MITSUBISHI

ENGINE
4D68 (E - W)
WORKSHOP MANUAL

FOREWORD

This Workshop Manual contains procedures for Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

removal, disassembly, inspection, adjustment,
11A
reassembly and installation, etc. for service
mechanics.
All information, illustrations and product
descriptions contained in this manual are current
as at the time of publication. We, however, reserve
the right to make changes at any time without
prior notice or obligation.

FILING INSTRUCTION
Please keep these manual pages in the binder
No. BN890001.
File these pages according to the signs
“Added”, “Revised” and “Deleted” on the “List
of effective pages” which are interpreted
below.
Added:
File the pages with this sign additionally in
your manual.
Revised, Deleted:
Replace the existing pages with the
corresponding pages with this sign.

Missing sheets will be supplied upon request.

Pub. No. PWEE9609

E Mitsubishi Motors Corporation Dec. 1996
 INTRODUCTION

EXPLANATION OF MANUAL CONTENTS

Maintenance and Servicing Procedures

(1) A diagram of the component parts is D Removal steps:

provided near the front of each section in The part designation number corresponds
order to give the reader a better under- to the number in the illustration to indicate
standing of the installed condition of removal steps.
component parts. D Disassembly steps:
(2) The numbers provided within the diagram The part designation number corresponds
indicate the sequence for maintenance and to the number in the illustration to indicate
servicing procedures. disassembly steps.
: Indicates a non-reusable part. D Installation steps:
The tightening torque is provided where Specified in case installation is impossible
applicable. in reverse order of removal steps. Omitted
if installation is possible in reverse order
of removal steps.
D Reassembly steps:
Specified in case reassembly is impossible
in reverse order of disassembly steps.
Omitted if reassembly is possible in reverse
order of disassembly steps.

Classification of Major Maintenance/Service Points

When there are major points relative to maintenance and servicing procedures
(such as essential maintenance and service points, maintenance and service stan-
dard values, information regarding the use of special tools, etc.), these are
arranged together as major maintenance and service points and explained in
detail.
AA" : Indicates that there are essential points for removal or disassembly.
"AA : Indicates that there are essential points for installation or reassembly.

Symbols for Lubrication, Sealants and Adhesives

Information concerning the locations for : Grease (multipurpose grease unless

lubrication and for application of sealants there is a brand or type specified)
and adhesives is provided, by using sym-
bols, in the diagram of component parts, or : Sealant or adhesive
on the page following the component parts
page, and explained. : Brake fluid, automatic transmission fluid
or air conditioner compressor oil

: Engine oil or gear oil

E Mitsubishi Motors Corporation Dec. 1996 PWEE9609

 INTRODUCTION

Indicates the Indicates the Indicates the Indicates the Indicates the
group title. section title. group number. section num- page number.
ber.

4G68 ENGINE (E- W) - Water Pump, Thermostat, Hose and Pipes 11A-7-1
7. WATER PUMP, THERMOSTAT, HOSE AND PIPES
REMOVAL AND INSTALLATION
16 Nm
1 2 Denotes non-reusable part.
17
3
4 18
22 Nm

8
45 Nm 9 Nm
Denotes tightening
5 19 23 Nm
torque.
7 23 Nm 20
11 Nm
12 Nm 16 6 10

15 22 12 Nm

9 21
35 Nm

11
14 This number corresponds to
the number appearing in
12 19 Nm “Removal steps”,
“Disassembly steps”,
“Installation steps” or
“Reassembly steps”.
13
13 Nm
Removal steps
1. Eyebolt 12. Water pump
2. Gasket 13. Water pump gasket
3. Oil pipe "DA 14. O-ring
4. Gasket "DA 15. Water inlet pipe
5. Eyebolt "DA 16. O-ring
6. Gasket 17. Vacuum pump
7. Oil return pipe 18. O-ring
8. Oil return hose 19. Water inlet fitting
9. Engine coolant temperature sensor "CA 20. Thermostat
"FA 10. Engine coolant temperature gauge "BA 21. Water outlet fitting
unit "AA 22. Thermostat housing Operating procedures, cau-
"EA 11. Cover tions, etc. on removal, installa-
INSTALLATION SERVICE POINTS tion, disassembly and reas-
"AA THERMOSTAT HOUSING INSTALLATION sembly are described.
(1) Apply a 3 mm bead of form-in-place gasket (FIPG) to
the mounting surface.
Specified sealant:
Mitsubishi Genuine Part No. MD970389 or
equivalent.

DEN0768
E Mitsubishi Motors Corporation Dec. 1996 PWEE9609

Issue date Publication number-Revision code

E Mitsubishi Motors Corporation Dec. 1996 PWEE9609

NOTES

E Mitsubishi Motors Corporation Dec. 1996 PWEE9609