Print-Toyota Service Information 11/3/17, 6(42 pm

Print Exit

1GD-FTV LUBRICATION OIL PUMP INSTALLATION

CAUTION / NOTICE / HINT

NOTICE:
· When replacing the parts in the following chart (A), replace the No. 1 injection pipe sub-assembly, No. 2
injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.
Replaced Parts (A) Pipes Requiring New Replacement

· Injector assembly (including shuffling the

injector assemblies between the
· No. 1 injection pipe sub-assembly
cylinders)
· No. 2 injection pipe sub-assembly
· Common rail assembly
· Cylinder head sub-assembly

· Supply pump assembly

· Common rail assembly
· Cylinder block sub-assembly
· Cylinder head sub-assembly Fuel inlet pipe sub-assembly
· Cylinder head gasket
· Timing chain case assembly

· After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet
pipe sub-assembly, clean them with a brush and compressed air.
· The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or
dropped.
· Make sure foreign matter does not enter the fuel path.
· The supply pump assembly is a precision instrument. Do not use the supply pump assembly if it is struck
or dropped.
· Hold the supply pump assembly itself during removal and installation. Do not hold the pre-stroke control
valve or fuel pipe, etc.

PROCEDURE

1.INSTALL TIMING CHAIN CASE ASSEMBLY AND ENGINE WATER PUMP ASSEMBLY 11310

a. Apply a light coat of engine oil to the 4 new O-rings.

b. Install the 4 O-rings to the cylinder block sub-assembly and cylinder head sub-assembly.

c. Clean and degrease the contact surfaces of the timing chain case assembly, cylinder head sub-assembly
and cylinder block sub-assembly.

d. Apply a coating of seal packing to the timing chain case assembly at the points shown in the illustration.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 1 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

*a 46 mm (1.81 in.) *b 50 mm (1.97 in.)

*c 2.0 to 3.0 mm (0.0787 to 0.118 in.) *d 2.5 to 3.5 mm (0.0984 to 0.138 in.)
*e 3.0 to 4.0 mm (0.118 to 0.158 in.) *f 1.5 to 2.5 mm (0.0591 to 0.0984 in.)
*g 13 to 15 mm (0.512 to 0.591 in.) *h 9.0 to 11 mm (0.354 to 0.433 in.)
*i 31 to 33 mm (1.22 to 1.30 in.) - -

Seal packing:
for line area D:
Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent.
for line area A-A, B-B, C-C and E:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.

Seal Packing Application Specification:

Seal Packing Seal Packing
Line Type and Area Application Area
Diameter Application Length

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 2 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

Dashed Line 1.5 to 2.5 mm (0.0591 2.0 to 3.0 mm (0.0787 -

to 0.0984 in.) to 0.118 in.)
2.5 to 3.5 mm (0.0984 2.0 to 3.0 mm (0.0787
A-A 46 mm (1.81 in.)
to 0.138 in.) to 0.118 in.)
2.5 to 3.5 mm (0.0984 2.0 to 3.0 mm (0.0787
B-B 50 mm (1.97 in.)
to 0.138 in.) to 0.118 in.)
1.5 to 2.5 mm (0.0591 3.0 to 4.0 mm (0.118 to
D -
to 0.0984 in.) 0.158 in.)

NOTICE:
· Using non-residue solvent, clean and remove any oil from the installation surface.
· Install the part within 3 minutes and tighten the bolts within 10 minutes after applying seal
packing.
· Do not add engine oil for at least 2 hours after installation.
· Do not start the engine within 2 hours after installation.

e. Temporarily install the timing chain case assembly with the 15 bolts.

*a Type of bolt *b Tightening

Bolt Length:
Thread
Item Length
Diameter
30 mm (1.18 8.0 mm (0.315
Bolt A
in.) in.)
45 mm (1.77 8.0 mm (0.315
Bolt B
in.) in.)
65 mm (2.56 8.0 mm (0.315
Bolt C
in.) in.)
30 mm (1.18 10 mm (0.394
Bolt D
in.) in.)

f. Temporarily install a new gasket and the engine water pump assembly with the 8 bolts.

g. Tighten the 23 bolts in the order shown in the illustration.

Torque:
for bolt A, B and C : 25 N*m (255 kgf*cm, 18 ft.*lbf)
for bolt D : 43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 3 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

Check the torque of bolt 1 after tightening bolt 23.

2.INSTALL INJECTION PUMP INSULATOR 22815A

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

3.INSTALL SUPPLY PUMP ASSEMBLY 22100

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

4.INSTALL NO. 1 CHAIN TENSIONER SLIPPER 13559

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

5.TEMPORARILY INSTALL NO. 1 CHAIN VIBRATION DAMPER 13561

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

6.INSTALL CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH 13506
NO. 1 CHAIN SUB-ASSEMBLY

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

7.TIGHTEN NO. 1 CHAIN VIBRATION DAMPER 13561

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

8.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY 13540

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

9.INSTALL SUPPLY PUMP SHAFT NUT

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

10.INSTALL CAMSHAFT TIMING SPROCKET 13523

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

11.INSTALL NO. 2 CHAIN VIBRATION DAMPER 13562

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

12.INSTALL NO. 2 CHAIN SUB-ASSEMBLY 13507

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

13.INSTALL NO. 2 CHAIN TENSIONER SLIPPER 13559

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

14.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY 13550

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

15.INSTALL TIMING CHAIN GUIDE 13566B

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>CAMSHAFT>INSTALLATION

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 4 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

16.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

17.INSTALL OIL PUMP DRIVE GEAR 13519

a. Install the oil pump drive gear to the crankshaft.

18.INSTALL TIMING CHAIN COVER PLATE 11324

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SUPPLY PUMP>INSTALLATION

19.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY 11302

a. Apply a light coat of engine oil to a new timing chain case gasket.

b. Install the timing chain case gasket to the timing chain case assembly.

c. Clean and degrease the contact surfaces of the timing chain cover sub-assembly and timing chain case
assembly.

d. Apply a coating of seal packing to the timing chain cover sub-assembly at the points shown in the
illustration.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 5 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

*a 2.0 to 3.0 mm (0.0787 to 0.118 in.) *b 2.5 to 3.5 mm (0.0984 to 0.138 in.)

Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.

Standard seal packing diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)

NOTICE:
· Using non-residue solvent, clean and remove any oil from the installation surface.
· Install the part within 3 minutes and tighten the bolts within 10 minutes after applying seal
packing.
· Do not add engine oil for at least 2 hours after installation.
· Do not start the engine within 2 hours after installation.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 6 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

e. Temporarily install the timing chain cover sub-assembly with the 20 bolts.

*a Type of bolt *b Tightening

Bolt Length:
Thread
Item Length
Diameter
40 mm (1.57 8.0 mm (0.315
Bolt A
in.) in.)
25 mm (0.984 8.0 mm (0.315
Bolt B
in.) in.)

f. Tighten the 20 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:
Check the torque of bolt 1 after tightening bolt 20.

20.INSTALL FRONT CRANKSHAFT OIL SEAL 11303A

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>FRONT CRANKSHAFT OIL

SEAL>INSTALLATION

21.INSTALL OIL PAN SUB-ASSEMBLY 12101

a. Clean and degrease the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 7 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

b.

Seal Packing

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Standard seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)

NOTICE:
· Remove any oil from the contact surface.
· Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes
after applying seal packing.
· Do not add engine oil within 2 hours after installation.
· Do not start the engine for at least 2 hours after installation.

c.

Bolt

Nut

Install the oil pan sub-assembly to the cylinder block sub-assembly with the 23 bolts and 2 nuts.
Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 8 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

NOTICE:
Check the torque of all nuts and bolts labeled A again.

22.INSTALL ENGINE OIL LEVEL SENSOR 89491

Click hereEngine / Hybrid System>1GD-FTV LUBRICATION>OIL LEVEL SENSOR>INSTALLATION

23.INSTALL OIL PAN COVER SILENCER 12144

a. Install the oil pan cover silencer to the oil pan sub-assembly with the 5 bolts.
Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

24.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY 11201

a. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

b. Install a new cylinder head cover gasket, No. 2 cylinder head cover gasket and 2 camshaft bearing cap oil
hole gaskets to the cylinder head cover sub-assembly.

c. Clean and degrease the contact surfaces of the cylinder head cover sub-assembly and cylinder head sub-
assembly.

d. Apply seal packing as shown in the illustration.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 9 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

*1 Timing Chain Cover Sub-assembly *2 Timing Chain Case Assembly

*3 Cylinder Head Sub-assembly *4 No. 3 Camshaft Bearing Cap

*a Seal Diameter: 3.0 to 6.0 mm (0.118 to 0.236 *b Application Width: 7.0 mm (0.276 in.)
in.)
*c Application Width: 9.0 mm (0.354 in.) *d Application Width: 11.0 mm (0.433 in.)

Seal packing:
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Standard seal diameter:

3.0 to 6.0 mm (0.118 to 0.236 in.)

NOTICE:
· Remove any oil from the contact surface.
· Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 10
minutes after applying seal packing.
· Do not add engine oil for at least 2 hours after installation.
· Do not start the engine within 2 hours after installation.

e.

Bolt

Nut

Nozzle Holder Clamp Seat

Tighten the 14 bolts, 4 nozzle holder clamp seats, 2 nuts and camshaft position sensor in the order shown
in the illustration.
Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
· When reusing the camshaft position sensor, check the O-rings.
· Make sure that the O-ring is not cracked or jammed when installing it on the cylinder head cover
sub-assembly.
· Replace with a new part if it is dropped or if it receives a strong impact.
· Check the torque of bolts 1 to 4 again.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 10 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

25.INSTALL NOZZLE HOLDER GASKET 23682

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>INSTALLATION

26.TEMPORARILY INSTALL INJECTOR ASSEMBLY 23670

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>INSTALLATION

27.INSTALL GENERATOR BRACKET SUB-ASSEMBLY 12501

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

28.INSTALL NO. 1 ENGINE HANGER 12281A

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

29.INSTALL NO. 1 WATER HOSE CLAMP BRACKET (w/ DPF) 16575C

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

30.INSTALL CRANKSHAFT PULLEY 13471

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>FRONT CRANKSHAFT OIL

SEAL>INSTALLATION

31.INSTALL CRANKSHAFT PULLEY COVER 13496

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>FRONT CRANKSHAFT OIL

SEAL>INSTALLATION

32.INSTALL VISCOUS HEATER CRANKSHAFT PULLEY (w/ Viscous Heater) 88451B

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>FRONT CRANKSHAFT OIL

SEAL>INSTALLATION

33.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY 16620

a. Install the V-ribbed belt tensioner assembly to the timing chain cover sub-assembly with 3 bolts.
Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

34.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY 16603

a. Install the No. 1 idler pulley sub-assembly to the generator bracket sub-assembly with the bolt.
Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

35.INSTALL THERMOSTAT 16331A

Click hereEngine / Hybrid System>1GD-FTV COOLING>THERMOSTAT>INSTALLATION

36.INSTALL WATER INLET 16321

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

https://toyotamanuals.com.au/docs/hilux-service-repair-manual-…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 11 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

37.INSTALL WATER OUTLET SUB-ASSEMBLY 16304

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

38.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY 16207

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

39.TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY 15407

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/

TURBOCHARGER>INSTALLATION

40.TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB- 17141

ASSEMBLY

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/

TURBOCHARGER>INSTALLATION

41.INSTALL TURBO OIL OUTLET PIPE 15474

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/

TURBOCHARGER>INSTALLATION

42.TEMPORARILY INSTALL TURBOCHARGER STAY 17293

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/

TURBOCHARGER>INSTALLATION

43.TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY 17141

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/

TURBOCHARGER>INSTALLATION

44.TIGHTEN TURBOCHARGER STAY 17293

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/

TURBOCHARGER>INSTALLATION

45.INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous 87101

Heater)

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

46.CONNECT NO. 1 AND NO. 2 TURBO WATER HOSE 16284

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/

TURBOCHARGER>INSTALLATION

47.INSTALL NO. 1 WATER BY-PASS PIPE 16268

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

48.INSTALL NO. 3 WATER BY-PASS PIPE 16279

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/

TURBOCHARGER>INSTALLATION

49.INSTALL PCV HOSE (except Cold Area Specification Vehicles) 12261

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/

https://toyotamanuals.com.au/docs/hilux-service-repair-manual…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 12 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

TURBOCHARGER>INSTALLATION

50.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY 25051

· w/ DPF:
Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/
DPF)>INSTALLATION
· w/o DPF:
Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/o
DPF)>INSTALLATION

51.INSTALL NO. 2 EXHAUST PIPE SUPPORT STAY

· w/ DPF:
Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/
DPF)>INSTALLATION
· w/o DPF:
Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/o
DPF)>INSTALLATION

52.INSTALL NO. 1 TURBO INSULATOR 17271

· w/ DPF:
Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/
DPF)>INSTALLATION
· w/o DPF:
Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/o
DPF)>INSTALLATION

53.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR 17167

· w/ DPF:
Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/
DPF)>INSTALLATION
· w/o DPF:
Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/o
DPF)>INSTALLATION

54.INSTALL AIR FUEL RATIO SENSOR (w/ DPF) 89467B

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>AIR FUEL RATIO SENSOR>INSTALLATION

55.INSTALL NO. 1 INJECTOR HOLDER (w/ DPF) 23295D

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION

INJECTOR>INSTALLATION

56.CONNECT NO. 4 WATER BY-PASS HOSE (w/ DPF) 16281

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION

INJECTOR>INSTALLATION

57.INSTALL NO. 5 WATER BY-PASS HOSE (w/ DPF) 16282

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION

INJECTOR>INSTALLATION

58.INSTALL PCV PIPE (for Cold Area Specification Vehicles) 12229

https://toyotamanuals.com.au/docs/hilux-service-repair-manual…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 13 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/

TURBOCHARGER>INSTALLATION

59.INSTALL IDLER PULLEY ASSEMBLY (w/o Air Conditioning System) 16630D

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

60.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning 88431

System)

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

61.INSTALL HOSE BRACKET 44781

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

62.TEMPORARILY INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY 23701

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>INSTALLATION

63.TIGHTEN INJECTOR ASSEMBLY 23670

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>INSTALLATION

64.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY 23701

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>INSTALLATION

65.INSTALL WIRING HARNESS CLAMP BRACKET

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

66.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY 23760

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>INSTALLATION

67.INSTALL NO. 1 FUEL PIPE (w/ DPF) 23811H

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION

INJECTOR>INSTALLATION

68.INSTALL WIRING HARNESS CLAMP BRACKET

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>INSTALLATION

69.INSTALL INTAKE MANIFOLD 17111

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSTALLATION

70.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY 23770

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSTALLATION

71.INSTALL FUEL INLET PIPE SUB-ASSEMBLY 23804C

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSTALLATION

72.INSTALL NO. 3 FUEL PIPE (w/ DPF) 23815D

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSTALLATION

https://toyotamanuals.com.au/docs/hilux-service-repair-manual…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 14 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

73.INSTALL NO. 4 FUEL PIPE SUB-ASSEMBLY (w/ DPF) 23804D

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSTALLATION

74.INSTALL NO. 1 FUEL HOSE 23271H

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SUPPLY PUMP>INSTALLATION

75.INSTALL NO. 2 FUEL HOSE 23273H

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SUPPLY PUMP>INSTALLATION

76.INSTALL FUEL PUMP MOTOR WIRE 23243B

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SUPPLY PUMP>INSTALLATION

77.INSTALL FUEL INJECTION PUMP COVER SUB-ASSEMBLY 22803

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SUPPLY PUMP>INSTALLATION

78.INSTALL MANIFOLD STAY 17118

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSTALLATION

79.INSTALL WIRING HARNESS CLAMP BRACKET

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSTALLATION

80.INSTALL NO. 2 FUEL PIPE 23812D

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

81.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE 11409

Click hereEngine / Hybrid System>1GD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD>INSTALLATION

82.INSTALL NO. 1 EGR COOLER AND NO. 2 EGR VALVE ASSEMBLY WITH ELECTRIC 25800
EGR CONTROL VALVE ASSEMBLY

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR COOLER>INSTALLATION

83.INSTALL NO. 4 WATER BY-PASS PIPE SUB-ASSEMBLY 16209

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

84.INSTALL VACUUM CONTROL VALVE SET 25804

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR VALVE>INSTALLATION

85.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY 25601

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

86.INSTALL CONNECTING WIRE 27148A

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

87.INSTALL NO. 3 WATER BY-PASS PIPE SUB-ASSEMBLY 16206B

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR COOLER>INSTALLATION

https://toyotamanuals.com.au/docs/hilux-service-repair-manual…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 15 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

88.INSTALL NO. 2 EGR PIPE 25612

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR VALVE>INSTALLATION

89.INSTALL EGR VALVE BRACKET 25625

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR VALVE>INSTALLATION

90.INSTALL DIESEL TURBO PRESSURE SENSOR 89421C

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>MANIFOLD ABSOLUTE PRESSURE

SENSOR>INSTALLATION

91.INSTALL GAS FILTER 23265C

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR VALVE>INSTALLATION

92.INSTALL ENGINE COVER BRACKET 12631A

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE UNIT>INSTALLATION

93.INSTALL PIPE CLAMP (w/ DPF) 17578B

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/

DPF)>INSTALLATION

94.TEMPORARILY INSTALL NO. 2 VACUUM PIPE (w/ DPF) 25734

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/

DPF)>INSTALLATION

95.TEMPORARILY INSTALL NO. 1 VACUUM PIPE (w/ DPF) 25733A

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/

DPF)>INSTALLATION

96.TIGHTEN NO. 2 VACUUM PIPE (w/ DPF) 25734

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/

DPF)>INSTALLATION

97.TIGHTEN NO. 1 VACUUM PIPE (w/ DPF) 25733A

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>MONOLITHIC CONVERTER(w/

DPF)>INSTALLATION

98.INSTALL EXHAUST GAS TEMPERATURE SENSOR (w/ DPF) 89425

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EXHAUST GAS TEMPERATURE

SENSOR>INSTALLATION

99.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ DPF) 89481B

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>DIFFERENTIAL PRESSURE

SENSOR>INSTALLATION

100.INSTALL NO. 2 WATER BY-PASS PIPE 16278

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR VALVE>INSTALLATION

https://toyotamanuals.com.au/docs/hilux-service-repair-manual…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 16 of 17
Print-Toyota Service Information 11/3/17, 6(42 pm

101.INSTALL DIESEL THROTTLE BODY ASSEMBLY 26100G

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>INSTALLATION

102.INSTALL INTERCOOLER AIR TUBE 17363K

Click hereEngine / Hybrid System>1GD-FTV ENGINE CONTROL>DIESEL THROTTLE BODY>INSTALLATION

103.INSTALL ENGINE WIRE 82121

104.INSTALL NO. 2 ENGINE COVER BRACKET 12632

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR VALVE>INSTALLATION

105.INSTALL NO. 2 HOSE TO HOSE TUBE 44763C

Click hereEngine / Hybrid System>1GD-FTV EMISSION CONTROL>EGR VALVE>INSTALLATION

106.INSTALL ENGINE ASSEMBLY

Click hereEngine / Hybrid System>1GD-FTV ENGINE MECHANICAL>ENGINE ASSEMBLY>INSTALLATION

© 2012 TOYOTA MOTOR CORPORATION. All Rights Reserved.

https://toyotamanuals.com.au/docs/hilux-service-repair-manual…anual/repair/contents/RM100000000M7TG.html?PUB_TYPE=RM&MODE=1 Page 17 of 17