Deep Cycle VRLA Battery FCD12-200AT

GENERAL FEATURES APPLICATIONS

¾ Environmentally friendly ¾ Solar & Wind energy system

¾ Thick plate with high Tin low ¾ Cable TV Systems
Calcium alloy ¾ Telecom systems
¾ High Reliability and Good Quality ¾ Wheel chair & Golf Car
¾ Deep Discharge Recovery ¾ Marine Equipment
¾ High Power Density ¾ Railway Systems
¾ Long Service Life, in Float or Cyclic ¾ Emergency Power System

DIMENSIONS & WEIGHT TECHNICAL SPECIFICATIONS

Length(mm) 532±1 Nominal Voltage 12V(6 cells per unit)

Width(mm) 206±1 Design Floating Life @25℃ 12 Years
Heighth(mm) 215±1 Nominal Capacity @25℃(20 hour rate@10.00A,10.50V) 200Ah

Total Heighth(mm) 219±1 10 hour rate (18.20A,10.8V) 182.0Ah

Capacity @25℃ 5 hour rate (31.80A,10.5V) 159.0Ah
Weight(kg) 58.4±3%
1 hour rate (111.2A,9.6V) 111.2Ah
532 206
208 96 Internal Resistance Full Charged Battery@25℃ ≤3.4mΩ
Discharge -20℃~50℃
Ambient Temperature Charge -20℃~50℃
219
215

Storage -20℃~50℃
Max.Discharge Current@25℃ 2000A(5s)
Terminal 40℃ 102%
Unit: mm
Φ18 Capacity affected by
4 25℃ 100%
Temperature
0℃ 85%
M8 (10 hr Capacity )
-15℃ 65%

Self-Discharge@25℃ per Month 3%

COMPLIED STANDARDS
Initial Charging Current Less than 36A
IEC 60896-21/22 JIS C8704 Standby Use
Charge (Constant Voltage 13.6-13.8V
YD/T799 BS6290 part4
Voltage) @25℃ Initial Charging Current Less than 36A
GB/T 19638 UL 1989 Cycle Use
Voltage 14.4-14.9V

BATTERY DISCHARGE TABEL

Discharge Constant Current per Cell (Amperes at 25°C)

F.V/Time 15min 30min 45min 1h 2h 3h 5h 8h 10h 20h 100h
1.60V 257.4 164.4 120.8 111.2 70.6 49.6 33.6 22.2 19.80 10.60 2.40
1.67V 252.8 161.4 118.6 109.0 69.2 48.6 33.0 21.8 19.40 10.40 2.36
1.70V 248.0 158.4 116.4 107.0 68.0 47.8 32.4 21.4 19.00 10.20 2.30
1.75V 243.4 155.4 114.2 105.0 66.6 46.8 31.8 21.0 18.80 10.00 2.26
1.80V 234.0 149.4 109.8 101.0 64.0 45.0 30.6 20.2 18.20 9.90 2.22
Discharge Constant Power per Cell (Watts at 25°C)
F.V/Time 15min 30min 45min 1h 2h 3h 5h 8h 10h 20h 100h
1.60V 495.4 316.4 232.6 213.4 135.6 95.2 64.8 42.6 38.2 20.7 4.62
1.67V 486.4 310.6 228.2 209.6 133.2 93.6 63.6 42.0 37.4 20.2 4.52
1.70V 477.4 304.8 224.0 205.6 130.8 91.8 62.4 41.2 36.8 20.1 4.44
1.75V 468.4 299.0 219.8 201.8 128.2 90.0 61.2 40.4 36.0 19.8 4.36
1.80V 450.4 287.6 211.4 194.0 123.4 86.6 59.0 38.8 34.6 19.2 4.28
Note The above data are average values, and can be obtained within 3 charge/discharge cycles. These are not minimum values. Cell and battery
designs/specifications are subject to modification without notice. Contact MCA for the latest information.

Copyright©2017 MCA Battery Manufacture Co.,Ltd. Page 1/2

 Deep Cycle VRLA Battery FCD12-200AT
PERFORMANCE CHARACTERISTICS
erformance Characteristics
Charging characteristics Discharge characteristics(@25℃/77°F)
Charging
Volume

Voltage
Current

@25℃/77°F 13.20

（%） （A） （V） 12.60

Charging voltage:13.65±0.10V/piece

Voltage（V）
120 0.12C 15.00 12.00
charging volume
100 0.10C 14.40 11.40
10.80
80 0.08C 13.80 0.10C 0.05C
0.55C 0.25C 0.17C
charging voltage 10.20
60 0.06C 13.20 9.60
2C 1C

40 0.04C 12.60 9.00

After 100% Discharge
After 50% Discharge 8.40
20 0.02C 12.00
charging current
0 1 5 10 20 30 60 2 3 5 10 20
0 0
0 4 8 12 16 20 24 28 32 36 min h

Charging time（hour） Discharging time（hour）

Temperature effect on Design Service life Cycle life vs.Depth of discharge

@25°C/77°F
25

20
Capacity %

15
Life year

10
100%DOD 50%DOD 30%DOD
5
Float charging voltage：13.65±0.01V

0 10 20 30 40 50 60
Temperature（°C） Cycle life（times）

Temperature effect Temperature effect on capacity

on battery self-discharge 120
Residual capacity（%）

0.05CA
0.10CA
120 100
Capacity（%）

0.20CA
100
80
0.55CA
80
0°C/32°F 60 1.00CA
10°C/50°F
60 2.0CA
20°C/68°F 40
40
40°C/104°F 30°C/86°F 20
20
0
-30 -25 -20 -15 -10 -5 0 5 10 15 20 25 30 35 40
0 2 4 6 8 10 12 14 16 18 20
Storage time（month） Temperature（°C）

BATTERY CONSTRUCTION

Positive Container Pillar

Component Negative plate Safety valve Terminal Separator Electrolyte
plate &Cover seal
Balanced Female Two
Thick high Flame Advanced AGM
Pb-Ca grid for ABS Copper Dilute high layers
Sn low Ca Si-Rubbeand separator for
Features improved (UL94-V0 Insert purity sulphuric epoxy
grid with aging high pressure
recombination optional) M8(torque:7 acid resin
special paste resistancer cell design
efficiency ~9N.m) seal

MCA Battery Manufacture Co.,Ltd.

Cangjiang Industrial Estate Gaoming District Foshan City China
Tel：+86‐757‐66752600 Fax：+86‐757‐66752601 HTTP：//WWW.MCABATTERY.COM

Copyright©2017 MCA Battery Manufacture Co.,Ltd. Page 2/2