95mm

Remote Buttons description: Because different only valid on Lock and unlcok doors functions. Note II: JP2 hand brake needle cap shall be detected when remote start engine.
2)Pressing" "button for 3 seconds, the siren will sound once, PKE function When JP2 hand brake needle cap in (SS-0n) position means that the hand brake
remotes are with different button icons,please is pulled and the vehicle can be started normally; JP2 hand brake needle cap in
will be temporarily turn off, one push start engine function turn off , press the" "
refer to the real remotes.
LC680PKE One push I.PKE Remote button icons:
button once to turn on one push start engine function.
NOTE: This function is suitable for washing or repairing the vehicle。
(SS-0ff) position means that the hand brake is not pulled well and the system is
not allowed to start the car; The factory default JP2 pin cap is on the (SS-ON)
position.
4.Search
start Instructions Press" " button once, the siren will sound 15 times, easy to locate the cars. 3.Central door lock automation:
① When driving, all doors are closed. Press the "unlock" or "lock" button to unlock
Arm (Lock) Disarm (Unlock) Select Search or lock the system, but the car alarm system will not be triggered.
III.Functions Instruction ② During driving, all doors are closed. After 5 seconds, press foot brake, and the
1.PKE inductive automatic door lock and unlock:
doors will be locked automatically,
II.Button function: 1) Turn off the car engine, when the car owner leaves the cars to about 2-3 meters
③ After parking and turning off the key, the door lock will be unlock automatically
105mm

1.Arm (Lock) with the remote controls, the siren will sound once, the central door lock system
to facilitate passengers to get on and off.
1)Press the button " " once, then the siren will sound once, the central control will be locked automatically.
4. Auto Lock :
lock door will be locked, the push start button function will be disabled, and the 2)When the car owners are close to the cars about 2-3 meters, the car siren will
The owner leaves the car with the remote control for about 2 to 3 meters (away
car can not start. sound twice, the central door lock system will be unlocked, one push start engine
from the PKE range), press unlock button to disarm the system. After 5 seconds,
2)Press and hold the " " for three seconds; the car engine will begin to warm function turn on.
the siren will sound once, the central lock will be locked, the one push start button
up for 15 minutes and the siren will sound once. After the engine start for 5 NOTE: The central control door lock system is only for negative trigger connection,
function will be off.
seconds,the central door will be locked, the siren would sound once. and other connection modes need additional relays.
5.LED Indicator :
3)After the remote start engine successfully, press and hold the " " for 3 seconds, 2, Remote start engine:
① warning status: LED warning light, flash twice in one second.
the engine will turn off, the siren will sound once, . after 5 seconds, the central On brain unit, JP2 pin on SS-ON position, pressing LOCK button for 3 seconds ,
the siren will sound once, after ACC output 0.5 seconds, ON1, ON2 (Air ② Disarm status: LED warning light is not on
control door lock will be locked again and the siren will sound once.
conditioner) start outputs, the ACC, ON2 (Air conditioner) quit after 0.5 seconds, ③ Alarm status: LED warning light flash quickly
2.Disarm (Unlock)
1)Press" " button once, the siren will sound twice, the central door lock will be and STR start ignition 0.8 seconds, if start engine successfully, one push start ④ code learning status, the LED warning light is on for a long time.
unlocked, one push start function is on, press push button can start the car engine. indicator will be on, the car engine will be turn on after 15 minutes. 6.Illegal trigger alarm
2)Pressing the" " button for 3 seconds, the siren will sound for 3 times, the 2). If the car engine can not start, the ACC, ON2 (Air conditioner) quit after 0.5 In arm status, When the foot brake is illegally triggered, the system will briefly
trunk will be released. seconds, STR start ignition 12 seconds, if not start successfully, the system will stop and alarming for 30 seconds. If it is triggered all the time, the system will
3.Select continue the third start, the start time will be increased to be 17 seconds. automatically stop detecting the foot brake switch after 6 cycles until the foot
1) Press" " button once,the siren will sound once, the siren sounds function Note I: there is a start cycle (three times) for each operation startup. If the startup brake switch returns to normal.
is on, repeat this operation to turn off the siren sounds function. This selection is not successful after three times, it is necessary to restart the operation.

7.Emergency disarm switch: V.One push start engine Instructions Preparation before installation: Original car chip coil
When the remote control is lost or the car alarm system cannot be disarmed for Please refer to the below steps:

ACC
Please refer to the below steps:
other reasons, the owner can forcibly open the door with the key, find the Before installation, you should first confirm whether the one-button start module
emergency disarm switch, press it continuously for 10 times within 12 seconds, 1.Step on the foot brake and short press 2.Step on the brake and short press for accessories are complete, and confirm that the electrical performance of the
and the siren will sound briefly twice to temporarily remove the arm status. Press push button 1 second to start engine: 1 second to cut off engine; vehicle is working properly. If there is any abnormality, please contact the service
the one button start button to start the car within 2 minutes. If the one button start center first to ensure correct installation. Original car chip
ENGINE ENGINE
button is not pressed to start the car engine after 2 minutes, the siren will sound START
STOP
START
STOP Tools preparation: small awl, electrician's knife, electric pen, wire stripper, Phillips
briefly after 2 minutes, The system will lock again and return to the arm status. screwdriver, electrician tape, electric drill, etc. Original car chip processing and installation
8. PKE remote control weak battery reminder: Original car chip processing and installation
When the battery is in normal state, the indicator light is blue when the remote The first step is to put out the original car chip, usually a small rectangular black
controller works. When the battery voltage is lower than the rated value, the Operations: step on the foot brake and Operations: when the engine is turned body as shown in the figure
press the push button for one second. on, step on the brake and then short
indicator light is red when the remote controller works. press the push button for 1 second to The second step is to remove the induction coil at the lock of the original car.
The button indicator will light up after
9.Learning code: engine start. turn off the engine. After the engine is The third step is to bound the removed chip and the induction coil of the lock with
In disarm status, long press the emergencydisarm switch for more than 3 seconds, turned off, the button indicator will be off. tape
and the LED indicator light is on for 10 seconds. The system enters the code The fourth step is to install the processed coil and chip together inside the
learning mode. At the same time, press the "ARM” + "DISARM" buttons of the 3.To convert between ACC ON and panel 4.Long pressing to start enginein dash-board and then stabilized.
remote control for more than 1 second, the LED indicator light flash once, and the ON without stepping on the brake. special case: Another easy installation method is to directly paste the chip to the induction coil
1 2 at the lock position
siren sounds once, indicating that the remote control ID has been written into the ENGINE
START

brain unit memory. Press the second remote control, and the LED indicator light ENGINE
START
OFF ACC ON STOP
Picture 1 Picture 2 Picture 3
3
STOP
goes off, Indicates that the second remote control code has been learned.
Maximum total of two remote controls can be learned. key hole
Instructions for One button Start System :
Note: when learning each remote control, the system will automatically increase When the original car with steering wheel lock and anti-theft chip lock, the original Half key blank
Operations: Long pressing can protect
the learning time by 10 seconds. After learning two remote controls or pressing Operations: No pressing brake, short the motor for 3 seconds. car's steering wheel lock and chip lock must be released before the application.
the emergency disarm switch again, you can exit the learning status. press for 1 second to turn on the ACC If the engine cannot be started at a lower
audio, short press again for 1 second To release the steering wheel lock, a key blank inserted into the lock hole as
temperature or the motor is in bad
to turn on the dash-board, short press condition, step on the brake and long shown in Figure 2 and turn to ON position. Installation diagram for original steering wheel:
again to turn off the system, it can be pressing the push button to start the To Unlock the anti-theft chip, as shown in Figure 3, bind the original car remote The first step is to insert the key into the lock and saw it off. Leave 1 cm to extend
cycled operation, at this time, the button engine, then release hands after the
indicator would flash. control and the induction coil together. it and you can take it out at any time with pliers.
engine started.
Secondly is to drill a small hole next to the lock with a drill of the same size as the

4 5 6 7

wire diameter to facilitate the start of the button threading

The next step is to remove the small iron piece on the start button and paste
it on the negative head position with glue.
After installation, unplug the original car's starter plug to prevent the car from
consuming electricity when the key is unlocked.
Another note: Another easy installation method is to directly remove the lock
head as a whole.
Installation instructions for vehicles that need to be started by
stepping on the clutch:
1. If the clutch needs to be stepped on when the vehicle is started, then the
clutch and brake must be stepped on at the same time, so the push button
can start successfully.
2. For the original vehicle that need to be started by stepping on the brake
or clutch, then the relay must be pretended to supply power to the brake or
clutch when the remote control starts. The principle is to simulate someone
stepping on the brake or clutch in the car.

One Push button Car Lock STR

Lock ON1

Lock ACC

Lock Air Condition ON2

12V battery
Red
Rough Yellow

Rough Brown
Siren
8 Rough Blue

Rough Purple
Black
12V Footbrake Light
Pink
Red/black
–Trunk output
Orange
Siren

Grey
Start input
White -Lock output
White/Black
-Unlock output
Technical parameters:
Without hand brake

With hand brake

1.Working voltage: 12V ± 3V Reset Switch

2.Static current： 17-19mA

3. PKE sensing distance: ≥ 3m LED Light PKE Antenna 1

4. RF receiving distance: ≥ 70m

5. Working current: Siren: + / - 10A;
Open trunk: - 250mA; Unlocking: - 250mA; Lock: - 250mA;
PKE Antenna 2
ACC output: + 30A on1 total electrical output: + 30A;
STR output: + 30A; On2 (air conditioning) output: + 30A.
6. PKE low frequency: 125kHz ± 0.3 kHz
7. RF operating frequency: 433.92mhz ± 0.3mhz
8. Operating temperature: - 40 ° C to + 85 ° C
433.92 attenna