Master Specifications

Important Information
1
Section 1A - Master Specifications A
Table of Contents
Master Specifications.........................................................1A-2 Cooling Specifications................................................ 1A-7
General Specifications................................................1A-2 Power Trim Specifications.......................................... 1A-7
Ignition Specifications................................................. 1A-3 Midsection Specifications........................................... 1A-7
Charging and Starting Specifications..........................1A-3 Gear Housing Specifications...................................... 1A-8
Fuel System Specifications.........................................1A-4 Gear Housing Specifications...................................... 1A-8
Cylinder Block/Crankcase Specifications................... 1A-5 Power Steering Specifications.................................... 1A-8
Cylinder Head Specifications......................................1A-6 Hydraulic Steering Specifications............................... 1A-9
Lubrication System Specifications.............................. 1A-7 Propeller Chart...................................................................1A-9

90-8M0060785 DECEMBER 2011 Page 1A-1

Master Specifications

Master Specifications
General Specifications
Model Specifications
Kilowatts (horsepower) 110 kW (150 hp)
Number of cylinders 4
Outboard weight
150 L 206 kg (454.15 lb)
150 XL/CXL 213 kg (470 lb)
Displacement 3.0 liter (183 in.³)
Cylinder bore 101.609 mm (4.0 in.)
Stroke 92.00 mm (3.62 in.)
RPM
Idle (in gear) 650 ± 50 RPM
WOT 5000–5800 RPM
Fuel system Computer controlled multi‑port electronic fuel injection
Ignition system SmartCraft engine control module (ECM) 70 digital inductive
Spark plug type NGK ZFR5F
Spark plug gap 0.8 mm (0.0314 in.)
Spark plug hex size 16 mm
Spark plug torque 27 Nm (20 lb‑ft)
Spark plug hole size 14 mm
Firing order 1‑3‑4‑2
Charging system Regulated belt driven 55 A alternator
Exhaust system Through‑the‑propeller
Cooling system Water‑cooled ‑ thermostat
Lubrication system
Integrated dry sump 6.0 liters (6.3 US qt)
Trim system
Maximum tilt range 73° (–6° to 67°)
Maximum trim range 20° (–6° to 14°)

Page 1A-2 90-8M0060785 DECEMBER 2011

 Master Specifications

Ignition Specifications
Ignition Specifications
Full throttle RPM 5000–5800
Idle RPM 650 ± 50
Ignition type Digital inductive
Spark plug type NGK ZFR5F
Spark plug gap 0.8 mm (0.032 in.)
Spark plug hex size 16 mm
Spark plug torque 27 Nm (20 lb‑ft)
Spark plug hole size 14 mm
Firing order 1‑3‑4‑2
Ignition timing at idle Approximately 2° BTDC; ECM controlled
Ignition timing at WOT ECM controlled
ECM overspeed limiter Activates at 5900 RPM

Charging and Starting Specifications

Charging and Starting Specifications
Alternator output (regulated)
Output at battery (at 1000 RPM) 23–30 A
Output at battery (at 3000 RPM) 44–51 A
Output at alternator (at 1000 RPM) 32–40 A
Output at alternator (at 3000 RPM) 54–62 A
Voltage set point 14.4 ± 0.4 V
Ignition switch "OFF" 1.0 mA or less
Regulator current draw1.
Ignition switch "ON" 350 mA or less
Starter internal drive reduction ratio 6:1
Starter draw (under load) at 25 °C (77 °F) 150–225 A
Starter draw (no load) at 25 °C (77 °F) 50–70 A
Pull in coil 30 A
Hold coil 10 A
Starter solenoid
Pull in coil resistance 0.2 ± 10%
Hold coil resistance 0.8 ± 10%
Minimum brush length 6.54 mm (0.25 in.)
Starting battery rating
1000 minimum marine cranking
Required USA and Canada (SAE) starting battery type amps (MCA), 800 cold cranking
amps (CCA, or 180 amp hour (Ah)

1. All model alternator specifications require an amperage draw of less than 1.0 mA with the ignition key in the "OFF" position and an amperage
draw of not more than 350.0 mA with key in the "ON" position.

90-8M0060785 DECEMBER 2011 Page 1A-3

Master Specifications

Fuel System Specifications

Fuel System Specifications
Automotive unleaded with a minimum pump posted octane rating of 87 (90
Type of fuel
RON)
Approximate fuel pressure at idle 280–310 kPa (40.6–45.0 psi)
Approximate fuel pressure engine not running 340–370 kPa (49.3–53.7 psi)
Fuel filtration
Fuel inlet 20 microns
High pressure 20 microns

Page 1A-4 90-8M0060785 DECEMBER 2011

 Master Specifications

Cylinder Block/Crankcase Specifications

Cylinder Block/Crankcase Specifications
Number of cylinders 4
Displacement 3.0 liter (183 in.³)
Compression ratio 9.5:1
Standard bore finished hone 101.609 mm (4.0 in.)
Stroke 92.00 mm (3.62 in.)
Flatness 0.1 mm (0.0039 in.)
Cylinder deck
Surface tolerance Smooth and free of machine marks, nick, scratches
Flatness 0.1 mm (0.0039 in.)
Crankcase deck
Surface tolerance Smooth and free of machine marks, nick, scratches
Cylinder bore maximum taper (service) 0.030 mm (0.0011 in.)
Cylinder bore maximum out of round (service) 0.050 mm (0.0019 in.)
A 60.989–60.997 mm (2.4011–2.4014 in.)
Cylinder block main bearing journal
B 60.998–61.005 mm (2.4014–2.4017 in.)
(letter)
C 61.006–61.013 mm (2.4018–2.4020 in.)

Crankshaft main bearing journal A 55.993–56.001 mm (2.2044–2.2047 in.)

(letter) B 55.985–55.993 mm (2.2041–2.2044 in.)
C 53.330–53.339 mm (2.0996–2.0999 in.)
Crankshaft connecting rod journal
D 53.321–53.329 mm (2.0992–2.0995 in.)
Crankshaft end play 0.0254–0.2794 mm (0.001–0.011 in.)
Crankshaft runout 0.05 mm (0.0019 in.)
Crankshaft main bearing oil clearance 0.052–0.086 mm (0.002–0.0033 in.)
Connecting rod piston pin bore diameter 22.016–22.026 mm (0.8667–0.8671 in.)
Journal grade "I" 56.508–56.514 mm (2.2247–2.2249 in.)
Connecting rod crankshaft pin diameter
Journal grade "0" 56.514–56.520 mm (2.2249–2.2251 in.)
Connecting rod bearing oil clearance 0.052–0.082 mm (0.002–0.0032 in.)
Piston skirt standard diameter 101.563–101.578 mm (3.9985–3.9991 in.)
Minimum 0.022 mm (0.0008 in.)
Piston to cylinder clearance
Maximum 0.046 mm (0.0018 in.)
Piston pin bore diameter 22.002–22.007 mm (0.8662–0.8664 in.)
Piston pin diameter 21.996–22.001 mm (0.8659–0.8661 in.)
First 1.520–1.545 mm (0.0598– 0.0608 in.)
Piston ring groove width Second 1.530–1.555 mm (0.0602– 0.0612 in.)
Third 3.0–3.025 mm (0.1181–0.1190 in.)
First 1.5 mm (0.059 in.)
Piston ring thickness
Second 1.5 mm (0.059 in.)
First 0.02–0.045 mm (0.0007–0.0017 in.)
Piston ring side clearance
Second 0.03–0.055 mm (0.0011–0.0021 in.)
First 0.25–0.40 mm (0.0098–0.0157 in.)
Piston ring end gap Second 0.46–0.66 mm (0.0181–0.0259 in.)
Third (lower ring only) 0.25–0.76 mm (0.0098–0.0299 in.)

90-8M0060785 DECEMBER 2011 Page 1A-5

Master Specifications

Cylinder Head Specifications

Cylinder Head Specifications
Maximum warp 0.1 mm (0.0039 in.)
Deck
Minimum datum height (combustion chamber) 7 mm (0.275 in.)
Number of valves 8
Number of valves per cylinder 2
29.000–29.021 mm
Camshaft bearing inside diameter (cylinder head)
(1.1417–1.1425 in.)
19.975 ± 0.025 mm
Cylinder head camshaft center bearing thrust face
(0.7864 ± 0.0009 in.)
28.97 ± 0.01 mm
Camshaft bearing journal
(1.1405 ± 0.0004 in.)
Intake 48.05 mm (1.892 in.)
Camshaft lobe height
Exhaust 49.1 mm (1.933 in.)

Camshaft to roller clearance Intake 0.0762 mm (0.003 in.)

(lash) Exhaust 0.254 mm (0.010 in.)
Intake 30°, 44°, 60°
Valve seat angles
Exhaust 25°, 44°, 65°
Intake 1.02 ± 0.1 mm (0.04 ± 0.0039 in.)
Valve seat width (44°)
Exhaust 1.8 ± 0.1 mm (0.07 ± 0.0039 in.)
57.08 ± 0.25 mm
Uncompressed
(2.247 ± 0.0098 in.)
350 ± 25 N (78.68 ± 5.62 lbf)
Valve spring height Compressed to 50.24 mm (1.977 in.)
spring pressure
1039 ± 45 N (233.57 ± 10.11 lbf)
Compressed to 36.78 mm (1.448 in.)
spring pressure
Intake 50.8 ± 0.13 mm (2.0 ± 0.005 in.)
Valve outside diameter
Exhaust 39.4 ± 0.13 mm (1.55 ± 0.005 in.)
Valve face angle Intake and exhaust 45°
0.38 ± 0.2 mm
Intake
(0.0149 ± 0.007 in.)
Valve margin width
1.46 ± 0.35 mm
Exhaust
(0.0574 ± 0.0137 in.)
7.966 ± 0.01 mm
Valve stem diameter Intake and exhaust
(0.313 ± 0.0003 in.)
Valve stem runout (service limit
Intake and exhaust 0.038 mm (0.0015 in.)
measured at valve face)
125.14 ± 0.30 mm
Intake
(4.9267 ± 0.0118 in.)
Valve height
126.29 ± 0.30 mm
Exhaust
(4.9720 ± 0.0118 in.)
8.001–8.021 mm
Valve guide bore inside diameter Intake and exhaust
(0.3149–0.3157 in.)
Valve stem to valve guide 0.025–0.065 mm
Intake and exhaust
clearance (0.001–0.0025 in.)
24.9 ± 0.25 mm
Valve guide height Intake and exhaust
(0.980 ± 0.0098 in.)

Page 1A-6 90-8M0060785 DECEMBER 2011

 Master Specifications

Lubrication System Specifications

Lubrication System Specifications
Engine capacity with filter replacement 6 liters (6.3 US qt)
Oil filter P/N 35‑877761K1
At idle RPM (oil cold to warm) 152–303 kPa (22–44 psi)
At WOT RPM (oil cold to warm) 372–476 kPa (54–69 psi)
Oil pressure
At idle RPM (oil hot) 76–152 kPa (11–22 psi)
At WOT RPM (oil hot) 276–373 kPa (40–54 psi)

Cooling Specifications
Cooling Specifications
Cooling system Water‑cooled ‑ thermostat control
At 650 RPM (idle) 5–30 kPa (0.7–4.4 psi)
Water pressure
At 5800 RPM (WOT) 80–300 kPa (11.6–43.5 psi)
Valve stroke (minimum) at full open temperature 7.62 mm (0.30 in.)
Thermostat Start to opening temperature 46.1–51.7 °C (115–125 °F)
Full open temperature 65.6 °C (150 °F)

Power Trim Specifications

Power Trim Specifications
Trim up relief valve ‑ tilt extended relief pressure 18,600 kPa (2700 psi) minimum
Trim down relief valve pressure 3730–6150 kPa (540–890 psi)
Power Trim and Steering Fluid or automatic transmission fluid (ATF) Type
System fluid
F, FA, Dexron II, or Dexron III

Midsection Specifications
Midsection Specifications
Recommended transom height
Long shaft 508 mm (20 in.)
XL shaft 635 mm (25 in.)
Tiller 60°
Steering pivot range
Remote 60°
Full tilt up angle 71°
Trim angle (on 12° boat transom) Negative 4° to positive 16°
Allowable transom thickness (maximum) 70 mm (2.75 in.)

90-8M0060785 DECEMBER 2011 Page 1A-7

Master Specifications

Gear Housing Specifications

Right‑Hand Gear Housing Specifications
Gear ratio 1.92:1 (13/25 teeth)
Gear housing capacity 780 ml (26.4 fl oz)
Gear lubricant type High Performance Gear Lubricant
Propeller shaft runout 0.152 mm (0.006 in.)
Propeller shaft end play 0.127–1.905 mm (0.005–0.075 in.)
Pinion height 0.635 mm (0.025 in.)
Forward gear backlash 0.457–0.610 mm (0.018–0.024 in.)
Reverse gear backlash 0.305–0.838 mm (0.012–0.033 in.)
At 650 RPM (idle) 5–30 kPa (0.7–4.4 psi)
Water pressure
At 5800 RPM (WOT) 80–300 kPa (11.6–43.5 psi)
Gear housing leak test (without gear lubricant, 15 minutes without leakage) 103.4 kPa (15 psi)

Gear Housing Specifications

Left‑Hand Gear Housing Specifications
Gear ratio 1.92:1 (13/25 teeth)
Gear housing capacity 545 ml (18.4 fl oz)
Gear lubricant type High Performance Gear Lubricant
Propeller shaft runout 0.152 mm (0.006 in.)
Propeller shaft end play 0.330–1.22 mm (0.013–0.048 in.)
Pinion height 0.635 mm (0.025 in.)
Forward gear backlash 0.483–0.610 mm (0.019–0.024 in.)
Reverse gear backlash 0.533–0.813 mm (0.021–0.032 in.)
At 650 RPM (idle) 5–30 kPa (0.7–4.4 psi)
Water pressure
At 5800 RPM (WOT) 80–300 kPa (11.6–43.5 psi)
Gear housing leak test (without gear lubricant, 15 minutes without leakage) 103.4 kPa (15 psi)

Power Steering Specifications

Power Steering Specifications
Synthetic Power Steering Fluid
Fluid type
SAE 0W‑30
Capacity Typical 1–2 liters (1–2 US qt)
Current draw Not to exceed 75 A
Steering ratio (32 cc helm and single steering cylinder, lock to lock) ‑ preferred configuration 3.8 turns
Steering ratio (40 cc helm and single steering cylinder, lock to lock) 3.0 turns
Steering ratio (50 cc helm and single steering cylinder, lock to lock) 2.4 turns
Steering ratio (32 cc helm with dual steering cylinders, lock to lock) 7.6 turns
Steering ratio (40 cc helm with dual steering cylinders, lock to lock) ‑ preferred configuration 6.0 turns
Steering ratio (50 cc helm with dual steering cylinders, lock to lock) 4.8 turns

Page 1A-8 90-8M0060785 DECEMBER 2011

 Master Specifications

Hydraulic Steering Specifications

Hydraulic Steering Specifications
Fluid type Hydraulic Helm Steering Fluid
Steering ratio (28 cc helm and single steering cylinder, lock to lock) ‑ preferred configuration 4.3 turns
Steering ratio (33 cc helm and single steering cylinder, lock to lock) 3.7 turns
Steering ratio (39 cc helm and single steering cylinder, lock to lock) 3.1 turns
Steering ratio (28 cc helm with dual steering cylinders, lock to lock) 8.6 turns
Steering ratio (33 cc helm with dual steering cylinders, lock to lock) 7.3 turns
Steering ratio (39 cc helm with dual steering cylinders, lock to lock) ‑ preferred configuration 6.2 turns

Propeller Chart
Mercury/Mariner 150 EFI FourStroke
• Wide‑open throttle RPM: 5000–5800
• Recommended transom heights: 50.8 cm (20 in.), 63.5 cm (25 in.)
• Gear ratio: 1.92:1
• Right‑hand rotation (RH), left‑hand rotation (LH)
• Aluminum (al)

Diameter No. of Approx. Gross Boat Approx. Boat Propeller Part

Pitch Model Speed Range
(inches) Blades Wgt. Length Number
Trophy Up to 952.54 kg Up to 5.79 m 93.34–109.43 km/h
13.75 26 4 48‑825944A47
Plus (2100 lb) (19 ft) (58–68 mph)
Up to 952.54 kg Up to 5.79 m 93.34–109.43 km/h
14.00 26 3 Fury 48‑8M8023160
(2100 lb) (19 ft) (58–68 mph)
Tempest Up to 952.54 kg Up to 5.79 m 93.34–109.43 km/h
14.62 26 3 48‑825874A47
Plus (2100 lb) (19 ft) (58–68 mph)
Trophy 816.46–997.9 kg 5.18–5.79 m 88.51–104.6 km/h
13.75 25 4 48‑825942A47
Plus (1800–2200 lb) (17–19 ft) (55–65 mph)
816.46–997.9 kg 5.18–5.79 m 88.51–104.6 km/h
14.00 25 3 Fury 48‑8M8023140
(1800–2200 lb) (17–19 ft) (55–65 mph)
Tempest 816.46–997.9 kg 5.18–5.79 m 88.51–104.6 km/h
14.62 25 3 48‑825866A47
Plus (1800–2200 lb) (17–19 ft) (55–65 mph)
816.46–997.9 kg 5.18–5.79 m 88.51–104.6 km/h
13.25 25 5 HighFive 48‑816374A46
(1800–2200 lb) (17–19 ft) (55–65 mph)
816.46–997.9 kg 5.18–5.79 m 88.51–104.6 km/h 48‑16550A46 (RH)
13.75 25 3 Laser II
(1800–2200 lb) (17–19 ft) (55–65 mph) 48‑16549A46 (LH)
Trophy 907.18–1088.62 kg 5.48–6.09 m 93.34–104.6 km/h
13.75 24 4 48‑825940A47
Plus (1900–2300 lb) (18–20 ft) (53–62 mph)
907.18–1088.62 kg 5.48–6.09 m 93.34–104.6 km/h
14.00 24 3 Fury 48‑8M8023120
(1900–2300 lb) (18–20 ft) (53–62 mph)
Tempest 861.85–1043.26 kg 5.48–6.09 m 93.34–104.6 km/h
14.62 24 3 48‑825872A47
Plus (1900–2300 lb) (18–20 ft) (53–62 mph)
Trophy 907.18–1088.62 kg 5.48–6.09 m 80.46–96.56 km/h
13.75 23 4 48‑825938A47
Plus (2000–2400 lb) (18–20 ft) (50–60 mph)
Tempest 907.18–1088.62 kg 5.48–6.09 m 80.46–96.56 km/h 48‑825864A47 (RH)
14.62 23 3
Plus (2000–2400 lb) (18–20 ft) (50–60 mph) 48‑825865A47 (LH)
907.18–1088.62 kg 5.48–6.09 m 80.46–96.56 km/h
13.25 23 5 HighFive 48‑815762A46
(2000–2400 lb) (18–20 ft) (50–60 mph)

90-8M0060785 DECEMBER 2011 Page 1A-9

Master Specifications

Diameter No. of Approx. Gross Boat Approx. Boat Propeller Part

Pitch Model Speed Range
(inches) Blades Wgt. Length Number
48‑825906A48
907.18–1088.62 kg 5.48–6.09 m 80.46–96.56 km/h
14.00 23 4 VenSura (RH)48‑825907A48
(2000–2400 lb) (18–20 ft) (50–60 mph)
(LH)
907.18–1088.62 kg 5.48–6.09 m 80.46–96.56 km/h 48‑16320A46 (RH)
13.5 23 3 Vengence
(2000–2400 lb) (18–20 ft) (50–60 mph) 48‑16321A46 (LH)
907.18–1088.62 kg 5.48–6.09 m 80.46–96.56 km/h 18‑16548A46 (RH)
13.75 23 3 Lazer II
(2000–2400 lb) (18–20 ft) (50–60 mph) 48‑16547A46 (LH)
Black Max 907.18–1088.62 kg 5.48–6.09 m 80.46–96.56 km/h
14.00 23 3 48‑832834A45
(al) (2000–2400 lb) (18–20 ft) (50–60 mph)
Tempest 952.54–1179.34 kg 5.48–6.4 m 75.64–91.73 km/h
14.62 22 3 48‑8M8026820
Plus (2100–2600 lb) (18–21 ft) (47–57 mph)
952.54‑1179.34 kg 5.48–6.4 m 75.64–91.73 km/h
13.50 22 3 Enertia 48‑899202A46
(2100–2600) (18–21 ft) (47–57 mph)
Trophy 997.9–1270.05 kg 5.48–6.4 m 70.81–86.9 km/h
13.75 21 4 48‑825934A47
Plus (2200–2800 lb) (18–21 ft) (44–54 mph)
48‑825862A47
Tempest 997.9–1270.05 kg 5.48–6.4 m 70.81–86.9 km/h
14.62 21 3 (RH)48‑825863A47
Plus (2200–2800 lb) (18–21 ft) (44–54 mph)
(LH)
48‑899002A46
997.9–1270.05 kg 5.48–6.4 m 70.81–86.9 km/h
13.62 21 3 Enertia (RH)48‑899003A46
(2200–2800 lb) (18–21 ft) (44–54 mph)
(LH)
Mirage 997.9–1270.05 kg 5.48–6.4 m 70.81–86.9 km/h 48‑13702A46 (RH)
14.75 21 3
Plus (2200–2800 lb) (18–21 ft) (44–54 mph) 48‑13703A46 (LH)
997.9–1270.05 kg 5.48–6.4 m 70.81–86.9 km/h
13.25 21 5 HighFive 48‑815760A46
(2200–2800 lb) (18–21 ft) (44–54 mph)
997.9–1270.05 kg 5.48–6.4 m 70.81–86.9 km/h 48‑825902A48 (RH)
14.00 21 4 VenSura
(2200–2800 lb) (18–21 ft) (44–54 mph) 48‑825903A48 (LH)
997.9–1270.05 kg 5.48–6.4 m 70.81–86.9 km/h 48‑16318A46 (RH)
13.75 21 3 Vengence
(2200–2800 lb) (18–21 ft) (44–54 mph) 48‑16319A46 (LH)
Black Max 997.9–1270.05 kg 5.48–6.4 m 70.81–86.9 km/h
14.25 21 3 48‑832832A45
(al) (2200–2800 lb) (18–21 ft) (44–54 mph)
1043.26–1179.34 kg 5.79–6.7 m 67.59–83.68 km/h
13.75 20 3 Enertia 48‑899000A46
(2300–3000 lb) (19–22 ft) (42–52 mph)
1043.26–1179.34 kg 5.79–6.7 m 67.59–83.68 km/h 48‑834854A45 (RH)
14.00 20 4 Alpha 4 (al)
(2300–3000 lb) (19–22 ft) (42–52 mph) 48‑834855A45 (LH)
Tempest 1133.98–1451.50 kg 5.79–6.7 m 62.76–78.85 km/h 48‑825860A47 (RH)
14.62 19 3
Plus (2500–3200 lb) (19–22 ft) (39–49 mph) 48‑825861A47 (LH)
1133.98–1451.50 kg 5.79–6.7 m 62.76–78.85 km/h 48‑898998A46 (RH)
14.00 19 3 Enertia
(2500–3200 lb) (19–22 ft) (39–49 mph) 48‑898999A46 (LH)
Mirage 1133.98–1451.50 kg 5.79–6.7 m 62.76–78.85 km/h 48‑13700A46 (RH)
15.25 19 3
Plus (2500–3200 lb) (19–22 ft) (39–49 mph) 48‑13701A46 (LH)
1133.98–1451.50 kg 5.79–6.7 m 62.76–78.85 km/h
13.25 19 5 HighFive 48‑815758A46
(2500–3200 lb) (19–22 ft) (39–49 mph)
1133.98–1451.50 kg 5.79–6.7 m 62.76–78.85 km/h 48‑825900A48 (RH)
14.00 19 4 VenSura
(2500–3200 lb) (19–22 ft) (39–49 mph) 48‑825901A48 (LH)
1133.98–1451.50 kg 5.79–6.7 m 62.76–78.85 km/h 48‑16316A46 (RH)
14.00 19 3 Vengence
(2500–3200 lb) (19–22 ft) (39–49 mph) 48‑16317A46 (LH)
Black Max 1088.62–1270.05 kg 5.79–6.7 m 62.76–78.85 km/h
14.50 19 3 48‑832830A45
(al) (2500–3200 lb) (19–22 ft) (39–49 mph)

Page 1A-10 90-8M0060785 DECEMBER 2011

 Master Specifications

Diameter No. of Approx. Gross Boat Approx. Boat Propeller Part

Pitch Model Speed Range
(inches) Blades Wgt. Length Number
1224.69–1632.93 kg 5.79–7.01 m 56.32–74.02 km/h
14.25 18 3 Enertia 48‑898996A46
(2700–3600 lb) (19–23 ft) (35–46 mph)
Mirage 1224.69–1632.93 kg 5.79–7.01 m 56.32–74.02 km/h 48‑889620A46 (RH)
15.38 18 3
Plus (2700–3600 lb) (19–23 ft) (35–46 mph) 48‑889619A46 (LH)
1224.69–1632.93 kg 5.79–7.01 m 56.32–74.02 km/h 48‑834852A45 (RH)
14.50 18 4 Alpha 4 (al)
(2700–3600 lb) (19–23 ft) (35–46 mph) 48‑834853A45 (LH)
Mirage 1315.41–1814.36 kg 5.79–7.01 m 51.49–62.9 km/h 48‑18278A46 (RH)
15.50 17 3
Plus (2900–4000 lb) (19–23 ft) (32–43 mph) 48‑90159A46 (LH)
Tempest 1315.41–1814.36 kg 5.79–7.01 m 51.49–69.2 km/h
14.62 17 3 48‑8M8026790
Plus (2900–4000 lb) (19–23 ft) (32–43 mph)
1315.41–1814.36 kg 5.79–7.01 m 51.49–69.2 km/h 48‑898994A46 (RH)
14.50 17 3 Enertia
(2900–4000 lb) (19–23 ft) (32–43 mph) 48‑898995A46 (LH)
1315.41–1814.36 kg 5.79–7.01 m 51.49–69.2 km/h
13.50 17 5 HighFive 48‑821154A46
(2900–4000 lb) (19–23 ft) (32–43 mph)
1315.41–1814.36 kg 5.79–7.01 m 51.49–69.2 km/h 48‑825898A48 (RH)
14.25 17 4 VenSura
(2900–4000 lb) (19–23 ft) (32–43 mph) 48‑825899A48 (LH)
1315.41–1814.36 kg 5.79–7.01 m 51.49–69.2 km/h 48‑16314A46 (RH)
14.50 17 3 Vengence
(2900–4000 lb) (19–23 ft) (32–43 mph) 48‑16315A46 (LH)
Black Max 1315.41–1814.36 kg 5.79–7.01 m 51.49–69.2 km/h
15.00 17 3 48‑832828A45
(al) (2900–4000 lb) (19–23 ft) (32–43 mph)
1406.13–1723.65 kg 6.09–7.31 m 46.67–64.37 km/h
14.75 16 3 Enertia 48‑898992A46
(3100–4500 lb) (20–24 ft) (29–40 mph)
1406.13–1723.65 kg 6.09–7.31 m 46.67–64.37 km/h 48‑834850A45 (RH)
15.00 16 4 Alpha 4 (al)
(3100–4500 lb) (20–24 ft) (29–40 mph) 48‑834851A45 (LH)
1542.2–23133.3 kg 6.4–7.62 m 41.84–59.54 km/h 48‑898990A46 (RH)
15.00 15 3 Enertia
(3400–5100 lb) (21–25 ft) (26–37 mph) 48‑898991A46 (LH)
Mirage 1542.2–23133.3 kg 6.4–7.62 m 41.84–59.54 km/h 48‑19838A46 (RH)
15.75 15 3
Plus (3400–5100 lb) (21–25 ft) (26–37 mph) 48‑19841A46 (LH)
Revolution 1542.2–2313.3 kg 6.4–7.62 m 41.84–59.54 km/h
14.62 15 4 48‑857022A46
4 (3400–5100 lb) (21–25 ft) (26–37 mph)
Black Max 1542.2–2313.3 kg 6.4–7.62 m 41.84–59.54 km/h
15.25 15 3 48‑78116A45
(al) (3400–5100 lb) (21–25 ft) (26–37 mph)
1542.2–2313.3 kg 6.4–7.62 m 41.84–59.54 km/h
15.13 14 3 Enertia 48‑898988A46
(3400–5100 lb) (21–25 ft) (26–37 mph)
Mirage 1905.08–2540.17 kg 6.7–8.53 m 30.57–49.88 km/h
16 13 3 48‑826072A46
Plus (4200–7300 lb) (22–28 ft) (19–31 mph)
Black Max 1905.08–2540.17 kg 6.7–8.53 m 30.57–49.88 km/h
16 13 3 48‑78114A45
(al) (4200–7300 lb) (22–28 ft) (19–31 mph)
Black Max 2721.55+ kg Pontoon/ 19.31–40.23 km/h
16 12 3 48‑16436A45
(al) (6000+ lb) Work (12–25 mph)
Black Max 3175.14+ kg 1.6–37.0` km/h 48‑78112A45 (RH)
16 11 3 Work
(al) (8000+ lb) (1–23 mph) 48‑78117A40 (LH)

90-8M0060785 DECEMBER 2011 Page 1A-11

Master Specifications

Notes:

Page 1A-12 90-8M0060785 DECEMBER 2011