M/s.

INDIAN INSTITUTE OF MANAGEMENT, BANGALORE

ABSTRACT ESTIMATE FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

COMPANY NAME :
Sl No Description Amount
Rs

CIVIL,WATER SUPPLY AND PLUMBING, LIFT, ELECTRICAL AND EXHAUST VENTILATION WORKS

1 CIVIL WORKS 0.00

2 WATER SUPPLY WORKS, PLUMBING WORKS AND RE-ROUTING OF EXISTING LINES 0.00

3 SUPPLY AND INSTALLATION OF LIFT 0.00

4 ELECTRICAL WORKS 0.00

5 EXHAUST VENTILATION SYSTEM 0.00

GRAND TOTAL 0.00

GST, EXTRA AS APPLICABLE

 M/s. INDIAN INSTITUTE OF MANAGEMENT, BANGALORE
ABSTRACT ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT
CANTEEN
Sl No Description Amount
Rs.

A EARTH WORK EXCAVATION 0.00

B ANTI-TERMITE TREATMENT 0.00

C PLAIN CEMENT CONCRETE WORKS 0.00

D REINFORCED CEMENT CONCRETE WORKS 0.00

E FORMWORK 0.00

F REINFORCEMENT STEEL 0.00

G STRUCTURAL STEEL 0.00

H MASONRY WORKS 0.00

I PLASTERING WORKS 0.00

J PAINTING WORKS 0.00

K FLOORING WORKS 0.00

L RAILING WORKS 0.00

M ALUMINIUM GLAZING WORKS 0.00

N GENERAL PURPOSE METAL DOOR 0.00

O LAMINATED PARTITIONS FOR TOILET 0.00

P WOODEN DOORS 0.00

Q SHERA BOARD FOR DUCT COVERING 0.00

R FALSE CEILING WORKS 0.00

S WATERPROOFING WORKS 0.00

T DISMANTLING WORKS 0.00

U MISCELLENOUS WORKS 0.00

TOTAL FOR CIVIL WORKS 0.00

GST, EXTRA AS APPLICABLE
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

A EARTH WORK EXCAVATION

Earthwork excavation over areas to depths upto 1.50 meters in Ordinary soil in general
development work and lowering of level and transporting and dumping earth manually
or by using mechanical equipment’s, filling in areas as directed by the Engineer-in-
charge anywhere within the premises in layers not exceeding 20 cms each, breaking
1 Cum 35.00 0.00
clods with discs, harrows or other effective means, compacting thoroughly with power
road rollers, etc. and dressing to the required formation with all leads and lifts
(Payments will be made only on the volume of the earth excavated, computed with
levels taken before and after excavation in the area) complete as directed.

Earthwork Excavation in Foundations, Trenches, in Ordinary Soil upto a Depth not

exceeding 1.50 Mtrs, including dressing the bottom and sides of pit and trenches,
2 Cum 550.00 0.00
stacking the excavated soil clear from edges of excavation with lead upto 50 M as
directed by the Engineer-in-charge, etc., complete

Earthwork Excavation in Foundations, Trenches, in Ordinary Soil, Depth from 1.50 to

3.0 Mtrs, including dressing the bottom and sides of pit and trenches, stacking the
3 Cum 325.00 0.00
excavated soil clear from edges of excavation with lead upto 50 M as directed by the
Engineer-in-charge, etc., complete

Earthwork Excavation in Foundations, Trenches, in Hard soil upto a Depth not

exceeding 1.50 Mtrs, including dressing the bottom and sides of pit and trenches,
4 Cum 100.00 0.00
stacking the excavated soil clear from edges of excavation with lead upto 50 M as
directed by the Engineer-in-charge, etc., complete.

Earthwork Excavation in Foundations, Trenches, in Hard Soil, Depth from 1.50 to 3.0
Mtrs, including dressing the bottom and sides of pit and trenches, stacking the
5 Cum 125.00 0.00
excavated soil clear from edges of excavation with lead upto 50 M as directed by the
Engineer-in-charge, etc., complete

Excavation in foundations, trenches in Soft rock/Ordinary Rock for Depth not

Exceeding 1.5 mtrs without blasting method like chisseling, quenching etc. including
6 Cum 50.00 0.00
stacking in rectangular / Trapizoidial shape for measurement at ground level as
directed by the Engineer-in-charge etc complete.

Earthwork excavation for foundation in Soft rock/Ordinary rock for Depth from 1.50 to
3.0 Mtrs without blasting method like chisseling, quenching etc.including stacking in
7 Cum 50.00 0.00
rectangular / trapizodial shape for measurement at ground level as directed by the
Engineer-in-charge etc. complete.

Earthwork Excavation for foundations, trenches in hardrock removed by cutting,

chiseling, wedging where blasting is prohibited, upto a depth not exceeding 1.50 mtrs,
8 including stacking the excavated stuff clear from edges of excavation with lead upto Cum 50.00 0.00
50m. Payment will be based on stack measurement after allowing for voids as specified
in the technical specifications.

Earthwork Excavation for foundations, trenches in hardrock removed by cutting,

chiseling, wedging where blasting is prohibited, from 1.50m to 3.0m in depth including
9 stacking the excavated stuff clear from edges of excavation with lead upto 50m. Cum 50.00 0.00
Payment will be based on stack measurement after allowing for voids as specified in
the technical specifications.

Filling available excavated earth (excluding rock) in sides of foundations upto plinth in
layers not exceeding 20cms in depth, compacting each deposited layer by ramming
10 Cum 600.00 0.00
after watering with lead upto 50m and lift upto 1.5m including cost of all labour
complete as per specifications.
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Shifting of surplus excavated earth, which includes earth excavated from foundations
and general excavation and conveying within the campus premises as directed by
11 Cum 275.00 0.00
Engineer-in-charge. Measurement will be on the nett quantities after deducting for
voids.(Truck/trailer measurement less 25% voids).

TOTAL FOR EARTHWORK EXCAVATION 0.00

B ANTI-TERMITE TREATMENT
Providing and injecting chemical emulsion for Preconstructional Anti-Termite
Treatment, creating continuous chemical barrier under and around the column pits,
walls, trenches, basement excavation, top surface of the plinth filling, junction of wall
and floor, along the external perimeter of building, expansion joints, over the top
surface of consolidated earth on which apron is to be laid, surrounding of pipes and
conduits, with chloropyriphos emulsifiable concentrates of 20% concentration at 3.19
12 Litre/Sqm, including cost of chemical, diluting in water to one per cent concentration, Sqm 755.00 0.00
including cost of all materials, labour, HOM of machinery, with all leads and lifts,
loading and unloading charges, transportation cost and conveyance and all other
incidental charges etc complete for successful completion of work as per specifications
and as directed by Engineering in charge. (Plinth area of the building at ground floor
only shall be measured)The contractor to furnish necessary certificate for 10 year
warranty.
TOTAL FOR ANT-TERMITE TREATMENT 0.00
C PLAIN CEMENT CONCRETE WORKS
Providing and placing Plain Cement Concrete M10/1:4:8 - 100mm thick for Foundation
of Walls, Below Footings and Below Plinth Beams with coarse graded aggregates of
13 Cum 41.00 0.00
20mm and down size, laid in layers and compacted by wooden or cast iron rammers
including necessary shuttering, finishing, curing etc complete.

Providing and placing Plain Cement Concrete M10/1:4:8 - 100mm thick , Below Floors,
Pavements, Steps, etc;, using coarse graded aggregates of 20 mm and down size, laid
14 Cum 90.00 0.00
in layers and compacted by wooden or cast iron rammers including necessary
shuttering , finishing, curing etc complete.

Providing and laying plain cement concrete M10 (1:3:6) for damp proof course
75 mm thick and above in below floor, foundation and plinth level etc. using coarse
15 graded aggregates 20 mm and down size and admixture of approved water proofing Cum 5.00 0.00
compound 2% by weight of cement and compacted by wooden or cast iron rammers,
including necessary shuttering etc. complete.
TOTAL FOR PLAIN CEMENT CONCRETE WORKS 0.00
D REINFORCED CEMENT CONCRETE WORKS
Important notes in regard to reinforced cement concrete.
1. All concrete used for reinforced concrete work (structural concrete) shall be
"Controlled concrete"
While quoting for structural concrete work contractors are particularly advised to study
the relevant drawings carefully before quoting.
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Providing & laying controlled reinforced cement concrete confirming to grades as

specified in (IS 456 - 2000) as per specifications using 20mm down size aggregates at
any depth or heights excluding the cost of steel reinforcement centring, shuttering,
scaffolding but inclusive of cost towards compacting with vibrations, curing and hacking
the exposed surfaces wherever required to receive plaster or floated steel troweled
surface whenever specified. The rate shall include cover blocks in concrete to keep
reinforcement in position made of PVC or Nylon of approved make / quality and
arrangements to provide recesses to slabs, columns, walls and placing and securing
properly within the formwork sleeves and / or opening in slabs, embedments such as
insert plates, bolts, corner protection angles, anchors etc. (embedment shall be paid
seperately under respective items), construction joints, sunk slabs, cantilever slabs,
making holes or cutting formwork for taking out Electrical conduits or dowels for column
to Block / Brick work etc. to the required shape, size and slope as shown in the
drawing.
The rates shall also include account for any admixtures (approved by the consultants)
the contractor may use in order to enhance the workability, durability to achieve
accelerated strength if required etc. The rate shall include use of plasticizers and
retarders to limit the water/cement ratio to 0.45 and the temperature to 25 degree C at
the time of setting. Complete care shall be taken to achieve dense and fully watertight
concrete. All requirements to pump the concrete to the required places with good
rheology shall be considered while quoating.
A qualified machanic shall always be available during working hours for maintenance of
weight batching machines.
The sucessful tenderer shall maintain at site, cube testing machine in good working
order, sieves, slump cone, graduated cylinder and weights, scales for material testing
and other relevent lab equipments as per technical specifications.
Note: Construction joints shall be at pre approved locations only and shall be vertical or
stepped. Concrete shall be chipped immediately after final setting using mechanical
chippers and thorougly cleaned surface shall be given
a. A thick coat of slurry if the joint is less than 3 days old
b. A thick coat of slurry with latex based admixture if the joint is less than 7 days old
c. A coat of epoxy if it is more than 7 days
Construction joints in columns, walls shall be horizontal and all the latent concrete shall
be removed after final setting and shall be given a coat of thick slurry if the joint is
below the floor level and mortor poured from the top mix proportion equal to that of
concrete. Adequate care including necessary formwork shall be taken to cast rich mix
around columns if difference in strength specified is 25%

The starter concrete should be thoroughly compacted and shall be green construction
joint. The minimum height of the strater should be atleast 300mm
Contractor shall submit a scheme and get it approved for all locations of construction
joints envisaged.
For all structural concrete elements post construction dimension and levels
shall be documented, submitted and shall insisted upon.
Controlled Contrete of Grade M-25- Cement content-340kg/cum
Controlled Contrete of Grade M-30- Cement content-360kg/cum

Providing and laying Reinforced Cement Concrete M 25 (Controlled Concrete) for

Footings, rafts, strips & beams in foundations of all shapes and sizes, using 20 mm and
16 Cum 110.00 0.00
downsize graded aggregates, at all depths, complete as per specification, excluding
cost of shuttering.

Providing and laying Reinforced Cement Concrete M 30 (controlled concrete) for

Pedestal,Columns, Column Brackets, Shear walls of all shapes and sizes, at all levels
17 Cum 160.00 0.00
and heights, using 20 mm and downsize graded aggre-gates, complete as per
specification, excluding cost of shuttering.
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Providing and laying Reinforced Cement Concrete M 25 (controlled concrete) for UG

Sump walls of all shapes and sizes, at all levels and heights, using 20 mm and
18 Cum 20.00 0.00
downsize graded aggre-gates, complete as per specification, excluding cost of
shuttering.

Providing and laying Reinforced Cement Concrete M 30 (Controlled Concrete) for Plinth
19 Beams of all shapes and sizes, at all levels and heights, using 20 mm and downsize Cum 35.00 0.00
graded aggregates complete as per specification, excluding cost of shuttering.

Providing and laying Reinforced Cement Concrete M 25 (Controlled Concrete) for UG

Sump Slabs, including capitals and sloping slabs, at all levels & heights, for floors,
20 Cum 6.00 0.00
roofs, canopies, balconies, staircase landings, etc; using 20mm & down size graded
aggregates, complete as per specification, excluding cost of shuttering.

Providing and laying Reinforced Cement Concrete M 30 (Controlled Concrete) for all
types of Slabs, Flat Slabs including capitals and sloping slabs, at all levels & heights,
21 Cum 255.00 0.00
for floors, roofs, canopies, balconies, staircase landings, etc; using 20mm & down size
graded aggregates, complete as per specification, excluding cost of shuttering.

Providing and laying Reinforced Cement Concrete M 30 (Controlled Concrete) for

Lintels & Beams, Ledges of all shapes and sizes, at all levels and heights, using 20 mm
22 Cum 100.00 0.00
and downsize graded aggregates complete as per specification, excluding cost of
shuttering.

Providing and laying Reinforced Cement Concrete M 25 (Controlled Concrete) for all
types of Staircase with waist slab, stringer beams and steps, complete as shown in the
23 Cum 15.00 0.00
drawings, at all levels and heights, using 20 mm and downsize graded aggregates,
complete as per specification, excluding cost of shuttering.

Providing precast M30 RCC coping of top width 400 mm and 50 mm high including
24 providing drip mould, fixing in position in CM 1:4, etc complete as per drawing. If the Rmt 215.00 0.00
sectional area is changed, rate will be revised proportionately.

Providing precast M30 RCC coping of top width 250 mm and 40 mm high including
25 providing drip mould, fixing in position in CM 1:4, etc complete as per drawing. If the Rmt 10.00 0.00
sectional area is changed, rate will be revised proportionately. (M.R)

Providing 75 mm thick RCC precast slab with cement concrete M25 grade using coarse
graded aggregate 12.5 mm and down size. The work includes necessary casting
26 platform, shuttering, finishing smooth with cement mortar 1:4, on exposed faces, Sqm 250.00 0.00
curing, transporting to work site, hoisting and fixing in position and finishing complete
including cost of reinforcement steel. (D.R)
TOTAL FOR REINFORCED CEMENT CONCRETE WORKS 0.00
E FORMWORK FOR CONCRETE WORKS:
The Heights of each floor is 3.45m from FFL.-(Gr + F floor).
General Notes: Unless otherwise specified, rates quoted for all items shall include the
following 1) Providing, fabricating and erecting form work at all levels and places
wherever needed/specified to gentle slope, roof projections at various levels and
profiled formwork as per drawing including striking with 12mm thick Plastic coated
marine resistant waterproof ply / smooth finished MS shuttering plates with adjustable
steel props of acceptable staging system and with sufficient bracing as approved by
Engineer. 2) Cost to include designing of proper form work and staging system and all
its components to suit the requirements, submission of design calculations and shop
drawings for approval, sealing the joints with heavy duty self adhesive tape and same
shall be removed, aligning to line and levels including M.S. Ties, rods, PVC sleeves,
providing openings/ cutouts/ pockets, applying deshuttering agent , all lift and Leads
etc, complete at all levels and profiles as per detailed drawings.
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

3) Providing, fabricating and erecting form work at all levels and locations, laying to
gentle slope, special staging for casting floors up to 4.5m height. 4) Contractors shall
submit drawings showing the scheme of formwork including back proping and proper
sequence of removal of formwork and back propping so that the structural slab will not
be overloaded due to construction loads. 5) All slabs shall be progressively deshuttered
and backpropped as per the approval of the Engineer. It is compulsory to provide
adequate back props to the slab on which the supports are resting before taking up
concreting work for every slab.

6) Formwork shall be designed for close jointed rigid, durable and shall have adequate
strength, water tightness and ensure easy removal etc.7) Props, shorings and bracings
shall be all in steel. Formwork designed with proposed materials (to be approved prior
to making) shall be able to retain its shape, line, dimension, level within the allowable
limits of tolerance as approved by the Engineer. 8) Necessary arrangement shall be
envisaged to provide camber in beams or slabs as per design.

9) Formwork for construction joints shall be submitted to the Engineer for approval.
Shuttering below the shrinkage strip at every level shall be retained in place without
disturbing for a time as specified in the drawings. 10) Any defective concrete shall not
be acceptable,honeycombing,Any undulations, bulging etc shall be chipped and
finished by the contractor without any extra cost. 11) Formwork shall facilitate for
making holes / recess for leaving dowells embedments etc. at no additional cost and
shall be submitted to the Engineer for approval. 12) The rates quoted shall include for
structural elements of all types, shapes, sizes and profiles at all levels.
IMPORTANT NOTE TO BE CONSIDERED AT THE TIME OF QUOATING:-
FORMWORK FOR ALL AREAS AT ALL LEVELS AND HEIGHTS FOR RCC
WALLS,COLUMNS,COLUMN CAPITALS,DROP PANELS, DROP BEAMS,
SLABS,TRANSFER GIRDERS, SHEAR WALL, RCC WALLS ETC THE MATERIAL
FOR SHUTTERING SHALL BE OF APPROVED GOOD QUALITY MARINE
PLYWOOD ONLY SHALL BE USED. ( ALL THESE AREAS ARE UN-PLASTERED
SURFACES)
Note: All Necessary Centering, Shuttering, Stagging, Scaffolding, Acrospans,
Purlins, Cuplock, Adjustable Short & Long Props etc Shall be of Steel Members
only. No Casurina poles or any other wooden supporting members are allowed
to be used in the project.
Contractors shall submit drawings showing the scheme of formwork including
back proping and proper sequence of removal of formwork and back propping
so that the structural slab will not be overloaded due to construction loads at
any levels.
Contractor shall submit scheme and methodolgy including load calculations,
design of formwork, staging, proping, to retain its shape, line, dimension, level,
bracings for rigidity, side supports to avoid bulging and it shall have some
redendency.
Formwork in following items of work at all levels. The floor heights for each floor
is 3.45m from FFL.
27 For Footings, Rafts sqm 200.00 0.00
28 For Plinth Beams sqm 290.00 0.00
29 For Pedestals, Columns, Walls & Shear walls sqm 1625.00 0.00
30 For Floor beams sqm 505.00 0.00

For Slabs inculding, sunken slabs, cantilever slabs, slab projections, balcony slabs,
31
Duct covering slabs etc. of different shapes / profile at different levels.

a) At First Floor Level sqm 550.00 0.00

b) At Terrace Floor Level sqm 760.00 0.00

32 Staircases - Treads, Risers, Waist Slabs, Midlanding sqm 90.00 0.00

 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

FORM FACED FORMWORK

Providing, fabricating and erecting form faced formwork upto 4.50 mtrs floor height at
all levels and places wherever needed / specified as per drawing including striking /
deshuttering with necessary saftey precautions.
Material :12mm thick Marine grade or film faced plywood of high density (34 Kg)
of make Green Ply/Virgo/Archid Ply should be used and shall be repeated upto a
maximum of 10 repetations. (5 repetations on each side) with surface treatments that
provide a nearly impervious and smooth surface. Mixing different brands or surface
treatments should be avoided to avert variations in colour caused by amount of water
absorption.
Shuttering Oil for all Slabs, Beams, Shear walls, Columns, Chajjas etc shall be of
Rebbol -E from M/s. Fosroc, Sika Form Oil from M/s. Sika & Dr. Fixit De-shuttering Oil
from M/s. Dr.Fixit
Form Liners: Form Liners in concrete works upto 250mm in height for elevation with
white band shall be of foam liner made out of fiber glass fixed to the form work.
Texture finish of fiber glass shall be as per architects requirement.
Accuracy : Form faced formwork should be designed, constructed and maintained in
accordence with detailed specifications, recommendations of ACI 347-04 and additional
requiremnts out lined. Form faced concrete requires care in design to minimize
deflection, deformations, pillowing, offsets and mortor leakage. Specified clearances
between reinforcement and formwork should be maintained.
Form face should be designed as a stable envelop to contain the fresh concrete, extra
walers, additional ties and bracings to be provided to stisfy the deflection rrequirements
and also to maintain alignment during vibrating of concrete.
Form joints: Leakage should be minimized for uniform colur and texture are critical.
Leakage shall be minimized by providing lining forms with separate materials and
staggering the joints using pressure sensitive compressible gaskets / tapes or sealant
with in form interfacing joints. Care should be taken to prevent displacement of tape /
gaskets during concrete operations. A mock up panel to be done to verify the
effectiveness of taped joints.
Form Release agents : Material applied to the form sheathing to prevent the bonding
of concrete to the sheathing, to keep the formwork clean and assist in the successfull
production of high quality architectural surfaces.
For Uniformity of appearance, the same release agent should be used for all
architectural concrete surfaces.
Chemically active release agents shall be used. Fatty acids chemically react with basic
materials in concrete and produce soap. Soap is better lubricant than oil for removal of
entrapped air in fresh concrete.

Extra rate for providing form finished exposed concrete using 12mm thick marine
plywood or Equivalent Plywood shuttering to the Required Pattern NOTE:- The areas
33 for the shuttering works to be executed for exposed concrete shall be clearely sqm 2750.00 0.00
identified / defined by the Architects for which those areas only will be executed by the
contractor and only those areas shall be measured and paid. (M.R)

TOTAL FOR FORMWORKS 0.00

F REINFORCING STEEL
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Providing and fixing steel reinforcement for RCC including material,fabricating as per
IS-2502, transporting,storing, de-coiling, straightening, cutting, bending, spirally
hooping and placing in position at all levels,including all labour,
equipments,supplies,incidentals, sampling and testing as prescribed in IS codes
including all charges thereon for requisite tests,supervision and binding with approved
quality binding wire double fold to tie the bars in position. The measurement shall be as
34
per IS 1200 Part- and unit weight shall be derived as mentioned in IS 1786. The rolling
margin shall be on Contractors own cost. NOTE:- The rate shall include all
laps,Wastages,chairs,Spacers rods,pins etc as required and as directed, cost of
cover blocks,18 gauge G.I. Binding wire, to be provided as per specifications
and the same will not be measured separately for payment. Quantity of steel as
per drawing and with authorized overlaps only shall be measured and paid for.

The quoted rate will include welding of reinforcement with low hydrogen low heat
welding electrodes for the welding length mentioned in the drawings in place of
conventional laps, wherever consultants recommend, for which no extra shall be
claimed. Replacing conventional laps with welding splices will be entirely at consultant’s
discretion. Such unclaimed welding will also include welding of reinforcement to already
fixed insert plates, structural steel members etc. Shear connectors prepared from the
reinforcing steel welded to structural steel members shall be measured in the
reinforcement item.
The rate also includes protecting the reinforcing bars – in their virgin form or in the
fabricated form, or when placed and tied up position or as dowels left for future
continuation of work or at construction joint – against corrosion due to exposure to
weather if left exposed and un-encased for more than three weeks from the date of
delivery to the site. Cement wash shall be given to such bars if they are likely to be
exposed for more that three weeks and less than twelve weeks. Process of applicatin
of cement slurry shall be repeated after every twelve weeks if the exposure period is
strecthed.

TMT Bars conforming to IS:1786 with Fe = 500/500d/500s N/sq.mm (SAIL, VIZAG,

M.T 65.00 0.00
JSW, INDUS, TATA) (MR)
TOTAL FOR REINFORCEMENT STEEL 0.00
G STRUCTURAL STEEL

Preparing shop drawings, obtaining Structural consultants approval, supplying,

fabricating in accordance with IS:800, delivering at site, hoisting and fixing in position,
including all temporary staging and supporting work and making all structural steel work
in accordance with the design, drawings prepared by the consultants. The rate of steel
work shall include cutting, grinding, machining, assembly, welding, jointing, building up
new sections, cost of fasteners (nuts, bolts and washers), pre-heating the sections to
temperatures up to 250 degree C if thickness of the section is equal to or more than 25
mm.Fabrication will involve connections using plates, channels and angles, gusset
plate, foundation bolts, cleats, fasteners etc. as per drawing, steel conforming to IS :
226 and IS : 2062 with minimum yield strength of 350 Mpa and upto 355 Mpa. The rate
shall also include 2 coats of Synthetic Enamel Paint of Approved Make & Colour over a
coat of zinc rich primer after properly cleaning the steel surface with wire brush and
mild acid solution followed by washing with water and drying the surface completely.
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

For Supplying, fabricating, conveying, hoisting, erecting in position structural steel

works comprising of trusses, purlins, lattice girders, portal frames, brackets,
columns, bracings, base plates, gussets & other connected steel work with MS
rolled steel sections/built up sections, welded, bolted and/or riveted, anchors, bolts,
inserts in RCC / Masonary and other works etc, complete, as shown in detailed
35 M.T 6.50 0.00
approved shop drawings including straightening, cutting, welding, hoisting with sand
blasting, spray galvanising & painting zinc rich primer one before & one after erection
with 2 coats of synthetic enamel paint of appvd brand & color after erection. Only
standard weights as per IS code shall be considered for measurement and payment.
For Skylight, Grating works as specified in the Detailed drgs.

TOTAL FOR STRUCTURAL STEEL WORKS 0.00

H MASONRY WORKS

Providing and construction Solid Cement Concrete Block masonry in cement mortar 1:6
(ce- ment : coarse M- sand) using factory made, load bearing, approved quality, Grade
C (4.0), as per IS 2185 (Part 1), density of blocks not less than 1800kg/cum, minimum
average compressive strength of units 4.0N/mm² and minimum strength of individual
36 Cum 5.00 0.00
unit is 3.2N/mm², set to level plumb including setting in position, providing scaffolding,
curing, raking out joints wherever necessary etc., complete with all leads and all as per
specification and direction of engineer-in -charge For Construction of Steps and as
directed by architects.

Providing and constructing 200mm thick Walls with Solid Cement Concrete Blocks
conforming to IS 2185 with a mini-mum crushing strength of 35 Kgs/sqcm in cement
37 Sqm 580.00 0.00
mortar 1:4, in superstructure at all levels and heights including all neccessary Staging
and Scaffolding complete as per specifications. (Size of the Block is 400x200x200mm)

Providing and constructing 100 mm thick Walls with Solid Cement Concrete Blocks
conforming to IS 2185 with a mini-mum crushing strength of 35 Kgs/sqcm in cement
mortar 1:4, in superstructure at all levels and heights complete as per specifications.
38 Sqm 50.00 0.00
The quoted rate to include providing Reinforced Cement Concrete as bands 75mm th,
at every1.0- 1.2 mtrs intervals with nominal reinforcement of 2 nos 8mm dia
reinforcement bars. (Size of Block is 400x200x100mm)

Providing and constructing granite / trap/basalt size stone masonry in FOUNDATION

with cement mortar 1:6, edges of stones hammer dressed in courses not less than 20
cms high, bond stones at 2m apart in each course including the cost of all
39 materials,labour, curing, HOM of equipments and machineries, with all leads and lifts Cum 50.00 0.00
loading and unloading charges, transporation cost and conveyance all other incidental
charges etc complete for successful completion of work as per specifications and as
directed by the Engineer-in-charge.

Providing Granite Stone Cladding with stones in course of uniform height of 180mm
high 150 thk flat chisel dressed all round in CM 1:4. All stones should be of uniform
colour and thickness. All quoin stones 2 line dressed for 50 mm wide at corners.
40 Sqm 565.00 0.00
Mortar joint not to exceed 12 mm thick including amm materials dressing, labour
scaffolding including providing 10mm dia TMT bar anchors inserted 100mm into the rcc
walls at every 600mm c/c staggered with chemical lockset grout etc. complete.

Providing & Constructing Size Stone Masonry in Super- structure in CM 1:6 in courses
41 not less than 150mm high complete as per specifications at all levels & Cum 50.00 0.00
Heights.(380mm thick)
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Extra Charges over above item for Two Line Dressing Exposed Stone Faces of size
stone masonry work at all levels & heights in courses not less than 150mm high. Both
faces shall be exposed & all sides of each stone flat chisel dressed true to square
42 Sqm 275.00 0.00
50mm wide alround & all corners shall be two line dressed 50mm wide all round & all
joints shall be scraped 12mm deep complete as per specifications. The edges are to be
dressed correct to square & line as directed at all levels & Heights.

Providing sunk pointing to Stone Cladding works with CM 1:3. The depth to which
pointing should be sunk should be 10 mm deep and should be finished semicircular at
43 all levels and heights including using approved quality and brand water proofing Sqm 815.00 0.00
compound Manufactured by Fosroc, Bal Endura, Sika mixed at the rate of 2 % by
weight of cement complete as per specifications.

TOTAL FOR MASONRY WORKS 0.00

I PLASTERING WORKS
Note: For all Internal & External Plastering works - M-Sand shall be approved as
per relevant BIS standands
General Note applies to all plastering works:The rate for all plastering item is to be
inclusive of - Making of grooves, Bands,drip moulds,at Wall and Ceilings junctions and
at Above Skirtings, and making good with Cement mortor all the chasings / chippings,
Bore packings done for other services such as Electrical, PHE, Fire, HVAC, etc.with
fixing of Arpitha/suchitra industries Plastering mesh of 125mm width in
single/double layer as required at junction of column/beam and other concrete surface
with masonry, to be fixed prior to plastering with necessary nail/screw etc,
complete.Waterproofing compound to be used as required to Borepackings to make it
water tight from any leakages.with all necessary staging, scaffolding internal and
external.

Providing 12mm thick cement plaster in single coat with cement mortar 1:3 to CEILING
including finishing as directed, rounding of corners, grooves, wherever required with
smooth rendering. Providing and removing scaffolding, including curing, cost of all
44 materials, labour, HOM of equipments and machineries, leads , lifts at all Levels and Sqm 50.00 0.00
heights, Loading and unloading charges, transportation cost and conveyance , all other
incidental charges etc., complete for successful completion of work all as per
specifications and as directed by the Engineer-in-charge.

Providing One coat of 12mm Base Coat cement Plaster and 6mm Finishing Coat
cement Plaster with cement mortar 1:4 to block masonry/ concrete surfaces, finish as
directed including providing and mixing water proofing compound at one Kg per bag or
in the proportion recommended by the manufacturers rounding off corners wherever
required, providing and removing scaffolding, including cost of all materials, labour,
curing, HOM of equipments and machineries, including leads and lifts at all levels &
heights, Loading and unloading charges, transportation cost and conveyance , all other
incidental chargesetc., complete for successful completion of work all as per
45 Sqm 1850.00 0.00
specifications and as directed by the Engineer-in-charge. The rate to include plastic
mesh 100mm wide manufactured out of hop dipped galvanised iron of nominal
thickness 0.35mm with a zinc coating of 120gms per sqm width, along route of walls
chipped for services, junctions between RCC & Porotherm/Solid Blocks including leads
and lifts at all Levels ,cost of materials, labour for fixing complete as per specifications.
No Extra cost shall be paid for Double Heights areas . (For Internal walls, external
wall surfaces, Stone Cladding Walls, All Ducts, Lift Shafts, Base coat plaster for
Dadoing area)

TOTAL FOR PLASTERING WORKS 0.00

J PAINTING WORKS
Approved Brand of Paints - Asain Paints, Berger, Nerolac, Johnson & Nicholson,
Nippon
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Providing One coat of "Super Snowcem" or equivalent paint over one coat of primer
complete as per manufacturers specification for all Lift shafts,Fire,PHE, Electrical and
46
any other Service duct. With all lead and liffts at all levels and heights including all
necessary staging and scaffolding etc complete.
For Lift Shaft & All Service Shafts Sqm 250.00 0.00
Providing and applying Birla White wallcare putty-SF or equivalent to walls & Ceiling in
two coats total thickness of the coats limited to a maximum of 1.5mm. The surface
should be thoroughly cleaned of all loose material and shall be clean, free from dust,
grease and loose material and shall be fully cured with clean water. Mixing and
application of putty shall be as per manufacturers instructions. including preparing the
47 Sqm 550.00 0.00
surface, even and sand paper smooth, cost of materials, labour, HOM of equipments
and machineries, including leads and lifts at all levels & Heights, Loading and
unloading, transportation , all other incidental charges at all floor levels etc., complete
all as per specifications and as directed by the Engineer-in-charge. No Extra cost shall
be paid for double height areas

Providing and applying painting in two coats with PLASTIC EMULSION Paint over a
coat of primer of approved brand and shade to give an even approved shade after
48 throughly brushing the surface, free from mortar drops and other foreign matter
including preparing the surface even and sand paper smooth, including lead & Lift lift at
all levels & heights, cost of materials, labour complete as per specification.

For Internal Walls & Ceiling Sqm 550.00 0.00

Providing Textured paint of approved quality, colour and shade to wall surface after
cleaning and rubbing the wall surface with wire brush of medium size emery stone to
remove all the loosely adhering particles, the surface is then cleaned with water and
ensured that it is in line and level. The Textured material is then mixed with 40-50% of
clean water untill a homogenous thick slurry is formed, the slurry is left for 5-10 min, to
49 react completly with ingredients. The textured finish prepared as above is then applied Sqm 140.00 0.00
to the wall surface with suitable roller/spray/gun/putty/blade/trowel to get the desired
finish. The finished surface shall be applied with two coats of exterior paint of approved
shade. The rate includes providing and removing scaffolding, including lead & lift and
Lift at all levels & heights and all other incidental charges etc. complete as per
directions of the engineer-in-charge of the work.
TOTAL FOR PAINTING WORKS 0.00
K FLOORING WORKS
Vitrified Tiles of various sizes Shall be of Kajaria/Nitco/Somany/Johnson/RAK or
equivalent.
Note: Basic Price of all materials
Vitrified tile 300mm x 600mm - Rs. 60/Sft
18mm to 20mm thick Water Cut Sira Grey Granite - Rs. 120/Sqft
18mm to 20mm thick Polished Steel Grey Granite - Rs.140/Sft
18mm to 20mm thk Flamed Finish Sira Granite - Rs. 140/Sft
Anti-Skid Vitrified tile 600mm x 600mm - Rs. 60/Sft
50mm thk flamed finish sira Granite for Treads - Rs.225/Sft

Providing and laying 40mm thick granolithic flooring (IPS Flooring) for Electrical Panel
Room consisting of 28mm thick 1:2:4 cement concrete base with coarse aggregate of
10mm and down size and 12mm thick top layer of crushed granite chips and cement,
50 Sqm 35.00 0.00
mixed with (1:1.5) one of cement to 1.5 parts by volume of crushed granite chips 6 mm
maximum size including finishing smooth complete as per specifications. Unevenness
more than 2 mm in one square METRE will not be accepted.

Providing and laying flooring with machine polished Tandur Stone 20 to 25mm thick
machine polished and hand cut of approved quality of size 600 x 600 mm,
600mmx900mm laid over a bedmortar of CM 1:4, 20mm thick including polishing three
51 Sqm 1010.00 0.00
coats, washing with oxalic acid with a final coat of wax polish. including curing, acid
washing, cleaning, protecting the floor with POP/bubble board,etc complete as per
detailed drawing.
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Providing and laying flooring with Rough Tandur Stone 20 to 25mm thick machine
polished and hand cut of approved quality of size 600 x 600 mm, 600mmx900mm laid
52 Sqm 135.00 0.00
over a bedmortar of CM 1:4, 20mm thick, including curing, acid washing, cleaning,
protecting the floor with POP/bubble board,etc complete as per detailed drawing.

Providing and fixing 20 to 25mm thick polished Tandur stone slabs of approved quality
and size for skirting of 50mm high set in CM 1:4, 20mm thick complete as per
53 Rmt 465.00 0.00
specifications including machine cutting sides and machine polishing. The joints will
have to be grouted with white cement.

Providing and laying flooring with machine polished Kotah slabs 18 to 25mm thick
machine polished and hand cut of approved quality of size 600 x 600 mm, 600
x1200mm laid over a bedmortar of CM 1:4, 20mm thick with 6 mm spacers. The spacer
54 joints shall be neatly grouted with grey cement and water proofing compound with Sqm 95.00 0.00
coloured pigment to match color of slab, including polishing three coats, washing with
oxalic acid with a final coat of wax polish. including curing, acid washing, cleaning,
protecting the floor with POP/bubble board,etc complete as per detailed drawing.

Providing and fixing 18mm to 20mm thick Water Cut Sira Grey granite slab for Lift Front
cladding (Wet Cladding) of approved sizes and pattern with all necessary grovees,and
55 polishing of all exposed edges etc, required over a backing of CM 1:3,12 mm thick, Sqm 25.00 0.00
including pointing with matching color cement to match the color of slab etc., complete
as per specifications and as directed by the architects. (Basic Price Rs. 120/Sft)

Providing & laying 18mm to 20mm thk Flamed Finish Sira Granite slabs for Staircase,
Treads, risers and Skirting set over a bed of 20 mm thick in CM 1:4, including providing
nosing edges chamfered / rounded and edge flamed, curing cleaning, protecting with
POP/bubble board as directed by the Architects with anti-skid grooves wherever
56 Sqm 55.00 0.00
necessary or as directed, etc. The Rate to include making groove of 10mmx10mm or
8mmx8mm in the riser granite slab along the bottom where it meets with tread etc
complete as per detailed drawing
(Basic Price Rs. 140/Sft)

Providing & laying 18mm to 20mm thk Flamed Finish Sira Granite Slabs for flooring of
approved size machine cut slabs laid in pattern as directed over a bed mortar 20mm
57
thk in CM 1:4 including cement paste backing, pointing, curing, cleaning and protecting
the floor with POP/bubble board,etc, complete. (Basic Price Rs. 140/Sft)

Staircase Lobby, Staircase Mid-Landing areas Sqm 150.00 0.00

Providing and laying Anti-Skid Vitrified Tile flooring for Toilets of size 600mmX600mm
and 10mm thick of approved make, finish & color set over a bed of cement mortar 1:4,
20mm thick with 3mm thick spacers. The Spacer Joints shall be neatly grouted with
58 matching color cement and pigment with waterproof compound to match the color of Sqm 55.00 0.00
slab including acid washing, protecting the floor with POP/bubble board complete.
Tiles of appvd size to be laid to pattern given by Architects, complete as per
specifications. (Basic Price Rs. 60/Sft)
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Providing and laying Dadoing in toilets, Handwash with Vitrified Tiles of Size
300x600mm Matt Finish with 3mm spacers using Gold Star adhesive, from Ardex
Endura/ Webber SGG / SIKA/ or any other equivalent of grey - highly polymer
modified - high strength - flexible adhesive, by mixing it with clean water in ratio of 4
part of powder to 1 part of water by weight in suitable sized mixing vessel using slow
speed heavy duty drilling machine fixed with mixing paddle, until a slump free mortar is
obtained, combing of adhesive at minimum of 3-6mm thick for wall / floor area using
59 Sqm 385.00 0.00
steel notch trowel, fixing of tiles by gently tamping them by rubber mallet, removing
excess adhesive from the joint, making tile surface ready for grouting process and
allowing it to dry completely, etc and complete as per manufacturer's specification. The
spacer joints shall be neately grouted with matching color cement & Pigment with
waterproof compound to match the colour of tile including acid washing etc complete.
Tiles of appvd size to be laid to pattern given by Architects, complete as per
specifications. (Basic Price Rs. 60/Sft)
Providing and fixing 18mm to 20mm thick 250mm wide for Copings Flamed Finish Sira
Granite in CM 1:3 for corridors railings, Planter box top coping & side cladding etc
60 including rounding of exposed sides and polishing and making holes for insertion of Sqm 45.00 0.00
S.S. railings/MS railings etc. complete as per drawing
(Basic Price Rs. 140/Sft)

For Ramps Staggered : Providing & laying 18mm to 20mm thick Flamed Sira Granite
for flooring & Skirting laid over bed of 20mm thick 1:4 cm & jointed with neat cement
61 slurry mixed with pigment to match shade of granite slabs including laying POP/Bubble Sqm 16.00 0.00
board on finished surface and cleaning the surface, including the cost of materials and
labours etc complete as per specifications. (Basic Price Rs. 140/Sft)

Providing & laying Machine cut Edges 50mm thk Flamed finish Sira Granite for Treads
of approved size machine cut slabs laid in pattern as directed over a bed mortar 20mm
62 thk in CM 1:4 including cement paste backing, pointing, curing, cleaning and protecting Sqm 7.00 0.00
the floor with POP/Bubble board, etc, complete.
(Basic Price Rs. 225/Sft)
Providing & laying Machine cut Edges 50mm thk Flamed finish Sira Granite for 380 th
SSM Walls Top Copings of approved size machine cut slabs laid in pattern as directed
63 over a bed mortar 20mm thk in CM 1:4 including cement paste backing, pointing, Sqm 25.00 0.00
curing, cleaning and protecting the floor with POP/Bubble board, etc, complete. (Basic
Price Rs. 225/Sft)
Providing and fixing 18mm to 20 mm thick Polished Finish Steel Grey Granite for
Pantry platforms, Wash Basin counters, Serving Counter Side Cladding, Ledge Wall
Top Coping in toilets set on a bed of cement mortar 1:4, 20 mm thick including cutting
64 for counter sunk wash basins to the required shapes and sizes and drilling holes for Sqm 55.00 0.00
taps, gas pipes etc., rounding of corners and edges, and polishing, pointing the joints
with matching color pigment complete as per detailed drawings. Basic Price Rs.
140/Sft)
Providing & laying 150mmx150mm square paver blocks (shot blasted) 60mm thk &
above of "Basant Beton/Parijatha/Shoba " or appvd make equivalent type of Grey
65 Sqm 255.00 0.00
colour set on a sand bed of 50 mm thick laid to pattern given by the Architects. (Basic
Price Rs. 70/Sqft)

Removing and Re-Laying of Chapadi Stone over a bedmortar of CM 1:4, 20mm thick
66 including laying to required slope to drain out the rain water including disposing of all Sqm 40.00 0.00
the debris generated outside the campus as directed by Engineer-in-charge.

Removing & Re-Laying of Interlocking pavers set on a sand bed of 50mm thick laid in
pattern given by the Architects including disposing of other un-usable materials outside
67 the premises or as directed by the Engineer - in charge and making good all the Sqm 150.00 0.00
andulations to required line & level to receive the Interlock pavers at all levels and
heights etc complete.
TOTAL FOR FLOORING WORKS 0.00
L RAILING WORKS
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Providing, fabricating & fixing Stainless Steel Handrails as Grab Bars ( Side Railing)
using 40mm dia pipes for horizontals and SS 12mm dia pipe and 20mm dia pipe for
68 verticals with brush steel finish and 2mm thk of grade SS304 at intervals of 1.2 Mtrs or Rmt 23.00 0.00
as per site condition and as per detailed drawing including welding, fixing, grouting,
grinding, polishing, anchoring to RCC / masonry works, etc; complete.

Providing, fabricating & fixing Stainless Steel Handrails 350mm high using 40mm dia
pipes for horizontals and SS 12mm dia pipe and 40mm wide x 10mm thick SS Flat for
69 verticals with brush steel finish and 2mm thk of grade SS304 at intervals of 1.2 Mtrs or Rmt 140.00 0.00
as per site condition and as per detailed drawing including welding, fixing, grouting,
grinding, polishing, anchoring to RCC / masonry works, etc; complete.

TOTAL FOR RAILING WORKS 0.00

M ALUMINIUM GLAZING WORKS
Alumnium Fixed Ventilators For Toilets: Providing and fixing Powder coated fabricated
as per drawing using aluminium extruded sections powder coated to the required finish
as approved by the Architects and glazing with 6mm thick Froasted glass of SGG/
Ashai / Atultuf, or any other approved make, complete as shown in the drawing. The
70 quoted rate to include frame work for fixing Exhaust fans and powder coating of Sqm 6.00 0.00
approved color, shade and finish powder coating of minimum thickness 40 micron as
per relevant IS specifications instead of natural anodizing.Aluminium sections shall be
of Jindal/ HIndalco/Bhoruka. (Powder Coating shade Code Shall be RAL
7005/Equivalent)
Providing and fixing powder coated aluminium ventilator with fixed glass louvers
fabricated as per drawing using aluminium extruded section powder coated 40mm th
Microns to the required colour and finish as approved by the Architects ,and glazing
71 Sqm 4.00 0.00
with 4mm thick plain clear sheet glass, ground glass and/or pin headed glass of
approved make including providing all necessary fixtures,fittings, complete as shown in
the drawing.

Providing & fixing aluminium glazed windows sliding windows with glazed openable
single and/or double leaf shutters, with two tracks aluminium frames with mosquito
frames hinged or pivoted, with or without side lights and fan lights with fixed glazing,
fabricated as per drawing using aluminium extruded sections of
"JINDAL/HINDALCO/Bhoruka make as per details shown in the drawing to the
required finish as approved by the Architect's. Glazing will be with 6 mm thick Plain
72 Clear glass of IAG / SAINT GOBIN / ASHAI or approved equivalent make. Each shutter Sqm 20.00 0.00
will have approved type handles as shown in the drawing on both sides. The door shall
have approved concealed locking arrangement with duplicate keys, concealed tower
bolts with Silicon Sealant, etc.; complete as per drawing. Extra over the above quoted
rate for Providing approved color and finish, quality Powder Coating of minimum
thickness of 40 micron as per relevant IS specification instead of natural anodising.
Powder Coating shade Code Shall be RAL 7005/Equivalent)

Providing & fixing aluminium glazed windows sliding windows with glazed openable
single and/or double leaf shutters, with three tracks aluminium frames with mosquito
frames hinged or pivoted, with or without side lights and fan lights with fixed glazing,
fabricated as per drawing using aluminium extruded sections of
"JINDAL/HINDALCO/Bhoruka make as per details shown in the drawing to the
required finish as approved by the Architect's. Glazing will be with 6 mm thick Plain
73 Clear glass of IAG / SAINT GOBIN / ASHAI or approved equivalent make. Each shutter Sqm 6.00 0.00
will have approved type handles as shown in the drawing on both sides. The door shall
have approved concealed locking arrangement with duplicate keys, concealed tower
bolts with Silicon Sealant, etc.; complete as per drawing. Extra over the above quoted
rate for Providing approved color and finish, quality Powder Coating of minimum
thickness of 40 micron as per relevant IS specification instead of natural anodising.
Powder Coating shade Code Shall be RAL 7005/Equivalent)
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Providing and fixing Powder coated aluminium glazed windows with fixed glazed
portion for Windows fabricated as per drawing using aluminium extruded sections
powder coated to the required finish as approved by the Architects and glazing with
6mm thick plain clear sheet glass ofSGG/ Ashai / Atultuf, or any other approved make,
74 Sqm 2.00 0.00
complete as shown in the drawing. The quoted rate to include for providing approved
color, shade and finish powder coating of minimum thickness 40 micron as per relevant
IS specifications instead of natural anodizing.Aluminium sections shall be of Jindal/
HIndalco/Bhoruka.

Aluminium Top Hung Windows: Providing and fixing Powder coated Fabricated as per
drawing using aluminium extruded sections powder coated to the required finish as
approved by the Architects with all necessary Friction hinges etc complete and glazing
with 6mm thick Plain Clear Glass of SGG/ Ashai / Atultuf, or any other approved make,
75 Sqm 4.00 0.00
complete as shown in the drawing. The quoted rate to include for providing approved
color, shade and finish powder coating of minimum thickness 40 micron as per relevant
IS specifications instead of natural anodizing.Aluminium sections shall be of Jindal/
HIndalco/Bhoruka. (Powder Coating shade Code Shall be RAL 7005/Equivalent)

Providing and fixing powder coated aluminium mosquito proof mesh sliding windows
with outer frame 2 track 64mmx32mm and shutters with 40mmx18mm sections with
76 infill of sleek mesh sections 45mmx10mm with SS black powder coated 0.21mm thick Sqm 30.00 0.00
mesh count 18x16, rubber beed, star lock, metal wheels etc complete as per
specifications.
Providing and fixing 8mm thick Froasted glass for Glass partition fixed over U channels
at bottom and top. Rate to include the sealant to be applied for the glass joints and for
77 Sqm 3.00 0.00
the channels. All edges of the glass to be polished etc complete as per detailed
drawings.
Providing and fixing Skylight glass made up of 6mm+1.52+6mm toughened laminated
glass of Saint Gobain/Ashai/ Atultuf fixed along with Aluminium subframe, Isolators,
78 Pressure plates, Neoprene Rubber cushion 4 to 6mm thick, flashing and Silicone Sqm 350.00 0.00
sealant complete. The system is to be tested for water tightness and got approved from
EIC.
TOTAL FOR ALUMINIUM GLAZING WORKS 0.00
N GENERAL PURPOSE METAL DOORS .
Providing and fixing of General Purpose Single & Double shutter Hollow metal doors at
all levels from ISO 9001-2000 certified Manufaturer from M/s. Shakti Harmon or M/s.
79 Bangalore Protech Controls Pvt Ltd Pressed Galavanised steel Single/Double leaf to
required sizes of approved make which consists of frame, shutter, infill and finish as
detailed below and conforming to IS 277.
Door frame shall be double rebate profile of size 100x57mm made out of 1.20mm thk
galvanised steel sheet (18 gauge). Frames should be MITERED & field assembled
with self tabls. Door should be 46mm thk, double skin door shell & manufactured from
0.8mm thick galvanized steel sheet (22 gauge).The infill material shall be resin bonded
honey comb paper glued and sandwitched in between with an interlocking
arrangements. All Vision lite panels wherever applicable should be of size
300mmx300mm and 250 x450mm as per detailed drawing & Kick plates. All doors
should be factory preped for receiving appropriate hardware & provided with necessary
reinforcement for hinges, locks & door closers. All door frames should be provided with
SOFIT bracket and anchor fastners for installation on a masonry opening. Once frame
installed should be grouted with cement slurry necessary for doors on clear masonry
opening. Door frames and shutter shall be finished with etched primer coating (35
microns), stoved zinc phosphate primer and themosetting polyurathene aliphtic grade
paint (35 micron DFT) of approved colour.
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Rate shall include for supply and installation of hardwares for doors from
DORMA/HAFFLE/SWAY for ball bearing hinges, mortice lever lock, door closers and
anyother hardwares, etc. All glass should be fixed with a clip on arrangement with no
visible face fixed screws. (Color Code Shall be - Off-white/Morning Glory/Equivalent)

1) Door Size - 2.0 m x 2.4m No 2.00 0.00

2) Door Size - 1.5m x 2.4m No 2.00 0.00

3) Door Size - 1.2m x 2.4m No 4.00 0.00

4) Door Size - 0.9m x 2.4m No 1.00 0.00

TOTAL FOR GENERAL PURPOSE METAL DOORS 0.00
O LAMINATED PARTITIONS FOR TOILETS

Providing & fixing Laminated toilet Cubicles from Green ply industries/Merino
Industries/Century as approved by Architects of 12mm thickness, colour with HPL
80 boards, of size as per drawing with accessories like hooks, privacy thumb turn
indicator, Gravity hinges, Door Knob, Adjustable leg, top profile and U channel with the
other necessary accessories as per manufacturer's specifications.

MODLE TYPE : Green Sturdo Vibrance Series Serene Model

Color of HPL Boards : As Per Green Sturdo Shade Card as mentioned Below

Green lam laminates, Abstract, 923 Meta silver, Compact laminate,

Thickness of Compact Laminate : 12mm
Overall Height of Cubicle : 1995mm (including bottom gap 150 mm)
Accessories: Standard – Aluminium, Nylon accessories
a) Nylon Adjustable foot
b) Aluminum Channel
c) Nylon Gravity hinges
d) Coat Hook
e) Stainless Steel Door Knob with lock set indicator
g) Rubber Door Stopper Lining
h) Screws & Wall Plugs
i) Aluminium Top Rail
a) For Water Closets of size : 1.85 Mtr x 1.15 Mtrs Sqm 17.00 0.00
b) For Water Closets of size: 1.5m x 0.9 Mtrs Sqm 6.00 0.00
TOTAL FOR LAMINATED PARTITIONS FOR TOILET 0.00

P WOODEN DOORS

For Toilets: Providing and fixing Teakwood frames for Toilets of 62mm x 125mm and
six MS hold fasts 40x5mm, 40 cms long embedded in cement concrete 1:3:6, 20 cms
thick and 30 mm thick flush door shutters Veneered on one side and laminated on other
81 Sqm 12.00 0.00
side of approved colour solid core with teakwood lipping alround with SS hinges and all
other necessary hardwares, other details confirming to IS No. 1969-1960 & 2202 Part-
1, 1962 as modified to date of "Kutty" manufacture and rate to include all fittings.

Providing and fixing sliding door with 30mm thFlush shutters with solid TW lipping
alround and locking arrangement with coburn gear fitting on top and guide channels at
the bottom. 30 mm thick flush door shutters laminated on One Side & Veneered on
82 Other Side of approved colour & Shade with all necesary hardwares, SS Hinges and Sqm 5.00 0.00
all locking arangements etc complete, and other details confirming to IS No 1969-1960
& 2202 part-1, 1962 as modified to date , flush shutters to be manufactured by Kutty or
any other equivalent all as per detail drawing.
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Providing & spraying Melamine polish of approved colour, shade for wood works with
83 Sqm 20.00 0.00
all necessary base preparation as directed.
Providing and Fixing of Ball Bearing Butt Hinge, SS 404,SSS, 4"x3"x3mm-2BB, Square
84 No 20.00 0.00
Corner with Timber Door Screw.
Providing and Fixing of Mortise Cylinder Dead Lockcase, 55mm backset, 24mm
85 Forend, SS Matt with all necessary screws etc to the required heights levels etc as per No 5.00 0.00
the detailed drgs etc, complete.
Providing and Fixing of Euro Profile Thumb Turn Cylinder with Key, 31.5+31.5 = 63mm,
86 No 5.00 0.00
Matt Nickel.
87 Providing and Fixing of Euro Profile Cylinder Escutcheon Press-in, SS Matt. No 5.00 0.00
Providing and installing S Steel " D " type Pull Handle Back to Back Fixing 25mm Dia x
88 No 5.00 0.00
300mm high.Brush steel finish with Necessary Screws.
Providing and Fixing Door Closer - DIV78, with Hold Open Arm, Size 2/3/4, For upto 80
89 Kg inclusive of making adjustments and sorting it for smooth operation, etc; complete No 4.00 0.00
all as per specifications.
TOTAL FOR WOODEN DOORS 0.00
Q SHERA BOARD FOR DUCT COVERING
Providing and fixing 12mm thick Shera Board on MS frame work made of RHS / SHS of
50mm x50mm for Duct coverings of various size with Door openings for regular
maintenance with all necessary hinges,handles, and locking arrangement. at specific
90 places at each floor as mentioned in the drg. The Shear Board to have perforations as Sqm 15.00 0.00
per the detailed drawing. The Rate to include painting with 2 coats of synthetic Enamel
paint over a coat of primer for Shera Board & MS frame works of approved colour &
shade.
TOTAL FOR SHERA BOARD FOR DUCT COVERING 0.00
R FALSE CEILING WORKS

Providing & fixing "ARMSTRONG PRIMA ADRIA / AEROLITE" True Horizontal

Level False Ceiling with Grid using hot dipped galvanised steel section exposed
surface chemically cleaned capping pre-finished in baked polyster paint, main Tee of
size 15x38x0.33mm at every 1200mm c/c max & rotary stitched cross "T" of size
15x38x0.254mm at every 600mm c/c maximum between main runners, 600mm cross
91
Tee of size 15x38x0.254mm at every 1200mm centrally between 1200mm cross tees &
22x22x0.457mm wall angle alround wall to form a grid of size 600x600mm &
suspended grid using suitable rigid hangers at every 1200mm intervals at main "T" &
laying of size 600x600x15mm over frame grid. The false ceiling should be laid to
pattern as shown in drg. Work should be as per manufacturer's specification.

NOTE: Cutouts for light fittings, grills, diffusers, etc have to be made with frame of
perimeter channels of size 20x27 mmx30mm, 0.5mm thk supported suitably and should
Sqm 40.00 0.00
be included in the above rates and no extra rate will be paid for. Rate to include
staging, scaffolding, etc. at all levels and heights.
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Providing and installing Suspended Moisture Resistant Ceiling includes Gypsteel

ULTRA Perimeter Channel Fixed along the perimeter of existing wall / Partition with the
help of nylon sleeves and screws, at 610 mm centres. Gypsteel ULTRA Ceiling angle is
suspended at desired height by fixing it to the soffit with the Gyproc Soffit Cleat and
Anchor Fastener creating 1220 mm x 1200 mm grid. Gypsteel ULTRA Intermediate
channel is fixed to the Gypsteel ULTRA Ceiling angle with M6 Nut and bolt
arrangement. The Gypsteel C Ceiling is then fixed to the Gypsteel ULTRA Intermediate
Channel with the help of Gyproc Connecting Clip and in direction perpendicular to the
Gypsteel ULTRA Intermediate channel at 457 mm c/c. Single layer of 12.5 mm thk
tapered edge Gyproc MR (conforming to IS 2095 Part 1:2011) is then screw fixed to
ceiling section with 25 mm drywall screws at 230 mm centres. Finally square and
tapered edges of the boards are to be joined and finished so as to have a flush look
92 which includes filling and finishing with Gyproc Jointing Compound & Gyproc Joint Sqm 17.00 0.00
Paper tape only (as per recommended practices of Saint-Gobain Gyproc India). Gyp
boards are to be joined and finished so as to have a flush look which includes filling and
finishing the tapered and square edge of the boards with gypsum roller net tape &
approved quality joining compounds. The work also includes vertical drops, curvature,
providing & making farma cutting of gyp boards & frame work and providing cutouts /
openings and additional supports wherever required for the fixing of ceiling fixtures like,
lights, A.C grills, sprinklers, smoke detectors etc. Finished surface is to be well
prepared & a top coat of primer alongwith 2 or more coats of plastic emulsion paint as
per manufacturers specfn to be done. Rate to include cost of scaffolding, staging,
providing openings for light fitting, fire alarm system. For cutouts made for light fixtures
etc perimeter channels supported suitably shall be considered in rate. Net area of fixed
gypsum board in horzontal or when done in vertical to be measured for payment.
TOTAL FOR FALSE CEILING WORKS 0.00
S WATERPROOFING WORKS

Providing Patented "Surface" method Specialist Water Proofing Treatment like "India
Water Proofing" or approved equivalent to terraces and sunken slabs (with guarantee
for 10 years)consisting of providing 112 mm average thickness brick bat coba to
achieve the required gradient for free flow of water over the terrace, and 'Cetroof'
93 jointless waterproof plaster finished smooth with trowel and treatment carried along Sqm 660.00 0.00
vertical surface of parapets and other adjoining walls to a height of 300 mm with a
round vata at the junction and finishing at the rain water pipe outlets etc; complete as
per the specialist’s specification. The area measured will be only the plan area and
treatment on the vertical walls will not be paid separately.

Providing Waterproof coating Brushbond RFX of 1 mm thickness for Terrace, Sunken

Slabs & UG Sump manufactured by M/s. Fosroc Chemicals. The material should
consist of a liquid polymer component and a cementitious powder component, which
shall be mixed as per manufacturer's instructions and applied over prepared concrete
94
surface strictly maintaining the cover-age specified by the manufacturer. The storage
mixing and application of the coating should be strictly as per manufacturer's
instructions. The rate is inclusive of material, labour, equipment hire charges, lead and
Lift at all levels & Heights etc complete.
a) For Terrace, Sunken Slabs & UG Sump Sqm 850.00 0.00

Water Proof Plaster for Sunken areas of Toilets, Lift Pit, UG Sump: Providing 15mm
thick cement plaster in single coat with cement mortar 1:3 to concrete surfaces
including providing and mixing water proofing compound at one Kg per bag or in the
proportion recommended by the manufacturers rounding off corners wherever required,
95 finish as directed, providing and removing scaffolding, including cost of all materials, Sqm 225.00 0.00
labour, curing, HOM of equipments and machineries, leads and lifts at all levels,
Loading and unloading charges, transportation cost and conveyance , all other
incidental chargesetc., complete for successful completion of work all as per
specifications and as directed by the Engineer-in-charge.

TOTAL FOR WATERPROOFING WORKS 0.00

T DISMANTLING WORKS
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Removing and Handing over of Existing Light Roof Structure comprising of MS

Columns, Trusses,Purlins,brackets, MS Sheets, Base plates Gussets, Grills, and all
other connected items, including cutting, chipping, excavating of Footings, bases of
96 Sqm 550.00 0.00
columns, Beams and handing over them in Good Condition and Stacking and Storing at
all levels and Heights as directied by the Engineer - in charge within the campus
including all lead and lifts.

Dismantling RCC cement concrete works like beams, slabs, floors, columns, footings,
rafts, etc with Diamond Cutting/Slicing of slab instead of conventional method including
cutting the reinforcement steel and disposing the debris outside the premises in places
approved by the relevant local Govt. authorities and steel removed to be stored as
97 Cum 15.00 0.00
directed within the site. All the structural members to be adequtely propped and to
ensure that during dismantling the adjoining structures shall not be disturbed or
damaged, and to make good all the damages done to its original shape and size with
all necessary Stagging & Scaffolding at all levels and Heights.

Dismantling of the Existing 380 th and above sizes of Dressed Size Stone masonry in
super structure manually / by Mechanical means including Transporting and Stacking of
the same anywhere within the Campus as Directed by Engineer-In-Charge and
98 Cum 125.00 0.00
disposal of unserviceable materials outside the premises at places approved by the
relevant local govt. authorities. with all necessary lead & lifts, Stagging, Scaffolding at
all heights and levels as per direction of Engineer Incharge.

Dismantling of the Existing Size Stone Masonry in foundation manually / by

Mechanical means including stacking of Stones to be re-used and disposal of
99 Cum 75.00 0.00
unserviceable materials outside the premises at places approved by the relevant local
govt. authorities. with all necessary lead & lifts as per direction of Engineer Incharge.

Dismantling of Existing Flooring laid of Tandur / Chappdi / Stone slab flooring material
removed in good condtion which shall be re used and to be handed over in good
100 condition and stocked as directed by the Engineer - in charge and disposal of Sqm 700.00 0.00
unservicable materia / debrisl outside the premises at places approved by the relevant
local govt. authorities.

Removing and Handing over of Existing MS Grills & Grating comprising of MS L-

angles, Flats, RHS, SHS, Round Bar, Brite bars etc including cutting, chipping and
101 Sqm 25.00 0.00
handing over them in Good Condition and Stacking and Storing as directied by the
Engineer - in charge within the campus including all lead and lifts.

Demolishing of Existing brick work of 230 / 115 mm th manually/ by mechanical means

including plastering, Tiles, Dadoing, and clearing of the Debris Outside the Premises at
102 Cum 5.00 0.00
all Heights , levels, with necessary Stagging Scaffolding etc as per directions of
Engineer-in-charge.

Removing & Carefully Stacking out the existing Doors at places as specified by the
103 No 2.00 0.00
Engineer -in-charge within the campus.

Chipping & Removing bituminous road including soling, WBM, chip carpeting upto
thickness of 350mm including removing kerb and stacking. The debris to be cleared
104 Sqm 100.00 0.00
outside the premises and disposing it at places approved by the relevant local govt.
authorities.
Dismantling of the existing waterproofing work either surkhi or brickbat coba at terrace
including removing, cleaning and clearing the debris from terrace, transporting and
105 Cum 11.00 0.00
disposing outside the premises at places approved by the relevant local Govt.
authorities.
TOTAL FOR DISMANTLING WORKS 0.00
U MISCELLENOUS WORKS
 ` M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR CIVIL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

S. No Description Unit Quantity Rate Amount

Rs. Rs.

Providing and fixing RCC Hume pipe (NP2 class) across the foundation, below floors,
pavements, steps etc., including breaking, cutting the pipe to the required length, fixing
106
in position, providing and fixing the collars, sealing and making good the broken
foundation, floor etc., complete

a) 300mm dia Rmt 25.00 0.00

b) 150 mm dia Rmt 25.00 0.00

Barricading in vertical plane around construction site to a height of 6 mtrs made of
truss framework in MS angles spaced at regular interval of not more than 5mtrs,
connected with 3 or 4 nos of 50x50x6mm angles as purlines throughout for fixing the GI
107 Sqm 985.00 0.00
corrugated sheet. Contractor to maintain the barracading throughout the construction
and after completion of the project dismantle the same and remove the material from
the site.
Providing and fixing in expansion joints, 25 mm thick "Dura Board" of "M/s Supreme
Industries" or any other approved equivalent board including cutting to shape and
placing in position in floor slabs, etc at all levels & heights as directed. On the exposed
108 Rmt 100.00 0.00
edge, the board shall be 12mm inside concrete face including 12mm deep and 25mm
wide silicon sealant "pediseal", "Tuffseal" or equivalent sealant at all levels complete as
per manufacturers specifications.
Providing and fixing 6mm thick best quality mirror with 12 mm thick ply wood backing,
109 backing frame work and teak beading alround fixed with necessary screws and clamps Sqm 50.00 0.00
etc., complete.

Providing & fixing MS framed Weldmesh for Bird proof Mesh using MS angle
110 frames,flats,etc and Weldmesh of size 25x25mm of 10G fabrica-ted as per drg includin Sqm 40.00 0.00
fixing at all levels withpainting 2 coats of synthetic enamel over a coat of primer. Etc

Providing & fixing RCC 1:2:4 Precast Saucer Drains of Size 100x 300mm each piece
not less than 600mm long each piece not less than 600mm long including Excavation
inin all soils including hard soil, backfilling & consolidating with excavated earth &
carting away the surplus earth away from site. Providing and placing Plain Cement
111 Concrete M10 - 100 mm thick , Below Foundations for plugging Kerb stone etc, using Rmt 50.00 0.00
coarse graded aggregates of 20 mm and down size, laid in layers and compacted by
wooden or cast iron rammers including necessary shuttering , finishing, curing etc
complete, fixing the Kerb stone to the required line, height and alignment & pointing
joints with CM 1:3 to the required line and level.

Providing, Fabrication and installing Trough ( Wash Basins) using 20mm thick,
"BIANCO NEVE QUARTZITE", Stones slabs fabricated to the required shapes and
sizes, the Base shall be made of 12mm th high quality Boiling Waterproof Plywood to
the required shape and size as per the detailed drgs.The Joints of the Quartzite stone
112 shall be treated with Epoxy Sealents to make it water tight and polished for seamless Sqm 40.00 0.00
uniform finish , with drilling and making of holes for insertion of Sink drains,Taps and
any others as required in Plywood and Stone slabs and making it good with necessary
Epoxy sealents. The MS frame work required to support this Wash basin Trough shall
be measured and paid under Structural Steel item.
TOTAL FOR MISCELLANEOUS WORKS 0.00
 M/s. Indian Institute of Management, Bangalore
ABSTRACT ESTIMATE FOR WATER SUPPLY WORKS, PLUMBING WORKS AND RE-ROUTING OF EXISTING LINES FOR
CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN
Sl No Description Amount
Rs.
INTERNAL PHE WORKS

I SANITARY FIXTURES 0.00

II SOIL, WASTE, RAINWATER AND VENT PIPE SYSTEM 0.00

III WATER SUPPLY SYSTEM 0.00

IV HOT WATER SUPPLY SYSTEM 0.00

V RE-ROUTING WORKS 0.00

TOTAL 0.00
GST, EXTRA AS APPLICABLE
 M/s. Indian Institute of Management, Bangalore
ESTIMATE FOR ESTIMATE FOR WATER SUPPLY WORKS, PLUMBING WORKS AND RE-ROUTING OF EXISTING LINES FOR CONSTRUCTION OF DINING
BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN
Sl No Description Unit Quantity Rate Amount
Rs. Rs.
I SANITARY FIXTURES & FITTINGS

Supplying, fixing, testing & commissioning of approved make white glazed

European water closet wall mounted type with concealed cistern. The quoted price
shall also include all internal parts of the cistern with white colour plastic solid seat
1
and cover with rubber buffers and flap, heavyduty plastic hinges, CP brass wall
plate complete including 110mm dia WC connector & silicone sealant .(For all
toilets)
EWC - Make - Parryware - Model - CARDIFF CODE - C0264
Seat Cover - 38138 CARDIFF
Cistern - Make - GABRIT - Model - 110.120.00.1
Extension Bolts - Viking
Flush Plate - make - ACTUATOR PLAT - CHROME - C821399

Supply Nos. 8.00 0.00

Fixing Nos. 8.00 0.00

Supplying,testing & commissioning of approved make white glazed oval wash basin
white colour below counter 15mm Long body C.P. pillar Cock, 32mm dia CP waste
coupling, 32mm dia C.P.bottle trap with C.P. extension pipe,C.P.spreader unit GI
2
expansion bolts, supporting bracket with necessary steel to support basin 1
No.15mm CP angle valve with 450mm long CP connection pipe and CP wall
flanges all of approved make etc., complete.
Wash Basin - Make : Parryware. Model - GENEVE N - C0441
CP Fitting - Make - Jaquar
Pillar Cock - 'FUS-CHR-29001
Bottle Trap - Model - ALD-CHR-769L250X190
Angle Cock - Model - 'FUS-CHR-29053
Waste Coupling - Model - ALD-CHR-709
Supply Nos. 6.00 0.00

Fixing Nos. 6.00 0.00

Supplying,fixing, testing and commissioning of white glazed Rectangular wash
basin, 15mm dia CP pillar cock auto closing system with waste coupling, 32mm
dia CP bottle trap with extension pipe, supporting bracket with necessary steel to
3
support basin 1 No.15mm CP angle valve with 450mm long CP connection pipe
and CP wall flanges all of approved make etc., complete. ( For Drivers & PWD toilet
).
Wash Basin - Make : Parryware. Model - C0406*(SP)/34(CTH)
CP Fitting - Make - Jaquar
Pillar Cock - 'FUS-CHR-29001
Bottle Trap - Model - ALD-CHR-769L250X190
Angle Cock - Model - 'FUS-CHR-29053
Waste Coupling - Model - ALD-CHR-709
Supply Nos. 2.00 0.00

Fixing Nos. 2.00 0.00

Supplying, fixing, testing and commissioning approved make white colored large
flat back urinals with 40mm C.P. dome type waste coupling 40mmC.P. bottle trap
4 with C.P. extension pipe, 15mm dia solenoid valve unit & Battery Operated Builtin
sensor unit for automatic flushing from urinal with necessary electrical etc.,
C.P.spreader unit GI expansion bolts etc., complete.( For Drivers toilet )
Urinal - Make : Parryware. Model - C0588
CP Fitting - Make - Jaquar
Bottle Trap - Model - ALD-CHR-769L250X190
Waste Coupling - Model - ALD-CHR-709
Supply Nos. 6.00 0.00

Fixing Nos. 6.00 0.00

Supplying, fixing, testing & commissioning sink with single bowl and single drain
board manufactured from 1mm thick stainless steel, 18G high grade indestructable
5 chrome nickel steel with top quality polish,1no.40mmdia CP waste coupling,with
1no. 40mm dia CP bottle trap with extension pipe,Sink mixer with wall flange with
aerator etc., complete. Size of sink : 1150mm x 500mm. ( For Pantries )

Sink - Make : Parryware. Model - C853699

CP Fitting - Make - Jaquar
Sl No Description Unit Quantity Rate Amount
Rs. Rs.
Sink Mixer -'FUS-CHR-29165
Bottle Trap - Model - ALD-CHR-769L250X190
Angle Cock - Model - 'FUS-CHR-29053
Waste Coupling - Model - ALD-CHR-709
Supply Nos. 2.00 0.00

Fixing Nos. 2.00 0.00

Supplying, fixing & testing 15mm CP health faucet of approved make with
6 necessary CP flexible hose 1000mm long nozzle,CP wall flange, CP angle cock
etc., complete.
Health Faucet - Make - Jaquar. Model - ADL-CHR-577
Angle Cock - Model - 'FUS-CHR-29053
Supply Nos. 8.00 0.00

Fixing Nos. 8.00 0.00

7 Supplying, fixing CP toilet paper holder fixed with SS screws complete.
Make - Jaquar. Model - ACN-CHR-1151N
Supply Nos. 8.00 0.00

Fixing Nos. 8.00 0.00

8 Supplying,fixing CP twin coat hook fixed with SS screws on to the toilet door.
Make - Jaquar. Model - CAN-CHR-1161N
Supply Nos. 8.00 0.00

Fixing Nos. 8.00 0.00

Supplying,fixing & testing 15mm CP bib cock with CP flanges including necessary
9
fixing materials etc.,complete.
Make - Parryware. Model - 'G3104A1
Supply Nos. 4.00 0.00

Fixing Nos. 4.00 0.00

Supplying,fixing approved make CP towel ring fixed on to wall by using with SS
10
screws in the pantrys.
Make - Jaquar. Model - ACH-CHR-1121 N
Supply Nos. 6.00 0.00

Fixing Nos. 6.00 0.00

Supplying,fixing of 15 mm dia CP angle cocks for water purifier provision for Pantry
11
etc.
Make - Jaquar. Model - 'FUS-CHR-29053
Supply Nos. 6.00 0.00

Fixing Nos. 6.00 0.00

Fixing Push ABS liquid Soap dispenser of 1000ml of capacity of approved make
12
with necessary fixing materials etc.complete
Make - Nova tech /Approved Equivalent ; Model - NTS03
Supply Nos. 10.00 0.00

Fixing Nos. 10.00 0.00

Supplying,fixing, testing and commissioning of approved make Electric Hand Drier
13 twin blower integrated with timer (0-3 minutes) and infrared arrangement. The drier
shall be fully automatic.
Make - Nova tech /Approved Equivalent ; Model - NT800
Supply Nos. 4.00 0.00

Fixing Nos. 4.00 0.00

Supplying, fixing of approved make SS body Paper Towel Dispenser with
14
necessary screws, Clamps etc., complete.
Make - Nova tech /Approved Equivalent ; Model - NTP04S
Supply Nos. 10.00 0.00

Fixing Nos. 10.00 0.00

Supplying,fixing of CP 20mm dia 600mm long grab bar with CP flanges, fixed with
15
SS screws complete. - Fixed in handicapped toilets.
Make - Jaquar. Model - 'CON-CHR-1101N
Supply Nos. 3.00 0.00

Fixing Nos. 3.00 0.00

Sl No Description Unit Quantity Rate Amount
Rs. Rs.
Supplying, fixing and testing Neer make- Model No - NCO 8001 Nickel and Bronze
16
Clean outring and disc with three SS screw as a clean out,
Supply Nos. 3.00 0.00

Fixing Nos. 3.00 0.00

TOTAL FOR SANITARY FIXTURES & FITTINGS 0.00

II SOIL, WASTE, RAINWATER AND VENT PIPE SYSTEM

Supplying, laying, jointing, testing and commission-ing approved make UPVC pipes
6 Kg/cm2 with solvent cement joints confirming to IS 4985 for wash basin outlets &
17 AC drain pipes Pipes.The quoted rate shall include necessary chasing in walls
making good the same in C.M. 1:4, necessary fittings viz.,elbows, tees etc., with G.I
clamps. Anchor fasteners, Grip bolts, nuts and bolts, etc,complete.

a) 25 mm Outer dia ( For AC drain pipe ) Rmt 25.00 0.00

b) 40 mm Outer dia ( For WB to PT ) Rmt 45.00 0.00
c) 50 mm Outer dia (For pantry sink bottle trap to FT ) Rmt 15.00 0.00
Supplying, laying, jointing, testing and commission-ing approved make UPVC pipes
4 Kg/cm2 with solvent cement joints confirming to IS 4985 for vent pipes Pipes.The
18 quoted rate shall include necessary chasing in walls making good the same in C.M.
1:4, necessary fittings viz.,elbows, tees etc., with G.I clamps. Anchor fasteners,
Grip bolts, nuts and bolts, etc,complete.
a) 63 mm Outer dia ( 4 kg/cm2)- ASP Rmt 15.00 0.00
Supplying, fixing and testing uPVC soil, waste and vent pipes (SWR) confirming to
IS13592 :1992, type B with rubber ring (confirming IS:5382) joint for inside the
toilet, hand wash area & inside the shaft inclusive of all necessary specials like
19
bends, tees, offsets, door ends, junctions, cowls, etc., laid under floor/fixed on
walls,and in pipe shafts etc., complete.The quoted rate should include necessary
MS supports like hanger supports, grip bolts and clamps etc.,
a) 75 mm Outer dia Rmt 90.00 0.00
b) 110 mm Outer dia Rmt 155.00 0.00

Supplying, fixing and testing uPVC soil, waste and vent pipes (SWR) confirming to
IS13592 :1992, type B with rubber ring (confirming IS:5382) joint for rain water
pipes at terrace & balcony area inclusive of all necessary specials like bends, tees,
20
offsets, door ends, junctions, cowls, etc., laid under floor/fixed on walls,and in pipe
shafts etc., complete.The quoted rate should include necessary MS supports like
hanger supports, grip bolts and clamps etc.,

a) 75 mm Outer dia Rmt 15.00 0.00

b) 110 mm Outer dia Rmt 60.00 0.00
c) 160 mm Outer dia Rmt 30.00 0.00
Supplying and fixing of approved make CI roof corner outlets for rainwater outlets
21
on terrace, complete. As shown in the Drawing.
a) 75 mm ( For Staircase & lift lobby Roof Level ) Nos. 2.00 0.00
b) 110 mm( For terrace Level ) Nos. 6.00 0.00

Supplying and fixing approved make 110mmx110mm dia PVC 'Q' trap with bose
pipe arrangements & and slotted type floor grating bronze chrome plated ring and
22
grate with two SS screw with necessary pipe support fixed below or above slab with
GI suspenders. ( For Toilets)

NOTE: THE PVC EXTENTION PIPE FOR TOILET FLOOR TRAPS EXTENSION
PIPE LENGTH SHOULD BE 150MM ABOVE THE SUNKEN SLAB & 500MM Nos. 22.00 0.00
FROM BOTTOM OF THE SLAB

Supplying and fixing approved make Deap Seal UPVC multi-inlet with minimum
50mm water seal floor trap with 75 mm dia outlet with and slotted type floor grating
23
bronze chrome plated ring and grate with two SS screw with necessary pipe
support fixed below or above slab with GI suspenders. ( For Pantry)

NOTE: THE PVC EXTENTION PIPE FOR KITCHEN FLOOR TRAPS EXTENSION
Nos. 6.00 0.00
PIPE LENGTH SHOULD BE 150MM ABOVE THE SUNKEN SLAB.
Sl No Description Unit Quantity Rate Amount
Rs. Rs.
Supplying, installing, testing and commissioning of approved make Centrifugally
Cast Iron pipes & fittings confirming to IS 3989 - 1984 with necessary fittings like
24 bends, tee's, plugs, etc., with necessary jointing by joint seal laid under floor, wall
etc., complete. The quoted rate shall include necessary pipe supports like pipe
hangers, MS brackets etc.,( for Kitchen waste)
a) 75 mm Outer dia Rmt 30.00 0.00
b) 100 mm Outer dia Rmt 25.00 0.00
c) 150 mm Outer dia Rmt 75.00 0.00
Supplying, fixing and testing of floor drain with 100mm dia CI 'P' trap with floor
25 grating of Neer make - model NRG 7004, bronze chrome plated ring and grate with Nos. 12.00 0.00
two SS screw etc., complete.

Drilling with core cutting machine in RCC slabs/Beams, floors etc., for Laying pipes
and rendering the same in RCC 1:2:4, finishing the same to the satisfaction of the
26 owner or his authorized representative etc., including nominal reinforcement
wherever required complete. The quoted rate shall also include for providing
EPOXY based water proofing compound for sealing the joints around the pipes.

a) For EWC 110mm dia pipes Nos. 10.00 0.00

b) For Floor Drain 110mm dia floor trap pipes Nos. 12.00 0.00
c) For Floor Trap 50/40 mm dia pipes Nos. 5.00 0.00
Construction of inspection chamber with 230mm best quality approved Table
Moulded bricks in CM 1:4 over a bed of 100mm thick PCC 1:4:8, internal walls
plastered in CM 1:3 and external wall with CM 1:6 with sponge finish, benching
27 and channelling in PCC 1:3:6. Supplying and fixing RCC square frame & cover of No. 8.00 0.00
size 600 x 600mm (medium duty) as per the detailed drawing. The quoted rate shall
also include necessary excavation and internal size of the chamber 600 x 600mm
maximum depth not exceeding 1200mm.

Construction of man hole with best quality, approved table moulded bricks in CM
1:6, 500mm dia @ top and 1200mm dia. @ bottom over a bed of 250mm thick PCC
1:4:8, walls plastered smooth inside in CM 1:3 and outside with CM 1:6 with sponge
finish benching and channelling in PCC 1:3:6 supplying & fixing PVC steps as per
28 No. 5.00 0.00
drawing for maintenance. The manhole shall be provided with heavy duty RCC
frame & cover. Circular 550 mm dia. Clear opening etc., complete. The quoted rate
shall also include for necessary pvc steps, excavation, refilling, disposing off
surplus earth with in a lead of 300M etc., complete. Depth upto 2.5 Mtrs.

Supplying, fixing, testing and commissioning approved make upvc deep seal P
traps with 110mm dia outlet connected to inspection chambers, 150x150mm C.I.
29 grating (medium duty), PCC 1:4:8 bed, 115 thick masonry chamber in CM 1:4, No. 7.00 0.00
internal and external plastering 12mm thick in CM 1:6, necessary earthwork, C.I.
cover medium duty weighing 12Kgs. etc., complete.

Excavation in all types of soil for laying pipes upto 300mm dia. including forming
bottom surface to required level, refilling selected excavated earth around the pipe
30
in layers 150mm thick, watering, consolidating and disposing off the surplus earth
with in the site as directed by the site engineer with a lead of 300M etc., complete.

Depth of excavation 0.0m to 2.0m Cum 250.00 0.00

Supplying, laying, jointing, testing and commission-ing approved make PVC Eco -
Drain structured pipes confirming to IS 15328 with SN4 rubber ring/Solvent Cement
31 joints for Soil Pipes laid on compacted filled soil below formed ground level. .The
quoted rate shall include necessary fittings like Tees, Bends, Offsets etc.,
complete.
a) 150 mm dia Rmt 120.00 0.00

Construction of catch basin for external storm water drainage with 230mm thick
walls in well burnt table moulded bricks in CM 1:4 over a bed of 100 mm thick PCC
1:4:8 internal walls plastered smooth in CM 1:3 and external walls plastered in1:6
32
with sponge finish. Providing and fixing FRP heavu duty grating of size as per
drawing on top surface flushed to the finished floor level with necessary excavation,
back filling the selected excavated earth with all leads and lifts etc., complete.

600x600x1.2 mm depth Nos. 7.00 0.00

Providing & constructing rain water recharge recharge pits as per the details given
33 in the drawing. The quoted rate shall include pre-cast RCC rings, top cover RCC Nos 4.00 0.00
slab, necessary excavation etc...complete as shown in the drawing.

34 Supplying, installing and testing of aco drain channels, sizes as per the drawing. Nos. 35.00 0.00
Sl No Description Unit Quantity Rate Amount
Rs. Rs.
Making Connection Of Drain Or Sewer Line, External Dia. With Existing Manhole
Including Breaking Into And Making Good The Walls, Floors With Cement Concrete
M15 With 20Mm And Down Size Granite Metal, Cement Plastered On Both Sides
Of Mix 1:3, Finished With A Floating Coat Of Neat Cement, And Making Necessary
35 Nos. 3.00 0.00
Channels For The Drain, Including Cost Of materials, Labour Charges, Curing
Complete As Per Specifications.
Dia. 100 To 230 mm

Making Connection Of Drain Or Sewer Line, External Dia. With Existing Manhole
Including Breaking Into And Making Good The Walls, Floors With Cement Concrete
M15 With 20Mm And Down Size Granite Metal, Cement Plastered On Both Sides
Of Mix 1:3, Finished With A Floating Coat Of Neat Cement, And Making Necessary
36 Nos. 5.00 0.00
Channels For The Drain, Including Cost Of Amterials, Labour Charges, Curing
Complete As Per Specifications.
Dia 350 To 450 mm

TOTAL FOR SOIL, WASTE, RAINWATER AND VENT PIPE SYSTEM 0.00
III WATER SUPPLY SYSTEM
Supplying, installing, fixing, jointing, testing and commissioning of approved make
Chlorinated Polyvinyl Chloride pipes & fittings (CPVC) SDR.11, The fittings and
specials such as tees, elbows, couplers, bends, enlargers etc, with CPVC brass
threaded combination / transition specials such as male adapters brass threaded
37 female adapters, brass FPT Tee, Brass FPT elbow etc., where connection with
metal is to be made including necessary drilling holes, chasing walls and making
the same good in cement martor 1:1 restore the same original condition neately as
directed by the Engineer in-charge. Joints to be made with CPVC solvent cement
up to 50mm dia as per ASTM D-2846.
a) 20 mm dia Rmt 60.00 0.00
b) 25 mm dia Rmt 75.00 0.00
c) 32 mm dia Rmt 60.00 0.00
d) 40 mm dia Rmt 30.00 0.00
e) 50 mm dia Rmt 55.00 0.00

Supplying, installing, testing and commissioning of approved make uPVC schedule

80 pipes and SCH-80 fittings conforming to ASTM D-1785. Quoted rate shall
38
include necessary fittings like, bends, elbows, reducers, collars, flanges, sadles,
adapters,clamps etc., and also including solvent for jonits. at ground level)

a) 40 OD mm dia Rmt 20.00 0.00

b) 50 OD mm dia Rmt 20.00 0.00
c) 65 OD mm dia Rmt 20.00 0.00
d) 80 OD mm dia Rmt 200.00 0.00

Supplying,Installing, testing & commissioning approved make Submersible Hydro-

pneumatic system comprising of horizontal Centrifugal pumps mounted on a
common skid with automatic control panel including over load relays, on-off push
39 button,switches, phase indicator lamps, dry run protection relays, pressure
Switches & guages, 1no. FRP pressure vessel of 1no.x 500Lts,Variable Frequency
Device mounted in one pump complete with cabling between thePumps &
controlpanel etc., complete. Thepumps shall runon 440V, 3ph, 50Hz electricsupply.

( Domestic water H.P.Pumps )

Duty of each pump : 15.0Cum/Hr @ 50.0m Head each pump
cut - in pressure:- 4.0 Bars
cut - off pressure:- 5.0 Bars
1 Nos. Working + 1 No.stand by = 1Set(2 pump series) Set. 1.00 0.00

Supplying, installing, testing and commissioning approved make G.M. body ball
40
valves PN12 , IS 1703-1977 with screwed ends,necessary unions etc., complete.

a) 25 mm dia Nos. 4.00 0.00

b) 32 mm dia Nos. 10.00 0.00
c) 40 mm dia Nos. 4.00 0.00
d) 50 mm dia Nos. 4.00 0.00
Supplying and fixing MSbrackets, hangers, supports with necessary drilling holes to
suit the insertion of pipe clamps,deburring etc., as per detailed drawing for
supporting water supply pipes at terrace with suitable MS clamps, bolts, anchor
41 Kgs. 10.00 0.00
bolts, nuts and washers fixed etc.The quoted rate shall include with the cost of
brackets galvanizing with zinc alloy of 0.08mm thick conformed to IS 1239
etc.,complete as directed by the employer.
Supplying, installing, testing and commissioning approved make mechanically
42
operated valve to be fixed in the OHT.
a) 50 mm dia Nos. 1.00 0.00
Sl No Description Unit Quantity Rate Amount
Rs. Rs.
Supplying and providing PCC 1:3:6 Support Pedestals below water Supply Pipe
43 lines with M.S brackets clamps, etc complete (in the terrace) [0.1cum of concrete Nos. 30.00 0.00
and bracket weight of 1.5 kgs in each Pedestal]
Supplying, fixing and testing inlet, outlet, vent and overflow pipes, fittings with FRP
44 frame and cover to Under ground sump complete with PVC Rungs as shown on the
drawings etc., complete, accessories comprising of the following
Approx. depth = 4.0Mts.
i) FRP manhole frame and cover (Heavy duty ) with locking facility Nos. 5.00 0.00
ii) Inlet puddle flanges -
100mm dia Nos. 2.00 0.00
80mm dia Nos. 2.00 0.00
65mm dia Nos. 2.00 0.00

iii) Outlet puddle flanges - 100mm dia Nos. 4.00 0.00

80mm dia Nos. 2.00 0.00
65mm dia. Nos. 2.00 0.00
iv) Vent pipe with mosquito proof mesh (100mm dia) Nos. 5.00 0.00
v)Sleeves for level controller - 50mm dia Nos. 2.00 0.00
v)Heavy duty pvc rungs - 165x375mm Nos. 25.00 0.00
Note : All puddle flanges to be hot dip galvanised.

Supplying, Installing, Testing and Commissioning of Pressure reducing valves of

bronze body, food grade rubber diaphragm, with double female ends, pressure
45
adjusting screw head, pressure gauge connections on both sides of the valves etc,
complete. The quoted rate shall also include for 2 nos. pressure gauge.

a) 65 mm dia Nos. 3.00 0.00

Supplying,installing and commisioning PN16 SS Expansion Bellows with SS
46 braiding & MS flanges for Suction and delivery headers including all necessary
supports, neoprine rubber gaskets, nuts, bolts etc., complete.
a) 100mm dia Nos. 2.00 0.00
b) 80mm dia Nos. 2.00 0.00
Supplying, installing, testing and commissioning CI butterfly valves (PN16) with
47 standard lever confirming to IS standard 13039 with necessary flanges, nuts and
bolts etc., complete.
a) 80mm dia Nos. 4.00 0.00
b) 65mm dia Nos. 6.00 0.00
c) 50mm dia Nos. 6.00 0.00
Supplying, fixing and testing approved make C.I check valve slim seal PN 16, IS
48 5312-1969 with necessary flanges, nuts, bolts & Neoprene Rubber gaskets etc.,
complete confirming to API/BIS.
a) 80mm nominal dia Nos. 4.00 0.00
Supplying, installing, testing and commissioningapproved makeANSI Class
49 125/150 Cast Iron body brass 'Y' strainer withnecessary flanges, nuts & bolts
Noeprine Rubber Gaskets etc.,completeon to the suction line.(PN16)
a) 80mm nominal dia Nos. 1.00 0.00
Supplying, installing and testing of 100mm dia tanker inlet connection system near
50 the raw water storage tank.this includes 100 dia standpost, non return valve, Nos. 1.00 0.00
Butterfly Valve etc.,complete

Making Connection Of Gi Distribution Branchwith Gi Main Of 50 To 85 Mm And

100 To 150 Nominal Bore, Including Cutting And Threading The Pipes, Providing
51 Nos. 3.00 0.00
And Fixing Tee, Nuts, Labour For All Item Of Works, Testing And Hom Complete
As Per Specifications.

TOTAL FOR WATER SUPPLY SYSTEM 0.00

IV HOT WATER SUPPLY SYSTEM

Supply, Installation, testing and commissionig of Solar Hybrid system (Combination

of Solar and Heat Pump) with reference to the following specifications. The quoted
52 rate shall be inclusive of solar collectors, Collector frame and support as required,
All in One heat pump, circulation pumps, solar and heat pump controller with
necessary plumbing, including valves, safety devises, insulation, fittings etc.

Solar system
53 Nos. 1.00 0.00
500 Litres spring tank with & 3.5 kw Each ( 2 working) heat pump
PLUMBING, INSTALLATION AND COMMISSIONING
Sl No Description Unit Quantity Rate Amount
Rs. Rs.
Plumbing, Installation & Commissioning
Cost for Plumbing, installation, labour & commissioning. Plumbing, duly insulated
with Nitrile Rubber between Storage tank and Solar collectors will be done in
MS/GI , between heat pumps and solar tank in CPVC complete with accessories,
54 Job 1.00 0.00
fittings, safety devises, etc.
Note -
1. The location of the equipment should be frozen
2. The battery limit for plumbing works will be clearly indicated in schematic.
TOTAL FOR HOT WATER SUPPLY SYSTEM 0.00
V RE-ROUTING WORKS

Construction of man hole with best quality, approved table moulded bricks in CM
1:6, 500mm dia @ top and 1200mm dia. @ bottom over a bed of 250mm thick PCC
1:4:8, walls plastered smooth inside in CM 1:3 and outside with CM 1:6 with sponge
finish benching and channelling in PCC 1:3:6 supplying & fixing PVC steps as per
55 Nos. 13.00 0.00
drawing for maintenance. The manhole shall be provided with heavy duty FRP
cover. Circular 550 mm dia. Clear opening etc., complete. The quoted rate shall
also include for necessary pvc steps, excavation, refilling, disposing off surplus
earth with in a lead of 300M etc., complete. Depth upto 2.25 Mtrs.

Construction of catch basin for external storm water drainage with 230mm thick
walls in well burnt table moulded bricks in CM 1:4 over a bed of 100 mm thick PCC
1:4:8 internal walls plastered smooth in CM 1:3 and external walls plastered in1:6
with sponge finish. Providing and fixing FRP heavu duty grating of size as per
56 drawing on top surface flushed to the finished floor level with necessary excavation,
back filling the selected excavated earth with all leads and lifts etc., complete. The
quoted rate shall include 110dia PVC pipe sleeves with filter media from road GSM
to the chamber and also providing and fixing GI grating for the inlet from the road to
the catch basin as shown in the drawings.
600x600x750mm depth Nos. 1.00 0.00
Supplying, laying, jointing, testing and commissioning approved make DWC SN4
pipes SN4 rubber ring/Solvent Cement joints for External sewage/storm water
57
system laid below ground level. The quoted rate shall include necessary fittings like
Tees,Bends, Offsets etc., complete.
a) 160 mm dia Rmt 145.00 0.00
b) 200 mm dia Rmt 16.00 0.00
c) 250 mm dia Rmt 145.00 0.00
Supplying, Laying, jointing, testing and commissioning make class K9 Ductile Iron
pipes & fittings with 5mm thick cement lining inside and bituminous coating outside
confirming to IS8329 & BS 4772 class K12 with Tyton joints for External water
58
supply mains.The quoted rates shall also include cost of Rubber rings confirming to
IS 5382, Necessary supports as required etc.,complete laid in trenches as per
standards and as shown in the drawing.
a) 100 mm dia Rmt 120.00 0.00

Excavation in all types of soil for laying pipes upto 450mm dia. including forming
bottom surface to required level, refilling selected excavated earth around the pipe
59
in layers 150mm thick, watering, consolidating and disposing off the surplus earth
with in the site as directed by the site engineer with a lead of 300M etc., complete.

Depth of excavation 0.75m to 2.0m Cum 450.00 0.00

Providing & Constructing Valve chamber of 0.6x0.6x0.8m BBM with CM 1:6,
60 internal walls plastered in CM 1:3 & external walls plastered in CM 1:6, FRP heavy No. 2.00 0.00
duty manhole cover of 600x600 in size etc., complete for the following.
Supplying, installing, testing and commissioning CI butterfly valves (PN - 16) with
61 standard lever confirming to IS standard 13039 with necessary flanges, nuts and
bolts etc., complete.

a) 100mm dia Nos. 4.00 0.00

Making Connection Of Drain Or Sewer Line, External Dia. With Existing Manhole
Including Breaking Into And Making Good The Walls, Floors With Cement Concrete
M15 With 20Mm And Down Size Granite Metal, Cement Plastered On Both Sides
Of Mix 1:3, Finished With A Floating Coat Of Neat Cement, And Making Necessary
62 Nos. 2.00 0.00
Channels For The Drain, Including Cost Of Amterials, Labour Charges, Curing
Complete As Per Specifications.
Dia. 100 To 230 Mm
Sl No Description Unit Quantity Rate Amount
Rs. Rs.

Making Connection Of Drain Or Sewer Line, External Dia. With Existing Manhole
Including Breaking Into And Making Good The Walls, Floors With Cement Concrete
M15 With 20Mm And Down Size Granite Metal, Cement Plastered On Both Sides
63 Of Mix 1:3, Finished With A Floating Coat Of Neat Cement, And Making Necessary Nos. 3.00 0.00
Channels For The Drain, Including Cost Of Amterials, Labour Charges, Curing
Complete As Per Specifications.
Dia 350 To 450 mm

Making Connection Of Gi Distribution Branchwith Gi Main Of 50 To 85 Mm And

100 To 150 Nominal Bore, Including Cutting And Threading The Pipes, Providing
64 Nos. 2.00 0.00
And Fixing Tee, Nuts, Labour For All Item Of Works, Testing And Hom Complete
As Per Specifications.

TOTAL FOR RE-ROUTING WORKS 0.00

 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR SUPPLY AND INSTALLATION OF LIFT EQUIPMENTS FOR FOR CONSTRUCTION OF
DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

Sl.No DESCRIPTION Amount

Rs.

I PASSENGER LIFT 0.00

II GOODS LIFT 0.00

GRAND TOTAL 0.00

GST, EXTRA AS APPLICABLE
 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR SUPPLY AND INSTALLATION OF LIFT EQUIPMENTS FOR FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

Sl No. Description Unit Quantity Rate Amount

Rs. Rs.
I LIFT EQUIPMENT

Design, Supply, errecting, testing and commissioning of - Passenger lift capacity 10 Passengers with speed of
1 metre per second, variable voltage, variable frequency drive, with or without machine room for the available
well size operating at 415 V 3 phase 50 (Hz) cycles AC Supply, powder coated/Stainless Steel Car entrance
Door enclosures with suitable colour vinyl flooring, LED car illumination, emergency light, intercom and fan as
desired by the User,Central opening/side opening door with or without attendant operation, 7 segment display
buttons, callregister indicator, fireman drive, SS handrails inside car, full length infrared curtain in car door,
automatic rescue device with batteries, voice announcing in regional/international languages. Braille buttons
with one year warranty and maintenance with necessary scaffolding and minor civil works like fixing of guide
1 Nos 1.00 0.00
rail, counter weight, etc. The total product and sevices shall adhere to IS 14665/2016 (with latest
ammendments) part/section 1 to 5 with regards to general guidelines of fire and safety rated doors, MRLL
beams, pressure switch, manual change over for doors during emergency,ARD of 10 times with sufficient
battery back up and standard dimensions of chair car and door openings for all sizes and capacities of lifts
including fitness certificate and duly observing of all other safety norms prescribed and adhere to CPWD
Specifications, PCB norms, National Electricity Code (NEC), NBC 2016, IEC and Karnataka State Lifts,
Escalators and Passengers COnveyors Act 2012 and Rules 2014. The Supplier shall be registered in
Government Electrical Inspectorate in the State of Karnataka.
Design, Supply, errecting, testing and commissioning of - Goods lift (or capacity 15 Passengers) with speed
of 1 metre per second, variable voltage, variable frequency drive, with or without machine room for the
available well size operating at 415 V 3 phase 50 (Hz) cycles AC Supply, powder coated/Stainless Steel Car
entrance Door enclosures with suitable colour vinyl flooring, LED car illumination, emergency light, intercom
and fan as desired by the User,Central opening/side opening door with or without attendant operation, 7
segment display buttons, callregister indicator, fireman drive, SS handrails inside car, full length infrared curtain
in car door, automatic rescue device with batteries, voice announcing in regional/international languages.
Braille buttons with one year warranty and maintenance with necessary scaffolding and minor civil works like
2 Nos 1.00 0.00
fixing of guide rail, counter weight, etc. The total product and sevices shall adhere to IS 14665/2016 (with latest
ammendments) part/section 1 to 5 with regards to general guidelines of fire and safety rated doors, MRLL
beams, pressure switch, manual change over for doors during emergency,ARD of 10 times with sufficient
battery back up and standard dimensions of chair car and door openings for all sizes and capacities of lifts
including fitness certificate and duly observing of all other safety norms prescribed and adhere to CPWD
Specifications, PCB norms, National Electricity Code (NEC), NBC 2016, IEC and Karnataka State Lifts,
Escalators and Passengers COnveyors Act 2012 and Rules 2014. The Supplier shall be registered in
Government Electrical Inspectorate in the State of Karnataka.
TOTAL 0.00
NOTE :
1. NECESSARY ARCHITECTURAL TENDER DRAWING TO BE READ IN CONJUNCTION WITH THE
ABOVE SPECIFICATIONS.
2. THE RATE IS INCLUSIVE OF ALL NECESSARY SCAFFOLDING AND NECESSARY ASSOCIATED
CIVIL WORKS AS REQUIRED FOR ERRECTION OF THE LIFTS.
3. ALL NECESSARY STATUTORY PERMISSIONS FROM THE LOCAL AUTHORITIES LIKE PCB,
ELECTRICAL INSPECTOR, LIFT INSPECTOR, ANY OTHER STATUTORY CLEARANCE ETC TO BE
OBTAINED BY THE VENDOR BEFORE HANDING OVER OF THE LIFTS TO THE DEPARTMENT
4. THE LIFTS TO BE OF APPROVED MAKES - JOHNSON, OTIS, KONE. THE VENDOR TO NOTIFY THE
EIC BEFORE PROCUREMENT OF LIFTS.
GST extra as applicable
 M/s. Indian Institute of Management, Bangalore
ABSTRACT ESTIMATE FOR ELECTRICAL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN
HOSTEL MESS AND NIGHT CANTEEN
Amount
Sl No Description
Supply- Rs. Installation- Rs.

A MV Panel 0.00 0.00

B INTERNAL ELECTRICAL WORKS 0.00 0.00

C LIGHT FIXTURES 0.00 0.00

D FANS 0.00 0.00

E CABLES & TRAYS 0.00 0.00

F EARTHING 0.00 0.00

G WIFI 0.00 0.00

H TV 0.00 0.00

TOTAL 0.00 0.00

GRAND TOTAL 0.00
GST, EXTRA AS APPLICABLE
 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR ELECTRICAL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

Rate Amount
S No Description Unit Quantity
Supply Instln Supply Instln

A MV Panels
Supply,Installation, Testing and Commissioning of 3 phase 415V 4 wire Free
Standing Floor mounted MV panel made out of 14 SWG CRCA sheet after nine
tank process and painting with Epoxy powder coating including all switchgear as
detailed below and Panels shall be Indoor/Outdoor type front operated cubicle
type compartmentalised as per IEC 60439(Part-1&2). The panel shall consist of
suitable rating TPN Aluminum-bus bar (at the rating of 0.8ASq.mm) supported
with DMC/SMC barriers and color coded with Heat shrinkable sleeves. The
Metering shall be provided as specified. The panel shall have Short circuit with
standing capacity of minimum 50KA and consist of the switchgear as mentioned
below. The panel shall be mounted on channels grouted to the floor including all
materials. The panel shall be got fabricated from manufacturers with CPRI Test
certificate only. All the PCC/ Panels shall have at least two spare cubicles of the
maximum rating. All feeders shall be earthed with 2 GS flats of adequate size to
the main earth bus of 50x6mm GS flat. The size of all Panel Mounting Meters shall
be 96X96mm.The Panels shall be mounted on U channels including supply and
fixing of the same. Fuses shall be provided for Control purposes (All Panels shall
be extendable type only) Maximum height of the panel shall be considered up to
1875/2100mm only.

Every ACB shall be provided with ON/OFF /Trip Indication lamps of LED type and
Auto/Manual Selector Switches. All MCCBs shall provide with spreader links and
rotary handle. Incomer Breakers of all panels shall have required NO+NC Auxiliary
contacts for BMS ON,OFF,TRIP Status & Control and all the Control.Thermal
magnetic type MCCBs Shall be provided up to 200A rating & Above 200A MCCB
shall be Provided with Microprocessor Based Type O/C,S/C&E/F releases, All CTs
are shall be provided with Resin Cast type.

Panels Shall be Type Tested Switchgear Assembly conforming to IEC 60439-1/2

and IEC 61641, Makes of the switch gear shall be followed as per recommened
Makes of materials specied in attached Technical Specifications

The tenderer / switchgear supplier shall provide releases and trip units to ensure
discrimination of entire system from downstream MCB in final Distribution Boards
to upstream main LT panel ACB's as per schematic drawings.

AS PER SLD
1 Main Panel No 1.00 0.00 0.00
2 HVAC Panel No 1.00 0.00 0.00

3 Lift Panel No 2.00 0.00 0.00

TOTAL FOR MV PANELS 0.00 0.00

B INTERNAL ELECTRIFICATION

Any Opening to be done in RCC wall, slab and beams shall be done by core
cutting machine in consultation with structural consultants / The Employer.

The Point wiring shall include the following

a) Wiring from Switch Control to Light/ Fan/ Socket outlet. All b) 16A Switches
shall be with built-in indicators.
c) Chasing in the wall and fixing of conduit with saddles and spacers, wire-mesh
and making them good..
d) Painting of all metallic boxes with approved shade of paint after Red oxide
primer wherever MS boxes are specified.
e) Supply and fixing of Anodized GI switch boxes of suitable size with front plate
and switches/sockets.
f) All wires equal to or above 4 sq.mm shall be terminated with copper pin type
*
lugs including crimping.
g) Flexible hose need to consider from ceiling rose to light fixture & Ferruling to be
done at both switch board terminal & light terminal
h) The quoted rate shall be inclusive of required switches, sockets, regulators,
blank plates, front plates, switchboard & other accessories deemed to be
necessary as per technical specifications, IS standards & drawing details
Complete.
i) Necessary flexible pipe to be consider in the quoted price

1 CONDUITING
Supply and laying of Dia, 2mm,thick FRLS Heavy Duty PVC Conduit
concealed in wall/ Surface mounted on ceiling/floor/ column including supply and
drawing of 12SWG GI wire as fish wire for pulling of wires at a later stage and the
rate shall includes all necessary fixing materials complete as required. Conduit
length only
1.a 19mm Mtrs 200.00 0.00 0.00
 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR ELECTRICAL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

Rate Amount
S No Description Unit Quantity
Supply Instln Supply Instln
1.b 25mm Mtrs 5000.00 0.00 0.00

1.c 32mm Mtrs 200.00 0.00 0.00

2 WIRING

Supply and laying of 660V/1100V PVC insulated FRLS grade as per IS-694 (with
latest amendments) with ISI Mark, multi strand Copper conductor wires in 25mm
dia heavy gauge FRLS PVC conduit concealed in wall/Surface mounted on
Ceiling/ raceways. ( Rate shall be exclusive of Conduit ).

2.a 3Rx4sqmm Mtrs 2400.00 0.00 0.00

2.b 3Rx 2.5sqmm Mtrs 720.00 0.00 0.00

2.c 3Rx2.5sqmm Mtrs 1200.00 0.00 0.00

RACEWAYS
3
Supply and laying of 1.6mm Thick GI Raceways of the following sizes suspended
from Ceiling/ fixing to wall, the rate shall includes all necessary fixing accessories
viz., Threaded Rod, Slotted Channel etc complete as required. Earth wire of 16
SWG size GI wire shall be run all along the raceways for body earthing.
(Bifurcated for Power & ELV, if required)
3.a
100x50mm 1.6mm thick GI Race way Mtrs 50.00 0.00 0.00
3.b
75x50mm 1.6mm thick GI Race way Mtrs 50.00 0.00 0.00
3.c
Junction Box suitable for item 3.a Nos 2.00 0.00 0.00
3.d
Junction Box suitable for item 3.b Nos 2.00 0.00 0.00

4 Flexible Multistrand Copper Cable

4.a Supply and laying of 3C x 2.5 sq.mm, multistrand, Copper flexible cable. Mtrs 150.00 0.00 0.00

4.b Supply and laying of 3C x 1.5 sq.mm, multistrand, Copper flexible cable. Mtrs 100.00 0.00 0.00

Supply and fixing surface / flushmounting unbreakable PVC modular box suitable
for mounting switch plates with due groove cutting in Brick / CC wall , including
5
necessary rawl plugs, machine screws / NF screws etc. complete., with rough
plastering
5.a 1-2 Module Nos 2.00 0.00 0.00

5.b 3 Module Nos 2.00 0.00 0.00

5.c 4 Module Nos 2.00 0.00 0.00

5.d 6 Module Nos 2.00 0.00 0.00

5.e 8 Module Nos 2.00 0.00 0.00

Supply and fixing surface / flush mounting coated / galvanized metal box
suitable for mounting switch plates with due groove cutting in Brick / CC wall ,
6
including necessary rawl plugs, machine screws / NF screws etc. complete., with
rough plastering
6.a 1-3 Module Nos 96.00 0.00 0.00

6.b 4 Module Nos 13.00 0.00 0.00

6.c 6 Module Nos 14.00 0.00 0.00

6.d 8 Module Nos 5.00 0.00 0.00

6.e 9 Module Nos 2.00 0.00 0.00

6.f 10-12 Module Nos 13.00 0.00 0.00

6.g 16 Module Nos 6.00 0.00 0.00

Supplying and fixing of Modular Cover Plates with frame of required sizes
7
wherever necessary.
7.a 1 Module plate + Frame Nos 16.00 0.00 0.00

7.b 2 Module plate + Frame Nos 12.00 0.00 0.00

7.c 3 Module plate + Frame Nos 71.00 0.00 0.00

7.d 4 Module plate + Frame Nos 13.00 0.00 0.00

7.e 6 Module plate + Frame Nos 14.00 0.00 0.00

7.f 8 Module plate + Frame ( Hz) Nos 2.00 0.00 0.00

 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR ELECTRICAL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

Rate Amount
S No Description Unit Quantity
Supply Instln Supply Instln
7.g 8 Module plate + Frame ( 4x2) Nos 2.00 0.00 0.00

7.h 12 Module plate + Frame Nos 12.00 0.00 0.00

7.i 16 Module plate + Frame Nos 6.00 0.00 0.00

Supply and fixing of modular switch / socket / stepped electronic fan regulator etc
8
on existing modular switch plate as per IS 3854 and IS 1293.
8.a 6A One way switch Nos 121.00 0.00 0.00

8.b 6A Two way switch Nos 2.00 0.00 0.00

8.c 16A Switch with Indicator Nos 104.00 0.00 0.00

8.d 6A Exhaust Fan Universal Socket-2M with 5 pin Nos 7.00 0.00 0.00
2 Nos 6A universal Sockets with safety shutters . Colour of the switch plate shall
8.e Nos 25.00 0.00 0.00
be White

1 No 6A universal Socket & safety shutters Colour of the switch plate shall be
8.f White (This socket switch point located outside of toilet controlled by single switch Nos 7.00 0.00 0.00
only in toilet area)

1 No. 6/16A, Plate socket with safety shutters. Colour of the switch plate shall be
8.g Nos 16.00 0.00 0.00
White

1 No. 25A, Plate switch 3 pin socket with safety shutters controlled by One 25A
8.h Nos 3.00 0.00 0.00
DP 1W switch for kitchen equipment. Colour of the switch plate shall be White

16A Industrial 1phase 3 pin sockets for Outdoor Application/Kitchen with Interlock
8.i Nos 10.00 0.00 0.00
IP55 with plug top

32A Industrial 1phase 3 pin sockets for Outdoor Application/Kitchen with Interlock
8.j Nos 10.00 0.00 0.00
IP55 with plug top.

8.k Stepped Fan Regulator Nos 49.00 0.00 0.00

8.l 1M Blank Plate Nos 50.00 0.00 0.00

9 POINT WIRING

Light Points (Switch Control) : Supply and wiring for light point with 3 runs of 2.5
sq.mm, 660V/1100V PVC insulated FRLS grade as per IS-694, Copper conductor
multistrand wires in 25mm dia heavy gauge FRLS PVC conduit concealed in wall/
Ceiling including including supply of all fixing materials, accessories and
interconnections complete as required. The light point shall be control from Switch
to Light points.

9.1 For Primary Points. Ie., Measurement shall be From Switch to First Light Point

.a upto 3mtrs Nos 4.00 0.00 0.00

b 3mtrs to 6mtrs Nos 6.00 0.00 0.00

c 6mtrs to 9 mtrs Nos 20.00 0.00 0.00

d 9mtrs to 12 mtrs Nos 13.00 0.00 0.00

e 12mtrs to 15mtrs Nos 2.00 0.00 0.00

f 15mtrs to 19mtrs Nos 2.00 0.00 0.00

9.2 For SecondaryPoints/ Looping of Light points

a 3mtrs to 6mtrs Nos 30.00 0.00 0.00

b 6mtrs to 9 mtrs Nos 62.00 0.00 0.00

c 9mtrs to 12 mtrs Nos 73.00 0.00 0.00

d 12mtrs to 15mtrs Nos 2.00 0.00 0.00

9.3 For Fan Points From Regulato to Fan Point

a upto 6mtrs Nos 2.00 0.00 0.00

 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR ELECTRICAL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

Rate Amount
S No Description Unit Quantity
Supply Instln Supply Instln
b 6mtrs to 9 mtrs Nos 2.00 0.00 0.00

c 9mtrs to 12 mtrs Nos 10.00 0.00 0.00

d 12mtrs to 15mtrs Nos 6.00 0.00 0.00

e 15mtrs to 18 mtrs Nos 14.00 0.00 0.00

f 18mtrs to 21 mtrs Nos 14.00 0.00 0.00

g 21mtrs to 24 mtrs Nos 2.00 0.00 0.00

h 24mtrs to 27 mtrs Nos 4.00 0.00 0.00

i 27mtrs to 30 mtrs Nos 2.00 0.00 0.00

j 30mtrs to 33 mtrs Nos 4.00 0.00 0.00

k 33mtrs to 36 mtrs Nos 2.00 0.00 0.00

10 Supply and Laying Flexible Pipe wherever required

10.a 25mm mtrs 200.00 0.00 0.00

11 DISTRIBUTION BOARDS:

Supply Installation Testing and commissioning of TPN MCB Double door

Distribution boards dust and vermin protected and rated for 415V Three Phase
AC supply operation including incoming MCB/ELCB/RCCB as per specifications
and required capacity Neutral bar and Earth terminal complete as required and
installed in flush with wall including all fixing materials required the MS Powder
coated trunk with cover of suitable size and made of 14SWG Size around the
DB's shall be included. MCBs shall conform to IS: 8828 and ELCB/RCCB shall
conform to IS :12640. Lighting MCBs shall be 'C' Curve , Raw Power MCBs
shall be 'C' Curve & UPS Power MCBs shall be 'D' Curve. Necessary
trunking for Cable management to be consider for interconnecting the
ceiling race way to the respective DB.

8 way ETPNMCB DB
INCOMER:40A 10kA TPN MCB
SUB INCOMER:
11.a Sets 2.00 0.00 0.00
3 Nos of 30mA sensitivity 40A,10kA DP RCCB.
OUTGOINGS:
18nos 6A or 16A,10kA SPMCBs as outgoings
9 way ETPNMCB DB
INCOMER: 63 A 10kA TPN MCB
SUB INCOMER:
11.b Sets 2.00 0.00 0.00
3 Nos of 30mA sensitivity 63A,10kA DP RCCB.
OUTGOINGS:
18nos 6A or 16A,10kA SPMCBs as outgoings
12 way ETPNMCB DB (S-1 GND & 1st FLOOR LPDB)
INCOMER: 100 A 16kA TPN MCB
SUB INCOMER:
11.c Sets 1.00 0.00 0.00
3 Nos of 30mA sensitivity 100A,16kA DP RCCB.
OUTGOINGS:
30 nos 6A or 16A,10kA SPMCBs as outgoings
12
Charges for Chasing of walls for Conduiting Mtrs 75.00 0.00 0.00
13
Charges for Making Good of walls after Fixing of conduit with required mesh and
Mtrs 75.00 0.00 0.00
plaster.

14 LIFT SHAFT

Supply and wiring for socket with 3runs of 2.5sq.mm, 660V/1100V PVC insulated
FRLS grade as per IS-694 (with latest amendments) with ISI Mark, multi strand
Copper conductor wires in 25mm dia heavy gauge MS conduit concealed in
wall/Ceiling including supply and fixing of 6Amp Modular type switch in suitable
anodized GI box complete with front plate, supply and fixing 3way Ceiling rose or
straight/ slant batten holder including interconnections as required.
14.a 1 Nos of 6 A 5 Pin socket outlet with mounting box controlled by 6A switch
Set 2.00 0.00 0.00
including light point control by one 6A switch in every Floor level
15
ISOLATOR
15.a
16A TPN MCB ISOLATOR in Metal Enclosure for HVAC Nos 5.00 0.00 0.00
15.b
25A TPN MCB ISOLATOR in Metal Enclosure for Lifts Nos 2.00 0.00 0.00

15.c 32A TPN MCB ISOLATOR in Metal Enclosure Nos 1.00 0.00 0.00

15.d 63A TPN MCB ISOLATOR in Metal Enclosure Nos 1.00 0.00 0.00

16 Kitchen area Sockets

 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR ELECTRICAL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

Rate Amount
S No Description Unit Quantity
Supply Instln Supply Instln
Supply & Instllation of 16A 3P IP67 Industrial Interlocked Socket and straight Plug
confirming to IS/IEC 60309 1 and 2, The polycarbonate unit shall have socket
16.a mechanically interlocked with a switch so as to ensure plugging/Unplugging in live Nos 25.00 0.00 0.00
condition is avoided. The unit shall offer UV resistance. The unit shall Withstand
+100°C for 60 Min. Plugs shall confirm to IS/IEC 60309 1 and 2.
1 No. 6/16A, Plate socket with safety shutters. Colour of the switch plate shall be
16.b Nos 44.00 0.00 0.00
White
Supply of 125A 5P IP67 Industrial Interlocked Socket and straight Plug confirming
to IS/IEC 60309 1 and 2, The unit shall have socket mechanically interlocked with
16.c a switch so as to ensure plugging/Unplugging in live condition is avoided. The unit Nos 1.00 0.00 0.00
shall offer UV resistance. The unit shall Withstand +100°C for 60 Min. Plugs shall
confirm to IS/IEC 60309 1 and 2.
Supply of 32A 5P IP67 Industrial Interlocked Socket and straight Plug confirming
to IS/IEC 60309 1 and 2, The unit shall have socket mechanically interlocked with
16.d a switch so as to ensure plugging/Unplugging in live condition is avoided. The unit Nos 1.00 0.00 0.00
shall offer UV resistance. The unit shall Withstand +100°C for 60 Min. Plugs shall
confirm to IS/IEC 60309 1 and 2.
TOTAL INTERNAL ELECTRIFICATION 0.00 0.00

C LIGHT FIXTURES
16W LED Mirror Light Fixture,Wall Mounting type in toilets .
Surface mounted 2ft LED Batten Luminaire, for use in wash rooms above mirror,
made up of Aluminum extrusion housing with PC diffuser. Luminaire should be
with system efficacy of >120 Lumen/Watt, system wattage and minimum system
lumen output of 1600 lumens. The luminaire should have CRI>80 and CCT of
6500 K.The luminaire should be IP 20 protected. Luminaire should comply with all
1.1 Nos 6.00 0.00 0.00
the required IEC/BIS standards and should operate in a voltage range of 140 to
270 volts AC. Lifeclass of luminaire L70B50>50,000 hours with power factor >
0.95, THD<10%, surge protection of up to 4KV and ripple factor<5% for flicker free
operation. The luminaire and driver shall be from the same OEM and shall be BIS
approved and carry "R" number
.Make: Philips /Jaguar/Havells/ Lighting Technologies
18W LED Down Round Light Fixture,Surface Mounting Type.
Sleek Surface Down light fixture of 18W System Lumen-2000 Lm, Dimensions
Ø220mm X 26 mm ,Wattage 18W,Efficacy >110Lm/Watt, IngressProtection IP20,
CRI>80, CCT:6500K, Input Volatge: 130- 320V AC,Surge Protection 2KV,
1.2 PF>0.95, THD<15%. The entire is rated for a life class of L70B50 of 50000Burning Nos 173.00 0.00 0.00
Hours. Luminarie and Driver is from same OEM for a ease of spares and
serviciability and shall be BIS approved.
Make: Philips /Jaguar/Havells/ Lighting Technologies

22W LED Light Fixture,1200MM Surface mounted/ Suspended type in

Dining area
Pureline slim 22W LED Suspended 4feet length fixture with Extruded Aluminium
power coated body, PMMA Diffuser, IP20, CRI>80, PF>0.95, Efficacy:100
Lumens/Watt, Input Volatge: 130- 320V AC, Surge Protection 2.5KV Pf>0.95
1.3 THD<10%. Nos 173.00 0.00 0.00
The entire is rated for a life class of L70B50 of 50000Burning Hours. Luminarie
and Driver is from same OEM for a ease of spares and serviciability and shall be
BIS approved
Make: Philips /Jaguar/Havells/ Lighting Technologies

9W LED Bulk Head Light Fixture,Wall & Surface Mounting in Lifts.

IP66/IK09 rated with nominal 9W/600 lumen flux output, LED Bulk Head Light
Fixture for Wall & Surface Mounting in Lifts. Housing should be pressure die cast
1.4 aluminium with Polycarbonate front diffuser. The luminaire shall be BIS approved Nos 6.00 0.00 0.00
and carry the "R" number on the housing lable itself.
Make: Philips /Jaguar/Havells/ Lighting Technologies

4W STEP Light Fixture for steps.

Wall recessed 3W LED Step light with aluminium base material housing. The
luminaire should be IP 65 protected. Luminaire should comply with all the required
1.5 IEC/BIS standards and should operate in a voltage range of 220 to 240 volts AC. Nos 45.00 0.00 0.00
The luminaire and driver shall be from the same OEM and shall be BIS approved
and carry "R" number.
Make: Philips /Jaguar/Havells/ Lighting Technologies
Flood light fixtures Floor mounted type for open area terrace.
Supply of IP65/IK07 rated, 30W LED floodlight fixture made of aluminium pressure
die cast housing that would deliver at least 2600 lumen (4000K CCT) with an
1.6 efficacy of at least 85 lumen/watt. The driver shall have a 4KV surge protection, Nos 10.00 0.00 0.00
power factor of at least 0.9 and designed to operate at Ta of 45 deg C. The fixture
shall be BIS approved and carry "R" number for ease of spares and serviceability.
Make: Philips /Jaguar/Havells/ Lighting Technologies
 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR ELECTRICAL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

Rate Amount
S No Description Unit Quantity
Supply Instln Supply Instln
11W LED Down Light Fixture,Recessed Mounting type in common area
toilets .
Supply of recessed mounted circular LED Downlighter, made of Pressure Die Cast
Aluminum housing with PC diffuser. Luminaire should be with system efficacy of
>105 Lumen/Watt, system wattage of 11W and system lumen output of 1200lm.
1.7 The luminaire should have CRI>80 and CCT of 6500K. Luminaire should comply Nos 15.00 0.00 0.00
with all the required IEC/BIS standards and should operate in a voltage range of
140V - 270V AC. The luminaire and driver shall be from the same OEM and shall
be BIS approved and carry "R" number.
Make: Philips /Jaguar/Havells/ Lighting Technologies

TOTAL FOR LIGHT FIXTURES

0.00 0.00

D FANS
Ceiling Fan
Supply and installation of 1200mm Sweep Ceiling fan with down rod as required
1.1 including all accessories such as shackle, blades, wiring from ceiling rose to fan Nos 45.00 0.00 0.00
with 3core 1.5sq.mm cable but without regulator Crompton COOL BREEZE / Usha
/ Bajaj
Exhaust Fans
Supply and Installation of Exhaust fans of 200 mm sweep with gravity louvers
1.2 Nos 6.00 0.00 0.00
shutters including all accessories / Installation materials required.
Make : CGL BriskAirPlus/ Usha/Bajaj
0.00 0.00
TOTAL FOR FANS

E CABLES & TRAYS

MV Cables
Aluminium Cables
1
Supply, Laying and commissioning of following size 1.1KV grade XLPE insulated
for cables, sheathed steel strip/ wire armored aluminum conductor under ground
cable laying in cable trench/Cable tray/Hume pipes. The cable shall conform to
IS 7098/1554 with latest amendments.
3.5 core 240Sq.mm, Al. XLPE
1.1 Mtrs 65.00 0.00 0.00
4core 25 Sq.mm, Al. XLPE
1.2 Mtrs 65.00 0.00 0.00
4core 16.0sq.mm, Al. XLPE
1.3 Mtrs 30.00 0.00 0.00
4core 10.0sq.mm, Al. XLPE
1.4 Mtrs 72.00 0.00 0.00
4core 6.0sq.mm, Al. XLPE
1.5 Mtrs 360.00 0.00 0.00
3core 4sq.mm, Al. XLPE
1.6 Mtrs 50.00 0.00 0.00
Copper Cables
2
Supply, of following size 1.1KV grade XLPE insulated, FRLS, Armoured
multistrand copper conductor under ground, FR cable, in built up cable trench/
already laid RCC hume pipe or on cable tray with all installation materials. The
cable shall conform to IS 1554/Part I
2B 4Core, XLPE, FRLS, Armoured, Copper Cable
4core 4.0sq.mm
2.1 Mtrs 200.00 0.00 0.00
End terminations for Cables
3

Providing Indoor ordinary end terminations for the cable specified above with
compression type steel gland, Bi-metallic lugs using crimping tool, Insulation tape,
Identification tags etc., including end termination and Earthing of Gland.

3.5 core 240Sq.mm, Al. XLPE

3.1 Nos 2.00 0.00 0.00
4 core 25 Sq.mm, Al. XLPE
3.2 Nos 6.00 0.00 0.00
4 core 16 Sq.mm, Al. XLPE
3.3 Nos 2.00 0.00 0.00
4 core 10 Sq.mm, Al. XLPE
3.4 Nos 6.00 0.00 0.00
4 core 6 Sq.mm, Al. XLPE
3.5 Nos 16.00 0.00 0.00

4Core, XLPE, FRLS, Armoured, Copper Cable

4core 4.0sq.mm
3.6 Nos 24.00 0.00 0.00

CABLE TRAYS
4
Ladder GI Tray
 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR ELECTRICAL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

Rate Amount
S No Description Unit Quantity
Supply Instln Supply Instln

Supply, Design, Fabrication, Installation & Commissioning of of heavy duly

hot dipped galvanised (65 - 70 Micron as per IS 2629) Ladder type cable
trays of following sizes, suspended from ceiling or fixed vertically on wall / column
as per route directed at site, as approved complete as per technical specifications,
4.1 drawings & relevant standards & site conditions.
(Tray shall be made out of 2 / 2.5 mm thick sheet, standard length 2.5mtr GI
coupler plate2.5 mm thick with eight holes and 8 nos. 1 1/2' x 3/8 GI pasivated
nut bolts with 2 nos plain washers & GI clamp for tray fixing along with GI hard
ware.) -Trays.

Note:
1) Include site fabrication of required Bends, T-Junction, Elbows, X-Junction, Z-
Sections, Reducer etc.
2) Including of Cold galvanizing paint on welded spots.
4.1.1 225mmX50mm wide(25mmx6mm GI Strips) Mtrs 10.00 0.00 0.00

4.1.2 150mmX50mm wide(25mmx6mm GI Strips) Mtrs 10.00 0.00 0.00

4.1.3 100mmX50mm wide(25mmx6mm GI Strips) Mtrs 10.00 0.00 0.00

Perforated GI Tray

Supply, Design, Fabrication & Commissioning of heavy duly hot dipped

galvanised (65 - 70 Micron as per IS 2629) Perforated type cable trays with
Cover of following sizes, suspended from ceiling or fixed vertically on wall /
column with threaded rods/steel support as per route directed at site, as approved
complete as per technical specifications, drawings & relevant standards & site
4.2
conditions.
(Tray shall be made out of 2 / 2.5 mm thick sheet, standard length 2.5mtr GI
coupler plate2.5 mm thick with eight holes and 8 nos. 1 1/2' x 3/8 GI pasivated
nut bolts with 2 nos plain washers & GI clamp for tray fixing along with GI hard
ware.) -Trays for Power cables.
Note:
1) Include site fabrication of required Bends, T-Junction, Elbows, X-Junction, Z-
Sections, Reducer etc.
2) Including of Cold galvanizing paint on welded spots.
300mm wide x50mm height
4.2.1 Mtrs 50.00 0.00 0.00
225mm wide x50mm height
4.2.2 Mtrs 50.00 0.00 0.00
150mm wide x50mm height
4.2.3 Mtrs 60.00 0.00 0.00
100mm wide x50mm height
4.2.4 Mtrs 100.00 0.00 0.00
75mm wide x50mm height
4.2.5 Mtrs 100.00 0.00 0.00
MS Supports
Supply, Design, Fabrication, Installation, & Commissioning of Steel structures of
channels/ angles/ plates/ Rolled sections/ Pipes/ threaded rod/Suspenders etc for
Base frames, Supports for panels, DBs, cable trays as required, complete with
one coat of approved zinc oxide primer & 2 coats of Synthetic enamel paint, with
5 all fixing accessories etc. complete as per technical specifications, drawings, Kgs 400.00 0.00 0.00
relevant standards & site conditions.
Note:
1) Including of Welding, Bolting, Rivetting, Grouting, Mechanical Fastner (Pin Type
& Sleeve Type) etc.
2) Include Breaking & Finishing of walls, Floors, minor civil work etc.

Supplying and laying of DWC Pipe 160mmdia IS16205 part24 for drawing of UG
6 mtrs 65.00 0.00 0.00
Cables/ELV cables with necessary collars.

7 Excavation
Excavation in all type of soil for Laying LT Armoured power cable at a depth of not
less than 800mm, providing protection with sand Bedding ( min 50mm ) Below and
7.1 Above the cable, alongwith 50mm thick PCC slab over the sand & backfilling the cum 5.00 0.00 0.00
earth with Warning Tape @200mm below Ground Level and compacting and
making good to original condition.
Excavation in all type of soil for Laying LT Armoured power cable at a depth of not
less than 800mm, providing necessary protection thru Humepipes/DWC Pipes &
7.2 cum 75.00 0.00 0.00
backfilling the earth with Warning Tape @200mm below Ground Level and
compacting and making good to original condition.
8 Cable Chamber/Manhole

Providing Masonry Manhole of 750x750x1150 ( clear plastering inside) with Heavy

Nos 2.00 0.00 0.00
Duty Concrete Slab for Cables drawing at any diversions.

TOTAL FOR CABLES & TRAYS

0.00 0.00

F EARTHING
 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR ELECTRICAL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

Rate Amount
S No Description Unit Quantity
Supply Instln Supply Instln
Supply, installation testing & commissioning of Pipe earth Electrode 38 mm dia x 3
mtr G.I. Pipe Earth station, including construction of brick pedestal, providing
1.1 meshed funnel, Heavy Duty CI/ RCC slab cover and other civil Engineering works, Nos 6.00 0.00 0.00
spreading a homogeneous mixture of salt charcoal around the pipe etc, completely
as per IS 3043,1987 or latest revision.( Lift-4 nos, Dishwasher -2 nos )
Supply and laying of following size earth strips including excavation and refilling of
earth when laid in ground and with all fixing accessories when laid inside the
1.2
building including all necessary interconnections with earth station and Panels.
Depth may be 400mm to 500mm.
1.2a 25X3mm GI strip Mtrs 150.00 0.00 0.00

1.2b 1cx10sqmm Cu cable Mtrs 60.00 0.00 0.00

Supplying and running GI/Copper conductor for grounding and (along with other
1.3 wires in conduit system of wiring) using necessary suitable size clamps, nails,
guttas/spacers etc.
GI Wire

1,3a 8 SWG Mtrs 50.00 0.00 0.00

TOTAL FOR EARTHING WORKS 0.00 0.00

 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR ELECTRICAL WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT CANTEEN

Rate Amount
S No Description Unit Quantity
Supply Instln Supply Instln
G WIFI

A CAT (6) UTP DATA/Voice Solution

Supply & Laying of 4-pair, Cat 6 UTP Cable Roll of 305 Mtrs 23AWG LSZH Violet
1 Mtr 300.00 0.00 0.00
RAL 4005 for DATA & Wifi Points with 25mm PVC Conduits
Supply & Fixing of S face plate Dual Port of size 3x3, Material should be ABS 1/2-
2 Nos 9.00 0.00 0.00
port British-style shuttered faceplate, WHITE - Myrius
3 Supply & Fixing of Back Box for Face Plates Nos 9.00 0.00 0.00

Supply & Termination of CAT6 UTP Tool-less Socket with transparent Shutter-1
4 Nos 9.00 0.00 0.00
Module (Myrius) - Work Station Side.

Supply & Termination of Cat 6 24 Port Flat panel equipped with Connectors,
5 Nos 1.00 0.00 0.00
Height, 1U Tooless Mechnisum

6 Supply & Fixing of RJ45 Patch Cord, Category 6, UTP, LSZH, 2 mtr Rack Side Nos 9.00 0.00 0.00

Supply & Fixing of RJ45 Patch Cord, category 6, UTP, LSZH, 1 mtr Work Station
7 Nos 9.00 0.00 0.00
Side

Fiber Backbone Connectivity between Dining Block Panel Room to nearby

B
Hostel Hub Rooms

Supply & Laying of OFC 6Core 50/125Micron OM3 Multimode Outdoor Corrugated
1 Steel tape armored loose tube Jelly field cable (2 Runs from Admin SERVER Mtr 100.00 0.00 0.00
Room)
Supply & Termination of 6F 1U LC MM Loaded with Pigtails, Splice tray, adapter &
2 Nos 1.00 0.00 0.00
splice protectors
Supply & Patching of LC-LC Multimode OM3, 50/125 micron Duplex Patch Cord,3
3 Nos 1.00 0.00 0.00
Meter

4 Supply & Fixing of RJ45 Patch Cord, Category 6, UTP, LSZH, 2 mtr Rack Side Nos 4.00 0.00 0.00

C 9U Wall Mount Rack 500MM D with Accessories No 1.00 0.00 0.00

D Media converter No 2.00 0.00 0.00

Supplying and laying of DWC Pipe 75mmdia IS16205 part24 for drawing of UG
E mtrs 65.00 0.00 0.00
Cables/ELV cables with necessary collars.
Excavation in all type of soil for Laying Fiber Optic cable at a depth of not less
than 800mm, providing necessary protection thru Humepipes/DWC Pipes &
F cum 75.00 0.00 0.00
backfilling the earth with Warning Tape @200mm below Ground Level and
compacting and making good to original condition.
TOTAL FOR WIFI 0.00 0.00

H TV

1 COMMUNICATION OUTLETS

SECTION-2
TV Outlet
1.1 Nos 8.00 0.00 0.00
Supply, fixing, testing and commissioning of TV outlet concealed in wall with
anodized GI box and modular front plate & other accessories, complete as
required.
2 COMMUNICATION OUTLETS WIRING

2.1 TV Wiring (RG6)

Supply and laying of RG6 Co.axial TV cable along with 25mm dia conduit from
2.1.1 electrical room to T.V point including all necessary fixing accessories. Terminating Mtrs 550.00 0.00 0.00
at Main Elec Room.
Supply and laying of RG11 Co.axial TV cable along with 25mm dia conduit from
2.1.2 main electrical room to each floor section-2 elctrical room including all necessary Mtrs 45.00 0.00 0.00
fixing accessories. (OPTION)
3 Fire retardant PVC conduits (For Communication)
Supply and laying of following size Heavy gauge FR PVC conduits concealed in
wall/ ceiling/ floor/ column including supply and drawing of 12SWG GI wire as fish
wire for laying of Communication Cables at a later stage and supply of all fixing
materials like junction boxes, bends, elbows, Ceiling rose, batten holders, solvent
complete as required.
20mm Dia
3.1 Mtrs 150.00 0.00 0.00
25mm Dia
3.2 Mtrs 225.00 0.00 0.00
32mm Dia
3.3 Mtrs 180.00 0.00 0.00
750 x 450 x 100mm Mounting box for Multi Switch
3.4 Nos 2.00 0.00 0.00

0.00 0.00
TOTAL FOR TV
 M/s. Indian Institute of Management, Bangalore
ABSTRACT ESTIMATE FOR EXHAUST AND VENTILATION WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN
HOSTEL MESS AND NIGHT CANTEEN
Sl.No DESCRIPTION Supply Installation
Rs. Rs.

I TOTAL OF VENTILATION SYSTEM 0.00 0.00

II TOTAL OF AIR DISTRIBUTION 0.00 0.00

TOTAL 0.00 0.00

GRAND TOTAL 0.00

GST, EXTRA AS APPLICABLE

 M/s. Indian Institute of Management, Bangalore

ESTIMATE FOR EXHAUST AND VENTILATION WORKS FOR CONSTRUCTION OF DINING BLOCK BETWEEN HOSTEL MESS AND NIGHT
CANTEEN

Supply Installation
Sl.No. Description Unit Quantity
Rate Amount Rate Amount
Rs. Rs. Rs. Rs.
I VENTILATION SYSTEM

KITCHEN VENTILATION FAN

1
Supply, installation, testing & commissioning of Wet type Kitchen
scrubber,Floor mounted as per specification & as indicated in the
drawing. Each complete with Single skin metallic housing with
aluminum/ metallic prefilter, intake louver,double bank GI spray
headers with brass or PVC spray nozzels and PVC water eliminator
and Suitable water supply Monoblock Centrifugal Pump with brass /
GM impeller, The Pump motor shall be suitable for 415±10% volts, 50
cycles/second, 3 phase AC supply (or as per manufacturer standard)
Pump shall be mounted on out side the Air Washer. with SISW/DIDW
Backward curved Centrifugal Fan,to draw fumes through the
scrubber belt drive arrangement, drive guard, MS Frame work for fan,
vibration isolators, fan mouth anti grease filter. The Kitchen Exhaust
Fan scroll shall have inspection / access hatch for blade inspection &
cleaning purpose. Suitable drain plug shall be provided at the bottom
of Fan for easy drain out. Fan Bearing shall be outside the fan for
easy maintainance. fan Motor shall be suitable for 415±10% volts, 50
cycles/second, 3 phase AC supply.

The wet Scrubber should be supplied along with Suitable starter panel
or control panel to operate Fan motor & water circulation pump etc.

Contractor should consider Necessary Electrical power cabling

between Power point (Provided By Electrical Contractor) to Wet
Scrubber's Starter / control Panel (3Mtrs.) and Power or Control cable
from wet scrubber's Starter / control panel to Fan Motor (10Mtrs) and
water circulation Pump (10Mtrs.) etc. (Proper Lugs and Lug paste
should be used for cable termination). (Contractor should select size
of the cable as per their equipment capacity).

Contractor Should consider all kind of Clearance charges,

transportations, transport insurance, loading, unloading & shifting to
the respective places as per HVAC drawing.
GROUND FLOOR
a Exhaust air unit- 3150 CFM External Static pressure – 110mm Nos 1.00 0.00 0.00
b Exhaust air unit- 4600 CFM External Static pressure – 110mm Nos 1.00 0.00 0.00
FIRST FLOOR
Kitchen Exhaust- 2000 CFM Capacity Exhaust air unit External Static
a
pressure – 110mm Nos 1.00 0.00 0.00
CABINET TYPE FRESH AIR FAN
Supplying, installing, testing, commissioning & handing over of Fresh
air unit of cabinet type, with pre-filters with imported Nicotra / Comefri
/ Kruger make fans complete with Fan section and forward curved fan.
2 Heavy duct flexible. These fans to have 40mm static pressure along
with high efficiency drive motors. These fans shall be suitable for
outdoor duty. Motor shall be suitable for 415 + 10% volts, 50 cycles, 3
phase AC supply.
GROUND FLOOR
a Dish wash – 3700 CFM Capacity Fresh air unit Nos 1.00 0.00 0.00
FIRST FLOOR
 Supply Installation
Sl.No. Description Unit Quantity
Rate Amount Rate Amount
Rs. Rs. Rs. Rs.
a Food stagging and Dish wash - 2500 CFM Capacity Fresh air unit Nos 1.00 0.00 0.00
TOTAL FOR VENTILATION SYSTEM 0.00 0.00
II AIR DISTRIBUTION WORKS
Supply, Installation, Testing & Commissioning & Handing over of the
following:
DUCTING
DUCTING WORKS AS PER IS STANDARDS WITH ALL SIZES
MADE OF ANGLE IRON FLANGE JOINTS AS SPECIFIED IN SPEC.

Sheet Metal Work using Angle Iron Flanges for all sizes of the duct
using Lock Former Machine. Fabrication as per IS Standards vide
attached technical specification. Galvanizing shall be Class VII – light
coating of zinc, nominal 120 gm / sqm surface area and Lock Forming
Quality prime material along with mill test certificates. In addition, if
1
deemed necessary, samples of raw material, selected at random by
owner’s site representative shall be subject to approval and tested for
thickness and zinc coating at contractor’s expense. The Duct shall be
supported with Hi-tech Supports at regular intervals as mentioned in
the technical specifications.
GROUND & FIRST FLOOR
a 24 G (0.63 mm) GI ducting Sqmt. 375.00 0.00 0.00
b 22 G (0.80 mm) GI ducting Sqmt. 6.00 0.00 0.00
c 20 G (1.00 mm) GI ducting Sqmt. Rate Only
d 18 G (1.30 mm) GI ducting Sqmt. Rate Only
FRESH AIR / EXHAUST GRILLE
Powder coated, extruded aluminium Fresh air / Exhaust air grille with
2
volume control dampers Sqmt. 1.75 0.00 0.00
VOLUME CONTROL DAMPERS
Supply, installation, testing and balancing of GSS Volume Control
3 Dampers with operating handle for Supply air duct branches in
accordance with the approved shop drawings and specifications. sqmt 1.50 0.00 0.00
FUSIBLE LINK FIRE DAMPER
Fusible link Fire damper made out of 1.6 mm thick GS sheet with
linkages and operating handle of length 150 mm .The temperature
4
rating of fusible link shall be at 72 deg C . ( 90 /180** Minutes fire
rating ) sqmt 1.00 0.00 0.00

Method of measurement:-Fire dampers shall be measured by their

cross-section area perpendicular to air flow. Quoted unit prices shall
include necessary accessories and mounting flanges etc. No
separate measurement shall be made for extension of
cross-section outside the air stream. Frame work for fire dampers
shall not be
estimated separately and shall also be included in unit prices quoted.

EXHAUST & FRESH AIR LOUVER

5 Supply and installation of Exhaust & Fresh Air wall Louver
GROUND FLOOR Sqm. 3.20 0.00 0.00
BACK DRAFT DAMPER WITH GSS COWL FOR EXHAUST FAN

Back Draft Dampers made out of 22/ 20 ** G GSS sheet with circular
6 GI blades to control one side air flow from main duct to exhaust fan /
louvers. The blade shall have rubber gasket beeding for air tightness.

a ROOF Sqmt. 1.00 0.00 0.00

TOTAL FOR AIR DISTRIBUTION WORKS 0.00 0.00