Scribd
Upload
102 views4 pages

Carbon Copy Mini Analog Delay

This pedal is a mini analog delay pedal that packs the warmth and tone of the original Carbon Copy Analog Delay into a smaller housing. It has controls for modulation on/off, number of repeats, mix of wet and dry signal, delay time, and accentuating the high frequencies. It is powered by a 9-volt adapter and has a 1M ohm input and 1k ohm output impedance.

Uploaded by

Jeffrey MacFarlane
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
102 views4 pages

Carbon Copy Mini Analog Delay

This pedal is a mini analog delay pedal that packs the warmth and tone of the original Carbon Copy Analog Delay into a smaller housing. It has controls for modulation on/off, number of repeats, mix of wet and dry signal, delay time, and accentuating the high frequencies. It is powered by a 9-volt adapter and has a 1M ohm input and 1k ohm output impedance.

Uploaded by

Jeffrey MacFarlane
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

M299

Carbon Copy ®

Mini Analog Delay

This pedal packs the organic analog warmth and


ease of use of the original Carbon Copy Analog
Delay into an MXR mini housing with added sonic
versatility so that you can make the most out of
your pedalboard real estate.

jimdunlop.com/m299
External Controls

2 4

1 MOD switch toggles modulation on/off (orange LED indicates on)


2 REGEN knob sets number of repeats
3 MIX knob controls blend of wet and dry signals
4 DELAY knob sets time between repeats
5 FOOTSWITCH toggles effect on/bypass (blue LED indicates on)
6 BRIGHT switch accentuates delay signal's high end frequencies (blue LED indicates on)

M299 | Carbon Copy® Mini Analog Delay 2


Basic Operation

Power

The Carbon Copy® Mini Analog Delay is powered by the


Dunlop ECB003 9-volt adapter or the DC Brick™, Iso-Brick™,
and Mini Iso-Brick™ power supplies. This pedal cannot be
powered by a battery.

Directions

1  un a cable from your guitar to M299’s INPUT jack and another


R
cable from M299’s OUTPUT jack to your amplifier.
2  tart with all knobs set to 12 o’clock.
S
3 Turn effect on by depressing the footswitch.
4 Rotate REGEN knob clockwise to increase number of repeats or
counterclockwise to decrease it.
5  otate MIX knob clockwise to increase ratio of wet to dry signal
R
or counterclockwise to decrease it. Fully clockwise results in
half wet/half dry mix while fully counterclockwise results in
100% dry signal.
6  otate DELAY knob clockwise to increase delay time or
R
counterclockwise to decrease it.
7  se a jeweler’s flathead screwdriver to flip the BRIGHT switch
U
toward heel of pedal to accentuate delay signal’s high end
frequencies (indicated by blue LED).
8  ush in MOD switch to add modulation to your delay signal.
P
Modulation width and speed can be adjusted internally (remove
bottom plate) with a 3mm slotted screwdriver (see Diagram A).

DIAGRAM A

M299 | Carbon Copy® Mini Analog Delay 3


Specifications

Input Impedance 1MΩ

Output Impedance 1kΩ

Max Input Level +5 dBV, 500 Hz

Max Output Level +8 dBV

Noise Floor**

Mix at Max CW -96 dBV

Mix at Max CCW -104 dBV

Delay Distortion <1%, 1 kHz -5 dBV Input

Delay Time 20 ms to 600 ms

Noise Reduction 2:1 ratio

Modulation Speed 0.2 Hz to 2.2 Hz

Bypass True Hardwire

Current Draw 26 mA

Power Supply 9 volts DC

*Regen at max CCW, A-weighted

M299 | Carbon Copy® Mini Analog Delay 4

You might also like