Industrial Training Report Format
1. Cover Page (color print)
2. Inner Pages
a) Certificate by Company/Industry
b) Declaration by student
c) Acknowledgement
3. About Company/Industry
4. Table of Contents
5. List of Tables
6. List of Figures
7. Abbreviations and Nomenclature (If any)
8. Chapters
1 Introduction (An overview of the whole report)
2 Formal Training provided (if applicable) [This section
describes the training provided through formal classroom training
environment. Brief description of each training session and its benefit
towards the training program]
3 Industrial Training [The section should describe the following:
Objectives
Tools & Technology Used
Techniques studied in different Departments
Software and Tools Used
Highlights of Training Exposure (area, scope)]
4 Problem Identification/Case Study (Discussions)
5 Recommendations
9. References
10.Data Sheet(If any)
11. Appendices ( If any) Snapshots
INSTRUCTIONS FOR TRAINING REPORT
1. A chapter may be further divided into several divisions and sub- divisions
depending on type & volume of work.
2. The training report must be submitted in One Copy duly signed by the Faculty
Facilitator & HOD. Students should also submit the soft copy of report and
Power Point presentation.
3. The length of the training report may be about 25 to 30 page.
4. The training report shall be computer typed (English- British, Font - Times
Roman, Size-12 point) and printed on A4 size paper.
5. The training report should be Spiral bound.
6. The training report shall be typed with 1.5 line spacing with a margin 3.5 cm
on the left, 2.5 cm on the top, and 1.25 cm on the right and at bottom.
Every page in the report must be numbered. The page numbering, starting
from declaration by student and till the beginning of the introductory chapter,
should be printed in small Roman numbers, i.e, i, ii, iii, iv...... The page
number of the first page of chapter 1 should be numbered as 1, 2,3,4,5...
All printed page numbers should be located at the bottom centre of the page.
7. In the training report, the title (cover) page should be given first and printed in
black letters.
8. The table of contents should list all headings and sub-headings. The title page
and certificates will not find a place among the items listed in the Table of
Contents. One and a half line spacing should be adopted for typing the matter
under this head.
9. The list of tables should use exactly the same captions as they appear above
the tables in the text. One and a half spacing should be adopted for typing the
matter under this head.
10. The list of figures should use exactly the same captions as they appear below
the figures in the text. One and a half spacing should be adopted for typing
the matter under this head.
11. The list of symbols, abbreviation & nomenclature should be typed with one
and a half line spacing. Standard symbols, abbreviation etc should be used.
12. Subject matter must be typed on single side of the page. 13.All
the pages must be numbered properly.
INDUSTRIAL TRAINING REPORT
(Times New Roman, 24 pt. Bold)
DEPARTMENT OF ELECTRICAL ENGINEERING
(Times New Roman, 16 pt. Bold)
Submitted in partial fulfillment of
the Requirements for the award of
Degree of Bachelor of Technology in Electrical Engineering
Submitted By (14 size)
Name:
University Roll No.: Semester/Branch:
(Times New Roman, 14 pt. Bold)
SUBMITTED TO:
Department of Electrical Engineering (16 size)
ISLAMIC UNIVERSITY OF SCIENCE AND
TECHNOLOGY AWANTIPORA, J&K
CERTIFICATE
(16 Times New Roman, bold)
This is to certify that Mr. / Ms. has partially completed /
completed / not completed the Minor/ Major Industrial Training during the period from
to in our Organization / Industry as a Partial Fulfillment of Degree of
Bachelor of Technology in eLECTRICAL Engineering. He / She was trained in the
field of
.
Signature & Seal of Training Manager
Note: Xerox copy of the certificate issued from the Training company
need to be attached instead of this page.
DECLARATION (16 Times New Roman)
I hereby declare that the Industrial Training Report on Name of the Department/ Section,
Industry is an authentic record of my own work as requirements of Minor/ Major
Industrial Training during the period from to for the award of degree of
B.Tech. (Electrical Engineering), O P Jindal Institute of Technology, Raigarh (C.G.),
under the guidance of (Name of Faculty Facilitator) (12 size)
(Signature of student)
(Name of Student)
(University Roll
Date: No.)
Certified that the above statement made by the student is correct to the best of our
knowledge and belief
Examined by:
(Signature)
Name of Faculty Facilitator
(Signature)
Head of Department
ACKNOWLEDGEMENT
(16 Times New Roman, bold)
First and foremost, I wish to express my sincere thanks and gratitude to my esteemed
Mentor “Name of Industry Supervisor” who has contributed so much for successful
completion of my Industrial Training by his thoughtful reviews and valuable guidance.
Next, I would like to tender my sincere thanks to “Prof. Name of HOD” (Head
Department of Electrical Engineering) for his co-operation and encouragement.
(Signature of student)
(Name of Student)
(University Roll No.)
