0.299 0.329 0.359
White Luminance at CCFL 7.0mA 2
(central point) [cd/m ] 240 300 -

Luminance Uniformity (Note 2)

[%] 75 80 -
Crosstalk (in 60Hz) (Note 3)
[%] 1.5

Equipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (PR 880, BM-5A ,
BM- 7 , & EZContrast* )
Aperture 1∘with 100cm VD or 2∘with 50cm viewing distance
Test Point Center (ISO point 22)
Environment < 1 lux
LCD Module

PR-880 /
BM5A /
BM7

measuring distance

Module Driving Equipment

‘*’ EZ Contrast is different measurement tool with very close viewing distance.

Ver0.2 7/24
www.DataSheet4U.net

M201UN02 V.6
Product Specification

Note 1: Definition of Response time:

The output signals of photodetector are measured when the input signals are changed from “Full Black” to “Full White”
(rising time), and from “Full White” to “Full Black ”(falling time), respectively. The response time is interval between the
10% and 90% (1 frame at 60 Hz) of amplitudes.

% Tr F Tr R

100
90
Optical
White Black Black White
response
10
0
1 Frame 1 Frame

Tr R (rising time; from “Black” to “White”) + Tf F (Falling time; from “White” to “Black”) = 16ms(typ).

Algorithm:
Level A - Level B ≥ 16
then the average of Grey-to-Grey response time is 8 ms. ( F= 60 Hz).

Note 2: Brightness uniformity of these 9 points is defined as below:

90 % 50 % 10 %

10 %

50 %

90 %

Ver0.2 8/24
www.DataSheet4U.net

M201UN02 V.6
Product Specification

Minimum Luminance in 9 Points (1-9)

Uniformity = ———————————————————
Maximum Luminance in 9 Points (1-9)

Note 3: Crosstalk is defined as below :

1/2 1/6 2/3 1/2 1/3 1/6

1/6
A A’ 1/6
1/3
1/2 1/2
B B’
2/3
184 gray level 184 gray level

0 gray level

Unit: percentage of dimension of display area

l LA-LA’ l / LA x 100%= 1.5% max., LA and LB are brightness at location A and B
l LB-LB’ l / LB x 100%= 1.5% max., LA’ and LB’ are brightness at location A’ and B’

2.4 Pixel format image

Following figure shows the relationship of the input signals and LCD pixel format.

1 2 1599 1600

1st Line R G B R G B R GB R G B

1200
th
Line R G B R G B R GB R G B

Ver0.2 9/24
www.DataSheet4U.net

M201UN02 V.6
Product Specification
3.0 Electrical characteristics
3.1 Absolute Maximum Ratings
Absolute maximum ratings of the module is as following:

Item Symbol Min Max Unit Conditions

Logic/LCD Drive Voltage VIN -0.3 +6.0 [Volt]
Select LVDS data order SELLVDS NC NC [Volt]
CCFL Inrush current ICFLL - 40 [mA] Note 1
CCFL Current ICFL - 8 [mA] rms
Operating Temperature TOP 0 +50 [oC] Note 2
Operating Humidity HOP 8 95 [%RH] Note 2
o
Storage Temperature TST -20 +60 [ C] Note 2
Storage Humidity HST 8 95 [%RH] Note 2

Note 1 : Duration=50 msec.

Note 2 : Maximum Wet-Bulb should be 39℃ and No condensation.

Relative Humidity %
Twb=39℃
T=40℃,H=95%
100
95

80
T=50℃,H=55%

60
T=60℃,H=39%
Storage
40 range Operation T=65℃,H=29%
range
20
Storage
range
5
0
-20 0 50 60
o
Temperature C

Ver0.2 10/2
www.DataSheet4U.net

M201UN02 V.6
Product Specification

3.2 Connectors
Physical interface is described as for the connector on module.

These connectors are capable of accommodating the following signals and will be following components.

Connector Name / Designation Interface Connector / Interface card

Manufacturer JAE or compatible

Type Part Number FI-XB30SSL-HF15 or MDF76TW-30S-1H58

Mating Housing Part Number FI-X30S-H

Connector Name / Designation Lamp Connector / Backlight lamp

Manufacturer YEONHO

Type Part Number 35001HS-02L (2 pins), 20015HS-05L (5 pins)

Mating Type Part Number 35001WR-02L (2 pins), 20015WR-05L (5 pins)

3.3 Signal Pin

Pin# Signal Name Pin# Signal Name

1 RxO0- 2 RxO0+
3 RxO1- 4 RxO1+
5 RxO2- 6 RxO2+
7 GND 8 RxOC-
9 RxOC+ 10 RxO3-
11 RxO3+ 12 RxE0-
13 RxE0+ 14 GND
15 RxE1- 16 RxE1+
17 GND 18 RxE2-
19 RxE2+ 20 RxEC-
21 RxEC+ 22 RxE3-
23 RxE3+ 24 GND
25 NC 26 NC
27 NC 28 Power
29 Power 30 Power

Ver0.2 11/2
www.DataSheet4U.net

M201UN02 V.6
Product Specification

3.4 Signal Description

The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a
differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be
SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels while
the second LVDS port(RxExxx) transmits even pixels.

PIN # SIGNAL NAME DESCRIPTION

1 RxO0- Negative LVDS differential data input (Odd data)
2 RxO0+ Positive LVDS differential data input (Odd data)
3 RxO1- Negative LVDS differential data input (Odd data)
4 RxO1+ Positive LVDS differential data input (Odd data)
5 RxO2- Negative LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
6 RxO2+ Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
7 GND Power Ground
8 RxOC- Negative LVDS differential clock input (Odd clock)
9 RxOC+ Positive LVDS differential clock input (Odd clock)
10 RxO3- Negative LVDS differential data input (Odd data)
11 RxO3+ Positive LVDS differential data input (Odd data)
12 RxE0- Negative LVDS differential data input (Even clock)
13 RxE0+ Positive LVDS differential data input (Even data)
14 GND Power Ground
15 RxE1- Positive LVDS differential data input (Even data)
16 RxE1+ Negative LVDS differential data input (Even data)
17 GND Power Ground
18 RxE2- Negative LVDS differential data input (Even data)
19 RxE2+ Positive LVDS differential data input (Even data)
20 RxEC- Negative LVDS differential clock input (Even clock)
21 RxEC+ Positive LVDS differential clock input (Even clock)
22 RxE3- Negative LVDS differential data input (Even data)
23 RxE3+ Positive LVDS differential data input (Even data)
24 GND Power Ground
25 NC -
26 NC -
27 NC -
28 POWER Power
29 POWER Power
30 POWER Power

Ver0.2 12/2
www.DataSheet4U.net

M201UN02 V.6
Product Specification

Note: Input signals of odd and even clock shall be the same timing.

LVDS DATA Name Description

DSP Display Timing: When the signal is high, the pixel data shall be valid to be displayed
V-S Vertical Sync: Both Positive and Negative polarity are acceptable
H-S Horizontal Sync: Both Positive and Negative polarity are acceptable

TI LVDS X’mitter Module LVDS signal

SN75LVDS83 (interface connector pin7)
Signal Name Low(open)
D0 Red0
D1 Red1
D2 Red2
D3 Red3
D4 Red4
D5 Red7
D6 Red5
D7 Green0
D8 Green1
D9 Green2
D10 Green6
D11 Green7
D12 Green3
D13 Green4
D14 Green5
D15 Blue0
D16 Blue6
D17 Blue7
D18 Blue1
D19 Blue2
D20 Blue3
D21 Blue4
D22 Blue5
D23 NA
D24 H Sync
D25 V Sync
D26 Display Timing
D27 Red6

Ver0.2 13/2
www.DataSheet4U.net

M201UN02 V.6
Product Specification

RxOCLKI
RxOIN0 G0 R5 R4 R3 R2 R1 R0
RxON1 B1 B0 G5 G4 G3 G2 G1
RxOIN2 DE VS HS B5 B4 B3 B2
RxOIN3 RSV B7 B6 G7 G6 R7 R6

RxECLKI
RxEIN0 G0 R5 R4 R3 R2 R1 R0
RxEIN1 B1 B0 G5 G4 G3 G2 G1
RxEIN2 B5 B4 B3 B2
RxEIN3 RSV B7 B6 G7 G6 R7 R6

Note: R/G/B data 7:MSB, R/G/B data 0:LSB

O = “First Pixel Data”
E = “Second Pixel Data”

Ver0.2 14/2
www.DataSheet4U.net

M201UN02 V.6
Product Specification
3.5 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when Vin is off
It is recommended to refer the specifications of SN75LVDS82DGG (Texas Instruments) in detail.

Each signal characteristics are as follows;

Parameter Condition Min Max Unit

Differential InputHigh
Vth 100 [mV]
Voltage(Vcm=+1.2V)

Differential Input Low

Vtl -100 [mV]
Voltage(Vcm=+1.2V)

Note: The value of Vcm from LVDS transmitter should follow the following guide.

Parameter Min Typ. Max Unit

Vcm +1.0 +1.2 +1.35 [V]

3.6 Interface Timings

Basically, interface timings described here is not actual input timing of LCD module but output timing of SN75LVDS82DGG (Texas Instruments) or
equivalent.

3.6.1 Timing Characteristics (DE mode only)

Signal Item Symbol Min Typ Max Unit

Period Tv 1211 1250 1300 Th

Vertical
Active Tdisp(v) 1200 1200 1200 Th
Section

Blanking Tbp(v)+Tfp(v)+PWvs 11 50 100 Th

Period Th 880 1080 1160 Tclk

Horizontal
Active Tdisp(h) 800 800 800 Tclk
Section

Blanking Tbp(h)+Tfp(h)+PWhs 80 280 360 Tclk

Frame Rate Frequency Freq/(Tv x Th) 55 60 75 Hz

Period Tclk 12.0 12.3 17.1 ns

Clock
Frequency Freq 59 81 83 MHz

Ver0.2 15/2
 16/2
M201UN02 V.6

Tv
Vsync
PWvs
Hsync
Tfp(v) Tbp(v) Tdisp(v) Th
DE
Product Specification

N 1 2 3 4 N
Invalid Data Invalid Data
RGB Data
Line Line Line Line Line Line

Ver0.2
CLK

Note :1600X1200 at 60 Hz (VESA STANDARD)

Tclk
Hsync
PWhs
Tbp(h) Tfp(h)
DE
Tdisp(h)
3.6.2 Timing Definition

RGB Data Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
Invalid Data Invalid Data
(Odd) 1 3 7 9 11 M-5 M-3 M-1
RGB Data
Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
(Even) Invalid Data Invalid Data
2 4 6 85 10 12 M-4 M-2 M
www.DataSheet4U.net
www.DataSheet4U.net

M201UN02 V.6
Product Specification
3.7 Power Consumption
Input power specifications are as follows;

Symbol Parameter Min Typ Max Units Condition

VDD Logic/LCD Drive 4.5 5 5.5 [Volt]
Voltage
IDD VDD current 1300 1500 [mA]
IIDD Inrush VDD current 7 [A] t < 80us
PDD VDD Power 6.5 8.3 [Watt] Vin=5V, All White Pattern
VDDrp Allowable 100 [mV]
Logic/LCD Drive p-p
Ripple Voltage
VDDns Allowable 100 [mV]
Logic/LCD Drive p-p
Ripple Noise

3.8 Power ON/OFF Sequence

Vin power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system
shall be Hi-Z state or low level when Vin is off.

90% 90%

Vin 10% 10% 10%

0V

T1 T2 T5 T6 T7

Signal
0V
T3 T4

Lamp
0V

Values
Symbol Unit
Min Typ Max
T1 0.5 - 10 [ms]
T2 0.5 40 50 [ms]
T3 200 - - [ms]
T4 200 - - [ms]
T5 0.5 16 50 [ms]
T6 0.5 - 10 [ms]
T7 1000 - - [ms]

Ver0.2 17/2
www.DataSheet4U.net

M201UN02 V.6
Product Specification
4.0 Backlight Characteristics

4.1 Signal for Lamp connector

Connector No. Pin No. Color Function

1 Pink High Voltage (Lamp 1)
2 Sky Blue High Voltage (Lamp 3)
CN2 3 NC NC

Upper 4 Red Low Voltage (Lamp 1)

5 Dark Blue Low Voltage (Lamp 3)
1 White High Voltage (Lamp 2)
CN3
2 White Low Voltage (Lamp 2)
1 White High Voltage (Lamp 5)
CN4
2 White Low Voltage (Lamp 5)
1 Pink High Voltage (Lamp 6)

Lower 2 Sky Blue High Voltage (Lamp 4)

CN5 3 NC NC
4 Red Low Voltage (Lamp 6)
5 Dark Blue Low Voltage (Lamp 4)

Ver0.2 18/2
www.DataSheet4U.net

M201UN02 V.6
Product Specification
4.2 Parameter guide line for CFL Inverter

Symbol Parameter Min Typ Max Units Condition

ISCFL CCFL standard current 4.0 7.0 8.0 [mA] (Ta=25oC)

rms
IRCFL CCFL operation range 6.5 7.0 7.5 [mA] (Ta=25oC)
rms
fCFL CCFL Frequency 40 55 70 [KHz] (Ta=25oC)
Note 1

ViCFL CCFL Ignition Voltage 1600 [Volt] (Ta=0oC)

(0oC) Note 4 rms Note 2
ViCFL CCFL Ignition Voltage 1230 [Volt] (Ta=25oC)
(25oC) Note 4 rms Note 2
VCFL CCFL Discharge Voltage 744 [Volt] (Ta=25oC)
(Reference) 820 rms Note 3
@7mA
PCFL CCFL Power consumption 31.3 [Watt] (Ta=25oC)
37
@7mA Note 3

Note 1: CCFL Frequency should be carefully determined to avoid interference between inverter and TFT LCD
Note 2: CCFL inverter should be able to give out a power that has a generating capacity of over 1700 voltage.
Lamp units need 1700 voltage minimum for ignition
Note 3: Calculator value for reference (ICFL×VCFLx6=PCFL)
Note 4: (measure for both end of lamp wire)

5.0 Vibration, Shock, and Drop

5.1 Vibration & Shock

Vibration mode Random

Acceleration (Grms) 1.5
Frequency (Hz) 10~200
Active time (min) 30 for each axis (X, Y, Z)

5.2 Shock Test Spec:

Acceleration (G) –a 50
Active time -b 20
Wave form half-sin
Times 1

Direction: ±X , ±Y, ±Z

Ver0.2 19/2
www.DataSheet4U.net

M201UN02 V.6
Product Specification
5.3 Drop test
Package test: The drop height is 60 cm.

6.0 Environment
The display module will meet the provision of this specification during operating condition or after storage or
shipment condition specified below. Operation at 10% beyond the specified range will not cause physical
damage to the unit.

6.1 Temperature and Humidity

6.1.1 Operating Conditions
The display module operates error free, when operated under the following conditions;
Temperature 0 0C to 50 0C
Relative Humidity 8% to 95%
Wet Bulb Temperature 39.0 0C

6.1.2 Shipping Conditions

The display module operates error free, after the following conditions;
Temperature -20 0C to 60 0C
Relative Humidity 8% to 95%
Wet Bulb Temperature 39.0 0C

6.2 Atmospheric Pressure

The display assembly is capable of being operated without affecting its operations over the pressure range as
following specified;

Pressure Note
Maximum Pressure 1040hPa 0m = sea level
Minimum Pressure 674hPa 3048m = 10.000 feet
Note : Non-operation attitude limit of this display module = 30,000 feet. = 9145 m.

6.3 Thermal Shock

The display module will not sustain damage after being subjected to 100 cycles of rapid temperature change.
A cycle of rapid temperature change consists of varying the temperature from -200C to 600C, and back again.

Thermal shock cycle -20 0C for 30min 60 0C for 30min

Power is not applied during the test. After temperature cycling, the unit is placed in normal room ambient for at
least 4 hours before powering on.

7.0 Reliability
This display module and the packaging of that will comply following standards.

7.1 Failure Criteria

The display assembly will be considered as failing unit when it no longer meets any of the requirements stated
in this specification. Only as for maximum white luminance, following criteria is applicable.
Note : Maximum white Luminance shall be 150 cd/m 2or more.

Ver0.2 20/2
www.DataSheet4U.net

M201UN02 V.6
Product Specification

7.2 Failure Rate

The average failure rate of the display module (from first power-on cycle till 1,000 hours later) will not exceed 1.0%.
The average failure rate of the display module from 1,000 hours until 16,000 hours will not exceed 0.7%
per 1000 hours.

7.2.1 Usage
The assumed usage for the above criteria is:
220 power-on hours per month
500 power on/off cycles per month
Maximum brightness setting
Operation to be within office environment (250C typical)

7.2.2 Component De-rating

All the components used in this device will be checked the load condition to meet the failure rate criteria.

7.3 CCFL Life

The assumed CCFL Life will be longer than 50,000 hours, typical value is 50,000 hours under stable condition at 25 ±
5oC;
Standard current at 7.0 ± 0.5mA.
Definition of life: brightness becomes 50% or less than the minimum luminance value of CCFL.

7.4 ON/OFF Cycle

The display module will be capable of being operated over the following ON/OFF Cycles.

ON/OFF Value Cycles

+Vin and CCFL power 30,000 10 seconds on / 10 seconds off

8.0 Safety

8.1 Sharp Edge Requirements

There will be no sharp edges or comers on the display assembly that could cause injury.

8.2 Materials
8.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they
will be reviewed and approved by the responsible AUO Toxicologist.

Ver0.2 21/2
www.DataSheet4U.net

M201UN02 V.6
Product Specification
8.2.2 Flammability
All components including electrical components that do not meet the flammability grade UL94-V1 in
the module will complete the flammability rating exception approval process. The printed circuit board
will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on
the printed circuit board.

8.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being
inserted backwards.

9.0 Other requirements

9.1 National Test Lab Requirement

The display module will satisfy all requirements for compliance to

UL 1950, First Edition U.S.A. Information Technology Equipment

CSA C22.2 No.950-M89 Canada, Information Technology Equipment
EEC 950 International, Information Technology Equipment
EN 60 950 International, Information Processing Equipment
(European Norm for IEC950)
9.2 Label
9.2.1 Product label

10.0 Mechanical Characteristic

Ver0.2 22/2
www.DataSheet4U.net

Product Specification M201UN02 V6

AU OPTRONICS CORPORATION

document version 0.4 23/24

www.DataSheet4U.net

Product Specification M201UN02 V6

AU OPTRONICS CORPORATION

document version 0.4 24/24