AGROFARM 410 ->

ZKDW350200TD25001
AGROFARM 410 ->
ZKDW470200TD30001
AGROFARM 420 ->
ZKDW390200TD25001
AGROFARM 420 ->
ZKDW510200TD30001
AGROFARM 430 ->
ZKDW430200TD25001

Workshop manual
CONTENTS
0 - Introduction
0.1 - Introduction 0-2
0.1.1 - Safety notes 0-2
0.1.2 - General safety rules 0-2
0.1.3 - Safety precautions for removal and refitting operations 0-3
0.1.4 - Lifting instructions 0-4
0.1.5 - Tightening torques 0-5
0.1.6 - Threadlockers, adhesives, sealants and lubricants 0-8
0.1.7 - Conversion factors 0-10

10 - Technical characteristics
10.1 - Engine 10-2
10.1.1 - Components of the 2012 2V UPS engine 10-2
10.1.2 - Test data and settings 10-8
10.1.3 - Tightening requirements 2012 2V UPS engine 10-9
10.2 - Transmission 10-13
10.2.1 - Transmission (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 410 ->
ZKDW470200TD30001)10-13
10.2.2 - Transmission (AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 420 ->
ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001) 10-20
10.2.3 - Transmission (AGROFARM 430 -> ZKDW550200TD30001) 10-27
10.2.4 - Rear P.T.O. 10-35
10.2.5 - 2 and 4-speed PTO and Groundspeed PTO 10-40
10.2.6 - Hydraulic Reverse Shuttle 10-42
10.3 - Rear axle 10-47
10.3.1 - Park Brake (AGROFARM 430 -> ZKDW550200TD30001) 10-47
10.4 - Front axle 10-48
10.4.1 - Front axle (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 410 ->
ZKDW470200TD30001) 10-48
10.5 - Rear lift 10-53
10.5.1 - Rear lift distributor 10-53

20 - Calibrations and electronic diagnosis

20.1 - Diagnostic tools 20-2
20.1.1 - All Round Tester (ART® SAME) 20-2
20.1.2 - SDF Analyser 20-6
20.1.3 - Serdia 2000 20-11
20.2 - Diagnostic tool screens 20-12
20.2.1 - ECU interrogation 20-12
20.2.2 - HLHP ECU diagnostics - Clutch pedal calibration 20-14
20.2.3 - HLHP ECU diagnostics - “Monitor screens” for ART/PC Tester 20-17
20.2.4 - HLHP ECU diagnostics - “Parameter screens” for ART/PC Tester 20-23
20.2.5 - HLHP ECU diagnostics - “Alarms screens” for ART/PC Tester 20-26
20.2.6 - Test screens for ART/PC Tester 20-29
20.3 - Commissioning and calibrating the tractor 20-32
20.3.1 - Check panel calibration 20-32
20.3.2 - Introduction to commissioning the tractor 20-36

III
 CONTENTS
20.3.3 - Replacing reverse shuttle ECU - Basic commissioning procedure 20-36
20.3.4 - Replacing the reverse shuttle ECU - EEPROM re-initialisation 20-38
20.3.5 - Replacing the reverse shuttle ECU - End-of-line tractor programming 20-39
20.3.6 - Renewal of the shuttle ECU - Introductory notes (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)20-46
20.3.7 - Renewal of the shuttle ECU - Automatic calibration (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)20-46
20.3.8 - Renewal of the shuttle ECU - Manual calibration (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001) 20-49
20.3.9 - Renewal of the shuttle ECU - Editing the comfort parameters (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)20-55
20.3.10 - Replacing the electronic lift ECU - Basic commissioning procedure (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)20-56
20.3.11 - Replacing the electronic lift ECU - EEPROM re-initialisation (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001) 20-58
20.3.12 - Replacing the electronic lift ECU - End-of-line tractor programming (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001) 20-58
20.3.13 - Replacing the electronic lift ECU - Lift calibration (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)20-61
20.4 - ECU alarms 20-63
20.4.1 - Engine alarms 20-63
20.4.2 - Instrument panel alarms 20-76
20.4.3 - Lift alarms 20-79
20.4.4 - HLHP alarms 20-82

30 - Method of intervention
30.1 - Tools for engine disassembly and reassembly 30-2
30.1.1 - Commercially available tools 30-2
30.2 - Workshop tools for engine disassembly and reassembly 30-6
30.2.1 - Workshop tools for engine disassembly and reassembly 30-6
30.3 - B0 - Engine 30-13
30.3.1 - Air conditioning compressor drive belt 30-13
30.3.2 - Tension adjustment of the fan and air conditioning compressor drive belt 30-13
30.3.3 - Alternator, fuel pump and water pump drive belt 30-14
30.3.4 - Tension adjustment of the alternator, fuel pump and water pump drive belt 30-15
30.3.5 - Compression test 30-15
30.3.6 - Assembly and disassembly of the engine on the assembly stand 30-18
30.3.7 - Adjustment of valve clearance 30-22
30.3.8 - Removal and refitting of the rocker arms and pedestals 30-26
30.3.9 - Disassemble and complete the rocker and support, check 30-29

IV
CONTENTS
30.3.10 - Disassembly and assembly of the cylinder head 30-32
30.3.11 - Grinding the cylinder head seal surface 30-39
30.3.12 - Measuring piston protrusion 30-42
30.3.13 - Valve assembly and disassembly 30-45
30.3.14 - Valve check 30-50
30.3.15 - Check the valve guide 30-51
30.3.16 - Replacing the valve guide (oversized - cast) 30-52
30.3.17 - Check the valve residual 30-56
30.3.18 - Replacing the lined valve seat (oversized) 30-58
30.3.19 - Check the endfloat of the crankshaft 30-64
30.3.20 - Check the crankshaft 30-69
30.3.21 - Replace the crankshaft O-ring (flywheel end) 30-72
30.3.22 - Replacing the crankshaft O-ring (opposite end to flywheel) 30-76
30.3.23 - Check the connecting rod drum 30-80
30.3.24 - Fitting and removing piston pin bush 30-88
30.3.25 - Assembly and disassembly of the crankshaft 30-93
30.3.26 - Fitting and removing counterweight shafts, checking 30-100
30.3.27 - Disassembly and assembly of the piston and connecting rod drum 30-107
30.3.28 - Check the piston 30-113
30.3.29 - Check the piston rings and piston grooves 30-115
30.3.30 - Assembly and disassembly of piston cooling nozzles 30-119
30.3.31 - Removal and refitting of the crankcase breather 30-120
30.3.32 - Check the cylinder 30-122
30.3.33 - Removal and refitting of the front cover (opposite end to flywheel) 30-123
30.3.34 - Disassembly and assembly of the connector box 30-128
30.3.35 - Fitting and removing the camshaft bearings, checking 30-130
30.3.36 - Disassembly and assembly of the gear case cover 30-135
30.3.37 - Assembly and disassembly of the camshaft 30-139
30.3.38 - Check the camshaft 30-143
30.3.39 - Removal and refitting of the rotation device 30-144
30.3.40 - Removing and fitting the V-belt pulley 30-146
30.3.41 - Fitting, removing, checking and setting adjuster rod 30-148
30.3.42 - Removal and refitting of the heater 30-153
30.3.43 - Removal and refitting of the turbocharger 30-155
30.3.44 - Removal and refitting of the charge air duct 30-159
30.3.45 - Fitting and removing injection pump 30-163
30.3.46 - Determine the thickness of the shim (engine without injection advance variator) 30-175
30.3.47 - Determine the thickness of the shim (engine with injection advance variator) 30-177
30.3.48 - Determination of the overall dimensions of the injection pump (engine without the
injection advance variator) 30-179
30.3.49 - Determination of the overall dimensions of the injection pump (engine with the injection
advance variator) 30-183
30.3.50 - Fitting and removing injection valves 30-188
30.3.51 - Checking the injection valves 30-192
30.3.52 - Removal and refitting of the fuel lift pump 30-196
30.3.53 - Removal and refitting of the oil pickup pipe 30-198
30.3.54 - Removing and fitting the lubricant oil sump pan (cast iron lubricant oil sump) 30-199
30.3.55 - Disassembly and assembly of the lubricant oil sump (lubricant oil sump-plate) 30-203

V
 CONTENTS
30.3.56 - Removal and refitting of the oil cooler 30-208
30.3.57 - Disassembly and assembly of the oil radiator housing 30-211
30.3.58 - Removal and refitting of the oil pressure switch 30-216
30.3.59 - Removal and refitting of the water pump 30-218
30.3.60 - Testing the thermostat (after removal) 30-220
30.3.61 - Removal and refitting of the thermostat 30-222
30.3.62 - Removal and assembly of the fan support 30-224
30.3.63 - Removal and refitting of the fan support 30-230
30.3.64 - Removal and refitting of the flywheel 30-232
30.3.65 - Replacing the starter motor ring gear on the flywheel 30-234
30.4 - C0 - Engine accessories 30-236
30.4.1 - Starter motor 30-236
30.4.2 - Removing and fitting the engine governor 30-237
30.4.3 - Removal and refitting of the exhaust manifold 30-239
30.4.4 - Removal and refitting of the fuel filter head. 30-242
30.4.5 - Assembly and disassembly of the temperature sender 30-244
30.4.6 - Removal and refitting the engine block 30-246
30.4.7 - Removal and refitting of the alternator (with drivebelt) 30-247
30.4.8 - Disassembly and assembly of the starter 30-251
30.5 - D0 - Transmission 30-253
30.5.1 - Transmission - Adjusting endfloat of planetary reduction unit gears 30-253
30.5.2 - Transmission - Adjusting spring preload 30-253
30.5.3 - Transmission - Adjusting secondary shaft (part No. 927798) 30-255
30.5.4 - Transmission - Adjusting differential bearing preload 30-255
30.5.5 - Transmission - Adjusting pinion position 30-257
30.5.6 - Adjusting mounts - Assembly 30-259
30.5.7 - Shuttle - Removing shuttle unit (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)30-260
30.5.8 - Shuttle- Removing/installing forward drive clutch (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)30-262
30.5.9 - Shuttle - Removing/installing reverse drive clutch (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)30-266
30.6 - F0 - Front axle 30-272
30.6.1 - Front axle - Adjusting differential 30-272
30.7 - R0 - Rear lift 30-283
30.7.1 - ADJUSTING LIFT (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 410 ->
ZKDW470200TD30001) 30-283
30.7.2 - ADJUSTING LIFT (AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 420 ->
ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001, AGROFARM 430 ->
ZKDW550200TD30001) 30-286

40 - Wiring diagrams
40.1 - Introduction 40-2
40.1.1 - Introduction 40-2
40.2 - Components 40-5

VI
CONTENTS
40.2.1 - A - Starting and charging (AGROFARM 410 -> ZKDW350200TD25001) 40-5
40.2.2 - A - Starting and charging (AGROFARM 420 -> ZKDW390200TD25001) 40-11
40.2.3 - A - Starting and charging (AGROFARM 430 -> ZKDW430200TD25001) 40-18
40.2.4 - A - Starting and charging (AGROFARM 410 -> ZKDW470200TD30001) 40-28
40.2.5 - A - Starting and charging (AGROFARM 420 -> ZKDW510200TD30001) 40-34
40.2.6 - A - Starting and charging (AGROFARM 430 -> ZKDW550200TD30001) 40-40
40.2.7 - B - Fuses (AGROFARM 410 -> ZKDW350200TD25001) 40-50
40.2.8 - B - Fuses (AGROFARM 420 -> ZKDW390200TD25001) 40-71
40.2.9 - B - Fuses (AGROFARM 430 -> ZKDW430200TD25001) 40-93
40.2.10 - B - Fuses (AGROFARM 410 -> ZKDW470200TD30001) 40-125
40.2.11 - B - Fuses (AGROFARM 420 -> ZKDW510200TD30001) 40-145
40.2.12 - B - Fuses (AGROFARM 430 -> ZKDW550200TD30001) 40-165
40.2.13 - C - Grounds (AGROFARM 410 -> ZKDW350200TD25001) 40-186
40.2.14 - C - Grounds (AGROFARM 420 -> ZKDW390200TD25001) 40-192
40.2.15 - C - Grounds (AGROFARM 430 -> ZKDW430200TD25001) 40-197
40.2.16 - C - Grounds (AGROFARM 410 -> ZKDW470200TD30001) 40-206
40.2.17 - C - Grounds (AGROFARM 420 -> ZKDW510200TD30001) 40-211
40.2.18 - C - Grounds (AGROFARM 430 -> ZKDW550200TD30001) 40-216
40.2.19 - D - Intermediate connections (AGROFARM 410 -> ZKDW350200TD25001) 40-222
40.2.20 - D - Intermediate connections (AGROFARM 420 -> ZKDW390200TD25001) 40-242
40.2.21 - D - Intermediate connections (AGROFARM 430 -> ZKDW430200TD25001) 40-262
40.2.22 - D - Intermediate connections (AGROFARM 410 -> ZKDW470200TD30001) 40-293
40.2.23 - D - Intermediate connections (AGROFARM 420 -> ZKDW510200TD30001) 40-313
40.2.24 - D - Intermediate connections (AGROFARM 430 -> ZKDW550200TD30001) 40-334
40.2.25 - E - On-board instruments and visual and audible indicators (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001) 40-361
40.2.26 - E - On-board instruments and visual and audible indicators (AGROFARM 430 ->
ZKDW430200TD25001)40-362
40.2.27 - E - On-board instruments and visual and audible indicators (AGROFARM 410 ->
ZKDW470200TD30001)40-363
40.2.28 - E - On-board instruments and visual and audible indicators (AGROFARM 420 ->
ZKDW510200TD30001)40-364
40.2.29 - E - On-board instruments and visual and audible indicators (AGROFARM 430 ->
ZKDW550200TD30001)40-365
40.2.30 - F - External lights (rotating beacon) (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001) 40-366
40.2.31 - F - External lights (rotating beacon) (AGROFARM 430 -> ZKDW430200TD25001) 40-367
40.2.32 - F - External lights (rotating beacon) (AGROFARM 410 -> ZKDW470200TD30001) 40-369
40.2.33 - F - External lights (rotating beacon) (AGROFARM 420 -> ZKDW510200TD30001) 40-370
40.2.34 - F - External lights (rotating beacon) (AGROFARM 430 -> ZKDW550200TD30001) 40-373
40.2.35 - G - Interior lights (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 420 ->
ZKDW390200TD25001) 40-374
40.2.36 - G - Interior lights (AGROFARM 430 -> ZKDW430200TD25001) 40-375
40.2.37 - G - Interior lights (AGROFARM 410 -> ZKDW470200TD30001) 40-375
40.2.38 - G - Interior lights (AGROFARM 420 -> ZKDW510200TD30001) 40-375
40.2.39 - G - Interior lights (AGROFARM 430 -> ZKDW550200TD30001) 40-375
40.2.40 - H - Manual electrical controls (steering column switch) (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001) 40-375

VII
 CONTENTS
40.2.41 - H - Manual electrical controls (steering column switch) (AGROFARM 430 ->
ZKDW430200TD25001)40-377
40.2.42 - H - Manual electrical controls (steering column switch) (AGROFARM 410 ->
ZKDW470200TD30001) 40-380
40.2.43 - H - Manual electrical controls (steering column switch) (AGROFARM 420 ->
ZKDW510200TD30001) 40-382
40.2.44 - H - Manual electrical controls (steering column switch) (AGROFARM 430 ->
ZKDW550200TD30001) 40-384
40.2.45 - I - Circuit breakers (AGROFARM 410 -> ZKDW350200TD25001) 40-386
40.2.46 - I - Circuit breakers (AGROFARM 420 -> ZKDW390200TD25001) 40-398
40.2.47 - I - Circuit breakers (AGROFARM 430 -> ZKDW430200TD25001) 40-410
40.2.48 - I - Circuit breakers (AGROFARM 410 -> ZKDW470200TD30001) 40-426
40.2.49 - I - Circuit breakers (AGROFARM 420 -> ZKDW510200TD30001) 40-437
40.2.50 - I - Circuit breakers (AGROFARM 430 -> ZKDW550200TD30001) 40-448
40.2.51 - J - Relays (AGROFARM 410 -> ZKDW350200TD25001) 40-460
40.2.52 - J - Relays (AGROFARM 420 -> ZKDW390200TD25001) 40-466
40.2.53 - J - Relays (AGROFARM 430 -> ZKDW430200TD25001) 40-473
40.2.54 - J - Relays (AGROFARM 410 -> ZKDW470200TD30001) 40-483
40.2.55 - J - Relays (AGROFARM 420 -> ZKDW510200TD30001) 40-489
40.2.56 - J - Relays (AGROFARM 430 -> ZKDW550200TD30001) 40-496
40.2.57 - K - Sensors and transmitters (AGROFARM 410 -> ZKDW350200TD25001) 40-504
40.2.58 - K - Sensors and transmitters (AGROFARM 420 -> ZKDW390200TD25001) 40-508
40.2.59 - K - Sensors and transmitters (AGROFARM 430 -> ZKDW430200TD25001) 40-512
40.2.60 - K - Sensors and transmitters (AGROFARM 410 -> ZKDW470200TD30001) 40-519
40.2.61 - K - Sensors and transmitters (AGROFARM 420 -> ZKDW510200TD30001) 40-524
40.2.62 - K - Sensors and transmitters (AGROFARM 410 -> ZKDW350200TD25001) 40-529
40.2.63 - L - Electromagnets and solenoid valves (AGROFARM 410 -> ZKDW350200TD25001) 40-535
40.2.64 - L - Electromagnets and solenoid valves (AGROFARM 420 -> ZKDW390200TD25001) 40-536
40.2.65 - L - Electromagnets and solenoid valves (AGROFARM 430 -> ZKDW430200TD25001) 40-537
40.2.66 - L - Electromagnets and solenoid valves (AGROFARM 410 -> ZKDW470200TD30001) 40-538
40.2.67 - L - Electromagnets and solenoid valves (AGROFARM 420 -> ZKDW510200TD30001) 40-539
40.2.68 - L - Electromagnets and solenoid valves (AGROFARM 430 -> ZKDW550200TD30001) 40-541
40.2.69 - M - Electrical/electronic devices, Flasher units and Timers (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001) 40-542
40.2.70 - M - Electrical/electronic devices, Flasher units and Timers (AGROFARM 430 ->
ZKDW430200TD25001)40-543
40.2.71 - M - Electrical/electronic devices, Flasher units and Timers (AGROFARM 410 ->
ZKDW470200TD30001)40-544
40.2.72 - M - Electrical/electronic devices, Flasher units and Timers (AGROFARM 420 ->
ZKDW510200TD30001)40-545
40.2.73 - M - Electrical/electronic devices, Flasher units and Timers (AGROFARM 430 ->
ZKDW550200TD30001)40-547
40.2.74 - N - Electric motors and actuators (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001) 40-548
40.2.75 - N - Electric motors and actuators (AGROFARM 430 -> ZKDW430200TD25001) 40-549
40.2.76 - N - Electric motors and actuators (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001) 40-552
40.2.77 - N - Electric motors and actuators (AGROFARM 430 -> ZKDW550200TD30001) 40-553

VIII
CONTENTS
40.2.78 - O - Resistors and rheostats (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM
420 -> ZKDW390200TD25001) 40-555
40.2.79 - O - Resistors and rheostats (AGROFARM 430 -> ZKDW430200TD25001) 40-555
40.2.80 - O - Resistors and rheostats (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM
420 -> ZKDW510200TD30001) 40-555
40.2.81 - O - Resistors and rheostats (AGROFARM 430 -> ZKDW550200TD30001) 40-555
40.2.82 - P - Various services (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 420 ->
ZKDW390200TD25001) 40-556
40.2.83 - P - Various services (AGROFARM 430 -> ZKDW430200TD25001) 40-557
40.2.84 - P - Various services (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 ->
ZKDW510200TD30001) 40-559
40.2.85 - P - Various services (AGROFARM 430 -> ZKDW550200TD30001) 40-560
40.2.86 - Q - Safety devices (AGROFARM 410 -> ZKDW350200TD25001) 40-562
40.2.87 - Q - Safety devices (AGROFARM 420 -> ZKDW390200TD25001) 40-566
40.2.88 - Q - Safety devices (AGROFARM 430 -> ZKDW430200TD25001) 40-571
40.2.89 - Q - Safety devices (AGROFARM 410 -> ZKDW470200TD30001) 40-579
40.2.90 - Q - Safety devices (AGROFARM 420 -> ZKDW510200TD30001) 40-583
40.2.91 - Q - Safety devices (AGROFARM 430 -> ZKDW550200TD30001) 40-587
40.2.92 - R - Diagnostics (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 420 ->
ZKDW390200TD25001) 40-595
40.2.93 - R - Diagnostics (AGROFARM 430 -> ZKDW430200TD25001) 40-595
40.2.94 - R - Diagnostics (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 ->
ZKDW510200TD30001) 40-595
40.2.95 - R - Diagnostics (AGROFARM 430 -> ZKDW550200TD30001) 40-595
40.3 - Systems 40-596
40.3.1 - S001 - Cab engine start - ITA (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM
420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001) 40-596
40.3.2 - S001 - Cab engine start - ITA (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM
420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001) 40-600
40.3.3 - S001 - Cab engine start - USA (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM
420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001) 40-604
40.3.4 - S001 - Cab engine start - USA (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM
420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001) 40-609
40.3.5 - S001 - Engine start, cab with electronic lift (AGROFARM 430 -> ZKDW430200TD25001)40-613
40.3.6 - S001 - Engine start, cab with electronic lift (AGROFARM 430 -> ZKDW550200TD30001)40-617
40.3.7 - S001 - Cab engine start - ITA (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM
420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001) 40-621
40.3.8 - S001 - Cab engine start - ITA (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM
420 -> ZKDW510200TD30001) 40-625
40.3.9 - S001 - Engine start, platform version - USA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)40-629
40.3.10 - S001 - Engine start, platform version - USA (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001) 40-633
40.3.11 - S002 - Heating, standard cab (heater and air conditioning) - ITA 40-637
40.3.12 - S002 - Heating, standard cab - ITA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)40-642
40.3.13 - S002 - Heating, standard cab (heater and air conditioning) - USA 40-647
40.3.14 - S002 - Heating, standard cab - USA (AGROFARM 410 -> ZKDW350200TD25001,

IX
 CONTENTS
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)40-652
40.3.15 - S002 - Heating, standard cab (heater and air conditioning) with electronic lift
(AGROFARM 430 -> ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001)
40-657
40.3.16 - S002 - Heating, standard cab with electronic lift (AGROFARM 430 ->
ZKDW430200TD25001)40-661
40.3.17 - S003 - Air conditioning, standard cab 40-665
40.3.18 - S003 - Air conditioning, cab with high visibility roof 40-671
40.3.19 - S003 - Air conditioning, cab with high visibility roof - USA 40-677
40.3.20 - S003 - Air conditioning, standard cab - USA 40-683
40.3.21 - S003 - Air conditioning, standard cab with electronic lift (AGROFARM 430 ->
ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001) 40-689
40.3.22 - S003 - Air conditioning, cab with high visibility roof and electronic lift (AGROFARM 430
-> ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001) 40-695
40.3.23 - S004 - Starting and preheating, cab 40-701
40.3.24 - S004 - Starting and preheating, cab - USA 40-705
40.3.25 - S004 - Engine and preheat, cab version with electronic lift (AGROFARM 430 ->
ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001) 40-710
40.3.26 - S004 - Starting and preheating, platform (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKDW390200TD25001,
AGROFARM 420 -> ZKDW510200TD30001) 40-714
40.3.27 - S004 - Starting and preheating, platform - USA (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 ->
ZKDW390200TD25001, AGROFARM 420 -> ZKDW510200TD30001) 40-719
40.3.28 - S005 - PTO, cab version 40-723
40.3.29 - S005 - PTO, cab version - USA 40-728
40.3.30 - S005 - PTO, cab version with front lift (AGROFARM 430 -> ZKDW430200TD25001,
AGROFARM 430 -> ZKDW550200TD30001) 40-734
40.3.31 - S005 - PTO, platform version (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM
410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKDW390200TD25001, AGROFARM
420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001) 40-738
40.3.32 - S005 - PTO, platform version - USA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKDW390200TD25001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001)40-744
40.3.33 - S006 - Windscreen wipers, cab with high visibility roof 40-750
40.3.34 - S006 - Windscreen wipers, standard cab with heater and air conditioning 40-755
40.3.35 - S006 - Windscreen wipers, version with standard cab (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 ->
ZKDW430200TD25001) 40-759
40.3.36 - S006 - Windscreen wipers, cab with high visibility roof - USA 40-764
40.3.37 - S006 - Windscreen wipers, standard cab with heater and air conditioning - USA 40-769
40.3.38 - S006 - Windscreen wipers, version with standard cab - USA (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 ->
ZKDW430200TD25001)40-773
40.3.39 - S006 - Windscreen wipers, cab with high visibility roof and electronic lift (AGROFARM
430 -> ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001) 40-778
40.3.40 - S006 - Windscreen wipers, standard cab with heater, air conditioning and electronic lift
(AGROFARM 430 -> ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001)

X
CONTENTS
 40-783
40.3.41 - S006 - Windscreen wipers, standard cab with electronic lift (AGROFARM 430 ->
ZKDW430200TD25001) 40-787
40.3.42 - S007 - Instrument panel, cab (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM
420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001) 40-791
40.3.43 - S007 - Instrument panel, cab (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM
420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001) 40-799
40.3.44 - S007 - Instrument panel, platform (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)40-807
40.3.45 - S007 - Instrument panel, platform (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001) 40-817
40.3.46 - S007 - Instrument panel, cab version - USA (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 ->
ZKDW430200TD25001) 40-827
40.3.47 - S007 - Instrument panel, cab version - USA (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001) 40-835
40.3.48 - S007 - Instrument panel, platform version - USA (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 ->
ZKDW430200TD25001) 40-843
40.3.49 - S007 - Instrument panel, platform version - USA (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001) 40-853
40.3.50 - S007 - Instrument panel, cab with electronic lift (AGROFARM 430 ->
ZKDW430200TD25001) 40-863
40.3.51 - S007 - Instrument panel, cab with electronic lift (AGROFARM 430 ->
ZKDW550200TD30001) 40-870
40.3.52 - S008 - Brakes, cab version - ITA 40-877
40.3.53 - S008 - Brakes, cab version - USA 40-883
40.3.54 - S008 - Brakes, platform version - ITA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKDW390200TD25001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001)40-890
40.3.55 - S008 - Brakes, platform version \- USA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKDW390200TD25001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001)40-896
40.3.56 - S008 - Brakes, cab with electronic lift (AGROFARM 430 -> ZKDW550200TD30001) 40-903
40.3.57 - S008 - Brakes, cab with electronic lift (AGROFARM 430 -> ZKDW430200TD25001) 40-910
40.3.58 - S009 - Cab lights - ITA (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 420
-> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001) 40-916
40.3.59 - S009 - Cab lights - ITA (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420
-> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001) 40-922
40.3.60 - S009 - Cab lights - USA (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 420
-> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001) 40-928
40.3.61 - S009 - Cab lights - USA (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420
-> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001) 40-935
40.3.62 - S009 - Lights, platform version - ITA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)40-942
40.3.63 - S009 - Lights, platform version - ITA (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001) 40-948

XI
 CONTENTS
40.3.64 - S009 - Lights, platform version - USA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)40-953
40.3.65 - S009 - Lights, platform version - USA (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001) 40-959
40.3.66 - S009 - Lights, cab with electronic lift (AGROFARM 430 -> ZKDW430200TD25001) 40-964
40.3.67 - S009 - Lights, cab with electronic lift (AGROFARM 430 -> ZKDW550200TD30001) 40-970
40.3.68 - S010 - Work lights, standard cab - ITA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)40-976
40.3.69 - S010 - Work lights, standard cab - ITA (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)40-985
40.3.70 - S010 - Work lights, standard cab - USA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)40-993
40.3.71 - S010 - Work lights, standard cab - USA (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)
40-1001
40.3.72 - S010 - Work lights, standard cab with electronic lift (AGROFARM 430 ->
ZKDW430200TD25001) 40-1009
40.3.73 - S010 - Work lights, standard cab with electronic lift (AGROFARM 430 ->
ZKDW550200TD30001)40-1016
40.3.74 - S010 - Work lights, HV cab - ITA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
40-1025
40.3.75 - S010 - Work lights, HV cab - ITA (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)
40-1033
40.3.76 - S010 - Work lights, HV cab - USA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
40-1043
40.3.77 - S010 - Work lights, HV cab - USA (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)
40-1050
40.3.78 - S010 - Work lights, HV cab with electronic lift (AGROFARM 430 ->
ZKDW430200TD25001)40-1060
40.3.79 - S010 - Work lights, HV cab with electronic lift (AGROFARM 430 ->
ZKDW550200TD30001) 40-1068
40.3.80 - S010 - Work lights, platform version - ITA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
40-1077
40.3.81 - S010 - Work lights, platform version - ITA (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001) 40-1082
40.3.82 - S010 - Work lights, platform version - USA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
 40-1088
40.3.83 - S010 - Work lights, platform version - USA (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001) 40-1093
40.3.84 - S011 - Cab accessories - ITA (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM
420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001) 40-1100
40.3.85 - S011 - Cab accessories - ITA (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM

XII
CONTENTS
420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001) 40-1105
40.3.86 - S011 - Cab accessories - USA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
40-1110
40.3.87 - S011 - Cab accessories - USA (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)
40-1115
40.3.88 - S011 - Accessories, cab with electronic lift (AGROFARM 430 -> ZKDW430200TD25001)
40-1120
40.3.89 - S011 - Accessories, cab with electronic lift (AGROFARM 430 -> ZKDW550200TD30001)
40-1125
40.3.90 - S011 - Platform accessories - ITA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
40-1130
40.3.91 - S011 - Platform accessories - ITA (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001) 40-1134
40.3.92 - S011 - Platform accessories - USA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
 40-1138
40.3.93 - S011 - Platform accessories - USA (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001) 40-1142
40.3.94 - S012 - Transmission, ITA cab version (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
40-1145
40.3.95 - S012 - Transmission, ITA cab version (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)
40-1152
40.3.96 - S012 - Transmission, ITA cab version (AGROFARM 420 -> ZKDW510200TD30001,
AGROFARM 430 -> ZKDW550200TD30001) 40-1159
40.3.97 - S012- Transmission, ITA platform version (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
40-1166
40.3.98 - S012- Transmission, ITA platform version (AGROFARM 410 -> ZKDW470200TD30001)
40-1172
40.3.99 - S012- Transmission, ITA platform version (AGROFARM 420 -> ZKDW510200TD30001)
 40-1179
40.3.100 - S012- Transmission, USA cab version (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
 40-1186
40.3.101 - S012- Transmission, USA cab version (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)
 40-1192
40.3.102 - S012- Transmission, USA cab version (AGROFARM 420 -> ZKDW510200TD30001,
AGROFARM 430 -> ZKDW550200TD30001) 40-1199
40.3.103 - S012- Transmission, USA platform version (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 ->
ZKDW430200TD25001)40-1206
40.3.104 - S012- Transmission, USA platform version (AGROFARM 410 ->

XIII
 CONTENTS
ZKDW470200TD30001)40-1212
40.3.105 - S012- Transmission, USA platform version (AGROFARM 420 ->
ZKDW510200TD30001) 40-1219
40.3.106 - S012 - Transmission, cab with electronic lift (AGROFARM 430 ->
ZKDW430200TD25001)40-1226
40.3.107 - S012 - Transmission, cab with electronic lift (AGROFARM 430 ->
ZKDW550200TD30001)40-1231
40.3.108 - S013 - Distributors, cab version (AGROFARM 420 -> ZKDW390200TD25001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001,
AGROFARM 430 -> ZKDW550200TD30001) 40-1237
40.3.109 - S013 - Distributors, cab version - USA (AGROFARM 420 -> ZKDW390200TD25001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001,
AGROFARM 430 -> ZKDW550200TD30001) 40-1240
40.3.110 - S013 - Distributors, cab with electronic lift (AGROFARM 430 -> ZKDW430200TD25001,
AGROFARM 430 -> ZKDW550200TD30001) 40-1243
40.3.111 - S014 - CAN Bus, cab version (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
40-1247
40.3.112 - S014 - CAN Bus, cab version (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)
40-1250
40.3.113 - S014 - Can Bus, platform version (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
40-1255
40.3.114 - S014 - Can Bus, platform version (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001) 40-1258
40.3.115 - S014 - CAN Bus, cab with electronic lift (AGROFARM 430 -> ZKDW430200TD25001)40-1263
40.3.116 - S014 - CAN Bus, cab with electronic lift (AGROFARM 430 -> ZKDW550200TD30001)40-1266
40.3.117 - S015 - Electronic lift (AGROFARM 430 -> ZKDW430200TD25001, AGROFARM 430 ->
ZKDW550200TD30001)40-1270
40.4 - Wiring harnesses 40-1274
40.4.1 - 0.010.2147.2 - Heating 40-1274
40.4.2 - 0.010.2153.2 - Air conditioning 40-1275
40.4.3 - 0.010.4516.3 - Windscreen wiper, without high visibility cab 40-1277
40.4.4 - 0.010.6468.3/10 - Pneumatic seat 40-1279
40.4.5 - 0.011.3597.3 - Windscreen wiper, with high visibility cab 40-1279
40.4.6 - 0.012.2756.3 - Front PTO solenoid valve 40-1282
40.4.7 - 0.013.4085.4/20 - Front work lights (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)
 40-1283
40.4.8 - 0.013.4909.4 - Rear lights 40-1285
40.4.9 - 0.013.4910.4 - Rear sidelights and turn indicators 40-1286
40.4.10 - 0.013.6327.4 - Rotating beacon 40-1287
40.4.11 - 0.014.1645.4/10 - Air-hydraulic braking pressure switch ITA/D 40-1287
40.4.12 - 0.014.3927.4/40 - Front work light 40-1288
40.4.13 - 0.014.8666.4/30 - Front lights and horn (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)
 40-1289

XIV
CONTENTS
40.4.14 - 0.014.9195.4/20 - Preheating 40-1291
40.4.15 - 0.014.9281.4 - Work light and rotating beacon, platform (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 ->
ZKDW390200TD25001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW430200TD25001) 40-1292
40.4.16 - 0.015.1418.4/30 - Hydraulic reverse shuttle in cab 40-1293
40.4.17 - 0.015.1440.4 - Hydraulic reverse shuttle 40-1295
40.4.18 - 0.015.1983.4/10 - Power 40-1296
40.4.19 - 0.015.1998.4/10 - Hydraulic reverse shuttle, drivetrain (AGROFARM 410 ->
ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001) 40-1297
40.4.20 - 0.015.4257.4/10 - PTO sensor - (USA EXPORT) 40-1300
40.4.21 - 0.015.6123.4 - Rear screen wiper, without high visibility cab 40-1300
40.4.22 - 0.015.6272.4/40 - Roof, with High Visibility cab 40-1301
40.4.23 - 0.015.7023.4/50 - Rear wiring loom, with digital instrument panel 40-1306
40.4.24 - 0.015.7266.4/40 - Air conditioning condenser fan 40-1308
40.4.25 - 0.015.7309.4 - Front lights and horn (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
40-1310
40.4.26 - 0.016.0373.4/30 - Cab power supply 40-1312
40.4.27 - 0.016.0664.4 - Low rear work lights 40-1313
40.4.28 - 0.016.0664.4 - Low rear work lights 40-1315
40.4.29 - 0.016.0849.4 - Front sidelights and turn indicators (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 ->
ZKDW390200TD25001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW430200TD25001)40-1317
40.4.30 - 0.016.0865.4/10 - Roof, with standard cab (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
 40-1318
40.4.31 - 0.016.0866.4/10 - Work lights and windscreen wiper, without High Visibility cab 40-1322
40.4.32 - 0.016.1001.420 - Hydraulic trailer braking valve (AGROFARM 430 ->
ZKDW550200TD30001)40-1324
40.4.33 - 0.016.2000.4/20 - Engine, version without front lift 40-1325
40.4.34 - 0.016.2001.4/10 - Engine, version with front lift 40-1327
40.4.35 - 0.017.0474.4 - Battery positive terminal 40-1329
40.4.36 - 0.017.1063.4 - Cab earth 40-1329
40.4.37 - 0.017.8922.410 - Battery negative, with front lift 40-1330
40.4.38 - 0.017.9016.410 - Battery negative, without front lift 40-1330
40.4.39 - 0.018.3567.4/60 - Central wiring loom, cab 40-1331
40.4.40 - 0.018.4081.4/30 - Central wiring loom, cab - USA 40-1348
40.4.41 - 0.018.4139.4 - Auxiliary distributor control (AGROFARM 420 -> ZKDW390200TD25001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001,
AGROFARM 430 -> ZKDW550200TD30001) 40-1365
40.4.42 - 0.018.4537.4/40 - Central wiring loom, cab and electronic lift (AGROFARM 430 ->
ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001) 40-1366
40.4.43 - 0.018.4657.4/10 - Electronic lift (AGROFARM 430 -> ZKDW430200TD25001,
AGROFARM 430 -> ZKDW550200TD30001) 40-1383
40.4.44 - 0.018.4758.4 - Auxiliary distributor, with electronic lift (AGROFARM 430 ->

XV
 CONTENTS
ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001) 40-1384
40.4.45 - 0.018.4891.4 - Rear wiring loom, with lift electronic (AGROFARM 430 ->
ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001) 40-1385
40.4.46 - 0.018.5230.4/10 - RH side console, electronic lift (AGROFARM 430 ->
ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001) 40-1387
40.4.47 - 0.018.5346.4 - Distributor, with mechanical lift (AGROFARM 420 ->
ZKDW390200TD25001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001) 40-1388
40.4.48 - 0.018.5825.4 - Roof, standard cab with heater and air conditioning 40-1389
40.4.49 - 0.018.5908.4 - Rear lights wiring loom () 40-1391
40.4.50 - 0.018.7845.4/20 - Central wiring loom, platform (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 ->
ZKDW390200TD25001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW430200TD25001) 40-1393
40.4.51 - 0.018.8008.4 - Central wiring loom, platform - USA (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 ->
ZKDW390200TD25001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW430200TD25001)40-1410
40.4.52 - 0.019.1994.4 - H/L lever (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 420
-> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001) 40-1424
40.4.53 - 0.019.5535.4 - Front work lights, with HV cab and FOPS roll cage. 40-1425
40.4.54 - 04215655 - Engine 40-1426
40.4.55 - 0441.1923.4 - Lower front lights 40-1428

XVI
0 - Introduction

0-1
 Introduction
0.1 - Introduction
The purpose of this workshop manual is to provide instructions for repair technicians and a practical guide for improvement of the
quality of repairs. This manual enables repair technicians to acquire a thorough knowledge of the engine, indicating the correct me-
thods for fault diagnosis, for working in safety and for accurate dimensional checks and visual inspections of parts subject to repair.
The instructions also indicate the products to use, the tightening torques and the adjustment data. The technical material contained in
this manual is reserved for Authorised Dealers and Service Centres who will be duly informed of any technical changes to the engines
in question through the issue of documents regarding modifications, updates and supplements for optional equipment. All technicians
and their colleagues are expressly forbidden from reproducing any part of this manual in any form or from communicating the con-
tents to third parties without the express written permission of the Manufacturer, which remains the sole owner of this document with
all rights reserved in accordance with applicable laws.
0.1.1 - Safety notes
To ensure that engines entrusted to Authorised Service Centres for repair or overhaul continue to function correctly, it is very impor-
tant that all repair work is carried out in the prescribed manner. The procedures for checks and repairs indicated in this manual are
safe and effective. Some of the operations described require the use of special tools and equipment; these tools have been specifi-
cally designed for the intended purpose and may be ordered directly from the Manufacturer. DO NOT USE MAKESHIFT TOOLS; not
only is there a risk of personal injury, but such tools are rarely suited to the purpose for which they are used. In potentially hazardous
situations, always give priority to personal safety and take the necessary actions to eliminate the danger
0.1.2 - General safety rules
l Even if you have a thorough knowledge of the engine as regards its components, operation and controls, always take particu-
lar care when carrying out manoeuvres or movements; Remember that the engine you are working on is in need of repair or
overhaul and consequently may not always behave as expected.
l Before starting work, clean the engine thoroughly to remove all mud, dust and road dirt.
l When carrying out checks and repairs, wear close-fitting clothing, safety goggles and protective gloves that are suitable for
the task (cleaning, draining fluids, repairs). When working near moving parts, long hair should be gathered up and tied back
safely under a cap to prevent the risk of entanglement and severe injury.
l Do not allow anyone who is not directly involved in the work to come near the engine; ensure that they remain at a safe dis-
tance.
l Keep well clear of moving parts; when the engine is running, some moving parts are not easily visible and therefore present a
risk of entanglement, even if protected by safety guards.
l Ensure that the area is well ventilated before starting the engine in order to avoid the formation of dangerous concentrations
of toxic gases; always connect suitable fumes extraction equipment to the exhaust pipe.
l Do not start the engine with the safety guards removed under any circumstances; all repair and adjustment operations must
be carried out with the engine stopped.
l Do not top up fuel, oil or coolant levels when the engine is running.
l Never smoke and ensure there are no naked flames nearby when topping up fuel or oil.
l Before checking or removing the battery, stop the engine and remove the key from the starter switch.
l Remove the battery and recharge in a well-ventilated area where the temperature exceeds 0°C.
l When checking or recharging the battery, do not smoke or allow naked flames in the vicinity as the hydrogen gas given off by
the battery is highly explosive.
l The liquid (electrolyte) contained in the battery is very harmful if it comes into contact with the skin and the eyes; for this rea-
son, always wear gloves and safety goggles with side shields when checking or topping up the battery. Should any electrolyte
accidentally come into contact with your skin, wash the affected areas immediately with plenty of fresh water; if electrolyte
comes into contact with your clothing, this should be removed as soon as possible. In case of accidental ingestion of elec-
trolyte, drink plenty of water, milk or vegetable oil, take antacids such as magnesium, bicarbonate, etc. and seek medical
attention immediately.
l Before working on the electrical systems, always disconnect the battery terminals.
DANGER
Always disconnect the negative lead (--) before the positive lead (+); when re-connecting the battery on completion of
the work, first connect the positive terminal (+) and then the negative (--).

l No welding is permitted on the engine.

l When topping up lubricants, always wear suitable protective gloves.
l Do not wear clothing contaminated by engine oil or hydraulic oil; prolonged contact with the skin can be harmful and may
cause allergic reactions.

0-2
Introduction
l Used engine oil and hydraulic oil must be disposed of properly; recover used lubricants and dispose of them in accordance
with the applicable regulations.
l Before carrying out any work on the hydraulic or pneumatic systems, discharge all residual pressure from the circuits.
l Before carrying out any work on the hydraulic system or engine, allow the oil and engine coolant to cool down.
l When removing and refitting certain assemblies, it will be necessary to support the engine; use stands, jacks or blocks capable
of supporting the weight and arrange them in a triangular pattern to prevent the engine from overturning.
l To lift heavy components, use a hoist or crane. Check that wire ropes, chains or fibre slings are not worn and that hooks are
not damaged.
l Always use lifting equipment of suitable capacity for the weight of the components to be removed. Ensure lifting equipment is
attached correctly.
l When lifting or supporting an assembly or component, manoeuvre the parts slowly and carefully to avoid swinging movements
or collision with other components.
l Never work on components suspended from a hoist or crane.
l When removing the retaining bolts of a component that could fall, always leave two opposing bolts in place for safety; before
removing these last two screws, attach the component to suitable lifting equipment or position support blocks.
l Any oil or fuel spilled during removal or dismantling operations should be cleaned up as soon as possible to prevent the risk
of slipping and fire.
l When refitting electrical wiring looms and wires, ensure that they are properly secured with their original retaining straps or
brackets to prevent the possibility of damage caused by vibration.
l Never insert your fingers or hands to check the alignment between fixing holes in components; always use a suitable dowel
of soft material.
l When refitting assemblies or components, always use the specified tightening torques; the tightening torques indicated in the
headings regarding assembly/refitting operations have been determined through experimentation and must be scrupulously
adhered to.
l When refitting parts that are subject to vibration or that rotate at high speed, take particular care when carrying out final instal-
lation checks.

0.1.3 - Safety precautions for removal and refitting operations

When removing or refitting parts, always take the following safety precautions.
Precautions for removal operations
l After disconnecting hydraulic and fuel system pipes, always fit plugs to the open ends of the pipes to prevent ingress of dirt.
l Use containers of sufficient capacity when draining oil, coolant or fuel.
l Before removing a part from the machine, check for alignment markings indicating the correct assembly position. If necessary,
make new markings to ensure correct assembly.
l When unplugging electrical connectors, always grip the connectors firmly to avoid pulling on the wires.
l Where necessary, label wires and pipes before removal to avoid confusion when reconnecting.
l Check the number and thickness of any shims removed and keep them together in a safe place.
l To lift the engine or any of its main components, use lifting equipment of suitable capacity.
l When using eyebolts for lifting components, first check that they are not deformed; screw them fully home and then turn the
bolt so that the eye is aligned with the lifting hook.
l Before removing a part, clean the surrounding area and, after removing the part, cover it to protect it from dirt and dust.
Precautions for refitting operations
l Tighten nuts and screws to the specified tightening torques.
l When refitting flexible pipes and cables, take care not to twist or tangle them.
l Always fit new seals, O-rings, split pins and safety stop rings; make sure that the ends of the split pins are separated and bent
back so that the pin cannot be withdrawn from the hole.
l Ensure that circlips are correctly installed in their grooves.
l When applying threadlocking compound, first clean the part to remove all oil and grease, then cover the thread evenly apply-
ing a few drops of the compound.
l When applying sealant, first clean the surface removing all traces of oil and grease and check for dirt or indentations, then
apply the sealant evenly making sure that it forms a continuous film around any fixing holes.
l Clean all parts, removing dirt, oxidisation, carbon deposits, burrs and indentations.
l Coat all moving parts with a thin film of engine oil.
l When reconnecting electrical wiring connectors, first remove all traces of oil, dust and water from the inside of the connector
and then push the two halves together firmly; connectors with locking tabs should be pushed together until the tab engages
the keeper.
l Bolt down flanged fittings evenly, tightening the screws gradually in a crosswise pattern.

0-3
 Introduction
Precautions to be taken on completion of removal/refitting operations
l If coolant has been drained from the engine, refit the drain plug and pour in new coolant to the correct level. Start the engine
to circulate the coolant and then check the level again and top up.
l After removing hydraulic components, top up the hydraulic oil to the specified level. Start the engine to circulate the oil in the
hydraulic circuits and then recheck the level and top up as necessary.
l After having removed a variable displacement pump, connect the drain pipe and fill the pump casing with oil through the filler
hole provided.
l Grease stub axle housings, cylinder pivot mountings and drive shafts thoroughly after assembly.

0.1.4 - Lifting instructions

DANGER
Components weighing over 25 kg or of significant size must be supported and removed using suitable lifting equip-
ment with wire rope or polyester slings.

Wire ropes - slings

l Use wire ropes or polyester slings of suitable capacity for the parts to be lifted, referring to the following tables:
Table 1
WIRE ROPES (standard twisted “S” or “Z” type) POLYESTER SLINGS (eye-and-eye - simple loop)
Ø rope mm Capacity (kg) Width (mm) Capacity (kg)

8 650 620 500 25 500 400 860 700

10 1000 1740 1420 50 1000 800 1730 1410
12 1450 2500 2050 62 1250 1000 2160 1760
14 2000 3460 2820 75 1400 1120 2420 1980
16 2600 4500 3670 100 2000 1600 3460 2820
18 3300 5710 4660 150 2500 2000 4330 3530

Lifting capacities are calculated with a safety coefficient.

l The lifting hook should be attached to the central part of the rope or sling; if the hook is attached near the ends of the rope/
sling, this could cause the load to slip during lifting.
l Never lift a heavy load using a single rope; always use two or more symmetrically arranged ropes.
DANGER
Suspension of a load from a single rope could cause the load to start rotating and consequently cause the rope
strands to untwist or the load to slip; this could lead to serious injury.

l Never lift a heavy load when the two legs of the ropes form a wide angle. The permitted load (kg) decreases in inverse propor-
tion to the angle of suspension; the table below indicates how the permitted load varies according to the angle of suspension
for two Ø 10 mm ropes each with a load capacity of 1000 kg.

0-4
Introduction

Fig. 1

0.1.5 - Tightening torques

Screws and nuts
DANGER
The tightening torques for certain specific components and special tightening methods are indicated in the relative
assembly headings.

The tightening torques indicated below refer to screws and nuts assembled without lubrication and, where applicable, with anaerobic
threadlocking compound. the values apply to tightening on steel or cast iron components; for soft materials such as aluminium, cop-
per, plastic, sheet metal or panels, the indicated tightening torques must be reduced by 50%.
Table 2
SCREW SIZE SCREW CLASS
8.8 10.9 12.9
Nm lb.ft. Nm lb.ft. Nm lb.ft.
M6x1 8.0 - 8.8 5.9 - 6.5 11.8 - 13.0 8.7 - 9.6 13.8 - 15.2 10.2 - 11.2
M8x1.25 19.4 - 21.4 14.3 - 15.8 28.5 - 31.5 21.0 - 23.2 33.3 - 36.9 24.5 - 27.2
M10x1.5 38.4 - 42.4 28.3 - 31.2 56.4 - 62.4 41.6 - 46.0 67.4 - 74.4 49.7 - 54.8
M12x1.75 66-5 - 73-5 49.0 - 54.2 96.9 - 107 71.4 - 78.9 115 - 128 84.8 - 94.3
M14x2 106 - 117 78.1 - 86.2 156 - 172 115.0 - 126.8 184 - 204 135.6 - 150.3
M16x2 164 - 182 120.9 - 134.1 241 - 267 117.6 - 196.8 282 - 312 207.8 - 229.9
M18x2.5 228 - 252 168.0 - 185.7 334 - 370 246.2 - 272.7 391 - 432 288.2 - 318.4
M20x2.5 321 - 355 236.6 - 261.6 472 - 522 347.9 - 384.7 553 - 611 407.6 - 450.3
M22x2.5 441 - 487 325.0 - 358.9 647 - 715 476.8 - 527.0 751 - 830 553.5 - 611.7
M24x3 553 - 611 407.6 - 450.3 812 - 898 598.4 - 661.8 950 - 1050 700.2 - 773.9
M27x3 816 - 902 601.4 - 664.8 1198 - 1324 882.9 - 975.8 1419 - 1569 1045.8 - 1156.4
FINE M8x1 20.8 - 23.0 15.3 - 17.0 30.6 - 33.8 22.6 - 24.9 35.8 - 39.6 26.4 - 29.2
M10x1.25 40.6 - 44.8 29.9 - 33.0 59.7 - 65.9 44.0 - 48.6 71.2 - 78.6 52.5 - 57.9
M12x1.25 72.2 - 79.8 53.2 - 58.8 106 - 118 78.1 - 87.0 126 - 140 92.9 - 103.2
M12x1.5 69.4 - 76.7 51.1 - 56.5 102 - 112 75.2 - 82.5 121 - 134 89.2 - 98.8
M14x1.5 114 - 126 84.0 - 92.9 168 - 186 123.8 - 137.1 199 - 220 146.7 - 162.1
M16x1.5 175 - 194 129 - 143 257 - 285 189.4 - 210.0 301 - 333 221.8 - 245.4
M18x1.5 256 - 282 188.7 - 207.8 375 - 415 276.4 - 305.9 439 - 485 323.5 - 357.4
M20x1.5 355 - 393 261.6 - 289.6 523 - 578 385.5 - 426.0 611 - 676 450.3 - 498.2
M22x1.5 482 - 532 355.2 - 392.1 708 - 782 521.8 - 576.3 821 - 908 605.1 - 669.2
M24x2 602 - 666 443.7 - 490.8 884 - 978 651.5 - 720.8 1035 - 1143 762.8 - 842.4

0-5
 Introduction
Fittings
The tightening torques indicated below refer to fittings assembled on any material.
Table 3
MET- Straight end fittings “T” end fittings “L” end fittings 90° end fittings
RIC

Thread Wrench Torque Nm Wrench Torque Nm Wrench Torque Nm Wrench Torque Nm

±10% ±10% ±10% ±10%
M10x1.25 17 14 14 14 14 14 14 14
19 14 17 14 17 14
M12x1.25 19 30 17 30 17 30 17 30
M14x1.5 19 40 19 40 19 40 19 40
M16x1.5 22 48 22 48 22 48 22 48
M18x1.5 24 58 24 58 24 58 24 58
M20x1.5 27 65 27 65 27 65 27 65
M22x1.5 30 73 30 73 30 73 30 73
M26x1.5 36 95 36 95 36 95 36 95
M27x2 36 100 36 100 36 100 36 100
M33x2 41 160 41 160 41 160 41 160
M42x2 50 250 50 250 50 250 50 250
M48x2 60 305 60 305 60 305 60 305
G 1/8” 17 13 14 13 14 13 14 13
19 13
G 1/4” 19 37 19 37 19 37 19 37
22 37
G 3/8” 24 53 24 53 24 53 24 53
G 1/2” 27 73 27 73 27 73 27 73
30 73
G 3/4” 36 100 36 100 36 100 36 100
G 1” 41 160 41 160 41 160 41 160
46 160
G 1 1/4” 50 250 50 250 50 250 50 250
G 1 1/2” 60 305 60 305 60 305 60 305
Plugs
Table 4
Hex plugs Threaded plugs with hex socket head

Thread Wrench Torque Nm ±10% Wrench Torque Nm ±10%

0-6
Introduction
MET- M6x1 10 10 - -
RIC M8x1 13 12 - -
M10x1 13 14 5 14
M10x1.25 13 14 - -
M10x1.5 13 14 - -
M12x1.25 17 30 - -
M12x1.5 17 30 6 30
M12x1.75 17 30 - -
M14x1.5 19 40 6 40
M14x2 19 40 - -
M16x1.5 22 48 8 48
M16x2 22 48 - -
M18x1.5 17 58 10 58
M18x2.5 17 58 - -
M20x1.5 19 65 - -
M22x1.5 - - 12 73
M24x1.5 22 80 12 80
M24x2 22 80 - -
M27x2 22 100 - -
M28x1.5 - - 17 110
M30x1.5 22 130 - -
M32x1.5 - - 19 150
M35x1.5 - - 22 180
M40x1.5 - - 24 225
G 1/8” 14 13 - -
G 1/4” 19 37 - -
G 3/8” 22 53 - -
G 1/2” 19 73 - -
G 5/8” 22 85 - -
G 3/4” 22 100 - -
G 1” 22 160 - -
Fittings with seal at 37°
Table 5

Thread Wrench Torque Nm ±10%

7/16” - 20 14 13
1/2” - 20 16 19
9/16” - 18 17 28
3/4” - 16 22 47
7/8” - 14 27 76
1 1/16” - 12 32 110
36 110
1 3/16” - 12 36 138
1 5/16” - 12 38 155
1 5/8” - 12 50 215
1 7/8” - 12 60 290
2 1/2” - 12 75 345

0-7
 Introduction
Fittings for pipes with banjo union
These tightening torques refer to tightening the fitting with new copper sealing washers.
Table 6
Unions for one-way fittings Unions for three-way fittings Unions for four-way fittings

Thread Wrench Torque Nm Wrench Torque Nm Wrench Torque Nm

±10% ±10% ±10%
M8x1 - 12 14 - -
M8x1.25 13 14
M10x1 - - 14 20 14 20
M10x1.25 13 20 - - - -
M12x1.25 17 30 - - - -
M12x1.5 - - 17 30 17 30
M14x1.5 19 40 19 40 19 40
M16x1.5 22 48 22 48 22 48
M18x1.5 22 58 24 58 24 58
M20x1.5 27 65 - - - -
M22x1.5 – – 27 73 27 73
M24x1.5 32 80 – – – –
M26x1.5 – – 32 95 32 95
M28x1.5 36 110 – – – –
M30x1.5 – – 36 130 36 130
M35x2 41 180 – – – –
M38x1.5 – – 46 200 46 200
M42x2 50 250 – – – –
M45x1.5 – – 55 280 55 280
M50x2 60 320 – – – –
M52x1.5 – – 60 320 60 320
M65x2 – – 75 450 75 450

0.1.6 - Threadlockers, adhesives, sealants and lubricants

Table 7
FUNCTION NAME DESCRIPTION
THREADLOCKER Loctite 222 Colour: opaque fluorescent Anaerobic product suitable for low-strength locking of retaining,
purple adjustment and precision fasteners. All traces of lubricant must
first be removed using the specific activator.
Loctite 242 Colour: fluorescent blue Anaerobic product that prevents loosening of all types of nut and
bolt; used in place of conventional mechanical locking systems.
Used for medium-strength locking. All traces of lubricant must
first be removed using the specific activator.
Loctite 243 Colour: opaque fluorescent Alternative product to 242 ; oil tolerant and so can be used on
blue lightly lubricated surfaces without prior use of activator.
Loctite 270 Colour: fluorescent green Anaerobic product for high-strength locking of bolts and studs
that do not normally require disassembly. Parts must be heated
to approximately 80°C for removal. All traces of lubricant must
first be removed using the specific activator.

0-8
Introduction
DEGREASERS Loctite 703 Product used for degreasing and cleaning parts prior to applica-
AND ACTIVATORS tion of Loctite anaerobic products; after drying, promotes uniform
curing of threadlockers
Loctite 747 Product used specifically for treatment of passive metals prior to
use of slow-cure anaerobic threadlockers (series 5 and 6). Can
also be used to increase cure speed at low temperatures or in ap-
plications where there are large gaps between the parts.
SEALANTS (for Loctite 510 Colour: red Super-rapid anaerobic sealant for sealing between rigid metal
faces and fittings) faces; can eliminate the need for conventional gaskets as it can
fill gaps up to 0.4 mm. Does not shrink and therefore fasteners
do not need re-tightening to specified torque values after curing.
Loctite 542 Colour: brown Anaerobic product used as a liquid sealant for threaded fittings
up to 3/4” gas; rapid curing and parts may be disassembled with
ordinary tools.
Loctite 554 Colour: red Anaerobic sealant and locking compound used for sealing cool-
ing and industrial fluid circuits. Slow curing, also suitable for use
on non-ferrous alloys
Loctite 572 Colour: white Anaerobic sealant and locking compound used for sealing pipes
and threaded fittings up to 2” in diameter. Very slow curing on
most metal surfaces.
Loctite 573 Colour: green Thixotropic anaerobic product used for sealing joints between
metal faces. Ensures total contact between surfaces with maxi-
mum tolerance of 0.10 mm, filling microvoids caused by flatness
errors. Very slow curing on most metal surfaces and requires
prior application of an activator.
Loctite 576 Colour: brown Anaerobic product used as a liquid thread sealant for large diam-
eter threaded fittings (up to 2”). Very slow curing; also suitable for
non-ferrous alloys and parts requiring subsequent removal.
INSTANT ADHE- Loctite 401 Colour: colourless Cyanoacrylate instant adhesive suitable for bonding a wide range
SIVES of acidic and porous materials including, ceramics, wood, rub-
ber and plastic (excluding polyolefin). Curing takes place in a few
seconds as an effect of the condensed humidity present on the
surfaces to be bonded, and is independent of environmental con-
ditions.
Loctite 495 Colour: colourless Cyanoacrylate instant adhesive suitable for bonding a rubber,
plastics and metal in any combination.
SILICONE SEAL- Silastic 738 (Dow Corning) Colour: milky One-part silicone adhesive/sealant, non shrinking, ready for use.
ANTS white Cures on exposure to air to form a rubbery solid and obviates the
need for conventional seals on flexible joints, filling gaps of up to
1 mm or more.
Dirko Transparent Colour: transparent One-part silicone adhesive/sealant, shrinking, ready for use.
Cures rapidly when exposed to humidity in the air to form a rub-
bery solid; resistant to high temperatures.
POLYURETHANE Betaseal HV3 (Gurit Essex) Colour: black Polyurethane prepolymer based adhesive/sealant, high viscosity,
SEALANTS suitable for permanent, high-strength flexible bonding. Slow cur-
ing, used for bonding glass to frames, wire mesh, metal plates,
etc. surfaces must be degreased with primer.

0-9
 Introduction
RETAINING COM- Loctite 601 Colour: fluorescent green Anaerobic, fast-curing, high-strength adhesive. Suitable for seal-
POUNDS ing and retaining cylindrical assemblies with gap clearances of
up to 0.10 mm; used for retaining rotors, gears, bearings, pulleys,
bushes etc. on shafts.
Loctite 638 Colour: fluorescent green Anaerobic structural adhesive, quick-curing, very high strength;
suitable for bonding cylindrical parts in non-ferrous alloys.
Loctite 648 Colour: fluorescent green Anaerobic structural adhesive, quick-curing, high-strength; suit-
able for bonding cylindrical parts, permanent retention of thread-
ed parts, sealing of refrigeration systems, retention of bearings,
etc. Alternative to Loctite 601 in high-temperature applications.
Loctite 986/AVX Colour: fluorescent red Anaerobic sealant/retaining compound for metal cylindrical parts.
Slow-curing, high-strength, heat-resistant and resistant to chemi-
cal attack. Parts must be first treated with an activator.
LUBRICANTS Grease (NLGI 2 EP ASTM D217: 265/295) Multi-purpose Lithium grease used for lubrication of seals, to pre-
vent oxidation and to facilitate assembly operations.
Molikote (Dow Corning) Anti-wear compound, contains Molybdenum bisulphate, used
neat or diluted with engine oil for assembly of main engine bear-
ings.
Vaseline Neutral pH compound used to protect battery terminals against
oxidization and corrosion.
Engine oil 10W - 30 Used to dilute Molikote anti-wear lubricant during assembly of
main engine bearings.

0.1.7 - Conversion factors

Conversion from British to metric units
Table 8
inch x 25.40 = mm
foot x 0.305 =m
yard x 0.914
Brit.miles x 1.609 = km
Sq.in. x 6.452 = cm²
Sq.ft. x 0.093 = m²
Sq.yard x 0.835
Cu.in. x 16.39 = cm³
Cu.ft. x 28.36 = m³
Cu.yard x 0.763
Imp.gall. x 4.547 = litres
US gall. x 3.785
pint x 0.568
quart x 1.137
US.gpm x 3.785 = ,/min
oz. x 0.028 = kg
lb. x 0.454
lb.ft. x 0.139 = kgm
lb.in. x 17.87 = kg/m
psi x 0.070 = kg/cm²
lb./Imp.gall x 0.100 = kg/,
lb./US.gall x 0.120
lb./cu.ft. x 16.21 = kg/m³
lb.ft. x 1.356 = Nm
psi x 1.379 = bar
Conversion from British to metric units
Table 9
mm x 0.0394 = inch
m x 3.281 = foot
m x 1.094 = yard
km x 0.622 = Eng.miles
cm² x 0.155 = Sq.in.
m² x 10.77 = Sq.ft.

0-10
Introduction
m² x 1.197 = Sq.yard
cm³ x 0.061 = Cu.in.
m³ x 0.035 = Cu.ft
m³ x 1.311 = Cu.yard
litres x 0.220 = Imp.gall.
litres x 0.264 = US gall.
litres x 1.762 = pint
litres x 0.880 = quart
,/min x 0.2642 = US.gpm
kg x 35.25 = oz.
kg x 2.203 = lb.
kgm x 7.233 = lb.ft.
kg/m x 0.056 = lb.in.
kg/cm² x 14.22 = psi
kg/, x 10.00 = lb./Imp.gal.
kg/, x 8.333 = lb./US.gal.
kg/m³ x 0.062 = lb./cu.ft.
Nm x 0.737 = lb.ft.
bar x 14.503 = psi

0-11
 Introduction

PAGE LEFT INTENTIONALLY BLANK

0-12
10 - Technical
characteristics

10-1
 Technical characteristics
10.1 - Engine
10.1.1 - Components of the 2012 2V UPS engine
Engine type
These instructions concern the following engine types:
l TCD 2012 L04 2V
l TCD 2012 L06 2V
l TCD 2013 L04 2V
l TCD 2013 L06 2V
l TD 2012 L04 2V m
l TCD 2012 L04 2V m
l TCD 2013 L04 2V m
Table 10
TCD
T Turbocharger
C Turbocharging air radiator
D Diesel
Table 11
2012/2013
2012 Series
2013 Series
Table 12
L04/L06
L In series
04 Number of cylinders
06 Number of cylinders
Table 13
2V
2V Number of valves
Table 14
m
m Mechanical injection system
Nozzle line pump
Exhaust gas emission regulation
The engines in this manual comply with the following regulations on exhaust gas emissions:
l EU Level IIIA
l USA EPA Tier III
Plate
Model plate
The engine type A, the engine number B and the data concerning the power are
engraved on the plate.
Each spare part order must include the engine type and number.

Fig. 2

10-2
Technical characteristics
Location of the model plate
Plate C is fixed on the cylinder head cowling or on the crankcase.

Fig. 3

Engine number
The engine number D is punched on the crankcase (arrow) and on the model
plate.

Fig. 4

Cylinder numbering
Cylinder layout
The cylinders are numbered progressively from (1) from the flywheel side.
Direction of rotation
View from flywheel side.
Left hand rotation: Anticlockwise.
Engine sides
View from flywheel side.

Fig. 5

10-3
 Technical characteristics
Illustration of the 2012 2V UPS engine
View from right hand side (example)

Fig. 6
Key:
1. Crankcase breather
2. Lubricant oil filler cap
3. Injection pump
4. Lubricant oil dipstick
5. Lubricant oil radiator
6. Lubricant oil cartridge filter
7. Lubricant oil drain screw
8. Fuel cartridge filter
9. V-belt
10. Alternator

10-4
Technical characteristics
View from left hand side (example)

Fig. 7
Key:
1. Combustion air intake
2. Coolant outlet
3. Coolant inlet
4. Supply air radiator connections
5. Exhaust gas outlet
6. Starter

10-5
 Technical characteristics
Lubrication oil system

Fig. 8
Key: (Example)
1. Lubricant oil sump
2. Lubricant oil pump
3. Pressure relief valve TD/TCD 2013
4. Lubricant oil radiator
5. Check valve TD/TCD 2012
6. Bypass valve
7. Bypass valve
8. Pressure regulator valve
9. Lubricant oil filter
10. Primary lubricant oil channel
11. Piston cooling nozzle
12. Rocker
13. Exhaust gas recirculation with internal connection TCD 2012/2013L06
14. Turbocharger
15. Air compressor

10-6
Technical characteristics
Coolant diagram (example)

Fig. 9
Key: (Example)
1. Cooler
2. Coolant inlet
3. Coolant pump
4. Recirculated portion of the coolant to the lubricant oil cooler
5. Lubricant oil radiator
6. Coolant feed line for engine cooling
7. Cylinder sleeve/head cooling
8. Fitting for cab heater
9. Heat exchanger
10. Return line
11. Coolant return to the thermostat
12. Coolant outlet
13. Compensation line
14. Breather line

10-7
 Technical characteristics
10.1.2 - Test data and settings
T00 81
1. Cylinder and side view
4-cylinder
A = curve side B = control side
A

1 2 3 4

© 39619-1

Fig. 10

T01 63
1. Valve clearance setting
4-cylinder
Firing order: 1 - 3 - 4 - 2
Table 15

Valves Cylinders
set 1 3 4 2
at overlap 4 2 1 3
angle
1 2 3 4

NOTE
“Valve overlap” means that while the intake valve starts to
© 46608-0
open the exhaust valve starts to close. Fig. 11

T01 63
Valve clearance setting
6 cylinders
Firing order: 1 - 5 - 3 - 6 - 2 - 4
Table 16
Valves Cylinders
set 1 5 3 6 2 4
at overlap 6 2 4 1 5 3
angle

NOTE
“Valve overlap” means that while the intake valve starts to open the exhaust valve starts to close.

10-8
Technical characteristics
10.1.3 - Tightening requirements 2012 2V UPS engine
Table 17
Designation Screw type Indications/notes Tightening Retightening
value/pre- value
load value
Clamping support on engine Nut screw 70 Nm
mount
Clamping support on assembly 90 Nm
stand adaptor
Feet/engine mount on crank- 260 Nm
case
Support, engine mount on M12x35-10.9 95 Nm
crankcase M12x40-10.9
M12x55-10.9
M12x60-10.9
M12x75-10.9
M12x85-10.9
M12x90-10.9
M12x220-10.9
Support, engine mount on M16x40-10.9, 260 Nm
crankcase M16x45-10.9,
M16x50-10.9,
M16x75-10.9,
M16x85-10.9,
M16x105-10.9,
M16x110-10.9,
M16x140-10.9,
M16x155-10.9,
M16x220-10.9.
Cylinder head on the crankcase Observe the tightening sequence. 30 Nm +80 Nm +90°
Lightly oil the screws.
Sealing surfaces free of oil. In the case of written
certification, the cylindrical head screws can be
used a maximum of 3 times, otherwise replace
them each time they are removed.
Rocker support on the cylinder Assembly instructions: Adjust the rocker sym- 21 Nm
head metrically to the central valve axis.
Cylindrical head screw.
Valve clearance adjustment 20 Nm
screw check nut
Casing on the cylinder head M6 11 Nm
Main bearing on the crankcase M14x1, 5x140- In the case of written certification, the cylindri- 50 Nm +90° +90°
10.9 cal head screws can be used a maximum of 3
times, otherwise replace them each time they
are removed
Bearing cover on the connect- Comply with the assembly instructions. Lightly 30 Nm +60° +30°
ing rod drum oil the screws.
Use new screws
Hole blanking screw (mass 9 Nm
compensation shaft) on the
crankcase
Front cover of the crankcase Observe the tightening sequence. 3 Nm +21 Nm
Lubricant oil sump of the crank- Observe the tightening sequence. 30 Nm
case Note that the screws are of different lengths.
Lubricant oil sump hole blank- M18x1.5 Use a Cu seal ring. 55 Nm
ing screw
Crankcase bleed screw on the 21 Nm
cylinder head casing

10-9
 Technical characteristics
Designation Screw type Indications/notes Tightening Retightening
value/pre- value
load value
Hose clip for the return line 13 Nm
Return line on the check valve Hollow screw 30 Nm
Check valve on the crankcase 80 Nm
Crankcase connector box M12x80 Observe the tightening sequence. 99 Nm
M12x150
Crankcase connector box M16x75 Observe the tightening sequence. 243 Nm
M16x140
Connection box casing 9 Nm
Gear case on crankcase M16x60-10.9 Observe the tightening sequence. 70 Nm
Gear case on crankcase M8x35-10.9 Observe the tightening sequence. 30 Nm
M8x45-10.9
M8x50-10.9
Cover on the gear case (hy- M8x55-10.9 21 Nm
draulic pump actuation)
Gear case/crankcase speed 17 Nm
regulator
Engine block on the crankcase 21 Nm
Crankcase adjustment rod 10 Nm
Speed regulator/supply air line Hollow screw 18 Nm
pilot line
Exhaust pipe on the cylinder M8 Nut on the stud bolt. 25 Nm
head Nut on the stud bolt.
Stud screw on cylinder head M10/M8x72 15 Nm
short or long
Turbocharger on the exhaust Nut 20 Nm
pipe Stud screw Use new stud bolts. Insert them with the assem- 8 Nm
bly product DEUTZ AP 1908.
Supply air line on the cylinder M6x75-10.9 11 Nm
head M6x95-10.9
Heater to charge air duct M8x100-10.9 tighten crosswise 3 Nm 30 Nm
M8x140-10.9
Turbocharging air line manifold M8x30-10.9 30 Nm
M8x95-10.9
Flexible pipe connection on the M8x30-10.9 30 Nm
turbocharging manifold
Tightening bracket, injection 16 Nm
valve on the cylinder head
Injectors, tightening nut 35 Nm
Injection valve/injection pump Comply with the assembly instructions. 25 Nm
lines
Crankcase injection pump Comply with the assembly instructions. 5 Nm 150°
Fuel supply pump on the sup- M8x25-10.9 22 Nm
port
V-belt pulley on the fuel supply 27 Nm
pump
Fastening of the fuel pipes Hose clips 30 Nm
Fuel pipe on the fuel filter con- Hollow screw 39 Nm
sole
Fuel pipe on the fuel supply D12 hollow 49 Nm
pump screw
Fuel filter console on the lubri- 30 Nm
cating oil radiator casing
Fuel filter (slip-on filter) Oil the seal lightly. Tighten clockwise. 25 Nm
Oil filter (slip-on filter) Oil the seal lightly. Tighten clockwise. 25 Nm
Oil filter (interchangeable filter) Oil the seal lightly. Tighten clockwise. Manual tight-
ening 15- 17
Nm

10-10
Technical characteristics
Designation Screw type Indications/notes Tightening Retightening
value/pre- value
load value
Oil pump oil intake pipe. Oil in- M8x25 M8x16 21 Nm
take pipe support on the crank-
case
Lubricant oil filler cap on the lu- 38 Nm
bricant oil sump
Lubricant oil filler cap on the 30 Nm
crankcase mount
Lubricant oil pipe on the turbo- Hollow screw 18 Nm
charger
Lubricant oil pipe (turbocharger) Hollow screw 34 Nm
on the crankcase
Pipe sleeve (oil return) on the 22 Nm
turbocharger
Lubricant oil and oil return pipe 13 Nm
hose clip
support bracket (oil return) on 21 Nm
the crankcase
Oil radiator casing on the crank- Note that the screws are of different lengths. 30 Nm
case Pay attention to the tightening sequence.
Oil radiator on the oil radiator M8x20-10.9 Insert the new gaskets with the assembly prod- 22 Nm
casing uct.
Observe the tightening sequence
Oil pressure switch sensor on 40 Nm
the oil radiator casing
Thermostat casing on the cylin- M10x85-10.9 70 Nm
der head
Fan console/thermostat casing 30 Nm
outlet
Coolant pump on the crankcase 30 Nm
V-belt pulley on the coolant 30 Nm
pump
Temperature transmitter on the 24 Nm
cylinder head
Fan console on the crankcase 30 Nm
Fan drive on the fan console 60 Nm
Flywheel on the crankshaft M10x30 Observe the tightening sequence. 30 Nm +60 ° +30 °
M10x35 Use new screws. Oil lightly. 30 Nm +60 ° +60 °
M10x40
M10x45M10x
50 M10x55
M10x60
M10x70
M10x75
M10x80
M10x85
Torsional vibration damper/trap- M16x1.5 Use new screws 40 Nm +60 ° +60 °
ezoidal grooved pulley on the Oil slightly.
crankshaft
V-belt pulley on the trapezoidal M12x25-10.9 130 Nm
grooved pulley
V-belt pulley on the trapezoidal M10x20-10.9 70 Nm
grooved pulley
Flange hub for the viscous cou- M12x40-10.9 110 Nm
pling joint on the torsional vibra-
tion damper

10-11
 Technical characteristics
Designation Screw type Indications/notes Tightening Retightening
value/pre- value
load value
Belt tensioner on the fan con- 80 Nm
sole
Pipe screwing D6 M10x1 ban- 6mm pipe annular part 29 Nm
jo bolt
Pipe screwing D8 M12x1-5 8mm pipe annular part 39 Nm
banjo bolt
Pipe screwing D10 M 14x1-5 10mm pipe annular part 49 Nm
banjo bolt
Hose clip, fastening M6 13 Nm
Hose clip, cable bundle fasten- M8 30 Nm
ing
Starter on crankcase M10x38-10.9 60 Nm
M8 nut 40 Nm
Stud screw 60 Nm
Alternator on the console (V- M8-10.9 M10- 30 Nm 60 Nm
belt) 10.9
Alternator on the tightening 30 Nm
bracket (V-belt)
Tightening bracket on the crank- 30 Nm
case (toothed belt)
Cable attachment on the heat- Retain the hexagon Retain the negative pole 20 Nm
er. Earth cable on the negative
pole, heater

10-12
Technical characteristics
10.2 - Transmission
10.2.1 - Transmission (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 410 -> ZK-
DW470200TD30001)
Introduction
This tractor series can be supplied in a version with 5 synchronised speeds and 4 ranges (20 FWD + 20 REV).
The rear transmission casing also houses the drive train for the rear P.T.O., which is supplied in the following versions which is sup-
plied in the following versions:
1. 2-speed P.T.O. (540 - 1000)
2. 4-speed P.T.O. (540 - 540E - 1000 - 1000E)
3. Groundspeed P.T.O. supplied with the versions of points 1 and 2.
All P.T.O. versions are mechanical with unsychronised gears and electrohydraulic engagement control, while the Groundspeed P.T.O.
is engaged by means of a mechanical control.
Main assemblies

Fig. 12 - Main assemblies

1. Clutch housing
2. Hi-Lo unit
3. Gearbox, reverse shuttle, underdrive and ranges assembly
4. Differential unit
5. Rear P.T.O.
Description
Transmission is dirven by the combustion engine and the gearbox (4) transmits drive to the bevel gear pair (5) via the clutch assembly
(1), the gear and shuttle assembly (2), and the Hi-Lo unit (3). Drive is then transmitted to final drive reduction units (6) and then to
wheels (7). Between bevel gear pair (5) and final drive reduction unit (6) is installed braking device (8) that acts as the main service
brake, while the parking brake is fitted on the 4WD output shaft (9).

10-13
 Technical characteristics

Fig. 13 - Power flow diagram

Clutch housing

10-14
Technical characteristics

Fig. 14 - Clutch housing

1. Rear P.T.O. drive shaft
2. Steering wheel
3. 12” main clutch disk
4. Main clutch thrust bearing
5. Main clutch sleeve
6. Sleeve support
7. Gearbox drive shaft
8. Main clutch lever
9. Reaction pin
10. Clutch piston

10-15
 Technical characteristics
Shuttle gearbox assembly

Fig. 15 - Shuttle gearbox assembly

1. Cover
2. Gearbox support
3. Reverse driving gear
4. Shuttle synchronizer
5. Forward driving gear
6. Gearbox input shaft
7. Main shaft
8. Secondary shaft
9. 5th speed driven gear
10. 4th-5th speed synchronizer
11. 4th speed driven gear
12. 3rd speed driven gear
13. 2nd-3rd speed synchronizer
14. 2nd speed driven gear
15. 1st speed driven gear
16. 1st speed synchronizer

10-16
Technical characteristics
Bevel pinion and range gearbox assembly

2 3 4

1
V L

9
N SR

D0036342
8 7 6 5

Fig. 16 - Bevel pinion and range gearbox assembly

1. High-Low range synchronizer
2. Lo-creeper range idler gear
3. 4WD drive gear
4. Pinion
5. 4WD driven gear
6. Creeper range driven gear
7. Medium or creeper range selector
8. Medium-low range idler gear
9. 4WD shaft

10-17
 Technical characteristics
Four-wheel drive engagement and parking brake assembly

Fig. 17 - Four-wheel drive engagement and parking brake assembly

1. Sleeve
2. 4WD output hub
3. 4WD selector fork
4. Parking brake cam
5. Parking brake lever
6. 4WD engagement lever
7. Friction shoe
8. Steel disc
9. Spacer
Differential unit

1 2

11 12 13 14 15 16 17
3

10

D0025200

8 7 6 5

Fig. 18 - Differential unit

10-18
Technical characteristics
1. Pinion
2. Pinion bearing
3. Differential carrier
4. Differential cage
5. Differential lock sleeve
6. Side gear
7. Planet pinion
8. Differential carrier
9. Side gear
10. Differential crown wheel
11. Spring
12. Spacer
13. Spring pin
14. Rod
15. Differential lock fork
16. Spring
17. Piston
Brakes and rear axle assembly

Fig. 19 - Brakes and rear axle assembly

1. Half-shaft
2. Dust seal
3. Oil seal
4. Bearing
5. Bearing
6. Ring gear
7. Pin (Qty. 3)
8. Brake cylinder
9. Piston
10. Friction disc
11. Half-shaft
12. Planet pinion
13. Planet carrier

10-19
 Technical characteristics
10.2.2 - Transmission (AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 420 -> ZK-
DW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001)
Introduction
This tractor series can be supplied in a version with 5 synchronised speeds and 4 ranges (20 FWD + 20 REV).
The rear transmission casing also houses the drive train for the rear P.T.O., which is supplied in the following versions which is sup-
plied in the following versions:
1. 2-speed P.T.O. (540 - 1000)
2. 4-speed P.T.O. (540 - 540E - 1000 - 1000E)
3. Groundspeed P.T.O. supplied with the versions of points 1 and 2.
All P.T.O. versions are mechanical with unsychronised gears and electrohydraulic engagement control, while the Groundspeed P.T.O.
is engaged by means of a mechanical control.
Main assemblies

Fig. 20 - Main assemblies

1. Clutch housing
2. Hi-Lo unit
3. Gearbox, reverse shuttle, underdrive and ranges assembly
4. Differential unit
5. Rear P.T.O.
Description
Transmission is dirven by the combustion engine and the gearbox (4) transmits drive to the bevel gear pair (5) via the clutch assembly
(1), the gear and shuttle assembly (2), and the Hi-Lo unit (3). Drive is then transmitted to final drive reduction units (6) and then to
wheels (7). Between bevel gear pair (5) and final drive reduction unit (6) is installed braking device (8) that acts as the main service
brake, while the parking brake is fitted on the 4WD output shaft (9).

10-20
Technical characteristics

Fig. 21 - Power flow diagram

Clutch housing

10-21
 Technical characteristics

Fig. 22 - Clutch housing

1. Rear P.T.O. drive shaft
2. Steering wheel
3. 13” transmission clutch disk
4. Main clutch thrust bearing
5. Main clutch sleeve
6. Sleeve support
7. Gearbox drive shaft
8. Main clutch lever
9. Reaction pin
10. Clutch piston

10-22
Technical characteristics
Shuttle gearbox assembly

Fig. 23 - Shuttle gearbox assembly

1. Cover
2. Gearbox support
3. Reverse driving gear
4. Shuttle synchronizer
5. Forward driving gear
6. Gearbox input shaft
7. Main shaft
8. Secondary shaft
9. 5th speed driven gear
10. 4th-5th speed synchronizer
11. 4th speed driven gear
12. 3rd speed driven gear
13. 2nd-3rd speed synchronizer
14. 2nd speed driven gear
15. 1st speed driven gear
16. 1st speed synchronizer

10-23
 Technical characteristics
Bevel pinion and range gearbox assembly

Fig. 24 - Bevel pinion and range gearbox assembly

1. High-Low range synchronizer
2. Lo-creeper range idler gear
3. 4WD drive gear
4. Pinion
5. 4WD driven gear
6. Creeper range driven gear
7. Medium or creeper range selector
8. Medium-low range idler gear
9. 4WD shaft

10-24
Technical characteristics
Four-wheel drive engagement and parking brake assembly

A
2

4 9 7 8 7 6 5
D0036350

A -A

Fig. 25 - Four-wheel drive engagement and parking brake assembly

1. Sleeve
2. 4WD output hub
3. 4WD selector fork
4. Parking brake cam
5. Parking brake lever
6. 4WD engagement lever
7. Friction shoe
8. Steel disc
9. Spacer
Differential unit

10-25
 Technical characteristics

1 2

11 12 13 14 15 16 17
3

10

D0047810

8 7 6 5

Fig. 26 - Differential unit

1. Pinion
2. Pinion bearing
3. Differential carrier
4. Differential cage
5. Differential lock sleeve
6. Side gear
7. Planet pinion
8. Differential carrier
9. Side gear
10. Differential crown wheel
11. Spring
12. Spacer
13. Spring pin
14. Rod
15. Differential lock fork
16. Spring
17. Piston

10-26
Technical characteristics
Brakes and rear axle assembly

6 7 8 9

1 2 3 4 5

10

12

11

D0047820

Fig. 27 - Brakes and rear axle assembly

1. Half-shaft
2. Dust seal
3. Bearing
4. Oil seal
5. Bearing
6. Ring gear
7. Brake cylinder
8. Piston
9. Friction disc
10. Half-shaft
11. Planet pinion
12. Planet carrier

10.2.3 - Transmission (AGROFARM 430 -> ZKDW550200TD30001)

Introduction
This tractor series can be supplied in a version with 5 synchronised speeds and 4 ranges (20 FWD + 20 REV).
The rear transmission casing also houses the drive train for the rear PTO, which is supplied in the following versions:
1. 2-speed PTO (540 - 1,000)
2. 4-speed PTO (540 - 540E - 1,000 - 1,000E)
3. PTO Groundspeed PTO supplied with versions described in points 1 and 2.
All PTO versions are mechanical with unsynchronised gears and electrohydraulic engagement control, while the Groundspeed PTO
is operated by a mechanical control.

10-27
 Technical characteristics
Main assemblies

1 2 3 4 5

D0036580

Fig. 28 - Main assemblies

1. Connector housing
2. Hi-Lo unit
3. Gearbox, reverse shuttle, underdrive and ranges assembly
4. Differential assembly
5. Rear PTO
Description
The transmission receives drive from the engine and transmits it through the clutch assembly (1), gearbox and shuttle assembly (2),
the Hi-Lo gearbox (3) and the range gearbox (4) to bevel gear set (5). Drive is then transmitted to the planetary reduction gearboxes
(6) and then to wheels (7). The braking device (8) acting as the main service brake is installed between the bevel gear set (5) and the
planetary reduction gearbox (6), while the parking brake is installed on the dual traction output shaft (9).

10-28
Technical characteristics
2
1
REV FW

E V L 5

6
3
N SR
7
9
D0036300
4

Fig. 29 - Power flow diagram

Connector housing

10-29
 Technical characteristics

Fig. 30 - Connector housing

1. Rear PTO drive shaft
2. Flywheel
3. 13” main clutch disk
4. Main clutch thrust bearing
5. Main clutch sleeve
6. Sleeve support
7. Transmission drive shaft
8. Main clutch lever
9. Reaction pin
10. Clutch piston

10-30
Technical characteristics
Gearbox and shuttle assembly
2

1 3 4 5 6

16 15 14 13 12 11 10 9
D0036310

Fig. 31 - Gearbox and shuttle assembly

1. Cover
2. Gearbox support
3. Reverse driving gear
4. Shuttle synchronizer
5. Forward driving gear
6. Gearbox input shaft
7. Primary shaft
8. Secondary shaft
9. 5th speed driven gear
10. 4th-5th speed synchronizer
11. 4th speed driven gear
12. 3rd speed driven gear
13. 2nd-3rd speed synchronizer
14. 2nd speed driven gear
15. 1st speed driven gear
16. 1st speed synchronizer

10-31
 Technical characteristics
Bevel drive and range gearbox assembly

2 3 4

L
1 V

9
M SR

D0047790
8 7 6 5
Fig. 32 - Bevel drive and range gearbox assembly
1. High-Low range synchronizer
2. Lo-creeper range idler gear
3. 4WD drive gear
4. Pinion
5. 4WD driven gear
6. Creeper range driven gear
7. Medium or creeper range selector
8. Medium-low range idler gear
9. 4WD shaft

10-32
Technical characteristics
Four-wheel drive engagement and parking brake assembly

A
2

4 9 7 8 7 6 5
D0036350

A -A

Fig. 33 - Four-wheel drive engagement and parking brake assembly

1. Sleeve
2. 4WD output hub
3. 4WD selector fork
4. Parking brake cam
5. Parking brake lever
6. 4WD engagement lever
7. Friction shoe
8. Steel disc
9. Shim
Differential assembly

10-33
 Technical characteristics

1 2

11 12 13 14 15 16 17
3

10

D0047810

8 7 6 5

Fig. 34 - Differential assembly

1. Pinion
2. Pinion bearing
3. Differential carrier
4. Differential case
5. Differential lock sleeve
6. Sun gear
7. Planet gear
8. Differential carrier
9. Sun gear
10. Crown wheel
11. Spring
12. Shim
13. Spring pin
14. Rod
15. Differential lock fork
16. Spring
17. Piston

10-34
Technical characteristics
Rear brakes and axle assembly

6 7 8 9 10 11

1
2 3 4 5

12

16

15 14 13

17

Fig. 35 - Rear brakes and axle assembly

1. Axle shaft
2. Dust seal
3. Bearing
4. Seal ring
5. Bearing
6. Ring gear
7. Brake cylinder
8. Park Brake operating spring
9. Piston
10. Friction disc
11. Steel disc
12. Axle shaft
13. Park Brake engagement piston
14. Flange
15. Planet gear
16. Planet gear carrier
17. Brake take-up device

10.2.4 - Rear P.T.O.

Description
The rear power take-off allows drive to be transmitted to an implement at a predetermined rotation speed. Rotary drive is taken
directly from the engine and the operator controls engagement of the P.T.O. via the pushbutton on the right-hand side of the driving
position. Engagement of the rear P.T.O. , for the speeds 540, 540 ECO, 1000 and 1000 ECO, is controlled by the P.T.O. clutch unit
and is electro-hydraulic, while it is via a mechanical control for the Groundspeed P.T.O. (for tractors fitted with this option). The P.T.O.
speed is a selected by mechanical controls.
The rear P.T.O. is supplied in 2 versions with two or four rotation speeds:
l 540-1000 P.T.O.
l P.T.O. 540 - 540 ECO - 1000 and 1000 ECO
and a further shaft can be fitted for the groundspeed P.T.O. The characteristic of the groundspeed velocity is that of being directly
proportional to the rotation speed of the rear wheels according to a fixed ratio of the P.T.O. shaft revolutions and the wheel revolutions.
Power flow diagram

10-35
 Technical characteristics

Fig. 36 - 2-speed P.T.O.

Fig. 37 - 4-speed P.T.O.

10-36
Technical characteristics
P.T.O. clutch assembly.

Fig. 38 - P.T.O. clutch assembly.

1. Hub
2. P.T.O. clutch.
3. Clutch housing
4. Body
5. P.T.O. brake clutch piston.
6. P.T.O. brake clutch.
7. P.T.O. engagement piston.
8. Piston return spring
9. Accumulator cylinder
10. Accumulator spring
11. Accumulator piston
12. Pressure relief valve

10-37
 Technical characteristics
Operation
The following text describes what happens when the P.T.O. is engaged.
l When the operator activates P.T.O. engagement, solenoid valve (1) is energized and the pressurized oil from regulator valve
(2) flows in line A.
l The pressurized oil from regulator valve (2) is thus introduced into chamber b of accumulator (3).
l As the pressure in chamber b, increases, the force exerted by the pressure on piston (4) compresses springs (5). The in-
creased stroke of piston (4) corresponds to an increase in the pressure in chamber b and chamber c of piston (6). For this
reason, the clutch engagement pressure is modulated within the range of 2 to 12 bar. Simultaneously the oil in passage d is
returned to tank and the pressure acting on piston (7) decreases, thereby allowing the hub to rotate (8).

Fig. 39 - P.T.O. engagement.

The following text describes what happens when the P.T.O. is disengaged.
l The P.T.O. is disengaged by de-energizing solenoid valve (1).
l The pressurised oil in line a is sent to the return circuit through solenoid valve (1).
l Because of the decrease in pressure in passage a, piston (4) is pushed to the right by springs (5) and force of spring (9)
pushes piston (6) to the right, bringing it to the rest position. At the same time, the pressurised oil from regulator valve (2) flows
into passage d. For this reason, the piston (7) is moved to the right, thus activating the P.T.O. brake and stopping rotation of
hub (8).

10-38
Technical characteristics

Fig. 40 - P.T.O. disengagement.

10-39
 Technical characteristics
10.2.5 - 2 and 4-speed PTO and Groundspeed PTO
2-speed PTO and Groundspeed PTO

Fig. 41 - 2-speed PTO and Groundspeed PTO

1. Drive shaft
2. Bearing
3. 1000 PTO driving gear
4. Bearing
5. Cover
6. Bearing
7. 540-1000 PTO output shaft
8. Groundspeed PTO output shaft
9. Bearing
10. 540 PTO driven gear
11. 1000 PTO driven gear
12. Bearing
13. Selector sleeve
14. Fork
15. Speed selector lever
16. Shoe

10-40
Technical characteristics
4-speed PTO and Groundspeed PTO

Fig. 42 - 4-speed PTO and Groundspeed PTO

1. PTO input shaft
2. Normal/ECO PTO selector sleeve
3. ECO PTO drive shaft
4. Flange
5. Normal PTO driving gear
6. ECO PTO driving gear
7. Bearing
8. Cover
9. Bearing
10. 540-1000 PTO. output shaft
11. Groundspeed PTO output shaft
12. Bearing
13. ECO -1000 PTO driven gear
14. 540/1000 PTO selector sleeve
15. 540 PTO driven gear
16. Bearing
17. Fork
18. Shoe
19. Normal/ECO PTO selector lever
20. 540/1000 PTO selector lever
21. Shoe
22. Fork

10-41
 Technical characteristics
10.2.6 - Hydraulic Reverse Shuttle

1 5

2 6

3 7

4 8

Fig. 43 - Description of shuttle

l 1 - Flexible coupling
l 2 – Forward drive clutch
l 3 - Forward drive hub
l 4 - Forward drive clutch housing
l 5 - Pistons
l 6 – Reverse drive clutch
l 7 – Reverse drive hub
l 8 - Reverse drive clutch housing

10-42
Technical characteristics
1 6

2
7

3 8

4 9

10

Fig. 44 - Description of clutches

l 1 - Corrugated anti-flutter springs
l 2 – Clutch friction plates (material N266)
l 3 – O-ring.
l 4 - 21 Bar pressure feed duct
l 5 - Goetze seal rings
l 6 - Piston return springs (q.ty 10)
l 7 - Intermediate thrust discs
l 8 – Intermediate discs (thickness 3 mm)
l 9 – Piston
l 10 - Lubrication duct

10-43
 Technical characteristics

Fig. 45 - Description of neutral position

l 1 - Low lubrication pressure (green)
l 2 - Forward drive clutch feed pressure = 0 bar
l 3 - Reverse drive clutch feed pressure = 0 bar

10-44
Technical characteristics

2 4

Fig. 46 - Description of forward drive position

l 1 - Low lubrication pressure (green)
l 2 - Forward drive clutch feed pressure = 21 bar
l 3 - Piston stroke 4 mm
l 4 - Reverse drive clutch feed pressure = 0 bar

10-45
 Technical characteristics

2 4

Fig. 46 - Description of reverse drive position

l 2 - Forward drive clutch feed pressure = 0 bar
l 1 - Low lubrication pressure (green)
l 4 - Forward drive clutch feed pressure = 21 bar
l 3 - Piston stroke 4 mm

10-46
Technical characteristics
10.3 - Rear axle
10.3.1 - Park Brake (AGROFARM 430 -> ZKDW550200TD30001)
The “Park Brake” (PB) is a brake system designed to perform emergency and parking braking functions and replace the conventional
handbrake.
The braking force is produced by Belleville washers exerting force on the rear brake discs. As a result, the braking capacity of the
system is dependent on the characteristics of the springs.
This is a negative action system. To release the PB, hydraulic pressure must be fed to the spring counter pistons. The emergency
braking function is obtained by reducing the PB pressure in a progressive, controlled manner, while the parking brake function is
obtained with a PB pressure of zero.

2
1

Fig. 47

10-47
 Technical characteristics
10.4 - Front axle
10.4.1 - Front axle (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 410 -> ZKD-
W470200TD30001)

X–2

1769

D0024080

Fig. 48 - Steering angle “A”

l Single-acting steering cylinders version: 50°
l Double-acting steering cylinders version: 55°

10-48
Technical characteristics
Final drive

5
4 6
3 7
2
8
1
9

22

21

20

19 10

11

12

18 17 16 15 14 13
D0036570

Fig. 49 - Final drive

1. Planet carrier
2. Oil seal
3. Ring gear
4. Brake disc
5. Steering knuckle housing
6. Upper kingpin
7. Gasket
8. Top bearing
9. Axle shaft
10. Needle roller bearings
11. Oil seal
12. Lower bearing
13. Gasket
14. Lower kingpin
15. Brake piston
16. Steel disc
17. Friction disc
18. Bearing
19. Cover
20. Protective disc

10-49
 Technical characteristics

5
4 6
3 7
2
8
1
9

22

21

20

19 10

11

12

18 17 16 15 14 13
D0036570

Fig. 49 - Final drive

21. Planet gear
22. Planet shaft

10-50
Technical characteristics
Pinion, differential and differential lock

1 2 3 4
18
5
19
7 6
23

22

21

24

20
17 8
16 3 9
D0025260

15 10

11
14
12
13

Fig. 50 - Pinion, differential and differential lock

1. Axle housing
2. Differential crown wheel
3. Planet gear
4. Sun gear
5. Differential carrier
6. Differential lock device
7. Axle shaft
8. Bearing
9. Bearing
10. Spacer
11. Bearing
12. Oil seal
13. Oil seal
14. Oil seal
15. Nut
16. Pinion
17. Differential carrier
18. Bearing
19. Sun gear
20. Differential carrier
21. Piston
22. Shock absorber spring
23. Return spring
24. Differential lock engagement lever

10-51
 Technical characteristics

1 2 3 4
18
5
19
7 6
23

22

21

24

20
17 8
16 3 9
D0025260

15 10

11
14
12
13

Fig. 50 - Pinion, differential and differential lock

25. Shoe

10-52
Technical characteristics
10.5 - Rear lift
10.5.1 - Rear lift distributor

14 13 12

P 16 15

6 T1 7 8 9 10 11

1 2 3 4 5 T

Fig. 51 - Rear lift distributor

l P - Distributor supply
l T - Return
l A - Lift control
l T1 - Return
l 1 - Relief valve
l 2 – Plug
l 3 - Rate of drop control valve spool
l 4 - Rod
l 5 - Rate of drop regulator valve spring
l 6 - Lift control spool return spring
l 7 - Lift control spool
l 8 - Check valve actuator piston
l 9 - Strut
l 10 - Check valve
l 11 - Inlet valve
l 12 - Pilot/enable valve
l 13 - Pilot/enable valve spring
l 14 – Spacer
l 15 - Enable valve spring
l 16 - Enable valve

10-53
 Technical characteristics

4 3 1
A

2
T1

T
6 5

Fig. 52 - Hydraulic circuit diagram

l P - Distributor supply
l T - Return
l A - Lift control
l T1 - Return
l 1 - Rate of drop control valve spool (Valvematic)
l 2 - Lift control spool
l 3 - Check valve
l 4 - Inlet valve
l 5 - Pilot/enable valve
l 6 - Enable valve
Operation
The function of the lift distributor is to send pressurised oil to the lift cylinder, allowing the implement to be raised or lowered.

10-54
Technical characteristics

1
6
2

Fig. 53
l 1 - Check valve
l 2 - Rate of drop control valve (Valvematic)
l 3 - Inlet valve
l 4 - Enable valve
l 5 - Pilot/enable valve
l 6 - Relief valve
Neutral position (lift not operated)
High pressure oil from the pump (1) flows into line (a).
As all paths are closed, the pressure increases until the force exerted on the enable valve (2) exceeds that of the spring (3), shifting
the valve (2) to the right and allowing oil to return to the tank.

10-55
 Technical characteristics

2 3

Fig. 54
Lowering
When the spool (4) is shifted to the right, the down stroke begins; this can be divided into two stages:

10-56
Technical characteristics

6 e

c
b
d 4

Fig. 55
Step 1:
l When the spool (4) is shifted to the right, this connects:
m line “b” with line “c”, moving piston (6) to move to the right.
m line “d” with return line “h”, reducing the pressure in line “e”.

10-57
 Technical characteristics

t n 6 e 7 8
m

Fig. 56
Step 2:
l As piston (6) moves to the right, the ball (7) is also shifted to the right, connecting the chamber m of the check valve (8) with
line e. As a result, the pressure in chamber m decreases and the force exerted on piston (6) by the pressure in chamber n
pushes valve (8) to the right and connects line p with line e, allowing oil to flow and lowering the lift. The regulator valve (9) is
used to control the rate of drop. As the valve moves downwards, it limits the flow of oil between port t and line p.
UP control
When spool (4) is moved to the left, oil is able to flow between passages (b) and (d), (f) and (g), and (a) and (e). When the force
exerted by the pressure in line (e) overcomes the pressure in chamber (m), valve (6) is shifted to the right, allowing oil to flow into line
(p), from which it then flows through valve (9) to port (t) and to the lift cylinder (10).
To increase lifting speed - in other terms, the oil flow to lift cylinder (10) - a check valve (11) is installed in parallel with spool (4), en-
suring that oil is delivered only when lifting.

10-58
Technical characteristics

t e 8

m
10

b
6 4

p
d
11
f

Fig. 57

10-59
 Technical characteristics

PAGE LEFT INTENTIONALLY BLANK

10-60
20 - Calibrations and
electronic diagnosis

20-1
 Calibrations and electronic
diagnosis
20.1 - Diagnostic tools
20.1.1 - All Round Tester (ART® SAME)
All Round Tester (ART®)
Description
To facilitate the operations of fault diagnosis, putting the vehicle into service and testing electrical components of the engine and lift,
the technician is provided with a test instrument called All Round Tester (hereinafter ART®). Using the ART® the technician can:
l display errors (faults) that have occurred;
l calibrate the sensors;
l display data detected by the electronic control units (e.g. status of the sensors) managing the systems.
Data is exchanged between the ART® and the ECUs by way of a diagnostic socket incorporated in the combine wiring. The ART® is
supplied with a number of different interface cables, which are to be selected in accordance with the type of vehicle and the methods
described in the relative workshop manual or in the CD supplied with the tester.
Description of the kit
the ART® is supplied to authorised service centres in a case containing:
l Case, complete (P/N 5.9030.730.6/30)
m 1 - All Round Tester (P/N 5.9030.730.0)
m 2 - Diagnostic cable for BOSCH EHR4 rear hydraulic lift - Diagnosis

and programming cable of electronic regulator, original type - Diag-

nostic cable for SBA system, original type (P/N 5.9030.681.3/10)
m 3 - Adapter cable for radar connector (P/N 5.9030.681.7)
m 4 - Adapter cable for wheel speed sensor connector (P/N

5.9030.681.5)
m 5 - Cable for diagnostic socket (P/N 5.9030.681.4) (As from 01/01/06
Fig. 58
the cable has been modified to allow the ART® to connect to all
control units. Contact the Technical Assistance Service for further
information)
m 6 - Adapter cable for diagnosis socket on armrest (P/N 0.011.6178.4)
m 7 - Cable for connection to diagnosis socket in engine, gearbox, and

lift ECUs zone (P/N 0.011.5445.4)

m 8 - EPROM port box (P/N 0.010.2154.2)
m 9 - CD ROM (P/N 307.1056.8/60)

*
Notes on use
The ART® is protected against battery polarity inversion and positive and negative over voltages of brief duration (1 msec). Do not
attempt to connect the ART® to any sockets other than those specifically designed for use with the tester and do not use extension
leads. The display is permanently backlit to ensure visibility on all light conditions. The knob on the side of the tester allows contrast
adjustment. If the display appears blank, it is possible that the contrast knob is positioned in such a way that the data are not visible
on the screen. The tester operates correctly at temperatures between 0 and 40°C; it is advisable to switch the tester off every 30
minutes to help prolong its service life. Before disconnecting the ART® from the diagnostic socket, turn the starter key to the “O”
(OFF) position.
Description of the tester

20-2
Calibrations and electronic
diagnosis
The ART® comprises:
1. Liquid crystal display featuring permanent backlighting
2. 16-key alphanumeric keypad
3. Contrast adjustment knob. Serves to adjust the contrast of the display. If the
display appears blank, it is possible that the contrast knob is positioned in
such a way that the data are not visible on the screen.
4. Parallel port (used to connect the ART® to systems with electronic control
units that do not have microprocessors).
5. Serial port (used to connect the ART® to systems with electronic control
units incorporating microprocessors).

Fig. 59

General notes on connecting and powering up the Tester

1. To connect the tester to the vehicle’s electronic system, proceed as follows:
2. Switch off the engine and remove the key from the starter switch;
3. Connect the ART® to a diagnostic;
4. Insert the key in the starter switch and turn it to “I” (ON).
5. On power up, the ART® will display the battery charge level test. If the volt-
age is below 10V, the ART® will not have sufficient voltage to connect to
the ECUs, while voltages in excess of 15V could damage the ART®. After
a few seconds, the tester will attempt to connect to the electronic system
and will display a screen (which may vary according to the vehicle type
or the connector to which it is connected) from which the technician can
choose to connect to an ECU and test the operation of components.

Fig. 60

Selection of the display language

1. The ART® has the possibility to display information in a number of different languages (factory setting: ITALIAN). To change
the display language, proceed as follows.
2. Switch off the engine and remove the key from the starter switch
3. Connect the ART® to a diagnostic socket
4. While holding pressed key A on the keypad, turn the starter key to “I” (ON).

20-3
 Calibrations and electronic
diagnosis
5. Enter the password 1 2 3 F.

Fig. 61
6. Press “1 - Language SEL.”.

Fig. 62
7. Press “C to change” and then the key corresponding to the desired lan-
guage. In the example above, key “2 - ENGLISH” was pressed to select
English.
Press “E EXIT” twice to quit
Turn the starter key to “O” (OFF) and disconnect the ART® from the diag-
nostic socket.

Fig. 63

20-4
Calibrations and electronic
diagnosis
Serial ports configuration
1. The vehicle electronic systems to which the ART® can be connected differ from one another and utilize different pinouts at
the diagnostic socket.
For this reason, the serial ports must first be configured so as to guarantee full compatibility of the ART® with all SAME elec-
tronic systems.
To change the configuration of the serial ports, proceed as follows.
2. Switch off the engine and remove the key from the starter switch
3. Connect the ART® to a diagnostic socket
4. While holding pressed key A on the keypad, turn the starter key to “I” (ON)
5. Enter the password 1 2 3 F.

Fig. 63
6. Press “2 - Serial Ports”.

Fig. 64
7. Enable all the serial ports by pressing “1 - Port Enable” seven times.
Press “E EXIT” twice to quit.
Turn the starter key to “O” (OFF) and disconnect the ART® from the diag-
nostic socket.

Fig. 65

20-5
 Calibrations and electronic
diagnosis
ART® - Diagnostic socket connection
ART® - Diagnostic socket connection
Table 18
Components Image From: To:
All Round Tester (ART®) - -

Fig. 66
Cable for diagnostic socket (P/N (ART®) Tractor diagnostic
5.9030.681.4); A = Connection to the socket
ART®; B = Connection to diagnostic socket

Fig. 67
Tractor diagnostic socket - -

Fig. 68

20.1.2 - SDF Analyser

SDF Analyser
Description
The SDF Analyser instrument lets the technician troubleshoot and commission the tractor correctly, and test the functions of the
electric components of the tractor’s on-board systems and engine.
Data is exchanged between the instrument and the electronic control units on the tractor via a diagnostic socket installed on the
tractor wiring harness.
The SDF Analyser lets the technician perform the following:
l View data received from the different electronic control units (e.g. sensor, button and potentiometer states etc.) managing the
tractor systems.
l Test the functions of the electric components installed on the tractor. (e.g. buttons, potentiometers, solenoid valves etc.)
l Perform the operations necessary for commissioning the tractor, calibrating the hydraulic reverse shuttle and calibrating sen-
sors.
l View errors (faults).
-

20-6
Calibrations and electronic
diagnosis
Advantages
Using the SDF Analyser offers a number of significant advantages because:
l It has a screen refresh rate two time faster than previous diagnostic systems.
l It is compatible with all laptop operating systems in use today. It is faster than the ART® (All Round Tester).
l It functions as an active interface, with its own microprocessor and flash memory. New software updates are easily installable
with a guided menu.
l It may be used on both old and new tractors, using the specific adapter cables included following the instructions given in the
relative training and workshop manuals.
l May be connected to the laptop either with a USB cable or by Bluetooth connection within a 10 metre range.
-
Description of Kit
The SDF Analyser is delivered to Authorised Service Centres in a case containing the following:
1. Complete SDF Analyser carrier case (P/N 5.9030.997.0) 6 7
2. Analyser tool (P/N 5.9030.997.1) 8
3. Base PC Tester diagnostic cable (P/N 5.9030.997.2)
4. Base EDS diagnostic cable (P/N 5.9030.997.4) 4
5. Bluetooth dongle (P/N 5.9030.997.5)
6. EDS adapter cable, first type (P/N 5.9030.997.6)
7. PC Tester adapter cable for Deutz (P/N 5.9030.997.7)
8. PC Tester adapter cable for Rubin /Iron (P/N 5.9030.997.8)
9. Case containing: 9

m CD-Rom for installing software on laptop and

10
m Multi-language handbook with installation instructions. 3 2
1 5
10. USB connection cable
Fig. 69

-
Installing the software
The minimum requisites for the laptop for installation of the SDF Analyser base
software and the PC diagnostic software are indicated in the multi-language hand-
book included in the case. The installation procedure is also described in the hand-
book. Installing the SDF Analyser software is simple and only takes a few minutes.
Once the software is installed, the icons for launching the 3 functions of the soft-
ware will be displayed on the desktop of the host laptop.

Fig. 70

-
Functions
The SDF Analyser software consists of 3 functions:
PC Tester
Generally used for connection to electronic control units on tractors with CANBUS network. There are
certain exceptions, however, which are described in detail in the specific training courses.
PCTester

CVT Diag
For connection to “Infocenter” on-board instruments.

CVT Diag

20-7
 Calibrations and electronic
diagnosis
SDF Analyser
For connection to ZF electronic control units on tractors without CANBUS network.

SDF Analyser

-
Connecting tool and launching software
Side: Tool-Tractor
Connect the SDF Analyser to the electronic system of the tractor as follows:
1. Switch the tractor off and remove the ignition key,
2. Connect the SDF Analyser interface to the correct adapter cable (in relation to tractor diagnosed), then connect the cable to
the diagnostic socket on board the tractor,
3. Turn the ignition switch to “On”.
-
Tool-Laptop side
Connect the SDF Analyser to the laptop as follows:
l Use the Bluetooth dongle to connect via Bluetooth, or
l Enable Bluetooth on your laptop (if laptop has integrated Bluetooth module), or
l Connect the SDF Analyser interface to the laptop with the USB connector cable.
-
Launching functions
To launch any of the functions, double-click the respective icon on the desktop.
-
Basic settings in PC Tester
The user may configure a number of basic settings (e.g. language, COM ports, screen layout etc.) for the PC Tester function before
starting to use the function itself. Proceed as follows:
Double-click the relative icon on the desktop and wait for the start screen.
Select “Tools” and then “Setup” from the option menu.

Fig. 71

-
Menus available:
l “Interface” / Interface,
l “Lines Selection” / Lines Selection,
l “Interface” / Interface.
-

20-8
Calibrations and electronic
diagnosis
“Interface” / Interface menu
The following may be selected from this menu:
l Interface and COM ports, and
l display language.

Fig. 72

-
“Visual Style” / Visual Style menu
The following may be selected from this menu:
l Background colour of screens,
l Font colour,
l Font type, and
l Enable “Microsoft Word” function
(reproduces PC Tester screens in a Word document.)

Fig. 73

-
“Lines Selection” / Lines Selection menu
The following may be selected from this menu:
l Tractor ECU pin mapping in manual mode.

Fig. 74

-
Base settings in SDF Analyser
The user may configure a number of basic settings for (e.g. language, COM ports, screen layout etc.) for the SDF Analyser function
before starting to use the function itself. Proceed as follows:
Double-click the relative icon on the desktop and wait for the start screen.
Select “Continue” / Continue from the options menu, then select “Configuration” /
Configuration.

Fig. 75

20-9
 Calibrations and electronic
diagnosis
“Configuration” / Configuration menu
The following may be selected from this menu:
l Interface,
l Display language,
l COM ports,
l Font type, and
l Window layout.

Fig. 76

-
SDF Analyser - Diagnostic socket
SDF Analyser - Diagnostic socket
Table 19
Components Image From: To:
SDF Analyser - -

Fig. 77
Cable for diagnostic socket (P/N SDF Analyser Tractor diagnostic
5.9030.997.2); A = Connection to SDF socket
Analyser; B = Connection to diagnostic
socket

Fig. 78
Tractor diagnostic socket - -

Fig. 78

20-10
Calibrations and electronic
diagnosis
20.1.3 - Serdia 2000
SERDIA 2000 level III” software
SERDIA 2000 level III” software
To enable correct analysis of faults, facilitate the procedure of putting the tractor into service and check correct operation of the
engine electrical components, the Technician is provided with a software application called SERDIA (P/N. 5.9030.740.4/30), for in-
stallation on a portable computer. With SERDIA, the technician can:
l display errors (faults) that have occurred;
l program the control unit;
l carry out sensor calibration or setting procedures.
Description of the kit
The SERDIA software is supplied to Authorised Workshops in a carrying case with all the basic items needed for operation. The case
contains:

Fig. 79

Table 20
Pos. Code Description Qty
5.9030.740.4/30 Case, complete 1
1 5.9030.740.0/10 . Installation disk 1
2 5.9030.740.2/10 . Level III interface, General revision + USB cable 1
3 5.9030.741.0 Adapter cable (not included in kit) 1
Data is exchanged between the SERDIA software and the control units by way of a diagnostic socket incorporated in the tractor
wiring.
Accordingly, the SERDIA package is supplied with an interface cable that must be used on the particular model and version of tractor
being serviced.

20-11
 Calibrations and electronic
diagnosis
20.2 - Diagnostic tool screens
20.2.1 - ECU interrogation
Diagnostics
Diagnostics is the set of analytical and reporting activities which, through the measurement of certain physical parameters characteri-
sing the machine monitored, provide significant information on the status of the machine itself and on how its status varies over time,
to enable the evaluation and prediction of both short and long term reliability.
How diagnostics works
When connected to the diagnostic sockets of tractors with specific cables, the All Round Tester (ART®) and SDF Analyser tools con-
nect to and interrogate the different ECUs in the machine, and display the relative data acquired on screen.
ECUs interrogated by the All Round Tester (ART®) and SDF Analyser
The All Round Tester (ART®) and SDF Analyser tools may acquire and analyse data from the following electronic control units. Rear
hitch (EKR), front suspension, HPSA, HLHP1, HLHP2, PTO, Pre-heat, Hydraulic reverse shuttle (“Smart Lever”), Transmission, ZF
transmissions (TCU/VDC, SGR/FMGR), SLH engines, Instrument CLUSTER: INFOCENTER.
WARNING
The primary diagnostic functions of Deutz-AG ECUs are performed with the Serdia 2000/Serdia 2010 diagnostic tools.

WARNING
However, certain procedures are accessible and certain information viewable also with the All Round Tester (ART®)
and SDF Analyser diagnostic tools.

How to select the ECU interrogated

All Round Tester (ART®)
1. Switch the tractor off and remove the ignition key;
2. Connect the ART® to the diagnostic socket;
3. Turn the ignition switch to “I” (ON);
4. When the ART® tool switches on, the battery charge level test screen is displayed.
WARNING
A voltage of less than 10V is insufficient for the ART® to connect to the ECUs, whereas voltages above 15V may
damage the tool itself.

5. After a few seconds, the tester attempts to connect to the electronic system of
the tractor, and displays a screen (which differs in relation to tractor model and the - - - - - - M E N U - - - - - -
diagnostic connector used) in which the technician may select which ECU to con-
nect to, and analyse functions of components.
1 - E N G I N E E C U
=> The image aside shows an example of a selection screen visible when using
2 - S M A R T L E V E R
the All Round Tester (ART®), in this case connected to the Agrofarm 115G tractor 3 - C L U S T E R
1 - “Engine ECU” / SHL Tier3a engine ECU,
2 - “Smart Lever” / Hydraulic reverse shuttle ECU integrated in “Smart Lever”
shuttle lever,
3 - “Cluster” / Digital on-board instrument cluster.

[ E ] E X I T
Fig. 80

WARNING
To change from one ECU to another, switch the tractor off, reconnect and select the new ECU.

20-12
Calibrations and electronic
diagnosis
---
SDF Analyser
1. Switch the tractor off and remove the ignition key;
2. Connect the SDF Analyser to the diagnostic socket;
3. Turn the ignition switch to “I” (ON);
4. Launch the diagnostic programme on your computer;
5. After scanning the channels, the tester attempts to connect to the electronic
system of the tractor, and displays a screen (which differs in relation to tractor
model and the diagnostic connector used) showing the technician a list of the
ECUs recognised. Press “End”.
=> The image aside shows an example of a selection screen visible when using
the SDF Analyser, in this case connected to the Dorado³ 100 tractor:
● “Cluster” / Digital on-board instrument cluster.
● “Smart Lever” / Hydraulic reverse shuttle ECU integrated in “Smart Lever” shut-
tle lever,
● “Engine ECU” / SHL Tier3a engine ECU,
Fig. 81

WARNING
To interrogate a different ECU, simply select the name of the de-
sired ECU
(the image aside shows an example of a selection screen visible when using the
SDF Analyser -
in this case connected to the Dorado³ 100 tractor).

Fig. 82

Menus available for each ECU

The number of ECUs listed varies in relation to the model of tractor the tool is connected to.
After selecting an ECU, the list of options available usually consists of either
5 choices: M E N U M E N U
1. “Monitors”/Monitor Menu: - - - - - - - - - - - - - - - -
Analyses all sensors in monitor mode. View data received from the different
electronic control units (e.g. sensor, button and potentiometer states etc.)
managing the tractor systems. 1 - M O N I T O R S
2. “Parameters”/Parameter Menu: 2 - P A R A M E T R E S
For setting certain machine options. 3 - C A L I B R A T I O N S
3. “Calibrations”/Calibration Menu: 4 - T E S T S
For calibrating the different subsystems of the machine, performing the op- 5 - A L A R M S
erations necessary for commissioning the tractor, calibrating the hydraulic
reverse shuttle and calibrating sensors.
4. “Tests”/Test Menu:
For testing actuators and testing the functions of the electric components
installed on the tractor. (e.g. buttons, potentiometers, solenoid valves etc.)
[ E ] E X I T
5. “Alarms”/Alarm list:
Displays all active and passive alarms. Alarms may also be cancelled from Fig. 83
this menu.
or

20-13
 Calibrations and electronic
diagnosis
4 choices: M A I N M E N U
1. “Monitors”/Monitor Menu: - - - - - - - - - - - - - - - -
Analyses all sensors in monitor mode. View data received from the different
electronic control units (e.g. sensor, button and potentiometer states etc.)
managing the tractor systems. 1 - M O N I T O R S
2. “Calibrations”/Calibration Menu: 2 - C A L I B R A T I O N S
For calibrating the different subsystems of the machine, performing the op- 3 - T E S T S
erations necessary for commissioning the tractor, calibrating the hydraulic 4 - A L A R M S
reverse shuttle and calibrating sensors.
3. “Tests”/Test Menu:
For testing actuators and testing the functions of the electric components
installed on the tractor. (e.g. buttons, potentiometers, solenoid valves etc.)
4. “Alarms”/Alarm list:
Displays all active and passive alarms. Alarms may also be cancelled from
[ E ] E X I T
this menu.
Fig. 84

---
Hidden menus are also available for certain ECUs, which can only be accessed by M E N U M E N U
entering a specific password. - - - - - - - - - - - - - - - -

1 - M O N I T O R S
2 - P A R A M E T R E S
3 - C A L I B R A T I O N S
4 - T E S T S
5 - A L A R M S

C - I N I T I A L I T .

[ E ] E X I T
Fig. 85

20.2.2 - HLHP ECU diagnostics - Clutch pedal calibration

1. To perform these operations, connect the ART/PC to the connector on the
A V A I L A B L E T E S T
left-hand side of the instrument panel, select the shuttle ECU (SMART
M E N U
LEVER) from the “AVAILABLE TESTS” menu and proceed as described
below.
DANGER 1 - S M A R T L E V E R
2 - C L U S T E R
The clutch pedal calibration operation must be carried out
with the engine off, the main gear and range gear levers in
neutral and the parking brake applied.
IMPORTANT
This procedure must be carried out each time the shuttle
ECU is renewed. C H O I C E
[ E ] E x i t

Fig. 86

20-14
Calibrations and electronic
diagnosis
2. From the presentation screen, press “E” to access the “Main Menu”.
= = = = = = = = = = = = = = = =
= S M A R T L E V E R =
= = = = = = = = = = = = = = = =
S N : 5 7 7 9

S W V e r s i o n
T C L E V - A A

D a t e :
2 2 - 1 0 - 2 0 0 9

C o n f i g u r a t i o n
T 5 0 0 0 G S 1 0 0 C V

[ E ] E x i t

Fig. 87
3. Press “3” to access the “Calibrations” / Calibrations menu.
M A I N M E N U
- - - - - - - - - - - - - - - -
1 - M o n i t o r s
2 - P a r a m e t e r s
3 - C a l i b r a t i o n s
4 - A l a r m s
5 - T e s t

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 88
4. From the “Calibrations” /Calibrations menu, press “1 - Pedal” / Pedal to ac-
C A L I B R A T I O N S
cess the clutch pedal calibration menu.
- - - - - - - - - - - - - - - -

1 - P e d a l
2 - R e v e r s e r

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 89

20-15
 Calibrations and electronic
diagnosis
5. The ART/PC Tester will then display the clutch pedal calibration page.
C L U T C H P E D A L
Fully depress the clutch pedal and press “B”.
- - - - - - - - - - - - - - - -
- P r e s s t h e p e d a l
a l l t h e w a y
- P r e s s [ B ]
- R e l e a s e i t
- P r e s s [ A ]

S w i t c h C l u t c h OF F

Mi n . P o s . 1 . 7 4 7
C u r r e n t 1 . 7 3 7
Ma x . P o s . 3 . 2 5 3
- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 90
6. If the clutch pedal travel limit switch is not operated when “B” is pressed, the
C L U T C H P E D A L
ECU will display an error message.
- - - - - - - - - - - - - - - -
Press “B” to save the value and continue with calibration. - P r e s s t h e p e d a l
a l l t h e w a y
- P r e s s [ B ]
- R e l e a s e i t
- P r e s s [ A ]
S w i t c h C l u t c h O F F
E r r o r : S w i t c h O F F
[ B ] I g n o r e e r r o r
M i n . P o s . 1 . 7 4 7
C u r r e n t 1 . 7 3 7
M a x . P o s . 3 . 2 5 3
- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 91
7. Fully release the clutch pedal and then press “A”.
C L U T C H P E D A L
- - - - - - - - - - - - - - - -
- P r e s s t h e p e d a l
a l l t h e w a y
- P r e s s [ B ]
- R e l e a s e i t
- P r e s s [ A ]

S w i t c h C l u t c h OF F

Mi n . P o s . 1 . 7 4 7
C u r r e n t 1 . 7 3 7
Ma x . P o s . 3 . 2 5 3
- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 91

20-16
Calibrations and electronic
diagnosis
8. If the clutch pedal travel limit switch is operated when key “A” is pressed,
C L U T C H P E D A L
the control unit will display an error message.
- - - - - - - - - - - - - - - -
Press “A” to save the value and continue with the calibration. - P r e s s t h e p e d a l
Press “E” to exit and access the following screen. a l l t h e w a y
- P r e s s [ B ]
- R e l e a s e i t
- P r e s s [ A ]
S w i t c h C l u t c h O N
E r r o r : S w i t c h O N
[ A ] I g n o r e e r r o r
M i n . P o s . 1 . 7 4 7
C u r r e n t 1 . 7 3 7
M a x . P o s . 3 . 2 5 3
- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 92

20.2.3 - HLHP ECU diagnostics - “Monitor screens” for ART/PC Tester

By using the “Monitor” screen you can monitor and check the functionality of the solenoid valves, sensors, potentiometers, switches
and other electrical components of the tractor.
WARNING
The use of the test functions can cause the direct activation of the gearbox solenoid valves, without supervision by the
control logic. It is therefore essential to ensure that the vehicle is in a safe condition before proceeding.

Introductory screen
The moment the tester is connected, the machine introductory screen will appear.

Fig. 93

20-17
 Calibrations and electronic
diagnosis
Select [1] to access the “Monitor” submenu, which contains the parameters used
for tractor management.

Fig. 94

Monitor
This menu contains the parameters used for tractor management.
l 1 – I/O
l 2 - “Transmission”
l 3 – CAN
l 4 - “Statistics”

Fig. 95

Monitor -> I/O Monitor

This menu contains the parameters acquired by the ECU and the output states.

20-18
Calibrations and electronic
diagnosis
l 1 - “Analog inputs”
l 2 - “Digital inputs”
l 3 - “Frequency inputs”
l 4 - “Pwr supplies”
l 5 – Outputs

Fig. 96

This menu contains the values read by the analogue sensors used by the ECU.
Analog inputs
l “CltchPed” = clutch pedal potentiometer
l “TempOil” = Engine oil temperature
l “Seat” = Seat sensor
l “SmartWheel” = Smart Wheel selector (optional)
l
Note
Values indicated in Volts [V]

Fig. 97

20-19
 Calibrations and electronic
diagnosis
This menu contains the values read by the digital sensors used by the ECU.
Digital Inputs - Digital Inputs
l “ConfClutch” = Comfort Clutch button
l “SwitchClutch” = Clutch pedal travel limit switch
l “Neutr Lever” = Neutral lever position switch
l “Frwrd Lever” = Forward lever position switch
l “Reverse Lever” = Reverse lever position switch
l “Seat” = Seat sensor switch
l “Pres4Bar pEv” = Pressure switch after pSV
l “Press11bar Ser” = Services pressure switch
l
Note
Values are given as [On-Off]

Fig. 98

This menu contains the values read by the speed sensors used by the ECU.
Frequencies input - Frequencies input
l “Reverser” = Reverse shuttle output speed frequency (+/- symbol indicates
direction of rotation)
l “Wheels” = Wheel speed sensor frequency
l
Note
Values indicated in Hertz [Hz]

Fig. 99

20-20
Calibrations and electronic
diagnosis
This menu contains the ECU input and output power feed values.
Pwr supplies - Power feeds
l “12V” = 12 Volt ignition switched power.
l “5V” = 5 Volt ECU output power.

Fig. 100

This menu contains the states of the ECU outputs.

Outputs - Outputs
l “EvP” = Proportional solenoid valve
m “Control” = Drive signal [mA]
m “Current” = Current [mA]

l “Ev Bwd” = Reverse solenoid valve

m “Control” = Control [ON/OFF]
m “Current” = Current [mA]

l “Ev Fwd” = Forward solenoid valve

m “Control” = Control [ON/OFF]
m “Current” = Current [mA]

Fig. 101

20-21
 Calibrations and electronic
diagnosis
Monitor -> Transmission
l “Des Dir” = Desired direction | “Real” = effective: [F-N-R]
l “Pedal Pos” = Clutch pedal position [%]
l “Evf” = Forward drive solenoid valve state [On-Off]
l “Evb” = Reverse drive solenoid valve state [On-Off]
l “EvP Curr” = Proportional solenoid valve current [mA]
l “PrsPev” = Proportional solenoid valve pressure state [mA]
l “Engine” = Engine speed [Rpm]
l “Invers” = Shuttle speed [Rpm]
l “Wheels” = Vehicle speed [Rpm]
l “Ratio” = Ratio engaged [No.]
l “OilTemp” = Transmission oil temperature [°C]
l “SmartWheel” = SmartWheel state

Fig. 102

Monitor -> CAN

This menu contains information relative to the state of the CanBus network.
l “Instrum. CAN” = “CAN” communication status with instrument panel
l “Engine CAN” = “CAN” communication status with engine ECU
l
Note
Values are given as [On-Off]

Fig. 103

Monitor -> Statistics

This menu contains information relative to machine usage statistics.

20-22
Calibrations and electronic
diagnosis
l “Invers.” = Number of direction changes performed.
l “Start.” = Number of automatic starts performed.
l “GearShift.” = Number of gear shifts performed (clutch button).

Fig. 104

20.2.4 - HLHP ECU diagnostics - “Parameter screens” for ART/PC Tester

The “Parameter” screens allow the user to enable/disable optional features and modify tractor calibration parameters.
Introductory screen
The moment the tester is connected, the machine introductory screen will appear.

Fig. 105

20-23
 Calibrations and electronic
diagnosis
Select [2] to access the “Parameters” submenu, which lists optional features and
contains the clutch parameters.

Fig. 106

Parameters
This menu contains optional features and clutch parameters.
l 1 - “Options” = Optional features
l 2 - “Clutches” = Clutch

Fig. 107

Parameters -> Options

This menu allows the user to enable/disable the optional features of the tractor.

20-24
Calibrations and electronic
diagnosis
l 1 - “Hi-Lo” = Hi-Lo function
l 2 - “SmartWheel” = SmartWheel function
l 3 - “Stop&Go” = Stop&Go function
l 4 - “Lim. 30 km/h” = 30 km/h speed limiter function

Fig. 108

Select the number corresponding to the desired optional feature, then select [0] to
disable the feature or [1] to enable.

Fig. 109

20-25
 Calibrations and electronic
diagnosis
Parameters -> Clutches
l “I Cont. F” = Forward drive clutch kiss point current: [mA]
l “I Cont. R” = Reverse drive clutch kiss point current: [mA]
l “TFill Fw” = Forward drive clutch fill time: [mSec]
l “TFill Rw” = Reverse drive clutch fill time: [mSec]

Fig. 110

20.2.5 - HLHP ECU diagnostics - “Alarms screens” for ART/PC Tester

The “Alarms” screens may be used to check the active and passive alarms memorised by the TCU, and cancel passive alarms.
Introductory screen
The moment the tester is connected, the machine introductory screen will appear.

Fig. 111

20-26
Calibrations and electronic
diagnosis
Select [4] to access the “Alarms” submenu, which contains all possible alarms

Fig. 112

Alarms
This menu contains all the active and passive alarms identified.
l 1 - “Active TCU” = Active alarms identified by TCU
l 2 - “Passive TCU” = Passive alarms identified by TCU
l 3 - “Deletion” = Cancel alarms

Fig. 113

Alarms ->Active TCU

This menu allows the user to check all active alarms identified by the TCU.

20-27
 Calibrations and electronic
diagnosis
l “#” = Alarm code displayed on instrument (T#)
l “SPN” = Number identifying faulty device
l “FMI” = Device fault mode
l “cnt” = Fault conditions

Press [D] to view information on the engine operating hour count (or use the instru-
ment for Euro2 engines) when alarm was generated.
Press [D] again to return to the alarm display screen.

Fig. 114

Alarms ->Passive TCU

This menu allows the user to check all passive alarms identified by the TCU.
l “#” = Alarm code displayed on instrument (T#)
l “SPN” = Number identifying faulty device
l “FMI” = Device fault mode
l “cnt” = Fault conditions

Press [D] to view information on the engine operating hour count (or use the instru-
ment for Euro2 engines) when alarm was generated.
Press [D] again to return to the alarm display screen.

Fig. 114

Alarms -> Clear

This menu allows the user to cancel all passive alarms identified by the TCU.

20-28
Calibrations and electronic
diagnosis
l 1 - “TCU” = Cancel alarms identified by TCU.

Fig. 115

The following screen is displayed.

Fig. 116

20.2.6 - Test screens for ART/PC Tester

The “Test” screens may be used to test the functions of the actuators (solenoid valves) connected to the TCU.

20-29
 Calibrations and electronic
diagnosis
Introductory screen
The moment the tester is connected, the machine introductory screen will appear.

Fig. 117

Select [5] to access the “Test” submenu, which contains all possible alarms

Fig. 118

Test
The user may select the solenoid valves to be tested in this menu.

20-30
Calibrations and electronic
diagnosis
l 1 - “Solen.Valves” = Solenoid valves connected to TCU

Fig. 119

Test ->Solenoid valves

All the solenoid valves connected to the TCU may be tested from this menu.
l 1 - “0A” = Deactivate proportional solenoid valve
l 2 - “0.5A” = Activate proportional solenoid valve at 50% (~ 500mA)
l 3 - “1A” = Activate proportional solenoid valve at 100% (~ 1,000mA)
l 4 - “OFF” = Deactivate reverse solenoid valve
l 5 - “ON” = Deactivate reverse solenoid valve
l 6 - “OFF” = Deactivate forward drive solenoid valve
l 7 - “ON” = Activate forward drive solenoid valve

Fig. 120

20-31
 Calibrations and electronic
diagnosis
20.3 - Commissioning and calibrating the tractor
20.3.1 - Check panel calibration
Purpose
The following assembly standard (p/n 930774/09) is designed to provide instructions for correct calibration of the new digital Check
Panel.
Setting parameters with the ART® Diagnostic Tester
Using the ART diagnostic tester, the instrument panel can be set up so that it func-
A V A I L A B L E T E S T
tions correctly on any tractor model.
M E N U
l Tractor configuration
l Wheels constant

Connect the tester to the diagnostics socket and turn the starter key to “power”. 1 - S M A R T L E V E R
The main tester page will display the names of the electronic control units con- 2 - C L U S T E R

nected to the serial line:

l Select “2 - Cluster”

C H O I C E

[ E ] E x i t

Fig. 121

The following screen appears, showing the SW version and the date:
C L U S T E R
Press E
- - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - -

F i r m w a r e I C 2 9 6 A D
0 2 / 0 2 / 2 0 1 2

[ E ] E x i t

Fig. 122

The “Main Menu” screen will appear.

M A I N M E N U
- - - - - - - - - - - - - - - -

1 - M o n i t o r s
2 - C a l i b r a t i o n s
3 - T e s t
4 - A l a r m L i s t

[ E ] E x i t

Fig. 123

20-32
Calibrations and electronic
diagnosis
Press “2 - Calibrations” to enter the calibration menu.
C A L I B R A T I O N M E N U
The following screen will appear.
- - - - - - - - - - - - - - - -
Press “1 - Parameters” / Parameters to enter the parameter calibration menu.
1 - P a r a m e t e r s

[ E ] E x i t

Fig. 124

Change machine configuration

l “Wheel” C A L I B R A T I O N
Wheels constant setting
- - - - - - - - - - - - - - - -
l “AlarmBelt”
Belt alarm setting
1 - W h e e l 3 3 0 9
l “ActiveConf”
2 - A l a r m B e l t 0
Instrument configuration setting
l “Vel” 3 - A c t i v e C o nf 2 1
4 - V e l [ 1 = m p h ] 0
Speed units of measurement setting:
m 0 = km/h
5 - C l o c k [ 1 = 1 2 h ] 0
m 1 = mph 6 - M a x T e m p 1 0 8

l “Clock”
Time display format setting:
m 0 = 24h
m 1 = 12h
[ E ] E x i t
l “MaxTemp” (°C)
Max. engine coolant temperature value above which the red warning light Fig. 125
on the instrument panel will illuminate.
Press “3 - ActiveConf” / Configuration to configure the instrument on the basis of the machine on which it is installed:
Table 21
Machine Version Hydraulic Re- Lift Instrument con-
verse Shuttle figuration
Explorer³ 85, 100, 110 E3 LS MY2011 EU-USA No No 27
Explorer³ 85, 100, 110 E3 LS MY2011 EU-USA (Hi-Lo) No No 41
Explorer³ 85, 100 E3 GS MY2011 EU-USA Yes No 29
Explorer³ 85, 100 E3 GS MY2011 EU-USA (Hi-Lo) Yes No 28
Explorer³ 110 E3 GS MY2011 EU-USA Yes No 30
Explorer³ 85, 100, 110 E3 LS MY2011 + EU-USA No HLHP 31
Electronic lift
Explorer³ 85, 100, 110 E3 LS MY2011 + EU-USA (Hi-Lo) No HLHP 42
Electronic lift
Explorer³ 85, 100 E3 GS MY2011 + Elec- EU-USA Yes HLHP 32
tronic lift
Explorer³ 85, 100 E3 GS MY2011 + Elec- EU-USA (Hi-Lo) Yes HLHP 33
tronic lift
Explorer³ 110 E3 GS MY2011 + Electronic EU-USA Yes HLHP 34
lift

20-33
 Calibrations and electronic
diagnosis
On the next screen, enter the configuration number for the machine on which the
3 - A c t i v e C o n f
instrument panel is installed:
- - - - - - - - - - - - - - - -
Press “E” to exit, then press “C” to confirm and save the configuration.

A c t u a l : 2 9

N e w :

[ D ] E r a s e
[ E ] E x i t

Fig. 126

Edit or Input wheels constant

Return to the “Calibration” menu.
C A L I B R A T I O N
Press “1 - Wheels” / Wheels
- - - - - - - - - - - - - - - -

1 - W h e e l 3 3 0 9
2 - A l a r m B e l t 0
3 - A c t i v e C o nf 2 1
4 - V e l [ 1 = m p h ] 0
5 - C l o c k [ 1 = 1 2 h ] 0
6 - M a x T e m p 1 0 8

[ E ] E x i t

Fig. 126

Enter the constant on the basis of the table shown.

1 - W h e e l
Press “E” to exit, then press “C” to confirm and save the configuration.
- - - - - - - - - - - - - - - -

A c t u a l : 3 3 0 9

N e w :

[ D ] E r a s e
[ E ] E x i t

Fig. 127

Wheels constants
The wheels constant parameter to be entered in the instrument must represent the pulses for 25m generated by the speed measu-
rement sensor.
Table 22
tyre constant
410C 420 - 430 hp
13.6 R38 5098 4671

20-34
Calibrations and electronic
diagnosis
tyre constant
410C 420 - 430 hp
14.9 R38 4518
16.9 R30 5429 4973
16.9 R34 5064 4640
16.9 R38 4348
18.4 R30 5240 4801
18.4 R34 4489
340/85 R38 5098 4671
380/85 R38 4489
420/85 R30 5429 4973
420/85 R34 5064 4640
420/85 R38 4348
460/85 R30 5240 4801
460/85 R34 4489
480/70 R30 5429 4973
480/70 R34 5064 4640
480/70 R38 4348
520/70 R34 4489
540/65 R30 5429 4973
540/65 R34 5064 4640
540/65 R38 4348

Changing the km/h - mph Parameter

Return to the “Calibration” menu.
C A L I B R A T I O N
Press “4 - Vel” to enter the km/h or mph/h selection menu
- - - - - - - - - - - - - - - -
To display the speed in mph press (1) or press (0) to display the speed in km/h.
Press “E” to exit, then press “C” to confirm and save the configuration. 1 - W h e e l 3 3 0 9
2 - A l a r m B e l t 0
3 - A c t i v e C o nf 2 1
4 - V e l [ 1 = m p h ] 0
5 - C l o c k [ 1 = 1 2 h ] 0
6 - M a x T e m p 1 0 8

[ E ] E x i t

Fig. 127

Setting parameters with the control buttons

The two buttons on the instrument panel are used set certain operating parameters and to select the various display functions.
Table 23
Description Abbreviation
Hour meter display button (high position) PD_H
Multifunction display button (low position) PD_L
Parameter Setting
Press buttons PD_H and PD_L simultaneously and hold them for more than 2 seconds to enter parameter setting mode. The first
parameter that can be set by pressing the buttons is the clock.
Press button PD_L briefly to increase the hours setting one unit at a time (if the hours digit is flashing) or the minutes setting (if the
minutes digit is flashing). The setting procedure always starts with the hours by default.
Press the PD_H button briefly to change the digit being edited, from hours to minutes or from minutes to hours.
A prolonged press of the PD_H button serves to save the new time and change the parameter being edited, from the time to the wheel
constant. If, however, no buttons are pressed for 10 seconds, the system will quit parameter setting mode without saving any of the
changes made to the clock. When the new time has been saved or when the system times out and therefore quits programming, the
display stops flashing.
Likewise, brief presses of PD_L increase the digit being edited, while brief presses of PD_H serve to change the parameter subject

20-35
 Calibrations and electronic
diagnosis
to editing (relative to the size of the tyres).
Press and hold button PD_H to save the new tyre size and change to the next editable parameter: in this case, indicator lamp
brightness. If, however, no buttons are pressed for 10 seconds the system will quit parameter setting mode without saving any of the
changes made to the tyre size (although the changes made to the time setting will be saved).
Likewise, short presses of PD_L increase the digit being edited, which flashes at 1Hz (relative to the indicator lamp brightness).
Check that the message LUM appears on the LCD3 followed by a flashing letter, which can be H, M, or L corresponding to the three
brightness levels: High, Medium, and Low.
A prolonged press of PD_H serves to save the indicator lights brightness parameter and quit parameter setting mode. If, however,
no buttons are pressed for 10 seconds the system will quit parameter setting mode without saving the change made to the indicator
lights brightness setting (although changes made to the time and tyre size settings will be saved).
PD_H button
A brief press of the PD_H button makes it possible to change the information shown on the second line of the central display. When
the on-board panel is switched on, the total hour meter is displayed.
A short press of PD_H shows the metres counter (if available), while a second short press causes the display to return to the total
hours meter, and so forth. During display of the metres counter, a prolonged press of PD_H serves to reset the total. The total hour
meter cannot be reset. At each press (short or prolonged) of the button the buzzer emits a tone.
PD_L button
A prolonged press of PD_L resets the partial hour meter. At each press (short or prolonged) of the button the buzzer emits a tone
(different from the tone associated with PD_H).
20.3.2 - Introduction to commissioning the tractor
All the information required to restore correct operation of all electronic systems on the tractor is provided by the commissioning
procedure. Whenever an electronic control unit of the tractor is changed or a calibration-sensitive electronic component replaced, the
tractor must be recomissioned. The necessary procedures must be carried out by a skilled technician, who must follow the instruc-
tions in the manual precisely.
20.3.3 - Replacing reverse shuttle ECU - Basic commissioning procedure
1. The steps of the commissioning activation procedure are as follows:
A V A I L A B L E T E S T
m Shut off the engine, put the main gearbox and range gearbox in M E N U
neutral.
m Connect the A.R.T. instrument to the diagnostic socket.
m Turn the ignition switch to “ON”.
1 - S M A R T L E V E R
m Select SMART LEVER from the list of connected ECUs.
2 - C L U S T E R

C H O I C E
[ E ] E x i t

Fig. 128

20-36
Calibrations and electronic
diagnosis
2. From the welcome screen, press 0 twice
= = = = = = = = = = = = = = = =
= S M A R T L E V E R =
= = = = = = = = = = = = = = = =
S N : 5 7 7 9

S W V e r s i o n
T C L E V - A A

D a t e :
2 2 - 1 0 - 2 0 0 9

C o n f i g u r a t i o n
T 5 0 0 0 G S 1 0 0 C V

[ E ] E x i t

Fig. 129
3. A password prompt will appear. Enter the password.

P a s s w o r d : * * * * * *

Fig. 130
4. On entering the password, the introductory screen will re-appear. Press [E]
M A I N M E N U
to enter the main menu. If the password is entered correctly, the option “C-
- - - - - - - - - - - - - - - -
Initialize” (normally hidden) will be displayed
1 - M o n i t o r s
2 - P a r a m e t e r s
3 - C a l i b r a t i o n s
4 - A l a r m s
5 - T e s t

C - I n i t i a l i z a t i o n

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 131

20-37
 Calibrations and electronic
diagnosis
5. Press [C] to activate the machine commissioning procedure. The following
I N I T I A L I Z A T I O N
menu is displayed on the SAME ART instrument:
- - - - - - - - - - - - - - - -
M A C H I N E
S T A R T U P

- - - - - - - - - - - - - - - -
1 - R e p r o g . E e p r o m
2 - M a c h . S t a r t - U p
- - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 132
6. If necessary, re-initialise the eeprom as instructed in the following paragraph
See para. 20.3.4 - Replacing the reverse ... - page 20-38
otherwise go to paragraph
See para. 20.3.5 - Replacing the reverse ... - page 20-39

20.3.4 - Replacing the reverse shuttle ECU - EEPROM re-initialisation

1. Perform the steps described in chapter
See para. 20.3.3 - Replacing reverse shut... - page 20-36
On selecting option [1] a warning message appears.
If you continue with the procedure, the Eeprom will be re-initialised and the parameter values in memory will be overwritten
with the default values.
2. Press [E] to cancel or [C] to continue with the re-initialisation procedure.
R E I N I T . E E P R O M
- - - - - - - - - - - - - - - -

= = = = = = = = = = = = = = = =
! A T T E N T I O N !
T H E M E M O R Y W I L L
B E C O M P L E T E L Y
R E P R O G R A M M E D
= = = = = = = = = = = = = = = =
P R E S S [ C ]
T O C O N T I N U E

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 133
3. Wait. On termination of the re-initialisation procedure the following mes-
R E I N I T . E E P R O M
sage is displayed.
- - - - - - - - - - - - - - - -

M E M O R Y
R E I N I T I A L I S E D
C O R R E C T L Y

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 134

20-38
Calibrations and electronic
diagnosis
4. Eeprom re-initialisation in now complete. Press [E] to return to the main commissioning menu.

20.3.5 - Replacing the reverse shuttle ECU - End-of-line tractor programming

1. The end-of-line programming procedure consists of following steps:
m Configuration of the model
m Shuttle pedal calibration
m Option selection

2. To perform the commissioning procedure, repeat the steps described in

I N I T I A L I Z A T I O N
chapter
See para. 20.3.3 - Replacing reverse shut... - page 20-36 - - - - - - - - - - - - - - - -
M A C H I N E
S T A R T U P

- - - - - - - - - - - - - - - -
1 - R e p r o g . E e p r o m
2 - M a c h . S t a r t - U p
- - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 135
3. Press [2] to activate the commissioning procedure. A warning message will be displayed.
DANGER
Once the procedure has been started, the transmission will remain in neutral and it will not be possible to use
the tractor until all the steps in the commissioning procedure have been completed. In particular, if the machine
is switched off before the procedure has terminated, when the tractor is next switched on an alarm message will
appear indicating that the re-initialisation has not been completed and therefore it will be necessary to repeat
the commissioning procedure.
4. Press [C] to activate the line end programming procedure.
! ! A T T E N T I O N ! !
- - - - - - - - - - - - - - - -

T H E M A C H I N E
C A N N O T B E U S E D
U N T I L T H E E N D
O F T H E P R O C E D U R E

- - - - - - - - - - - - - - - -

P R E S S [ C ] T O
C O N T I N U E

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 136

20-39
 Calibrations and electronic
diagnosis
5. As soon as line end programming is activated, the family configuration
C O N F I G U R E F A M I L
page appears on the ART.
- - - - - - - - - - - - - - - -
Select the option “1 - EXPLORER3”, then press “E” to exit and “C” to con-
1 - T y p e F a m i l y 1
firm and access the next screen.

1 : E X P L O R E R 3
2 : F R U T T _ D O R A D O

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 137
6. Once family configuration has been completed, the ART will display the
E N G I N E M O D E L
engine selection page.
- - - - - - - - - - - - - - - -
If commissioning is carried out on a complete machine (rather than just a 1 - E n g i n e T i p e 2
cab) the control unit can identify the type of engine installed. The identified
engine type will therefore be proposed and the operator can simply confirm 1 - D E U T Z - S A M E
the type by pressing [E]. 2 - D E U T Z E U R O 3

[ E ] E x i t
[ C ] S t o r e

Fig. 138
7. If the configuration proposed by the system is not correct, or if no configuration is proposed, the operator may modify the
configuration by pressing [1] and choosing the engine type from among those listed.
Select option 3
Table 24

Engine Identification (string on ART)

Deutz 2012 Tier 2 with mechanical governor DEUTZ - SAME
SAME 1000.4 WTI Tier 3A DEUTZ - SAME
Deutz 2012 Tier 3A with electronic governor DEUTZ - EURO3
8. On pressing [E] to conform the selection, the transmission configuration
C O N F I G U -R E T C U
screen will appear.
- - - - - - - - - - - - - - - -
Enter the value corresponding to the type of transmission installed on the
1 : T r a n s . - T y p e 0
tractor, then press “C” and “E” to exit and move on to the next screen.
Note 1 : T 4 0 0 0 8 5 / 9 0
For the Deutz version, select the transmission referring to 2 : T 5 0 0 0 1 0 0
3 : T 5 1 0 0 1 0 5 / 1 1 0
the table

Table 25

TRANSMISSION DEUTZ MODEL [ E ] E x i t

T4000 410
T5000 420 [ C ] S t o r e
T5100 430 Fig. 139

20-40
Calibrations and electronic
diagnosis
9. The ART/PC Tester then displays the accelerator pedal calibration page.
P E D A L C A L I B R .
Release the accelerator pedal, wait for the value to stabilise, then press “C”
- - - - - - - - - - - - - - - -
to confirm the parameter and proceed to the next calibration step.

R e l e a s e
a c c e l e r a t o r
p e d a l t o m i n a n d
t h e n p r e s s [ C ]

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 140
10. Fully depress the accelerator pedal and, when the value has stabilised,
P E D A L C A L I B R .
press button “C” to confirm the parameter and terminate the calibration
- - - - - - - - - - - - - - - -
procedure.

P r e s s
a c c e l e r a t o r
p e d a l t o m a x a n d
t h e n p r e s s [ C ]

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 141
11. If the calibration was not completed successfully, the following message
P E D A L C A L I B R .
will be displayed:
- - - - - - - - - - - - - - - -
“Error into calibration procedure”.
DANGER
C A L I B R A T I O N
In this case, check that the accelerator pedal sensor is not O K
faulty or installed incorrectly, then repeat the procedure.

If the calibration was successful, the following message will be displayed: E R R O R

I N T O C A L I B R A T I O N
“Calibration ok”
P R O C E D U R E
Press “E” to exit and access the following screen.

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 142

20-41
 Calibrations and electronic
diagnosis
12. The ART/PC Tester will then display the hand throttle calibration page.
H A N D G A S C A L I B R .
Move the throttle lever towards the front of the tractor (MAX position) and
- - - - - - - - - - - - - - - -
press “C” to confirm the parameter.

P u s h h a n d g a s
t o m a x a n d
t h e n
p r e s s [ C ]

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 143
13. Move the throttle lever back towards the rear of the tractor (MIN position)
H A N D G A S C A L I B R .
and press “C” to confirm the parameter and terminate the calibration pro-
- - - - - - - - - - - - - - - -
cedure.

P u l l h a n d g a s
t o m i n a n d
t h e n
p r e s s [ C ]

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 144
14. If the calibration was successful, the following message will be displayed:
H A N D G A S C A L I B R .
“Calibration ok”
- - - - - - - - - - - - - - - -
Press “E” to exit and access the following screen.

C A L I B R A T I O N
O K

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 145

20-42
Calibrations and electronic
diagnosis
15. The ART/PC Tester will then display the clutch pedal calibration page.
C L U T C H P E D A L
Fully depress the clutch pedal and press “B”.
- - - - - - - - - - - - - - - -
The “Max.Pos.” value is set to the “Actual” value. - P r e s s t h e p e d a l
a l l t h e w a y
- P r e s s [ B ]
- R e l e a s e i t
- P r e s s [ A ]

S w i t c h C l u t c h O N

M i n . P o s . 1 . 7 4 7
C u r r e n t 1 . 7 3 7
M a x . P o s . 3 . 2 5 3
- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 146
16. The ECU displays an error message if the clutch pedal travel limit switch is
C L U T C H P E D A L
not activated when button [B] is pressed.
- - - - - - - - - - - - - - - -
Check that the pedal is fitted correctly. - P r e s s t h e p e d a l
Note a l l t h e w a y
- P r e s s [ B ]
Even if this error message appears, it will still be possible to - R e l e a s e i t
- P r e s s [ A ]
calibrate the clutch pedal. The machine may be driven, but
the alarm will remain active. S w i t c h C l u t c h O F F
E r r o r : S w i t c h O F F
Press button [B] again to accept the calibration even though the switch was [ B ] I g n o r e e r r o r
not pressed. M i n . P o s . 1 . 7 4 7
C u r r e n t 1 . 7 3 7
M a x . P o s . 3 . 2 5 3
- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 147
17. Fully release the clutch pedal and then press “A”.
C L U T C H P E D A L
- - - - - - - - - - - - - - - -
- P r e s s t h e p e d a l
a l l t h e w a y
- P r e s s [ B ]
- R e l e a s e i t
- P r e s s [ A ]

S w i t c h C l u t c h O N

M i n . P o s . 1 . 7 4 7
C u r r e n t 1 . 7 3 7
M a x . P o s . 3 . 2 5 3
- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 147

20-43
 Calibrations and electronic
diagnosis
18. If the clutch pedal travel limit switch is operated when key “A” is pressed,
C L U T C H P E D A L
the control unit will display an error message.
- - - - - - - - - - - - - - - -
Check that the pedal is fitted correctly. - P r e s s t h e p e d a l
Note a l l t h e w a y
- P r e s s [ B ]
Even if this error message appears, it will still be possible to - R e l e a s e i t
- P r e s s [ A ]
calibrate the clutch pedal. The machine may be driven, but
the alarm will remain active. S w i t c h C l u t c h O F F
E r r o r : S w i t c h O F F
Press button [A] again to accept the calibration even though the switch was [ A ] I g n o r e e r r o r
not pressed. M i n . P o s . 1 . 7 4 7
C u r r e n t 1 . 7 3 7
M a x . P o s . 3 . 2 5 3
- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 148
19. The ART/PC Tester will then display the page for selection of the optional
O P T I O N S
equipment installed on the tractor.
- - - - - - - - - - - - - - - -
Press “1” to access the menu “1-Hi-Lo”.
1 - H m l / H i - L o 1
2 - S m a r t W h e e l 1
3 - S t o p & G o 0

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 149
20. Select “1-Hml / Hi-Lo” to call up the HML / Hi-Lo menu.
1 - H i - L o
Enter the value corresponding to the tractor configuration, then press “E” to
- - - - - - - - - - - - - - - -
confirm the parameter.
Important
If you enter the wrong value by mistake, press “D” to cancel A c t u a l : 1
the operation.
N e w : _

Table 26

VALUE CONFIGURATION
0 Hi-Lo absent
[ D ] C a n c e l
1 Hi-Lo present
[ E ] E x i t

Fig. 150

20-44
Calibrations and electronic
diagnosis
21. Press “C” to confirm the configuration or press “A” to cancel the operation
1 - H i - L o
and return to the “Options” menu in order to repeat the procedure.
- - - - - - - - - - - - - - - -

A c t u a l : 1

N e w : 0

[ A ] A b o r t
[ C ] C o n f i r m

Fig. 151
22. If the procedure was successful, a screen confirming the configuration will
! ! A T T E N T I O N ! !
be displayed.
- - - - - - - - - - - - - - - -
Press “E” to return to the main menu.
Turn the ignition switch to “O” (OFF) then back to “I” (ON) and perform the
procedure to calibrate the reverse shuttle clutches. M A C H I N E
S T A R T - U P
Note E N D E D
S U C C E S S F U L L Y
At the end of the procedure, alarm T10 is displayed prompt-
ing the technician to perform clutch calibration.
= = = = = = = = = = = = = = = =

R E S T A R T
T H E E N G I N E

[ E ] E x i t

Fig. 152

20-45
 Calibrations and electronic
diagnosis
20.3.6 - Renewal of the shuttle ECU - Introductory notes (AGROFARM 410 -> ZKD-
W470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)
Introductory notes on the clutch calibration procedure
The shuttle clutch must be calibrated by the technician in the following cases:
l After renewal of one or both shuttle clutches.
l After renewal of the clutch control proportional solenoid valve.
l After the clutch has bedded in (in the case of new or revised tractors) or after years of use, if the clutch or automatic direction
change (without the use of the clutch pedal) is too sudden or too slow.
l Whenever the shuttle ECU is renewed.
l When the line programming procedure is carried out
l On appearance of the transmission alarm T10 - Shuttle clutches not calibrated.
The technician has the choice of three calibration procedures.
C A L I B R . R E V E R S E R
l “Automatic” / Automatic calibration - - - - - - - - - - - - - - - -
in which the control unit independently sets the parameters for clutch en-
gagement characteristics. 1 - A u t o m a t i c
l “Manual” / Manual calibration 2 - M a n u a l
where the technician can alter the parameter settings and thus create a 3 - C o m f o r t p a r a m
personalised clutch engagement curve to obtain a smoother, more comfort-
able response from the tractor during travel direction changes.
l “Comfort param” / Comfort parameters
where the technician can adjust tractor behaviour, the comfort settings and
speed at which manoeuvres are performed to suit personal requirements.

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 153

Depending the status of the tractor, the technician can decide to perform just one of the three calibration procedures.
The table below provides guidelines for the procedures to carry out according to the type of fault encountered.
Table 27
Problem encountered Automatic cali- Manual calibra- Editing the com-
bration tion fort parameters
Alarm T10 X
Renewal of control unit X
Renewal of mechanical/hydraulic assembly X
Replacement of proportional valve X
Asymmetric behaviour (one good clutch, one poor clutch) X
Irregular behaviour (both clutches too sharp or too slow) X
Customisation of shuttle behaviour X

20.3.7 - Renewal of the shuttle ECU - Automatic calibration (AGROFARM 410 -> ZK-
DW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)
Automatic calibration of the shuttle clutches
1. IMPORTANT
This procedure should only be carried out if the technician finds during a test drive that shuttle clutch engage-
ment is either too sudden or too slow when moving off from stationary or during direction changes without using
the clutch pedal.
2. m Increase engine speed to 1,500 rpm
m Start the engine and bring the transmission oil to approximately 35°C.
m Place the tractor on level ground with no obstacles
m Leave a clear space of at least 5 m in front of and behind the machine.

20-46
Calibrations and electronic
diagnosis
3. From the “Main Menu” / Main Menu, select “3 - Calibrations” / Calibrations
M A I N M E N U
to access the calibration menu.
- - - - - - - - - - - - - - - -
1 - M o n i t o r s
2 - P a r a m e t e r s
3 - C a l i b r a t i o n s
4 - A l a r m s
5 - T e s t

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 154
4. From the “Calibrations” /Calibrations menu, select “2 - Reverser” / Shuttle
C A L I B R A T I O NS
to access the hydraulic reverse shuttle calibration menu.
- - - - - - - - - - - - - - - -

1 - P e d a l
2 - R e v e r s e r
3 - S t o p A n d G o

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 155
5. The press “1 - Automatic” / Automatic to access the automatic clutch cali-
C A L I B R . R E V E R S E R
bration procedure.
- - - - - - - - - - - - - - - -

1 - A u t o m a t i c
2 - M a n u a l
3 - C o m f o r t p a r a m

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 156

20-47
 Calibrations and electronic
diagnosis
6. Check that all the conditions indicated on the monitor are met, then press
A U T O M . C A L I B R A T .
[E].
- - - - - - - - - - - - - - - -
Press any key on ART. Select the travel direction to be calibrated (for ex-
C a l i b r a t i o n s
ample FORWARD). c o n d i t i o n s :
- - - - - - - - - - - - - - - -

1 ) O N L E V E L G R N D
2 ) 2 n d F a s t ( H i )
3 ) O i l T 3 5 - 4 5 C
4 ) 1 5 0 0 R P M E n g i n e

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 157
7. The tractor moves forward intermittently and the values shown on screen
A U T O M . C A L I B R A T .
change until the optimal values are found. When the calibration procedure
- - - - -
- - - - - - - -
- - -
is complete, the message “Calib. Complete” /Calibration complete is dis-
O i l T
e m p . + 3 8
played. If you wish to repeat the procedure, return the shuttle lever to neu- E n g i n
e R
M P 1 5 6 1
tral and then move it back to the travel direction selected previously. To - - - - F
O R W
R A D - - - - -
save the values obtained during calibration, press “E”. P e a k c u r
n r t 5 6 5
“Oil Temp.” / Transmission oil temperature S t . e n d c
n r t 5 4 3
C o r r e c t i
n o + 1
“Engine RPM” / Engine speed
C A L I B . C O
M P L E T E
“Peak currnt” / Peak current
- - - - R E V E R S E - - - - -
“St.end crnt” / Final current P e a k c u r r n t 0
“Correction” S t . e n d c r n t 0
C o r r e c t i o n + 1

[ E ] E x i t

Fig. 158
8. Press “C” to save the data or press A” to quit without saving.
C O N F I R M
Repeat the calibration procedure from point 5 to point 8 for the other travel
- - - - - - - - - - - - - - - -
direction, then test the results by carrying out manoeuvres using the shut-
tle. If the result is not satisfactory, proceed with the manual calibration of C - C o n f i r m
the shuttle clutches. A - A b o r t

- - - - - - - - - - - - - - - -

Fig. 159

20-48
Calibrations and electronic
diagnosis
20.3.8 - Renewal of the shuttle ECU - Manual calibration (AGROFARM 410 -> ZKD-
W470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)
Procedure for manual calibration of the shuttle clutches
1. Start the engine and bring the transmission oil to approximately 40°C.
2. Park the tractor on a flat tarmac surface with at least 5 metres free clearance in front and perform the following operations.
m Put the shuttle lever in neutral.
m Take the engine revs to 1,500 rpm.
m Select 2nd gear in the fast range (hare symbol).
m If the transmission is equipped with the Hi-Lo gearbox: select HI speed (‘hare’ symbol).

Notes on how to edit parameter settings during manual calibration

1. When the technician performs automatic clutch calibration, the control unit calculates the operating parameter values by ap-
plying an algorithm to define the ideal conditions. In some cases, these parameters, even if correct from a hydraulic or me-
chanical point of view, make the tractor response too sudden when the clutch is engaged. In this case, the technician should
first attempt to define the type of response by performing, in automatic mode (i.e. without using the clutch pedal), several
direction changes and standing starts in both directions and at various engine speeds (e.g. 1,000, 1,500, 2,000 and max rpm)
and in calibration conditions (for details, see calibration procedures).
The possible responses are:
m Different response when changing between forward and reverse travel (balancing):

when changing direction from forward to reverse the tractor behaves differently than when changing from reverse to
forward.
m Excessively harsh (or excessively soft) direction change (response): The tractor engages the direction requested by

the technician very rapidly, and instead of gradually beginning to move, the tractor starts with a jolt (similar to the effect
of releasing the clutch suddenly in a car).
m Excessively slow (or excessively rapid) direction change (acceleration): The tractor engages the direction requested by

the technician, but takes too long to execute the action, with no positive feel.
Procedure for manual calibration of the shuttle clutches
1. IMPORTANT
This procedure should only be carried out if the technician finds during a test drive that shuttle clutch engage-
ment is either too sudden or too slow when moving off from stationary or during direction changes without using
the clutch pedal.
2. Start the engine and bring the transmission oil to approximately 40°C.
3. Park the tractor on a flat tarmac surface with at least 50 metres free clearance in front and perform the following operations.
m Put the shuttle lever in neutral.
m Select 2nd gear in the fast range.
m If the transmission is equipped with the Hi-Lo gearbox: select HI speed (‘hare’ symbol).

4. From the “Main Menu”, select “3 - Calibrations” /Calibrations to access the

M A I N M E N U
calibration menu.
- - - - - - - - - - - - - - - -
1 - M o n i t o r s
2 - P a r a m e t e r s
3 - C a l i b r a t i o n s
4 - A l a r m s
5 - T e s t
6 - E n g i n e

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 160

20-49
 Calibrations and electronic
diagnosis
5. From the “Calibrations” / Calibrations menu, select “2 - Reverser” / Shuttle
C A L I B R A T I O N S
to access the hydraulic reverse shuttle calibration menu.
- - - - - - - - - - - - - - - -

1 - P e d a l
2 - R e v e r s e r

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 161
6. The press “2 - Manual” / Manual to access the manual clutch calibration
C A L I B R . R E V E R S E R
procedure.
- - - - - - - - - - - - - - - -

1 - A u t o m a t i c
2 - M a n u a l
3 - C o m f o r t p a r a m

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 162
7. “F/R balance” / Direction change response
M A N U A L C A L I B R A T .
To balance the response to direction change commands, select “1 - F/R - - - - - - - - - - - - - - - -
balance” / F/R balance to access the relative menu. 1 - F / R b a l a n c e
2 - R e v . R e s p o n s e
3 - R e v . A c c e l e r a t
4 - P e d a l B e h a v .

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 163

20-50
Calibrations and electronic
diagnosis
8. Press “C” or “D” to slow down or speed up the transition from reverse to
F / R B A L A N C E
forward travel.
- - - - - - - - - - - - - - - -
Press “A” or “7” to slow down or speed up the transition from forward to
reverse travel.
Press “E” to continue. I c o n t a c t F 5 4 3
I c o n t a c t R 5 5 9
Key:
“Fwd” / Forward
“Bwd” / Reverse
D : F w d + P r o m p t
“Prompt” / Response C : F w d - P r o m p t
7 : B w d + P r o m p t
Note
A : B w d - P r o m p t
The purpose of this stage of the calibration procedure is - - - - - - - - - - - - - - - -
simply to reduce the difference in behaviour between for- [ E ] E x i t
ward and reverse drive. When carrying out this step, we rec- Fig. 164
ommend performing direction changes with the pedal only
slightly released, and trying to maintain the same accelera-
tion and speed (approx. 1 km/h) in both directions.
9. Press “C” to confirm and save the setting, or press “A” to exit without sav-
C O N F I R M
ing.
- - - - - - - - - - - - - - - -

C - C o n f i r m
A - A b o r t

- - - - - - - - - - - - - - - -

Fig. 165
10. To adjust the response of the hydraulic shuttle, select “2 - Rev. Response”
M A N U A L C A L I B R A T .
/ Reverse response to access the relative menu.
- - - - - - - - - - - - - - - -
IMPORTANT 1 - F / R b a l a n c e
2 - R e v . R e s p o n s e
The “Response” parameter regulates the characteristics of 3 - R e v . A c c e l e r a t
the initial stage of direction change manoeuvres. This pa- 4 - P e d a l B e h a v .
rameter can be adjusted to eliminate any grabbing in shuttle
clutches operation or the sensation that the clutches have
failed to engage.

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 165

20-51
 Calibrations and electronic
diagnosis
11. Press “7” or “A” to increase or reduce shuttle response speed.
R E V E R . R E S P O N S E
Press “E” to continue.
- - - - - - - - - - - - - - - -
Key:
“More Prompt” / Faster response
“Less Prompt” / Slower response R e s p o n s e : 4 5 0

7 : M o r e P r o m p t
A : L e s s P r o m p t
- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 166
12. Press “C” to confirm and save the setting, or press “A” to exit without sav-
C O N F I R M
ing.
- - - - - - - - - - - - - - - -

C - C o n f i r m
A - A b o r t

- - - - - - - - - - - - - - - -

Fig. 166
13. To adjust the speed of the travel direction changes, select “3 - Rev. Accel-
M A N U A L C A L I B R A T .
erat” / Reverse Acceleration to access the relative menu.
- - - - - - - - - - - - - - - -
IMPORTANT 1 - F / R b a l a n c e
2 - R e v . R e s p o n s e
The “Acceleration” parameter regulates the speed at which 3 - R e v . A c c e l e r a t
the direction change manoeuvre is brought to a conclusion. 4 - P e d a l B e h a v .
This parameter should be changed when the time taken to
complete a direction change manoeuvre is either too long
or too short.

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 166

20-52
Calibrations and electronic
diagnosis
14. Press “7” or “A” to increase or reduce the speed of the shuttle.
R E V E R . A C C E L E R A T .
Press “E” to continue.
- - - - - - - - - - - - - - - -
Key:
“Quicker”
“Slower” A c c e l e r a t . : 6 0 0

7 : Q u i c k e r
A : S l o w e r
- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 167
15. Press “C” to confirm and save the setting, or press “A” to exit without sav-
C O N F I R M
ing.
- - - - - - - - - - - - - - - -

C - C o n f i r m
A - A b o r t

- - - - - - - - - - - - - - - -

Fig. 167
16. To change the clutch pedal position at which torque transmission begins,
M A N U A L C A L I B R A T .
select “4 - Pedal Behav.” from the relative menu
- - - - - - - - - - - - - - - -
IMPORTANT 1 - F / R b a l a n c e
2 - R e v . R e s p o n s e
The parameter “Pedal Behav.” is used to alter the position 3 - R e v . A c c e l e r a t
at which the shuttle clutches start delivering torque to the 4 - P e d a l B e h a v .
transmission during clutch pedal release.

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 167

20-53
 Calibrations and electronic
diagnosis
17. Press “7” or “A” to raise or lower the release point.
P E D A L C L U T C H
Press “E” to continue.
- - - - - - - - - - - - - - - -
Key:
“Higher”
“Lower” I n c h i n g P o s : + 0

7 : H i g h e r
A : L o w e r
- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 168
18. Press “C” to confirm and save the setting, or press “A” to exit without sav-
C O N F I R M
ing.
- - - - - - - - - - - - - - - -

C - C o n f i r m
A - A b o r t

- - - - - - - - - - - - - - - -

Fig. 168

20-54
Calibrations and electronic
diagnosis
20.3.9 - Renewal of the shuttle ECU - Editing the comfort parameters (AGROFARM 410
-> ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)
1. To access the menu for editing the comfort parameters, select “3 - Comfort
C A L I B R . R E V E R S E R
param” from the main calibration menu “Calibr. Reverser”.
- - - - - - - - - - - - - - - -

1 - A u t o m a t i c
2 - M a n u a l
3 - C o m f o r t p a r a m

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 169
2. The parameters are divided into the three possible manoeuvres and have
C O M F O R T P A R A M
the following meanings:
= = = = = = = = = = = = = = = =
m “Response”: determines the initial response of the clutches in the = = = = = = S t a r t = = = = =
various manoeuvres, in the stage immediately subsequent to the 1 - R e s p o n s e 3 0 0
2 - A c c e l e r a t 6 0 0
clutch fill time. Increase the setting to obtain a faster response (in = = = I n v e r s i o n = = = =
the case of delayed response, excessive initial clutch slip) and re- 3 - R e s p o n s e 4 5 0
duce the value if the clutch action is too sharp (sudden and jerky). 4 - A c c e l e r a t 7 5 0
m “Acceleration”: determines the speed at which the tractor performs = = = G e a r C h a n g e = = =
5 - R e s p o n s e 4 2 0
manoeuvres. The value should be increased to increase the speed 6 - A c c e l e r a t 1 0 0 0
at which manoeuvres are performed. = = = = = P e d a l = = = = = =
7 - I n c h i n g P o + 0
The “InchingPo” parameter represents the position of the pedal at which
the clutch starts to bites on releasing the pedal. - - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 170
3. The higher the value the higher the clutch biting point; to lower the clutch
7 - I n c h i n g P o
biting point a negative value must be entered.
- - - - - - - - - - - - - - - -
To enter negative numbers, proceed as follows:
m Press “7” to edit the “InchingPo” parameter.
m The following screen appears:
A c t u a l : 0

N e w : + _

[ B ] T o g g l e + -
[ D ] D e l e t e
[ E ] E x i t

Fig. 171

20-55
 Calibrations and electronic
diagnosis
4. Press [B] “Toggle + -” to change the sign of the value entered.
Set the desired value, press [E] and press [C] to confirm.
N e w : + 5 0

[ B ] T o g g l e + -

N e w : - 5 0

Fig. 172

20.3.10 - Replacing the electronic lift ECU - Basic commissioning procedure (AGRO-
FARM 410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGRO-
FARM 430 -> ZKDW550200TD30001)
1. The steps of the commissioning activation procedure are as follows:
A V A I L A B L E T E S T
m Shut off the engine, put the main gearbox and range gearbox in M E N U
neutral.
m Connect the A.R.T. instrument to the diagnostic socket.
m Turn the ignition switch to “ON”.
1 - H L H P E X P L O R E R
m Select SMART LEVER from the list of connected ECUs.

C H O I C E
[ E ] E x i t

Fig. 173
2. From the welcome screen, press 0 twice
= = = = = = = = = = = = = = = =
= = = = = H L H P = = = = =
= = = = = = = = = = = = = = = =

S W V e r s i o n
S C 1 1 7 A B

D a t e :
1 6 - 0 3 - 2 0 1 2

C o n f i g u r a t i o n
T 5 1 0 0 1 0 5 / 1 1 0 C V

[ E ] E x i t

Fig. 174

20-56
Calibrations and electronic
diagnosis
3. A password prompt will appear. Enter the password.

P a s s w o r d : * * * * * *

Fig. 175
4. On entering the password, the introductory screen will re-appear. Press [E]
M A I N M E N U
to enter the main menu. If the password is entered correctly, the option “C-
- - - - - - - - - - - - - - - -
Initialize” (normally hidden) will be displayed
1 - M o n i t o r s
2 - P a r a m e t e r s
3 - C a l i b r a t i o n s
4 - A l a r m s

C - I n i t i a l i z a t i o n

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 176
5. Press [C] to activate the machine commissioning procedure. The following
I N I T I A L I Z A T I O N
menu is displayed on the SAME ART instrument:
- - - - - - - - - - - - - - - -
M A C H I N E
S T A R T U P

- - - - - - - - - - - - - - - -
1 - R e p r o g . E e p r o m
2 - M a c h . S t a r t - U p
- - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 177
6. If necessary, re-initialise the eeprom as instructed in the following paragraph
See para. 20.3.11 - Replacing the electron... - page 20-58
otherwise go to paragraph
See para. 20.3.12 - Replacing the electron... - page 20-58

20-57
 Calibrations and electronic
diagnosis
20.3.11 - Replacing the electronic lift ECU - EEPROM re-initialisation (AGROFARM 410
-> ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)
1. Perform the steps described in chapter
See para. 20.3.10 - Replacing the electron... - page 20-56
On selecting option [1] a warning message appears.
If you continue with the procedure, the Eeprom will be re-initialised and the parameter values in memory will be overwritten
with the default values.
2. Press [E] to cancel or [C] to continue with the re-initialisation procedure.
R E I N I T . E E P R O M
- - - - - - - - - - - - - - - -

= = = = = = = = = = = = = = = =
! A T T E N T I O N !
T H E M E M O R Y W I L L
B E C O M P L E T E L Y
R E P R O G R A M M E D
= = = = = = = = = = = = = = = =
P R E S S [ C ]
T O C O N T I N U E

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 178
3. Wait. On termination of the re-initialisation procedure the following mes-
R E I N I T . E E P R O M
sage is displayed.
- - - - - - - - - - - - - - - -

M E M O R Y
R E I N I T I A L I S E D
C O R R E C T L Y

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 179
4. Eeprom re-initialisation in now complete. Press [E] to return to the main commissioning menu.

20.3.12 - Replacing the electronic lift ECU - End-of-line tractor programming (AGRO-
FARM 410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGRO-
FARM 430 -> ZKDW550200TD30001)
1. The end-of-line programming procedure consists of following steps:
m Configuration of the model
m Option selection

20-58
Calibrations and electronic
diagnosis
2. To perform the commissioning procedure, repeat the steps described in
I N I T I A L I Z A T I O N
chapter
See para. 20.3.10 - Replacing the electron... - page 20-56 - - - - - - - - - - - - - - - -
M A C H I N E
S T A R T U P

- - - - - - - - - - - - - - - -
1 - R e p r o g . E e p r o m
2 - M a c h . S t a r t - U p
- - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 180
3. Press [2] to activate the commissioning procedure. A warning message will be displayed.
DANGER
It will not be possible to use the machine until the commissioning procedure has been completed. If the ma-
chine is switched off before the procedure has terminated, it will be necessary to repeat the commissioning
procedure.
4. Press [C] to activate the line end programming procedure.
! ! A T T E N T I O N ! !
- - - - - - - - - - - - - - - -

T H E M A C H I N E
C A N N O T B E U S E D
U N T I L T H E E N D
O F T H E P R O C E D U R E

- - - - - - - - - - - - - - - -

P R E S S [ C ] T O
C O N T I N U E

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 181
5. As soon as line end programming is activated, the family configuration
C O N F I G U R E F A M I L
page appears on the ART.
- - - - - - - - - - - - - - - -
Select the option “1 - EXPLORER3”, then press “E” to exit and “C” to con-
1 - T y p e F a m i l y 1
firm and access the next screen.
Note
1 : E X P L O R E R 3
If the tractor family proposed is not correct, or if no family is
proposed (0), press [1] to select the family. In this case, as
this is an EXPLORER³ family machine, select [1].

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 182

20-59
 Calibrations and electronic
diagnosis
6. Once family configuration has been completed, the ART will display the
E N G I N E M O D E L
engine selection page.
- - - - - - - - - - - - - - - -
Press [1] to select the engine model installed in the machine. 1 - E n g i n e T i p e 0
Press [C] to confirm the selection and return to the model selection menu,
then press [E] to continue with line end programming. 1 - S A M E
2 - D E U T Z

[ E ] E x i t
[ C ] S t o r e

Fig. 183
7. The options page will appear. To make changes, press the button corre-
O P T I O N S
sponding to the option that you wish to edit.
- - - - - - - - - - - - - - - -
Table 28
1 : P T O A n t e r . 0
2 : D i s t . A u x 0
OPTION DESCRIPTION 3 : A b i l i a z . D T 1
Front PTO Enable front PTO (Default setting
disabled=0)
Aux. Dist. Enable auxiliary distributor (Default
setting disabled = 0)
Enable DT Enable DT function:
0= DT absent (for 2WD models)
1= Electrohydraulic DT present (De-
[ E ] E x i t
fault)
2 = Mechanical DT present [ C ] S t o r e

Fig. 184
8. If the procedure was successful, a screen confirming the configuration will
! ! A T T E N T I O N ! !
be displayed.
- - - - - - - - - - - - - - - -
Press “E” to return to the main menu.
Turn the ignition switch to “O” (OFF) then back to “I” (ON) and perform the
procedure to calibrate the reverse shuttle clutches. M A C H I N E
S T A R T - U P
E N D E D
S U C C E S S F U L L Y

= = = = = = = = = = = = = = = =

R E S T A R T
T H E E N G I N E

[ E ] E x i t

Fig. 185

20-60
Calibrations and electronic
diagnosis
20.3.13 - Replacing the electronic lift ECU - Lift calibration (AGROFARM 410 -> ZKD-
W470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)
1. Select “3” “Calibrations” from the main menu.
M A I N M E N U
- - - - - - - - - - - - - - - -
1 - M o n i t o r s
2 - P a r a m e t e r s
3 - C a l i b r a t i o n s
4 - A l a r m s

C - I n i t i a l i z a t i o n

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 186
2. Press [2] to access the “Lift” menu.
C A L I B R A Z I O NI
- - - - - - - - - - - - - - - -

2 - S o l l e v a t o r e
3 - P T O
4 - A S M

6 - D i s t . A u x
7 - S i s t e m a

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 187
3. Press “2” to access the “Calibrations” / Calibrations menu.
M E N U P A R A M E T R I
- - - - - - - - - - - - - - - -
1 - O p t i o n s
2 - C a l i b r a t i o n s

4 - J o y s t i c k C a l i b .
5 - J o y s t i c k C o n f i g

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 188

20-61
 Calibrations and electronic
diagnosis
4. Release the lift.
M E N U C A L I B R A Z I O N I
Select “1” and calibrate the minimum lift height position. Manoeuvre the lift
- - - - - - - - - - - - - - - -
into the lowest desired position. 1 - A l t . M i n . 0 . 6 2
Select “2” to calibrate the maximum lift height position. Manoeuvre the lift 2 - A l t . M a s s . 4 . 3 6
into the highest desired position.
Press “E” to end calibration and exit. 4 - C o n t r . M a n u a l e

- - - - - - - - - - - - - - - -
[ E ] E x i t

Fig. 189

20-62
Calibrations and electronic
diagnosis
20.4 - ECU alarms
20.4.1 - Engine alarms
Alarms - Engine alarms list (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 420 -> ZKD-
W390200TD25001)
Table 29
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
91 2 M5 MEDIUM H014 - Accel- Accelerator pedal poten- Check sensor cable. 40-701
erator pedal tiometer fault
H018 - Accel- Check and if necessary 40-705
erator pedal replace sensor.
H026 - Accel- 40-714
erator pedal
H030 - Accel- 40-719
erator pedal
91 11 M67 MEDIUM H014 - Accel- Connection error with ac- Check sensor cable. 40-701
erator pedal celerator pedal position
H018 - Accel- sensor Check and if necessary 40-705
erator pedal replace sensor.
H026 - Accel- 40-714
erator pedal
H030 - Accel- 40-719
erator pedal
102 2 M7 MEDIUM K032 - Turbine Intake manifold air pres- Check sensor cable. 40-701
air temperature/ sure sensor Check and if necessary 40-705
pressure sensor replace sensor. 40-714
40-719
105 2 M10 MEDIUM K032 - Turbine Air supply temperature Check sensor cable. 40-701
air temperature/ sensor Check and if necessary 40-705
pressure sensor replace sensor. 40-714
40-719
108 12 M87 LOW Atmospheric pressure Check power voltage.
not within permissible Switch off and switch on
range. again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
110 0 M31 MEDIUM K030 - Engine Coolant temperature Check coolant. 40-701
coolant temper- above alarm threshold. Check temperature sen- 40-705
ature sensor sor and wiring. 40-714
40-719
110 0 M41 HIGH K030 - Engine Coolant temperature Check coolant. 40-701
coolant temper- above cut-out limit Check coolant tempera- 40-705
ature sensor ture sensor and wiring.
Check cut-out limit. 40-714
40-719
110 2 M9 MEDIUM K030 - Engine Coolant temperature Check sensor cable. 40-701
coolant temper- sensor Check and if necessary 40-705
ature sensor replace sensor. 40-714
40-719

20-63
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
171 12 M86 LOW M002/M003 - Internal temperature Check power voltage. 40-701
Engine ECU within ECU too high.
M007/M008 - Switch off and switch on 40-705
Engine ECU again.
M013/M014 - Re-check. In the case of 40-714
Engine ECU a fault, inform the DEUTZ
M017/M018 - Service Organisation. 40-719
Engine ECU
174 0 M36 MEDIUM K036 - Fuel tem- Fuel temperature above Check fuel. 40-701
perature sensor alarm threshold. Check fuel temperature 40-705
sensor and wiring. 40-714
40-719
174 2 M11 MEDIUM K032 - Fuel tem- Fuel temperature sensor Check sensor cable. 40-701
perature sensor Check and if necessary 40-705
replace sensor. 40-714
40-719
190 8 M1 HIGH K035 - Cam- Engine speed sensor Check gap. 40-701
shaft speed faulty Check wiring connec- 40-705
sensor tions.
Check and if necessary 40-714
replace sensor. 40-719
201 2 M6 MEDIUM H013 - Hand Hand throttle fault Check sensor cable. 40-701
throttle position
sensor
H017 - Hand Check and if necessary 40-705
throttle position replace sensor.
sensor
H025 - Hand 40-714
throttle position
sensor
H029 - Hand 40-719
throttle position
sensor

20-64
Calibrations and electronic
diagnosis
Table 30
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
535 7 M53 HIGH N013 - Actuator Mechanical governor Check actuator and re- 40-701
fault place if necessary.
Check wiring. 40-705
40-714
40-719
536 12 M50 HIGH N013 - Actuator Actuator faulty Check actuator and re- 40-701
place if necessary.
Check wiring. 40-705
40-714
40-719
536 13 M52 HIGH N013 - Actuator Actuator not calibrated Check actuator and re- 40-701
place if necessary.
Check wiring. 40-705
40-714
40-719
702 14 M35 MEDIUM Engine overspeed Check parameter (21)
Check speed governor.
Check speed sensor
743 9 M71 MEDIUM Transmission error on Check CAN connection, 40-1247
CANBUS line. terminal resistor.
Check ECU. 40-1255
743 12 M70 MEDIUM CANBUS line controller Check CAN connection, 40-1247
damaged terminal resistor.
Check ECU. 40-1255
743 14 M74 MEDIUM Transmission error on Check CAN connection, 40-1247
CANBUS line. terminal resistor.
Check ECU. 40-1255
752 2 M93 HIGH “Stack Overflow” error Switch off and switch on
during programme ex- again.
ecution. Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
752 12 M77 HIGH Engine ECU identified a Switch off and switch on
programme memory er- again.
ror during normal check Re-check.
cycle. In the case of a fault, in-
form the DEUTZ Service
Organisation.
765 2 M90 HIGH Inconsistency with pa- Check that the param-
rameters written in EE- eters are configured cor-
PROM memory. rectly.
Save parameters, switch
off and switch on again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
765 12 M76 HIGH Error identified during pa- Switch off and switch on
rameter write on ECU again.
Re-check.
In the case of a fault, in-
form the DEUTZ Service
Organisation.

20-65
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
766 2 M78 HIGH Engine ECU identified a Switch off and switch on
programme memory er- again.
ror during normal check Re-check.
cycle. In the case of a fault, in-
form the DEUTZ Service
Organisation.
Table 31
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
766 2 M80 LOW Actuator power feed not Switch off and switch on 40-701
within permissible pa- again.
rameters. Re-check. 40-705
In the case of a fault, in- 40-714
form the DEUTZ Service 40-719
Organisation.
766 2 M83 LOW Accelerator pedal posi- Check power voltage. 40-701
tion sensor power feed Switch off and switch on 40-705
absent or incorrect. again. Re-check.
In the case of a fault, in- 40-714
form the DEUTZ Service 40-719
Organisation.
766 2 M84 LOW Engine boost pressure Check power voltage. 40-701
sensor power feed ab- Switch off and switch on 40-705
sent or incorrect. again.
Re-check. In the case of 40-714
a fault, inform the DEUTZ 40-719
Service Organisation.
766 2 M94 HIGH Internal error. Check power voltage.
Switch off and switch on
again.
898 2 M68 MEDIUM Connection error with Check CAN connection, 40-1247
CANBUS line terminal resistor.
Check ECU. 40-1255

20-66
Calibrations and electronic
diagnosis
Alarms - Engine alarms list (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKD-
W510200TD30001)
Table 32
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
91 2 M5 MEDIUM H014 - Accel- Accelerator pedal poten- Check sensor cable. 40-701
erator pedal tiometer fault
H018 - Accel- Check and if necessary 40-705
erator pedal replace sensor.
H026 - Accel- 40-714
erator pedal
H030 - Accel- 40-719
erator pedal
91 11 M67 MEDIUM H014 - Accel- Connection error with ac- Check sensor cable. 40-701
erator pedal celerator pedal position
H018 - Accel- sensor Check and if necessary 40-705
erator pedal replace sensor.
H026 - Accel- 40-714
erator pedal
H030 - Accel- 40-719
erator pedal
102 2 M7 MEDIUM K032 - Turbine Intake manifold air pres- Check sensor cable. 40-701
air temperature/ sure sensor Check and if necessary 40-705
pressure sensor replace sensor. 40-714
40-719
105 2 M10 MEDIUM K032 - Turbine Air supply temperature Check sensor cable. 40-701
air temperature/ sensor Check and if necessary 40-705
pressure sensor replace sensor. 40-714
40-719
108 12 M87 LOW Atmospheric pressure Check power voltage.
not within permissible Switch off and switch on
range. again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
110 0 M31 MEDIUM K030 - Engine Coolant temperature Check coolant. 40-701
coolant temper- above alarm threshold. Check temperature sen- 40-705
ature sensor sor and wiring. 40-714
40-719
110 0 M41 HIGH K030 - Engine Coolant temperature Check coolant. 40-701
coolant temper- above cut-out limit Check coolant tempera- 40-705
ature sensor ture sensor and wiring.
Check cut-out limit. 40-714
40-719
110 2 M9 MEDIUM K030 - Engine Coolant temperature Check sensor cable. 40-701
coolant temper- sensor Check and if necessary 40-705
ature sensor replace sensor. 40-714
40-719

20-67
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
171 12 M86 LOW M002/M003 - Internal temperature Check power voltage. 40-701
Engine ECU within ECU too high.
M007/M008 - Switch off and switch on 40-705
Engine ECU again.
M013/M014 - Re-check. In the case of 40-714
Engine ECU a fault, inform the DEUTZ
M017/M018 - Service Organisation. 40-719
Engine ECU
174 0 M36 MEDIUM K036 - Fuel tem- Fuel temperature above Check fuel. 40-701
perature sensor alarm threshold. Check fuel temperature 40-705
sensor and wiring. 40-714
40-719
174 2 M11 MEDIUM K032 - Fuel tem- Fuel temperature sensor Check sensor cable. 40-701
perature sensor Check and if necessary 40-705
replace sensor. 40-714
40-719
190 8 M1 HIGH K035 - Cam- Engine speed sensor Check gap. 40-701
shaft speed faulty Check wiring connec- 40-705
sensor tions.
Check and if necessary 40-714
replace sensor. 40-719
201 2 M6 MEDIUM H013 - Hand Hand throttle fault Check sensor cable. 40-701
throttle position
sensor
H017 - Hand Check and if necessary 40-705
throttle position replace sensor.
sensor
H025 - Hand 40-714
throttle position
sensor
H029 - Hand 40-719
throttle position
sensor

20-68
Calibrations and electronic
diagnosis
Table 33
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
535 7 M53 HIGH N013 - Actuator Mechanical governor Check actuator and re- 40-701
fault place if necessary.
Check wiring. 40-705
40-714
40-719
536 12 M50 HIGH N013 - Actuator Actuator faulty Check actuator and re- 40-701
place if necessary.
Check wiring. 40-705
40-714
40-719
536 13 M52 HIGH N013 - Actuator Actuator not calibrated Check actuator and re- 40-701
place if necessary.
Check wiring. 40-705
40-714
40-719
702 14 M35 MEDIUM Engine overspeed Check parameter (21)
Check speed governor.
Check speed sensor
743 9 M71 MEDIUM Transmission error on Check CAN connection, 40-1250
CANBUS line. terminal resistor.
Check ECU. 40-1258
743 12 M70 MEDIUM CANBUS line controller Check CAN connection, 40-1250
damaged terminal resistor.
Check ECU. 40-1258
743 14 M74 MEDIUM Transmission error on Check CAN connection, 40-1250
CANBUS line. terminal resistor.
Check ECU. 40-1258
752 2 M93 HIGH “Stack Overflow” error Switch off and switch on
during programme ex- again.
ecution. Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
752 12 M77 HIGH Engine ECU identified a Switch off and switch on
programme memory er- again.
ror during normal check Re-check.
cycle. In the case of a fault, in-
form the DEUTZ Service
Organisation.
765 2 M90 HIGH Inconsistency with pa- Check that the param-
rameters written in EE- eters are configured cor-
PROM memory. rectly.
Save parameters, switch
off and switch on again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
765 12 M76 HIGH Error identified during pa- Switch off and switch on
rameter write on ECU again.
Re-check.
In the case of a fault, in-
form the DEUTZ Service
Organisation.

20-69
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
766 2 M78 HIGH Engine ECU identified a Switch off and switch on
programme memory er- again.
ror during normal check Re-check.
cycle. In the case of a fault, in-
form the DEUTZ Service
Organisation.
Table 34
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
766 2 M80 LOW Actuator power feed not Switch off and switch on 40-701
within permissible pa- again.
rameters. Re-check. 40-705
In the case of a fault, in- 40-714
form the DEUTZ Service 40-719
Organisation.
766 2 M83 LOW Accelerator pedal posi- Check power voltage. 40-701
tion sensor power feed Switch off and switch on 40-705
absent or incorrect. again. Re-check.
In the case of a fault, in- 40-714
form the DEUTZ Service 40-719
Organisation.
766 2 M84 LOW Engine boost pressure Check power voltage. 40-701
sensor power feed ab- Switch off and switch on 40-705
sent or incorrect. again.
Re-check. In the case of 40-714
a fault, inform the DEUTZ 40-719
Service Organisation.
766 2 M94 HIGH Internal error. Check power voltage.
Switch off and switch on
again.
898 2 M68 MEDIUM Connection error with Check CAN connection, 40-1250
CANBUS line terminal resistor.
Check ECU. 40-1258
Alarms - Engine alarms list (AGROFARM 430 -> ZKDW430200TD25001)
Table 35
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
91 2 M5 MEDIUM H022 - Accel- Accelerator pedal poten- Check sensor cable. 40-710
erator pedal tiometer fault Check and if necessary
replace sensor.

20-70
Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
91 11 M67 MEDIUM H022 - Accel- Connection error with ac- Check sensor cable. 40-710
erator pedal celerator pedal position Check and if necessary
sensor replace sensor.
102 2 M7 MEDIUM K032 - Turbine Intake manifold air pres- Check sensor cable. 40-710
air temperature/ sure sensor Check and if necessary
replace sensor.
105 2 M10 MEDIUM K032 - Turbine Air supply temperature Check sensor cable. 40-710
air temperature/ sensor Check and if necessary
replace sensor.
108 12 M87 LOW Atmospheric pressure Check power voltage.
not within permissible Switch off and switch on
range. again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
110 0 M31 MEDIUM K030 - Engine Coolant temperature Check coolant. 40-710
coolant temper- above alarm threshold. Check temperature sen-
sor and wiring.
110 0 M41 HIGH K030 - Engine Coolant temperature Check coolant. 40-710
coolant temper- above cut-out limit Check coolant tempera-
ature sensor ture sensor and wiring.
Check cut-out limit.
110 2 M9 MEDIUM K030 - Engine Coolant temperature Check sensor cable. 40-710
coolant temper- sensor Check and if necessary
replace sensor.
171 12 M86 LOW M009/M010 - Internal temperature Check power voltage. 40-710
Engine ECU within ECU too high. Switch off and switch on
again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
174 0 M36 MEDIUM K036 - Fuel tem- Fuel temperature above Check fuel. 40-710
perature sensor alarm threshold. Check fuel temperature
sensor and wiring.
174 2 M11 MEDIUM K036 - Fuel tem- Fuel temperature sensor Check sensor cable. 40-710
perature sensor Check and if necessary
replace sensor.
190 8 M1 HIGH K035 - Cam- Engine speed sensor Check gap. 40-710
shaft speed faulty Check wiring connec-
sensor tions.
Check and if necessary
replace sensor.
201 2 M6 MEDIUM H021 - Hand Hand throttle fault Check sensor cable. 40-710
throttle position Check and if necessary
replace sensor.

20-71
 Calibrations and electronic
diagnosis
Table 36
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
535 7 M53 HIGH N013 - Actuator Mechanical governor Check actuator and re- 40-710
fault place if necessary.
Check wiring.
536 12 M50 HIGH N013 - Actuator Actuator faulty Check actuator and re- 40-710
place if necessary.
Check wiring.
536 13 M52 HIGH N013 - Actuator Actuator not calibrated Check actuator and re- 40-710
place if necessary.
Check wiring.
702 14 M35 MEDIUM Engine overspeed Check parameter (21)
Check speed governor.
Check speed sensor
743 9 M71 MEDIUM Transmission error on Check CAN connection, 40-1262
CANBUS line. terminal resistor.
Check ECU.
743 12 M70 MEDIUM CANBUS line controller Check CAN connection, 40-1262
damaged terminal resistor.
Check ECU.
743 14 M74 MEDIUM Transmission error on Check CAN connection, 40-1262
CANBUS line. terminal resistor.
Check ECU.
752 2 M93 HIGH “Stack Overflow” error Switch off and switch on
during programme ex- again.
ecution. Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
752 12 M77 HIGH Engine ECU identified a Switch off and switch on
programme memory er- again.
ror during normal check Re-check.
cycle. In the case of a fault, in-
form the DEUTZ Service
Organisation.
765 2 M90 HIGH Inconsistency with pa- Check that the param-
rameters written in EE- eters are configured cor-
PROM memory. rectly.
Save parameters, switch
off and switch on again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
765 12 M76 HIGH Error identified during pa- Switch off and switch on
rameter write on ECU again.
Re-check.
In the case of a fault, in-
form the DEUTZ Service
Organisation.
766 2 M78 HIGH Engine ECU identified a Switch off and switch on
programme memory er- again.
ror during normal check Re-check.
cycle. In the case of a fault, in-
form the DEUTZ Service
Organisation.

20-72
Calibrations and electronic
diagnosis
Table 37
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
766 2 M80 LOW Actuator power feed not Switch off and switch on 40-710
within permissible pa- again.
rameters. Re-check.
In the case of a fault, in-
form the DEUTZ Service
Organisation.
766 2 M83 LOW Accelerator pedal posi- Check power voltage. 40-710
tion sensor power feed Switch off and switch on
absent or incorrect. again. Re-check.
In the case of a fault, in-
form the DEUTZ Service
Organisation.
766 2 M84 LOW Engine boost pressure Check power voltage. 40-710
sensor power feed ab- Switch off and switch on
sent or incorrect. again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
766 2 M94 HIGH Internal error. Check power voltage.
Switch off and switch on
again.
898 2 M68 MEDIUM Connection error with Check CAN connection, 40-1262
CANBUS line terminal resistor.
Check ECU.
Alarms - Engine alarms list (AGROFARM 430 -> ZKDW550200TD30001)
Table 38
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
91 2 M5 MEDIUM H022 - Accel- Accelerator pedal poten- Check sensor cable. 40-710
erator pedal tiometer fault Check and if necessary
replace sensor.
91 11 M67 MEDIUM H022 - Accel- Connection error with ac- Check sensor cable. 40-710
erator pedal celerator pedal position Check and if necessary
replace sensor.
102 2 M7 MEDIUM K032 - Turbine Intake manifold air pres- Check sensor cable. 40-710
air temperature/ sure sensor Check and if necessary
replace sensor.
105 2 M10 MEDIUM K032 - Turbine Air supply temperature Check sensor cable. 40-710
air temperature/ sensor Check and if necessary
replace sensor.
108 12 M87 LOW Atmospheric pressure Check power voltage.
not within permissible Switch off and switch on
range. again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.

20-73
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
110 0 M31 MEDIUM K030 - Engine Coolant temperature Check coolant. 40-710
coolant temper- above alarm threshold. Check temperature sen-
sor and wiring.
110 0 M41 HIGH K030 - Engine Coolant temperature Check coolant. 40-710
coolant temper- above cut-out limit Check coolant tempera-
ature sensor ture sensor and wiring.
Check cut-out limit.
110 2 M9 MEDIUM K030 - Engine Coolant temperature Check sensor cable. 40-710
coolant temper- sensor Check and if necessary
replace sensor.
171 12 M86 LOW M009/M010 - Internal temperature Check power voltage. 40-710
Engine ECU within ECU too high. Switch off and switch on
again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
174 0 M36 MEDIUM K036 - Fuel tem- Fuel temperature above Check fuel. 40-710
perature sensor alarm threshold. Check fuel temperature
sensor and wiring.
174 2 M11 MEDIUM K036 - Fuel tem- Fuel temperature sensor Check sensor cable. 40-710
perature sensor Check and if necessary
replace sensor.
190 8 M1 HIGH K035 - Cam- Engine speed sensor Check gap. 40-710
shaft speed faulty Check wiring connec-
sensor tions.
Check and if necessary
replace sensor.
201 2 M6 MEDIUM H021 - Hand Hand throttle fault Check sensor cable. 40-710
throttle position Check and if necessary
replace sensor.

20-74
Calibrations and electronic
diagnosis
Table 39
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
535 7 M53 HIGH N013 - Actuator Mechanical governor Check actuator and re- 40-710
fault place if necessary.
Check wiring.
536 12 M50 HIGH N013 - Actuator Actuator faulty Check actuator and re- 40-710
place if necessary.
Check wiring.
536 13 M52 HIGH N013 - Actuator Actuator not calibrated Check actuator and re- 40-710
place if necessary.
Check wiring.
702 14 M35 MEDIUM Engine overspeed Check parameter (21)
Check speed governor.
Check speed sensor
743 9 M71 MEDIUM Transmission error on Check CAN connection, 40-1266
CANBUS line. terminal resistor.
Check ECU.
743 12 M70 MEDIUM CANBUS line controller Check CAN connection, 40-1266
damaged terminal resistor.
Check ECU.
743 14 M74 MEDIUM Transmission error on Check CAN connection, 40-1266
CANBUS line. terminal resistor.
Check ECU.
752 2 M93 HIGH “Stack Overflow” error Switch off and switch on
during programme ex- again.
ecution. Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
752 12 M77 HIGH Engine ECU identified a Switch off and switch on
programme memory er- again.
ror during normal check Re-check.
cycle. In the case of a fault, in-
form the DEUTZ Service
Organisation.
765 2 M90 HIGH Inconsistency with pa- Check that the param-
rameters written in EE- eters are configured cor-
PROM memory. rectly.
Save parameters, switch
off and switch on again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
765 12 M76 HIGH Error identified during pa- Switch off and switch on
rameter write on ECU again.
Re-check.
In the case of a fault, in-
form the DEUTZ Service
Organisation.
766 2 M78 HIGH Engine ECU identified a Switch off and switch on
programme memory er- again.
ror during normal check Re-check.
cycle. In the case of a fault, in-
form the DEUTZ Service
Organisation.

20-75
 Calibrations and electronic
diagnosis
Table 40
ART code In- Severity Component Fault Checks Link to sys-
Spn Fmi stru- tem
ment
panel
dis-
play
error
766 2 M80 LOW Actuator power feed not Switch off and switch on 40-710
within permissible pa- again.
rameters. Re-check.
In the case of a fault, in-
form the DEUTZ Service
Organisation.
766 2 M83 LOW Accelerator pedal posi- Check power voltage. 40-710
tion sensor power feed Switch off and switch on
absent or incorrect. again. Re-check.
In the case of a fault, in-
form the DEUTZ Service
Organisation.
766 2 M84 LOW Engine boost pressure Check power voltage. 40-710
sensor power feed ab- Switch off and switch on
sent or incorrect. again.
Re-check. In the case of
a fault, inform the DEUTZ
Service Organisation.
766 2 M94 HIGH Internal error. Check power voltage.
Switch off and switch on
again.
898 2 M68 MEDIUM Connection error with Check CAN connection, 40-1266
CANBUS line terminal resistor.
Check ECU.

20.4.2 - Instrument panel alarms

Alarms - Instrument alarms list (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 420 -> ZKD-
W390200TD25001)
Table 41
Instru- Severity Component Fault Checks Link to system
ment
panel
display
error
I 18 Low - Temperature sensor short cir- - -
cuit to earth
I 19 Low - Temperature sensor power - -
supply short circuit
I 20 Low K016 - Fuel level Fuel level sensor short circuit - 40-791
sensor to battery 40-807
40-826
40-843
I 21 Low - Frequency sensor 1 not con- - -
nected
I 22 Low - Frequency sensor 2 not con- - -
nected
I 23 Low - Power output 0 disconnected - -
I 24 Low - Power output 0 short circuit - -
to earth
I 25 Low - Power output 0 short circuit - -
to battery

20-76
Calibrations and electronic
diagnosis
Instru- Severity Component Fault Checks Link to system
ment
panel
display
error
I 26 Low - Power output 0 short circuit - -
to battery or open circuit
I 32 Low - Power output 1 disconnected - -
I 33 Low - Power output 1 short circuit - -
to earth
I 34 Low - Power output 1 short circuit - -
to battery
I 35 Low - Power output 1 short circuit - -
to battery or open circuit
I 36 High - Relay short circuit (preheat- - -
ing function)
I 37 Low - Relay faulty (preheating func- - -
tion)
I 38 Medium - Seat sensor S.C. to earth - -
I 39 Medium - Seat sensor S.C. to Vdc - -
I 40 Medium - Seat sensor out of range - -
Alarms - Instrument alarms list (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKD-
W510200TD30001)
Table 42
Instru- Severity Component Fault Checks Link to system
ment
panel
display
error
I 18 Low - Temperature sensor short cir- - -
cuit to earth
I 19 Low - Temperature sensor power - -
supply short circuit
I 20 Low K016 - Fuel level Fuel level sensor short circuit - 40-799
sensor to battery 40-816
40-834
40-852
I 21 Low - Frequency sensor 1 not con- - -
nected
I 22 Low - Frequency sensor 2 not con- - -
nected
I 23 Low - Power output 0 disconnected - -
I 24 Low - Power output 0 short circuit - -
to earth
I 25 Low - Power output 0 short circuit - -
to battery
I 26 Low - Power output 0 short circuit - -
to battery or open circuit
I 32 Low - Power output 1 disconnected - -
I 33 Low - Power output 1 short circuit - -
to earth
I 34 Low - Power output 1 short circuit - -
to battery
I 35 Low - Power output 1 short circuit - -
to battery or open circuit
I 36 High - Relay short circuit (preheat- - -
ing function)
I 37 Low - Relay faulty (preheating func- - -
tion)

20-77
 Calibrations and electronic
diagnosis
Instru- Severity Component Fault Checks Link to system
ment
panel
display
error
I 38 Medium - Seat sensor S.C. to earth - -
I 39 Medium - Seat sensor S.C. to Vdc - -
I 40 Medium - Seat sensor out of range - -
Alarms - Instrument alarms list (AGROFARM 430 -> ZKDW430200TD25001)
Table 43
Instru- Severity Component Fault Checks Link to system
ment
panel
display
error
I 18 Low - Temperature sensor short cir- - -
cuit to earth
I 19 Low - Temperature sensor power - -
supply short circuit
I 20 Low K048 - Fuel level Fuel level sensor short circuit - 40-862
sensor to battery
I 21 Low - Frequency sensor 1 not con- - -
nected
I 22 Low - Frequency sensor 2 not con- - -
nected
I 23 Low - Power output 0 disconnected - -
I 24 Low - Power output 0 short circuit - -
to earth
I 25 Low - Power output 0 short circuit - -
to battery
I 26 Low - Power output 0 short circuit - -
to battery or open circuit
I 32 Low - Power output 1 disconnected - -
I 33 Low - Power output 1 short circuit - -
to earth
I 34 Low - Power output 1 short circuit - -
to battery
I 35 Low - Power output 1 short circuit - -
to battery or open circuit
I 36 High - Relay short circuit (preheat- - -
ing function)
I 37 Low - Relay faulty (preheating func- - -
tion)
I 38 Medium - Seat sensor S.C. to earth - -
I 39 Medium - Seat sensor S.C. to Vdc - -
I 40 Medium - Seat sensor out of range - -
Alarms - Instrument alarms list (AGROFARM 430 -> ZKDW550200TD30001)
Table 44
Instru- Severity Component Fault Checks Link to system
ment
panel
display
error
I 18 Low - Temperature sensor short cir- - -
cuit to earth
I 19 Low - Temperature sensor power - -
supply short circuit

20-78
Calibrations and electronic
diagnosis
Instru- Severity Component Fault Checks Link to system
ment
panel
display
error
I 20 Low K048 - Fuel level Fuel level sensor short circuit - 40-870
sensor to battery
I 21 Low - Frequency sensor 1 not con- - -
nected
I 22 Low - Frequency sensor 2 not con- - -
nected
I 23 Low - Power output 0 disconnected - -
I 24 Low - Power output 0 short circuit - -
to earth
I 25 Low - Power output 0 short circuit - -
to battery
I 26 Low - Power output 0 short circuit - -
to battery or open circuit
I 32 Low - Power output 1 disconnected - -
I 33 Low - Power output 1 short circuit - -
to earth
I 34 Low - Power output 1 short circuit - -
to battery
I 35 Low - Power output 1 short circuit - -
to battery or open circuit
I 36 High - Relay short circuit (preheat- - -
ing function)
I 37 Low - Relay faulty (preheating func- - -
tion)
I 38 Medium - Seat sensor S.C. to earth - -
I 39 Medium - Seat sensor S.C. to Vdc - -
I 40 Medium - Seat sensor out of range - -

20.4.3 - Lift alarms

Alarms - Lift ECU alarms list (AGROFARM 430 -> ZKDW430200TD25001, AGROFARM 430 -> ZKD-
W550200TD30001)
Table 45
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
3 540 L04 Priority: LOW K043 - Rear lift ECU detects that the Check wiring 40-1269
draft sensor draft sensor is shorting to Check the sensor
battery positive. Check the sensor power
supply
Check sensor installation
4 540 L05 Priority: LOW K043 - Rear lift ECU detects that the Check wiring 40-1269
draft sensor draft sensor is shorting to Check the sensor
ground. Check the sensor power
supply
Check sensor installation
4 600 L 16 Priority: LOW M024 - Elec- The control unit detects - 40-1269
tronic lift con- that the lift control po-
sole tentiometer is shorting to
ground

20-79
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
3 600 L 17 Priority: LOW M024 - Elec- ECU detects that the - 40-1269
tronic lift con- lift control is shorting to
sole positive.
3 601 L 27 Priority: LOW K042 - Lift posi- The ECU detects that Check wiring 40-1269
tion sensor the lift position sensor is Check the sensor
shorting to positive. Check the sensor power
supply
Check sensor installation
4 601 L 28 Priority: LOW K042 - Lift posi- The control unit detects Check wiring 40-1269
tion sensor that the lift position sen- Check the sensor
sor is shorting to ground. Check the sensor power
supply
Check sensor installation
12 601 L 29 Priority: LOW K042 - Lift posi- The ECU detects an in- Check wiring 40-1269
tion sensor ternal fault in the ECU on Check the sensor
the input signal of the lift Check the sensor power
position sensor supply
Check sensor installation
3 602 L 30 Priority: LOW L011 - Lift up so- The control unit detects Check wiring 40-1269
lenoid valve that the lift ‘UP’ solenoid Check the valve
is shorting to positive. Check the valve power
supply
4 602 L 31 Priority: LOW L011 - Lift up so- The control unit detects Check wiring 40-1269
lenoid valve that the lift ‘UP’ solenoid Check the valve
is shorting to ground. Check the valve power
supply
5 602 L 32 Priority: LOW L011 - Lift up so- The ECU detects that the Check wiring 40-1269
lenoid valve current draw of the lift UP Check the valve
Check the valve power
supply

20-80
Calibrations and electronic
diagnosis
Table 46
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
6 602 L 33 Priority: LOW L011 - Lift up so- The ECU detects a short Check wiring 40-1269
lenoid valve circuit in the control wire Check the valve
of the lift ‘up’ solenoid Check the valve power
supply
3 603 L34 Priority: LOW L012 - Lift down The control unit detects Check wiring 40-1269
solenoid valve that the lift ‘DOWN’ so- Check the valve
Check the valve power
supply
4 603 L 35 Priority: LOW L012 - Lift down The ECU detects that Check wiring 40-1269
solenoid valve the lift DOWN solenoid is Check the valve
shorting to earth Check the valve power
supply
5 603 L 36 Priority: LOW L012 - Lift down The control unit detects Check wiring 40-1269
solenoid valve that the current draw of Check the valve
Check the valve power
supply
6 603 L37 Priority: LOW L012 - Lift down The ECU detects a short- Check wiring 40-1269
solenoid valve circuit in the control wire Check the valve
of the lift ‘down’ solenoid Check the valve power
supply
12 604 L 38 Priority: LOW M024 - Elec- The ECU has detected - 40-1269
tronic lift con- that the depth control po-
sole tentiometer is faulty
12 605 L 40 Priority: LOW M024 - Elec- The ECU has detected - 40-1269
tronic lift con- that the maximum height
sole potentiometer is faulty
12 606 L 42 Priority: LOW M024 - Elec- The ECU has detected - 40-1269
tronic lift con- that the descent speed
sole potentiometer is faulty
12 607 L 44 Priority: LOW M024 - Elec- The ECU has detected - 40-1269
tronic lift con- that the work mode con-
sole trol potentiometer is
faulty
4 690 L 87 Priority: LOW M024 - Elec- ECU detects a fault in - 40-1269
tronic lift con- the STOP position of the
sole main lever.
4 691 L 88 Priority: LOW M024 - Elec- ECU detects a fault in the - 40-1269
tronic lift con- TRANSPORT position of
sole the main lever.
4 692 L89 Priority: LOW M024 - Elec- ECU detects a fault in - 40-1269
tronic lift con- the CTRL position of the
sole main lever.
3 694 L 92 Priority: LOW I053/I054 - Ex- The ECU detects that the - 40-1269
ternal lift up con- lift ‘UP’ control buttons on
trol switch the rear fenders are con-
tinuously pressed
3 695 L 93 Priority: LOW I055/I056 - Ex- The ECU detects that the - 40-1269
ternal lift down lift ‘DOWN’ control but-
control switch tons on the rear fenders
are continuously pressed

20-81
 Calibrations and electronic
diagnosis
20.4.4 - HLHP alarms
Alarms - Services alarms list (AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKD-
W430200TD25001)
Table 47
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
12 664 U 01 - I023/I024 - Ex- ECU detects a PTO - 40-723
ternal PTO con- speed sensor fault
trol
I075/I076 - Ex- 40-738
ternal PTO con-
trol
I090/I091 - Ex- 40-743
ternal PTO con-
trol
3 662 U 02 - I023/I024 - Ex- The ECU detects that the - 40-723
ternal PTO con- rear PTO control buttons
trol on the mudguards are
I075/I076 - Ex- continuously pressed 40-738
ternal PTO con-
trol
I090/I091 - Ex- 40-743
ternal PTO con-
trol
3 697 U 03 - I032 - Rear PTO ECU detects that the rear - 40-723
switch PTO control button is
I040 - Rear PTO shorting to ground. 40-728
switch
I083 - Rear PTO 40-738
switch
I097 - Rear PTO 40-743
switch
3 698 U 04 - I022 - Front ECU detects that the - 40-723
PTO switch front PTO control button
I039 - Front is shorting to ground. 40-728
PTO switch
I085 - Front 40-738
PTO switch
I099 - Front 40-743
PTO switch
5 550 U 06 - L008 - Rear ECU detects that the rear - 40-723
PTO control so- PTO solenoid valve sole- 40-728
lenoid valve noid is not connected 40-738
40-743
4 550 U 07 - L008 - Rear ECU detects that the - 40-723
PTO control so- rear PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
ground.
3 550 U 08 - L008 - Rear ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
battery positive.

20-82
Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
5 551 U 09 - L001 - Front ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is not connected 40-738
40-743
4 551 U 10 - L001 - Front ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
ground.
3 551 U 11 - L001 - Front ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
battery positive.
5 653 U 12 - L001 - Front The ECU detects that the - 40-723
PTO control so- diff lock solenoid is not 40-728
lenoid valve connected 40-738
40-743
4 653 U 13 - L006 - Differen- The ECU detects that the - 40-1145
tial lock control differential lock solenoid 40-1166
solenoid valve is shorting to earth 40-1186
40-1206
3 653 U 14 - L006 - Differen- The control unit detects - 40-1145
tial lock control that the differential lock 40-1166
solenoid valve solenoid is shorting to 40-1186
40-1206
positive.
5 552 U 15 - L007 - 4WD The control unit detects - 40-1145
control solenoid that the 4WD engage- 40-1166
valve ment solenoid is not con- 40-1186
40-1206
nected
4 552 U 16 - L007 - 4WD The control unit detects - 40-1145
control solenoid that the 4WD solenoid is 40-1166
valve shorting to earth 40-1186
40-1206
3 552 U 17 - L007 - 4WD The control unit detects - 40-1145
control solenoid that the 4WD solenoid is 40-1166
valve shorting to battery posi- 40-1186
40-1206
tive
5 1,600 U 40 - ECU detects that the - 40-1237
rear EXTENDED (auxil- 40-1240
iary distributor) solenoid
valve solenoid is not con-
nected.
4 1,600 U 41 - ECU detects that the - 40-1237
rear EXTENDED (auxil- 40-1240
iary distributor) solenoid
valve solenoid is shorting
to ground
3 1,600 U 42 - ECU detects that the - 40-1237
rear EXTENDED (auxil- 40-1240
iary distributor) solenoid
valve solenoid is shorting
to battery positive

20-83
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
5 1601 U 43 - ECU detects that the - 40-1237
rear RETRACT (auxil- 40-1240
iary distributor) solenoid
valve solenoid is not con-
nected.
4 1601 U 44 - ECU detects that the rear - 40-1237
RETRACT (auxiliary dis- 40-1240
tributor) solenoid valve
solenoid is shorting to
ground
3 1601 U 45 - ECU detects that the rear - 40-1237
RETRACT (auxiliary dis- 40-1240
tributor) solenoid valve
solenoid is shorting to
battery positive
5 1602 U 46 - ECU detects that the rear - 40-1237
LOCK (auxiliary distribu- 40-1240
tor) solenoid valve sole-
noid is not connected.
4 1602 U 47 - ECU detects that the rear - 40-1237
LOCK (auxiliary distribu- 40-1240
tor) solenoid valve sole-
noid is shorting to ground
3 1602 U 48 - ECU detects that the rear - 40-1237
LOCK (auxiliary distribu- 40-1240
tor) solenoid valve sole-
noid is shorting to battery
positive

20-84
Calibrations and electronic
diagnosis
Alarms - Services alarms list (AGROFARM 430 -> ZKDW430200TD25001)
Table 48
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
12 664 U 01 - I049/I050 - Ex- ECU detects a PTO - 40-734
ternal PTO con- speed sensor fault
trol
3 662 U 02 - I049/I050 - Ex- The ECU detects that the - 40-734
ternal PTO con- rear PTO control buttons
trol on the mudguards are
continuously pressed
3 697 U 03 - I070 - Rear PTO ECU detects that the rear - 40-734
switch PTO control button is
shorting to ground.
3 698 U 04 - I071 - Front ECU detects that the - 40-734
PTO switch front PTO control button
is shorting to ground.
5 550 U 06 - L017 - Rear ECU detects that the rear - 40-734
PTO control so- PTO solenoid valve sole-
lenoid valve noid is not connected
4 550 U 07 - L017 - Rear ECU detects that the - 40-734
PTO control so- rear PTO solenoid valve
lenoid valve solenoid is shorting to
ground.
3 550 U 08 - L017 - Rear ECU detects that the - 40-734
PTO control so- front PTO solenoid valve
lenoid valve solenoid is shorting to
battery positive.
5 551 U 09 - L001 - Front ECU detects that the - 40-734
PTO control so- front PTO solenoid valve
lenoid valve solenoid is not connected
4 551 U 10 - L001 - Front ECU detects that the - 40-734
PTO control so- front PTO solenoid valve
lenoid valve solenoid is shorting to
ground.
3 551 U 11 - L001 - Front ECU detects that the - 40-734
PTO control so- front PTO solenoid valve
lenoid valve solenoid is shorting to
battery positive.
5 653 U 12 - L001 - Front The ECU detects that the - 40-734
PTO control so- diff lock solenoid is not
lenoid valve connected
4 653 U 13 - L019 - Differen- The ECU detects that the - 40-1226
tial lock control differential lock solenoid
solenoid valve is shorting to earth
3 653 U 14 - L019 - Differen- The control unit detects - 40-1226
tial lock control that the differential lock
solenoid valve solenoid is shorting to
positive.
5 552 U 15 - L018 - 4WD The control unit detects - 40-1226
control solenoid that the 4WD engage-
valve ment solenoid is not con-
nected

20-85
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
4 552 U 16 - L018 - 4WD The control unit detects - 40-1226
control solenoid that the 4WD solenoid is
valve shorting to earth
3 552 U 17 - L018 - 4WD The control unit detects - 40-1226
control solenoid that the 4WD solenoid is
valve shorting to battery posi-
tive
5 1,600 U 40 - ECU detects that the - 40-1243
rear EXTENDED (auxil-
iary distributor) solenoid
valve solenoid is not con-
nected.
4 1,600 U 41 - ECU detects that the - 40-1243
rear EXTENDED (auxil-
iary distributor) solenoid
valve solenoid is shorting
to ground
3 1,600 U 42 - ECU detects that the - 40-1243
rear EXTENDED (auxil-
iary distributor) solenoid
valve solenoid is shorting
to battery positive
5 1601 U 43 - ECU detects that the - 40-1243
rear RETRACT (auxil-
iary distributor) solenoid
valve solenoid is not con-
nected.
4 1601 U 44 - ECU detects that the rear - 40-1243
RETRACT (auxiliary dis-
tributor) solenoid valve
solenoid is shorting to
ground
3 1601 U 45 - ECU detects that the rear - 40-1243
RETRACT (auxiliary dis-
tributor) solenoid valve
solenoid is shorting to
battery positive
5 1602 U 46 - ECU detects that the rear - 40-1243
LOCK (auxiliary distribu-
tor) solenoid valve sole-
noid is not connected.
4 1602 U 47 - ECU detects that the rear - 40-1243
LOCK (auxiliary distribu-
tor) solenoid valve sole-
noid is shorting to ground
3 1602 U 48 - ECU detects that the rear - 40-1243
LOCK (auxiliary distribu-
tor) solenoid valve sole-
noid is shorting to battery
positive

20-86
Calibrations and electronic
diagnosis
Alarms - Services alarms list (AGROFARM 410 -> ZKDW470200TD30001)
Table 49
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
12 664 U 01 - I023/I024 - Ex- ECU detects a PTO - 40-723
ternal PTO con- speed sensor fault
trol
I075/I076 - Ex- 40-738
ternal PTO con-
trol
I090/I091 - Ex- 40-743
ternal PTO con-
trol
3 662 U 02 - I023/I024 - Ex- The ECU detects that the - 40-723
ternal PTO con- rear PTO control buttons
trol on the mudguards are
I075/I076 - Ex- continuously pressed 40-738
ternal PTO con-
trol
I090/I091 - Ex- 40-743
ternal PTO con-
trol
3 697 U 03 - I032 - Rear PTO ECU detects that the rear - 40-723
switch PTO control button is
I040 - Rear PTO shorting to ground. 40-728
switch
I083 - Rear PTO 40-738
switch
I097 - Rear PTO 40-743
switch
3 698 U 04 - I022 - Front ECU detects that the - 40-723
PTO switch front PTO control button
I039 - Front is shorting to ground. 40-728
PTO switch
I085 - Front 40-738
PTO switch
I099 - Front 40-743
PTO switch
5 550 U 06 - L008 - Rear ECU detects that the rear - 40-723
PTO control so- PTO solenoid valve sole- 40-728
lenoid valve noid is not connected 40-738
40-743
4 550 U 07 - L008 - Rear ECU detects that the - 40-723
PTO control so- rear PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
ground.
3 550 U 08 - L008 - Rear ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
battery positive.
5 551 U 09 - L001 - Front ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is not connected 40-738
40-743

20-87
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
4 551 U 10 - L001 - Front ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
ground.
3 551 U 11 - L001 - Front ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
battery positive.
5 653 U 12 - L001 - Front The ECU detects that the - 40-723
PTO control so- diff lock solenoid is not 40-728
lenoid valve connected 40-738
40-743
4 653 U 13 - L006 - Differen- The ECU detects that the - 40-1145
tial lock control differential lock solenoid 40-1166
solenoid valve is shorting to earth 40-1186
40-1206
3 653 U 14 - L006 - Differen- The control unit detects - 40-1151
tial lock control that the differential lock 40-1171
solenoid valve solenoid is shorting to 40-1192
40-1211
positive.
5 552 U 15 - L007 - 4WD The control unit detects - 40-1151
control solenoid that the 4WD engage- 40-1171
valve ment solenoid is not con- 40-1192
40-1211
nected
4 552 U 16 - L007 - 4WD The control unit detects - 40-1151
control solenoid that the 4WD solenoid is 40-1171
valve shorting to earth 40-1192
40-1211
3 552 U 17 - L007 - 4WD The control unit detects - 40-1151
control solenoid that the 4WD solenoid is 40-1171
valve shorting to battery posi- 40-1192
40-1211
tive
5 1,600 U 40 - ECU detects that the - 40-1237
rear EXTENDED (auxil- 40-1240
iary distributor) solenoid
valve solenoid is not con-
nected.
4 1,600 U 41 - ECU detects that the - 40-1237
rear EXTENDED (auxil- 40-1240
iary distributor) solenoid
valve solenoid is shorting
to ground
3 1,600 U 42 - ECU detects that the - 40-1237
rear EXTENDED (auxil- 40-1240
iary distributor) solenoid
valve solenoid is shorting
to battery positive
5 1601 U 43 - ECU detects that the - 40-1237
rear RETRACT (auxil- 40-1240
iary distributor) solenoid
valve solenoid is not con-
nected.

20-88
Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
4 1601 U 44 - ECU detects that the rear - 40-1237
RETRACT (auxiliary dis- 40-1240
tributor) solenoid valve
solenoid is shorting to
ground
3 1601 U 45 - ECU detects that the rear - 40-1237
RETRACT (auxiliary dis- 40-1240
tributor) solenoid valve
solenoid is shorting to
battery positive
5 1602 U 46 - ECU detects that the rear - 40-1237
LOCK (auxiliary distribu- 40-1240
tor) solenoid valve sole-
noid is not connected.
4 1602 U 47 - ECU detects that the rear - 40-1237
LOCK (auxiliary distribu- 40-1240
tor) solenoid valve sole-
noid is shorting to ground
3 1602 U 48 - ECU detects that the rear - 40-1237
LOCK (auxiliary distribu- 40-1240
tor) solenoid valve sole-
noid is shorting to battery
positive

Alarms - Services alarms list (AGROFARM 420 -> ZKDW510200TD30001)

Table 50
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
12 664 U 01 - I023/I024 - Ex- ECU detects a PTO - 40-723
ternal PTO con- speed sensor fault
trol
I075/I076 - Ex- 40-738
ternal PTO con-
trol
I090/I091 - Ex- 40-743
ternal PTO con-
trol
3 662 U 02 - I023/I024 - Ex- The ECU detects that the - 40-723
ternal PTO con- rear PTO control buttons
trol on the mudguards are
I075/I076 - Ex- continuously pressed 40-738
ternal PTO con-
trol
I090/I091 - Ex- 40-743
ternal PTO con-
trol

20-89
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
3 697 U 03 - I032 - Rear PTO ECU detects that the rear - 40-723
switch PTO control button is
I040 - Rear PTO shorting to ground. 40-728
switch
I083 - Rear PTO 40-738
switch
I097 - Rear PTO 40-743
switch
3 698 U 04 - I022 - Front ECU detects that the - 40-723
PTO switch front PTO control button
I039 - Front is shorting to ground. 40-728
PTO switch
I085 - Front 40-738
PTO switch
I099 - Front 40-743
PTO switch
5 550 U 06 - L008 - Rear ECU detects that the rear - 40-723
PTO control so- PTO solenoid valve sole- 40-728
lenoid valve noid is not connected 40-738
40-743
4 550 U 07 - L008 - Rear ECU detects that the - 40-723
PTO control so- rear PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
ground.
3 550 U 08 - L008 - Rear ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
battery positive.
5 551 U 09 - L001 - Front ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is not connected 40-738
40-743
4 551 U 10 - L001 - Front ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
ground.
3 551 U 11 - L001 - Front ECU detects that the - 40-723
PTO control so- front PTO solenoid valve 40-728
lenoid valve solenoid is shorting to 40-738
40-743
battery positive.
5 653 U 12 - L001 - Front The ECU detects that the - 40-723
PTO control so- diff lock solenoid is not 40-728
lenoid valve connected 40-738
40-743
4 653 U 13 - L006 - Differen- The ECU detects that the - 40-1145
tial lock control differential lock solenoid 40-1166
solenoid valve is shorting to earth 40-1186
40-1206
3 653 U 14 - L006 - Differen- The control unit detects - 40-1158
tial lock control that the differential lock 40-1178
solenoid valve solenoid is shorting to 40-1199
40-1218
positive.

20-90
Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
5 552 U 15 - L007 - 4WD The control unit detects - 40-1158
control solenoid that the 4WD engage- 40-1178
valve ment solenoid is not con- 40-1199
40-1218
nected
4 552 U 16 - L007 - 4WD The control unit detects - 40-1158
control solenoid that the 4WD solenoid is 40-1178
valve shorting to earth 40-1199
40-1218
3 552 U 17 - L007 - 4WD The control unit detects - 40-1158
control solenoid that the 4WD solenoid is 40-1178
valve shorting to battery posi- 40-1199
40-1218
tive
5 1,600 U 40 - ECU detects that the - 40-1237
rear EXTENDED (auxil- 40-1240
iary distributor) solenoid
valve solenoid is not con-
nected.
4 1,600 U 41 - ECU detects that the - 40-1237
rear EXTENDED (auxil- 40-1240
iary distributor) solenoid
valve solenoid is shorting
to ground
3 1,600 U 42 - ECU detects that the - 40-1237
rear EXTENDED (auxil- 40-1240
iary distributor) solenoid
valve solenoid is shorting
to battery positive
5 1601 U 43 - ECU detects that the - 40-1237
rear RETRACT (auxil- 40-1240
iary distributor) solenoid
valve solenoid is not con-
nected.
4 1601 U 44 - ECU detects that the rear - 40-1237
RETRACT (auxiliary dis- 40-1240
tributor) solenoid valve
solenoid is shorting to
ground
3 1601 U 45 - ECU detects that the rear - 40-1237
RETRACT (auxiliary dis- 40-1240
tributor) solenoid valve
solenoid is shorting to
battery positive
5 1602 U 46 - ECU detects that the rear - 40-1237
LOCK (auxiliary distribu- 40-1240
tor) solenoid valve sole-
noid is not connected.
4 1602 U 47 - ECU detects that the rear - 40-1237
LOCK (auxiliary distribu- 40-1240
tor) solenoid valve sole-
noid is shorting to ground

20-91
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
3 1602 U 48 - ECU detects that the rear - 40-1237
LOCK (auxiliary distribu- 40-1240
tor) solenoid valve sole-
noid is shorting to battery
positive
Alarms - Services alarms list (AGROFARM 430 -> ZKDW550200TD30001)
Table 51
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
12 664 U 01 - I049/I050 - Ex- ECU detects a PTO - 40-734
ternal PTO con- speed sensor fault
trol
3 662 U 02 - I049/I050 - Ex- The ECU detects that the - 40-734
ternal PTO con- rear PTO control buttons
trol on the mudguards are
continuously pressed
3 697 U 03 - I070 - Rear PTO ECU detects that the rear - 40-734
switch PTO control button is
shorting to ground.
3 698 U 04 - I071 - Front ECU detects that the - 40-734
PTO switch front PTO control button
is shorting to ground.
5 550 U 06 - L017 - Rear ECU detects that the rear - 40-734
PTO control so- PTO solenoid valve sole-
lenoid valve noid is not connected
4 550 U 07 - L017 - Rear ECU detects that the - 40-734
PTO control so- rear PTO solenoid valve
lenoid valve solenoid is shorting to
ground.
3 550 U 08 - L017 - Rear ECU detects that the - 40-734
PTO control so- front PTO solenoid valve
lenoid valve solenoid is shorting to
battery positive.
5 551 U 09 - L001 - Front ECU detects that the - 40-734
PTO control so- front PTO solenoid valve
lenoid valve solenoid is not connected
4 551 U 10 - L001 - Front ECU detects that the - 40-734
PTO control so- front PTO solenoid valve
lenoid valve solenoid is shorting to
ground.
3 551 U 11 - L001 - Front ECU detects that the - 40-734
PTO control so- front PTO solenoid valve
lenoid valve solenoid is shorting to
battery positive.

20-92
Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
5 653 U 12 - L001 - Front The ECU detects that the - 40-734
PTO control so- diff lock solenoid is not
lenoid valve connected
4 653 U 13 - L019 - Differen- The ECU detects that the - 40-1231
tial lock control differential lock solenoid
solenoid valve is shorting to earth
3 653 U 14 - L019 - Differen- The control unit detects - 40-1231
tial lock control that the differential lock
solenoid valve solenoid is shorting to
positive.
5 552 U 15 - L018 - 4WD The control unit detects - 40-1231
control solenoid that the 4WD engage-
valve ment solenoid is not con-
nected
4 552 U 16 - L018 - 4WD The control unit detects - 40-1231
control solenoid that the 4WD solenoid is
valve shorting to earth
3 552 U 17 - L018 - 4WD The control unit detects - 40-1231
control solenoid that the 4WD solenoid is
valve shorting to battery posi-
tive
5 1,600 U 40 - ECU detects that the - 40-1243
rear EXTENDED (auxil-
iary distributor) solenoid
valve solenoid is not con-
nected.
4 1,600 U 41 - ECU detects that the - 40-1243
rear EXTENDED (auxil-
iary distributor) solenoid
valve solenoid is shorting
to ground
3 1,600 U 42 - ECU detects that the - 40-1243
rear EXTENDED (auxil-
iary distributor) solenoid
valve solenoid is shorting
to battery positive
5 1601 U 43 - ECU detects that the - 40-1243
rear RETRACT (auxil-
iary distributor) solenoid
valve solenoid is not con-
nected.
4 1601 U 44 - ECU detects that the rear - 40-1243
RETRACT (auxiliary dis-
tributor) solenoid valve
solenoid is shorting to
ground
3 1601 U 45 - ECU detects that the rear - 40-1243
RETRACT (auxiliary dis-
tributor) solenoid valve
solenoid is shorting to
battery positive

20-93
 Calibrations and electronic
diagnosis
ART code In- Severity Component Fault Checks Link to sys-
fmi spn stru- tem
ment
panel
dis-
play
error
5 1602 U 46 - ECU detects that the rear - 40-1243
LOCK (auxiliary distribu-
tor) solenoid valve sole-
noid is not connected.
4 1602 U 47 - ECU detects that the rear - 40-1243
LOCK (auxiliary distribu-
tor) solenoid valve sole-
noid is shorting to ground
3 1602 U 48 - ECU detects that the rear - 40-1243
LOCK (auxiliary distribu-
tor) solenoid valve sole-
noid is shorting to battery
positive

20-94
30 - Method of intervention

30-1
 Method of intervention
30.1 - Tools for engine disassembly and reassembly
30.1.1 - Commercially available tools
Deutz 2012 2V UPS engines
Table 52
No. Figure Code, description & function Q.ty
1 Code 01899031 (8002) 1
Pressing pump: Check the seal of the cooling system.

© 35409-2

Fig. 190
2 Code 01899034 (8005) 1
Compression value test for diesel engines. (10 - 40 bar) Check of the
compression value.

© 35410-3

Fig. 191
3 Code 01899035 (8008) 1
Injector control equipment: With nebulised spray collection container.
Check the injectors.

© 35411-2

Fig. 192
4 Code 01899037 (8011) 1
Pliers for hose clips: Loosen and fix the hose clips. (e.g. fuel return line)

© 39426-1

Fig. 193
5 Code 01899038 (8012) 1
Box spanner insert: SW15, long.

© 35412-3

Fig. 194

30-2
Method of intervention
No. Figure Code, description & function Q.ty
6 Code 01899050 (8024) 1
Assembly pliers: Removal of the valve stem gaskets.

© 37509-2

Fig. 195
7 Code 01899054 (8035) 1
Box spanner insert: Reinforced, SW 22. Removal and refitting of the
main bearing.

© 37504-2

Fig. 196
8 Code 01899060 (8113) 1
Box spanner insert: Torx - E 14.

© 43022-0

Fig. 197
9 Code 01899061 (8114) 1
Box spanner insert: Torx - E 20.

© 35415-1

Fig. 198
10 Code 01899062 (8115) 1
V-belt tension tester from 150 to 600 N. Checking the V-belt tension.

© 35416-3

Fig. 199
11 Code 01899064 (8117) 1
Toothed box spanner insert: For rotating the injection pump.

© 46422-0

Fig. 200

30-3
 Method of intervention
No. Figure Code, description & function Q.ty
12 Code 01899092 (8189) 1
Torx tool set. Case content: • Double ring wrench E6/E8, • Double ring
wrench E10/E12, • Box spanner inserts E8 and E10 (1/4 inch), • Box
spanner inserts E10 and E12 (3/8 inch), • Box spanner inserts E18 (1/2
inch).

© 39432-1

Fig. 201
13 Code 01899093 (8190) 1
Rotation angle gauge with magnet. Adjustment of valve clearance.

© 43528-0

Fig. 202
14 Code 01899094 (8191) 1
Screwdriver insert for slot head screw. Valve clearance adjustment.

© 43060-0

Fig. 203
15 Code 01899095 (8192) 1
Bowlen wrench: Fuel prefilter (Racor).

© 43193-1

Fig. 204
16 Code 01899096 (8193) 1
Screwdriver insert with hexagonal pin pressure inserted (5 mm), 1/2
inch, long version (in combination with the rotation angle gauge 8190)

© 43183-0

Fig. 205
17 Code 01899097 (8194) 1
Screwdriver insert with hexagonal pin pressure inserted (4 mm), 3/8
inch, long version (in combination with the rotation angle gauge 8190
and 1/2 to 3/8 inch reducer)

© 43183-0

Fig. 206

30-4
Method of intervention
No. Figure Code, description & function Q.ty
18 Code 01899099 (8196) 1
Open-ended wrench: SW 13, for the torque wrench. Tighten the check
nuts of the valve clearance adjustment screw.

© 43019-0

Fig. 207
19 Code (...) 8198 1
Bradawl: Disassembly of the shaft seal ring.

© 43206-0

Fig. 208
20 Code 01899100 (8199) 1
Crow’s foot wrench: SW 15. 3/4 inch (in combination with the rotation
angle gauge 8190)

© 44309-0

Fig. 209
21 Code 01899110 (9017) 1
Assembly lever. (e.g. valve assembly and disassembly)

© 37511-2

Fig. 210
22 Code 01899112 (9090) 1
Circlip pliers: 320 mm. Tension the circlip.

© 00000-0

Fig. 211

30-5
 Method of intervention
30.2 - Workshop tools for engine disassembly and reassembly
30.2.1 - Workshop tools for engine disassembly and reassembly
Deutz 2012 2V UPS engines
Table 53
No. Figure Code, description & function Q.ty
1 Code 02992019 (100190) 1
Dummy injector: In combination with the compression value tester code
01899034 (8005)

© 42524-1

Fig. 212
2 Code ... (100320) 1
Rotation device. On the flywheel side.

Fig. 213
3 Code ... (100330) 1
Rotation device: V-belt pulley. Turn the crankshaft on the torsional vibra-
tion damper.

© 35423-1

Fig. 214
4 Code 01899126 (100400) 1
Dial gauge with stop wheel. Measurement interval: 0 - 10 mm / 0.01 mm.

© 35424-1

Fig. 215
5 Code 01899127 (100410) 1
Digital dial gauge. Measurement interval: 0 - 30 mm / 0.01 mm.

© 43205-0

Fig. 216

30-6
Method of intervention
No. Figure Code, description & function Q.ty
6 Code 02992041 (100750) 1
Measurement device: Sliding vernier scale with two spacer discs. In com-
bination with code 01899126 (100400) and code 01899127 (100410).
Valve retraction check. Piston protrusion check.

© 39402-2

Fig. 217
7 Code 02992045 (100800) 1
Regulation device. For measuring the stroke and blocking the adjust-
ment rod.

© 46441-0

Fig. 218
8 Code 02992046 (100810) 1
Centring pin. For mass compensation shafts.

© 46439-0

Fig. 219
9 Code 02992047 (100830) 1
Pressure device for the adjustment rod.

© 46443-0

Fig. 220
10 Code 01899131 (103050) 1
Box spanner insert SW 15, 3/4 inch. In combination with the rotation
angle gauge code 01899093 (8190).

© 43023-0

Fig. 221
11 Code 02992079 (103210) 1
Measurement device for measuring the base circle. (in engines with an
injection advance variator)

© 46444-0

Fig. 222

30-7
 Method of intervention
No. Figure Code, description & function Q.ty
12 Code ... (103220) 1
Special pliers for extracting the roller tappet. Measurement device com-
ponent, code 02992079 (103210)

© 43175-0

Fig. 223
13 Code 02992084 (110030) 1
Extractor for disassembly of the injection valve. In combination with the
slide hammer extractor code 02992294 (150800).

© 35433-2

Fig. 224
14 Code 02992089 (110110) 1
SW11 support for tightening the injection valve in the screw clamp.

© 35434-2

Fig. 225
15 Code 02992112 (110500) 1
Special wrench SW 17 for disassembly and assembly of the high pres-
sure lines.

© 35436-1

Fig. 226
16 Code 01899132 (110700) 1
Long box spanner insert for the assembly and disassembly of pressure
sensors. (Rail pressure, oil pressure, fuel pressure)

© 43198-2

Fig. 227
17 Code 02992127 (110901) 1
Tool for the disassembly and assembly of the O-rings. Assembly kit com-
ponent, code 02992126 (110900)

© 45950-1

Fig. 228

30-8
Method of intervention
No. Figure Code, description & function Q.ty
18 Code ... (120430) 1
Spark plug assembly and disassembly tool.

© 40333-1

Fig. 229
19 Code 02992136 (120660) 1
Extraction device. Disassembly of the injection valve. In combination
with the slide hammer extractor code 02992294 (150800)

© 45111-0

Fig. 230
20 Code 02992139 (120900) 1
Adjustable support stand. Tightening the cylinder head.

© 35438-3

Fig. 231
21 Code 02992140 (120910) 1
Base plate. In combination with support stand code 02992139 (120900),
if the support stand is not screwed on fixed.

© 35439-3

Fig. 232
22 Code 02992145 (121410) 1
Valve stem gasket assembly tool.

© 37614-2

Fig. 233
23 Code ... (121420) 1
Assembly bushes. Set of assembly bushes for the valve stem gasket.

© 43210-0

Fig. 234

30-9
 Method of intervention
No. Figure Code, description & function Q.ty
24 Code 02992155 (130300) 1
Universal pliers for piston rings. Disassembly and assembly of piston
rings.

© 43021-0

Fig. 235
25 Code 02992165 (130440) 1
Trapezoidal groove wear gauge. Piston diameter 101 mm. Check piston
ring groove.

© 36461-2

Fig. 236
26 Code 02992181 (130670) 1
Piston ring compression collar for piston assembly: Piston Ø mm. 101.

© 39408-1

Fig. 237
27 Code 02992187 (131200) 1
Base plate for press-fit and removal of the connecting rod small end
bush. In combination with assembly tool set code 02992188 (131210)

© 37616-1

Fig. 238
28 Code 02992189 (131220) 1
Set of assembly tools for press-fit and removal of the connecting rod
small end bush. In combination with the base plate code 02992187
(131200)

© 37617-1

Fig. 239
29 Code 02992213 (142670) 1
Assembly device for the crankshaft O-ring. (opposite end to flywheel)

© 35445-1

Fig. 240

30-10
Method of intervention
No. Figure Code, description & function Q.ty
30 Code 02992223 (142830) 1
Assembly device for the crankshaft O-ring. (flywheel side)

© 35446-1

Fig. 241
31 Code 02992251 (143840) 1
Camshaft bearings assembly and disassembly tool.

© 46440-0

Fig. 242
32 Code 02992275 (144800) 1
Counterhead for the torsional vibration damper.

© 35453-1

Fig. 243
33 Code 02992294 (150800) 1
Slide hammer extractor for the disassembly of the injection valve.

© 35449-2

Fig. 244
34 Code 02992301 (151500) 1
Tool for truncation. For removal of the lubricant oil sump pan in plate from
the crankcase.

© 45974-0

Fig. 245
35 Code 01899142 (170050) 1
Special wrench for the removal of the filter cartridges.

© 37629-2

Fig. 246

30-11
 Method of intervention
No. Figure Code, description & function Q.ty
36 Code ... (170160) 1
Plugs and caps: 1 set of different sized plugs and caps. For closing the
holes in the fuel distribution system.

© 43663-0

Fig. 247
37 Code 01899000 (6066) 1
Assembly stand for tightening the engine on two sides.

© 35451-2

Fig. 248
38 Code ... (6066/158) 1
Clamping support, consisting of: 1 support code 01899010 (6066/158-1)
rear right; 1 support 01899011 (6066/158-2) rear left; 1 support 01899012
(6066/158-3) front right; 1 support 01899013 (6066/158-4) front left. In
combination with the assembly stand code 01899000 (6066). Tightening
the engine on two sides.

© 35452-1

Fig. 249
39 Code 01899028 (6068) 1
Suspension device: Maximum load ( 2 tonnes), 3-point suspension,
screw tensioners, crosspiece, chain and hooks.

© 43184-0

Fig. 250

30-12
Method of intervention
30.3 - B0 - Engine
30.3.1 - Air conditioning compressor drive belt
REMOVAL
1. DANGER
Disconnect the lead from the battery negative terminal (-) and apply the parking brake.

2. Loosen nut (1) and unscrew tie rod (2) to slacken off drive belt (3).

Fig. 251
3. For versions with front PTO
Using a pin punch, remove pin (4) and withdraw PTO engagement shaft (5)
towards the front of the tractor.

Fig. 252
4. For all versions
Remove drive belt (3).
Installation
Install by following the removal steps in reverse order and carry out the following procedures:
Procedure 2
l Adjust the tension of the fan drive belt.

30.3.2 - Tension adjustment of the fan and air conditioning compressor drive belt
Tension adjustment
1. m Before adjusting the tension, carefully examine the drive belt for signs of wear. The belt must be renewed immediately
at the first sign of cracking, fraying or separation of the plies.
m Always replace both drivebelts at the same time.
DANGER
If new drivebelts are fitted, re-adjust the tension after approx. 50 operating hours.

30-13
 Method of intervention
2. Loosen nuts (1) and screws (2).

Fig. 253
3. Tighten tie-rod (3) forcing it gradually until obtaining belt deflection of 10-15
mm (0.4-0.6 in.) when applying a load of 10 kg (22 lb.) on the long section
of the belt.
mIn the case of a new belt, deflection should be 7-9 mm (0.276 - 0.355
in.).
Secure compressor (4) in place and re-check belt tension.

Fig. 254

30.3.3 - Alternator, fuel pump and water pump drive belt

REMOVAL
1. DANGER
Disconnect the lead from the battery negative terminal (-) and apply the parking brake.

2. Loosen screws (1) and (2) securing the fuel pump, disengage alternator
drive belt (3) and remove it by passing it between the bottom of the crank-
shaft pulley and the front axle support.

Fig. 255

Installation
Install by following the removal steps in reverse order and carry out the following procedures:
Procedure 2
l Adjust drive belt tension.

30-14
Method of intervention
30.3.4 - Tension adjustment of the alternator, fuel pump and water pump drive belt
Tension adjustment
1. Tension the belt using a “T” bar with a 3/4” drive extension, or a 3/4” angle
drive bar inserted in the aperture in the support of fuel pump (1).
Tension the drive belt by turning the bar clockwise and then tighten down
screws (2) and (3).

Fig. 256
2. To check that the tension is correct, use the tool and procedure indicated
in the engine manual.
Static deflection “A” on first fitting
m 13 mm belt: 450±50 N
Static deflection “A” after 15 minutes
m 13 mm belt: 300±50 N
DANGER
This check should be carried out with the engine cold.
Fig. 257

30.3.5 - Compression test

Commercially available tools:
l Compression value test: 8005
l Torx tool set: 8189
Special tools:
l Pipe union: 100130
Compression test
1. m Adjust valve clearance.
See para. 30.3.7 - Adjustment of valve cl... - page 30-22
m Disassemble the injection valves.
See para. 30.3.50 - Fitting and removing i... - page 30-188
m Fit seal (1)
m Fit union (2).
2

© 46377-1

Fig. 258

30-15
 Method of intervention

30-16
Method of intervention
5. Note
The pressure reading will depend on the number of starter No.
Kompression in bar
revolutions during the testing process and on the altitude at Compression value in bar
Pression en bar
which the test is performed. The limit values therefore can- Dat. _________
10 15 20 25 30 35 40
not be defined with precision. We recommend that the read-

Zyl.
ings obtained are used solely for comparison between the 1
different cylinders. A difference between cylinders of over 2
3
15% should be investigated by dismantling the cylinder giv- 4
5
ing the low reading. 6
7
8
DBGM Made in German y
MOTOMETER
© 33771-5

Fig. 262
6. m Remove the compression tester and adapter (1).

© 46308-1

Fig. 263
7. m Remove screw (1).
m Remove retaining bracket (2).
m Remove the union.
m Remove the seal.
m Assemble the injection valves.
See para. 30.3.50 - Fitting and removing i... - page 30-188

© 46378-1

Fig. 264

30-17
 Method of intervention
30.3.6 - Assembly and disassembly of the engine on the assembly stand
Commercially available tools:
l Lifting device
l Loading rope
Special tools:
l Assembly stand with adapter plates: 6066
l Clamping support: 6066/158
l Suspension device: 6068
NOTE
The repair process shown does not take specific customer equipment into account; components not included in the
standard equipment are not shown.

Assembly of the engine on the stand

1. m Hook the suspension device with the support chain to the transport
slats (arrows).
n 4-cylinder: 410 kg

m Hang the engine from the workshop crane.

NOTE
Disassemble all the feet.

m Fit the engine on the assembly stand.

© 46446-0

Fig. 265
2. m Fit the clamping support 6066/158-1 (1) on the support.
m Tighten the screws (2) and the check nuts: 70 Nm.
m Tighten the screws (3) and the check nuts: 90 Nm.

3 2

© 46448-0

Fig. 266

30-18
Method of intervention
3. m Fit the clamping support 6066/158-2 (1) on the support.
m Tighten the screws (2) and the check nuts: 70 Nm.
m Tighten the screws (3) and the check nuts: 90 Nm.
1
2

© 46449-0

Fig. 267
4. m Fit the clamping support 6066/158-3 (1) on the crankcase.
m Tighten the screw (2): 70 Nm.
m Tighten the screws (3) and the check nuts: 90 Nm.
2

3
1

© 46447-0

Fig. 268
5. m Fit the clamping support 6066/158-4 (1) on the crankcase.
m Tighten the screws (2): 70 Nm.
m Tighten the screws (3) and the check nuts: 90 Nm.

3
© 46450-0

Fig. 269

30-19
 Method of intervention
6. m Align the engine on the assembly stand.
m Tighten all the screws (1).
m Hang the engine from the workshop crane.

1
© 46459-0

Fig. 270

Disassembly of the engine from the assembly stand

1. m Hook the suspension device with the support chain to the transport
slats (arrows).
n 4-cylinder: 410 kg

m Hang the engine from the workshop crane.

© 46446-0

Fig. 271
2. m Unscrew the check nuts.
m Remove the screws (3) and the check nuts.
m Remove screws (2).
m Withdraw the clamping support (1).
2

3
© 46450-0

Fig. 272

30-20
Method of intervention
3. m Unscrew the check nuts.
m Remove the screws (3) and the check nuts.
m Withdraw the clamping support (1).
1
3

© 46449-1

Fig. 273
4. m Unscrew the check nuts.
m Remove the screws (3) and the check nuts.
m Withdraw the clamping support (1).

3 3

© 46448-1

Fig. 274
5. m Unscrew the check nuts.
m Unscrew screw (2)
m Remove the screws (3) and the check nuts.
m Remove the clamping support (1). 2
NOTE
Fit all the feet.
3
1
m Deposit the engine.
m Hang the engine from the workshop crane.
3

© 46447-0

Fig. 275

30-21
 Method of intervention
30.3.7 - Adjustment of valve clearance
Commercially available tools:
l Rotation angle gauge: 8190
l Open-ended wrench SW13: 8196
l Screwdriver insert for slot head screws: 8191
l Screwdriver insert for hexagonal pins (5 mm): 8193
Special tools:
l Rotation device: 100320
NOTE
Leave the engine to cool for at least 30 minutes before adjusting valve clearance, .
Engine oil temperature < 80°C.

Bring the engine to valve overlap position

1. m Fit the rotation device.
See para. 30.3.39 - Removal and refitting ... - page 30-144
m Remove the cylinder head cover.
See para. 30.3.10 - Disassembly and assemb... - page 30-32
m Turn the crankshaft with the rotation tool into the valve overlap posi-
tion for cylinder 1.

© 46461-0

Fig. 276
2. Positions of the intake and exhaust valves:
IN = intake valve. EX = exhaust valve
EX IN

© 46381-0

Fig. 277

30-22
Method of intervention
3. 4 cylinders. Firing order:
1–3–4–2

Table 54

Valves Cylinders
at overlap 1 3 4 2
angle
set 4 2 1 3

Valve overlap means that: © 46380-0

Fig. 278
the intake valve starts to open and the exhaust valve starts
to close.

Adjustment of the intake valve clearance

1. m Loosen locknut (1).
m Turn adjustment screw (2) to take up the clearance.
NOTE 2
The rocker arm should rest on the thrust washer of
the collet (arrowed) with no clearance.

WARNING 1
Pay attention to the version of the adjustment screws (slot,
hexagon, internal hexagon).

© 46382-0

Fig. 279
2. m Position rotation angle disc with screwdriver insert on adjuster screw.
m Fix the magnet of the rotation angle gauge to the cylinder head.
m Turn the rotation angle gauge in the direction of the arrow to “0”.
NOTE
Do not move the adjustment screw.

© 46462-0

Fig. 280

30-23
 Method of intervention
3. m Turn the adjustment screw in the direction of the arrow.
n Intake: 75°.

© 46463-0

Fig. 281
4. m Hold the adjustment screw in this position.
m Tighten the check nut (1) using the open-ended wrench: 20 Nm.
m Remove the rotation angle gauge.

© 46464-0

Fig. 282

Adjustment of the exhaust valve clearance

1. m Loosen locknut (1).
m Turn adjustment screw (2) to take up the clearance.
NOTE
The rocker arm should rest on the thrust washer of
the collet (arrowed) with no clearance.
2

© 46387-0

Fig. 283

30-24
Method of intervention
2. m Locate the rotation angle gauge with the slot head screwdriver insert
on the adjustment screw.
m Fix the magnet of the rotation angle gauge to the cylinder head.
m Turn the rotation angle gauge in the direction of the arrow to “0”.
NOTE
Do not move the adjustment screw.

© 46465-0

Fig. 284
3. m Turn the adjustment screw in the direction of the arrow.
n Exhaust: 120°.

© 46466-0

Fig. 285
4. m Hold the adjustment screw in this position.
m Tighten the check nut (1) using the open-ended wrench: 20 Nm.
m Remove the rotation angle gauge.
m Fit the cylinder head cover.
See para. 30.3.10 - Disassembly and assemb... - page 30-32
m Remove the rotation device.
See para. 30.3.39 - Removal and refitting ... - page 30-144

© 46467-0

Fig. 286

30-25
 Method of intervention
30.3.8 - Removal and refitting of the rocker arms and pedestals
Commercially available tools:
l Box spanner insert Torx E14: 8113
l Rotation angle gauge: 8190
Removal of the rocker arms and pedestals
1. m Remove the cylinder head cover.
See para. 30.3.10 - Disassembly and assemb... - page 30-32
m Undo the cylindrical head screw (1) using the socket wrench insert.
m Unscrew screw (2)
m Remove the rocker mount. 2
NOTE
Put the components to one side in the order in which
they were removed.

© 46451-2

Fig. 287
2. m Withdraw pushrods (1).
NOTE
Put the components to one side in the order in which
they were removed.

© 46452-0

Fig. 288
3. m Carry out a visual inspection of the components.

© 46453-0

Fig. 289

30-26
Method of intervention
Refitting the rocker arms and pedestals
1. m Insert pushrods (1).
NOTE
Take care to insert the pushrods in their original posi-
tions. The ball ends of the pushrods must locate in
the cups of the tappets.

© 46452-0

Fig. 290
2. m Fit rocker pedestal (1).
NOTE
The ball heads (2) must be in the pivots of the push-
1
rods.

© 46454-0

Fig. 291
3. m Screw in the screw (1).
NOTE
Do not tighten the screw at this stage.
1

© 46455-0

Fig. 292

30-27
 Method of intervention
4. WARNING
In the case of written certification, the cylindrical head
screws can be used a maximum of 3 times, otherwise re- 1
place them each time they are removed.
m Lightly oil the cylindrical head screw (1).
m Screw the cylindrical head screw (1).

© 46456-0

Fig. 293
5. m Orient the rocker pedestals symmetrically about the axes of the
valves
m Tighten the cylindrical head screws using the box spanner insert.
n Pretightening value: 30 Nm.

WARNING
Before tightening the screw, check that the pushrods are not
under load due to valve overlap.

© 46457-0

Fig. 294
6. m Tighten (1) the screw: 21 Nm.

© 46451-1

Fig. 295

30-28
Method of intervention
7. m Tighten the cylindrical head screws using the box spanner insert.
n Retightening value: + 80 Nm + 90°.

m Adjust valve clearance.

See para. 30.3.7 - Adjustment of valve cl... - page 30-22

© 46457-0

Fig. 296

30.3.9 - Disassemble and complete the rocker and support, check

Commercially available tools:
l Internal bore meter
l Palmer
l Circlip pliers
Special tools:
l Dial gauge: 100400
Disassembly of the rocker support
1. m Disassemble the rocker and the support.
See para. 30.3.8 - Removal and refitting ... - page 30-26
m Remove the circlip with the specific plier.

© 46389-0

Fig. 297
2. m Remove the rocker.
NOTE
Put the components to one side in the order in which
they were removed.

© 46390-0

Fig. 298

30-29
 Method of intervention
Rocker check
1. m Measure the rocker hole.
n Exhaust: 21.02 (+0.033,- 0) mm.

n Intake: 21.02 (+0.033,- 0) mm.

NOTE
The rocker wear limit was reached, replace it.

© 39032-1

Fig. 299
2. m Unscrew the check nut (1).
m Unscrew the adjustment screw (2).
WARNING
Pay attention to the version of the adjustment screws (slot,
hexagon, internal hexagon).

NOTE 2

Put the components to one side in the order in which they

were removed.

1
© 46393-0

Fig. 300
3. m Visually check the wear of the components.
m Check that the oil channels (arrow) are completely free.

© 46392-0

Fig. 301

30-30
Method of intervention
4. m Tighten the adjustment screws (1).
m Tighten the check nuts (2). 2

© 46468-0

Fig. 302

Check the rocker pins

1. m Measure the diameter of the main journals with the palmer: 21 (+0,-
0.052) mm.
NOTE
The rocker support wear limit was reached, replace
it.

© 46469-0

Fig. 303

Completion of the rocker support

1. m Lightly oil the rocker pins.
m Push the rockers (1) on the pins.
2
m Push the rockers (2) on the pins.
NOTE
1
The rocker must be turned with the contact surface
facing (3) facing towards the threaded hole (arrow).
Fit the rockers (1) on the exhaust side. Fit the rockers
(2) on the intake side.

3
© 46471-0

Fig. 304

30-31
 Method of intervention
2. m Fit the new circlips (1).
m Assemble the rockers and support.
See para. 30.3.8 - Removal and refitting ... - page 30-26

© 46453-1

Fig. 305

30.3.10 - Disassembly and assembly of the cylinder head

Commercially available tools:
l Box spanner insert Torx E14: 8113
Removal of the cylinder head cover
1. m Remove all the screws (1).
m Remove cylinder head cover (2).
2

© 46471-1

Fig. 306
2. m Cut the gasket at the ribs (1).
m Remove the gasket.
m Carry out a visual inspection of the components.

© 46587-0

Fig. 307

30-32
Method of intervention
3. m Disassemble the fan support.
See para. 30.3.63 - Removal and refitting ... - page 30-230
m Disassemble the exhaust pipe.
See para. 30.4.3 - Removal and refitting ... - page 30-239

© 46590-0

Fig. 308
4. m Disassemble the injection valves.
See para. 30.3.50 - Fitting and removing i... - page 30-188
m Disassemble the rocker support.
See para. 30.3.8 - Removal and refitting ... - page 30-26
m Disassemble the turbocharging air duct.
See para. 30.3.44 - Removal and refitting ... - page 30-159
m Remove screws (1).
2
m Remove support (2).

© 46331-0

Fig. 309
5. m Unscrew all the screws (1) using the long reach socket.
m Remove the cylinder head. 1
m Remove the gasket.
m Clean the mating surfaces.

© 46334-0

Fig. 310

30-33
 Method of intervention
Assembly of the cylinder head
1. NOTE
Measure the protrusion of all pistons. Select the cylinder
head seal based on the greatest measured piston protru-
sion.
m Measure the piston protrusion.
See para. 30.3.12 - Measuring piston protr... - page 30-42

© 42565-0

Fig. 311
2. m Select the cylinder head seal based on the greatest measured pis-
ton protrusion.
Table 55

Piston protrusion Hole

0.33 - 0.55 mm 1
0.56 - 0.65 mm 2
0.66 - 0.76 mm 3

Example:
piston protrusion = 0.7 mm corresponds to a cylinder head
seal with 3 holes (arrow). © 44154-0

Fig. 312
3. NOTE
Check that tightening bush (1) is present.

© 46335-0

Fig. 313

30-34
Method of intervention

30-35
 Method of intervention
7. m Fit rocker pedestal (1).
NOTE
The ball heads (2) must be in the pivots of the push-
1
rods.

© 46454-0

Fig. 317
8. m Screw in the screw (1).
NOTE
Do not tighten the screw at this stage.
1

© 46455-0

Fig. 318
9. WARNING
In the case of written certification, the cylindrical head
screws can be used a maximum of 3 times, otherwise re- 1
place them each time they are removed.
m Lightly oil the cylindrical head screw (1).
m Screw the cylindrical head screw (1).

© 46456-0

Fig. 319

30-36
Method of intervention
10. m Orient the rocker pedestals symmetrically about the axes of the
valves
m Tighten the cylindrical head screws with the socket wrench insert.
30 Nm.
WARNING
Before tightening the screw, check that the pushrods are not
under load due to valve overlap.

© 46457-0

Fig. 320
11. m Tighten (1) the screw: 21 Nm.

© 46451-1

Fig. 321
12. m Tighten all the cylindrical head screws according to the tightening
sequence.
n Retightening value: 30 Nm + 80 Nm + 90°.

NOTE
14 6 4 12
Use the box spanner insert.
18 10 2 8 16

17 9 1 7 15
13 5 3 11

© 45131-0

Fig. 322

30-37
 Method of intervention
13. m Fit support (2).
m Tighten (1) the screws.
m Assemble the turbocharging air duct.
See para. 30.3.44 - Removal and refitting ... - page 30-159
m Assemble the rocker support.
See para. 30.3.8 - Removal and refitting ... - page 30-26
m Adjust valve clearance.
2
See para. 30.3.7 - Adjustment of valve cl... - page 30-22
m Assemble the injection valves.
See para. 30.3.50 - Fitting and removing i... - page 30-188 1

© 46331-0

Fig. 323
14. m Assemble the exhaust pipe.
See para. 30.4.3 - Removal and refitting ... - page 30-239
m Assemble the fan support.
See para. 30.3.63 - Removal and refitting ... - page 30-230

© 46590-0

Fig. 324

Refitting the cylinder head cover

1. m Cut the new gasket at the ribs (1).
WARNING
Do not bend the flat gasket with metal ribbing. Sand the cut
areas.

© 46587-0

Fig. 325

30-38
Method of intervention
2. m Clean the mating surfaces.
m Fit a new gasket.
NOTE
Check the installation position is correct.

m Fit the cylinder head cover.

m Tighten all screws (1) alternately: 11 Nm.

© 46474-2

Fig. 326
3. NOTE
Make sure the assembly position is correct (arrow).

© 46473-2

Fig. 327

30.3.11 - Grinding the cylinder head seal surface

Commercially available tools:
l Flattener
l Roughness gauge
l Depth gauge
NOTE
When the flattener is used, following the specific instructions of the manufacturer.

Preparation of the cylinder head

1. m Disassemble the valves.
See para. 30.3.13 - Valve assembly and dis... - page 30-45
m Deburr the top of the cylinder head.
NOTE
To ensure a correct fit, the cylinder head surface
must be free of burr or gasket residue.

© 36627-1

Fig. 328

30-39
 Method of intervention
Flattening the cylinder head
1. m Tighten the cylinder head on the flattener.
m Align the cylinder head.
m Flattener tool for aligning the cylinder head.

© 39731-1

Fig. 329
2. m Flattening the sealing surface of the cylinder head.
NOTE
The lapping procedure must be repeated if the seal
surface of the cylinder head is not perfectly flat (rec-
ognisable by variations in colour in the ground sur-
face). The tool supply dimension is maximum 0.2 mm
for the flattening process.

© 39730-1

Fig. 330

Check of the sealing surface of the cylinder head

1. m Visual inspection of the sealing surface of the cylinder head.
m Visually inspect the surface of the combustion chamber.
m Fit the cylinder head gasket.
m Mark the surface of the combustion chamber (arrow).
NOTE
Do not mark with a pointed implement as this may
damage to the cylinder head seal surface.

© 36645-1

Fig. 331

30-40
Method of intervention
2. m Remove the cylinder head seal.
m Visual inspection of the sealing surface of the cylinder head.
NOTE
Minor damage to the combustion chamber surface
is permitted (as indicated by arrow). The lapping
procedure for the cylinder head must be repeated,
however, even if minor damage to the cylinder head
surface is visible. The cylinder head wear limit was
reached, replace it.

© 39732-1

Fig. 332
3. m Measure the roughness of the cylinder head seal surface with the
roughness gauge: Rz 25.
NOTE
If the value measured is not within the permissible
range, the cylinder head seal surface must be lapped
again using different settings for the lapping machine.

© 36647-1

Fig. 333
4. m Measure the height of the cylinder head with a depth gauge.
n Standard: 90 mm.

n Undersizing value: 89.4 mm.

NOTE
The cylinder head wear limit was reached, replace it.

© 36646-1

Fig. 334

30-41
 Method of intervention
5. m Remove the cylinder head from the flattener.
m Apply the repair date and factory mark on the cylinder head.
WARNING
Do not apply the label to a sealing surface.

NOTE
Mark the cylinder head after each repair.

m Assemble the valves.

See para. 30.3.13 - Valve assembly and dis... - page 30-45 © 39731-1

Fig. 335

30.3.12 - Measuring piston protrusion

Special tools:
l Rotation device: 100330
l Dial gauge: 100400
l Measurement device: 100750
Measuring piston protrusion
1. m Fit the rotation device.
See para. 30.3.39 - Removal and refitting ... - page 30-144
m Disassemble the cylinder head.
See para. 30.3.10 - Disassembly and assemb... - page 30-32

© 46474-0

Fig. 336
2. m Turn the crankshaft until the respective piston is positioned just be-
fore the top dead centre (arrow).

© 46333-0

Fig. 337

30-42
Method of intervention

30-43
 Method of intervention
6. m Move the sliding vernier scale.
m Position the preloaded probe on the required measurement points.
m Continue to uniformly rotate the crankshaft until the return point of
the dial gauge pointer is reached.
NOTE
Do not place the dial gauge probe on the markings
on the piston. Note the maximum value measured.

© 43514-1

Fig. 341
7. m Select the cylinder head seal based on the greatest measured pis-
ton protrusion.
Table 56

Piston protrusion Hole

0.33 - 0.55 mm 1
0.56 - 0.65 mm 2
0.66 - 0.76 mm 3

NOTE
Example: piston protrusion = 0.7 mm corresponds to a cylin-
der head seal with 3 holes (arrow). © 44154-0

Fig. 342
8. m Assemble the cylinder head.
See para. 30.3.10 - Disassembly and assemb... - page 30-32
m Remove the rotation device.
See para. 30.3.39 - Removal and refitting ... - page 30-144

© 46474-0

Fig. 343

30-44
Method of intervention
30.3.13 - Valve assembly and disassembly
Commercially available tools:
l Sliding gauge
l Assembly pliers: 8024
l Assembly lever: 9017
Special tools:
l Support stand: 120900
l base plate: 120910
l Assembly tool: 121410
l Assembly bushes: 121420
Valve disassembly
1. m Disassemble the cylinder head.
See para. 30.3.10 - Disassembly and assemb... - page 30-32
m Assemble the support stand (1) on the base plate (2).
m Assemble the cylinder head on the support stand. 1

2
© 42583-0

Fig. 344
2. m Remove the circlip (1).
DANGER
Risk of injury! The circlip jumps away.

© 42584-0

Fig. 345
3. m Remove the thrust washer (1).

© 42585-0

Fig. 346

30-45
 Method of intervention

30-46
Method of intervention
7. m Assemble the valves.
m Measure the length of the valve spring with a vernier scale: 59 mm.
NOTE
If the valve spring wear limit was reached, replace it.

© 35856-2

Fig. 350
8. m Lightly oil the valve stem.
m Insert and retain the valve.
m Push the assembly bush (1) through the valve key seats.

© 42589-0

Fig. 351
9. m Push a new valve stem gasket (1) on the assembly bush.
m Remove the assembly bush.

© 42590-1

Fig. 352

30-47
 Method of intervention
10. m Push the valve stem gasket with the assembly tool (1) to the stop.

© 42591-0

Fig. 353
11. m Insert the valve spring (1).
m Insert the collet (2).
2

© 42592-0

Fig. 354
12. m Apply the assembly lever.
m Fit the assembly lever on the valve collet.
m Push the valve spring downwards with the assembly lever and insert
two retaining tapered rings (1).
NOTE
Make sure the position of the retaining tapered rings
in the valve key seats is correct.

© 42593-0

Fig. 355

30-48
Method of intervention
13. m Disassemble the assembly lever.
m Insert the thrust washer (1).

© 42585-0

Fig. 356
14. m Insert the circlip (1).
NOTE
Make sure that the circlip is inserted correctly in the
1
groove.

© 42594-0

Fig. 357
15. m Disassemble the cylinder head from the support stand (1).
m Disassemble the base plate support stand (2).
m Assemble the cylinder head.
See para. 30.3.10 - Disassembly and assemb... - page 30-32 1

2
© 42583-0

Fig. 358

30-49
 Method of intervention
30.3.14 - Valve check
Commercially available tools:
l Palmer
l Sliding gauge
NOTE
Clean all the valves. If the valve wear limit was reached, replace it.

Check the diameter of the valve stem

1. m Disassemble the valves.
See para. 30.3.13 - Valve assembly and dis... - page 30-45
m Use the palmer to measure the diameter of the valve stem.
n Intake valve: 7.98 (+0, -0.015) mm
n Exhaust valve: 7.96 (+0, -0.015) mm

© 42182-1

Fig. 359

Check the thickness of the valve edge

1. m Use the sliding gauge to measure the thickness of the valve edge.
n Intake valve: 2.3 mm
n Exhaust valve: 1.61 mm

© 42183-1

Fig. 360

30-50
Method of intervention
Check the diameter of the valve head
1. m Use the sliding gauge to measure the diameter of the valve head.
n Intake valve: 41.7 (+0.1, -0.1) mm
n Exhaust valve: 35.9 (+0.1, -0.1) mm

m Assemble the valves.

See para. 30.3.13 - Valve assembly and dis... - page 30-45

© 42184-1

Fig. 361

30.3.15 - Check the valve guide

Commercially available tools:
l Magnetic stand for measurements
Special tools:
l Dial gauge: 100400
NOTE
New valves are used for the check. The valve guide wear limit was reached, replace it.

Check the valve guide

1. m Disassemble the valves.
See para. 30.3.13 - Valve assembly and dis... - page 30-45
m Visually check the wear of the valve guide.
m Apply the magnetic stand for measurements.
m Insert the dial gauge.
m Insert a new valve.
m Apply the preloaded probe on the valve stem (arrow).
m Adjust the dial gauge to “0”.

© 42595-0

Fig. 362

30-51
 Method of intervention
Measure the valve stem clearance
1. m Move the valve forward and backward in the direction of the arrow.
n Intake valve: 0.028 - 0.068 (+0 -0.015) mm
n Exhaust valve: 0.048 - 0.088 (+0 -0.015) mm

NOTE
Take the entire overturning stroke into consideration.

© 42597-0

Fig. 363
2. m Remove the magnetic stand for measurements.
m Disassemble the dial gauge.
m Assemble the valves.
See para. 30.3.13 - Valve assembly and dis... - page 30-45

© 42596-0

Fig. 364

30.3.16 - Replacing the valve guide (oversized - cast)

Commercially available tools:
l Reamers
l Limit plug gauges
l Machine for working the cylinder heads
l Press
l Industrial aspirator
l Helical drill bit
Special tools:
l Spacer bush
l Nitrogen (liquid)
DANGER
Risk of accident, do not touch super cooled components or liquid nitrogen!
Wear protective gloves and safety goggles!

WARNING
The process of pressure fitting must be carried out quickly due to the thermal shock between the cylinder head and
the inserted valve seat.
The necessary work steps must be carried out before pressure fitting.

30-52
Method of intervention
NOTE
When using the machine to process the cylinder heads, following the specific instructions provided by the manufac-
turer.

Check the valve guide

1. m Check the valve guide.
See para. 30.3.15 - Check the valve guide - page 30-51
m Check the valve guide with a limit plug gauge (1).
n Intake valve: 8.008 (+0.025, -0) mm
n Exhaust valve: 8.008 (+0.025, -0) mm
1
NOTE
The reference side of the limit plug gauge must be
able to move up and down with slight shrinkage.

© 39737-1

Fig. 365

Make the housing hole for the valve guide (increased dimension)
1. m Close the coolant channels.
m Tighten the cylinder head on the machine for processing the cylinder
heads.
m Align the cylinder head.

© 36644-1

Fig. 366
2. m With the guide bolt (1) align the drilling unit with respect to the hous-
ing hole.
NOTE
The housing holes may have different diameters,
therefore select a guide bolt suitable for aligning the 1

drilling units. The guide bolt must move easily without

noticing resistance in the housing hole.

© 36629-1

Fig. 367

30-53
 Method of intervention
3. m Drill the valve guide with a helical drill bit (1).
m Remove the swarf with an industrial vacuum.

© 36628-1

Fig. 368
4. m Grind the seat hole to the standard size: 15.000 (+0.011,-0) mm.
WARNING
The reamer twists in an anticlockwise direction and there-
fore must always be turned clockwise. Never turn the ream-
er anticlockwise. The shavings that form when removing
material can block and destroy the cutting edges.
m Blow compressed air through the housing hole.

© 36637-1

Fig. 369
5. m Check the housing hole for the valve guide using the limit plug
gauge (1).
n Standard: 15.000 (+0.011, -0) mm
n Interference: 15.250 (+0.011, -0) mm
n Interference: 15.500 (+0.011, -0) mm
1
NOTE
The reference side of the limit plug gauge must be
able to move up and down with slight shrinkage.
The no-go end of the go-no-go gauge must not pass
through the seat hole. If the no-go end of the gauge
fits in the hole, grind the hole to the next highest inter-
ference size. If the wear limit reached the 2nd degree
of oversizing, replace the cylinder head. © 36634-1

Fig. 370

30-54
Method of intervention
6. m Release the cylinder head.
m Blow compressed air on the cylinder head.

© 36644-1

Fig. 371

Pressure insertion of the valve guide

1. m Apply the cylinder head.
m Select a valve guide suitable for the housing hole.
n Standard: 15.000 (+0.034, +0.023) mm
n Interference: 15.250 (+0.034, +0.023) mm
n Interference: 15.500 (+0.034, +0.023) mm

© 36642-1

Fig. 372
2. m Supercool the valve guide with liquid nitrogen.
NOTE
Use containers suitable for liquid nitrogen and a tool
suitable for the component insertion and removal op-
erations. When starting to cool the metal, the liquid
nitrogen will boil intensely, the effervescence pro-
cess is maintained until the metal components reach
the temperature of the liquid nitrogen (-196 °C). The
guide valve will have the correct temperature once
the effervescence process of the nitrogen is con-
cluded.

© 36636-1

Fig. 373

30-55
 Method of intervention
3. m Fit the valve guide with the spacer bush (1).
NOTE
Be careful to fit the guide valve the right way round.
The valve seal groove must face upwards.

© 36635-1

Fig. 374
4. m Press-fit the valve guide flush in the respective surface using the
spacer bush (arrow).
m Remove the spacer bush.
NOTE
The new valve guide will protrude further than the
original valve guideIl .

m Remove the cylinder head.

m Assemble the valves.
See para. 30.3.13 - Valve assembly and dis... - page 30-45

© 36618-1

Fig. 375

30.3.17 - Check the valve residual

Commercially available tools:
l Depth gauge
Special tools:
l Support stand: 120900
l base plate: 120910
WARNING
If the wear limit of the inserted valve seat and/or the valve is reached, replace them.

30-56
Method of intervention
Check the valve residual
1. m Disassemble the cylinder head.
See para. 30.3.10 - Disassembly and assemb... - page 30-32 1
m Assemble the support stand (1) on the base plate (2).

© 44178-0

Fig. 376
2. m Fasten the cylinder head onto the mounting stand (1) and the base
plate (2).
1

© 46588-0

Fig. 377
3. m Measure the valve residual from the centre of the valve head with
respect to the sealing surface of the cylinder head.
n Intake valve: 0.9 (+0.15, -0.1) mm
n Exhaust valve: 0.9 (+0.15, -0.1) mm

© 42598-0

Fig. 378

30-57
 Method of intervention
4. m Disassemble the cylinder head from the support stand (1).
m Disassemble the base plate support stand (2).
m Assemble the cylinder head.
See para. 30.3.10 - Disassembly and assemb... - page 30-32 1

© 46588-0

Fig. 379

30.3.18 - Replacing the lined valve seat (oversized)

1. Commercially available tools:
m Pin milling cutter, 10 mm
m Internal bore meter
m Sliding gauge
m Machine for working the cylinder heads
m Press
m Industrial aspirator
m Presser
m Vertical drill

m Nitrogen (liquid)
DANGER
Risk of accident, do not touch super cooled components or liquid nitrogen!
Wear protective gloves and safety goggles!

WARNING
The process of pressure fitting must be carried out quickly due to the thermal shock between the cylinder head
and the inserted valve seat.
The necessary work steps must be carried out before pressure fitting.
NOTE
When using the machine to process the cylinder heads, following the specific instructions provided by the
manufacturer. To replace an inserted valve seat, the respective valve guide must be present.

2. m Check the valve residual.

See para. 30.3.17 - Check the valve residual - page 30-56
m Disassemble the valves.
See para. 30.3.13 - Valve assembly and dis... - page 30-45

© 42598-0

Fig. 380

30-58
Method of intervention
Checking the inserted valve seat
1. m Check the inserted valve seat (1).
NOTE
Check the installation position is correct. 1

© 36638-1

Fig. 381

Disassembly of the inserted valve seat

1. m Close the coolant channels.
m Tighten the cylinder head.
m Align the inserted valve seat with the pin milling cutter.

© 36632-1

Fig. 382
2. m Laterally cut the inserted valve seat (arrow) until it can be removed
without tension.
WARNING
Do not damage the cylinder head.

© 36639-1

Fig. 383

30-59
 Method of intervention
3. m Apply a protective sublayer (arrow).
m Remove the inserted valve seat by applying leverage.
WARNING
Do not damage the cylinder head.

m Release the cylinder head.

© 36631-1

Fig. 384

Check the hole of the housing for the inserted valve seat
1. NOTE
Measurement diagram hole of the housing in points “a and
b”, central in surface “1”. 1

© 36640-1

Fig. 385
2. m Measure the hole of the housing with an internal bore meter.
NOTE
Measurement points, see diagram.

m Read the value measured.

n Intake: 42.7 (+0.025, -0) mm
n 2 degrees of oversizing for: + 0.2 mm
n Exhaust: 36.9 (+0.025, -0) mm
n 2 degrees of oversizing for: + 0.2 mm

© 36621-1

Fig. 386

30-60
Method of intervention
3. NOTE
If the wear limit reached the 2nd degree of oversizing, re-
place the cylinder head. Alternatively, determine the diam-
eter of the seat hole with a measuring ring (1).
For example, a lined valve seat lathed to half its height may
be used as a measurement ring, which is then inserted in
the hole to measure the diameter.

© 36641-1

Fig. 387

Make the housing hole for the inserted valve seat (interference)
1. m Set the cutting tool.

© 36620-1

Fig. 388
2. m Tighten the cylinder head on the machine for processing the cylinder
heads.
m Close the coolant channels.
m Align the cylinder head.

© 36619-1

Fig. 389

30-61
 Method of intervention
3. NOTE
The valve guides may have different diameters, therefore
select a guide bolt suitable for aligning the drilling units. The
guide bolt must move easily without noticing resistance in
the valve guide.
1
m With the guide bolt (1) align the drilling unit with respect to the hous-
ing hole.

© 39738-1

Fig. 390
4. m Enlarge the housing hole based on the degree of oversizing.
WARNING
The inserted valve seat support (arrow) must not be ma-
chined with a cutting tool.

m Remove the shavings from the bottom.

© 36624-1

Fig. 391
5. m Measure the hole of the housing with an internal bore meter.

© 36621-1

Fig. 392

30-62
Method of intervention
Pressure insertion of the inserted valve seat
1. m Apply the cylinder head.
m Select a inserted valve seat suitable for the housing hole.
n Intake: 42.79 (+0, -0.02) mm
n Degree of oversizing: 42.99 mm
n Degree of oversizing: 43.19 mm
n Exhaust: 36.99 (+0, -0.02) mm
n Degree of oversizing: 37.19 (+0, -0.02) mm
n Degree of oversizing: 37.39 (+0, -0.02) mm

© 36626-1

Fig. 393
2. m Supercool the inserted valve seat in liquid nitrogen.
NOTE
Use containers suitable for liquid nitrogen and a tool
suitable for the component insertion and removal op-
erations. When starting to cool the metal, the liquid
nitrogen will boil intensely, the effervescence process
is maintained until the metal components reach the
temperature of the liquid nitrogen (-196 °C). The in-
serted valve seat will have the correct temperature
once the effervescence process of the nitrogen is
concluded.

© 36623-1

Fig. 394
3. m Position the inserted valve seat (1) on the presser (2).
NOTE
2
Observe the installation position. The valve seat sur-
face must face towards the presser tool.

© 36643-1

Fig. 395

30-63
 Method of intervention
4. m Insert the inserted valve seat (1) with the presser (2) in the housing
hole (3) to the stop (arrow).
m Remove the cylinder head. 2
m Machining the inserted valve seat.
m Assemble the valves.
See para. 30.3.13 - Valve assembly and dis... - page 30-45 1
m Check the valve residual.
See para. 30.3.17 - Check the valve residual - page 30-56
3

© 36633-1

Fig. 396

30.3.19 - Check the endfloat of the crankshaft

1. Commercially available tools:
m Magnetic stand for measurements
m Palmer
m Internal bore meter
m Box spanner insert: 8035

Special tools:
m Dial gauge: 100400

2. m Disassemble the front cover.

See para. 30.3.33 - Removal and refitting ... - page 30-123
m Disassemble the gear case cover.
See para. 30.3.36 - Disassembly and assemb... - page 30-135
m Apply the magnetic stand for measurements.
m Insert the dial gauge.
m Apply the preloaded probe on the end of the crankshaft.
m Press the crankshaft towards the arrow.
m Adjust the dial gauge to “0”.

© 44179-0

Fig. 397
3. m Press the crankshaft towards the arrow.
m Read the value measured: 0.1 - 0.3 mm
NOTE
If there is a difference in the endfloat, set the permit-
ted value by replacing the halves of the thrust ring.

© 44180-0

Fig. 398

30-64
Method of intervention
4. m Remove screws (1).
NOTE
Use the box spanner insert. 1

m Remove flanged bearing cover (2).

m Remove the lower bearing shell. 2
m Remove the two halves of the thrust ring (arrows).

© 44181-0

Fig. 399
5. m Remove the two halves of the thrust ring (arrows).

© 44182-0

Fig. 400
6. m Measure the thickness of the halves of the thrust ring.
n Standard: 2.00 (+0.05, -0) mm
n Interference: 2.20 (+0.05, -0) mm

m Select the thrust ring halves based on the measured value.

© 43504-0

Fig. 401

30-65
 Method of intervention
7. m Disassemble the crankshaft.
See para. 30.3.25 - Assembly and disassemb... - page 30-93
m Adjust the palmer to 32 mm.
m Push the internal bore meter between the test surfaces of the palm-
er and bring to “0”.

© 35825-2

Fig. 402
8. m Measure the width of the flanged bearing.
m Make a note of dimension (a).

© 42606-0

Fig. 403
9. m Apply the thrust ring halves on the flanged bearing cover (arrows).
m Measure the width with the palmer.
m Make a note of dimension (b).

© 35827-2

Fig. 404
10. m Calculate the endfloat: 0.1 - 0.3 mm
Table 57

Calculation example:
Target: Endfloat
Data: -
Measured value: (a) = 32.8 mm, (b) = 32.7 mm
Calculation: Dimension (a) - dimension (b)
The results of all this are: = 0.1 mm
m Assemble the crankshaft.
See para. 30.3.25 - Assembly and disassemb... - page 30-93

30-66
Method of intervention

30-67
 Method of intervention
14. m Insert the flanged bearing cover (1).
NOTE
The riser (arrow) of the flanged bearing cover is fac-
ing the manifold side.

1
© 44185-0

Fig. 408
15. m Tighten the screws (1) with the socket wrench insert. 50 Nm + 90°
+ 90°.
WARNING
In the case of written certification, the screws can be used
a maximum of 3 times. Otherwise, replace the screws each
time after being removed.

© 44186-1

Fig. 409
16. m Measure the endfloat of the crankshaft: 0.1 - 0.3 mm
m Remove the magnetic stand for measurements.
m Disassemble the dial gauge.
m Fitting the front cover.
See para. 30.3.33 - Removal and refitting ... - page 30-123
m Disassemble the gear case cover.
See para. 30.3.36 - Disassembly and assemb... - page 30-135

© 44187-0

Fig. 410

30-68
Method of intervention
30.3.20 - Check the crankshaft
Commercially available tools:
l Magnetic stand for measurements
l Palmer
l Internal bore meter
l Prisms
l Hardness tester
Special tools:
l Dial gauge: 100400
Check the hardness of the main journal
1. m Disassemble the crankshaft.
See para. 30.3.25 - Assembly and disassemb... - page 30-93
m Rest the crankshaft on the prisms.

© 42602-0

Fig. 411
2. m Apply the hardness tester on the bearing pins.

© 30560-1

Fig. 412
3. m Lift (1) the probe and press the release device (2).
NOTE
1
The probe (1) falls downward, briefly hits the surface
and goes up to the measurement value.

© 43499-0

Fig. 413

30-69
 Method of intervention
4. m Read the value indicated (arrow) by the hardness tester.
n Nominal, minimum value: 55 (+6) HRc

NOTE
The measurement values must be converted using
the tester table.

© 43515-0

Fig. 414
5. NOTE
Measurement diagram of the main journals on points 1 and
2 in surfaces a and b.

© 36424-2

Fig. 415

Check the diameter of the main bearing pins

1. m Measure the main bearing pins with the palmer.
n Standard: 84 (+0, -0.02) mm
n Degree of undersizing: 0.25 mm

NOTE
Measurement points, see diagram.

© 42603-0

Fig. 416

30-70
Method of intervention
Check the diameter of the connecting rod pins
1. m Measure the main journal with the palmer: 62.994 (+0, -0.02) mm
m Degree of undersizing: 0.25 mm
NOTE
Measurement points, see diagram.

© 42604-0

Fig. 417

Check the coaxiality

1. m Apply the magnetic stand for measurements.
m Insert the dial gauge.
m Apply the preloaded probe on the main bearing pins (arrow) and
adjust the dial gauge to “0”.
m Rotate the crankshaft at uniform speed and measure concencitrity:
0.1 mm
m Remove the magnetic stand for measurements.
m Disassemble the dial gauge.

© 42605-0

Fig. 418

Measuring the length of the flanged bearing

1. m Adjust the palmer to 32 mm.
m Push the internal bore meter between the test surfaces of the palm-
er and bring to “0”.

© 35825-2

Fig. 419

30-71
 Method of intervention
2. m Measure the width of the flanged bearing, placing the bore gauge
between the contact surfaces of the thrust rings: 32.2 (+0.04,-0) mm.
n Degree of undersizing: 0.4 mm

© 42606-0

Fig. 420

Visual inspection
1. m Inspect the sliding surfaces (1) of the crankshaft O-rings.
m Inspect the ring gear (2).
m Assemble the crankshaft.
See para. 30.3.25 - Assembly and disassemb... - page 30-93 1
1 2

© 42607-0

Fig. 421

30.3.21 - Replace the crankshaft O-ring (flywheel end)

Commercially available tools:
l Bradawl: 8198
l Assembly lever: 9017
Special tools:
l Assembly tool: 142830
l Self-tapping screw
l Washer

30-72
Method of intervention
Removal of the crankshaft oil seal
1. m Remove the flywheel.
See para. 30.3.64 - Removal and refitting ... - page 30-232
m Using a bradawl, make a hole about 3 mm in diameter in the old
crankshaft oil seal.
WARNING
Do not damage the gearbox cover or the crankshaft.

© 46472-0

Fig. 422
2. m Insert a self-tapping screw (1) with washer.

© 46561-0

Fig. 423
3. m Extract the crankshaft O-ring using the assembly lever.
m Carefully examine the crankshaft O-ring sliding surfaces.

© 46562-0

Fig. 424

30-73
 Method of intervention
Assembly of the crankshaft O-ring
1. m Fit guide bush (1).
m Tighten screws (2).
NOTE
The holes in the guide bush must be aligned with the
1
threaded holes in the crankshaft flange.

© 46563-0

Fig. 425
2. m Lightly oil the lip of the crankshaft O-ring.
m Carefully place the crankshaft O-ring on the sliding surface.
NOTE
The seal lip should be facing the engine crankcase.

© 46564-0

Fig. 426
3. m Fit spacer (1).
NOTE
If the crankshaft flange has an entry groove, the O-
ring can be installed at three different depths:
- First assembly = 2 washers. - 1. repair - assembly
level = 1 washer
- 2. repair - assembly level = 0 washers.

© 46565-0

Fig. 427

30-74
Method of intervention
4. m Fit installation bush (1).
m Push the crankshaft O-ring to the support.

© 46566-0

Fig. 428
5. m Insert bearing (1).
m Screw in nut (2);

2
© 46567-0

Fig. 429
6. m Screw in the nut until it seats against installation bush (1).
NOTE
The crankshaft oil seal is now installed at the correct
depth.
1
m Remove the installation tool.
m Fit the flywheel.
See para. 30.3.64 - Removal and refitting ... - page 30-232

© 44197-0

Fig. 430

30-75
 Method of intervention
30.3.22 - Replacing the crankshaft O-ring (opposite end to flywheel)
Commercially available tools:
l Bradawl: 8198
l Assembly lever: 9017
Special tools:
l Assembly tool: 142670
l Self-tapping screw
l Washer
Removal of the crankshaft oil seal
1. m Remove the V-belt pulley.
See para. 30.3.40 - Removing and fitting t... - page 30-146
m Using a bradawl, make a hole about 3 mm in diameter in the old
crankshaft oil seal.
WARNING
Be careful not to damage the front cover or the crankshaft.

© 43643-0

Fig. 431
2. m Insert a self-tapping screw (1) with washer.

© 44872-0

Fig. 432
3. m Extract the crankshaft O-ring using the assembly lever.
m Carefully examine the crankshaft O-ring sliding surfaces.

© 44873-0

Fig. 433

30-76
Method of intervention
Assembly of the crankshaft O-ring
1. m Remove tightening bush (1).

© 44875-0

Fig. 434
2. m Fit guide bush (1).
NOTE
Check that locating dowel (2) is aligned with hole (3). 1

© 42623-0

Fig. 435
3. m Tighten (1) the screws.

© 44877-0

Fig. 436

30-77
 Method of intervention
4. m Lightly oil the lip of the crankshaft O-ring.
m Carefully place the crankshaft O-ring on the sliding surface.
NOTE
The seal lip should be facing the engine crankcase.

© 44878-0

Fig. 437
5. m Fit spacer (1).
m Observe the assembly depth of the crankshaft O-ring and select a
suitable spacer disc.
n First installation depth = 2 shims
n Repair assembly depth = 1 spacer disc
n Maximum assembly depth = no washers

© 44879-0

Fig. 438
6. m Fit installation bush (1).
m Push the crankshaft O-ring to the support.

© 44880-0

Fig. 439

30-78
Method of intervention
7. m Insert bearing (1).
m Mutter (2) anschrauben.

2
1

© 44881-0

Fig. 440
8. m Screw in the nut until it seats against installation bush (1).
NOTE
The crankshaft oil seal is now installed at the correct 1
depth.

m Remove the installation tool.

© 44882-1

Fig. 441
9. m Insert bush (1) fully.
m Assemble the V-belt pulley.
See para. 30.3.40 - Removing and fitting t... - page 30-146

© 42622-0

Fig. 442

30-79
 Method of intervention
30.3.23 - Check the connecting rod drum
1. Commercially available tools:
m Palmer
m Internal bore meter
m Rotation angle gauge: 8190
m Connecting rod tester

Special tools:
m Dial gauge: 100400

2. m Disassemble the piston and connecting rod drum.

See para. 30.3.27 - Disassembly and assemb... - page 30-107
m Disassemble the piston from the connecting rod drum.

© 40592-1

Fig. 443

Check of the piston pin bush

1. m Prepare the internal bore meter:
n Fit the probes for the corresponding measurement interval in

an internal bore meter.

n Fit the dial gauge with a preload of approx. 1 mm in the inter-

nal bore meter.

n Adjust the palmer to 38 mm.
n Apply the internal bore meter between the test surfaces of

the palmer and in the return point of the pointer, bring the dial
gauge to “0”.

© 34768-2

Fig. 444
2. NOTE
Measurement diagram of the piston pin bush in points “a”
and “b” in surfaces “1” and “2”.

© 37239-1

Fig. 445

30-80
Method of intervention
3. m Insert the internal bore meter.
m Apply the internal bore meter to the measurement points required
occasionally and read the value measured in the return point of the
pointer: 38.025 (+0.010) mm.
NOTE
Measurement points, see diagram.

m Make a note of the measured value, dimension A.

NOTE
Dimension A is used to determine the piston pin
clearance.
© 34770-2

Fig. 446

Check the diameter of the piston pin

1. m Measure the piston pin with the palmer: 38 (+0,-0.006) mm.
m Make a note of the measured value, dimension B.
NOTE
Dimension B is used to determine the piston pin
clearance.

© 35908-2

Fig. 447

Calculate the piston pin clearance

1. NOTE
The piston pin free play is determined by the difference between the inner diameter of the piston pin bearing
shell (a) and the diameter of the piston pin (b): 0.025 - 0.041 mm

Table 58

Calculation example:
Target: Piston pin clearance
Data: -
Measured value: Inner diameter of piston pin bush (a), (a) = 38.025 mm. Diam-
eter of piston pin (b), (b) = 38.000 mm
Calculation: Measurement (a) - measurement (b), 38.025 mm - 38.000 mm
The results of all this are: = 0.025 mm

30-81
 Method of intervention
Check the connecting rod bearing hole
1. m Apply the flanged bearing cover.
WARNING

26519
Pay attention to coupling the flanged bearing cover. The nu- 1
meric marks (1) on the connecting rod drum and on the con-

26519
necting rod bearing cover must be identical and positioned
in front of each other during assembly.

© 44212-0

Fig. 448
2. m Alternatively tighten the screws with the rotation angle gauge and
the box spanner insert: 30 Nm + 60° + 30°

© 44213-0

Fig. 449
3. m Prepare the internal bore meter:
n Fit the probes for the corresponding measurement interval in

an internal bore meter.

n Fit the dial gauge with a preload of approx. 1 mm in the inter-

nal bore meter.

n Adjust the palmer to 66 mm.
n Apply the internal bore meter between the test surfaces of

the palmer and in the return point of the pointer, bring the dial
gauge to “0”.

© 36094-1

Fig. 450

30-82
Method of intervention
4. NOTE
Measurement diagram of the connecting rod bearing hole in
points “a” and “b” in surfaces “1” and “2”.

© 37239-1

Fig. 451
5. m Insert the internal bore meter.
m Apply the bore gauge to each of the measurement positions indicat-
ed and read the maximum value indicated by the dial: 66.6 (+0.019)
mm.
NOTE
If the measured values diverse minimally, take addi-
tional measurements with new bearing shells.

© 44214-0

Fig. 452

Check the internal diameter of the connecting rod bearing shells

1. m Unscrew the screws.
m Remove the flanged bearing cover.
NOTE
Check that tightening bush (1) is present.

© 44440-0

Fig. 453

30-83
 Method of intervention
2. m Insert the connecting rod bearing shell into the connecting rod drum.
WARNING
Take care to couple the bearing shells. The anti-twist safety
(1) must enter the groove (2).

1
© 44215-0

Fig. 454
3. m Insert the connecting rod bearing shell into the relative flanged bear-
ing cover.
WARNING
1
Take care to couple the bearing shells. The anti-twist safety
(1) must enter the groove (2).

© 44216-0

Fig. 455
4. m Apply the flanged bearing cover.
WARNING
2651

The numeric marks (1) on the connecting rod drum and on 1

9

the connecting rod bearing cover must be identical and po-

2651

sitioned in front of each other during assembly.

9

© 44217-0

Fig. 456

30-84
Method of intervention
5. m Alternatively tighten the screws with the rotation angle gauge and
the box spanner insert: 30 Nm + 60° + 30°.

© 44218-0

Fig. 457
6. m Prepare the internal bore meter:
n Fit the probes for the corresponding measurement interval in

an internal bore meter.

n Fit the dial gauge with a preload of approx. 1 mm in the inter-

nal bore meter.

n Adjust the palmer to 63 mm.
n Apply the internal bore meter between the test surfaces of

the palmer and in the return point of the pointer, bring the dial
gauge to “0”.

© 36094-1

Fig. 458
7. NOTE
Measurement diagram of the internal diameter of the con-
necting rod bearing shells in points “a” and “b” in surfaces
“1” and “2”.

© 37239-1

Fig. 459

30-85
 Method of intervention
8. m Insert the internal bore meter.
m Apply the internal bore meter to the measurement points required
occasionally and read the value measured in the return point of the
pointer.
NOTE
See diagram for measurement points: 63.026 -
63.065 mm.

m Make a note of dimension (a).

NOTE
The connecting rod drum wear limit was reached,
replace it.
© 44219-0

Fig. 460

Check the diameter of the connecting rod pins

1. NOTE
Measurement diagram of the main journals on points 1 and
2 in surfaces a and b.

© 36424-2

Fig. 461
2. m Measure the main journal with the palmer: 62.994 (+0,-0.02) mm.
n Degree of undersizing: 0.25 mm.

NOTE
Measurement points, see diagram.

m Make a note of dimension (b).

© 36424-2

Fig. 462

30-86
Method of intervention
Determine the clearance of the connecting rod bearing
1. NOTE
The big end bearing free play is determined by the difference between the inner diameter of the big end bearing
shell (a) and the diameter of the crankpin (b): 0.032 - 0.073 mm.

Table 59

Calculation example:
Target: Clearance of the connecting rod bearing
Data: -
Measured value: Inner diameter of big end bearing shell (a), (a) = 63.026 mm.
Diameter of crankpins (b), (b) = 62.992 mm
Calculation: Dimension (a) - dimension (b)
The results of all this are: = 0.034 mm
m n Wear limit: 0.12 mm
2. m Unscrew the screws.
m Remove the flanged bearing cover.

© 44218-0

Fig. 463

Check the connecting rod drum

1. m Assemble the connecting rod drum without bearing shells on the
tester. A
WARNING
It is not permitted to straighten the connecting rod drum. B

m Move the test fork towards the arrow.

m Check the parallelism of the connecting rod drum.
m Difference permitted from (A) to (B): 0.04 mm.
NOTE
Distance between “A“ and “B“ = 100 mm.
© 30579-1

Fig. 464

30-87
 Method of intervention
2. m Move the test fork towards the arrow.
m Check the angulation of the connecting rod drum.
m Difference permitted from (C) to (D): 0.04 mm.
NOTE
Distance between “C“ and “D“ = 100 mm. C

D
m Complete the piston and the connecting rod drum.
m Assemble the piston and the connecting rod drum.
See para. 30.3.27 - Disassembly and assemb... - page 30-107

© 30580-1

Fig. 465

30.3.24 - Fitting and removing piston pin bush

Commercially available tools:
l Press or threaded pin
Special tools:
l base plate: 131200
l Set of assembly tools: 131220
l Nitrogen (liquid)
l Degreaser/detergent
l Compressed air
l Heating device
DANGER
Risk of accident, do not touch hot components! Risk of accident, do not touch super cooled components or liquid
nitrogen! Wear protective gloves and safety goggles!

WARNING
The process of pressure fitting must be carried out quickly due to the thermal shock between the bush of the piston pin
and the connecting rod drum. The necessary work steps must be carried out before pressure fitting.

NOTE
The extraction of the piston pin bush is illustrated with a pneumatic press. Alternatively, also a threaded pin can be
used.

30-88
Method of intervention
Disassembly of the piston pin bush
1. WARNING
3
Never force the piston pin bush!

1
m Insert the housing of the connecting rod bearing (3) in the base plate
(2).
m Insert the disassembly gauge (1) in the base plate.
WARNING
Do not mix up the disassembly gauge and the assembly
gauge! 2

NOTE © 40404-1

The groove (arrow) must face the housing of the connect- Fig. 466
ing rod bearing. Make sure that the disassembly gauge is
perfectly levelled.
2. m Insert the lower part of the assembly tool (3) from below in the disas-
sembly gauge. 1 2
m Position the connecting rod drum (1) on the base plate.
NOTE
The flat side (arrow) of the connecting rod drum must
face downwards.

m Rotate the lower part (3) in the upper part (2) of the assembly tool.

© 40403-1

Fig. 467
3. m Align the upper part (1) of the assembly tool with the disassembly
gauge (2).
NOTE
The upper part of the assembly tool and the disas-
sembly gauge are flush with the angular surfaces (ar-
1
row) of the connecting rod bearing.
2

© 40401-1

Fig. 468

30-89
 Method of intervention
4. m Tighten the upper part (1) and the lower part (2) of the assembly
tool.

© 40402-1

Fig. 469
5. m Align the pneumatic press horizontally with the base plate.
NOTE
The extractor punch must be situated in the centre
above the top of the assembly tool.

© 36284-3

Fig. 470
6. m Remove the piston pin bush with slight pressure.
m Clean the hole in the bush.
NOTE
The hole in the bush must be free of grease and dirt.

© 36285-3

Fig. 471

30-90
Method of intervention
Assembly of the piston pin bush
1. m Insert the housing of the connecting rod bearing (3) in the base plate
(2). 3
m Insert the assembly gauge (1) in the base plate.
NOTE
1
The groove (arrow) must face the housing of the con-
necting rod bearing. Make sure that the assembly
gauge is perfectly levelled.

© 40405-1

Fig. 472
2. m Heat the connecting rod shank (1): 220 °C.
m Position the connecting rod drum on the base plate (2).
NOTE 1
The flat side (arrow) of the connecting rod drum must
face downwards.

© 40406-1

Fig. 473
3. m Chill the piston pin bush (1) in liquid nitrogen to approximately -40
°C.

© 36288-2

Fig. 474

30-91
 Method of intervention
4. m Position the supercooled bush of the piston pin (1) on the assembly
bolt (3). 1
NOTE
The index (2) must be situated in the groove (indi-
cated by arrow) in the piston pin bush.

2
3

© 40407-1

Fig. 475
5. m Insert the assembly bolt (1) with the piston pin bush (2) in the hole
of the connecting rod.
NOTE
The piston pin bush must be inserted without force 1
into the connecting rod hole. Pay attention to the as-
sembly position of the piston pin bush.
m Remove the assembly bolt. 2
NOTE
The piston pin bush must not slip any more.

© 36290-4

Fig. 476
6. m Check the assembly position.
NOTE
Position of bush separation line (indicated by arrow)
as seen when looking towards the flat side of the
connecting rod shank.

© 40968-1

Fig. 477

30-92
Method of intervention
7. NOTE
After the assembly operation, mechanically adjust the piston
pin bush.

m Turn the piston pin bush to dimension A.

Table 60

Dimension Maximum dimension Minimum dimension

Hole of the piston pin 38.035 mm 38.025 mm
bush, dimension A
Piston pin diameter 38.000 mm 37.994 mm
Theoretical clearance 0.041 mm 0.025 mm © 39730-2

Fig. 478

30.3.25 - Assembly and disassembly of the crankshaft

Special tools:
l Box spanner insert: 8035
l Rotation device: 100330
Disassembly of the piston pin bush
1. m Disassemble the front cover.
See para. 30.3.33 - Removal and refitting ... - page 30-123
m Disassemble the gear case cover.
See para. 30.3.36 - Disassembly and assemb... - page 30-135

© 42647-2

Fig. 479
2. m Tighten screws (1).
m Disassemble all the connecting rod bearing covers.
m Remove the connecting rod bearing shells.
See para. 30.3.27 - Disassembly and assemb... - page 30-107

© 42648-1

Fig. 480

30-93
 Method of intervention
3. m Place the mark of reference (1) on the ring gear of the camshaft.
NOTE 2

The reference mark must be located on a line be-

tween the marking (2) and the mid point (3) of the
camshaft. 1

© 42651-0

Fig. 481
4. m Uniformly rotate the crankshaft until the mark (1) on the flange of the
shaft coincides with the auxiliary mark (2) on the camshaft ring gear.
NOTE
If the crankshaft flange is aligned, the mark on the 1
camshaft ring gear will be covered.

WARNING
2
Do not bend the connecting rod drums while rotating the
crankshaft.

© 42652-0

Fig. 482

Disassembly of the main bearing cover

1. m Unscrew all the screws (1) using the long reach socket.

© 42653-1

Fig. 483

30-94
Method of intervention
2. m Remove flanged bearing cover (1).
m Remove the bearing shell.
m Remove the two halves of the thrust ring (arrows).
m Remove all the main bearing covers (2).
m Remove the bearing shells.
1
NOTE
Put the components to one side in the order in which
they were removed. Note the cylinder order.
2

© 44228-1

Fig. 484
3. m Delicately extract the connecting rod drums from the relative pins.
m Extract the crankshaft by applying leverage.

© 42655-1

Fig. 485
4. m Remove the two halves of the thrust ring (arrows).
m Remove all the main bearing shells (1).
NOTE
Put the components to one side in the order in which
they were removed. Note the cylinder order.
1
m Carry out a visual inspection of the components.
m Check the endfloat of the crankshaft (disassembled crankshaft).
See para. 30.3.19 - Check the endfloat of ... - page 30-64
See para. 30.3.20 - Check the crankshaft - page 30-69

© 44231-2

Fig. 486

30-95
 Method of intervention
Assembly of the crankshaft
1. m Insert the upper shells of the main bearings.
NOTE
Take care to couple the bearing shells. The anti-twist
safety (1) must enter the groove (2).
1

© 42658-0

Fig. 487
2. m Insert the lower shells of the main bearings in the relative main bear-
ing covers.
NOTE
1
Take care to couple the bearing shells. The anti-twist
safety (1) must enter the groove (2).

© 44233-0

Fig. 488
3. NOTE
Make sure all the tightening bushes are present (arrows).

© 44231-1

Fig. 489

30-96
Method of intervention
4. m Position the camshaft.
NOTE
Align the hole (1) in the direction of the cylinder head.

m Oil the surfaces of the bearings.

© 42661-0

Fig. 490
5. m Delicately insert the crankshaft in the crankcase.
WARNING
Do not bend the connecting rod drums while inserting the
crankshaft!

m Move the crankshaft in correspondence of the camshaft.

NOTE
Make sure the marks line up.

© 44238-2

Fig. 491
6. m Check the control times.
NOTE
The mark (1) on the flange of the crankshaft must line
up with the reference mark (2). 1

© 42652-0

Fig. 492

30-97
 Method of intervention
7. m Assemble the upper thrust ring halves based on the measured end-
float.
NOTE
Thrust ring halves without the key, between the
crankshaft and crankcase (arrows). The oil grooves 2
(1) in the thrust ring halves face towards the thrust
discs (2) of the crankshaft (arrows).
1

© 42662-0

Fig. 493
8. m Fix the two thrust ring halves with a small amount of grease on the
flanged bearing cover.
NOTE
Flanged bearing cover marked with “2”. Use the
halves of the thrust ring with the key (arrow). The

2
oil grooves (1) face towards the shoulder disc of the
crankshaft.

© 42663-0

Fig. 494

Assembly of the main bearing cover

1. m Insert the flanged bearing cover (1).
m Insert the main bearing cover (2) based on the numbering.
Pay attention to the attribution and assembly po-
sition:
Insert the main bearing cover with number 1 on the 1
flywheel side. The end (arrow) of the bearing cover is
facing the curve side. 7 6 5 4 3 2 1

© 44240-1

Fig. 495

30-98
Method of intervention
2. m Main bearing cover with socket wrench insert and rotation angle
gauge: 50 Nm + 90° + 90°.
WARNING
In the case of written certification, the screws can be used
a maximum of 3 times. Otherwise, replace the screws each
time after being removed.
m Assemble the flanged bearing cover.
See para. 30.3.27 - Disassembly and assemb... - page 30-107

© 44241-1

Fig. 496
3. m Remove screws (1).

© 42648-1

Fig. 497
4. m Assemble the gear case cover.
See para. 30.3.36 - Disassembly and assemb... - page 30-135
m Fitting the front cover.
See para. 30.3.33 - Removal and refitting ... - page 30-123

© 42647-2

Fig. 498

30-99
 Method of intervention
30.3.26 - Fitting and removing counterweight shafts, checking
Commercially available tools:
l Palmer
l Torque wrench
Special tools:
l Alignment pins (q.ty 2): 100810
l Plaster
l DEUTZ DW 72 mastic
Removing counterweight shafts
1. m Disassemble the gear case cover.
See para. 30.3.36 - Disassembly and assemb... - page 30-135
m Bring cylinder piston 1 to top dead centre.
NOTE
The mark (1) on the flange of the crankshaft must line
up with the reference mark (2).

© 36652-2

Fig. 499
2. m Remove screw (1).
m Remove washer (2).
m Remove the intermediate wheel (3).
m Remove the bearing pin.

3
2

© 46605-0

Fig. 500
3. m Remove screw (1).
m Remove lube oil pipe (2).
m Remove the intermediate wheel (3).
m Remove the bearing pin.
1

© 46606-0

Fig. 501

30-100
Method of intervention
4. m Remove screws (1).
m Remove the shims (2).

1
1

2
2

© 46607-0

Fig. 502
5. m Remove the counterweight shafts in the direction indicated by the
arrow.
WARNING
Take care not to damage the counterweight shafts.

© 36666-3

Fig. 503

Checking counterweight shafts

1. m Visually check the wear of the components.

© 36664-1

Fig. 504

30-101
 Method of intervention
2. m Measure the diameter of the main journals with the palmer: 54
(-0.02) mm.

© 36665-1

Fig. 505

Fitting counterweight shafts

1. m Oil the bearing pins slightly.
m Fit the counterweight shafts in the direction indicated by the arrow.
NOTE
The weight (1) must face towards the lubricant oil
sump pan.

1
© 36666-4

Fig. 506
2. m Undo the screw plugs (1).

© 36651-2

Fig. 507

30-102
Method of intervention
3. m Insert the centring pins (1).
m Fasten the counterweight shafts with the alignment pins (1).
WARNING 1

Stop rotating the mass compensation shaft.

© 36659-2

Fig. 508
4. m Fit the shims (2).
m Tighten screws (1).
NOTE
Do not tighten the screw at this stage.

1
1

2
2

© 46607-0

Fig. 509
5. m Assemble the B side intermediate wheel.
NOTE
2
Centre the intermediate wheel (1) with respect to the
threaded hole (2). If the sides of the teeth do not co-
incide with the crankshaft, it can be rotated easily.

WARNING
Stop rotating the mass compensation shaft.

© 36669-1

Fig. 510

30-103
 Method of intervention
6. m Lightly oil the bearing pins (1).
m Insert the bearing pins (1).
m Fit washer (2).
m Screw in the screw (3).
NOTE
Insert the screw with DEUTZ DW 72 sealant. Do not 1
tighten the screw at this stage.

2
© 36670-2

Fig. 511
7. m Apply the reference marks (1) and (2).
m Unscrew the centring pins (side A).
m Turn the mass compensation shaft of the two teeth in the direction
of the arrow. 1

© 36656-2

Fig. 512
8. m From above, engage the intermediate wheel (1) in the toothing.
NOTE
Turn the mass compensation shaft in the direction of
the arrow until the reference marks coincide. Centre
the intermediate wheel (1) with respect to the thread- 1

ed hole (2).

© 36657-2

Fig. 513

30-104
Method of intervention
9. m Lightly oil the bearing pins (1).
m Insert the bearing pins (1).

© 36667-2

Fig. 514
10. m Fit new O-ring (1).

© 36668-2

Fig. 515
11. m Fit lube oil pipe (1).
m Tighten screws (2).
NOTE
Fit the screw, applying DEUTZ DW 72 thread lock 1
compound. Do not tighten.

© 36658-2

Fig. 516

30-105
 Method of intervention
12. m Remove all the alignment pins (1).

© 36659-2

Fig. 517
13. m Insert the new O-rings.
m Tighten the screw plugs (1). 9 Nm.

© 36651-2

Fig. 518
14. m Tighten the screws (1): 29 Nm.
m Tighten the screws (2): 22 Nm.
m Assemble the gear case cover.
See para. 30.3.36 - Disassembly and assemb... - page 30-135

1
2

© 36660-2

Fig. 519

30-106
Method of intervention
30.3.27 - Disassembly and assembly of the piston and connecting rod drum
Commercially available tools:
l Rotation angle gauge: 8190
Special tools:
l Piston ring compression collar 130670
NOTE
Collect operating materials in suitable containers and dispose of them in compliance with the applicable regulations.
The lubricant oil and the coolant must be added according to the user manual.

Disassembly of the piston and connecting rod drum

1. m Disassemble the cylinder head.
See para. 30.3.10 - Disassembly and assemb... - page 30-32
m Remove the oil suction pipe.
See para. 30.3.53 - Removal and refitting ... - page 30-198
m Withdraw the oil level dipstick.

© 46477-0

Fig. 520

Disassembly of the flanged bearing cover

1. m Rotate the crankshaft using the rotation device.
m Move the connecting rod pins to the bottom dead centre.
m Remove screws (1).
m Remove flanged bearing cover (2).
NOTE
Put the components to one side in the order in which
2
they were removed. Note the cylinder order. 1

m Remove the bearing shell.

© 46480-0

Fig. 521

30-107
 Method of intervention
2. m Disassemble the piston and connecting rod drum.
NOTE
Put the components to one side in the order in which
they were removed. Note the cylinder order.

© 46478-0

Fig. 522
3. m Remove the connecting rod bearing shells (1).
m Carry out a visual inspection of the components.

1
© 44250-0

Fig. 523
4. m Remove the circlip.
m Pressure remove the piston pin.
m Carry out a visual inspection of the components.

© 44251-0

Fig. 524

30-108
Method of intervention
Completion of the piston and connecting rod drum
1. m Insert a new circlip.
NOTE
Check the installation position is correct.

© 44252-0

Fig. 525
2. m Insert the connecting rod drum.
NOTE

26519
2
The flywheel/crankshaft symbol (1), on the bottom of
the piston, must face towards the right and numeric
code (2) on the connecting rod drum must face up-
wards.

© 44253-0

Fig. 526
3. m Lightly oil the piston pin.
m Pressure insert the piston pin.
m Insert a new circlip.
NOTE
Check the installation position is correct.

© 44254-0

Fig. 527

30-109
 Method of intervention
Assembly of the piston and connecting rod drum
1. NOTE
Check that tightening bush (1) is present.

1
1
© 46296-0

Fig. 528
2. m Insert the connecting rod bearing shell into the connecting rod drum.
NOTE
Take care to couple the bearing shells. The anti-twist
safety (1) must enter the groove (2).
2

1
© 46295-0

Fig. 529
3. m Insert the connecting rod bearing shell into the relative flanged bear-
ing cover.
WARNING
1
Take care to couple the bearing shells. The anti-twist safety
(1) must enter the groove (2).

© 44216-0

Fig. 530

30-110
Method of intervention
4. m Offset the piston ring joints by approx. 120°.
m Check the piston rings and grooves.
See para. 30.3.29 - Check the piston rings... - page 30-115

© 42380-1

Fig. 531
5. m Lightly oil the cylinder sliding surface, piston, piston rings and con-
necting rod pins.
m Tighten the piston rings with a compression collar (1).
NOTE
Never rotate the piston rings.

© 44255-0

Fig. 532
6. m Move the connecting rod pins to the bottom dead centre.
m Insert the piston and connecting rod drum in the cylinder liner.
NOTE
Pay attention to the piston cylinder allocation. Mark
the assembly position on the bottom of the piston. 1
The flywheel/crankshaft symbol (1) must be facing
the flywheel. The piston ring compression collar must
rest lightly on the cylinder liner.

© 45004-1

Fig. 533

30-111
 Method of intervention
7. m Delicately press the connecting rod drum against the connecting rod
pins.
WARNING
Do not bend the connecting rod drum with the crankshaft.

© 46481-0

Fig. 534

Assembly of the flanged bearing cover

1. m Apply the flanged bearing cover.

© 46482-0

Fig. 535
2. m Tighten the new screws using the rotation angle gauge> 30 Nm +
60° + 30°.
WARNING
The screws must be renewed after being removed.

© 46483-0

Fig. 536

30-112
Method of intervention
3. m Insert the oil level dipstick.
m Fit the oil suction pipe.
See para. 30.3.53 - Removal and refitting ... - page 30-198
m Assemble the cylinder head.
See para. 30.3.10 - Disassembly and assemb... - page 30-32

© 46479-0

Fig. 537

30.3.28 - Check the piston

Commercially available tools:
l Palmer
l Internal bore meter
Special tools:
l Dial gauge: 100400
NOTE
If the piston wear limit was reached, replace it.

Check of the piston pin hole

1. m Disassemble the piston from the connecting rod drum.
See para. 30.3.27 - Disassembly and assemb... - page 30-107

© 44262-0

Fig. 538

30-113
 Method of intervention
2. m Prepare the internal bore meter:
n Fit the probes for the corresponding measurement interval in

an internal bore meter.

n Fit the dial gauge with a preload of approx. 1 mm in the inter-

nal bore meter.

n Adjust the palmer to 38 mm.
n Apply the internal bore meter between the test surfaces of

the palmer and in the return point of the pointer, bring the dial
gauge to “0”.

© 34768-2

Fig. 539
3. NOTE
Measurement diagram of the piston pin hole in points “a”
and “b” in surfaces “1” and “2”.

© 37239-1

Fig. 540
4. m Insert the internal bore meter in the piston pin hole.
m Apply the internal bore meter to the measurement points required
occasionally and read the value measured in the return point of the
pointer: 38 (+0.009,-0.004) mm.
NOTE
Measurement points, see diagram.

© 43483-0

Fig. 541

30-114
Method of intervention
Check the piston diameter
1. NOTE
Measurement diagram of the piston diameter in points “1, 2
and 3”, transversal to the piston pin hole.

© 37244-1

Fig. 542
2. m Measure the clearance of the piston pin with the palmer.
Table 61

Diameter
Measurement height Standard Interference:
16 mm 100.820 (+0.009, 101.320 (+0.009,
-0.009) mm -0.009) mm
50 mm 100.588 (+0.007, 101.088 (+0.007,
-0.007) mm -0.007) mm
78.5 mm 100.270 (+0.012, 100.770 (+0.012,
-0.012) mm -0.012) mm

© 43427-0
NOTE
Fig. 543
Measurement points, see diagram.

m Complete the connecting rod drum and piston.

See para. 30.3.27 - Disassembly and assemb... - page 30-107

30.3.29 - Check the piston rings and piston grooves

Commercially available tools:
l Feeler gauges
Special tools:
l Universal pliers for piston rings: 130300
l Trapezoidal groove wear gauge: 130440

30-115
 Method of intervention
Check the piston rings and piston grooves
1. m Remove the piston from the connecting rod shank
See para. 30.3.27 - Disassembly and assemb... - page 30-107
m Set the universal piston ring tool for the piston diameter: 101 mm.
m Disassemble the piston ring with universal pliers.

Fig. 544
2. m Clean the piston.
m Inspect the piston.
m Visually inspect the piston grooves.

Fig. 545
3. m Measure the race of the first piston ring using a trapezoidal race
wear gauge.

© 33866-3

Fig. 546

30-116
Method of intervention
4. m
NOTE:
If there is a distance “S” between the trapezoidal S
race wear gauge and the piston, the piston can still
be used.

© 33867-3

Fig. 547
5. m
NOTE:
If the trapezoidal race wear gauge rests on the piston
(arrow) the latter must be replaced.

© 33868-3

Fig. 548

Check the coupling clearance of the piston rings

1. m Insert the piston ring (1) in the cylinder.
m Align the rings, pushing the piston into the cylinder.

© 45011-1

Fig. 549

30-117
 Method of intervention
2. m Measure the coupling clearance of the piston rings with the feeler
gauge.
n Piston ring = dual trapezoid section rings: 0.20 - 0.35 mm
n Piston ring = conical section ring: 1.5 - 2.0 mm
n Piston ring = oil scraper ring: 0.3 - 0.55 mm

m
NOTE
The piston ring wear limit was reached, replace it.

© 45012-1

Fig. 550
3. m Assemble the piston rings.
m Sequence and position of the piston rings viewed from the bottom
of the piston:
n Double trapezoidal ring (1)
1
n tapered ring (2)
2
n Oil scraper ring with tubular spring (3)
n
NOTE: 3

The mark “Top” faces towards the combustion

chamber.

© 44267-0

Fig. 551
4. m Assemble the piston ring with universal pliers.
NOTE:
Offset the flexible coupling of the oil scraper ring by
180° with respect to the ring coupling.

Fig. 552

30-118
Method of intervention
Check the endfloat of the piston ring
1. m
NOTE:
Perform the check with new piston rings.

m Check the endfloat between the piston and the groove of the piston
ring using the feeler gauge.
n Piston ring: 0.06 - 0.08 mm
n Piston ring: 0.02 - 0.04 mm

m
NOTE:
If the piston wear limit was reached, replace it.

Fig. 553
2. m Complete the connecting rod drum and piston.
See para. 30.3.27 - Disassembly and assemb... - page 30-107

Fig. 554

30.3.30 - Assembly and disassembly of piston cooling nozzles

Disassembly of the piston cooling nozzles
1. m Disassemble the crankshaft.
See para. 30.3.25 - Assembly and disassemb... - page 30-93
m Delicately tighten the self-tapping screw (1) into the piston cooling
nozzle.

Fig. 555

30-119
 Method of intervention
2. m Remove the piston cooling nozzle (1) with the pliers.

Fig. 556

Assembly of the piston cooling nozzles

1. m Clean the holes for the piston cooling nozzles in the crankcase.
m With the bolt, insert a new piston cooling nozzle (1) to the stop.
m Assemble the crankshaft.
See para. 30.3.25 - Assembly and disassemb... - page 30-93

Fig. 557

30.3.31 - Removal and refitting of the crankcase breather

Commercially available tools:
l Circlip pliers: 9090
Removal of the crankcase breather
1. m Loosen the circlip using the specific pliers and remove it towards
the bottom.
m Remove the flexible hose (1).
m Remove screws (2). 3
m Remove the crankcase breather (3). 2

© 46473-3

Fig. 558

30-120
Method of intervention
2. m Visually inspect the component.
m Clean the mating surfaces.
m Fit a new gasket (1)
1

© 46475-0

Fig. 559
3. m Fit the crankcase breather (1).
NOTE:
Make sure the assembly position is correct (arrow).
1

© 46476-0

Fig. 560
4. m Tighten the screws (1): 21 Nm
m Position the flexible pipe (2).
m Position the circlip with the specific pliers.

© 46473-4

Fig. 561

30-121
 Method of intervention
30.3.32 - Check the cylinder
Commercially available tools:
l Palmer
l Internal bore meter
l Depth gauge
Special tools:
l Dial gauge: 100400
NOTE
To measure the cylinder, the crankshaft bearing covers must be assembled regularly.

Check the cylinder

1. m Disassemble the piston and connecting rod drum.
See para. 30.3.27 - Disassembly and assemb... - page 30-107
m Visually check the wear of the cylinder.

Fig. 562
2. m Prepare the internal bore meter:
n Fit the probes for the corresponding measurement interval in

an internal bore meter.

n Fit the dial gauge with a preload of approx. 1 mm in the inter-

nal bore meter.

n Adjust the palmer to 101 mm.
n Apply the internal bore meter between the test surfaces of

the palmer and in the return point of the pointer, bring the dial
gauge to “0”.

Fig. 563

30-122
Method of intervention
3. NOTE
Measuring diagram of the cylinder liner in points “a” and “b”
in surfaces “1” -
“3”.

Fig. 564
4. m Insert the internal bore meter in the cylinder.
m Apply the internal bore meter to the measurement points required
occasionally and read the value measured in the return point of the
pointer.
m Compare the value measured with the nominal value. 101 (+0.02,
-0) mm
NOTE
Measurement points, see diagram.

m Assemble the piston and the connecting rod drum.

See para. 30.3.27 - Disassembly and assemb... - page 30-107

Fig. 565

30.3.33 - Removal and refitting of the front cover (opposite end to flywheel)
Removal of the front cover
1. m Remove the torsional vibration damper
See para. 30.3.40 - Removing and fitting t... - page 30-146
m Remove the oil suction pipe.
See para. 30.3.53 - Removal and refitting ... - page 30-198

Fig. 566

30-123
 Method of intervention
2. m Turn the engine on the assembly stand.
m Remove all the screws (1).
m Remove the front cover.
m Remove the gasket.

Fig. 567
3. m Visually inspect the components.

© 42996-0

Fig. 568

Refitting the front cover.

1. m Remove crankshaft seal (1).
WARNING
Be careful not to damage the mating surfaces when remov-
ing the front cover.

© 42997-0

Fig. 569

30-124
Method of intervention
2. NOTE
Check that tightening bush (1) is present.

m Fit a new gasket.

© 44545-1

Fig. 570
3. m Position the internal rotor relative to the crankshaft.
NOTE
The machining on the crankshaft and the rotor guides
must coincide. The internal rotor can only be fitted to
the crankshaft in one position.

© 44547-1

Fig. 571
4. m Fit the front cover.
m Fit the screws.
NOTE
Do not tighten the screws at this stage.

m Position the front cover flush with the mating surface of the oil sump
pan.

© 44548-1

Fig. 572

30-125
 Method of intervention
5. m Trim any protruding gasket (arrowed) flush with the mating surface
of the oil sump pan.

© 44551-1

Fig. 573
6. m Tighten the screws in the sequence indicated.
n Pretightening value: 3 Nm.
n Retightening value: 21 Nm.

Fig. 574
7. m Fill the oil pump housing with lubricating oil.

Fig. 575

30-126
Method of intervention
8. m Fit the oil suction pipe.
See para. 30.3.53 - Removal and refitting ... - page 30-198

Fig. 576
9. m Turn the engine on the assembly stand.
m Fit the front crankshaft oil seal (opposite end to flywheel)
See para. 30.3.22 - Replacing the cranksha... - page 30-76

Fig. 577
10. m Fit the torsional vibration damper.
See para. 30.3.40 - Removing and fitting t... - page 30-146

Fig. 578

30-127
 Method of intervention
30.3.34 - Disassembly and assembly of the connector box
Commercially available tools:
l Box spanner insert: 8113
l Box spanner insert: 8114
Disassembly of the connector box
1. m Remove screws (1).
m Remove cover (2)

1
© 42698-1

Fig. 579
2. m Remove screws (1).
m Remove the connector box.
NOTE
1
Use the box spanner insert.
1

m Visually inspect the components. 1

1 1

1
© 42699-1

Fig. 580

Assembly of the connector box

1. m Clean the support surfaces.
1
NOTE
Check that tightening bush (1) is present.
1

© 44083-1

Fig. 581

30-128
Method of intervention
2. m Apply the connector box.
m Centre the connector box above the tightening bushes. 1
m Fit the screws.
NOTE 2
1
Note that the screws are of different lengths M12 =
2
(1). M16 = (2) 1
1

2
© 42703-1
44083-1

Fig. 582
3. m Tighten the screws in the sequence indicated.
NOTE 4 2

Tightening sequence, see graph. Use the box span-

ner insert. 1
6

m Tighten the screw (1) manually.

m Pretension in order screws (2), (3) (4) and (5).
n Pretightening value: 99 Nm.

m Tighten screws (1) and (6). 99 Nm.

m Tightening alternatively screws (2), (3), (4) and (5). 3 5
n Retightening value: 243 Nm.

© 44085-0

Fig. 583
4. m Push the casing to the support.
m Tighten the screws (2): 9 Nm. 1

NOTE
2
The slot (1) is facing the oil sump.

© 42704-1

Fig. 584

30-129
 Method of intervention
30.3.35 - Fitting and removing the camshaft bearings, checking
Commercially available tools:
l Palmer
l Internal bore meter
Special tools:
l Dial gauge: 100400
l Assembly tool: 143840
Check the camshaft bearings
1. m Disassemble the crankshaft.
See para. 30.3.25 - Assembly and disassemb... - page 30-93
m Disassemble the camshaft.
See para. 30.3.37 - Assembly and disassemb... - page 30-139

Fig. 585
2. m Prepare the internal bore meter:
n Fit the probes for the corresponding measurement interval in

an internal bore meter.

n Fit the dial gauge with a preload of approx. 1 mm in the inter-

nal bore meter.

n Adjust the palmer to 70 mm.
n Apply the internal bore meter between the test surfaces of

the palmer and in the return point of the pointer, bring the dial
gauge to “0”.

Fig. 586
3. NOTE
Measurement diagram of the camshaft bearing in points “a”
and “b” in surfaces “1” and “2”.

© 37239-1

Fig. 587

30-130
Method of intervention
4. m Insert the internal bore meter.
m Apply the internal bore meter to the measurement points required
occasionally and read the value measured in the return point of the
pointer: 63 (+0.054) mm
n Wear limit: 63.080 mm

NOTE
Measurement points, see diagram. If the camshaft
bearing wear limit was reached, replace it.

© 46337-0

Fig. 588

Disassembly of the camshaft bearings

1. m Insert the pin (1).
m Fit the guide (2).
m Fit the counterhead (3).

2 1

© 45259-0

Fig. 589
2. m Fit the thrust cap (1).
m Screw in nut (2);

© 45266-1

Fig. 590

30-131
 Method of intervention
3. m Hold the threaded shaft (1)
m Tighten nut (2).
NOTE
Tighten the nut further until the bearing bush falls out.

m Remove the bearing shell.

m Remove the installation tool.

2
1

© 46338-0

Fig. 591

Assembly of the camshaft bearings

1. NOTE
Mark the position of the lubrication oil orifice.

© 45268-0

Fig. 592
2. m Check the alignment of the lubricant oil holes (1).

© 45269-0

Fig. 593

30-132
Method of intervention
3. m Insert the pin (1).
m Fit the counterhead (2).
m Fit the new bearing shell on the thrust cap.
WARNING
3
2 1
Ensure that the lubrication oil orifices are aligned correctly.

m Fit the thrust cap (3).

© 45267-1

Fig. 594
4. m Use the installation tool to install the bearing shell flush with the
surface.
NOTE
Press the bearing shell into the crankcase using the
thrust cap.

© 46338-1

Fig. 595
5. m Check the alignment of the lubricant oil holes (1).
NOTE
If the lubricant oil hole is not aligned, assemble and
disassemble the camshaft bearing one more time.

Fig. 596

30-133
 Method of intervention
6. m Assemble the camshaft.
See para. 30.3.37 - Assembly and disassemb... - page 30-139
m Assemble the crankshaft.
See para. 30.3.25 - Assembly and disassemb... - page 30-93

Fig. 597
7. m Push the casing to the support.
m Tighten the screws (2): 9 Nm. 1

NOTE
2
The slot (1) is facing the oil sump.

© 42704-1

Fig. 597
8. m Push the casing to the support.
m Tighten the screws (2): 9 Nm. 1

NOTE
2
The slot (1) is facing the oil sump.

© 42704-1

Fig. 597

30-134
Method of intervention
9. m Push the casing to the support.
m Tighten the screws (2): 9 Nm. 1

NOTE
2
The slot (1) is facing the oil sump.

© 42704-1

Fig. 597

30.3.36 - Disassembly and assembly of the gear case cover

l DEUTZ DW 67 sealant
Disassembly of the gear case cover
1. m Disassemble the starter.
See para. 30.4.8 - Disassembly and assemb... - page 30-251
m Disassemble the connector box.
See para. 30.3.34 - Disassembly and assemb... - page 30-128
m Remove the flywheel.
See para. 30.3.64 - Removal and refitting ... - page 30-232
m Disassemble the speed regulator.
See para. 30.4.2 - Removing and fitting t... - page 30-237

Fig. 598
2. m Remove the oil sump pan.
See para. 30.3.54 - Removing and fitting t... - page 30-199
m Turn the engine on the assembly stand.
m Remove screws (1).
m Remove cover (2).

Fig. 599

30-135
 Method of intervention
3. m Remove screws (1).

1
1

© 46596-0

Fig. 600
4. m Remove screws (1).
m Remove the gear case cover.

1
1
© 46599-0

Fig. 601
5. m Remove crankshaft seal (1).
WARNING 1
Be careful not to damage the mating surfaces when remov-
ing the front cover.

© 42750-0

Fig. 602

30-136
Method of intervention
Assembly of the gear case cover
1. m Clean the mating surfaces.
NOTE
The sealing surfaces must be clean, dry and free of
grease or other contaminants.

m Apply mastic (arrowed).

WARNING
Assembly must be completed within a maximum of 1 hour.

NOTE
Use DEUTZ DW 67 sealant. Sealing edge thickness, ap- © 42525-0

Fig. 603
prox. 1.4 mm.

2. m Align the gear box cover.

m Apply the gear box cover.
NOTE 1

After applying it, do not move the gear box cover.

m Tighten screws (1).

NOTE
Do not tighten the screws at this stage.

1
1
© 46598-0

Fig. 604
3. m Fit the screws.
NOTE
Note that the screws are of different lengths M8 x
45 mm screws (1). M8 x 35 mm screws (2). Do not
tighten the screws at this stage. 1

2
2

© 46596-1

Fig. 605

30-137
 Method of intervention
4. m Push up the gear box cover and align it flush with the sealing surface
of the oil sump (arrows).
NOTE
The oil sump sealing surface in correspondence of
the crankcase must face downwards.

© 46597-0

Fig. 606
5. m Tighten the screws in the sequence indicated: 30 Nm.
5 6 7
4 1
3 2
12 8

13 11

10
14 9

© 36520-3

Fig. 607
6. m Clean the mating surfaces.
NOTE
The mating surfaces must be clean, dry and free of
grease or other contaminants.

m Fit a new O-ring (1).

m Lightly lubricate the O-ring.

© 46460-0

Fig. 608

30-138
Method of intervention
7. m Push the closing cover (2) to the stop.
m Tighten (1) the screws.
NOTE
Use M8 x 45 mm screws: 21 Nm.

m Assemble a new crankshaft O-ring (flywheel side).

See para. 30.3.21 - Replace the crankshaft... - page 30-72

Fig. 609
8. m Assemble the connector box.
See para. 30.3.34 - Disassembly and assemb... - page 30-128
m Fit the flywheel.
See para. 30.3.64 - Removal and refitting ... - page 30-232
m Assemble the speed regulator.
See para. 30.4.2 - Removing and fitting t... - page 30-237
m Assemble the starter.
See para. 30.4.8 - Disassembly and assemb... - page 30-251
m Turn the engine on the assembly stand.
m Fit the oil sump pan.
See para. 30.3.54 - Removing and fitting t... - page 30-199
See para. 30.3.55 - Disassembly and assemb... - page 30-203

Fig. 610

30.3.37 - Assembly and disassembly of the camshaft

Commercially available tools:
l Lifting device
Disassembly of the camshaft
1. m Disassemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163
m Disassemble the injection valves.
See para. 30.3.50 - Fitting and removing i... - page 30-188
m Disassemble the rocker and the support.
See para. 30.3.8 - Removal and refitting ... - page 30-26
m Disassemble the crankshaft.
See para. 30.3.25 - Assembly and disassemb... - page 30-93

Fig. 611

30-139
 Method of intervention
2. m Remove screws (1).
m Hang the crankcase from a suitable workshop crane.

Fig. 612
3. m Disassemble the clamping support (1) from the adapter plates (2).

1
1

2
2

© 42708-0

Fig. 613
4. m Move the assembly stand to the flywheel side.

© 42709-0

Fig. 614

30-140
Method of intervention
5. m Push back all the tappets.
m Carefully remove the camshaft (1) on the flywheel side.

© 42710-0

Fig. 615
6. m Remove all the tappets (arrow).
NOTE
Put the components to one side in the order in which
they were removed. Note the cylinder order.

m Carry out a visual inspection of the components.

© 42711-0

Fig. 616

Assembly of the camshaft

1. m Lightly oil all the tappets.
m Insert all the tappets.
NOTE
Pay attention to couple the tappets.

© 42711-0

Fig. 617

30-141
 Method of intervention
2. m Lightly oil the camshaft bearings.
m Lightly oil the camshaft pins.
m Delicately insert the camshaft.
NOTE
Align the hole (1) in the direction of the cylinder head.

© 42712-0

Fig. 618
3. m Bring closer and orient the assembly stand on the flywheel side.
m Fit the fastener mount (1) onto the adapter plate (2): 90 Nm.

Fig. 619
4. m Hang the crankcase from the workshop crane.
m Remove screws (1).

Fig. 620

30-142
Method of intervention
5. m Assemble the crankshaft.
See para. 30.3.25 - Assembly and disassemb... - page 30-93
m Assemble the rockers and support.
See para. 30.3.8 - Removal and refitting ... - page 30-26
m Assemble the injection valves.
See para. 30.3.50 - Fitting and removing i... - page 30-188
m Assemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163

Fig. 621

30.3.38 - Check the camshaft

Commercially available tools:
l Palmer
l Prisms
Check the camshaft
1. m Disassemble the camshaft.
See para. 30.3.37 - Assembly and disassemb... - page 30-139
m Visually check the wear of the cams and main journal.

Fig. 622
2. NOTE
Measurement diagram of the main journals on points 1 and
2 in surfaces a and b.

Fig. 623

30-143
 Method of intervention
3. m Measure the main journals: 63 (-0.05, -0.07) mm
NOTE
Measurement points, see diagram. If the limit value
has been reached, replace the camshaft.

Fig. 624
4. m Visually check the wear of the camshaft ring gear.
m Assemble the camshaft.
See para. 30.3.37 - Assembly and disassemb... - page 30-139

Fig. 625

30.3.39 - Removal and refitting of the rotation device

Special tools:
l Rotation device: 100320
NOTE
Depending on the number of gear teeth, the rotation tool 100330 may also be used.

Removal
1. m Remove screws (1).
m Remove cover (2).
1

1
© 46419-0

Fig. 626

30-144
Method of intervention
Fitting the rotation device
1. m Insert rotation device (1).
NOTE
2
The toothed wheel of the rotation device must mesh
with the teeth of the camshaft gear.
1
m Tighten screws (2).

2
© 46420-0

Fig. 627

Removal of the rotation device

1. m Remove screws (2).
m Remove rotation device (1).
2

2
© 46420-0

Fig. 628
2. m Clean the mating surfaces of the cover plate and the gearbox cover.
m Fit a new O-ring (1).
m Lightly lubricate the O-ring.

© 46460-0

Fig. 629

30-145
 Method of intervention
3. m Fully press down the cover (3).
m Tighten the screw (2): 30 Nm.
m Tighten the screws (1): 21 Nm. 1

1
© 46419-1

Fig. 630

30.3.40 - Removing and fitting the V-belt pulley

Commercially available tools:
l Torque wrench
l Rotation angle gauge: 8189
l Box spanner insert Torx E20: 8114
Removing the V-belt pulley
1. m Loosen screws (1).
m Remove the V-belt.

Fig. 631
2. m Fit the rotation device.
See para. 30.3.39 - Removal and refitting ... - page 30-144
m Fastening flywheel with rotation tool.
m Unscrew the screws (1) using the box spanner insert.
m Remove the V-belt pulley.

Fig. 632

30-146
Method of intervention
3. m Visually inspect the component.

© 46
Fig. 633

Fitting the V-belt pulley

1. m
NOTE:
Check that bush (1) is present.

© 46
Fig. 634
2. m Fit the V-belt pulley.
NOTE:
The hole (1) must be aligned with the hole (2).

© 46
Fig. 635

30-147
 Method of intervention
3. WARNING
The screws must be renewed after being removed.

NOTE:
Screws: M16 x 1.5

m Tighten the new screws using the socket wrench insert and the rota-
tion angle gauge: 40 Nm + 60° + 60°
m Remove the rotation device.
See para. 30.3.39 - Removal and refitting ... - page 30-144
m Fit the V-belt.
Fig. 636
See para. 30.4.7 - Removal and refitting ... - page 30-247

30.3.41 - Fitting, removing, checking and setting adjuster rod

Commercially available tools:
l Sliding gauge
Special tools:
l Adjustment tool: 100800
Remove the adjuster rod
1. m Disassemble the speed regulator.
See para. 30.4.2 - Removing and fitting t... - page 30-237
m Disassemble the gear case cover.
See para. 30.3.36 - Disassembly and assemb... - page 30-135
m Disassemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163
m Remove screw (1).

Fig. 637
2. m Remove the adjuster rod

Fig. 638

30-148
Method of intervention
3. m Inspect the adjuster rod
m Measure the width of the groove (1): 5 (+0.03,-0.06) mm.

Fig. 639

Fitting the adjuster rod

1. m Fit the adjuster rod

Fig. 640
2. m Fit and tighten the new screw (1): 10 Nm.
WARNING
Self-locking screw!

m Assemble the gear case cover.

See para. 30.3.36 - Disassembly and assemb... - page 30-135

Fig. 641

30-149
 Method of intervention
3. m Lowly push the adjustment rod towards the arrow.
NOTE
Stop position! There must not be irregular resistance.

m Release the adjustment rod.

NOTE
The adjuster rod must be returned to its initial posi-
tion from any other position by spring force. Starting
position!

© 46344-1

Fig. 642

Measuring the travel of the adjuster rod (with injection pumps removed)
1. m Assemble the adjustment device (1).

© 46340-1

Fig. 643
2. m Move the adjustment rod to the stop position.
m Measure the distance between the adjustment rod and the adjust-
ment device.

© 46341-0

Fig. 644

30-150
Method of intervention
3. m Release the adjustment rod.
NOTE
Starting position!

m Measure the distance between the adjustment rod and the adjust-
ment device.
n The difference between the start and stop position indicates

the stroke of the adjustment rod.

Table 62

Calculation example:
Target: Adjustment rod stroke Fig. 645
Data: -
Measured value: Stop position (a), (a) = 30.7 mm.
Start position (b), (b) = 13.4 mm
Calculation: Dimension (a) - dimension (b)
The results of all this are: = 17.3 mm
Nominal dimension = 17.0 mm - 17.5 mm
4. m Rotate the adjustment tool.
m Turn the knurled screw (1) as far as the stop position.
m Assemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163

Fig. 646

30-151
 Method of intervention
Measuring the travel of the adjuster rod (with injection pumps installed)
1. m Assemble the adjustment device (1).

Fig. 647
2. m Move the adjustment rod to the stop position.
m Measure the distance between the adjustment rod and the adjust-
ment device.

Fig. 648
3. m Release the adjustment rod.
NOTE
Starting position!

m Measure the distance between the adjustment rod and the adjust-
ment device.
n The difference between the start and stop position indicates

the stroke of the adjustment rod.

Table 63

Calculation example:
Target: Adjustment rod stroke Fig. 649
Data: -
Measured value: Stop position (a), (a) = 30.5 mm.
Start position (b), (b) = 13.4 mm
Calculation: Dimension (a) - dimension (b)
The results of all this are: = 17.1 mm
Nominal dimension = >16.8 mm

30-152
Method of intervention
4. m Leichtgängigkeit der Regelstange prüfen.
m Lowly push the adjustment rod towards the arrow.
NOTE
There must not be irregular resistance.

m Release the adjustment rod.

NOTE
The adjuster rod must be returned to its initial posi-
tion from any other position by spring force. Starting
position!

Fig. 650

Measuring the residual play of adjuster rod for setting the governor correctly
1. m Measure the residual value between the gearbox and the stop posi-
tion.
WARNING
The value measured must be indicated precisely when re-
placing or repairing the adjuster.

m Assemble the speed regulator.

See para. 30.4.2 - Removing and fitting t... - page 30-237

Fig. 651

30.3.42 - Removal and refitting of the heater

Removal of the heater
1. m Disconnect the wiring connectors.
WARNING 1

Remove the screws, leaving only the positive terminal screw

in place to support the heater.

m Remove screws (1). 1

© 46360-0

Fig. 652

30-153
 Method of intervention
2. m Undo hose union (1).
m Remove seal (2)
m Remove the heater.
m Remove seal (3).

3 2

© 44360-1

Fig. 653
3. m Carry out a visual inspection of the component.

© 44831-0

Fig. 654

Refitting the heater

1. m Fit a new O-ring (3).
m Fit the heater.
m Fit a new O-ring (2).
m Reconnect hose union (1).

3 2

© 44360-1

Fig. 655

30-154
Method of intervention
2. m Tighten screws (1).
m Tighten the screws in alternate sequence: 3 Nm + 30°. 1
m Connect the wiring connector: 20 Nm.
WARNING
Remove the screws, leaving only the positive terminal screw
in place to support the heater. 1

© 46360-0

Fig. 656

30.3.43 - Removal and refitting of the turbocharger

Special tools:
l Disassembly tool: 110901
l DEUTZ S1 assembly product
NOTE
Collect operating materials in suitable containers and dispose of them in compliance with the applicable regulations.
The draining and replenishing of engine fluids and lubricants must be carried out in accordance with the instructions
given in the documentation provided by the manufacturer of the vehicle/appliance.
Removal of the turbocharger
1. m Keep the nut (2).
m Remove screw (1).
2

© 46499-0

Fig. 657
2. m Unscrew hollow screws (1)
m Remove the seals. 1
m Remove lube oil pipe (2).

© 46500-0

Fig. 658

30-155
 Method of intervention
3. m Remove screw (1).
m Remove the support.

© 46501-0

Fig. 659
4. m Remove the oil return pipe (1).

© 46502-0

Fig. 660
5. m Unscrew nuts (1).
m Remove exhaust gas turbocharger (2).
m Remove the gasket.
m Unscrew the stud bolts.
m Carry out a visual inspection of the components. 1 1

2
© 46503-0

Fig. 661

30-156
Method of intervention
Refitting the turbocharger
1. m Clean the mating surfaces.
m Insert the new stud bolts with the assembly product.
m Fit the new stud bolts.
m Fit a new O-ring (1).

© 46504-0

Fig. 662
2. m Fit new O-ring (1).
m Lightly lubricate the O-ring. 1

© 46437-0

Fig. 663
3. m Fit turbocharger (2).
m Tighten the nuts (1): 22 Nm.

1 1

2
© 46503-0

Fig. 664

30-157
 Method of intervention
4. m Fit lube oil pipe (2).
m Fit banjo bolts (1) with new seals, but do not tighten: 18 Nm. 1
m Fit banjo bolts (3) with new seals, but do not tighten: 34 Nm.

© 46500-1

Fig. 665
5. m Fit new O-ring (1).
m Lightly lubricate the O-ring.
1

© 46438-0

Fig. 666
6. m Fit the oil return pipe (2) as indicated by the arrow.

© 46507-0

Fig. 667

30-158
Method of intervention
7. m Insert oil return pipe (1) in the engine block (arrow)
m Fit the mount.
m Tighten the screw (2): 21 Nm.

© 46501-1

Fig. 668
8. m Keep the nut (2).
m Tighten (1) the screw: 13 Nm.
2

© 46499-0

Fig. 669

30.3.44 - Removal and refitting of the charge air duct

l DEUTZ DW 72 mastic
Removal of the charge air duct
1. m Unscrew hollow screws (1)
m Remove the seals.

Fig. 670

30-159
 Method of intervention
2. m Disconnect the wiring connectors.
m Remove screws (1).
m Remove charge air manifold (2).
m Remove the gasket.
m Remove the connector element.

Fig. 671
3. m Remove the cylinder head cover.
See para. 30.3.10 - Disassembly and assemb... - page 30-32
m Remove all the screws (1).
m Remove the charge air duct (2).
m Remove the gaskets.
m Carry out a visual inspection of the component.

Fig. 672

Refitting the charge air duct

1. m Clean the mating surfaces.
m Fit new gaskets (1).
NOTE
Check the installation position is correct.

Fig. 673

30-160
Method of intervention
2. m Fit the charge air duct.

Fig. 674
3. m Fit the screws.
NOTE
Do not disturb the gaskets.

m Tighten the screws: 11 Nm.

NOTE
Tightening sequence Start from centre working out-
wards.

Fig. 675
4. m Fit the cylinder head cover.
See para. 30.3.10 - Disassembly and assemb... - page 30-32
m Clean the mating surfaces.
m Fit the new gasket (1).

Fig. 676

30-161
 Method of intervention
5. m Tighten the new O-rings (1).

Fig. 677
6. m Apply assembly product to connection fitting (1).
m Install the connection fitting (1).

© 46498-0

Fig. 678
7. m Fit the charge air duct.
m Fit screws (1) using thread locking agent.
m Fit screws (2) using thread locking agent.
3
m Fit the screws.
NOTE
Note that the screws are of different lengths M8 x 30
mm (1). M8 x 95 mm (2). M8 x 80 mm (3). 2

m Tighten the screws: 30 Nm.

m Reconnect the wiring connector
1

© 46491-1

Fig. 679

30-162
Method of intervention
8. m Tighten the hollow screw (1): 18 Nm.
NOTE
Use new seals.

© 46490-0

Fig. 680

30.3.45 - Fitting and removing injection pump

1. Commercially available tools:
m Socket wrench insert, 10 mm, twelve-sided
m Toothed insert for socket wrench 8117
m Rotation angle gauge: 8190

Special tools:
m Rotation device: 100320
m Presser tool: 100830
m Special pliers: 103220
m Extractor: 110030
m Special wrench: 110500
m Slide hammer extractor: 150800
m Plugs and caps: 170160

m DEUTZ AP1908 assembly product

WARNING
During work on the fuel system always maintain conditions of the maximum cleanliness.
Before proceeding with removal, remove any paint residue or debris. Thoroughly clean the area around the
components to be worked on. Dry any wet areas with a compressed air jet.
When handling fuel observe the safety directives and specific local regulations. All fuel lines and unions should
be closed immediately after opening using new, clean plugs or caps. Remove plugs and caps only immediately
prior to assembly. Collect auxiliary materials in suitable containers and dispose of them in compliance with the
applicable regulations.
NOTE
If replacing the injection pump, remeasure the thickness of the shim. The EP code must be changed on the
factory plate. In the event of replacement of the crankcase, camshaft or roller tappets, determine the correct
assembly measurement of the injection pump “EK” and the relative part number EP, and modify accordingly
on the identification plate.

30-163
 Method of intervention
Disassembly of the injection pump
1. m Remove the hollow connector from the engine block.
m Disassemble the cylinder head case (1).
See para. 30.3.10 - Disassembly and assemb... - page 30-32

Fig. 681
2. m Remove screws (1).

Fig. 682
3. m Withdraw the engine block (1).

Fig. 683

30-164
Method of intervention
4. m Fit the presser tool (1).

© 46365-0

Fig. 684
5. m Tighten (1) the screws.

© 46372-0

Fig. 685
6. m Turn the knurled screw (1).
NOTE
Turn the knurled screw until it stops (adjuster rod end 1

stop)

© 46373-0

Fig. 686

30-165
 Method of intervention
7. m Remove screws (1).
m Remove cover (2).
1

1
© 46419-0

Fig. 687
8. m Insert rotation device (1).
NOTE
2
The toothed wheel of the rotation device must mesh
with the teeth of the camshaft gear.
1
m Tighten screws (2).

2
© 00000-0

Fig. 688
9. m Turn the crankshaft in the correct direction of rotation of the engine
to align the injector pump actuator cam for the respective cylinder
with the base disc.
Example:
The intake valve of cylinder 1 is open.

© 35356-1

Fig. 689

30-166
Method of intervention
10. m Remove the injection pipe with a special wrench.

© 46424-1

Fig. 690
11. m Remove screws (1).

© 46425-0

Fig. 691
12. m Remove the flange

© 46426-0

Fig. 692

30-167
 Method of intervention
13. NOTE
If the injection pump is seized:

1
m Assemble the slide hammer extractor (1) and extractor (2).
m Tighten the check nut (3).
2

© 40958-0

Fig. 693
14. m Fit the slide hammer extractor onto the injection pump.
m Screw the sleeve nuts (1).
m Remove the seized injection pump.

© 46427-0

Fig. 694
15. m Remove the injection pump.
m Carry out a visual inspection of the component.

© 46418-0

Fig. 695

30-168
Method of intervention
16. m Withdraw roller tappet (1) using the special pliers
m Remove the shim washer.
m Carry out a visual inspection of the components.

Fig. 696

Assembly of the injection pump

1. NOTE
If replacing the injection pump, remeasure the thickness
of the shim. The EP code must be changed on the factory
plate.
m Calculating the thickness of the shim washer (engine without vari-
able injection timing adjuster).
[LNK]
[LNK]
m Calculating the thickness of the shim washer (engine with variable
injection timing adjuster).
[LNK]
[LNK]
m Insert the roller tappet (1) using the special pliers.
NOTE Fig. 697

In the event of replacement of the crankcase, cam-

shaft or roller tappets, determine the correct assem-
bly measurement of the injection pump “EK” and the
relative part number EP, and modify accordingly on
the identification plate.
m Determination of the overall dimensions of the injection pump (en-
gine without the injection advance variator)
[LNK]
[LNK]
m Determination of the overall dimensions of the injection pump (en-
gine with the injection advance variator)
[LNK]
[LNK]

30-169
 Method of intervention
2. m Fit the new O-rings (1).

© 39865-1

Fig. 698
3. m Rotate the injection pump actuator arm into approximately the cen-
tral position.

© 46369-0

Fig. 699
4. m Apply assembly sealant to the seat hole in the crankcase and to the
injection pump O-ring.
m Place the roller tappet for the respective cylinder on the base disc.
m Assemble the injection pump.
m Connect the injection pump actuator arm (1) to the adjuster rod.

© 46418-1

Fig. 700

30-170
Method of intervention
5. m Fit the flange.
NOTE
The bevelled side must face towards the injection
pump body.

© 46426-0

Fig. 701
6. NOTE
Start each time with the screw (2).

m Lightly oil screws (2).

m Lightly oil screws (1).
m Tighten the screws evenly with the socket wrench insert. 5 Nm +
80°.
WARNING 1 2

The flange must sit evenly against the respective surface.

© 46430-0

Fig. 702
7. m Turn all the screws (1) by 190° in the direction indicated by the ar-
row.

1 1

© 46366-0

Fig. 703

30-171
 Method of intervention
8. m Using the toothed socket wrench insert, carefully rotate the injection
pump in the direction indicated by the arrow until it stops.

© 46429-0

Fig. 704
9. NOTE
Start each time with the screw (2).

m Tighten screws (1) and (2). 5 Nm + 150°.

m Fasten the new injection pipes with the special wrench: 25 Nm.

1 2

© 46430-0

Fig. 705
10. m Remove screws (1).
m Remove the presser tool (2).

© 46372-1

Fig. 706

30-172
Method of intervention
11. m Remove screws (2).
m Remove rotation device (1).
2

2
© 00000-0

Fig. 707
12. m Clean the mating surfaces of the cover plate and the gearbox cover.
m Fit a new O-ring (1).
m Lightly lubricate the O-ring.

© 46460-0

Fig. 708
13. m Fully press down the cover (3).
m Tighten the screw (2): 30 Nm.
m Tighten the screws (1): 21 Nm. 1

1
© 46419-1

Fig. 709

30-173
 Method of intervention
14. WARNING
Check the mobility of the adjustment rod.

m Operate the stop lever between the start and stop position.
m Fit a new O-ring (1).
m Lightly lubricate the O-ring.

© 46417-0

Fig. 710
15. m Press and hold down the adjustment rod in the stop position, using
the stop lever.
m Insert the engine block (1).
1

© 46364-0

Fig. 711
16. m Tighten the screws (1): 21 Nm.

© 46371-0

Fig. 712

30-174
Method of intervention
17. m Fit the cylinder head cover (1).
See para. 30.3.10 - Disassembly and assemb... - page 30-32
m Fit the hollow connector on the engine block.

Fig. 713

30.3.46 - Determine the thickness of the shim (engine without injection advance variator)
1. Commercially available tools:
m Torque wrench

NOTE
Let the engine cool down for at least one hour. Lubricant oil temperature < 40 °C. In order to exclude measure-
ment errors, all the support and measurement surfaces must be completely clean!

2. NOTE
The following description, by way of an example, makes
reference to an injection pump. If carrying out the work
procedure on another injection pump, proceed in the same
manner.
m Disassemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163

Fig. 714
3. m Read the EP code on the factory plate for the corresponding cylin-
der. Example: P/N EP 295 for cylinder 1 (1).
m Read and write down the correct assembly dimension for the EK
injection pump based on the EP code. Example: EK = 120.875 mm.
NOTE
Table 3 - see the technical specifications

Fig. 715

30-175
 Method of intervention
4. m Read the code for the (new) injection pump for the length of the in-
jection pump (dimension A). Example: Measurement A = 42.
m Write down dimension A in order to calculate the theoretical thick-
ness of the TS shim.
m Read and write down the base dimension L0 of the injection pump.
Example: 117.5 mm.
NOTE
Table 1 - see the technical specifications

m Calculate the thickness of the shim.

NOTE
Tables 1, 2, 3 - see the technical specifications
Fig. 716

Table 64

Calculation example:
Target: Theoretical thickness of shim wash-
er TS
Effective thickness of shim washer
SS
Data: Injection pump length code A. Base
size of injection pump L0 from table
1, e.g. 117.15 mm. EP part number
(from factory identification plate)
e.g. 295. Correct assembly mea-
surement of injection pump EK from
table according to EP part number,
e.g. 120.875 mm
Calculation: TS = EK - (L0 + A/100), TS =
120.875 mm - (117.5 mm + 42/100
mm), TS = 120.875 mm - 117.92 mm
The results of all this are: TS= 2.955 mm. Select SS referring
to table 2, SS = 3.0 mm.
5. m Place the calculated shim on the roller tappet.
m Assemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163

Fig. 717

30-176
Method of intervention
30.3.47 - Determine the thickness of the shim (engine with injection advance variator)
1. NOTE
Let the engine cool down for at least one hour. Lubricant oil temperature < 40 °C. In order to exclude measure-
ment errors, all the support and measurement surfaces must be completely clean!

2. NOTE
The following description, by way of an example, makes
reference to an injection pump. If carrying out the work
procedure on another injection pump, proceed in the same
manner.
m Disassemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163

Fig. 718
3. m Read the EP code on the factory plate for the corresponding cylin-
der. Example: P/N EP 670 for cylinder 1 (1).
m Read and write down the correct assembly dimension for the EK
injection pump based on the EP code. Example: EK = 117.65 mm.
NOTE
Table 3.1 - see the technical specifications

Fig. 719

30-177
 Method of intervention
4. m Read the code for the (new) injection pump for the length of the in-
jection pump (dimension A). Example: Measurement A = 23.
m Write down dimension A in order to calculate the theoretical thick-
ness of the TS shim.
m Read and write down the base dimension L0 of the injection pump.
Example: 111.15 mm.
NOTE
Table 1.1 - see the technical specifications

m Calculate the thickness of the shim.

NOTE
Tables 1.1, 2.1, 3.1 - see the technical specifications
Fig. 720

Table 65

Calculation example:
Target: Theoretical thickness of shim wash-
er TS Effective thickness of shim
washer SS
Data: Injection pump length code A. Base
size of injection pump L0 from table
1.1, e.g. 111.15 mm. EP part num-
ber (from factory identification plate)
e.g. 670. Correct assembly mea-
surement of injection pump EK from
table according to EP part number,
e.g. 117.65 mm
Calculation: TS = EK - (L0 + A/100). TS = 117.65
mm - (111.15 mm + 23/100 mm). TS
= 117.65 mm - 111.38 mm
The results of all this are: TS= 6.27 mm. Select SS referring to
table 2.1. SS = 6.25 mm.
5. m Place the calculated shim on the roller tappet.
m Assemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163

Fig. 721

30-178
Method of intervention
30.3.48 - Determination of the overall dimensions of the injection pump (engine without
the injection advance variator)
1. Special tools:
m Digital dial gauge: 100410
m Measurement device: 103210

NOTE
Let the engine cool down for at least one hour. Lubricant oil temperature < 40 °C. In order to exclude measure-
ment errors, all the support and measurement surfaces must be completely clean!

2. NOTE
The following description, by way of an example, makes
reference to an injection pump. If carrying out the work
procedure on another injection pump, proceed in the same
manner.
m Disassemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163

Fig. 722
3. NOTE
Residuals of lubricant oil on the roller tappet surface could
falsify the measurement result.

m Clean the roller tappet interface.

m Fit the spacer disc (5 mm) on the roller tappet.
m Insert the roller tappet using the special pliers in the sump of the
injection pump.

Fig. 723
4. m Turn the crankshaft in the engine rotation direction using the rotation
device until the cam for activating the injection pump of cylinder 1 is
located on the base circle position.
NOTE
The intake valve of cylinder 1 is open.

© 35356-1

Fig. 724

30-179
 Method of intervention

30-180
Method of intervention
8. m Insert the dial gauge support in the master group.
m Set the dial gauge with preload to “0”.
NOTE
Pay attention to the unit of measurement. The depth
of the master group measures: Le = 122.25 mm

© 39861-0

Fig. 728
9. m Clean the support and measurement surface on the crankcase.
m Delicately insert the dial gauge support in the injection pump sump.
m Align the dial gauge support.
m Tighten the screws (1) with the spacer bushes (2).
m Tighten the screws (1): 15 Nm.

1 1

2 2
© 46422-0

Fig. 729
10. NOTE
The dial gauge now indicates a value more or less within
the interval.

m Calculate dimension “L”.

Table 66 "L"

Calculation example:
Target: Dimension L
Data: Master group depth Le = 122.25
mm. Spacer disc thickness (d) = 5
mm © 46423-2

Measured value: Dial gauge reading X = + 2.20 mm Fig. 730

Calculation: L = Le - X + d, L = 122.25 mm - 2.20
mm + 5.0 mm
The results of all this are: L=125.05 mm

m Write down dimension “L”.

30-181
 Method of intervention
11. m Disassemble the dial gauge support.
m Calculate the correct assembly dimension of the “EK” injection
pump.
NOTE
Table 1 - see the technical specifications

Table 67

Calculation example:
Target: Correct assembly dimension for the
EK injection pump © 39870-0
Data: Dimension L. Start of delivery (fac- Fig. 731
tory plate). Camshaft type W (from
factory identification plate). Maxi-
mum valve aperture Vh Nominal
value from table 1
Calculation: EK = L - Vh nominal value. EK =
125.05 mm - 5.337 mm
The results of all this are: EK = 119.713 mm

m Write down the correct assembly dimension for the “EK” injection
pump.
12. m Read the code for the injection pump for the length of the injection
pump (dimension A).
m Write down dimension A in order to calculate the theoretical thick-
ness of the TS shim.
n Example: Measurement A = 42.

© 30095-3

Fig. 732
13. m Calculate the thickness of the shim.
NOTE
Tables 1, 2, 3 - see the technical specifications

Table 68

Calculation example:
Target: Theoretic thickness of the TS shim. Thickness of the SS shim
Data: Correct assembly dimension for the EK injection pump (recal-
culated, see calculation above). Injection pump length code A.
Base size of injection pump L0 from table 1, e.g. 117.15 mm.
Calculation: TS = EK - (L0 + A/100). TS = 119.713 mm - (117.5 mm +
42/100 mm). TS = 119.713 mm - 117.92 mm
The results of all this are: TS= 1.793 mm. Select SS referring to table 2. SS = 1.8 mm.

30-182
Method of intervention
14. m Place the calculated shim on the roller tappet.
m Assemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163
NOTE
Perform the measurement for each injection pump.
If replacing the crankcase, camshaft or roller tap-
pet, for the correct assembly dimension of the “EK”
injection pump, determine the relative EP code and
change it on the data plate.
m Determine the EP code.
NOTE
Table 3 - see the technical specifications
Fig. 733

Table 69

Calculation example:
Target: EP code
Data: Correct assembly dimension for
the EK injection pump (recalcu-
lated, see calculation above). EK =
119.713 mm. EK rounded equally =
119.725 mm
Calculation: Select EP part number referring to
table 3
The results of all this are: EP P/N = 249

30.3.49 - Determination of the overall dimensions of the injection pump (engine with the
injection advance variator)
1. Commercially available tools:
m Torque wrench

Special tools:
m Rotation device: 100320
m Digital dial gauge: 100410
m Measurement device: 103210

NOTE
Let the engine cool down for at least one hour. Lubricant oil temperature < 40 °C. In order to exclude measure-
ment errors, all the support and measurement surfaces must be completely clean!

2. NOTE
The following description, by way of an example, makes
reference to an injection pump. If carrying out the work
procedure on another injection pump, proceed in the same
manner.
m Disassemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163

Fig. 734

30-183
 Method of intervention

30-184
Method of intervention
6. m Insert the dial gauge into the relative support.
m Tighten the knurled screw on the dial gauge support.

© 39859-0

Fig. 738
7. m Insert the spacer using the special pliers in the master group.

© 39860-0

Fig. 739
8. m Insert the dial gauge support in the master group.
m Set the dial gauge with preload to “0”.
NOTE
Pay attention to the unit of measurement. The depth
of the master group measures: Le = 122.25 mm

© 39861-0

Fig. 740

30-185
 Method of intervention
9. m Clean the support and measurement surface on the crankcase.
m Delicately insert the dial gauge support in the injection pump sump.
m Align the dial gauge support.
m Tighten the screws (1) with the spacer bushes (2).
m Tighten the screws (1): 15 Nm.

1 1

2 2
© 46422-0

Fig. 741
10. NOTE
The dial gauge now indicates a value more or less within
the interval. Add 1 mm to the stroke of the variable injection
timing adjuster actuator piston (see example calculation).
m Calculate dimension “L”.
Table 70 "L"

Calculation example:
Target: Dimension L
Data: Master group depth Le = 122.25
mm. Actuator piston stroke = + 1 mm
Measured value: Dial gauge reading X = + 0.45 mm © 46423-2

Calculation: L = (Le + 1 mm) - X. L = (122.25 mm Fig. 742

+ 1 mm) - (+ 0.45 mm). L = 123.25
mm - 0.45 mm
The results of all this are: L=122.80 mm

m Write down dimension “L”.

30-186
Method of intervention
11. m Disassemble the dial gauge support.
m Calculate the correct assembly dimension of the “EK” injection
pump.
NOTE
Table 1 - see the technical specifications

Table 71

Calculation example:
Target: Correct assembly dimension for the
EK injection pump © 39870-0
Data: Dimension L. Start of delivery (fac- Fig. 743
tory plate).
Camshaft type W. Maximum valve
aperture Vh Nominal value from
table 1.1
Calculation: EK = L - Vh nominal value. EK =
122.80 mm - 5.337 mm
The results of all this are: EK = 117.463 mm

m Write down the correct assembly dimension for the “EK” injection
pump.
12. m Read the code for the injection pump for the length of the injection
pump (dimension A).
m Write down dimension A in order to calculate the theoretical thick-
ness of the TS shim.
n Example: Measurement A = 23.

23

© 39865-0

Fig. 744
13. m Calculate the thickness of the shim.
NOTE
Tables 1.1, 2.1, 3.1 - see the technical specifications

Table 72

Calculation example:
Target: Theoretic thickness of the TS shim. Thickness of the SS shim
Data: Correct assembly dimension for the EK injection pump (recal-
culated, see calculation above). Injection pump length code A.
Base size of injection pump L0 from table 1.1, e.g. 111.15 mm.
Calculation: TS = EK - (L0 + A/100). TS = 117.463 mm - (111.15 mm +
23/100 mm). TS = 117.463 mm - 111.38 mm
The results of all this are: TS= 6.083 mm. Select SS referring to table 2.1 SS = 6.1 mm.

30-187
 Method of intervention
14. m Place the calculated shim on the roller tappet.
m Assemble the injection pump.
See para. 30.3.45 - Fitting and removing i... - page 30-163
NOTE
Perform the measurement for each injection pump.
If replacing the crankcase, camshaft or roller tap-
pet, for the correct assembly dimension of the “EK”
injection pump, determine the relative EP code and
change it on the data plate.
m Determine the EP code.
NOTE
Table 3.1 - see the technical specifications
Fig. 745

Table 73

Calculation example:
Target: EP code
Data: Correct assembly dimension for
the EK injection pump (recalcu-
lated, see calculation above). EK =
117.463 mm. EK rounded equally =
117.475 mm
Calculation: Select EP part number referring to
table 3.1
The results of all this are: EP P/N = 663

30.3.50 - Fitting and removing injection valves

Special tools:
l Extractor: 110030
l Extraction device: 120660
l Special wrench: 110500
l Slide hammer extractor: 150800
l DEUTZ AP1908 assembly product
DANGER
After switching off the engine, wait at least 30 seconds before carrying out any work on the fuel system!

WARNING
During work on the fuel system always maintain conditions of the maximum cleanliness.
Thoroughly clean the area around the components to be worked on. Dry any wet areas with a compressed air jet.
When handling fuel observe the safety directives and specific local regulations.
All lines and unions should be closed immediately after opening using new, clean plugs or caps. Remove plugs and
caps only immediately prior to assembly. Collect operating materials in suitable containers and dispose of them in
compliance with the applicable regulations.
NOTE
The following operating procedure is for the installation and removal of a single injection valve. Repeat the procedure
as necessary if more injection valves must be removed.

30-188
Method of intervention
Disassembly of the injection valve
1. m Remove the cylinder head cover.
See para. 30.3.10 - Disassembly and assemb... - page 30-32
m Unscrew the sleeve nuts (1) using the special wrench.

Fig. 746
2. m Unscrew the sleeve nuts (1) using the special wrench.
m Remove the injection pipe.
m Remove the rubber seal from the injection pipe.

© 46570-0

Fig. 747
3. m Remove screw (1).
m Remove retaining bracket (2).
m Remove the injection valve (3).

© 46571-0

Fig. 748

30-189
 Method of intervention
Disassembly of the blocked injection valve
1. m Assemble the slide hammer extractor (1) and extractor (2).
m Tighten the check nut (3).

© 46571-0

Fig. 749
2. m Fit the slide hammer extractor on the injection valve.
m Screw the sleeve nuts (1).
m Withdraw the blocked injection valve.
m Remove the O-ring fastened into the cylinder head with an extractor
tool.

Fig. 750
3. m Carry out a visual inspection of the components.
m Check the injection valve.
See para. 30.3.51 - Checking the injection... - page 30-192

Fig. 751

30-190
Method of intervention
Assembly of the injection valve
1. m Fit a new O-ring (1).
m Fit a new O-ring (2).

Fig. 752
2. WARNING
Observe the installation position. The flange (1) of the injec-
tion valve must face away from the fastener bracket.

Fig. 753
3. m Fit the injection valve (3).
m Fit retaining bracket (2).
m Tighten (1) the screw: 16 Nm.

Fig. 754

30-191
 Method of intervention
4. m Fit a new injection pipe (1).
m Fasten the sleeve nuts (2) with the special wrench: 25 Nm.
m Fit the rubber seal (3).
m Fit the cylinder head cover.
See para. 30.3.10 - Disassembly and assemb... - page 30-32

Fig. 755

30.3.51 - Checking the injection valves

1. Commercially available tools:
m Box spanner insert SW15: 8012
m Injector control equipment: 8008

Special tools:
m Support: 110110

DANGER
Risk of accident when handling the nozzle tester. The injector jet causes the fuel to penetrate deep under the
skin! Risk of septicaemia!

NOTE
After operating the manual lever three or four times, the spring chamber fills with diesel fuel/test oil to above the
injection valve needle. Afterwards, it is not possible to operate the manual lever. Before every test procedure,
carefully loosen the nozzle fastener nut to release pressure from the spring chamber. To check the injection
valves, use only pure ISO 4113 standard test oil or clean diesel fuel.
2. m Disassemble the injection valves.
See para. 30.3.50 - Fitting and removing i... - page 30-188

Fig. 756

30-192
Method of intervention
Assembly of the injection valve on the injector tester
1. m Insert the injection valve in the support.
m Loosen the nozzle tightening nut by approx. 180° using the box
spanner insert (pressure reduction) and then retighten it: 35 Nm.

© 36271-2

Fig. 757
2. m Fit the injection valve on the injector tester.

© 35889-2

Fig. 758

Check the opening pressure

1. m Slightly push the injector tester lever down with the pressure gauge
inserted.
m Read the value measured.
NOTE
The pressure at which the pointer stops or goes
down suddenly is the opening pressure. Repeat the
check 3 times.

© 36293-2

Fig. 759

30-193
 Method of intervention
2. m Compare the values measured: 220 bar.
NOTE
The measurement values of the three tests must co-
incide with the control value.

m Replace the injection valve if the value measured deviates from the
specified value.

© 36293-2

Fig. 760

Check the air-tightness

1. m Dry the injectors and injector holders with a jet of air.
m Press down lightly on the manual tester lever until arriving at approx.
20 bar below the opening pressure read previously.

© 36293-2

Fig. 761
2. NOTE
The injector is air sealed if it does not drip within 10 seconds.

© 36294-2

Fig. 762

30-194
Method of intervention
3. m Replace the injection valve if fuel drips from the injector.
WARNING
Retouch work is not permitted!

© 36295-2

Fig. 763

Checking the mobility of the jet needle

1. m Turn off the tester pressure gauge.
m Perform the noise and needle jet test.
NOTE
Check the mobility of the jet needle in the body of the
injector by means of an acoustic noise test. Due to
the increasing wear in the seat of the injection valve
needle, the acoustic behaviour of the injectors will
change. Quickly operating the lever of a worn injec-
tion valve emits a sound that can be heard and the
fuel is finely pulverised. The jet is quite different than
that from a new injection valve.

© 36296-2

Fig. 764
2. m Replace the injection valve if the injector makes no audible sound.

© 36296-2

Fig. 765

30-195
 Method of intervention
Disassembly of the injection valve from the injector tester
1. m Loosen the nozzle tightening nut by approx. 180° using the box
spanner insert (pressure reduction) and then retighten it: 35 Nm.
NOTE
Before installing the injection valves, reduce the pressure in
the spring chamber.

m Assemble the injection valves.

See para. 30.3.50 - Fitting and removing i... - page 30-188

Fig. 766

30.3.52 - Removal and refitting of the fuel lift pump

Special tools:
l Plugs and caps: 170160
DANGER
After switching off the engine, wait at least 30 seconds before carrying out any work on the fuel system!

WARNING
If working on the fuel system, make sure it is completely clean. From time to time, carefully clean the area surrounding
the concerned component . Dry any wet areas with compressed air. When handling fuel observe the safety directives
and specific local regulations. After opening, immediately close all the connections with new and clean plugs/caps.
Remove plugs/caps only immediately prior to assembly. Collect the exiting technical fluids in suitable containers and
dispose of them in accordance with current regulations. Only check/re-tension/change the V-belt while the engine is
stationary.
Removal of the fuel lift pump
1. DANGER
After switching off the engine, wait at least 30 seconds be-
fore carrying out any work on the fuel system!

m Unscrew banjo bolt (1)

NOTE
Collect any leaked fuel and dispose of it properly.

Fig. 767

30-196
Method of intervention
2. m Remove screws (1).
m Remove the fuel lift pump.
1
m Remove the V-belt.
m Carry out a visual inspection of the components.

© 46573-0

Fig. 768

Refitting the fuel lift pump

1. m Fit the fuel lift pump.
m Tighten screws (1).

© 46574-0

Fig. 769
2. m Fit the V-belt.
m Using a suitable tool, push bracket (1) in the direction of the arrow.

© 46375-1

Fig. 770

30-197
 Method of intervention
3. m Preload the screws (1).
m Check the V-belt tension.
See para. 30.4.7 - Removal and refitting ... - page 30-247

Fig. 771
4. m Tighten the hollow screw (1): 39 Nm (M12x1.5).
NOTE
Use new seals. Bleed the fuel system as indicated in
the instruction manual, using the hand pump on the
fuel pre-filter.

Fig. 772

30.3.53 - Removal and refitting of the oil pickup pipe

Removal of the oil pickup pipe
1. m Remove the oil sump pan.
See para. 30.3.54 - Removing and fitting t... - page 30-199
See para. 30.3.55 - Disassembly and assemb... - page 30-203
m Remove screws (1).
m Remove oil pickup pipe (2).
m Remove the gasket.
m Carry out a visual inspection of the components.

Fig. 773

30-198
Method of intervention
Refitting the oil pickup pipe
1. m Clean the mating surfaces.
m Fit a new gasket.
m Fit the oil pickup pipe.
m Fit the screws.
NOTE
Observe the installation position. Note that the
screws are of different lengths M8 x 25 mm (1).
M8 x 16 mm (2)

Fig. 774
2. m Tighten the screws (1): 21 Nm.
m Fit the oil sump pan.
See para. 30.3.54 - Removing and fitting t... - page 30-199
See para. 30.3.55 - Disassembly and assemb... - page 30-203

Fig. 775

30.3.54 - Removing and fitting the lubricant oil sump pan (cast iron lubricant oil sump)
l DEUTZ DW 74 sealant
NOTE
Collect operating materials in suitable containers and dispose of them in compliance with the applicable regulations.
The draining and replenishing of engine fluids and lubricants must be carried out in accordance with the instructions
given in the documentation provided by the manufacturer of the vehicle/appliance.
Removal of the oil sump pan.
1. m Do not fully unscrew drain plug (1).
m Remove the seal.
m Drain, collect and dispose of used oil in accordance with the appli-
cable regulations.

© 46593-0

Fig. 776

30-199
 Method of intervention
2. m Remove screws (1).
m Remove the washer.
m Remove oil filler neck (2).
m Remove the gasket.

1
© 46592-0

Fig. 777
3. m Remove all the screws (1).
m Remove the sump pan. 1

© 46594-3

Fig. 778
4. m Carry out a visual inspection of the components.

© 44948-0

Fig. 779

30-200
Method of intervention
Refitting the oil sump pan.
1. m Clean the mating surfaces.
NOTE
The mating surfaces must be free of grease and dirt.

m Apply sealant evenly to the sealing surface.

NOTE
Apply the sealant in a bead approx. 3.5 mm thick.
The illustration shows only a detail of where the seal-
ant is to be applied.

© 43451-0

Fig. 780
2. m Fit the oil sump pan.
1
NOTE
Be careful not to dislodge the sealant when fitting the
oil sump pan.
2
m Fit the screws.
Screw length:
2
M8 x 130 mm (1). M8 x 110 mm (2).

1
© 46594-2

Fig. 781
3. m Screw in all the screws (1).
1
Screw length:
M8 x 35 mm

© 46594-3

Fig. 782

30-201
 Method of intervention
4. m Orient the oil sump pan on the crankcase.

© 44951-0

Fig. 783
5. m Tighten the screws in the sequence indicated.
20 18 12
NOTE 22
8
21 4
See figure for the correct tightening sequence: 30 19
1
5
Nm 9
13

11

7 15
3 17
2 14 16
6
10

© 45133-0

Fig. 784
6. m Clean the mating surfaces.
m Fit a new seal.
m Fit oil filler neck (1).
m Tighten screws (3).
m Fit the washer.
m Tighten screws (2).
m Tighten the screw (3): 30 Nm.
1
m Tighten the screw (2): 30 Nm.

3
© 46592-1

Fig. 785

30-202
Method of intervention
7. m Fit a new seal.
m Tighten the screw plug (1): 55 Nm (M18 x 1.5).
m Top up the engine oil following the instructions provided.

© 46593-0

Fig. 786

30.3.55 - Disassembly and assembly of the lubricant oil sump (lubricant oil sump-plate)
Commercially available tools:
l Wire brush
l Four M8 x 70 stud bolts
Special tools:
l Tool for truncation: 151500
l DEUTZ DW 74 sealant
WARNING
Make sure that no sealant residue enters the engine crankcase! Close all holes.

NOTE
Collect operating materials in suitable containers and dispose of them in compliance with the applicable regulations.
The draining and replenishing of engine fluids and lubricants must be carried out in accordance with the instructions
given in the documentation provided by the manufacturer of the vehicle/appliance.
Removal of the oil sump pan.
1. m Do not fully unscrew drain plug (1).
m Remove the seal.
m Drain, collect and dispose of used oil in accordance with the appli-
cable regulations.

© 44480-0

Fig. 787

30-203
 Method of intervention
2. m Remove all the screws (1).

© 45971-0

Fig. 788
3. m Insert lever (1) up to shoulder (2).
WARNING
The lever may only be used on the engine crankcase. Do
not use it to apply leverage on aluminium castings. Do not 2

damage the mating surfaces.

© 45969-0

Fig. 789
4. m Insert the second lever (1) up to shoulder (2).
WARNING
The lever may only be used on the engine crankcase. Do
2
not use it to apply leverage on aluminium castings. Do not
damage the mating surfaces. 1

© 45970-0

Fig. 790

30-204
Method of intervention
5. m Prise the sump pan off the crankcase.
m Remove the sump pan.

© 45968-0

Fig. 791
6. m Carry out a visual inspection of the component.

© 43450-1

Fig. 792

Refitting the oil sump pan.

1. m Remove the old sealant using the lever.

© 45973-0

Fig. 793

30-205
 Method of intervention
2. WARNING
Wear eye protection.

m Clean the mating surfaces with a wire brush.

NOTE
The mating surfaces must be clean, dry and free of
grease or other contaminants.

© 45967-1

Fig. 794
3. WARNING
Wear eye protection.

m Clean the mating surfaces with a wire brush.

NOTE
The mating surfaces must be clean, dry and free of
grease or other contaminants.

© 45972-0

Fig. 795
4. m Apply an even bead of sealant to the mating surfaces and the ribs
of the oil sump pan.
NOTE
Apply the sealant in a bead approx. 3.5 mm thick.
The illustration shows only a detail of where the seal-
ant is to be applied.

© 43451-0

Fig. 796

30-206
Method of intervention
5. m To align the oil sump pan with crankcase, screw four stud bolts (1)
into the crankcase as shown. 1
m Line the oil sump pan up using the stud bolts as guides.
m Fit the oil sump pan.
WARNING
Allow the time specified for the sealant to set, taking care
not to move the lubricant oil sump pan.

m Unscrew the stud bolts.

© 45678-0

Fig. 797
6. m Screw in all the screws (1).
NOTE
Note that the screws are of different lengths

© 45971-0

Fig. 798
7. m Tighten the screws in the sequence indicated: 30 Nm.
NOTE
24 20 16 12 8 4 1 5 9 13 17 21 25 29
Representation: 6 cylinder tightening sequence

28 32
31 34
27 33

23 19 15 11 7 3 2 6 10 14 18 22 26 30

© 43414-0

Fig. 799

30-207
 Method of intervention
8. NOTE
Representation: 4 cylinder tightening sequence
20 16 12 8 4 1 5 9 13 17

24 21

26 25

23 22

19 15 11 7 3 2 6 10 14 18

© 43413-0

Fig. 800
9. m Fit a new seal.
m Tighten the screw plug (1): 55 Nm (M18x1.5).
m Top up the engine oil following the instructions provided.

© 44480-0

Fig. 801

30.3.56 - Removal and refitting of the oil cooler

l DEUTZ AP1908 assembly product
NOTE
Collect operating materials in suitable containers and dispose of them in compliance with the applicable regulations.
The draining and replenishing of engine fluids and lubricants must be carried out in accordance with the instructions
given in the documentation provided by the manufacturer of the vehicle/appliance.
Removal of the oil cooler
1. m Remove the oil cooler housing.
See para. 30.3.57 - Disassembly and assemb... - page 30-211

Fig. 802

30-208
Method of intervention
2. m Remove the retainer plate (1).

Fig. 803
3. m Remove screws (1).
m Remove the seals.

1
1

© 46511-0

Fig. 804
4. m Remove oil cooler (2)
m Carry out a visual inspection of the components.

© 46512-0

Fig. 805

30-209
 Method of intervention
Refitting the oil cooler
1. m Clean the mating surfaces.
m Apply the assembly product on the O-rings.
m Fit new O-rings (1).
1 1

© 46513-0

Fig. 806
2. m Align the oil radiator.
NOTE
Use new seals.

m Insert the screws.

Fig. 807
3. m Tighten the screws in alternate sequence (1).
m Tighten the screws (1): 22 Nm.

Fig. 808

30-210
Method of intervention
4. m Fit the retainer plate (1).
m Assemble the oil radiator housing.
See para. 30.3.57 - Disassembly and assemb... - page 30-211

Fig. 809

30.3.57 - Disassembly and assembly of the oil radiator housing

Commercially available tools:
l Pliers for hose clips: 8011
Special tools:
l Plugs and caps: 170160
l DEUTZ AP1908 assembly product
NOTE
Collect operating materials in suitable containers and dispose of them in compliance with the applicable regulations.
The draining and replenishing of engine fluids and lubricants must be carried out in accordance with the instructions
given in the documentation provided by the manufacturer of the vehicle/appliance.
Disassembly of the oil radiator housing
1. m Disconnect the wiring connectors.

Fig. 810

30-211
 Method of intervention
2. m Do not fully unscrew drain plug (1).
m Empty, collect and dispose of the coolant in compliance with regula-
tions.

Fig. 811
3. m Loosen the hose clips (1).
m Remove the flexible hose (2).

© 46543-0

Fig. 812
4. m Unscrew banjo bolt (1)
m Remove the seals.
m Drain, collect and dispose of used oil in accordance with the appli-
cable regulations.
1

© 46517-0

Fig. 813

30-212
Method of intervention
5. m Remove screws (1).
m Remove fuel filter head (2).

© 46518-0

Fig. 814
6. m Remove screws (1).
m Remove oil radiator body (2). 1 1
m Remove the gasket.

1 2 1

© 46519-0

Fig. 815
7. m Carry out a visual inspection of the component.

© 46534-0

Fig. 816

30-213
 Method of intervention
Assembly of the oil radiator housing
1. m Clean the mating surfaces.
m Fit a new O-ring

© 46521-0

Fig. 817
2. m Fit the oil radiator housing.
m Fit the screws.
3 2
NOTE 1

Note that the screws are of different lengths M8 x 55

mm (1). M8 x 90 mm (2). M8 x 110 mm (3)

m Tighten the screws in alternate sequence: 30 Nm.

1
3 1 2

© 46519-1

Fig. 818
3. m Fit the fuel filter head.
m Fit the nut (1).
m Tighten screws (2).
2

© 46522-0

Fig. 819

30-214
Method of intervention
4. m Fit the nut (1).
m Tighten screws (2). 1
m Tighten the screws: 30 Nm.

© 46523-0

Fig. 820
5. m Tighten the hollow screw (1) with the new O-rings: 39 Nm.
WARNING
Route the flexible pipe without friction or tension points.
1

© 46517-0

Fig. 821
6. m Position the hose clips.
m Fit flexible pipe (1).
m Secure the hose clips with the special pliers.

© 46548-0

Fig. 822

30-215
 Method of intervention
7. m Position the hose clips.
m Fit flexible pipe (1).
m Secure the hose clips with the special pliers.

© 46549-0

Fig. 823
8. m Fit a new seal.
m Fit and tighten plug (1).
m Re-connect the wiring connectors
NOTE
Check that the connection is made correctly. Bleed
the fuel system as indicated in the instruction manu-
al, using the hand pump on the fuel pre-filter.

© 46550-0

Fig. 824

30.3.58 - Removal and refitting of the oil pressure switch

Special tools:
l Long socket wrench insert: 110700
l Plugs and caps: 170160
NOTE:
Maximum cleanliness is essential when working on the lubricating oil system.

NOTE:
Thoroughly clean the area around the components to be worked on. Dry any wet areas with a compressed air jet.

NOTE:
When handling lubricating oils, observe safety standards and all applicable local regulations.

NOTE:
All lines and unions should be closed immediately after opening using new, clean plugs or caps.

30-216
Method of intervention
NOTE:
Remove plugs and caps only immediately prior to assembly.

Removal of the oil pressure switch

1. m Unlock and disconnect wiring connectors (1).

Fig. 825
2. m Remove oil pressure switch (1).
NOTE:
Collect used oil and dispose of it in accordance with
the applicable regulations.
1
m Carry out a visual inspection of the components.

© 42866-0

Fig. 826

Fit the oil pressure switch

1. m Fit and tighten the oil pressure switch (1) with a new O-ring: 40 Nm

© 42866-0

Fig. 827

30-217
 Method of intervention
2. m Reconnect wiring connector (1).
NOTE:
Check that the connection is made correctly.

© 42865-1

Fig. 828

30.3.59 - Removal and refitting of the water pump

NOTE:
Collect operating materials in suitable containers and dispose of them in compliance with the applicable regulations.

NOTE:
The draining and replenishing of engine fluids and lubricants must be carried out in accordance with the instructions
given in the documentation provided by the manufacturer of the vehicle/appliance.

Removal of the water pump

1. m Disassemble the fan support.
See para. 30.3.63 - Removal and refitting ... - page 30-230
m Remove the fuel lift pump.
See para. 30.3.52 - Removal and refitting ... - page 30-196
m Remove screws (1).
NOTE:
Collect any leaked coolant and dispose of it in ac-
cordance with regulations.

Fig. 829

30-218
Method of intervention
2. m Carry out a visual inspection of the components.

Fig. 830

Refitting the water pump

1. m
NOTE
The sealing surfaces must be clean, dry and free of
grease or other contaminants.

m Clean the mating surfaces.

© 46577-0

Fig. 831
2. m Fit a new O-ring
m Fit water pump (1).
WARNING 1

Use new coated screws

m Fit the screws.

© 46575-1

Fig. 832

30-219
 Method of intervention
3. m Tighten the screws in the sequence indicated: 30 Nm.
Tightening sequence
n First tighten screw (1) followed by screw (2) and then the 2
remaining screws in any order.

© 46578-0

Fig. 833
4. m Fit the fuel lift pump.
See para. 30.3.52 - Removal and refitting ... - page 30-196
m Assemble the fan support.
See para. 30.3.63 - Removal and refitting ... - page 30-230

Fig. 834

30.3.60 - Testing the thermostat (after removal)

Commercially available tools:
l Thermometer
WARNING
Risk of injury! Hot water and hot thermostat.

Testing the thermostat

1. m Remove the thermostat.
See para. 30.3.61 - Removal and refitting ... - page 30-222
m Measure dimension (a), with thermostat closed.
m Make a note of dimension (a).

Fig. 835

30-220
Method of intervention
2. m Place the thermostat in water and heat the water.
NOTE:
To ensure an accurate reading, measure the temper-
ature as near to the thermostat as possible.

NOTE:
To ensure that the heat is evenly distributed, the wa-
ter should be in constant motion. The temperature
should not increased at a rate of more than 1°C/min.,
otherwise opening of the thermostat will be delayed.
m Determine the temperature at which the thermostat starts to open:
83 °C.
Fig. 836
3. m Measure dimension (b), with thermostat open.
m Make a note of dimension (b).

Fig. 837
4. m Calculate the stroke of the thermostat valve.
Table 74

Calculation example:
Target: Valve stroke
Data: -
Measured value: Stroke start, dimension (a)
Stroke end, dimension (b)
(b) - (a)
The results of all this are: = Valve stroke

m Compare this value with the nominal value.

n Nominal valve lift: minimum 8 mm
Fig. 838
m Fit the thermostat.
See para. 30.3.61 - Removal and refitting ... - page 30-222

30-221
 Method of intervention
30.3.61 - Removal and refitting of the thermostat
Special tools:
l DEUTZ AP1908
NOTE:
Collect operating materials in suitable containers and dispose of them in compliance with the applicable regulations.

NOTE:
The draining and replenishing of engine fluids and lubricants must be carried out in accordance with the instructions
given in the documentation provided by the manufacturer of the vehicle/appliance.

Removal of the thermostat

1. m Remove screws (1).
m z Remove outlet elbow (2).
1

2
1

© 46294-0

Fig. 839
2. m Remove the coolant thermostat (1).
m Carry out a visual inspection of the components.
1

© 46524-0

Fig. 840

30-222
Method of intervention
Refitting the thermostat
1. m Clean the mating surfaces.
m Use a new seal (1). 1
m Apply assembly product to the new seal.

© 44439-0

Fig. 841
2. m Fit the coolant thermostat.

© 46524-1

Fig. 842
3. m Fit the exhaust aperture (2).
m Tighten the screws (1): 30 Nm.
1

2
1

© 46294-0

Fig. 843

30-223
 Method of intervention
30.3.62 - Removal and assembly of the fan support
Commercially available tools:
l 2-arm extractor
l Internal extractor
l Extension for extractor tool
l Circlip pliers
l Press
Special tools:
l Screw: M10 x 40 mm
l Washer
Removal of the fan support
1. m Remove the fan mount
See para. 30.3.63 - Removal and refitting ... - page 30-230
m Remove screw (1).
m Keep the nut (2).

Fig. 844
2. m Tighten the screw (1) by a few turns.

Fig. 845
3. WARNING
Take care not to damage the components

m Remove the toothed belt pulley with the 2-arm extractor.

© 46527-0

Fig. 846

30-224
Method of intervention
4. m Fit the internal extractor (1).
m Open the internal extractor fully to the stop position.

© 46528-0

Fig. 847
5. m Fit the counterhead.

© 46529-0

Fig. 848
6. m Remove the ball bearings and the hollow shaft.

© 46530-0

Fig. 849

30-225
 Method of intervention
7. m Remove circlip (2).

© 46531-0

Fig. 850
8. m Fit the screws (1) and the washer (2).
NOTE:
Screw length: M10 x 40 mm (1)

© 46532-0

Fig. 851
9. m Turn the extension (1) on the screw (2).

© 46547-0

Fig. 852

30-226
Method of intervention
10. m Fit the counterhead.
m z Remove the ball bearings and nuts.

© 46533-0

Fig. 853
11. m z Push out the nuts.

© 46535-0

Fig. 854
12. m Extract the hollow shaft.
m z Visually inspect the components.

© 46536-0

Fig. 855

30-227
 Method of intervention
Completion of the fan drive
1. m Press-fit the hollow shaft into place.

© 46537-0

Fig. 856
2. m Press-fit the nuts.

© 46538-0

Fig. 857
3. NOTE:
The nuts (1) must face downwards.

m Fit the ball bearings.

1

© 46539-0

Fig. 858

30-228
Method of intervention
4. m z Press-fit the ball bearings into the outer ring.

© 46540-0

Fig. 859
5. m Fit circlip (2).
WARNING
Make sure the assembly position is correct.
2

© 46531-0

Fig. 860
6. m Press-fit the ball bearings into the outer ring.

Fig. 861

30-229
 Method of intervention
7. m Fit V-belt pulley (1).
m Screw in the screw (2).

Fig. 862
8. m Keep the nut (2).
m Tighten screw (1).
n Stage 1: 3 Nm
n Stage 2: 124 Nm

m Fit the fan drive.

See para. 30.3.63 - Removal and refitting ... - page 30-230

Fig. 863

30.3.63 - Removal and refitting of the fan support

Assembly product:
l DEUTZ AP1908
NOTE
The draining and replenishing of engine fluids and lubricants must be carried out in accordance with the instructions
given in the documentation provided by the manufacturer of the vehicle/appliance.

Disassembly of the fan support

1. m Remove screws (1).
m Disassemble the fan support.

1
1

© 46551-0

Fig. 864

30-230
Method of intervention
2. m Remove seal (1).
m Remove the connection fitting (2). 1
m Carry out a visual inspection of the components.

© 46552-1

Fig. 865

Assembly of the fan support

1. m Install a new seal (1).
m Apply assembly product to the new seal.

© 46553-0

Fig. 866
2. m Tighten the new O-rings (1).
m Apply the assembly product on the O-rings.

© 46554-1

Fig. 867

30-231
 Method of intervention
3. m Install the connection fitting (1).
1

© 46555-0

Fig. 868
4. m Fit the fan mount.
WARNING
Make sure the assembly position is correct. 1
1

NOTE:
Note that the screws are of different lengths 1

m Tighten screws (1).

m Tighten the screws (1): 60 Nm
© 46551-0

Fig. 869

30.3.64 - Removal and refitting of the flywheel

Commercially available tools:
l Rotation angle gauge: 8190
l Shop-made guide pin
Removal of the flywheel
1. m Remove the closing plugs (1).

© 31115-2

Fig. 870

30-232
Method of intervention
2. m Counterhold the flywheel using a suitable tool.
m Remove screws (1).
m Remove the flywheel.
m Visually inspect the components.
1

© 42825-1

Fig. 871

Refitting the flywheel

1. m Insert the shop-made guide pin
NOTE:
The holes in the flywheel must coincide with the
threaded hole in the V-belt pulley.

© 34224-2

Fig. 872
2. WARNING
The screws must be renewed after being removed.

m Tighten the screws in alternate sequence.

n M10 x 30: 30 Nm + 60° + 30°
n M10 x 35 - M10 x 85: 30 Nm + 60° + 60°

© 42826-0

Fig. 873

30-233
 Method of intervention
3. m Insert the plugs fully into the threaded holes (arrowed).

© 31115-1

Fig. 874

30.3.65 - Replacing the starter motor ring gear on the flywheel

DANGER
Risk of accident, do not touch hot components!

Disassembly of the starter ring gear

1. m Remove the flywheel.
See para. 30.3.64 - Removal and refitting ... - page 30-232
m Perforate the ring gear.
NOTE:
Counterhold the flywheel using a suitable tool.

Fig. 875
2. m Remove the starter ring gear with a suitable tool.

Fig. 876

30-234
Method of intervention
3. m Clean the flywheel.
m Visually inspect the flywheel.

Fig. 877

Assembly of the starter ring gear

1. m Heat the starter ring gear to 220 °C.
m Position the starter ring gear on the flywheel.
NOTE:
The starter ring gear must rest evenly on the flywheel
support flange.

Fig. 878
2. m Fit the flywheel.
See para. 30.3.64 - Removal and refitting ... - page 30-232

Fig. 879

30-235
 Method of intervention
30.4 - C0 - Engine accessories
30.4.1 - Starter motor
REMOVAL
1. DANGER
Disconnect the lead from the battery negative terminal (-) and apply the parking brake.

2. Remove nut (1), detach leads (2) from the starter motor (3) and remove
protection (4).

Fig. 880
3. Remove extension (5), detach cable (6) and remove protection (7).

Fig. 881
4. Remove screw and disconnect cable (8).

Fig. 882
5. Remove the three screws (9) and remove the starter motor (3).

Fig. 883

30-236
Method of intervention
Installation
Install by following the removal steps in reverse order and carry out the following procedures:
Procedure 4
l Screw: 1 to 1.3 Nm (0.74-0.96 lb.ft.)
Procedure 3
l Extension: 16 to 20 Nm (11.76-14.74 lb.ft.)
Procedure 2
l Nut: 16 to 20 Nm (11.76-14.74 lb.ft.)

30.4.2 - Removing and fitting the engine governor

l DEUTZ DW 73 sealant
Removing the engine governor
1. m Disconnect the wiring connectors.
m Unscrew banjo bolt (1)
m Remove the seals.

© 46487-0

Fig. 884
2. m Remove screws (1).
m Remove the engine governor.

1
© 46488-0

Fig. 885

30-237
 Method of intervention
3. m Clean the mating surfaces.
m Carry out a visual inspection of the component.

© 46489-0

Fig. 886

Fitting the engine governor

1. m Apply the sealant evenly on the sealing surfaces of the gear case.
NOTE
The mating surfaces must be clean, dry and free of
grease or other contaminants.

© 46348-1

Fig. 887
2. m Assemble the speed regulator.
m Fit the engine governor.
NOTE 1
If necessary, turn the governor ring gear (1) slightly to
facilitate meshing.

© 46347-1

Fig. 888

30-238
Method of intervention
3. m Tighten the screws in the sequence indicated: 17 Nm.
NOTE
If the governor is replaced with a spare part, the origi- 3 1
nal rod retraction value must be set.

5 2 4

© 46349-0

Fig. 889
4. m Tighten the hollow screw (1): 18 Nm.
NOTE
Use new seals.

m Reconnect the wiring connector

NOTE
Check that the connection is made correctly. 1

© 46487-0

Fig. 890

30.4.3 - Removal and refitting of the exhaust manifold

l DEUTZ S1 assembly product
Removal of the exhaust manifold
1. m Remove the turbocharger.
See para. 30.3.43 - Removal and refitting ... - page 30-155
m Unscrew nuts (1).
m Remove the spacer bushes.
m Remove exhaust manifold (2).

Fig. 891

30-239
 Method of intervention
2. m Remove the gaskets.
m Remove the stud bolts.

Fig. 892
3. m Carry out a visual inspection of the component.

© 46485-0

Fig. 893

Refitting the exhaust manifold

1. m Clean the mating surfaces.
m Apply DEUTZ S1 assembly product to the new stud bolts.
m Fit the new stud bolts.
m Fit the new gaskets.

© 46484-0

Fig. 894

30-240
Method of intervention
2. m Fit exhaust pipe (2).
m Install spacer bushes (1).
1

© 46486-0

Fig. 895
3. m Tighten new nuts (2).

Fig. 896
4. m Tighten all the nuts (1): 25 Nm.
NOTE
Tighten in order from inside out, starting from nut (1).

m Fit the turbocharger.

See para. 30.3.43 - Removal and refitting ... - page 30-155

Fig. 897

30-241
 Method of intervention
30.4.4 - Removal and refitting of the fuel filter head.
Special tools:
l Special wrench: 170050
l Plugs and caps: 170160
DANGER
After switching off the engine, wait at least 30 seconds before carrying out any work on the fuel system!

WARNING
During work on the fuel system always maintain conditions of the maximum cleanliness.
Thoroughly clean the area around the components to be worked on. Dry any wet areas with a compressed air jet.
When handling fuel observe the safety directives and specific local regulations.
All lines and unions should be closed immediately after opening using new, clean plugs or caps. Remove plugs and
caps only immediately prior to assembly. Collect operating materials in suitable containers and dispose of them in
compliance with the applicable regulations.
Removal of the fuel filter head.
1. m Unscrew hollow screws (1)
m Remove the seals.
NOTE
Collect any leaked fuel and dispose of it properly.

Fig. 898
2. m Remove screws (1).
m Remove fuel filter head (2).
1

© 46584-0

Fig. 899

30-242
Method of intervention
3. m Carry out a visual inspection of the component.

© 46585-0

Fig. 900

Refitting the fuel filter head.

1. m Fit the fuel filter head.
m Fit the nut (1).
m Tighten screws (2). 1 2

© 46586-0

Fig. 901
2. m Fit the nut (1).
m Tighten screws (2). 1
m Tighten the screws: 30 Nm.

© 46523-1

Fig. 902

30-243
 Method of intervention
3. m Tighten the hollow screw (1) with the new O-rings: 39 Nm.
m Tighten the hollow screw (2) with the new O-rings: 39 Nm.
WARNING 2

Route the flexible pipe without friction or tension points. 1

NOTE
Bleed the fuel system as indicated in the instruction manual,
using the hand pump on the fuel pre-filter.

© 46583-1

Fig. 903

30.4.5 - Assembly and disassembly of the temperature sender

NOTE:
Collect operating materials in suitable containers and dispose of them in compliance with the applicable regulations.

NOTE:
The draining and replenishing of engine fluids and lubricants must be carried out in accordance with the instructions
given in the documentation provided by the manufacturer of the vehicle/appliance.

Removal of the temperature sender

1. m Unlock and disconnect wiring connectors (1).

© 46353-1

Fig. 904
2. m z Unscrew the temperature sensor (1)

© 46374-0

Fig. 905

30-244
Method of intervention
3. m Carry out a visual inspection of the component.

© 44084-0

Fig. 906

Refitting the temperature sender

1. m Tighten the temperature sender (1): 24 Nm.
NOTE:
Check that the seal is present.
1

© 46374-0

Fig. 907
2. m Reconnect wiring connector (1).
NOTE:
Check that the connection is made correctly.

© 46353-1

Fig. 908

30-245
 Method of intervention
30.4.6 - Removal and refitting the engine block
Removing the engine block
1. m Remove the hollow connector from the engine block
m Remove screws (1).

© 46432-0

Fig. 909
2. m Withdraw the engine block (1).
m Carry out a visual inspection of the components.
1

© 46434-0

Fig. 910

Fitting the engine block

1. WARNING
Check the mobility of the adjustment rod.

m Operate the stop lever between the start and stop position.
m Fit a new O-ring (1).
m Lightly lubricate the O-ring.

© 46417-0

Fig. 911

30-246
Method of intervention
2. m Press and hold down the adjustment rod in the stop position, using
the stop lever.
m Insert the engine block (1). 1

© 46434-0

Fig. 912
3. m Tighten the screws (1): 21 Nm
m z Fit the hollow connector on the engine block.

© 46432-0

Fig. 913

30.4.7 - Removal and refitting of the alternator (with drivebelt)

Commercially available tools:
l V-belt tension tester: 8115
WARNING
Only check/re-tension/change the V-belt while the engine is stationary.

NOTE:
After fitting a new V-belt, check the tension again after running the engine for 15 minutes.

30-247
 Method of intervention
Removal of the alternator
1. m Disconnect the leads from the negative terminal of the battery.
m Disconnect the alternator wiring.
Note the relative connection positions of the wiring!
n (1) = W terminal 1
n (2) = D+ terminal
n (3) = B+ terminal
2

© 46557-0

Fig. 914
2. m Loosen the screws (1)

© 46375-0

Fig. 915
3. m Remove the V-belt.
m Loosen screw (1). 2
m Unscrew screws (3) 3
m Remove alternator (2) 1
m Carry out a visual inspection of the components.

© 46558-0

Fig. 916

30-248
Method of intervention
Refitting the alternator
1. m z Fit the alternator (3)
m Tighten screws (2).
n M8-10.9: 30 Nm

m Tighten screw (1). 1 2 3

n M8-10.9: 30 Nm

m Tighten banjo bolt (4).

n M8-10.9: 40 Nm

4
© 46558-1

Fig. 917

Fitting the V-belt

1. m Fit the V-belt.
m Using a suitable tool, push bracket (1) in the direction of the arrow.

© 46375-1

Fig. 918
2. m z Pre-tighten the screws (1).

© 46375-0

Fig. 919

30-249
 Method of intervention
Check the V-belt tension using the specific tester
1. m Lower the indicator arm (1) of the belt tension gauge.

© 44591-0

Fig. 920
2. m Apply the tension gauge to the V-belt.
NOTE:
The V-belt must be between the guides on the gauge
(arrowed).

© 46559-0

Fig. 921
3. m Press the gauge against the V-belt by depressing button (1) until
you hear a click.
m Read off the value at the point where the indicator arm crosses the
numbered scale on the gauge (arrowed).
n After initial assembly: 650 Nm
n Check after 15 minutes of operation under load: 400 Nm
1
NOTE:
Note the two different units of measurement on the
scale.

m If the nominal value is not obtained, repeat the tensioning procedure.

© 46560-0

Fig. 922

30-250
Method of intervention
4. m Tighten (1) the screws.
n M8-10.9: 30 Nm

© 46375-0

Fig. 923
5. m Connect the wiring to the alternator terminals.
Note the relative connection positions of the wiring!
n (1) = W terminal
n (2) = D+ terminal 1
n (3) = B+ terminal

m Re-connect the lead to the negative terminal of the battery. 2

© 46557-0

Fig. 924

30.4.8 - Disassembly and assembly of the starter

Disassembly of the starter
1. m Disconnect the leads from the negative terminal of the battery.
m Disconnect the wiring connectors.
m Remove screws (1). 1
m Remove the starter motor.
m Carry out a visual inspection of the components.

© 46556-0

Fig. 925

30-251
 Method of intervention
Assembly of the starter
1. m Locate the starter motor.
m Tighten (1) the screws.
n M10x38-10.9: 60 Nm
1
n M8 nut: 40 Nm
n Stud bolt: 10 Nm

m Re-connect the wiring connectors

m Re-connect the lead to the negative terminal of the battery.

© 46556-0

Fig. 926

30-252
Method of intervention
30.5 - D0 - Transmission
30.5.1 - Transmission - Adjusting endfloat of planetary reduction unit gears
1. 1 - Fit the hub (2) on the gearbox (1) and fasten in position with the circlip
(3).

Fig. 927
2. Using a feeler gauge “A”, check the endfloat “R” between the hub (2) and
the gear (4).

Fig. 928
3. Calculate the thickness “S” of the shims to be installed between the hub (2)
and the circlip (3) with the following formula:
S=R–F
where: S = final shim pack thickness
R = value measured
F= nominal endfloat (0.4 ± 0.2 mm)
Example:
R = 1.30
Fig. 929
S = 1.30 - 0.4 = 0.90 mm

30.5.2 - Transmission - Adjusting spring preload

1. Measure and note the dimension “D” of the spacer (1). Example: D = 21.50

Fig. 930

30-253
 Method of intervention
2. Assemble a shim pack (2) with a total thickness “S” which, when added to
the dimension “D” of the spacer (1), equals the nominal value “F” of 25.25
mm.
Example:
D = 21.50

F = 25.25

S = F – D = 25.25 – 21.50 = 3.75

Fig. 931
3. Assemble the pack with:
m 4 shims measuring 0.50 mm = 2.00
m 5 shims measuring 0.20 mm = 1.00
m 5 shims measuring 0.15 mm = 0.75

After assembling the shim pack (2), check that the sum of the spacer (1)
and the shim pack is effectively equal to the nominal value “F”.

Fig. 932
4. Fit the spacer (3) and install the spacer (1) on the clutch housing (4).

Fig. 933
5. While keeping the piston (10) compressed, measure the dimensions “C”
and “L”, and calculate the value “M” with the following formula:
M=C–L
Example:
C = 20.32

L = 3.52

M = 20.32 – 3.52 = 16.80 Fig. 934

6. Calculate the thickness “A” of the shim pack (5) to be installed under the
spacer (1) with the following formula:
A = 17.70 – M
Example:
A = 17.70 – 16.80 = 0.90

Fig. 935

30-254
Method of intervention
7. Assemble the shim pack (5) with the calculated thickness “A”, using only
the shims used to assemble shim pack (2).

Fig. 936
8. Fit the shim pack (5) and the spacer (1), and check that the new dimension
X is between 17.65 and 17.75 mm, as described in step (4).
If the value X is not within the permissible range, reassemble the shim pack
(5) accordingly to achieve the correct measurement.
If the value X is within the permissible range, remove the spacer (1), then
refit the clutch housing, starting from step (12).

Fig. 937
9. The remaining shims will be installed above the spacer (1).
10. IMPORTANT
Fit the ring nut 2.1214.006.7 and tighten to 15 Kgm.

30.5.3 - Transmission - Adjusting secondary shaft (part No. 927798)

1. Fit the shoulder washers in position “A”, selecting the sizes necessary from
part numbers 2.1599.568.0/10, 2.1599.737.0, 2.1599.738.0, 2.1599.739.0
and 2.1599.740.0 to cancel out the endfloat
A

Fig. 938

30.5.4 - Transmission - Adjusting differential bearing preload

1. Locate complete differential (10) in the transmission casing.

Fig. 939

30-255
 Method of intervention
2. Install the flanges (4) and (7) and secure in position with screws (11).
While tightening screws (11), rotate the differential unit to help seat the
bearings. Bearings: Transmission oil Screws: 32 to 40 Nm (23.6-29.5 lb.ft.)

Fig. 940
3. Place a dial gauge with magnetic base “A” on the crown wheel side of the
differential carrier (4) and set it to zero on the end face of the differential
while simultaneously forcing the differential with lever “B” towards the op-
posite side.

Fig. 941
4. Force the differential axially towards the crown wheel side and measure
the endfloat “G”.
If the endfloat is zero, adjust the shim pack (9) on the side opposite the
crown wheel to 0.70 mm and repeat the procedure to measure the endfloat
“G”.

Fig. 942
5. Add 0.10 mm to the measured end float value “G” and round up to the nearest 0.05 mm to determine the shim thickness to be
added under the outer ring of bearing (8) on the opposite side to the crown wheel.
Example:
m Measured value: 0.28 mm
m Nominal value: 0.28 + 0.10 = 0.38 mm
m Actual shim thickness to be added: 0.40 mm

30-256
Method of intervention
30.5.5 - Transmission - Adjusting pinion position
1. Note the value “E” stamped on the crest of one of the teeth of pinion (1).
In this example: + 0.15 mm

Fig. 943
2. Install pinion (1) without shims (12) in the transmission casing.

Fig. 944
3. Locate complete differential (10) in the transmission casing

Fig. 945
4. Install the flanges (4) and (7) and secure in position with screws (11).
Note
Screws: 32 to 40 Nm (23.6 to 29.5 lb.ft.)

While tightening the screws (11), check that there is free play between the
differential and the pinion (1). If the differential is in contact with the pinion,
adjust the shim packs installed under the outer races of the bearings to
reduce the thickness of the pack on the crown wheel side and increase the
thickness of the pack on the opposite side by the same amount. Fig. 946

5. Use a feeler gauge to measure the distance “D” between the end face of
pinion (1) and the 174 mm diameter section of the differential (10) (in this
example 4.85).

Fig. 947

30-257
 Method of intervention
6. Calculate dimension “R” by adding the dimension “E” read previously on the crest of the pinion tooth (1) to the nominal value
of 4.00 mm.
If the value “E” is positive, as in the case shown in the figure, add it to the nominal value of 4.00 mm:
R= 4.00 + “E”, therefore R = 4.00 + 0.15 = 4.15
If “E” is negative, subtract it from the nominal value of 4.00 mm.
R= 4.00 – “E”, therefore R = 4.00 – 0.15 = 3.85
7. If the measured value “D” differs from the calculated value “R”, calculate the difference between “D” and “R”. The resulting
value “S” is the shim thickness to be installed under bearing (2) of pinion (1).
Formula: S = D – R which, in this example, gives:
S = 4.85 - 4.15 = 0.70 mm
8. Remove screws (11) on both sides, leaving just one in position for safety.

Fig. 948
9. Using a suitable drift made of soft material, separate differential flanges (4)
and (7) from the transmission casing.
Note
Tighten the ring nut to a nominal torque of 460 ± 20 Nm
using output shaft of the groundspeed PTO, then tighten to
472 ± 20.5 Nm

Fig. 949

30-258
Method of intervention
30.5.6 - Adjusting mounts - Assembly
1. Repeat the removal steps in reverse order.
Mating faces: Loctite 510

Fig. 950
2. Temporarily fit spacer (6) and screw (5) without shims and tighten.
Screw: 29.4 Nm (21.7 lb ft)
After tightening to the specified torque, rotate the axle housing while hold-
ing the axle shaft still to allow the bearings to seat correctly, then tighten
screw (5) again.
Repeat the procedure until screw (5) no longer turns.

Fig. 951
3. Remove screw (5) and spacer (6), then use a depth gauge “F” and the
shims “G”, calibrated to approximately 25 mm, measure dimensions “A”
and “B”.

Fig. 952
4. Calculate thickness “S” of shim pack (7) to be installed under spacer (6)
with the formula: S = A – B
round the calculated value by ± 0.02 mm

Calculation example 1:
dimension “A” = 97.44 mm, dimension “B” = 95.95 mm
S = 97.44 – 95.95 = 1.49 mm
thus the final thickness S of shims (7) will be 1.50 mm.
Calculation example 2: Fig. 953

dimension “A” = 97.37 mm, dimension “B” = 95.95 mm

S = 97.37 - 95.95 = 1.42 mm
therefore, the final thickness S of the shims (7) is 1.40 mm.

30-259
 Method of intervention
5. Fit shim pack (7), spacer (6) and secure in positions by tightening screw (5).
Screw: 177 ± 9 Nm (130.5 ± 6.6 lb.ft.)

Screw: Loctite 270

Fig. 954
6. Note
Lubricate the bearing (10) and the lip of the oil seal (12).

Note
Make certain the oil seal (12) is installed the right way round.

30.5.7 - Shuttle - Removing shuttle unit (AGROFARM 410 -> ZKDW470200TD30001,

AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)
1. Place the shuttle unit (1) on support T1 and remove the screws (2) (q.ty 7).

Fig. 955
2. Remove the complete flange (3).

Fig. 956
3. Remove bolts (4) (q.ty 10).

Fig. 957

30-260
Method of intervention
4. Remove the forward drive clutch unit (5).

Fig. 958
5. Retrieve the springs (7) and the pins (8) from the reverse drive clutch unit
(6).

Fig. 959
6. Remove the O-rings (9).
NOTE:
Replace the O-rings at every disassembly.

Fig. 960

30-261
 Method of intervention
30.5.8 - Shuttle- Removing/installing forward drive clutch (AGROFARM 410 -> ZK-
DW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)

Fig. 961 - Forward drive clutch unit

30-262
Method of intervention
Removal
1. Remove the 2 screws (1) and remove the plate (2).
Mark the installation hole for the pin (3).

Fig. 962
2. Remove the complete clutch pack, consisting of 4 corrugated springs (4), 4
friction discs (5), 3 steel discs (6) measuring 3 mm in thickness and 1 steel
disc (7) measuring 6.5 mm in thickness.
Ensure that the friction discs and steel discs are kept in the correct order
during removal.

Fig. 963
3. Remove the hub (8) and retrieve the Belleville washer (9).

Fig. 964
4. Blow compressed air at low pressure through the hole “A” in the clutch
housing (10) to expel the piston (11).
Restrain piston (11) as it could be expelled at high speed and be damaged.

Fig. 965
5. Check the condition of O-rings (12) and (13) and replace if necessary.

Fig. 966

30-263
 Method of intervention
6. Only if necessary, remove the bearing (14) from the hub (8).

Fig. 967

Assembly
1. Only if removed previously, refit the bearing (14) on the hub (8) using a
suitable presser tool.

Fig. 968
2. Fit the O-rings (12) and (13) in the clutch housing (10).
O-ring: hydraulic oil.
NOTE:
To facilitate installation of O-ring (13), stretch it slightly at
several points around their circumference so that the entire
circumference is held in place in the respective seat.

Fig. 969
3. Fit the piston (11) in the clutch housing (10), ensuring that it is installed fully
in its seat.

Fig. 970
4. Fit the Belleville washer (9) in the clutch housing.
Ensure that the Belleville washer (9) is oriented correctly.

Fig. 971

30-264
Method of intervention
5. Mount the hub (8) and ensure that the bearing (14) is fully installed onto the
Belleville washer (9).

Fig. 972
6. Fit the first steel disc (7), the friction disc (5) and the corrugated spring (4).
Ensure that the 6.5 mm thick steel disc (7) is installed as the first disc.
Friction disc (hydraulic oil)

Fig. 973
7. Complete assembly of the clutch pack, installing the discs in the following
sequence: one steel disc (6), one friction disc (5) and one corrugated spring
(4).
Friction discs: Hydraulic oil

Fig. 974
8. Fit the plate (2) and fasten in place with the screws (1).
Position the plate correctly so that the pin (3) installs in the hole marked
during disassembly

Fig. 975

30-265
 Method of intervention
30.5.9 - Shuttle - Removing/installing reverse drive clutch (AGROFARM 410 -> ZK-
DW470200TD30001, AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 ->
ZKDW550200TD30001)

Fig. 976 - Reverse drive clutch unit

30-266
Method of intervention
Removal
1. Remove roller cage (1).

Fig. 977
2. Remove the complete clutch pack, consisting of 4 corrugated springs (2), 4
friction discs (3), 3 steel discs (4) measuring 3 mm in thickness and 1 steel
disc (5) measuring 6.5 mm in thickness.
DANGER
Ensure that the friction discs and steel discs are kept in the
correct order during removal.

Fig. 978
3. Remove the hub (6)

Fig. 979
4. Only if necessary, remove the bearing (7) from the hub (6) using three
screws as a presser tool.

Fig. 980
5. Blow compressed air at low pressure through the hole “A” in the mount (8)
to expel the piston (9).
Restrain piston (9) as it could be expelled at high speed and be damaged.

Fig. 981

30-267
 Method of intervention
6. Check the condition of the O-rings (10) and (11) and replace if necessary.

Fig. 982
7. Remove circlip (12) and remove spacer (13).

Fig. 983
8. Remove circlip (14).

Fig. 984
9. Remove the clutch housing (15) from the support (8).

Fig. 985
10. Remove the bearing (16) from the clutch housing (15).

Fig. 986

30-268
Method of intervention
11. Remove the seal rings (17) from the mount (8).

Fig. 987

Assembly
1. Fit the seal rings (17) on the mount (8).
Seal rings: Hydraulic oil

Fig. 988
2. Fit the bearing (16) on the clutch housing (13).

Fig. 989
3. Fit the clutch housing on the mount (8) and fasten in place with the circlip
(14).

Fig. 990
4. Fit spacer (13) and secure it in position with circlip (12).

Fig. 991

30-269
 Method of intervention
5. Fit the O-rings (10) and (11) in the clutch housing (15).
Friction discs: hydraulic oil.
N.B.
To facilitate installation of O-rings (11), stretch them slightly
at several points around their circumference so that the en-
tire circumference is held in place in the respective seat.

Fig. 992
6. Fit the piston (9) in the clutch housing (15), ensuring that it is installed fully
in its seat.

Fig. 993
7. Using a suitable press and presser tool, install the bearing (7) on the hub
(6).
Fit the hub (6) on the clutch housing (15).

Fig. 994
8. Fit the first steel disc (5), the friction disc (3) and the corrugated spring (2).

Fig. 995
9. Complete assembly of the clutch pack, installing the discs in the following
sequence: one steel disc (4), one friction disc (3) and one corrugated spring
(2).
Friction discs: Hydraulic oil

Fig. 996

30-270
Method of intervention
10. Fit the roller bearing cage (1) on the hub (6).

Fig. 997

30-271
 Method of intervention
30.6 - F0 - Front axle
30.6.1 - Front axle - Adjusting differential
1. Insert bearing retainer (2) in sleeve (1).
Fit the 17 balls (3) and the disc (4).
Important
No shims should be installed at this stage.

Fig. 998
2. Install the axle lock (6) on the differential unit (5), and fit suitable shims (7)
to eliminate any play between the bearing retainer and the circlip (8)

Fig. 999
3. Remove the differential lock and install some of the shims (7) between the
disc (4) and the bearing retainer (2), then refit the lock on the differential
unit.

Fig. 1000
4. Secure the differential lock (6) with the remaining shims (7) and the circlip
(8).

Fig. 1001

30-272
Method of intervention
5. With sleeve (1) moved towards the differential, check that the flat part “A” of
sleeve (1) is in contact with the balls (3) as shown in the figure.
If not, repeat steps 4, 5 and 6 until the correct condition is achieved.

Fig. 1002
6. Fit the fork (9) complete with shoes (1) and the lever (11).

Fig. 1003
7. Secure lever (11) in position with spring pin (12).

Fig. 1004
8. Fit the differential lock piston (13).

Fig. 1005
9. Fit the cover (14) and the relative O-ring (15) and tighten the screws (16).

Fig. 1006

30-273
 Method of intervention
10. Fit complete control rod assembly (17).
Fit pin (18) and washer (19) and secure them in position with split pin (20).

Fig. 1007
11. Adjust the length “B” of the differential lock control rod (13) so that, with the
sleeve (1) in the indicated position, the shoes (10) are not pushed against
the sleeve itself.

Fig. 1008
12. Note dimension “E” stamped on the crest of a tooth of the pinion (1).
NOTE:
In the example illustrated: E = -0.05 mm

Fig. 1009
13. Fit the inner bearing race (2) on the pinion (1).

Fig. 1010

30-274
Method of intervention
14. Install the outer bearing race (2) in differential carrier (3)

Fig. 1011
15. Install pinion (1) and flanges (4) and (5), complete with outer bearing races
(6) and (7), in differential carrier (3) and, using a depth gauge “A”, measure
distance “X”.
Rotate the pinion (1) in both directions to so that the bearing (2) can bed
in properly.
Fit a cylindrical pin “C” (Part No. 2.1651.109.0) measuring 2.5 mm in diam-
eter on the outer race of the bearing on the crown wheel to compensate for
the difference in external diameter between bearings (7) and (6) (respec-
tively 90 and 85 mm).
Fig. 1012
16. Calculate the distance “D” from the axis of rotation of the differential to the
pinion head (1) with the following formula: D = X - R
where: R = 45.00 = radius of bearing (6) on the opposite side to the crown
wheel.
Example:
Dimension “X” = 107.75 mm
Radius “R” = 45.00
D = 107.75 - 45.00 = 62.75 mm

Fig. 1013

30-275
 Method of intervention
17. Remove the pinion (1), outer bearing race (2) and flanges (4) and (5), and
assemble a shim pack (8) of thickness “S” calculated using the following
formula: S = D - Theoretical value + E
where:
mS = final shim pack thickness (8)
mD = measurement calculated in step 5
m Theoretical value = 61.00
m E = measurement stamped on pinion crest (1)

Example 1 (negative “E” value)

mD = 62.75 mm Fig. 1014
mE = - 0.05 mm
m Theoretical value = 61.00
m S = 62.75 - 61.00 - 0.05 = 1.70 mm

Example 1 (positive “E” value)

m D = 62.75 mm
m E = + 0.15 mm
m Theoretical value = 61.00
m S = 62.75 – 61.00 + 0.15 = 1.90 mm
18. Fit the shim pack (8) and the outer bearing race (2) in differential carrier (3).

Fig. 1015
19. Install pinion (1) in the differential carrier and install spacer (9) and a shim
pack (10) approx. 1.50 mm thick.
DANGER
( ! ) Lubricate bearing.

Fig. 1016
20. Install bearing assembly (11) in differential carrier (3) and seat it using a
suitable driving tool.
NOTE:
To facilitate installation of the bearing, position the differen-
tial carrier vertically and rest the end face of the pinion on
a spacer.

Fig. 1017

30-276
Method of intervention
21. Fit spacer (12) on pinion shaft (1) and secure it by tightening nut (13).
Ring nut: 206 ÷ 226 Nm (151.8 ÷ 166.6 lb. ft.)
The ring nut is turned anti-clockwise to tighten.
When tightening the nut, take care not to preload the bearings (2) and (11).
If the bearings are preloaded, assemble a thicker pack of shims (10).

Fig. 1018
22. Fit a dial gauge with a magnetic base “F” as indicated, with the probe per-
pendicular to the end face of the pinion (1).
Preload the gauge by approximately 2 mm then apply leverage to the pin-
ion and read the play “G” of bearings (2) and (11).

Fig. 1019
23. Calculate the thickness “P” of the shim pack (10) to be installed under spac-
er (9) using the following formula, rounding the value down to the nearest
0.05 mm.
“P” = Installed shim thickness - measured play “G”
Example: (measured play = 0.17 mm)
P = 1.50 – 0.17 = 1.33 (rounded down to 1.30 mm)
m

Example: (measured play = 0.23 mm)

m P = 1.50 – 0.23 = 1.27 (rounds down to 1.25 mm)
Fig. 1020
24. Remove the nut ring (13) and remove the pinion assembly, the spacer (9)
and the inner bearing race (11).
The ring nut is turned clockwise to loosen.

Fig. 1021
25. Alter shim pack (10) to the thickness “P” calculated in step 12 and refit the
pinion as described in steps 8, 9 and 10.
Rotate the pinion while tightening the ring nut, to ensure that the bearings
(2) and (11) do not stick.

Fig. 1022

30-277
 Method of intervention
26. Rotate the pinion both directions, tapping it lightly to seat the bearings (2) and (11), and check that there is no pinion endfloat
as described in step 12.
NOTE:
If the pinion still exhibits endfloat, repeat the 3 previous steps.

27. Fit the crown wheel (2) and the screws (3) on the differential (1).
Screws: 75 ± 4 Nm (55.3 ± 3 lb.ft.)

Fig. 1023
28. Fit differential assembly (1) in differential carrier (4) and, using a suitable
tool, install the inner race of bearing (5).
Take particular care to install the bearing (5) and the differential (1) the right
way around relative to the differential carrier (4).

Fig. 1024
29. Using a suitable tool, install the inner race of bearing (6).

Fig. 1025
30. Install the outer race of bearing (5) on the flange of the side opposite the
crown wheel (7).
Fit the outer race of bearing (6) in the crown-wheel side flange (8).

Fig. 1026

30-278
Method of intervention
31. Install an 0.5 mm thick shim pack (9) and the complete flange (7) in the dif-
ferential carrier (4), and fasten by tightening the screws (10).

Fig. 1027
32. Install a 1.5 mm thick shim pack (11) and the complete flange (8) in the dif-
ferential carrier (4), tightening the screws (12).

Fig. 1028
33. Fit a dial gauge with a magnetic base “F” as indicated, with the probe per-
pendicular to the differential hub (1).
Preload the dial gauge by approx. 2 mm and reset to zero. Use a lever to
apply force under the differential (1), and measure the endfloat “G”
Example: (measured play “G” = 0.37 mm)

Fig. 1029
34. Calculate the total thickness of shims “T” to be installed under the flanges
by subtracting the measured endfloat “G” from the thickness of shims (9)
and (11) installed the under flanges (7) and (8), rounding the value obtained
down to the nearest 0.05 mm.
Example:
mThickness of installed shims (9) and (11): 2.00 mm
mMeasured play “G” = 0.37 mm
m Total shim thickness “T”: 2.00 - 0.37 = 1.63 mm, which rounds down

to 1.60 mm
Remove flanges (7) and (8) and shims (9) and (11). Fig. 1030
35. Change the thickness of shim pack (11) to 1.00 mm, and reinstall it with
flange (6).
Bearing: oil
Tighten screws (12).

Fig. 1031

30-279
 Method of intervention
36. Calculate the thickness “H” of the shim pack (9), subtracting the thickness
of the shims (11) installed under the flange (8) from the value “T” calculated
in step 9.
Example: H = T - 1.00 = 1.60 -1.00 = 0.60 mm
Form a shim pack (9) of thickness “H”, install with flange (7) and fasten by
tightening the screws (10).
While tightening the screws, rotate the differential to ensure that bearings
(5) and (6) turn smoothly.
Bearing: oil
Fig. 1032
37. Rotate the pinion and crown wheel in both directions to seat the bearings
(5) and (6), and check that the differential has no endfloat as described in
steps 8 and 9.

Fig. 1033
38. Using a feeler gauge “A”, check that dimension “D” between the end face
of pinion (13) and differential case (1) is correct within a tolerance of ± 0.10
mm.

Fig. 1034
39. Distance “D” = theoretical distance + value “E”
where:
Theoretical distance = 1.00 mm
m

Value E = value stamped on crest of one of the pinion teeth.

m

Example 1 (value “E” positive)

mTheoretical distance = 1.00 mm
mE = + 0.10 mm
m D = 1.00 + 0.10 = 1.10 mm
m Acceptable values: 1.00 to 1.20 mm

Example 2 (value “E” negative) Fig. 1035

m Theoretical distance = 1.00 mm

m E = - 0.05 mm
m D = 1.00 - 0.05 = 0.95 mm
m Acceptable values: 0.85 to 1.05 mm

30-280
Method of intervention
Adjustment of pinion and crown wheel backlash
1. Place a dial gauge with magnetic base “F” as indicated, with the probe per-
pendicular to the tooth flank on the external diameter of the crown wheel.
Preload the gauge by approx. 2 mm and measure the backlash “Z” be-
tween the pinion and crown wheel by turning the differential back and forth
in both directions.
Normal backlash “Z” (100 HP): 0.15 to 0.20 mm
Take four measurements 90° apart and calculate the average.

Fig. 1036
2. If the backlash “Z” is less than 0.15 mm, remove shims from shim pack (11)
(crown wheel side) and add the same number of shims to the shim pack (9)
(opposite side to crown wheel). If backlash “Z” is greater than 0.20 mm add
shims to shim pack (11) (crown wheel side) and remove the same number
of shims from shim pack (9) (opposite side to the crown wheel).
The sum total thickness of shim packs (11) and (9) should be the same as
the value obtained when checking the preload of the differential bearings.
Recheck backlash “Z” and, if necessary, continue to adjust the shims until
the backlash is within the specified tolerance limits.
Fig. 1037
3. Finally tighten down screws (10) and (12) securing flanges (7) and (8).
Screws: 45 ± 2 Nm (33.2 ± 1.5 lb.ft.)
Screws: Loctite 242

Fig. 1038

Assembly
1. Stake ring nut (13) at the two points corresponding to the notches in pinion
(14).

Fig. 1039

30-281
 Method of intervention
2. Using a suitable tool, install oil seal (21) in differential carrier (15).
Seal ring: grease

Fig. 1040

30-282
Method of intervention
30.7 - R0 - Rear lift
30.7.1 - ADJUSTING LIFT (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 410 ->
ZKDW470200TD30001)
1. DANGER
This procedure must be performed with the lift installed on the transmission and with all feed and return lines
connected.

DANGER
Before starting the tractor, make sure that the yellow lift control lever is in the maximum depth position. When
starting the engine, make sure that the hand throttle lever is in the idle position.
2. Attach either an implement or a 200 kg weight to the 3-point linkage.
3. Move yellow lever (1) to the maximum height position.

Fig. 1041
4. Check that lever (2) is against the lift (3).
If not, or if lever (2) is restricting the travel of yellow lever (1), adjust the
length of tie-rod (4).

Fig. 1042
5. After making the adjustment, move the yellow lever (1) to the “control” posi-
tion and green lever (5) to position “12”.

Fig. 1043
6. Start the engine and run at idle speed, and move the green lever (5) slowly
to the “O” position.
DANGER
Observe the arms of the lift as the lift raises.

Fig. 1044

30-283
 Method of intervention
7. When the lift stops, check that the hole “A” on the right hand arm (6) is
aligned with the hole on the lift housing (3).

Fig. 1045
8. If the holes are not aligned, remove the cap (7) and adjust the height with
the adjuster screw (8).
Tighten the adjuster screw (8) to raise the arms.
Loosen the adjuster screw (8) to lower the arms.
Tighten the check nut (9) and refit the cap (7).
Always fit a new washer after removal.

Fig. 1046
9. After making the adjustment, move the yellow lever (1) to the maximum
height position and green lever (5) to position “12”.

Fig. 1047
10. Check if the hole “A” on the right hand arm (6) is aligned with the hole on
the lift.

Fig. 1048
11. If the holes are not aligned, loosen the screw (10) until they are correctly
aligned.
Draw a horizontal line at a distance of 10-12 mm from the seal on the cyl-
inder strut (11).
Loosen the screw (10) by an additional turn and secure in this position with
the check nut (12).
Check that the line drawn on the cylinder strut is now near the seal.

Fig. 1049

30-284
Method of intervention
12. Adjust the length of the tie-rod (13) so that the yellow lever (1) can complete
a full stroke to the maximum height position without straining the screw
(10).

Fig. 1050
13. Move the yellow lever (1) to the “control” position and the green lever (5)
to position “12”.
The lift should lower completely.

Fig. 1051
14. Move the green lever slowly towards position “O” until the lift starts to move.

Fig. 1052
15. The lift must start to move when green lever (5) is in position “4”.
If the lift starts to move earlier (near positions “5” or “6”), lengthen the tie-
rod (4).
If the lift starts to move later (near positions “3” or “2”), shorten the tie-rod
(4).

Fig. 1053

30-285
 Method of intervention
30.7.2 - ADJUSTING LIFT (AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 420
-> ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001, AGROFARM 430 ->
ZKDW550200TD30001)
1. DANGER
This procedure must be performed with the lift installed on the transmission and with all feed and return lines
connected.

DANGER
Before starting the tractor, make sure that the yellow lift control lever is in the maximum depth position. When
starting the engine, make sure that the hand throttle lever is in the idle position.
2. Attach either an implement or a 200 kg weight to the 3-point linkage.
3. Move yellow lever (1) to the maximum height position.

Fig. 1054
4. Check that lever (2) is against the lift (3).
If not, or if lever (2) is restricting the travel of yellow lever (1), adjust the
length of tie-rod (4).

Fig. 1055
5. After making the adjustment, move the yellow lever (1) to the “control” posi-
tion and green lever (5) to position “12”.

Fig. 1056
6. Start the engine and run at idle speed, and move the green lever (5) slowly
to the “O” position.
DANGER
Observe the arms of the lift as the lift raises.

Fig. 1057

30-286
Method of intervention
7. When the lift stops, check that the hole “A” on the right hand arm (6) is
aligned with the hole on the lift housing (3).

Fig. 1058
8. If the holes are not aligned, remove the cap (7) and adjust the height with
the adjuster screw (8).
Tighten the adjuster screw (8) to raise the arms.
Loosen the adjuster screw (8) to lower the arms.
Tighten the check nut (9) and refit the cap (7).
Always fit a new washer after removal.

Fig. 1059
9. Attach either an implement or a 200 kg weight to the 3-point linkage.
10. Move yellow lever (14) to the maximum height position.

Fig. 1060
11. Check that lever (15) is up against stop (16).
If not, or if lever (15) is restricting the travel of yellow lever (14), adjust the
length of tie-rod (17).

Fig. 1061
12. After making the adjustment, move the yellow lever (14) to the “control”
position and green lever (18) to position “12”.

Fig. 1062

30-287
 Method of intervention
13. Start the engine and run at idle speed and slowly move yellow lever (14) to
max. height position.

Fig. 1063
14. When the lift stops, check that the end of piston (19) is flush with cylinder
(20).

Fig. 1064
15. If piston (19) protrudes from the cylinder or stops inside it, adjust the travel
with the tie-rod (21).
Shorten the tie-rod to increase the protrusion of the piston from the cylinder.
Lengthen the tie-rod to cause the piston to retract inside the cylinder.

Fig. 1065
16. Move the yellow lever (14) to the control position and the green lever (18)
to position “0”.
DANGER
Observe the arms of the lift as the lift raises.

Fig. 1066
17. Check that piston (19) protrudes approximately 5 mm from cylinder (20).

Fig. 1067

30-288
Method of intervention
18. If piston (19) does not stop in the correct position, adjust the travel with the
screw (22).
Screw in the screw if the piston protrudes by too much (7 mm).
Screw out the screw if the piston protrudes by too little (3 mm).
After each adjustment, check if the setting is correct by moving the green
lever (18) to position “12” and then back to position “0”.

Fig. 1068
19. Move the green lever (18) to position “12”.
The lift should lower completely.
Move green lever (18) slowly towards position “0” until the lift starts to move.

Fig. 1069
20. The lift should start to move when the green lever (18) is in position “4”.

Fig. 1070
21. If the lift starts to move earlier, (in position “5” or “6”), shorten the tie-rod
(23).
If the lift starts to move later (near positions “3” or “2”) lengthen the tie-rod
(23).

Fig. 1071

30-289
 Method of intervention

PAGE LEFT INTENTIONALLY BLANK

30-290
40 - Wiring diagrams

40-1
 Wiring diagrams
40.1 - Introduction
40.1.1 - Introduction
For easier consultation, this unit has been divided into the following chapters:
l Introduction
m Contains a brief description of the terminology used, the procedures to follow for troubleshooting and repairs, and the

instruments required for fault diagnosis.

l Components list
m Contains the components of the electrical systems, organised by type.
m Indicates the system code, the component code and description, the technical data required for functional testing and

a description of the pin-outs of the ECUs.

l Systems
m Contains the wiring diagrams of the tractor’s systems.

l Wiring harnesses
m Contains the layouts, the wiring diagrams and the positions of connectors on the tractor.

Introduction
This section of the workshop manual is intended as a practical guide to fault diagnosis of the tractor’s electrical and electronic
systems. The following pages provide the technician with all the necessary information regarding the tractor’s systems and compo-
nents. Due to the possible time difference between the introduction of technical modifications (in line with our policy of continuous
product improvement) and the corresponding amendment of our printed documentation, the data contained in this document are
subject to modification and as such are not binding.
Definition of components and symbols
To prevent any misunderstanding or ambiguity, definitions for some of the key terms used in this unit are listed below.
Table 75
TERM DESCRIPTION
Connector Element used to connect two components (e.g. wiring-switch, wiring-wiring)
Temperature sensor Electrical component that converts the temperature of a medium (air, water, oil, etc.) into a voltage
or resistance
Pressure sensor Electrical component that converts the pressure of a medium (air, water, etc.) into a voltage or
resistance
Position sensor Electrical component that converts an angular or linear position into a voltage
Pressure switch Switch that changes state (opens or closes a contact) according to the operating pressure in the
circuit in which it is installed
Thermostat Switch that changes state (opens or closes a contact) according to the temperature of the medium
(air, water, etc.) in which it is immersed.
Switch Mechanical component that opens or closes one or more electrical contacts.
Solenoid valve Valve operated by applying electrical current to a coil (or solenoid)
Chapter “Components” shows the wiring diagrams for certain switches and buttons. The following symbols are used for ease of
interpretation:
Contact between pins CLOSED (stable switch position)

Contact between pins CLOSED (unstable switch position)

Indicator LED

Indicator light

40-2
Wiring diagrams
Diode

General rules
The inspection, maintenance, fault diagnosis and repair operations are essential to ensure that the tractor continues to operate cor-
rectly over time and to prevent malfunctions and breakdowns. This paragraph describes repair procedures and aims to help improve
the quality of repairs.
Modification of the tractor’s electrical/electronic circuits
The manufacturer prohibits any modification or alteration of the electrical wiring for the connection of any non-approved electrical
appliances or components. In particular, if the electrical system or a component is altered without the Manufacturer’s authorisation,
the Manufacturer will accept no liability for any damage to the vehicle and the vehicle warranty will be invalidated.
Main wiring faults
Bad contact between connectors
l The main causes of poor contact between connectors are incorrect insertion of the male into the female connector, deforma-
tion of one or both connectors, and corrosion or oxidisation of the pin contact surfaces.
Defective pin soldering or crimping
l The pins of the male and female connectors make good contact in the crimped or soldered area, but the wires are subjected
to excessive strain, leading to breakage of the insulation and a poor connection or breakage of the wire.
Disconnecting wiring
l If connectors are disconnected by pulling on the cables, or if components are removed with the wires still connected, or if the
wiring is subject to impact by a heavy object this could damage the soldering or crimping of wires on the pins and some wires
may break.
Penetration of water inside connectors
l The connectors are designed to prevent penetration of liquids (water, oil etc.); however, when cleaning the tractor with pres-
sure washers or steam washers water could penetrate or condense in the connectors. As the connectors are designed to
prevent liquid penetration, any water that does get in will be unable to drain out, and thus may cause short circuits across the
pins. It is therefore good practice to dry the connectors with a low pressure jet of compressed air after washing the tractor.
Oil or dirt on connectors
l If the connectors or pin contact surfaces show signs of oil or grease contamination, this will prevent the passage of current
(oil and grease are electrical insulators) creating a poor contact. Clean the connectors thoroughly using a dry cloth or a low
pressure jet of compressed air and use specific products (deoxidising sprays, etc.) to degrease the contacts.
Important
Take care not to bend the pins when cleaning them. Use dry oil-free compressed air.

Removal, refitting and drying of connectors and wiring

When disconnecting wiring, pull on the connectors rather than on the wires themselves. For connectors that are held in position with
screws or levers, fully loosen the screws, then pull on the connector. For connectors that are clipped together, fully depress the clip
then pull the connector apart. After disconnecting connectors, apply water proof covers to prevent contamination of the contacts with
dirt or moisture.
Connecting the connectors. Check the condition of the connectors:
l Make sure the pin contact surfaces are free of water, dirt or oil.
l Check that the connectors are not deformed and that the pins are not corroded or oxidised.
l Check that the connector casings are not damaged or split.
l If a connector is contaminated with oil or grease, or if moisture has penetrated the casing, clean it thoroughly.
l If a connector is damaged, deformed or broken, replace it with a new one.
When connecting connectors, make sure they are properly aligned before applying force. For connectors with clips, insert the two
halves until they clip together.
Cleaning and drying wiring

40-3
 Wiring diagrams
l When wiring is dirty or contaminated with oil or grease, clean it with a dry cloth, or, if necessary, with water or steam. If the
wiring must be cleaned with water, avoid directing the water or steam jet on the connectors; if water penetrates the connector,
clean it thoroughly.
l Check that the connector is not short circuited due to the presence of water by testing for continuity across the pins.
l After checking that the connector is good condition, degrease the contacts using a deoxidising product.
Renewal of damaged electrical components.
l When replacing electrical components (fuses, relays, etc.), use only original parts supplied by the manufacturer.
l When replacing fuses, check that the new fuse conforms to DIN 72581 or ISO 8820 standards, and in particular:
m fuse F1 (100A) DIN 72581/2
m bayonet fuse (F2, F3, etc.) DIN 72581/3C
m fuse F51 (100A) and F52 (200A) ISO 8820.

l The fitting of replacement fuses that do not comply with these standards will invalidate the warranty with immediate effect and
release the manufacturer from all liability.
l When replacing relays, make sure that the new relay conforms to the standards marked on the original relay.
Diagnostic instruments
For the correct diagnosis of any faults in the tractor’s electrical system, the following instruments are required:
l Digital multimeter with the following minimum characteristics:
m AC VOLT 0-600
m DC VOLT 0-600
m OHM 0-32M
m AC AMP 0-10
m DC AMP 0-10

l All Round Tester or computer with “PCTESTER” software installed

l SDF Analyzer
Wire colour codes
Table 76
COLOUR CODES
A Light blue
B White
S Orange
G Yellow
H Grey
L Blue
M Brown
N Black
R Red
S Pink
V Green
Z Purple

40-4
Wiring diagrams
40.2 - Components
40.2.1 - A - Starting and charging (AGROFARM 410 -> ZKDW350200TD25001)
ITA version
Table 77
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-596 40-1290
40-621
40-701
40-714
40-719
A002 04258670 Preheating device 40-596 40-1290
40-621
40-701
40-714
40-719
A003 01182961 Alternator “B+” 40-723 40-1324
40-738
40-791
40-807
A004 01182961 Alternator “D+” 40-723 40-1324
40-738
40-791
40-807
A005 01182961 Alternator “W” 40-723 40-1324
40-738
40-791
40-807
A006 Starter motor “+50” 40-596 40-1324
40-621
40-807
A007 Battery positive ter- 40-723 40-1324
minal 40-738
40-791
40-807
A008 01182961 Alternator “B+” 40-723 40-1327
40-738
40-791
40-807
A009 01182961 Alternator “D+” 40-723 40-1327
40-738
40-791
40-807
A010 01182961 Alternator “W” 40-723 40-1327
40-738
40-791
40-807
A011 +30 Battery 40-637 40-1295
40-641
40-665
40-671
40-750
40-755
40-758
40-807
40-915
40-942
40-976
40-1024
40-1099
40-1130

40-5
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A012 +30 Battery 40-637 40-1295
40-641
40-665
40-671
40-750
40-755
40-758
40-807
40-915
40-942
40-976
40-1024
40-1099
40-1130
40-791
40-877
40-889
40-1076
40-1145
40-1166
A013 +30 Battery 40-596 40-1295
40-621
40-637
40-641
40-665
40-671
40-750
40-755
40-758
40-807
40-915
40-942
40-976
40-1024
40-1099
40-1130
40-791
40-877
40-889
40-1076
40-1145
40-1166
40-701
40-714
40-723
40-738
40-1247
40-1255
A014 Battery positive ter- 40-596 40-1329
minal 40-621
40-701
40-714

40-6
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A015 Battery negative ter- 40-596 40-1330
minal 40-621
40-637
40-641
40-665
40-671
40-750
40-755
40-758
40-807
40-915
40-942
40-976
40-1024
40-1099
40-1130
40-791
40-877
40-889
40-1076
40-1145
40-1166
40-701
40-714
40-723
40-738
40-1247
40-1255
A016 Battery negative ter- 40-596 40-1330
minal 40-621
40-637
40-641
40-665
40-671
40-750
40-755
40-758
40-807
40-915
40-942
40-976
40-1024
40-1099
40-1130
40-791
40-877
40-889
40-1076
40-1145
40-1166
40-701
40-714
40-723
40-738
40-1247
40-1255
A017 Battery positive ter- 40-723 40-1327
minal 40-738
40-791
40-807

40-7
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A018 Starter motor “+50”a 40-596 40-1327
40-621
40-807

USA version
Table 78
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-604 40-1290
40-629
40-705
40-719
40-719
A002 04258670 Preheating device 40-604 40-1290
40-629
40-705
40-719
40-719
A003 01182961 Alternator “B+” 40-728 40-1324
40-743
40-826
40-843
A004 01182961 Alternator “D+” 40-728 40-1324
40-743
40-826
40-843
A005 01182961 Alternator “W” 40-728 40-1324
40-743
40-826
40-843
A006 Starter motor “+50” 40-604 40-1324
40-629
40-843
A007 Battery positive ter- 40-728 40-1324
minal 40-743
40-826
40-843
A008 01182961 Alternator “B+” 40-728 40-1327
40-743
40-826
40-843
A009 01182961 Alternator “D+” 40-728 40-1327
40-743
40-826
40-843
A010 01182961 Alternator “W” 40-728 40-1327
40-743
40-826
40-843

40-8
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A011 +30 Battery 40-647 40-1295
40-652
40-683
40-677
40-764
40-769
40-772
40-843
40-928
40-953
40-992
40-1042
40-1110
40-1137
A012 +30 Battery 40-647 40-1295
40-652
40-683
40-677
40-764
40-769
40-772
40-843
40-928
40-953
40-992
40-1042
40-1110
40-1137
40-826
40-882
40-895
40-1087
40-1186
40-1206
A013 +30 Battery 40-604 40-1295
40-629
40-647
40-652
40-683
40-677
40-764
40-769
40-772
40-843
40-928
40-953
40-992
40-1042
40-1110
40-1137
40-826
40-882
40-895
40-1087
40-1186
40-1206
40-705
40-719
40-728
40-743
40-1247
40-1255

40-9
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A014 Battery positive ter- 40-604 40-1329
minal 40-629
40-705
40-719
A015 Battery negative ter- 40-604 40-1330
minal 40-629
40-647
40-652
40-683
40-677
40-764
40-769
40-772
40-843
40-928
40-953
40-992
40-1042
40-1110
40-1137
40-826
40-882
40-895
40-1087
40-1186
40-1206
40-705
40-719
40-728
40-743
40-1247
40-1255
A016 Battery negative ter- 40-604 40-1330
minal 40-629
40-647
40-652
40-683
40-677
40-764
40-769
40-772
40-843
40-928
40-953
40-992
40-1042
40-1110
40-1137
40-826
40-882
40-895
40-1087
40-1186
40-1206
40-705
40-719
40-728
40-743
40-1247
40-1255

40-10
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A017 Battery positive ter- 40-728 40-1327
minal 40-743
40-826
40-843
A018 Starter motor “+50”a 40-604 40-1327
40-629
40-843

40.2.2 - A - Starting and charging (AGROFARM 420 -> ZKDW390200TD25001)

ITA version
Table 79
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-596 40-1290
40-621
40-701
40-714
40-719
A002 04258670 Preheating device 40-596 40-1290
40-621
40-701
40-714
40-719
A003 01182961 Alternator “B+” 40-723 40-1324
40-738
40-791
40-807
A004 01182961 Alternator “D+” 40-723 40-1324
40-738
40-791
40-807
A005 01182961 Alternator “W” 40-723 40-1324
40-738
40-791
40-807
A006 Starter motor “+50” 40-596 40-1324
40-621
40-807
A007 Battery positive ter- 40-723 40-1324
minal 40-738
40-791
40-807
A008 01182961 Alternator “B+” 40-723 40-1327
40-738
40-791
40-807
A009 01182961 Alternator “D+” 40-723 40-1327
40-738
40-791
40-807
A010 01182961 Alternator “W” 40-723 40-1327
40-738
40-791
40-807

40-11
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A011 +30 Battery 40-637 40-1295
40-641
40-665
40-671
40-750
40-755
40-758
40-807
40-915
40-942
40-976
40-1024
40-1099
40-1130
A012 +30 Battery 40-637 40-1295
40-641
40-665
40-671
40-750
40-755
40-758
40-807
40-915
40-942
40-976
40-1024
40-1099
40-1130
40-791
40-877
40-889
40-1076
40-1145
40-1166
40-1237

40-12
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A013 +30 Battery 40-596 40-1295
40-621
40-637
40-641
40-665
40-671
40-750
40-755
40-758
40-807
40-915
40-942
40-976
40-1024
40-1099
40-1130
40-791
40-877
40-889
40-1076
40-1145
40-1166
40-1237
40-701
40-714
40-723
40-738
40-1247
40-1255
A014 Battery positive ter- 40-596 40-1329
minal 40-621
40-701
40-714
A015 Battery negative ter- 40-596 40-1330
minal 40-621
40-637
40-641
40-665
40-671
40-750
40-755
40-758
40-807
40-915
40-942
40-976
40-1024
40-1099
40-1130
40-791
40-877
40-889
40-1076
40-1145
40-1166
40-1237
40-701
40-714
40-723
40-738
40-1247
40-1255

40-13
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A016 Battery negative ter- 40-596 40-1330
minal 40-621
40-637
40-641
40-665
40-671
40-750
40-755
40-758
40-807
40-915
40-942
40-976
40-1024
40-1099
40-1130
40-791
40-877
40-889
40-1076
40-1145
40-1166
40-1237
40-701
40-714
40-723
40-738
40-1247
40-1255
A017 Battery positive ter- 40-723 40-1327
minal 40-738
40-791
40-807
A018 Starter motor “+50”a 40-596 40-1327
40-621
40-807

40-14
Wiring diagrams
USA version
Table 80
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-604 40-1290
40-629
40-705
40-719
40-719
A002 04258670 Preheating device 40-604 40-1290
40-629
40-705
40-719
40-719
A003 01182961 Alternator “B+” 40-728 40-1324
40-743
40-826
40-843
A004 01182961 Alternator “D+” 40-728 40-1324
40-743
40-826
40-843
A005 01182961 Alternator “W” 40-728 40-1324
40-743
40-826
40-843
A006 Starter motor “+50” 40-604 40-1324
40-629
40-843
A007 Battery positive ter- 40-728 40-1324
minal 40-743
40-826
40-843
A008 01182961 Alternator “B+” 40-728 40-1327
40-743
40-826
40-843
A009 01182961 Alternator “D+” 40-728 40-1327
40-743
40-826
40-843
A010 01182961 Alternator “W” 40-728 40-1327
40-743
40-826
40-843
A011 +30 Battery 40-647 40-1295
40-652
40-683
40-677
40-764
40-769
40-772
40-843
40-928
40-953
40-992
40-1042
40-1110
40-1137

40-15
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A012 +30 Battery 40-647 40-1295
40-652
40-683
40-677
40-764
40-769
40-772
40-843
40-928
40-953
40-992
40-1042
40-1110
40-1137
40-826
40-882
40-895
40-1087
40-1186
40-1206
40-1240
A013 +30 Battery 40-604 40-1295
40-629
40-647
40-652
40-683
40-677
40-764
40-769
40-772
40-843
40-928
40-953
40-992
40-1042
40-1110
40-1137
40-826
40-882
40-895
40-1087
40-1186
40-1206
40-1240
40-705
40-719
40-728
40-743
40-1247
40-1255
A014 Battery positive ter- 40-604 40-1329
minal 40-629
40-705
40-719

40-16
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A015 Battery negative ter- 40-604 40-1330
minal 40-629
40-647
40-652
40-683
40-677
40-764
40-769
40-772
40-843
40-928
40-953
40-992
40-1042
40-1110
40-1137
40-826
40-882
40-895
40-1087
40-1186
40-1206
40-1240
40-705
40-719
40-728
40-743
40-1247
40-1255
A016 Battery negative ter- 40-604 40-1330
minal 40-629
40-647
40-652
40-683
40-677
40-764
40-769
40-772
40-843
40-928
40-953
40-992
40-1042
40-1110
40-1137
40-826
40-882
40-895
40-1087
40-1186
40-1206
40-1240
40-705
40-719
40-728
40-743
40-1247
40-1255
A017 Battery positive ter- 40-728 40-1327
minal 40-743
40-826
40-843

40-17
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A018 Starter motor “+50”a 40-604 40-1327
40-629
40-843

40.2.3 - A - Starting and charging (AGROFARM 430 -> ZKDW430200TD25001)

ITA version
Table 81
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-596 40-1290
40-613
40-613
40-701
A002 04258670 Preheating device 40-596 40-1290
40-613
40-613
40-701
A003 01182961 Alternator “B+” 40-723 40-1324
40-862
40-791
A004 01182961 Alternator “D+” 40-723 40-1324
40-862
40-791
A005 01182961 Alternator “W” 40-723 40-1324
40-862
40-791
A006 Starter motor “+50” 40-596 40-1324
40-613
A007 Battery positive ter- 40-723 40-1324
minal 40-862
40-791
A008 01182961 Alternator “B+” 40-723 40-1327
40-862
40-791
A009 01182961 Alternator “D+” 40-723 40-1327
40-862
40-791
A010 01182961 Alternator “W” 40-723 40-1327
40-862
40-791

40-18
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A011 +30 Battery 40-637 40-1295
40-1120
40-1059
40-1008
40-787
40-778
40-783
40-689
40-695
40-660
40-657
40-641
40-665
40-671
40-750
40-755
40-758
40-915
40-964
40-976
40-1024
40-1099
[LNK]
A012 +30 Battery 40-637 40-1295
40-1120
40-1262
40-1226
40-1059
40-1008
40-902
40-1243
40-1269
40-862
40-787
40-778
40-783
40-689
40-695
40-660
40-657
40-641
40-665
40-671
40-750
40-755
40-758
40-915
40-964
40-976
40-1024
40-1099
[LNK]
40-791
40-877
40-889
40-1145
40-1237

40-19
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A013 +30 Battery 40-596 40-1295
40-1120
40-1226
40-1059
40-1008
40-902
40-1243
40-1269
40-862
40-787
40-778
40-783
40-710
40-734
40-689
40-695
40-660
40-657
40-613
40-637
40-641
40-665
40-671
40-750
40-755
40-758
40-915
40-964
40-976
40-1024
40-1099
[LNK]
40-791
40-877
40-889
40-1145
40-1237
40-701
40-723
40-1247
40-1262
A014 Battery positive ter- 40-596 40-1329
minal 40-613
40-701

40-20
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A015 Battery negative ter- 40-596 40-1330
minal 40-1120
40-1226
40-1059
40-1008
40-902
40-1243
40-1269
40-862
40-787
40-778
40-783
40-710
40-734
40-689
40-695
40-660
40-657
40-613
40-637
40-641
40-665
40-671
40-750
40-755
40-758
40-915
40-964
40-976
40-1024
40-1099
[LNK]
40-791
40-877
40-889
40-1145
40-1237
40-701
40-723
40-1247
40-1262

40-21
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A016 Battery negative ter- 40-596 40-1330
minal 40-1120
40-1226
40-1059
40-1008
40-902
40-1243
40-1269
40-862
40-787
40-778
40-783
40-710
40-734
40-689
40-695
40-660
40-657
40-613
40-637
40-641
40-665
40-671
40-750
40-755
40-758
40-915
40-964
40-976
40-1024
40-1099
[LNK]
40-791
40-877
40-889
40-1145
40-1237
40-701
40-723
40-1247
40-1262
A017 Battery positive ter- 40-723 40-1327
minal 40-862
40-791
A018 Starter motor “+50”a 40-596 40-1327
40-613

40-22
Wiring diagrams
USA version
Table 82
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-604 40-1290
40-613
40-613
40-705
A002 04258670 Preheating device 40-604 40-1290
40-613
40-613
40-705
A003 01182961 Alternator “B+” 40-728 40-1324
40-862
40-826
A004 01182961 Alternator “D+” 40-728 40-1324
40-862
40-826
A005 01182961 Alternator “W” 40-728 40-1324
40-862
40-826
A006 Starter motor “+50” 40-604 40-1324
40-613
A007 Battery positive ter- 40-728 40-1324
minal 40-862
40-826
A008 01182961 Alternator “B+” 40-728 40-1327
40-862
40-826
A009 01182961 Alternator “D+” 40-728 40-1327
40-862
40-826
A010 01182961 Alternator “W” 40-728 40-1327
40-862
40-826
A011 +30 Battery 40-647 40-1295
40-1120
40-1059
40-1008
40-787
40-778
40-783
40-689
40-695
40-660
40-657
40-652
40-683
40-677
40-764
40-769
40-772
40-928
40-964
40-992
40-1042
40-1110
[LNK]

40-23
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A012 +30 Battery 40-647 40-1295
40-1120
40-1262
40-1059
40-1008
40-902
40-1243
40-1269
40-862
40-787
40-778
40-783
40-689
40-695
40-660
40-657
40-652
40-683
40-677
40-764
40-769
40-772
40-928
40-964
40-992
40-1042
40-1110
[LNK]
40-826
40-882
40-895
40-1186
40-1226
40-1240

40-24
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A013 +30 Battery 40-604 40-1295
40-1120
40-1059
40-1008
40-902
40-1243
40-1269
40-862
40-787
40-778
40-783
40-710
40-734
40-689
40-695
40-660
40-657
40-613
40-647
40-652
40-683
40-677
40-764
40-769
40-772
40-928
40-964
40-992
40-1042
40-1110
[LNK]
40-826
40-882
40-895
40-1186
40-1226
40-1240
40-705
40-728
40-1247
40-1262
A014 Battery positive ter- 40-604 40-1329
minal 40-613
40-705

40-25
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A015 Battery negative ter- 40-604 40-1330
minal 40-1120
40-1059
40-1008
40-902
40-1243
40-1269
40-862
40-787
40-778
40-783
40-710
40-734
40-689
40-695
40-660
40-657
40-613
40-647
40-652
40-683
40-677
40-764
40-769
40-772
40-928
40-964
40-992
40-1042
40-1110
[LNK]
40-826
40-882
40-895
40-1186
40-1226
40-1240
40-705
40-728
40-1247
40-1262

40-26
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A016 Battery negative ter- 40-604 40-1330
minal 40-1120
40-1059
40-1008
40-902
40-1243
40-1269
40-862
40-787
40-778
40-783
40-710
40-734
40-689
40-695
40-660
40-657
40-613
40-647
40-652
40-683
40-677
40-764
40-769
40-772
40-928
40-964
40-992
40-1042
40-1110
[LNK]
40-826
40-882
40-895
40-1186
40-1226
40-1240
40-705
40-728
40-1247
40-1262
A017 Battery positive ter- 40-728 40-1327
minal 40-862
40-826
A018 Starter motor “+50”a 40-604 40-1327
40-613

40-27
 Wiring diagrams
40.2.4 - A - Starting and charging (AGROFARM 410 -> ZKDW470200TD30001)
ITA version
Table 83
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-600 40-1290
40-613
40-625
40-701
40-714
40-719
A002 04258670 Preheating device 40-600 40-1290
40-613
40-625
40-701
40-714
40-719
A003 01182961 Alternator “B+” 40-723 40-1324
40-738
40-799
40-816
A004 01182961 Alternator “D+” 40-723 40-1324
40-738
40-799
40-816
A005 01182961 Alternator “W” 40-723 40-1324
40-738
40-799
40-816
A006 Starter motor “+50” 40-600 40-1324
40-625
40-816
A007 Battery positive ter- 40-723 40-1324
minal 40-738
40-799
40-816
A008 01182961 Alternator “B+” 40-723 40-1327
40-738
40-799
40-816
A009 01182961 Alternator “D+” 40-723 40-1327
40-738
40-799
40-816
A010 01182961 Alternator “W” 40-723 40-1327
40-738
40-799
40-816
A011 +30 Battery 40-637 40-1295
40-665
40-671
40-750
40-755
40-816
40-922
40-948
40-984
40-1033
40-1105
40-1133

40-28
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A012 +30 Battery 40-637 40-1295
40-665
40-671
40-750
40-755
40-816
40-922
40-948
40-984
40-1033
40-1105
40-1133
40-799
40-877
40-889
40-1082
40-1151
40-1171
40-1237
A013 +30 Battery 40-600 40-1295
40-625
40-637
40-665
40-671
40-750
40-755
40-816
40-922
40-948
40-984
40-1033
40-1105
40-1133
40-799
40-877
40-889
40-1082
40-1151
40-1171
40-1237
40-701
40-714
40-723
40-738
40-1250
40-1258
A014 Battery positive ter- 40-600 40-1329
minal 40-625
40-701
40-714

40-29
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A015 Battery negative ter- 40-600 40-1330
minal 40-625
40-637
40-665
40-671
40-750
40-755
40-816
40-922
40-948
40-984
40-1033
40-1105
40-1133
40-799
40-877
40-889
40-1082
40-1151
40-1171
40-1237
40-701
40-714
40-723
40-738
40-1250
40-1258
A016 Battery negative ter- 40-600 40-1330
minal 40-625
40-637
40-665
40-671
40-750
40-755
40-816
40-922
40-948
40-984
40-1033
40-1105
40-1133
40-799
40-877
40-889
40-1082
40-1151
40-1171
40-1237
40-701
40-714
40-723
40-738
40-1250
40-1258
A017 Battery positive ter- 40-723 40-1327
minal 40-738
40-799
40-816
A018 Starter motor “+50”a 40-600 40-1327
40-625
40-816

40-30
Wiring diagrams
USA version
Table 84
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-608 40-1290
40-613
40-633
40-705
40-719
40-719
A002 04258670 Preheating device 40-608 40-1290
40-613
40-633
40-705
40-719
40-719
A003 01182961 Alternator “B+” 40-728 40-1324
40-743
40-834
40-852
A004 01182961 Alternator “D+” 40-728 40-1324
40-743
40-834
40-852
A005 01182961 Alternator “W” 40-728 40-1324
40-743
40-834
40-852
A006 Starter motor “+50” 40-608 40-1324
40-633
40-852
A007 Battery positive ter- 40-728 40-1324
minal 40-743
40-834
40-852
A008 01182961 Alternator “B+” 40-728 40-1327
40-743
40-834
40-852
A009 01182961 Alternator “D+” 40-728 40-1327
40-743
40-834
40-852
A010 01182961 Alternator “W” 40-728 40-1327
40-743
40-834
40-852
A011 +30 Battery 40-647 40-1295
40-683
40-677
40-764
40-769
40-852
40-935
40-959
40-1001
40-1050
40-1115
40-1141

40-31
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A012 +30 Battery 40-647 40-1295
40-683
40-677
40-764
40-769
40-852
40-935
40-959
40-1001
40-1050
40-1115
40-1141
40-834
40-882
40-895
40-1093
40-1192
40-1211
40-1240
A013 +30 Battery 40-608 40-1295
40-633
40-647
40-683
40-677
40-764
40-769
40-852
40-935
40-959
40-1001
40-1050
40-1115
40-1141
40-834
40-882
40-895
40-1093
40-1192
40-1211
40-1240
40-705
40-719
40-728
40-743
40-1250
40-1258
A014 Battery positive ter- 40-608 40-1329
minal 40-633
40-705
40-719

40-32
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A015 Battery negative ter- 40-608 40-1330
minal 40-633
40-647
40-683
40-677
40-764
40-769
40-852
40-935
40-959
40-1001
40-1050
40-1115
40-1141
40-834
40-882
40-895
40-1093
40-1192
40-1211
40-1240
40-705
40-719
40-728
40-743
40-1250
40-1258
A016 Battery negative ter- 40-608 40-1330
minal 40-633
40-647
40-683
40-677
40-764
40-769
40-852
40-935
40-959
40-1001
40-1050
40-1115
40-1141
40-834
40-882
40-895
40-1093
40-1192
40-1211
40-1240
40-705
40-719
40-728
40-743
40-1250
40-1258
A017 Battery positive ter- 40-728 40-1327
minal 40-743
40-834
40-852
A018 Starter motor “+50”a 40-608 40-1327
40-633
40-852

40-33
 Wiring diagrams
40.2.5 - A - Starting and charging (AGROFARM 420 -> ZKDW510200TD30001)
ITA version
Table 85
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-600 40-1290
40-613
40-625
40-701
40-714
40-719
A002 04258670 Preheating device 40-600 40-1290
40-613
40-625
40-701
40-714
40-719
A003 01182961 Alternator “B+” 40-723 40-1324
40-738
40-799
40-816
A004 01182961 Alternator “D+” 40-723 40-1324
40-738
40-799
40-816
A005 01182961 Alternator “W” 40-723 40-1324
40-738
40-799
40-816
A006 Starter motor “+50” 40-600 40-1324
40-625
40-816
A007 Battery positive ter- 40-723 40-1324
minal 40-738
40-799
40-816
A008 01182961 Alternator “B+” 40-723 40-1327
40-738
40-799
40-816
A009 01182961 Alternator “D+” 40-723 40-1327
40-738
40-799
40-816
A010 01182961 Alternator “W” 40-723 40-1327
40-738
40-799
40-816
A011 +30 Battery 40-637 40-1295
40-665
40-671
40-750
40-755
40-816
40-922
40-948
40-984
40-1033
40-1105
40-1133

40-34
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A012 +30 Battery 40-637 40-1295
40-665
40-671
40-750
40-755
40-816
40-922
40-948
40-984
40-1033
40-1105
40-1133
40-799
40-877
40-889
40-1082
40-1158
40-1178
40-1237
A013 +30 Battery 40-600 40-1295
40-625
40-637
40-665
40-671
40-750
40-755
40-816
40-922
40-948
40-984
40-1033
40-1105
40-1133
40-799
40-877
40-889
40-1082
40-1158
40-1178
40-1237
40-701
40-714
40-723
40-738
40-1250
40-1258
A014 Battery positive ter- 40-600 40-1329
minal 40-625
40-701
40-714

40-35
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A015 Battery negative ter- 40-600 40-1330
minal 40-625
40-637
40-665
40-671
40-750
40-755
40-816
40-922
40-948
40-984
40-1033
40-1105
40-1133
40-799
40-877
40-889
40-1082
40-1158
40-1178
40-1237
40-701
40-714
40-723
40-738
40-1250
40-1258
A016 Battery negative ter- 40-600 40-1330
minal 40-625
40-637
40-665
40-671
40-750
40-755
40-816
40-922
40-948
40-984
40-1033
40-1105
40-1133
40-799
40-877
40-889
40-1082
40-1158
40-1178
40-1237
40-701
40-714
40-723
40-738
40-1250
40-1258
A017 Battery positive ter- 40-723 40-1327
minal 40-738
40-799
40-816
A018 Starter motor “+50”a 40-600 40-1327
40-625
40-816

40-36
Wiring diagrams
USA version
Table 86
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-608 40-1290
40-613
40-633
40-705
40-719
40-719
A002 04258670 Preheating device 40-608 40-1290
40-613
40-633
40-705
40-719
40-719
A003 01182961 Alternator “B+” 40-728 40-1324
40-743
40-834
40-852
A004 01182961 Alternator “D+” 40-728 40-1324
40-743
40-834
40-852
A005 01182961 Alternator “W” 40-728 40-1324
40-743
40-834
40-852
A006 Starter motor “+50” 40-608 40-1324
40-633
40-852
A007 Battery positive ter- 40-728 40-1324
minal 40-743
40-834
40-852
A008 01182961 Alternator “B+” 40-728 40-1327
40-743
40-834
40-852
A009 01182961 Alternator “D+” 40-728 40-1327
40-743
40-834
40-852
A010 01182961 Alternator “W” 40-728 40-1327
40-743
40-834
40-852
A011 +30 Battery 40-647 40-1295
40-683
40-677
40-764
40-769
40-852
40-935
40-959
40-1001
40-1050
40-1115
40-1141

40-37
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A012 +30 Battery 40-647 40-1295
40-683
40-677
40-764
40-769
40-852
40-935
40-959
40-1001
40-1050
40-1115
40-1141
40-834
40-882
40-895
40-1093
40-1199
40-1218
40-1240
A013 +30 Battery 40-608 40-1295
40-633
40-647
40-683
40-677
40-764
40-769
40-852
40-935
40-959
40-1001
40-1050
40-1115
40-1141
40-834
40-882
40-895
40-1093
40-1199
40-1218
40-1240
40-705
40-719
40-728
40-743
40-1250
40-1258
A014 Battery positive ter- 40-608 40-1329
minal 40-633
40-705
40-719

40-38
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A015 Battery negative ter- 40-608 40-1330
minal 40-633
40-647
40-683
40-677
40-764
40-769
40-852
40-935
40-959
40-1001
40-1050
40-1115
40-1141
40-834
40-882
40-895
40-1093
40-1199
40-1218
40-1240
40-705
40-719
40-728
40-743
40-1250
40-1258
A016 Battery negative ter- 40-608 40-1330
minal 40-633
40-647
40-683
40-677
40-764
40-769
40-852
40-935
40-959
40-1001
40-1050
40-1115
40-1141
40-834
40-882
40-895
40-1093
40-1199
40-1218
40-1240
40-705
40-719
40-728
40-743
40-1250
40-1258
A017 Battery positive ter- 40-728 40-1327
minal 40-743
40-834
40-852
A018 Starter motor “+50”a 40-608 40-1327
40-633
40-852

40-39
 Wiring diagrams
40.2.6 - A - Starting and charging (AGROFARM 430 -> ZKDW550200TD30001)
ITA version
Table 87
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-600 40-1290
40-616
40-616
40-701
A002 04258670 Preheating device 40-600 40-1290
40-616
40-616
40-701
A003 01182961 Alternator “B+” 40-723 40-1324
40-870
40-799
A004 01182961 Alternator “D+” 40-723 40-1324
40-870
40-799
A005 01182961 Alternator “W” 40-723 40-1324
40-870
40-799
A006 Starter motor “+50” 40-600 40-1324
40-616
A007 Battery positive ter- 40-723 40-1324
minal 40-870
40-799
A008 01182961 Alternator “B+” 40-723 40-1327
40-870
40-799
A009 01182961 Alternator “D+” 40-723 40-1327
40-870
40-799
A010 01182961 Alternator “W” 40-723 40-1327
40-870
40-799
A011 +30 Battery 40-637 40-1295
40-1125
40-1067
40-1016
40-778
40-783
40-689
40-695
40-657
40-665
40-671
40-750
40-755
40-922
40-970
40-984
40-1033
40-1105
[LNK]

40-40
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A012 +30 Battery 40-637 40-1295
40-1125
40-1266
40-1231
40-1067
40-1016
40-902
40-1243
40-1269
40-870
40-778
40-783
40-689
40-695
40-657
40-665
40-671
40-750
40-755
40-922
40-970
40-984
40-1033
40-1105
[LNK]
40-799
40-877
40-889
40-1158
40-1237

40-41
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A013 +30 Battery 40-600 40-1295
40-1125
40-1231
40-1067
40-1016
40-902
40-1243
40-1269
40-870
40-778
40-783
40-710
40-734
40-689
40-695
40-657
40-616
40-637
40-665
40-671
40-750
40-755
40-922
40-970
40-984
40-1033
40-1105
[LNK]
40-799
40-877
40-889
40-1158
40-1237
40-701
40-723
40-1250
40-1266
A014 Battery positive ter- 40-600 40-1329
minal 40-616
40-701

40-42
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A015 Battery negative ter- 40-600 40-1330
minal 40-1125
40-1231
40-1067
40-1016
40-902
40-1243
40-1269
40-870
40-778
40-783
40-710
40-734
40-689
40-695
40-657
40-616
40-637
40-665
40-671
40-750
40-755
40-922
40-970
40-984
40-1033
40-1105
[LNK]
40-799
40-877
40-889
40-1158
40-1237
40-701
40-723
40-1250
40-1266

40-43
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A016 Battery negative ter- 40-600 40-1330
minal 40-1125
40-1231
40-1067
40-1016
40-902
40-1243
40-1269
40-870
40-778
40-783
40-710
40-734
40-689
40-695
40-657
40-616
40-637
40-665
40-671
40-750
40-755
40-922
40-970
40-984
40-1033
40-1105
[LNK]
40-799
40-877
40-889
40-1158
40-1237
40-701
40-723
40-1250
40-1266
A017 Battery positive ter- 40-723 40-1327
minal 40-870
40-799
A018 Starter motor “+50”a 40-600 40-1327
40-616

40-44
Wiring diagrams
USA version
Table 88
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A001 +30 Battery 40-608 40-1290
40-616
40-616
40-705
A002 04258670 Preheating device 40-608 40-1290
40-616
40-616
40-705
A003 01182961 Alternator “B+” 40-728 40-1324
40-870
40-834
A004 01182961 Alternator “D+” 40-728 40-1324
40-870
40-834
A005 01182961 Alternator “W” 40-728 40-1324
40-870
40-834
A006 Starter motor “+50” 40-608 40-1324
40-616
A007 Battery positive ter- 40-728 40-1324
minal 40-870
40-834
A008 01182961 Alternator “B+” 40-728 40-1327
40-870
40-834
A009 01182961 Alternator “D+” 40-728 40-1327
40-870
40-834
A010 01182961 Alternator “W” 40-728 40-1327
40-870
40-834
A011 +30 Battery 40-647 40-1295
40-1125
40-1067
40-1016
40-778
40-783
40-689
40-695
40-657
40-683
40-677
40-764
40-769
40-935
40-970
40-1001
40-1050
40-1115
[LNK]

40-45
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A012 +30 Battery 40-647 40-1295
40-1125
40-1266
40-1067
40-1016
40-902
40-1243
40-1269
40-870
40-778
40-783
40-689
40-695
40-657
40-683
40-677
40-764
40-769
40-935
40-970
40-1001
40-1050
40-1115
[LNK]
40-834
40-882
40-895
40-1199
40-1231
40-1240

40-46
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A013 +30 Battery 40-608 40-1295
40-1125
40-1067
40-1016
40-902
40-1243
40-1269
40-870
40-778
40-783
40-710
40-734
40-689
40-695
40-657
40-616
40-647
40-683
40-677
40-764
40-769
40-935
40-970
40-1001
40-1050
40-1115
[LNK]
40-834
40-882
40-895
40-1199
40-1231
40-1240
40-705
40-728
40-1250
40-1266
A014 Battery positive ter- 40-608 40-1329
minal 40-616
40-705

40-47
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A015 Battery negative ter- 40-608 40-1330
minal 40-1125
40-1067
40-1016
40-902
40-1243
40-1269
40-870
40-778
40-783
40-710
40-734
40-689
40-695
40-657
40-616
40-647
40-683
40-677
40-764
40-769
40-935
40-970
40-1001
40-1050
40-1115
[LNK]
40-834
40-882
40-895
40-1199
40-1231
40-1240
40-705
40-728
40-1250
40-1266

40-48
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
A016 Battery negative ter- 40-608 40-1330
minal 40-1125
40-1067
40-1016
40-902
40-1243
40-1269
40-870
40-778
40-783
40-710
40-734
40-689
40-695
40-657
40-616
40-647
40-683
40-677
40-764
40-769
40-935
40-970
40-1001
40-1050
40-1115
[LNK]
40-834
40-882
40-895
40-1199
40-1231
40-1240
40-705
40-728
40-1250
40-1266
A017 Battery positive ter- 40-728 40-1327
minal 40-870
40-834
A018 Starter motor “+50”a 40-608 40-1327
40-616

40-49
 Wiring diagrams
40.2.7 - B - Fuses (AGROFARM 410 -> ZKDW350200TD25001)
ITA version

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1072 - Fuse box, cab version

l Ba001 - Air conditioning compressor fuse (10A)
l Ba002 - Trailer brake lights fuse (key-on power) (7.5A)
l Ba003 - Emergency fuse (direct) (20A)
l Ba004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Ba005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Ba006 - Instrument panel fuse (direct) (5A)
l Ba007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Ba008 +30 cluster fuse (3A)
l Ba009 +30 Wolp fuse (10A)
l Ba010 - Ancillary fuse (lift) (15A)
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba012 - Socket fuse (key-on power) (7.5A)
l Ba013 - Front loader fuse (key-on power) (7.5A)
l Ba014 - Fuse for work lights on cab (key-on power) (15A)
l Ba015 - Fuse for low work lights (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba017 - Instrument panel fuse (key-on power) (10A)
l Ba018 - Engine ECU fuse (key-on power) (7.5A)
l Ba019 - RH sidelights fuse (7.5A)
l Ba020 - LH sidelights fuse (7.5A)
l Ba021 - MK1 relay fuse 30A
l Ba022 - Protection fuse, FT 5-6-7-8 (30A)

40-50
Wiring diagrams

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1072 - Fuse box, cab version

l Ba023 - Fan/compressor fuse (30A)
l Ba024 - Starter fuse (40A)
l Ba025 - Protection fuse (40A)
l Ba026 - MK3 relay fuse 30A
l Ba027 - Distributor 7-8 fuse (5A)
l Ba028 - Power socket fuse (key-on power) (30A)
l Ba029 - Not used
l Ba030 - Steering column stalk fuse - lights input (20A)
l Ba031 - Ventilation/heating fuse (20A)

40-51
 Wiring diagrams

Bd026 Bd029

Bd022

Bd023
Bd021
Bd027 Bd030

Bd028 Bd031
Bd020

Bd019

Bd018

Bd017

Bd016

Bd015

Bd014

Bd013

Bd012

Bd011
Bd001

Bd002

Bd003

Bd004

Bd005

Bd006

Bd007

Bd008

Bd009

Bd010

Fig. 1073 - Fuse box, platform version

l Bd001 - Air conditioning compressor fuse (10A)
l Bd002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bd003 - Emergency fuse (direct) (20A)
l Bd004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bd005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bd006 - Instrument panel fuse (direct) (5A)
l Bd007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bd008 - Cluster fuse +30 (3A)
l Bd009 - Wolp fuse +30 (10A)
l Bd010 - Ancillary fuse (lift) (15A)
l Bd011 - Turn indicator lights fuse (key-on power) (15A)
l Bd012 - Socket fuse (key-on power) (7.5A)
l Bd013 - Front loader fuse (key-on power) (7.5A)
l Bd014 - Fuse for work lights on cab (key-on power) (15A)
l Bd015 - Fuse for low work lights (key-on power) (15A)
l Bd016 - Relay fuse (key-on power) (3A)
l Bd017 - Instrument panel fuse (key-on power) (10A)
l Bd018 - Engine ECU fuse (key-on power) (7.5A)
l Bd019 - RH sidelights fuse (7.5A)
l Bd020 - LH sidelights fuse (7.5A)
l Bd021 - MK1 relay fuse 30A
l Bd022 - Protection fuse, FT 5-6-7-8 (30A)
l Bd023 - Fan/compressor fuse (30A)
l Bd024 - Starter fuse (40A)
l Bd025 - Protection fuse (40A)

40-52
Wiring diagrams

Bd026 Bd029

Bd022

Bd023
Bd021
Bd027 Bd030

Bd028 Bd031
Bd020

Bd019

Bd018

Bd017

Bd016

Bd015

Bd014

Bd013

Bd012

Bd011
Bd001

Bd002

Bd003

Bd004

Bd005

Bd006

Bd007

Bd008

Bd009

Bd010

Fig. 1073 - Fuse box, platform version

l Bd026 - MK3 relay fuse 30A
l Bd027 - Distributor 7-8 fuse (5A)
l Bd028 - Power socket fuse (30A)
l Bd029 - Not used
l Bd030 - Steering column stalk fuse - lights input (20A)
l Bd031 - Ventilation/heating fuse (20A)

40-53
 Wiring diagrams
Table 89
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-596 40-1295
40-1255
40-1247
40-1166
40-1145
40-1076
40-1024
40-976
40-942
40-915
40-889
40-877
40-807
40-791
40-758
40-755
40-750
40-738
40-723
40-714
40-701
40-671
40-665
40-621
40-641
40-637
B002 Preheat fuse 125A 40-596 40-1290
40-714
40-701
40-621
B003 0.900.0783.1 60A fuse 40-637 40-1295
40-1099
40-1024
40-976
40-807
40-758
40-755
40-750
40-671
40-665
40-641

40-54
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B004 0.900.0783.1 60A fuse 40-637 40-1295
40-1166
40-1145
40-1130
40-1099
40-1076
40-1024
40-976
40-942
40-915
40-889
40-877
40-807
40-791
40-758
40-755
40-750
40-671
40-665
40-641
Ba001 Air conditioning com- 40-665 40-1331
pressor fuse (10A) 40-671
Ba002 Trailer brake lights 40-791 40-1331
fuse (key-on power) 40-877
(7.5A)
Ba003 Emergency fuse (di- 40-915 40-1331
rect) (20A)
Ba004 Seat compressor / 40-1099 40-1331
cigarette lighter fuse
(direct) (15A)
Ba005 Brake lights fuse 40-877 40-1331
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Ba006 Instrument panel 40-791 40-1331
fuse (direct) (5A) 40-1247
Ba007 Hydraulic reverse 40-791 40-1331
shuttle fuse (direct) 40-1247
(7.5A) 40-1145
Ba008 Low beam head- 40-915 40-1331
lights fuse (15A)
Ba009 High beam head- 40-915 40-1331
lights fuse (15A)
Ba010 Ancillary fuse (lift) [LNK] 40-1331
(15A)
Ba011 Turn indicator lights 40-637 40-1331
fuse (key-on power) 40-1024
(15A) 40-976
40-915
40-877
40-758
40-755
40-750
40-671
40-665
40-641

40-55
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba012 Socket fuse (key-on [LNK] 40-1331
power) (7.5A)
Ba013 Front loader fuse [LNK] 40-1331
(key-on power)
(7.5A)
Ba014 Fuse for work lights 40-976 40-1331
on cab (key-on pow- 40-1024
er) (15A)
Ba015 Fuse for low work 40-976 40-1331
lights (key-on power) 40-1024
(15A)
Ba016 Relay fuse (key-on 40-637 40-1331
power) (3A) 40-1145
40-1024
40-976
40-915
40-877
40-791
40-758
40-755
40-750
40-671
40-665
40-641
Ba017 Instrument panel 40-596 40-1331
fuse (key-on power) 40-1247
(10A) 40-1145
40-915
40-877
40-791
40-723
40-701
40-621
Ba018 Engine ECU fuse 40-596 40-1331
(key-on power) 40-1247
(7.5A) 40-1145
40-791
40-701
40-621
Ba019 RH sidelights fuse 40-915 40-1331
(7.5A)
Ba020 LH sidelights fuse 40-915 40-1331
(7.5A)
Ba021 MK1 relay fuse 30A 40-791 40-1331
40-1145
40-1024
40-976
40-877
Ba022 Protection fuse, FT 40-750 40-1331
5-6-7-8 (30A) 40-1024
40-976
40-758
40-755
Ba023 Fan/compressor 40-637 40-1331
fuse (30 A) 40-671
40-665
40-641

40-56
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba024 Starter fuse (40A) 40-596 40-1331
40-1145
40-701
40-621
Ba025 Protection fuse 40-665 40-1331
(40A) 40-1099
40-1024
40-750
40-671
Ba026 MK3 relay fuse 30A 40-637 40-1331
40-1024
40-976
40-915
40-877
40-758
40-755
40-671
40-665
40-641
Ba027 Distributor 7-8 fuse [LNK] 40-1331
(5A)
Ba028 Power socket fuse [LNK] 40-1331
(30A)
Ba029 Not used [LNK] 40-1331
Ba030 Steering column 40-915 40-1331
stalk fuse - lights in- 40-1099
put (20A)
Ba031 Ventilation/heating 40-637 40-1331
fuse (20A) 40-671
40-665
40-641

Table 90
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bd001 Air conditioning com- [LNK] 40-1392
pressor fuse (10A)
Bd002 Trailer brake lights 40-807 40-1392
fuse (key-on power) 40-1166
(7.5A) 40-889
Bd003 Emergency fuse (di- 40-942 40-1392
rect) (20A)
Bd004 Seat compressor / 40-1130 40-1392
cigarette lighter fuse
(direct) (15A)
Bd005 Brake lights fuse [LNK] 40-1392
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bd006 Instrument panel 40-807 40-1392
fuse (direct) (5A) 40-1255
40-889
Bd007 Hydraulic reverse 40-807 40-1392
shuttle fuse (direct) 40-1255
(7.5A) 40-1166
Bd008 Low beam head- 40-942 40-1392
lights fuse (15A)

40-57
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bd009 High beam head- [LNK] 40-1392
lights fuse (15A)
Bd010 Ancillary fuse (lift) 40-1076 40-1392
(15A)
Bd011 Turn indicator lights 40-889 40-1392
fuse (key-on power)
(15A)
Bd012 Socket fuse (key-on [LNK] 40-1392
power) (7.5A)
Bd013 Front loader fuse [LNK] 40-1392
(key-on power)
(7.5A)
Bd014 Fuse for work lights 40-1076 40-1392
on cab (key-on pow-
er) (15A)
Bd015 Fuse for low work 40-1076 40-1392
lights (key-on power)
(15A)
Bd016 Relay fuse (key-on 40-807 40-1392
power) (3A) 40-1166
40-1076
40-942
40-889
Bd017 Instrument panel 40-714 40-1392
fuse (key-on power) 40-1255
(10A) 40-1166
40-942
40-889
40-807
40-738
Bd018 Engine ECU fuse 40-714 40-1392
(key-on power) 40-1255
(7.5A) 40-1166
40-807
Bd019 RH sidelights fuse 40-942 40-1392
(7.5A)
Bd020 LH sidelights fuse 40-942 40-1392
(7.5A)
Bd021 MK1 relay fuse 30A 40-807 40-1392
40-1166
40-1076
40-889
Bd022 Protection fuse, FT 40-1166 40-1392
5-6-7-8 (30A)
Bd023 Fan/compressor [LNK] 40-1392
fuse (30 A)
Bd024 Starter fuse (40A) 40-714 40-1392
Bd025 Protection fuse [LNK] 40-1392
(40A)
Bd026 MK3 relay fuse 30A 40-889 40-1392
40-942
Bd027 Distributor 7-8 fuse [LNK] 40-1392
(5A)
Bd028 Power socket fuse [LNK] 40-1392
(30A)
Bd029 Not used [LNK] 40-1392
Bd030 Steering column 40-942 40-1392
stalk fuse - lights in- 40-1130
put (20A)

40-58
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bd031 Ventilation/heating [LNK] 40-1392
fuse (20A)

Table 91
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1024 40-1301
(10A - Rotating bea-
con)
Be002 Fuse 2 in fuse box F 40-1099 40-1301
(5A - Radio)
Be003 Fuse 3 in fuse box F 40-671 40-1301
(30A - Climate con-
trol)
Be005 Fuse 5 in fuse box F 40-750 40-1301
(7.5A - Windscreen
wiper)
Be006 Fuse 6 in fuse box F 40-750 40-1301
(7.5A - Rear screen
wiper)
Be007 Fuse 7 in fuse box 40-1024 40-1301
F (10A - Front work
lights)
Be008 Fuse 8 in fuse box 40-1024 40-1301
F (10A - Rear work
lights)
Bf001 Fuse 1 in fuse box F 40-976 40-1318
(10A - Rotating bea-
con)
Bf002 Fuse 2 in fuse box F [LNK] 40-1318
(5A - Radio)
Bf003 Fuse 3 in fuse box F [LNK] 40-1318
(30A - Climate con-
trol)
Bf004 Not used [LNK] 40-1318
Bf005 Fuse 5 in fuse box F 40-758 40-1318
(7.5A - Windscreen
wiper)
Bf006 Fuse 6 in fuse box F 40-758 40-1318
(7.5A - Rear screen
wiper)
Bf007 Fuse 7 in fuse box 40-976 40-1318
F (10A - Front work
lights)
Bf008 Fuse 8 in fuse box 40-976 40-1318
F (10A - Rear work
lights)
Bg001 10A fuse (beacon) 40-976 40-1388
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-665 40-1388
and climate control)
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)

40-59
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bg007 10A fuse (rear work 40-976 40-1388
light)
Bg008 10A fuse (front work 40-976 40-1388
lights)
USA version

Bb026 Bb029

Bb022

Bb023
Bb021

Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1074 - Fuse box, cab version

l Bb001 - Air conditioning compressor fuse (10A)
l Bb002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bb003 - Emergency fuse (direct) (20A)
l Bb004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bb005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bb006 - Instrument panel fuse (direct) (5A)
l Bb007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bb008 - Cluster fuse +30 (3A)
l Bb009 - Wolp fuse +30 (10A)
l Bb010 - Ancillary fuse (lift) (15A)
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb012 - Socket fuse (key-on power) (7.5A)
l Bb013 - Front loader fuse (key-on power) (7.5A)
l Bb014 - Fuse for work lights on cab (key-on power) (15A)
l Bb015 - Fuse for low work lights (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)

40-60
Wiring diagrams

Bb026 Bb029

Bb022

Bb023
Bb021
Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1074 - Fuse box, cab version

l Bb017 - Instrument panel fuse (key-on power) (10A)
l Bb018 - Engine ECU fuse (key-on power) (7.5A)
l Bb019 - RH sidelights fuse (7.5A)
l Bb020 - LH sidelights fuse (7.5A)
l Bb021 - MK1 relay fuse 30A
l Bb022- Protection fuse, FT 5-6-7-8 (30A)
l Bb023 - Fan/compressor fuse (30A)
l Bb024 - Starter fuse (40A)
l Bb025 - Protection fuse (40A)
l Bb026 - MK3 relay fuse 30A
l Bb027 - Distributor 7-8 fuse (5A)
l Bb028 - Power socket fuse (30A)
l Bb029 - Not used
l Bb030 - Steering column stalk fuse - lights input (20A)
l Bb031 - Ventilation/heating fuse (20A)

40-61
 Wiring diagrams

Bh026 Bh029

Bh022

Bh023
Bh021
Bh027 Bh030

Bh028 Bh031
Bh020

Bh019

Bh018

Bh017

Bh016

Bh015

Bh014

Bh013

Bh012

Bh011
Bh001

Bh002

Bh003

Bh004

Bh005

Bh006

Bh007

Bh008

Bh009

Bh010

Fig. 1075 - Fuse box, platform version

l Bh001 - Air conditioning compressor fuse (10A)
l Bh002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bh003 - Emergency fuse (direct) (20A)
l Bh004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bh005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bh006 - Instrument panel fuse (direct) (5A)
l Bh007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bh008 - Cluster fuse +30 (3A)
l Bh009 - Wolp fuse +30 (10A)
l Bh010 - Ancillary fuse (lift) (15A)
l Bh011 - Turn indicator lights fuse (key-on power) (15A)
l Bh012 - Socket fuse (key-on power) (7.5A)
l Bh013 - Front loader fuse (key-on power) (7.5A)
l Bh014 - Fuse for work lights on cab (key-on power) (15A)
l Bh015 - Fuse for low work lights (key-on power) (15A)
l Bh016 - Relay fuse (key-on power) (3A)
l Bh017 - Instrument panel fuse (key-on power) (10A)
l Bh018 - Engine ECU fuse (key-on power) (7.5A)
l Bh019 - RH sidelights fuse (7.5A)
l Bh020 - LH sidelights fuse (7.5A)
l Bh021 - MK1 relay fuse 30A
l Bh022 - Protection fuse, FT 5-6-7-8 (30A)
l Bh023 - Fan/compressor fuse (30A)
l Bh024 - Starter fuse (40A)
l Bh025 - Protection fuse (40A)

40-62
Wiring diagrams

Bh026 Bh029

Bh022

Bh023
Bh021
Bh027 Bh030

Bh028 Bh031
Bh020

Bh019

Bh018

Bh017

Bh016

Bh015

Bh014

Bh013

Bh012

Bh011
Bh001

Bh002

Bh003

Bh004

Bh005

Bh006

Bh007

Bh008

Bh009

Bh010

Fig. 1075 - Fuse box, platform version

l Bh026 - MK3 relay fuse 30A
l Bh027 - Distributor 7-8 fuse (5A)
l Bh028 - Power socket fuse (30A)
l Bh029 - Not used
l Bh030 - Steering column stalk fuse - lights input (20A)
l Bh031 - Ventilation/heating fuse (20A)

40-63
 Wiring diagrams
Table 92
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-604 40-1295
40-1206
40-1186
40-1087
40-1042
40-992
40-953
40-928
40-895
40-882
40-764
40-769
40-772
40-743
40-728
40-719
40-705
40-683
40-677
40-652
40-647
40-629
40-1255
40-1247
40-641
B002 Preheat fuse 125A 40-604 40-1290
40-719
40-705
40-629
B003 0.900.0783.1 60A fuse 40-647 40-1295
40-1110
40-1042
40-992
40-764
40-769
40-772
40-683
40-677
40-652
40-641

40-64
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B004 0.900.0783.1 60A fuse 40-647 40-1295
40-1206
40-1186
40-1137
40-1110
40-1087
40-1042
40-992
40-953
40-928
40-895
40-882
40-843
40-826
40-764
40-769
40-772
40-683
40-677
40-652
40-641

Table 93
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb001 Air conditioning com- 40-683 40-1347
pressor fuse (10A) 40-677
Bb002 Trailer brake lights 40-882 40-1347
fuse (key-on power) 40-1186
(7.5A)
Bb003 Emergency fuse (di- 40-928 40-1347
rect) (20A)
Bb004 Seat compressor / 40-1110 40-1347
cigarette lighter fuse
(direct) (15A)
Bb005 Brake lights fuse 40-928 40-1347
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bb006 Instrument panel 40-1247 40-1347
fuse (direct) (5A) 40-826
Bb007 Hydraulic reverse 40-1247 40-1347
shuttle fuse (direct) 40-1186
(7.5A)
Bb008 Low beam head- 40-928 40-1347
lights fuse (15A)
Bb009 High beam head- 40-928 40-1347
lights fuse (15A)
Bb010 Ancillary fuse (lift) [LNK] 40-1347
(15A)

40-65
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb011 Turn indicator lights 40-647 40-1347
fuse (key-on power) 40-1042
(15A) 40-992
40-928
40-882
40-764
40-769
40-772
40-683
40-677
40-652
Bb012 Socket fuse (key-on 40-928 40-1347
power) (7.5A)
Bb013 Front loader fuse [LNK] 40-1347
(key-on power)
(7.5A)
Bb014 Fuse for work lights 40-992 40-1347
on cab (key-on pow- 40-1042
er) (15A)
Bb015 Fuse for low work 40-992 40-1347
lights (key-on power) 40-1042
(15A)
Bb016 Relay fuse (key-on 40-647 40-1347
power) (3A) 40-1186
40-1042
40-992
40-928
40-882
40-826
40-764
40-769
40-772
40-683
40-677
40-652
Bb017 Instrument panel 40-1247 40-1347
fuse (key-on power) 40-1186
(10A) 40-928
40-882
40-826
40-728
40-705
40-604
Bb018 Engine ECU fuse 40-1247 40-1347
(key-on power) 40-1186
(7.5A) 40-705
40-604
Bb019 RH sidelights fuse 40-928 40-1347
(7.5A)
Bb020 LH sidelights fuse 40-928 40-1347
(7.5A)
Bb021 MK1 relay fuse 30A 40-826 40-1347
40-1186
40-1042
40-992
40-882

40-66
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb022 Protection fuse, FT 40-764 40-1347
5-6-7-8 (30A) 40-1042
40-992
40-826
40-769
40-772
Bb023 Fan/compressor 40-647 40-1347
fuse (30 A) 40-683
40-677
40-652
Bb024 Starter fuse (40A) 40-604 40-1347
40-1186
40-705
Bb025 Protection fuse 40-683 40-1347
(40A) 40-1110
40-1042
40-992
40-677
Bb026 MK3 relay fuse 30A 40-647 40-1347
40-1042
40-992
40-928
40-882
40-764
40-769
40-772
40-683
40-677
40-652
Bb027 Distributor 7-8 fuse [LNK] 40-1347
(5A)
Bb028 Power socket fuse [LNK] 40-1347
(30A)
Bb029 Not used [LNK] 40-1347
Bb030 Steering column 40-928 40-1347
stalk fuse - lights in- 40-1110
put (20A)
Bb031 Ventilation/heating 40-647 40-1347
fuse (20A) 40-683
40-677
40-652

40-67
 Wiring diagrams
Table 94
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1042 40-1301
(10A - Rotating bea-
con)
Be002 Fuse 2 in fuse box F 40-1110 40-1301
(5A - Radio)
Be003 Fuse 3 in fuse box F 40-677 40-1301
(30A - Climate con-
trol)
Be005 Fuse 5 in fuse box F 40-764 40-1301
(7.5A - Windscreen
wiper)
Be006 Fuse 6 in fuse box F 40-764 40-1301
(7.5A - Rear screen
wiper)
Be007 Fuse 7 in fuse box 40-1042 40-1301
F (10A - Front work
lights)
Be008 Fuse 8 in fuse box 40-1042 40-1301
F (10A - Rear work
lights)
Bf001 Fuse 1 in fuse box F 40-992 40-1318
(10A - Rotating bea-
con)
Bf002 Fuse 2 in fuse box F [LNK] 40-1318
(5A - Radio)
Bf003 Fuse 3 in fuse box F [LNK] 40-1318
(30A - Climate con-
trol)
Bf004 Not used [LNK] 40-1318
Bf005 Fuse 5 in fuse box F 40-772 40-1318
(7.5A - Windscreen
wiper)
Bf006 Fuse 6 in fuse box F 40-772 40-1318
(7.5A - Rear screen
wiper)
Bf007 Fuse 7 in fuse box 40-992 40-1318
F (10A - Front work
lights)
Bf008 Fuse 8 in fuse box 40-992 40-1318
F (10A - Rear work
lights)
Bg001 10A fuse (beacon) 40-992 40-1388
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-683 40-1388
and climate control)
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)
Bg007 10A fuse (rear work 40-992 40-1388
light)
Bg008 10A fuse (front work 40-992 40-1388
lights)

40-68
Wiring diagrams
Table 95
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bh001 Air conditioning com- [LNK] 40-1410
pressor fuse (10A)
Bh002 Trailer brake lights 40-843 40-1410
fuse (key-on power) 40-1206
(7.5A) 40-895
Bh003 Emergency fuse (di- 40-843 40-1410
rect) (20A) 40-953
Bh004 Seat compressor / 40-1137 40-1410
cigarette lighter fuse
(direct) (15A)
Bh005 Brake lights fuse 40-953 40-1410
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bh006 Instrument panel 40-1255 40-1410
fuse (direct) (5A) 40-843
Bh007 Hydraulic reverse 40-1255 40-1410
shuttle fuse (direct) 40-1206
(7.5A) 40-843
Bh008 Low beam head- 40-953 40-1410
lights fuse (15A)
Bh009 High beam head- 40-953 40-1410
lights fuse (15A)
Bh010 Ancillary fuse (lift) 40-1087 40-1410
(15A)
Bh011 Turn indicator lights 40-895 40-1410
fuse (key-on power) 40-953
(15A)
Bh012 Socket fuse (key-on 40-953 40-1410
power) (7.5A)
Bh013 Front loader fuse [LNK] 40-1410
(key-on power)
(7.5A)
Bh014 Fuse for work lights 40-1087 40-1410
on cab (key-on pow-
er) (15A)
Bh015 Fuse for low work 40-1087 40-1410
lights (key-on power)
(15A)
Bh016 Relay fuse (key-on 40-843 40-1410
power) (3A) 40-1206
40-1087
40-953
40-895
Bh017 Instrument panel 40-1255 40-1410
fuse (key-on power) 40-1206
(10A) 40-953
40-895
40-843
40-743
40-719
40-629

40-69
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bh018 Engine ECU fuse 40-1255 40-1410
(key-on power) 40-1206
(7.5A) 40-843
40-719
40-629
Bh019 RH sidelights fuse 40-953 40-1410
(7.5A)
Bh020 LH sidelights fuse 40-953 40-1410
(7.5A)
Bh021 MK1 relay fuse 30A 40-843 40-1410
40-1206
40-1087
40-895
Bh022 Protection fuse, FT 40-1206 40-1410
5-6-7-8 (30A)
Bh023 Fan/compressor [LNK] 40-1410
fuse (30 A)
Bh024 Starter fuse (40A) 40-629 40-1410
40-719
Bh025 Protection fuse [LNK] 40-1410
(40A)
Bh026 MK3 relay fuse 30A 40-895 40-1410
40-953
Bh027 Distributor 7-8 fuse [LNK] 40-1410
(5A)
Bh028 Power socket fuse [LNK] 40-1410
(30A)
Bh029 Not used [LNK] 40-1410
Bh030 Steering column 40-953 40-1410
stalk fuse - lights in- 40-1137
put (20A)
Bh031 Ventilation/heating [LNK] 40-1410
fuse (20A)

40-70
Wiring diagrams
40.2.8 - B - Fuses (AGROFARM 420 -> ZKDW390200TD25001)
ITA version

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1076 - Fuse box, cab version

l Ba001 - Air conditioning compressor fuse (10A)
l Ba002 - Trailer brake lights fuse (key-on power) (7.5A)
l Ba003 - Emergency fuse (direct) (20A)
l Ba004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Ba005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Ba006 - Instrument panel fuse (direct) (5A)
l Ba007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Ba008 +30 cluster fuse (3A)
l Ba009 +30 Wolp fuse (10A)
l Ba010 - Ancillary fuse (lift) (15A)
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba012 - Socket fuse (key-on power) (7.5A)
l Ba013 - Front loader fuse (key-on power) (7.5A)
l Ba014 - Fuse for work lights on cab (key-on power) (15A)
l Ba015 - Fuse for low work lights (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba017 - Instrument panel fuse (key-on power) (10A)
l Ba018 - Engine ECU fuse (key-on power) (7.5A)
l Ba019 - RH sidelights fuse (7.5A)
l Ba020 - LH sidelights fuse (7.5A)
l Ba021 - MK1 relay fuse 30A
l Ba022 - Protection fuse, FT 5-6-7-8 (30A)

40-71
 Wiring diagrams

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1076 - Fuse box, cab version

l Ba023 - Fan/compressor fuse (30A)
l Ba024 - Starter fuse (40A)
l Ba025 - Protection fuse (40A)
l Ba026 - MK3 relay fuse 30A
l Ba027 - Distributor 7-8 fuse (5A)
l Ba028 - Power socket fuse (key-on power) (30A)
l Ba029 - Not used
l Ba030 - Steering column stalk fuse - lights input (20A)
l Ba031 - Ventilation/heating fuse (20A)

40-72
Wiring diagrams

Bd026 Bd029

Bd022

Bd023
Bd021
Bd027 Bd030

Bd028 Bd031
Bd020

Bd019

Bd018

Bd017

Bd016

Bd015

Bd014

Bd013

Bd012

Bd011
Bd001

Bd002

Bd003

Bd004

Bd005

Bd006

Bd007

Bd008

Bd009

Bd010

Fig. 1077 - Fuse box, platform version

l Bd001 - Air conditioning compressor fuse (10A)
l Bd002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bd003 - Emergency fuse (direct) (20A)
l Bd004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bd005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bd006 - Instrument panel fuse (direct) (5A)
l Bd007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bd008 - Cluster fuse +30 (3A)
l Bd009 - Wolp fuse +30 (10A)
l Bd010 - Ancillary fuse (lift) (15A)
l Bd011 - Turn indicator lights fuse (key-on power) (15A)
l Bd012 - Socket fuse (key-on power) (7.5A)
l Bd013 - Front loader fuse (key-on power) (7.5A)
l Bd014 - Fuse for work lights on cab (key-on power) (15A)
l Bd015 - Fuse for low work lights (key-on power) (15A)
l Bd016 - Relay fuse (key-on power) (3A)
l Bd017 - Instrument panel fuse (key-on power) (10A)
l Bd018 - Engine ECU fuse (key-on power) (7.5A)
l Bd019 - RH sidelights fuse (7.5A)
l Bd020 - LH sidelights fuse (7.5A)
l Bd021 - MK1 relay fuse 30A
l Bd022 - Protection fuse, FT 5-6-7-8 (30A)
l Bd023 - Fan/compressor fuse (30A)
l Bd024 - Starter fuse (40A)
l Bd025 - Protection fuse (40A)

40-73
 Wiring diagrams

Bd026 Bd029

Bd022

Bd023
Bd021
Bd027 Bd030

Bd028 Bd031
Bd020

Bd019

Bd018

Bd017

Bd016

Bd015

Bd014

Bd013

Bd012

Bd011
Bd001

Bd002

Bd003

Bd004

Bd005

Bd006

Bd007

Bd008

Bd009

Bd010

Fig. 1077 - Fuse box, platform version

l Bd026 - MK3 relay fuse 30A
l Bd027 - Distributor 7-8 fuse (5A)
l Bd028 - Power socket fuse (30A)
l Bd029 - Not used
l Bd030 - Steering column stalk fuse - lights input (20A)
l Bd031 - Ventilation/heating fuse (20A)

40-74
Wiring diagrams
Table 96
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-596 40-1295
40-1255
40-1247
40-1237
40-1166
40-1145
40-1076
40-1024
40-976
40-942
40-915
40-889
40-877
40-807
40-791
40-758
40-755
40-750
40-738
40-723
40-714
40-701
40-671
40-665
40-621
40-641
40-637
B002 Preheat fuse 125A 40-596 40-1290
40-714
40-701
40-621
B003 0.900.0783.1 60A fuse 40-637 40-1295
40-1099
40-1024
40-976
40-807
40-758
40-755
40-750
40-671
40-665
40-641

40-75
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B004 0.900.0783.1 60A fuse 40-637 40-1295
40-1237
40-1166
40-1145
40-1130
40-1099
40-1076
40-1024
40-976
40-942
40-915
40-889
40-877
40-807
40-791
40-758
40-755
40-750
40-671
40-665
40-641
Ba001 Air conditioning com- 40-665 40-1331
pressor fuse (10A) 40-671
Ba002 Trailer brake lights 40-791 40-1331
fuse (key-on power) 40-877
(7.5A)
Ba003 Emergency fuse (di- 40-915 40-1331
rect) (20A)
Ba004 Seat compressor / 40-1099 40-1331
cigarette lighter fuse
(direct) (15A)
Ba005 Brake lights fuse 40-877 40-1331
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Ba006 Instrument panel 40-791 40-1331
fuse (direct) (5A) 40-1247
Ba007 Hydraulic reverse 40-791 40-1331
shuttle fuse (direct) 40-1247
(7.5A) 40-1145
Ba008 Low beam head- 40-915 40-1331
lights fuse (15A)
Ba009 High beam head- 40-915 40-1331
lights fuse (15A)
Ba010 Ancillary fuse (lift) [LNK] 40-1331
(15A)
Ba011 Turn indicator lights 40-637 40-1331
fuse (key-on power) 40-1024
(15A) 40-976
40-915
40-877
40-758
40-755
40-750
40-671
40-665
40-641

40-76
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba012 Socket fuse (key-on [LNK] 40-1331
power) (7.5A)
Ba013 Front loader fuse [LNK] 40-1331
(key-on power)
(7.5A)
Ba014 Fuse for work lights 40-976 40-1331
on cab (key-on pow- 40-1024
er) (15A)
Ba015 Fuse for low work 40-976 40-1331
lights (key-on power) 40-1024
(15A)
Ba016 Relay fuse (key-on 40-637 40-1331
power) (3A) 40-1237
40-1145
40-1024
40-976
40-915
40-877
40-791
40-758
40-755
40-750
40-671
40-665
40-641
Ba017 Instrument panel 40-596 40-1331
fuse (key-on power) 40-1247
(10A) 40-1145
40-915
40-877
40-791
40-723
40-701
40-621
Ba018 Engine ECU fuse 40-596 40-1331
(key-on power) 40-1247
(7.5A) 40-1145
40-791
40-701
40-621
Ba019 RH sidelights fuse 40-915 40-1331
(7.5A)
Ba020 LH sidelights fuse 40-915 40-1331
(7.5A)
Ba021 MK1 relay fuse 30A 40-791 40-1331
40-1145
40-1024
40-976
40-877
Ba022 Protection fuse, FT 40-750 40-1331
5-6-7-8 (30A) 40-1024
40-976
40-758
40-755
Ba023 Fan/compressor 40-637 40-1331
fuse (30 A) 40-671
40-665
40-641

40-77
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba024 Starter fuse (40A) 40-596 40-1331
40-1145
40-701
40-621
Ba025 Protection fuse 40-665 40-1331
(40A) 40-1099
40-1024
40-750
40-671
Ba026 MK3 relay fuse 30A 40-637 40-1331
40-1237
40-1024
40-976
40-915
40-877
40-758
40-755
40-671
40-665
40-641
Ba027 Distributor 7-8 fuse 40-1237 40-1331
(5A)
Ba028 Power socket fuse [LNK] 40-1331
(30A)
Ba029 Not used [LNK] 40-1331
Ba030 Steering column 40-915 40-1331
stalk fuse - lights in- 40-1099
put (20A)
Ba031 Ventilation/heating 40-637 40-1331
fuse (20A) 40-671
40-665
40-641

40-78
Wiring diagrams
Table 97
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bd001 Air conditioning com- [LNK] 40-1392
pressor fuse (10A)
Bd002 Trailer brake lights 40-807 40-1392
fuse (key-on power) 40-1166
(7.5A) 40-889
Bd003 Emergency fuse (di- 40-942 40-1392
rect) (20A)
Bd004 Seat compressor / 40-1130 40-1392
cigarette lighter fuse
(direct) (15A)
Bd005 Brake lights fuse [LNK] 40-1392
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bd006 Instrument panel 40-807 40-1392
fuse (direct) (5A) 40-1255
40-889
Bd007 Hydraulic reverse 40-807 40-1392
shuttle fuse (direct) 40-1255
(7.5A) 40-1166
Bd008 Low beam head- 40-942 40-1392
lights fuse (15A)
Bd009 High beam head- [LNK] 40-1392
lights fuse (15A)
Bd010 Ancillary fuse (lift) 40-1076 40-1392
(15A)
Bd011 Turn indicator lights 40-889 40-1392
fuse (key-on power)
(15A)
Bd012 Socket fuse (key-on [LNK] 40-1392
power) (7.5A)
Bd013 Front loader fuse [LNK] 40-1392
(key-on power)
(7.5A)
Bd014 Fuse for work lights 40-1076 40-1392
on cab (key-on pow-
er) (15A)
Bd015 Fuse for low work 40-1076 40-1392
lights (key-on power)
(15A)
Bd016 Relay fuse (key-on 40-807 40-1392
power) (3A) 40-1166
40-1076
40-942
40-889
Bd017 Instrument panel 40-714 40-1392
fuse (key-on power) 40-1255
(10A) 40-1166
40-942
40-889
40-807
40-738

40-79
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bd018 Engine ECU fuse 40-714 40-1392
(key-on power) 40-1255
(7.5A) 40-1166
40-807
Bd019 RH sidelights fuse 40-942 40-1392
(7.5A)
Bd020 LH sidelights fuse 40-942 40-1392
(7.5A)
Bd021 MK1 relay fuse 30A 40-807 40-1392
40-1166
40-1076
40-889
Bd022 Protection fuse, FT 40-1166 40-1392
5-6-7-8 (30A)
Bd023 Fan/compressor [LNK] 40-1392
fuse (30 A)
Bd024 Starter fuse (40A) 40-714 40-1392
Bd025 Protection fuse [LNK] 40-1392
(40A)
Bd026 MK3 relay fuse 30A 40-889 40-1392
40-942
Bd027 Distributor 7-8 fuse [LNK] 40-1392
(5A)
Bd028 Power socket fuse [LNK] 40-1392
(30A)
Bd029 Not used [LNK] 40-1392
Bd030 Steering column 40-942 40-1392
stalk fuse - lights in- 40-1130
put (20A)
Bd031 Ventilation/heating [LNK] 40-1392
fuse (20A)

40-80
Wiring diagrams
Table 98
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1024 40-1301
(10A - Rotating bea-
con)
Be002 Fuse 2 in fuse box F 40-1099 40-1301
(5A - Radio)
Be003 Fuse 3 in fuse box F 40-671 40-1301
(30A - Climate con-
trol)
Be005 Fuse 5 in fuse box F 40-750 40-1301
(7.5A - Windscreen
wiper)
Be006 Fuse 6 in fuse box F 40-750 40-1301
(7.5A - Rear screen
wiper)
Be007 Fuse 7 in fuse box 40-1024 40-1301
F (10A - Front work
lights)
Be008 Fuse 8 in fuse box 40-1024 40-1301
F (10A - Rear work
lights)
Bf001 Fuse 1 in fuse box F 40-976 40-1318
(10A - Rotating bea-
con)
Bf002 Fuse 2 in fuse box F [LNK] 40-1318
(5A - Radio)
Bf003 Fuse 3 in fuse box F [LNK] 40-1318
(30A - Climate con-
trol)
Bf004 Not used [LNK] 40-1318
Bf005 Fuse 5 in fuse box F 40-758 40-1318
(7.5A - Windscreen
wiper)
Bf006 Fuse 6 in fuse box F 40-758 40-1318
(7.5A - Rear screen
wiper)
Bf007 Fuse 7 in fuse box 40-976 40-1318
F (10A - Front work
lights)
Bf008 Fuse 8 in fuse box 40-976 40-1318
F (10A - Rear work
lights)
Bg001 10A fuse (beacon) 40-976 40-1388
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-665 40-1388
and climate control)
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)
Bg007 10A fuse (rear work 40-976 40-1388
light)
Bg008 10A fuse (front work 40-976 40-1388
lights)

40-81
 Wiring diagrams
USA version

Bb026 Bb029

Bb022

Bb023
Bb021
Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1078 - Fuse box, cab version

l Bb001 - Air conditioning compressor fuse (10A)
l Bb002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bb003 - Emergency fuse (direct) (20A)
l Bb004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bb005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bb006 - Instrument panel fuse (direct) (5A)
l Bb007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bb008 - Cluster fuse +30 (3A)
l Bb009 - Wolp fuse +30 (10A)
l Bb010 - Ancillary fuse (lift) (15A)
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb012 - Socket fuse (key-on power) (7.5A)
l Bb013 - Front loader fuse (key-on power) (7.5A)
l Bb014 - Fuse for work lights on cab (key-on power) (15A)
l Bb015 - Fuse for low work lights (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb017 - Instrument panel fuse (key-on power) (10A)
l Bb018 - Engine ECU fuse (key-on power) (7.5A)
l Bb019 - RH sidelights fuse (7.5A)
l Bb020 - LH sidelights fuse (7.5A)
l Bb021 - MK1 relay fuse 30A
l Bb022- Protection fuse, FT 5-6-7-8 (30A)
l Bb023 - Fan/compressor fuse (30A)

40-82
Wiring diagrams

Bb026 Bb029

Bb022

Bb023
Bb021
Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1078 - Fuse box, cab version

l Bb024 - Starter fuse (40A)
l Bb025 - Protection fuse (40A)
l Bb026 - MK3 relay fuse 30A
l Bb027 - Distributor 7-8 fuse (5A)
l Bb028 - Power socket fuse (30A)
l Bb029 - Not used
l Bb030 - Steering column stalk fuse - lights input (20A)
l Bb031 - Ventilation/heating fuse (20A)

40-83
 Wiring diagrams

Bh026 Bh029

Bh022

Bh023
Bh021
Bh027 Bh030

Bh028 Bh031
Bh020

Bh019

Bh018

Bh017

Bh016

Bh015

Bh014

Bh013

Bh012

Bh011
Bh001

Bh002

Bh003

Bh004

Bh005

Bh006

Bh007

Bh008

Bh009

Bh010

Fig. 1079 - Fuse box, platform version

l Bh001 - Air conditioning compressor fuse (10A)
l Bh002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bh003 - Emergency fuse (direct) (20A)
l Bh004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bh005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bh006 - Instrument panel fuse (direct) (5A)
l Bh007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bh008 - Cluster fuse +30 (3A)
l Bh009 - Wolp fuse +30 (10A)
l Bh010 - Ancillary fuse (lift) (15A)
l Bh011 - Turn indicator lights fuse (key-on power) (15A)
l Bh012 - Socket fuse (key-on power) (7.5A)
l Bh013 - Front loader fuse (key-on power) (7.5A)
l Bh014 - Fuse for work lights on cab (key-on power) (15A)
l Bh015 - Fuse for low work lights (key-on power) (15A)
l Bh016 - Relay fuse (key-on power) (3A)
l Bh017 - Instrument panel fuse (key-on power) (10A)
l Bh018 - Engine ECU fuse (key-on power) (7.5A)
l Bh019 - RH sidelights fuse (7.5A)
l Bh020 - LH sidelights fuse (7.5A)
l Bh021 - MK1 relay fuse 30A
l Bh022 - Protection fuse, FT 5-6-7-8 (30A)
l Bh023 - Fan/compressor fuse (30A)
l Bh024 - Starter fuse (40A)
l Bh025 - Protection fuse (40A)

40-84
Wiring diagrams

Bh026 Bh029

Bh022

Bh023
Bh021
Bh027 Bh030

Bh028 Bh031
Bh020

Bh019

Bh018

Bh017

Bh016

Bh015

Bh014

Bh013

Bh012

Bh011
Bh001

Bh002

Bh003

Bh004

Bh005

Bh006

Bh007

Bh008

Bh009

Bh010

Fig. 1079 - Fuse box, platform version

l Bh026 - MK3 relay fuse 30A
l Bh027 - Distributor 7-8 fuse (5A)
l Bh028 - Power socket fuse (30A)
l Bh029 - Not used
l Bh030 - Steering column stalk fuse - lights input (20A)
l Bh031 - Ventilation/heating fuse (20A)

40-85
 Wiring diagrams
Table 99
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-604 40-1295
40-1240
40-1206
40-1186
40-1087
40-1042
40-992
40-953
40-928
40-895
40-882
40-764
40-769
40-772
40-743
40-728
40-719
40-705
40-683
40-677
40-652
40-647
40-629
40-1255
40-1247
40-641
B002 Preheat fuse 125A 40-604 40-1290
40-719
40-705
40-629
B003 0.900.0783.1 60A fuse 40-647 40-1295
40-1110
40-1042
40-992
40-764
40-769
40-772
40-683
40-677
40-652
40-641

40-86
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B004 0.900.0783.1 60A fuse 40-647 40-1295
40-1240
40-1206
40-1186
40-1137
40-1110
40-1087
40-1042
40-992
40-953
40-928
40-895
40-882
40-843
40-826
40-764
40-769
40-772
40-683
40-677
40-652
40-641
Table 100
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb001 Air conditioning com- 40-683 40-1347
pressor fuse (10A) 40-677
Bb002 Trailer brake lights 40-882 40-1347
fuse (key-on power) 40-1186
(7.5A)
Bb003 Emergency fuse (di- 40-928 40-1347
rect) (20A)
Bb004 Seat compressor / 40-1110 40-1347
cigarette lighter fuse
(direct) (15A)
Bb005 Brake lights fuse 40-928 40-1347
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bb006 Instrument panel 40-1247 40-1347
fuse (direct) (5A) 40-826
Bb007 Hydraulic reverse 40-1247 40-1347
shuttle fuse (direct) 40-1186
(7.5A)
Bb008 Low beam head- 40-928 40-1347
lights fuse (15A)
Bb009 High beam head- 40-928 40-1347
lights fuse (15A)
Bb010 Ancillary fuse (lift) [LNK] 40-1347
(15A)

40-87
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb011 Turn indicator lights 40-647 40-1347
fuse (key-on power) 40-1042
(15A) 40-992
40-928
40-882
40-764
40-769
40-772
40-683
40-677
40-652
Bb012 Socket fuse (key-on 40-928 40-1347
power) (7.5A)
Bb013 Front loader fuse [LNK] 40-1347
(key-on power)
(7.5A)
Bb014 Fuse for work lights 40-992 40-1347
on cab (key-on pow- 40-1042
er) (15A)
Bb015 Fuse for low work 40-992 40-1347
lights (key-on power) 40-1042
(15A)
Bb016 Relay fuse (key-on 40-647 40-1347
power) (3A) 40-1240
40-1186
40-1042
40-992
40-928
40-882
40-826
40-764
40-769
40-772
40-683
40-677
40-652
Bb017 Instrument panel 40-1247 40-1347
fuse (key-on power) 40-1186
(10A) 40-928
40-882
40-826
40-728
40-705
40-604
Bb018 Engine ECU fuse 40-1247 40-1347
(key-on power) 40-1186
(7.5A) 40-705
40-604
Bb019 RH sidelights fuse 40-928 40-1347
(7.5A)
Bb020 LH sidelights fuse 40-928 40-1347
(7.5A)
Bb021 MK1 relay fuse 30A 40-826 40-1347
40-1186
40-1042
40-992
40-882

40-88
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb022 Protection fuse, FT 40-764 40-1347
5-6-7-8 (30A) 40-1042
40-992
40-826
40-769
40-772
Bb023 Fan/compressor 40-647 40-1347
fuse (30 A) 40-683
40-677
40-652
Bb024 Starter fuse (40A) 40-604 40-1347
40-1186
40-705
Bb025 Protection fuse 40-683 40-1347
(40A) 40-1110
40-1042
40-992
40-677
Bb026 MK3 relay fuse 30A 40-647 40-1347
40-1240
40-1042
40-992
40-928
40-882
40-764
40-769
40-772
40-683
40-677
40-652
Bb027 Distributor 7-8 fuse 40-1240 40-1347
(5A)
Bb028 Power socket fuse [LNK] 40-1347
(30A)
Bb029 Not used [LNK] 40-1347
Bb030 Steering column 40-928 40-1347
stalk fuse - lights in- 40-1110
put (20A)
Bb031 Ventilation/heating 40-647 40-1347
fuse (20A) 40-683
40-677
40-652

40-89
 Wiring diagrams
Table 101
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1042 40-1301
(10A - Rotating bea-
con)
Be002 Fuse 2 in fuse box F 40-1110 40-1301
(5A - Radio)
Be003 Fuse 3 in fuse box F 40-677 40-1301
(30A - Climate con-
trol)
Be005 Fuse 5 in fuse box F 40-764 40-1301
(7.5A - Windscreen
wiper)
Be006 Fuse 6 in fuse box F 40-764 40-1301
(7.5A - Rear screen
wiper)
Be007 Fuse 7 in fuse box 40-1042 40-1301
F (10A - Front work
lights)
Be008 Fuse 8 in fuse box 40-1042 40-1301
F (10A - Rear work
lights)
Bf001 Fuse 1 in fuse box F 40-992 40-1318
(10A - Rotating bea-
con)
Bf002 Fuse 2 in fuse box F [LNK] 40-1318
(5A - Radio)
Bf003 Fuse 3 in fuse box F [LNK] 40-1318
(30A - Climate con-
trol)
Bf004 Not used [LNK] 40-1318
Bf005 Fuse 5 in fuse box F 40-772 40-1318
(7.5A - Windscreen
wiper)
Bf006 Fuse 6 in fuse box F 40-772 40-1318
(7.5A - Rear screen
wiper)
Bf007 Fuse 7 in fuse box 40-992 40-1318
F (10A - Front work
lights)
Bf008 Fuse 8 in fuse box 40-992 40-1318
F (10A - Rear work
lights)
Bg001 10A fuse (beacon) 40-992 40-1388
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-683 40-1388
and climate control)
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)
Bg007 10A fuse (rear work 40-992 40-1388
light)
Bg008 10A fuse (front work 40-992 40-1388
lights)

40-90
Wiring diagrams
Table 102
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bh001 Air conditioning com- [LNK] 40-1410
pressor fuse (10A)
Bh002 Trailer brake lights 40-843 40-1410
fuse (key-on power) 40-1206
(7.5A) 40-895
Bh003 Emergency fuse (di- 40-843 40-1410
rect) (20A) 40-953
Bh004 Seat compressor / 40-1137 40-1410
cigarette lighter fuse
(direct) (15A)
Bh005 Brake lights fuse 40-953 40-1410
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bh006 Instrument panel 40-1255 40-1410
fuse (direct) (5A) 40-843
Bh007 Hydraulic reverse 40-1255 40-1410
shuttle fuse (direct) 40-1206
(7.5A) 40-843
Bh008 Low beam head- 40-953 40-1410
lights fuse (15A)
Bh009 High beam head- 40-953 40-1410
lights fuse (15A)
Bh010 Ancillary fuse (lift) 40-1087 40-1410
(15A)
Bh011 Turn indicator lights 40-895 40-1410
fuse (key-on power) 40-953
(15A)
Bh012 Socket fuse (key-on 40-953 40-1410
power) (7.5A)
Bh013 Front loader fuse [LNK] 40-1410
(key-on power)
(7.5A)
Bh014 Fuse for work lights 40-1087 40-1410
on cab (key-on pow-
er) (15A)
Bh015 Fuse for low work 40-1087 40-1410
lights (key-on power)
(15A)
Bh016 Relay fuse (key-on 40-843 40-1410
power) (3A) 40-1206
40-1087
40-953
40-895
Bh017 Instrument panel 40-1255 40-1410
fuse (key-on power) 40-1206
(10A) 40-953
40-895
40-843
40-743
40-719
40-629

40-91
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bh018 Engine ECU fuse 40-1255 40-1410
(key-on power) 40-1206
(7.5A) 40-843
40-719
40-629
Bh019 RH sidelights fuse 40-953 40-1410
(7.5A)
Bh020 LH sidelights fuse 40-953 40-1410
(7.5A)
Bh021 MK1 relay fuse 30A 40-843 40-1410
40-1206
40-1087
40-895
Bh022 Protection fuse, FT 40-1206 40-1410
5-6-7-8 (30A)
Bh023 Fan/compressor [LNK] 40-1410
fuse (30 A)
Bh024 Starter fuse (40A) 40-629 40-1410
40-719
Bh025 Protection fuse [LNK] 40-1410
(40A)
Bh026 MK3 relay fuse 30A 40-895 40-1410
40-953
Bh027 Distributor 7-8 fuse [LNK] 40-1410
(5A)
Bh028 Power socket fuse [LNK] 40-1410
(30A)
Bh029 Not used [LNK] 40-1410
Bh030 Steering column 40-953 40-1410
stalk fuse - lights in- 40-1137
put (20A)
Bh031 Ventilation/heating [LNK] 40-1410
fuse (20A)

40-92
Wiring diagrams
40.2.9 - B - Fuses (AGROFARM 430 -> ZKDW430200TD25001)
ITA version

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1080 - Fuse box, cab version

l Ba001 - Air conditioning compressor fuse (10A)
l Ba002 - Trailer brake lights fuse (key-on power) (7.5A)
l Ba003 - Emergency fuse (direct) (20A)
l Ba004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Ba005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Ba006 - Instrument panel fuse (direct) (5A)
l Ba007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Ba008 +30 cluster fuse (3A)
l Ba009 +30 Wolp fuse (10A)
l Ba010 - Ancillary fuse (lift) (15A)
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba012 - Socket fuse (key-on power) (7.5A)
l Ba013 - Front loader fuse (key-on power) (7.5A)
l Ba014 - Fuse for work lights on cab (key-on power) (15A)
l Ba015 - Fuse for low work lights (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba017 - Instrument panel fuse (key-on power) (10A)
l Ba018 - Engine ECU fuse (key-on power) (7.5A)
l Ba019 - RH sidelights fuse (7.5A)
l Ba020 - LH sidelights fuse (7.5A)
l Ba021 - MK1 relay fuse 30A
l Ba022 - Protection fuse, FT 5-6-7-8 (30A)

40-93
 Wiring diagrams

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1080 - Fuse box, cab version

l Ba023 - Fan/compressor fuse (30A)
l Ba024 - Starter fuse (40A)
l Ba025 - Protection fuse (40A)
l Ba026 - MK3 relay fuse 30A
l Ba027 - Distributor 7-8 fuse (5A)
l Ba028 - Power socket fuse (key-on power) (30A)
l Ba029 - Not used
l Ba030 - Steering column stalk fuse - lights input (20A)
l Ba031 - Ventilation/heating fuse (20A)

40-94
Wiring diagrams

Bc026 Bc029

Bc022

Bc023
Bc021
Bc027 Bc030

Bc028 Bc031
Bc020

Bc019

Bc018

Bc017

Bc016

Bc015

Bc014

Bc013

Bc012

Bc011
Bc001

Bc002

Bc003

Bc004

Bc005

Bc006

Bc007

Bc008

Bc009

Bc010

Fig. 1081 - Fuse box, cab version with electronic lift

l Bc001 - Air conditioning compressor fuse (10A)
l Bc002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bc003 - Emergency fuse (direct) (20A)
l Bc004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bc005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bc006 - Instrument panel fuse (direct) (5A)
l Bc007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bc008 - Cluster fuse +30 (3A)
l Bc009 - Wolp fuse +30 (10A)
l Bc010 - Ancillary fuse (lift) (15A)
l Bc011 - Turn indicator lights fuse (key-on power) (15A)
l Bc012 - Socket fuse (key-on power) (7.5A)
l Bc013 - Front loader fuse (key-on power) (7.5A)
l Bc014 - Fuse for work lights on cab (key-on power) (15A)
l Bc015 - Fuse for low work lights (key-on power) (15A)
l Bc016 - Relay fuse (key-on power) (3A)
l Bc017 - Instrument panel fuse (key-on power) (10A)
l Bc018 - Engine ECU fuse (key-on power) (7.5A)
l Bc019 - RH sidelights fuse (7.5A)
l Bc020 - LH sidelights fuse (7.5A)
l Bc021 - MK1 relay fuse 30A
l Bc022 - Protection fuse, FT 5-6-7-8 (30A)
l Bc023 - Fan/compressor fuse (30A)
l Bc024 - Starter fuse (40A)
l Bc025 - Protection fuse (40A)

40-95
 Wiring diagrams

Bc026 Bc029

Bc022

Bc023
Bc021
Bc027 Bc030

Bc028 Bc031
Bc020

Bc019

Bc018

Bc017

Bc016

Bc015

Bc014

Bc013

Bc012

Bc011
Bc001

Bc002

Bc003

Bc004

Bc005

Bc006

Bc007

Bc008

Bc009

Bc010

Fig. 1081 - Fuse box, cab version with electronic lift

l Bc026 - MK3 relay fuse 30A
l Bc027 - Distributor 7-8 fuse (5A)
l Bc028 - Power socket fuse (30A)
l Bc029 - Not used
l Bc030 - Steering column stalk fuse - lights input (20A)
l Bc031 - Ventilation/heating fuse (20A)

40-96
Wiring diagrams

Bd026 Bd029

Bd022

Bd023
Bd021
Bd027 Bd030

Bd028 Bd031
Bd020

Bd019

Bd018

Bd017

Bd016

Bd015

Bd014

Bd013

Bd012

Bd011
Bd001

Bd002

Bd003

Bd004

Bd005

Bd006

Bd007

Bd008

Bd009

Bd010

Fig. 1082 - Fuse box, platform version

l Bd001 - Air conditioning compressor fuse (10A)
l Bd002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bd003 - Emergency fuse (direct) (20A)
l Bd004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bd005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bd006 - Instrument panel fuse (direct) (5A)
l Bd007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bd008 - Cluster fuse +30 (3A)
l Bd009 - Wolp fuse +30 (10A)
l Bd010 - Ancillary fuse (lift) (15A)
l Bd011 - Turn indicator lights fuse (key-on power) (15A)
l Bd012 - Socket fuse (key-on power) (7.5A)
l Bd013 - Front loader fuse (key-on power) (7.5A)
l Bd014 - Fuse for work lights on cab (key-on power) (15A)
l Bd015 - Fuse for low work lights (key-on power) (15A)
l Bd016 - Relay fuse (key-on power) (3A)
l Bd017 - Instrument panel fuse (key-on power) (10A)
l Bd018 - Engine ECU fuse (key-on power) (7.5A)
l Bd019 - RH sidelights fuse (7.5A)
l Bd020 - LH sidelights fuse (7.5A)
l Bd021 - MK1 relay fuse 30A
l Bd022 - Protection fuse, FT 5-6-7-8 (30A)
l Bd023 - Fan/compressor fuse (30A)
l Bd024 - Starter fuse (40A)
l Bd025 - Protection fuse (40A)

40-97
 Wiring diagrams

Bd026 Bd029

Bd022

Bd023
Bd021
Bd027 Bd030

Bd028 Bd031
Bd020

Bd019

Bd018

Bd017

Bd016

Bd015

Bd014

Bd013

Bd012

Bd011
Bd001

Bd002

Bd003

Bd004

Bd005

Bd006

Bd007

Bd008

Bd009

Bd010

Fig. 1082 - Fuse box, platform version

l Bd026 - MK3 relay fuse 30A
l Bd027 - Distributor 7-8 fuse (5A)
l Bd028 - Power socket fuse (30A)
l Bd029 - Not used
l Bd030 - Steering column stalk fuse - lights input (20A)
l Bd031 - Ventilation/heating fuse (20A)

40-98
Wiring diagrams
Table 103
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-596 40-1295
40-1255
40-1166
40-1076
40-889
40-953
40-807
40-714
40-738
40-621
40-1262
40-1243
40-1269
40-1226
40-1059
40-1008
40-964
40-902
40-862
40-778
40-783
40-787
40-734
40-710
40-657
40-660
40-689
40-695
40-613
40-1247
40-1237
40-1145
40-1024
40-976
40-915
40-877
40-791
40-758
40-755
40-750
40-723
40-701
40-671
40-665
40-641
40-637
B002 Preheat fuse 125A 40-596 40-1290
40-714
40-621
40-710
40-613
40-701

40-99
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B003 0.900.0783.1 60A fuse 40-637 40-1295
40-807
40-1120
40-1059
40-1008
40-778
40-783
40-787
40-689
40-695
40-657
40-660
40-1099
40-1024
40-976
40-758
40-755
40-750
40-671
40-665
40-641
B004 0.900.0783.1 60A fuse 40-637 40-1295
40-1166
40-1076
40-1130
40-953
40-889
40-807
40-1262
40-1243
40-1269
40-1226
40-1120
40-1059
40-1008
40-964
40-902
40-862
40-778
40-783
40-787
40-689
40-695
40-657
40-660
40-1237
40-1145
40-1099
40-1024
40-976
40-915
40-877
40-791
40-758
40-755
40-750
40-671
40-665
40-641
Ba001 Air conditioning com- 40-665 40-1331
pressor fuse (10A) 40-671

40-100
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba002 Trailer brake lights 40-791 40-1331
fuse (key-on power) 40-877
(7.5A)
Ba003 Emergency fuse (di- 40-915 40-1331
rect) (20A)
Ba004 Seat compressor / 40-1099 40-1331
cigarette lighter fuse
(direct) (15A)
Ba005 Brake lights fuse 40-877 40-1331
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Ba006 Instrument panel 40-791 40-1331
fuse (direct) (5A) 40-1247
Ba007 Hydraulic reverse 40-791 40-1331
shuttle fuse (direct) 40-1247
(7.5A) 40-1145
Ba008 Low beam head- 40-915 40-1331
lights fuse (15A)
Ba009 High beam head- 40-915 40-1331
lights fuse (15A)
Ba010 Ancillary fuse (lift) [LNK] 40-1331
(15A)
Ba011 Turn indicator lights 40-637 40-1331
fuse (key-on power) 40-1024
(15A) 40-976
40-915
40-877
40-758
40-755
40-750
40-671
40-665
40-641
Ba012 Socket fuse (key-on [LNK] 40-1331
power) (7.5A)
Ba013 Front loader fuse [LNK] 40-1331
(key-on power)
(7.5A)
Ba014 Fuse for work lights 40-976 40-1331
on cab (key-on pow- 40-1024
er) (15A)
Ba015 Fuse for low work 40-976 40-1331
lights (key-on power) 40-1024
(15A)

40-101
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba016 Relay fuse (key-on 40-637 40-1331
power) (3A) 40-1237
40-1145
40-1024
40-976
40-915
40-877
40-791
40-758
40-755
40-750
40-671
40-665
40-641
Ba017 Instrument panel 40-596 40-1331
fuse (key-on power) 40-1247
(10A) 40-1145
40-915
40-877
40-791
40-723
40-701
Ba018 Engine ECU fuse 40-596 40-1331
(key-on power) 40-1247
(7.5A) 40-1145
40-791
40-701
Ba019 RH sidelights fuse 40-915 40-1331
(7.5A)
Ba020 LH sidelights fuse 40-915 40-1331
(7.5A)
Ba021 MK1 relay fuse 30A 40-791 40-1331
40-1145
40-1024
40-976
40-877
Ba022 Protection fuse, FT 40-750 40-1331
5-6-7-8 (30A) 40-1024
40-976
40-758
40-755
Ba023 Fan/compressor 40-637 40-1331
fuse (30 A) 40-671
40-665
40-641
Ba024 Starter fuse (40A) 40-596 40-1331
40-1145
40-701
Ba025 Protection fuse 40-665 40-1331
(40A) 40-1099
40-1024
40-750
40-671

40-102
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba026 MK3 relay fuse 30A 40-637 40-1331
40-1237
40-1024
40-976
40-915
40-877
40-758
40-755
40-671
40-665
40-641
Ba027 Distributor 7-8 fuse 40-1237 40-1331
(5A)
Ba028 Power socket fuse [LNK] 40-1331
(30A)
Ba029 Not used [LNK] 40-1331
Ba030 Steering column 40-915 40-1331
stalk fuse - lights in- 40-1099
put (20A)
Ba031 Ventilation/heating 40-637 40-1331
fuse (20A) 40-671
40-665
40-641

Table 104
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc001 Air conditioning com- 40-689 40-1365
pressor fuse (10A) 40-695
Bc002 Trailer brake lights 40-862 40-1365
fuse (key-on power) 40-902
(7.5A)
Bc003 Emergency fuse (di- 40-964 40-1365
rect) (20A)
Bc004 Seat compressor / 40-1120 40-1365
cigarette lighter fuse
(direct) (15A)
Bc005 Brake lights fuse 40-902 40-1365
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bc006 Instrument panel 40-862 40-1365
fuse (direct) (5A) 40-1262
40-902
Bc007 Hydraulic reverse 40-862 40-1365
shuttle fuse (direct) 40-1262
(7.5A) 40-1226
Bc008 Low beam head- 40-964 40-1365
lights fuse (15A)
Bc009 High beam head- 40-964 40-1365
lights fuse (15A)

40-103
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc010 Ancillary fuse (lift) 40-862 40-1365
(15A) 40-1262
40-1243
40-1269
40-1226
40-1059
40-1008
Bc011 Turn indicator lights 40-657 40-1365
fuse (key-on power) 40-1059
(15A) 40-1008
40-964
40-778
40-783
40-787
40-689
40-695
40-660
Bc012 Socket fuse (key-on [LNK] 40-1365
power) (7.5A)
Bc013 Front loader fuse [LNK] 40-1365
(key-on power)
(7.5A)
Bc014 Fuse for work lights 40-1008 40-1365
on cab (key-on pow- 40-1059
er) (15A)
Bc015 Fuse for low work [LNK] 40-1365
lights (key-on power)
(15A)
Bc016 Relay fuse (key-on 40-657 40-1365
power) (3A) 40-1059
40-1008
40-964
40-902
40-862
40-778
40-783
40-787
40-689
40-695
40-660
Bc017 Instrument panel 40-613 40-1365
fuse (key-on power) 40-1262
(10A) 40-1243
40-1269
40-1226
40-964
40-902
40-862
40-734
40-710
Bc018 Engine ECU fuse 40-613 40-1365
(key-on power) 40-1262
(7.5A) 40-1226
40-862
40-710
Bc019 RH sidelights fuse 40-964 40-1365
(7.5A)
Bc020 LH sidelights fuse 40-964 40-1365
(7.5A)

40-104
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc021 MK1 relay fuse 30A 40-862 40-1365
40-1059
40-1008
40-902
Bc022 Protection fuse, FT 40-778 40-1365
5-6-7-8 (30A) 40-1059
40-1008
40-783
40-787
Bc023 Fan/compressor 40-657 40-1365
fuse (30 A) 40-689
40-695
40-660
Bc024 Starter fuse (40A) 40-613 40-1365
40-1226
40-710
Bc025 Protection fuse 40-689 40-1365
(40A) 40-1120
40-1059
40-1008
40-695
Bc026 MK3 relay fuse 30A 40-657 40-1365
40-1059
40-1008
40-964
40-778
40-783
40-787
40-689
40-695
40-660
Bc027 Distributor 7-8 fuse [LNK] 40-1365
(5A)
Bc028 Power socket fuse [LNK] 40-1365
(30A)
Bc029 Not used [LNK] 40-1365
Bc030 Steering column 40-964 40-1365
stalk fuse - lights in- 40-1120
put (20A)
Bc031 Ventilation/heating 40-657 40-1365
fuse (20A) 40-689
40-695
40-660

40-105
 Wiring diagrams
Table 105
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bd001 Air conditioning com- [LNK] 40-1392
pressor fuse (10A)
Bd002 Trailer brake lights 40-889 40-1392
fuse (key-on power) 40-1166
(7.5A) 40-807
Bd003 Emergency fuse (di- 40-953 40-1392
rect) (20A)
Bd004 Seat compressor / 40-1130 40-1392
cigarette lighter fuse
(direct) (15A)
Bd005 Brake lights fuse [LNK] 40-1392
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bd006 Instrument panel 40-889 40-1392
fuse (direct) (5A) 40-1255
40-807
Bd007 Hydraulic reverse 40-807 40-1392
shuttle fuse (direct) 40-1255
(7.5A) 40-1166
Bd008 Low beam head- 40-953 40-1392
lights fuse (15A)
Bd009 High beam head- 40-953 40-1392
lights fuse (15A)
Bd010 Ancillary fuse (lift) 40-1076 40-1392
(15A)
Bd011 Turn indicator lights 40-889 40-1392
fuse (key-on power) 40-953
(15A)
Bd012 Socket fuse (key-on [LNK] 40-1392
power) (7.5A)
Bd013 Front loader fuse [LNK] 40-1392
(key-on power)
(7.5A)
Bd014 Fuse for work lights 40-1076 40-1392
on cab (key-on pow-
er) (15A)
Bd015 Fuse for low work 40-1076 40-1392
lights (key-on power)
(15A)
Bd016 Relay fuse (key-on 40-889 40-1392
power) (3A) 40-1166
40-1076
40-953
40-807
Bd017 Instrument panel 40-889 40-1392
fuse (key-on power) 40-1255
(10A) 40-738
40-1166
40-953
40-714
40-807
40-621

40-106
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bd018 Engine ECU fuse 40-621 40-1392
(key-on power) 40-1255
(7.5A) 40-807
40-1166
40-714
Bd019 RH sidelights fuse 40-953 40-1392
(7.5A)
Bd020 LH sidelights fuse 40-953 40-1392
(7.5A)
Bd021 MK1 relay fuse 30A 40-889 40-1392
40-1166
40-1076
40-807
Bd022 Protection fuse, FT 40-1166 40-1392
5-6-7-8 (30A)
Bd023 Fan/compressor [LNK] 40-1392
fuse (30 A)
Bd024 Starter fuse (40A) 40-621 40-1392
40-714
Bd025 Protection fuse [LNK] 40-1392
(40A)
Bd026 MK3 relay fuse 30A 40-889 40-1392
40-953
Bd027 Distributor 7-8 fuse [LNK] 40-1392
(5A)
Bd028 Power socket fuse [LNK] 40-1392
(30A)
Bd029 Not used [LNK] 40-1392
Bd030 Steering column 40-953 40-1392
stalk fuse - lights in- 40-1130
put (20A)
Bd031 Ventilation/heating [LNK] 40-1392
fuse (20A)

40-107
 Wiring diagrams
Table 106
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1024 40-1301
(10A - Rotating bea- 40-1059
con)
Be002 Fuse 2 in fuse box F 40-1099 40-1301
(5A - Radio) 40-1120
Be003 Fuse 3 in fuse box F 40-671 40-1301
(30A - Climate con- 40-695
trol)
Be005 Fuse 5 in fuse box F 40-750 40-1301
(7.5A - Windscreen 40-778
wiper)
Be006 Fuse 6 in fuse box F 40-750 40-1301
(7.5A - Rear screen 40-778
wiper)
Be007 Fuse 7 in fuse box 40-1024 40-1301
F (10A - Front work 40-1059
lights)
Be008 Fuse 8 in fuse box 40-1024 40-1301
F (10A - Rear work 40-1059
lights)
Bf001 Fuse 1 in fuse box F 40-976 40-1318
(10A - Rotating bea-
con)
Bf002 Fuse 2 in fuse box F [LNK] 40-1318
(5A - Radio)
Bf003 Fuse 3 in fuse box F [LNK] 40-1318
(30A - Climate con-
trol)
Bf004 Not used [LNK] 40-1318
Bf005 Fuse 5 in fuse box F 40-758 40-1318
(7.5A - Windscreen
wiper)
Bf006 Fuse 6 in fuse box F 40-758 40-1318
(7.5A - Rear screen
wiper)
Bf007 Fuse 7 in fuse box 40-976 40-1318
F (10A - Front work
lights)
Bf008 Fuse 8 in fuse box 40-976 40-1318
F (10A - Rear work
lights)
Bg001 10A fuse (beacon) 40-976 40-1388
40-1008
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-665 40-1388
and climate control) 40-689
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)
Bg007 10A fuse (rear work 40-976 40-1388
light) 40-1008
Bg008 10A fuse (front work 40-976 40-1388
lights) 40-1008

40-108
Wiring diagrams
USA version

Bb026 Bb029

Bb022

Bb023
Bb021
Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1083 - Fuse box, cab version

l Bb001 - Air conditioning compressor fuse (10A)
l Bb002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bb003 - Emergency fuse (direct) (20A)
l Bb004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bb005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bb006 - Instrument panel fuse (direct) (5A)
l Bb007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bb008 - Cluster fuse +30 (3A)
l Bb009 - Wolp fuse +30 (10A)
l Bb010 - Ancillary fuse (lift) (15A)
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb012 - Socket fuse (key-on power) (7.5A)
l Bb013 - Front loader fuse (key-on power) (7.5A)
l Bb014 - Fuse for work lights on cab (key-on power) (15A)
l Bb015 - Fuse for low work lights (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb017 - Instrument panel fuse (key-on power) (10A)
l Bb018 - Engine ECU fuse (key-on power) (7.5A)
l Bb019 - RH sidelights fuse (7.5A)
l Bb020 - LH sidelights fuse (7.5A)
l Bb021 - MK1 relay fuse 30A
l Bb022- Protection fuse, FT 5-6-7-8 (30A)
l Bb023 - Fan/compressor fuse (30A)

40-109
 Wiring diagrams

Bb026 Bb029

Bb022

Bb023
Bb021
Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1083 - Fuse box, cab version

l Bb024 - Starter fuse (40A)
l Bb025 - Protection fuse (40A)
l Bb026 - MK3 relay fuse 30A
l Bb027 - Distributor 7-8 fuse (5A)
l Bb028 - Power socket fuse (30A)
l Bb029 - Not used
l Bb030 - Steering column stalk fuse - lights input (20A)
l Bb031 - Ventilation/heating fuse (20A)

40-110
Wiring diagrams

Bc026 Bc029

Bc022

Bc023
Bc021
Bc027 Bc030

Bc028 Bc031
Bc020

Bc019

Bc018

Bc017

Bc016

Bc015

Bc014

Bc013

Bc012

Bc011
Bc001

Bc002

Bc003

Bc004

Bc005

Bc006

Bc007

Bc008

Bc009

Bc010

Fig. 1083 - Fuse box, cab version with electronic lift

l Bc001 - Air conditioning compressor fuse (10A)
l Bc002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bc003 - Emergency fuse (direct) (20A)
l Bc004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bc005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bc006 - Instrument panel fuse (direct) (5A)
l Bc007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bc008 - Cluster fuse +30 (3A)
l Bc009 - Wolp fuse +30 (10A)
l Bc010 - Ancillary fuse (lift) (15A)
l Bc011 - Turn indicator lights fuse (key-on power) (15A)
l Bc012 - Socket fuse (key-on power) (7.5A)
l Bc013 - Front loader fuse (key-on power) (7.5A)
l Bc014 - Fuse for work lights on cab (key-on power) (15A)
l Bc015 - Fuse for low work lights (key-on power) (15A)
l Bc016 - Relay fuse (key-on power) (3A)
l Bc017 - Instrument panel fuse (key-on power) (10A)
l Bc018 - Engine ECU fuse (key-on power) (7.5A)
l Bc019 - RH sidelights fuse (7.5A)
l Bc020 - LH sidelights fuse (7.5A)
l Bc021 - MK1 relay fuse 30A
l Bc022 - Protection fuse, FT 5-6-7-8 (30A)
l Bc023 - Fan/compressor fuse (30A)
l Bc024 - Starter fuse (40A)
l Bc025 - Protection fuse (40A)

40-111
 Wiring diagrams

Bc026 Bc029

Bc022

Bc023
Bc021
Bc027 Bc030

Bc028 Bc031
Bc020

Bc019

Bc018

Bc017

Bc016

Bc015

Bc014

Bc013

Bc012

Bc011
Bc001

Bc002

Bc003

Bc004

Bc005

Bc006

Bc007

Bc008

Bc009

Bc010

Fig. 1083 - Fuse box, cab version with electronic lift

l Bc026 - MK3 relay fuse 30A
l Bc027 - Distributor 7-8 fuse (5A)
l Bc028 - Power socket fuse (30A)
l Bc029 - Not used
l Bc030 - Steering column stalk fuse - lights input (20A)
l Bc031 - Ventilation/heating fuse (20A)

40-112
Wiring diagrams

Bh026 Bh029

Bh022

Bh023
Bh021
Bh027 Bh030

Bh028 Bh031
Bh020

Bh019

Bh018

Bh017

Bh016

Bh015

Bh014

Bh013

Bh012

Bh011
Bh001

Bh002

Bh003

Bh004

Bh005

Bh006

Bh007

Bh008

Bh009

Bh010

Fig. 1084 - Fuse box, platform version

l Bh001 - Air conditioning compressor fuse (10A)
l Bh002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bh003 - Emergency fuse (direct) (20A)
l Bh004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bh005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bh006 - Instrument panel fuse (direct) (5A)
l Bh007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bh008 - Cluster fuse +30 (3A)
l Bh009 - Wolp fuse +30 (10A)
l Bh010 - Ancillary fuse (lift) (15A)
l Bh011 - Turn indicator lights fuse (key-on power) (15A)
l Bh012 - Socket fuse (key-on power) (7.5A)
l Bh013 - Front loader fuse (key-on power) (7.5A)
l Bh014 - Fuse for work lights on cab (key-on power) (15A)
l Bh015 - Fuse for low work lights (key-on power) (15A)
l Bh016 - Relay fuse (key-on power) (3A)
l Bh017 - Instrument panel fuse (key-on power) (10A)
l Bh018 - Engine ECU fuse (key-on power) (7.5A)
l Bh019 - RH sidelights fuse (7.5A)
l Bh020 - LH sidelights fuse (7.5A)
l Bh021 - MK1 relay fuse 30A
l Bh022 - Protection fuse, FT 5-6-7-8 (30A)
l Bh023 - Fan/compressor fuse (30A)
l Bh024 - Starter fuse (40A)
l Bh025 - Protection fuse (40A)

40-113
 Wiring diagrams

Bh026 Bh029

Bh022

Bh023
Bh021
Bh027 Bh030

Bh028 Bh031
Bh020

Bh019

Bh018

Bh017

Bh016

Bh015

Bh014

Bh013

Bh012

Bh011
Bh001

Bh002

Bh003

Bh004

Bh005

Bh006

Bh007

Bh008

Bh009

Bh010

Fig. 1084 - Fuse box, platform version

l Bh026 - MK3 relay fuse 30A
l Bh027 - Distributor 7-8 fuse (5A)
l Bh028 - Power socket fuse (30A)
l Bh029 - Not used
l Bh030 - Steering column stalk fuse - lights input (20A)
l Bh031 - Ventilation/heating fuse (20A)

40-114
Wiring diagrams
Table 107
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-604 40-1295
40-1255
40-1087
40-1206
40-719
40-964
40-826
40-743
40-629
40-1186
40-1262
40-1243
40-1269
40-1226
40-1059
40-1008
40-964
40-902
40-862
40-778
40-783
40-787
40-734
40-710
40-689
40-695
40-657
40-660
40-613
40-1240
40-1042
40-992
40-928
40-895
40-882
40-764
40-769
40-772
40-728
40-705
40-683
40-677
40-652
40-647
40-1247
40-641
B002 Preheat fuse 125A 40-604 40-1290
40-629
40-719
40-710
40-613
40-705

40-115
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B003 0.900.0783.1 60A fuse 40-647 40-1295
40-1059
40-1008
40-778
40-783
40-787
40-689
40-695
40-657
40-660
40-1110
40-1042
40-992
40-764
40-769
40-772
40-683
40-677
40-652
40-641
B004 0.900.0783.1 60A fuse 40-647 40-1295
40-1206
40-1087
40-1137
40-964
40-1262
40-826
40-1243
40-1269
40-1226
40-1186
40-1059
40-1008
40-964
40-902
40-862
40-778
40-783
40-787
40-689
40-695
40-657
40-660
40-1240
40-1110
40-1042
40-992
40-928
40-895
40-882
40-826
40-764
40-769
40-772
40-683
40-677
40-652
40-641

40-116
Wiring diagrams
Table 108
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb001 Air conditioning com- 40-683 40-1347
pressor fuse (10A) 40-677
Bb002 Trailer brake lights 40-882 40-1347
fuse (key-on power) 40-1186
(7.5A)
Bb003 Emergency fuse (di- 40-928 40-1347
rect) (20A)
Bb004 Seat compressor / 40-1110 40-1347
cigarette lighter fuse
(direct) (15A)
Bb005 Brake lights fuse 40-928 40-1347
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bb006 Instrument panel 40-1247 40-1347
fuse (direct) (5A) 40-826
40-826
Bb007 Hydraulic reverse 40-1247 40-1347
shuttle fuse (direct) 40-1186
(7.5A)
Bb008 Low beam head- 40-928 40-1347
lights fuse (15A)
Bb009 High beam head- 40-928 40-1347
lights fuse (15A)
Bb010 Ancillary fuse (lift) [LNK] 40-1347
(15A)
Bb011 Turn indicator lights 40-647 40-1347
fuse (key-on power) 40-1042
(15A) 40-992
40-928
40-882
40-764
40-769
40-772
40-683
40-677
40-652
Bb012 Socket fuse (key-on 40-928 40-1347
power) (7.5A)
Bb013 Front loader fuse [LNK] 40-1347
(key-on power)
(7.5A)
Bb014 Fuse for work lights 40-992 40-1347
on cab (key-on pow- 40-1042
er) (15A)
Bb015 Fuse for low work 40-992 40-1347
lights (key-on power) 40-1042
(15A)

40-117
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb016 Relay fuse (key-on 40-647 40-1347
power) (3A) 40-826
40-1186
40-1240
40-1042
40-992
40-928
40-882
40-826
40-764
40-769
40-772
40-683
40-677
40-652
Bb017 Instrument panel 40-1247 40-1347
fuse (key-on power) 40-1186
(10A) 40-928
40-826
40-882
40-826
40-728
40-705
40-604
Bb018 Engine ECU fuse 40-1247 40-1347
(key-on power) 40-1186
(7.5A) 40-705
40-604
Bb019 RH sidelights fuse 40-928 40-1347
(7.5A)
Bb020 LH sidelights fuse 40-928 40-1347
(7.5A)
Bb021 MK1 relay fuse 30A 40-826 40-1347
40-826
40-1186
40-1042
40-992
40-882
Bb022 Protection fuse, FT 40-764 40-1347
5-6-7-8 (30A) 40-826
40-1042
40-992
40-826
40-769
40-772
Bb023 Fan/compressor 40-647 40-1347
fuse (30 A) 40-683
40-677
40-652
Bb024 Starter fuse (40A) 40-604 40-1347
40-1186
40-705
Bb025 Protection fuse 40-683 40-1347
(40A) 40-1110
40-1042
40-992
40-677

40-118
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb026 MK3 relay fuse 30A 40-647 40-1347
40-1240
40-1042
40-992
40-928
40-882
40-764
40-769
40-772
40-683
40-677
40-652
Bb027 Distributor 7-8 fuse 40-1240 40-1347
(5A)
Bb028 Power socket fuse [LNK] 40-1347
(30A)
Bb029 Not used [LNK] 40-1347
Bb030 Steering column 40-928 40-1347
stalk fuse - lights in- 40-1110
put (20A)
Bb031 Ventilation/heating 40-647 40-1347
fuse (20A) 40-683
40-677
40-652
Table 109
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc001 Air conditioning com- 40-689 40-1365
pressor fuse (10A) 40-695
Bc002 Trailer brake lights 40-862 40-1365
fuse (key-on power) 40-902
(7.5A)
Bc003 Emergency fuse (di- 40-964 40-1365
rect) (20A)
Bc004 Seat compressor / [LNK] 40-1365
cigarette lighter fuse
(direct) (15A)
Bc005 Brake lights fuse 40-902 40-1365
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bc006 Instrument panel 40-862 40-1365
fuse (direct) (5A) 40-1262
40-902
Bc007 Hydraulic reverse 40-862 40-1365
shuttle fuse (direct) 40-1262
(7.5A) 40-1226
Bc008 Low beam head- 40-964 40-1365
lights fuse (15A)
Bc009 High beam head- 40-964 40-1365
lights fuse (15A)

40-119
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc010 Ancillary fuse (lift) 40-862 40-1365
(15A) 40-1262
40-1243
40-1269
40-1226
40-1059
40-1008
Bc011 Turn indicator lights 40-657 40-1365
fuse (key-on power) 40-1059
(15A) 40-1008
40-964
40-778
40-783
40-787
40-689
40-695
40-660
Bc012 Socket fuse (key-on [LNK] 40-1365
power) (7.5A)
Bc013 Front loader fuse [LNK] 40-1365
(key-on power)
(7.5A)
Bc014 Fuse for work lights 40-1008 40-1365
on cab (key-on pow- 40-1059
er) (15A)
Bc015 Fuse for low work [LNK] 40-1365
lights (key-on power)
(15A)
Bc016 Relay fuse (key-on 40-657 40-1365
power) (3A) 40-1059
40-1008
40-964
40-902
40-862
40-778
40-783
40-787
40-689
40-695
40-660
Bc017 Instrument panel 40-613 40-1365
fuse (key-on power) 40-1262
(10A) 40-1243
40-1269
40-1226
40-964
40-902
40-862
40-734
40-710
Bc018 Engine ECU fuse 40-613 40-1365
(key-on power) 40-1262
(7.5A) 40-1226
40-862
40-710
Bc019 RH sidelights fuse [LNK] 40-1365
(7.5A)
Bc020 LH sidelights fuse 40-964 40-1365
(7.5A)

40-120
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc021 MK1 relay fuse 30A 40-862 40-1365
40-1059
40-1008
40-902
Bc022 Protection fuse, FT 40-778 40-1365
5-6-7-8 (30A) 40-1059
40-1008
40-783
40-787
Bc023 Fan/compressor 40-657 40-1365
fuse (30 A) 40-689
40-695
40-660
Bc024 Starter fuse (40A) 40-613 40-1365
40-1226
40-710
Bc025 Protection fuse 40-689 40-1365
(40A) 40-1059
40-1008
40-695
Bc026 MK3 relay fuse 30A 40-657 40-1365
40-1059
40-1008
40-964
40-778
40-783
40-787
40-689
40-695
40-660
Bc027 Distributor 7-8 fuse [LNK] 40-1365
(5A)
Bc028 Power socket fuse [LNK] 40-1365
(30A)
Bc029 Not used [LNK] 40-1365
Bc030 Steering column 40-964 40-1365
stalk fuse - lights in-
put (20A)
Bc031 Ventilation/heating 40-657 40-1365
fuse (20A) 40-689
40-695
40-660

40-121
 Wiring diagrams
Table 110
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1042 40-1301
(10A - Rotating bea- 40-1059
con)
Be002 Fuse 2 in fuse box F 40-1110 40-1301
(5A - Radio)
Be003 Fuse 3 in fuse box F 40-677 40-1301
(30A - Climate con- 40-695
trol)
Be005 Fuse 5 in fuse box F 40-764 40-1301
(7.5A - Windscreen 40-778
wiper)
Be006 Fuse 6 in fuse box F 40-764 40-1301
(7.5A - Rear screen 40-778
wiper)
Be007 Fuse 7 in fuse box 40-1042 40-1301
F (10A - Front work 40-1059
lights)
Be008 Fuse 8 in fuse box 40-1042 40-1301
F (10A - Rear work 40-1059
lights)
Bf001 Fuse 1 in fuse box F 40-992 40-1318
(10A - Rotating bea-
con)
Bf002 Fuse 2 in fuse box F [LNK] 40-1318
(5A - Radio)
Bf003 Fuse 3 in fuse box F [LNK] 40-1318
(30A - Climate con-
trol)
Bf004 Not used [LNK] 40-1318
Bf005 Fuse 5 in fuse box F 40-772 40-1318
(7.5A - Windscreen
wiper)
Bf006 Fuse 6 in fuse box F 40-772 40-1318
(7.5A - Rear screen
wiper)
Bf007 Fuse 7 in fuse box 40-992 40-1318
F (10A - Front work
lights)
Bf008 Fuse 8 in fuse box 40-992 40-1318
F (10A - Rear work
lights)
Bg001 10A fuse (beacon) 40-992 40-1388
40-1008
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-683 40-1388
and climate control) 40-689
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)
Bg007 10A fuse (rear work 40-992 40-1388
light) 40-1008
Bg008 10A fuse (front work 40-992 40-1388
lights) 40-1008

40-122
Wiring diagrams
Table 111
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bh001 Air conditioning com- [LNK] 40-1410
pressor fuse (10A)
Bh002 Trailer brake lights 40-895 40-1410
fuse (key-on power) 40-1206
(7.5A)
Bh003 Emergency fuse (di- 40-964 40-1410
rect) (20A)
Bh004 Seat compressor / 40-1137 40-1410
cigarette lighter fuse
(direct) (15A)
Bh005 Brake lights fuse 40-964 40-1410
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bh006 Instrument panel 40-1255 40-1410
fuse (direct) (5A)
Bh007 Hydraulic reverse 40-1206 40-1410
shuttle fuse (direct) 40-1255
(7.5A)
Bh008 Low beam head- 40-964 40-1410
lights fuse (15A)
Bh009 High beam head- 40-964 40-1410
lights fuse (15A)
Bh010 Ancillary fuse (lift) 40-1087 40-1410
(15A)
Bh011 Turn indicator lights 40-895 40-1410
fuse (key-on power) 40-964
(15A)
Bh012 Socket fuse (key-on 40-964 40-1410
power) (7.5A)
Bh013 Front loader fuse [LNK] 40-1410
(key-on power)
(7.5A)
Bh014 Fuse for work lights 40-1087 40-1410
on cab (key-on pow-
er) (15A)
Bh015 Fuse for low work 40-1087 40-1410
lights (key-on power)
(15A)
Bh016 Relay fuse (key-on 40-895 40-1410
power) (3A) 40-1206
40-1087
40-964
Bh017 Instrument panel 40-895 40-1410
fuse (key-on power) 40-1255
(10A) 40-1206
40-964
40-719
40-743
40-629
Bh018 Engine ECU fuse 40-629 40-1410
(key-on power) 40-1206
(7.5A) 40-1255
40-719

40-123
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bh019 RH sidelights fuse 40-964 40-1410
(7.5A)
Bh020 LH sidelights fuse 40-964 40-1410
(7.5A)
Bh021 MK1 relay fuse 30A 40-895 40-1410
40-1206
40-1087
Bh022 Protection fuse, FT 40-1206 40-1410
5-6-7-8 (30A)
Bh023 Fan/compressor [LNK] 40-1410
fuse (30 A)
Bh024 Starter fuse (40A) 40-629 40-1410
40-719
Bh025 Protection fuse [LNK] 40-1410
(40A)
Bh026 MK3 relay fuse 30A 40-895 40-1410
40-964
Bh027 Distributor 7-8 fuse [LNK] 40-1410
(5A)
Bh028 Power socket fuse [LNK] 40-1410
(30A)
Bh029 Not used [LNK] 40-1410
Bh030 Steering column 40-964 40-1410
stalk fuse - lights in- 40-1137
put (20A)
Bh031 Ventilation/heating [LNK] 40-1410
fuse (20A)

40-124
Wiring diagrams
40.2.10 - B - Fuses (AGROFARM 410 -> ZKDW470200TD30001)
ITA version

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1085 - Fuse box, ITA cab version

l Ba001 - Air conditioning compressor fuse (10A)
l Ba002 - Trailer brake lights fuse (key-on power) (7.5A)
l Ba003 - Emergency fuse (direct) (20A)
l Ba004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Ba005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Ba006 - Instrument panel fuse (direct) (5A)
l Ba007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Ba008 +30 cluster fuse (3A)
l Ba009 +30 Wolp fuse (10A)
l Ba010 - Ancillary fuse (lift) (15A)
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba012 - Socket fuse (key-on power) (7.5A)
l Ba013 - Front loader fuse (key-on power) (7.5A)
l Ba014 - Fuse for work lights on cab (key-on power) (15A)
l Ba015 - Fuse for low work lights (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba017 - Instrument panel fuse (key-on power) (10A)
l Ba018 - Engine ECU fuse (key-on power) (7.5A)
l Ba019 - RH sidelights fuse (7.5A)
l Ba020 - LH sidelights fuse (7.5A)
l Ba021 - MK1 relay fuse 30A
l Ba022 - Protection fuse, FT 5-6-7-8 (30A)

40-125
 Wiring diagrams

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1085 - Fuse box, ITA cab version

l Ba023 - Fan/compressor fuse (30A)
l Ba024 - Starter fuse (40A)
l Ba025 - Protection fuse (40A)
l Ba026 - MK3 relay fuse 30A
l Ba027 - Distributor 7-8 fuse (5A)
l Ba028 - Power socket fuse (key-on power) (30A)
l Ba029 - Not used
l Ba030 - Steering column stalk fuse - lights input (20A)
l Ba031 - Ventilation/heating fuse (20A)

40-126
Wiring diagrams

Bd026 Bd029

Bd022

Bd023
Bd021
Bd027 Bd030

Bd028 Bd031
Bd020

Bd019

Bd018

Bd017

Bd016

Bd015

Bd014

Bd013

Bd012

Bd011
Bd001

Bd002

Bd003

Bd004

Bd005

Bd006

Bd007

Bd008

Bd009

Bd010

Fig. 1086 - Fuse box, ITA platform version

l Bd001 - Air conditioning compressor fuse (10A)
l Bd002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bd003 - Emergency fuse (direct) (20A)
l Bd004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bd005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bd006 - Instrument panel fuse (direct) (5A)
l Bd007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bd008 - Cluster fuse +30 (3A)
l Bd009 - Wolp fuse +30 (10A)
l Bd010 - Ancillary fuse (lift) (15A)
l Bd011 - Turn indicator lights fuse (key-on power) (15A)
l Bd012 - Socket fuse (key-on power) (7.5A)
l Bd013 - Front loader fuse (key-on power) (7.5A)
l Bd014 - Fuse for work lights on cab (key-on power) (15A)
l Bd015 - Fuse for low work lights (key-on power) (15A)
l Bd016 - Relay fuse (key-on power) (3A)
l Bd017 - Instrument panel fuse (key-on power) (10A)
l Bd018 - Engine ECU fuse (key-on power) (7.5A)
l Bd019 - RH sidelights fuse (7.5A)
l Bd020 - LH sidelights fuse (7.5A)
l Bd021 - MK1 relay fuse 30A
l Bd022 - Protection fuse, FT 5-6-7-8 (30A)
l Bd023 - Fan/compressor fuse (30A)
l Bd024 - Starter fuse (40A)
l Bd025 - Protection fuse (40A)

40-127
 Wiring diagrams

Bd026 Bd029

Bd022

Bd023
Bd021
Bd027 Bd030

Bd028 Bd031
Bd020

Bd019

Bd018

Bd017

Bd016

Bd015

Bd014

Bd013

Bd012

Bd011
Bd001

Bd002

Bd003

Bd004

Bd005

Bd006

Bd007

Bd008

Bd009

Bd010

Fig. 1086 - Fuse box, ITA platform version

l Bd026 - MK3 relay fuse 30A
l Bd027 - Distributor 7-8 fuse (5A)
l Bd028 - Power socket fuse (30A)
l Bd029 - Not used
l Bd030 - Steering column stalk fuse - lights input (20A)
l Bd031 - Ventilation/heating fuse (20A)

40-128
Wiring diagrams
Table 112
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-600 40-1295
40-1258
40-1250
40-1237
40-1171
40-1151
40-1082
40-1033
40-984
40-948
40-922
40-889
40-877
40-816
40-791
40-758
40-755
40-750
40-738
40-723
40-714
40-701
40-671
40-665
40-625
40-637
B002 Preheat fuse 125A 40-600 40-1290
40-714
40-701
40-625
B003 0.900.0783.1 60A fuse 40-637 40-1295
40-1105
40-1033
40-984
40-816
40-758
40-755
40-750
40-671
40-665
B004 0.900.0783.1 60A fuse 40-637 40-1295
40-1237
40-1171
40-1151
40-1133
40-1105
40-1082
40-1033
40-984
40-948
40-922
40-889
40-877
40-816
40-791
40-758
40-755
40-750
40-671
40-665

40-129
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba001 Air conditioning com- 40-665 40-1331
pressor fuse (10A) 40-671
Ba002 Trailer brake lights 40-791 40-1331
fuse (key-on power) 40-877
(7.5A)
Ba003 Emergency fuse (di- 40-922 40-1331
rect) (20A)
Ba004 Seat compressor / 40-1105 40-1331
cigarette lighter fuse
(direct) (15A)
Ba005 Brake lights fuse 40-877 40-1331
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Ba006 Instrument panel 40-791 40-1331
fuse (direct) (5A) 40-1250
Ba007 Hydraulic reverse 40-791 40-1331
shuttle fuse (direct) 40-1250
(7.5A) 40-1151
Ba008 Low beam head- 40-922 40-1331
lights fuse (15A)
Ba009 High beam head- 40-922 40-1331
lights fuse (15A)
Ba010 Ancillary fuse (lift) [LNK] 40-1331
(15A)
Ba011 Turn indicator lights 40-637 40-1331
fuse (key-on power) 40-1033
(15A) 40-984
40-922
40-877
40-758
40-755
40-750
40-671
40-665
Ba012 Socket fuse (key-on [LNK] 40-1331
power) (7.5A)
Ba013 Front loader fuse [LNK] 40-1331
(key-on power)
(7.5A)
Ba014 Fuse for work lights 40-984 40-1331
on cab (key-on pow- 40-1033
er) (15A)
Ba015 Fuse for low work 40-984 40-1331
lights (key-on power) 40-1033
(15A)

40-130
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba016 Relay fuse (key-on 40-637 40-1331
power) (3A) 40-1237
40-1151
40-1033
40-984
40-922
40-877
40-791
40-758
40-755
40-750
40-671
40-665
Ba017 Instrument panel 40-600 40-1331
fuse (key-on power) 40-1250
(10A) 40-1151
40-922
40-877
40-791
40-723
40-701
40-625
Ba018 Engine ECU fuse 40-600 40-1331
(key-on power) 40-1250
(7.5A) 40-1151
40-791
40-701
40-625
Ba019 RH sidelights fuse 40-922 40-1331
(7.5A)
Ba020 LH sidelights fuse 40-922 40-1331
(7.5A)
Ba021 MK1 relay fuse 30A 40-791 40-1331
40-1151
40-1033
40-984
40-877
Ba022 Protection fuse, FT 40-750 40-1331
5-6-7-8 (30A) 40-1033
40-984
40-758
40-755
Ba023 Fan/compressor 40-637 40-1331
fuse (30 A) 40-671
40-665
Ba024 Starter fuse (40A) 40-600 40-1331
40-1151
40-701
40-625
Ba025 Protection fuse 40-665 40-1331
(40A) 40-1105
40-1033
40-750
40-671

40-131
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba026 MK3 relay fuse 30A 40-637 40-1331
40-1237
40-1033
40-984
40-922
40-877
40-758
40-755
40-671
40-665
Ba027 Distributor 7-8 fuse 40-1237 40-1331
(5A)
Ba028 Power socket fuse [LNK] 40-1331
(30A)
Ba029 Not used [LNK] 40-1331
Ba030 Steering column 40-922 40-1331
stalk fuse - lights in- 40-1105
put (20A)
Ba031 Ventilation/heating 40-637 40-1331
fuse (20A) 40-671
40-665
Table 113
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bd001 Air conditioning com- [LNK] 40-1392
pressor fuse (10A)
Bd002 Trailer brake lights 40-816 40-1392
fuse (key-on power) 40-1171
(7.5A) 40-889
Bd003 Emergency fuse (di- 40-948 40-1392
rect) (20A)
Bd004 Seat compressor / 40-1133 40-1392
cigarette lighter fuse
(direct) (15A)
Bd005 Brake lights fuse [LNK] 40-1392
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bd006 Instrument panel 40-816 40-1392
fuse (direct) (5A) 40-1258
40-889
Bd007 Hydraulic reverse 40-816 40-1392
shuttle fuse (direct) 40-1258
(7.5A) 40-1171
Bd008 Low beam head- 40-948 40-1392
lights fuse (15A)
Bd009 High beam head- [LNK] 40-1392
lights fuse (15A)
Bd010 Ancillary fuse (lift) 40-1082 40-1392
(15A)
Bd011 Turn indicator lights 40-889 40-1392
fuse (key-on power)
(15A)
Bd012 Socket fuse (key-on [LNK] 40-1392
power) (7.5A)

40-132
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bd013 Front loader fuse [LNK] 40-1392
(key-on power)
(7.5A)
Bd014 Fuse for work lights 40-1082 40-1392
on cab (key-on pow-
er) (15A)
Bd015 Fuse for low work 40-1082 40-1392
lights (key-on power)
(15A)
Bd016 Relay fuse (key-on 40-816 40-1392
power) (3A) 40-1171
40-1082
40-948
40-889
Bd017 Instrument panel 40-714 40-1392
fuse (key-on power) 40-1258
(10A) 40-1171
40-948
40-889
40-816
40-738
Bd018 Engine ECU fuse 40-714 40-1392
(key-on power) 40-1258
(7.5A) 40-1171
40-816
Bd019 RH sidelights fuse 40-948 40-1392
(7.5A)
Bd020 LH sidelights fuse 40-948 40-1392
(7.5A)
Bd021 MK1 relay fuse 30A 40-816 40-1392
40-1171
40-1082
40-889
Bd022 Protection fuse, FT 40-1171 40-1392
5-6-7-8 (30A)
Bd023 Fan/compressor [LNK] 40-1392
fuse (30 A)
Bd024 Starter fuse (40A) 40-714 40-1392
Bd025 Protection fuse [LNK] 40-1392
(40A)
Bd026 MK3 relay fuse 30A 40-889 40-1392
40-948
Bd027 Distributor 7-8 fuse [LNK] 40-1392
(5A)
Bd028 Power socket fuse [LNK] 40-1392
(30A)
Bd029 Not used [LNK] 40-1392
Bd030 Steering column 40-948 40-1392
stalk fuse - lights in- 40-1133
put (20A)
Bd031 Ventilation/heating [LNK] 40-1392
fuse (20A)

40-133
 Wiring diagrams
Table 114
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1033 40-1301
(10A - Rotating bea-
con)
Be002 Fuse 2 in fuse box F 40-1105 40-1301
(5A - Radio)
Be003 Fuse 3 in fuse box F 40-671 40-1301
(30A - Climate con-
trol)
Be005 Fuse 5 in fuse box F 40-750 40-1301
(7.5A - Windscreen
wiper)
Be006 Fuse 6 in fuse box F 40-750 40-1301
(7.5A - Rear screen
wiper)
Be007 Fuse 7 in fuse box 40-1033 40-1301
F (10A - Front work
lights)
Be008 Fuse 8 in fuse box 40-1033 40-1301
F (10A - Rear work
lights)
Bg001 10A fuse (beacon) 40-984 40-1388
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-665 40-1388
and climate control)
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)
Bg007 10A fuse (rear work 40-984 40-1388
light)
Bg008 10A fuse (front work 40-984 40-1388
lights)

40-134
Wiring diagrams
USA version

Bb026 Bb029

Bb022

Bb023
Bb021
Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1087 - Fuse box, USA cab version

l Bb001 - Air conditioning compressor fuse (10A)
l Bb002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bb003 - Emergency fuse (direct) (20A)
l Bb004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bb005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bb006 - Instrument panel fuse (direct) (5A)
l Bb007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bb008 - Cluster fuse +30 (3A)
l Bb009 - Wolp fuse +30 (10A)
l Bb010 - Ancillary fuse (lift) (15A)
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb012 - Socket fuse (key-on power) (7.5A)
l Bb013 - Front loader fuse (key-on power) (7.5A)
l Bb014 - Fuse for work lights on cab (key-on power) (15A)
l Bb015 - Fuse for low work lights (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb017 - Instrument panel fuse (key-on power) (10A)
l Bb018 - Engine ECU fuse (key-on power) (7.5A)
l Bb019 - RH sidelights fuse (7.5A)
l Bb020 - LH sidelights fuse (7.5A)
l Bb021 - MK1 relay fuse 30A
l Bb022- Protection fuse, FT 5-6-7-8 (30A)
l Bb023 - Fan/compressor fuse (30A)

40-135
 Wiring diagrams

Bb026 Bb029

Bb022

Bb023
Bb021
Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1087 - Fuse box, USA cab version

l Bb024 - Starter fuse (40A)
l Bb025 - Protection fuse (40A)
l Bb026 - MK3 relay fuse 30A
l Bb027 - Distributor 7-8 fuse (5A)
l Bb028 - Power socket fuse (30A)
l Bb029 - Not used
l Bb030 - Steering column stalk fuse - lights input (20A)
l Bb031 - Ventilation/heating fuse (20A)

40-136
Wiring diagrams

Bh026 Bh029

Bh022

Bh023
Bh021
Bh027 Bh030

Bh028 Bh031
Bh020

Bh019

Bh018

Bh017

Bh016

Bh015

Bh014

Bh013

Bh012

Bh011
Bh001

Bh002

Bh003

Bh004

Bh005

Bh006

Bh007

Bh008

Bh009

Bh010

Fig. 1088 - Fuse box, USA platform version

l Bh001 - Air conditioning compressor fuse (10A)
l Bh002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bh003 - Emergency fuse (direct) (20A)
l Bh004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bh005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bh006 - Instrument panel fuse (direct) (5A)
l Bh007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bh008 - Cluster fuse +30 (3A)
l Bh009 - Wolp fuse +30 (10A)
l Bh010 - Ancillary fuse (lift) (15A)
l Bh011 - Turn indicator lights fuse (key-on power) (15A)
l Bh012 - Socket fuse (key-on power) (7.5A)
l Bh013 - Front loader fuse (key-on power) (7.5A)
l Bh014 - Fuse for work lights on cab (key-on power) (15A)
l Bh015 - Fuse for low work lights (key-on power) (15A)
l Bh016 - Relay fuse (key-on power) (3A)
l Bh017 - Instrument panel fuse (key-on power) (10A)
l Bh018 - Engine ECU fuse (key-on power) (7.5A)
l Bh019 - RH sidelights fuse (7.5A)
l Bh020 - LH sidelights fuse (7.5A)
l Bh021 - MK1 relay fuse 30A
l Bh022 - Protection fuse, FT 5-6-7-8 (30A)
l Bh023 - Fan/compressor fuse (30A)
l Bh024 - Starter fuse (40A)
l Bh025 - Protection fuse (40A)

40-137
 Wiring diagrams

Bh026 Bh029

Bh022

Bh023
Bh021
Bh027 Bh030

Bh028 Bh031
Bh020

Bh019

Bh018

Bh017

Bh016

Bh015

Bh014

Bh013

Bh012

Bh011
Bh001

Bh002

Bh003

Bh004

Bh005

Bh006

Bh007

Bh008

Bh009

Bh010

Fig. 1088 - Fuse box, USA platform version

l Bh026 - MK3 relay fuse 30A
l Bh027 - Distributor 7-8 fuse (5A)
l Bh028 - Power socket fuse (30A)
l Bh029 - Not used
l Bh030 - Steering column stalk fuse - lights input (20A)
l Bh031 - Ventilation/heating fuse (20A)

40-138
Wiring diagrams
Table 115
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-608 40-1295
40-1240
40-1211
40-1192
40-1093
40-1050
40-1001
40-959
40-935
40-895
40-882
40-764
40-769
40-772
40-743
40-728
40-719
40-705
40-683
40-677
40-647
40-633
40-1258
40-1250
B002 Preheat fuse 125A 40-608 40-1290
40-719
40-705
40-633
B003 0.900.0783.1 60A fuse 40-647 40-1295
40-1115
40-1050
40-1001
40-764
40-769
40-772
40-683
40-677
B004 0.900.0783.1 60A fuse 40-647 40-1295
40-1240
40-1211
40-1192
40-1141
40-1115
40-1093
40-1050
40-1001
40-959
40-935
40-895
40-882
40-852
40-834
40-764
40-769
40-772
40-683
40-677

40-139
 Wiring diagrams
Table 116
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb001 Air conditioning com- 40-683 40-1347
pressor fuse (10A) 40-677
Bb002 Trailer brake lights 40-882 40-1347
fuse (key-on power) 40-1192
(7.5A)
Bb003 Emergency fuse (di- 40-935 40-1347
rect) (20A)
Bb004 Seat compressor / 40-1115 40-1347
cigarette lighter fuse
(direct) (15A)
Bb005 Brake lights fuse 40-935 40-1347
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bb006 Instrument panel 40-1250 40-1347
fuse (direct) (5A) 40-834
Bb007 Hydraulic reverse 40-1250 40-1347
shuttle fuse (direct) 40-1192
(7.5A)
Bb008 Low beam head- 40-935 40-1347
lights fuse (15A)
Bb009 High beam head- 40-935 40-1347
lights fuse (15A)
Bb010 Ancillary fuse (lift) [LNK] 40-1347
(15A)
Bb011 Turn indicator lights 40-647 40-1347
fuse (key-on power) 40-1050
(15A) 40-1001
40-935
40-882
40-764
40-769
40-772
40-683
40-677
Bb012 Socket fuse (key-on 40-935 40-1347
power) (7.5A)
Bb013 Front loader fuse [LNK] 40-1347
(key-on power)
(7.5A)
Bb014 Fuse for work lights 40-1001 40-1347
on cab (key-on pow- 40-1050
er) (15A)
Bb015 Fuse for low work 40-1001 40-1347
lights (key-on power) 40-1050
(15A)

40-140
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb016 Relay fuse (key-on 40-647 40-1347
power) (3A) 40-1240
40-1192
40-1050
40-1001
40-935
40-882
40-834
40-764
40-769
40-772
40-683
40-677
Bb017 Instrument panel 40-1250 40-1347
fuse (key-on power) 40-1192
(10A) 40-935
40-882
40-834
40-728
40-705
40-608
Bb018 Engine ECU fuse 40-1250 40-1347
(key-on power) 40-1192
(7.5A) 40-705
40-608
Bb019 RH sidelights fuse 40-935 40-1347
(7.5A)
Bb020 LH sidelights fuse 40-935 40-1347
(7.5A)
Bb021 MK1 relay fuse 30A 40-834 40-1347
40-1192
40-1050
40-1001
40-882
Bb022 Protection fuse, FT 40-764 40-1347
5-6-7-8 (30A) 40-1050
40-1001
40-834
40-769
40-772
Bb023 Fan/compressor 40-647 40-1347
fuse (30 A) 40-683
40-677
Bb024 Starter fuse (40A) 40-608 40-1347
40-1192
40-705
Bb025 Protection fuse 40-683 40-1347
(40A) 40-1115
40-1050
40-1001
40-677

40-141
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb026 MK3 relay fuse 30A 40-647 40-1347
40-1240
40-1050
40-1001
40-935
40-882
40-764
40-769
40-772
40-683
40-677
Bb027 Distributor 7-8 fuse 40-1240 40-1347
(5A)
Bb028 Power socket fuse [LNK] 40-1347
(30A)
Bb029 Not used [LNK] 40-1347
Bb030 Steering column 40-935 40-1347
stalk fuse - lights in- 40-1115
put (20A)
Bb031 Ventilation/heating 40-647 40-1347
fuse (20A) 40-683
40-677

Table 117
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1050 40-1301
(10A - Rotating bea-
con)
Be002 Fuse 2 in fuse box F 40-1115 40-1301
(5A - Radio)
Be003 Fuse 3 in fuse box F 40-677 40-1301
(30A - Climate con-
trol)
Be005 Fuse 5 in fuse box F 40-764 40-1301
(7.5A - Windscreen
wiper)
Be006 Fuse 6 in fuse box F 40-764 40-1301
(7.5A - Rear screen
wiper)
Be007 Fuse 7 in fuse box 40-1050 40-1301
F (10A - Front work
lights)
Be008 Fuse 8 in fuse box 40-1050 40-1301
F (10A - Rear work
lights)
Bg001 10A fuse (beacon) 40-1001 40-1388
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-683 40-1388
and climate control)
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)
Bg007 10A fuse (rear work 40-1001 40-1388
light)

40-142
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bg008 10A fuse (front work 40-1001 40-1388
lights)
Table 118
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bh001 Air conditioning com- [LNK] 40-1410
pressor fuse (10A)
Bh002 Trailer brake lights 40-852 40-1410
fuse (key-on power) 40-1211
(7.5A) 40-895
Bh003 Emergency fuse (di- 40-852 40-1410
rect) (20A) 40-959
Bh004 Seat compressor / 40-1141 40-1410
cigarette lighter fuse
(direct) (15A)
Bh005 Brake lights fuse 40-959 40-1410
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bh006 Instrument panel 40-1258 40-1410
fuse (direct) (5A) 40-852
Bh007 Hydraulic reverse 40-1258 40-1410
shuttle fuse (direct) 40-1211
(7.5A) 40-852
Bh008 Low beam head- 40-959 40-1410
lights fuse (15A)
Bh009 High beam head- 40-959 40-1410
lights fuse (15A)
Bh010 Ancillary fuse (lift) 40-1093 40-1410
(15A)
Bh011 Turn indicator lights 40-895 40-1410
fuse (key-on power) 40-959
(15A)
Bh012 Socket fuse (key-on 40-959 40-1410
power) (7.5A)
Bh013 Front loader fuse [LNK] 40-1410
(key-on power)
(7.5A)
Bh014 Fuse for work lights 40-1093 40-1410
on cab (key-on pow-
er) (15A)
Bh015 Fuse for low work 40-1093 40-1410
lights (key-on power)
(15A)
Bh016 Relay fuse (key-on 40-852 40-1410
power) (3A) 40-1211
40-1093
40-959
40-895

40-143
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bh017 Instrument panel 40-1258 40-1410
fuse (key-on power) 40-1211
(10A) 40-959
40-895
40-852
40-743
40-719
40-633
Bh018 Engine ECU fuse 40-1258 40-1410
(key-on power) 40-1211
(7.5A) 40-852
40-719
40-633
Bh019 RH sidelights fuse 40-959 40-1410
(7.5A)
Bh020 LH sidelights fuse 40-959 40-1410
(7.5A)
Bh021 MK1 relay fuse 30A 40-852 40-1410
40-1211
40-1093
40-895
Bh022 Protection fuse, FT 40-1211 40-1410
5-6-7-8 (30A)
Bh023 Fan/compressor [LNK] 40-1410
fuse (30 A)
Bh024 Starter fuse (40A) 40-633 40-1410
40-719
Bh025 Protection fuse [LNK] 40-1410
(40A)
Bh026 MK3 relay fuse 30A 40-895 40-1410
40-959
Bh027 Distributor 7-8 fuse [LNK] 40-1410
(5A)
Bh028 Power socket fuse [LNK] 40-1410
(30A)
Bh029 Not used [LNK] 40-1410
Bh030 Steering column 40-959 40-1410
stalk fuse - lights in- 40-1141
put (20A)
Bh031 Ventilation/heating [LNK] 40-1410
fuse (20A)

40-144
Wiring diagrams
40.2.11 - B - Fuses (AGROFARM 420 -> ZKDW510200TD30001)
ITA version

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1089 - Fuse box, cab version

l Ba001 - Air conditioning compressor fuse (10A)
l Ba002 - Trailer brake lights fuse (key-on power) (7.5A)
l Ba003 - Emergency fuse (direct) (20A)
l Ba004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Ba005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Ba006 - Instrument panel fuse (direct) (5A)
l Ba007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Ba008 +30 cluster fuse (3A)
l Ba009 +30 Wolp fuse (10A)
l Ba010 - Ancillary fuse (lift) (15A)
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba012 - Socket fuse (key-on power) (7.5A)
l Ba013 - Front loader fuse (key-on power) (7.5A)
l Ba014 - Fuse for work lights on cab (key-on power) (15A)
l Ba015 - Fuse for low work lights (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba017 - Instrument panel fuse (key-on power) (10A)
l Ba018 - Engine ECU fuse (key-on power) (7.5A)
l Ba019 - RH sidelights fuse (7.5A)
l Ba020 - LH sidelights fuse (7.5A)
l Ba021 - MK1 relay fuse 30A
l Ba022 - Protection fuse, FT 5-6-7-8 (30A)

40-145
 Wiring diagrams

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1089 - Fuse box, cab version

l Ba023 - Fan/compressor fuse (30A)
l Ba024 - Starter fuse (40A)
l Ba025 - Protection fuse (40A)
l Ba026 - MK3 relay fuse 30A
l Ba027 - Distributor 7-8 fuse (5A)
l Ba028 - Power socket fuse (key-on power) (30A)
l Ba029 - Not used
l Ba030 - Steering column stalk fuse - lights input (20A)
l Ba031 - Ventilation/heating fuse (20A)

40-146
Wiring diagrams

Bd026 Bd029

Bd022

Bd023
Bd021
Bd027 Bd030

Bd028 Bd031
Bd020

Bd019

Bd018

Bd017

Bd016

Bd015

Bd014

Bd013

Bd012

Bd011
Bd001

Bd002

Bd003

Bd004

Bd005

Bd006

Bd007

Bd008

Bd009

Bd010

Fig. 1090 - Fuse box, platform version

l Bd001 - Air conditioning compressor fuse (10A)
l Bd002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bd003 - Emergency fuse (direct) (20A)
l Bd004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bd005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bd006 - Instrument panel fuse (direct) (5A)
l Bd007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bd008 - Cluster fuse +30 (3A)
l Bd009 - Wolp fuse +30 (10A)
l Bd010 - Ancillary fuse (lift) (15A)
l Bd011 - Turn indicator lights fuse (key-on power) (15A)
l Bd012 - Socket fuse (key-on power) (7.5A)
l Bd013 - Front loader fuse (key-on power) (7.5A)
l Bd014 - Fuse for work lights on cab (key-on power) (15A)
l Bd015 - Fuse for low work lights (key-on power) (15A)
l Bd016 - Relay fuse (key-on power) (3A)
l Bd017 - Instrument panel fuse (key-on power) (10A)
l Bd018 - Engine ECU fuse (key-on power) (7.5A)
l Bd019 - RH sidelights fuse (7.5A)
l Bd020 - LH sidelights fuse (7.5A)
l Bd021 - MK1 relay fuse 30A
l Bd022 - Protection fuse, FT 5-6-7-8 (30A)
l Bd023 - Fan/compressor fuse (30A)
l Bd024 - Starter fuse (40A)
l Bd025 - Protection fuse (40A)

40-147
 Wiring diagrams

Bd026 Bd029

Bd022

Bd023
Bd021
Bd027 Bd030

Bd028 Bd031
Bd020

Bd019

Bd018

Bd017

Bd016

Bd015

Bd014

Bd013

Bd012

Bd011
Bd001

Bd002

Bd003

Bd004

Bd005

Bd006

Bd007

Bd008

Bd009

Bd010

Fig. 1090 - Fuse box, platform version

l Bd026 - MK3 relay fuse 30A
l Bd027 - Distributor 7-8 fuse (5A)
l Bd028 - Power socket fuse (30A)
l Bd029 - Not used
l Bd030 - Steering column stalk fuse - lights input (20A)
l Bd031 - Ventilation/heating fuse (20A)

40-148
Wiring diagrams
Table 119
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-600 40-1295
40-1258
40-1250
40-1237
40-1178
40-1158
40-1082
40-1033
40-984
40-948
40-922
40-889
40-877
40-816
40-791
40-758
40-755
40-750
40-738
40-723
40-714
40-701
40-671
40-665
40-625
40-637
B002 Preheat fuse 125A 40-600 40-1290
40-714
40-701
40-625
B003 0.900.0783.1 60A fuse 40-637 40-1295
40-1105
40-1033
40-984
40-816
40-758
40-755
40-750
40-671
40-665
B004 0.900.0783.1 60A fuse 40-637 40-1295
40-1237
40-1178
40-1158
40-1133
40-1105
40-1082
40-1033
40-984
40-948
40-922
40-889
40-877
40-816
40-791
40-758
40-755
40-750
40-671
40-665

40-149
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba001 Air conditioning com- 40-665 40-1331
pressor fuse (10A) 40-671
Ba002 Trailer brake lights 40-791 40-1331
fuse (key-on power) 40-877
(7.5A)
Ba003 Emergency fuse (di- 40-922 40-1331
rect) (20A)
Ba004 Seat compressor / 40-1105 40-1331
cigarette lighter fuse
(direct) (15A)
Ba005 Brake lights fuse 40-877 40-1331
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Ba006 Instrument panel 40-791 40-1331
fuse (direct) (5A) 40-1250
Ba007 Hydraulic reverse 40-791 40-1331
shuttle fuse (direct) 40-1250
(7.5A) 40-1158
Ba008 Low beam head- 40-922 40-1331
lights fuse (15A)
Ba009 High beam head- 40-922 40-1331
lights fuse (15A)
Ba010 Ancillary fuse (lift) [LNK] 40-1331
(15A)
Ba011 Turn indicator lights 40-637 40-1331
fuse (key-on power) 40-1033
(15A) 40-984
40-922
40-877
40-758
40-755
40-750
40-671
40-665
Ba012 Socket fuse (key-on [LNK] 40-1331
power) (7.5A)
Ba013 Front loader fuse [LNK] 40-1331
(key-on power)
(7.5A)
Ba014 Fuse for work lights 40-984 40-1331
on cab (key-on pow- 40-1033
er) (15A)
Ba015 Fuse for low work 40-984 40-1331
lights (key-on power) 40-1033
(15A)

40-150
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba016 Relay fuse (key-on 40-637 40-1331
power) (3A) 40-1237
40-1158
40-1033
40-984
40-922
40-877
40-791
40-758
40-755
40-750
40-671
40-665
Ba017 Instrument panel 40-600 40-1331
fuse (key-on power) 40-1250
(10A) 40-1158
40-922
40-877
40-791
40-723
40-701
40-625
Ba018 Engine ECU fuse 40-600 40-1331
(key-on power) 40-1250
(7.5A) 40-1158
40-791
40-701
40-625
Ba019 RH sidelights fuse 40-922 40-1331
(7.5A)
Ba020 LH sidelights fuse 40-922 40-1331
(7.5A)
Ba021 MK1 relay fuse 30A 40-791 40-1331
40-1158
40-1033
40-984
40-877
Ba022 Protection fuse, FT 40-750 40-1331
5-6-7-8 (30A) 40-1033
40-984
40-758
40-755
Ba023 Fan/compressor 40-637 40-1331
fuse (30 A) 40-671
40-665
Ba024 Starter fuse (40A) 40-600 40-1331
40-1158
40-701
40-625
Ba025 Protection fuse 40-665 40-1331
(40A) 40-1105
40-1033
40-750
40-671

40-151
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba026 MK3 relay fuse 30A 40-637 40-1331
40-1237
40-1033
40-984
40-922
40-877
40-758
40-755
40-671
40-665
Ba027 Distributor 7-8 fuse 40-1237 40-1331
(5A)
Ba028 Power socket fuse [LNK] 40-1331
(30A)
Ba029 Not used [LNK] 40-1331
Ba030 Steering column 40-922 40-1331
stalk fuse - lights in- 40-1105
put (20A)
Ba031 Ventilation/heating 40-637 40-1331
fuse (20A) 40-671
40-665
Table 120
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bd001 Air conditioning com- [LNK] 40-1392
pressor fuse (10A)
Bd002 Trailer brake lights 40-816 40-1392
fuse (key-on power) 40-1178
(7.5A) 40-889
Bd003 Emergency fuse (di- 40-948 40-1392
rect) (20A)
Bd004 Seat compressor / 40-1133 40-1392
cigarette lighter fuse
(direct) (15A)
Bd005 Brake lights fuse [LNK] 40-1392
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bd006 Instrument panel 40-816 40-1392
fuse (direct) (5A) 40-1258
40-889
Bd007 Hydraulic reverse 40-816 40-1392
shuttle fuse (direct) 40-1258
(7.5A) 40-1178
Bd008 Low beam head- 40-948 40-1392
lights fuse (15A)
Bd009 High beam head- [LNK] 40-1392
lights fuse (15A)
Bd010 Ancillary fuse (lift) 40-1082 40-1392
(15A)
Bd011 Turn indicator lights 40-889 40-1392
fuse (key-on power)
(15A)
Bd012 Socket fuse (key-on [LNK] 40-1392
power) (7.5A)

40-152
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bd013 Front loader fuse [LNK] 40-1392
(key-on power)
(7.5A)
Bd014 Fuse for work lights 40-1082 40-1392
on cab (key-on pow-
er) (15A)
Bd015 Fuse for low work 40-1082 40-1392
lights (key-on power)
(15A)
Bd016 Relay fuse (key-on 40-816 40-1392
power) (3A) 40-1178
40-1082
40-948
40-889
Bd017 Instrument panel 40-714 40-1392
fuse (key-on power) 40-1258
(10A) 40-1178
40-948
40-889
40-816
40-738
Bd018 Engine ECU fuse 40-714 40-1392
(key-on power) 40-1258
(7.5A) 40-1178
40-816
Bd019 RH sidelights fuse 40-948 40-1392
(7.5A)
Bd020 LH sidelights fuse 40-948 40-1392
(7.5A)
Bd021 MK1 relay fuse 30A 40-816 40-1392
40-1178
40-1082
40-889
Bd022 Protection fuse, FT 40-1178 40-1392
5-6-7-8 (30A)
Bd023 Fan/compressor [LNK] 40-1392
fuse (30 A)
Bd024 Starter fuse (40A) 40-714 40-1392
Bd025 Protection fuse [LNK] 40-1392
(40A)
Bd026 MK3 relay fuse 30A 40-889 40-1392
40-948
Bd027 Distributor 7-8 fuse [LNK] 40-1392
(5A)
Bd028 Power socket fuse [LNK] 40-1392
(30A)
Bd029 Not used [LNK] 40-1392
Bd030 Steering column 40-948 40-1392
stalk fuse - lights in- 40-1133
put (20A)
Bd031 Ventilation/heating [LNK] 40-1392
fuse (20A)

40-153
 Wiring diagrams
Table 121
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1033 40-1301
(10A - Rotating bea-
con)
Be002 Fuse 2 in fuse box F 40-1105 40-1301
(5A - Radio)
Be003 Fuse 3 in fuse box F 40-671 40-1301
(30A - Climate con-
trol)
Be005 Fuse 5 in fuse box F 40-750 40-1301
(7.5A - Windscreen
wiper)
Be006 Fuse 6 in fuse box F 40-750 40-1301
(7.5A - Rear screen
wiper)
Be007 Fuse 7 in fuse box 40-1033 40-1301
F (10A - Front work
lights)
Be008 Fuse 8 in fuse box 40-1033 40-1301
F (10A - Rear work
lights)
Bg001 10A fuse (beacon) 40-984 40-1388
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-665 40-1388
and climate control)
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)
Bg007 10A fuse (rear work 40-984 40-1388
light)
Bg008 10A fuse (front work 40-984 40-1388
lights)

40-154
Wiring diagrams
USA version

Bb026 Bb029

Bb022

Bb023
Bb021
Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1091 - Fuse box, cab version

l Bb001 - Air conditioning compressor fuse (10A)
l Bb002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bb003 - Emergency fuse (direct) (20A)
l Bb004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bb005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bb006 - Instrument panel fuse (direct) (5A)
l Bb007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bb008 - Cluster fuse +30 (3A)
l Bb009 - Wolp fuse +30 (10A)
l Bb010 - Ancillary fuse (lift) (15A)
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb012 - Socket fuse (key-on power) (7.5A)
l Bb013 - Front loader fuse (key-on power) (7.5A)
l Bb014 - Fuse for work lights on cab (key-on power) (15A)
l Bb015 - Fuse for low work lights (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb017 - Instrument panel fuse (key-on power) (10A)
l Bb018 - Engine ECU fuse (key-on power) (7.5A)
l Bb019 - RH sidelights fuse (7.5A)
l Bb020 - LH sidelights fuse (7.5A)
l Bb021 - MK1 relay fuse 30A
l Bb022- Protection fuse, FT 5-6-7-8 (30A)
l Bb023 - Fan/compressor fuse (30A)

40-155
 Wiring diagrams

Bb026 Bb029

Bb022

Bb023
Bb021
Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1091 - Fuse box, cab version

l Bb024 - Starter fuse (40A)
l Bb025 - Protection fuse (40A)
l Bb026 - MK3 relay fuse 30A
l Bb027 - Distributor 7-8 fuse (5A)
l Bb028 - Power socket fuse (30A)
l Bb029 - Not used
l Bb030 - Steering column stalk fuse - lights input (20A)
l Bb031 - Ventilation/heating fuse (20A)

40-156
Wiring diagrams

Bh026 Bh029

Bh022

Bh023
Bh021
Bh027 Bh030

Bh028 Bh031
Bh020

Bh019

Bh018

Bh017

Bh016

Bh015

Bh014

Bh013

Bh012

Bh011
Bh001

Bh002

Bh003

Bh004

Bh005

Bh006

Bh007

Bh008

Bh009

Bh010

Fig. 1092 - Fuse box, platform version

l Bh001 - Air conditioning compressor fuse (10A)
l Bh002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bh003 - Emergency fuse (direct) (20A)
l Bh004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bh005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bh006 - Instrument panel fuse (direct) (5A)
l Bh007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bh008 - Cluster fuse +30 (3A)
l Bh009 - Wolp fuse +30 (10A)
l Bh010 - Ancillary fuse (lift) (15A)
l Bh011 - Turn indicator lights fuse (key-on power) (15A)
l Bh012 - Socket fuse (key-on power) (7.5A)
l Bh013 - Front loader fuse (key-on power) (7.5A)
l Bh014 - Fuse for work lights on cab (key-on power) (15A)
l Bh015 - Fuse for low work lights (key-on power) (15A)
l Bh016 - Relay fuse (key-on power) (3A)
l Bh017 - Instrument panel fuse (key-on power) (10A)
l Bh018 - Engine ECU fuse (key-on power) (7.5A)
l Bh019 - RH sidelights fuse (7.5A)
l Bh020 - LH sidelights fuse (7.5A)
l Bh021 - MK1 relay fuse 30A
l Bh022 - Protection fuse, FT 5-6-7-8 (30A)
l Bh023 - Fan/compressor fuse (30A)
l Bh024 - Starter fuse (40A)
l Bh025 - Protection fuse (40A)

40-157
 Wiring diagrams

Bh026 Bh029

Bh022

Bh023
Bh021
Bh027 Bh030

Bh028 Bh031
Bh020

Bh019

Bh018

Bh017

Bh016

Bh015

Bh014

Bh013

Bh012

Bh011
Bh001

Bh002

Bh003

Bh004

Bh005

Bh006

Bh007

Bh008

Bh009

Bh010

Fig. 1092 - Fuse box, platform version

l Bh026 - MK3 relay fuse 30A
l Bh027 - Distributor 7-8 fuse (5A)
l Bh028 - Power socket fuse (30A)
l Bh029 - Not used
l Bh030 - Steering column stalk fuse - lights input (20A)
l Bh031 - Ventilation/heating fuse (20A)

40-158
Wiring diagrams
Table 122
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-608 40-1295
40-1240
40-1218
40-1199
40-1093
40-1050
40-1001
40-959
40-935
40-895
40-882
40-764
40-769
40-772
40-743
40-728
40-719
40-705
40-683
40-677
40-647
40-633
40-1258
40-1250
B002 Preheat fuse 125A 40-608 40-1290
40-719
40-705
40-633
B003 0.900.0783.1 60A fuse 40-647 40-1295
40-1115
40-1050
40-1001
40-764
40-769
40-772
40-683
40-677
B004 0.900.0783.1 60A fuse 40-647 40-1295
40-1240
40-1218
40-1199
40-1141
40-1115
40-1093
40-1050
40-1001
40-959
40-935
40-895
40-882
40-852
40-834
40-764
40-769
40-772
40-683
40-677

40-159
 Wiring diagrams
Table 123
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb001 Air conditioning com- 40-683 40-1347
pressor fuse (10A) 40-677
Bb002 Trailer brake lights 40-882 40-1347
fuse (key-on power) 40-1199
(7.5A)
Bb003 Emergency fuse (di- 40-935 40-1347
rect) (20A)
Bb004 Seat compressor / 40-1115 40-1347
cigarette lighter fuse
(direct) (15A)
Bb005 Brake lights fuse 40-935 40-1347
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bb006 Instrument panel 40-1250 40-1347
fuse (direct) (5A) 40-834
Bb007 Hydraulic reverse 40-1250 40-1347
shuttle fuse (direct) 40-1199
(7.5A)
Bb008 Low beam head- 40-935 40-1347
lights fuse (15A)
Bb009 High beam head- 40-935 40-1347
lights fuse (15A)
Bb010 Ancillary fuse (lift) [LNK] 40-1347
(15A)
Bb011 Turn indicator lights 40-647 40-1347
fuse (key-on power) 40-1050
(15A) 40-1001
40-935
40-882
40-764
40-769
40-772
40-683
40-677
Bb012 Socket fuse (key-on 40-935 40-1347
power) (7.5A)
Bb013 Front loader fuse [LNK] 40-1347
(key-on power)
(7.5A)
Bb014 Fuse for work lights 40-1001 40-1347
on cab (key-on pow- 40-1050
er) (15A)
Bb015 Fuse for low work 40-1001 40-1347
lights (key-on power) 40-1050
(15A)

40-160
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb016 Relay fuse (key-on 40-647 40-1347
power) (3A) 40-1240
40-1199
40-1050
40-1001
40-935
40-882
40-834
40-764
40-769
40-772
40-683
40-677
Bb017 Instrument panel 40-1250 40-1347
fuse (key-on power) 40-1199
(10A) 40-935
40-882
40-834
40-728
40-705
40-608
Bb018 Engine ECU fuse 40-1250 40-1347
(key-on power) 40-1199
(7.5A) 40-705
40-608
Bb019 RH sidelights fuse 40-935 40-1347
(7.5A)
Bb020 LH sidelights fuse 40-935 40-1347
(7.5A)
Bb021 MK1 relay fuse 30A 40-834 40-1347
40-1199
40-1050
40-1001
40-882
Bb022 Protection fuse, FT 40-764 40-1347
5-6-7-8 (30A) 40-1050
40-1001
40-834
40-769
40-772
Bb023 Fan/compressor 40-647 40-1347
fuse (30 A) 40-683
40-677
Bb024 Starter fuse (40A) 40-608 40-1347
40-1199
40-705
Bb025 Protection fuse 40-683 40-1347
(40A) 40-1115
40-1050
40-1001
40-677

40-161
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb026 MK3 relay fuse 30A 40-647 40-1347
40-1240
40-1050
40-1001
40-935
40-882
40-764
40-769
40-772
40-683
40-677
Bb027 Distributor 7-8 fuse 40-1240 40-1347
(5A)
Bb028 Power socket fuse [LNK] 40-1347
(30A)
Bb029 Not used [LNK] 40-1347
Bb030 Steering column 40-935 40-1347
stalk fuse - lights in- 40-1115
put (20A)
Bb031 Ventilation/heating 40-647 40-1347
fuse (20A) 40-683
40-677

Table 124
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1050 40-1301
(10A - Rotating bea-
con)
Be002 Fuse 2 in fuse box F 40-1115 40-1301
(5A - Radio)
Be003 Fuse 3 in fuse box F 40-677 40-1301
(30A - Climate con-
trol)
Be005 Fuse 5 in fuse box F 40-764 40-1301
(7.5A - Windscreen
wiper)
Be006 Fuse 6 in fuse box F 40-764 40-1301
(7.5A - Rear screen
wiper)
Be007 Fuse 7 in fuse box 40-1050 40-1301
F (10A - Front work
lights)
Be008 Fuse 8 in fuse box 40-1050 40-1301
F (10A - Rear work
lights)
Bg001 10A fuse (beacon) 40-1001 40-1388
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-683 40-1388
and climate control)
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)
Bg007 10A fuse (rear work 40-1001 40-1388
light)

40-162
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bg008 10A fuse (front work 40-1001 40-1388
lights)
Table 125
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bh001 Air conditioning com- [LNK] 40-1410
pressor fuse (10A)
Bh002 Trailer brake lights 40-852 40-1410
fuse (key-on power) 40-1218
(7.5A) 40-895
Bh003 Emergency fuse (di- 40-852 40-1410
rect) (20A) 40-959
Bh004 Seat compressor / 40-1141 40-1410
cigarette lighter fuse
(direct) (15A)
Bh005 Brake lights fuse 40-959 40-1410
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bh006 Instrument panel 40-1258 40-1410
fuse (direct) (5A) 40-852
Bh007 Hydraulic reverse 40-1258 40-1410
shuttle fuse (direct) 40-1218
(7.5A) 40-852
Bh008 Low beam head- 40-959 40-1410
lights fuse (15A)
Bh009 High beam head- 40-959 40-1410
lights fuse (15A)
Bh010 Ancillary fuse (lift) 40-1093 40-1410
(15A)
Bh011 Turn indicator lights 40-895 40-1410
fuse (key-on power) 40-959
(15A)
Bh012 Socket fuse (key-on 40-959 40-1410
power) (7.5A)
Bh013 Front loader fuse [LNK] 40-1410
(key-on power)
(7.5A)
Bh014 Fuse for work lights 40-1093 40-1410
on cab (key-on pow-
er) (15A)
Bh015 Fuse for low work 40-1093 40-1410
lights (key-on power)
(15A)
Bh016 Relay fuse (key-on 40-852 40-1410
power) (3A) 40-1218
40-1093
40-959
40-895

40-163
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bh017 Instrument panel 40-1258 40-1410
fuse (key-on power) 40-1218
(10A) 40-959
40-895
40-852
40-743
40-719
40-633
Bh018 Engine ECU fuse 40-1258 40-1410
(key-on power) 40-1218
(7.5A) 40-852
40-719
40-633
Bh019 RH sidelights fuse 40-959 40-1410
(7.5A)
Bh020 LH sidelights fuse 40-959 40-1410
(7.5A)
Bh021 MK1 relay fuse 30A 40-852 40-1410
40-1218
40-1093
40-895
Bh022 Protection fuse, FT 40-1218 40-1410
5-6-7-8 (30A)
Bh023 Fan/compressor [LNK] 40-1410
fuse (30 A)
Bh024 Starter fuse (40A) 40-633 40-1410
40-719
Bh025 Protection fuse [LNK] 40-1410
(40A)
Bh026 MK3 relay fuse 30A 40-895 40-1410
40-959
Bh027 Distributor 7-8 fuse [LNK] 40-1410
(5A)
Bh028 Power socket fuse [LNK] 40-1410
(30A)
Bh029 Not used [LNK] 40-1410
Bh030 Steering column 40-959 40-1410
stalk fuse - lights in- 40-1141
put (20A)
Bh031 Ventilation/heating [LNK] 40-1410
fuse (20A)

40-164
Wiring diagrams
40.2.12 - B - Fuses (AGROFARM 430 -> ZKDW550200TD30001)
ITA version

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1093 - Fuse box, cab version

l Ba001 - Air conditioning compressor fuse (10A)
l Ba002 - Trailer brake lights fuse (key-on power) (7.5A)
l Ba003 - Emergency fuse (direct) (20A)
l Ba004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Ba005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Ba006 - Instrument panel fuse (direct) (5A)
l Ba007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Ba008 +30 cluster fuse (3A)
l Ba009 +30 Wolp fuse (10A)
l Ba010 - Ancillary fuse (lift) (15A)
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba012 - Socket fuse (key-on power) (7.5A)
l Ba013 - Front loader fuse (key-on power) (7.5A)
l Ba014 - Fuse for work lights on cab (key-on power) (15A)
l Ba015 - Fuse for low work lights (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba017 - Instrument panel fuse (key-on power) (10A)
l Ba018 - Engine ECU fuse (key-on power) (7.5A)
l Ba019 - RH sidelights fuse (7.5A)
l Ba020 - LH sidelights fuse (7.5A)
l Ba021 - MK1 relay fuse 30A
l Ba022 - Protection fuse, FT 5-6-7-8 (30A)

40-165
 Wiring diagrams

Ba026 Ba029

Ba022

Ba023
Ba021
Ba027 Ba030

Ba028 Ba031
Ba020

Ba019

Ba018

Ba017

Ba016

Ba015

Ba014

Ba013

Ba012

Ba011
Ba001

Ba002

Ba003

Ba004

Ba005

Ba006

Ba007

Ba008

Ba009

Ba010

Fig. 1093 - Fuse box, cab version

l Ba023 - Fan/compressor fuse (30A)
l Ba024 - Starter fuse (40A)
l Ba025 - Protection fuse (40A)
l Ba026 - MK3 relay fuse 30A
l Ba027 - Distributor 7-8 fuse (5A)
l Ba028 - Power socket fuse (key-on power) (30A)
l Ba029 - Not used
l Ba030 - Steering column stalk fuse - lights input (20A)
l Ba031 - Ventilation/heating fuse (20A)

40-166
Wiring diagrams

Bc026 Bc029

Bc022

Bc023
Bc021
Bc027 Bc030

Bc028 Bc031
Bc020

Bc019

Bc018

Bc017

Bc016

Bc015

Bc014

Bc013

Bc012

Bc011
Bc001

Bc002

Bc003

Bc004

Bc005

Bc006

Bc007

Bc008

Bc009

Bc010

Fig. 1094 - Fuse box, cab version with electronic lift

l Bc001 - Air conditioning compressor fuse (10A)
l Bc002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bc003 - Emergency fuse (direct) (20A)
l Bc004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bc005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bc006 - Instrument panel fuse (direct) (5A)
l Bc007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bc008 - Cluster fuse +30 (3A)
l Bc009 - Wolp fuse +30 (10A)
l Bc010 - Ancillary fuse (lift) (15A)
l Bc011 - Turn indicator lights fuse (key-on power) (15A)
l Bc012 - Socket fuse (key-on power) (7.5A)
l Bc013 - Front loader fuse (key-on power) (7.5A)
l Bc014 - Fuse for work lights on cab (key-on power) (15A)
l Bc015 - Fuse for low work lights (key-on power) (15A)
l Bc016 - Relay fuse (key-on power) (3A)
l Bc017 - Instrument panel fuse (key-on power) (10A)
l Bc018 - Engine ECU fuse (key-on power) (7.5A)
l Bc019 - RH sidelights fuse (7.5A)
l Bc020 - LH sidelights fuse (7.5A)
l Bc021 - MK1 relay fuse 30A
l Bc022 - Protection fuse, FT 5-6-7-8 (30A)
l Bc023 - Fan/compressor fuse (30A)
l Bc024 - Starter fuse (40A)
l Bc025 - Protection fuse (40A)

40-167
 Wiring diagrams

Bc026 Bc029

Bc022

Bc023
Bc021
Bc027 Bc030

Bc028 Bc031
Bc020

Bc019

Bc018

Bc017

Bc016

Bc015

Bc014

Bc013

Bc012

Bc011
Bc001

Bc002

Bc003

Bc004

Bc005

Bc006

Bc007

Bc008

Bc009

Bc010

Fig. 1094 - Fuse box, cab version with electronic lift

l Bc026 - MK3 relay fuse 30A
l Bc027 - Distributor 7-8 fuse (5A)
l Bc028 - Power socket fuse (30A)
l Bc029 - Not used
l Bc030 - Steering column stalk fuse - lights input (20A)
l Bc031 - Ventilation/heating fuse (20A)

40-168
Wiring diagrams
Table 126
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-600 40-1295
40-1266
40-1243
40-1269
40-1231
40-1067
40-1016
40-970
40-902
40-870
40-778
40-783
40-734
40-710
40-657
40-689
40-695
40-616
40-1250
40-1237
40-1158
40-1033
40-984
40-922
40-889
40-877
40-799
40-755
40-750
40-723
40-701
40-671
40-665
40-637
B002 Preheat fuse 125A 40-600 40-1290
40-710
40-616
40-701
B003 0.900.0783.1 60A fuse 40-637 40-1295
40-1125
40-1067
40-1016
40-778
40-783
40-689
40-695
40-657
40-1105
40-1033
40-984
40-755
40-750
40-671
40-665

40-169
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B004 0.900.0783.1 60A fuse 40-637 40-1295
40-1266
40-1243
40-1269
40-1231
40-1125
40-1067
40-1016
40-970
40-902
40-870
40-778
40-783
40-689
40-695
40-657
40-1237
40-1158
40-1105
40-1033
40-984
40-922
40-889
40-877
40-799
40-755
40-750
40-671
40-665
Ba001 Air conditioning com- 40-665 40-1331
pressor fuse (10A) 40-671
Ba002 Trailer brake lights 40-799 40-1331
fuse (key-on power) 40-877
(7.5A)
Ba003 Emergency fuse (di- 40-922 40-1331
rect) (20A)
Ba004 Seat compressor / 40-1105 40-1331
cigarette lighter fuse
(direct) (15A)
Ba005 Brake lights fuse 40-877 40-1331
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Ba006 Instrument panel 40-799 40-1331
fuse (direct) (5A) 40-1250
Ba007 Hydraulic reverse 40-799 40-1331
shuttle fuse (direct) 40-1250
(7.5A) 40-1158
Ba008 Low beam head- 40-922 40-1331
lights fuse (15A)
Ba009 High beam head- 40-922 40-1331
lights fuse (15A)
Ba010 Ancillary fuse (lift) [LNK] 40-1331
(15A)

40-170
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba011 Turn indicator lights 40-637 40-1331
fuse (key-on power) 40-1033
(15A) 40-984
40-922
40-877
40-755
40-750
40-671
40-665
Ba012 Socket fuse (key-on [LNK] 40-1331
power) (7.5A)
Ba013 Front loader fuse [LNK] 40-1331
(key-on power)
(7.5A)
Ba014 Fuse for work lights 40-984 40-1331
on cab (key-on pow- 40-1033
er) (15A)
Ba015 Fuse for low work 40-984 40-1331
lights (key-on power) 40-1033
(15A)
Ba016 Relay fuse (key-on 40-637 40-1331
power) (3A) 40-1237
40-1158
40-1033
40-984
40-922
40-877
40-799
40-755
40-750
40-671
40-665
Ba017 Instrument panel 40-600 40-1331
fuse (key-on power) 40-1250
(10A) 40-1158
40-922
40-877
40-799
40-723
40-701
Ba018 Engine ECU fuse 40-600 40-1331
(key-on power) 40-1250
(7.5A) 40-1158
40-799
40-701
Ba019 RH sidelights fuse 40-922 40-1331
(7.5A)
Ba020 LH sidelights fuse 40-922 40-1331
(7.5A)
Ba021 MK1 relay fuse 30A 40-799 40-1331
40-1158
40-1033
40-984
40-877
Ba022 Protection fuse, FT 40-750 40-1331
5-6-7-8 (30A) 40-1033
40-984
40-755

40-171
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Ba023 Fan/compressor 40-637 40-1331
fuse (30 A) 40-671
40-665
Ba024 Starter fuse (40A) 40-600 40-1331
40-1158
40-701
Ba025 Protection fuse 40-665 40-1331
(40A) 40-1105
40-1033
40-750
40-671
Ba026 MK3 relay fuse 30A 40-637 40-1331
40-1237
40-1033
40-984
40-922
40-877
40-755
40-671
40-665
Ba027 Distributor 7-8 fuse 40-1237 40-1331
(5A)
Ba028 Power socket fuse [LNK] 40-1331
(30A)
Ba029 Not used [LNK] 40-1331
Ba030 Steering column 40-922 40-1331
stalk fuse - lights in- 40-1105
put (20A)
Ba031 Ventilation/heating 40-637 40-1331
fuse (20A) 40-671
40-665

Table 127
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc001 Air conditioning com- 40-689 40-1365
pressor fuse (10A) 40-695
Bc002 Trailer brake lights 40-870 40-1365
fuse (key-on power) 40-902
(7.5A)
Bc003 Emergency fuse (di- 40-970 40-1365
rect) (20A)
Bc004 Seat compressor / 40-1125 40-1365
cigarette lighter fuse
(direct) (15A)
Bc005 Brake lights fuse 40-902 40-1365
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bc006 Instrument panel 40-870 40-1365
fuse (direct) (5A) 40-1266
40-902
Bc007 Hydraulic reverse 40-870 40-1365
shuttle fuse (direct) 40-1266
(7.5A) 40-1231
Bc008 Low beam head- 40-970 40-1365
lights fuse (15A)

40-172
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc009 High beam head- 40-970 40-1365
lights fuse (15A)
Bc010 Ancillary fuse (lift) 40-870 40-1365
(15A) 40-1266
40-1243
40-1269
40-1231
40-1067
40-1016
Bc011 Turn indicator lights 40-657 40-1365
fuse (key-on power) 40-1067
(15A) 40-1016
40-970
40-778
40-783
40-689
40-695
Bc012 Socket fuse (key-on [LNK] 40-1365
power) (7.5A)
Bc013 Front loader fuse [LNK] 40-1365
(key-on power)
(7.5A)
Bc014 Fuse for work lights 40-1016 40-1365
on cab (key-on pow- 40-1067
er) (15A)
Bc015 Fuse for low work [LNK] 40-1365
lights (key-on power)
(15A)
Bc016 Relay fuse (key-on 40-657 40-1365
power) (3A) 40-1067
40-1016
40-970
40-902
40-870
40-778
40-783
40-689
40-695
Bc017 Instrument panel 40-616 40-1365
fuse (key-on power) 40-1266
(10A) 40-1243
40-1269
40-1231
40-970
40-902
40-870
40-734
40-710
Bc018 Engine ECU fuse 40-616 40-1365
(key-on power) 40-1266
(7.5A) 40-1231
40-870
40-710
Bc019 RH sidelights fuse 40-970 40-1365
(7.5A)
Bc020 LH sidelights fuse 40-970 40-1365
(7.5A)

40-173
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc021 MK1 relay fuse 30A 40-870 40-1365
40-1067
40-1016
40-902
Bc022 Protection fuse, FT 40-778 40-1365
5-6-7-8 (30A) 40-1067
40-1016
40-783
Bc023 Fan/compressor 40-657 40-1365
fuse (30 A) 40-689
40-695
Bc024 Starter fuse (40A) 40-616 40-1365
40-1231
40-710
Bc025 Protection fuse 40-689 40-1365
(40A) 40-1125
40-1067
40-1016
40-695
Bc026 MK3 relay fuse 30A 40-657 40-1365
40-1067
40-1016
40-970
40-778
40-783
40-689
40-695
Bc027 Distributor 7-8 fuse [LNK] 40-1365
(5A)
Bc028 Power socket fuse [LNK] 40-1365
(30A)
Bc029 Not used [LNK] 40-1365
Bc030 Steering column 40-970 40-1365
stalk fuse - lights in- 40-1125
put (20A)
Bc031 Ventilation/heating 40-657 40-1365
fuse (20A) 40-689
40-695

40-174
Wiring diagrams
Table 128
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1033 40-1301
(10A - Rotating bea- 40-1067
con)
Be002 Fuse 2 in fuse box F 40-1105 40-1301
(5A - Radio) 40-1125
Be003 Fuse 3 in fuse box F 40-671 40-1301
(30A - Climate con- 40-695
trol)
Be005 Fuse 5 in fuse box F 40-750 40-1301
(7.5A - Windscreen 40-778
wiper)
Be006 Fuse 6 in fuse box F 40-750 40-1301
(7.5A - Rear screen 40-778
wiper)
Be007 Fuse 7 in fuse box 40-1033 40-1301
F (10A - Front work 40-1067
lights)
Be008 Fuse 8 in fuse box 40-1033 40-1301
F (10A - Rear work 40-1067
lights)
Bg001 10A fuse (beacon) 40-984 40-1388
40-1016
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-665 40-1388
and climate control) 40-689
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)
Bg007 10A fuse (rear work 40-984 40-1388
light) 40-1016
Bg008 10A fuse (front work 40-984 40-1388
lights) 40-1016

40-175
 Wiring diagrams
USA version

Bb026 Bb029

Bb022

Bb023
Bb021
Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1095 - Fuse box, cab version

l Bb001 - Air conditioning compressor fuse (10A)
l Bb002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bb003 - Emergency fuse (direct) (20A)
l Bb004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bb005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bb006 - Instrument panel fuse (direct) (5A)
l Bb007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bb008 - Cluster fuse +30 (3A)
l Bb009 - Wolp fuse +30 (10A)
l Bb010 - Ancillary fuse (lift) (15A)
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb012 - Socket fuse (key-on power) (7.5A)
l Bb013 - Front loader fuse (key-on power) (7.5A)
l Bb014 - Fuse for work lights on cab (key-on power) (15A)
l Bb015 - Fuse for low work lights (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb017 - Instrument panel fuse (key-on power) (10A)
l Bb018 - Engine ECU fuse (key-on power) (7.5A)
l Bb019 - RH sidelights fuse (7.5A)
l Bb020 - LH sidelights fuse (7.5A)
l Bb021 - MK1 relay fuse 30A
l Bb022- Protection fuse, FT 5-6-7-8 (30A)
l Bb023 - Fan/compressor fuse (30A)

40-176
Wiring diagrams

Bb026 Bb029

Bb022

Bb023
Bb021
Bb027 Bb030

Bb028 Bb031
Bb020

Bb019

Bb018

Bb017

Bb016

Bb015

Bb014

Bb013

Bb012

Bb011
Bb001

Bb002

Bb003

Bb004

Bb005

Bb006

Bb007

Bb008

Bb009

Bb010

Fig. 1095 - Fuse box, cab version

l Bb024 - Starter fuse (40A)
l Bb025 - Protection fuse (40A)
l Bb026 - MK3 relay fuse 30A
l Bb027 - Distributor 7-8 fuse (5A)
l Bb028 - Power socket fuse (30A)
l Bb029 - Not used
l Bb030 - Steering column stalk fuse - lights input (20A)
l Bb031 - Ventilation/heating fuse (20A)

40-177
 Wiring diagrams

Bc026 Bc029

Bc022

Bc023
Bc021
Bc027 Bc030

Bc028 Bc031
Bc020

Bc019

Bc018

Bc017

Bc016

Bc015

Bc014

Bc013

Bc012

Bc011
Bc001

Bc002

Bc003

Bc004

Bc005

Bc006

Bc007

Bc008

Bc009

Bc010

Fig. 1095 - Fuse box, cab version with electronic lift

l Bc001 - Air conditioning compressor fuse (10A)
l Bc002 - Trailer brake lights fuse (key-on power) (7.5A)
l Bc003 - Emergency fuse (direct) (20A)
l Bc004 - Seat compressor / cigarette lighter fuse (direct) (15A)
l Bc005 - Brake lights fuse (Europe version) - Trailer brake lights fuse (North America version) (direct) (15A)
l Bc006 - Instrument panel fuse (direct) (5A)
l Bc007 - Hydraulic reverse shuttle fuse (direct) (7.5A)
l Bc008 - Cluster fuse +30 (3A)
l Bc009 - Wolp fuse +30 (10A)
l Bc010 - Ancillary fuse (lift) (15A)
l Bc011 - Turn indicator lights fuse (key-on power) (15A)
l Bc012 - Socket fuse (key-on power) (7.5A)
l Bc013 - Front loader fuse (key-on power) (7.5A)
l Bc014 - Fuse for work lights on cab (key-on power) (15A)
l Bc015 - Fuse for low work lights (key-on power) (15A)
l Bc016 - Relay fuse (key-on power) (3A)
l Bc017 - Instrument panel fuse (key-on power) (10A)
l Bc018 - Engine ECU fuse (key-on power) (7.5A)
l Bc019 - RH sidelights fuse (7.5A)
l Bc020 - LH sidelights fuse (7.5A)
l Bc021 - MK1 relay fuse 30A
l Bc022 - Protection fuse, FT 5-6-7-8 (30A)
l Bc023 - Fan/compressor fuse (30A)
l Bc024 - Starter fuse (40A)
l Bc025 - Protection fuse (40A)

40-178
Wiring diagrams

Bc026 Bc029

Bc022

Bc023
Bc021
Bc027 Bc030

Bc028 Bc031
Bc020

Bc019

Bc018

Bc017

Bc016

Bc015

Bc014

Bc013

Bc012

Bc011
Bc001

Bc002

Bc003

Bc004

Bc005

Bc006

Bc007

Bc008

Bc009

Bc010

Fig. 1095 - Fuse box, cab version with electronic lift

l Bc026 - MK3 relay fuse 30A
l Bc027 - Distributor 7-8 fuse (5A)
l Bc028 - Power socket fuse (30A)
l Bc029 - Not used
l Bc030 - Steering column stalk fuse - lights input (20A)
l Bc031 - Ventilation/heating fuse (20A)

40-179
 Wiring diagrams
Table 129
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B001 0.900.0783.1 60A fuse 40-608 40-1295
40-1199
40-1266
40-1243
40-1269
40-1231
40-1067
40-1016
40-970
40-902
40-870
40-778
40-783
40-734
40-710
40-689
40-695
40-657
40-616
40-1240
40-1050
40-1001
40-935
40-895
40-882
40-764
40-769
40-728
40-705
40-683
40-677
40-647
40-1250
B002 Preheat fuse 125A 40-608 40-1290
40-710
40-616
40-705
B003 0.900.0783.1 60A fuse 40-647 40-1295
40-1067
40-1016
40-778
40-783
40-689
40-695
40-657
40-1115
40-1050
40-1001
40-764
40-769
40-683
40-677

40-180
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
B004 0.900.0783.1 60A fuse 40-647 40-1295
40-1199
40-1266
40-1243
40-1269
40-1231
40-1067
40-1016
40-970
40-902
40-870
40-778
40-783
40-689
40-695
40-657
40-1240
40-1115
40-1050
40-1001
40-935
40-895
40-882
40-834
40-764
40-769
40-683
40-677
Table 130
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb001 Air conditioning com- 40-683 40-1347
pressor fuse (10A) 40-677
Bb002 Trailer brake lights 40-882 40-1347
fuse (key-on power) 40-1199
(7.5A)
Bb003 Emergency fuse (di- 40-935 40-1347
rect) (20A)
Bb004 Seat compressor / 40-1115 40-1347
cigarette lighter fuse
(direct) (15A)
Bb005 Brake lights fuse 40-935 40-1347
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bb006 Instrument panel 40-1250 40-1347
fuse (direct) (5A) 40-834
Bb007 Hydraulic reverse 40-1250 40-1347
shuttle fuse (direct) 40-1199
(7.5A)
Bb008 Low beam head- 40-935 40-1347
lights fuse (15A)
Bb009 High beam head- 40-935 40-1347
lights fuse (15A)
Bb010 Ancillary fuse (lift) [LNK] 40-1347
(15A)

40-181
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb011 Turn indicator lights 40-647 40-1347
fuse (key-on power) 40-1050
(15A) 40-1001
40-935
40-882
40-764
40-769
40-683
40-677
Bb012 Socket fuse (key-on 40-935 40-1347
power) (7.5A)
Bb013 Front loader fuse [LNK] 40-1347
(key-on power)
(7.5A)
Bb014 Fuse for work lights 40-1001 40-1347
on cab (key-on pow- 40-1050
er) (15A)
Bb015 Fuse for low work 40-1001 40-1347
lights (key-on power) 40-1050
(15A)
Bb016 Relay fuse (key-on 40-647 40-1347
power) (3A) 40-1199
40-1240
40-1050
40-1001
40-935
40-882
40-834
40-764
40-769
40-683
40-677
Bb017 Instrument panel 40-1250 40-1347
fuse (key-on power) 40-1199
(10A) 40-935
40-882
40-834
40-728
40-705
40-608
Bb018 Engine ECU fuse 40-1250 40-1347
(key-on power) 40-1199
(7.5A) 40-705
40-608
Bb019 RH sidelights fuse 40-935 40-1347
(7.5A)
Bb020 LH sidelights fuse 40-935 40-1347
(7.5A)
Bb021 MK1 relay fuse 30A 40-834 40-1347
40-1199
40-1050
40-1001
40-882
Bb022 Protection fuse, FT 40-764 40-1347
5-6-7-8 (30A) 40-1050
40-1001
40-834
40-769

40-182
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bb023 Fan/compressor 40-647 40-1347
fuse (30 A) 40-683
40-677
Bb024 Starter fuse (40A) 40-608 40-1347
40-1199
40-705
Bb025 Protection fuse 40-683 40-1347
(40A) 40-1115
40-1050
40-1001
40-677
Bb026 MK3 relay fuse 30A 40-647 40-1347
40-1240
40-1050
40-1001
40-935
40-882
40-764
40-769
40-683
40-677
Bb027 Distributor 7-8 fuse 40-1240 40-1347
(5A)
Bb028 Power socket fuse [LNK] 40-1347
(30A)
Bb029 Not used [LNK] 40-1347
Bb030 Steering column 40-935 40-1347
stalk fuse - lights in- 40-1115
put (20A)
Bb031 Ventilation/heating 40-647 40-1347
fuse (20A) 40-683
40-677

40-183
 Wiring diagrams
Table 131
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc001 Air conditioning com- 40-689 40-1365
pressor fuse (10A) 40-695
Bc002 Trailer brake lights 40-870 40-1365
fuse (key-on power) 40-902
(7.5A)
Bc003 Emergency fuse (di- 40-970 40-1365
rect) (20A)
Bc004 Seat compressor / [LNK] 40-1365
cigarette lighter fuse
(direct) (15A)
Bc005 Brake lights fuse 40-902 40-1365
(Europe version) -
Trailer brake lights
fuse (North America
version) (direct)
(15A)
Bc006 Instrument panel 40-870 40-1365
fuse (direct) (5A) 40-1266
40-902
Bc007 Hydraulic reverse 40-870 40-1365
shuttle fuse (direct) 40-1266
(7.5A) 40-1231
Bc008 Low beam head- 40-970 40-1365
lights fuse (15A)
Bc009 High beam head- 40-970 40-1365
lights fuse (15A)
Bc010 Ancillary fuse (lift) 40-870 40-1365
(15A) 40-1266
40-1243
40-1269
40-1231
40-1067
40-1016
Bc011 Turn indicator lights 40-657 40-1365
fuse (key-on power) 40-1067
(15A) 40-1016
40-970
40-778
40-783
40-689
40-695
Bc012 Socket fuse (key-on [LNK] 40-1365
power) (7.5A)
Bc013 Front loader fuse [LNK] 40-1365
(key-on power)
(7.5A)
Bc014 Fuse for work lights 40-1016 40-1365
on cab (key-on pow- 40-1067
er) (15A)
Bc015 Fuse for low work [LNK] 40-1365
lights (key-on power)
(15A)

40-184
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc016 Relay fuse (key-on 40-657 40-1365
power) (3A) 40-1067
40-1016
40-970
40-902
40-870
40-778
40-783
40-689
40-695
Bc017 Instrument panel 40-616 40-1365
fuse (key-on power) 40-1266
(10A) 40-1243
40-1269
40-1231
40-970
40-902
40-870
40-734
40-710
Bc018 Engine ECU fuse 40-616 40-1365
(key-on power) 40-1266
(7.5A) 40-1231
40-870
40-710
Bc019 RH sidelights fuse [LNK] 40-1365
(7.5A)
Bc020 LH sidelights fuse 40-970 40-1365
(7.5A)
Bc021 MK1 relay fuse 30A 40-870 40-1365
40-1067
40-1016
40-902
Bc022 Protection fuse, FT 40-778 40-1365
5-6-7-8 (30A) 40-1067
40-1016
40-783
Bc023 Fan/compressor 40-657 40-1365
fuse (30 A) 40-689
40-695
Bc024 Starter fuse (40A) 40-616 40-1365
40-1231
40-710
Bc025 Protection fuse 40-689 40-1365
(40A) 40-1067
40-1016
40-695
Bc026 MK3 relay fuse 30A 40-657 40-1365
40-1067
40-1016
40-970
40-778
40-783
40-689
40-695
Bc027 Distributor 7-8 fuse [LNK] 40-1365
(5A)
Bc028 Power socket fuse [LNK] 40-1365
(30A)
Bc029 Not used [LNK] 40-1365

40-185
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Bc030 Steering column 40-970 40-1365
stalk fuse - lights in-
put (20A)
Bc031 Ventilation/heating 40-657 40-1365
fuse (20A) 40-689
40-695
Table 132
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Be001 Fuse 1 in fuse box F 40-1050 40-1301
(10A - Rotating bea- 40-1067
con)
Be002 Fuse 2 in fuse box F 40-1115 40-1301
(5A - Radio)
Be003 Fuse 3 in fuse box F 40-677 40-1301
(30A - Climate con- 40-695
trol)
Be005 Fuse 5 in fuse box F 40-764 40-1301
(7.5A - Windscreen 40-778
wiper)
Be006 Fuse 6 in fuse box F 40-764 40-1301
(7.5A - Rear screen 40-778
wiper)
Be007 Fuse 7 in fuse box 40-1050 40-1301
F (10A - Front work 40-1067
lights)
Be008 Fuse 8 in fuse box 40-1050 40-1301
F (10A - Rear work 40-1067
lights)
Bg001 10A fuse (beacon) 40-1001 40-1388
40-1016
Bg002 5A fuse (radio) [LNK] 40-1388
Bg003 20A fuse (heating 40-683 40-1388
and climate control) 40-689
Bg004 Not used [LNK] 40-1388
Bg005 7.5A fuse (wind- [LNK] 40-1388
screen wiper)
Bg006 7.5A fuse (rear [LNK] 40-1388
screen wiper)
Bg007 10A fuse (rear work 40-1001 40-1388
light) 40-1016
Bg008 10A fuse (front work 40-1001 40-1388
lights) 40-1016

40.2.13 - C - Grounds (AGROFARM 410 -> ZKDW350200TD25001)

ITA version
Table 133
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C003 Earthing point 40-641 40-1318
40-976
40-758

40-186
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C004 Earthing point 40-596 40-1330
40-1255
40-1247
40-1166
40-1145
40-1130
40-1099
40-1076
40-1024
40-976
40-942
40-915
40-889
40-877
40-807
40-791
40-758
40-750
40-738
40-723
40-671
40-701
40-714
40-641
40-637
40-621
C005 Earthing point 40-596 40-1330
40-1255
40-1247
40-1166
40-1145
40-1130
40-1099
40-1076
40-1024
40-976
40-942
40-915
40-889
40-877
40-807
40-791
40-758
40-750
40-738
40-723
40-714
40-701
40-671
40-641
40-637
40-621
C006 Earthing point 40-637 40-1388
40-976
40-665

40-187
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C007 Earthing point 40-596 40-1331
40-1247
40-1145
40-1099
40-1024
40-976
40-915
40-877
40-791
40-758
40-755
40-750
40-723
40-701
40-671
40-665
40-641
40-637
C008 Earthing point 40-596 40-1331
40-1145
40-1099
40-915
40-877
40-791
40-723
C009 Earthing point 40-596 40-1331
40-1247
40-1145
40-1099
40-915
40-877
40-791
40-758
40-755
40-750
40-723
40-701
C017 Earthing point 40-621 40-1392
40-1255
40-1166
40-1130
40-1076
40-942
40-889
40-807
40-738
40-714
C018 Earthing point 40-621 40-1392
40-1166
40-1130
40-1076
40-942
40-889
40-807
40-738

40-188
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C019 Grounding point 40-621 40-1392
40-1255
40-1166
40-1130
40-942
40-889
40-807
40-738
C023 Grounding point 40-671 40-1301
40-1099
40-1024
40-750

USA version
Table 134
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C003 Earthing point 40-772 40-1318
40-652
40-992
C004 Earthing point 40-604 40-1330
40-652
40-1255
40-1247
40-1206
40-1186
40-1137
40-1110
40-1087
40-1042
40-992
40-953
40-928
40-895
40-882
40-843
40-826
40-791
40-772
40-764
40-743
40-728
40-719
40-705
40-677
40-647
40-629

40-189
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C005 Earthing point 40-604 40-1330
40-652
40-1255
40-1247
40-1206
40-1186
40-1137
40-1110
40-1087
40-1042
40-992
40-953
40-928
40-895
40-882
40-843
40-826
40-791
40-772
40-764
40-743
40-728
40-719
40-705
40-677
40-647
40-629
C006 Earthing point 40-647 40-1388
40-992
40-683
C010 Battery earth 40-604 40-1347
40-652
40-1247
40-1186
40-1110
40-1042
40-992
40-928
40-882
40-826
40-772
40-769
40-764
40-728
40-705
40-677
40-683
40-647
C011 Battery earth 40-604 40-1347
40-1186
40-1110
40-928
40-882
40-826
40-728

40-190
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C012 Earthing point 40-604 40-1347
40-1247
40-1186
40-1110
40-928
40-882
40-826
40-772
40-769
40-764
40-728
40-705
C020 Grounding point 40-629 40-1410
40-1255
40-1206
40-1137
40-1087
40-953
40-895
40-843
40-743
40-719
C021 Grounding point 40-629 40-1410
40-1206
40-1137
40-1087
40-953
40-895
40-843
40-743
C022 Grounding point 40-629 40-1410
40-1255
40-1206
40-1137
40-953
40-895
40-843
40-743
40-719
C023 Grounding point 40-677 40-1301
40-1110
40-1042
40-764

40-191
 Wiring diagrams
40.2.14 - C - Grounds (AGROFARM 420 -> ZKDW390200TD25001)
ITA version
Table 135
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C003 Earthing point 40-641 40-1318
40-976
40-758
C004 Earthing point 40-596 40-1330
40-1255
40-1247
40-1166
40-1145
40-1130
40-1099
40-1076
40-1024
40-976
40-942
40-915
40-889
40-877
40-807
40-791
40-758
40-750
40-738
40-723
40-671
40-701
40-714
40-641
40-637
40-621
C005 Earthing point 40-596 40-1330
40-1255
40-1247
40-1166
40-1145
40-1130
40-1099
40-1076
40-1024
40-976
40-942
40-915
40-889
40-877
40-807
40-791
40-758
40-750
40-738
40-723
40-714
40-701
40-671
40-641
40-637
40-621

40-192
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C006 Earthing point 40-637 40-1388
40-976
40-665
C007 Earthing point 40-596 40-1331
40-1247
40-1237
40-1145
40-1099
40-1024
40-976
40-915
40-877
40-791
40-758
40-755
40-750
40-723
40-701
40-671
40-665
40-641
40-637
C008 Earthing point 40-596 40-1331
40-1237
40-1145
40-1099
40-915
40-877
40-791
40-723
C009 Earthing point 40-596 40-1331
40-1247
40-1145
40-1099
40-915
40-877
40-791
40-758
40-755
40-750
40-723
40-701
C017 Earthing point 40-621 40-1392
40-1255
40-1166
40-1130
40-1076
40-942
40-889
40-807
40-738
40-714
C018 Earthing point 40-621 40-1392
40-1166
40-1130
40-1076
40-942
40-889
40-807
40-738

40-193
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C019 Grounding point 40-621 40-1392
40-1255
40-1166
40-1130
40-942
40-889
40-807
40-738
C023 Grounding point 40-671 40-1301
40-1099
40-1024
40-750

USA version
Table 136
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C003 Earthing point 40-772 40-1318
40-652
40-992
C004 Earthing point 40-604 40-1330
40-652
40-1255
40-1247
40-1240
40-1206
40-1186
40-1137
40-1110
40-1087
40-1042
40-992
40-953
40-928
40-895
40-882
40-843
40-826
40-791
40-772
40-764
40-743
40-728
40-719
40-705
40-677
40-647
40-629

40-194
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C005 Earthing point 40-604 40-1330
40-652
40-1255
40-1247
40-1240
40-1206
40-1186
40-1137
40-1110
40-1087
40-1042
40-992
40-953
40-928
40-895
40-882
40-843
40-826
40-791
40-772
40-764
40-743
40-728
40-719
40-705
40-677
40-647
40-629
C006 Earthing point 40-647 40-1388
40-992
40-683
C010 Battery earth 40-604 40-1347
40-652
40-1247
40-1240
40-1186
40-1110
40-1042
40-992
40-928
40-882
40-826
40-772
40-769
40-764
40-728
40-705
40-677
40-683
40-647
C011 Battery earth 40-604 40-1347
40-1186
40-1110
40-928
40-882
40-826
40-728

40-195
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C012 Earthing point 40-604 40-1347
40-1247
40-1186
40-1110
40-928
40-882
40-826
40-772
40-769
40-764
40-728
40-705
C020 Grounding point 40-629 40-1410
40-1255
40-1206
40-1137
40-1087
40-953
40-895
40-843
40-743
40-719
C021 Grounding point 40-629 40-1410
40-1206
40-1137
40-1087
40-953
40-895
40-843
40-743
C022 Grounding point 40-629 40-1410
40-1255
40-1206
40-1137
40-953
40-895
40-843
40-743
40-719
C023 Grounding point 40-677 40-1301
40-1110
40-1042
40-764

40-196
Wiring diagrams
40.2.15 - C - Grounds (AGROFARM 430 -> ZKDW430200TD25001)
ITA version
Table 137
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C003 Earthing point 40-641 40-1318
40-660
40-976
40-758
C004 Earthing point 40-596 40-1330
40-1255
40-1166
40-1130
40-1076
40-953
40-889
40-807
40-738
40-714
40-621
40-1269
40-1262
40-1243
40-1226
40-1120
40-1059
40-1008
40-964
40-902
40-862
40-787
40-778
40-734
40-710
40-695
40-660
40-657
40-613
40-1247
40-1145
40-1099
40-1024
40-976
40-915
40-889
40-877
40-791
40-758
40-750
40-723
40-671
40-701
40-641
40-637

40-197
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C005 Earthing point 40-596 40-1330
40-1255
40-1166
40-1130
40-1076
40-953
40-889
40-807
40-738
40-714
40-621
40-1269
40-1262
40-1243
40-1226
40-1120
40-1059
40-1008
40-964
40-902
40-862
40-787
40-778
40-734
40-710
40-695
40-657
40-657
40-660
40-1247
40-1145
40-1099
40-1024
40-976
40-915
40-889
40-877
40-791
40-758
40-750
40-723
40-701
40-671
40-641
40-637
C006 Earthing point 40-637 40-1388
40-1008
40-689
40-657
40-976
40-665

40-198
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C007 Earthing point 40-596 40-1331
40-1247
40-1237
40-1145
40-1099
40-1024
40-976
40-915
40-877
40-791
40-758
40-755
40-750
40-723
40-701
40-671
40-665
40-641
40-637
C008 Earthing point 40-596 40-1331
40-1237
40-1145
40-1099
40-915
40-877
40-791
40-723
C009 Earthing point 40-596 40-1331
40-1247
40-1145
40-1099
40-915
40-877
40-791
40-758
40-755
40-750
40-723
40-701
C013 Earthing point 40-613 40-1365
40-1262
40-1226
40-1120
40-1059
40-1008
40-964
40-902
40-862
40-787
40-783
40-778
40-734
40-710
40-695
40-689

40-199
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C014 Grounding point 40-734 40-1365
40-1269
40-1262
40-1243
40-1226
40-1120
40-964
40-902
40-862
C015 Grounding point 40-613 40-1365
40-1262
40-1226
40-1120
40-964
40-902
40-862
40-787
40-783
40-778
40-734
40-710
C016 Earthing point 40-613 40-1385
40-1243
40-1226
40-902
40-862
40-734
C017 Earthing point 40-889 40-1392
40-1255
40-1166
40-1130
40-1076
40-953
40-889
40-807
40-738
40-714
40-621
C018 Earthing point 40-889 40-1392
40-1130
40-1166
40-1076
40-953
40-889
40-807
40-738
40-621
C019 Grounding point 40-889 40-1392
40-1255
40-807
40-1166
40-1130
40-953
40-889
40-738
40-621

40-200
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C023 Grounding point 40-671 40-1301
40-1120
40-1059
40-778
40-695
40-1099
40-1024
40-750

USA version
Table 138
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C003 Earthing point 40-772 40-1318
40-652
40-660
40-992

40-201
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C004 Earthing point 40-604 40-1330
40-1255
40-1206
40-1137
40-1087
40-964
40-895
40-826
40-743
40-719
40-629
40-652
40-1269
40-1262
40-1243
40-1226
40-1120
40-1059
40-1008
40-964
40-902
40-862
40-787
40-778
40-734
40-710
40-695
40-660
40-657
40-1247
40-1240
40-1186
40-1110
40-1042
40-992
40-928
40-895
40-882
40-826
40-791
40-772
40-764
40-728
40-705
40-677
40-647

40-202
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C005 Earthing point 40-604 40-1330
40-1255
40-1206
40-1137
40-964
40-1087
40-895
40-743
40-826
40-719
40-629
40-652
40-1269
40-1262
40-1243
40-1226
40-1120
40-1059
40-1008
40-964
40-902
40-862
40-787
40-778
40-734
40-710
40-695
40-660
40-657
40-1247
40-1240
40-1186
40-1110
40-1042
40-992
40-928
40-895
40-882
40-826
40-791
40-772
40-764
40-728
40-705
40-677
40-647
C006 Earthing point 40-647 40-1388
40-1008
40-695
40-657
40-992
40-683

40-203
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C010 Battery earth 40-604 40-1347
40-826
40-652
40-1247
40-1240
40-1186
40-1110
40-1042
40-992
40-928
40-882
40-826
40-772
40-769
40-764
40-728
40-705
40-677
40-683
40-647
C011 Battery earth 40-604 40-1347
40-826
40-1186
40-1110
40-928
40-882
40-826
40-728
C012 Earthing point 40-604 40-1347
40-826
40-1247
40-1186
40-1110
40-928
40-882
40-826
40-772
40-769
40-764
40-728
40-705
C013 Earthing point 40-695 40-1365
40-1262
40-1226
40-1120
40-1059
40-1008
40-964
40-902
40-862
40-787
40-783
40-778
40-734
40-710
40-695
40-689

40-204
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C014 Grounding point 40-734 40-1365
40-1269
40-1262
40-1243
40-1226
40-1120
40-964
40-902
40-862
C015 Grounding point 40-710 40-1365
40-1262
40-1226
40-1120
40-964
40-902
40-862
40-787
40-783
40-734
40-613
C016 Earthing point 40-734 40-1385
40-1243
40-1226
40-902
40-862
C020 Grounding point 40-895 40-1410
40-1255
40-1137
40-1206
40-1087
40-964
40-895
40-743
40-719
40-629
C021 Grounding point 40-895 40-1410
40-1206
40-1137
40-1087
40-964
40-895
40-743
40-629
C022 Grounding point 40-895 40-1410
40-1255
40-1206
40-964
40-1137
40-895
40-743
40-719
40-629
C023 Grounding point 40-677 40-1301
40-1120
40-1059
40-778
40-695
40-1110
40-1042
40-764

40-205
 Wiring diagrams
40.2.16 - C - Grounds (AGROFARM 410 -> ZKDW470200TD30001)
ITA version
Table 139
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C004 Earthing point 40-600 40-1330
40-1258
40-1250
40-1178
40-1158
40-1133
40-1105
40-1082
40-1033
40-984
40-948
40-922
40-889
40-877
40-816
40-799
40-750
40-738
40-723
40-671
40-701
40-714
40-637
40-625
C005 Earthing point 40-600 40-1330
40-1258
40-1250
40-1178
40-1158
40-1133
40-1105
40-1082
40-1033
40-984
40-948
40-922
40-889
40-877
40-816
40-799
40-750
40-738
40-723
40-714
40-701
40-671
40-637
40-625
C006 Earthing point 40-637 40-1388
40-984
40-665

40-206
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C007 Earthing point 40-600 40-1331
40-1250
40-1237
40-1158
40-1105
40-1033
40-984
40-922
40-877
40-799
40-755
40-750
40-723
40-701
40-671
40-665
40-637
C008 Earthing point 40-600 40-1331
40-1237
40-1158
40-1105
40-922
40-877
40-799
40-723
C009 Earthing point 40-600 40-1331
40-1250
40-1158
40-1105
40-922
40-877
40-799
40-755
40-750
40-723
40-701
C010 Battery earth 40-1250 40-1347
C011 Battery earth [LNK] 40-1347
C012 Earthing point 40-1250 40-1347
C017 Earthing point 40-625 40-1392
40-1258
40-1178
40-1133
40-1082
40-948
40-889
40-816
40-738
40-714
C018 Earthing point 40-625 40-1392
40-1178
40-1133
40-1082
40-948
40-889
40-816
40-738

40-207
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C019 Grounding point 40-625 40-1392
40-1258
40-1178
40-1133
40-948
40-889
40-816
40-738
C020 Grounding point 40-1258 40-1410
C021 Grounding point [LNK] 40-1410
C022 Grounding point 40-1258 40-1410
C023 Grounding point 40-671 40-1301
40-1105
40-1033
40-750
USA version
Table 140
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C004 Earthing point 40-608 40-1330
40-1258
40-1250
40-1240
40-1218
40-1199
40-1141
40-1115
40-1093
40-1050
40-1001
40-959
40-935
40-895
40-882
40-852
40-834
40-799
40-764
40-743
40-728
40-719
40-705
40-677
40-647
40-633

40-208
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C005 Earthing point 40-608 40-1330
40-1258
40-1250
40-1240
40-1218
40-1199
40-1141
40-1115
40-1093
40-1050
40-1001
40-959
40-935
40-895
40-882
40-852
40-834
40-799
40-764
40-743
40-728
40-719
40-705
40-677
40-647
40-633
C006 Earthing point 40-647 40-1388
40-1001
40-683
C007 Earthing point 40-799 40-1331
40-1250
C008 Earthing point 40-799 40-1331
C009 Earthing point 40-799 40-1331
40-1250
C010 Battery earth 40-608 40-1347
40-1250
40-1240
40-1199
40-1115
40-1050
40-1001
40-935
40-882
40-834
40-769
40-764
40-728
40-705
40-677
40-683
40-647
C011 Battery earth 40-608 40-1347
40-1199
40-1115
40-935
40-882
40-834
40-728

40-209
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C012 Earthing point 40-608 40-1347
40-1250
40-1199
40-1115
40-935
40-882
40-834
40-769
40-764
40-728
40-705
C017 Earthing point 40-1258 40-1392
C018 Earthing point [LNK] 40-1392
C019 Grounding point 40-1258 40-1392
C020 Grounding point 40-633 40-1410
40-1258
40-1218
40-1141
40-1093
40-959
40-895
40-852
40-743
40-719
C021 Grounding point 40-633 40-1410
40-1218
40-1141
40-1093
40-959
40-895
40-852
40-743
C022 Grounding point 40-633 40-1410
40-1258
40-1218
40-1141
40-959
40-895
40-852
40-743
40-719
C023 Grounding point 40-677 40-1301
40-1115
40-1050
40-764

40-210
Wiring diagrams
40.2.17 - C - Grounds (AGROFARM 420 -> ZKDW510200TD30001)
ITA version
Table 141
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C004 Earthing point 40-600 40-1330
40-1258
40-1250
40-1178
40-1158
40-1133
40-1105
40-1082
40-1033
40-984
40-948
40-922
40-889
40-877
40-816
40-799
40-750
40-738
40-723
40-671
40-701
40-714
40-637
40-625
C005 Earthing point 40-600 40-1330
40-1258
40-1250
40-1178
40-1158
40-1133
40-1105
40-1082
40-1033
40-984
40-948
40-922
40-889
40-877
40-816
40-799
40-750
40-738
40-723
40-714
40-701
40-671
40-637
40-625
C006 Earthing point 40-637 40-1388
40-984
40-665

40-211
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C007 Earthing point 40-600 40-1331
40-1250
40-1237
40-1158
40-1105
40-1033
40-984
40-922
40-877
40-799
40-755
40-750
40-723
40-701
40-671
40-665
40-637
C008 Earthing point 40-600 40-1331
40-1237
40-1158
40-1105
40-922
40-877
40-799
40-723
C009 Earthing point 40-600 40-1331
40-1250
40-1158
40-1105
40-922
40-877
40-799
40-755
40-750
40-723
40-701
C010 Battery earth 40-1250 40-1347
C011 Battery earth [LNK] 40-1347
C012 Earthing point 40-1250 40-1347
C017 Earthing point 40-625 40-1392
40-1258
40-1178
40-1133
40-1082
40-948
40-889
40-816
40-738
40-714
C018 Earthing point 40-625 40-1392
40-1178
40-1133
40-1082
40-948
40-889
40-816
40-738

40-212
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C019 Grounding point 40-625 40-1392
40-1258
40-1178
40-1133
40-948
40-889
40-816
40-738
C020 Grounding point 40-1258 40-1410
C021 Grounding point [LNK] 40-1410
C022 Grounding point 40-1258 40-1410
C023 Grounding point 40-671 40-1301
40-1105
40-1033
40-750
USA version
Table 142
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C004 Earthing point 40-608 40-1330
40-1258
40-1250
40-1240
40-1218
40-1199
40-1141
40-1115
40-1093
40-1050
40-1001
40-959
40-935
40-895
40-882
40-852
40-834
40-799
40-764
40-743
40-728
40-719
40-705
40-677
40-647
40-633

40-213
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C005 Earthing point 40-608 40-1330
40-1258
40-1250
40-1240
40-1218
40-1199
40-1141
40-1115
40-1093
40-1050
40-1001
40-959
40-935
40-895
40-882
40-852
40-834
40-799
40-764
40-743
40-728
40-719
40-705
40-677
40-647
40-633
C006 Earthing point 40-647 40-1388
40-1001
40-683
C007 Earthing point 40-799 40-1331
40-1250
C008 Earthing point 40-799 40-1331
C009 Earthing point 40-799 40-1331
40-1250
C010 Battery earth 40-608 40-1347
40-1250
40-1240
40-1199
40-1115
40-1050
40-1001
40-935
40-882
40-834
40-769
40-764
40-728
40-705
40-677
40-683
40-647
C011 Battery earth 40-608 40-1347
40-1199
40-1115
40-935
40-882
40-834
40-728

40-214
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C012 Earthing point 40-608 40-1347
40-1250
40-1199
40-1115
40-935
40-882
40-834
40-769
40-764
40-728
40-705
C017 Earthing point 40-1258 40-1392
C018 Earthing point [LNK] 40-1392
C019 Grounding point 40-1258 40-1392
C020 Grounding point 40-633 40-1410
40-1258
40-1218
40-1141
40-1093
40-959
40-895
40-852
40-743
40-719
C021 Grounding point 40-633 40-1410
40-1218
40-1141
40-1093
40-959
40-895
40-852
40-743
C022 Grounding point 40-633 40-1410
40-1258
40-1218
40-1141
40-959
40-895
40-852
40-743
40-719
C023 Grounding point 40-677 40-1301
40-1115
40-1050
40-764

40-215
 Wiring diagrams
40.2.18 - C - Grounds (AGROFARM 430 -> ZKDW550200TD30001)
ITA version
Table 143
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C004 Earthing point 40-600 40-1330
40-1269
40-1266
40-1243
40-1231
40-1125
40-1067
40-1016
40-970
40-902
40-870
40-778
40-734
40-710
40-695
40-657
40-616
40-1250
40-1158
40-1105
40-1033
40-984
40-922
40-889
40-877
40-799
40-750
40-723
40-671
40-701
40-637

40-216
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C005 Earthing point 40-600 40-1330
40-1269
40-1266
40-1243
40-1231
40-1125
40-1067
40-1016
40-970
40-902
40-870
40-778
40-734
40-710
40-695
40-657
40-657
40-1250
40-1158
40-1105
40-1033
40-984
40-922
40-889
40-877
40-799
40-750
40-723
40-701
40-671
40-637
C006 Earthing point 40-637 40-1388
40-1016
40-689
40-657
40-984
40-665
C007 Earthing point 40-600 40-1331
40-1250
40-1237
40-1158
40-1105
40-1033
40-984
40-922
40-877
40-799
40-755
40-750
40-723
40-701
40-671
40-665
40-637
C008 Earthing point 40-600 40-1331
40-1237
40-1158
40-1105
40-922
40-877
40-799
40-723

40-217
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C009 Earthing point 40-600 40-1331
40-1250
40-1158
40-1105
40-922
40-877
40-799
40-755
40-750
40-723
40-701
C013 Earthing point 40-616 40-1365
40-1266
40-1231
40-1125
40-1067
40-1016
40-970
40-902
40-870
40-783
40-778
40-734
40-710
40-695
40-689
C014 Grounding point 40-734 40-1365
40-1269
40-1266
40-1243
40-1231
40-1125
40-970
40-902
40-870
C015 Grounding point 40-616 40-1365
40-1266
40-1231
40-1125
40-970
40-902
40-870
40-783
40-778
40-734
40-710
C016 Earthing point 40-616 40-1385
40-1243
40-1231
40-902
40-870
40-734
C023 Grounding point 40-671 40-1301
40-1125
40-1067
40-778
40-695
40-1105
40-1033
40-750

40-218
Wiring diagrams
USA version
Table 144
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C001 Earthing point [LNK] 40-1329
C002 Earthing point [LNK] 40-1329
C004 Earthing point 40-608 40-1330
40-1269
40-1266
40-1243
40-1231
40-1125
40-1067
40-1016
40-970
40-902
40-870
40-778
40-734
40-710
40-695
40-657
40-1250
40-1240
40-1199
40-1115
40-1050
40-1001
40-935
40-895
40-882
40-834
40-799
40-764
40-728
40-705
40-677
40-647

40-219
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C005 Earthing point 40-608 40-1330
40-1269
40-1266
40-1243
40-1231
40-1125
40-1067
40-1016
40-970
40-902
40-870
40-778
40-734
40-710
40-695
40-657
40-1250
40-1240
40-1199
40-1115
40-1050
40-1001
40-935
40-895
40-882
40-834
40-799
40-764
40-728
40-705
40-677
40-647
C006 Earthing point 40-647 40-1388
40-1016
40-695
40-657
40-1001
40-683
C010 Battery earth 40-608 40-1347
40-1250
40-1240
40-1199
40-1115
40-1050
40-1001
40-935
40-882
40-834
40-769
40-764
40-728
40-705
40-677
40-683
40-647
C011 Battery earth 40-608 40-1347
40-1199
40-1115
40-935
40-882
40-834
40-728

40-220
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
C012 Earthing point 40-608 40-1347
40-1250
40-1199
40-1115
40-935
40-882
40-834
40-769
40-764
40-728
40-705
C013 Earthing point 40-695 40-1365
40-1266
40-1231
40-1125
40-1067
40-1016
40-970
40-902
40-870
40-783
40-778
40-734
40-710
40-695
40-689
C014 Grounding point 40-734 40-1365
40-1269
40-1266
40-1243
40-1231
40-1125
40-970
40-902
40-870
C015 Grounding point 40-710 40-1365
40-1266
40-1231
40-1125
40-970
40-902
40-870
40-783
40-734
40-616
C016 Earthing point 40-734 40-1385
40-1243
40-1231
40-902
40-870
C023 Grounding point 40-677 40-1301
40-1125
40-1067
40-778
40-695
40-1115
40-1050
40-764

40-221
 Wiring diagrams
40.2.19 - D - Intermediate connections (AGROFARM 410 -> ZKDW350200TD25001)
ITA version
Table 145
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D001 Wiring connector 40-723 40-1331
40-1145
40-791
D001 Wiring connector for 40-723 40-1331
switch wiring loom 40-1145
40-791
D002 Wiring connector for 40-1099 40-1331
seat wiring loom
D002 Wiring connector for 40-1099 40-1279
central wiring loom
D003 Wiring connector for 40-791 40-1331
parking brake wiring 40-877
loom
D003 Wiring connector 40-791 40-1331
40-877
D003 Wiring connector for [LNK] [LNK]
parking brake wiring
loom
D004 Wiring connector for 40-596 40-1306
central wiring loom 40-1237
40-1166
40-1145
40-1076
40-942
40-915
40-877
40-889
40-807
40-807
40-701
40-714
40-723
40-738
40-791
40-621
D004 Wiring connector for 40-596 40-1331
rear wiring loom 40-723
40-791
40-877
40-915
40-1145
40-1237
40-701
D004 Wiring connector for 40-621 40-1392
rear wiring loom 40-889
40-942
40-1076
40-1166
40-807
40-714
40-738
D005 Wiring connector for 40-1237 40-1331
auxiliary distributor
control wiring loom

40-222
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D006 Wiring connector for 40-596 40-1331
reverse shuttle wir- 40-791
ing loom 40-1145
40-1247
D006 Wiring connector for 40-621 40-1392
reverse shuttle wir- 40-807
ing loom 40-1166
40-1255
D008 Seat configuration 40-791 40-1331
connector
D008a Seat configuration 40-791 40-1331
connector
D008b Seat configuration 40-791 40-1331
connector
D009 Wiring connector for 40-915 40-1312
central wiring loom 40-1024
40-976
D009 Wiring connector for 40-915 40-1331
front lights wiring 40-976
loom 40-1024
D010 Wiring connector for 40-596 40-1331
engine wiring loom 40-665
40-671
40-701
40-723
D010 Wiring connector for 40-621 40-1392
engine wiring loom 40-714
40-738
40-807
D010 Wiring connector for 40-596 40-1324
central wiring loom 40-723
40-738
40-807
40-701
40-714
40-665
40-671
40-621
D011 Wiring connector for 40-915 40-1309
central wiring loom 40-1130
40-1099
40-942
D011 Wiring connector for 40-915 40-1331
cowl lights wiring 40-976
loom 40-1024
40-1099
D011 Wiring connector for 40-942 40-1392
cowl lights wiring 40-1076
loom 40-1130
D012 Wiring connector for 40-637 40-1311
roof wiring loom 40-665
40-671
D012 Wiring connector for 40-671 40-1301
cab power wiring
loom
D012 Wiring connector for 40-641 40-1318
cab power wiring
loom

40-223
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D012 Wiring connector for 40-637 40-1388
cab power wiring 40-665
loom
D013 Wiring connector for 40-637 40-1331
power wiring loom 40-755
40-758
40-976
40-1024
40-1099
40-641
40-665
40-671
40-750
D013 Wiring connector for [LNK] 40-1392
power wiring loom
D013 Wiring connector for 40-637 40-1295
central wiring loom 40-1099
40-1024
40-976
40-807
40-641
40-758
40-755
40-750
40-671
40-665
D014 Wiring connector for 40-701 40-1306
engine wiring loom 40-807
40-714

Table 146
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D015 Wiring connector for 40-807 40-1306
trailer air brake wir- 40-877
ing loom 40-889
D015 Wiring connector for 40-877 40-1287
rear wiring loom 40-889
D017 Wiring connector for 40-807 40-1306
auxiliary distributor 40-1237
solenoid valves
D018 Wiring connector for 40-807 40-1306
PTO sensor wiring
loom - (USA EX-
PORT)
D019 Wiring connector for 40-1076 40-1306
work light and rotat- 40-807
ing beacon wiring
loom
D019 Wiring connector for [LNK] 40-1292
rear wiring loom
D025 Wiring connector for 40-641 40-1318
heating wiring loom
D025 Wiring connector for 40-637 40-1388
air conditioner wiring 40-665
loom
D025 Wiring connector for [LNK] 40-1274
roof wiring loom

40-224
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D025 Wiring connector for [LNK] 40-1275
roof wiring loom
D026 Wiring connector for 40-665 40-1388
air conditioner wiring
loom
D026 Wiring connector for [LNK] 40-1275
roof wiring loom
D027 Wiring connector for 40-915 40-1312
RH lower front head- 40-1024
light 40-976
D027 Wiring connector for 40-915 40-1427
low front lights wiring 40-976
loom 40-1024
D028 Wiring connector for 40-671 40-1301
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1388
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1308
roof wiring loom 40-671
D029 Connection between 40-671 40-1301
cab power supply 40-1099
wiring and HV roof 40-750
40-1024
wiring
D029 Wiring connector for 40-671 40-1301
cab power wiring 40-1099
loom 40-750
40-1024
D029 Wiring connector for 40-758 40-1318
cab power wiring 40-976
loom
D029 Wiring connector for 40-665 40-1388
cab power wiring 40-976
loom
D029 Wiring connector for 40-665 40-1311
roof wiring loom 40-1024
40-1099
40-758
40-976
40-671
40-750
40-755
D030 Wiring connector for 40-665 40-1311
central cab wiring 40-1024
loom 40-1099
40-758
40-976
40-671
40-750
40-755

40-225
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D030 Wiring connector for 40-665 40-1331
cab power wiring 40-976
loom 40-1024
40-1099
40-671
40-750
40-755
40-758
D030 Wiring connector for [LNK] 40-1392
cab power wiring
loom
D031 Wiring connector for 40-637 40-1331
cab power wiring 40-641
loom 40-665
40-671
D031 Wiring connector for 40-637 40-1311
central wiring loom 40-665
40-671
40-641
Table 147
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D032 Wiring connector for 40-671 40-1301
cab power wiring
loom
D032 Wiring connector for 40-637 40-1311
roof wiring loom 40-665
40-671
40-641
D033 Wiring connector for 40-671 40-1301
roof
D033 Wiring connector to 40-671 40-1301
wiring loom
D034 Wiring connector for 40-671 40-1301
roof
D034 Wiring connector to 40-671 40-1301
wiring loom
D035 Wiring connector for 40-807 40-1327
central wiring loom
and electronic lift
D036 Wiring connector 40-714 40-1392
40-1076
40-1166
40-807
40-738
D036 Wiring connector for 40-714 40-1392
switch wiring loom 40-1076
40-1166
40-807
40-738

40-226
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D039 Wiring connector for 40-637 40-1295
central cab wiring 40-1237
loom 40-1166
40-1130
40-1145
40-1076
40-942
40-889
40-915
40-877
40-791
40-1099
40-1024
40-976
40-807
40-641
40-758
40-755
40-750
40-671
40-665
D039 Wiring connector for 40-637 40-1331
power wiring loom 40-1145
40-1237
40-758
40-791
40-877
40-915
40-976
40-1024
40-1099
40-641
40-665
40-671
40-750
40-755
D039 Wiring connector for 40-807 40-1392
power wiring loom 40-1166
40-942
40-1076
40-1130
40-889
D040 Wiring connector for 40-621 40-1392
power wiring loom 40-942
40-1076
40-1166
40-1255
40-714
40-738
40-807
40-889

40-227
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D040 Wiring connector for 40-596 40-1331
power wiring loom 40-1024
40-1145
40-1237
40-1247
40-791
40-877
40-915
40-976
40-723
40-750
40-755
40-758
40-701
40-637
40-641
40-665
40-671
D040 Wiring connector for 40-596 40-1295
central wiring loom 40-1255
40-1247
40-1237
40-1166
40-1145
40-1076
40-1024
40-976
40-758
40-791
40-807
40-877
40-889
40-915
40-942
40-637
40-641
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-621
D044 Wiring connector for 40-750 40-1301
windscreen wiper
motor wiring loom
D044 Wiring connector for 40-750 40-1279
roof wiring loom
D045 Wiring connector for 40-758 40-1318
windscreen wiper
wiring loom
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D045 Wiring connector for [LNK] 40-1276
[LNK]

40-228
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D046 Wiring connector for 40-758 40-1318
work lights and wind- 40-976
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector for 40-976 40-1388
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector to 40-755 40-1322
cab roof wiring loom, 40-976
versions with stan- 40-758
dard cab

Table 148
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-755 40-1322
rear screen wiper 40-758
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for 40-758 40-1300
work lights and wind- 40-755
screen wiper wiring
loom, versions with-
out high visibility cab
D048 Wiring connector 40-807 40-1392
40-889
D048 Wiring connector for 40-807 40-1392
parking brake wiring 40-889
loom
D049 Seat configuration 40-807 40-1392
connector
D049a Seat configuration 40-807 40-1392
connector
D049b Seat configuration 40-807 40-1392
connector
D050 Wiring connector for 40-915 40-1312
RH lower front head- 40-1024
light 40-976
D050 Wiring connector for 40-915 40-1427
low front lights wiring 40-976
loom 40-1024
D051 Wiring connector for 40-1024 40-1288
LH lower headlight
wiring loom
D051 2.8059.528.0 Wiring connector for 40-915 40-1427
front lower work light 40-976
wiring loom, ver- 40-1024
sions with high vis-
ibility cab
D052 Wiring connector for 40-915 40-1427
low front lights wiring 40-976
loom 40-1024

40-229
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D052 Wiring connector for 40-915 40-1312
LH lower front head- 40-1024
light 40-976
D053 2.8059.528.0 Wiring connector for 40-915 40-1427
front lower work light 40-976
wiring loom, ver- 40-1024
sions with high vis-
ibility cab
D053 Wiring connector for 40-1024 40-1288
RH lower headlight
wiring loom

Table 149
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D060 Wiring connector for 40-877 40-1331
rear RH work light 40-915
wiring loom
D060 Wiring connector for 40-889 40-1392
rear RH work light 40-942
wiring loom
D061 Wiring connector for 40-877 40-1331
rear LH work light 40-915
wiring loom
D061 Wiring connector for 40-889 40-1392
rear LH work light 40-942
wiring loom
D062 Wiring connector for 40-915 40-1427
low front lights wiring 40-976
loom 40-1024
D062 Wiring connector for 40-915 40-1312
LH lower front head- 40-1024
light 40-976
D063 Wiring connector for 40-1024 40-1301
flashing beacon wir-
ing loom
D063 Wiring connector for 40-976 40-1322
flashing beacon wir-
ing loom
D063 Wiring connector for 40-976 40-1286
roof wiring loom 40-1024
D064 Wiring connector for 40-1024 40-1301
flashing beacon wir-
ing loom
D064 Wiring connector for 40-976 40-1322
flashing beacon wir-
ing loom
D064 Wiring connector for 40-976 40-1286
roof wiring loom 40-1024
D067 Wiring connector for [LNK] 40-1392
windscreen washer
pump wiring loom
D068 Wiring connector for [LNK] 40-1392
roof wiring loom

40-230
Wiring diagrams
Table 150
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D072 Wiring connector for [LNK] 40-1392
windscreen washer
pump wiring loom
D075 Wiring connector for 40-1024 40-1424
roof wiring loom
D075 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
RH front work light
D076 Wiring connector for 40-1024 40-1424
roof wiring loom
D076 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
LH front work light
D077 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
LH rear work light
D078 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
RH rear work light
D079 Wiring connector for 40-791 40-1331
HL lever wiring loom 40-1145
D079 Wiring connector for 40-807 40-1392
central wiring loom 40-1166
D080 Wiring connector for [LNK] 40-1318
air conditioner
D081 Wiring connector for [LNK] 40-1318
condenser wiring
loom
D082 Wiring connector for 40-807 40-1327
front PTO control so- 40-723
lenoid valve 40-738
D082 Wiring connector for 40-723 40-1324
front PTO control so- 40-738
lenoid valve 40-807
D082 Wiring connector for 40-723 40-1281
engine wiring loom 40-738
D083 Wiring connector for 40-942 40-1317
central wiring loom
D083 Wiring connector for 40-942 40-1392
front lights wiring 40-1076
loom
D086 Wiring connector for [LNK] 40-1285
central wiring loom
D087 Wiring connector for [LNK] 40-1285
central wiring loom
F004 04411920.4 Front LH sidelight 40-915 40-1427
and turn indicator
USA version
Table 151
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D002 Wiring connector for [LNK] 40-1279
central wiring loom

40-231
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D004 Wiring connector for 40-604 40-1306
central wiring loom 40-928
40-953
40-1087
40-1186
40-1206
40-1240
40-843
40-882
40-895
40-743
40-826
40-719
40-728
40-629
40-705
D004 Wiring connector for 40-604 40-1347
rear wiring loom 40-1240
40-1186
40-882
40-928
40-705
40-728
40-826
D004 Wiring connector for 40-629 40-1410
rear wiring loom 40-895
40-953
40-1087
40-1206
40-719
40-743
40-843
D005 Wiring connector for 40-1240 40-1347
auxiliary distributor
control wiring loom
D006 Wiring connector for 40-604 40-1347
reverse shuttle wir- 40-1247
ing loom 40-826
40-1186
40-1206
D006 Wiring connector for 40-629 40-1410
reverse shuttle wir- 40-843
ing loom 40-1206
D009 Wiring connector for 40-928 40-1312
central wiring loom 40-992
40-1042
D009 Wiring connector for 40-928 40-1347
front lights wiring 40-1042
loom 40-992
D010 Wiring connector for 40-629 40-1410
engine wiring loom 40-719
40-743
40-843
D010 Wiring connector for 40-604 40-1347
front wiring loom 40-728
40-826
40-683
40-677
40-705

40-232
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D010 Wiring connector for 40-604 40-1324
central wiring loom 40-743
40-843
40-719
40-728
40-705
40-629
40-683
40-677
D011 Wiring connector for 40-928 40-1309
central wiring loom 40-1110
40-1137
40-953
D011 Wiring connector for 40-928 40-1347
cowl lights wiring 40-992
loom 40-1042
40-1110
D011 Wiring connector for 40-953 40-1410
cowl lights wiring 40-1087
loom 40-1137
D012 Wiring connector for 40-647 40-1311
roof wiring loom 40-683
40-677
40-652
D012 Wiring connector for 40-677 40-1301
cab power wiring
loom
D012 Wiring connector for 40-652 40-1318
cab power wiring
loom
D012 Wiring connector for 40-647 40-1388
cab power wiring 40-683
loom
D013 Wiring connector for 40-647 40-1347
power wiring loom 40-1110
40-772
40-992
40-1042
40-683
40-677
40-764
40-769
D013 Wiring connector for [LNK] 40-1410
power wiring loom
D013 Wiring connector for 40-647 40-1295
central wiring loom 40-1110
40-843
40-992
40-1042
40-764
40-769
40-772
40-826
40-652
40-683
40-677
D014 Wiring connector for 40-705 40-1306
engine wiring loom 40-719
40-843
40-882

40-233
 Wiring diagrams
Table 152
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D015 Wiring connector for 40-843 40-1306
trailer air brake wir- 40-882
ing loom 40-895
D017 Wiring connector for 40-843 40-1306
auxiliary distributor 40-1240
solenoid valves
D018 Wiring connector for 40-728 40-1300
central wiring loom 40-743
D018 Wiring connector for 40-728 40-1306
PTO sensor wiring 40-843
loom - (USA EX- 40-743
PORT)
D019 Wiring connector for 40-843 40-1306
work light and rotat- 40-1087
ing beacon wiring
loom
D019 Wiring connector for 40-1087 40-1292
rear wiring loom
D025 Wiring connector for 40-652 40-1318
heating wiring loom
D025 Wiring connector for 40-647 40-1388
air conditioner wiring 40-683
loom
D025 Wiring connector for 40-647 40-1274
roof wiring loom 40-652
D025 Wiring connector for 40-683 40-1275
roof wiring loom
D026 Wiring connector for 40-683 40-1388
air conditioner wiring
loom
D026 Wiring connector for 40-683 40-1275
roof wiring loom
D027 Wiring connector for 40-928 40-1312
RH lower front head- 40-992
light 40-1042
D027 Wiring connector for 40-928 40-1427
low front lights wiring 40-992
loom 40-1042
D028 Wiring connector for 40-677 40-1301
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1388
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1308
roof wiring loom 40-677
D029 Connection between 40-677 40-1301
cab power supply 40-1042
wiring and HV roof 40-1110
40-764
wiring

40-234
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D029 Wiring connector for 40-677 40-1301
cab power wiring 40-1042
loom 40-1110
40-764
D029 Wiring connector for 40-772 40-1318
cab power wiring 40-992
loom
D029 Wiring connector for 40-683 40-1388
cab power wiring 40-992
loom
D029 Wiring connector for 40-683 40-1311
roof wiring loom 40-992
40-1042
40-1110
40-677
40-764
40-769
40-772
D030 Wiring connector for 40-683 40-1311
central cab wiring 40-772
loom 40-992
40-1042
40-1110
40-677
40-764
40-769
D030 Wiring connector for [LNK] 40-1331
cab power wiring
loom
D030 Wiring connector for 40-683 40-1347
cab power wiring 40-992
loom 40-1042
40-1110
40-677
40-764
40-769
40-772
D030 Wiring connector for [LNK] 40-1410
cab power wiring
loom
D031 Wiring connector for 40-647 40-1311
central wiring loom 40-652
40-683
40-677
D031 Wiring connector for 40-647 40-1347
roof wiring loom 40-652
40-683
40-677
40-728

40-235
 Wiring diagrams
Table 153
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D032 Wiring connector for 40-677 40-1301
cab power wiring
loom
D032 Wiring connector for 40-647 40-1311
roof wiring loom 40-652
40-683
40-677
D033 Wiring connector for 40-677 40-1301
roof
D033 Wiring connector to 40-677 40-1301
wiring loom
D034 Wiring connector for 40-677 40-1301
roof
D034 Wiring connector to 40-677 40-1301
wiring loom
D035 Wiring connector for 40-843 40-1327
central wiring loom
and electronic lift
D037 Wiring connector 40-719 40-1410
40-1206
40-743
40-843
40-1087
D037 Wiring connector for 40-719 40-1410
switch wiring loom 40-1206
40-743
40-843
40-1087
D039 Wiring connector for 40-647 40-1295
central cab wiring 40-1186
loom 40-1206
40-1240
40-1110
40-1137
40-953
40-992
40-1042
40-1087
40-826
40-843
40-882
40-895
40-928
40-652
40-683
40-677
40-764
40-769
40-772

40-236
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D039 Wiring connector for 40-647 40-1347
power wiring loom 40-1186
40-1042
40-1087
40-1110
40-826
40-882
40-928
40-992
40-652
40-683
40-677
40-764
40-769
40-772
D039 Wiring connector for 40-843 40-1410
power wiring loom 40-1206
40-895
40-953
40-1087
40-1137
D040 Wiring connector for 40-604 40-1347
power wiring loom 40-1247
40-1042
40-1186
40-1240
40-882
40-928
40-992
40-769
40-772
40-826
40-647
40-652
40-683
40-677
40-705
40-728
40-764
D040 Wiring connector for 40-629 40-1410
power wiring loom 40-1087
40-1206
40-743
40-843
40-953

40-237
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D040 Wiring connector for 40-604 40-1295
central wiring loom 40-1186
40-1255
40-1206
40-1240
40-1247
40-1087
40-953
40-992
40-1042
40-882
40-895
40-928
40-772
40-826
40-843
40-769
40-629
40-647
40-652
40-683
40-677
40-705
40-719
40-728
40-743
40-764
D043 Wiring connector 40-728 40-1347
40-826
40-1186
40-1206
D043 Wiring connector for 40-728 40-1347
switch wiring loom 40-826
40-1186
40-1206
D044 Wiring connector for 40-764 40-1301
windscreen wiper
motor wiring loom
D044 Wiring connector for 40-764 40-1279
roof wiring loom
D045 Wiring connector for 40-772 40-1318
windscreen wiper
wiring loom
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D045 Wiring connector for 40-769 40-1276
roof wiring loom 40-772
D046 Wiring connector for 40-772 40-1318
work lights and wind- 40-992
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector for 40-992 40-1388
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab

40-238
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D046 Wiring connector to 40-769 40-1322
cab roof wiring loom, 40-772
versions with stan- 40-992
dard cab

Table 154
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-769 40-1322
rear screen wiper 40-772
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for 40-769 40-1300
work lights and wind- 40-772
screen wiper wiring
loom, versions with-
out high visibility cab
D050 Wiring connector for 40-928 40-1312
RH lower front head- 40-992
light 40-1042
D050 Wiring connector for 40-928 40-1427
low front lights wiring 40-992
loom 40-1042
D051 Wiring connector for 40-1042 40-1288
LH lower headlight
wiring loom
D051 2.8059.528.0 Wiring connector for 40-928 40-1427
front lower work light 40-992
wiring loom, ver- 40-1042
sions with high vis-
ibility cab
D052 Wiring connector for 40-928 40-1427
low front lights wiring 40-992
loom 40-1042
D052 Wiring connector for 40-928 40-1312
LH lower front head- 40-992
light 40-1042
D053 2.8059.528.0 Wiring connector for 40-928 40-1427
front lower work light 40-992
wiring loom, ver- 40-1042
sions with high vis-
ibility cab
D053 Wiring connector for [LNK] 40-1288
RH lower headlight
wiring loom
D055 Seat configuration [LNK] 40-1347
connector
D055a Seat configuration 40-826 40-1347
connector
D055b Seat configuration 40-826 40-1347
connector
D056 Seat configuration 40-843 40-1410
connector
D056a Seat configuration 40-843 40-1410
connector

40-239
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D056b Seat configuration 40-843 40-1410
connector
D058 Wiring connector 40-826 40-1347
40-882
D058 Wiring connector for 40-826 40-1347
parking brake wiring 40-882
loom
Table 155
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D059 Wiring connector 40-843 40-1410
40-895
D059 Wiring connector for 40-843 40-1410
parking brake wiring 40-895
loom
D062 Wiring connector for 40-928 40-1427
low front lights wiring 40-992
loom 40-1042
D062 Wiring connector for 40-928 40-1312
LH lower front head- 40-992
light 40-1042
D063 Wiring connector for 40-1042 40-1301
flashing beacon wir-
ing loom
D063 Wiring connector for 40-992 40-1322
flashing beacon wir-
ing loom
D063 Wiring connector for 40-992 40-1286
roof wiring loom 40-1042
D064 Wiring connector for 40-1042 40-1301
flashing beacon wir-
ing loom
D064 Wiring connector for 40-992 40-1322
flashing beacon wir-
ing loom
D064 Wiring connector for 40-992 40-1286
roof wiring loom 40-1042
D065 Wiring connector for 40-928 40-1285
central wiring loom
D065 Wiring connector for 40-928 40-1347
RH rear lights wiring
loom
D066 Wiring connector for 40-928 40-1285
central wiring loom
D066 Wiring connector for 40-928 40-1347
LH rear lights wiring
loom
D069 Wiring connector for [LNK] 40-1410
roof wiring loom
Table 156
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D070 Wiring connector for [LNK] 40-1410
windscreen washer
pump wiring loom

40-240
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D071 Wiring connector for [LNK] 40-1410
rear screen washer
pump wiring loom
D075 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
RH front work light
D076 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
LH front work light
D077 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
LH rear work light
D078 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
RH rear work light
D079 Wiring connector for [LNK] 40-1423
central wiring loom
D079 Wiring connector for 40-826 40-1347
HL lever wiring loom 40-1186
D079 Wiring connector for 40-843 40-1410
HL lever wiring loom 40-1206
D080 Wiring connector for [LNK] 40-1318
air conditioner
D081 Wiring connector for [LNK] 40-1318
condenser wiring
loom
D082 Wiring connector for 40-728 40-1327
front PTO control so- 40-743
lenoid valve 40-843
D082 Wiring connector for 40-728 40-1324
front PTO control so- 40-743
lenoid valve 40-843
D082 Wiring connector for 40-728 40-1281
engine wiring loom 40-743
D083 Wiring connector for 40-953 40-1317
central wiring loom
D083 Wiring connector for 40-953 40-1410
front lights wiring 40-1087
loom
D086 Wiring connector for 40-953 40-1285
central wiring loom
D086 Wiring connector for 40-953 40-1410
rear LH work light
wiring loom, USA
D087 Wiring connector for 40-953 40-1285
central wiring loom
D087 Wiring connector for 40-953 40-1410
rear RH work light
wiring loom
F004 04411920.4 Front LH sidelight 40-928 40-1427
and turn indicator

40-241
 Wiring diagrams
40.2.20 - D - Intermediate connections (AGROFARM 420 -> ZKDW390200TD25001)
ITA version
Table 157
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D001 Wiring connector 40-723 40-1331
40-1145
40-791
D001 Wiring connector for 40-723 40-1331
switch wiring loom 40-1145
40-791
D002 Wiring connector for 40-1099 40-1331
seat wiring loom
D002 Wiring connector for 40-1099 40-1279
central wiring loom
D003 Wiring connector for 40-791 40-1331
parking brake wiring 40-877
loom
D003 Wiring connector 40-791 40-1331
40-877
D003 Wiring connector for [LNK] [LNK]
parking brake wiring
loom
D004 Wiring connector for 40-596 40-1306
central wiring loom 40-1237
40-1166
40-1145
40-1076
40-942
40-915
40-877
40-889
40-807
40-807
40-701
40-714
40-723
40-738
40-791
40-621
D004 Wiring connector for 40-596 40-1331
rear wiring loom 40-723
40-791
40-877
40-915
40-1145
40-1237
40-701
D004 Wiring connector for 40-621 40-1392
rear wiring loom 40-889
40-942
40-1076
40-1166
40-807
40-714
40-738
D005 Wiring connector for 40-1237 40-1331
auxiliary distributor
control wiring loom
D005 Wiring connector for 40-1237 40-1364
central wiring loom

40-242
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D006 Wiring connector for 40-596 40-1331
reverse shuttle wir- 40-791
ing loom 40-1145
40-1247
D006 Wiring connector for 40-621 40-1392
reverse shuttle wir- 40-807
ing loom 40-1166
40-1255
D008 Seat configuration 40-791 40-1331
connector
D008a Seat configuration 40-791 40-1331
connector
D008b Seat configuration 40-791 40-1331
connector
D009 Wiring connector for 40-915 40-1312
central wiring loom 40-1024
40-976
D009 Wiring connector for 40-915 40-1331
front lights wiring 40-976
loom 40-1024
D010 Wiring connector for 40-596 40-1331
engine wiring loom 40-665
40-671
40-701
40-723
D010 Wiring connector for 40-621 40-1392
engine wiring loom 40-714
40-738
40-807
D010 Wiring connector for 40-596 40-1324
central wiring loom 40-723
40-738
40-807
40-701
40-714
40-665
40-671
40-621
D011 Wiring connector for 40-915 40-1309
central wiring loom 40-1130
40-1099
40-942
D011 Wiring connector for 40-915 40-1331
cowl lights wiring 40-976
loom 40-1024
40-1099
D011 Wiring connector for 40-942 40-1392
cowl lights wiring 40-1076
loom 40-1130
D012 Wiring connector for 40-637 40-1311
roof wiring loom 40-665
40-671
D012 Wiring connector for 40-671 40-1301
cab power wiring
loom
D012 Wiring connector for 40-641 40-1318
cab power wiring
loom

40-243
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D012 Wiring connector for 40-637 40-1388
cab power wiring 40-665
loom
D013 Wiring connector for 40-637 40-1331
power wiring loom 40-755
40-758
40-976
40-1024
40-1099
40-641
40-665
40-671
40-750
D013 Wiring connector for [LNK] 40-1392
power wiring loom
D013 Wiring connector for 40-637 40-1295
central wiring loom 40-1099
40-1024
40-976
40-807
40-641
40-758
40-755
40-750
40-671
40-665
D014 Wiring connector for 40-701 40-1425
rear wiring loom 40-714
D014 Wiring connector for 40-701 40-1306
engine wiring loom 40-807
40-714

Table 158
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D015 Wiring connector for 40-807 40-1306
trailer air brake wir- 40-877
ing loom 40-889
D015 Wiring connector for 40-877 40-1287
rear wiring loom 40-889
D017 Wiring connector for 40-807 40-1306
auxiliary distributor 40-1237
solenoid valves
D017 Wiring connector for 40-1237 40-1388
rear wiring loom
D018 Wiring connector for 40-807 40-1306
PTO sensor wiring
loom - (USA EX-
PORT)
D019 Wiring connector for 40-1076 40-1306
work light and rotat- 40-807
ing beacon wiring
loom
D019 Wiring connector for [LNK] 40-1292
rear wiring loom
D025 Wiring connector for 40-641 40-1318
heating wiring loom

40-244
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D025 Wiring connector for 40-637 40-1388
air conditioner wiring 40-665
loom
D025 Wiring connector for [LNK] 40-1274
roof wiring loom
D025 Wiring connector for [LNK] 40-1275
roof wiring loom
D026 Wiring connector for 40-665 40-1388
air conditioner wiring
loom
D026 Wiring connector for [LNK] 40-1275
roof wiring loom
D027 Wiring connector for 40-915 40-1312
RH lower front head- 40-1024
light 40-976
D027 Wiring connector for 40-915 40-1427
low front lights wiring 40-976
loom 40-1024
D028 Wiring connector for 40-671 40-1301
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1388
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1308
roof wiring loom 40-671
D029 Connection between 40-671 40-1301
cab power supply 40-1099
wiring and HV roof 40-750
40-1024
wiring
D029 Wiring connector for 40-671 40-1301
cab power wiring 40-1099
loom 40-750
40-1024
D029 Wiring connector for 40-758 40-1318
cab power wiring 40-976
loom
D029 Wiring connector for 40-665 40-1388
cab power wiring 40-976
loom
D029 Wiring connector for 40-665 40-1311
roof wiring loom 40-1024
40-1099
40-758
40-976
40-671
40-750
40-755
D030 Wiring connector for 40-665 40-1311
central cab wiring 40-1024
loom 40-1099
40-758
40-976
40-671
40-750
40-755

40-245
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D030 Wiring connector for 40-665 40-1331
cab power wiring 40-976
loom 40-1024
40-1099
40-671
40-750
40-755
40-758
D030 Wiring connector for [LNK] 40-1392
cab power wiring
loom
D031 Wiring connector for 40-637 40-1331
cab power wiring 40-641
loom 40-665
40-671
D031 Wiring connector for 40-637 40-1311
central wiring loom 40-665
40-671
40-641
Table 159
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D032 Wiring connector for 40-671 40-1301
cab power wiring
loom
D032 Wiring connector for 40-637 40-1311
roof wiring loom 40-665
40-671
40-641
D033 Wiring connector for 40-671 40-1301
roof
D033 Wiring connector to 40-671 40-1301
wiring loom
D034 Wiring connector for 40-671 40-1301
roof
D034 Wiring connector to 40-671 40-1301
wiring loom
D035 Wiring connector for 40-807 40-1327
central wiring loom
and electronic lift
D036 Wiring connector 40-714 40-1392
40-1076
40-1166
40-807
40-738
D036 Wiring connector for 40-714 40-1392
switch wiring loom 40-1076
40-1166
40-807
40-738

40-246
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D039 Wiring connector for 40-637 40-1295
central cab wiring 40-1237
loom 40-1166
40-1130
40-1145
40-1076
40-942
40-889
40-915
40-877
40-791
40-1099
40-1024
40-976
40-807
40-641
40-758
40-755
40-750
40-671
40-665
D039 Wiring connector for 40-637 40-1331
power wiring loom 40-1145
40-1237
40-758
40-791
40-877
40-915
40-976
40-1024
40-1099
40-641
40-665
40-671
40-750
40-755
D039 Wiring connector for 40-807 40-1392
power wiring loom 40-1166
40-942
40-1076
40-1130
40-889
D040 Wiring connector for 40-621 40-1392
power wiring loom 40-942
40-1076
40-1166
40-1255
40-714
40-738
40-807
40-889

40-247
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D040 Wiring connector for 40-596 40-1331
power wiring loom 40-1024
40-1145
40-1237
40-1247
40-791
40-877
40-915
40-976
40-723
40-750
40-755
40-758
40-701
40-637
40-641
40-665
40-671
D040 Wiring connector for 40-596 40-1295
central wiring loom 40-1255
40-1247
40-1237
40-1166
40-1145
40-1076
40-1024
40-976
40-758
40-791
40-807
40-877
40-889
40-915
40-942
40-637
40-641
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-621
D044 Wiring connector for 40-750 40-1301
windscreen wiper
motor wiring loom
D044 Wiring connector for 40-750 40-1279
roof wiring loom
D045 Wiring connector for 40-758 40-1318
windscreen wiper
wiring loom
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D045 Wiring connector for [LNK] 40-1276
[LNK]

40-248
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D046 Wiring connector for 40-758 40-1318
work lights and wind- 40-976
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector for 40-976 40-1388
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector to 40-755 40-1322
cab roof wiring loom, 40-976
versions with stan- 40-758
dard cab

Table 160
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-755 40-1322
rear screen wiper 40-758
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for 40-758 40-1300
work lights and wind- 40-755
screen wiper wiring
loom, versions with-
out high visibility cab
D048 Wiring connector 40-807 40-1392
40-889
D048 Wiring connector for 40-807 40-1392
parking brake wiring 40-889
loom
D049 Seat configuration 40-807 40-1392
connector
D049a Seat configuration 40-807 40-1392
connector
D049b Seat configuration 40-807 40-1392
connector
D050 Wiring connector for 40-915 40-1312
RH lower front head- 40-1024
light 40-976
D050 Wiring connector for 40-915 40-1427
low front lights wiring 40-976
loom 40-1024
D051 Wiring connector for 40-1024 40-1288
LH lower headlight
wiring loom
D051 2.8059.528.0 Wiring connector for 40-915 40-1427
front lower work light 40-976
wiring loom, ver- 40-1024
sions with high vis-
ibility cab
D052 Wiring connector for 40-915 40-1427
low front lights wiring 40-976
loom 40-1024

40-249
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D052 Wiring connector for 40-915 40-1312
LH lower front head- 40-1024
light 40-976
D053 2.8059.528.0 Wiring connector for 40-915 40-1427
front lower work light 40-976
wiring loom, ver- 40-1024
sions with high vis-
ibility cab
D053 Wiring connector for 40-1024 40-1288
RH lower headlight
wiring loom

Table 161
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D060 Wiring connector for 40-877 40-1331
rear RH work light 40-915
wiring loom
D060 Wiring connector for 40-889 40-1392
rear RH work light 40-942
wiring loom
D060 Wiring connector for 40-877 40-1391
central wiring loom 40-942
40-915
40-889
D061 Wiring connector for 40-877 40-1391
central wiring loom 40-942
40-915
40-889
D061 Wiring connector for 40-877 40-1331
rear LH work light 40-915
wiring loom
D061 Wiring connector for 40-889 40-1392
rear LH work light 40-942
wiring loom
D062 Wiring connector for 40-915 40-1427
low front lights wiring 40-976
loom 40-1024
D062 Wiring connector for 40-915 40-1312
LH lower front head- 40-1024
light 40-976
D063 Wiring connector for 40-1024 40-1301
flashing beacon wir-
ing loom
D063 Wiring connector for 40-976 40-1322
flashing beacon wir-
ing loom
D063 Wiring connector for 40-976 40-1286
roof wiring loom 40-1024
D064 Wiring connector for 40-1024 40-1301
flashing beacon wir-
ing loom
D064 Wiring connector for 40-976 40-1322
flashing beacon wir-
ing loom
D064 Wiring connector for 40-976 40-1286
roof wiring loom 40-1024

40-250
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D067 Wiring connector for [LNK] 40-1392
windscreen washer
pump wiring loom
D068 Wiring connector for [LNK] 40-1392
roof wiring loom
Table 162
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D072 Wiring connector for [LNK] 40-1392
windscreen washer
pump wiring loom
D075 Wiring connector for 40-1024 40-1424
roof wiring loom
D075 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
RH front work light
D076 Wiring connector for 40-1024 40-1424
roof wiring loom
D076 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
LH front work light
D077 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
LH rear work light
D078 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
RH rear work light
D079 Wiring connector for 40-791 40-1331
HL lever wiring loom 40-1145
D079 Wiring connector for 40-807 40-1392
central wiring loom 40-1166
D080 Wiring connector for [LNK] 40-1318
air conditioner
D081 Wiring connector for [LNK] 40-1318
condenser wiring
loom
D082 Wiring connector for 40-807 40-1327
front PTO control so- 40-723
lenoid valve 40-738
D082 Wiring connector for 40-723 40-1324
front PTO control so- 40-738
lenoid valve 40-807
D082 Wiring connector for 40-723 40-1281
engine wiring loom 40-738
D083 Wiring connector for 40-942 40-1317
central wiring loom
D083 Wiring connector for 40-942 40-1392
front lights wiring 40-1076
loom
D086 Wiring connector for [LNK] 40-1285
central wiring loom
D087 Wiring connector for [LNK] 40-1285
central wiring loom
F004 04411920.4 Front LH sidelight 40-915 40-1427
and turn indicator

40-251
 Wiring diagrams
USA version
Table 163
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D002 Wiring connector for [LNK] 40-1279
central wiring loom
D004 Wiring connector for 40-604 40-1306
central wiring loom 40-928
40-953
40-1087
40-1186
40-1206
40-1240
40-843
40-882
40-895
40-743
40-826
40-719
40-728
40-629
40-705
D004 Wiring connector for 40-604 40-1347
rear wiring loom 40-1240
40-1186
40-882
40-928
40-705
40-728
40-826
D004 Wiring connector for 40-629 40-1410
rear wiring loom 40-895
40-953
40-1087
40-1206
40-719
40-743
40-843
D005 Wiring connector for 40-1237 40-1364
central wiring loom
D005 Wiring connector for 40-1240 40-1347
auxiliary distributor
control wiring loom
D006 Wiring connector for 40-604 40-1347
reverse shuttle wir- 40-1247
ing loom 40-826
40-1186
40-1206
D006 Wiring connector for 40-629 40-1410
reverse shuttle wir- 40-843
ing loom 40-1206
D009 Wiring connector for 40-928 40-1312
central wiring loom 40-992
40-1042
D009 Wiring connector for 40-928 40-1347
front lights wiring 40-1042
loom 40-992
D010 Wiring connector for 40-629 40-1410
engine wiring loom 40-719
40-743
40-843

40-252
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D010 Wiring connector for 40-604 40-1347
front wiring loom 40-728
40-826
40-683
40-677
40-705
D010 Wiring connector for 40-604 40-1324
central wiring loom 40-743
40-843
40-719
40-728
40-705
40-629
40-683
40-677
D011 Wiring connector for 40-928 40-1309
central wiring loom 40-1110
40-1137
40-953
D011 Wiring connector for 40-928 40-1347
cowl lights wiring 40-992
loom 40-1042
40-1110
D011 Wiring connector for 40-953 40-1410
cowl lights wiring 40-1087
loom 40-1137
D012 Wiring connector for 40-647 40-1311
roof wiring loom 40-683
40-677
40-652
D012 Wiring connector for 40-677 40-1301
cab power wiring
loom
D012 Wiring connector for 40-652 40-1318
cab power wiring
loom
D012 Wiring connector for 40-647 40-1388
cab power wiring 40-683
loom
D013 Wiring connector for 40-647 40-1347
power wiring loom 40-1110
40-772
40-992
40-1042
40-683
40-677
40-764
40-769
D013 Wiring connector for [LNK] 40-1410
power wiring loom

40-253
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D013 Wiring connector for 40-647 40-1295
central wiring loom 40-1110
40-843
40-992
40-1042
40-764
40-769
40-772
40-826
40-652
40-683
40-677
D014 Wiring connector for 40-705 40-1425
rear wiring loom 40-719
D014 Wiring connector for 40-705 40-1306
engine wiring loom 40-719
40-843
40-882
Table 164
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D015 Wiring connector for 40-843 40-1306
trailer air brake wir- 40-882
ing loom 40-895
D017 Wiring connector for 40-843 40-1306
auxiliary distributor 40-1240
solenoid valves
D017 Wiring connector for 40-1240 40-1388
rear wiring loom
D018 Wiring connector for 40-728 40-1300
central wiring loom 40-743
D018 Wiring connector for 40-728 40-1306
PTO sensor wiring 40-843
loom - (USA EX- 40-743
PORT)
D019 Wiring connector for 40-843 40-1306
work light and rotat- 40-1087
ing beacon wiring
loom
D019 Wiring connector for 40-1087 40-1292
rear wiring loom
D025 Wiring connector for 40-652 40-1318
heating wiring loom
D025 Wiring connector for 40-647 40-1388
air conditioner wiring 40-683
loom
D025 Wiring connector for 40-647 40-1274
roof wiring loom 40-652
D025 Wiring connector for 40-683 40-1275
roof wiring loom
D026 Wiring connector for 40-683 40-1388
air conditioner wiring
loom
D026 Wiring connector for 40-683 40-1275
roof wiring loom

40-254
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D027 Wiring connector for 40-928 40-1312
RH lower front head- 40-992
light 40-1042
D027 Wiring connector for 40-928 40-1427
low front lights wiring 40-992
loom 40-1042
D028 Wiring connector for 40-677 40-1301
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1388
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1308
roof wiring loom 40-677
D029 Connection between 40-677 40-1301
cab power supply 40-1042
wiring and HV roof 40-1110
40-764
wiring
D029 Wiring connector for 40-677 40-1301
cab power wiring 40-1042
loom 40-1110
40-764
D029 Wiring connector for 40-772 40-1318
cab power wiring 40-992
loom
D029 Wiring connector for 40-683 40-1388
cab power wiring 40-992
loom
D029 Wiring connector for 40-683 40-1311
roof wiring loom 40-992
40-1042
40-1110
40-677
40-764
40-769
40-772
D030 Wiring connector for 40-683 40-1311
central cab wiring 40-772
loom 40-992
40-1042
40-1110
40-677
40-764
40-769
D030 Wiring connector for [LNK] 40-1331
cab power wiring
loom
D030 Wiring connector for 40-683 40-1347
cab power wiring 40-992
loom 40-1042
40-1110
40-677
40-764
40-769
40-772

40-255
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D030 Wiring connector for [LNK] 40-1410
cab power wiring
loom
D031 Wiring connector for 40-647 40-1311
central wiring loom 40-652
40-683
40-677
D031 Wiring connector for 40-647 40-1347
roof wiring loom 40-652
40-683
40-677
40-728
Table 165
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D032 Wiring connector for 40-677 40-1301
cab power wiring
loom
D032 Wiring connector for 40-647 40-1311
roof wiring loom 40-652
40-683
40-677
D033 Wiring connector for 40-677 40-1301
roof
D033 Wiring connector to 40-677 40-1301
wiring loom
D034 Wiring connector for 40-677 40-1301
roof
D034 Wiring connector to 40-677 40-1301
wiring loom
D035 Wiring connector for 40-843 40-1327
central wiring loom
and electronic lift
D037 Wiring connector 40-719 40-1410
40-1206
40-743
40-843
40-1087
D037 Wiring connector for 40-719 40-1410
switch wiring loom 40-1206
40-743
40-843
40-1087

40-256
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D039 Wiring connector for 40-647 40-1295
central cab wiring 40-1186
loom 40-1206
40-1240
40-1110
40-1137
40-953
40-992
40-1042
40-1087
40-826
40-843
40-882
40-895
40-928
40-652
40-683
40-677
40-764
40-769
40-772
D039 Wiring connector for 40-647 40-1347
power wiring loom 40-1186
40-1042
40-1087
40-1110
40-826
40-882
40-928
40-992
40-652
40-683
40-677
40-764
40-769
40-772
D039 Wiring connector for 40-843 40-1410
power wiring loom 40-1206
40-895
40-953
40-1087
40-1137
D040 Wiring connector for 40-604 40-1347
power wiring loom 40-1247
40-1042
40-1186
40-1240
40-882
40-928
40-992
40-769
40-772
40-826
40-647
40-652
40-683
40-677
40-705
40-728
40-764

40-257
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D040 Wiring connector for 40-629 40-1410
power wiring loom 40-1087
40-1206
40-743
40-843
40-953
D040 Wiring connector for 40-604 40-1295
central wiring loom 40-1186
40-1255
40-1206
40-1240
40-1247
40-1087
40-953
40-992
40-1042
40-882
40-895
40-928
40-772
40-826
40-843
40-769
40-629
40-647
40-652
40-683
40-677
40-705
40-719
40-728
40-743
40-764
D043 Wiring connector 40-728 40-1347
40-826
40-1186
40-1206
D043 Wiring connector for 40-728 40-1347
switch wiring loom 40-826
40-1186
40-1206
D044 Wiring connector for 40-764 40-1301
windscreen wiper
motor wiring loom
D044 Wiring connector for 40-764 40-1279
roof wiring loom
D045 Wiring connector for 40-772 40-1318
windscreen wiper
wiring loom
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D045 Wiring connector for 40-769 40-1276
roof wiring loom 40-772
D046 Wiring connector for 40-772 40-1318
work lights and wind- 40-992
screen wiper wiring
loom, versions with-
out high visibility cab

40-258
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D046 Wiring connector for 40-992 40-1388
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector to 40-769 40-1322
cab roof wiring loom, 40-772
versions with stan- 40-992
dard cab

Table 166
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-769 40-1322
rear screen wiper 40-772
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for 40-769 40-1300
work lights and wind- 40-772
screen wiper wiring
loom, versions with-
out high visibility cab
D050 Wiring connector for 40-928 40-1312
RH lower front head- 40-992
light 40-1042
D050 Wiring connector for 40-928 40-1427
low front lights wiring 40-992
loom 40-1042
D051 Wiring connector for 40-1042 40-1288
LH lower headlight
wiring loom
D051 2.8059.528.0 Wiring connector for 40-928 40-1427
front lower work light 40-992
wiring loom, ver- 40-1042
sions with high vis-
ibility cab
D052 Wiring connector for 40-928 40-1427
low front lights wiring 40-992
loom 40-1042
D052 Wiring connector for 40-928 40-1312
LH lower front head- 40-992
light 40-1042
D053 2.8059.528.0 Wiring connector for 40-928 40-1427
front lower work light 40-992
wiring loom, ver- 40-1042
sions with high vis-
ibility cab
D053 Wiring connector for [LNK] 40-1288
RH lower headlight
wiring loom
D055 Seat configuration [LNK] 40-1347
connector
D055a Seat configuration 40-826 40-1347
connector

40-259
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D055b Seat configuration 40-826 40-1347
connector
D056 Seat configuration 40-843 40-1410
connector
D056a Seat configuration 40-843 40-1410
connector
D056b Seat configuration 40-843 40-1410
connector
D058 Wiring connector 40-826 40-1347
40-882
D058 Wiring connector for 40-826 40-1347
parking brake wiring 40-882
loom
Table 167
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D059 Wiring connector 40-843 40-1410
40-895
D059 Wiring connector for 40-843 40-1410
parking brake wiring 40-895
loom
D062 Wiring connector for 40-928 40-1427
low front lights wiring 40-992
loom 40-1042
D062 Wiring connector for 40-928 40-1312
LH lower front head- 40-992
light 40-1042
D063 Wiring connector for 40-1042 40-1301
flashing beacon wir-
ing loom
D063 Wiring connector for 40-992 40-1322
flashing beacon wir-
ing loom
D063 Wiring connector for 40-992 40-1286
roof wiring loom 40-1042
D064 Wiring connector for 40-1042 40-1301
flashing beacon wir-
ing loom
D064 Wiring connector for 40-992 40-1322
flashing beacon wir-
ing loom
D064 Wiring connector for 40-992 40-1286
roof wiring loom 40-1042
D065 Wiring connector for 40-928 40-1285
central wiring loom
D065 Wiring connector for 40-928 40-1347
RH rear lights wiring
loom
D066 Wiring connector for 40-928 40-1285
central wiring loom
D066 Wiring connector for 40-928 40-1347
LH rear lights wiring
loom
D069 Wiring connector for [LNK] 40-1410
roof wiring loom

40-260
Wiring diagrams
Table 168
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D070 Wiring connector for [LNK] 40-1410
windscreen washer
pump wiring loom
D071 Wiring connector for [LNK] 40-1410
rear screen washer
pump wiring loom
D075 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
RH front work light
D076 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
LH front work light
D077 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
LH rear work light
D078 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
RH rear work light
D079 Wiring connector for [LNK] 40-1423
central wiring loom
D079 Wiring connector for 40-826 40-1347
HL lever wiring loom 40-1186
D079 Wiring connector for 40-843 40-1410
HL lever wiring loom 40-1206
D080 Wiring connector for [LNK] 40-1318
air conditioner
D081 Wiring connector for [LNK] 40-1318
condenser wiring
loom
D082 Wiring connector for 40-728 40-1327
front PTO control so- 40-743
lenoid valve 40-843
D082 Wiring connector for 40-728 40-1324
front PTO control so- 40-743
lenoid valve 40-843
D082 Wiring connector for 40-728 40-1281
engine wiring loom 40-743
D083 Wiring connector for 40-953 40-1317
central wiring loom
D083 Wiring connector for 40-953 40-1410
front lights wiring 40-1087
loom
D086 Wiring connector for 40-953 40-1285
central wiring loom
D086 Wiring connector for 40-953 40-1410
rear LH work light
wiring loom, USA
D087 Wiring connector for 40-953 40-1285
central wiring loom
D087 Wiring connector for 40-953 40-1410
rear RH work light
wiring loom
F004 04411920.4 Front LH sidelight 40-928 40-1427
and turn indicator

40-261
 Wiring diagrams
40.2.21 - D - Intermediate connections (AGROFARM 430 -> ZKDW430200TD25001)
ITA version
Table 169
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D001 Wiring connector 40-723 40-1331
40-1145
40-791
D001 Wiring connector for 40-723 40-1331
switch wiring loom 40-1145
40-791
D002 Wiring connector for 40-1099 40-1331
seat wiring loom
D002 Wiring connector for 40-1120 40-1365
seat wiring loom
D003 Wiring connector for 40-791 40-1331
parking brake wiring 40-877
loom
D003 Wiring connector 40-791 40-1331
40-877
D003 Wiring connector for [LNK] [LNK]
parking brake wiring
loom
D004 Wiring connector for 40-596 40-1306
central wiring loom 40-1237
40-1166
40-1145
40-1076
40-942
40-915
40-877
40-889
40-807
40-807
40-701
40-714
40-723
40-738
40-791
40-621
D004 Wiring connector for 40-596 40-1331
rear wiring loom 40-723
40-791
40-877
40-915
40-1145
40-1237
40-701
D004 Wiring connector for 40-621 40-1392
rear wiring loom 40-738
40-889
40-942
40-1076
40-1166
40-807
40-714
D005 Wiring connector for 40-1237 40-1364
central wiring loom 40-1243
D005 Wiring connector for 40-1237 40-1331
auxiliary distributor
control wiring loom

40-262
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D005 Wiring connector for 40-1243 40-1365
auxiliary distributor
control wiring loom
D006 Wiring connector for 40-596 40-1331
reverse shuttle wir- 40-791
ing loom 40-1145
40-1247
D006 Wiring connector for 40-613 40-1365
reverse shuttle wir- 40-862
ing loom 40-1262
40-1226
D006 Wiring connector for 40-621 40-1392
reverse shuttle wir- 40-807
ing loom 40-1166
40-1255
D007 Reverse shuttle 40-1262 40-1365
CAN configuration
connector
D007 Reverse shuttle 40-1262 40-1365
CAN configuration
connector
D008 Seat configuration 40-791 40-1331
connector
D008a Seat configuration 40-791 40-1331
connector
D008b Seat configuration 40-791 40-1331
connector
D009 Wiring connector for 40-915 40-1312
central wiring loom 40-1059
40-1008
40-964
40-1024
40-976
D009 Wiring connector for 40-915 40-1331
front lights wiring 40-976
loom 40-1024
D009 Wiring connector for 40-964 40-1365
front lights wiring 40-1059
loom 40-1008
D010 Wiring connector for 40-596 40-1331
engine wiring loom 40-665
40-671
40-701
40-723
D010 Wiring connector for 40-621 40-1392
engine wiring loom 40-738
40-714
40-807
D010 Wiring connector for 40-613 40-1365
front wiring loom 40-734
40-710
40-695
40-689

40-263
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D010 Wiring connector for 40-596 40-1324
central wiring loom 40-738
40-734
40-710
40-695
40-689
40-613
40-723
40-807
40-701
40-714
40-665
40-671
40-621
D011 Wiring connector for 40-915 40-1309
central wiring loom 40-1120
40-964
40-1130
40-1099
40-942
D011 Wiring connector for 40-915 40-1331
cowl lights wiring 40-976
loom 40-1024
40-1099
D011 Wiring connector for 40-964 40-1365
cowl lights wiring 40-1120
loom 40-1059
40-1008
D011 Wiring connector for 40-942 40-1392
cowl lights wiring 40-1076
loom 40-1130
D012 Wiring connector for 40-637 40-1311
roof wiring loom 40-660
40-695
40-689
40-657
40-665
40-671
D012 Wiring connector for 40-671 40-1301
cab power wiring 40-695
loom
D012 Wiring connector for 40-641 40-1318
cab power wiring 40-660
loom
D012 Wiring connector for 40-637 40-1388
cab power wiring 40-689
loom 40-657
40-665
D013 Wiring connector for 40-637 40-1331
power wiring loom 40-755
40-758
40-976
40-1024
40-1099
40-641
40-665
40-671
40-750

40-264
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D013 Wiring connector for 40-657 40-1365
power wiring loom 40-660
40-1120
40-1059
40-1008
40-787
40-783
40-778
40-695
40-689
D013 Wiring connector for [LNK] 40-1392
power wiring loom
D013 Wiring connector for 40-637 40-1295
central wiring loom 40-660
40-1120
40-1059
40-1008
40-787
40-783
40-778
40-695
40-689
40-657
40-1099
40-1024
40-976
40-807
40-641
40-758
40-755
40-750
40-671
40-665
D014 Wiring connector for 40-701 40-1306
engine wiring loom 40-807
40-714
D014 Wiring connector for 40-710 40-1385
engine wiring loom
D014 Wiring connector for 40-701 40-1425
rear wiring loom 40-710
40-714

40-265
 Wiring diagrams
Table 170
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D015 Wiring connector for 40-807 40-1306
trailer air brake wir- 40-877
ing loom 40-889
D015 Wiring connector for [LNK] 40-1385
trailer air brake wir-
ing loom
D015 Wiring connector for 40-877 40-1287
rear wiring loom 40-889
D016 Wiring connector 40-1243 40-1385
for auxiliary distribu-
tor wiring loom, with
electronic lift
D016 Wiring connector for 40-1243 40-1365
rear wiring loom
D017 Wiring connector for 40-1237 40-1388
rear wiring loom
D017 Wiring connector for 40-807 40-1306
auxiliary distributor 40-1237
solenoid valves
D018 Wiring connector for 40-807 40-1306
PTO sensor wiring
loom - (USA EX-
PORT)
D018 Wiring connector for 40-734 40-1385
PTO sensor wiring
loom - (USA EX-
PORT)
D019 Wiring connector for 40-1076 40-1306
work light and rotat- 40-807
ing beacon wiring
loom
D019 Wiring connector for [LNK] 40-1292
rear wiring loom
D020 Wiring connector [LNK] 40-1385
D021 Wiring connector for 40-902 40-1385
trailer brake solenoid 40-862
valve
D022 Wiring connector for 40-710 40-1385
central wiring loom 40-862
40-1269
40-1243
40-1226
40-902
40-734
D022 Wiring connector for 40-613 40-1365
rear wiring loom 40-862
40-1269
40-1243
40-1226
40-964
40-902
40-734
40-710
D023 Wiring connector 40-1269 40-1382
for rear wiring loom,
with electronic lift

40-266
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D023 Wiring connector for 40-1269 40-1385
electronic lift wiring
loom
D024 Wiring connector 40-1269 40-1382
for rear wiring loom,
with electronic lift
D024 Wiring connector for 40-1269 40-1385
electronic lift wiring
loom
D025 Wiring connector for 40-641 40-1318
heating wiring loom 40-660
D025 Wiring connector for 40-637 40-1388
air conditioner wiring 40-689
loom 40-657
40-665
D025 Wiring connector for 40-657 40-1274
roof wiring loom 40-660
D025 Wiring connector for 40-689 40-1275
roof wiring loom
D026 Wiring connector for 40-665 40-1388
air conditioner wiring 40-689
loom
D026 Wiring connector for 40-689 40-1275
roof wiring loom
D027 Wiring connector for 40-915 40-1312
RH lower front head- 40-1059
light 40-1008
40-964
40-1024
40-976
D027 Wiring connector for 40-915 40-1427
low front lights wiring 40-1059
loom 40-1008
40-964
40-976
40-1024
D028 Wiring connector for 40-671 40-1301
air conditioner heat 40-695
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1388
air conditioner heat 40-689
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1308
roof wiring loom 40-695
40-689
40-671
D029 Connection between 40-671 40-1301
cab power supply 40-1120
wiring and HV roof 40-1059
40-778
wiring
40-695
40-1099
40-750
40-1024

40-267
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D029 Wiring connector for 40-671 40-1301
cab power wiring 40-1120
loom 40-1059
40-778
40-695
40-1099
40-750
40-1024
D029 Wiring connector for 40-758 40-1318
cab power wiring 40-976
loom
D029 Wiring connector for 40-665 40-1388
cab power wiring 40-1008
loom 40-689
40-976
D029 Wiring connector for 40-665 40-1311
roof wiring loom 40-1120
40-1059
40-1008
40-787
40-783
40-778
40-695
40-689
40-1024
40-1099
40-758
40-976
40-671
40-750
40-755
D030 Wiring connector for 40-665 40-1311
central cab wiring 40-1120
loom 40-1059
40-1008
40-787
40-783
40-778
40-695
40-689
40-1024
40-1099
40-758
40-976
40-671
40-750
40-755
D030 Wiring connector for 40-665 40-1331
cab power wiring 40-976
loom 40-1024
40-1099
40-671
40-750
40-755
40-758

40-268
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D030 Wiring connector for 40-689 40-1365
cab power wiring 40-1120
loom 40-1059
40-1008
40-787
40-783
40-778
40-695
D030 Wiring connector for [LNK] 40-1392
cab power wiring
loom
D031 Wiring connector for 40-637 40-1331
cab power wiring 40-641
loom 40-665
40-671
D031 Wiring connector for 40-657 40-1365
roof wiring loom 40-660
40-695
40-689
D031 Wiring connector for 40-637 40-1311
central wiring loom 40-660
40-695
40-689
40-657
40-665
40-671
40-641
Table 171
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D032 Wiring connector for 40-671 40-1301
cab power wiring 40-695
loom
D032 Wiring connector for 40-637 40-1311
roof wiring loom 40-660
40-695
40-689
40-657
40-665
40-671
40-641
D033 Wiring connector for 40-671 40-1301
roof 40-695
D033 Wiring connector to 40-671 40-1301
wiring loom 40-695
D034 Wiring connector for 40-671 40-1301
roof 40-695
D034 Wiring connector to 40-671 40-1301
wiring loom 40-695
D035 Wiring connector for 40-807 40-1327
central wiring loom
and electronic lift
D036 Wiring connector 40-714 40-1392
40-1076
40-1166
40-807
40-738

40-269
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D036 Wiring connector for 40-714 40-1392
switch wiring loom 40-738
40-1076
40-1166
40-807
D038 Wiring connector for 40-710 40-1386
central wiring loom 40-734
and electronic lift
D038 Wiring connector for 40-710 40-1365
RH side console wir- 40-734
ing loom
D039 Wiring connector for 40-637 40-1295
central cab wiring 40-862
loom 40-660
40-1269
40-1262
40-1243
40-1226
40-1120
40-1059
40-1008
40-964
40-902
40-787
40-783
40-778
40-695
40-689
40-657
40-1237
40-1166
40-1130
40-1145
40-1076
40-942
40-889
40-915
40-877
40-791
40-1099
40-1024
40-976
40-807
40-641
40-758
40-755
40-750
40-671
40-665

40-270
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D039 Wiring connector for 40-637 40-1331
power wiring loom 40-1145
40-1237
40-758
40-791
40-877
40-915
40-976
40-1024
40-1099
40-641
40-665
40-671
40-750
40-755
D039 Wiring connector for 40-657 40-1365
power wiring loom 40-862
40-660
40-1269
40-1262
40-1243
40-1226
40-1120
40-1059
40-1008
40-964
40-902
40-787
40-783
40-778
40-695
40-689
D039 Wiring connector for 40-807 40-1392
power wiring loom 40-1166
40-942
40-1076
40-1130
40-889
D040 Wiring connector for 40-621 40-1392
power wiring loom 40-738
40-714
40-942
40-1076
40-1166
40-1255
40-807
40-889

40-271
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D040 Wiring connector for 40-613 40-1365
power wiring loom 40-862
40-660
40-1269
40-1262
40-1243
40-1226
40-1059
40-1008
40-964
40-902
40-787
40-783
40-778
40-734
40-710
40-695
40-689
40-657
D040 Wiring connector for 40-596 40-1331
power wiring loom 40-1024
40-1145
40-1237
40-1247
40-791
40-877
40-915
40-976
40-723
40-750
40-755
40-758
40-701
40-637
40-641
40-665
40-671

40-272
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D040 Wiring connector for 40-596 40-1295
central wiring loom 40-862
40-660
40-1269
40-1262
40-1243
40-1226
40-1059
40-1008
40-964
40-902
40-783
40-778
40-734
40-714
40-710
40-695
40-689
40-657
40-613
40-1255
40-1247
40-1237
40-1166
40-1145
40-1076
40-1024
40-976
40-758
40-791
40-807
40-877
40-889
40-915
40-942
40-637
40-641
40-665
40-671
40-701
40-723
40-738
40-750
40-755
40-621
D044 Wiring connector for 40-750 40-1301
windscreen wiper 40-778
motor wiring loom
D044 Wiring connector for 40-750 40-1279
roof wiring loom 40-778
D045 Wiring connector for 40-758 40-1318
windscreen wiper
wiring loom
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D045 Wiring connector for 40-783 40-1276
roof wiring loom 40-787

40-273
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D046 Wiring connector for 40-758 40-1318
work lights and wind- 40-976
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector for 40-976 40-1388
work lights and wind- 40-1008
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector to 40-755 40-1322
cab roof wiring loom, 40-1008
versions with stan- 40-787
40-783
dard cab
40-976
40-758

Table 172
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-755 40-1322
rear screen wiper 40-787
wiring loom, ver- 40-783
40-758
sions without high
visibility cab
D047 Wiring connector for 40-758 40-1300
work lights and wind- 40-787
screen wiper wiring 40-783
40-755
loom, versions with-
out high visibility cab
D048 Wiring connector 40-807 40-1392
40-889
D048 Wiring connector for 40-807 40-1392
parking brake wiring 40-889
loom
D049 Seat configuration 40-807 40-1392
connector
D049a Seat configuration 40-807 40-1392
connector
D049b Seat configuration 40-807 40-1392
connector
D050 Wiring connector for 40-915 40-1312
RH lower front head- 40-1059
light 40-1008
40-964
40-1024
40-976
D050 Wiring connector for 40-915 40-1427
low front lights wiring 40-1059
loom 40-1008
40-964
40-976
40-1024
D051 Wiring connector for 40-1024 40-1288
LH lower headlight
wiring loom

40-274
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D051 2.8059.528.0 Wiring connector for 40-915 40-1427
front lower work light 40-1059
wiring loom, ver- 40-1008
40-964
sions with high vis-
40-976
ibility cab 40-1024
D052 Wiring connector for 40-915 40-1427
low front lights wiring 40-1059
loom 40-1008
40-964
40-976
40-1024
D052 Wiring connector for 40-915 40-1312
LH lower front head- 40-1059
light 40-1008
40-964
40-1024
40-976
D053 2.8059.528.0 Wiring connector for 40-915 40-1427
front lower work light 40-1059
wiring loom, ver- 40-1008
40-964
sions with high vis-
40-976
ibility cab 40-1024
D053 Wiring connector for 40-1024 40-1288
RH lower headlight
wiring loom
D054 Seat configuration 40-862 40-1365
connector
D054a Seat configuration 40-862 40-1365
connector
D054b Seat configuration 40-862 40-1365
connector
D057 Wiring connector for 40-902 40-1365
parking brake wiring 40-862
loom
D057 Wiring connector 40-902 40-1365
40-862

40-275
 Wiring diagrams
Table 173
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D060 Wiring connector for 40-877 40-1391
central wiring loom 40-964
40-902
40-889
40-915
40-942
D060 Wiring connector for 40-877 40-1331
rear RH work light 40-915
wiring loom
D060 Wiring connector for 40-902 40-1365
rear RH work light 40-964
wiring loom
D060 Wiring connector for 40-889 40-1392
rear RH work light 40-942
wiring loom
D061 Wiring connector for 40-902 40-1391
central wiring loom 40-964
D061 Wiring connector for 40-877 40-1331
rear LH work light 40-915
wiring loom
D061 Wiring connector for 40-902 40-1365
rear LH work light 40-964
wiring loom
D061 Wiring connector for 40-889 40-1392
rear LH work light 40-942
wiring loom
D062 Wiring connector for 40-915 40-1427
low front lights wiring 40-1059
loom 40-1008
40-964
40-976
40-1024
D062 Wiring connector for 40-915 40-1312
LH lower front head- 40-1059
light 40-1008
40-964
40-1024
40-976
D063 Wiring connector for 40-1024 40-1301
flashing beacon wir- 40-1059
ing loom
D063 Wiring connector for 40-976 40-1322
flashing beacon wir- 40-1008
ing loom
D063 Wiring connector for 40-976 40-1286
roof wiring loom 40-1059
40-1008
40-1024
D064 Wiring connector for 40-1024 40-1301
flashing beacon wir- 40-1059
ing loom
D064 Wiring connector for 40-976 40-1322
flashing beacon wir- 40-1008
ing loom

40-276
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D064 Wiring connector for 40-976 40-1286
roof wiring loom 40-1059
40-1008
40-1024
D067 Wiring connector for [LNK] 40-1392
windscreen washer
pump wiring loom
D068 Wiring connector for [LNK] 40-1392
roof wiring loom
Table 174
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D072 Wiring connector for [LNK] 40-1392
windscreen washer
pump wiring loom
D075 Wiring connector for 40-1024 40-1424
roof wiring loom 40-1059
D075 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
RH front work light 40-1059
D076 Wiring connector for 40-1024 40-1424
roof wiring loom 40-1059
D076 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
LH front work light 40-1059
D077 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
LH rear work light 40-1059
D078 2.8039.298.0/20 Wiring connector for 40-1024 40-1301
RH rear work light 40-1059
D079 Wiring connector for 40-791 40-1331
HL lever wiring loom 40-1145
D079 Wiring connector for 40-807 40-1392
central wiring loom 40-1166
D079 Wiring connector for 40-1226 40-1365
HL lever wiring loom 40-862
D080 Wiring connector for [LNK] 40-1318
air conditioner
D081 Wiring connector for [LNK] 40-1318
condenser wiring
loom
D082 Wiring connector for 40-807 40-1327
front PTO control so- 40-734
lenoid valve 40-723
40-738
D082 Wiring connector for 40-723 40-1324
front PTO control so- 40-738
lenoid valve 40-734
40-807
D082 Wiring connector for 40-723 40-1281
engine wiring loom 40-738
40-734
D083 Wiring connector for 40-942 40-1317
central wiring loom
D083 Wiring connector for 40-942 40-1392
front lights wiring 40-1076
loom
D086 Wiring connector for [LNK] 40-1285
central wiring loom

40-277
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D087 Wiring connector for [LNK] 40-1285
central wiring loom
F004 04411920.4 Front LH sidelight 40-915 40-1427
and turn indicator 40-964

USA version
Table 175
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D002 Wiring connector for [LNK] 40-1279
central wiring loom
D002 Wiring connector for 40-1120 40-1365
seat wiring loom
D004 Wiring connector for 40-604 40-1306
central wiring loom 40-928
40-953
40-1087
40-1186
40-1206
40-1240
40-843
40-882
40-895
40-743
40-826
40-719
40-728
40-629
40-705
D004 Wiring connector for 40-604 40-1347
rear wiring loom 40-1240
40-1186
40-882
40-928
40-705
40-728
40-826
D004 Wiring connector for 40-629 40-1410
rear wiring loom 40-743
40-719
40-895
40-953
40-1087
40-1206
40-843
D005 Wiring connector for 40-1240 40-1364
central wiring loom
D005 Wiring connector for 40-1243 40-1365
auxiliary distributor 40-1243
control wiring loom
D005 Wiring connector for 40-1240 40-1347
auxiliary distributor
control wiring loom
D006 Wiring connector for 40-613 40-1365
reverse shuttle wir- 40-862
ing loom 40-1262
40-1226

40-278
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D006 Wiring connector for 40-604 40-1347
reverse shuttle wir- 40-1247
ing loom 40-826
40-1186
40-1206
D006 Wiring connector for 40-629 40-1410
reverse shuttle wir- 40-843
ing loom 40-1206
D007 Reverse shuttle 40-1262 40-1365
CAN configuration
connector
D007 Reverse shuttle 40-1262 40-1365
CAN configuration
connector
D009 Wiring connector for 40-928 40-1312
central wiring loom 40-1059
40-1008
40-964
40-992
40-1042
D009 Wiring connector for 40-928 40-1347
front lights wiring 40-964
loom 40-1042
40-992
D009 Wiring connector for 40-964 40-1365
front lights wiring 40-1059
loom 40-1008
D010 Wiring connector for 40-613 40-1365
front wiring loom 40-734
40-710
40-695
40-689
D010 Wiring connector for 40-629 40-1410
engine wiring loom 40-743
40-719
40-843
D010 Wiring connector for 40-604 40-1347
front wiring loom 40-728
40-826
40-683
40-677
40-705
D010 Wiring connector for 40-604 40-1324
central wiring loom 40-743
40-734
40-710
40-695
40-689
40-613
40-843
40-719
40-728
40-705
40-629
40-683
40-677

40-279
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D011 Wiring connector for 40-928 40-1309
central wiring loom 40-1120
40-964
40-1110
40-1137
40-953
D011 Wiring connector for 40-964 40-1365
cowl lights wiring 40-1120
loom 40-1059
40-1008
D011 Wiring connector for 40-928 40-1347
cowl lights wiring 40-992
loom 40-1042
40-1110
D011 Wiring connector for 40-953 40-1410
cowl lights wiring 40-1087
loom 40-1137
D012 Wiring connector for 40-647 40-1311
roof wiring loom 40-660
40-695
40-689
40-657
40-683
40-677
40-652
D012 Wiring connector for 40-677 40-1301
cab power wiring 40-695
loom
D012 Wiring connector for 40-652 40-1318
cab power wiring 40-660
loom
D012 Wiring connector for 40-647 40-1388
cab power wiring 40-689
loom 40-657
40-683
D013 Wiring connector for 40-647 40-1347
power wiring loom 40-1110
40-772
40-992
40-1042
40-683
40-677
40-764
40-769
D013 Wiring connector for 40-657 40-1365
power wiring loom 40-660
40-1120
40-1059
40-1008
40-787
40-783
40-778
40-695
40-689
D013 Wiring connector for [LNK] 40-1410
power wiring loom

40-280
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D013 Wiring connector for 40-647 40-1295
central wiring loom 40-660
40-1120
40-1059
40-1008
40-787
40-783
40-778
40-695
40-689
40-657
40-1110
40-843
40-992
40-1042
40-764
40-769
40-772
40-826
40-652
40-683
40-677
D014 Wiring connector for 40-705 40-1306
engine wiring loom 40-719
40-843
40-882
D014 Wiring connector for 40-710 40-1385
engine wiring loom
D014 Wiring connector for 40-710 40-1425
rear wiring loom 40-719

Table 176
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D015 Wiring connector for 40-843 40-1306
trailer air brake wir- 40-882
ing loom 40-895
D015 Wiring connector for [LNK] 40-1385
trailer air brake wir-
ing loom
D016 Wiring connector for 40-1243 40-1365
rear wiring loom
D016 Wiring connector 40-1243 40-1385
for auxiliary distribu-
tor wiring loom, with
electronic lift
D017 Wiring connector for [LNK] 40-1388
rear wiring loom
D017 Wiring connector for 40-843 40-1306
auxiliary distributor 40-1240
solenoid valves
D018 Wiring connector for 40-728 40-1300
central wiring loom 40-743
40-734
D018 Wiring connector for 40-728 40-1306
PTO sensor wiring 40-843
loom - (USA EX- 40-743
PORT)

40-281
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D018 Wiring connector for 40-734 40-1385
PTO sensor wiring
loom - (USA EX-
PORT)
D019 Wiring connector for 40-843 40-1306
work light and rotat- 40-1087
ing beacon wiring
loom
D019 Wiring connector for 40-1087 40-1292
rear wiring loom
D020 Wiring connector [LNK] 40-1385
D021 Wiring connector for 40-902 40-1385
trailer brake solenoid 40-862
valve
D022 Wiring connector for 40-613 40-1365
rear wiring loom 40-862
40-1269
40-1243
40-1226
40-964
40-902
40-734
40-710
D022 Wiring connector for 40-710 40-1385
central wiring loom 40-862
40-1269
40-1243
40-1226
40-964
40-902
40-734
D023 Wiring connector 40-1269 40-1382
for rear wiring loom,
with electronic lift
D023 Wiring connector for 40-1269 40-1385
electronic lift wiring
loom
D024 Wiring connector 40-1269 40-1382
for rear wiring loom,
with electronic lift
D024 Wiring connector for 40-1269 40-1385
electronic lift wiring
loom
D025 Wiring connector for 40-652 40-1318
heating wiring loom 40-660
D025 Wiring connector for 40-647 40-1388
air conditioner wiring 40-689
loom 40-657
40-683
D025 Wiring connector for 40-647 40-1274
roof wiring loom 40-660
40-657
40-652
D025 Wiring connector for 40-683 40-1275
roof wiring loom 40-689
D026 Wiring connector for 40-683 40-1388
air conditioner wiring 40-689
loom

40-282
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D026 Wiring connector for 40-683 40-1275
roof wiring loom 40-689
D027 Wiring connector for 40-928 40-1312
RH lower front head- 40-1059
light 40-1008
40-964
40-964
40-992
40-1042
D027 Wiring connector for 40-928 40-1427
low front lights wiring 40-1059
loom 40-1008
40-964
40-992
40-1042
D028 Wiring connector for 40-677 40-1301
air conditioner heat 40-695
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1388
air conditioner heat 40-689
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1308
roof wiring loom 40-695
40-689
40-677
D029 Connection between 40-677 40-1301
cab power supply 40-1120
wiring and HV roof 40-1059
40-778
wiring
40-695
40-1042
40-1110
40-764
D029 Wiring connector for 40-677 40-1301
cab power wiring 40-1120
loom 40-1059
40-778
40-695
40-1042
40-1110
40-764
D029 Wiring connector for 40-772 40-1318
cab power wiring 40-992
loom
D029 Wiring connector for 40-683 40-1388
cab power wiring 40-1008
loom 40-689
40-992

40-283
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D029 Wiring connector for 40-683 40-1311
roof wiring loom 40-1120
40-1059
40-1008
40-787
40-783
40-778
40-695
40-689
40-992
40-1042
40-1110
40-677
40-764
40-769
40-772
D030 Wiring connector for 40-683 40-1311
central cab wiring 40-1120
loom 40-1059
40-1008
40-787
40-783
40-778
40-695
40-689
40-772
40-992
40-1042
40-1110
40-677
40-764
40-769
D030 Wiring connector for [LNK] 40-1331
cab power wiring
loom
D030 Wiring connector for 40-683 40-1347
cab power wiring 40-992
loom 40-1042
40-1110
40-677
40-764
40-769
40-772
D030 Wiring connector for [LNK] 40-1410
cab power wiring
loom
D030 Wiring connector for 40-689 40-1365
cab power wiring 40-1120
loom 40-1059
40-1008
40-787
40-783
40-778
40-695
D031 Wiring connector for 40-657 40-1365
roof wiring loom 40-660
40-695
40-689

40-284
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D031 Wiring connector for 40-647 40-1311
central wiring loom 40-660
40-695
40-689
40-657
40-652
40-683
40-677
D031 Wiring connector for 40-647 40-1347
roof wiring loom 40-652
40-683
40-677
40-728

Table 177
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D032 Wiring connector for 40-677 40-1301
cab power wiring 40-695
loom 40-695
D032 Wiring connector for 40-647 40-1311
roof wiring loom 40-660
40-689
40-657
40-652
40-683
40-677
D033 Wiring connector for 40-677 40-1301
roof 40-695
D033 Wiring connector to 40-677 40-1301
wiring loom 40-695
D034 Wiring connector for 40-677 40-1301
roof 40-695
D034 Wiring connector to 40-677 40-1301
wiring loom 40-695
D035 Wiring connector for 40-843 40-1327
central wiring loom
and electronic lift
D037 Wiring connector 40-719 40-1410
40-743
40-1206
40-843
40-1087
D037 Wiring connector for 40-719 40-1410
switch wiring loom 40-743
40-1206
40-843
40-1087
D038 Wiring connector for 40-710 40-1365
RH side console wir- 40-734
ing loom
D038 Wiring connector for 40-710 40-1386
central wiring loom 40-734
and electronic lift

40-285
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D039 Wiring connector for 40-657 40-1365
power wiring loom 40-862
40-660
40-1269
40-1262
40-1243
40-1226
40-1120
40-1059
40-1008
40-964
40-902
40-787
40-783
40-778
40-695
40-689
D039 Wiring connector for 40-647 40-1295
central cab wiring 40-862
loom 40-660
40-1269
40-1262
40-1243
40-1226
40-1120
40-1059
40-1008
40-964
40-902
40-787
40-783
40-778
40-695
40-689
40-657
40-1186
40-1206
40-1240
40-1110
40-1137
40-953
40-992
40-1042
40-1087
40-826
40-843
40-882
40-895
40-928
40-652
40-683
40-677
40-764
40-769
40-772

40-286
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D039 Wiring connector for 40-647 40-1347
power wiring loom 40-1186
40-1042
40-1087
40-1110
40-826
40-882
40-928
40-992
40-652
40-683
40-677
40-764
40-769
40-772
D039 Wiring connector for 40-843 40-1410
power wiring loom 40-1206
40-895
40-953
40-1087
40-1137
D040 Wiring connector for 40-657 40-1365
power wiring loom 40-862
40-660
40-1269
40-1262
40-1243
40-1226
40-1059
40-1008
40-964
40-902
40-787
40-783
40-778
40-734
40-710
40-613
40-695
40-689
D040 Wiring connector for 40-604 40-1347
power wiring loom 40-1247
40-1042
40-1186
40-1240
40-882
40-928
40-992
40-769
40-772
40-826
40-647
40-652
40-683
40-677
40-705
40-728
40-764

40-287
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D040 Wiring connector for 40-629 40-1410
power wiring loom 40-743
40-1087
40-1206
40-843
40-953
D040 Wiring connector for 40-604 40-1295
central wiring loom 40-862
40-660
40-1269
40-1262
40-1243
40-1226
40-1059
40-1008
40-964
40-902
40-783
40-778
40-734
40-710
40-695
40-689
40-657
40-613
40-1186
40-1255
40-1206
40-1240
40-1247
40-1087
40-953
40-992
40-1042
40-882
40-895
40-928
40-772
40-826
40-843
40-769
40-629
40-647
40-652
40-683
40-677
40-705
40-719
40-728
40-743
40-764
D043 Wiring connector 40-728 40-1347
40-826
40-1186
40-1206
D043 Wiring connector for 40-728 40-1347
switch wiring loom 40-826
40-1186
40-1206

40-288
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D044 Wiring connector for 40-764 40-1301
windscreen wiper 40-778
motor wiring loom
D044 Wiring connector for 40-764 40-1279
roof wiring loom 40-778
D045 Wiring connector for 40-772 40-1318
windscreen wiper
wiring loom
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D045 Wiring connector for 40-769 40-1276
roof wiring loom 40-787
40-783
40-772
D046 Wiring connector for 40-772 40-1318
work lights and wind- 40-992
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector for 40-992 40-1388
work lights and wind- 40-1008
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector to 40-769 40-1322
cab roof wiring loom, 40-1008
versions with stan- 40-787
40-783
dard cab
40-772
40-992

40-289
 Wiring diagrams
Table 178
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-769 40-1322
rear screen wiper 40-787
wiring loom, ver- 40-783
40-772
sions without high
visibility cab
D047 Wiring connector for 40-769 40-1300
work lights and wind- 40-787
screen wiper wiring 40-783
40-772
loom, versions with-
out high visibility cab
D050 Wiring connector for 40-928 40-1312
RH lower front head- 40-1059
light 40-1008
40-964
40-992
40-1042
D050 Wiring connector for 40-928 40-1427
low front lights wiring 40-1059
loom 40-1008
40-964
40-992
40-1042
D051 Wiring connector for 40-1042 40-1288
LH lower headlight
wiring loom
D051 2.8059.528.0 Wiring connector for 40-928 40-1427
front lower work light 40-1059
wiring loom, ver- 40-1008
40-964
sions with high vis-
40-992
ibility cab 40-1042
D052 Wiring connector for 40-928 40-1427
low front lights wiring 40-1059
loom 40-1008
40-964
40-992
40-1042
D052 Wiring connector for 40-928 40-1312
LH lower front head- 40-1059
light 40-1008
40-964
40-992
40-1042
D053 2.8059.528.0 Wiring connector for 40-928 40-1427
front lower work light 40-1059
wiring loom, ver- 40-1008
40-964
sions with high vis-
40-992
ibility cab 40-1042
D053 Wiring connector for [LNK] 40-1288
RH lower headlight
wiring loom
D054 Seat configuration 40-862 40-1365
connector
D054a Seat configuration 40-862 40-1365
connector
D054b Seat configuration 40-862 40-1365
connector

40-290
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D055 Seat configuration [LNK] 40-1347
connector
D055a Seat configuration 40-826 40-1347
connector
D055b Seat configuration 40-826 40-1347
connector
D056 Seat configuration 40-843 40-1410
connector
D056a Seat configuration 40-843 40-1410
connector
D056b Seat configuration 40-843 40-1410
connector
D058 Wiring connector 40-826 40-1347
40-882
D058 Wiring connector for 40-826 40-1347
parking brake wiring 40-882
loom
Table 179
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D059 Wiring connector 40-843 40-1410
40-895
D059 Wiring connector for 40-843 40-1410
parking brake wiring 40-895
loom
D060 Wiring connector for 40-902 40-1391
central wiring loom 40-964
D060 Wiring connector for 40-902 40-1365
rear RH work light 40-964
wiring loom
D061 Wiring connector for 40-902 40-1391
central wiring loom 40-964
D061 Wiring connector for 40-902 40-1365
rear LH work light 40-964
wiring loom
D062 Wiring connector for 40-928 40-1427
low front lights wiring 40-1059
loom 40-1008
40-964
40-992
40-1042
D062 Wiring connector for 40-928 40-1312
LH lower front head- 40-1059
light 40-1008
40-964
40-992
40-1042
D063 Wiring connector for 40-1042 40-1301
flashing beacon wir- 40-1059
ing loom
D063 Wiring connector for 40-992 40-1322
flashing beacon wir- 40-1008
ing loom
D063 Wiring connector for 40-992 40-1286
roof wiring loom 40-1059
40-1008
40-1042

40-291
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D064 Wiring connector for 40-1042 40-1301
flashing beacon wir- 40-1059
ing loom
D064 Wiring connector for 40-992 40-1322
flashing beacon wir- 40-1008
ing loom
D064 Wiring connector for 40-992 40-1286
roof wiring loom 40-1059
40-1008
40-1042
D065 Wiring connector for 40-928 40-1285
central wiring loom
D065 Wiring connector for 40-928 40-1347
RH rear lights wiring
loom
D066 Wiring connector for 40-928 40-1285
central wiring loom
D066 Wiring connector for 40-928 40-1347
LH rear lights wiring
loom
D069 Wiring connector for [LNK] 40-1410
roof wiring loom

Table 180
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D070 Wiring connector for [LNK] 40-1410
windscreen washer
pump wiring loom
D071 Wiring connector for [LNK] 40-1410
rear screen washer
pump wiring loom
D075 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
RH front work light 40-1059
D076 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
LH front work light 40-1059
D077 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
LH rear work light 40-1059
D078 2.8039.298.0/20 Wiring connector for 40-1042 40-1301
RH rear work light 40-1059
D079 Wiring connector for [LNK] 40-1423
central wiring loom
D079 Wiring connector for 40-1226 40-1365
HL lever wiring loom 40-862
D079 Wiring connector for 40-826 40-1347
HL lever wiring loom 40-1186
D079 Wiring connector for 40-843 40-1410
HL lever wiring loom 40-1206
D080 Wiring connector for [LNK] 40-1318
air conditioner
D081 Wiring connector for [LNK] 40-1318
condenser wiring
loom

40-292
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D082 Wiring connector for 40-728 40-1327
front PTO control so- 40-743
lenoid valve 40-734
40-743
40-843
D082 Wiring connector for 40-728 40-1324
front PTO control so- 40-743
lenoid valve 40-734
40-843
D082 Wiring connector for 40-728 40-1281
engine wiring loom 40-734
40-743
D083 Wiring connector for 40-953 40-1317
central wiring loom
D083 Wiring connector for 40-953 40-1410
front lights wiring 40-1087
loom
D086 Wiring connector for 40-953 40-1285
central wiring loom
D086 Wiring connector for 40-953 40-1410
rear LH work light
wiring loom, USA
D087 Wiring connector for 40-953 40-1285
central wiring loom
D087 Wiring connector for 40-953 40-1410
rear RH work light
wiring loom
F004 04411920.4 Front LH sidelight 40-928 40-1427
and turn indicator 40-964

40.2.22 - D - Intermediate connections (AGROFARM 410 -> ZKDW470200TD30001)

ITA version
Table 181
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D001 Wiring connector 40-723 40-1331
40-1151
40-799
D001 Wiring connector for 40-723 40-1331
switch wiring loom 40-1151
40-799
D002 Wiring connector for 40-1105 40-1331
seat wiring loom
D003 Wiring connector for 40-799 40-1331
parking brake wiring 40-877
loom
D003 Wiring connector 40-799 40-1331
40-877
D003 Wiring connector for [LNK] [LNK]
parking brake wiring
loom

40-293
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D004 Wiring connector for 40-600 40-1306
central wiring loom 40-889
40-1237
40-1171
40-1151
40-1082
40-948
40-922
40-877
40-852
40-816
40-816
40-701
40-714
40-723
40-738
40-799
40-625
D004 Wiring connector for 40-600 40-1331
rear wiring loom 40-723
40-799
40-877
40-922
40-1151
40-1237
40-701
D004 Wiring connector for 40-625 40-1392
rear wiring loom 40-889
40-948
40-1082
40-1171
40-816
40-714
40-738
D005 Wiring connector for 40-1237 40-1331
auxiliary distributor
control wiring loom
D006 Wiring connector for 40-600 40-1293
central wiring loom 40-1258
40-1250
40-1171
40-625
40-799
40-816
40-1151
D006 Wiring connector for 40-600 40-1331
reverse shuttle wir- 40-799
ing loom 40-1151
40-1250
D008 Seat configuration 40-799 40-1331
connector
D008a Seat configuration 40-799 40-1331
connector
D008b Seat configuration 40-799 40-1331
connector
D009 Wiring connector for 40-922 40-1312
central wiring loom 40-1033
40-984
D009 Wiring connector for 40-922 40-1331
front lights wiring 40-984
loom 40-1033

40-294
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D010 Wiring connector for 40-600 40-1331
engine wiring loom 40-665
40-671
40-701
40-723
D010 Wiring connector for 40-625 40-1392
engine wiring loom 40-714
40-738
40-816
D010 Wiring connector for 40-600 40-1324
central wiring loom 40-723
40-738
40-816
40-701
40-714
40-665
40-671
40-625
D011 Wiring connector for 40-922 40-1289
central wiring loom 40-1105
40-1082
40-1033
40-984
40-948
D011 Wiring connector for 40-922 40-1331
cowl lights wiring 40-1133
loom 40-984
40-1033
40-1105
D011 Wiring connector for 40-948 40-1392
cowl lights wiring 40-1082
loom 40-1133
D012 Wiring connector for 40-637 40-1311
roof wiring loom 40-665
40-671
D012 Wiring connector for 40-671 40-1301
cab power wiring
loom
D012 Wiring connector for 40-637 40-1388
cab power wiring 40-665
loom
D013 Wiring connector for 40-637 40-1331
power wiring loom 40-755
40-984
40-1033
40-1105
40-665
40-671
40-750
D013 Wiring connector for [LNK] 40-1392
power wiring loom
D013 Wiring connector for 40-637 40-1295
central wiring loom 40-1105
40-1033
40-984
40-816
40-755
40-750
40-671
40-665

40-295
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D014 Wiring connector for 40-701 40-1306
engine wiring loom 40-816
40-714
D014 Wiring connector for 40-701 40-1425
rear wiring loom 40-714

Table 182
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D015 Wiring connector for 40-816 40-1306
trailer air brake wir- 40-877
ing loom 40-889
D015 Wiring connector for 40-877 40-1287
rear wiring loom 40-889
D017 Wiring connector for 40-816 40-1306
auxiliary distributor 40-1237
solenoid valves
D018 Wiring connector for 40-816 40-1306
PTO sensor wiring
loom - (USA EX-
PORT)
D019 Wiring connector for 40-1082 40-1306
work light and rotat- 40-816
ing beacon wiring
loom
D019 Wiring connector for [LNK] 40-1292
rear wiring loom
D025 Wiring connector for 40-637 40-1388
air conditioner wiring 40-665
loom
D025 Wiring connector for [LNK] 40-1274
roof wiring loom
D025 Wiring connector for [LNK] 40-1275
roof wiring loom
D026 Wiring connector for 40-665 40-1388
air conditioner wiring
loom
D026 Wiring connector for [LNK] 40-1275
roof wiring loom
D027 Wiring connector for 40-922 40-1312
RH lower front head- 40-1033
light 40-984
D027 Wiring connector for 40-922 40-1427
low front lights wiring 40-984
loom 40-1033
D028 Wiring connector for 40-671 40-1301
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1388
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1308
roof wiring loom 40-671

40-296
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D029 Connection between 40-671 40-1301
cab power supply 40-1105
wiring and HV roof 40-750
40-1033
wiring
D029 Wiring connector for 40-671 40-1301
cab power wiring 40-1105
loom 40-750
40-1033
D029 Wiring connector for 40-665 40-1388
cab power wiring 40-984
loom
D029 Wiring connector for 40-665 40-1311
roof wiring loom 40-1033
40-1105
40-984
40-671
40-750
40-755
D030 Wiring connector for 40-665 40-1311
central cab wiring 40-1033
loom 40-1105
40-984
40-671
40-750
40-755
D030 Wiring connector for 40-665 40-1331
cab power wiring 40-984
loom 40-1033
40-1105
40-671
40-750
40-755
D030 Wiring connector for [LNK] 40-1392
cab power wiring
loom
D031 Wiring connector for 40-637 40-1331
cab power wiring 40-665
loom 40-671
D031 Wiring connector for 40-637 40-1311
central wiring loom 40-665
40-671

40-297
 Wiring diagrams
Table 183
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D032 Wiring connector for 40-671 40-1301
cab power wiring
loom
D032 Wiring connector for 40-637 40-1311
roof wiring loom 40-665
40-671
D033 Wiring connector for 40-671 40-1301
roof
D033 Wiring connector to 40-671 40-1301
wiring loom
D034 Wiring connector for 40-671 40-1301
roof
D034 Wiring connector to 40-671 40-1301
wiring loom
D035 Wiring connector for 40-816 40-1327
central wiring loom
and electronic lift
D036 Wiring connector 40-714 40-1392
40-1082
40-1171
40-816
40-738
D036 Wiring connector for 40-714 40-1392
switch wiring loom 40-1082
40-1171
40-816
40-738
D039 Wiring connector for 40-637 40-1295
central cab wiring 40-1237
loom 40-1171
40-1133
40-1151
40-1082
40-948
40-889
40-922
40-877
40-799
40-1105
40-1033
40-984
40-816
40-755
40-750
40-671
40-665
D039 Wiring connector for 40-637 40-1331
power wiring loom 40-1151
40-1237
40-799
40-877
40-922
40-984
40-1033
40-1105
40-665
40-671
40-750
40-755

40-298
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D039 Wiring connector for 40-816 40-1392
power wiring loom 40-1171
40-948
40-1082
40-1133
40-889
D040 Wiring connector for 40-625 40-1392
power wiring loom 40-948
40-1082
40-1171
40-1258
40-714
40-738
40-816
40-889
D040 Wiring connector for 40-600 40-1331
power wiring loom 40-1033
40-1151
40-1237
40-1250
40-799
40-877
40-922
40-984
40-723
40-750
40-755
40-701
40-637
40-665
40-671
D040 Wiring connector for 40-600 40-1295
central wiring loom 40-1258
40-1250
40-1237
40-1171
40-1151
40-1082
40-1033
40-984
40-799
40-816
40-877
40-889
40-922
40-948
40-637
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-625
D041 Wiring connector for [LNK] 40-1296
rear wiring loom
D042 Wiring connector for 40-1151 40-1293
reverse shuttle wir- 40-1171
ing loom (drivetrain)

40-299
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D042 Wiring connector for 40-1151 40-1296
reverse shuttle wir- 40-1171
ing loom (cab)
D044 Wiring connector for 40-750 40-1301
windscreen wiper
motor wiring loom
D044 Wiring connector for 40-750 40-1279
roof wiring loom
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D046 Wiring connector for 40-984 40-1388
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector to 40-755 40-1322
cab roof wiring loom, 40-984
versions with stan-
dard cab
Table 184
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-755 40-1322
rear screen wiper
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for 40-755 40-1300
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
D048 Wiring connector 40-816 40-1392
40-889
D048 Wiring connector for 40-816 40-1392
parking brake wiring 40-889
loom
D049 Seat configuration 40-816 40-1392
connector
D049a Seat configuration 40-816 40-1392
connector
D049b Seat configuration 40-816 40-1392
connector
D050 Wiring connector for 40-922 40-1312
RH lower front head- 40-1033
light 40-984
D050 Wiring connector for 40-922 40-1427
low front lights wiring 40-984
loom 40-1033
D051 Wiring connector for 40-1033 40-1288
LH lower headlight
wiring loom

40-300
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D051 2.8059.528.0 Wiring connector for 40-922 40-1427
front lower work light 40-984
wiring loom, ver- 40-1033
sions with high vis-
ibility cab
D052 Wiring connector for 40-922 40-1427
low front lights wiring 40-984
loom 40-1033
D052 Wiring connector for 40-922 40-1312
LH lower front head- 40-1033
light 40-984
D053 2.8059.528.0 Wiring connector for 40-922 40-1427
front lower work light 40-984
wiring loom, ver- 40-1033
sions with high vis-
ibility cab
D053 Wiring connector for 40-1033 40-1288
RH lower headlight
wiring loom
Table 185
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D060 Wiring connector for 40-877 40-1331
rear RH work light 40-922
wiring loom
D060 Wiring connector for 40-889 40-1392
rear RH work light 40-948
wiring loom
D061 Wiring connector for 40-877 40-1331
rear LH work light 40-922
wiring loom
D061 Wiring connector for 40-889 40-1392
rear LH work light 40-948
wiring loom
D062 Wiring connector for 40-922 40-1427
low front lights wiring 40-984
loom 40-1033
D062 Wiring connector for 40-922 40-1312
LH lower front head- 40-1033
light 40-984
D063 Wiring connector for 40-1033 40-1301
flashing beacon wir-
ing loom
D063 Wiring connector for 40-984 40-1322
flashing beacon wir-
ing loom
D063 Wiring connector for 40-984 40-1286
roof wiring loom 40-1033
D064 Wiring connector for 40-1033 40-1301
flashing beacon wir-
ing loom
D064 Wiring connector for 40-984 40-1322
flashing beacon wir-
ing loom

40-301
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D064 Wiring connector for 40-984 40-1286
roof wiring loom 40-1033
D067 Wiring connector for [LNK] 40-1392
windscreen washer
pump wiring loom
D068 Wiring connector for [LNK] 40-1392
roof wiring loom
Table 186
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D072 Wiring connector for [LNK] 40-1392
windscreen washer
pump wiring loom
D073 2.8039.160.0 Wiring connector for 40-984 40-1289
front work light wir- 40-1082
ing loom 40-1033
D073 Wiring connector for 40-984 40-1282
front lights and horn 40-1082
wiring loom 40-1033
D074 Wiring connector for 40-984 40-1282
front lights and horn 40-1082
wiring loom 40-1033
D074 2.8039.160.0 Wiring connector for 40-984 40-1289
front work light wir- 40-1082
ing loom 40-1033
D075 Wiring connector for 40-1033 40-1424
roof wiring loom
D075 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
RH front work light
D076 Wiring connector for 40-1033 40-1424
roof wiring loom
D076 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
LH front work light
D077 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
LH rear work light
D078 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
RH rear work light
D079 Wiring connector for 40-799 40-1331
HL lever wiring loom 40-1151
D079 Wiring connector for 40-816 40-1392
central wiring loom 40-1171
D082 Wiring connector for 40-816 40-1327
front PTO control so- 40-723
lenoid valve 40-738
D082 Wiring connector for 40-723 40-1324
front PTO control so- 40-738
lenoid valve 40-816
D082 Wiring connector for 40-723 40-1281
engine wiring loom 40-738
D083 Wiring connector for 40-948 40-1317
central wiring loom
D083 Wiring connector for 40-948 40-1392
front lights wiring 40-1082
loom

40-302
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D084 Wiring connector for 40-1151 40-1296
reverse shuttle sole- 40-1171
noid valve
D085 Wiring connector for 40-1151 40-1296
reverse shuttle sole- 40-1171
noid valve
D086 Wiring connector for [LNK] 40-1285
central wiring loom
D087 Wiring connector for [LNK] 40-1285
central wiring loom
F004 04411920.4 Front LH sidelight 40-922 40-1427
and turn indicator

USA version
Table 187
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D004 Wiring connector for 40-608 40-1306
central wiring loom 40-935
40-959
40-1093
40-1192
40-1211
40-1240
40-852
40-882
40-895
40-743
40-834
40-719
40-728
40-633
40-705
D004 Wiring connector for 40-608 40-1347
rear wiring loom 40-1240
40-1192
40-882
40-935
40-705
40-728
40-834
D004 Wiring connector for 40-633 40-1410
rear wiring loom 40-895
40-959
40-1093
40-1211
40-719
40-743
40-852
D005 Wiring connector for 40-1240 40-1347
auxiliary distributor
control wiring loom
D006 Wiring connector for 40-608 40-1293
central wiring loom 40-1258
40-1250
40-1211
40-633
40-834
40-852
40-1192

40-303
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D006 Wiring connector for 40-608 40-1347
reverse shuttle wir- 40-1250
ing loom 40-834
40-1192
40-1211
D006 Wiring connector for 40-633 40-1410
reverse shuttle wir- 40-852
ing loom 40-1211
D009 Wiring connector for 40-935 40-1312
central wiring loom 40-1001
40-1050
D009 Wiring connector for 40-935 40-1347
front lights wiring 40-1050
loom 40-1001
D010 Wiring connector for 40-633 40-1410
engine wiring loom 40-719
40-743
40-852
D010 Wiring connector for 40-608 40-1347
front wiring loom 40-728
40-834
40-683
40-677
40-705
D010 Wiring connector for 40-608 40-1324
central wiring loom 40-743
40-852
40-719
40-728
40-705
40-633
40-683
40-677
D011 Wiring connector for 40-935 40-1289
central wiring loom 40-1141
40-1115
40-1093
40-1050
40-1001
40-959
D011 Wiring connector for 40-935 40-1347
cowl lights wiring 40-1001
loom 40-1050
40-1115
D011 Wiring connector for 40-959 40-1410
cowl lights wiring 40-1093
loom 40-1141
D012 Wiring connector for 40-647 40-1311
roof wiring loom 40-683
40-677
D012 Wiring connector for 40-677 40-1301
cab power wiring
loom
D012 Wiring connector for 40-647 40-1388
cab power wiring 40-683
loom

40-304
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D013 Wiring connector for 40-647 40-1347
power wiring loom 40-1115
40-1001
40-1050
40-683
40-677
40-764
40-769
D013 Wiring connector for [LNK] 40-1410
power wiring loom
D013 Wiring connector for 40-647 40-1295
central wiring loom 40-1115
40-852
40-1001
40-1050
40-764
40-769
40-834
40-683
40-677
D014 Wiring connector for 40-705 40-1306
engine wiring loom 40-719
40-852
40-882
D014 Wiring connector for [LNK] 40-1425
rear wiring loom

Table 188
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D015 Wiring connector for 40-852 40-1306
trailer air brake wir- 40-882
ing loom 40-895
D017 Wiring connector for 40-852 40-1306
auxiliary distributor 40-1240
solenoid valves
D018 Wiring connector for 40-728 40-1300
central wiring loom 40-743
D018 Wiring connector for 40-728 40-1306
PTO sensor wiring 40-852
loom - (USA EX- 40-743
PORT)
D019 Wiring connector for 40-852 40-1306
work light and rotat- 40-1093
ing beacon wiring
loom
D019 Wiring connector for 40-1093 40-1292
rear wiring loom
D025 Wiring connector for 40-647 40-1388
air conditioner wiring 40-683
loom
D025 Wiring connector for 40-647 40-1274
roof wiring loom
D025 Wiring connector for 40-683 40-1275
roof wiring loom
D026 Wiring connector for 40-683 40-1388
air conditioner wiring
loom

40-305
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D026 Wiring connector for 40-683 40-1275
roof wiring loom
D027 Wiring connector for 40-935 40-1312
RH lower front head- 40-1001
light 40-1050
D027 Wiring connector for 40-935 40-1427
low front lights wiring 40-1001
loom 40-1050
D028 Wiring connector for 40-677 40-1301
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1388
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1308
roof wiring loom 40-677
D029 Connection between 40-677 40-1301
cab power supply 40-1050
wiring and HV roof 40-1115
40-764
wiring
D029 Wiring connector for 40-677 40-1301
cab power wiring 40-1050
loom 40-1115
40-764
D029 Wiring connector for 40-683 40-1388
cab power wiring 40-1001
loom
D029 Wiring connector for 40-683 40-1311
roof wiring loom 40-1001
40-1050
40-1115
40-677
40-764
40-769
D030 Wiring connector for 40-683 40-1311
central cab wiring 40-1001
loom 40-1050
40-1115
40-677
40-764
40-769
D030 Wiring connector for [LNK] 40-1331
cab power wiring
loom
D030 Wiring connector for 40-683 40-1347
cab power wiring 40-1001
loom 40-1050
40-1115
40-677
40-764
40-769
D030 Wiring connector for [LNK] 40-1410
cab power wiring
loom

40-306
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D031 Wiring connector for 40-647 40-1311
central wiring loom 40-683
40-677
D031 Wiring connector for 40-647 40-1347
roof wiring loom 40-683
40-677
40-728
Table 189
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D032 Wiring connector for 40-677 40-1301
cab power wiring
loom
D032 Wiring connector for 40-647 40-1311
roof wiring loom 40-683
40-677
D033 Wiring connector for 40-677 40-1301
roof
D033 Wiring connector to 40-677 40-1301
wiring loom
D034 Wiring connector for 40-677 40-1301
roof
D034 Wiring connector to 40-677 40-1301
wiring loom
D035 Wiring connector for 40-852 40-1327
central wiring loom
and electronic lift
D037 Wiring connector 40-719 40-1410
40-1211
40-743
40-852
40-1093
D037 Wiring connector for 40-719 40-1410
switch wiring loom 40-1211
40-743
40-852
40-1093
D039 Wiring connector for 40-647 40-1295
central cab wiring 40-1192
loom 40-1211
40-1240
40-1115
40-1141
40-959
40-1001
40-1050
40-1093
40-834
40-852
40-882
40-895
40-935
40-683
40-677
40-764
40-769

40-307
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D039 Wiring connector for 40-647 40-1347
power wiring loom 40-1192
40-1050
40-1093
40-1115
40-834
40-882
40-935
40-1001
40-683
40-677
40-764
40-769
D039 Wiring connector for 40-852 40-1410
power wiring loom 40-1211
40-895
40-959
40-1093
40-1141
D040 Wiring connector for 40-608 40-1347
power wiring loom 40-1250
40-1050
40-1192
40-1240
40-882
40-935
40-1001
40-769
40-834
40-647
40-683
40-677
40-705
40-728
40-764
D040 Wiring connector for 40-633 40-1410
power wiring loom 40-1093
40-1211
40-743
40-852
40-959

40-308
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D040 Wiring connector for 40-608 40-1295
central wiring loom 40-1192
40-1258
40-1211
40-1240
40-1250
40-1093
40-959
40-1001
40-1050
40-882
40-895
40-935
40-834
40-852
40-769
40-633
40-647
40-683
40-677
40-705
40-719
40-728
40-743
40-764
D041 Wiring connector for [LNK] 40-1296
rear wiring loom
D042 Wiring connector for 40-1192 40-1293
reverse shuttle wir- 40-1211
ing loom (drivetrain)
D042 Wiring connector for 40-1192 40-1296
reverse shuttle wir- 40-1211
ing loom (cab)
D043 Wiring connector 40-728 40-1347
40-834
40-1192
40-1211
D043 Wiring connector for 40-728 40-1347
switch wiring loom 40-834
40-1192
40-1211
D044 Wiring connector for 40-764 40-1301
windscreen wiper
motor wiring loom
D044 Wiring connector for 40-764 40-1279
roof wiring loom
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D045 Wiring connector for 40-769 40-1276
roof wiring loom
D046 Wiring connector for 40-1001 40-1388
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab

40-309
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D046 Wiring connector to 40-769 40-1322
cab roof wiring loom, 40-1001
versions with stan-
dard cab

Table 190
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-769 40-1322
rear screen wiper
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for 40-769 40-1300
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
D050 Wiring connector for 40-935 40-1312
RH lower front head- 40-1001
light 40-1050
D050 Wiring connector for 40-935 40-1427
low front lights wiring 40-1001
loom 40-1050
D051 Wiring connector for 40-1050 40-1288
LH lower headlight
wiring loom
D051 2.8059.528.0 Wiring connector for 40-935 40-1427
front lower work light 40-1001
wiring loom, ver- 40-1050
sions with high vis-
ibility cab
D052 Wiring connector for 40-935 40-1427
low front lights wiring 40-1001
loom 40-1050
D052 Wiring connector for 40-935 40-1312
LH lower front head- 40-1001
light 40-1050
D053 2.8059.528.0 Wiring connector for 40-935 40-1427
front lower work light 40-1001
wiring loom, ver- 40-1050
sions with high vis-
ibility cab
D053 Wiring connector for [LNK] 40-1288
RH lower headlight
wiring loom
D055 Seat configuration [LNK] 40-1347
connector
D055a Seat configuration 40-834 40-1347
connector
D055b Seat configuration 40-834 40-1347
connector
D056 Seat configuration 40-852 40-1410
connector
D056a Seat configuration 40-852 40-1410
connector

40-310
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D056b Seat configuration 40-852 40-1410
connector
D058 Wiring connector 40-834 40-1347
40-882
D058 Wiring connector for 40-834 40-1347
parking brake wiring 40-882
loom
Table 191
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D059 Wiring connector 40-852 40-1410
40-895
D059 Wiring connector for 40-852 40-1410
parking brake wiring 40-895
loom
D062 Wiring connector for 40-935 40-1427
low front lights wiring 40-1001
loom 40-1050
D062 Wiring connector for 40-935 40-1312
LH lower front head- 40-1001
light 40-1050
D063 Wiring connector for 40-1050 40-1301
flashing beacon wir-
ing loom
D063 Wiring connector for 40-1001 40-1322
flashing beacon wir-
ing loom
D063 Wiring connector for 40-1001 40-1286
roof wiring loom 40-1050
D064 Wiring connector for 40-1050 40-1301
flashing beacon wir-
ing loom
D064 Wiring connector for 40-1001 40-1322
flashing beacon wir-
ing loom
D064 Wiring connector for 40-1001 40-1286
roof wiring loom 40-1050
D065 Wiring connector for 40-935 40-1285
central wiring loom
D065 Wiring connector for 40-935 40-1347
RH rear lights wiring
loom
D066 Wiring connector for 40-935 40-1285
central wiring loom
D066 Wiring connector for 40-935 40-1347
LH rear lights wiring
loom
D069 Wiring connector for [LNK] 40-1410
roof wiring loom
Table 192
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D070 Wiring connector for [LNK] 40-1410
windscreen washer
pump wiring loom

40-311
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D071 Wiring connector for [LNK] 40-1410
rear screen washer
pump wiring loom
D073 2.8039.160.0 Wiring connector for 40-1001 40-1289
front work light wir- 40-1093
ing loom 40-1050
D073 Wiring connector for 40-1001 40-1282
front lights and horn 40-1093
wiring loom 40-1050
D074 Wiring connector for 40-1001 40-1282
front lights and horn 40-1093
wiring loom 40-1050
D074 2.8039.160.0 Wiring connector for 40-1001 40-1289
front work light wir- 40-1093
ing loom 40-1050
D075 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
RH front work light
D076 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
LH front work light
D077 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
LH rear work light
D078 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
RH rear work light
D079 Wiring connector for 40-834 40-1347
HL lever wiring loom 40-1192
D079 Wiring connector for 40-852 40-1410
HL lever wiring loom 40-1211
D082 Wiring connector for 40-728 40-1327
front PTO control so- 40-743
lenoid valve 40-852
D082 Wiring connector for 40-728 40-1324
front PTO control so- 40-743
lenoid valve 40-852
D082 Wiring connector for 40-728 40-1281
engine wiring loom 40-743
D083 Wiring connector for 40-959 40-1317
central wiring loom
D083 Wiring connector for 40-959 40-1410
front lights wiring 40-1093
loom
D084 Wiring connector for 40-1192 40-1296
reverse shuttle sole- 40-1211
noid valve
D085 Wiring connector for 40-1192 40-1296
reverse shuttle sole- 40-1211
noid valve
D086 Wiring connector for 40-959 40-1285
central wiring loom
D086 Wiring connector for 40-959 40-1410
rear LH work light
wiring loom, USA
D087 Wiring connector for 40-959 40-1285
central wiring loom
D087 Wiring connector for 40-959 40-1410
rear RH work light
wiring loom

40-312
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F004 04411920.4 Front LH sidelight 40-935 40-1427
and turn indicator

40.2.23 - D - Intermediate connections (AGROFARM 420 -> ZKDW510200TD30001)

ITA version
Table 193
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D001 Wiring connector 40-723 40-1331
40-1158
40-799
D001 Wiring connector for 40-723 40-1331
switch wiring loom 40-1158
40-799
D002 Wiring connector for 40-1105 40-1331
seat wiring loom
D003 Wiring connector for 40-799 40-1331
parking brake wiring 40-877
loom
D003 Wiring connector 40-799 40-1331
40-877
D003 Wiring connector for [LNK] [LNK]
parking brake wiring
loom
D004 Wiring connector for 40-600 40-1306
central wiring loom 40-889
40-1237
40-1178
40-1158
40-1082
40-948
40-922
40-877
40-852
40-816
40-816
40-701
40-714
40-723
40-738
40-799
40-625
D004 Wiring connector for 40-600 40-1331
rear wiring loom 40-723
40-799
40-877
40-922
40-1158
40-1237
40-701
D004 Wiring connector for 40-625 40-1392
rear wiring loom 40-889
40-948
40-1082
40-1178
40-816
40-714
40-738

40-313
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D005 Wiring connector for 40-1237 40-1331
auxiliary distributor
control wiring loom
D005 Wiring connector for 40-1237 40-1364
central wiring loom
D006 Wiring connector for 40-600 40-1293
central wiring loom 40-1258
40-1250
40-1178
40-625
40-799
40-816
40-1158
D006 Wiring connector for 40-600 40-1331
reverse shuttle wir- 40-799
ing loom 40-1158
40-1250
D008 Seat configuration 40-799 40-1331
connector
D008a Seat configuration 40-799 40-1331
connector
D008b Seat configuration 40-799 40-1331
connector
D009 Wiring connector for 40-922 40-1312
central wiring loom 40-1033
40-984
D009 Wiring connector for 40-922 40-1331
front lights wiring 40-984
loom 40-1033
D010 Wiring connector for 40-600 40-1331
engine wiring loom 40-665
40-671
40-701
40-723
D010 Wiring connector for 40-625 40-1392
engine wiring loom 40-714
40-738
40-816
D010 Wiring connector for 40-600 40-1324
central wiring loom 40-723
40-738
40-816
40-701
40-714
40-665
40-671
40-625
D011 Wiring connector for 40-922 40-1289
central wiring loom 40-1105
40-1082
40-1033
40-984
40-948
D011 Wiring connector for 40-922 40-1331
cowl lights wiring 40-1133
loom 40-984
40-1033
40-1105

40-314
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D011 Wiring connector for 40-948 40-1392
cowl lights wiring 40-1082
loom 40-1133
D012 Wiring connector for 40-637 40-1311
roof wiring loom 40-665
40-671
D012 Wiring connector for 40-671 40-1301
cab power wiring
loom
D012 Wiring connector for 40-637 40-1388
cab power wiring 40-665
loom
D013 Wiring connector for 40-637 40-1331
power wiring loom 40-755
40-984
40-1033
40-1105
40-665
40-671
40-750
D013 Wiring connector for [LNK] 40-1392
power wiring loom
D013 Wiring connector for 40-637 40-1295
central wiring loom 40-1105
40-1033
40-984
40-816
40-755
40-750
40-671
40-665
D014 Wiring connector for 40-701 40-1306
engine wiring loom 40-816
40-714
D014 Wiring connector for 40-701 40-1425
rear wiring loom 40-714

40-315
 Wiring diagrams
Table 194
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D015 Wiring connector for 40-816 40-1306
trailer air brake wir- 40-877
ing loom 40-889
D015 Wiring connector for 40-877 40-1287
rear wiring loom 40-889
D017 Wiring connector for 40-816 40-1306
auxiliary distributor 40-1237
solenoid valves
D017 Wiring connector for 40-1237 40-1388
rear wiring loom
D018 Wiring connector for 40-816 40-1306
PTO sensor wiring
loom - (USA EX-
PORT)
D019 Wiring connector for 40-1082 40-1306
work light and rotat- 40-816
ing beacon wiring
loom
D019 Wiring connector for [LNK] 40-1292
rear wiring loom
D025 Wiring connector for 40-637 40-1388
air conditioner wiring 40-665
loom
D025 Wiring connector for [LNK] 40-1274
roof wiring loom
D025 Wiring connector for [LNK] 40-1275
roof wiring loom
D026 Wiring connector for 40-665 40-1388
air conditioner wiring
loom
D026 Wiring connector for [LNK] 40-1275
roof wiring loom
D027 Wiring connector for 40-922 40-1312
RH lower front head- 40-1033
light 40-984
D027 Wiring connector for 40-922 40-1427
low front lights wiring 40-984
loom 40-1033
D028 Wiring connector for 40-671 40-1301
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1388
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1308
roof wiring loom 40-671
D029 Connection between 40-671 40-1301
cab power supply 40-1105
wiring and HV roof 40-750
40-1033
wiring

40-316
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D029 Wiring connector for 40-671 40-1301
cab power wiring 40-1105
loom 40-750
40-1033
D029 Wiring connector for 40-665 40-1388
cab power wiring 40-984
loom
D029 Wiring connector for 40-665 40-1311
roof wiring loom 40-1033
40-1105
40-984
40-671
40-750
40-755
D030 Wiring connector for 40-665 40-1311
central cab wiring 40-1033
loom 40-1105
40-984
40-671
40-750
40-755
D030 Wiring connector for 40-665 40-1331
cab power wiring 40-984
loom 40-1033
40-1105
40-671
40-750
40-755
D030 Wiring connector for [LNK] 40-1392
cab power wiring
loom
D031 Wiring connector for 40-637 40-1331
cab power wiring 40-665
loom 40-671
D031 Wiring connector for 40-637 40-1311
central wiring loom 40-665
40-671

40-317
 Wiring diagrams
Table 195
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D032 Wiring connector for 40-671 40-1301
cab power wiring
loom
D032 Wiring connector for 40-637 40-1311
roof wiring loom 40-665
40-671
D033 Wiring connector for 40-671 40-1301
roof
D033 Wiring connector to 40-671 40-1301
wiring loom
D034 Wiring connector for 40-671 40-1301
roof
D034 Wiring connector to 40-671 40-1301
wiring loom
D035 Wiring connector for 40-816 40-1327
central wiring loom
and electronic lift
D036 Wiring connector 40-714 40-1392
40-1082
40-1178
40-816
40-738
D036 Wiring connector for 40-714 40-1392
switch wiring loom 40-1082
40-1178
40-816
40-738
D039 Wiring connector for 40-637 40-1295
central cab wiring 40-1237
loom 40-1178
40-1133
40-1158
40-1082
40-948
40-889
40-922
40-877
40-799
40-1105
40-1033
40-984
40-816
40-755
40-750
40-671
40-665
D039 Wiring connector for 40-637 40-1331
power wiring loom 40-1158
40-1237
40-799
40-877
40-922
40-984
40-1033
40-1105
40-665
40-671
40-750
40-755

40-318
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D039 Wiring connector for 40-816 40-1392
power wiring loom 40-1178
40-948
40-1082
40-1133
40-889
D040 Wiring connector for 40-625 40-1392
power wiring loom 40-948
40-1082
40-1178
40-1258
40-714
40-738
40-816
40-889
D040 Wiring connector for 40-600 40-1331
power wiring loom 40-1033
40-1158
40-1237
40-1250
40-799
40-877
40-922
40-984
40-723
40-750
40-755
40-701
40-637
40-665
40-671
D040 Wiring connector for 40-600 40-1295
central wiring loom 40-1258
40-1250
40-1237
40-1178
40-1158
40-1082
40-1033
40-984
40-799
40-816
40-877
40-889
40-922
40-948
40-637
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-625
D041 Wiring connector for [LNK] 40-1296
rear wiring loom
D042 Wiring connector for 40-1158 40-1293
reverse shuttle wir- 40-1178
ing loom (drivetrain)

40-319
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D042 Wiring connector for 40-1158 40-1296
reverse shuttle wir- 40-1178
ing loom (cab)
D044 Wiring connector for 40-750 40-1301
windscreen wiper
motor wiring loom
D044 Wiring connector for 40-750 40-1279
roof wiring loom
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D046 Wiring connector for 40-984 40-1388
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector to 40-755 40-1322
cab roof wiring loom, 40-984
versions with stan-
dard cab
Table 196
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-755 40-1322
rear screen wiper
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for 40-755 40-1300
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
D048 Wiring connector 40-816 40-1392
40-889
D048 Wiring connector for 40-816 40-1392
parking brake wiring 40-889
loom
D049 Seat configuration 40-816 40-1392
connector
D049a Seat configuration 40-816 40-1392
connector
D049b Seat configuration 40-816 40-1392
connector
D050 Wiring connector for 40-922 40-1312
RH lower front head- 40-1033
light 40-984
D050 Wiring connector for 40-922 40-1427
low front lights wiring 40-984
loom 40-1033
D051 Wiring connector for 40-1033 40-1288
LH lower headlight
wiring loom

40-320
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D051 2.8059.528.0 Wiring connector for 40-922 40-1427
front lower work light 40-984
wiring loom, ver- 40-1033
sions with high vis-
ibility cab
D052 Wiring connector for 40-922 40-1427
low front lights wiring 40-984
loom 40-1033
D052 Wiring connector for 40-922 40-1312
LH lower front head- 40-1033
light 40-984
D053 2.8059.528.0 Wiring connector for 40-922 40-1427
front lower work light 40-984
wiring loom, ver- 40-1033
sions with high vis-
ibility cab
D053 Wiring connector for 40-1033 40-1288
RH lower headlight
wiring loom
Table 197
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D060 Wiring connector for 40-877 40-1331
rear RH work light 40-922
wiring loom
D060 Wiring connector for 40-889 40-1392
rear RH work light 40-948
wiring loom
D060 Wiring connector for 40-877 40-1391
central wiring loom 40-942
40-922
D061 Wiring connector for 40-877 40-1391
central wiring loom 40-942
40-922
D061 Wiring connector for 40-877 40-1331
rear LH work light 40-922
wiring loom
D061 Wiring connector for 40-889 40-1392
rear LH work light 40-948
wiring loom
D062 Wiring connector for 40-922 40-1427
low front lights wiring 40-984
loom 40-1033
D062 Wiring connector for 40-922 40-1312
LH lower front head- 40-1033
light 40-984
D063 Wiring connector for 40-1033 40-1301
flashing beacon wir-
ing loom
D063 Wiring connector for 40-984 40-1322
flashing beacon wir-
ing loom
D063 Wiring connector for 40-984 40-1286
roof wiring loom 40-1033

40-321
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D064 Wiring connector for 40-1033 40-1301
flashing beacon wir-
ing loom
D064 Wiring connector for 40-984 40-1322
flashing beacon wir-
ing loom
D064 Wiring connector for 40-984 40-1286
roof wiring loom 40-1033
D067 Wiring connector for [LNK] 40-1392
windscreen washer
pump wiring loom
D068 Wiring connector for [LNK] 40-1392
roof wiring loom
Table 198
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D072 Wiring connector for [LNK] 40-1392
windscreen washer
pump wiring loom
D073 2.8039.160.0 Wiring connector for 40-984 40-1289
front work light wir- 40-1082
ing loom 40-1033
D073 Wiring connector for 40-984 40-1282
front lights and horn 40-1082
wiring loom 40-1033
D074 Wiring connector for 40-984 40-1282
front lights and horn 40-1082
wiring loom 40-1033
D074 2.8039.160.0 Wiring connector for 40-984 40-1289
front work light wir- 40-1082
ing loom 40-1033
D075 Wiring connector for 40-1033 40-1424
roof wiring loom
D075 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
RH front work light
D076 Wiring connector for 40-1033 40-1424
roof wiring loom
D076 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
LH front work light
D077 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
LH rear work light
D078 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
RH rear work light
D079 Wiring connector for 40-799 40-1331
HL lever wiring loom
D082 Wiring connector for 40-816 40-1327
front PTO control so- 40-723
lenoid valve 40-738
D082 Wiring connector for 40-723 40-1324
front PTO control so- 40-738
lenoid valve 40-816
D082 Wiring connector for 40-723 40-1281
engine wiring loom 40-738
D083 Wiring connector for 40-948 40-1317
central wiring loom

40-322
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D083 Wiring connector for 40-948 40-1392
front lights wiring 40-1082
loom
D084 Wiring connector for 40-1158 40-1296
reverse shuttle sole- 40-1178
noid valve
D085 Wiring connector for 40-1158 40-1296
reverse shuttle sole- 40-1178
noid valve
D086 Wiring connector for [LNK] 40-1285
central wiring loom
D087 Wiring connector for [LNK] 40-1285
central wiring loom
F004 04411920.4 Front LH sidelight 40-922 40-1427
and turn indicator
USA version
Table 199
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D004 Wiring connector for 40-608 40-1306
central wiring loom 40-935
40-959
40-1093
40-1199
40-1218
40-1240
40-852
40-882
40-895
40-743
40-834
40-719
40-728
40-633
40-705
D004 Wiring connector for 40-608 40-1347
rear wiring loom 40-1240
40-1199
40-882
40-935
40-705
40-728
40-834
D004 Wiring connector for 40-633 40-1410
rear wiring loom 40-895
40-959
40-1093
40-1218
40-719
40-743
40-852
D005 Wiring connector for 40-1240 40-1347
auxiliary distributor
control wiring loom
D005 Wiring connector for 40-1237 40-1364
central wiring loom

40-323
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D006 Wiring connector for 40-608 40-1293
central wiring loom 40-1258
40-1250
40-1218
40-633
40-834
40-852
40-1199
D006 Wiring connector for 40-608 40-1347
reverse shuttle wir- 40-1250
ing loom 40-834
40-1199
40-1218
D006 Wiring connector for 40-633 40-1410
reverse shuttle wir- 40-852
ing loom 40-1218
D009 Wiring connector for 40-935 40-1312
central wiring loom 40-1001
40-1050
D009 Wiring connector for 40-935 40-1347
front lights wiring 40-1050
loom 40-1001
D010 Wiring connector for 40-633 40-1410
engine wiring loom 40-719
40-743
40-852
D010 Wiring connector for 40-608 40-1347
front wiring loom 40-728
40-834
40-683
40-677
40-705
D010 Wiring connector for 40-608 40-1324
central wiring loom 40-743
40-852
40-719
40-728
40-705
40-633
40-683
40-677
D011 Wiring connector for 40-935 40-1289
central wiring loom 40-1141
40-1115
40-1093
40-1050
40-1001
40-959
D011 Wiring connector for 40-935 40-1347
cowl lights wiring 40-1001
loom 40-1050
40-1115
D011 Wiring connector for 40-959 40-1410
cowl lights wiring 40-1093
loom 40-1141
D012 Wiring connector for 40-647 40-1311
roof wiring loom 40-683
40-677

40-324
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D012 Wiring connector for 40-677 40-1301
cab power wiring
loom
D012 Wiring connector for 40-647 40-1388
cab power wiring 40-683
loom
D013 Wiring connector for 40-647 40-1347
power wiring loom 40-1115
40-1001
40-1050
40-683
40-677
40-764
40-769
D013 Wiring connector for [LNK] 40-1410
power wiring loom
D013 Wiring connector for 40-647 40-1295
central wiring loom 40-1115
40-852
40-1001
40-1050
40-764
40-769
40-834
40-683
40-677
D014 Wiring connector for 40-705 40-1306
engine wiring loom 40-719
40-852
40-882
D014 Wiring connector for [LNK] 40-1425
rear wiring loom

40-325
 Wiring diagrams
Table 200
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D015 Wiring connector for 40-852 40-1306
trailer air brake wir- 40-882
ing loom 40-895
D017 Wiring connector for 40-852 40-1306
auxiliary distributor 40-1240
solenoid valves
D017 Wiring connector for 40-1240 40-1388
rear wiring loom
D018 Wiring connector for 40-728 40-1300
central wiring loom 40-743
D018 Wiring connector for 40-728 40-1306
PTO sensor wiring 40-852
loom - (USA EX- 40-743
PORT)
D019 Wiring connector for 40-852 40-1306
work light and rotat- 40-1093
ing beacon wiring
loom
D019 Wiring connector for 40-1093 40-1292
rear wiring loom
D025 Wiring connector for 40-647 40-1388
air conditioner wiring 40-683
loom
D025 Wiring connector for 40-647 40-1274
roof wiring loom
D025 Wiring connector for 40-683 40-1275
roof wiring loom
D026 Wiring connector for 40-683 40-1388
air conditioner wiring
loom
D026 Wiring connector for 40-683 40-1275
roof wiring loom
D027 Wiring connector for 40-935 40-1312
RH lower front head- 40-1001
light 40-1050
D027 Wiring connector for 40-935 40-1427
low front lights wiring 40-1001
loom 40-1050
D028 Wiring connector for 40-677 40-1301
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1388
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1308
roof wiring loom 40-677
D029 Connection between 40-677 40-1301
cab power supply 40-1050
wiring and HV roof 40-1115
40-764
wiring

40-326
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D029 Wiring connector for 40-677 40-1301
cab power wiring 40-1050
loom 40-1115
40-764
D029 Wiring connector for 40-683 40-1388
cab power wiring 40-1001
loom
D029 Wiring connector for 40-683 40-1311
roof wiring loom 40-1001
40-1050
40-1115
40-677
40-764
40-769
D030 Wiring connector for 40-683 40-1311
central cab wiring 40-1001
loom 40-1050
40-1115
40-677
40-764
40-769
D030 Wiring connector for [LNK] 40-1331
cab power wiring
loom
D030 Wiring connector for 40-683 40-1347
cab power wiring 40-1001
loom 40-1050
40-1115
40-677
40-764
40-769
D030 Wiring connector for [LNK] 40-1410
cab power wiring
loom
D031 Wiring connector for 40-647 40-1311
central wiring loom 40-683
40-677
D031 Wiring connector for 40-647 40-1347
roof wiring loom 40-683
40-677
40-728

40-327
 Wiring diagrams
Table 201
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D032 Wiring connector for 40-677 40-1301
cab power wiring
loom
D032 Wiring connector for 40-647 40-1311
roof wiring loom 40-683
40-677
D033 Wiring connector for 40-677 40-1301
roof
D033 Wiring connector to 40-677 40-1301
wiring loom
D034 Wiring connector for 40-677 40-1301
roof
D034 Wiring connector to 40-677 40-1301
wiring loom
D035 Wiring connector for 40-852 40-1327
central wiring loom
and electronic lift
D037 Wiring connector 40-719 40-1410
40-1218
40-743
40-852
40-1093
D037 Wiring connector for 40-719 40-1410
switch wiring loom 40-1218
40-743
40-852
40-1093
D039 Wiring connector for 40-647 40-1295
central cab wiring 40-1199
loom 40-1218
40-1240
40-1115
40-1141
40-959
40-1001
40-1050
40-1093
40-834
40-852
40-882
40-895
40-935
40-683
40-677
40-764
40-769
D039 Wiring connector for 40-647 40-1347
power wiring loom 40-1199
40-1050
40-1093
40-1115
40-834
40-882
40-935
40-1001
40-683
40-677
40-764
40-769

40-328
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D039 Wiring connector for 40-852 40-1410
power wiring loom 40-1218
40-895
40-959
40-1093
40-1141
D040 Wiring connector for 40-608 40-1347
power wiring loom 40-1250
40-1050
40-1199
40-1240
40-882
40-935
40-1001
40-769
40-834
40-647
40-683
40-677
40-705
40-728
40-764
D040 Wiring connector for 40-633 40-1410
power wiring loom 40-1093
40-1218
40-743
40-852
40-959
D040 Wiring connector for 40-608 40-1295
central wiring loom 40-1199
40-1258
40-1218
40-1240
40-1250
40-1093
40-959
40-1001
40-1050
40-882
40-895
40-935
40-834
40-852
40-769
40-633
40-647
40-683
40-677
40-705
40-719
40-728
40-743
40-764
D041 Wiring connector for [LNK] 40-1296
rear wiring loom
D042 Wiring connector for 40-1199 40-1293
reverse shuttle wir- 40-1218
ing loom (drivetrain)
D042 Wiring connector for 40-1199 40-1296
reverse shuttle wir- 40-1218
ing loom (cab)

40-329
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D043 Wiring connector 40-728 40-1347
40-834
40-1199
40-1218
D043 Wiring connector for 40-728 40-1347
switch wiring loom 40-834
40-1199
40-1218
D044 Wiring connector for 40-764 40-1301
windscreen wiper
motor wiring loom
D044 Wiring connector for 40-764 40-1279
roof wiring loom
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D045 Wiring connector for 40-769 40-1276
roof wiring loom
D046 Wiring connector for 40-1001 40-1388
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector to 40-769 40-1322
cab roof wiring loom, 40-1001
versions with stan-
dard cab

Table 202
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-769 40-1322
rear screen wiper
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for 40-769 40-1300
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
D050 Wiring connector for 40-935 40-1312
RH lower front head- 40-1001
light 40-1050
D050 Wiring connector for 40-935 40-1427
low front lights wiring 40-1001
loom 40-1050
D051 Wiring connector for 40-1050 40-1288
LH lower headlight
wiring loom
D051 2.8059.528.0 Wiring connector for 40-935 40-1427
front lower work light 40-1001
wiring loom, ver- 40-1050
sions with high vis-
ibility cab

40-330
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D052 Wiring connector for 40-935 40-1427
low front lights wiring 40-1001
loom 40-1050
D052 Wiring connector for 40-935 40-1312
LH lower front head- 40-1001
light 40-1050
D053 2.8059.528.0 Wiring connector for 40-935 40-1427
front lower work light 40-1001
wiring loom, ver- 40-1050
sions with high vis-
ibility cab
D053 Wiring connector for [LNK] 40-1288
RH lower headlight
wiring loom
D055 Seat configuration [LNK] 40-1347
connector
D055a Seat configuration 40-834 40-1347
connector
D055b Seat configuration 40-834 40-1347
connector
D056 Seat configuration 40-852 40-1410
connector
D056a Seat configuration 40-852 40-1410
connector
D056b Seat configuration 40-852 40-1410
connector
D058 Wiring connector 40-834 40-1347
40-882
D058 Wiring connector for 40-834 40-1347
parking brake wiring 40-882
loom

40-331
 Wiring diagrams
Table 203
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D059 Wiring connector 40-852 40-1410
40-895
D059 Wiring connector for 40-852 40-1410
parking brake wiring 40-895
loom
D062 Wiring connector for 40-935 40-1427
low front lights wiring 40-1001
loom 40-1050
D062 Wiring connector for 40-935 40-1312
LH lower front head- 40-1001
light 40-1050
D063 Wiring connector for 40-1050 40-1301
flashing beacon wir-
ing loom
D063 Wiring connector for 40-1001 40-1322
flashing beacon wir-
ing loom
D063 Wiring connector for 40-1001 40-1286
roof wiring loom 40-1050
D064 Wiring connector for 40-1050 40-1301
flashing beacon wir-
ing loom
D064 Wiring connector for 40-1001 40-1322
flashing beacon wir-
ing loom
D064 Wiring connector for 40-1001 40-1286
roof wiring loom 40-1050
D065 Wiring connector for 40-935 40-1285
central wiring loom
D065 Wiring connector for 40-935 40-1347
RH rear lights wiring
loom
D066 Wiring connector for 40-935 40-1285
central wiring loom
D066 Wiring connector for 40-935 40-1347
LH rear lights wiring
loom
D069 Wiring connector for [LNK] 40-1410
roof wiring loom
Table 204
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D070 Wiring connector for [LNK] 40-1410
windscreen washer
pump wiring loom
D071 Wiring connector for [LNK] 40-1410
rear screen washer
pump wiring loom
D073 2.8039.160.0 Wiring connector for 40-1001 40-1289
front work light wir- 40-1093
ing loom 40-1050
D073 Wiring connector for 40-1001 40-1282
front lights and horn 40-1093
wiring loom 40-1050

40-332
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D074 Wiring connector for 40-1001 40-1282
front lights and horn 40-1093
wiring loom 40-1050
D074 2.8039.160.0 Wiring connector for 40-1001 40-1289
front work light wir- 40-1093
ing loom 40-1050
D075 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
RH front work light
D076 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
LH front work light
D077 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
LH rear work light
D078 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
RH rear work light
D079 Wiring connector for 40-834 40-1347
HL lever wiring loom 40-1199
D079 Wiring connector for 40-852 40-1410
HL lever wiring loom 40-1218
D082 Wiring connector for 40-728 40-1327
front PTO control so- 40-743
lenoid valve 40-852
D082 Wiring connector for 40-728 40-1324
front PTO control so- 40-743
lenoid valve 40-852
D082 Wiring connector for 40-728 40-1281
engine wiring loom 40-743
D083 Wiring connector for 40-959 40-1317
central wiring loom
D083 Wiring connector for 40-959 40-1410
front lights wiring 40-1093
loom
D084 Wiring connector for 40-1199 40-1296
reverse shuttle sole- 40-1218
noid valve
D085 Wiring connector for 40-1199 40-1296
reverse shuttle sole- 40-1218
noid valve
D086 Wiring connector for 40-959 40-1285
central wiring loom
D086 Wiring connector for 40-959 40-1410
rear LH work light
wiring loom, USA
D087 Wiring connector for 40-959 40-1285
central wiring loom
D087 Wiring connector for 40-959 40-1410
rear RH work light
wiring loom
F004 04411920.4 Front LH sidelight 40-935 40-1427
and turn indicator

40-333
 Wiring diagrams
40.2.24 - D - Intermediate connections (AGROFARM 430 -> ZKDW550200TD30001)
ITA version
Table 205
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D001 Wiring connector 40-723 40-1331
40-1158
40-799
D001 Wiring connector for 40-723 40-1331
switch wiring loom 40-1158
40-799
D002 Wiring connector for 40-1105 40-1331
seat wiring loom
D002 Wiring connector for 40-1125 40-1365
seat wiring loom
D002 Wiring connector for 40-1105 40-1279
central wiring loom
D003 Wiring connector for 40-799 40-1331
parking brake wiring 40-877
loom
D003 Wiring connector 40-799 40-1331
40-877
D003 Wiring connector for [LNK] [LNK]
parking brake wiring
loom
D004 Wiring connector for 40-600 40-1306
central wiring loom 40-1237
40-1158
40-922
40-877
40-701
40-714
40-723
40-738
40-799
D004 Wiring connector for 40-600 40-1331
rear wiring loom 40-723
40-799
40-877
40-922
40-1158
40-1237
40-701
D005 Wiring connector for 40-1237 40-1364
central wiring loom 40-1243
D005 Wiring connector for 40-1237 40-1331
auxiliary distributor
control wiring loom
D005 Wiring connector for 40-1243 40-1365
auxiliary distributor
control wiring loom

40-334
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D006 Wiring connector for 40-616 40-1293
central wiring loom 40-1266
40-1250
40-1231
40-1231
40-1158
40-870
40-799
40-834
40-600
D006 Wiring connector for 40-600 40-1331
reverse shuttle wir- 40-799
ing loom 40-1158
40-1250
D006 Wiring connector for 40-616 40-1365
reverse shuttle wir- 40-870
ing loom 40-1266
40-1231
D007 Reverse shuttle 40-1266 40-1365
CAN configuration
connector
D007 Reverse shuttle 40-1266 40-1365
CAN configuration
connector
D008 Seat configuration 40-799 40-1331
connector
D008a Seat configuration 40-799 40-1331
connector
D008b Seat configuration 40-799 40-1331
connector
D009 Wiring connector for 40-922 40-1312
central wiring loom 40-1067
40-1016
40-970
40-1033
40-984
D009 Wiring connector for 40-922 40-1331
front lights wiring 40-984
loom 40-1033
D009 Wiring connector for 40-970 40-1365
front lights wiring 40-1067
loom 40-1016
D010 Wiring connector for 40-600 40-1331
engine wiring loom 40-665
40-671
40-701
40-723
D010 Wiring connector for 40-616 40-1365
front wiring loom 40-734
40-710
40-695
40-689

40-335
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D010 Wiring connector for 40-600 40-1324
central wiring loom 40-738
40-734
40-710
40-695
40-689
40-616
40-723
40-701
40-714
40-665
40-671
D011 Wiring connector for 40-922 40-1289
central wiring loom 40-1125
40-1105
40-1067
40-1050
40-1033
40-1016
40-1001
40-984
40-970
40-935
D011 Wiring connector for 40-922 40-1331
cowl lights wiring 40-984
loom 40-1033
40-1105
D011 Wiring connector for 40-970 40-1365
cowl lights wiring 40-1125
loom 40-1067
40-1016
D012 Wiring connector for 40-637 40-1311
roof wiring loom 40-695
40-689
40-657
40-665
40-671
D012 Wiring connector for 40-671 40-1301
cab power wiring 40-695
loom
D012 Wiring connector for 40-637 40-1388
cab power wiring 40-689
loom 40-657
40-665
D013 Wiring connector for 40-637 40-1331
power wiring loom 40-755
40-984
40-1033
40-1105
40-665
40-671
40-750
D013 Wiring connector for 40-657 40-1365
power wiring loom 40-1125
40-1067
40-1016
40-783
40-778
40-695
40-689

40-336
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D013 Wiring connector for 40-637 40-1295
central wiring loom 40-1125
40-1067
40-1016
40-783
40-778
40-695
40-689
40-657
40-1105
40-1033
40-984
40-755
40-750
40-671
40-665
D014 Wiring connector for 40-701 40-1306
engine wiring loom 40-714
D014 Wiring connector for 40-710 40-1385
engine wiring loom
D014 Wiring connector for 40-701 40-1425
rear wiring loom 40-710
40-714
Table 206
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D015 Wiring connector for 40-877 40-1306
trailer air brake wir-
ing loom
D015 Wiring connector for [LNK] 40-1385
trailer air brake wir-
ing loom
D015 Wiring connector for 40-877 40-1287
rear wiring loom
D016 Wiring connector 40-1243 40-1385
for auxiliary distribu-
tor wiring loom, with
electronic lift
D016 Wiring connector for 40-1243 40-1365
rear wiring loom
D017 Wiring connector for 40-1237 40-1388
rear wiring loom
D017 Wiring connector for 40-1237 40-1306
auxiliary distributor
solenoid valves
D018 Wiring connector for [LNK] 40-1306
PTO sensor wiring
loom - (USA EX-
PORT)
D018 Wiring connector for 40-734 40-1385
PTO sensor wiring
loom - (USA EX-
PORT)
D019 Wiring connector for [LNK] 40-1306
work light and rotat-
ing beacon wiring
loom

40-337
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D020 Wiring connector [LNK] 40-1385
D021 Wiring connector for 40-902 40-1385
trailer brake solenoid 40-870
valve
D021 Wiring connector for 40-870 40-1324
rear wiring loom
D022 Wiring connector for 40-710 40-1385
central wiring loom 40-870
40-1269
40-1243
40-1231
40-902
40-734
D022 Wiring connector for 40-616 40-1365
rear wiring loom 40-870
40-1269
40-1243
40-1231
40-970
40-902
40-734
40-710
D023 Wiring connector 40-1269 40-1382
for rear wiring loom,
with electronic lift
D023 Wiring connector for 40-1269 40-1385
electronic lift wiring
loom
D024 Wiring connector 40-1269 40-1382
for rear wiring loom,
with electronic lift
D024 Wiring connector for 40-1269 40-1385
electronic lift wiring
loom
D025 Wiring connector for 40-637 40-1388
air conditioner wiring 40-689
loom 40-657
40-665
D025 Wiring connector for 40-657 40-1274
roof wiring loom
D025 Wiring connector for 40-689 40-1275
roof wiring loom
D026 Wiring connector for 40-665 40-1388
air conditioner wiring 40-689
loom
D026 Wiring connector for 40-689 40-1275
roof wiring loom
D027 Wiring connector for 40-922 40-1312
RH lower front head- 40-1067
light 40-1016
40-970
40-1033
40-984
D027 Wiring connector for 40-922 40-1427
low front lights wiring 40-1067
loom 40-1016
40-970
40-984
40-1033

40-338
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D028 Wiring connector for 40-671 40-1301
air conditioner heat 40-695
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1388
air conditioner heat 40-689
exchanger fan wiring
loom
D028 Wiring connector for 40-665 40-1308
roof wiring loom 40-695
40-689
40-671
D029 Connection between 40-671 40-1301
cab power supply 40-1125
wiring and HV roof 40-1067
40-778
wiring
40-695
40-1105
40-750
40-1033
D029 Wiring connector for 40-671 40-1301
cab power wiring 40-1125
loom 40-1067
40-778
40-695
40-1105
40-750
40-1033
D029 Wiring connector for 40-665 40-1388
cab power wiring 40-1016
loom 40-689
40-984
D029 Wiring connector for 40-665 40-1311
roof wiring loom 40-1125
40-1067
40-1016
40-783
40-778
40-695
40-689
40-1033
40-1105
40-984
40-671
40-750
40-755
D030 Wiring connector for 40-665 40-1311
central cab wiring 40-1125
loom 40-1067
40-1016
40-783
40-778
40-695
40-689
40-1033
40-1105
40-984
40-671
40-750
40-755

40-339
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D030 Wiring connector for 40-665 40-1331
cab power wiring 40-984
loom 40-1033
40-1105
40-671
40-750
40-755
D030 Wiring connector for 40-689 40-1365
cab power wiring 40-1125
loom 40-1067
40-1016
40-783
40-778
40-695
D031 Wiring connector for 40-637 40-1331
cab power wiring 40-665
loom 40-671
D031 Wiring connector for 40-657 40-1365
roof wiring loom 40-695
40-689
D031 Wiring connector for 40-637 40-1311
central wiring loom 40-695
40-689
40-657
40-665
40-671

Table 207
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D032 Wiring connector for 40-671 40-1301
cab power wiring 40-695
loom
D032 Wiring connector for 40-637 40-1311
roof wiring loom 40-695
40-689
40-657
40-665
40-671
D033 Wiring connector for 40-671 40-1301
roof 40-695
D033 Wiring connector to 40-671 40-1301
wiring loom 40-695
D034 Wiring connector for 40-671 40-1301
roof 40-695
D034 Wiring connector to 40-671 40-1301
wiring loom 40-695
D035 Wiring connector for [LNK] 40-1327
central wiring loom
and electronic lift
D038 Wiring connector for 40-710 40-1386
central wiring loom 40-734
and electronic lift
D038 Wiring connector for 40-710 40-1365
RH side console wir- 40-734
ing loom

40-340
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D039 Wiring connector for 40-637 40-1295
central cab wiring 40-870
loom 40-1269
40-1266
40-1243
40-1231
40-1125
40-1067
40-1016
40-970
40-902
40-783
40-778
40-695
40-689
40-657
40-1237
40-1130
40-1158
40-922
40-877
40-799
40-1105
40-1033
40-984
40-755
40-750
40-671
40-665
D039 Wiring connector for 40-637 40-1331
power wiring loom 40-1158
40-1237
40-799
40-877
40-922
40-984
40-1033
40-1105
40-665
40-671
40-750
40-755
D039 Wiring connector for 40-657 40-1365
power wiring loom 40-870
40-1269
40-1266
40-1243
40-1231
40-1125
40-1067
40-1016
40-970
40-902
40-783
40-778
40-695
40-689

40-341
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D040 Wiring connector for 40-616 40-1365
power wiring loom 40-870
40-1269
40-1266
40-1243
40-1231
40-1067
40-1016
40-970
40-902
40-783
40-778
40-734
40-710
40-695
40-689
40-657
D040 Wiring connector for 40-600 40-1331
power wiring loom 40-1033
40-1158
40-1237
40-1250
40-799
40-877
40-922
40-984
40-723
40-750
40-755
40-701
40-637
40-665
40-671

40-342
Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D040 Wiring connector for 40-600 40-1295
central wiring loom 40-870
40-1269
40-1266
40-1243
40-1231
40-1067
40-1016
40-970
40-902
40-783
40-778
40-734
40-714
40-710
40-695
40-689
40-657
40-616
40-1250
40-1237
40-1158
40-1033
40-984
40-799
40-877
40-922
40-637
40-665
40-671
40-701
40-723
40-738
40-750
40-755
D041 Wiring connector for [LNK] 40-1296
rear wiring loom
D042 Wiring connector for 40-1158 40-1293
reverse shuttle wir-
ing loom (drivetrain)
D042 Wiring connector for 40-1158 40-1296
reverse shuttle wir-
ing loom (cab)
D044 Wiring connector for 40-750 40-1301
windscreen wiper 40-778
motor wiring loom
D044 Wiring connector for 40-750 40-1279
roof wiring loom 40-778
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D045 Wiring connector for 40-783 40-1276
roof wiring loom
D046 Wiring connector for 40-984 40-1388
work lights and wind- 40-1016
screen wiper wiring
loom, versions with-
out high visibility cab

40-343
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D046 Wiring connector to 40-755 40-1322
cab roof wiring loom, 40-1016
versions with stan- 40-783
40-984
dard cab

Table 208
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-755 40-1322
rear screen wiper 40-783
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for 40-783 40-1300
work lights and wind- 40-755
screen wiper wiring
loom, versions with-
out high visibility cab
D050 Wiring connector for 40-922 40-1312
RH lower front head- 40-1067
light 40-1016
40-970
40-1033
40-984
D050 Wiring connector for 40-922 40-1427
low front lights wiring 40-1067
loom 40-1016
40-970
40-984
40-1033
D051 Wiring connector for 40-1033 40-1288
LH lower headlight
wiring loom
D051 2.8059.528.0 Wiring connector for 40-922 40-1427
front lower work light 40-1067
wiring loom, ver- 40-1016
40-970
sions with high vis-
40-984
ibility cab 40-1033
D052 Wiring connector for 40-922 40-1427
low front lights wiring 40-1067
loom 40-1016
40-970
40-984
40-1033
D052 Wiring connector for 40-922 40-1312
LH lower front head- 40-1067
light 40-1016
40-970
40-1033
40-984
D053 2.8059.528.0 Wiring connector for 40-922 40-1427
front lower work light 40-1067
wiring loom, ver- 40-1016
40-970
sions with high vis-
40-984
ibility cab 40-1033

40-344
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D053 Wiring connector for 40-1033 40-1288
RH lower headlight
wiring loom
D054 Seat configuration 40-870 40-1365
connector
D054a Seat configuration 40-870 40-1365
connector
D054b Seat configuration 40-870 40-1365
connector
D057 Wiring connector for 40-902 40-1365
parking brake wiring 40-870
loom
D057 Wiring connector 40-902 40-1365
40-870
Table 209
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D060 Wiring connector for 40-877 40-1391
central wiring loom 40-970
40-902
40-922
D060 Wiring connector for 40-877 40-1331
rear RH work light 40-922
wiring loom
D060 Wiring connector for 40-902 40-1365
rear RH work light 40-970
wiring loom
D061 Wiring connector for 40-902 40-1391
central wiring loom 40-970
D061 Wiring connector for 40-877 40-1331
rear LH work light 40-922
wiring loom
D061 Wiring connector for 40-902 40-1365
rear LH work light 40-970
wiring loom
D062 Wiring connector for 40-922 40-1427
low front lights wiring 40-1067
loom 40-1016
40-970
40-984
40-1033
D062 Wiring connector for 40-922 40-1312
LH lower front head- 40-1067
light 40-1016
40-970
40-1033
40-984
D063 Wiring connector for 40-1033 40-1301
flashing beacon wir- 40-1067
ing loom
D063 Wiring connector for 40-984 40-1322
flashing beacon wir- 40-1016
ing loom
D063 Wiring connector for 40-984 40-1286
roof wiring loom 40-1067
40-1016
40-1033

40-345
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ [LNK] Link to wiring
NOTES loom
D064 Wiring connector for 40-1033 40-1301
flashing beacon wir- 40-1067
ing loom
D064 Wiring connector for 40-984 40-1322
flashing beacon wir- 40-1016
ing loom
D064 Wiring connector for 40-984 40-1286
roof wiring loom 40-1067
40-1016
40-1033
Table 210
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D073 2.8039.160.0 Wiring connector for 40-984 40-1289
front work light wir- 40-1067
ing loom 40-1050
40-1033
40-1016
40-1001
D073 Wiring connector for 40-984 40-1282
front lights and horn 40-1067
wiring loom 40-1050
40-1033
40-1016
40-1001
D074 Wiring connector for 40-984 40-1282
front lights and horn 40-1067
wiring loom 40-1050
40-1033
40-1016
40-1001
D074 2.8039.160.0 Wiring connector for 40-984 40-1289
front work light wir- 40-1067
ing loom 40-1050
40-1033
40-1016
40-1001
D075 Wiring connector for 40-1033 40-1424
roof wiring loom 40-1067
D075 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
RH front work light 40-1067
D076 Wiring connector for 40-1033 40-1424
roof wiring loom 40-1067
D076 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
LH front work light 40-1067
D077 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
LH rear work light 40-1067
D078 2.8039.298.0/20 Wiring connector for 40-1033 40-1301
RH rear work light 40-1067
D079 Wiring connector for 40-799 40-1331
HL lever wiring loom 40-1158
D079 Wiring connector for 40-1231 40-1365
HL lever wiring loom 40-870
D082 Wiring connector for 40-734 40-1327
front PTO control so- 40-723
lenoid valve 40-738

40-346
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D082 Wiring connector for 40-723 40-1324
front PTO control so- 40-738
lenoid valve 40-734
D082 Wiring connector for 40-723 40-1281
engine wiring loom 40-738
40-734
D084 Wiring connector for 40-1158 40-1295
hydraulic reverse
shuttle wiring loom
on drivetrain
D084 Wiring connector for 40-1231 40-1296
reverse shuttle sole-
noid valve
D085 Wiring connector for 40-1158 40-1295
hydraulic reverse
shuttle wiring loom
on drivetrain
D085 Wiring connector for 40-1231 40-1296
reverse shuttle sole-
noid valve
F004 04411920.4 Front LH sidelight 40-922 40-1427
and turn indicator 40-970

USA version
Table 211
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D002 Wiring connector for [LNK] 40-1279
central wiring loom
D002 Wiring connector for 40-1125 40-1365
seat wiring loom
D004 Wiring connector for 40-608 40-1306
central wiring loom 40-935
40-1199
40-1240
40-882
40-834
40-728
40-705
D004 Wiring connector for 40-608 40-1347
rear wiring loom 40-1240
40-1199
40-882
40-935
40-705
40-728
40-834
D005 Wiring connector for 40-1240 40-1364
central wiring loom
D005 Wiring connector for 40-1243 40-1365
auxiliary distributor 40-1243
control wiring loom
D005 Wiring connector for 40-1240 40-1347
auxiliary distributor
control wiring loom

40-347
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D006 Wiring connector for 40-616 40-1365
reverse shuttle wir- 40-870
ing loom 40-1266
40-1231
D006 Wiring connector for 40-616 40-1293
central wiring loom 40-1266
40-1250
40-1231
40-1199
40-870
40-608
D006 Wiring connector for 40-608 40-1347
reverse shuttle wir- 40-1250
ing loom 40-834
40-1199
D007 Reverse shuttle 40-1266 40-1365
CAN configuration
connector
D007 Reverse shuttle 40-1266 40-1365
CAN configuration
connector
D009 Wiring connector for 40-935 40-1312
central wiring loom 40-1067
40-1016
40-970
40-1001
40-1050
D009 Wiring connector for 40-935 40-1347
front lights wiring 40-970
loom 40-1050
40-1001
D009 Wiring connector for 40-970 40-1365
front lights wiring 40-1067
loom 40-1016
D010 Wiring connector for 40-616 40-1365
front wiring loom 40-734
40-710
40-695
40-689
D010 Wiring connector for 40-608 40-1347
front wiring loom 40-728
40-834
40-683
40-677
40-705
D010 Wiring connector for 40-608 40-1324
central wiring loom 40-734
40-710
40-695
40-689
40-616
40-728
40-705
40-683
40-677

40-348
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D011 Wiring connector for 40-922 40-1289
central wiring loom 40-1141
40-1125
40-1115
40-1067
40-1050
40-1033
40-1016
40-1001
40-984
40-970
40-935
D011 Wiring connector for 40-970 40-1365
cowl lights wiring 40-1125
loom 40-1067
40-1016
D011 Wiring connector for 40-935 40-1347
cowl lights wiring 40-1001
loom 40-1050
40-1115
D012 Wiring connector for 40-647 40-1311
roof wiring loom 40-695
40-689
40-657
40-683
40-677
D012 Wiring connector for 40-677 40-1301
cab power wiring 40-695
loom
D012 Wiring connector for 40-647 40-1388
cab power wiring 40-689
loom 40-657
40-683
D013 Wiring connector for 40-647 40-1347
power wiring loom 40-1115
40-1001
40-1050
40-683
40-677
40-764
40-769
D013 Wiring connector for 40-657 40-1365
power wiring loom 40-1125
40-1067
40-1016
40-783
40-778
40-695
40-689

40-349
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D013 Wiring connector for 40-647 40-1295
central wiring loom 40-1125
40-1067
40-1016
40-783
40-778
40-695
40-689
40-657
40-1115
40-1001
40-1050
40-764
40-769
40-834
40-683
40-677
D014 Wiring connector for 40-705 40-1306
engine wiring loom 40-882
D014 Wiring connector for 40-710 40-1385
engine wiring loom
D014 Wiring connector for 40-710 40-1425
rear wiring loom
Table 212
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D015 Wiring connector for [LNK] 40-1306
trailer air brake wir- 40-882
ing loom
D015 Wiring connector for [LNK] 40-1385
trailer air brake wir-
ing loom
D016 Wiring connector for 40-1243 40-1365
rear wiring loom
D016 Wiring connector 40-1243 40-1385
for auxiliary distribu-
tor wiring loom, with
electronic lift
D017 Wiring connector for [LNK] 40-1388
rear wiring loom
D017 Wiring connector for 40-1240 40-1306
auxiliary distributor
solenoid valves
D018 Wiring connector for 40-728 40-1300
central wiring loom 40-734
D018 Wiring connector for 40-728 40-1306
PTO sensor wiring
loom - (USA EX-
PORT)
D018 Wiring connector for 40-734 40-1385
PTO sensor wiring
loom - (USA EX-
PORT)
D019 Wiring connector for [LNK] 40-1306
work light and rotat-
ing beacon wiring
loom

40-350
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D020 Wiring connector [LNK] 40-1385
D021 Wiring connector for 40-902 40-1385
trailer brake solenoid 40-870
valve
D022 Wiring connector for 40-616 40-1365
rear wiring loom 40-870
40-1269
40-1243
40-1231
40-970
40-902
40-734
40-710
D022 Wiring connector for 40-710 40-1385
central wiring loom 40-870
40-1269
40-1243
40-1231
40-970
40-902
40-734
D023 Wiring connector 40-1269 40-1382
for rear wiring loom,
with electronic lift
D023 Wiring connector for 40-1269 40-1385
electronic lift wiring
loom
D024 Wiring connector 40-1269 40-1382
for rear wiring loom,
with electronic lift
D024 Wiring connector for 40-1269 40-1385
electronic lift wiring
loom
D025 Wiring connector for 40-647 40-1388
air conditioner wiring 40-689
loom 40-657
40-683
D025 Wiring connector for 40-647 40-1274
roof wiring loom 40-657
D025 Wiring connector for 40-683 40-1275
roof wiring loom 40-689
D026 Wiring connector for 40-683 40-1388
air conditioner wiring 40-689
loom
D026 Wiring connector for 40-683 40-1275
roof wiring loom 40-689
D027 Wiring connector for 40-935 40-1312
RH lower front head- 40-1067
light 40-1016
40-970
40-970
40-1001
40-1050
D027 Wiring connector for 40-935 40-1427
low front lights wiring 40-1067
loom 40-1016
40-970
40-1001
40-1050

40-351
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D028 Wiring connector for 40-677 40-1301
air conditioner heat 40-695
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1388
air conditioner heat 40-689
exchanger fan wiring
loom
D028 Wiring connector for 40-683 40-1308
roof wiring loom 40-695
40-689
40-677
D029 Connection between 40-677 40-1301
cab power supply 40-1125
wiring and HV roof 40-1067
40-778
wiring
40-695
40-1050
40-1115
40-764
D029 Wiring connector for 40-677 40-1301
cab power wiring 40-1125
loom 40-1067
40-778
40-695
40-1050
40-1115
40-764
D029 Wiring connector for 40-683 40-1388
cab power wiring 40-1016
loom 40-689
40-1001
D029 Wiring connector for 40-683 40-1311
roof wiring loom 40-1125
40-1067
40-1016
40-783
40-778
40-695
40-689
40-1001
40-1050
40-1115
40-677
40-764
40-769
D030 Wiring connector for 40-683 40-1311
central cab wiring 40-1125
loom 40-1067
40-1016
40-783
40-778
40-695
40-689
40-1001
40-1050
40-1115
40-677
40-764
40-769

40-352
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D030 Wiring connector for [LNK] 40-1331
cab power wiring
loom
D030 Wiring connector for 40-683 40-1347
cab power wiring 40-1001
loom 40-1050
40-1115
40-677
40-764
40-769
D030 Wiring connector for 40-689 40-1365
cab power wiring 40-1125
loom 40-1067
40-1016
40-783
40-778
40-695
D031 Wiring connector for 40-657 40-1365
roof wiring loom 40-695
40-689
D031 Wiring connector for 40-647 40-1311
central wiring loom 40-695
40-689
40-657
40-683
40-677
D031 Wiring connector for 40-647 40-1347
roof wiring loom 40-683
40-677
40-728

Table 213
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D032 Wiring connector for 40-677 40-1301
cab power wiring 40-695
loom 40-695
D032 Wiring connector for 40-647 40-1311
roof wiring loom 40-689
40-657
40-683
40-677
D033 Wiring connector for 40-677 40-1301
roof 40-695
D033 Wiring connector to 40-677 40-1301
wiring loom 40-695
D034 Wiring connector for 40-677 40-1301
roof 40-695
D034 Wiring connector to 40-677 40-1301
wiring loom 40-695
D035 Wiring connector for [LNK] 40-1327
central wiring loom
and electronic lift
D038 Wiring connector for 40-710 40-1365
RH side console wir- 40-734
ing loom
D038 Wiring connector for 40-710 40-1386
central wiring loom 40-734
and electronic lift

40-353
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D039 Wiring connector for 40-657 40-1365
power wiring loom 40-870
40-1269
40-1266
40-1243
40-1231
40-1125
40-1067
40-1016
40-970
40-902
40-783
40-778
40-695
40-689
D039 Wiring connector for 40-647 40-1295
central cab wiring 40-870
loom 40-1269
40-1266
40-1243
40-1231
40-1125
40-1067
40-1016
40-970
40-902
40-783
40-778
40-695
40-689
40-657
40-1199
40-1240
40-1115
40-1141
40-1001
40-1050
40-834
40-882
40-935
40-683
40-677
40-764
40-769
D039 Wiring connector for 40-647 40-1347
power wiring loom 40-1199
40-1050
40-1115
40-834
40-882
40-935
40-1001
40-683
40-677
40-764
40-769

40-354
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D040 Wiring connector for 40-657 40-1365
power wiring loom 40-870
40-1269
40-1266
40-1243
40-1231
40-1067
40-1016
40-970
40-902
40-783
40-778
40-734
40-710
40-616
40-695
40-689
D040 Wiring connector for 40-608 40-1347
power wiring loom 40-1250
40-1050
40-1199
40-1240
40-882
40-935
40-1001
40-769
40-834
40-647
40-683
40-677
40-705
40-728
40-764

40-355
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D040 Wiring connector for 40-608 40-1295
central wiring loom 40-870
40-1269
40-1266
40-1243
40-1231
40-1067
40-1016
40-970
40-902
40-783
40-778
40-734
40-710
40-695
40-689
40-657
40-616
40-1199
40-1240
40-1250
40-1001
40-1050
40-882
40-935
40-834
40-769
40-647
40-683
40-677
40-705
40-728
40-764
D041 Wiring connector for [LNK] 40-1296
rear wiring loom
D042 Wiring connector for 40-1199 40-1293
reverse shuttle wir- 40-1231
ing loom (drivetrain)
D042 Wiring connector for 40-1199 40-1296
reverse shuttle wir- 40-1231
ing loom (cab)
D043 Wiring connector 40-728 40-1347
40-834
40-1199
D043 Wiring connector for 40-728 40-1347
switch wiring loom 40-834
40-1199
D044 Wiring connector for 40-764 40-1301
windscreen wiper 40-778
motor wiring loom
D044 Wiring connector for 40-764 40-1279
roof wiring loom 40-778
D045 Wiring connector for [LNK] 40-1388
windscreen wiper
wiring loom
D045 Wiring connector for 40-769 40-1276
roof wiring loom 40-783

40-356
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D046 Wiring connector for 40-1001 40-1388
work lights and wind- 40-1016
screen wiper wiring
loom, versions with-
out high visibility cab
D046 Wiring connector to 40-769 40-1322
cab roof wiring loom, 40-1016
versions with stan- 40-783
40-1001
dard cab

Table 214
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D047 Wiring connector for 40-769 40-1322
rear screen wiper 40-783
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for 40-769 40-1300
work lights and wind- 40-783
screen wiper wiring
loom, versions with-
out high visibility cab
D050 Wiring connector for 40-935 40-1312
RH lower front head- 40-1067
light 40-1016
40-970
40-1001
40-1050
D050 Wiring connector for 40-935 40-1427
low front lights wiring 40-1067
loom 40-1016
40-970
40-1001
40-1050
D051 Wiring connector for 40-1050 40-1288
LH lower headlight
wiring loom
D051 2.8059.528.0 Wiring connector for 40-935 40-1427
front lower work light 40-1067
wiring loom, ver- 40-1016
40-970
sions with high vis-
40-1001
ibility cab 40-1050
D052 Wiring connector for 40-935 40-1427
low front lights wiring 40-1067
loom 40-1016
40-970
40-1001
40-1050
D052 Wiring connector for 40-935 40-1312
LH lower front head- 40-1067
light 40-1016
40-970
40-1001
40-1050

40-357
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D053 2.8059.528.0 Wiring connector for 40-935 40-1427
front lower work light 40-1067
wiring loom, ver- 40-1016
40-970
sions with high vis-
40-1001
ibility cab 40-1050
D053 Wiring connector for [LNK] 40-1288
RH lower headlight
wiring loom
D054 Seat configuration 40-870 40-1365
connector
D054a Seat configuration 40-870 40-1365
connector
D054b Seat configuration 40-870 40-1365
connector
D055 Seat configuration [LNK] 40-1347
connector
D055a Seat configuration 40-834 40-1347
connector
D055b Seat configuration 40-834 40-1347
connector
D057 Wiring connector 40-902 40-1365
40-870
D057 Wiring connector for 40-902 40-1365
parking brake wiring 40-870
loom
D058 Wiring connector 40-834 40-1347
40-882
D058 Wiring connector for 40-834 40-1347
parking brake wiring 40-882
loom

40-358
Wiring diagrams
Table 215
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D060 Wiring connector for 40-902 40-1391
central wiring loom 40-970
D060 Wiring connector for 40-902 40-1365
rear RH work light 40-970
wiring loom
D061 Wiring connector for 40-902 40-1391
central wiring loom 40-970
D061 Wiring connector for 40-902 40-1365
rear LH work light 40-970
wiring loom
D062 Wiring connector for 40-935 40-1427
low front lights wiring 40-1067
loom 40-1016
40-970
40-1001
40-1050
D062 Wiring connector for 40-935 40-1312
LH lower front head- 40-1067
light 40-1016
40-970
40-1001
40-1050
D063 Wiring connector for 40-1050 40-1301
flashing beacon wir- 40-1067
ing loom
D063 Wiring connector for 40-1001 40-1322
flashing beacon wir- 40-1016
ing loom
D063 Wiring connector for 40-1001 40-1286
roof wiring loom 40-1067
40-1016
40-1050
D064 Wiring connector for 40-1050 40-1301
flashing beacon wir- 40-1067
ing loom
D064 Wiring connector for 40-1001 40-1322
flashing beacon wir- 40-1016
ing loom
D064 Wiring connector for 40-1001 40-1286
roof wiring loom 40-1067
40-1016
40-1050
D065 Wiring connector for 40-935 40-1285
central wiring loom
D065 Wiring connector for 40-935 40-1347
RH rear lights wiring
loom
D066 Wiring connector for 40-935 40-1285
central wiring loom
D066 Wiring connector for 40-935 40-1347
LH rear lights wiring
loom

40-359
 Wiring diagrams
Table 216
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D073 2.8039.160.0 Wiring connector for 40-984 40-1289
front work light wir- 40-1067
ing loom 40-1050
40-1033
40-1016
40-1001
D073 Wiring connector for 40-984 40-1282
front lights and horn 40-1067
wiring loom 40-1050
40-1033
40-1016
40-1001
D074 Wiring connector for 40-984 40-1282
front lights and horn 40-1067
wiring loom 40-1050
40-1033
40-1016
40-1001
D074 2.8039.160.0 Wiring connector for 40-984 40-1289
front work light wir- 40-1067
ing loom 40-1050
40-1033
40-1016
40-1001
D075 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
RH front work light 40-1067
D076 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
LH front work light 40-1067
D077 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
LH rear work light 40-1067
D078 2.8039.298.0/20 Wiring connector for 40-1050 40-1301
RH rear work light 40-1067
D079 Wiring connector for 40-1231 40-1365
HL lever wiring loom 40-870
D079 Wiring connector for 40-834 40-1347
HL lever wiring loom 40-1199
D082 Wiring connector for 40-728 40-1327
front PTO control so- 40-734
lenoid valve
D082 Wiring connector for 40-728 40-1324
front PTO control so- 40-734
lenoid valve
D082 Wiring connector for 40-728 40-1281
engine wiring loom 40-734
D084 Wiring connector for [LNK] 40-1295
hydraulic reverse
shuttle wiring loom
on drivetrain
D084 Wiring connector for 40-1199 40-1296
reverse shuttle sole- 40-1231
noid valve
D085 Wiring connector for 40-1199 40-1295
hydraulic reverse 40-1231
shuttle wiring loom
on drivetrain

40-360
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
D085 Wiring connector for 40-1199 40-1296
reverse shuttle sole- 40-1231
noid valve
F004 04411920.4 Front LH sidelight 40-935 40-1427
and turn indicator 40-970

40.2.25 - E - On-board instruments and visual and audible indicators (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001)
ITA version
Table 217
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E001 2.8419.007.0 Horn 40-1099 40-1309
40-1130
E003 2.8339.269.0/50 Instrument panel 40-701 40-1331
40-1247
40-723
40-791
40-877
40-915
40-1145
E004 Trailer pressure 40-877 40-1331
gauge
E009 2.8339.269.0/50 Instrument panel 40-714 40-1392
40-1255
40-1166
40-942
40-889
40-807
40-738
E010 Trailer pressure 40-889 40-1392
gauge
USA version
Table 218
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E001 2.8419.007.0 Horn 40-1110 40-1309
40-1137
E005 2.8339.269.0/50 Instrument panel 40-705 40-1347
40-1247
40-1186
40-928
40-728
40-826
40-882
E006 Trailer pressure 40-882 40-1347
gauge
E011 2.8339.269.0/50 Instrument panel 40-719 40-1410
40-1255
40-1206
40-953
40-743
40-843
40-895
E012 Trailer pressure 40-895 40-1410
gauge

40-361
 Wiring diagrams
40.2.26 - E - On-board instruments and visual and audible indicators (AGROFARM 430 ->
ZKDW430200TD25001)
ITA version
Table 219
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E001 2.8419.007.0 Horn 40-1099 40-1309
40-1130
40-1120
E003 2.8339.269.0/50 Instrument panel 40-701 40-1331
40-1247
40-723
40-791
40-877
40-915
40-1145
E004 Trailer pressure 40-877 40-1331
gauge
E007 2.8339.269.0/50 Instrument panel 40-710 40-1365
40-1262
40-1226
40-964
40-902
40-862
40-734
E008 Trailer pressure [LNK] 40-1365
gauge
E009 2.8339.269.0/50 Instrument panel 40-889 40-1392
40-1255
40-1166
40-953
40-889
40-807
40-738
40-714
E010 Trailer pressure 40-889 40-1392
gauge 40-889
E013 Lift console 40-734 40-1386
USA version
Table 220
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E001 2.8419.007.0 Horn 40-1110 40-1309
40-1137
40-1120
E005 2.8339.269.0/50 Instrument panel 40-705 40-1347
40-826
40-1247
40-928
40-728
40-826
40-882
E006 Trailer pressure 40-882 40-1347
gauge

40-362
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E007 2.8339.269.0/50 Instrument panel 40-710 40-1365
40-1262
40-1226
40-964
40-902
40-862
40-734
E008 Trailer pressure [LNK] 40-1365
gauge
E011 2.8339.269.0/50 Instrument panel 40-895 40-1410
40-1206
40-1255
40-964
40-743
40-719
E012 Trailer pressure 40-895 40-1410
gauge

40.2.27 - E - On-board instruments and visual and audible indicators (AGROFARM 410 ->
ZKDW470200TD30001)
ITA version
Table 221
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E002 2.8419.007.0 Horn 40-1105 40-1289
40-1133
E003 2.8339.269.0/50 Instrument panel 40-701 40-1331
40-1250
40-723
40-799
40-877
40-922
40-1151
E004 Trailer pressure 40-877 40-1331
gauge
E009 2.8339.269.0/50 Instrument panel 40-714 40-1392
40-1258
40-1171
40-948
40-889
40-816
40-738
E010 Trailer pressure 40-889 40-1392
gauge
USA version
Table 222
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E002 2.8419.007.0 Horn 40-1115 40-1289
40-1141
E005 2.8339.269.0/50 Instrument panel 40-705 40-1347
40-1250
40-1192
40-935
40-728
40-834
40-882

40-363
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E006 Trailer pressure 40-882 40-1347
gauge
E011 2.8339.269.0/50 Instrument panel 40-719 40-1410
40-1258
40-1211
40-959
40-743
40-852
40-895
E012 Trailer pressure 40-895 40-1410
gauge

40.2.28 - E - On-board instruments and visual and audible indicators (AGROFARM 420 ->
ZKDW510200TD30001)
ITA version
Table 223
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E002 2.8419.007.0 Horn 40-1105 40-1289
40-1133
E003 2.8339.269.0/50 Instrument panel 40-701 40-1331
40-1250
40-723
40-799
40-877
40-922
40-1158
E004 Trailer pressure 40-877 40-1331
gauge
E009 2.8339.269.0/50 Instrument panel 40-714 40-1392
40-1258
40-1178
40-948
40-889
40-816
40-738
E010 Trailer pressure 40-889 40-1392
gauge
USA version
Table 224
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E002 2.8419.007.0 Horn 40-1115 40-1289
40-1141
E005 2.8339.269.0/50 Instrument panel 40-705 40-1347
40-1250
40-1199
40-935
40-728
40-834
40-882
E006 Trailer pressure 40-882 40-1347
gauge

40-364
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E011 2.8339.269.0/50 Instrument panel 40-719 40-1410
40-1258
40-1218
40-959
40-743
40-852
40-895
E012 Trailer pressure 40-895 40-1410
gauge

40.2.29 - E - On-board instruments and visual and audible indicators (AGROFARM 430 ->
ZKDW550200TD30001)
ITA version
Table 225
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E002 2.8419.007.0 Horn 40-1105 40-1289
40-1125
E003 2.8339.269.0/50 Instrument panel 40-701 40-1331
40-1250
40-723
40-799
40-877
40-922
40-1158
E004 Trailer pressure 40-877 40-1331
gauge
E007 2.8339.269.0/50 Instrument panel 40-710 40-1365
40-1266
40-1231
40-970
40-902
40-870
40-734
E008 Trailer pressure [LNK] 40-1365
gauge
E013 Lift console 40-734 40-1386
USA version
Table 226
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E002 2.8419.007.0 Horn 40-1115 40-1289
E005 2.8339.269.0/50 Instrument panel 40-705 40-1347
40-1250
40-935
40-728
40-834
40-882
E006 Trailer pressure 40-882 40-1347
gauge
E007 2.8339.269.0/50 Instrument panel 40-710 40-1365
40-1266
40-1231
40-970
40-902
40-870
40-734

40-365
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
E008 Trailer pressure [LNK] 40-1365
gauge

40.2.30 - F - External lights (rotating beacon) (AGROFARM 410 -> ZKDW350200TD25001,

AGROFARM 420 -> ZKDW390200TD25001)
ITA version
Table 227
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F003 04411921.4 Front RH sidelight 40-915 40-1427
and turn indicator
F005 Number plate light 40-915 40-1331
F006 2.8039.298.0/20 Front work light 40-1024 40-1288
F007 2.8039.298.0/20 Front work light 40-1024 40-1288
F008 Work light 40-1076 40-1292
F009 Rotating beacon 40-1076 40-1292
F010 Work light 40-1076 40-1292
F019 RH front work light 40-1024 40-1424
F020 LH front work light 40-1024 40-1424
F023 0.031.0868.4 LH rotating beacon 40-976 40-1286
40-1024
F024 0.031.0868.4 RH rotating beacon 40-976 40-1286
40-1024
F025 Spot light [LNK] 40-1301
F026 RH headlight 40-915 40-1309
40-942
F027 LH headlight 40-915 40-1309
40-942
F028 LH front lights 40-942 40-1317
F029 RH front lights 40-942 40-1317
F032 LH front work light 40-976 40-1322
F033 RH front work light 40-976 40-1322
F034 LH rear work light 40-976 40-1322
F035 RH rear work light 40-976 40-1322
F036 RH rear light [LNK] 40-1285
F037 RH light, USA [LNK] 40-1285
F038 Rear left light [LNK] 40-1285
F039 LH light, USA [LNK] 40-1285
F045 RH light, USA [LNK] 40-1285
F046 LH light, USA [LNK] 40-1285
F050 Number plate light 40-942 40-1392
USA version
Table 228
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F003 04411921.4 Front RH sidelight 40-928 40-1427
and turn indicator
F006 2.8039.298.0/20 Front work light 40-1042 40-1288
F007 2.8039.298.0/20 Front work light 40-1042 40-1288
F008 Work light 40-1087 40-1292
F009 Rotating beacon 40-1087 40-1292
F010 Work light 40-1087 40-1292
F021 LH hazard light 40-928 40-1285
F022 RH hazard light 40-928 40-1285
F023 0.031.0868.4 LH rotating beacon 40-992 40-1286
40-1042
F024 0.031.0868.4 RH rotating beacon 40-992 40-1286
40-1042

40-366
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F025 Spot light [LNK] 40-1301
F026 RH headlight 40-928 40-1309
40-953
F027 LH headlight 40-928 40-1309
40-953
F028 LH front lights 40-953 40-1317
F029 RH front lights 40-953 40-1317
F032 LH front work light 40-992 40-1322
F033 RH front work light 40-992 40-1322
F034 LH rear work light 40-992 40-1322
F035 RH rear work light 40-992 40-1322
F036 RH rear light 40-953 40-1285
F037 RH light, USA 40-953 40-1285
F038 Rear left light 40-953 40-1285
F039 LH light, USA 40-953 40-1285
F042 Rear LH turn indica- 40-928 40-1285
tor
F043 Rear RH turn indica- 40-928 40-1285
tor
F045 RH light, USA 40-953 40-1285
F046 LH light, USA 40-953 40-1285
F049 Number plate light 40-928 40-1347
F051 Number plate light 40-953 40-1410

40.2.31 - F - External lights (rotating beacon) (AGROFARM 430 -> ZKDW430200TD25001)

ITA version
Table 229
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F003 04411921.4 Front RH sidelight 40-915 40-1427
and turn indicator 40-964
F005 Number plate light 40-915 40-1331
F006 2.8039.298.0/20 Front work light 40-1024 40-1288
F007 2.8039.298.0/20 Front work light 40-1024 40-1288
F008 Work light 40-1076 40-1292
F009 Rotating beacon 40-1076 40-1292
F010 Work light 40-1076 40-1292
F019 RH front work light 40-1024 40-1424
40-1059
F020 LH front work light 40-1024 40-1424
40-1059
F023 0.031.0868.4 LH rotating beacon 40-976 40-1286
40-1059
40-1008
40-1024
F024 0.031.0868.4 RH rotating beacon 40-976 40-1286
40-1059
40-1008
40-1024
F025 Spot light [LNK] 40-1301
F026 RH headlight 40-915 40-1309
40-964
40-942
F027 LH headlight 40-915 40-1309
40-964
40-942
F028 LH front lights 40-942 40-1317
F029 RH front lights 40-942 40-1317
F032 LH front work light 40-976 40-1322
40-1008

40-367
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F033 RH front work light 40-976 40-1322
40-1008
F034 LH rear work light 40-976 40-1322
40-1008
F035 RH rear work light 40-976 40-1322
40-1008
F036 RH rear light [LNK] 40-1285
F037 RH light, USA [LNK] 40-1285
F038 Rear left light [LNK] 40-1285
F039 LH light, USA [LNK] 40-1285
F044 2.8059.080.0 RH rear light 40-877 40-1391
40-964
40-902
40-942
40-915
40-889
F045 RH light, USA [LNK] 40-1285
F046 LH light, USA [LNK] 40-1285
F047 2.8059.080.0 LH rear light 40-877 40-1391
40-964
40-902
40-942
40-915
40-889
F048 Number plate light 40-964 40-1365
F050 Number plate light 40-942 40-1392

USA version
Table 230
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F003 04411921.4 Front RH sidelight 40-928 40-1427
and turn indicator 40-964
F006 2.8039.298.0/20 Front work light 40-1042 40-1288
F007 2.8039.298.0/20 Front work light 40-1042 40-1288
F008 Work light 40-1087 40-1292
F009 Rotating beacon 40-1087 40-1292
F010 Work light 40-1087 40-1292
F021 LH hazard light 40-928 40-1285
F022 RH hazard light 40-928 40-1285
F023 0.031.0868.4 LH rotating beacon 40-992 40-1286
40-1059
40-1008
40-1042
F024 0.031.0868.4 RH rotating beacon 40-992 40-1286
40-1059
40-1008
40-1042
F025 Spot light [LNK] 40-1301
F026 RH headlight 40-928 40-1309
40-964
40-953
F027 LH headlight 40-928 40-1309
40-964
40-953
F028 LH front lights 40-953 40-1317
F029 RH front lights 40-953 40-1317
F032 LH front work light 40-992 40-1322
40-1008
F033 RH front work light 40-992 40-1322
40-1008

40-368
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F034 LH rear work light 40-992 40-1322
40-1008
F035 RH rear work light 40-992 40-1322
40-1008
F036 RH rear light 40-953 40-1285
F037 RH light, USA 40-953 40-1285
F038 Rear left light 40-953 40-1285
F039 LH light, USA 40-953 40-1285
F042 Rear LH turn indica- 40-928 40-1285
tor
F043 Rear RH turn indica- 40-928 40-1285
tor
F044 2.8059.080.0 RH rear light 40-902 40-1391
40-964
F045 RH light, USA 40-953 40-1285
F046 LH light, USA 40-953 40-1285
F047 2.8059.080.0 LH rear light 40-902 40-1391
40-964
F048 Number plate light 40-964 40-1365
F049 Number plate light 40-928 40-1347
F051 Number plate light 40-953 40-1410

40.2.32 - F - External lights (rotating beacon) (AGROFARM 410 -> ZKDW470200TD30001)

ITA version
Table 231
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F001 Outer LH front work 40-984 40-1282
light 40-1082
40-1033
F002 Outer RH front work 40-984 40-1282
light 40-1082
40-1033
F003 04411921.4 Front RH sidelight 40-922 40-1427
and turn indicator
F005 Number plate light 40-922 40-1331
F006 2.8039.298.0/20 Front work light 40-1033 40-1288
F007 2.8039.298.0/20 Front work light 40-1033 40-1288
F008 Work light 40-1082 40-1292
F009 Rotating beacon 40-1082 40-1292
F010 Work light 40-1082 40-1292
F019 RH front work light 40-1033 40-1424
F020 LH front work light 40-1033 40-1424
F023 0.031.0868.4 LH rotating beacon 40-984 40-1286
40-1033
F024 0.031.0868.4 RH rotating beacon 40-984 40-1286
40-1033
F025 Spot light [LNK] 40-1301
F028 LH front lights 40-948 40-1317
F029 RH front lights 40-948 40-1317
F032 LH front work light 40-984 40-1322
F033 RH front work light 40-984 40-1322
F034 LH rear work light 40-984 40-1322
F035 RH rear work light 40-984 40-1322
F036 RH rear light [LNK] 40-1285
F037 RH light, USA [LNK] 40-1285
F038 Rear left light [LNK] 40-1285
F039 LH light, USA [LNK] 40-1285
F040 2.8039.240.0 LH light 40-922 40-1289
40-948

40-369
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F041 2.8039.240.0 RH light 40-922 40-1289
40-948
F045 RH light, USA [LNK] 40-1285
F046 LH light, USA [LNK] 40-1285
F050 Number plate light 40-948 40-1392
USA version
Table 232
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F001 Outer LH front work 40-1001 40-1282
light 40-1093
40-1050
F002 Outer RH front work 40-1001 40-1282
light 40-1093
40-1050
F003 04411921.4 Front RH sidelight 40-935 40-1427
and turn indicator
F006 2.8039.298.0/20 Front work light 40-1050 40-1288
F007 2.8039.298.0/20 Front work light 40-1050 40-1288
F008 Work light 40-1093 40-1292
F009 Rotating beacon 40-1093 40-1292
F010 Work light 40-1093 40-1292
F021 LH hazard light 40-935 40-1285
F022 RH hazard light 40-935 40-1285
F023 0.031.0868.4 LH rotating beacon 40-1001 40-1286
40-1050
F024 0.031.0868.4 RH rotating beacon 40-1001 40-1286
40-1050
F025 Spot light [LNK] 40-1301
F028 LH front lights 40-959 40-1317
F029 RH front lights 40-959 40-1317
F032 LH front work light 40-1001 40-1322
F033 RH front work light 40-1001 40-1322
F034 LH rear work light 40-1001 40-1322
F035 RH rear work light 40-1001 40-1322
F036 RH rear light 40-959 40-1285
F037 RH light, USA 40-959 40-1285
F038 Rear left light 40-959 40-1285
F039 LH light, USA 40-959 40-1285
F040 2.8039.240.0 LH light 40-935 40-1289
40-959
F041 2.8039.240.0 RH light 40-935 40-1289
40-959
F042 Rear LH turn indica- 40-935 40-1285
tor
F043 Rear RH turn indica- 40-935 40-1285
tor
F045 RH light, USA 40-959 40-1285
F046 LH light, USA 40-959 40-1285
F049 Number plate light 40-935 40-1347
F051 Number plate light 40-959 40-1410

40.2.33 - F - External lights (rotating beacon) (AGROFARM 420 -> ZKDW510200TD30001)

40-370
Wiring diagrams
ITA version
Table 233
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F001 Outer LH front work 40-984 40-1282
light 40-1082
40-1033
F002 Outer RH front work 40-984 40-1282
light 40-1082
40-1033
F003 04411921.4 Front RH sidelight 40-922 40-1427
and turn indicator
F005 Number plate light 40-922 40-1331
F006 2.8039.298.0/20 Front work light 40-1033 40-1288
F007 2.8039.298.0/20 Front work light 40-1033 40-1288
F008 Work light 40-1082 40-1292
F009 Rotating beacon 40-1082 40-1292
F010 Work light 40-1082 40-1292
F019 RH front work light 40-1033 40-1424
F020 LH front work light 40-1033 40-1424
F023 0.031.0868.4 LH rotating beacon 40-984 40-1286
40-1033
F024 0.031.0868.4 RH rotating beacon 40-984 40-1286
40-1033
F025 Spot light [LNK] 40-1301
F028 LH front lights 40-948 40-1317
F029 RH front lights 40-948 40-1317
F032 LH front work light 40-984 40-1322
F033 RH front work light 40-984 40-1322
F034 LH rear work light 40-984 40-1322
F035 RH rear work light 40-984 40-1322
F036 RH rear light [LNK] 40-1285
F037 RH light, USA [LNK] 40-1285
F038 Rear left light [LNK] 40-1285
F039 LH light, USA [LNK] 40-1285
F040 2.8039.240.0 LH light 40-922 40-1289
40-948
F041 2.8039.240.0 RH light 40-922 40-1289
40-948
F044 2.8059.080.0 RH rear light 40-877 40-1391
40-948
40-922
40-889
F045 RH light, USA [LNK] 40-1285
F046 LH light, USA [LNK] 40-1285
F047 2.8059.080.0 LH rear light 40-877 40-1391
40-948
40-922
40-889
F050 Number plate light 40-948 40-1392
USA version
Table 234
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F001 Outer LH front work 40-1001 40-1282
light 40-1093
40-1050
F002 Outer RH front work 40-1001 40-1282
light 40-1093
40-1050

40-371
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F003 04411921.4 Front RH sidelight 40-935 40-1427
and turn indicator
F006 2.8039.298.0/20 Front work light 40-1050 40-1288
F007 2.8039.298.0/20 Front work light 40-1050 40-1288
F008 Work light 40-1093 40-1292
F009 Rotating beacon 40-1093 40-1292
F010 Work light 40-1093 40-1292
F021 LH hazard light 40-935 40-1285
F022 RH hazard light 40-935 40-1285
F023 0.031.0868.4 LH rotating beacon 40-1001 40-1286
40-1050
F024 0.031.0868.4 RH rotating beacon 40-1001 40-1286
40-1050
F025 Spot light [LNK] 40-1301
F028 LH front lights 40-959 40-1317
F029 RH front lights 40-959 40-1317
F032 LH front work light 40-1001 40-1322
F033 RH front work light 40-1001 40-1322
F034 LH rear work light 40-1001 40-1322
F035 RH rear work light 40-1001 40-1322
F036 RH rear light 40-959 40-1285
F037 RH light, USA 40-959 40-1285
F038 Rear left light 40-959 40-1285
F039 LH light, USA 40-959 40-1285
F040 2.8039.240.0 LH light 40-935 40-1289
40-959
F041 2.8039.240.0 RH light 40-935 40-1289
40-959
F042 Rear LH turn indica- 40-935 40-1285
tor
F043 Rear RH turn indica- 40-935 40-1285
tor
F044 2.8059.080.0 RH rear light [LNK] 40-1391
F045 RH light, USA 40-959 40-1285
F046 LH light, USA 40-959 40-1285
F047 2.8059.080.0 LH rear light [LNK] 40-1391
F049 Number plate light 40-935 40-1347
F051 Number plate light 40-959 40-1410

40-372
Wiring diagrams
40.2.34 - F - External lights (rotating beacon) (AGROFARM 430 -> ZKDW550200TD30001)
ITA version
Table 235
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F001 Outer LH front work 40-984 40-1282
light 40-1067
40-1016
40-1082
40-1033
F002 Outer RH front work 40-984 40-1282
light 40-1067
40-1016
40-1082
40-1033
F003 04411921.4 Front RH sidelight 40-922 40-1427
and turn indicator 40-970
F005 Number plate light 40-922 40-1331
F006 2.8039.298.0/20 Front work light 40-1033 40-1288
F007 2.8039.298.0/20 Front work light 40-1033 40-1288
F019 RH front work light 40-1033 40-1424
40-1067
F020 LH front work light 40-1033 40-1424
40-1067
F023 0.031.0868.4 LH rotating beacon 40-984 40-1286
40-1067
40-1016
40-1033
F024 0.031.0868.4 RH rotating beacon 40-984 40-1286
40-1067
40-1016
40-1033
F025 Spot light [LNK] 40-1301
F032 LH front work light 40-984 40-1322
40-1016
F033 RH front work light 40-984 40-1322
40-1016
F034 LH rear work light 40-984 40-1322
40-1016
F035 RH rear work light 40-984 40-1322
40-1016
F040 2.8039.240.0 LH light 40-922 40-1289
40-970
40-948
F041 2.8039.240.0 RH light 40-922 40-1289
40-970
40-948
F044 2.8059.080.0 RH rear light 40-877 40-1391
40-970
40-902
40-922
40-889
F047 2.8059.080.0 LH rear light 40-877 40-1391
40-970
40-902
40-922
40-889
F048 Number plate light 40-970 40-1365

40-373
 Wiring diagrams
USA version
Table 236
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
F001 Outer LH front work 40-1001 40-1282
light 40-1067
40-1016
40-1093
40-1050
F002 Outer RH front work 40-1001 40-1282
light 40-1067
40-1016
40-1093
40-1050
F003 04411921.4 Front RH sidelight 40-935 40-1427
and turn indicator 40-970
F006 2.8039.298.0/20 Front work light 40-1050 40-1288
F007 2.8039.298.0/20 Front work light 40-1050 40-1288
F021 LH hazard light 40-935 40-1285
F022 RH hazard light 40-935 40-1285
F023 0.031.0868.4 LH rotating beacon 40-1001 40-1286
40-1067
40-1016
40-1050
F024 0.031.0868.4 RH rotating beacon 40-1001 40-1286
40-1067
40-1016
40-1050
F025 Spot light [LNK] 40-1301
F032 LH front work light 40-1001 40-1322
40-1016
F033 RH front work light 40-1001 40-1322
40-1016
F034 LH rear work light 40-1001 40-1322
40-1016
F035 RH rear work light 40-1001 40-1322
40-1016
F040 2.8039.240.0 LH light 40-935 40-1289
40-970
40-959
F041 2.8039.240.0 RH light 40-935 40-1289
40-970
40-959
F042 Rear LH turn indica- 40-935 40-1285
tor
F043 Rear RH turn indica- 40-935 40-1285
tor
F044 2.8059.080.0 RH rear light 40-902 40-1391
40-970
F047 2.8059.080.0 LH rear light 40-902 40-1391
40-970
F048 Number plate light 40-970 40-1365
F049 Number plate light 40-935 40-1347

40.2.35 - G - Interior lights (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 420

-> ZKDW390200TD25001)
Table 237
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
G001 AC controls lighting [LNK] 40-1301
G002 Interior roof light [LNK] 40-1301

40-374
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
G003 AC LED 40-671 40-1301
40-677
G004 Interior roof light [LNK] 40-1318
G005 Light unit [LNK] 40-1388

40.2.36 - G - Interior lights (AGROFARM 430 -> ZKDW430200TD25001)

Table 238
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
G001 AC controls lighting [LNK] 40-1301
G002 Interior roof light [LNK] 40-1301
G003 AC LED 40-671 40-1301
40-695
40-677
G004 Interior roof light [LNK] 40-1318
G005 Light unit [LNK] 40-1388

40.2.37 - G - Interior lights (AGROFARM 410 -> ZKDW470200TD30001)

Table 239
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
G001 AC controls lighting [LNK] 40-1301
G002 Interior roof light [LNK] 40-1301
G003 AC LED 40-671 40-1301
40-677
G005 Light unit [LNK] 40-1388

40.2.38 - G - Interior lights (AGROFARM 420 -> ZKDW510200TD30001)

Table 240
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
G001 AC controls lighting [LNK] 40-1301
G002 Interior roof light [LNK] 40-1301
G003 AC LED 40-671 40-1301
40-677
G005 Light unit [LNK] 40-1388

40.2.39 - G - Interior lights (AGROFARM 430 -> ZKDW550200TD30001)

Table 241
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
G001 AC controls lighting [LNK] 40-1301
G002 Interior roof light [LNK] 40-1301
G003 AC LED 40-671 40-1301
40-695
40-677
G005 Light unit [LNK] 40-1388

40.2.40 - H - Manual electrical controls (steering column switch) (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001)
ITA version
Table 242
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H001 Blower speed selec- 40-641 40-1274
tor switch

40-375
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H002 Blower speed selec- 40-665 40-1275
tor switch
H003 Air conditioning tem- 40-665 40-1275
perature thermostat
H005 4-speed fan control 40-671 40-1301
H007 Mechanical thermo- 40-671 40-1301
stat
H008 Windscreen wiper 40-750 40-1301
timer
H009 Blower speed selec- [LNK] 40-1318
tor switch
H010 Timer 40-758 40-1318
H012 Light selector control 40-915 40-1331
40-1099
H013 04429390/10 Mechanical hand 40-701 40-1331
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H014 Accelerator pedal 40-701 40-1331

H015 Parking brake 40-791 40-1331
40-877
H024 Light selector control 40-942 40-1392
40-1130
H025 04429390/10 Mechanical hand 40-714 40-1392
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H026 Accelerator pedal 40-714 40-1392

H027 Parking brake 40-807 40-1392
40-889
H031 Windscreen wipers [LNK] 40-1388
timer
H032 HI/LO lever [LNK] 40-1423

40-376
Wiring diagrams
USA version
Table 243
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H001 Blower speed selec- 40-652 40-1274
tor switch
H002 Blower speed selec- 40-683 40-1275
tor switch
H003 Air conditioning tem- 40-683 40-1275
perature thermostat
H005 4-speed fan control 40-677 40-1301
H006 Parking brake 40-843 40-1410
40-895
H007 Mechanical thermo- 40-677 40-1301
stat
H008 Windscreen wiper 40-764 40-1301
timer
H009 Blower speed selec- [LNK] 40-1318
tor switch
H010 Timer 40-772 40-1318
H016 Light selector control 40-928 40-1347
40-1110
H017 04429390/10 Mechanical hand 40-705 40-1347
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H018 Accelerator pedal 40-705 40-1347

H019 Parking brake 40-826 40-1347
40-882
H028 Light selector control 40-953 40-1410
40-1137
H029 04429390/10 Mechanical hand 40-719 40-1410
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H030 Accelerator pedal 40-719 40-1410

H031 Windscreen wipers [LNK] 40-1388
timer
H032 HI/LO lever [LNK] 40-1423

40.2.41 - H - Manual electrical controls (steering column switch) (AGROFARM 430 ->
ZKDW430200TD25001)
ITA version
Table 244
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H001 Blower speed selec- 40-641 40-1274
tor switch 40-660

40-377
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H002 Blower speed selec- 40-665 40-1275
tor switch 40-689
H003 Air conditioning tem- 40-665 40-1275
perature thermostat 40-689
H005 4-speed fan control 40-671 40-1301
40-695
H007 Mechanical thermo- 40-671 40-1301
stat 40-695
H008 Windscreen wiper 40-750 40-1301
timer 40-778
H009 Blower speed selec- [LNK] 40-1318
tor switch
H010 Timer 40-758 40-1318
H012 Light selector control 40-915 40-1331
40-1099
H013 04429390/10 Mechanical hand 40-701 40-1331
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H014 Accelerator pedal 40-701 40-1331

H015 Parking brake 40-791 40-1331
40-877
H020 Light selector control 40-964 40-1365
40-1120
H021 04429390/10 Mechanical hand 40-710 40-1365
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H022 Accelerator pedal 40-710 40-1365

H023 Parking brake 40-862 40-1365
40-902
H024 Light selector control 40-953 40-1392
40-1130
H025 04429390/10 Mechanical hand 40-714 40-1392
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H026 Accelerator pedal 40-714 40-1392

H027 Parking brake 40-807 40-1392
40-889
40-889
H031 Windscreen wipers [LNK] 40-1388
timer
H032 HI/LO lever [LNK] 40-1423

40-378
Wiring diagrams
USA version
Table 245
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H001 Blower speed selec- 40-652 40-1274
tor switch 40-660
H002 Blower speed selec- 40-683 40-1275
tor switch 40-689
H003 Air conditioning tem- 40-683 40-1275
perature thermostat 40-689
H005 4-speed fan control 40-677 40-1301
40-695
H006 Parking brake 40-895 40-1410
40-895
H007 Mechanical thermo- 40-677 40-1301
stat 40-695
H008 Windscreen wiper 40-764 40-1301
timer 40-778
H009 Blower speed selec- [LNK] 40-1318
tor switch
H010 Timer 40-772 40-1318
H016 Light selector control 40-928 40-1347
40-1110
H017 04429390/10 Mechanical hand 40-705 40-1347
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H018 Accelerator pedal 40-705 40-1347

40-826
H019 Parking brake 40-826 40-1347
40-882
H020 Light selector control 40-964 40-1365
40-1120
H021 04429390/10 Mechanical hand 40-710 40-1365
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H022 Accelerator pedal 40-710 40-1365

H023 Parking brake 40-862 40-1365
40-902
H028 Light selector control 40-964 40-1410
40-1137

40-379
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H029 04429390/10 Mechanical hand 40-719 40-1410
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H030 Accelerator pedal 40-719 40-1410

H031 Windscreen wipers [LNK] 40-1388
timer
H032 HI/LO lever [LNK] 40-1423

40.2.42 - H - Manual electrical controls (steering column switch) (AGROFARM 410 ->
ZKDW470200TD30001)
ITA version
Table 246
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H001 Blower speed selec- [LNK] 40-1274
tor switch
H002 Blower speed selec- 40-665 40-1275
tor switch
H003 Air conditioning tem- 40-665 40-1275
perature thermostat
H004 Shuttle lever 40-600 40-1293
40-1258
40-1250
40-1171
40-1151
40-625
40-799
40-816
H005 4-speed fan control 40-671 40-1301
H007 Mechanical thermo- 40-671 40-1301
stat
H008 Windscreen wiper 40-750 40-1301
timer
H012 Light selector control 40-922 40-1331
40-1105
H013 04429390/10 Mechanical hand 40-701 40-1331
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H014 Accelerator pedal 40-701 40-1331

H015 Parking brake 40-799 40-1331
40-877
H024 Light selector control 40-948 40-1392
40-1133

40-380
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H025 04429390/10 Mechanical hand 40-714 40-1392
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H026 Accelerator pedal 40-714 40-1392

H027 Parking brake 40-816 40-1392
40-889
H031 Windscreen wipers [LNK] 40-1388
timer

USA version
Table 247
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H001 Blower speed selec- [LNK] 40-1274
tor switch
H002 Blower speed selec- 40-683 40-1275
tor switch
H003 Air conditioning tem- 40-683 40-1275
perature thermostat
H004 Shuttle lever 40-608 40-1293
40-1258
40-1250
40-1192
40-1211
40-633
40-834
40-852
H005 4-speed fan control 40-677 40-1301
H006 Parking brake 40-852 40-1410
40-895
H007 Mechanical thermo- 40-677 40-1301
stat
H008 Windscreen wiper 40-764 40-1301
timer
H016 Light selector control 40-935 40-1347
40-1115
H017 04429390/10 Mechanical hand 40-705 40-1347
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H018 Accelerator pedal 40-705 40-1347

H019 Parking brake 40-834 40-1347
40-882
H028 Light selector control 40-959 40-1410
40-1141

40-381
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H029 04429390/10 Mechanical hand 40-719 40-1410
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H030 Accelerator pedal 40-719 40-1410

H031 Windscreen wipers [LNK] 40-1388
timer

40.2.43 - H - Manual electrical controls (steering column switch) (AGROFARM 420 ->
ZKDW510200TD30001)
ITA version
Table 248
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H001 Blower speed selec- [LNK] 40-1274
tor switch
H002 Blower speed selec- 40-665 40-1275
tor switch
H003 Air conditioning tem- 40-665 40-1275
perature thermostat
H004 Shuttle lever 40-600 40-1293
40-1258
40-1250
40-1178
40-1158
40-625
40-799
40-816
H005 4-speed fan control 40-671 40-1301
H007 Mechanical thermo- 40-671 40-1301
stat
H008 Windscreen wiper 40-750 40-1301
timer
H012 Light selector control 40-922 40-1331
40-1105
H013 04429390/10 Mechanical hand 40-701 40-1331
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H014 Accelerator pedal 40-701 40-1331

H015 Parking brake 40-799 40-1331
40-877
H024 Light selector control 40-948 40-1392
40-1133

40-382
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H025 04429390/10 Mechanical hand 40-714 40-1392
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H026 Accelerator pedal 40-714 40-1392

H027 Parking brake 40-816 40-1392
40-889
H031 Windscreen wipers [LNK] 40-1388
timer
USA version
Table 249
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H001 Blower speed selec- [LNK] 40-1274
tor switch
H002 Blower speed selec- 40-683 40-1275
tor switch
H003 Air conditioning tem- 40-683 40-1275
perature thermostat
H004 Shuttle lever 40-608 40-1293
40-1258
40-1250
40-1199
40-1218
40-633
40-834
40-852
H005 4-speed fan control 40-677 40-1301
H006 Parking brake 40-852 40-1410
40-895
H007 Mechanical thermo- 40-677 40-1301
stat
H008 Windscreen wiper 40-764 40-1301
timer
H016 Light selector control 40-935 40-1347
40-1115
H017 04429390/10 Mechanical hand 40-705 40-1347
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H018 Accelerator pedal 40-705 40-1347

H019 Parking brake 40-834 40-1347
40-882
H028 Light selector control 40-959 40-1410
40-1141

40-383
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H029 04429390/10 Mechanical hand 40-719 40-1410
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H030 Accelerator pedal 40-719 40-1410

H031 Windscreen wipers [LNK] 40-1388
timer

40.2.44 - H - Manual electrical controls (steering column switch) (AGROFARM 430 ->
ZKDW550200TD30001)
ITA version
Table 250
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H001 Blower speed selec- 40-641 40-1274
tor switch
H002 Blower speed selec- 40-665 40-1275
tor switch 40-689
H003 Air conditioning tem- 40-665 40-1275
perature thermostat 40-689
H004 Shuttle lever 40-600 40-1293
40-1266
40-1250
40-1231
40-616
40-799
40-870
40-1158
H005 4-speed fan control 40-671 40-1301
40-695
H007 Mechanical thermo- 40-671 40-1301
stat 40-695
H008 Windscreen wiper 40-750 40-1301
timer 40-778
H012 Light selector control 40-922 40-1331
40-1105
H013 04429390/10 Mechanical hand 40-701 40-1331
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H014 Accelerator pedal 40-701 40-1331

H015 Parking brake 40-791 40-1331
40-799
40-877
H020 Light selector control 40-970 40-1365
40-1125

40-384
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H021 04429390/10 Mechanical hand 40-710 40-1365
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H022 Accelerator pedal 40-710 40-1365

H023 Parking brake 40-870 40-1365
40-902
H031 Windscreen wipers [LNK] 40-1388
timer

USA version
Table 251
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H001 Blower speed selec- [LNK] 40-1274
tor switch
H002 Blower speed selec- 40-683 40-1275
tor switch 40-689
H003 Air conditioning tem- 40-683 40-1275
perature thermostat 40-689
H004 Shuttle lever 40-608 40-1293
40-1266
40-1250
40-1231
40-616
40-834
40-870
40-1199
H005 4-speed fan control 40-677 40-1301
40-695
H007 Mechanical thermo- 40-677 40-1301
stat 40-695
H008 Windscreen wiper 40-764 40-1301
timer 40-778
H016 Light selector control 40-935 40-1347
40-1115
H017 04429390/10 Mechanical hand 40-705 40-1347
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H018 Accelerator pedal 40-705 40-1347

H019 Parking brake 40-834 40-1347
40-882
H020 Light selector control 40-970 40-1365
40-1125

40-385
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
H021 04429390/10 Mechanical hand 40-710 40-1365
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H022 Accelerator pedal 40-710 40-1365

H023 Parking brake 40-870 40-1365
40-902
H031 Windscreen wipers [LNK] 40-1388
timer

40.2.45 - I - Circuit breakers (AGROFARM 410 -> ZKDW350200TD25001)

ITA version
Table 252
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1024 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1024 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I003 2.7659.159.0 Rotating beacon 0

1
40-1024 40-1301
switch 7

8
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I004 2.7659.224.0/10 Windscreen wiper 40-750 40-1301

switch

I005 2.7659.192.0/10 Rear screen wiper 40-750 40-1301

switch

I006 2.7659.223.0/10 Windscreen washer 40-750 40-1301

button

40-386
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I007 2.7659.343.0/10 Start enable switch 40-596 40-1306
(transmission in neu- 40-1166
tral) 40-621
40-807
40-1145

3,9 Ohm
I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
SYNCRO Pin 2: Normally 40-807
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-791

CB A
I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
ECO Pin 2: Normally 40-807
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-791
CB A

I010 2.7659.079.0 Rear work light 0

40-976 40-1318
switch
1

Pin 1 2
Pos

I011 2.7659.091.0 Rear screen wiper 0

40-758 40-1318
switch
1
3

1
2
4

Pin 1 2
Pos

I012 2.7659.146.0 Windscreen washer 1

0
40-758 40-1318
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

I013 2.7659.126.0 Rotating beacon 0

40-976 40-1318
switch
1

Pin 1 2
Pos

I014 2.7659.092.0 Windscreen wiper 1

0
40-758 40-1318
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

40-387
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I015 2.7659.078.0 Front work lights 0
40-976 40-1318
switch
1

Pin 1 2
Pos

I016 2.7659.126.0 Rotating beacon 0

40-976 40-1388
switch
1

Pin 1 2
Pos

I017 2.7659.092.0 Windscreen wiper 1

0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I018 2.7659.091.0 Rear screen wiper 0

[LNK] 40-1388
switch
1

1
2
4

Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-976 40-1388
switch
1

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-976 40-1388
switch
1

Pin 1 2
Pos

I021 2.7659.146.0 Windscreen washer 1

0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

I022 2.7659.177.0/20 Front PTO switch Resistance between 40-723 40-1331

Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I023 LH external PTO 40-723 40-1331
control
I024 RH external PTO 40-723 40-1331
control
I025 Lights switch 40-915 40-1331
I026 Top lights switch 40-915 40-1331

40-388
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I027 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-596 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1145
Pin 4: normally open
(NO) switch
1

I028 Engine memory 40-701 40-1331

switch
I029 Brake lights switch 40-877 40-1331
I030 Corner work lights 40-976 40-1331
control switch 40-1024
I031 2.7659.152.0/10 Differential lock 40-791 40-1331
switch 40-1145

I032 2.7659.350.0 Rear PTO switch 1 40-723 40-1331

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I033 2.7659.151.0/20 Dual traction switch 40-791 40-1331

40-1145

I034 2.7659.158.0 Hazard warning 40-915 40-1331

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I035 0.015.0485.4 Starter switch 40-596 40-1331

83
50
40-1247
40-1237
30
86s

40-1145
75 15

40-1024
Pos
Pin 30 15 50 75 83 40-976
0 40-915
1 40-877
2 40-791
D0010060 40-758
40-755
40-750
40-723
40-701
40-665
40-671
40-641
40-637

40-389
 Wiring diagrams
Table 253
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I036 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-723 40-1331
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-791
Pin 4: normally open
(NO) switch
1

I037 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-723 40-1331
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-791
Pin 4: normally open
(NO) switch
1

I059 2.7659.156.0 Low work lights 0

1
40-976 40-1331
switch 7

8
40-1024
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

Table 254
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I075 LH external PTO 40-738 40-1392
control
I076 RH external PTO 40-738 40-1392
control
I077 Lights switch 40-942 40-1392
I078 Top lights switch 40-942 40-1392
I079 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-621 40-1392
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1166
Pin 4: normally open
(NO) switch
1

I080 Brake lights switch 40-889 40-1392

I081 Engine memory 40-714 40-1392
switch
I082 2.7659.152.0/10 Differential lock 40-807 40-1392
switch 40-1166

40-390
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I083 2.7659.350.0 Rear PTO switch 1 40-738 40-1392
2
3

2 220 ohm
1W
1 270 ohm

3 1W

I084 2.7659.151.0/20 Dual traction switch 40-807 40-1392

40-1166

I085 2.7659.277.0 Front PTO switch 40-738 40-1392

I086 2.7659.158.0 Hazard warning 40-942 40-1392

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I087 0.015.0485.4 Starter switch 40-621 40-1392

83
50
40-1255
40-1166
30
86s

40-1076
75 15

40-942
Pos
Pin 30 15 50 75 83 40-889
0 40-807
1 40-738
2 40-714
D0010060

I088 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-738 40-1392
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-807
Pin 4: normally open
(NO) switch
1

I089 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-738 40-1392
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-807
Pin 4: normally open
(NO) switch
1

40-391
 Wiring diagrams
Table 255
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-671 40-1301
switch
I110 Rotating beacon 40-1076 40-1392
switch
I111 Corner work light 40-1076 40-1392
switches
I115 2.7659.157.0 Low work lights 40-1076 40-1392
switch

USA version
Table 256
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1042 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1042 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I003 2.7659.159.0 Rotating beacon 0

1
40-1042 40-1301
switch 7

8
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I004 2.7659.224.0/10 Windscreen wiper 40-764 40-1301

switch

I005 2.7659.192.0/10 Rear screen wiper 40-764 40-1301

switch

I006 2.7659.223.0/10 Windscreen washer 40-764 40-1301

button

40-392
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I007 2.7659.343.0/10 Start enable switch 40-604 40-1306
(transmission in neu- 40-1206
tral) 40-629
40-843
40-1186

3,9 Ohm
I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
SYNCRO Pin 2: Normally 40-843
closed (NC) contact
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-826

CB A
I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
ECO Pin 2: Normally 40-843
closed (NC) contact
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-826
CB A

I010 2.7659.079.0 Rear work light 0

40-992 40-1318
switch
1

Pin 1 2
Pos

I011 2.7659.091.0 Rear screen wiper 0

40-772 40-1318
switch
1
3

1
2
4

Pin 1 2
Pos

I012 2.7659.146.0 Windscreen washer 1

0
40-772 40-1318
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

I013 2.7659.126.0 Rotating beacon 0

40-992 40-1318
switch
1

Pin 1 2
Pos

I014 2.7659.092.0 Windscreen wiper 1

0
40-772 40-1318
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

40-393
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I015 2.7659.078.0 Front work lights 0
40-992 40-1318
switch
1

Pin 1 2
Pos

I016 2.7659.126.0 Rotating beacon 0

40-992 40-1388
switch
1

Pin 1 2
Pos

I017 2.7659.092.0 Windscreen wiper 1

0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I018 2.7659.091.0 Rear screen wiper 0

[LNK] 40-1388
switch
1

1
2
4

Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-992 40-1388
switch
1

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-992 40-1388
switch
1

Pin 1 2
Pos

I021 2.7659.146.0 Windscreen washer 1

0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

40-394
Wiring diagrams
Table 257
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I038 2.7659.158.0 Hazard warning 40-826 40-1347
0
1
5 17

40-928
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I039 2.7659.177.0/20 Front PTO switch Resistance between 40-728 40-1347

Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I040 2.7659.350.0 Rear PTO switch 1 40-728 40-1347
2
3

2 220 ohm
1W
1 270 ohm

3 1W

I041 Lights switch 40-928 40-1347

I042 Top lights switch 40-928 40-1347
I043 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-604 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1186
Pin 4: normally open
(NO) switch
1

I044 Engine memory 40-705 40-1347

switch 40-826
I045 0.015.0485.4 Starter switch 40-604 40-1347
83
50
40-1247
40-1240
30
86s

40-1186
75 15

40-1042
Pos
Pin 30 15 50 75 83 40-992
0 40-928
1 40-882
2 40-826
D0010060 40-769
40-772
40-764
40-728
40-705
40-683
40-677
40-647
40-652

40-395
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I046 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-728 40-1347
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-826
Pin 4: normally open
(NO) switch
1

I047 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-728 40-1347
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-826
Pin 4: normally open
(NO) switch
1

Table 258
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I090 LH external PTO 40-743 40-1410
control
I091 RH external PTO 40-743 40-1410
control
I092 Lights switch [LNK] 40-1410
I093 Top lights switch 40-953 40-1410
I094 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-629 40-1410
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1206
Pin 4: normally open
(NO) switch
1

I095 Engine memory 40-719 40-1410

switch 40-843
I096 2.7659.152.0/10 Differential lock 40-843 40-1410
switch 40-1206

I097 2.7659.350.0 Rear PTO switch 1 40-743 40-1410

2
3

2 220 ohm
1W
1 270 ohm

3 1W

40-396
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I098 2.7659.151.0/20 Dual traction switch 40-843 40-1410
40-1206

I099 2.7659.277.0 Front PTO switch 40-743 40-1410

I100 Rotating beacon 40-1087 40-1410

switch
I101 2.7659.158.0 Hazard warning 40-843 40-1410
0
1
5 17

40-953
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I102 0.015.0485.4 Starter switch 40-629 40-1410

83
50
40-1255
40-1206
30
86s

40-1087
75 15

40-953
Pos
Pin 30 15 50 75 83 40-895
0 40-843
1 40-743
2 40-719
D0010060

I103 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-743 40-1410
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-843
Pin 4: normally open
(NO) switch
1

I104 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-743 40-1410
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-843
Pin 4: normally open
(NO) switch
1

40-397
 Wiring diagrams
Table 259
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-677 40-1301
switch
I106 2.7659.152.0/10 Differential lock 40-826 40-1347
switch 40-1186

I108 2.7659.151.0/20 Dual traction switch 40-826 40-1347

40-1186

I112 Corner work light [LNK] 40-1410

switches
I114 2.7659.156.0 Low work lights 0
1
40-992 40-1347
switch 7

8
40-1042
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I116 2.7659.157.0 Low work lights 40-1087 40-1410

switch

I118 Corner work lights 40-992 40-1347

switch 40-1042
I119 Corner work lights 40-1087 40-1410
switch

40.2.46 - I - Circuit breakers (AGROFARM 420 -> ZKDW390200TD25001)

ITA version
Table 260
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1024 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1024 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I003 2.7659.159.0 Rotating beacon 0

1
40-1024 40-1301
switch 7

8
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

40-398
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I004 2.7659.224.0/10 Windscreen wiper 40-750 40-1301
switch

I005 2.7659.192.0/10 Rear screen wiper 40-750 40-1301

switch

I006 2.7659.223.0/10 Windscreen washer 40-750 40-1301

button

I007 2.7659.343.0/10 Start enable switch 40-596 40-1306

(transmission in neu- 40-1166
tral) 40-621
40-807
40-1145
3,9 Ohm

I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
SYNCRO Pin 2: Normally 40-807
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-791
CB A

I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
ECO Pin 2: Normally 40-807
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-791
CB A

I010 2.7659.079.0 Rear work light 0

40-976 40-1318
switch
1

Pin 1 2
Pos

I011 2.7659.091.0 Rear screen wiper 0

40-758 40-1318
switch
1
3

1
2
4

Pin 1 2
Pos

40-399
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I012 2.7659.146.0 Windscreen washer 1
0
40-758 40-1318
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

I013 2.7659.126.0 Rotating beacon 0

40-976 40-1318
switch
1

Pin 1 2
Pos

I014 2.7659.092.0 Windscreen wiper 1

0
40-758 40-1318
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I015 2.7659.078.0 Front work lights 0

40-976 40-1318
switch
1

Pin 1 2
Pos

I016 2.7659.126.0 Rotating beacon 0

40-976 40-1388
switch
1

Pin 1 2
Pos

I017 2.7659.092.0 Windscreen wiper 1

0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I018 2.7659.091.0 Rear screen wiper 0

[LNK] 40-1388
switch
1
3

1
2
4

Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-976 40-1388
switch
1

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-976 40-1388
switch
1

Pin 1 2
Pos

40-400
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I021 2.7659.146.0 Windscreen washer 1
0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

I022 2.7659.177.0/20 Front PTO switch Resistance between 40-723 40-1331

Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I023 LH external PTO 40-723 40-1331
control
I024 RH external PTO 40-723 40-1331
control
I025 Lights switch 40-915 40-1331
I026 Top lights switch 40-915 40-1331
I027 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-596 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1145
Pin 4: normally open
(NO) switch
1

I028 Engine memory 40-701 40-1331

switch
I029 Brake lights switch 40-877 40-1331
I030 Corner work lights 40-976 40-1331
control switch 40-1024
I031 2.7659.152.0/10 Differential lock 40-791 40-1331
switch 40-1145

I032 2.7659.350.0 Rear PTO switch 1 40-723 40-1331

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I033 2.7659.151.0/20 Dual traction switch 40-791 40-1331

40-1145

I034 2.7659.158.0 Hazard warning 40-915 40-1331

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

40-401
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I035 0.015.0485.4 Starter switch 40-596 40-1331
83
50
40-1247
40-1237
30
86s

40-1145
75 15

40-1024
Pos
Pin 30 15 50 75 83 40-976
0 40-915
1 40-877
2 40-791
D0010060 40-758
40-755
40-750
40-723
40-701
40-665
40-671
40-641
40-637
Table 261
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I036 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-723 40-1331
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-791
Pin 4: normally open
(NO) switch
1

I037 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-723 40-1331
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-791
Pin 4: normally open
(NO) switch
1

I048 Auxiliary distributor 40-1237 40-1364

control switch
I059 2.7659.156.0 Low work lights 0
1
40-976 40-1331
switch 7

8
40-1024
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

Table 262
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I075 LH external PTO 40-738 40-1392
control
I076 RH external PTO 40-738 40-1392
control
I077 Lights switch 40-942 40-1392
I078 Top lights switch 40-942 40-1392

40-402
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I079 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-621 40-1392
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1166
Pin 4: normally open
(NO) switch
1

I080 Brake lights switch 40-889 40-1392

I081 Engine memory 40-714 40-1392
switch
I082 2.7659.152.0/10 Differential lock 40-807 40-1392
switch 40-1166

I083 2.7659.350.0 Rear PTO switch 1 40-738 40-1392

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I084 2.7659.151.0/20 Dual traction switch 40-807 40-1392

40-1166

I085 2.7659.277.0 Front PTO switch 40-738 40-1392

I086 2.7659.158.0 Hazard warning 40-942 40-1392

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I087 0.015.0485.4 Starter switch 40-621 40-1392

83
50
40-1255
40-1166
30
86s

40-1076
75 15

40-942
Pos
Pin 30 15 50 75 83 40-889
0 40-807
1 40-738
2 40-714
D0010060

40-403
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I088 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-738 40-1392
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-807
Pin 4: normally open
(NO) switch
1

I089 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-738 40-1392
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-807
Pin 4: normally open
(NO) switch
1

Table 263
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-671 40-1301
switch
I110 Rotating beacon 40-1076 40-1392
switch
I111 Corner work light 40-1076 40-1392
switches
I115 2.7659.157.0 Low work lights 40-1076 40-1392
switch

USA version
Table 264
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1042 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1042 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I003 2.7659.159.0 Rotating beacon 0

1
40-1042 40-1301
switch 7

8
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

40-404
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I004 2.7659.224.0/10 Windscreen wiper 40-764 40-1301
switch

I005 2.7659.192.0/10 Rear screen wiper 40-764 40-1301

switch

I006 2.7659.223.0/10 Windscreen washer 40-764 40-1301

button

I007 2.7659.343.0/10 Start enable switch 40-604 40-1306

(transmission in neu- 40-1206
tral) 40-629
40-843
40-1186
3,9 Ohm

I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
SYNCRO Pin 2: Normally 40-843
closed (NC) contact
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-826
CB A

I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
ECO Pin 2: Normally 40-843
closed (NC) contact
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-826
CB A

I010 2.7659.079.0 Rear work light 0

40-992 40-1318
switch
1

Pin 1 2
Pos

I011 2.7659.091.0 Rear screen wiper 0

40-772 40-1318
switch
1
3

1
2
4

Pin 1 2
Pos

40-405
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I012 2.7659.146.0 Windscreen washer 1
0
40-772 40-1318
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

I013 2.7659.126.0 Rotating beacon 0

40-992 40-1318
switch
1

Pin 1 2
Pos

I014 2.7659.092.0 Windscreen wiper 1

0
40-772 40-1318
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I015 2.7659.078.0 Front work lights 0

40-992 40-1318
switch
1

Pin 1 2
Pos

I016 2.7659.126.0 Rotating beacon 0

40-992 40-1388
switch
1

Pin 1 2
Pos

I017 2.7659.092.0 Windscreen wiper 1

0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I018 2.7659.091.0 Rear screen wiper 0

[LNK] 40-1388
switch
1
3

1
2
4

Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-992 40-1388
switch
1

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-992 40-1388
switch
1

Pin 1 2
Pos

40-406
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I021 2.7659.146.0 Windscreen washer 1
0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

Table 265
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I038 2.7659.158.0 Hazard warning 40-826 40-1347
0
1
5 17

40-928
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I039 2.7659.177.0/20 Front PTO switch Resistance between 40-728 40-1347

Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I040 2.7659.350.0 Rear PTO switch 1 40-728 40-1347
2
3

2 220 ohm
1W
1 270 ohm

3 1W

I041 Lights switch 40-928 40-1347

I042 Top lights switch 40-928 40-1347
I043 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-604 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1186
Pin 4: normally open
(NO) switch
1

I044 Engine memory 40-705 40-1347

switch 40-826
I045 0.015.0485.4 Starter switch 40-604 40-1347
83
50
40-1247
40-1240
30
86s

40-1186
75 15

40-1042
Pos
Pin 30 15 50 75 83 40-992
0 40-928
1 40-882
2 40-826
D0010060 40-769
40-772
40-764
40-728
40-705
40-683
40-677
40-647
40-652

40-407
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I046 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-728 40-1347
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-826
Pin 4: normally open
(NO) switch
1

I047 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-728 40-1347
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-826
Pin 4: normally open
(NO) switch
1

I048 Auxiliary distributor 40-1240 40-1364

control switch
Table 266
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I090 LH external PTO 40-743 40-1410
control
I091 RH external PTO 40-743 40-1410
control
I092 Lights switch [LNK] 40-1410
I093 Top lights switch 40-953 40-1410
I094 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-629 40-1410
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1206
Pin 4: normally open
(NO) switch
1

I095 Engine memory 40-719 40-1410

switch 40-843
I096 2.7659.152.0/10 Differential lock 40-843 40-1410
switch 40-1206

I097 2.7659.350.0 Rear PTO switch 1 40-743 40-1410

2
3

2 220 ohm
1W
1 270 ohm

3 1W

40-408
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I098 2.7659.151.0/20 Dual traction switch 40-843 40-1410
40-1206

I099 2.7659.277.0 Front PTO switch 40-743 40-1410

I100 Rotating beacon 40-1087 40-1410

switch
I101 2.7659.158.0 Hazard warning 40-843 40-1410
0
1
5 17

40-953
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I102 0.015.0485.4 Starter switch 40-629 40-1410

83
50
40-1255
40-1206
30
86s

40-1087
75 15

40-953
Pos
Pin 30 15 50 75 83 40-895
0 40-843
1 40-743
2 40-719
D0010060

I103 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-743 40-1410
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-843
Pin 4: normally open
(NO) switch
1

I104 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-743 40-1410
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-843
Pin 4: normally open
(NO) switch
1

40-409
 Wiring diagrams
Table 267
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-677 40-1301
switch
I106 2.7659.152.0/10 Differential lock 40-826 40-1347
switch 40-1186

I108 2.7659.151.0/20 Dual traction switch 40-826 40-1347

40-1186

I112 Corner work light [LNK] 40-1410

switches
I114 2.7659.156.0 Low work lights 0
1
40-992 40-1347
switch 7

8
40-1042
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I116 2.7659.157.0 Low work lights 40-1087 40-1410

switch

I118 Corner work lights 40-992 40-1347

switch 40-1042
I119 Corner work lights 40-1087 40-1410
switch

40.2.47 - I - Circuit breakers (AGROFARM 430 -> ZKDW430200TD25001)

ITA version
Table 268
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1024 40-1301
40-1059
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1024 40-1301
40-1059
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I003 2.7659.159.0 Rotating beacon 0

1
40-1024 40-1301
switch 7

8
40-1059
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

40-410
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I004 2.7659.224.0/10 Windscreen wiper 40-750 40-1301
switch 40-778

I005 2.7659.192.0/10 Rear screen wiper 40-750 40-1301

switch 40-778

I006 2.7659.223.0/10 Windscreen washer 40-750 40-1301

button 40-778

I007 2.7659.343.0/10 Start enable switch 40-596 40-1306

(transmission in neu- 40-1166
tral) 40-621
40-807
40-1145
3,9 Ohm

I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
SYNCRO Pin 2: Normally 40-807
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-791
CB A

I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
ECO Pin 2: Normally 40-807
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-791
CB A

I010 2.7659.079.0 Rear work light 0

40-976 40-1318
switch
1

Pin 1 2
Pos

I011 2.7659.091.0 Rear screen wiper 0

40-758 40-1318
switch
1
3

1
2
4

Pin 1 2
Pos

40-411
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I012 2.7659.146.0 Windscreen washer 1
0
40-758 40-1318
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

I013 2.7659.126.0 Rotating beacon 0

40-976 40-1318
switch
1

Pin 1 2
Pos

I014 2.7659.092.0 Windscreen wiper 1

0
40-758 40-1318
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I015 2.7659.078.0 Front work lights 0

40-976 40-1318
switch
1

Pin 1 2
Pos

I016 2.7659.126.0 Rotating beacon 0

40-976 40-1388
switch
1

1
40-1008
2

Pin 1 2
Pos

I017 2.7659.092.0 Windscreen wiper 1

0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I018 2.7659.091.0 Rear screen wiper 0

[LNK] 40-1388
switch
1
3

1
2
4

Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-976 40-1388
switch
1

1
40-1008
2

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-976 40-1388
switch
1

1
40-1008
2

Pin 1 2
Pos

40-412
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I021 2.7659.146.0 Windscreen washer 1
0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

I022 2.7659.177.0/20 Front PTO switch Resistance between 40-723 40-1331

Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I023 LH external PTO 40-723 40-1331
control
I024 RH external PTO 40-723 40-1331
control
I025 Lights switch 40-915 40-1331
I026 Top lights switch 40-915 40-1331
I027 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-596 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1145
Pin 4: normally open
(NO) switch
1

I028 Engine memory 40-701 40-1331

switch
I029 Brake lights switch 40-877 40-1331
I030 Corner work lights 40-976 40-1331
control switch 40-1024
I031 2.7659.152.0/10 Differential lock 40-791 40-1331
switch 40-1145

I032 2.7659.350.0 Rear PTO switch 1 40-723 40-1331

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I033 2.7659.151.0/20 Dual traction switch 40-791 40-1331

40-1145

I034 2.7659.158.0 Hazard warning 40-915 40-1331

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

40-413
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I035 0.015.0485.4 Starter switch 40-596 40-1331
83
50
40-1247
40-1237
30
86s

40-1145
75 15

40-1024
Pos
Pin 30 15 50 75 83 40-976
0 40-915
1 40-877
2 40-791
D0010060 40-758
40-755
40-750
40-723
40-701
40-665
40-671
40-641
40-637
Table 269
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I036 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-723 40-1331
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-791
Pin 4: normally open
(NO) switch
1

I037 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-723 40-1331
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-791
Pin 4: normally open
(NO) switch
1

I048 Auxiliary distributor 40-1237 40-1364

control switch 40-1243
I049 LH external PTO 40-734 40-1365
control
I050 RH external PTO 40-734 40-1365
control
I051 Lights switch 40-964 40-1365
I052 Top lights switch 40-964 40-1365
I053 External lift up con- 40-1269 40-1365
trol switch
I054 External lift up con- 40-1269 40-1365
trol switch
I055 External lift down 40-1269 40-1365
control switch
I056 External lift down 40-1269 40-1365
control switch

40-414
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I057 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-613 40-1365
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1226
Pin 4: normally open
(NO) switch
1

I058 Engine memory 40-710 40-1365

switch 40-862
I059 2.7659.156.0 Low work lights 0
1
40-976 40-1331
switch 7

8
40-1024
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I060 2.7659.158.0 Hazard warning 40-964 40-1365

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I061 0.015.0485.4 Starter switch 40-613 40-1365

40-1269 83
50

40-1262
30
86s

40-1243
75 15

40-1226
Pos
Pin 30 15 50 75 83
40-1059
0 40-1008
1 40-964
2 40-902
40-862 D0010060

40-787
40-783
40-778
40-734
40-710
40-689
40-695
40-657
40-660
I062 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-734 40-1365
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-862
Pin 4: normally open
(NO) switch
1

I063 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-734 40-1365
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-862
Pin 4: normally open
(NO) switch
1

40-415
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I064 Start enable switch 40-613 40-1385
(transmission in neu- 40-1226
tral)
I065 PTO engage switch 40-734 40-1385
ECO 40-862
I066 PTO engage switch 40-734 40-1385
SYNCRO 40-862
I067 2.7659.362.0 Engine memory 40-710 40-1386
switch
I068 2.7659.364.0 Lift switch [LNK] 40-1386
I069 Lift control [LNK] 40-1386
I070 2.7659.363.0 Rear PTO control 40-734 40-1386
switch
Table 270
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I071 2.7659.363.0 Front PTO control 40-734 40-1386
switch
I072 2.7659.363.0 Automatic PTO con- 40-734 40-1386
trol switch
I073 2.7659.362.0 Dual traction control [LNK] 40-1386
switch
I074 2.7659.362.0 Differential lock con- [LNK] 40-1386
trol switch
I075 LH external PTO 40-738 40-1392
control
I076 RH external PTO 40-738 40-1392
control
I077 Lights switch 40-942 40-1392
I078 Top lights switch 40-942 40-1392
I079 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-621 40-1392
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1166
Pin 4: normally open
(NO) switch
1

I080 Brake lights switch 40-889 40-1392

I081 Engine memory 40-714 40-1392
switch
I082 2.7659.152.0/10 Differential lock 40-807 40-1392
switch 40-1166

I083 2.7659.350.0 Rear PTO switch 1 40-738 40-1392

2
3

2 220 ohm
1W
1 270 ohm

3 1W

40-416
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I084 2.7659.151.0/20 Dual traction switch 40-807 40-1392
40-1166

I085 2.7659.277.0 Front PTO switch 40-738 40-1392

I086 2.7659.158.0 Hazard warning 40-942 40-1392

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I087 0.015.0485.4 Starter switch 40-621 40-1392

83
50
40-1255
40-1166
30
86s

40-1076
75 15

40-942
Pos
Pin 30 15 50 75 83 40-889
0 40-807
1 40-738
2 40-714
D0010060

I088 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-738 40-1392
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-807
Pin 4: normally open
(NO) switch
1

I089 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-738 40-1392
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-807
Pin 4: normally open
(NO) switch
1

40-417
 Wiring diagrams
Table 271
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-671 40-1301
switch 40-695
I107 2.7659.156.0 Low work lights 0
1
40-1008 40-1365
switch 7

8
40-1059
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I109 Brake lights switch [LNK] 40-1365

I110 Rotating beacon 40-1076 40-1392
switch
I111 Corner work light 40-1076 40-1392
switches
I115 2.7659.157.0 Low work lights 40-1076 40-1392
switch

I117 Corner work lights 40-1008 40-1365

switch 40-1059

USA version
Table 272
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1042 40-1301
40-1059
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1042 40-1301
40-1059
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I003 2.7659.159.0 Rotating beacon 0

1
40-1042 40-1301
switch 7

8
40-1059
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I004 2.7659.224.0/10 Windscreen wiper 40-764 40-1301

switch 40-778

I005 2.7659.192.0/10 Rear screen wiper 40-764 40-1301

switch 40-778

40-418
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I006 2.7659.223.0/10 Windscreen washer 40-764 40-1301
button 40-778

I007 2.7659.343.0/10 Start enable switch 40-604 40-1306

(transmission in neu- 40-1206
tral) 40-629
40-843
40-1186

3,9 Ohm
I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
SYNCRO Pin 2: Normally 40-843
closed (NC) contact
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-826 CB A

I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
ECO Pin 2: Normally 40-902
closed (NC) contact 40-843
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-826
CB A

I010 2.7659.079.0 Rear work light 0

40-992 40-1318
switch
1

Pin 1 2
Pos

I011 2.7659.091.0 Rear screen wiper 0

40-772 40-1318
switch
1
3

1
2
4

Pin 1 2
Pos

I012 2.7659.146.0 Windscreen washer 1

0
40-772 40-1318
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

I013 2.7659.126.0 Rotating beacon 0

40-992 40-1318
switch
1

Pin 1 2
Pos

40-419
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I014 2.7659.092.0 Windscreen wiper 1
0
40-772 40-1318
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I015 2.7659.078.0 Front work lights 0

40-992 40-1318
switch
1

Pin 1 2
Pos

I016 2.7659.126.0 Rotating beacon 0

40-992 40-1388
switch
1

1
40-1008
2

Pin 1 2
Pos

I017 2.7659.092.0 Windscreen wiper 1

0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I018 2.7659.091.0 Rear screen wiper 0

[LNK] 40-1388
switch
1
3

1
2
4

Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-992 40-1388
switch
1

1
40-1008
2

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-992 40-1388
switch
1

1
40-1008
2

Pin 1 2
Pos

I021 2.7659.146.0 Windscreen washer 1

0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

40-420
Wiring diagrams
Table 273
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I038 2.7659.158.0 Hazard warning 40-826 40-1347
0
1
5 17

40-928
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I039 2.7659.177.0/20 Front PTO switch Resistance between 40-728 40-1347

Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I040 2.7659.350.0 Rear PTO switch 1 40-728 40-1347
2
3

2 220 ohm
1W
1 270 ohm

3 1W

I041 Lights switch 40-928 40-1347

I042 Top lights switch 40-928 40-1347
I043 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-604 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1186
Pin 4: normally open
(NO) switch
1

I044 Engine memory 40-705 40-1347

switch 40-826
I045 0.015.0485.4 Starter switch 40-604 40-1347
83
50
40-1247
40-1240
30
86s

40-1186
75 15

40-1042
Pos
Pin 30 15 50 75 83 40-992
0 40-928
1 40-882
2 40-826
D0010060 40-769
40-772
40-764
40-728
40-705
40-683
40-677
40-647
40-652

40-421
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I046 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-728 40-1347
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-826
Pin 4: normally open
(NO) switch
1

I047 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-728 40-1347
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-826
Pin 4: normally open
(NO) switch
1

I048 Auxiliary distributor 40-1240 40-1364

control switch 40-1243
I049 LH external PTO 40-734 40-1365
control
I050 RH external PTO 40-734 40-1365
control
I051 Lights switch 40-964 40-1365
I052 Top lights switch 40-964 40-1365
I053 External lift up con- 40-1269 40-1365
trol switch
I054 External lift up con- 40-1269 40-1365
trol switch
I055 External lift down 40-1269 40-1365
control switch
I056 External lift down 40-1269 40-1365
control switch
I057 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-613 40-1365
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1226
Pin 4: normally open
(NO) switch
1

I058 Engine memory 40-710 40-1365

switch 40-862
I060 2.7659.158.0 Hazard warning 40-964 40-1365
0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

40-422
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I061 0.015.0485.4 Starter switch 40-613 40-1365
83 40-1269
50

40-1262
30
86s

40-1243
75 15

40-1226
Pos
Pin 30 15 50 75 83
40-1059
0 40-1008
1 40-964
2 40-902
40-862 D0010060

40-787
40-783
40-778
40-734
40-710
40-689
40-695
40-657
40-660
I062 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-734 40-1365
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-862
Pin 4: normally open
(NO) switch
1

I063 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-734 40-1365
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-862
Pin 4: normally open
(NO) switch
1

I064 Start enable switch 40-613 40-1385

(transmission in neu- 40-1226
tral)
I065 PTO engage switch 40-734 40-1385
ECO 40-862
I066 PTO engage switch 40-734 40-1385
SYNCRO 40-862
I067 2.7659.362.0 Engine memory 40-710 40-1386
switch
I068 2.7659.364.0 Lift switch [LNK] 40-1386
I069 Lift control [LNK] 40-1386
I070 2.7659.363.0 Rear PTO control 40-734 40-1386
switch

40-423
 Wiring diagrams
Table 274
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I071 2.7659.363.0 Front PTO control 40-734 40-1386
switch
I072 2.7659.363.0 Automatic PTO con- 40-734 40-1386
trol switch
I073 2.7659.362.0 Dual traction control [LNK] 40-1386
switch
I074 2.7659.362.0 Differential lock con- [LNK] 40-1386
trol switch
I090 LH external PTO 40-743 40-1410
control
I091 RH external PTO 40-743 40-1410
control
I092 Lights switch [LNK] 40-1410
I093 Top lights switch 40-953 40-1410
I094 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-629 40-1410
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1206
Pin 4: normally open
(NO) switch
1

I095 Engine memory 40-719 40-1410

switch 40-843
I096 2.7659.152.0/10 Differential lock 40-843 40-1410
switch 40-1206

I097 2.7659.350.0 Rear PTO switch 1 40-743 40-1410

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I098 2.7659.151.0/20 Dual traction switch 40-843 40-1410

40-1206

I099 2.7659.277.0 Front PTO switch 40-743 40-1410

I100 Rotating beacon 40-1087 40-1410

switch
I101 2.7659.158.0 Hazard warning 40-843 40-1410
0
1
5 17

40-953
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

40-424
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I102 0.015.0485.4 Starter switch 40-629 40-1410
83
50
40-1255
40-1206
30
86s

40-1087
75 15

40-953
Pos
Pin 30 15 50 75 83 40-895
0 40-843
1 40-743
2 40-719
D0010060

I103 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-743 40-1410
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-843
Pin 4: normally open
(NO) switch
1

I104 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-743 40-1410
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-843
Pin 4: normally open
(NO) switch
1

Table 275
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-677 40-1301
switch 40-695
I106 2.7659.152.0/10 Differential lock 40-826 40-1347
switch 40-1186

I107 2.7659.156.0 Low work lights 0

1
40-1008 40-1365
switch 7

8
40-1059
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I108 2.7659.151.0/20 Dual traction switch 40-826 40-1347

40-1186

I109 Brake lights switch 40-902 40-1365

I112 Corner work light [LNK] 40-1410
switches
I114 2.7659.156.0 Low work lights 0
1
40-992 40-1347
switch 7

8
40-1042
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

40-425
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I116 2.7659.157.0 Low work lights 40-1087 40-1410
switch

I117 Corner work lights 40-1008 40-1365

switch 40-1059
I118 Corner work lights 40-992 40-1347
switch 40-1042
I119 Corner work lights 40-1087 40-1410
switch

40.2.48 - I - Circuit breakers (AGROFARM 410 -> ZKDW470200TD30001)

ITA version
Table 276
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1033 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1033 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I003 2.7659.159.0 Rotating beacon 0

1
40-1033 40-1301
switch 7

8
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I004 2.7659.224.0/10 Windscreen wiper 40-750 40-1301

switch

I005 2.7659.192.0/10 Rear screen wiper 40-750 40-1301

switch

I006 2.7659.223.0/10 Windscreen washer 40-750 40-1301

button

40-426
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I007 2.7659.343.0/10 Start enable switch 40-600 40-1306
(transmission in neu- 40-1171
tral) 40-625
40-816
40-1151

3,9 Ohm
I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
SYNCRO Pin 2: Normally 40-816
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-799

CB A
I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
ECO Pin 2: Normally 40-816
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-799
CB A

I016 2.7659.126.0 Rotating beacon 0

40-984 40-1388
switch
1

Pin 1 2
Pos

I017 2.7659.092.0 Windscreen wiper 1

0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I018 2.7659.091.0 Rear screen wiper 0

[LNK] 40-1388
switch
1
3

1
2
4

Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-984 40-1388
switch
1

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-984 40-1388
switch
1

Pin 1 2
Pos

40-427
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I021 2.7659.146.0 Windscreen washer 1
0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

I022 2.7659.177.0/20 Front PTO switch Resistance between 40-723 40-1331

Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I023 LH external PTO 40-723 40-1331
control
I024 RH external PTO 40-723 40-1331
control
I025 Lights switch 40-922 40-1331
I026 Top lights switch 40-922 40-1331
I027 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-600 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1151
Pin 4: normally open
(NO) switch
1

I028 Engine memory 40-701 40-1331

switch
I029 Brake lights switch 40-877 40-1331
I030 Corner work lights 40-984 40-1331
control switch 40-1033
I031 2.7659.152.0/10 Differential lock 40-799 40-1331
switch 40-1151

I032 2.7659.350.0 Rear PTO switch 1 40-723 40-1331

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I033 2.7659.151.0/20 Dual traction switch 40-799 40-1331

40-1151

I034 2.7659.158.0 Hazard warning 40-922 40-1331

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

40-428
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I035 0.015.0485.4 Starter switch 40-600 40-1331
83
50
40-1250
40-1237
30
86s

40-1151
75 15

40-1033
Pos
Pin 30 15 50 75 83 40-984
0 40-922
1 40-877
2 40-799
D0010060 40-755
40-750
40-723
40-701
40-665
40-671
40-637
Table 277
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I036 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-723 40-1331
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-799
Pin 4: normally open
(NO) switch
1

I037 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-723 40-1331
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-799
Pin 4: normally open
(NO) switch
1

I059 2.7659.156.0 Low work lights 0

1
40-984 40-1331
switch 7

8
40-1033
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

Table 278
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I075 LH external PTO 40-738 40-1392
control
I076 RH external PTO 40-738 40-1392
control
I077 Lights switch 40-948 40-1392
I078 Top lights switch 40-948 40-1392

40-429
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I079 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-625 40-1392
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1171
Pin 4: normally open
(NO) switch
1

I080 Brake lights switch [LNK] 40-1392

I081 Engine memory 40-714 40-1392
switch
I082 2.7659.152.0/10 Differential lock 40-816 40-1392
switch 40-1171

I083 2.7659.350.0 Rear PTO switch 1 40-738 40-1392

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I084 2.7659.151.0/20 Dual traction switch 40-816 40-1392

40-1171

I085 2.7659.277.0 Front PTO switch 40-738 40-1392

I086 2.7659.158.0 Hazard warning 40-948 40-1392

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I087 0.015.0485.4 Starter switch 40-625 40-1392

83
50
40-1258
40-1171
30
86s

40-1082
75 15

40-948
Pos
Pin 30 15 50 75 83 40-816
0 40-738
1 40-714
2
D0010060

40-430
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I088 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-738 40-1392
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-816
Pin 4: normally open
(NO) switch
1

I089 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-738 40-1392
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-816
Pin 4: normally open
(NO) switch
1

Table 279
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-671 40-1301
switch
I110 Rotating beacon 40-1082 40-1392
switch
I111 Corner work light 40-1082 40-1392
switches
I115 2.7659.157.0 Low work lights 40-1082 40-1392
switch

USA version
Table 280
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1050 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1050 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I003 2.7659.159.0 Rotating beacon 0

1
40-1050 40-1301
switch 7

8
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

40-431
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I004 2.7659.224.0/10 Windscreen wiper 40-764 40-1301
switch

I005 2.7659.192.0/10 Rear screen wiper 40-764 40-1301

switch

I006 2.7659.223.0/10 Windscreen washer 40-764 40-1301

button

I007 2.7659.343.0/10 Start enable switch 40-608 40-1306

(transmission in neu- 40-1211
tral) 40-633
40-852
40-1192
3,9 Ohm

I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
SYNCRO Pin 2: Normally 40-852
closed (NC) contact
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-834
CB A

I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
ECO Pin 2: Normally 40-852
closed (NC) contact
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-834
CB A

I016 2.7659.126.0 Rotating beacon 0

40-1001 40-1388
switch
1

Pin 1 2
Pos

I017 2.7659.092.0 Windscreen wiper 1

0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

40-432
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I018 2.7659.091.0 Rear screen wiper 0
[LNK] 40-1388
switch
1

1
2
4
Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-1001 40-1388
switch
1

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-1001 40-1388
switch
1

Pin 1 2
Pos

I021 2.7659.146.0 Windscreen washer 1

0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

Table 281
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I038 2.7659.158.0 Hazard warning 40-834 40-1347
0
1
5 17

40-935
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I039 2.7659.177.0/20 Front PTO switch Resistance between 40-728 40-1347

Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I040 2.7659.350.0 Rear PTO switch 1 40-728 40-1347
2
3

2 220 ohm
1W
1 270 ohm

3 1W

I041 Lights switch 40-935 40-1347

I042 Top lights switch 40-935 40-1347

40-433
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I043 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-608 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1192
Pin 4: normally open
(NO) switch
1

I044 Engine memory 40-705 40-1347

switch 40-834
I045 0.015.0485.4 Starter switch 40-608 40-1347
83 40-1250
50

40-1240
30
86s

40-1192
75 15

40-1050
Pos
Pin 30 15 50 75 83
40-1001
0 40-935
1 40-882
2 40-834
40-769 D0010060

40-764
40-728
40-705
40-683
40-677
40-647
I046 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-728 40-1347
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-834
Pin 4: normally open
(NO) switch
1

I047 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-728 40-1347
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-834
Pin 4: normally open
(NO) switch
1

40-434
Wiring diagrams
Table 282
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I090 LH external PTO 40-743 40-1410
control
I091 RH external PTO 40-743 40-1410
control
I092 Lights switch [LNK] 40-1410
I093 Top lights switch 40-959 40-1410
I094 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-633 40-1410
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1211
Pin 4: normally open
(NO) switch
1

I095 Engine memory 40-719 40-1410

switch 40-852
I096 2.7659.152.0/10 Differential lock 40-852 40-1410
switch 40-1211

I097 2.7659.350.0 Rear PTO switch 1 40-743 40-1410

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I098 2.7659.151.0/20 Dual traction switch 40-852 40-1410

40-1211

I099 2.7659.277.0 Front PTO switch 40-743 40-1410

I100 Rotating beacon 40-1093 40-1410

switch
I101 2.7659.158.0 Hazard warning 40-852 40-1410
0
1
5 17

40-959
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

40-435
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I102 0.015.0485.4 Starter switch 40-633 40-1410
83
50
40-1258
40-1211
30
86s

40-1093
75 15

40-959
Pos
Pin 30 15 50 75 83 40-852
0 40-743
1 40-719
2
D0010060

I103 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-743 40-1410
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-852
Pin 4: normally open
(NO) switch
1

I104 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-743 40-1410
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-852
Pin 4: normally open
(NO) switch
1

Table 283
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-677 40-1301
switch
I106 2.7659.152.0/10 Differential lock 40-834 40-1347
switch 40-1192

I108 2.7659.151.0/20 Dual traction switch 40-834 40-1347

40-1192

I112 Corner work light [LNK] 40-1410

switches
I114 2.7659.156.0 Low work lights 0
1
40-1001 40-1347
switch 7

8
40-1050
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I116 2.7659.157.0 Low work lights 40-1093 40-1410

switch

40-436
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I118 Corner work lights 40-1001 40-1347
switch 40-1050
I119 Corner work lights 40-1093 40-1410
switch

40.2.49 - I - Circuit breakers (AGROFARM 420 -> ZKDW510200TD30001)

ITA version
Table 284
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1033 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1033 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I003 2.7659.159.0 Rotating beacon 0

1
40-1033 40-1301
switch 7

8
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I004 2.7659.224.0/10 Windscreen wiper 40-750 40-1301

switch

I005 2.7659.192.0/10 Rear screen wiper 40-750 40-1301

switch

I006 2.7659.223.0/10 Windscreen washer 40-750 40-1301

button

I007 2.7659.343.0/10 Start enable switch 40-600 40-1306

(transmission in neu- 40-1178
tral) 40-625
40-816
40-1158
3,9 Ohm

40-437
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
SYNCRO Pin 2: Normally 40-816
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-799

CB A
I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
ECO Pin 2: Normally 40-816
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-799

CB A
I016 2.7659.126.0 Rotating beacon 0
40-984 40-1388
switch
1

Pin 1 2
Pos

I017 2.7659.092.0 Windscreen wiper 1

0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I018 2.7659.091.0 Rear screen wiper 0

[LNK] 40-1388
switch
1
3

1
2
4

Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-984 40-1388
switch
1

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-984 40-1388
switch
1

Pin 1 2
Pos

I021 2.7659.146.0 Windscreen washer 1

0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

40-438
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I022 2.7659.177.0/20 Front PTO switch Resistance between 40-723 40-1331
Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I023 LH external PTO 40-723 40-1331
control
I024 RH external PTO 40-723 40-1331
control
I025 Lights switch 40-922 40-1331
I026 Top lights switch 40-922 40-1331
I027 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-600 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1158
Pin 4: normally open
(NO) switch
1

I028 Engine memory 40-701 40-1331

switch
I029 Brake lights switch 40-877 40-1331
I030 Corner work lights 40-984 40-1331
control switch 40-1033
I031 2.7659.152.0/10 Differential lock 40-799 40-1331
switch 40-1158

I032 2.7659.350.0 Rear PTO switch 1 40-723 40-1331

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I033 2.7659.151.0/20 Dual traction switch 40-799 40-1331

40-1158

I034 2.7659.158.0 Hazard warning 40-922 40-1331

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

40-439
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I035 0.015.0485.4 Starter switch 40-600 40-1331
83
50
40-1250
40-1237
30
86s

40-1158
75 15

40-1033
Pos
Pin 30 15 50 75 83 40-984
0 40-922
1 40-877
2 40-799
D0010060 40-755
40-750
40-723
40-701
40-665
40-671
40-637
Table 285
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I036 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-723 40-1331
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-799
Pin 4: normally open
(NO) switch
1

I037 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-723 40-1331
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-799
Pin 4: normally open
(NO) switch
1

I048 Auxiliary distributor 40-1237 40-1364

control switch
I059 2.7659.156.0 Low work lights 0
1
40-984 40-1331
switch 7

8
40-1033
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

Table 286
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I075 LH external PTO 40-738 40-1392
control
I076 RH external PTO 40-738 40-1392
control
I077 Lights switch 40-948 40-1392
I078 Top lights switch 40-948 40-1392

40-440
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I079 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-625 40-1392
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1178
Pin 4: normally open
(NO) switch
1

I080 Brake lights switch [LNK] 40-1392

I081 Engine memory 40-714 40-1392
switch
I082 2.7659.152.0/10 Differential lock 40-816 40-1392
switch 40-1178

I083 2.7659.350.0 Rear PTO switch 1 40-738 40-1392

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I084 2.7659.151.0/20 Dual traction switch 40-816 40-1392

40-1178

I085 2.7659.277.0 Front PTO switch 40-738 40-1392

I086 2.7659.158.0 Hazard warning 40-948 40-1392

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I087 0.015.0485.4 Starter switch 40-625 40-1392

83
50
40-1258
40-1178
30
86s

40-1082
75 15

40-948
Pos
Pin 30 15 50 75 83 40-816
0 40-738
1 40-714
2
D0010060

40-441
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I088 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-738 40-1392
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-816
Pin 4: normally open
(NO) switch
1

I089 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-738 40-1392
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-816
Pin 4: normally open
(NO) switch
1

Table 287
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-671 40-1301
switch
I110 Rotating beacon 40-1082 40-1392
switch
I111 Corner work light 40-1082 40-1392
switches
I115 2.7659.157.0 Low work lights 40-1082 40-1392
switch

USA version
Table 288
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1050 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1050 40-1301
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I003 2.7659.159.0 Rotating beacon 0

1
40-1050 40-1301
switch 7

8
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

40-442
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I004 2.7659.224.0/10 Windscreen wiper 40-764 40-1301
switch

I005 2.7659.192.0/10 Rear screen wiper 40-764 40-1301

switch

I006 2.7659.223.0/10 Windscreen washer 40-764 40-1301

button

I007 2.7659.343.0/10 Start enable switch 40-608 40-1306

(transmission in neu- 40-1218
tral) 40-633
40-852
40-1199
3,9 Ohm

I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
SYNCRO Pin 2: Normally 40-852
closed (NC) contact
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-834
CB A

I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
ECO Pin 2: Normally 40-852
closed (NC) contact
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-834
CB A

I016 2.7659.126.0 Rotating beacon 0

40-1001 40-1388
switch
1

Pin 1 2
Pos

I017 2.7659.092.0 Windscreen wiper 1

0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

40-443
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I018 2.7659.091.0 Rear screen wiper 0
[LNK] 40-1388
switch
1

1
2
4
Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-1001 40-1388
switch
1

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-1001 40-1388
switch
1

Pin 1 2
Pos

I021 2.7659.146.0 Windscreen washer 1

0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

Table 289
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I038 2.7659.158.0 Hazard warning 40-834 40-1347
0
1
5 17

40-935
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I039 2.7659.177.0/20 Front PTO switch Resistance between 40-728 40-1347

Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I040 2.7659.350.0 Rear PTO switch 1 40-728 40-1347
2
3

2 220 ohm
1W
1 270 ohm

3 1W

I041 Lights switch 40-935 40-1347

I042 Top lights switch 40-935 40-1347

40-444
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I043 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-608 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1199
Pin 4: normally open
(NO) switch
1

I044 Engine memory 40-705 40-1347

switch 40-834
I045 0.015.0485.4 Starter switch 40-608 40-1347
83 40-1250
50

40-1240
30
86s

40-1199
75 15

40-1050
Pos
Pin 30 15 50 75 83
40-1001
0 40-935
1 40-882
2 40-834
40-769 D0010060

40-764
40-728
40-705
40-683
40-677
40-647
I046 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-728 40-1347
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-834
Pin 4: normally open
(NO) switch
1

I047 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-728 40-1347
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-834
Pin 4: normally open
(NO) switch
1

I048 Auxiliary distributor 40-1240 40-1364

control switch

40-445
 Wiring diagrams
Table 290
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I090 LH external PTO 40-743 40-1410
control
I091 RH external PTO 40-743 40-1410
control
I092 Lights switch [LNK] 40-1410
I093 Top lights switch 40-959 40-1410
I094 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-633 40-1410
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1218
Pin 4: normally open
(NO) switch
1

I095 Engine memory 40-719 40-1410

switch 40-852
I096 2.7659.152.0/10 Differential lock 40-852 40-1410
switch 40-1218

I097 2.7659.350.0 Rear PTO switch 1 40-743 40-1410

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I098 2.7659.151.0/20 Dual traction switch 40-852 40-1410

40-1218

I099 2.7659.277.0 Front PTO switch 40-743 40-1410

I100 Rotating beacon 40-1093 40-1410

switch
I101 2.7659.158.0 Hazard warning 40-852 40-1410
0
1
5 17

40-959
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

40-446
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I102 0.015.0485.4 Starter switch 40-633 40-1410
83
50
40-1258
40-1218
30
86s

40-1093
75 15

40-959
Pos
Pin 30 15 50 75 83 40-852
0 40-743
1 40-719
2
D0010060

I103 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-743 40-1410
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-852
Pin 4: normally open
(NO) switch
1

I104 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-743 40-1410
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-852
Pin 4: normally open
(NO) switch
1

Table 291
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-677 40-1301
switch
I106 2.7659.152.0/10 Differential lock 40-834 40-1347
switch 40-1199

I108 2.7659.151.0/20 Dual traction switch 40-834 40-1347

40-1199

I112 Corner work light [LNK] 40-1410

switches
I114 2.7659.156.0 Low work lights 0
1
40-1001 40-1347
switch 7

8
40-1050
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I116 2.7659.157.0 Low work lights 40-1093 40-1410

switch

40-447
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I118 Corner work lights 40-1001 40-1347
switch 40-1050
I119 Corner work lights 40-1093 40-1410
switch

40.2.50 - I - Circuit breakers (AGROFARM 430 -> ZKDW550200TD30001)

ITA version
Table 292
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1033 40-1301
40-1067
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1033 40-1301
40-1067
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I003 2.7659.159.0 Rotating beacon 0

1
40-1033 40-1301
switch 7

8
40-1067
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I004 2.7659.224.0/10 Windscreen wiper 40-750 40-1301

switch 40-778

I005 2.7659.192.0/10 Rear screen wiper 40-750 40-1301

switch 40-778

I006 2.7659.223.0/10 Windscreen washer 40-750 40-1301

button 40-778

I007 2.7659.343.0/10 Start enable switch 40-600 40-1306

(transmission in neu- 40-1158
tral)
3,9 Ohm

40-448
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
SYNCRO Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-799

CB A
I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-723 40-1306
ECO Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-738
Pin 3: Normally open
(NO) contact
40-799

CB A
I016 2.7659.126.0 Rotating beacon 0
40-984 40-1388
switch
1

1
40-1016
2

Pin 1 2
Pos

I017 2.7659.092.0 Windscreen wiper 1

0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I018 2.7659.091.0 Rear screen wiper 0

[LNK] 40-1388
switch
1
3

1
2
4

Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-984 40-1388
switch
1

1
40-1016
2

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-984 40-1388
switch
1

1
40-1016
2

Pin 1 2
Pos

I021 2.7659.146.0 Windscreen washer 1

0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

40-449
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I022 2.7659.177.0/20 Front PTO switch Resistance between 40-723 40-1331
Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I023 LH external PTO 40-723 40-1331
control
I024 RH external PTO 40-723 40-1331
control
I025 Lights switch 40-922 40-1331
I026 Top lights switch 40-922 40-1331
I027 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-600 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1158
Pin 4: normally open
(NO) switch
1

I028 Engine memory 40-701 40-1331

switch
I029 Brake lights switch 40-877 40-1331
I030 Corner work lights 40-984 40-1331
control switch 40-1033
I031 2.7659.152.0/10 Differential lock 40-799 40-1331
switch 40-1158

I032 2.7659.350.0 Rear PTO switch 1 40-723 40-1331

2
3

2 220 ohm
1W
1 270 ohm

3 1W

I033 2.7659.151.0/20 Dual traction switch 40-799 40-1331

40-1158

I034 2.7659.158.0 Hazard warning 40-922 40-1331

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

40-450
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I035 0.015.0485.4 Starter switch 40-600 40-1331
83
50
40-1250
40-1237
30
86s

40-1158
75 15

40-1033
Pos
Pin 30 15 50 75 83 40-984
0 40-922
1 40-877
2 40-799
D0010060 40-755
40-750
40-723
40-701
40-665
40-671
40-637
Table 293
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I036 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-723 40-1331
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-799
Pin 4: normally open
(NO) switch
1

I037 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-723 40-1331
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-799
Pin 4: normally open
(NO) switch
1

I048 Auxiliary distributor 40-1237 40-1364

control switch 40-1243
I049 LH external PTO 40-734 40-1365
control
I050 RH external PTO 40-734 40-1365
control
I051 Lights switch 40-970 40-1365
I052 Top lights switch 40-970 40-1365
I053 External lift up con- 40-1269 40-1365
trol switch
I054 External lift up con- 40-1269 40-1365
trol switch
I055 External lift down 40-1269 40-1365
control switch
I056 External lift down 40-1269 40-1365
control switch

40-451
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I057 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-616 40-1365
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1231
Pin 4: normally open
(NO) switch
1

I058 Engine memory 40-710 40-1365

switch 40-870
I059 2.7659.156.0 Low work lights 0
1
40-984 40-1331
switch 7

8
40-1033
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I060 2.7659.158.0 Hazard warning 40-970 40-1365

0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I061 0.015.0485.4 Starter switch 40-616 40-1365

40-1269 83
50

40-1266
30
86s

40-1243
75 15

40-1231
Pos
Pin 30 15 50 75 83
40-1067
0 40-1016
1 40-970
2 40-902
40-870 D0010060

40-783
40-778
40-734
40-710
40-689
40-695
40-657
I062 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-734 40-1365
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-870
Pin 4: normally open
(NO) switch
1

I063 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-734 40-1365
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-870
Pin 4: normally open
(NO) switch
1

40-452
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I064 Start enable switch 40-616 40-1385
(transmission in neu- 40-1231
tral)
I065 PTO engage switch 40-734 40-1385
ECO 40-870
I066 PTO engage switch 40-734 40-1385
SYNCRO 40-870
I067 2.7659.362.0 Engine memory 40-710 40-1386
switch
I068 2.7659.364.0 Lift switch [LNK] 40-1386
I069 Lift control [LNK] 40-1386
I070 2.7659.363.0 Rear PTO control 40-734 40-1386
switch
Table 294
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I071 2.7659.363.0 Front PTO control 40-734 40-1386
switch
I072 2.7659.363.0 Automatic PTO con- 40-734 40-1386
trol switch
I073 2.7659.362.0 Dual traction control [LNK] 40-1386
switch
I074 2.7659.362.0 Differential lock con- [LNK] 40-1386
trol switch
Table 295
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-671 40-1301
switch 40-695
I107 2.7659.156.0 Low work lights 0
1
40-1016 40-1365
switch 7

8
40-1067
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I109 Brake lights switch [LNK] 40-1365

I117 Corner work lights 40-1016 40-1365
switch 40-1067

USA version
Table 296
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I001 2.7659.154.0 Front work lights 0
40-1050 40-1301
40-1067
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

I002 2.7659.155.0 Rear work lights 0

40-1050 40-1301
40-1067
1
switch
7 4 5 6 3 2 1 8

Pin 1 2 3 4 5 6 7 8
Pos

40-453
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I003 2.7659.159.0 Rotating beacon 0
1
40-1050 40-1301
switch 7

8
40-1067
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I004 2.7659.224.0/10 Windscreen wiper 40-764 40-1301

switch 40-778

I005 2.7659.192.0/10 Rear screen wiper 40-764 40-1301

switch 40-778

I006 2.7659.223.0/10 Windscreen washer 40-764 40-1301

button 40-778

I007 2.7659.343.0/10 Start enable switch 40-608 40-1306

(transmission in neu- 40-1199
tral)
3,9 Ohm

I008 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
SYNCRO Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-826
CB A

I009 2.7659.096.0/10 PTO engage switch Between Pin 1 and 40-728 40-1306
ECO Pin 2: Normally 40-902
closed (NC) contact
Between Pin 2 and 40-743
Pin 3: Normally open
(NO) contact
40-826
CB A

I016 2.7659.126.0 Rotating beacon 0

40-1001 40-1388
switch
1

1
40-1016
2

Pin 1 2
Pos

40-454
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I017 2.7659.092.0 Windscreen wiper 1
0
[LNK] 40-1388
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I018 2.7659.091.0 Rear screen wiper 0

[LNK] 40-1388
switch
1

1
2
4
Pin 1 2
Pos

I019 2.7659.079.0 Rear work light 0

40-1001 40-1388
switch
1

1
40-1016
2

Pin 1 2
Pos

I020 2.7659.078.0 Front work lights 0

40-1001 40-1388
switch
1

1
40-1016
2

Pin 1 2
Pos

I021 2.7659.146.0 Windscreen washer 1

0
[LNK] 40-1388
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

40-455
 Wiring diagrams
Table 297
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I038 2.7659.158.0 Hazard warning 40-826 40-1347
0
1
5 17

40-935
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I039 2.7659.177.0/20 Front PTO switch Resistance between 40-728 40-1347

Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I040 2.7659.350.0 Rear PTO switch 1 40-728 40-1347
2
3

2 220 ohm
1W
1 270 ohm

3 1W

I041 Lights switch 40-935 40-1347

I042 Top lights switch 40-935 40-1347
I043 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-608 40-1331
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1199
Pin 4: normally open
(NO) switch
1

I044 Engine memory 40-705 40-1347

switch 40-826
I045 0.015.0485.4 Starter switch 40-608 40-1347
40-1250
83
50

40-1240
30
86s

40-1199
75 15

40-1050
Pos
Pin 30 15 50 75 83
40-1001
0 40-935
1 40-882
2 40-826
40-769 D0010060

40-764
40-728
40-705
40-683
40-677
40-647
I046 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-728 40-1347
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-826
Pin 4: normally open
(NO) switch
1

40-456
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I047 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-728 40-1347
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-826
Pin 4: normally open
(NO) switch
1

I048 Auxiliary distributor 40-1240 40-1364

control switch 40-1243
I049 LH external PTO 40-734 40-1365
control
I050 RH external PTO 40-734 40-1365
control
I051 Lights switch 40-970 40-1365
I052 Top lights switch 40-970 40-1365
I053 External lift up con- 40-1269 40-1365
trol switch
I054 External lift up con- 40-1269 40-1365
trol switch
I055 External lift down 40-1269 40-1365
control switch
I056 External lift down 40-1269 40-1365
control switch
I057 2.7659.097.0 Clutch engage-dis- Between Pin 1 and 40-616 40-1365
engage control Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1231
Pin 4: normally open
(NO) switch
1

I058 Engine memory 40-710 40-1365

switch 40-870
I060 2.7659.158.0 Hazard warning 40-970 40-1365
0
1
5 17
18

lights switch
10
8 1 2 3
5 1 7 18

Pin 1 2 3 5 8 10 17 18
Pos

I061 0.015.0485.4 Starter switch 40-616 40-1365

83
50
40-1269
40-1266
30
86s

40-1243
75 15

40-1231
Pos
Pin 30 15 50 75 83 40-1067
0 40-1016
1 40-970
2 40-902
D0010060 40-870
40-783
40-778
40-734
40-710
40-689
40-695
40-657

40-457
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I062 2.7659.097.0 1,000 rpm PTO Between Pin 1 and 40-734 40-1365
switch Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-870
Pin 4: normally open
(NO) switch
1

I063 2.7659.097.0 540 rpm PTO switch Between Pin 1 and 40-734 40-1365
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-870
Pin 4: normally open
(NO) switch
1

I064 Start enable switch 40-616 40-1385

(transmission in neu- 40-1231
tral)
I065 PTO engage switch 40-734 40-1385
ECO 40-870
I066 PTO engage switch 40-734 40-1385
SYNCRO 40-870
I067 2.7659.362.0 Engine memory 40-710 40-1386
switch
I068 2.7659.364.0 Lift switch [LNK] 40-1386
I069 Lift control [LNK] 40-1386
I070 2.7659.363.0 Rear PTO control 40-734 40-1386
switch

40-458
Wiring diagrams
Table 298
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I071 2.7659.363.0 Front PTO control 40-734 40-1386
switch
I072 2.7659.363.0 Automatic PTO con- 40-734 40-1386
trol switch
I073 2.7659.362.0 Dual traction control [LNK] 40-1386
switch
I074 2.7659.362.0 Differential lock con- [LNK] 40-1386
trol switch
Table 299
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
I105 Air conditioning 40-677 40-1301
switch 40-695
I106 2.7659.152.0/10 Differential lock 40-826 40-1347
switch 40-1199

I107 2.7659.156.0 Low work lights 0

1
40-1016 40-1365
switch 7

8
40-1067
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I108 2.7659.151.0/20 Dual traction switch 40-826 40-1347

40-1199

I109 Brake lights switch 40-902 40-1365

I114 2.7659.156.0 Low work lights 0
1
40-1001 40-1347
switch 7

8
40-1050
2 3
7 4 5 6

Pin 1 2 3 4 5 6 7 8
Pos

I117 Corner work lights 40-1016 40-1365

switch 40-1067
I118 Corner work lights 40-1001 40-1347
switch 40-1050

40-459
 Wiring diagrams
40.2.51 - J - Relays (AGROFARM 410 -> ZKDW350200TD25001)
ITA version

Ja007 Ja008

Ja001 Ja002 Ja003

Ja004 Ja005 Ja006

Fig. 1096 - Cab fuse box

l Ja001 Key-on power relay for fuses F14-15
l Ja002 - Hi-Lo relay
l Ja003 - Key-on power relay for fuses F11-12-13
l Ja004 - Key-on power relay for fuses F5-6-7-8
l Ja005 - Trailer relay
l Ja006 - Fan relay
l Ja007 - Starter relay
l Ja008 - Fan/compressor relay (key-on power)

40-460
Wiring diagrams

Jd007 Jd008

Jd001 Jd002 Jd003

Jd004 Jd005 Jd006

Fig. 1097 - Fuse box, ITA platform version

l Jd001 - Key-on power relay for fuses F14-15
l Jd002 - Hi-Lo relay
l Jd003 - Key-on power relay for fuses F11-12-13
l Jd004 - Key-on power relay for fuses F5-6-7-8
l Jd005 - Trailer relay
l Jd006 - Fan relay
l Jd007 - Starter relay
l Jd008 - Fan/compressor relay (key-on power)
Table 300
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-665 40-1308
exchanger fan con- 40-671
trol relay
J002 Auxiliary air condi- 40-665 40-1308
tioner heat exchang- 40-671
er fan control relay
J003 Preheating relay 40-596 40-1324
40-621
40-701
40-714
40-807

40-461
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J004 Preheating relay 40-596 40-1327
40-701
40-621
40-714
40-807
J005 Compressor relay 40-665 40-1275
J006a Preheating relay 40-596 40-1290
40-621
40-701
40-714
J006b Preheating relay 40-596 40-1290
40-621
40-701
40-714
Ja001 Key-on power relay 40-791 40-1331
for fuses F14-15 40-877
40-976
40-1024
40-1145
Ja002 Hi-Lo relay 40-791 40-1331
40-1145
Ja003 Key-on power relay 40-641 40-1331
for fuses F11-12-13 40-665
40-671
40-750
40-755
40-758
40-877
40-915
40-976
40-1024
Ja004 Key-on power relay 40-750 40-1331
for fuses F5-6-7-8 40-755
40-758
40-976
40-1024
Ja005 Trailer relay 40-791 40-1331
40-877
Ja006 Fan relay 40-641 40-1331
40-665
40-671
Ja007 Starter relay 40-596 40-1331
40-701
40-1145
Ja008 Fan/compressor re- 40-641 40-1331
lay (key-on power) 40-665
40-671
Jd001 Key-on power relay 40-807 40-1392
for fuses F14-15 40-889
40-1076
40-1166
Jd002 Hi-Lo relay 40-807 40-1392
40-1166
Jd003 Key-on power relay 40-889 40-1392
for fuses F11-12-13 40-953
Jd004 Key-on power relay [LNK] 40-1392
for fuses F5-6-7-8
Jd005 Trailer relay 40-807 40-1392
40-889
40-1166
Jd006 Fan relay [LNK] 40-1392

40-462
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jd007 Starter relay 40-621 40-1392
40-714
40-1166
Jd008 Fan/compressor re- [LNK] 40-1392
lay (key-on power)
Je001 Max fan speed relay 40-671 40-1301
Je002 Compressor start 40-671 40-1301
relay
Je003 Third fan speed re- 40-671 40-1301
lay
Jf001 Air conditioning relay [LNK] 40-1318

USA version

Jb007 Jb008

Jb001 Jb002 Jb003

Jb004 Jb005 Jb006

Fig. 1098 - Cab fuse box

l Jb001 - Key-on power relay for fuses F14-15
l Jb002 - Hi-Lo relay
l Jb003 - Key-on power relay for fuses F11-12-13
l Jb004 Key-on power relay for fuses F5-6-7-8
l Jb005 - Trailer relay
l Jb006 - Fan relay
l Jb007 - Starter relay
l Jb008 - Fan/compressor relay (key-on power)

40-463
 Wiring diagrams

Jh007 Jh008

Jh001 Jh002 Jh003

Jh004 Jh005 Jh006

Fig. 1099 - Platform fuse box

l Jh001 - Key-on power relay for fuses F14-15
l Jh002 - Hi-Lo relay
l Jh003 - Key-on power relay for fuses F11-12-13
l Jh004 - Key-on power relay for fuses F5-6-7-8
l Jh005 - Trailer relay
l Jh006 - Fan relay
l Jh007 - Starter relay
l Jh008 - Fan/compressor relay (key-on power)
Table 301
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-683 40-1308
exchanger fan con- 40-677
trol relay
J002 Auxiliary air condi- 40-683 40-1308
tioner heat exchang- 40-677
er fan control relay
J003 Preheating relay 40-604 40-1324
40-629
40-705
40-719
40-843

40-464
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J004 Preheating relay 40-604 40-1327
40-705
40-719
40-843
40-629
J005 Compressor relay 40-683 40-1275
J006a Preheating relay 40-604 40-1290
40-629
40-705
40-719
J006b Preheating relay 40-604 40-1290
40-629
40-705
40-719
Jb001 Key-on power relay 40-826 40-1347
for fuses F14-15 40-882
40-992
40-1042
40-1186
Jb002 Hi-Lo relay 40-826 40-1347
40-1186
Jb003 Key-on power relay 40-647 40-1347
for fuses F11-12-13 40-652
40-683
40-677
40-764
40-769
40-772
40-882
40-928
40-992
40-1042
Jb004 Key-on power relay 40-764 40-1347
for fuses F5-6-7-8 40-769
40-772
40-992
40-1042
Jb005 Trailer relay 40-826 40-1347
40-882
40-1186
Jb006 Fan relay 40-647 40-1347
40-652
40-683
40-677
Jb007 Starter relay 40-604 40-1347
40-705
40-1186
Jb008 Fan/compressor re- 40-647 40-1347
lay (key-on power) 40-652
40-683
40-677
Je001 Max fan speed relay 40-677 40-1301
Je002 Compressor start 40-677 40-1301
relay
Je003 Third fan speed re- 40-677 40-1301
lay
Jf001 Air conditioning relay [LNK] 40-1318
Jh001 Key-on power relay 40-843 40-1410
for fuses F14-15 40-895
40-1087
40-1206

40-465
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jh002 Hi-Lo relay 40-843 40-1410
40-1206
Jh003 Key-on power relay 40-895 40-1410
for fuses F11-12-13
Jh004 Key-on power relay [LNK] 40-1410
for fuses F5-6-7-8
Jh005 Trailer relay 40-843 40-1410
40-895
40-1206
Jh006 Fan relay [LNK] 40-1410
Jh007 Starter relay 40-629 40-1410
40-719
40-1206
Jh008 Fan/compressor re- [LNK] 40-1410
lay (key-on power)

40.2.52 - J - Relays (AGROFARM 420 -> ZKDW390200TD25001)

ITA version

Ja007 Ja008

Ja001 Ja002 Ja003

Ja004 Ja005 Ja006

Fig. 1099 - Cab fuse box

l Ja001 Key-on power relay for fuses F14-15
l Ja002 - Hi-Lo relay
l Ja003 - Key-on power relay for fuses F11-12-13

40-466
Wiring diagrams

Ja007 Ja008

Ja001 Ja002 Ja003

Ja004 Ja005 Ja006

Fig. 1099 - Cab fuse box

l Ja004 - Key-on power relay for fuses F5-6-7-8
l Ja005 - Trailer relay
l Ja006 - Fan relay
l Ja007 - Starter relay
l Ja008 - Fan/compressor relay (key-on power)

40-467
 Wiring diagrams

Jd007 Jd008

Jd001 Jd002 Jd003

Jd004 Jd005 Jd006

Fig. 1099 - Fuse box, ITA platform version

l Jd001 - Key-on power relay for fuses F14-15
l Jd002 - Hi-Lo relay
l Jd003 - Key-on power relay for fuses F11-12-13
l Jd004 - Key-on power relay for fuses F5-6-7-8
l Jd005 - Trailer relay
l Jd006 - Fan relay
l Jd007 - Starter relay
l Jd008 - Fan/compressor relay (key-on power)
Table 302
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-665 40-1308
exchanger fan con- 40-671
trol relay
J002 Auxiliary air condi- 40-665 40-1308
tioner heat exchang- 40-671
er fan control relay
J003 Preheating relay 40-596 40-1324
40-621
40-701
40-714
40-807

40-468
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J004 Preheating relay 40-596 40-1327
40-701
40-621
40-714
40-807
J005 Compressor relay 40-665 40-1275
J006a Preheating relay 40-596 40-1290
40-621
40-701
40-714
J006b Preheating relay 40-596 40-1290
40-621
40-701
40-714
Ja001 Key-on power relay 40-791 40-1331
for fuses F14-15 40-877
40-976
40-1024
40-1145
Ja002 Hi-Lo relay 40-791 40-1331
40-1145
Ja003 Key-on power relay 40-641 40-1331
for fuses F11-12-13 40-665
40-671
40-750
40-755
40-758
40-877
40-915
40-976
40-1024
40-1237
Ja004 Key-on power relay 40-750 40-1331
for fuses F5-6-7-8 40-755
40-758
40-976
40-1024
Ja005 Trailer relay 40-791 40-1331
40-877
Ja006 Fan relay 40-641 40-1331
40-665
40-671
Ja007 Starter relay 40-596 40-1331
40-701
40-1145
Ja008 Fan/compressor re- 40-641 40-1331
lay (key-on power) 40-665
40-671
Jd001 Key-on power relay 40-807 40-1392
for fuses F14-15 40-889
40-1076
40-1166
Jd002 Hi-Lo relay 40-807 40-1392
40-1166
Jd003 Key-on power relay 40-889 40-1392
for fuses F11-12-13 40-953
Jd004 Key-on power relay [LNK] 40-1392
for fuses F5-6-7-8
Jd005 Trailer relay 40-807 40-1392
40-889
40-1166

40-469
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jd006 Fan relay [LNK] 40-1392
Jd007 Starter relay 40-621 40-1392
40-714
40-1166
Jd008 Fan/compressor re- [LNK] 40-1392
lay (key-on power)
Je001 Max fan speed relay 40-671 40-1301
Je002 Compressor start 40-671 40-1301
relay
Je003 Third fan speed re- 40-671 40-1301
lay
Jf001 Air conditioning relay [LNK] 40-1318

USA version

Jb007 Jb008

Jb001 Jb002 Jb003

Jb004 Jb005 Jb006

Fig. 1099 - Cab fuse box

l Jb001 - Key-on power relay for fuses F14-15
l Jb002 - Hi-Lo relay
l Jb003 - Key-on power relay for fuses F11-12-13
l Jb004 Key-on power relay for fuses F5-6-7-8
l Jb005 - Trailer relay
l Jb006 - Fan relay
l Jb007 - Starter relay
l Jb008 - Fan/compressor relay (key-on power)

40-470
Wiring diagrams

Jh007 Jh008

Jh001 Jh002 Jh003

Jh004 Jh005 Jh006

Fig. 1099 - Platform fuse box

l Jh001 - Key-on power relay for fuses F14-15
l Jh002 - Hi-Lo relay
l Jh003 - Key-on power relay for fuses F11-12-13
l Jh004 - Key-on power relay for fuses F5-6-7-8
l Jh005 - Trailer relay
l Jh006 - Fan relay
l Jh007 - Starter relay
l Jh008 - Fan/compressor relay (key-on power)
Table 303
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-683 40-1308
exchanger fan con- 40-677
trol relay
J002 Auxiliary air condi- 40-683 40-1308
tioner heat exchang- 40-677
er fan control relay
J003 Preheating relay 40-604 40-1324
40-629
40-705
40-719
40-843

40-471
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J004 Preheating relay 40-604 40-1327
40-705
40-719
40-843
40-629
J005 Compressor relay 40-683 40-1275
J006a Preheating relay 40-604 40-1290
40-629
40-705
40-719
J006b Preheating relay 40-604 40-1290
40-629
40-705
40-719
Jb001 Key-on power relay 40-826 40-1347
for fuses F14-15 40-882
40-992
40-1042
40-1186
Jb002 Hi-Lo relay 40-826 40-1347
40-1186
Jb003 Key-on power relay 40-647 40-1347
for fuses F11-12-13 40-652
40-683
40-677
40-764
40-769
40-772
40-882
40-928
40-992
40-1042
40-1240
Jb004 Key-on power relay 40-764 40-1347
for fuses F5-6-7-8 40-769
40-772
40-992
40-1042
Jb005 Trailer relay 40-826 40-1347
40-882
40-1186
Jb006 Fan relay 40-647 40-1347
40-652
40-683
40-677
Jb007 Starter relay 40-604 40-1347
40-705
40-1186
Jb008 Fan/compressor re- 40-647 40-1347
lay (key-on power) 40-652
40-683
40-677
Je001 Max fan speed relay 40-677 40-1301
Je002 Compressor start 40-677 40-1301
relay
Je003 Third fan speed re- 40-677 40-1301
lay
Jf001 Air conditioning relay [LNK] 40-1318

40-472
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jh001 Key-on power relay 40-843 40-1410
for fuses F14-15 40-895
40-1087
40-1206
Jh002 Hi-Lo relay 40-843 40-1410
40-1206
Jh003 Key-on power relay 40-895 40-1410
for fuses F11-12-13
Jh004 Key-on power relay [LNK] 40-1410
for fuses F5-6-7-8
Jh005 Trailer relay 40-843 40-1410
40-895
40-1206
Jh006 Fan relay [LNK] 40-1410
Jh007 Starter relay 40-629 40-1410
40-719
40-1206
Jh008 Fan/compressor re- [LNK] 40-1410
lay (key-on power)

40.2.53 - J - Relays (AGROFARM 430 -> ZKDW430200TD25001)

ITA version

Ja007 Ja008

Ja001 Ja002 Ja003

Ja004 Ja005 Ja006

Fig. 1100 - Cab fuse box

40-473
 Wiring diagrams
l Ja001 Key-on power relay for fuses F14-15
l Ja002 - Hi-Lo relay
l Ja003 - Key-on power relay for fuses F11-12-13
l Ja004 - Key-on power relay for fuses F5-6-7-8
l Ja005 - Trailer relay
l Ja006 - Fan relay
l Ja007 - Starter relay
l Ja008 - Fan/compressor relay (key-on power)

Jc007 Jc008

Jc001 Jc002 Jc003

Jc004 Jc005 Jc006

Fig. 1101 - Cab fuse box, version with electronic lift

l Jc001 - Key-on power relay for fuses F14-15
l Jc002 - Hi-Lo relay
l Jc003 - Key-on power relay for fuses F11-12-13
l Jc004 - Key-on power relay for fuses F5-6-7-8
l Jc006 - Fan relay
l Jc007 - Starter relay
l Ja008 - Fan/compressor relay (key-on power)

40-474
Wiring diagrams

Jd007 Jd008

Jd001 Jd002 Jd003

Jd004 Jd005 Jd006

Fig. 1102 - Platform fuse box

l Jd001 - Key-on power relay for fuses F14-15
l Jd002 - Hi-Lo relay
l Jd003 - Key-on power relay for fuses F11-12-13
l Jd004 - Key-on power relay for fuses F5-6-7-8
l Jd005 - Trailer relay
l Jd006 - Fan relay
l Jd007 - Starter relay
l Jd008 - Fan/compressor relay (key-on power)
Table 304
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-665 40-1308
exchanger fan con- 40-671
trol relay 40-689
40-695
J002 Auxiliary air condi- 40-665 40-1308
tioner heat exchang- 40-671
er fan control relay 40-689
40-695

40-475
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J003 Preheating relay 40-596 40-1324
40-621
40-701
40-714
40-807
40-613
40-710
J004 Preheating relay 40-596 40-1327
40-701
40-621
40-714
40-807
40-613
40-710
J005 Compressor relay 40-665 40-1275
40-689
J006a Preheating relay 40-596 40-1290
40-621
40-701
40-714
40-613
40-710
J006b Preheating relay 40-596 40-1290
40-621
40-701
40-714
40-613
40-710
Ja001 Key-on power relay 40-791 40-1331
for fuses F14-15 40-877
40-976
40-1024
40-1145
Ja002 Hi-Lo relay 40-791 40-1331
40-1145
Ja003 Key-on power relay 40-641 40-1331
for fuses F11-12-13 40-665
40-671
40-750
40-755
40-758
40-877
40-915
40-976
40-1024
40-1237
Ja004 Key-on power relay 40-750 40-1331
for fuses F5-6-7-8 40-755
40-758
40-976
40-1024
Ja005 Trailer relay 40-791 40-1331
40-877
Ja006 Fan relay 40-641 40-1331
40-665
40-671
Ja007 Starter relay 40-596 40-1331
40-701
40-1145
Ja008 Fan/compressor re- 40-641 40-1331
lay (key-on power) 40-665
40-671

40-476
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jc001 Key-on power relay 40-862 40-1365
for fuses F14-15 40-902
40-1008
40-1059
Jc002 Hi-Lo relay 40-862 40-1365
40-1226
Jc003 Key-on power relay 40-689 40-1365
for fuses F11-12-13 40-778
40-783
40-787
40-942
40-1008
40-1059
40-660
40-695
Jc004 Key-on power relay 40-778 40-1365
for fuses F5-6-7-8 40-783
40-787
40-1008
40-1059
Jc005 Trailer relay 40-862 40-1365
40-902
Jc006 Fan relay 40-689 40-1365
40-660
40-695
Jc007 Starter relay 40-613 40-1365
40-710
40-1226
Jc008 Fan/compressor re- 40-689 40-1365
lay (key-on power) 40-660
40-695
Jd001 Key-on power relay 40-807 40-1392
for fuses F14-15 40-889
40-1076
40-1166
Jd002 Hi-Lo relay 40-807 40-1392
40-1166
Jd003 Key-on power relay 40-889 40-1392
for fuses F11-12-13 40-953
Jd004 Key-on power relay [LNK] 40-1392
for fuses F5-6-7-8
Jd005 Trailer relay 40-807 40-1392
40-889
40-1166
Jd006 Fan relay [LNK] 40-1392
Jd007 Starter relay 40-621 40-1392
40-714
40-1166
Jd008 Fan/compressor re- [LNK] 40-1392
lay (key-on power)
Je001 Max fan speed relay 40-671 40-1301
40-695
Je002 Compressor start 40-671 40-1301
relay 40-695
Je003 Third fan speed re- 40-671 40-1301
lay 40-695
Jf001 Air conditioning relay [LNK] 40-1318

40-477
 Wiring diagrams
USA version

Jb007 Jb008

Jb001 Jb002 Jb003

Jb004 Jb005 Jb006

Fig. 1103 - Cab fuse box

l Jb001 - Key-on power relay for fuses F14-15
l Jb002 - Hi-Lo relay
l Jb003 - Key-on power relay for fuses F11-12-13
l Jb004 Key-on power relay for fuses F5-6-7-8
l Jb005 - Trailer relay
l Jb006 - Fan relay
l Jb007 - Starter relay
l Jb008 - Fan/compressor relay (key-on power)

40-478
Wiring diagrams

Jc007 Jc008

Jc001 Jc002 Jc003

Jc004 Jc005 Jc006

Fig. 1103 - Cab fuse box, version with electronic lift

l Jc001 - Key-on power relay for fuses F14-15
l Jc002 - Hi-Lo relay
l Jc003 - Key-on power relay for fuses F11-12-13
l Jc004 - Key-on power relay for fuses F5-6-7-8
l Jc006 - Fan relay
l Jc007 - Starter relay
l Ja008 - Fan/compressor relay (key-on power)

40-479
 Wiring diagrams

Jh007 Jh008

Jh001 Jh002 Jh003

Jh004 Jh005 Jh006

Fig. 1104 - Platform fuse box

l Jh001 - Key-on power relay for fuses F14-15
l Jh002 - Hi-Lo relay
l Jh003 - Key-on power relay for fuses F11-12-13
l Jh004 - Key-on power relay for fuses F5-6-7-8
l Jh005 - Trailer relay
l Jh006 - Fan relay
l Jh007 - Starter relay
l Jh008 - Fan/compressor relay (key-on power)
Table 305
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-683 40-1308
exchanger fan con- 40-677
trol relay 40-689
40-695
J002 Auxiliary air condi- 40-683 40-1308
tioner heat exchang- 40-677
er fan control relay 40-689
40-695

40-480
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J003 Preheating relay 40-604 40-1324
40-629
40-705
40-719
40-843
40-613
40-710
J004 Preheating relay 40-604 40-1327
40-705
40-719
40-843
40-629
40-613
40-710
J005 Compressor relay 40-683 40-1275
40-689
J006a Preheating relay 40-604 40-1290
40-629
40-705
40-719
40-613
40-710
J006b Preheating relay 40-604 40-1290
40-629
40-705
40-719
40-613
40-710
Jb001 Key-on power relay 40-826 40-1347
for fuses F14-15 40-882
40-992
40-1042
40-1186
Jb002 Hi-Lo relay 40-826 40-1347
40-1186
Jb003 Key-on power relay 40-647 40-1347
for fuses F11-12-13 40-652
40-683
40-677
40-764
40-769
40-772
40-882
40-928
40-992
40-1042
40-1240
Jb004 Key-on power relay 40-764 40-1347
for fuses F5-6-7-8 40-769
40-772
40-992
40-1042
Jb005 Trailer relay 40-826 40-1347
40-882
40-1186
Jb006 Fan relay 40-647 40-1347
40-652
40-683
40-677
Jb007 Starter relay 40-604 40-1347
40-705
40-1186

40-481
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jb008 Fan/compressor re- 40-647 40-1347
lay (key-on power) 40-652
40-683
40-677
Jc001 Key-on power relay 40-862 40-1365
for fuses F14-15 40-902
40-1008
40-1059
Jc002 Hi-Lo relay 40-862 40-1365
40-1226
Jc003 Key-on power relay 40-689 40-1365
for fuses F11-12-13 40-778
40-783
40-787
40-942
40-1008
40-1059
40-660
Jc004 Key-on power relay 40-778 40-1365
for fuses F5-6-7-8 40-783
40-787
40-1008
40-1059
Jc005 Trailer relay 40-862 40-1365
40-902
Jc006 Fan relay 40-689 40-1365
40-660
40-695
Jc007 Starter relay 40-613 40-1365
40-710
40-1226
Jc008 Fan/compressor re- 40-689 40-1365
lay (key-on power) 40-660
40-695
Je001 Max fan speed relay 40-677 40-1301
40-695
Je002 Compressor start 40-677 40-1301
relay 40-695
Je003 Third fan speed re- 40-677 40-1301
lay 40-695
Jf001 Air conditioning relay [LNK] 40-1318
Jh001 Key-on power relay 40-843 40-1410
for fuses F14-15 40-895
40-1087
40-1206
Jh002 Hi-Lo relay 40-843 40-1410
40-1206
Jh003 Key-on power relay 40-895 40-1410
for fuses F11-12-13 40-964
Jh004 Key-on power relay [LNK] 40-1410
for fuses F5-6-7-8
Jh005 Trailer relay 40-843 40-1410
40-895
40-1206
Jh006 Fan relay [LNK] 40-1410
Jh007 Starter relay 40-629 40-1410
40-719
40-1206
Jh008 Fan/compressor re- [LNK] 40-1410
lay (key-on power)

40-482
Wiring diagrams
40.2.54 - J - Relays (AGROFARM 410 -> ZKDW470200TD30001)
ITA version

Ja007 Ja008

Ja001 Ja002 Ja003

Ja004 Ja005 Ja006

Fig. 1105 - Cab fuse box

l Ja001 Key-on power relay for fuses F14-15
l Ja002 - Hi-Lo relay
l Ja003 - Key-on power relay for fuses F11-12-13
l Ja004 - Key-on power relay for fuses F5-6-7-8
l Ja005 - Trailer relay
l Ja006 - Fan relay
l Ja007 - Starter relay
l Ja008 - Fan/compressor relay (key-on power)

40-483
 Wiring diagrams

Jd007 Jd008

Jd001 Jd002 Jd003

Jd004 Jd005 Jd006

Fig. 1106 - Fuse box, ITA platform version

l Jd001 - Key-on power relay for fuses F14-15
l Jd002 - Hi-Lo relay
l Jd003 - Key-on power relay for fuses F11-12-13
l Jd004 - Key-on power relay for fuses F5-6-7-8
l Jd005 - Trailer relay
l Jd006 - Fan relay
l Jd007 - Starter relay
l Jd008 - Fan/compressor relay (key-on power)
Table 306
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-665 40-1308
exchanger fan con- 40-671
trol relay
J002 Auxiliary air condi- 40-665 40-1308
tioner heat exchang- 40-671
er fan control relay
J003 Preheating relay 40-600 40-1324
40-625
40-701
40-714
40-816

40-484
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J004 Preheating relay 40-600 40-1327
40-701
40-625
40-714
40-816
J005 Compressor relay 40-665 40-1275
J006a Preheating relay 40-600 40-1290
40-625
40-701
40-714
J006b Preheating relay 40-600 40-1290
40-625
40-701
40-714
Ja001 Key-on power relay 40-799 40-1331
for fuses F14-15 40-877
40-984
40-1033
40-1151
Ja002 Hi-Lo relay 40-799 40-1331
40-1151
Ja003 Key-on power relay [LNK] 40-1331
for fuses F11-12-13 40-665
40-671
40-750
40-755
[LNK]
40-877
40-922
40-984
40-1033
40-1237
Ja004 Key-on power relay 40-750 40-1331
for fuses F5-6-7-8 40-755
[LNK]
40-984
40-1033
Ja005 Trailer relay 40-799 40-1331
40-877
Ja006 Fan relay [LNK] 40-1331
40-665
40-671
Ja007 Starter relay 40-600 40-1331
40-701
40-1151
Ja008 Fan/compressor re- [LNK] 40-1331
lay (key-on power) 40-665
40-671
Jd001 Key-on power relay 40-816 40-1392
for fuses F14-15 40-889
40-1082
40-1171
Jd002 Hi-Lo relay 40-816 40-1392
40-1171
Jd003 Key-on power relay 40-889 40-1392
for fuses F11-12-13 40-959
Jd004 Key-on power relay [LNK] 40-1392
for fuses F5-6-7-8
Jd005 Trailer relay 40-816 40-1392
40-889
40-1171

40-485
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jd006 Fan relay [LNK] 40-1392
Jd007 Starter relay 40-625 40-1392
40-714
40-1171
Jd008 Fan/compressor re- [LNK] 40-1392
lay (key-on power)
Je001 Max fan speed relay 40-671 40-1301
Je002 Compressor start 40-671 40-1301
relay
Je003 Third fan speed re- 40-671 40-1301
lay

USA version

Jb007 Jb008

Jb001 Jb002 Jb003

Jb004 Jb005 Jb006

Fig. 1107 - Cab fuse box

l Jb001 - Key-on power relay for fuses F14-15
l Jb002 - Hi-Lo relay
l Jb003 - Key-on power relay for fuses F11-12-13
l Jb004 Key-on power relay for fuses F5-6-7-8
l Jb005 - Trailer relay
l Jb006 - Fan relay
l Jb007 - Starter relay
l Jb008 - Fan/compressor relay (key-on power)

40-486
Wiring diagrams

Jh007 Jh008

Jh001 Jh002 Jh003

Jh004 Jh005 Jh006

Fig. 1108 - Platform fuse box

l Jh001 - Key-on power relay for fuses F14-15
l Jh002 - Hi-Lo relay
l Jh003 - Key-on power relay for fuses F11-12-13
l Jh004 - Key-on power relay for fuses F5-6-7-8
l Jh005 - Trailer relay
l Jh006 - Fan relay
l Jh007 - Starter relay
l Jh008 - Fan/compressor relay (key-on power)
Table 307
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-683 40-1308
exchanger fan con- 40-677
trol relay
J002 Auxiliary air condi- 40-683 40-1308
tioner heat exchang- 40-677
er fan control relay
J003 Preheating relay 40-608 40-1324
40-633
40-705
40-719
40-852

40-487
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J004 Preheating relay 40-608 40-1327
40-705
40-719
40-852
40-633
J005 Compressor relay 40-683 40-1275
J006a Preheating relay 40-608 40-1290
40-633
40-705
40-719
J006b Preheating relay 40-608 40-1290
40-633
40-705
40-719
Jb001 Key-on power relay 40-834 40-1347
for fuses F14-15 40-882
40-1001
40-1050
40-1192
Jb002 Hi-Lo relay 40-834 40-1347
40-1192
Jb003 Key-on power relay 40-647 40-1347
for fuses F11-12-13 [LNK]
40-683
40-677
40-764
40-769
[LNK]
40-882
40-935
40-1001
40-1050
40-1240
Jb004 Key-on power relay 40-764 40-1347
for fuses F5-6-7-8 40-769
[LNK]
40-1001
40-1050
Jb005 Trailer relay 40-834 40-1347
40-882
40-1192
Jb006 Fan relay 40-647 40-1347
[LNK]
40-683
40-677
Jb007 Starter relay 40-608 40-1347
40-705
40-1192
Jb008 Fan/compressor re- 40-647 40-1347
lay (key-on power) [LNK]
40-683
40-677
Je001 Max fan speed relay 40-677 40-1301
Je002 Compressor start 40-677 40-1301
relay
Je003 Third fan speed re- 40-677 40-1301
lay
Jh001 Key-on power relay 40-852 40-1410
for fuses F14-15 40-895
40-1093
40-1211

40-488
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jh002 Hi-Lo relay 40-852 40-1410
40-1211
Jh003 Key-on power relay 40-895 40-1410
for fuses F11-12-13 40-970
Jh004 Key-on power relay [LNK] 40-1410
for fuses F5-6-7-8
Jh005 Trailer relay 40-852 40-1410
40-895
40-1211
Jh006 Fan relay [LNK] 40-1410
Jh007 Starter relay 40-633 40-1410
40-719
40-1211
Jh008 Fan/compressor re- [LNK] 40-1410
lay (key-on power)

40.2.55 - J - Relays (AGROFARM 420 -> ZKDW510200TD30001)

ITA version

Ja007 Ja008

Ja001 Ja002 Ja003

Ja004 Ja005 Ja006

Fig. 1109 - Cab fuse box

l Ja001 Key-on power relay for fuses F14-15
l Ja002 - Hi-Lo relay
l Ja003 - Key-on power relay for fuses F11-12-13

40-489
 Wiring diagrams

Ja007 Ja008

Ja001 Ja002 Ja003

Ja004 Ja005 Ja006

Fig. 1109 - Cab fuse box

l Ja004 - Key-on power relay for fuses F5-6-7-8
l Ja005 - Trailer relay
l Ja006 - Fan relay
l Ja007 - Starter relay
l Ja008 - Fan/compressor relay (key-on power)

40-490
Wiring diagrams

Jd007 Jd008

Jd001 Jd002 Jd003

Jd004 Jd005 Jd006

Fig. 1110 - Fuse box, ITA platform version

l Jd001 - Key-on power relay for fuses F14-15
l Jd002 - Hi-Lo relay
l Jd003 - Key-on power relay for fuses F11-12-13
l Jd004 - Key-on power relay for fuses F5-6-7-8
l Jd005 - Trailer relay
l Jd006 - Fan relay
l Jd007 - Starter relay
l Jd008 - Fan/compressor relay (key-on power)
Table 308
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-665 40-1308
exchanger fan con- 40-671
trol relay
J002 Auxiliary air condi- 40-665 40-1308
tioner heat exchang- 40-671
er fan control relay
J003 Preheating relay 40-600 40-1324
40-625
40-701
40-714
40-816

40-491
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J004 Preheating relay 40-600 40-1327
40-701
40-625
40-714
40-816
J005 Compressor relay 40-665 40-1275
J006a Preheating relay 40-600 40-1290
40-625
40-701
40-714
J006b Preheating relay 40-600 40-1290
40-625
40-701
40-714
Ja001 Key-on power relay 40-799 40-1331
for fuses F14-15 40-877
40-984
40-1033
40-1158
Ja002 Hi-Lo relay 40-799 40-1331
40-1158
Ja003 Key-on power relay [LNK] 40-1331
for fuses F11-12-13 40-665
40-671
40-750
40-755
[LNK]
40-877
40-922
40-984
40-1033
40-1237
Ja004 Key-on power relay 40-750 40-1331
for fuses F5-6-7-8 40-755
[LNK]
40-984
40-1033
Ja005 Trailer relay 40-799 40-1331
40-877
Ja006 Fan relay [LNK] 40-1331
40-665
40-671
Ja007 Starter relay 40-600 40-1331
40-701
40-1158
Ja008 Fan/compressor re- [LNK] 40-1331
lay (key-on power) 40-665
40-671
Jd001 Key-on power relay 40-816 40-1392
for fuses F14-15 40-889
40-1082
40-1178
Jd002 Hi-Lo relay 40-816 40-1392
40-1178
Jd003 Key-on power relay 40-889 40-1392
for fuses F11-12-13 40-959
Jd004 Key-on power relay [LNK] 40-1392
for fuses F5-6-7-8
Jd005 Trailer relay 40-816 40-1392
40-889
40-1178

40-492
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jd006 Fan relay [LNK] 40-1392
Jd007 Starter relay 40-625 40-1392
40-714
40-1178
Jd008 Fan/compressor re- [LNK] 40-1392
lay (key-on power)
Je001 Max fan speed relay 40-671 40-1301
Je002 Compressor start 40-671 40-1301
relay
Je003 Third fan speed re- 40-671 40-1301
lay

USA version

Jb007 Jb008

Jb001 Jb002 Jb003

Jb004 Jb005 Jb006

Fig. 1111 - Cab fuse box

l Jb001 - Key-on power relay for fuses F14-15
l Jb002 - Hi-Lo relay
l Jb003 - Key-on power relay for fuses F11-12-13
l Jb004 Key-on power relay for fuses F5-6-7-8
l Jb005 - Trailer relay
l Jb006 - Fan relay
l Jb007 - Starter relay
l Jb008 - Fan/compressor relay (key-on power)

40-493
 Wiring diagrams

Jh007 Jh008

Jh001 Jh002 Jh003

Jh004 Jh005 Jh006

Fig. 1112 - Platform fuse box

l Jh001 - Key-on power relay for fuses F14-15
l Jh002 - Hi-Lo relay
l Jh003 - Key-on power relay for fuses F11-12-13
l Jh004 - Key-on power relay for fuses F5-6-7-8
l Jh005 - Trailer relay
l Jh006 - Fan relay
l Jh007 - Starter relay
l Jh008 - Fan/compressor relay (key-on power)
Table 309
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-683 40-1308
exchanger fan con- 40-677
trol relay
J002 Auxiliary air condi- 40-683 40-1308
tioner heat exchang- 40-677
er fan control relay
J003 Preheating relay 40-608 40-1324
40-633
40-705
40-719
40-852

40-494
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J004 Preheating relay 40-608 40-1327
40-705
40-719
40-852
40-633
J005 Compressor relay 40-683 40-1275
J006a Preheating relay 40-608 40-1290
40-633
40-705
40-719
J006b Preheating relay 40-608 40-1290
40-633
40-705
40-719
Jb001 Key-on power relay 40-834 40-1347
for fuses F14-15 40-882
40-1001
40-1050
40-1199
Jb002 Hi-Lo relay 40-834 40-1347
40-1199
Jb003 Key-on power relay 40-647 40-1347
for fuses F11-12-13 [LNK]
40-683
40-677
40-764
40-769
[LNK]
40-882
40-935
40-1001
40-1050
40-1240
Jb004 Key-on power relay 40-764 40-1347
for fuses F5-6-7-8 40-769
[LNK]
40-1001
40-1050
Jb005 Trailer relay 40-834 40-1347
40-882
40-1199
Jb006 Fan relay 40-647 40-1347
[LNK]
40-683
40-677
Jb007 Starter relay 40-608 40-1347
40-705
40-1199
Jb008 Fan/compressor re- 40-647 40-1347
lay (key-on power) [LNK]
40-683
40-677
Je001 Max fan speed relay 40-677 40-1301
Je002 Compressor start 40-677 40-1301
relay
Je003 Third fan speed re- 40-677 40-1301
lay
Jh001 Key-on power relay 40-852 40-1410
for fuses F14-15 40-895
40-1093
40-1218

40-495
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jh002 Hi-Lo relay 40-852 40-1410
40-1218
Jh003 Key-on power relay 40-895 40-1410
for fuses F11-12-13 40-970
Jh004 Key-on power relay [LNK] 40-1410
for fuses F5-6-7-8
Jh005 Trailer relay 40-852 40-1410
40-895
40-1218
Jh006 Fan relay [LNK] 40-1410
Jh007 Starter relay 40-633 40-1410
40-719
40-1218
Jh008 Fan/compressor re- [LNK] 40-1410
lay (key-on power)

40.2.56 - J - Relays (AGROFARM 430 -> ZKDW550200TD30001)

ITA version

Ja007 Ja008

Ja001 Ja002 Ja003

Ja004 Ja005 Ja006

Fig. 1113 - Cab fuse box

l Ja001 - Key-on power relay for fuses F14-15
l Ja002 - Hi-Lo relay
l Ja003 - Key-on power relay for fuses F11-12-13

40-496
Wiring diagrams

Ja007 Ja008

Ja001 Ja002 Ja003

Ja004 Ja005 Ja006

Fig. 1113 - Cab fuse box

l Ja004 - Key-on power relay for fuses F5-6-7-8
l Ja005 - Trailer relay
l Ja006 - Fan relay
l Ja007 - Starter relay
l Ja008 - Fan/compressor relay (key-on power)

40-497
 Wiring diagrams

Jc007 Jc008

Jc001 Jc002 Jc003

Jc004 Jc005 Jc006

Fig. 1114 - Cab fuse box, version with electronic lift

l Jc001 - Key-on power relay for fuses F14-15
l Jc002 - Hi-Lo relay
l Jc003 - Key-on power relay for fuses F11-12-13
l Jc004 - Key-on power relay for fuses F5-6-7-8
l Jc006 - Fan relay
l Jc007 - Starter relay
l Ja008 - Fan/compressor relay (key-on power)
Table 310
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-665 40-1308
exchanger fan con- 40-671
trol relay 40-689
40-695
J002 Auxiliary air condi- 40-665 40-1308
tioner heat exchang- 40-671
er fan control relay 40-689
40-695
J003 Preheating relay 40-600 40-1324
40-701
40-714
40-616
40-710

40-498
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J004 Preheating relay 40-600 40-1327
40-701
40-714
40-616
40-710
J005 Compressor relay 40-665 40-1275
40-689
J006a Preheating relay 40-600 40-1290
40-701
40-714
40-616
40-710
J006b Preheating relay 40-600 40-1290
40-701
40-714
40-616
40-710
Ja001 Key-on power relay 40-799 40-1331
for fuses F14-15 40-877
40-984
40-1033
40-1158
Ja002 Hi-Lo relay 40-799 40-1331
40-1158
Ja003 Key-on power relay 40-665 40-1331
for fuses F11-12-13 40-671
40-750
40-755
40-877
40-922
40-984
40-1033
40-1237
Ja004 Key-on power relay 40-750 40-1331
for fuses F5-6-7-8 40-755
40-984
40-1033
Ja005 Trailer relay 40-799 40-1331
40-877
Ja006 Fan relay 40-665 40-1331
40-671
Ja007 Starter relay 40-600 40-1331
40-701
40-1158
Ja008 Fan/compressor re- 40-665 40-1331
lay (key-on power) 40-671
Jc001 Key-on power relay 40-870 40-1365
for fuses F14-15 40-902
40-1016
40-1067
Jc002 Hi-Lo relay 40-870 40-1365
40-1231
Jc003 Key-on power relay 40-689 40-1365
for fuses F11-12-13 40-778
40-783
40-948
40-1016
40-1067
40-695

40-499
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jc004 Key-on power relay 40-778 40-1365
for fuses F5-6-7-8 40-783
40-1016
40-1067
Jc005 Trailer relay 40-870 40-1365
40-902
Jc006 Fan relay 40-689 40-1365
40-695
Jc007 Starter relay 40-616 40-1365
40-710
40-1231
Jc008 Fan/compressor re- 40-689 40-1365
lay (key-on power) 40-695
Je001 Max fan speed relay 40-671 40-1301
40-695
Je002 Compressor start 40-671 40-1301
relay 40-695
Je003 Third fan speed re- 40-671 40-1301
lay 40-695

USA version

Jb007 Jb008

Jb001 Jb002 Jb003

Jb004 Jb005 Jb006

Fig. 1115 - Cab fuse box

l Jb001 - Key-on power relay for fuses F14-15

40-500
Wiring diagrams

Jb007 Jb008

Jb001 Jb002 Jb003

Jb004 Jb005 Jb006

Fig. 1115 - Cab fuse box

l Jb002 - Hi-Lo relay
l Jb003 - Key-on power relay for fuses F11-12-13
l Jb004 - Key-on power relay for fuses F5-6-7-8
l Jb005 - Trailer relay
l Jb006 - Fan relay
l Jb007 - Starter relay
l Jb008 - Fan/compressor relay (key-on power)

40-501
 Wiring diagrams

Jc007 Jc008

Jc001 Jc002 Jc003

Jc004 Jc005 Jc006

Fig. 1115 - Cab fuse box, version with electronic lift

l Jc001 - Key-on power relay for fuses F14-15
l Jc002 - Hi-Lo relay
l Jc003 - Key-on power relay for fuses F11-12-13
l Jc004 - Key-on power relay for fuses F5-6-7-8
l Jc006 - Fan relay
l Jc007 - Starter relay
l Ja008 - Fan/compressor relay (key-on power)
Table 311
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J001 Air conditioner heat 40-683 40-1308
exchanger fan con- 40-677
trol relay 40-689
40-695
J002 Auxiliary air condi- 40-683 40-1308
tioner heat exchang- 40-677
er fan control relay 40-689
40-695
J003 Preheating relay 40-608 40-1324
40-705
40-719
40-616
40-710

40-502
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
J004 Preheating relay 40-608 40-1327
40-705
40-719
40-616
40-710
J005 Compressor relay 40-683 40-1275
40-689
J006a Preheating relay 40-608 40-1290
40-705
40-719
40-616
40-710
J006b Preheating relay 40-608 40-1290
40-705
40-719
40-616
40-710
Jb001 Key-on power relay 40-834 40-1347
for fuses F14-15 40-882
40-1001
40-1050
40-1199
Jb002 Hi-Lo relay 40-834 40-1347
40-1199
Jb003 Key-on power relay 40-647 40-1347
for fuses F11-12-13 40-683
40-677
40-764
40-769
40-882
40-935
40-1001
40-1050
40-1240
Jb004 Key-on power relay 40-764 40-1347
for fuses F5-6-7-8 40-769
40-1001
40-1050
Jb005 Trailer relay 40-834 40-1347
40-882
40-1199
Jb006 Fan relay 40-647 40-1347
40-683
40-677
Jb007 Starter relay 40-608 40-1347
40-705
40-1199
Jb008 Fan/compressor re- 40-647 40-1347
lay (key-on power) 40-683
40-677
Jc001 Key-on power relay 40-870 40-1365
for fuses F14-15 40-902
40-1016
40-1067
Jc002 Hi-Lo relay 40-870 40-1365
40-1231
Jc003 Key-on power relay 40-689 40-1365
for fuses F11-12-13 40-778
40-783
40-948
40-1016
40-1067

40-503
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Jc004 Key-on power relay 40-778 40-1365
for fuses F5-6-7-8 40-783
40-1016
40-1067
Jc005 Trailer relay 40-870 40-1365
40-902
Jc006 Fan relay 40-689 40-1365
40-695
Jc007 Starter relay 40-616 40-1365
40-710
40-1231
Jc008 Fan/compressor re- 40-689 40-1365
lay (key-on power) 40-695
Je001 Max fan speed relay 40-677 40-1301
40-695
Je002 Compressor start 40-677 40-1301
relay 40-695
Je003 Third fan speed re- 40-677 40-1301
lay 40-695

40.2.57 - K - Sensors and transmitters (AGROFARM 410 -> ZKDW350200TD25001)

ITA version
Table 312
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K001 0.011.9428.0 Trailer braking low 40-877 40-1287
pressure switch 40-889

K009 Stoll 40-807 40-1306

K010 Transmission filter 40-791 40-1306
clogging sensor 40-807
40-1145
40-1166
K011 2.7659.096.0/10 Dual traction sensor 40-791 40-1306
CB A

Between Pin 1 and 40-807

Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-1145
Pin 3: Normally open 40-1166
(NO) contact
K012 Transmission oil 40-791 40-1306
filter clogging pres- 40-807
sure switch 40-1145
40-1166
K013 Wheels speed sen- 40-791 40-1306
sor 40-807
40-1145
40-1166
K014 Services circuit 40-791 40-1306
alarm pressure 40-807
switch

40-504
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K015 Hydraulic trailer 40-791 40-1306
braking valve pres- 40-807
sure switch 40-877
40-889
K016 Fuel level sensor 40-791 40-1306
40-807
K017 Air conditioning 40-665 40-1308
pressure switch 40-671
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-791 40-1324
sensor tact
Switching pressure: 40-807
0.93 to 0.94 bar ab-
solute pressure
K019 Brake fluid level sen- 40-791 40-1324
sor 40-807
K020 Engine oil pressure 40-701 40-1324
switch 40-714
40-791
40-807
K021 Engine temperature 40-701 40-1324
sensor 40-714
40-807
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-791 40-1327
sensor tact
Switching pressure: 40-807
0.93 to 0.94 bar ab-
solute pressure
K024 Brake fluid level sen- 40-791 40-1327
sor 40-807
K025 Engine oil pressure 40-701 40-1327
switch 40-714
40-791
40-807
K026 Engine temperature 40-701 40-1327
sensor 40-714
40-807
K028 Antifrost thermostat [LNK] 40-1318

40-505
 Wiring diagrams
Table 313
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K037 2.7659.097.0 Handbrake pressure 1 40-791 40-1331
switch
4

Between Pin 1 and 40-877

Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1145
Pin 4: normally open
(NO) switch
K052 2.7659.097.0 Handbrake pressure 1 40-807 40-1392
switch
4

Between Pin 1 and 40-889

Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1166
Pin 4: normally open
(NO) switch
K053 Operator present 40-807 40-1392
sensor in seat
K055 Operator present 40-791 40-1331
sensor in seat
K056 MTA connector 40-671 40-1301
USA version
Table 314
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K008 PTO speed sensor 40-728 40-1300
40-743
K009 Stoll 40-843 40-1306
K010 Transmission filter 40-826 40-1306
clogging sensor 40-843
40-1186
40-1206
K011 2.7659.096.0/10 Dual traction sensor 40-826 40-1306
CB A

Between Pin 1 and 40-843

Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-1186
Pin 3: Normally open 40-1206
(NO) contact
K012 Transmission oil 40-826 40-1306
filter clogging pres- 40-843
sure switch 40-1186
40-1206
K013 Wheels speed sen- 40-826 40-1306
sor 40-843
40-1186
40-1206
K014 Services circuit 40-826 40-1306
alarm pressure 40-843
switch

40-506
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K015 Hydraulic trailer 40-826 40-1306
braking valve pres- 40-843
sure switch 40-882
40-895
K016 Fuel level sensor 40-826 40-1306
40-843
K017 Air conditioning 40-683 40-1308
pressure switch 40-677
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-826 40-1324
sensor tact
Switching pressure: 40-843
0.93 to 0.94 bar ab-
solute pressure
K019 Brake fluid level sen- 40-826 40-1324
sor 40-843
K020 Engine oil pressure 40-705 40-1324
switch 40-719
40-826
40-843
K021 Engine temperature 40-705 40-1324
sensor 40-719
40-843
K022 Operator present [LNK] 40-1410
sensor in seat
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-826 40-1327
sensor tact
Switching pressure: 40-843
0.93 to 0.94 bar ab-
solute pressure
K024 Brake fluid level sen- 40-826 40-1327
sor 40-843
K025 Engine oil pressure 40-705 40-1327
switch 40-719
40-826
40-843
K026 Engine temperature 40-705 40-1327
sensor 40-719
40-843
K027 2.7659.097.0 Handbrake pressure 1 40-843 40-1410
switch
4

Between Pin 1 and 40-895

Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1206
Pin 4: normally open
(NO) switch
K028 Antifrost thermostat [LNK] 40-1318

40-507
 Wiring diagrams
Table 315
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K038 2.7659.097.0 Handbrake pressure 1 40-826 40-1347
switch
4

Between Pin 1 and 40-882

Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1186
Pin 4: normally open
(NO) switch
K039 Operator present 40-826 40-1347
sensor in seat
K056 MTA connector 40-677 40-1301

40.2.58 - K - Sensors and transmitters (AGROFARM 420 -> ZKDW390200TD25001)

ITA version
Table 316
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K001 0.011.9428.0 Trailer braking low 40-877 40-1287
pressure switch 40-889

K009 Stoll 40-807 40-1306

K010 Transmission filter 40-791 40-1306
clogging sensor 40-807
40-1145
40-1166
K011 2.7659.096.0/10 Dual traction sensor 1 40-791 40-1306

Between Pin 1 and 40-807

Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-1145
Pin 3: Normally open 40-1166
(NO) contact
K012 Transmission oil 40-791 40-1306
filter clogging pres- 40-807
sure switch 40-1145
40-1166
K013 Wheels speed sen- 40-791 40-1306
sor 40-807
40-1145
40-1166
K014 Services circuit 40-791 40-1306
alarm pressure 40-807
switch

40-508
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K015 Hydraulic trailer 40-791 40-1306
braking valve pres- 40-807
sure switch 40-877
40-889
K016 Fuel level sensor 40-791 40-1306
40-807
K017 Air conditioning 40-665 40-1308
pressure switch 40-671
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-791 40-1324
sensor tact
Switching pressure: 40-807
0.93 to 0.94 bar ab-
solute pressure
K019 Brake fluid level sen- 40-791 40-1324
sor 40-807
K020 Engine oil pressure 40-701 40-1324
switch 40-714
40-791
40-807
K021 Engine temperature 40-701 40-1324
sensor 40-714
40-807
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-791 40-1327
sensor tact
Switching pressure: 40-807
0.93 to 0.94 bar ab-
solute pressure
K024 Brake fluid level sen- 40-791 40-1327
sor 40-807
K025 Engine oil pressure 40-701 40-1327
switch 40-714
40-791
40-807
K026 Engine temperature 40-701 40-1327
sensor 40-714
40-807
K028 Antifrost thermostat [LNK] 40-1318
K030 Engine coolant tem- 40-701 40-1425
perature sensor 40-714
K031 Not used [LNK] 40-1425
K032 Turbine air tempera- 40-701 40-1425
ture/pressure sensor 40-714
K033 Not used [LNK] 40-1425
K034 Not used [LNK] 40-1425
K035 Camshaft speed 40-701 40-1425
sensor 40-714
K036 Fuel temperature 40-701 40-1425
sensor 40-714

40-509
 Wiring diagrams
Table 317
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K037 2.7659.097.0 Handbrake pressure 40-791 40-1331

P=
XX
X
XX
switch

XX

X
X
Between Pin 1 and 40-877
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1145
Pin 4: normally open
(NO) switch
K052 2.7659.097.0 Handbrake pressure 40-807 40-1392

P=
XX
X
XX
switch
XX

X
X

Between Pin 1 and 40-889

Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1166
Pin 4: normally open
(NO) switch
K053 Operator present 40-807 40-1392
sensor in seat
K055 Operator present 40-791 40-1331
sensor in seat
K056 MTA connector 40-671 40-1301
USA version
Table 318
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K008 PTO speed sensor 40-728 40-1300
40-743
K009 Stoll 40-843 40-1306
K010 Transmission filter 40-826 40-1306
clogging sensor 40-843
40-1186
40-1206
K011 2.7659.096.0/10 Dual traction sensor 1 40-826 40-1306

Between Pin 1 and 40-843

Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-1186
Pin 3: Normally open 40-1206
(NO) contact

40-510
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K012 Transmission oil 40-826 40-1306
filter clogging pres- 40-843
sure switch 40-1186
40-1206
K013 Wheels speed sen- 40-826 40-1306
sor 40-843
40-1186
40-1206
K014 Services circuit 40-826 40-1306
alarm pressure 40-843
switch
K015 Hydraulic trailer 40-826 40-1306
braking valve pres- 40-843
sure switch 40-882
40-895
K016 Fuel level sensor 40-826 40-1306
40-843
K017 Air conditioning 40-683 40-1308
pressure switch 40-677
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-826 40-1324
sensor tact
Switching pressure: 40-843
0.93 to 0.94 bar ab-
solute pressure
K019 Brake fluid level sen- 40-826 40-1324
sor 40-843
K020 Engine oil pressure 40-705 40-1324
switch 40-719
40-826
40-843
K021 Engine temperature 40-705 40-1324
sensor 40-719
40-843
K022 Operator present [LNK] 40-1410
sensor in seat
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-826 40-1327
sensor tact
Switching pressure: 40-843
0.93 to 0.94 bar ab-
solute pressure
K024 Brake fluid level sen- 40-826 40-1327
sor 40-843
K025 Engine oil pressure 40-705 40-1327
switch 40-719
40-826
40-843
K026 Engine temperature 40-705 40-1327
sensor 40-719
40-843

40-511
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K027 2.7659.097.0 Handbrake pressure 40-843 40-1410

P=
XX
X
XX
switch

XX

X
X
Between Pin 1 and 40-895
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1206
Pin 4: normally open
(NO) switch
K028 Antifrost thermostat [LNK] 40-1318
K030 Engine coolant tem- 40-705 40-1425
perature sensor 40-719
K031 Not used [LNK] 40-1425
K032 Turbine air tempera- 40-705 40-1425
ture/pressure sensor 40-719
K033 Not used [LNK] 40-1425
K034 Not used [LNK] 40-1425
K035 Camshaft speed 40-705 40-1425
sensor 40-719
K036 Fuel temperature 40-705 40-1425
sensor 40-719

Table 319
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K038 2.7659.097.0 Handbrake pressure 40-826 40-1347
P=
XX
X
XX

switch
XX

X
X

Between Pin 1 and 40-882

Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1186
Pin 4: normally open
(NO) switch
K039 Operator present 40-826 40-1347
sensor in seat
K056 MTA connector 40-677 40-1301

40.2.59 - K - Sensors and transmitters (AGROFARM 430 -> ZKDW430200TD25001)

40-512
Wiring diagrams
ITA version
Table 320
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K001 0.011.9428.0 Trailer braking low 40-877 40-1287
pressure switch 40-889

K009 Stoll 40-807 40-1306

K010 Transmission filter 40-791 40-1306
clogging sensor 40-807
K011 2.7659.096.0/10 Dual traction sensor 40-791 40-1306

P=
XX
X
XX
XX

X
X

Between Pin 1 and 40-807

Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-1145
Pin 3: Normally open 40-1166
(NO) contact
K012 Transmission oil 40-791 40-1306
filter clogging pres- 40-807
sure switch 40-1145
40-1166
K013 Wheels speed sen- 40-791 40-1306
sor 40-807
40-1145
40-1166
K014 Services circuit 40-791 40-1306
alarm pressure 40-807
switch
K015 Hydraulic trailer 40-791 40-1306
braking valve pres- 40-807
sure switch 40-877
40-889
K016 Fuel level sensor 40-791 40-1306
40-807
K017 Air conditioning 40-665 40-1308
pressure switch 40-671
40-689
40-695
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-791 40-1324
sensor tact
Switching pressure: 40-862
0.93 to 0.94 bar ab- 40-807
solute pressure
K019 Brake fluid level sen- 40-791 40-1324
sor 40-862
40-807

40-513
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K020 Engine oil pressure 40-701 40-1324
switch 40-710
40-714
40-862
40-791
40-807
K021 Engine temperature 40-701 40-1324
sensor 40-710
40-807
40-714
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-791 40-1327
sensor tact 40-862
Switching pressure: 40-807
0.93 to 0.94 bar ab-
solute pressure
K024 Brake fluid level sen- 40-791 40-1327
sor 40-862
40-807
K025 Engine oil pressure 40-701 40-1327
switch 40-710
40-714
40-791
40-807
40-862
K026 Engine temperature 40-701 40-1327
sensor 40-710
40-807
40-714
K028 Antifrost thermostat [LNK] 40-1318
K030 Engine coolant tem- 40-701 40-1425
perature sensor 40-714
40-710
K031 Not used [LNK] 40-1425
K032 Turbine air tempera- 40-701 40-1425
ture/pressure sensor 40-714
40-710
K033 Not used [LNK] 40-1425
K034 Not used [LNK] 40-1425
K035 Camshaft speed 40-701 40-1425
sensor 40-714
40-710
K036 Fuel temperature 40-701 40-1425
sensor 40-714
40-710

40-514
Wiring diagrams
Table 321
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K037 2.7659.097.0 Handbrake pressure 40-791 40-1331

CB A
switch
Between Pin 1 and 40-877
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1145
Pin 4: normally open
(NO) switch
K040 2.7659.097.0 Handbrake pressure 1 40-862 40-1365
switch
4

Between Pin 1 and 40-902

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
K041 Operator present 40-862 40-1365
sensor in seat
K042 Lift position sensor 40-1269 40-1382
K043 Lift draft sensor 40-1269 40-1382
K044 Services circuit 40-862 40-1385
alarm pressure
switch
K045 Wheels speed sen- 40-862 40-1385
sor 40-1226
K046 2.7099.960.0 Hydraulic trailer 40-862 40-1385
P=
XX
X
XX

braking valve pres-

XX

X
X

sure switch

Normally closed 40-902

(NC) contact
Switching pressure:
11 bar
K047 2.7659.096.0/10 Dual traction sensor 40-862 40-1385
CB A

Between Pin 1 and 40-1226

Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
K048 Fuel level sensor 40-862 40-1385
K049 Transmission oil 40-862 40-1385
filter clogging pres- 40-1226
sure switch
K050 Transmission filter 40-862 40-1385
clogging sensor 40-1226
K051 Stoll [LNK] 40-1385

40-515
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K052 2.7659.097.0 Handbrake pressure 40-807 40-1392

CB A
switch
Between Pin 1 and 40-889
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1166
Pin 4: normally open
(NO) switch
K053 Operator present 40-807 40-1392
sensor in seat
K055 Operator present 40-791 40-1331
sensor in seat
K056 MTA connector 40-671 40-1301

USA version
Table 322
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K001 0.011.9428.0 Trailer braking low 40-882 40-1287
pressure switch 40-895

K008 PTO speed sensor 40-728 40-1300

40-734
40-743
K009 Stoll 40-843 40-1306
K010 Transmission filter 40-826 40-1306
clogging sensor 40-843
K011 2.7659.096.0/10 Dual traction sensor 40-826 40-1306
P=
XX
X
XX
XX

X
X

Between Pin 1 and 40-843

Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-1186
Pin 3: Normally open 40-1206
(NO) contact
K012 Transmission oil 40-826 40-1306
filter clogging pres- 40-843
sure switch 40-1186
40-1206
K013 Wheels speed sen- 40-826 40-1306
sor 40-843
40-1186
40-1206

40-516
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K014 Services circuit 40-826 40-1306
alarm pressure 40-843
switch
K015 Hydraulic trailer 40-826 40-1306
braking valve pres- 40-843
sure switch 40-882
40-895
K016 Fuel level sensor 40-826 40-1306
40-843
K017 Air conditioning 40-683 40-1308
pressure switch 40-689
40-695
40-677
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-826 40-1324
sensor tact 40-862
Switching pressure: 40-843
0.93 to 0.94 bar ab-
solute pressure
K019 Brake fluid level sen- 40-826 40-1324
sor 40-862
40-843
K020 Engine oil pressure 40-705 40-1324
switch 40-710
40-719
40-826
40-843
40-862
K021 Engine temperature 40-705 40-1324
sensor 40-710
40-843
40-719
K022 Operator present 40-843 40-1410
sensor in seat
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-826 40-1327
sensor tact 40-862
Switching pressure: 40-843
0.93 to 0.94 bar ab-
solute pressure
K024 Brake fluid level sen- 40-826 40-1327
sor 40-862
40-843
K025 Engine oil pressure 40-705 40-1327
switch 40-710
40-719
40-826
40-843
40-862
K026 Engine temperature 40-705 40-1327
sensor 40-710
40-843
40-719
K027 2.7659.097.0 Handbrake pressure 40-843 40-1410
CB A

switch
Between Pin 1 and 40-895
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1206
Pin 4: normally open
(NO) switch
K028 Antifrost thermostat [LNK] 40-1318

40-517
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K030 Engine coolant tem- 40-705 40-1425
perature sensor 40-719
40-710
K031 Not used [LNK] 40-1425
K032 Turbine air tempera- 40-705 40-1425
ture/pressure sensor 40-719
40-710
K033 Not used [LNK] 40-1425
K034 Not used [LNK] 40-1425
K035 Camshaft speed 40-705 40-1425
sensor 40-719
40-710
K036 Fuel temperature 40-705 40-1425
sensor 40-719
40-710
Table 323
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K038 2.7659.097.0 Handbrake pressure 40-826 40-1347

CB A
switch
Between Pin 1 and 40-882
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1186
Pin 4: normally open
(NO) switch
K039 Operator present 40-826 40-1347
sensor in seat
K040 2.7659.097.0 Handbrake pressure 1 40-862 40-1365
switch
4

Between Pin 1 and 40-902

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
K041 Operator present 40-862 40-1365
sensor in seat
K042 Lift position sensor 40-1269 40-1382
K043 Lift draft sensor 40-1269 40-1382
K044 Services circuit 40-862 40-1385
alarm pressure
switch
K045 Wheels speed sen- 40-862 40-1385
sor 40-1226

40-518
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K046 2.7099.960.0 Hydraulic trailer 40-862 40-1385

P=
XX
X
XX
braking valve pres-

XX

X
X
sure switch

Normally closed 40-902

(NC) contact
Switching pressure:
11 bar
K047 2.7659.096.0/10 Dual traction sensor 40-862 40-1385

CB A
Between Pin 1 and 40-1226
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
K048 Fuel level sensor 40-862 40-1385
K049 Transmission oil 40-862 40-1385
filter clogging pres- 40-1226
sure switch
K050 Transmission filter 40-862 40-1385
clogging sensor 40-1226
K051 Stoll [LNK] 40-1385
K056 MTA connector 40-677 40-1301

40.2.60 - K - Sensors and transmitters (AGROFARM 410 -> ZKDW470200TD30001)

ITA version
Table 324
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K001 0.011.9428.0 Trailer braking low 40-877 40-1287
pressure switch 40-889

K002 Clutch pedal position 40-1151 40-1293

sensor 40-1151
40-1171
K003 2.7099.996.0 Engine speed sen- This cannot be [LNK] 40-1296
sor checked using an
ordinary tester; use
the ART.
K004 2.7099.740.0/10 Shuttle sensor Pin 1 = power (Nomi- [LNK] 40-1296
nal 5.0V)
Pin 2 = ground
Pin 4 = analogue
signal

40-519
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K005 2.7099.800.0 Oil temperature sen- [LNK] 40-1296
sor
K006 2.7099.690.0/10 Clutch oil pressure Normally closed [LNK] 40-1296
switch (NC) contact
Switching pressure:
4 Bar
K007 PALL filter clogging [LNK] 40-1296
sensor
K009 Stoll 40-816 40-1306
K010 Transmission filter 40-799 40-1306
clogging sensor 40-816
40-1151
40-1171
K011 2.7659.096.0/10 Dual traction sensor 40-799 40-1306

CB A
Between Pin 1 and 40-816
Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-1151
Pin 3: Normally open 40-1171
(NO) contact
K012 Transmission oil 40-799 40-1306
filter clogging pres- 40-816
sure switch 40-1151
40-1171
K013 Wheels speed sen- 40-799 40-1306
sor 40-816
40-1151
40-1171
K014 Services circuit 40-799 40-1306
alarm pressure 40-816
switch
K015 Hydraulic trailer 40-799 40-1306
braking valve pres- 40-816
sure switch 40-877
40-889
K016 Fuel level sensor 40-799 40-1306
40-816
K017 Air conditioning 40-665 40-1308
pressure switch 40-671
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-799 40-1324
sensor tact
Switching pressure: 40-816
0.93 to 0.94 bar ab-
solute pressure
K019 Brake fluid level sen- 40-799 40-1324
sor 40-816
K020 Engine oil pressure 40-701 40-1324
switch 40-714
40-799
40-816
K021 Engine temperature 40-701 40-1324
sensor 40-714
40-816
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-799 40-1327
sensor tact
Switching pressure: 40-816
0.93 to 0.94 bar ab-
solute pressure

40-520
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K024 Brake fluid level sen- 40-799 40-1327
sor 40-816
K025 Engine oil pressure 40-701 40-1327
switch 40-714
40-799
40-816
K026 Engine temperature 40-701 40-1327
sensor 40-714
40-816
K030 Engine coolant tem- 40-701 40-1425
perature sensor 40-714
K031 Not used [LNK] 40-1425
K032 Turbine air tempera- 40-701 40-1425
ture/pressure sensor 40-714
K033 Not used [LNK] 40-1425
K034 Not used [LNK] 40-1425
K035 Camshaft speed 40-701 40-1425
sensor 40-714
K036 Fuel temperature 40-701 40-1425
sensor 40-714

Table 325
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K037 2.7659.097.0 Handbrake pressure 1 40-799 40-1331
switch
4

Between Pin 1 and 40-877

Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1151
Pin 4: normally open
(NO) switch
K052 2.7659.097.0 Handbrake pressure 1 40-816 40-1392
switch
4

Between Pin 1 and 40-889

Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1171
Pin 4: normally open
(NO) switch
K053 Operator present 40-816 40-1392
sensor in seat
K054 Pall filter [LNK] 40-1293
K055 Operator present 40-799 40-1331
sensor in seat
K056 MTA connector 40-671 40-1301
USA version
Table 326
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K002 Clutch pedal position 40-1192 40-1293
sensor 40-1211

40-521
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K003 2.7099.996.0 Engine speed sen- This cannot be [LNK] 40-1296
sor checked using an
ordinary tester; use
the ART.
K004 2.7099.740.0/10 Shuttle sensor Pin 1 = power (Nomi- [LNK] 40-1296
nal 5.0V)
Pin 2 = ground
Pin 4 = analogue
signal
K005 2.7099.800.0 Oil temperature sen- [LNK] 40-1296
sor
K006 2.7099.690.0/10 Clutch oil pressure Normally closed [LNK] 40-1296
switch (NC) contact
Switching pressure:
4 Bar
K007 PALL filter clogging [LNK] 40-1296
sensor
K008 PTO speed sensor 40-728 40-1300
40-743
K009 Stoll 40-852 40-1306
K010 Transmission filter 40-834 40-1306
clogging sensor 40-852
40-1192
40-1211
K011 2.7659.096.0/10 Dual traction sensor 40-834 40-1306
CB A

Between Pin 1 and 40-852

Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-1192
Pin 3: Normally open 40-1211
(NO) contact
K012 Transmission oil 40-834 40-1306
filter clogging pres- 40-852
sure switch 40-1192
40-1211
K013 Wheels speed sen- 40-834 40-1306
sor 40-852
40-1192
40-1211
K014 Services circuit 40-834 40-1306
alarm pressure 40-852
switch
K015 Hydraulic trailer 40-834 40-1306
braking valve pres- 40-852
sure switch 40-882
40-895
K016 Fuel level sensor 40-834 40-1306
40-852
K017 Air conditioning 40-683 40-1308
pressure switch 40-677
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-834 40-1324
sensor tact
Switching pressure: 40-852
0.93 to 0.94 bar ab-
solute pressure
K019 Brake fluid level sen- 40-834 40-1324
sor 40-852

40-522
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K020 Engine oil pressure 40-705 40-1324
switch 40-719
40-834
40-852
K021 Engine temperature 40-705 40-1324
sensor 40-719
40-852
K022 Operator present [LNK] 40-1410
sensor in seat
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-834 40-1327
sensor tact
Switching pressure: 40-852
0.93 to 0.94 bar ab-
solute pressure
K024 Brake fluid level sen- 40-834 40-1327
sor 40-852
K025 Engine oil pressure 40-705 40-1327
switch 40-719
40-834
40-852
K026 Engine temperature 40-705 40-1327
sensor 40-719
40-852
K027 2.7659.097.0 Handbrake pressure 1 40-852 40-1410
switch
4

Between Pin 1 and 40-895

Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1211
Pin 4: normally open
(NO) switch
K030 Engine coolant tem- 40-705 40-1425
perature sensor 40-719
K031 Not used [LNK] 40-1425
K032 Turbine air tempera- 40-705 40-1425
ture/pressure sensor 40-719
K033 Not used [LNK] 40-1425
K034 Not used [LNK] 40-1425
K035 Camshaft speed 40-705 40-1425
sensor 40-719
K036 Fuel temperature 40-705 40-1425
sensor 40-719

40-523
 Wiring diagrams
Table 327
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K038 2.7659.097.0 Handbrake pressure 1 40-834 40-1347
switch
4

Between Pin 1 and 40-882

Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1192
Pin 4: normally open
(NO) switch
K039 Operator present 40-834 40-1347
sensor in seat
K054 Pall filter [LNK] 40-1293
K056 MTA connector 40-677 40-1301

40.2.61 - K - Sensors and transmitters (AGROFARM 420 -> ZKDW510200TD30001)

ITA version
Table 328
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K001 0.011.9428.0 Trailer braking low 40-877 40-1287
pressure switch 40-889

K002 Clutch pedal position 40-1158 40-1293

sensor 40-1158
40-1178
K003 2.7099.996.0 Engine speed sen- This cannot be [LNK] 40-1296
sor checked using an
ordinary tester; use
the ART.
K004 2.7099.740.0/10 Shuttle sensor Pin 1 = power (Nomi- [LNK] 40-1296
nal 5.0V)
Pin 2 = ground
Pin 4 = analogue
signal
K005 2.7099.800.0 Oil temperature sen- [LNK] 40-1296
sor
K006 2.7099.690.0/10 Clutch oil pressure Normally closed [LNK] 40-1296
switch (NC) contact
Switching pressure:
4 Bar
K007 PALL filter clogging [LNK] 40-1296
sensor
K009 Stoll 40-816 40-1306
K010 Transmission filter 40-799 40-1306
clogging sensor 40-816
40-1158
40-1178

40-524
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K011 2.7659.096.0/10 Dual traction sensor 40-799 40-1306

P=
XX
X
XX
XX

X
X
Between Pin 1 and 40-816
Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-1158
Pin 3: Normally open 40-1178
(NO) contact
K012 Transmission oil 40-799 40-1306
filter clogging pres- 40-816
sure switch 40-1158
40-1178
K013 Wheels speed sen- 40-799 40-1306
sor 40-816
40-1158
40-1178
K014 Services circuit 40-799 40-1306
alarm pressure 40-816
switch
K015 Hydraulic trailer 40-799 40-1306
braking valve pres- 40-816
sure switch 40-877
40-889
K016 Fuel level sensor 40-799 40-1306
40-816
K017 Air conditioning 40-665 40-1308
pressure switch 40-671
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-799 40-1324
sensor tact
Switching pressure: 40-816
0.93 to 0.94 bar ab-
solute pressure
K019 Brake fluid level sen- 40-799 40-1324
sor 40-816
K020 Engine oil pressure 40-701 40-1324
switch 40-714
40-799
40-816
K021 Engine temperature 40-701 40-1324
sensor 40-714
40-816
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-799 40-1327
sensor tact
Switching pressure: 40-816
0.93 to 0.94 bar ab-
solute pressure
K024 Brake fluid level sen- 40-799 40-1327
sor 40-816
K025 Engine oil pressure 40-701 40-1327
switch 40-714
40-799
40-816

40-525
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K026 Engine temperature 40-701 40-1327
sensor 40-714
40-816
K030 Engine coolant tem- 40-701 40-1425
perature sensor 40-714
K031 Not used [LNK] 40-1425
K032 Turbine air tempera- 40-701 40-1425
ture/pressure sensor 40-714
K033 Not used [LNK] 40-1425
K034 Not used [LNK] 40-1425
K035 Camshaft speed 40-701 40-1425
sensor 40-714
K036 Fuel temperature 40-701 40-1425
sensor 40-714

Table 329
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K037 2.7659.097.0 Handbrake pressure 40-799 40-1331

CB A
switch
Between Pin 1 and 40-877
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1158
Pin 4: normally open
(NO) switch
K052 2.7659.097.0 Handbrake pressure 40-816 40-1392
CB A

switch
Between Pin 1 and 40-889
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1178
Pin 4: normally open
(NO) switch
K053 Operator present 40-816 40-1392
sensor in seat
K054 Pall filter [LNK] 40-1293
K055 Operator present 40-799 40-1331
sensor in seat
K056 MTA connector 40-671 40-1301
USA version
Table 330
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K002 Clutch pedal position 40-1199 40-1293
sensor 40-1192
K003 2.7099.996.0 Engine speed sen- This cannot be [LNK] 40-1296
sor checked using an
ordinary tester; use
the ART.
K004 2.7099.740.0/10 Shuttle sensor Pin 1 = power (Nomi- [LNK] 40-1296
nal 5.0V)
Pin 2 = ground
Pin 4 = analogue
signal

40-526
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K005 2.7099.800.0 Oil temperature sen- [LNK] 40-1296
sor
K006 2.7099.690.0/10 Clutch oil pressure Normally closed [LNK] 40-1296
switch (NC) contact
Switching pressure:
4 Bar
K007 PALL filter clogging [LNK] 40-1296
sensor
K008 PTO speed sensor 40-728 40-1300
40-743
K009 Stoll 40-852 40-1306
K010 Transmission filter 40-834 40-1306
clogging sensor 40-852
40-1199
40-1192
K011 2.7659.096.0/10 Dual traction sensor 40-834 40-1306

P=
XX
X
XX
XX

X
X

Between Pin 1 and 40-852

Pin 2: Normally
closed (NC) contact
Between Pin 2 and 40-1199
Pin 3: Normally open 40-1192
(NO) contact
K012 Transmission oil 40-834 40-1306
filter clogging pres- 40-852
sure switch 40-1199
40-1192
K013 Wheels speed sen- 40-834 40-1306
sor 40-852
40-1199
40-1192
K014 Services circuit 40-834 40-1306
alarm pressure 40-852
switch
K015 Hydraulic trailer 40-834 40-1306
braking valve pres- 40-852
sure switch 40-882
40-895
K016 Fuel level sensor 40-834 40-1306
40-852
K017 Air conditioning 40-683 40-1308
pressure switch 40-677
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-834 40-1324
sensor tact
Switching pressure: 40-852
0.93 to 0.94 bar ab-
solute pressure
K019 Brake fluid level sen- 40-834 40-1324
sor 40-852

40-527
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K020 Engine oil pressure 40-705 40-1324
switch 40-719
40-834
40-852
K021 Engine temperature 40-705 40-1324
sensor 40-719
40-852
K022 Operator present [LNK] 40-1410
sensor in seat
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-834 40-1327
sensor tact
Switching pressure: 40-852
0.93 to 0.94 bar ab-
solute pressure
K024 Brake fluid level sen- 40-834 40-1327
sor 40-852
K025 Engine oil pressure 40-705 40-1327
switch 40-719
40-834
40-852
K026 Engine temperature 40-705 40-1327
sensor 40-719
40-852
K027 2.7659.097.0 Handbrake pressure 40-852 40-1410
CB A

switch
Between Pin 1 and 40-895
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1192
Pin 4: normally open
(NO) switch
K030 Engine coolant tem- 40-705 40-1425
perature sensor 40-719
K031 Not used [LNK] 40-1425
K032 Turbine air tempera- 40-705 40-1425
ture/pressure sensor 40-719
K033 Not used [LNK] 40-1425
K034 Not used [LNK] 40-1425
K035 Camshaft speed 40-705 40-1425
sensor 40-719
K036 Fuel temperature 40-705 40-1425
sensor 40-719

40-528
Wiring diagrams
Table 331
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K038 2.7659.097.0 Handbrake pressure 40-834 40-1347

CB A
switch
Between Pin 1 and 40-882
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1199
Pin 4: normally open
(NO) switch
K039 Operator present 40-834 40-1347
sensor in seat
K054 Pall filter [LNK] 40-1293
K056 MTA connector 40-677 40-1301

40.2.62 - K - Sensors and transmitters (AGROFARM 410 -> ZKDW350200TD25001)

ITA version
Table 332
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K001 0.011.9428.0 Trailer braking low 40-877 40-1287
pressure switch

K002 Clutch pedal position 40-1158 40-1293

sensor 40-1231
K003 2.7099.996.0 Engine speed sen- This cannot be [LNK] 40-1296
sor checked using an
ordinary tester; use
the ART.
K004 2.7099.740.0/10 Shuttle sensor Pin 1 = power (Nomi- [LNK] 40-1296
nal 5.0V)
Pin 2 = ground
Pin 4 = analogue
signal
K005 2.7099.800.0 Oil temperature sen- [LNK] 40-1296
sor
K006 2.7099.690.0/10 Clutch oil pressure Normally closed [LNK] 40-1296
switch (NC) contact
Switching pressure:
4 Bar
K007 PALL filter clogging [LNK] 40-1296
sensor
K009 Stoll [LNK] 40-1306
K010 Transmission filter 40-799 40-1306
clogging sensor

40-529
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K011 2.7659.096.0/10 Dual traction sensor 40-799 40-1306

P=
XX
X
XX
XX

X
X
Between Pin 1 and 40-1158
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
K012 Transmission oil 40-799 40-1306
filter clogging pres- 40-1158
sure switch
K013 Wheels speed sen- 40-799 40-1306
sor 40-1158
[LNK]
K014 Services circuit 40-799 40-1306
alarm pressure
switch
K015 Hydraulic trailer 40-799 40-1306
braking valve pres- 40-877
sure switch
K016 Fuel level sensor 40-799 40-1306
K017 Air conditioning 40-665 40-1308
pressure switch 40-671
40-689
40-695
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-799 40-1324
sensor tact
Switching pressure: 40-870
0.93 to 0.94 bar ab-
solute pressure
K019 Brake fluid level sen- 40-799 40-1324
sor 40-870
K020 Engine oil pressure 40-701 40-1324
switch 40-710
40-870
40-799
K021 Engine temperature 40-701 40-1324
sensor 40-710
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-799 40-1327
sensor tact
Switching pressure: 40-870
0.93 to 0.94 bar ab-
solute pressure
K024 Brake fluid level sen- 40-799 40-1327
sor 40-870
K025 Engine oil pressure 40-701 40-1327
switch 40-710
40-799
40-870
K026 Engine temperature 40-701 40-1327
sensor 40-710

40-530
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K030 Engine coolant tem- 40-701 40-1425
perature sensor 40-710
K031 Not used [LNK] 40-1425
K032 Turbine air tempera- 40-701 40-1425
ture/pressure sensor 40-710
K033 Not used [LNK] 40-1425
K034 Not used [LNK] 40-1425
K035 Camshaft speed 40-701 40-1425
sensor 40-710
K036 Fuel temperature 40-701 40-1425
sensor 40-710

Table 333
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K037 2.7659.097.0 Handbrake pressure 40-799 40-1331

CB A
switch
Between Pin 1 and 40-877
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1158
Pin 4: normally open
(NO) switch
K040 2.7659.097.0 Handbrake pressure 1 40-870 40-1365
switch
4

Between Pin 1 and 40-902

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
K041 Operator present 40-870 40-1365
sensor in seat
K042 Lift position sensor 40-1269 40-1382
K043 Lift draft sensor 40-1269 40-1382
K044 Services circuit 40-870 40-1385
alarm pressure
switch
K045 Wheels speed sen- 40-870 40-1385
sor 40-1231
K046 2.7099.960.0 Hydraulic trailer 40-870 40-1385
P=
XX
XX X

braking valve pres-

XX

X
X

sure switch

Normally closed 40-902

(NC) contact
Switching pressure:
11 bar

40-531
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K047 2.7659.096.0/10 Dual traction sensor 40-870 40-1385

CB A
Between Pin 1 and 40-1231
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
K048 Fuel level sensor 40-870 40-1385
K049 Transmission oil 40-870 40-1385
filter clogging pres- 40-1231
sure switch
K050 Transmission filter 40-870 40-1385
clogging sensor 40-1231
K051 Stoll [LNK] 40-1385
K054 Pall filter [LNK] 40-1293
K055 Operator present 40-799 40-1331
sensor in seat
K056 MTA connector 40-671 40-1301
USA version
Table 334
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K001 0.011.9428.0 Trailer braking low 40-882 40-1287
pressure switch

K002 Clutch pedal position 40-1199 40-1293

sensor 40-1231
K003 2.7099.996.0 Engine speed sen- This cannot be [LNK] 40-1296
sor checked using an
ordinary tester; use
the ART.
K004 2.7099.740.0/10 Shuttle sensor Pin 1 = power (Nomi- [LNK] 40-1296
nal 5.0V)
Pin 2 = ground
Pin 4 = analogue
signal
K005 2.7099.800.0 Oil temperature sen- [LNK] 40-1296
sor
K006 2.7099.690.0/10 Clutch oil pressure Normally closed [LNK] 40-1296
switch (NC) contact
Switching pressure:
4 Bar
K007 PALL filter clogging [LNK] 40-1296
sensor
K008 PTO speed sensor 40-728 40-1300
40-734
K009 Stoll [LNK] 40-1306
K010 Transmission filter 40-834 40-1306
clogging sensor

40-532
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K011 2.7659.096.0/10 Dual traction sensor 40-834 40-1306

P=
XX
X
XX
XX

X
X
Between Pin 1 and 40-1199
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
K012 Transmission oil 40-834 40-1306
filter clogging pres- 40-1199
[LNK]
K013 Wheels speed sen- 40-834 40-1306
sor 40-1199
K014 Services circuit 40-834 40-1306
alarm pressure
switch
K015 Hydraulic trailer 40-834 40-1306
braking valve pres- 40-882
sure switch
K016 Fuel level sensor 40-834 40-1306
K017 Air conditioning 40-683 40-1308
pressure switch 40-689
40-695
40-677
K018 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-834 40-1324
sensor tact
Switching pressure: 40-870
0.93 to 0.94 bar ab-
solute pressure
K019 Brake fluid level sen- 40-834 40-1324
sor 40-870
K020 Engine oil pressure 40-705 40-1324
switch 40-710
40-834
40-870
K021 Engine temperature 40-705 40-1324
sensor 40-710
K023 2.7099.320.0/10 Air cleaner clogged Normally open con- 40-834 40-1327
sensor tact
Switching pressure: 40-870
0.93 to 0.94 bar ab-
solute pressure
K024 Brake fluid level sen- 40-834 40-1327
sor 40-870
K025 Engine oil pressure 40-705 40-1327
switch 40-710
40-834
40-870
K026 Engine temperature 40-705 40-1327
sensor 40-710
K028 Antifrost thermostat [LNK] 40-1318

40-533
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K030 Engine coolant tem- 40-705 40-1425
perature sensor 40-710
K031 Not used [LNK] 40-1425
K032 Turbine air tempera- 40-705 40-1425
ture/pressure sensor 40-710
K033 Not used [LNK] 40-1425
K034 Not used [LNK] 40-1425
K035 Camshaft speed 40-705 40-1425
sensor 40-710
K036 Fuel temperature 40-705 40-1425
sensor 40-710

Table 335
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K038 2.7659.097.0 Handbrake pressure 40-834 40-1347

CB A
switch
Between Pin 1 and 40-882
Pin 2: normally
closed (NC) switch
Between Pin 3 and 40-1199
Pin 4: normally open
(NO) switch
K039 Operator present 40-834 40-1347
sensor in seat
K040 2.7659.097.0 Handbrake pressure 1 40-870 40-1365
switch
4

Between Pin 1 and 40-902

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
K041 Operator present 40-870 40-1365
sensor in seat
K042 Lift position sensor 40-1269 40-1382
K043 Lift draft sensor 40-1269 40-1382
K044 Services circuit 40-870 40-1385
alarm pressure
switch
K045 Wheels speed sen- 40-870 40-1385
sor 40-1231
K046 2.7099.960.0 Hydraulic trailer 40-870 40-1385
P=
XX
XX X

braking valve pres-

XX

X
X

sure switch

Normally closed 40-902

(NC) contact
Switching pressure:
11 bar

40-534
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
K047 2.7659.096.0/10 Dual traction sensor 40-870 40-1385

CB A
Between Pin 1 and 40-1231
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
K048 Fuel level sensor 40-870 40-1385
K049 Transmission oil 40-870 40-1385
filter clogging pres- 40-1231
sure switch
K050 Transmission filter 40-870 40-1385
clogging sensor 40-1231
K051 Stoll [LNK] 40-1385
K054 Pall filter [LNK] 40-1293
K056 MTA connector 40-677 40-1301

40.2.63 - L - Electromagnets and solenoid valves (AGROFARM 410 -> ZKD-

W350200TD25001)
Table 336
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
L001 Front PTO control 40-723 40-1281
solenoid valve 40-728
40-738
40-743
L005 Trailer solenoid 40-791 40-1306
valve 40-807
40-826
40-843
40-877
40-882
40-889
40-895
40-1145
40-1166
40-1186
40-1206
L006 Differential lock con- 40-791 40-1306
trol solenoid valve 40-807
40-826
40-843
40-1145
40-1166
40-1186
40-1206
L007 4WD control sole- 40-791 40-1306
noid valve 40-807
40-826
40-843
40-1145
40-1166
40-1186
40-1206

40-535
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
L008 Rear PTO control 40-723 40-1306
solenoid valve 40-728
40-738
40-743
40-807
40-843
L009 HI/LO solenoid valve 40-791 40-1306
40-807
40-826
40-843
40-1145
40-1166
40-1186
40-1206

40.2.64 - L - Electromagnets and solenoid valves (AGROFARM 420 -> ZKD-

W390200TD25001)
Table 337
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
L001 Front PTO control 40-723 40-1281
solenoid valve 40-728
40-738
40-743
L005 Trailer solenoid 40-791 40-1306
valve 40-807
40-826
40-843
40-877
40-882
40-889
40-895
40-1145
40-1166
40-1186
40-1206
L006 Differential lock con- 40-791 40-1306
trol solenoid valve 40-807
40-826
40-843
40-1145
40-1166
40-1186
40-1206
L007 4WD control sole- 40-791 40-1306
noid valve 40-807
40-826
40-843
40-1145
40-1166
40-1186
40-1206
L008 Rear PTO control 40-723 40-1306
solenoid valve 40-728
40-738
40-743
40-807
40-843

40-536
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
L009 HI/LO solenoid valve 40-791 40-1306
40-807
40-826
40-843
40-1145
40-1166
40-1186
40-1206
L020 Distributor COM so- 40-1237 40-1388
lenoid valve 40-1240
L021 Auxiliary distributors 40-1237 40-1388
40-1240
L022 Auxiliary distributor 40-1237 40-1388
40-1240

40.2.65 - L - Electromagnets and solenoid valves (AGROFARM 430 -> ZKD-

W430200TD25001)
Table 338
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
L001 Front PTO control 40-723 40-1281
solenoid valve 40-728
40-738
40-743
40-734
L005 Trailer solenoid 40-791 40-1306
valve 40-807
40-826
40-843
40-877
40-882
40-889
40-895
40-1145
40-1166
40-1186
40-1206
L006 Differential lock con- 40-791 40-1306
trol solenoid valve 40-807
40-826
40-843
40-1145
40-1166
40-1186
40-1206
L007 4WD control sole- 40-791 40-1306
noid valve 40-807
40-826
40-843
40-1145
40-1166
40-1186
40-1206
L008 Rear PTO control 40-723 40-1306
solenoid valve 40-728
40-738
40-743
40-807
40-843

40-537
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
L009 HI/LO solenoid valve 40-791 40-1306
40-807
40-826
40-843
40-1145
40-1166
40-1186
40-1206
L011 Lift up solenoid valve 40-1269 40-1382
L012 Lift down solenoid 40-1269 40-1382
valve
L013 Distributor COM so- 40-1243 40-1384
lenoid valve
L014 Auxiliary distributor 40-1243 40-1384
L015 Auxiliary distributor 40-1243 40-1384
L016 HI/LO solenoid valve 40-862 40-1385
40-1226
L017 Rear PTO control 40-734 40-1385
solenoid valve
L018 4WD control sole- 40-1226 40-1385
noid valve
L019 Differential lock con- 40-1226 40-1385
trol solenoid valve
L020 Distributor COM so- 40-1237 40-1388
lenoid valve 40-1240
L021 Auxiliary distributors 40-1237 40-1388
40-1240
L022 Auxiliary distributor 40-1237 40-1388
40-1240

40.2.66 - L - Electromagnets and solenoid valves (AGROFARM 410 -> ZKD-

W470200TD30001)
Table 339
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
L001 Front PTO control 40-723 40-1281
solenoid valve 40-728
40-738
40-743
L004 Proportional sole- 40-1151 40-1296
noid valve 40-1171
40-1192
40-1211
L005 Trailer solenoid 40-799 40-1306
valve 40-816
40-834
40-852
40-877
40-882
40-889
40-895
40-1151
40-1171
40-1192
40-1211

40-538
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
L006 Differential lock con- 40-799 40-1306
trol solenoid valve 40-816
40-834
40-852
40-1151
40-1171
40-1192
40-1211
L007 4WD control sole- 40-799 40-1306
noid valve 40-816
40-834
40-852
40-1151
40-1171
40-1192
40-1211
L008 Rear PTO control 40-723 40-1306
solenoid valve 40-728
40-738
40-743
40-816
40-852
L009 HI/LO solenoid valve 40-799 40-1306
40-816
40-834
40-852
40-1151
40-1171
40-1192
40-1211

40.2.67 - L - Electromagnets and solenoid valves (AGROFARM 420 -> ZKD-

W510200TD30001)
Table 340
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
L001 Front PTO control 40-723 40-1281
solenoid valve 40-728
40-738
40-743
L002 Forward drive selec- 40-1178 40-1295
tion solenoid valve 40-1199
40-1218
L003 Reverse drive selec- [LNK] 40-1295
tion solenoid valve
L004 Proportional sole- 40-1158 40-1296
noid valve 40-1178
40-1199
40-1218

40-539
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
L005 Trailer solenoid 40-799 40-1306
valve 40-816
40-834
40-852
40-877
40-882
40-889
40-895
40-1158
40-1178
40-1199
40-1218
L006 Differential lock con- 40-799 40-1306
trol solenoid valve 40-816
40-834
40-852
40-1158
40-1178
40-1199
40-1218
L007 4WD control sole- 40-799 40-1306
noid valve 40-816
40-834
40-852
40-1158
40-1178
40-1199
40-1218
L008 Rear PTO control 40-723 40-1306
solenoid valve 40-728
40-738
40-743
40-816
40-852
L009 HI/LO solenoid valve 40-799 40-1306
40-816
40-834
40-852
40-1158
40-1178
40-1199
40-1218
L020 Distributor COM so- 40-1237 40-1388
lenoid valve 40-1240
L021 Auxiliary distributors 40-1237 40-1388
40-1240
L022 Auxiliary distributor 40-1237 40-1388
40-1240

40-540
Wiring diagrams
40.2.68 - L - Electromagnets and solenoid valves (AGROFARM 430 -> ZKD-
W550200TD30001)
Table 341
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
L001 Front PTO control 40-723 40-1281
solenoid valve 40-728
40-734
L002 Forward drive selec- 40-1199 40-1295
tion solenoid valve 40-1231
L003 Reverse drive selec- [LNK] 40-1295
tion solenoid valve
L004 Proportional sole- 40-1158 40-1296
noid valve 40-1199
40-1231
L005 Trailer solenoid 40-799 40-1306
valve 40-834
40-877
40-882
40-1158
40-1199
L006 Differential lock con- 40-799 40-1306
trol solenoid valve 40-834
40-1158
40-1199
L007 4WD control sole- 40-799 40-1306
noid valve 40-834
40-1158
40-1199
L008 Rear PTO control 40-723 40-1306
solenoid valve 40-728
L009 HI/LO solenoid valve 40-799 40-1306
40-834
40-1158
40-1199
L010 Trailer parking brake 40-870 40-1324
control solenoid 40-902
valve
L011 Lift up solenoid valve 40-1269 40-1382
L012 Lift down solenoid 40-1269 40-1382
valve
L013 Distributor COM so- 40-1243 40-1384
lenoid valve
L014 Auxiliary distributor 40-1243 40-1384
L015 Auxiliary distributor 40-1243 40-1384
L016 HI/LO solenoid valve 40-870 40-1385
40-1231
L017 Rear PTO control 40-734 40-1385
solenoid valve
L018 4WD control sole- 40-1231 40-1385
noid valve
L019 Differential lock con- 40-1231 40-1385
trol solenoid valve
L020 Distributor COM so- 40-1237 40-1388
lenoid valve 40-1240
L021 Auxiliary distributors 40-1237 40-1388
40-1240
L022 Auxiliary distributor 40-1237 40-1388
40-1240

40-541
 Wiring diagrams
40.2.69 - M - Electrical/electronic devices, Flasher units and Timers (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001)
ITA version
Table 342
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M001 2.8519.115.0/20 ECU Rear PTO 40-723 40-1331
40-791
M002 Engine control unit 40-596 40-1331
40-701
40-701
M003 Engine control unit 40-596 40-1331
40-1145
40-791
40-701
40-1247
40-701
M004 25A socket [LNK] 40-1331
M005 2.8519.115.0/20 ECU Front PTO 40-723 40-1331
40-791
M012 ECU Rear PTO 40-738 40-1392
40-807
M013 Engine control unit 40-621 40-1392
40-714
40-714
M014 Engine control unit 40-621 40-1392
40-1166
40-807
40-714
40-1255
40-714
M015 2.8519.115.0/20 ECU Front PTO 40-738 40-1392
40-807
M019 ECU Hazard warn- 40-791 40-1331
ing lights 40-915
M020 ECU Hazard warn- 40-807 40-1392
ing lights 40-953

USA version
Table 343
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M006 2.8519.114.0/10 ECU PTO 40-728 40-1347
40-826
M007 Engine control unit 40-604 40-1347
40-705
M008 Engine control unit 40-604 40-1347
40-826
40-1186
40-1247
40-705
M016 2.8519.115.0/20 ECU Rear PTO 40-743 40-1410
40-843
M017 Engine control unit 40-629 40-1410
40-719
M018 Engine control unit 40-629 40-1410
40-843
40-1206
40-1255
40-719

40-542
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M022 ECU Hazard warn- 40-826 40-1347
ing lights 40-928
M023 ECU Hazard warn- 40-843 40-1410
ing lights

40.2.70 - M - Electrical/electronic devices, Flasher units and Timers (AGROFARM 430 ->
ZKDW430200TD25001)
ITA version
Table 344
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M001 2.8519.115.0/20 ECU Rear PTO 40-723 40-1331
40-791
M002 Engine control unit 40-596 40-1331
40-701
40-701
M003 Engine control unit 40-596 40-1331
40-1145
40-791
40-701
40-1247
40-701
M004 25A socket [LNK] 40-1331
M005 2.8519.115.0/20 ECU Front PTO 40-723 40-1331
40-791
M009 Engine control unit 40-613 40-1365
40-710
M010 Engine control unit 40-613 40-1365
40-862
40-1226
40-1262
40-710
M011 HLHP unit 40-862 40-1365
40-1243
40-1262
40-1226
M012 ECU Rear PTO 40-738 40-1392
40-807
M013 Engine control unit 40-621 40-1392
40-714
40-714
M014 Engine control unit 40-621 40-1392
40-1166
40-807
40-714
40-1255
40-714
M015 2.8519.115.0/20 ECU Front PTO 40-738 40-1392
40-807
M019 ECU Hazard warn- 40-791 40-1331
ing lights 40-915
M020 ECU Hazard warn- 40-807 40-1392
ing lights 40-953
M021 ECU Hazard warn- 40-862 40-1365
ing lights 40-942
M024 Electronic lift con- 40-862 40-1365
sole

40-543
 Wiring diagrams
USA version
Table 345
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M006 2.8519.114.0/10 ECU PTO 40-728 40-1347
40-826
M007 Engine control unit 40-604 40-1347
40-705
M008 Engine control unit 40-604 40-1347
40-826
40-1186
40-1247
40-705
M009 Engine control unit 40-613 40-1365
40-710
M010 Engine control unit 40-613 40-1365
40-862
40-1226
40-1262
40-710
M011 HLHP unit 40-862 40-1365
40-1243
40-1262
40-1226
M016 2.8519.115.0/20 ECU Rear PTO 40-743 40-1410
40-843
M017 Engine control unit 40-629 40-1410
40-719
M018 Engine control unit 40-629 40-1410
40-843
40-1206
40-1255
40-719
M021 ECU Hazard warn- 40-862 40-1365
ing lights 40-942
M022 ECU Hazard warn- 40-826 40-1347
ing lights 40-928
M023 ECU Hazard warn- 40-843 40-1410
ing lights 40-964
M024 Electronic lift con- 40-862 40-1365
sole

40.2.71 - M - Electrical/electronic devices, Flasher units and Timers (AGROFARM 410 ->
ZKDW470200TD30001)
ITA version
Table 346
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M001 2.8519.115.0/20 ECU Rear PTO 40-723 40-1331
40-799
M002 Engine control unit 40-600 40-1331
40-701
40-701
M003 Engine control unit 40-600 40-1331
40-1151
40-799
40-701
40-1250
40-701
M004 25A socket [LNK] 40-1331

40-544
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M005 2.8519.115.0/20 ECU Front PTO 40-723 40-1331
40-799
M012 ECU Rear PTO 40-738 40-1392
40-816
M013 Engine control unit 40-625 40-1392
40-714
40-714
M014 Engine control unit 40-625 40-1392
40-1171
40-816
40-714
40-1258
40-714
M015 2.8519.115.0/20 ECU Front PTO 40-738 40-1392
40-816
M019 ECU Hazard warn- 40-799 40-1331
ing lights 40-922
M020 ECU Hazard warn- 40-816 40-1392
ing lights 40-959

USA version
Table 347
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M006 2.8519.114.0/10 ECU PTO 40-728 40-1347
40-834
M007 Engine control unit 40-608 40-1347
40-705
M008 Engine control unit 40-608 40-1347
40-834
40-1192
40-1250
40-705
M016 2.8519.115.0/20 ECU Rear PTO 40-743 40-1410
40-852
M017 Engine control unit 40-633 40-1410
40-719
M018 Engine control unit 40-633 40-1410
40-852
40-1211
40-1258
40-719
M022 ECU Hazard warn- 40-834 40-1347
ing lights 40-935
M023 ECU Hazard warn- 40-852 40-1410
ing lights 40-970

40.2.72 - M - Electrical/electronic devices, Flasher units and Timers (AGROFARM 420 ->
ZKDW510200TD30001)
ITA version
Table 348
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M001 2.8519.115.0/20 ECU Rear PTO 40-723 40-1331
40-799
M002 Engine control unit 40-600 40-1331
40-701
40-701

40-545
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M003 Engine control unit 40-600 40-1331
40-1158
40-799
40-701
40-1250
40-701
M004 25A socket [LNK] 40-1331
M005 2.8519.115.0/20 ECU Front PTO 40-723 40-1331
40-799
M012 ECU Rear PTO 40-738 40-1392
40-816
M013 Engine control unit 40-625 40-1392
40-714
40-714
M014 Engine control unit 40-625 40-1392
40-1178
40-816
40-714
40-1258
40-714
M015 2.8519.115.0/20 ECU Front PTO 40-738 40-1392
40-816
M019 ECU Hazard warn- 40-799 40-1331
ing lights 40-922
M020 ECU Hazard warn- 40-816 40-1392
ing lights 40-959

USA version
Table 349
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M006 2.8519.114.0/10 ECU PTO 40-728 40-1347
40-834
M007 Engine control unit 40-608 40-1347
40-705
M008 Engine control unit 40-608 40-1347
40-834
40-1199
40-1250
40-705
M016 2.8519.115.0/20 ECU Rear PTO 40-743 40-1410
40-852
M017 Engine control unit 40-633 40-1410
40-719
M018 Engine control unit 40-633 40-1410
40-852
40-1218
40-1258
40-719
M022 ECU Hazard warn- 40-834 40-1347
ing lights 40-935
M023 ECU Hazard warn- 40-852 40-1410
ing lights 40-970

40-546
Wiring diagrams
40.2.73 - M - Electrical/electronic devices, Flasher units and Timers (AGROFARM 430 ->
ZKDW550200TD30001)
ITA version
Table 350
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M001 2.8519.115.0/20 ECU Rear PTO 40-723 40-1331
40-799
M002 Engine control unit 40-600 40-1331
40-701
40-701
M003 Engine control unit 40-600 40-1331
40-1158
40-799
40-701
40-1250
40-701
M004 25A socket [LNK] 40-1331
M005 2.8519.115.0/20 ECU Front PTO 40-723 40-1331
40-799
M009 Engine control unit 40-616 40-1365
40-710
M010 Engine control unit 40-616 40-1365
40-870
40-1231
40-1266
40-710
M011 HLHP unit 40-870 40-1365
40-1243
40-1266
40-734
40-1269
40-1231
M012 ECU Rear PTO 40-738 40-1392
40-807
M013 Engine control unit 40-621 40-1392
40-714
40-714
M014 Engine control unit 40-621 40-1392
40-1166
40-807
40-714
40-1255
40-714
M015 2.8519.115.0/20 ECU Front PTO 40-738 40-1392
40-807
M019 ECU Hazard warn- 40-799 40-1331
ing lights 40-922
M020 ECU Hazard warn- 40-807 40-1392
ing lights 40-953
M021 ECU Hazard warn- 40-870 40-1365
ing lights 40-948
M024 Electronic lift con- 40-870 40-1365
sole 40-1269

40-547
 Wiring diagrams
USA version
Table 351
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
M006 2.8519.114.0/10 ECU PTO 40-728 40-1347
40-834
M007 Engine control unit 40-608 40-1347
40-705
M008 Engine control unit 40-608 40-1347
40-834
40-1199
40-1250
40-705
M009 Engine control unit 40-616 40-1365
40-710
M010 Engine control unit 40-616 40-1365
40-870
40-1231
40-1266
40-710
M011 HLHP unit 40-870 40-1365
40-1243
40-1266
40-734
40-1269
40-1231
M016 2.8519.115.0/20 ECU Rear PTO 40-743 40-1410
40-843
M017 Engine control unit 40-629 40-1410
40-719
M018 Engine control unit 40-629 40-1410
40-843
40-1206
40-1255
40-719
M021 ECU Hazard warn- 40-870 40-1365
ing lights 40-948
M022 ECU Hazard warn- 40-834 40-1347
ing lights 40-935
M023 ECU Hazard warn- 40-843 40-1410
ing lights 40-964
M024 Electronic lift con- 40-870 40-1365
sole 40-1269

40.2.74 - N - Electric motors and actuators (AGROFARM 410 -> ZKDW350200TD25001,

AGROFARM 420 -> ZKDW390200TD25001)
ITA version
Table 352
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N001 Electric fan 40-641 40-1274
N002 Electric fan 40-665 40-1275
N003 Windscreen wiper 40-755 40-1276
motor 40-758
N004 Windscreen wiper 40-750 40-1279
motor
N005 Starter motor “+30” 40-596 40-1329
40-701
40-714
40-621

40-548
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N006 Rear window wiper 40-755 40-1300
motor 40-758
N008 RH electric fan 40-671 40-1301
N009 LH electric fan 40-671 40-1301
N010 Rear window wiper 40-750 40-1301
motor
N012 Electric fan [LNK] 40-1318
N014 Front screenwash 40-750 40-1331
pump 40-758
40-755
N015 Rear screenwash 40-750 40-1331
pump 40-758
40-755
N016 Air conditioning 40-665 40-1324
compressor 40-807
40-671
N017 Air conditioning 40-665 40-1327
compressor 40-807
40-671
USA version
Table 353
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N001 Electric fan 40-652 40-1274
N002 Electric fan 40-683 40-1275
N003 Windscreen wiper 40-769 40-1276
motor 40-758
N004 Windscreen wiper 40-764 40-1279
motor
N005 Starter motor “+30” 40-604 40-1329
40-705
40-719
40-629
N006 Rear window wiper 40-769 40-1300
motor 40-758
N007 Windscreen washer 40-764 40-1347
pump 40-769
N008 RH electric fan 40-677 40-1301
N009 LH electric fan 40-677 40-1301
N010 Rear window wiper 40-764 40-1301
motor
N011 Rear screen washer 40-764 40-1347
pump
N012 Electric fan [LNK] 40-1318
N016 Air conditioning 40-683 40-1324
compressor 40-843
40-677
N017 Air conditioning 40-683 40-1327
compressor 40-843
40-677

40.2.75 - N - Electric motors and actuators (AGROFARM 430 -> ZKDW430200TD25001)

40-549
 Wiring diagrams
ITA version
Table 354
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N001 Electric fan 40-641 40-1274
40-660
N002 Electric fan 40-665 40-1275
40-689
N003 Windscreen wiper 40-755 40-1276
motor 40-787
40-758
N004 Windscreen wiper 40-750 40-1279
motor
N005 Starter motor “+30” 40-596 40-1329
40-701
40-710
40-613
40-714
40-621
N006 Rear window wiper 40-755 40-1300
motor 40-787
40-758
N008 RH electric fan 40-671 40-1301
40-695
N009 LH electric fan 40-671 40-1301
40-695
N010 Rear window wiper 40-750 40-1301
motor
N012 Electric fan [LNK] 40-1318
N013 Actuator 40-710 40-1425
N014 Front screenwash 40-750 40-1331
pump 40-758
40-755
N015 Rear screenwash 40-750 40-1331
pump 40-758
40-755
N016 Air conditioning 40-665 40-1324
compressor 40-807
40-695
40-689
40-671
N017 Air conditioning 40-665 40-1327
compressor 40-807
40-695
40-689
40-671
N019 Windscreen washer [LNK] 40-1365
pump
N020 Rear screen washer [LNK] 40-1365
pump
USA version
Table 355
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N001 Electric fan 40-652 40-1274
40-660
N002 Electric fan 40-683 40-1275
40-689
N003 Windscreen wiper 40-769 40-1276
motor 40-787
40-758

40-550
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N004 Windscreen wiper 40-764 40-1279
motor
N005 Starter motor “+30” 40-604 40-1329
40-710
40-613
40-705
40-719
40-629
N006 Rear window wiper 40-769 40-1300
motor 40-787
40-758
N007 Windscreen washer 40-764 40-1347
pump 40-769
N008 RH electric fan 40-677 40-1301
40-695
N009 LH electric fan 40-677 40-1301
40-695
N010 Rear window wiper 40-764 40-1301
motor
N011 Rear screen washer 40-764 40-1347
pump
N012 Electric fan [LNK] 40-1318
N013 Actuator 40-710 40-1425
N016 Air conditioning 40-683 40-1324
compressor 40-689
40-843
40-695
40-677
N017 Air conditioning 40-683 40-1327
compressor 40-689
40-843
40-695
40-677
N019 Windscreen washer [LNK] 40-1365
pump
N020 Rear screen washer [LNK] 40-1365
pump

40-551
 Wiring diagrams
40.2.76 - N - Electric motors and actuators (AGROFARM 410 -> ZKDW470200TD30001,
AGROFARM 420 -> ZKDW510200TD30001)
ITA version
Table 356
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N001 Electric fan [LNK] 40-1274
N002 Electric fan 40-665 40-1275
N003 Windscreen wiper 40-755 40-1276
motor
N004 Windscreen wiper 40-750 40-1279
motor
N005 Starter motor “+30” 40-600 40-1329
40-701
40-714
40-625
N006 Rear window wiper 40-755 40-1300
motor
N008 RH electric fan 40-671 40-1301
N009 LH electric fan 40-671 40-1301
N010 Rear window wiper 40-750 40-1301
motor
N013 Actuator 40-714 40-1425
N014 Front screenwash 40-750 40-1331
pump 40-755
N015 Rear screenwash 40-750 40-1331
pump 40-755
N016 Air conditioning 40-665 40-1324
compressor 40-816
40-671
N017 Air conditioning 40-665 40-1327
compressor 40-816
40-671
USA version
Table 357
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N001 Electric fan [LNK] 40-1274
N002 Electric fan 40-683 40-1275
N003 Windscreen wiper 40-769 40-1276
motor
N004 Windscreen wiper 40-764 40-1279
motor
N005 Starter motor “+30” 40-608 40-1329
40-705
40-719
40-633
N006 Rear window wiper 40-769 40-1300
motor
N007 Windscreen washer 40-764 40-1347
pump 40-769
N008 RH electric fan 40-677 40-1301
N009 LH electric fan 40-677 40-1301
N010 Rear window wiper 40-764 40-1301
motor
N011 Rear screen washer 40-764 40-1347
pump
N013 Actuator 40-719 40-1425

40-552
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N016 Air conditioning 40-683 40-1324
compressor 40-852
40-677
N017 Air conditioning 40-683 40-1327
compressor 40-852
40-677

40.2.77 - N - Electric motors and actuators (AGROFARM 430 -> ZKDW550200TD30001)

ITA version
Table 358
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N001 Electric fan 40-660 40-1274
N002 Electric fan 40-665 40-1275
40-689
N003 Windscreen wiper 40-755 40-1276
motor 40-783
N004 Windscreen wiper 40-750 40-1279
motor 40-778
N005 Starter motor “+30” 40-600 40-1329
40-701
40-710
40-616
N006 Rear window wiper 40-755 40-1300
motor 40-783
N008 RH electric fan 40-671 40-1301
40-695
N009 LH electric fan 40-671 40-1301
40-695
N010 Rear window wiper 40-750 40-1301
motor 40-778
N013 Actuator 40-710 40-1425
N014 Front screenwash 40-750 40-1331
pump 40-755
N015 Rear screenwash 40-750 40-1331
pump 40-755
N016 Air conditioning 40-665 40-1324
compressor 40-816
40-695
40-689
40-671
N017 Air conditioning 40-665 40-1327
compressor 40-816
40-695
40-689
40-671
N019 Windscreen washer 40-778 40-1365
pump 40-783
N020 Rear screen washer 40-778 40-1365
pump 40-783

USA version
Table 359
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N001 Electric fan [LNK] 40-1274
N002 Electric fan 40-683 40-1275
40-689

40-553
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
N003 Windscreen wiper 40-769 40-1276
motor 40-783
N004 Windscreen wiper 40-764 40-1279
motor 40-778
N005 Starter motor “+30” 40-608 40-1329
40-710
40-616
40-705
N006 Rear window wiper 40-769 40-1300
motor 40-783
N007 Windscreen washer 40-764 40-1347
pump 40-769
N008 RH electric fan 40-677 40-1301
40-695
N009 LH electric fan 40-677 40-1301
40-695
N010 Rear window wiper 40-764 40-1301
motor 40-778
N011 Rear screen washer 40-764 40-1347
pump
N013 Actuator 40-710 40-1425
N016 Air conditioning 40-683 40-1324
compressor 40-689
40-852
40-695
40-677
N017 Air conditioning 40-683 40-1327
compressor 40-689
40-852
40-695
40-677
N019 Windscreen washer 40-778 40-1365
pump
N020 Rear screen washer 40-778 40-1365
pump

40-554
Wiring diagrams
40.2.78 - O - Resistors and rheostats (AGROFARM 410 -> ZKDW350200TD25001, AGRO-
FARM 420 -> ZKDW390200TD25001)
Table 360
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
O001 Resistor 40-641 40-1274
40-652
O002 Resistor 40-665 40-1275
40-683
O003 LH resistor 40-671 40-1301
40-677
O004 RH resistor 40-671 40-1301
40-677
O005 Blower speed resis- [LNK] 40-1318
tor

40.2.79 - O - Resistors and rheostats (AGROFARM 430 -> ZKDW430200TD25001)

Table 361
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
O001 Resistor 40-641 40-1274
40-660
40-652
O002 Resistor 40-665 40-1275
40-689
40-683
O003 LH resistor 40-671 40-1301
40-695
40-677
O004 RH resistor 40-671 40-1301
40-695
40-677
O005 Blower speed resis- [LNK] 40-1318
tor

40.2.80 - O - Resistors and rheostats (AGROFARM 410 -> ZKDW470200TD30001, AGRO-

FARM 420 -> ZKDW510200TD30001)
Table 362
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
O001 Resistor [LNK] 40-1274
O002 Resistor 40-665 40-1275
40-683
O003 LH resistor 40-671 40-1301
40-677
O004 RH resistor 40-671 40-1301
40-677

40.2.81 - O - Resistors and rheostats (AGROFARM 430 -> ZKDW550200TD30001)

Table 363
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
O001 Resistor [LNK] 40-1274
O002 Resistor 40-665 40-1275
40-689
40-683
O003 LH resistor 40-671 40-1301
40-695
40-677

40-555
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
O004 RH resistor 40-671 40-1301
40-695
40-677
O005 Blower speed resis- [LNK] 40-1318
tor

40.2.82 - P - Various services (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM

420 -> ZKDW390200TD25001)
ITA version
Table 364
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P002 0.011.7543.3/30 Radio 40-1099 40-1301
P003 0.011.7543.3/30 Radio 40-1099 40-1301
P004 0.011.5631.3 LH loudspeaker 40-1099 40-1301
P005 0.011.5631.3 RH loudspeaker 40-1099 40-1301
P006 Trailer socket 40-807 40-1306
40-877
40-889
40-915
40-953
P007 Air conditioner heat 40-665 40-1308
exchanger fan 40-671
P008 Auxiliary conditioner 40-665 40-1308
heat exchanger fan 40-671
P009 0.011.7543.3/30 Radio [LNK] 40-1318
P010 Clock [LNK] 40-1318
P011 0.011.7543.3/30 Radio [LNK] 40-1388
P012 Clock [LNK] 40-1388
P013 Air sprung seat 40-1099 40-1279
P014 8A socket [LNK] 40-1331
P015 CAN socket 40-1247 40-1331
P025 2.7099.770.0 Cigarette lighter 40-1130 40-1392
P026 CAN socket 40-1255 40-1392
P027 25A socket [LNK] 40-1392
P032 Wiring connector for 40-1130 40-1392
seat wiring loom
P034 2.7099.770.0 Cigarette lighter 40-1099 40-1331
USA version
Table 365
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P002 0.011.7543.3/30 Radio 40-1110 40-1301
P003 0.011.7543.3/30 Radio 40-1110 40-1301
P004 0.011.5631.3 LH loudspeaker 40-1110 40-1301
P005 0.011.5631.3 RH loudspeaker 40-1110 40-1301
P006 Trailer socket 40-843 40-1306
40-882
40-895
40-928
P007 Air conditioner heat 40-683 40-1308
exchanger fan 40-677
P008 Auxiliary conditioner 40-683 40-1308
heat exchanger fan 40-677
P009 0.011.7543.3/30 Radio [LNK] 40-1318
P010 Clock [LNK] 40-1318
P011 0.011.7543.3/30 Radio [LNK] 40-1388
P012 Clock [LNK] 40-1388

40-556
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P013 Air sprung seat [LNK] 40-1279
P016 8A socket [LNK] 40-1347
P017 CAN socket 40-1247 40-1347
P018 25A socket [LNK] 40-1347
P028 2.7099.770.0 Cigarette lighter 40-1137 40-1410
P029 CAN socket 40-1255 40-1410
P030 25A socket [LNK] 40-1410
P031 Wiring connector for 40-1110 40-1347
seat wiring loom
P033 Wiring connector for 40-1137 40-1410
seat wiring loom
P035 2.7099.770.0 Cigarette lighter 40-1110 40-1347

40.2.83 - P - Various services (AGROFARM 430 -> ZKDW430200TD25001)

ITA version
Table 366
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P002 0.011.7543.3/30 Radio 40-1099 40-1301
40-1120
P003 0.011.7543.3/30 Radio 40-1099 40-1301
40-1120
P004 0.011.5631.3 LH loudspeaker 40-1099 40-1301
40-1120
P005 0.011.5631.3 RH loudspeaker 40-1099 40-1301
40-1120
P006 Trailer socket 40-877 40-1306
40-915
P007 Air conditioner heat 40-689 40-1308
exchanger fan 40-695
P008 Auxiliary conditioner 40-689 40-1308
heat exchanger fan 40-695
P009 0.011.7543.3/30 Radio [LNK] 40-1318
P010 Clock [LNK] 40-1318
P011 0.011.7543.3/30 Radio [LNK] 40-1388
P012 Clock [LNK] 40-1388
P014 8A socket [LNK] 40-1331
P015 CAN socket [LNK] 40-1331
P019 2.7099.770.0 Cigarette lighter 40-1120 40-1365
P020 8A socket [LNK] 40-1365
P021 CAN socket 40-1262 40-1365
P022 25A socket [LNK] 40-1365
P023 Trailer socket, EU 40-902 40-1385
40-942
P024 Trailer socket, USA [LNK] 40-1385
P025 2.7099.770.0 Cigarette lighter [LNK] 40-1392
P026 CAN socket [LNK] 40-1392
P027 25A socket [LNK] 40-1392
P032 Wiring connector for [LNK] 40-1392
seat wiring loom
P034 2.7099.770.0 Cigarette lighter 40-1099 40-1331
USA version
Table 367
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P002 0.011.7543.3/30 Radio 40-1110 40-1301
40-1120

40-557
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P003 0.011.7543.3/30 Radio 40-1110 40-1301
40-1120
P004 0.011.5631.3 LH loudspeaker 40-1110 40-1301
40-1120
P005 0.011.5631.3 RH loudspeaker 40-1110 40-1301
40-1120
P006 Trailer socket 40-882 40-1306
40-928
P007 Air conditioner heat 40-689 40-1308
exchanger fan 40-695
P008 Auxiliary conditioner 40-689 40-1308
heat exchanger fan 40-695
P009 0.011.7543.3/30 Radio [LNK] 40-1318
P010 Clock [LNK] 40-1318
P011 0.011.7543.3/30 Radio [LNK] 40-1388
P012 Clock [LNK] 40-1388
P016 8A socket 40-1247 40-1347
P017 CAN socket [LNK] 40-1347
P018 25A socket 40-1247 40-1347
P019 2.7099.770.0 Cigarette lighter 40-1120 40-1365
P020 8A socket [LNK] 40-1365
P021 CAN socket 40-1262 40-1365
P022 25A socket [LNK] 40-1365
P023 Trailer socket, EU 40-902 40-1385
40-942
P024 Trailer socket, USA [LNK] 40-1385
P028 2.7099.770.0 Cigarette lighter [LNK] 40-1410
P029 CAN socket [LNK] 40-1410
P030 25A socket [LNK] 40-1410
P031 Wiring connector for 40-1110 40-1347
seat wiring loom
P033 Wiring connector for [LNK] 40-1410
seat wiring loom
P035 2.7099.770.0 Cigarette lighter 40-1110 40-1347

40-558
Wiring diagrams
40.2.84 - P - Various services (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM
420 -> ZKDW510200TD30001)
ITA version
Table 368
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P001 Auxiliary CANBUS 40-1250 40-1293
socket 40-1258
P002 0.011.7543.3/30 Radio 40-1105 40-1301
P003 0.011.7543.3/30 Radio 40-1105 40-1301
P004 0.011.5631.3 LH loudspeaker 40-1105 40-1301
P005 0.011.5631.3 RH loudspeaker 40-1105 40-1301
P006 Trailer socket 40-816 40-1306
40-877
40-889
40-922
40-959
P007 Air conditioner heat 40-665 40-1308
exchanger fan 40-671
P008 Auxiliary conditioner 40-665 40-1308
heat exchanger fan 40-671
P011 0.011.7543.3/30 Radio [LNK] 40-1388
P012 Clock [LNK] 40-1388
P014 8A socket [LNK] 40-1331
P015 CAN socket 40-1250 40-1331
P025 2.7099.770.0 Cigarette lighter 40-1133 40-1392
P026 CAN socket 40-1258 40-1392
P027 25A socket [LNK] 40-1392
P032 Wiring connector for 40-1133 40-1392
seat wiring loom
P034 2.7099.770.0 Cigarette lighter 40-1105 40-1331
USA version
Table 369
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P001 Auxiliary CANBUS 40-1250 40-1293
socket 40-1258
P002 0.011.7543.3/30 Radio 40-1115 40-1301
P003 0.011.7543.3/30 Radio 40-1115 40-1301
P004 0.011.5631.3 LH loudspeaker 40-1115 40-1301
P005 0.011.5631.3 RH loudspeaker 40-1115 40-1301
P006 Trailer socket 40-852 40-1306
40-882
40-895
40-935
P007 Air conditioner heat 40-683 40-1308
exchanger fan 40-677
P008 Auxiliary conditioner 40-683 40-1308
heat exchanger fan 40-677
P011 0.011.7543.3/30 Radio [LNK] 40-1388
P012 Clock [LNK] 40-1388
P016 8A socket [LNK] 40-1347
P017 CAN socket 40-1250 40-1347
P018 25A socket [LNK] 40-1347
P028 2.7099.770.0 Cigarette lighter 40-1141 40-1410
P029 CAN socket 40-1258 40-1410
P030 25A socket [LNK] 40-1410
P031 Wiring connector for 40-1115 40-1347
seat wiring loom

40-559
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P033 Wiring connector for 40-1141 40-1410
seat wiring loom
P035 2.7099.770.0 Cigarette lighter 40-1115 40-1347

40.2.85 - P - Various services (AGROFARM 430 -> ZKDW550200TD30001)

ITA version
Table 370
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P001 Auxiliary CANBUS 40-1250 40-1293
socket 40-1266
P002 0.011.7543.3/30 Radio 40-1105 40-1301
40-1125
P003 0.011.7543.3/30 Radio 40-1105 40-1301
40-1125
P004 0.011.5631.3 LH loudspeaker 40-1105 40-1301
40-1125
P005 0.011.5631.3 RH loudspeaker 40-1105 40-1301
40-1125
P006 Trailer socket 40-877 40-1306
40-922
P007 Air conditioner heat 40-689 40-1308
exchanger fan 40-695
P008 Auxiliary conditioner 40-689 40-1308
heat exchanger fan 40-695
P009 0.011.7543.3/30 Radio [LNK] 40-1318
P010 Clock [LNK] 40-1318
P011 0.011.7543.3/30 Radio [LNK] 40-1388
P012 Clock [LNK] 40-1388
P013 Air sprung seat [LNK] 40-1279
P014 8A socket [LNK] 40-1331
P015 CAN socket [LNK] 40-1331
P019 2.7099.770.0 Cigarette lighter 40-1125 40-1365
P020 8A socket [LNK] 40-1365
P021 CAN socket 40-1266 40-1365
P022 25A socket [LNK] 40-1365
P023 Trailer socket, EU 40-902 40-1385
40-948
P024 Trailer socket, USA [LNK] 40-1385
P025 2.7099.770.0 Cigarette lighter [LNK] 40-1392
P026 CAN socket [LNK] 40-1392
P027 25A socket [LNK] 40-1392
P032 Wiring connector for [LNK] 40-1392
seat wiring loom
P034 2.7099.770.0 Cigarette lighter 40-1105 40-1331
USA version
Table 371
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P001 Auxiliary CANBUS 40-1250 40-1293
socket 40-1266
P002 0.011.7543.3/30 Radio 40-1115 40-1301
40-1125
P003 0.011.7543.3/30 Radio 40-1115 40-1301
40-1125
P004 0.011.5631.3 LH loudspeaker 40-1115 40-1301
40-1125

40-560
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
P005 0.011.5631.3 RH loudspeaker 40-1115 40-1301
40-1125
P006 Trailer socket 40-882 40-1306
40-935
P007 Air conditioner heat 40-689 40-1308
exchanger fan 40-695
P008 Auxiliary conditioner 40-689 40-1308
heat exchanger fan 40-695
P009 0.011.7543.3/30 Radio [LNK] 40-1318
P010 Clock [LNK] 40-1318
P011 0.011.7543.3/30 Radio [LNK] 40-1388
P012 Clock [LNK] 40-1388
P013 Air sprung seat [LNK] 40-1279
P016 8A socket 40-1250 40-1347
P017 CAN socket [LNK] 40-1347
P018 25A socket 40-1250 40-1347
P019 2.7099.770.0 Cigarette lighter 40-1125 40-1365
P020 8A socket [LNK] 40-1365
P021 CAN socket 40-1266 40-1365
P022 25A socket [LNK] 40-1365
P023 Trailer socket, EU 40-902 40-1385
40-948
P024 Trailer socket, USA [LNK] 40-1385
P028 2.7099.770.0 Cigarette lighter [LNK] 40-1410
P029 CAN socket [LNK] 40-1410
P030 25A socket [LNK] 40-1410
P031 Wiring connector for 40-1115 40-1347
seat wiring loom
P033 Wiring connector for [LNK] 40-1410
seat wiring loom
P035 2.7099.770.0 Cigarette lighter 40-1115 40-1347

40-561
 Wiring diagrams
40.2.86 - Q - Safety devices (AGROFARM 410 -> ZKDW350200TD25001)
ITA version
Table 372
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-596 40-1330
switch 40-621
40-637
40-641
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-758
40-791
40-807
40-877
40-889
40-915
40-942
40-976
40-1024
40-1076
40-1099
40-1130
40-1145
40-1166
40-1247
40-1255
Q002 2.7659.351.0 Battery master 40-596 40-1330
switch 40-621
40-637
40-641
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-758
40-791
40-807
40-877
40-889
40-915
40-942
40-976
40-1024
40-1076
40-1099
40-1130
40-1145
40-1166
40-1247
40-1255

40-562
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q003 2.7659.351.0 Battery master 40-596 40-1330
switch 40-621
40-637
40-641
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-758
40-791
40-807
40-877
40-889
40-915
40-942
40-976
40-1024
40-1076
40-1099
40-1130
40-1145
40-1166
40-1247
40-1255
Q004 2.7659.351.0 Battery master 40-596 40-1330
switch 40-621
40-637
40-641
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-758
40-791
40-807
40-877
40-889
40-915
40-942
40-976
40-1024
40-1076
40-1099
40-1130
40-1145
40-1166
40-1247
40-1255

40-563
 Wiring diagrams
USA version
Table 373
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-604 40-1330
switch 40-629
40-647
40-652
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-772
40-826
40-843
40-882
40-895
40-928
40-953
40-992
40-1042
40-1087
40-1110
40-1137
40-1186
40-1206
40-1247
40-1255
Q002 2.7659.351.0 Battery master 40-604 40-1330
switch 40-629
40-647
40-652
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-772
40-826
40-843
40-882
40-895
40-928
40-953
40-992
40-1042
40-1087
40-1110
40-1137
40-1186
40-1206
40-1247
40-1255

40-564
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q003 2.7659.351.0 Battery master 40-604 40-1330
switch 40-629
40-647
40-652
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-772
40-826
40-843
40-882
40-895
40-928
40-953
40-992
40-1042
40-1087
40-1110
40-1137
40-1186
40-1206
40-1247
40-1255
Q004 2.7659.351.0 Battery master 40-604 40-1330
switch 40-629
40-647
40-652
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-772
40-826
40-843
40-882
40-895
40-928
40-953
40-992
40-1042
40-1087
40-1110
40-1137
40-1186
40-1206
40-1247
40-1255

40-565
 Wiring diagrams
40.2.87 - Q - Safety devices (AGROFARM 420 -> ZKDW390200TD25001)
ITA version
Table 374
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-596 40-1330
switch 40-621
40-637
40-641
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-758
40-791
40-807
40-877
40-889
40-915
40-942
40-976
40-1024
40-1076
40-1099
40-1130
40-1145
40-1166
40-1237
40-1247
40-1255

40-566
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q002 2.7659.351.0 Battery master 40-596 40-1330
switch 40-621
40-637
40-641
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-758
40-791
40-807
40-877
40-889
40-915
40-942
40-976
40-1024
40-1076
40-1099
40-1130
40-1145
40-1166
40-1237
40-1247
40-1255
Q003 2.7659.351.0 Battery master 40-596 40-1330
switch 40-621
40-637
40-641
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-758
40-791
40-807
40-877
40-889
40-915
40-942
40-976
40-1024
40-1076
40-1099
40-1130
40-1145
40-1166
40-1237
40-1247
40-1255

40-567
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q004 2.7659.351.0 Battery master 40-596 40-1330
switch 40-621
40-637
40-641
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-758
40-791
40-807
40-877
40-889
40-915
40-942
40-976
40-1024
40-1076
40-1099
40-1130
40-1145
40-1166
40-1237
40-1247
40-1255

40-568
Wiring diagrams
USA version
Table 375
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-604 40-1330
switch 40-629
40-647
40-652
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-772
40-826
40-843
40-882
40-895
40-928
40-953
40-992
40-1042
40-1087
40-1110
40-1137
40-1186
40-1206
40-1240
40-1247
40-1255
Q002 2.7659.351.0 Battery master 40-604 40-1330
switch 40-629
40-647
40-652
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-772
40-826
40-843
40-882
40-895
40-928
40-953
40-992
40-1042
40-1087
40-1110
40-1137
40-1186
40-1206
40-1240
40-1247
40-1255

40-569
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q003 2.7659.351.0 Battery master 40-604 40-1330
switch 40-629
40-647
40-652
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-772
40-826
40-843
40-882
40-895
40-928
40-953
40-992
40-1042
40-1087
40-1110
40-1137
40-1186
40-1206
40-1240
40-1247
40-1255
Q004 2.7659.351.0 Battery master 40-604 40-1330
switch 40-629
40-647
40-652
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-772
40-826
40-843
40-882
40-895
40-928
40-953
40-992
40-1042
40-1087
40-1110
40-1137
40-1186
40-1206
40-1240
40-1247
40-1255

40-570
Wiring diagrams
40.2.88 - Q - Safety devices (AGROFARM 430 -> ZKDW430200TD25001)
ITA version
Table 376
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-596 40-1330
switch 40-621
40-613
40-637
40-641
40-657
40-660
40-714
40-738
40-807
40-889
40-942
40-1076
40-1130
40-1166
40-1255
40-665
40-671
40-689
40-695
40-701
40-710
40-723
40-734
40-750
40-755
40-758
40-778
40-783
40-787
40-791
40-862
40-877
40-902
40-915
40-964
40-976
40-1008
40-1024
40-1008
40-1059
40-1099
40-1120
40-1145
40-1226
40-1237
40-1243
40-1243
40-1262
40-1269

40-571
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q002 2.7659.351.0 Battery master 40-596 40-1330
switch 40-613
40-637
40-641
40-657
40-660
40-714
40-738
40-807
40-889
40-942
40-1076
40-1130
40-1166
40-1255
40-621
40-665
40-671
40-689
40-695
40-701
40-710
40-723
40-734
40-750
40-755
40-758
40-778
40-783
40-787
40-791
40-862
40-877
40-902
40-915
40-964
40-976
40-1008
40-1024
40-1059
40-1099
40-1120
40-1145
40-1226
40-1237
40-1243
40-1262
40-1269

40-572
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q003 2.7659.351.0 Battery master 40-596 40-1330
switch 40-613
40-637
40-641
40-657
40-660
40-621
40-665
40-714
40-738
40-807
40-889
40-942
40-1076
40-1130
40-1166
40-1255
40-671
40-689
40-695
40-701
40-710
40-723
40-734
40-750
40-755
40-758
40-778
40-783
40-787
40-791
40-862
40-877
40-902
40-915
40-964
40-976
40-1008
40-1024
40-1059
40-1099
40-1120
40-1145
40-1226
40-1237
40-1243
40-1262
40-1269

40-573
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q004 2.7659.351.0 Battery master 40-596 40-1330
switch 40-613
40-637
40-641
40-657
40-660
40-621
40-714
40-738
40-807
40-889
40-942
40-1076
40-1130
40-1166
40-1255
40-665
40-671
40-689
40-695
40-701
40-710
40-723
40-734
40-750
40-755
40-758
40-778
40-783
40-787
40-791
40-862
40-877
40-902
40-915
40-964
40-976
40-1008
40-1024
40-1059
40-1099
40-1120
40-1145
40-1226
40-1237
40-1243
40-1262
40-1269

40-574
Wiring diagrams
USA version
Table 377
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-604 40-1330
switch 40-613
40-647
40-652
40-657
40-660
40-683
40-629
40-719
40-743
40-843
40-895
40-953
40-1087
40-1137
40-1206
40-1255
40-677
40-689
40-695
40-705
40-710
40-728
40-734
40-764
40-769
40-772
40-778
40-783
40-787
40-826
40-862
40-882
40-902
40-928
40-964
40-992
40-1008
40-1042
40-1059
40-1110
40-1120
40-1186
40-1226
40-1240
40-1243
40-1262
40-1269

40-575
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q002 2.7659.351.0 Battery master 40-604 40-1330
switch 40-613
40-647
40-652
40-657
40-660
40-629
40-719
40-743
40-843
40-895
40-953
40-1087
40-1137
40-1206
40-1255
40-683
40-677
40-689
40-695
40-705
40-710
40-728
40-734
40-764
40-769
40-772
40-778
40-783
40-787
40-826
40-862
40-882
40-902
40-928
40-964
40-992
40-1008
40-1042
40-1059
40-1110
40-1120
40-1186
40-1226
40-1240
40-1243
40-1262
40-1269

40-576
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q003 2.7659.351.0 Battery master 40-604 40-1330
switch 40-613
40-647
40-652
40-657
40-660
40-629
40-719
40-743
40-843
40-895
40-953
40-1087
40-1137
40-1206
40-1255
40-683
40-677
40-689
40-695
40-705
40-710
40-728
40-734
40-764
40-769
40-772
40-778
40-783
40-787
40-826
40-862
40-882
40-902
40-928
40-964
40-992
40-1008
40-1042
40-1059
40-1110
40-1120
40-1186
40-1226
40-1240
40-1243
40-1262
40-1269

40-577
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q004 2.7659.351.0 Battery master 40-604 40-1330
switch 40-613
40-647
40-652
40-657
40-660
40-683
40-629
40-719
40-743
40-843
40-895
40-953
40-1087
40-1137
40-1206
40-1255
40-677
40-689
40-695
40-705
40-710
40-728
40-734
40-764
40-769
40-772
40-778
40-783
40-787
40-826
40-862
40-882
40-902
40-928
40-964
40-992
40-1008
40-1042
40-1059
40-1110
40-1120
40-1186
40-1226
40-1240
40-1243
40-1262
40-1269

40-578
Wiring diagrams
40.2.89 - Q - Safety devices (AGROFARM 410 -> ZKDW470200TD30001)
ITA version
Table 378
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-600 40-1330
switch 40-625
40-637
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-799
40-816
40-877
40-889
40-922
40-948
40-984
40-1033
40-1082
40-1105
40-1133
40-1151
40-1171
40-1237
40-1250
40-1258
Q002 2.7659.351.0 Battery master 40-600 40-1330
switch 40-625
40-637
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-799
40-816
40-877
40-889
40-922
40-948
40-984
40-1033
40-1082
40-1105
40-1133
40-1151
40-1171
40-1237
40-1250
40-1258

40-579
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q003 2.7659.351.0 Battery master 40-600 40-1330
switch 40-625
40-637
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-799
40-816
40-877
40-889
40-922
40-948
40-984
40-1033
40-1082
40-1105
40-1133
40-1151
40-1171
40-1237
40-1250
40-1258
Q004 2.7659.351.0 Battery master 40-600 40-1330
switch 40-625
40-637
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-799
40-816
40-877
40-889
40-922
40-948
40-984
40-1033
40-1082
40-1105
40-1133
40-1151
40-1171
40-1237
40-1250
40-1258

40-580
Wiring diagrams
USA version
Table 379
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-608 40-1330
switch 40-633
40-647
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-834
40-852
40-882
40-895
40-935
40-959
40-1001
40-1050
40-1093
40-1115
40-1141
40-1192
40-1211
40-1240
40-1250
40-1258
Q002 2.7659.351.0 Battery master 40-608 40-1330
switch 40-633
40-647
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-834
40-852
40-882
40-895
40-935
40-959
40-1001
40-1050
40-1093
40-1115
40-1141
40-1192
40-1211
40-1240
40-1250
40-1258

40-581
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q003 2.7659.351.0 Battery master 40-608 40-1330
switch 40-633
40-647
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-834
40-852
40-882
40-895
40-935
40-959
40-1001
40-1050
40-1093
40-1115
40-1141
40-1192
40-1211
40-1240
40-1250
40-1258
Q004 2.7659.351.0 Battery master 40-608 40-1330
switch 40-633
40-647
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-834
40-852
40-882
40-895
40-935
40-959
40-1001
40-1050
40-1093
40-1115
40-1141
40-1192
40-1211
40-1240
40-1250
40-1258

40-582
Wiring diagrams
40.2.90 - Q - Safety devices (AGROFARM 420 -> ZKDW510200TD30001)
ITA version
Table 380
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-600 40-1330
switch 40-625
40-637
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-799
40-816
40-877
40-889
40-922
40-948
40-984
40-1033
40-1082
40-1105
40-1133
40-1158
40-1178
40-1237
40-1250
40-1258
Q002 2.7659.351.0 Battery master 40-600 40-1330
switch 40-625
40-637
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-799
40-816
40-877
40-889
40-922
40-948
40-984
40-1033
40-1082
40-1105
40-1133
40-1158
40-1178
40-1237
40-1250
40-1258

40-583
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q003 2.7659.351.0 Battery master 40-600 40-1330
switch 40-625
40-637
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-799
40-816
40-877
40-889
40-922
40-948
40-984
40-1033
40-1082
40-1105
40-1133
40-1158
40-1178
40-1237
40-1250
40-1258
Q004 2.7659.351.0 Battery master 40-600 40-1330
switch 40-625
40-637
40-665
40-671
40-701
40-714
40-723
40-738
40-750
40-755
40-799
40-816
40-877
40-889
40-922
40-948
40-984
40-1033
40-1082
40-1105
40-1133
40-1158
40-1178
40-1237
40-1250
40-1258

40-584
Wiring diagrams
USA version
Table 381
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-608 40-1330
switch 40-633
40-647
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-834
40-852
40-882
40-895
40-935
40-959
40-1001
40-1050
40-1093
40-1115
40-1141
40-1199
40-1218
40-1240
40-1250
40-1258
Q002 2.7659.351.0 Battery master 40-608 40-1330
switch 40-633
40-647
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-834
40-852
40-882
40-895
40-935
40-959
40-1001
40-1050
40-1093
40-1115
40-1141
40-1199
40-1218
40-1240
40-1250
40-1258

40-585
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q003 2.7659.351.0 Battery master 40-608 40-1330
switch 40-633
40-647
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-834
40-852
40-882
40-895
40-935
40-959
40-1001
40-1050
40-1093
40-1115
40-1141
40-1199
40-1218
40-1240
40-1250
40-1258
Q004 2.7659.351.0 Battery master 40-608 40-1330
switch 40-633
40-647
40-683
40-677
40-705
40-719
40-728
40-743
40-764
40-769
40-834
40-852
40-882
40-895
40-935
40-959
40-1001
40-1050
40-1093
40-1115
40-1141
40-1199
40-1218
40-1240
40-1250
40-1258

40-586
Wiring diagrams
40.2.91 - Q - Safety devices (AGROFARM 430 -> ZKDW550200TD30001)
ITA version
Table 382
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-596 40-1330
switch 40-616
40-637
40-657
40-665
40-671
40-689
40-695
40-701
40-710
40-723
40-734
40-750
40-755
40-778
40-783
40-791
40-870
40-877
40-902
40-915
40-970
40-976
40-1016
40-1024
40-1016
40-1067
40-1099
40-1125
40-1145
40-1158
40-1231
40-1237
40-1243
40-1243
40-1269
40-1266

40-587
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q002 2.7659.351.0 Battery master 40-596 40-1330
switch 40-616
40-637
40-657
40-665
40-671
40-689
40-695
40-701
40-710
40-723
40-734
40-750
40-755
40-778
40-783
40-791
40-870
40-877
40-902
40-915
40-970
40-976
40-1016
40-1024
40-1067
40-1099
40-1125
40-1145
40-1158
40-1231
40-1237
40-1243
40-1269
40-1266

40-588
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q003 2.7659.351.0 Battery master 40-596 40-1330
switch 40-616
40-637
40-657
40-665
40-671
40-689
40-695
40-701
40-710
40-723
40-734
40-750
40-755
40-778
40-783
40-791
40-870
40-877
40-902
40-915
40-970
40-976
40-1016
40-1024
40-1067
40-1099
40-1125
40-1145
40-1158
40-1231
40-1237
40-1243
40-1269
40-1266

40-589
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q004 2.7659.351.0 Battery master 40-596 40-1330
switch 40-616
40-637
40-657
40-665
40-671
40-689
40-695
40-701
40-710
40-723
40-734
40-750
40-755
40-778
40-783
40-791
40-870
40-877
40-902
40-915
40-970
40-976
40-1016
40-1024
40-1067
40-1099
40-1125
40-1145
40-1158
40-1231
40-1237
40-1243
40-1269
40-1266

40-590
Wiring diagrams
USA version
Table 383
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q001 2.7659.351.0 Battery master 40-604 40-1330
switch 40-616
40-647
40-657
40-683
40-677
40-689
40-695
40-705
40-710
40-728
40-734
40-764
40-769
40-778
40-783
40-826
40-870
40-882
40-902
40-928
40-970
40-992
40-1016
40-1042
40-1067
40-1110
40-1125
40-1186
40-1199
40-1231
40-1240
40-1243
40-1269
40-1266

40-591
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q002 2.7659.351.0 Battery master 40-604 40-1330
switch 40-616
40-647
40-657
40-683
40-677
40-689
40-695
40-705
40-710
40-728
40-734
40-764
40-769
40-778
40-783
40-826
40-870
40-882
40-902
40-928
40-970
40-992
40-1016
40-1042
40-1067
40-1110
40-1125
40-1186
40-1199
40-1231
40-1240
40-1243
40-1269
40-1266

40-592
Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q003 2.7659.351.0 Battery master 40-604 40-1330
switch 40-616
40-647
40-657
40-683
40-677
40-689
40-695
40-705
40-710
40-728
40-734
40-764
40-769
40-778
40-783
40-826
40-870
40-882
40-902
40-928
40-970
40-992
40-1016
40-1042
40-1067
40-1110
40-1125
40-1186
40-1199
40-1231
40-1240
40-1243
40-1269
40-1266

40-593
 Wiring diagrams
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
Q004 2.7659.351.0 Battery master 40-604 40-1330
switch 40-616
40-647
40-657
40-683
40-677
40-689
40-695
40-705
40-710
40-728
40-734
40-764
40-769
40-778
40-783
40-826
40-870
40-882
40-902
40-928
40-970
40-992
40-1016
40-1042
40-1067
40-1110
40-1125
40-1186
40-1199
40-1231
40-1240
40-1243
40-1269
40-1266

40-594
Wiring diagrams
40.2.92 - R - Diagnostics (AGROFARM 410 -> ZKDW350200TD25001, AGROFARM 420 ->
ZKDW390200TD25001)
Table 384
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
R001 Diagnostics socket 40-791 40-1331
R002 Diagnostics socket 40-826 40-1347
R004 Diagnostics socket 40-807 40-1392
R005 Diagnostics socket 40-843 40-1410
R006 Diagnostics socket 40-1410

40.2.93 - R - Diagnostics (AGROFARM 430 -> ZKDW430200TD25001)

Table 385
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
R001 Diagnostics socket 40-791 40-1331
R002 Diagnostics socket 40-826 40-1347
R003 Diagnostics socket 40-862 40-1365
R004 Diagnostics socket 40-807 40-1392
R005 Diagnostics socket 40-843 40-1410
R006 Diagnostics socket 40-1410

40.2.94 - R - Diagnostics (AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 ->

ZKDW510200TD30001)
Table 386
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
R001 Diagnostics socket 40-799 40-1331
R002 Diagnostics socket 40-834 40-1347
R004 Diagnostics socket 40-816 40-1392
R005 Diagnostics socket 40-852 40-1410
R006 Diagnostics socket 40-1410

40.2.95 - R - Diagnostics (AGROFARM 430 -> ZKDW550200TD30001)

Table 387
System code P/N Description CHARACTERISTICS/ Link to system Link to wiring
NOTES loom
R001 Diagnostics socket 40-799 40-1331
R002 Diagnostics socket 40-834 40-1347
R003 Diagnostics socket 40-870 40-1365

40-595
 Wiring diagrams
40.3 - Systems
40.3.1 - S001 - Cab engine start - ITA (AGROFARM 410 -> ZKDW350200TD25001, AGRO-
FARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)

M002
M003

I035 Ja007 I027

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C007 C009

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.3567.4/60

Ba018 Ba024
Ba017
7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1

3 9 2

C008
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1

B001
D006
60A

0.016.2001.4/10*
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

J003
J004*
J006a
J006b

I007
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1116
l A001 - +30 Battery
l A002 - Preheating device
l A006 - Starter motor “+50”
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A018 - Starter motor “+50”
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Ba017 - Instrument panel fuse (key-on power) (10A)
l Ba018 - Engine ECU fuse (key-on power) (7.5A)
l Ba024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C007 - Earthing point
l C008 - Earthing point
l C009 - Earthing point
l D004 - Wiring connector for central wiring loom
l D004 - Wiring connector for rear wiring loom
l D006 - Wiring connector for reverse shuttle wiring loom
l D010 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D040 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l I007 - Start enable switch (transmission in neutral)
l I027 - Clutch engage-disengage control
l I035 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay
l Ja007 - Starter relay

40-596
Wiring diagrams

M002
M003

I035 Ja007 I027

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C007 C009

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.3567.4/60

Ba018 Ba024
Ba017
7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1

3 9 2

C008
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1

B001
D006
60A

0.016.2001.4/10*
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

J003
J004*
J006a
J006b

I007
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1116
l M002 - Engine ECU
l M003 - Engine ECU
l N005 - Starter motor “+30”
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 388
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A006 Starter motor “+50” 40-1324
A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A018 Starter motor “+50” 40-1327
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Ba017 Instrument panel 40-1331
fuse (key-on power)
(10A)
Ba018 Engine ECU fuse 40-1331
(key-on power)
(7.5A)
Ba024 Starter fuse (40A) 40-1331
C004 Earthing point 40-1330

40-597
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
C005 Earthing point 40-1330
C007 Earthing point 40-1331
C008 Earthing point 40-1331
C009 Earthing point 40-1331
D004 Wiring connector for 40-1331
rear wiring loom
D004 Wiring connector for 40-1331
central wiring loom
D006 Wiring connector for 40-1331
reverse shuttle wir- D006

ing loom
F0130180

D010 Wiring connector for 40-1324

engine wiring loom
D010 Wiring connector for 40-1331
engine wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1295
central wiring loom
I007 2.7659.343.0/10 Start enable switch 40-1306
(transmission in neu-
tral)
3,9 Ohm

I027 2.7659.097.0 Clutch engage-dis- 1 40-1331

engage control
4

Between Pin 1 and

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I035 0.015.0485.4 Starter switch 40-1331
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

J003 Preheating relay 40-1324

J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

40-598
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
J006b Starter relay J006b
40-1290

Ja007 Central cab wiring 40-1331

loom
M002 Central cab wiring 40-1331
loom
M003 Engine control unit 40-1331

Table 389
System Code P/N Description Characteristics/ Position Wiring loom
notes
N005 Starter motor “+30” 40-1329
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-599
 Wiring diagrams
40.3.2 - S001 - Cab engine start - ITA (AGROFARM 410 -> ZKDW470200TD30001, AGRO-
FARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)

M002
M003

I035 Ja007 I027

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C007 C009

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.3567.4/60

Ba018 Ba024
Ba017
7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006 3 9 2

C008
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1 3 9 2

B001
60A

0.016.2001.4/10*

0.015.1418.4/30
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2 8 9 18 15

-31
-31

+15
DIG.CLUTCH
H004
J006a
J006b

J003
J004*

I007
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1117
l A001 - +30 Battery
l A002 - Preheating device
l A006 - Starter motor “+50”
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A018 - Starter motor “+50”
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Ba017 - Instrument panel fuse (key-on power) (10A)
l Ba018 - Engine ECU fuse (key-on power) (7.5A)
l Ba024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C007 - Earthing point
l C008 - Earthing point
l C009 - Earthing point
l D004 - Wiring connector for central wiring loom
l D004 - Wiring connector for rear wiring loom
l D006 - Wiring connector for central wiring loom
l D006 - Wiring connector for reverse shuttle wiring loom
l D010 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D040 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l H004 - Shuttle lever
l I007 - Start enable switch (transmission in neutral)
l I027 - Clutch engage-disengage control
l I035 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay

40-600
Wiring diagrams

M002
M003

I035 Ja007 I027

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C007 C009

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.3567.4/60

Ba018 Ba024
Ba017
7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006 3 9 2

C008
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1 3 9 2

B001
60A

0.016.2001.4/10*

0.015.1418.4/30
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2 8 9 18 15

-31
-31

+15
DIG.CLUTCH
H004
J006a
J006b

J003
J004*

I007
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1117
l Ja007 - Starter relay
l M002 - Engine ECU
l M003 - Engine ECU
l N005 - Starter motor “+30”
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 390
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A006 Starter motor “+50” 40-1324
A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A018 Starter motor “+50” 40-1327
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Ba017 Instrument panel 40-1331
fuse (key-on power)
(10A)
Ba018 Engine ECU fuse 40-1331
(key-on power)
(7.5A)
Ba024 Starter fuse (40A) 40-1331

40-601
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C007 Earthing point 40-1331
C008 Earthing point 40-1331
C009 Earthing point 40-1331
D004 Wiring connector for 40-1331
rear wiring loom
D004 Wiring connector for 40-1306
central wiring loom
D006 Wiring connector for 40-1331
reverse shuttle wir- D006

ing loom
F0130180

D006 Wiring connector for 40-1293

central wiring loom D006

F0130180

D010 Wiring connector for 40-1331

engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D040 Wiring connector for 40-1331
power wiring loom
D040 Wiring connector for 40-1295
central wiring loom
H004 Shuttle lever 40-1293
H004

Fig. 1118
I007 2.7659.343.0/10 Start enable switch 40-1306
(transmission in neu-
tral)
3,9 Ohm

I027 2.7659.097.0 Clutch engage-dis- 1 40-1331

engage control
4

Between Pin 1 and

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch

40-602
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
I035 0.015.0485.4 Starter switch 40-1331
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

J003 Preheating relay 40-1324

J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

Fig. 1119
J006b Starter relay J006b
40-1290

Fig. 1120
Ja007 Central cab wiring 40-1331
loom
Table 391
System Code P/N Description Characteristics/ Position Wiring loom
notes
M002 Central cab wiring 40-1331
loom
M003 Engine control unit 40-1331
N005 Starter motor “+30” 40-1329
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

40-603
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q003 2.7659.351.0 Battery master 40-1330
switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40.3.3 - S001 - Cab engine start - USA (AGROFARM 410 -> ZKDW350200TD25001, AGRO-
FARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
M007

M008

I045 Jb007 I043

START CONSENT
H.D.COMAND

30
-31 ELECTR.

-31 ELECTR.

50 15
C010 C012
+15

50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.4081.4/30

Bb017 Bb018 Bb024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006

3 9 2

C011
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1

B001
60A

0.016.2001.4/10*
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

J006a
J006b

J003
J004*

I007
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1121
l A001 - +30 Battery
l A002 - Preheating device
l A006 - Starter motor “+50”
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A018 - Starter motor “+50”
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bb017 - Instrument panel fuse (key-on power) (10A)

40-604
Wiring diagrams

M007
M008

I045 Jb007 I043

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C010 C012

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.4081.4/30

Bb017 Bb018 Bb024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006

3 9 2

C011
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1

B001
60A

0.016.2001.4/10*
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

J006a
J006b

J003
J004*

I007
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1121
l Bb018 - Engine ECU fuse (key-on power) (7.5A)
l Bb024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C010 - Earthing point
l C011 - Earthing point
l C012 - Earthing point
l D004 - Wiring connector for central wiring loom
l D004 - Wiring connector for rear wiring loom
l D006 - Wiring connector for reverse shuttle wiring loom
l D010 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D040 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l I007 - Start enable switch (transmission in neutral)
l I043 - Clutch engage-disengage control
l I045 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay
l Jb007 - Starter relay
l M007 - Engine ECU
l M008 - Engine ECU
l N005 - Starter motor “+30”
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

40-605
 Wiring diagrams
Table 392
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A006 Starter motor “+50” 40-1324
A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A018 Starter motor “+50” 40-1327
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Bb017 Instrument panel 40-1347
fuse (key-on power)
(10A)
Bb018 Engine ECU fuse 40-1347
(key-on power)
(7.5A)
Bb024 Starter fuse (40A) 40-1347
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C010 Grounding point 40-1347
C011 Grounding point 40-1347
C012 Earthing point 40-1347
D004 Wiring connector for 40-1331
rear wiring loom
D004 Wiring connector for 40-1331
central wiring loom
D006 Wiring connector for 40-1331
reverse shuttle wir- D006

ing loom
F0130180

D010 Wiring connector for 40-1324

engine wiring loom
D010 Wiring connector for 40-1331
engine wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1295
central wiring loom
I007 2.7659.343.0/10 Start enable switch 40-1306
(transmission in neu-
tral)
3,9 Ohm

40-606
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
I043 2.7659.097.0 Clutch engage-dis- 1 40-1347
engage control
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I045 0.015.0485.4 Starter switch 40-1347
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

J003 Preheating relay 40-1324

J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

J006b Starter relay J006b

40-1290

Jb007 Central cab wiring 40-1347

loom
M007 Central cab wiring 40-1347
loom
M008 Engine control unit 40-1347

40-607
 Wiring diagrams
Table 393
System Code P/N Description Characteristics/ Position Wiring loom
notes
N005 Starter motor “+30” 40-1329
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-608
Wiring diagrams
40.3.4 - S001 - Cab engine start - USA (AGROFARM 410 -> ZKDW470200TD30001, AGRO-
FARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW550200TD30001)

M007
M008

I045 Jb007 I043

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C010 C012

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.4081.4/30

Bb017 Bb018 Bb024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006 3 9 2

C011
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1 3 9 2

B001
60A

0.016.2001.4/10*

0.015.1418.4/30
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2 8 9 18 15

-31
-31

+15
DIG.CLUTCH
J006a
J006b

J003
J004*

I007 H004
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1122
l A001 - +30 Battery
l A002 - Preheating device
l A006 - Starter motor “+50”
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A018 - Starter motor “+50”
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bb017 - Instrument panel fuse (key-on power) (10A)
l Bb018 - Engine ECU fuse (key-on power) (7.5A)
l Bb024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C010 - Earthing point
l C011 - Earthing point
l C012 - Earthing point
l D004 - Wiring connector for central wiring loom
l D004 - Wiring connector for rear wiring loom
l D006 - Wiring connector for reverse shuttle wiring loom
l D006 - Wiring connector for central wiring loom
l D010 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D040 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l H004 - Shuttle lever
l I007 - Start enable switch (transmission in neutral)
l I043 - Clutch engage-disengage control
l I045 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay

40-609
 Wiring diagrams

M007
M008

I045 Jb007 I043

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C010 C012

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.4081.4/30

Bb017 Bb018 Bb024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006 3 9 2

C011
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1 3 9 2

B001
60A

0.016.2001.4/10*

0.015.1418.4/30
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2 8 9 18 15

-31
-31

+15
DIG.CLUTCH
J006a
J006b

J003
J004*

I007 H004
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1122
l Jb007 - Starter relay
l M007 - Engine ECU
l M008 - Engine ECU
l N005 - Starter motor “+30”
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 394
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

Fig. 1123
A002 04258670 Preheating device 40-1290
A006 Starter motor “+50” 40-1324
A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A018 Starter motor “+50” 40-1327
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Bb017 Instrument panel 40-1347
fuse (key-on power)
(10A)
Bb018 Engine ECU fuse 40-1347
(key-on power)
(7.5A)

40-610
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Bb024 Starter fuse (40A) 40-1347
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C010 Grounding point 40-1347
C011 Grounding point 40-1347
C012 Earthing point 40-1347
D004 Wiring connector for 40-1331
rear wiring loom
D004 Wiring connector for 40-1331
central wiring loom
D006 Wiring connector for 40-1293
central wiring loom D006

F0130180

Fig. 1124
D006 Wiring connector for 40-1331
reverse shuttle wir- D006

ing loom
F0130180

Fig. 1124
D010 Wiring connector for 40-1324
central wiring loom
D010 Wiring connector for 40-1331
front wiring loom
D040 Wiring connector for 40-1295
power wiring loom
D040 Wiring connector for 40-1295
central wiring loom
H004 Shuttle lever 40-1293
H004

I007 2.7659.343.0/10 Start enable switch 40-1306

(transmission in neu-
tral)
3,9 Ohm

I043 2.7659.097.0 Clutch engage-dis- 1 40-1347

engage control
4

Between Pin 1 and

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I045 0.015.0485.4 Starter switch 40-1347
J003 Preheating relay 40-1324
J004 Preheating relay 40-1327

40-611
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
J006a Preheating relay J006a
40-1290

Fig. 1125
J006b Starter relay J006b
40-1290

Jb007 Central cab wiring 40-1347

loom

Table 395
System Code P/N Description Characteristics/ Position Wiring loom
notes
M007 Central cab wiring 40-1347
loom
M008 Engine control unit 40-1347
N005 Starter motor “+30” 40-1329
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-612
Wiring diagrams
40.3.5 - S001 - Engine start, cab with electronic lift (AGROFARM 430 -> ZKD-
W430200TD25001)

M009
M010

I061 Jc007 I057

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C013 C015

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.4537.4/40

Bc017 Bc018 Bc024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D022 B-A3

D006
3 9 2
0.015.1983.4/10

4 5 1 14 B-A3

B001
60A

0.016.2001.4/10*
0.016.2000.4/20
0.014.9195.4/20

0.018.4891.4
B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

C016
J006a
J006b

J003
J004*

I064
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1126
l A001 - +30 Battery
l A002 - Preheating device
l A006 - Starter motor “+50”
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A018 - Starter motor “+50”
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bc017 - Instrument panel fuse (key-on power) (10A)
l Bc018 - Engine ECU fuse (key-on power) (7.5A)
l Bc024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C013 - Earthing point
l C015 - Earthing point
l C016 - Earthing point
l D006 - Wiring connector for reverse shuttle wiring loom
l D010 - Wiring connector for central wiring loom
l D010 - Wiring connector for front wiring loom
l D022 - Wiring connector for rear wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l I057 - Clutch engage-disengage control
l I061 - Ignition switch
l I064 - Start enable switch (transmission in neutral)
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay
l Jc007 - Starter relay
l M009 - Engine ECU
l M010 - Engine ECU

40-613
 Wiring diagrams

M009
M010

I061 Jc007 I057

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C013 C015

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.4537.4/40

Bc017 Bc018 Bc024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D022 B-A3

D006
3 9 2
0.015.1983.4/10

4 5 1 14 B-A3

B001
60A

0.016.2001.4/10*
0.016.2000.4/20
0.014.9195.4/20

0.018.4891.4
B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

C016
J006a
J006b

J003
J004*

I064
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1126
l N005 - Starter motor “+30”
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 396
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A006 Starter motor “+50” 40-1324
A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A018 Starter motor “+50” 40-1327
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Bc017 Instrument panel 40-1365
fuse (key-on power)
(10A)
Bc018 Engine ECU fuse 40-1365
(key-on power)
(7.5A)
Bc024 Starter fuse (40A) 40-1365
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C013 Earthing point 40-1365

40-614
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
C014 Grounding point 40-1365
C015 Grounding point 40-1365
C016 Earthing point 40-1385
D006 Wiring connector for 40-1365
reverse shuttle wir- D006

ing loom
F0130180

Fig. 1127
D010 Wiring connector for 40-1324
central wiring loom
D010 Wiring connector for 40-1365
front wiring loom
D022 Wiring connector for 40-1365
rear wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1365
power wiring loom
I057 2.7659.097.0 Clutch engage-dis- 1 40-1365
engage control
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I061 0.015.0485.4 Starter switch 40-1365
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

I064 Start enable switch 40-1385

(transmission in neu-
tral)
J003 Preheating relay 40-1324
J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

J006b Starter relay J006b

40-1290

Fig. 1128
Jc007 Central cab wiring 40-1365
loom
M009 Engine control unit 40-1365
M010 Central cab wiring 40-1365
loom
N005 Starter motor “+30” 40-1329

40-615
 Wiring diagrams
Table 397
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-616
Wiring diagrams
40.3.6 - S001 - Engine start, cab with electronic lift (AGROFARM 430 -> ZKD-
W550200TD30001)

M009
M010

I061 Jc007 I057

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C013 C015

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.4537.4/40

Bc017 Bc018 Bc024

7,5 A

40 A
10A

D040 4 5 1 14 D035 D022 B-A3 D006 3 9 2

0.015.1983.4/10

4 5 1 14 B-A3 3 9 2

B001
60A

0.016.2001.4/10*

0.015.1418.4/30
0.016.2000.4/20
0.014.9195.4/20

0.018.4891.4
B002

C004
125A

A006
0.017.8922.4/10

A001 A002 4 3 1 2 A018* 1 2 8 9 18 15

C016

-31
-31

+15
DIG.CLUTCH
J006a
J006b

J003
J004*

I064 H004

Q002 Q001 A015 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1129
l A001 - +30 Battery
l A002 - Preheating device
l A006 - Starter motor “+50”
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A018 - Starter motor “+50”
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bc017 - Instrument panel fuse (key-on power) (10A)
l Bc018 - Engine ECU fuse (key-on power) (7.5A)
l Bc024 - Starter fuse (40A)
l C004 - Earthing point
l C004 - Earthing point
l C005 - Earthing point
l C015 - Earthing point
l C016 - Earthing point
l D006 - Wiring connector for central wiring loom
l D006 - Wiring connector for reverse shuttle wiring loom
l D010 - Wiring connector for central wiring loom
l D010 - Wiring connector for front wiring loom
l D022 - Wiring connector for rear wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l H004 - Shuttle lever
l I057 - Clutch engage-disengage control
l I061 - Ignition switch
l I064 - Start enable switch (transmission in neutral)
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay
l Jc007 - Starter relay
l M009 - Engine ECU

40-617
 Wiring diagrams

M009
M010

I061 Jc007 I057

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C013 C015

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.4537.4/40

Bc017 Bc018 Bc024

7,5 A

40 A
10A

D040 4 5 1 14 D035 D022 B-A3 D006 3 9 2

0.015.1983.4/10

4 5 1 14 B-A3 3 9 2

B001
60A

0.016.2001.4/10*

0.015.1418.4/30
0.016.2000.4/20
0.014.9195.4/20

0.018.4891.4
B002

C004
125A

A006
0.017.8922.4/10

A001 A002 4 3 1 2 A018* 1 2 8 9 18 15

C016

-31
-31

+15
DIG.CLUTCH
J006a
J006b

J003
J004*

I064 H004

Q002 Q001 A015 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1129
l M010 - Engine ECU
l N005 - Starter motor “+30”
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 398
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A006 Starter motor “+50” 40-1324
A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A018 Starter motor “+50” 40-1327
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Bc017 Instrument panel 40-1365
fuse (key-on power)
(10A)
Bc018 Engine ECU fuse 40-1365
(key-on power)
(7.5A)
Bc024 Starter fuse (40A) 40-1365
C004 Earthing point 40-1330

40-618
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
C005 Grounding point [LNK]
C013 Earthing point 40-1365
C015 Grounding point 40-1365
C016 Grounding point [LNK]
D006 Wiring connector for 40-1293
central wiring loom D006

F0130180

D006 Wiring connector for 40-1365

reverse shuttle wir- D006

ing loom
F0130180

Fig. 1130
D010 Wiring connector for 40-1324
central wiring loom
D010 Wiring connector for 40-1365
front wiring loom
D022 Wiring connector for [LNK]
rear wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1365
power wiring loom
H004 Shuttle lever 40-1293
H004

I057 2.7659.097.0 Clutch engage-dis- 1 40-1365

engage control
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I061 0.015.0485.4 Starter switch 40-1365
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

I064 Start enable switch [LNK]

(transmission in neu-
tral)
J003 Preheating relay 40-1324
J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

40-619
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
J006b Starter relay J006b
40-1290

Jc007 Central cab wiring 40-1365

loom
M009 Engine control unit 40-1365

Table 399
System Code P/N Description Characteristics/ Position Wiring loom
notes
M010 Central cab wiring 40-1365
loom
N005 Starter motor “+30” 40-1329
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-620
Wiring diagrams
40.3.7 - S001 - Cab engine start - ITA (AGROFARM 410 -> ZKDW350200TD25001, AGRO-
FARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)

M013
M014

I087 Jd007 I079

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C017 C019

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.7845.4/20

Bd017 Bd018 Bd024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1

D006
3 9 2

C018
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1

B001
60A

0.016.2001.4/10*
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

J006a
J006b

J003
J004*

I007
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1131
l A001 - +30 Battery
l A002 - Preheating device
l A006 - Starter motor “+50”
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A018 - Starter motor “+50”
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bd017 - Instrument panel fuse (key-on power) (10A)
l Bd018 - Engine ECU fuse (key-on power) (7.5A)
l Bd024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C017 - Earthing point
l C018 - Earthing point
l C019 - Earthing point
l D004 - Wiring connector for central wiring loom
l D004 - Wiring connector for rear wiring loom
l D006 - Wiring connector for reverse shuttle wiring loom
l D010 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l I007 - Start enable switch (transmission in neutral)
l I079 - Clutch engage-disengage control
l I087 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay
l Jd007 - Starter relay
l M013 - Engine ECU

40-621
 Wiring diagrams

M013
M014

I087 Jd007 I079

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C017 C019

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.7845.4/20

Bd017 Bd018 Bd024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1

D006
3 9 2

C018
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1

B001
60A

0.016.2001.4/10*
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

J006a
J006b

J003
J004*

I007
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1131
l M014 - Engine ECU
l N005 - Starter motor “+30”
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 400
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A006 Starter motor “+50” 40-1324
A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A018 Starter motor “+50” 40-1327
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Bd017 Instrument panel 40-1392
fuse (key-on power)
(10A)
Bd018 Engine ECU fuse 40-1392
(key-on power)
(7.5A)
Bd024 Starter fuse (40A) 40-1392
C004 Earthing point 40-1330
C005 Earthing point 40-1330

40-622
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
C017 Earthing point 40-1392
C018 Earthing point 40-1392
C019 Grounding point 40-1392
D004 Wiring connector for 40-1306
central wiring loom
D004 Wiring connector for 40-1392
central wiring loom
D006 Wiring connector for 40-1392
reverse shuttle wir- D006

ing loom
F0130180

D010 Wiring connector for 40-1324

central wiring loom
D010 Wiring connector for 40-1392
engine wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1392
power wiring loom
I007 2.7659.343.0/10 Start enable switch 40-1306
(transmission in neu-
tral)
3,9 Ohm

I079 2.7659.097.0 Clutch engage-dis- 1 40-1392

engage control
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I087 0.015.0485.4 Starter switch 40-1392
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

J003 Preheating relay 40-1324

J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

40-623
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
J006b Preheating relay J006b
40-1290

Fig. 1132
Jd007 Starter relay 40-1392
M013 Engine control unit 40-1392
M014 Engine control unit 40-1392
Table 401
System Code P/N Description Characteristics/ Position Wiring loom
notes
N005 Starter motor “+30” 40-1329
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-624
Wiring diagrams
40.3.8 - S001 - Cab engine start - ITA (AGROFARM 410 -> ZKDW470200TD30001, AGRO-
FARM 420 -> ZKDW510200TD30001)

M013
M014

I087 Jd007 I079

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C017 C019

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.7845.4/20

Bd017 Bd018 Bd024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006 3 9 2

C018
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1 3 9 2

B001
60A

0.016.2001.4/10*

0.015.1418.4/30
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

8 9 18 15

-31
-31

+15
DIG.CLUTCH
J006a
J006b

J003
J004*

I007 H004
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1133
l A001 - +30 Battery
l A002 - Preheating device
l A006 - Starter motor “+50”
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A018 - Starter motor “+50”
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bd017 - Instrument panel fuse (key-on power) (10A)
l Bd018 - Engine ECU fuse (key-on power) (7.5A)
l Bd024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C017 - Earthing point
l C018 - Earthing point
l C019 - Earthing point
l D004 - Wiring connector for central wiring loom
l D004 - Wiring connector for rear wiring loom
l D006 - Wiring connector for central wiring loom
l D006 - Wiring connector for reverse shuttle wiring loom
l D010 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l H004 - Shuttle lever
l I007 - Start enable switch (transmission in neutral)
l I079 - Clutch engage-disengage control
l I087 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay

40-625
 Wiring diagrams

M013
M014

I087 Jd007 I079

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C017 C019

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.7845.4/20

Bd017 Bd018 Bd024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006 3 9 2

C018
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1 3 9 2

B001
60A

0.016.2001.4/10*

0.015.1418.4/30
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

8 9 18 15

-31
-31

+15
DIG.CLUTCH
J006a
J006b

J003
J004*

I007 H004
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1133
l Jd007 - Starter relay
l M013 - Engine ECU
l M014 - Engine ECU
l N005 - Starter motor “+30”
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 402
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A006 Starter motor “+50” 40-1324
A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A018 Starter motor “+50” 40-1327
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Bd017 Instrument panel 40-1392
fuse (key-on power)
(10A)
Bd018 Engine ECU fuse 40-1392
(key-on power)
(7.5A)
Bd024 Starter fuse (40A) 40-1392

40-626
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C017 Earthing point 40-1392
C018 Earthing point 40-1392
C019 Grounding point 40-1392
D004 Wiring connector for 40-1306
central wiring loom
D004 Wiring connector for 40-1306
central wiring loom
D006 Wiring connector for 40-1293
central wiring loom D006

F0130180

D006 Wiring connector for 40-1392

reverse shuttle wir- D006

ing loom
F0130180

D010 Wiring connector for 40-1324

central wiring loom
D010 Wiring connector for 40-1347
engine wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1392
power wiring loom
H004 Shuttle lever 40-1293
H004

I007 2.7659.343.0/10 Start enable switch 40-1306

(transmission in neu-
tral)
3,9 Ohm

I079 2.7659.097.0 Clutch engage-dis- 1 40-1392

engage control
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I087 0.015.0485.4 Starter switch 40-1392
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

40-627
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
J003 Preheating relay 40-1324
J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

J006b Preheating relay J006b

40-1290

Jd007 Starter relay 40-1392

Table 403
System Code P/N Description Characteristics/ Position Wiring loom
notes
M013 Engine control unit 40-1392
M014 Engine control unit 40-1392
N005 Starter motor “+30” 40-1329
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-628
Wiring diagrams
40.3.9 - S001 - Engine start, platform version - USA (AGROFARM 410 -> ZKD-
W350200TD25001, AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 ->
ZKDW430200TD25001)

M017
M018

I102 Jh007 I094

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C020 C022

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.8008.4

Bh017 Bh018 Bh024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006

3 9 2

C021
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1

B001
60A

0.016.2001.4/10*
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

J006a
J006b

J003
J004*

I007
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1134
l A001 - +30 Battery
l A002 - Preheating device
l A006 - Starter motor “+50”
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A018 - Starter motor “+50”
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bh017 - Instrument panel fuse (key-on power) (10A)
l Bh018 - Engine ECU fuse (key-on power) (7.5A)
l Bh024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C020 - Earthing point
l C021 - Earthing point
l C022 - Earthing point
l D004 - Wiring connector for central wiring loom
l D004 - Wiring connector for rear wiring loom
l D006 - Wiring connector for reverse shuttle wiring loom
l D010 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l I007 - Start enable switch (transmission in neutral)
l I094 - Clutch engage-disengage control
l I102 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay
l Jh007 - Starter relay

40-629
 Wiring diagrams

M017
M018

I102 Jh007 I094

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C020 C022

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.8008.4

Bh017 Bh018 Bh024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006

3 9 2

C021
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1

B001
60A

0.016.2001.4/10*
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

J006a
J006b

J003
J004*

I007
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1134
l M017 - Engine ECU
l M018 - Engine ECU
l N005 - Starter motor “+30”
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 404
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A006 Starter motor “+50” 40-1324
A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 0.015.0485.4 Battery negative ter- 40-1330
minal
A018 Starter motor “+50” 40-1327
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Bh017 Instrument panel 40-1410
fuse (key-on power)
(10A)
Bh018 Engine ECU fuse 40-1410
(key-on power)
(7.5A)
Bh024 Starter fuse (40A) 40-1410
C004 Earthing point 40-1330

40-630
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
C005 Earthing point 40-1330
C020 Grounding point 40-1410
C021 Grounding point 40-1410
C022 Grounding point 40-1410
D004 Wiring connector for 40-1306
central wiring loom
D004 Wiring connector for 40-1306
central wiring loom
D006 Wiring connector for 40-1392
reverse shuttle wir- D006

ing loom
F0130180

D010 Wiring connector for 40-1324

central wiring loom
D010 Wiring connector for 40-1410
central wiring loom
D040 Wiring connector for 40-1295
engine wiring loom
D040 Wiring connector for 40-1392
power wiring loom
I007 2.7659.343.0/10 Start enable switch 40-1306
(transmission in neu-
tral)
3,9 Ohm

I094 2.7659.097.0 Clutch engage-dis- 1 40-1410

engage control
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I102 0.015.0485.4 Starter switch 40-1410
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

J003 Preheating relay 40-1324

J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

40-631
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
J006b Preheating relay J006b
40-1290

Jh007 Starter relay 40-1410

M017 Engine control unit 40-1410
M018 Engine control unit 40-1410
Table 405
System Code P/N Description Characteristics/ Position Wiring loom
notes
N005 Starter motor “+30” 40-1329
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-632
Wiring diagrams
40.3.10 - S001 - Engine start, platform version - USA (AGROFARM 410 -> ZKD-
W470200TD30001, AGROFARM 420 -> ZKDW510200TD30001)

M017
M018

I102 Jh007 I094

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C020 C022

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.8008.4

Bh017 Bh018 Bh024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006 3 9 2

C021
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1 3 9 2

B001
60A

0.016.2001.4/10*

0.015.1418.4/30
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

8 9 18 15

-31
-31

+15
DIG.CLUTCH
J006a
J006b

J003
J004*

I007 H004
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1135
l A001 - +30 Battery
l A002 - Preheating device
l A006 - Starter motor “+50”
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A018 - Starter motor “+50”
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bh017 - Instrument panel fuse (key-on power) (10A)
l Bh018 - Engine ECU fuse (key-on power) (7.5A)
l Bh024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C020 - Earthing point
l C021 - Earthing point
l C022 - Earthing point
l D004 - Wiring connector for central wiring loom
l D004 - Wiring connector for rear wiring loom
l D006 - Wiring connector for central wiring loom
l D006 - Wiring connector for reverse shuttle wiring loom
l D010 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l D040 - Wiring connector for power wiring loom
l H004 - Shuttle lever
l I094 - Clutch engage-disengage control
l I102 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay

40-633
 Wiring diagrams

M017
M018

I102 Jh007 I094

START CONSENT
H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
50 15
C020 C022

+15
50 15 30 87 86 85 30 2 3 1 4 3 2 1 6 14
0.018.8008.4

Bh017 Bh018 Bh024

7,5 A

40 A
10A

D040 4 5 1 14 D010 D004 B-A3 A-A1 A-A8 A-D1 B-D1 D006 3 9 2

C021
0.015.1983.4/10

4 5 1 14 B-A3 A-A1 A-A8 A-D1 B-D1 3 9 2

B001
60A

0.016.2001.4/10*

0.015.1418.4/30
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002

C005
125A

C004*
A006
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A018* 1 2

8 9 18 15

-31
-31

+15
DIG.CLUTCH
J006a
J006b

J003
J004*

I007 H004
Q001* Q002* A015*
Q003 Q004 A016 A013

A014

N005
0.017.0474.4

GND +30
M
BATTERY

Fig. 1135
l Jh007 - Starter relay
l M017 - Engine ECU
l M018 - Engine ECU
l N005 - Starter motor “+30”
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 406
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A006 Starter motor “+50” 40-1324
A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A018 Starter motor “+50” 40-1327
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Bh017 Instrument panel 40-1410
fuse (key-on power)
(10A)
Bh018 Engine ECU fuse 40-1410
(key-on power)
(7.5A)
Bh024 Starter fuse (40A) 40-1410

40-634
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C020 Grounding point 40-1410
C021 Grounding point 40-1410
C022 Grounding point 40-1410
D004 Wiring connector for 40-1306
central wiring loom
D004 Wiring connector for 40-1306
central wiring loom
D006 Wiring connector for 40-1392
central wiring loom D006

F0130180

D006 Wiring connector for 40-1293

reverse shuttle wir- D006

ing loom
F0130180

D010 Wiring connector for 40-1324

central wiring loom
D010 Wiring connector for 40-1410
central wiring loom
D040 Wiring connector for 40-1295
engine wiring loom
D040 Wiring connector for 40-1392
power wiring loom
H004 Shuttle lever 40-1293
H004

I007 2.7659.343.0/10 Start enable switch 40-1306

(transmission in neu-
tral)
3,9 Ohm

I094 2.7659.097.0 Clutch engage-dis- 1 40-1410

engage control
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I102 0.015.0485.4 Starter switch 40-1410
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

40-635
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
J003 Preheating relay 40-1324
J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

J006b Preheating relay J006b

40-1290

Jh007 Starter relay 40-1410

M017 Engine control unit 40-1410
M018 Engine control unit 40-1410
Table 407
System Code P/N Description Characteristics/ Position Wiring loom
notes
N005 Starter motor “+30” 40-1329
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-636
Wiring diagrams
40.3.11 - S002 - Heating, standard cab (heater and air conditioning) - ITA

I035 Ja003 Ja008 Ja006

30
50 15
C007 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

Ba031

20 A
D031
B B D032
A A

Ba026 Ba016 Ba011 Ba023

30 A

15 A

30 A
3A

D012

C006

0.018.5825.4
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1136
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba023 - Fan/compressor fuse (30A)
l Ba026 - MK3 relay fuse 30A
l Ba031 - Ventilation/heating fuse (20A)
l C004 - Earthing point
l C005 - Earthing point
l C006 - Earthing point
l C007 - Earthing point

40-637
 Wiring diagrams
I035 Ja003 Ja008 Ja006
30
50 15
C007 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

Ba031

20 A
D031
B B D032
A A

Ba026 Ba016 Ba011 Ba023

30 A

15 A

30 A
3A

D012

C006

0.018.5825.4
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1136
l D012 - Wiring connector for roof wiring loom
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D025 - Wiring connector for roof wiring loom
l D025 - Wiring connector for air conditioner wiring loom
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector to cab wiring loom
l D032 - Wiring connector for roof wiring loom
l D039 - Wiring connector for power wiring loom
l D039 - Wiring connector for central cab wiring loom
l D040 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l I035 - Ignition switch
l Ja003 - Key-on power relay for fuses F11-12-13
l Ja006 - Fan relay
l Ja008 - Fan/compressor relay (key-on power)
l Q001 - Battery master switch
l Q002 - Battery master switch

40-638
Wiring diagrams
I035 Ja003 Ja008 Ja006
30
50 15
C007 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

Ba031

20 A
D031
B B D032
A A

Ba026 Ba016 Ba011 Ba023

30 A

15 A

30 A
3A

D012

C006

0.018.5825.4
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1136
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 408
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295

40-639
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Ba011 Turn indicator lights 40-1331
fuse (key-on power)
(15A)
Ba016 Relay fuse (key-on 40-1331
power) (3A)
Ba023 Fan/compressor 40-1331
fuse (30 A)
Ba026 MK3 relay fuse 30A 40-1331
Ba031 Ventilation/heating 40-1331
fuse (20A)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C006 Earthing point 40-1388
C007 Earthing point 40-1331
D012 Wiring connector for 40-1311
roof wiring loom
D012 Wiring connector for 40-1388
cab power wiring
loom
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1331
power wiring loom
D025 Wiring connector for 40-1274
roof wiring loom
D025

D025 Wiring connector for 40-1388

air conditioner wiring
loom
D031 Wiring connector for 40-1311
central wiring loom
D031 Wiring connector for 40-1331
cab power wiring
loom
D032 Wiring connector for 40-1311
roof wiring loom
D039 Wiring connector for 40-1331
power wiring loom
D039 Wiring connector for 40-1295
central cab wiring
loom
D040 Wiring connector for 40-1331
power wiring loom
D040 Wiring connector for 40-1331
central wiring loom
I035 Starter switch 40-1331
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

40-640
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Ja003 0.015.0485.4 Key-on power relay 40-1331
for fuses F11-12-13
Ja006 Fan relay 40-1331
Ja008 Fan/compressor re- 40-1331
lay (key-on power)
Q001 2.7659.351.0 Battery master 40-1330
switch

Table 409
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q002 2.7659.351.0 Battery master 40-1330
switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-641
 Wiring diagrams
40.3.12 - S002 - Heating, standard cab - ITA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)

I035 Ja003 Ja008 Ja006

30
50 15
C007 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

Ba031

20 A
D031
B B D032
A A

Ba026 Ba016 Ba011 Ba023

30 A

15 A

30 A
3A

D012

C003

0.016.0865.4/10
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1137
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba023 - Fan/compressor fuse (30A)
l Ba026 - MK3 relay fuse 30A
l Ba031 - Ventilation/heating fuse (20A)
l C003 - Earthing point
l C004 - Earthing point
l C005 - Earthing point
l C007 - Earthing point

40-642
Wiring diagrams

I035 Ja003 Ja008 Ja006

30
50 15
C007 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

Ba031

20 A
D031
B B D032
A A

Ba026 Ba016 Ba011 Ba023

30 A

15 A

30 A
3A

D012

C003

0.016.0865.4/10
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1137
l D012 - Wiring connector for roof wiring loom
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D025 - Wiring connector for roof wiring loom
l D025 - Wiring connector for air conditioner wiring loom
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector to cab wiring loom
l D032 - Wiring connector for roof wiring loom
l D039 - Wiring connector for power wiring loom
l D039 - Wiring connector for central cab wiring loom
l D040 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l H001 - Fan speed selector switch
l I035 - Ignition switch
l Ja003 - Key-on power relay for fuses F11-12-13
l Ja006 - Fan relay
l Ja008 - Fan/compressor relay (key-on power)
l N001 - Fan
l O001 - Resistor

40-643
 Wiring diagrams

I035 Ja003 Ja008 Ja006

30
50 15
C007 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

Ba031

20 A
D031
B B D032
A A

Ba026 Ba016 Ba011 Ba023

30 A

15 A

30 A
3A

D012

C003

0.016.0865.4/10
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1137
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

Table 410
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295

40-644
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Ba011 Turn indicator lights 40-1331
fuse (key-on power)
(15A)
Ba016 Relay fuse (key-on 40-1331
power) (3A)
Ba023 Fan/compressor 40-1331
fuse (30 A)
Ba026 MK3 relay fuse 30A 40-1331
Ba031 Ventilation/heating 40-1331
fuse (20A)
C003 Earthing point 40-1318
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C007 Earthing point 40-1331
D012 Wiring connector for 40-1311
roof wiring loom
D012 Wiring connector for 40-1388
cab power wiring
loom
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1331
power wiring loom
D025 Wiring connector for 40-1274
roof wiring loom
D025

D025 Wiring connector for T.W35.01.

air conditioner wiring L0.02.05.00.07
loom
D025

D031 Wiring connector for 40-1311

central wiring loom
D031 Wiring connector for 40-1331
cab power wiring
loom
D032 Wiring connector for 40-1311
roof wiring loom
D039 Wiring connector for 40-1331
power wiring loom
D039 Wiring connector for 40-1295
central cab wiring
loom
D040 Wiring connector for 40-1331
power wiring loom
D040 Wiring connector for 40-1331
central wiring loom
H001 Blower speed selec- 40-1274
tor switch

40-645
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
I035 0.015.0485.4 Starter switch 40-1331
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

Ja003 Key-on power relay 40-1331

for fuses F11-12-13
Ja006 Fan relay 40-1331
Ja008 Fan/compressor re- 40-1331
lay (key-on power)

Table 411
System Code P/N Description Characteristics/ Position Wiring loom
notes
N001 Electric fan N001
40-1274

O001 Resistor 40-1274

O001

Q001 2.7659.351.0 Battery master 40-1330

switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

40-646
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q004 2.7659.351.0 Battery master 40-1330
switch

40.3.13 - S002 - Heating, standard cab (heater and air conditioning) - USA

I045 Jb003 Jb008 Jb006

30
50 15
C010 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4081.4/30

Bb031
20 A

D031
B B D032
A A

D012
Bb026 Bb016 Bb011 Bb023
30 A

15 A

30 A
3A

C006

0.018.5825.4

D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2

2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1138
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal

40-647
 Wiring diagrams

I045 Jb003 Jb008 Jb006

30
50 15
C010 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4081.4/30

Bb031

20 A
D031
B B D032
A A

D012
Bb026 Bb016 Bb011 Bb023
30 A

15 A

30 A
3A

C006

0.018.5825.4
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1138
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb023 - Fan/compressor fuse (30A)
l Bb026 - MK3 relay fuse 30A
l Bb031 - Ventilation/heating fuse (20A)
l C004 - Earthing point
l C005 - Earthing point
l C006 - Earthing point
l C010 - Earthing point
l D012 - Wiring connector for roof wiring loom
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D025 - Wiring connector for roof wiring loom
l D025 - Wiring connector for air conditioner wiring loom
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector to cab wiring loom

40-648
Wiring diagrams

I045 Jb003 Jb008 Jb006

30
50 15
C010 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4081.4/30

Bb031

20 A
D031
B B D032
A A

D012
Bb026 Bb016 Bb011 Bb023
30 A

15 A

30 A
3A

C006

0.018.5825.4
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1138
l D032 - Wiring connector for roof wiring loom
l D039 - Wiring connector for power wiring loom
l D039 - Wiring connector for central cab wiring loom
l D040 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l I045 - Ignition switch
l Jb003 - Key-on power relay for fuses F11-12-13
l Jb006 - Fan relay
l Ja008 - Fan/compressor relay (key-on power)
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 412
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295

40-649
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Bb011 Turn indicator lights 40-1347
fuse (key-on power)
(15A)
Bb016 Relay fuse (key-on 40-1347
power) (3A)
Bb023 Fan/compressor 40-1347
fuse (30 A)
Bb026 MK3 relay fuse 30A 40-1347
Bb031 Ventilation/heating 40-1347
fuse (20A)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C006 Earthing point 40-1388
C010 Grounding point 40-1347
D012 Wiring connector for 40-1295
roof wiring loom
D012 Wiring connector for 40-1388
cab power wiring
loom
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1331
power wiring loom
D025 Wiring connector for 40-1274
roof wiring loom
D025

D025 Wiring connector for 40-1388

air conditioner wiring
loom
D025

D031 Wiring connector for 40-1295

central wiring loom
D031 Wiring connector for 40-1331
cab power wiring
loom
D032 Wiring connector for T.W35.01.
roof wiring loom L0.02.02.00.04
D039 Wiring connector for 40-1331
power wiring loom
D039 Wiring connector for 40-1295
central cab wiring
loom
D040 Wiring connector for 40-1331
power wiring loom
D040 Wiring connector for 40-1331
central wiring loom

40-650
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
I045 0.015.0485.4 Starter switch 40-1347
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

Jb003 Key-on power relay 40-1347

for fuses F11-12-13
Jb006 Fan relay 40-1347
Jb008 Fan/compressor re- 40-1347
lay (key-on power)
Q001 2.7659.351.0 Battery master 40-1330
switch

Table 413
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q002 2.7659.351.0 Battery master 40-1330
switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-651
 Wiring diagrams
40.3.14 - S002 - Heating, standard cab - USA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 -> ZKDW430200TD25001)
I045 Jb003 Jb008 Jb006
30
50 15
C010 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87

0.018.4081.4/30
Bb031

20 A
D031
B B
A A

D012
Bb026 Bb016 Bb011 Bb023

30 A

15 A

30 A
3A

D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1139
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb023 - Fan/compressor fuse (30A)
l Bb026 - MK3 relay fuse 30A
l Bb031 - Ventilation/heating fuse (20A)
l C003 - Earthing point
l C004 - Earthing point
l C005 - Earthing point
l C010 - Earthing point
l D012 - Wiring connector for roof wiring loom

40-652
Wiring diagrams
I045 Jb003 Jb008 Jb006
30
50 15
C010 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87

0.018.4081.4/30
Bb031

20 A
D031
B B
A A

D012
Bb026 Bb016 Bb011 Bb023

30 A

15 A

30 A
3A

D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1139
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D025 - Wiring connector for roof wiring loom
l D025 - Wiring connector for air conditioner wiring loom
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector to cab wiring loom
l D032 - Wiring connector for roof wiring loom
l D039 - Wiring connector for power wiring loom
l D039 - Wiring connector for central cab wiring loom
l D040 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l H001 - Fan speed selector switch
l I045 - Ignition switch
l Jb003 - Key-on power relay for fuses F11-12-13
l Jb006 - Fan relay
l Jb008 - Fan/compressor relay (key-on power)
l N001 - Fan
l O001 - Resistor
l Q001 - Battery master switch
l Q002 - Battery master switch

40-653
 Wiring diagrams
I045 Jb003 Jb008 Jb006
30
50 15
C010 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87

0.018.4081.4/30
Bb031

20 A
D031
B B
A A

D012
Bb026 Bb016 Bb011 Bb023

30 A

15 A

30 A
3A

D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N001 O001
0.017.8922.4/10*
0.015.1983.4/10

H001
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1139
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 414
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Bb011 Turn indicator lights 40-1347
fuse (key-on power)
(15A)

40-654
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Bb016 Relay fuse (key-on 40-1347
power) (3A)
Bb023 Fan/compressor 40-1347
fuse (30 A)
Bb026 MK3 relay fuse 30A 40-1347
Bb031 Ventilation/heating 40-1347
fuse (20A)
C003 Earthing point 40-1318
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C010 Grounding point 40-1347
D012 Wiring connector to [LNK]
cab wiring loom
D012 Wiring connector for [LNK]
roof power wiring
loom
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for [LNK]
power wiring loom
D025 Wiring connector for 40-1274
roof wiring loom
D025

D025 Wiring connector for T.W35.01.

air conditioner wiring L0.02.05.00.07
loom
D025

D031 Wiring connector for 40-1311

central wiring loom
D031 Wiring connector for 40-1331
cab power wiring
loom
D032 Wiring connector for 40-1311
roof wiring loom
D039 Wiring connector for 40-1331
power wiring loom
D039 Wiring connector for 40-1295
central cab wiring
loom
D040 Wiring connector for 40-1331
power wiring loom
D040 Wiring connector for 40-1331
central wiring loom
H001 Blower speed selec- 40-1274
tor switch
I045 0.015.0485.4 Starter switch 40-1347
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

40-655
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Jb003 Key-on power relay 40-1347
for fuses F11-12-13
Jb006 Fan relay 40-1347
Jb008 Fan/compressor re- 40-1347
lay (key-on power)

Table 415
System Code P/N Description Characteristics/ Position Wiring loom
notes
N001 Electric fan N001
40-1274

O001 Resistor 40-1274

O001

Q001 2.7659.351.0 Battery master 40-1330

switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-656
Wiring diagrams
40.3.15 - S002 - Heating, standard cab (heater and air conditioning) with electronic lift
(AGROFARM 430 -> ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001)
I061 Jc003 Jc008 Jc006
30
50 15
C013 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4537.4/40

Bc031

20 A
D031
B B D032
A A

D012
Bc026 Bc016 Bc011 Bc023
30 A

15 A

30 A
3A

C006

0.018.5825.4
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N002 O002
0.017.8922.4/10*
0.015.1983.4/10

H002
0.017.8922.4/10

A013 A011 A015* Q001* Q002*

A012 A015 Q001 Q002

BATTERY

Fig. 1140
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Bc011 - Turn indicator lights fuse (key-on power) (15A)
l Bc016 - Relay fuse (key-on power) (3A)
l Bc023 - Fan/compressor fuse (30A)
l Bc026 - MK3 relay fuse 30A
l Bc031 - Ventilation/heating fuse (20A)
l C004 - Earthing point
l C005 - Earthing point
l C006 - Earthing point
l D012 - Wiring connector for roof wiring loom
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D025 - Wiring connector for roof wiring loom
l D025 - Wiring connector for air conditioner wiring loom
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector for roof wiring loom
l D032 - Wiring connector for roof wiring loom
l D039 - Wiring connector for central cab wiring loom

40-657
 Wiring diagrams
I061 Jc003 Jc008 Jc006
30
50 15
C013 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87

0.018.4537.4/40

Bc031

20 A
D031
B B D032
A A

D012
Bc026 Bc016 Bc011 Bc023
30 A

15 A

30 A
3A

C006

0.018.5825.4
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N002 O002
0.017.8922.4/10*
0.015.1983.4/10

H002
0.017.8922.4/10

A013 A011 A015* Q001* Q002*

A012 A015 Q001 Q002

BATTERY

Fig. 1140
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for central wiring loom
l I061 - Ignition switch
l Jc003 - Key-on power relay for fuses F11-12-13
l Jc006 - Fan relay
l Ja008 - Fan/compressor relay (key-on power)
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 416
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Bc011 Turn indicator lights 40-1365
fuse (key-on power)
(15A)

40-658
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Bc016 Relay fuse (key-on 40-1365
power) (3A)
Bc023 Fan/compressor 40-1365
fuse (30 A)
Bc026 MK3 relay fuse 30A 40-1365
Bc031 Ventilation/heating 40-1365
fuse (20A)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C006 Earthing point 40-1388
D012 Wiring connector for 40-1311
roof wiring loom
D012 Wiring connector for 40-1311
cab power wiring
loom
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1365
power wiring loom
D025 Wiring connector for 40-1274
roof wiring loom
D025

D025 Wiring connector for 40-1388

air conditioner wiring
loom
D025

D031 Wiring connector for 40-1311

central wiring loom
D031 Wiring connector for 40-1311
roof wiring loom
D032 Wiring connector for 40-1311
roof wiring loom
D039 Wiring connector for 40-1295
central cab wiring
loom
D039 Wiring connector for 40-1365
power wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1365
power wiring loom
I061 0.015.0485.4 Starter switch 40-1365
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

Jc003 Key-on power relay 40-1365

for fuses F11-12-13
Jc006 Fan relay 40-1365
Jc008 Fan/compressor re- 40-1365
lay (key-on power)

40-659
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Table 417
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q003 2.7659.351.0 Battery master 40-1330
switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-660
Wiring diagrams
40.3.16 - S002 - Heating, standard cab with electronic lift (AGROFARM 430 -> ZKD-
W430200TD25001)
I061 Jc003 Jc008 Jc006
30
50 15
C013 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4537.4/40

Bc031

20 A
D031
B B D032
A A

D012
Bc026 Bc016 Bc011 Bc023
30 A

15 A

30 A
3A

C003

0.016.0865.4/10
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N002 O002
0.017.8922.4/10*
0.015.1983.4/10

H002
0.017.8922.4/10

A013 A011 A015* Q001* Q002*

A012 A015 Q001 Q002

BATTERY

Fig. 1141
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Bc011 - Turn indicator lights fuse (key-on power) (15A)
l Bc016 - Relay fuse (key-on power) (3A)
l Bc023 - Fan/compressor fuse (30A)
l Bc026 - MK3 relay fuse 30A
l Bc031 - Ventilation/heating fuse (20A)
l C003 - Earthing point
l C004 - Earthing point
l C005 - Earthing point
l D012 - Wiring connector for roof wiring loom
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D025 - Wiring connector for roof wiring loom
l D025 - Wiring connector for air conditioner wiring loom
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector for roof wiring loom
l D032 - Wiring connector for roof wiring loom
l D039 - Wiring connector for central cab wiring loom

40-661
 Wiring diagrams
I061 Jc003 Jc008 Jc006
30
50 15
C013 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87

0.018.4537.4/40

Bc031

20 A
D031
B B D032
A A

D012
Bc026 Bc016 Bc011 Bc023
30 A

15 A

30 A
3A

C003

0.016.0865.4/10
D040 D039 D013 1 2 D025

1 2

B001 B004 B003

60A

60A

60A

0.010.2147.2
2 1 1 2 3 L M H B L

C005 2
3

C004*
TF
M 1

N002 O002
0.017.8922.4/10*
0.015.1983.4/10

H002
0.017.8922.4/10

A013 A011 A015* Q001* Q002*

A012 A015 Q001 Q002

BATTERY

Fig. 1141
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for central wiring loom
l H004 - Fan speed selector switch
l I061 - Ignition switch
l Jc003 - Key-on power relay for fuses F11-12-13
l Jc006 - Fan relay
l Ja008 - Fan/compressor relay (key-on power)
l N001 - Fan
l O001 - Resistor
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 418
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295

40-662
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Bc011 Turn indicator lights 40-1365
fuse (key-on power)
(15A)
Bc016 Relay fuse (key-on 40-1365
power) (3A)
Bc023 Fan/compressor 40-1365
fuse (30 A)
Bc026 MK3 relay fuse 30A 40-1365
Bc031 Ventilation/heating 40-1365
fuse (20A)
C003 Earthing point 40-1318
C004 Earthing point 40-1330
C005 Earthing point 40-1330
D012 Wiring connector for 40-1311
roof wiring loom
D012 Wiring connector for 40-1311
cab power wiring
loom
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1365
power wiring loom
D025 Wiring connector for 40-1274
roof wiring loom
D025

D025 Wiring connector for 40-1388

air conditioner wiring
loom
D025

D031 Wiring connector for 40-1311

central wiring loom
D031 Wiring connector for 40-1311
roof wiring loom
D032 Wiring connector for 40-1311
roof wiring loom
D039 Wiring connector for 40-1295
central cab wiring
loom
D039 Wiring connector for 40-1365
power wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1365
power wiring loom
H001 Blower speed selec- 40-1274
tor switch
I061 0.015.0485.4 Starter switch 40-1365
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

40-663
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Jc003 Key-on power relay 40-1365
for fuses F11-12-13
Jc006 Fan relay 40-1365
Jc008 Fan/compressor re- 40-1365
lay (key-on power)
N001 Electric fan N001
40-1274

Table 419
System Code P/N Description Characteristics/ Position Wiring loom
notes
O001 Resistor 40-1274

O001

Q001 2.7659.351.0 Battery master 40-1330

switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-664
Wiring diagrams
40.3.17 - S003 - Air conditioning, standard cab
I035 Ja003 Ja008 Ja006
30
50 15
C007 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

Ba031

20 A
D031
B B D032
A A

D030
4 4
1 1

1 4

1 4
D029 D012
Ba026 Ba016 Ba011 Ba023 Ba025 Ba001
30 A

15 A

30 A

40 A

10 A
3A

Bg003

20 A
C006

D040 D039 D013 D010 13

0.018.5825.4 1 2 D026 4 1 2 3 D025 1 2 3 4 5 6 7 8 D028
13
1 2 4 1 2 3 1 2 3 4 5 6 7 8

B001 B004 B003

0.016.2001.4/10*
60A

60A

60A

0.016.2000.4/20

0.015.7266.4/40
0.010.2153.2

N016
N017* 2 1 1 2 3 L M H B L 1 2 30 85 86 87 6 5 2 3 1 2 4 6 8 A B A B 2 4 6 8

C005 2
3

C004*
TF
M M 1

0 J002 J001
N002 O002 H002 H003 J005 K017 P007 P008
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

A013 A011 A016 Q003 Q004

A012 A015* Q001* Q002*

BATTERY

Fig. 1142
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Ba001 - Air conditioning compressor fuse (10A)
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba023 - Fan/compressor fuse (30A)
l Ba025 - Protection fuse (40A)
l Ba026 - MK3 relay fuse 30A
l Ba031 - Ventilation/heating fuse (20A)
l Bg003 - 20A fuse (heating and climate control)
l C006 - Earthing point
l C007 - Earthing point
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D012 - Wiring connector for roof wiring loom
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D025 - Wiring connector for roof wiring loom
l D025 - Wiring connector for air conditioner wiring loom
l D026 - Wiring connector for roof wiring loom

40-665
 Wiring diagrams
I035 Ja003 Ja008 Ja006
30
50 15
C007 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

Ba031

20 A
D031
B B D032
A A

D030
4 4
1 1

1 4

1 4
D029 D012
Ba026 Ba016 Ba011 Ba023 Ba025 Ba001
30 A

15 A

30 A

40 A

10 A
3A

Bg003

20 A
C006

0.018.5825.4
D040 D039 D013 D010 13
1 2 D026 4 1 2 3 D025 1 2 3 4 5 6 7 8 D028
13
1 2 4 1 2 3 1 2 3 4 5 6 7 8

B001 B004 B003

0.016.2001.4/10*
60A

60A

60A

0.016.2000.4/20

0.015.7266.4/40
0.010.2153.2

N016
N017* 2 1 1 2 3 L M H B L 1 2 30 85 86 87 6 5 2 3 1 2 4 6 8 A B A B 2 4 6 8

C005 2
3

C004*
TF
M M 1

0 J002 J001
N002 O002 H002 H003 J005 K017 P007 P008
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

A013 A011 A016 Q003 Q004

A012 A015* Q001* Q002*

BATTERY

Fig. 1142
l D026 - Wiring connector for air conditioner wiring loom
l D028 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D028 - Wiring connector for roof wiring loom
l D029 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D029 - Wiring connector to cab power wiring loom
l D030 - Wiring connector for central cab wiring loom
l D030 - Wiring connector to cab power wiring loom
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector to cab power wiring loom
l D032 - Wiring connector for roof wiring loom
l D039 - Wiring connector for central cab wiring loom
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l H002 - Fan speed selector switch
l H003 - Air conditioning temperature thermostat
l I035 - Ignition switch
l J001 - Air conditioner heat exchanger fan control relay
l J002 - Auxiliary air conditioner heat exchanger fan control relay
l J005 - Compressor relay
l Ja003 - Key-on power relay for fuses F11-12-13
l Ja006 - Fan relay
l Ja008 - Fan/compressor relay (key-on power)
l K017 - Air conditioning pressure switch
l N002 - Fan
l N016 - Air conditioning compressor
l N017 - Air conditioning compressor
l O002 - Resistor
l P007 - Air conditioner heat exchanger fan

40-666
Wiring diagrams
I035 Ja003 Ja008 Ja006
30
50 15
C007 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

Ba031

20 A
D031
B B D032
A A

D030
4 4
1 1

1 4

1 4
D029 D012
Ba026 Ba016 Ba011 Ba023 Ba025 Ba001
30 A

15 A

30 A

40 A

10 A
3A

Bg003

20 A
C006

0.018.5825.4
D040 D039 D013 D010 13
1 2 D026 4 1 2 3 D025 1 2 3 4 5 6 7 8 D028
13
1 2 4 1 2 3 1 2 3 4 5 6 7 8

B001 B004 B003

0.016.2001.4/10*
60A

60A

60A

0.016.2000.4/20

0.015.7266.4/40
0.010.2153.2

N016
N017* 2 1 1 2 3 L M H B L 1 2 30 85 86 87 6 5 2 3 1 2 4 6 8 A B A B 2 4 6 8

C005 2
3

C004*
TF
M M 1

0 J002 J001
N002 O002 H002 H003 J005 K017 P007 P008
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

A013 A011 A016 Q003 Q004

A012 A015* Q001* Q002*

BATTERY

Fig. 1142
l P008 - Auxiliary air conditioning condenser fan
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 420
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Ba001 Air conditioning com- 40-1331
pressor fuse (10A)
Ba011 Turn indicator lights 40-1331
fuse (key-on power)
(15A)
Ba016 Relay fuse (key-on 40-1331
power) (3A)

40-667
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Ba023 Fan/compressor 40-1331
fuse (30 A)
Ba025 Protection fuse 40-1331
(40A)
Ba026 MK3 relay fuse 30A 40-1331
Ba031 Ventilation/heating 40-1331
fuse (20A)
Bg003 20A fuse (heating 40-1388
and climate control)
C006 Earthing point 40-1388
C007 Earthing point 40-1331
D010 Wiring connector for 40-1331
engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D012 Wiring connector for 40-1311
roof wiring loom
D012 Wiring connector for 40-1388
cab power wiring
loom
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1331
power wiring loom
D025 Wiring connector for 40-1275
roof wiring loom
D025

D025 Wiring connector for 40-1388

air conditioner wiring
loom
D025

D026 Wiring connector for 40-1275

roof wiring loom
D026 Wiring connector for 40-1388
air conditioner wiring
loom
D028 Wiring connector for 40-1388
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-1308
roof wiring loom
D029 Wiring connector for 40-1311
roof wiring loom
D029 Wiring connector for 40-1388
cab power wiring
loom
D030 Wiring connector for 40-1311
central cab wiring
loom
D030 Wiring connector for 40-1331
cab power wiring
loom
D031 Wiring connector for 40-1311
central wiring loom

40-668
Wiring diagrams
Table 421
System Code P/N Description Characteristics/ Position Wiring loom
notes
D031 Wiring connector for 40-1331
cab power wiring
loom
D032 Wiring connector for 40-1311
roof wiring loom
D039 Wiring connector for 40-1295
central cab wiring
loom
D039 Wiring connector for 40-1331
power wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1331
power wiring loom
H002 Blower speed selec- 40-1275
tor switch
H003 Air conditioning tem- 40-1275
perature thermostat
I035 0.015.0485.4 Starter switch 40-1331
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

J001 Air conditioner heat 40-1308

exchanger fan con-
trol relay
J002 Auxiliary air condi- 40-1308
tioner heat exchang-
er fan control relay
J005 Compressor relay 40-1275
Ja003 Key-on power relay 40-1331
for fuses F11-12-13
Ja006 Fan relay 40-1331
Ja008 Fan/compressor re- 40-1331
lay (key-on power)
K017 Air conditioning 40-1308
pressure switch
N002 Electric fan N002 40-1275

N016 Air conditioning 40-1324

compressor
N017 Air conditioning 40-1327
compressor
O002 Resistor 40-1275

O002

P007 Air conditioner heat 40-1308

exchanger fan

40-669
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
P008 Auxiliary conditioner 40-1308
heat exchanger fan
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-670
Wiring diagrams
40.3.18 - S003 - Air conditioning, cab with high visibility roof
I035 Ja003 Ja008 Ja006
30
50 15
C007
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

0.016.0373.4/30
Ba031

20 A
D031
B B
A A

D030
4 4
1 1

Ba026 Ba016 Ba011 Ba023 Ba025 Ba001

30 A

15 A

30 A

40 A

10 A
3A

D040 D039 D013 D010 13

1 4

13 1 4
D029 Be003
D012 D032 1 1
2 2 6

30 A
B001 B004 B003
D033 3
4
3
4
5
2 K017
60A

60A

60A

5 5 3
B B
A A 6 6 1
7 7
D034 8 8 2

B B
4
6
J002
A A
D028 8

A
B P007
C005
C004*
0.016.2001.4/10*

A
P008
0.016.2000.4/20

0.015.6272.4/40

B
0.017.8922.4/10*
0.017.9016.4/10
0.015.1983.4/10

2
4
6
J001
8

N016
N017* A B A B 87 85 86 30 86 30 87 87a 85 86 30 87 87a 85 1 2 3 4 1 2 3 4 5 4 3 2 1 1 2 1 4 2 1 2
A013 A011 A016 Q003 Q004
A012 A015* Q001* Q002* C023 0.015.7266.4/40
M M M
O004 O003
BATTERY N009 N008 Je002 Je001 Je003 mta H005 H007 I105 G003

Fig. 1143
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Ba001 - Air conditioning compressor fuse (10A)
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba023 - Fan/compressor fuse (30A)
l Ba025 - Protection fuse (40A)
l Ba026 - MK3 relay fuse 30A
l Ba031 - Ventilation/heating fuse (20A)
l Be003 - Fuse 3 in fuse box F (30A - Climate control)
l C004 - Earthing point
l C005 - Earthing point
l C007 - Earthing point
l C023 - Earthing point
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D012 - Wiring connector for roof wiring loom
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D028 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D028 - Wiring connector for roof wiring loom
l D029 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D029 - Wiring connector to cab power wiring loom
l D029 - Connection between cab power wiring loom and HV roof wiring loom
l D030 - Wiring connector for central cab wiring loom
l D030 - Wiring connector to cab power wiring loom

40-671
 Wiring diagrams
I035 Ja003 Ja008 Ja006
30
50 15
C007
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

0.016.0373.4/30
Ba031

20 A
D031
B B
A A

D030
4 4
1 1

Ba026 Ba016 Ba011 Ba023 Ba025 Ba001

30 A

15 A

30 A

40 A

10 A
3A

D040 D039 D013 D010 13

1 4

13 1 4
D029 Be003
D012 D032 1 1
2 2 6

30 A
B001 B004 B003
D033 3
4
3
4
5
2 K017
60A

60A

60A

5 5 3
B B
A A 6 6 1
7 7
D034 8 8 2

B B
4
6
J002
A A
D028 8

A
B P007
C005
C004*
0.016.2001.4/10*

A
P008
0.016.2000.4/20

0.015.6272.4/40

B
0.017.8922.4/10*
0.017.9016.4/10
0.015.1983.4/10

2
4
6
J001
8

N016
N017* A B A B 87 85 86 30 86 30 87 87a 85 86 30 87 87a 85 1 2 3 4 1 2 3 4 5 4 3 2 1 1 2 1 4 2 1 2
A013 A011 A016 Q003 Q004
A012 A015* Q001* Q002* C023 0.015.7266.4/40
M M M
O004 O003
BATTERY N009 N008 Je002 Je001 Je003 mta H005 H007 I105 G003

Fig. 1143
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector to cab power wiring loom
l D032 - Wiring connector for roof wiring loom
l D032 - Wiring connector to cab power wiring loom
l D033 - Wiring connector to wiring loom
l D033 - Wiring connector for roof
l D034 - Wiring connector to wiring loom
l D034 - Wiring connector for roof
l D039 - Wiring connector for central cab wiring loom
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l G003 - AC LED
l H005 - 4-speed fan control
l H007 - Mechanical thermostat
l I035 - Ignition switch
l I105 - Air conditioning switch
l J001 - Air conditioner heat exchanger fan control relay
l J002 - Auxiliary air conditioner heat exchanger fan control relay
l Ja003 - Key-on power relay for fuses F11-12-13
l Ja006 - Fan relay
l Ja008 - Fan/compressor relay (key-on power)
l Je0010 - Max fan speed relay
l Je002 - Compressor start relay
l Je003 - Third fan speed relay
l K017 - Air conditioning pressure switch
l N008 - RH electric fan
l N009 - LH electric fan
l N016 - Air conditioning compressor
l N017 - Air conditioning compressor
l O003 - LH resistor
l O004 - RH resistor
l P007 - Air conditioner heat exchanger fan
l P008 - Auxiliary air conditioning condenser fan

40-672
Wiring diagrams
I035 Ja003 Ja008 Ja006
30
50 15
C007
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.3567.4/60

0.016.0373.4/30
Ba031

20 A
D031
B B
A A

D030
4 4
1 1

Ba026 Ba016 Ba011 Ba023 Ba025 Ba001

30 A

15 A

30 A

40 A

10 A
3A

D040 D039 D013 D010 13

1 4

13 1 4
D029 Be003
D012 D032 1 1
2 2 6

30 A
B001 B004 B003
D033 3
4
3
4
5
2 K017
60A

60A

60A

5 5 3
B B
A A 6 6 1
7 7
D034 8 8 2

B B
4
6
J002
A A
D028 8

A
B P007
C005
C004*
0.016.2001.4/10*

A
P008
0.016.2000.4/20

0.015.6272.4/40

B
0.017.8922.4/10*
0.017.9016.4/10
0.015.1983.4/10

2
4
6
J001
8

N016
N017* A B A B 87 85 86 30 86 30 87 87a 85 86 30 87 87a 85 1 2 3 4 1 2 3 4 5 4 3 2 1 1 2 1 4 2 1 2
A013 A011 A016 Q003 Q004
A012 A015* Q001* Q002* C023 0.015.7266.4/40
M M M
O004 O003
BATTERY N009 N008 Je002 Je001 Je003 mta H005 H007 I105 G003

Fig. 1143
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

Table 422
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 [LNK]
A012 Battery +30 [LNK]
A013 Battery +30 [LNK]
A015 Battery negative ter- [LNK]
minal
A016 Battery negative ter- [LNK]
minal
B001 0.900.0783.1 60A fuse [LNK]
B003 0.900.0783.1 60A fuse [LNK]
B004 0.900.0783.1 60A fuse [LNK]
Ba001 Air conditioning com- [LNK]
pressor fuse (10A)
Ba011 Turn indicator lights [LNK]
fuse (key-on power)
(15A)
Ba016 Relay fuse (key-on [LNK]
power) (3A)
Ba023 Fan/compressor [LNK]
fuse (30 A)
Ba025 Protection fuse [LNK]
(40A)
Ba026 MK3 relay fuse 30A [LNK]
Ba031 Ventilation/heating [LNK]
fuse (20A)

40-673
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Be003 Fuse 3 in fuse box F [LNK]
(30A - Climate con-
trol)
C004 Grounding point [LNK]
C005 Grounding point [LNK]
C007 Grounding point [LNK]
C023 Grounding point [LNK]
D010 Wiring connector for [LNK]
engine wiring loom
D010 Wiring connector for [LNK]
central wiring loom
D012 Wiring connector for [LNK]
roof wiring loom
D012 Wiring connector for [LNK]
cab power wiring
loom
D013 Wiring connector for [LNK]
central wiring loom
D013 Wiring connector for [LNK]
power wiring loom
D028 Wiring connector for [LNK]
roof wiring loom
D028 Wiring connector for [LNK]
air conditioner heat
exchanger fan wiring
loom
D029 Wiring connector for [LNK]
roof wiring loom
D029 Wiring connector for [LNK]
cab power wiring
loom
D029 Connection between [LNK]
cab power supply
wiring and HV roof
wiring
D030 Wiring connector for [LNK]
central cab wiring
loom
D030 Wiring connector for [LNK]
cab power wiring
loom
D031 Wiring connector for [LNK]
central wiring loom
D031 Wiring connector for [LNK]
cab power wiring
loom

40-674
Wiring diagrams
Table 423
System Code P/N Description Characteristics/ Position Wiring loom
notes
D032 Wiring connector for [LNK] [LNK]
roof wiring loom
D032 Wiring connector for [LNK] [LNK]
cab power wiring
loom
D033 Wiring connector to [LNK] [LNK]
wiring loom
D033 Wiring connector for [LNK] [LNK]
roof
D034 Wiring connector to [LNK] [LNK]
wiring loom
D034 Wiring connector for [LNK] [LNK]
roof
D039 Wiring connector for [LNK] [LNK]
central cab wiring
loom
D039 Wiring connector for [LNK] [LNK]
power wiring loom
D040 Wiring connector for [LNK] [LNK]
central wiring loom
D040 Wiring connector for [LNK] [LNK]
power wiring loom
G003 AC LED [LNK] [LNK]
H005 4-speed fan control [LNK] [LNK]
H007 Mechanical thermo- [LNK] [LNK]
stat
I035 0.015.0485.4 Starter switch [LNK]
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

I105 Air conditioning [LNK] [LNK]

switch
J001 Air conditioner heat [LNK] [LNK]
exchanger fan con-
trol relay
J002 Auxiliary air condi- [LNK] [LNK]
tioner heat exchang-
er fan control relay
Ja003 Key-on power relay [LNK] [LNK]
for fuses F11-12-13
Ja006 Fan relay [LNK] [LNK]
Ja008 Fan/compressor re- [LNK] [LNK]
lay (key-on power)
Je001 Max fan speed relay [LNK] [LNK]
Je002 Compressor start [LNK] [LNK]
relay
Je003 Third fan speed re- [LNK] [LNK]
lay
K017 Air conditioning [LNK] [LNK]
pressure switch
N008 RH electric fan [LNK] [LNK]

40-675
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
N009 LH electric fan [LNK] [LNK]
N016 Air conditioning [LNK] [LNK]
compressor
N017 Air conditioning [LNK] [LNK]
compressor
O003 LH resistor [LNK] [LNK]
O004 RH resistor [LNK] [LNK]
P007 Air conditioner heat [LNK] [LNK]
exchanger fan
P008 Auxiliary conditioner [LNK] [LNK]
heat exchanger fan
Q001 2.7659.351.0 Battery master [LNK]
switch

Q002 2.7659.351.0 Battery master [LNK]

switch

Q003 2.7659.351.0 Battery master [LNK]

switch

40-676
Wiring diagrams
Table 424
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q004 2.7659.351.0 Battery master [LNK]
switch

40.3.19 - S003 - Air conditioning, cab with high visibility roof - USA
I045 Jb003 Jb008 Jb006
30
50 15
C010
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4081.4/30

0.016.0373.4/30
Bb031
20 A

D031
B B
A A

D030
4 4
1 1

Bb026 Bb016 Bb011 Bb023 Bb025 Bb001

30 A

15 A

30 A

40 A

10 A
3A

D040 D039 D013 D010 13

1 4

13 D029 1 4

Be003
D012 D032 1 1
2 2 6
30 A

B001 B004 B003

D033 3
4
3
4
5
2 K017
60A

60A

60A

5 5 3
B B
A A 6 6 1
7 7
D034 8 8 2

B B
4
6
J002
A A
D028 8

A
B P007
C005
C004*
0.016.2001.4/10*

A
P008
0.016.2000.4/20

0.015.6272.4/40

B
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

2
4
6
J001
8

N016
N017* A B A B 87 85 86 30 86 30 87 87a 85 86 30 87 87a 85 1 2 3 4 1 2 3 4 5 4 3 2 1 1 2 1 4 2 1 2
A013 A011 A015* Q001* Q002*
Q003 Q004 C023 0.015.7266.4/40
A012 A016
M M M
O004 O003
BATTERY N009 N008 Je002 Je001 Je003 mta H005 H007 I105 G003

Fig. 1144
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Bb001 - Air conditioning compressor fuse (10A)
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb023 - Fan/compressor fuse (30A)
l Bb025 - Protection fuse (40A)
l Bb026 - MK3 relay fuse 30A
l Bb031 - Ventilation/heating fuse (20A)
l Be003 - Fuse 3 in fuse box F (30A - Climate control)
l C004 - Earthing point
l C005 - Earthing point
l C010 - Earthing point

40-677
 Wiring diagrams
I045 Jb003 Jb008 Jb006
30
50 15
C010
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4081.4/30

0.016.0373.4/30
Bb031

20 A
D031
B B
A A

D030
4 4
1 1

Bb026 Bb016 Bb011 Bb023 Bb025 Bb001

30 A

15 A

30 A

40 A

10 A
3A

D040 D039 D013 D010 13

1 4

13 D029 1 4

Be003
D012 D032 1 1
2 2 6

30 A
B001 B004 B003
D033 3
4
3
4
5
2 K017
60A

60A

60A

5 5 3
B B
A A 6 6 1
7 7
D034 8 8 2

B B
4
6
J002
A A
D028 8

A
B P007
C005
C004*
0.016.2001.4/10*

A
P008
0.016.2000.4/20

0.015.6272.4/40

B
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

2
4
6
J001
8

N016
N017* A B A B 87 85 86 30 86 30 87 87a 85 86 30 87 87a 85 1 2 3 4 1 2 3 4 5 4 3 2 1 1 2 1 4 2 1 2
A013 A011 A015* Q001* Q002*
Q003 Q004 C023 0.015.7266.4/40
A012 A016
M M M
O004 O003
BATTERY N009 N008 Je002 Je001 Je003 mta H005 H007 I105 G003

Fig. 1144
l C023 - Earthing point
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D012 - Wiring connector for roof wiring loom
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D028 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D028 - Wiring connector for roof wiring loom
l D029 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D029 - Wiring connector to cab power wiring loom
l D029 - Connection between cab power wiring loom and HV roof wiring loom
l D030 - Wiring connector for central cab wiring loom
l D030 - Wiring connector to cab power wiring loom
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector to cab power wiring loom
l D032 - Wiring connector for roof wiring loom
l D032 - Wiring connector to cab power wiring loom
l D033 - Wiring connector to wiring loom
l D033 - Wiring connector for roof
l D034 - Wiring connector to wiring loom
l D034 - Wiring connector for roof
l D039 - Wiring connector for central cab wiring loom
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l G003 - AC LED
l H005 - 4-speed fan control
l H007 - Mechanical thermostat
l I045 - Ignition switch
l I105 - Air conditioning switch
l J001 - Air conditioner heat exchanger fan control relay
l J002 - Auxiliary air conditioner heat exchanger fan control relay
l Jb003 - Key-on power relay for fuses F11-12-13

40-678
Wiring diagrams
I045 Jb003 Jb008 Jb006
30
50 15
C010
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4081.4/30

0.016.0373.4/30
Bb031

20 A
D031
B B
A A

D030
4 4
1 1

Bb026 Bb016 Bb011 Bb023 Bb025 Bb001

30 A

15 A

30 A

40 A

10 A
3A

D040 D039 D013 D010 13

1 4

13 D029 1 4

Be003
D012 D032 1 1
2 2 6

30 A
B001 B004 B003
D033 3
4
3
4
5
2 K017
60A

60A

60A

5 5 3
B B
A A 6 6 1
7 7
D034 8 8 2

B B
4
6
J002
A A
D028 8

A
B P007
C005
C004*
0.016.2001.4/10*

A
P008
0.016.2000.4/20

0.015.6272.4/40

B
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

2
4
6
J001
8

N016
N017* A B A B 87 85 86 30 86 30 87 87a 85 86 30 87 87a 85 1 2 3 4 1 2 3 4 5 4 3 2 1 1 2 1 4 2 1 2
A013 A011 A015* Q001* Q002*
Q003 Q004 C023 0.015.7266.4/40
A012 A016
M M M
O004 O003
BATTERY N009 N008 Je002 Je001 Je003 mta H005 H007 I105 G003

Fig. 1144
l Jb006 - Fan relay
l Jb008 - Fan/compressor relay (key-on power)
l Je0010 - Max fan speed relay
l Je002 - Compressor start relay
l Je003 - Third fan speed relay
l K017 - Air conditioning pressure switch
l N008 - RH electric fan
l N009 - LH electric fan
l N016 - Air conditioning compressor
l N017 - Air conditioning compressor
l O003 - LH resistor
l O004 - RH resistor
l P007 - Air conditioner heat exchanger fan
l P008 - Auxiliary air conditioning condenser fan
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 425
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Bb001 Air conditioning com- 40-1347
pressor fuse (10A)

40-679
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Bb011 Turn indicator lights 40-1347
fuse (key-on power)
(15A)
Bb016 Relay fuse (key-on 40-1347
power) (3A)
Bb023 Fan/compressor 40-1347
fuse (30 A)
Bb025 Protection fuse 40-1347
(40A)
Bb026 MK3 relay fuse 30A 40-1347
Bb031 Ventilation/heating 40-1347
fuse (20A)
Be003 Fuse 3 in fuse box F 40-1301
(30A - Climate con-
trol)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C010 Grounding point 40-1347
C023 Grounding point 40-1301
D010 Wiring connector for 40-1331
engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D012 Wiring connector for 40-1311
roof wiring loom
D012 Wiring connector for 40-1301
cab power wiring
loom
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1331
power wiring loom
D028 Wiring connector for 40-1308
roof wiring loom
D028 Wiring connector for 40-1301
air conditioner heat
exchanger fan wiring
loom
D029 Wiring connector for 40-1311
roof wiring loom
D029 Wiring connector for 40-1301
cab power wiring
loom
D029 Connection between 40-1301
cab power supply
wiring and HV roof
wiring
D030 Wiring connector for 40-1311
central cab wiring
loom
D030 Wiring connector for 40-1331
cab power wiring
loom
D031 Wiring connector for 40-1311
central wiring loom

40-680
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
D031 Wiring connector for 40-1331
cab power wiring
loom
Table 426
System Code P/N Description Characteristics/ Position Wiring loom
notes
D032 Wiring connector for [LNK] 40-1311
roof wiring loom
D032 Wiring connector for [LNK] 40-1301
cab power wiring
loom
D033 Wiring connector to [LNK] 40-1301
wiring loom
D033 Wiring connector for [LNK] 40-1301
roof
D034 Wiring connector to [LNK] 40-1301
wiring loom
D034 Wiring connector for [LNK] 40-1301
roof
D039 Wiring connector for [LNK] 40-1295
central cab wiring
loom
D039 Wiring connector for [LNK] 40-1331
power wiring loom
D040 Wiring connector for [LNK] 40-1295
central wiring loom
D040 Wiring connector for [LNK] 40-1331
power wiring loom
G003 AC LED [LNK] 40-1301
H005 4-speed fan control [LNK] 40-1301
H007 Mechanical thermo- [LNK] 40-1301
stat
I045 0.015.0485.4 Starter switch 40-1347
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

I105 Air conditioning [LNK] 40-1301

switch
J001 Air conditioner heat [LNK] 40-1308
exchanger fan con-
trol relay
J002 Auxiliary air condi- [LNK] 40-1308
tioner heat exchang-
er fan control relay
Jb003 Key-on power relay [LNK] 40-1347
for fuses F11-12-13
Jb006 Fan relay [LNK] 40-1347
Jb008 Fan/compressor re- [LNK] 40-1347
lay (key-on power)
Je001 Max fan speed relay [LNK] 40-1301

40-681
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Je002 Compressor start [LNK] 40-1301
relay
Je003 Third fan speed re- [LNK] 40-1301
lay
K017 Air conditioning [LNK] 40-1308
pressure switch
N008 RH electric fan [LNK] 40-1301
N009 LH electric fan [LNK] 40-1301
N016 Air conditioning [LNK] 40-1324
compressor
N017 Air conditioning [LNK] 40-1327
compressor
O003 LH resistor [LNK] 40-1301
O004 RH resistor [LNK] 40-1301
P007 Air conditioner heat [LNK] 40-1308
exchanger fan
P008 Auxiliary conditioner [LNK] 40-1308
heat exchanger fan
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

40-682
Wiring diagrams
Table 427
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q004 2.7659.351.0 Battery master 40-1330
switch

40.3.20 - S003 - Air conditioning, standard cab - USA

I045 Jb003 Jb008 Jb006
30
50 15
C010 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4081.4/30

Bb031
20 A

D031
B B D032
A A

D030
4 4
1 1

1 4

1 4
D029 D012
Bb026 Bb016 Bb011 Bb023 Bb025 Bb001
30 A

15 A

30 A

40 A

10 A
3A

Bg003

20 A
C006
0.018.5825.4

D040 D039 D013 D010 13

1 2 D026 4 1 2 3 D025 1 2 3 4 5 6 7 8 D028
13
1 2 4 1 2 3 1 2 3 4 5 6 7 8

B001 B004 B003

0.016.2001.4/10*
60A

60A

60A

0.015.7266.4/40
0.016.2000.4/20

0.010.2153.2

N016
N017* 2 1 1 2 3 L M H B L 1 2 30 85 86 87 6 5 2 3 1 2 4 6 8 A B A B 2 4 6 8

C005 2
3

C004*
TF
M M 1

0 J002 J001
N002 O002 H002 H003 J005 K017 P007 P008
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

A013 A011 A016 Q003 Q004

A012 A015* Q001* Q002*

BATTERY

Fig. 1145
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Bb001 - Air conditioning compressor fuse (10A)
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb023 - Fan/compressor fuse (30A)
l Bb025 - Protection fuse (40A)

40-683
 Wiring diagrams
I045 Jb003 Jb008 Jb006
30
50 15
C010 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4081.4/30

Bb031

20 A
D031
B B D032
A A

D030
4 4
1 1

1 4

1 4
D029 D012
Bb026 Bb016 Bb011 Bb023 Bb025 Bb001
30 A

15 A

30 A

40 A

10 A
3A

Bg003

20 A
C006

0.018.5825.4
D040 D039 D013 D010 13
1 2 D026 4 1 2 3 D025 1 2 3 4 5 6 7 8 D028
13
1 2 4 1 2 3 1 2 3 4 5 6 7 8

B001 B004 B003

0.016.2001.4/10*
60A

60A

60A

0.015.7266.4/40
0.016.2000.4/20

0.010.2153.2

N016
N017* 2 1 1 2 3 L M H B L 1 2 30 85 86 87 6 5 2 3 1 2 4 6 8 A B A B 2 4 6 8

C005 2
3

C004*
TF
M M 1

0 J002 J001
N002 O002 H002 H003 J005 K017 P007 P008
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

A013 A011 A016 Q003 Q004

A012 A015* Q001* Q002*

BATTERY

Fig. 1145
l Bb026 - MK3 relay fuse 30A
l Bb031 - Ventilation/heating fuse (20A)
l Bg003 - 20A fuse (heating and climate control)
l C006 - Earthing point
l C010 - Earthing point
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D012 - Wiring connector for roof wiring loom
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D025 - Wiring connector for roof wiring loom
l D025 - Wiring connector for air conditioner wiring loom
l D026 - Wiring connector for roof wiring loom
l D026 - Wiring connector for air conditioner wiring loom
l D028 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D028 - Wiring connector for roof wiring loom
l D029 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D029 - Wiring connector to cab power wiring loom
l D030 - Wiring connector for central cab wiring loom
l D030 - Wiring connector to cab power wiring loom
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector to cab power wiring loom
l D032 - Wiring connector for roof wiring loom
l D039 - Wiring connector for central cab wiring loom
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l H002 - Fan speed selector switch

40-684
Wiring diagrams
I045 Jb003 Jb008 Jb006
30
50 15
C010 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4081.4/30

Bb031

20 A
D031
B B D032
A A

D030
4 4
1 1

1 4

1 4
D029 D012
Bb026 Bb016 Bb011 Bb023 Bb025 Bb001
30 A

15 A

30 A

40 A

10 A
3A

Bg003

20 A
C006

0.018.5825.4
D040 D039 D013 D010 13
1 2 D026 4 1 2 3 D025 1 2 3 4 5 6 7 8 D028
13
1 2 4 1 2 3 1 2 3 4 5 6 7 8

B001 B004 B003

0.016.2001.4/10*
60A

60A

60A

0.015.7266.4/40
0.016.2000.4/20

0.010.2153.2

N016
N017* 2 1 1 2 3 L M H B L 1 2 30 85 86 87 6 5 2 3 1 2 4 6 8 A B A B 2 4 6 8

C005 2
3

C004*
TF
M M 1

0 J002 J001
N002 O002 H002 H003 J005 K017 P007 P008
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

A013 A011 A016 Q003 Q004

A012 A015* Q001* Q002*

BATTERY

Fig. 1145
l H003 - Air conditioning temperature thermostat
l I045 - Ignition switch
l J001 - Air conditioner heat exchanger fan control relay
l J002 - Auxiliary air conditioner heat exchanger fan control relay
l J005 - Compressor relay
l Jb003 - Key-on power relay for fuses F11-12-13
l Jb006 - Fan relay
l Jb008 - Fan/compressor relay (key-on power)
l K017 - Air conditioning pressure switch
l N002 - Fan
l N016 - Air conditioning compressor
l N017 - Air conditioning compressor
l O002 - Resistor
l P007 - Air conditioner heat exchanger fan
l P008 - Auxiliary air conditioning condenser fan
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

40-685
 Wiring diagrams
Table 428
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Bb001 Air conditioning com- 40-1347
pressor fuse (10A)
Bb011 Turn indicator lights 40-1347
fuse (key-on power)
(15A)
Bb016 Relay fuse (key-on 40-1347
power) (3A)
Bb023 Fan/compressor 40-1347
fuse (30 A)
Bb025 Protection fuse 40-1347
(40A)
Bb026 MK3 relay fuse 30A 40-1347
Bb031 Ventilation/heating 40-1347
fuse (20A)
Bg003 20A fuse (heating 40-1388
and climate control)
C006 Earthing point 40-1388
C010 Grounding point 40-1347
D010 Wiring connector for 40-1331
engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D012 Wiring connector for 40-1311
roof wiring loom
D012 Wiring connector for 40-1388
cab power wiring
loom
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1331
power wiring loom
D025 Wiring connector for 40-1275
roof wiring loom
D025

D025 Wiring connector for 40-1388

air conditioner wiring
loom
D025

D026 Wiring connector for 40-1275

roof wiring loom
D026 Wiring connector for 40-1388
air conditioner wiring
loom

40-686
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
D028 Wiring connector for 40-1388
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-1308
roof wiring loom
D029 Wiring connector for 40-1311
roof wiring loom
D029 Wiring connector for 40-1388
cab power wiring
loom
D030 Wiring connector for 40-1311
central cab wiring
loom
D030 Wiring connector for 40-1331
cab power wiring
loom
D031 Wiring connector for 40-1311
central wiring loom
Table 429
System Code P/N Description Characteristics/ Position Wiring loom
notes
D031 Wiring connector for 40-1331
cab power wiring
loom
D032 Wiring connector for 40-1311
roof wiring loom
D039 Wiring connector for 40-1295
central cab wiring
loom
D039 Wiring connector for 40-1331
power wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1331
power wiring loom
H002 Blower speed selec- 40-1275
tor switch
H003 Air conditioning tem- 40-1275
perature thermostat
I045 0.015.0485.4 Starter switch 40-1347
J001 Air conditioner heat 40-1308
exchanger fan con-
trol relay
J002 Auxiliary air condi- 40-1308
tioner heat exchang-
er fan control relay
J005 Compressor relay 40-1275
Jb003 Key-on power relay 40-1347
for fuses F11-12-13
Jb006 Fan relay 40-1347
Jb008 Fan/compressor re- 40-1347
lay (key-on power)
K017 Air conditioning 40-1308
pressure switch

40-687
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
N002 Electric fan N002 40-1275

Fig. 1146
N016 Air conditioning 40-1324
compressor
N017 Air conditioning 40-1327
compressor
O002 Resistor 40-1275

O002

Fig. 1147
P007 Air conditioner heat 40-1308
exchanger fan
P008 Auxiliary conditioner 40-1308
heat exchanger fan
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-688
Wiring diagrams
40.3.21 - S003 - Air conditioning, standard cab with electronic lift (AGROFARM 430 ->
ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001)
I061 Jc003 Jc008 Jc006
30
50 15
C013 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4537.4/40

Bc031

20 A
D031
B B D032
A A

D030
4 4
1 1

1 4

1 4
D029 D012
Bc026 Bc016 Bc011 Bc023 Bc025 Bc001
30 A

15 A

30 A

40 A

10 A
3A

Bg003

20 A
C006

0.018.5825.4

D040 D039 D013 D035 13

1 2 D026 4 1 2 3 D027 1 2 3 4 5 6 7 8 D028
13
1 2 4 1 2 3 1 2 3 4 5 6 7 8

B001 B004 B003

0.016.2001.4/10*
60A

60A

60A

0.016.2001.4/10

0.015.7266.4/40
0.016.2000.4/20

0.010.2153.2

N016
N017* 2 1 1 2 3 L M H B L 1 2 30 85 86 87 6 5 2 3 1 2 4 6 8 A B A B 2 4 6 8

C005 2
3

C004*
TF
M M 1

0 J002 J001
N002 O002 H002 H003 J005 K017 P007 P008
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1148
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Bc001 - Air conditioning compressor fuse (10A)
l Bc011 - Turn indicator lights fuse (key-on power) (15A)
l Bc016 - Relay fuse (key-on power) (3A)
l Bc023 - Fan/compressor fuse (30A)
l Bc025 - Protection fuse (40A)
l Bc026 - MK3 relay fuse 30A
l Bc031 - Ventilation/heating fuse (20A)
l Bg003 - 20A fuse (heating and climate control)
l C006 - Earthing point
l C013 - Earthing point
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D012 - Wiring connector for roof wiring loom
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D025 - Wiring connector for roof wiring loom
l D025 - Wiring connector for air conditioner wiring loom

40-689
 Wiring diagrams
I061 Jc003 Jc008 Jc006
30
50 15
C013 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4537.4/40

Bc031

20 A
D031
B B D032
A A

D030
4 4
1 1

1 4

1 4
D029 D012
Bc026 Bc016 Bc011 Bc023 Bc025 Bc001
30 A

15 A

30 A

40 A

10 A
3A

Bg003

20 A
C006

0.018.5825.4
D040 D039 D013 D035 13
1 2 D026 4 1 2 3 D027 1 2 3 4 5 6 7 8 D028
13
1 2 4 1 2 3 1 2 3 4 5 6 7 8

B001 B004 B003

0.016.2001.4/10*
60A

60A

60A

0.016.2001.4/10

0.015.7266.4/40
0.016.2000.4/20

0.010.2153.2

N016
N017* 2 1 1 2 3 L M H B L 1 2 30 85 86 87 6 5 2 3 1 2 4 6 8 A B A B 2 4 6 8

C005 2
3

C004*
TF
M M 1

0 J002 J001
N002 O002 H002 H003 J005 K017 P007 P008
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1148
l D026 - Wiring connector for roof wiring loom
l D026 - Wiring connector for air conditioner wiring loom
l D028 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D028 - Wiring connector for roof wiring loom
l D029 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D029 - Wiring connector to cab power wiring loom
l D030 - Wiring connector for central cab wiring loom
l D030 - Wiring connector to cab power wiring loom
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector to cab power wiring loom
l D032 - Wiring connector for roof wiring loom
l D039 - Wiring connector for central cab wiring loom
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l H002 - Fan speed selector switch
l H003 - Air conditioning temperature thermostat
l I061 - Ignition switch
l J001 - Air conditioner heat exchanger fan control relay
l J002 - Auxiliary air conditioner heat exchanger fan control relay
l J005 - Compressor relay
l Jc003 - Key-on power relay for fuses F11-12-13
l Jc006 - Fan relay
l Ja008 - Fan/compressor relay (key-on power)
l K017 - Air conditioning pressure switch
l N002 - Fan
l N016 - Air conditioning compressor
l N017 - Air conditioning compressor
l O002 - Resistor

40-690
Wiring diagrams
I061 Jc003 Jc008 Jc006
30
50 15
C013 0.016.0373.4/30
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4537.4/40

Bc031

20 A
D031
B B D032
A A

D030
4 4
1 1

1 4

1 4
D029 D012
Bc026 Bc016 Bc011 Bc023 Bc025 Bc001
30 A

15 A

30 A

40 A

10 A
3A

Bg003

20 A
C006

0.018.5825.4
D040 D039 D013 D035 13
1 2 D026 4 1 2 3 D027 1 2 3 4 5 6 7 8 D028
13
1 2 4 1 2 3 1 2 3 4 5 6 7 8

B001 B004 B003

0.016.2001.4/10*
60A

60A

60A

0.016.2001.4/10

0.015.7266.4/40
0.016.2000.4/20

0.010.2153.2

N016
N017* 2 1 1 2 3 L M H B L 1 2 30 85 86 87 6 5 2 3 1 2 4 6 8 A B A B 2 4 6 8

C005 2
3

C004*
TF
M M 1

0 J002 J001
N002 O002 H002 H003 J005 K017 P007 P008
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004

BATTERY

Fig. 1148
l P007 - Air conditioner heat exchanger fan
l P008 - Auxiliary air conditioning condenser fan
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 430
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Bc001 Air conditioning com- 40-1365
pressor fuse (10A)
Bc011 Turn indicator lights 40-1365
fuse (key-on power)
(15A)
Bc016 Relay fuse (key-on 40-1365
power) (3A)

40-691
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Bc023 Fan/compressor 40-1365
fuse (30 A)
Bc025 Protection fuse 40-1365
(40A)
Bc026 MK3 relay fuse 30A 40-1365
Bc031 Ventilation/heating 40-1365
fuse (20A)
Bg003 20A fuse (heating 40-1388
and climate control)
C006 Earthing point 40-1388
C013 Earthing point 40-1365
D010 Wiring connector for 40-1331
engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D012 Wiring connector for 40-1311
roof wiring loom
D012 Wiring connector for 40-1388
cab power wiring
loom
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1331
power wiring loom
D025 Wiring connector for 40-1275
roof wiring loom
D025

D025 Wiring connector for 40-1388

air conditioner wiring
loom
D025

D026 Wiring connector for 40-1275

roof wiring loom
D026 Wiring connector for 40-1388
air conditioner wiring
loom
D028 Wiring connector for 40-1388
air conditioner heat
exchanger fan wiring
loom
D028 Wiring connector for 40-1308
roof wiring loom
D029 Wiring connector for 40-1311
roof wiring loom
D029 Wiring connector for 40-1388
cab power wiring
loom
D030 Wiring connector for 40-1311
central cab wiring
loom
D030 Wiring connector for 40-1331
cab power wiring
loom
D031 Wiring connector for 40-1311
central wiring loom

40-692
Wiring diagrams
Table 431
System Code P/N Description Characteristics/ Position Wiring loom
notes
D031 Wiring connector for 40-1331
cab power wiring
loom
D032 Wiring connector for 40-1311
roof wiring loom
D039 Wiring connector for 40-1295
central cab wiring
loom
D039 Wiring connector for 40-1331
power wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1331
power wiring loom
H002 Blower speed selec- 40-1275
tor switch
H003 Air conditioning tem- 40-1275
perature thermostat
I061 0.015.0485.4 Starter switch 40-1365
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

J001 Air conditioner heat 40-1308

exchanger fan con-
trol relay
J002 Auxiliary air condi- 40-1308
tioner heat exchang-
er fan control relay
J005 Compressor relay 40-1275
Jc003 Key-on power relay 40-1365
for fuses F11-12-13
Jc006 Fan relay 40-1365
Jc008 Fan/compressor re- 40-1365
lay (key-on power)
K017 Air conditioning 40-1308
pressure switch
N002 Electric fan N002 40-1275

N016 Air conditioning 40-1324

compressor
N017 Air conditioning 40-1327
compressor
O002 Resistor 40-1275

O002

P007 Air conditioner heat 40-1308

exchanger fan

40-693
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
P008 Auxiliary conditioner 40-1308
heat exchanger fan
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-694
Wiring diagrams
40.3.22 - S003 - Air conditioning, cab with high visibility roof and electronic lift (AGRO-
FARM 430 -> ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001)
I061 Jc003 Jc008 Jc006
30
50 15
C013
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4537.4/40

0.016.0373.4/30
Bc031

20 A
D031
B B
A A

D030
4 4
1 1

Bc026 Bc016 Bc011 Bc023 Bc025 Bc001

30 A

15 A

30 A

40 A

10 A
3A

D040 D039 D013 D035 13

1 4

13 D029 1 4

Be003
D012 D032 1 1
2 2 6

30 A
B001 B004 B003
D033 3
4
3
4
5
2 K017
0.016.2001.4/10*
60A

60A

60A

5 5
0.016.2000.4/20

B B 3
A A 6 6 1
7 7
D034 8 8 2

B B
4
6
J002
A A
D028 8

N016
A
N017*
B P007
C005
C004* M A
P008
0.015.6272.4/40

B
0.017.8922.4/10*
0.015.1983.4/10

0.017.8922.4/10

2
4
6
J001
8

A B A B 87 85 86 30 86 30 87 87a 85 86 30 87 87a 85 1 2 3 4 1 2 3 4 5 4 3 2 1 1 2 1 4 2 1 2
A013 A011 A015* Q001* Q002*
C023 0.015.7266.4/40
A012 A016 Q003 Q004
M M
O004 O003
BATTERY N009 N008 Je002 Je001 Je003 ??? H005 H007 I105 G005

Fig. 1149
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Bc001 - Air conditioning compressor fuse (10A)
l Bc011 - Turn indicator lights fuse (key-on power) (15A)
l Bc016 - Relay fuse (key-on power) (3A)
l Bc023 - Fan/compressor fuse (30A)
l Bc025 - Protection fuse (40A)
l Bc026 - MK3 relay fuse 30A
l Bc031 - Ventilation/heating fuse (20A)
l Be003 - Fuse 3 in fuse box F (30A - Climate control)
l C004 - Earthing point
l C005 - Earthing point
l C013 - Earthing point
l C023 - Earthing point
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D012 - Wiring connector for roof wiring loom
l D012 - Wiring connector to cab power wiring loom
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D028 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D028 - Wiring connector for roof wiring loom
l D029 - Wiring connector for air conditioner heat exchanger fan wiring loom
l D029 - Wiring connector to cab power wiring loom
l D029 - Connection between cab power wiring loom and HV roof wiring loom
l D030 - Wiring connector for central cab wiring loom

40-695
 Wiring diagrams
I061 Jc003 Jc008 Jc006
30
50 15
C013
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4537.4/40

0.016.0373.4/30
Bc031

20 A
D031
B B
A A

D030
4 4
1 1

Bc026 Bc016 Bc011 Bc023 Bc025 Bc001

30 A

15 A

30 A

40 A

10 A
3A

D040 D039 D013 D035 13

1 4

13 D029 1 4

Be003
D012 D032 1 1
2 2 6

30 A
B001 B004 B003
D033 3
4
3
4
5
2 K017
0.016.2001.4/10*
60A

60A

60A

5 5
0.016.2000.4/20

B B 3
A A 6 6 1
7 7
D034 8 8 2

B B
4
6
J002
A A
D028 8

N016
A
N017*
B P007
C005
C004* M A
P008
0.015.6272.4/40

B
0.017.8922.4/10*
0.015.1983.4/10

0.017.8922.4/10

2
4
6
J001
8

A B A B 87 85 86 30 86 30 87 87a 85 86 30 87 87a 85 1 2 3 4 1 2 3 4 5 4 3 2 1 1 2 1 4 2 1 2
A013 A011 A015* Q001* Q002*
C023 0.015.7266.4/40
A012 A016 Q003 Q004
M M
O004 O003
BATTERY N009 N008 Je002 Je001 Je003 ??? H005 H007 I105 G005

Fig. 1149
l D030 - Wiring connector to cab power wiring loom
l D031 - Wiring connector for central wiring loom
l D031 - Wiring connector to cab power wiring loom
l D032 - Wiring connector for roof wiring loom
l D032 - Wiring connector to cab power wiring loom
l D033 - Wiring connector to wiring loom
l D033 - Wiring connector for roof
l D034 - Wiring connector to wiring loom
l D034 - Wiring connector for roof
l D039 - Wiring connector for central cab wiring loom
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l G003 - AC LED
l H005 - 4-speed fan control
l H007 - Mechanical thermostat
l I061 - Ignition switch
l I105 - Air conditioning switch
l J001 - Air conditioner heat exchanger fan control relay
l J002 - Auxiliary air conditioner heat exchanger fan control relay
l Jc003 - Key-on power relay for fuses F11-12-13
l Jc006 - Fan relay
l Ja008 - Fan/compressor relay (key-on power)
l Je0010 - Max fan speed relay
l Je002 - Compressor start relay
l Je003 - Third fan speed relay
l K017 - Air conditioning pressure switch
l N008 - RH electric fan
l N009 - LH electric fan
l N016 - Air conditioning compressor
l N017 - Air conditioning compressor
l O003 - LH resistor
l O004 - RH resistor
l P007 - Air conditioner heat exchanger fan

40-696
Wiring diagrams
I061 Jc003 Jc008 Jc006
30
50 15
C013
50 15 30 30 85 86 87 30 85 86 87 30 86 85 87
0.018.4537.4/40

0.016.0373.4/30
Bc031

20 A
D031
B B
A A

D030
4 4
1 1

Bc026 Bc016 Bc011 Bc023 Bc025 Bc001

30 A

15 A

30 A

40 A

10 A
3A

D040 D039 D013 D035 13

1 4

13 D029 1 4

Be003
D012 D032 1 1
2 2 6

30 A
B001 B004 B003
D033 3
4
3
4
5
2 K017
0.016.2001.4/10*
60A

60A

60A

5 5
0.016.2000.4/20

B B 3
A A 6 6 1
7 7
D034 8 8 2

B B
4
6
J002
A A
D028 8

N016
A
N017*
B P007
C005
C004* M A
P008
0.015.6272.4/40

B
0.017.8922.4/10*
0.015.1983.4/10

0.017.8922.4/10

2
4
6
J001
8

A B A B 87 85 86 30 86 30 87 87a 85 86 30 87 87a 85 1 2 3 4 1 2 3 4 5 4 3 2 1 1 2 1 4 2 1 2
A013 A011 A015* Q001* Q002*
C023 0.015.7266.4/40
A012 A016 Q003 Q004
M M
O004 O003
BATTERY N009 N008 Je002 Je001 Je003 ??? H005 H007 I105 G005

Fig. 1149
l P008 - Auxiliary air conditioning condenser fan
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 432
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Bc001 Air conditioning com- 40-1365
pressor fuse (10A)
Bc011 Turn indicator lights 40-1365
fuse (key-on power)
(15A)
Bc016 Relay fuse (key-on 40-1365
power) (3A)
Bc023 Fan/compressor 40-1365
fuse (30 A)
Bc025 Protection fuse 40-1365
(40A)
Bc026 MK3 relay fuse 30A 40-1365
Bc031 Ventilation/heating 40-1365
fuse (20A)

40-697
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Be003 Fuse 3 in fuse box F 40-1301
(30A - Climate con-
trol)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C013 Earthing point 40-1365
C023 Grounding point 40-1301
D010 Wiring connector for 40-1331
engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D012 Wiring connector for 40-1311
roof wiring loom
D012 Wiring connector for 40-1301
cab power wiring
loom
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1331
power wiring loom
D028 Wiring connector for 40-1308
roof wiring loom
D028 Wiring connector for 40-1301
air conditioner heat
exchanger fan wiring
loom
D029 Wiring connector for 40-1311
roof wiring loom
D029 Wiring connector for 40-1301
cab power wiring
loom
D029 Connection between 40-1301
cab power supply
wiring and HV roof
wiring
D030 Wiring connector for 40-1311
central cab wiring
loom
D030 Wiring connector for 40-1331
cab power wiring
loom
D031 Wiring connector for 40-1311
central wiring loom
D031 Wiring connector for 40-1331
cab power wiring
loom

40-698
Wiring diagrams
Table 433
System Code P/N Description Characteristics/ Position Wiring loom
notes
D032 Wiring connector for [LNK] 40-1311
roof wiring loom
D032 Wiring connector for [LNK] 40-1301
cab power wiring
loom
D033 Wiring connector to [LNK] 40-1301
wiring loom
D033 Wiring connector for [LNK] 40-1301
roof
D034 Wiring connector to [LNK] 40-1301
wiring loom
D034 Wiring connector for [LNK] 40-1301
roof
D039 Wiring connector for [LNK] 40-1295
central cab wiring
loom
D039 Wiring connector for [LNK] 40-1331
power wiring loom
D040 Wiring connector for [LNK] 40-1295
central wiring loom
D040 Wiring connector for [LNK] 40-1331
power wiring loom
G003 AC LED [LNK] 40-1301
H005 4-speed fan control [LNK] 40-1301
H007 Mechanical thermo- [LNK] 40-1301
stat
I061 0.015.0485.4 Starter switch 40-1365
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

I105 Air conditioning [LNK] 40-1301

switch
J001 Air conditioner heat [LNK] 40-1308
exchanger fan con-
trol relay
J002 Auxiliary air condi- [LNK] 40-1308
tioner heat exchang-
er fan control relay
Jc003 Key-on power relay [LNK] 40-1365
for fuses F11-12-13
Jc006 Fan relay [LNK] 40-1365
Jc008 Fan/compressor re- [LNK] 40-1365
lay (key-on power)
Je001 Max fan speed relay [LNK] 40-1301
Je002 Compressor start [LNK] 40-1301
relay
Je003 Third fan speed re- [LNK] 40-1301
lay
K017 Air conditioning [LNK] 40-1308
pressure switch
N008 RH electric fan [LNK] 40-1301

40-699
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
N009 LH electric fan [LNK] 40-1301
N016 Air conditioning [LNK] 40-1324
compressor
N017 Air conditioning [LNK] 40-1327
compressor
O003 LH resistor [LNK] 40-1301
O004 RH resistor [LNK] 40-1301
P007 Air conditioner heat [LNK] 40-1308
exchanger fan
P008 Auxiliary conditioner [LNK] 40-1308
heat exchanger fan
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

40-700
Wiring diagrams
Table 434
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q004 2.7659.351.0 Battery master 40-1330
switch

40.3.23 - S004 - Starting and preheating, cab

M002 M003

CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V
I028 H013 H014

WATER TEMPERATURE

WATER TEMPERATURE
I035 Ja007 E003

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-
50 15

+5V 24
C007 C009

HOLD

+15
+15
-31

-31

50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 1 2 4 1 2 4 1 2

0.018.3567.4/60

Ba018 Ba024
Ba017
7,5 A

40 A
10A

D040 4 5 1 14 9 11 12
D010 D004 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5

B001
60A

0.016.2001.4/10*
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002
125A

C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020
J006a
J006b

J004*
J003

K026* K025*
Q004 Q003 A016
04215655

Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t

0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1150
l A001 - +30 Battery
l A002 - Preheating device
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Ba017 - Instrument panel fuse (key-on power) (10A)
l Ba018 - Engine ECU fuse (key-on power) (7.5A)
l Ba024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C007 - Earthing point
l C009 - Earthing point
l D004 - Wiring connector for rear wiring loom
l D004 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D014 - Wiring connector for rear wiring loom
l D014 - Wiring connector for engine wiring loom

40-701
 Wiring diagrams
M002 M003

CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V
I028 H013 H014

WATER TEMPERATURE

WATER TEMPERATURE
I035 Ja007 E003

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-
50 15

+5V 24
C007 C009

HOLD

+15
+15
-31

-31
50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 1 2 4 1 2 4 1 2
0.018.3567.4/60

Ba018 Ba024
Ba017
7,5 A

40 A
10A

D040 4 5 1 14 9 11 12
D010 D004 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5

B001
60A

0.016.2001.4/10*
0.016.2000.4/20

0.015.7023.4/50
0.014.9195.4/20

B002
125A

C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020
J006a
J006b

J004*
J003

K026* K025*
Q004 Q003 A016

04215655
Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t

0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1150
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l E003 - Instrument panel
l H013 - Mechanical hand throttle
l H014 - Accelerator pedal
l I028 - Engine memory switch
l I035 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay
l Ja007 - Starter relay
l K020 - Engine oil pressure switch
l K021 - Engine temperature sensor
l K025 - Engine oil pressure switch
l K026 - Engine temperature sensor
l K030 - Engine coolant temperature sensor
l K032 - Turbine air temperature/pressure sensor
l K035 - Camshaft speed sensor
l K036 - Fuel temperature sensor
l M002 - Engine ECU
l M003 - Engine ECU
l N005 - Starter motor “+30”
l N013 - Actuator
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

Table 435
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

40-702
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
A002 04258670 Preheating device 40-1290
A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B002 0.900.0783.1 Preheat fuse 125A 40-1290
Ba017 Instrument panel 40-1331
fuse (key-on power)
(10A)
Ba018 Engine ECU fuse 40-1331
(key-on power)
(7.5A)
Ba024 Starter fuse (40A) 40-1331
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C007 Earthing point 40-1331
C009 Earthing point 40-1331
D004 Wiring connector for 40-1331
rear wiring loom
D004 Wiring connector for 40-1306
central wiring loom
D010 Wiring connector for 40-1331
engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D014 Wiring connector for 40-1425
rear wiring loom
D014 Wiring connector for 40-1306
engine wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1331
power wiring loom
E003 2.8339.269.0/50 Instrument panel 40-1331
H013 04429390/10 Mechanical hand 40-1331
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H014 Accelerator pedal 40-1331

I028 Engine memory 40-1331
switch

40-703
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
I035 0.015.0485.4 Starter switch 40-1331
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

J003 Preheating relay 40-1324

J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

J006b Preheating relay J006b

40-1290

Ja007 Starter relay 40-1331

K020 Engine oil pressure 40-1324
switch
K021 Engine temperature 40-1324
sensor
Table 436
System Code P/N Description Characteristics/ Position Wiring loom
notes
K025 Engine oil pressure 40-1327
switch
K026 Engine temperature 40-1327
sensor
K030 Engine coolant tem- 40-1425
perature sensor
K032 Turbine air tempera- 40-1425
ture/pressure sensor
K035 Camshaft speed 40-1425
sensor
K036 Fuel temperature 40-1425
sensor
M002 Engine control unit 40-1331
M003 Engine control unit 40-1331
N005 Starter motor “+30” 40-1329
N013 Actuator 40-1425
Q001 2.7659.351.0 Battery master 40-1330
switch

40-704
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q002 2.7659.351.0 Battery master 40-1330
switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40.3.24 - S004 - Starting and preheating, cab - USA

M007 M008
CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V

I044 H017 H018

WATER TEMPERATURE

WATER TEMPERATURE

I045 Jb007 E005

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND

30
-31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-

50 15
+5V 24

C010 C012
HOLD

+15
+15
-31

-31

50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 1 2 4 1 2 4 1 2

0.018.4081.4/30

Bb017 Bb018 Bb024

7,5 A

40 A
10A

D040 4 5 1 14 9 11 12
D010 D004 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5

B001
60A

0.016.2001.4/10*
0.014.9195.4/20

0.016.2000.4/20

0.015.7023.4/50

B002
125A

C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020
J006a
J006b

J004*
J003

K026* K025*
Q004 Q003 A016
04215655

Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t
0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1151
l A001 - +30 Battery
l A002 - Preheating device

40-705
 Wiring diagrams
M007 M008

CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V
I044 H017 H018

WATER TEMPERATURE

WATER TEMPERATURE
I045 Jb007 E005

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-
50 15

+5V 24
C010 C012

HOLD

+15
+15
-31

-31
50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 1 2 4 1 2 4 1 2
0.018.4081.4/30

Bb017 Bb018 Bb024

7,5 A

40 A
10A

D040 4 5 1 14 9 11 12
D010 D004 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5

B001
60A

0.016.2001.4/10*
0.014.9195.4/20

0.016.2000.4/20

0.015.7023.4/50
125A B002

C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020
J006a
J006b

J004*
J003

K026* K025*
Q004 Q003 A016

04215655
Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t
0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1151
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bb017 - Instrument panel fuse (key-on power) (10A)
l Bb018 - Engine ECU fuse (key-on power) (7.5A)
l Bb024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C010 - Earthing point
l C012 - Earthing point
l D004 - Wiring connector for rear wiring loom
l D004 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D014 - Wiring connector for rear wiring loom
l D014 - Wiring connector for engine wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l E005 - Instrument panel
l H018 - Mechanical hand throttle
l H017 - Accelerator pedal
l I044 - Engine memory switch
l I045 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay
l Jb007 - Starter relay
l K020 - Engine oil pressure switch
l K021 - Engine temperature sensor
l K025 - Engine oil pressure switch
l K026 - Engine temperature sensor
l K030 - Engine coolant temperature sensor
l K032 - Turbine air temperature/pressure sensor

40-706
Wiring diagrams
M007 M008

CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V
I044 H017 H018

WATER TEMPERATURE

WATER TEMPERATURE
I045 Jb007 E005

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-
50 15

+5V 24
C010 C012

HOLD

+15
+15
-31

-31
50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 1 2 4 1 2 4 1 2
0.018.4081.4/30

Bb017 Bb018 Bb024

7,5 A

40 A
10A

D040 4 5 1 14 9 11 12
D010 D004 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5

B001
60A

0.016.2001.4/10*
0.014.9195.4/20

0.016.2000.4/20

0.015.7023.4/50
125A B002

C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020
J006a
J006b

J004*
J003

K026* K025*
Q004 Q003 A016

04215655
Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t
0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1151
l K035 - Camshaft speed sensor
l K036 - Fuel temperature sensor
l M007 - Engine ECU
l M008 - Engine ECU
l N005 - Starter motor “+30”
l N013 - Actuator
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 437
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Bb017 Instrument panel 40-1347
fuse (key-on power)
(10A)
Bb018 Engine ECU fuse 40-1347
(key-on power)
(7.5A)
Bb024 Starter fuse (40A) 40-1347

40-707
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C010 Grounding point 40-1347
C012 Earthing point 40-1347
D004 Wiring connector for 40-1306
rear wiring loom
D004 Wiring connector for 40-1347
central wiring loom
D010 Wiring connector for 40-1324
engine wiring loom
D010 Wiring connector for 40-1347
central wiring loom
D014 Wiring connector for 40-1425
rear wiring loom
D014 Wiring connector for 40-1306
engine wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1331
power wiring loom
E005 2.8339.269.0/50 Instrument panel 40-1331
H017 04429390/10 Mechanical hand 40-1347
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H018 Accelerator pedal 40-1347

I044 Engine memory 40-1347
switch
I045 Starter switch 40-1347
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

J003 0.015.0485.4 Preheating relay 40-1324

J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

J006b Preheating relay J006b

40-1290

Jb007 Starter relay 40-1347

K020 Engine oil pressure 40-1324
switch
K021 Engine temperature 40-1324
sensor

40-708
Wiring diagrams
Table 438
System Code P/N Description Characteristics/ Position Wiring loom
notes
K025 Engine oil pressure 40-1327
switch
K026 Engine temperature 40-1327
sensor
K030 Engine coolant tem- 40-1425
perature sensor
K032 Turbine air tempera- 40-1425
ture/pressure sensor
K035 Camshaft speed 40-1425
sensor
K036 Fuel temperature 40-1425
sensor
M002 Engine control unit 40-1331
M003 Engine control unit 40-1331
N005 Starter motor “+30” 40-1329
N013 Actuator 40-1425
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-709
 Wiring diagrams
40.3.25 - S004 - Engine and preheat, cab version with electronic lift (AGROFARM 430 ->
ZKDW430200TD25001, AGROFARM 430 -> ZKDW550200TD30001)
M009 M010

CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V
I058 H021 H022

WATER TEMPERATURE

WATER TEMPERATURE
I061 Jc007 E007

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-
50 15

+5V 24
C013 C015

HOLD

+15
+15
-31

-31
50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 1 2 4 1 2 4 1 2
0.018.4537.4/40

Bc017 Bc018 Bc024

7,5 A

40 A
10A

D010 D022 D038

D040 4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5 12 11
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5 12 11

B001
60A

0.016.2001.4/10*
0.016.2000.4/20

0.018.5230.4/10
0.014.9195.4/20

0.018.4891.4
B002
125A

C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1 1 2

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020 I067

J004*
J003
J006a
J006b

K026* K025*
Q004 Q003

04215655
A016
Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t

0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1152
l A001 - +30 Battery
l A002 - Preheating device
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bc017 - Instrument panel fuse (key-on power) (10A)
l Bc018 - Engine ECU fuse (key-on power) (7.5A)
l Bc024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C013 - Earthing point
l C015 - Earthing point
l D010 - Wiring connector for front wiring loom
l D010 - Wiring connector for central wiring loom
l D014 - Wiring connector for rear wiring loom
l D014 - Wiring connector for engine wiring loom
l D022 - Wiring connector for central wiring loom
l D022 - Wiring connector for rear wiring loom
l D038 - Wiring connector for RH side console wiring loom
l D038 - Wiring connector for central wiring loom and electronic lift
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l E007 - Instrument panel
l H021 - Mechanical hand throttle
l H022 - Accelerator pedal
l I058 - Engine memory switch
l I061 - Ignition switch
l I067 - Engine memory switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay

40-710
Wiring diagrams
M009 M010

CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V
I058 H021 H022

WATER TEMPERATURE

WATER TEMPERATURE
I061 Jc007 E007

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-
50 15

+5V 24
C013 C015

HOLD

+15
+15
-31

-31
50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 1 2 4 1 2 4 1 2
0.018.4537.4/40

Bc017 Bc018 Bc024

7,5 A

40 A
10A

D010 D022 D038

D040 4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5 12 11
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5 12 11

B001
60A

0.016.2001.4/10*
0.016.2000.4/20

0.018.5230.4/10
0.014.9195.4/20

0.018.4891.4
125A B002

C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1 1 2

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020 I067

J004*
J003
J006a
J006b

K026* K025*
Q004 Q003

04215655
A016
Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t

0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1152
l J006b - Preheating relay
l Jc007 - Starter relay
l K020 - Engine oil pressure switch
l K021 - Engine temperature sensor
l K025 - Engine oil pressure switch
l K026 - Engine temperature sensor
l K030 - Engine coolant temperature sensor
l K032 - Turbine air temperature/pressure sensor
l K035 - Camshaft speed sensor
l K036 - Fuel temperature sensor
l M009 - Engine ECU
l M010 - Engine ECU
l N005 - Starter motor “+30”
l N013 - Actuator
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 439
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290

40-711
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Bc017 Instrument panel 40-1365
fuse (key-on power)
(10A)
Bc018 Engine ECU fuse 40-1365
(key-on power)
(7.5A)
Bc024 Starter fuse (40A) 40-1365
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C013 Earthing point 40-1365
C015 Grounding point 40-1365
D010 Wiring connector for 40-1365
front wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D014 Wiring connector for 40-1425
rear wiring loom
D014 Wiring connector for 40-1385
engine wiring loom
D022 Wiring connector for 40-1385
central wiring loom
D022 Wiring connector for 40-1365
rear wiring loom
D038 Wiring connector for 40-1365
RH side console wir-
ing loom
D038 Wiring connector for 40-1386
central wiring loom
and electronic lift
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1365
power wiring loom
E007 2.8339.269.0/50 Instrument panel 40-1365
H021 04429390/10 Mechanical hand 40-1365
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H022 Accelerator pedal 40-1365

I058 Engine memory 40-1365
switch
I061 0.015.0485.4 Starter switch 40-1365
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

I067 2.7659.362.0 Engine memory 40-1386

switch

40-712
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
J003 Preheating relay 40-1324
J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

J006b Preheating relay J006b

40-1290

Jc007 Starter relay 40-1365

K020 Engine oil pressure 40-1324
switch
K021 Engine temperature 40-1324
sensor
Table 440
System Code P/N Description Characteristics/ Position Wiring loom
notes
K025 Engine oil pressure 40-1327
switch
K026 Engine temperature 40-1327
sensor
K030 Engine coolant tem- 40-1425
perature sensor
K032 Turbine air tempera- 40-1425
ture/pressure sensor
K035 Camshaft speed 40-1425
sensor
K036 Fuel temperature 40-1425
sensor
M009 Engine control unit 40-1365
M010 Engine control unit 40-1365
N005 Starter motor “+30” 40-1329
N013 Actuator 40-1425
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

40-713
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q003 2.7659.351.0 Battery master 40-1330
switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40.3.26 - S004 - Starting and preheating, platform (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKDW390200TD25001,
AGROFARM 420 -> ZKDW510200TD30001)
M013 M014
CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V

H025 H026
WATER TEMPERATURE

WATER TEMPERATURE

I087 Jd007 E009

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND

30 -31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-

50 15
+5V 24
C017 C013

HOLD

+15
+15
-31

-31

50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 4 1 2 4 1 2

0.018.7845.4/20

Bd017 Bd018 Bd024

7,5 A

40 A
10A

11 10 D036

11 10

D040 4 5 1 14 9 11 12
D010 D004 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5
1 2
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5

B001

I081
60A

0.016.2001.4/10*
0.016.2000.4/20
0.014.9195.4/20

0.015.7023.4/50

B002
125A

C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020
J006a
J006b

J004*
J003

K026* K025*
Q004 Q003 A016
04215655

Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t
0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1153
l A001 - +30 Battery
l A002 - Preheating device
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bd017 - Instrument panel fuse (key-on power) (10A)
l Bd018 - Engine ECU fuse (key-on power) (7.5A)

40-714
Wiring diagrams
M013 M014

CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V
H025 H026

WATER TEMPERATURE

WATER TEMPERATURE
I087 Jd007 E009

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-
50 15

+5V 24
C017 C013

HOLD

+15
+15
-31

-31
50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 4 1 2 4 1 2
0.018.7845.4/20

Bd017 Bd018 Bd024

7,5 A

40 A
10A

11 10 D036

11 10

D040 4 5 1 14 9 11 12
D010 D004 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5
1 2
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5

B001

I081
60A

0.016.2001.4/10*
0.016.2000.4/20
0.014.9195.4/20

0.015.7023.4/50
B002

125A
C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020
J006a
J006b

J004*
J003

K026* K025*
Q004 Q003 A016

04215655
Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t
0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1153
l Bd024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C017 - Earthing point
l D004 - Wiring connector for rear wiring loom
l D004 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D014 - Wiring connector for rear wiring loom
l D014 - Wiring connector for engine wiring loom
l D036 - Wiring connector
l D036 - Wiring connector for lower wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l E009 - Instrument panel
l H025 - Mechanical hand throttle
l H026 - Accelerator pedal
l I081 - Engine memory switch
l I087 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay
l Jd007 - Starter relay
l K020 - Engine oil pressure switch
l K021 - Engine temperature sensor
l K025 - Engine oil pressure switch
l K026 - Engine temperature sensor
l K030 - Engine coolant temperature sensor
l K032 - Turbine air temperature/pressure sensor
l K035 - Camshaft speed sensor
l K036 - Fuel temperature sensor
l M013 - Engine ECU
l M014 - Engine ECU
l N005 - Starter motor “+30”
l N013 - Actuator
l Q001 - Battery master switch

40-715
 Wiring diagrams
M013 M014

CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V
H025 H026

WATER TEMPERATURE

WATER TEMPERATURE
I087 Jd007 E009

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-
50 15

+5V 24
C017 C013

HOLD

+15
+15
-31

-31
50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 4 1 2 4 1 2
0.018.7845.4/20

Bd017 Bd018 Bd024

7,5 A

40 A
10A

11 10 D036

11 10

D040 4 5 1 14 9 11 12
D010 D004 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5
1 2
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5

B001

I081
60A

0.016.2001.4/10*
0.016.2000.4/20
0.014.9195.4/20

0.015.7023.4/50
B002

125A
C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020
J006a
J006b

J004*
J003

K026* K025*
Q004 Q003 A016

04215655
Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t
0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1153
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

Table 441
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290
Bd017 Instrument panel 40-1392
fuse (key-on power)
(10A)
Bd018 Engine ECU fuse 40-1392
(key-on power)
(7.5A)
Bd024 Starter fuse (40A) 40-1392
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C017 Earthing point 40-1392
D004 Wiring connector for 40-1392
rear wiring loom
D004 Wiring connector for 40-1306
central wiring loom

40-716
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
D010 Wiring connector for 40-1392
engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D014 Wiring connector for 40-1425
rear wiring loom
D014 Wiring connector for 40-1306
engine wiring loom
D036 Wiring connector 40-1392
D036 Wiring connector for 40-1392
switch wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1392
power wiring loom
E009 2.8339.269.0/50 Instrument panel 40-1392
H025 04429390/10 Mechanical hand 40-1392
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H026 Accelerator pedal 40-1392

I081 Engine memory 40-1392
switch
I087 0.015.0485.4 Starter switch 40-1392
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

J003 Preheating relay 40-1324

J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

J006b Preheating relay J006b

40-1290

Jd007 Starter relay 40-1392

K020 Engine oil pressure 40-1324
switch
K021 Engine temperature 40-1324
sensor

40-717
 Wiring diagrams
Table 442
System Code P/N Description Characteristics/ Position Wiring loom
notes
K025 Engine oil pressure 40-1327
switch
K026 Engine temperature 40-1327
sensor
K030 Engine coolant tem- 40-1425
perature sensor
K032 Turbine air tempera- 40-1425
ture/pressure sensor
K035 Camshaft speed 40-1425
sensor
K036 Fuel temperature 40-1425
sensor
M013 Engine control unit 40-1392
M014 Engine control unit 40-1392
N005 Starter motor “+30” 40-1329
N013 Actuator 40-1425
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-718
Wiring diagrams
40.3.27 - S004 - Starting and preheating, platform - USA (AGROFARM 410 -> ZKD-
W350200TD25001, AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 ->
ZKDW390200TD25001, AGROFARM 420 -> ZKDW510200TD30001)
M017 M018

CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V
H029 H030

WATER TEMPERATURE

WATER TEMPERATURE
I102 Jh007 E011

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-
50 15

+5V 24
C020 C022

HOLD

+15
+15
-31

-31
50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 4 1 2 4 1 2
0.018.8008.4

Bh017 Bh018 Bh024

7,5 A

40 A
10A

11 10 D037

11 10

D040 4 5 1 14 9 11 12
D010 D004 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5
1 2
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5

B001

I095
60A

0.016.2001.4/10*
0.014.9195.4/20

0.016.2000.4/20

0.015.7023.4/50
B002
125A

C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020
J006a
J006b
J004*
J003

K026* K025*
Q004 Q003 A016

04215655
Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t
0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1154
l A001 - +30 Battery
l A002 - Preheating device
l A013 - Battery +30
l A014 - Battery positive terminal
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B002 - 125A preheat fuse
l Bh017 - Instrument panel fuse (key-on power) (10A)
l Bh018 - Engine ECU fuse (key-on power) (7.5A)
l Bh024 - Starter fuse (40A)
l C004 - Earthing point
l C005 - Earthing point
l C020 - Earthing point
l C022 - Earthing point
l D004 - Wiring connector for rear wiring loom
l D004 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D014 - Wiring connector for rear wiring loom
l D014 - Wiring connector for engine wiring loom
l D037 - Wiring connector
l D037 - Wiring connector for lower wiring loom
l D040 - Wiring connector for central wiring loom
l E011 - Instrument panel
l H029 - Mechanical hand throttle
l H030 - Accelerator pedal
l I095 - Engine memory switch
l I102 - Ignition switch
l J003 - Preheating relay
l J004 - Preheating relay
l J006a - Preheating relay
l J006b - Preheating relay

40-719
 Wiring diagrams
M017 M018

CHARGE AIR PRESS.TEMPER.

CHARGE AIR PRESSURE GND

CHARGE AIR PRESSURE SIGNAL
CHARGE AIR PRESSURE +5V
H029 H030

WATER TEMPERATURE

WATER TEMPERATURE
I102 Jh007 E011

SIGNAL PEDAL GAS

HAND GAS SIGNAL

START CONSENT
GND COM 24/20
OIL ENGINE PRESS.

GND SCREEN

H.D.COMAND
30

-31 ELECTR.

-31 ELECTR.
FUEL TEMP
ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR

ATTUATOR
PRE-HEATING

PRE-HEATING

GND COM
PICK-UP+

PICK-UP-
50 15

+5V 24
C020 C022

HOLD

+15
+15
-31

-31
50 15 30 87 86 85 30 5-13 3-8 3-14 3-6 5-15 4 25 24 23 19 18 17 15 14 13 12 16 9 8 5 3 3 2 1 25 24 23 20 18 17 6 14 4 1 2 4 1 2
0.018.8008.4

Bh017 Bh018 Bh024

7,5 A

40 A
10A

11 10 D037

11 10

D040 4 5 1 14 9 11 12
D010 D004 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5
1 2
0.015.1983.4/10

4 5 1 14 9 11 12 A-A4 B-C5 A-C8 A-C7 A-C3 A-C2 A-C1 A-B7 A-B6 A-B5 A-B4 B-C4 A-B1 A-A5

B001

I095
60A

0.016.2001.4/10*
0.014.9195.4/20

0.016.2000.4/20

0.015.7023.4/50
B002

125A
C005
C004*
D014 4 25 24 23 19 18 17 15 14 13 12 9 8 5
0.017.8922.4/10*
0.017.9016.4/10

A001 A002 4 3 1 2 A006 2 1 1

A018* 4 25 24 23 19 18 17 15 14 13 12 9 8 5

K021 K020
J006a
J006b
J004*
J003

K026* K025*
Q004 Q003 A016

04215655
Q002* Q001* A015* A013

A014
2 3 4 1 4 5 3 2 1 2 1 2 1 2 1

N005 t t
0.017.0474.4
K032 N013 K035 K030 K036
GND +30
M
BATTERY

Fig. 1154
l Jh007 - Starter relay
l K020 - Engine oil pressure switch
l K021 - Engine temperature sensor
l K025 - Engine oil pressure switch
l K026 - Engine temperature sensor
l K030 - Engine coolant temperature sensor
l K032 - Turbine air temperature/pressure sensor
l K035 - Camshaft speed sensor
l K036 - Fuel temperature sensor
l M017 - Engine ECU
l M018 - Engine ECU
l N005 - Starter motor “+30”
l N013 - Actuator
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 443
System Code P/N Description Characteristics/ Position Wiring loom
notes
A001 Battery +30 40-1290

A001

A002 04258670 Preheating device 40-1290

A013 Battery +30 40-1295
A014 Battery positive ter- 40-1329
minal
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B002 Preheat fuse 125A 40-1290

40-720
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Bh017 Instrument panel 40-1410
fuse (key-on power)
(10A)
Bh018 Engine ECU fuse 40-1410
(key-on power)
(7.5A)
Bh024 Starter fuse (40A) 40-1410
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C020 Grounding point 40-1410
C022 Grounding point 40-1410
D004 Wiring connector for 40-1410
rear wiring loom
D004 Wiring connector for 40-1306
central wiring loom
D010 Wiring connector for 40-1410
engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D014 Wiring connector for 40-1425
rear wiring loom
D014 Wiring connector for 40-1306
engine wiring loom
D037 Wiring connector 40-1410
D037 Wiring connector for 40-1410
switch wiring loom
D040 Wiring connector for 40-1295
central wiring loom
E011 2.8339.269.0/50 Instrument panel 40-1410
H029 04429390/10 Mechanical hand 40-1410
throttle
4 5 6

1 2 3

1
2 output signals
U [%]
B Signal 1 = Signal 2
U 90 U B

U 10 U B

0°
-45° +45°

H030 Accelerator pedal 40-1410

I095 Engine memory 40-1410
switch
I102 0.015.0485.4 Starter switch 40-1410
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

J003 Preheating relay 40-1324

J004 Preheating relay 40-1327
J006a Preheating relay J006a
40-1290

40-721
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
J006b Preheating relay J006b
40-1290

Jh007 Starter relay 40-1410

K020 Engine oil pressure 40-1324
switch
K021 Engine temperature 40-1324
sensor

Table 444
System Code P/N Description Characteristics/ Position Wiring loom
notes
K025 Engine oil pressure 40-1327
switch
K026 Engine temperature 40-1327
sensor
K030 Engine coolant tem- 40-1425
perature sensor
K032 Turbine air tempera- 40-1425
ture/pressure sensor
K035 Camshaft speed 40-1425
sensor
K036 Fuel temperature 40-1425
sensor
M017 Engine control unit 40-1410
M018 Engine control unit 40-1410
N005 Starter motor “+30” 40-1329
N013 Actuator 40-1425
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

40-722
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q004 2.7659.351.0 Battery master 40-1330
switch

40.3.28 - S005 - PTO, cab version

M001 M005

I023 I024 I022 E003 I036 I037 I032

I035

LED F PTO FORW

FRONT PTO LED

FRONT PTO SW.

FRONT PTO LED

D+ GENERATOR

D+ GENERATOR

D+ GENERATOR
EXT. PTO COM.

FRONT PTO EV
LEDhB (LAMP)

EV REAR PTO
30

ECONOMIC PTO
REAR PTO

SYNCRO PTO
EV FORW

REAR PTO
50 15
C009 C008 C007

PTO 1000
PTO 540
PUEN
+15

+15
-31

-31

+15
-31

-31

W
50 15 30 1 3 2 1 3 2 6 1 17 2 8 14 7 12 15 12 1 11 2 7 14 6 1 2 3-20 5-16 3-13 5-13 3-8 3-14 3-24 3-9 3-11 3-10 5-24 1 2 1 2 1 2
0.018.3567.4/60

Ba017
10A

D001
3 3
1 1

D004 D010
D040 B-C3 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B-C3 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B001

0.016.2001.4/10*
60A

0.015.7023.4/50

1 2 D082 A005 A004 A003 A007 0.016.2000.4/20

1 2 1 2 1 2 A010* A009* A008* A017*

C005 1 2

C004*
0.012.2756.3
0.017.8922.4/10*
0.015.1983.4/10

L008 I008 I009

0.017.9016.4/10

1 2

A016 Q003 Q004

A013 A015* Q001* Q002*

L001

BATTERY

Fig. 1155
l A003 - Alternator “B+”
l A004 - Alternator “D+”
l A005 - Alternator “W”
l A007 - Battery positive terminal
l A008 - Alternator “B+”
l A009 - Alternator “D+”
l A010 - Alternator “W”
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A017 - Battery positive terminal
l B001 - 60A fuse
l Ba017 - Instrument panel fuse (key-on power) (10A)
l C004 - Earthing point
l C005 - Earthing point
l C007 - Earthing point
l C008 - Earthing point
l C009 - Earthing point
l D001 - Wiring connector
l D001 - Wiring connector for lower wiring loom

40-723
 Wiring diagrams
M001 M005

I023 I024 I022 E003 I036 I037 I032

I035

LED F PTO FORW

FRONT PTO LED

FRONT PTO SW.

FRONT PTO LED

D+ GENERATOR

D+ GENERATOR

D+ GENERATOR
EXT. PTO COM.

FRONT PTO EV
LEDhB (LAMP)

EV REAR PTO
30

ECONOMIC PTO
REAR PTO

SYNCRO PTO
EV FORW

REAR PTO
50 15
C009 C008 C007

PTO 1000
PTO 540
PUEN
+15

+15
-31

-31

+15
-31

-31

W
50 15 30 1 3 2 1 3 2 6 1 17 2 8 14 7 12 15 12 1 11 2 7 14 6 1 2 3-20 5-16 3-13 5-13 3-8 3-14 3-24 3-9 3-11 3-10 5-24 1 2 1 2 1 2

0.018.3567.4/60

Ba017
10A

D001
3 3
1 1

D004 D010
D040 B-C3 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B-C3 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B001

0.016.2001.4/10*
60A

0.015.7023.4/50

0.016.2000.4/20
1 2 D082 A005 A004 A003 A007
1 2 1 2 1 2 A010* A009* A008* A017*

C005 1 2

C004*

0.012.2756.3
0.017.8922.4/10*
0.015.1983.4/10

L008 I008 I009

0.017.9016.4/10

1 2

A016 Q003 Q004

A013 A015* Q001* Q002*

L001

BATTERY

Fig. 1155
l D004 - Wiring connector for rear wiring loom
l D004 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l D082 - Wiring connector for front PTO control solenoid valve
l D082 - Wiring connector for engine wiring loom
l E003 - Instrument panel
l I008 - PTO engage switch SYNCRO
l I009 - PTO engage switch ECO
l I022 - Front PTO switch
l I023 - LH external PTO control
l I024 - RH external PTO control
l I032 - Rear PTO switch
l I035 - Ignition switch
l I036 - 1,000 rpm PTO switch
l I037 - 540 rpm PTO switch
l L001 - Front PTO solenoid valve
l L008 - Rear PTO control solenoid valve
l M001 - ECU Rear PTO
l M005 - ECU Front PTO
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 445
System Code P/N Description Characteristics/ Position Wiring loom
notes
A003 01182961 Alternator “B+” 40-1324
A004 01182961 Alternator “D+” 40-1324
A005 01182961 Alternator “W” 40-1324

40-724
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
A007 Battery positive ter- 40-1324
minal
A008 01182961 Alternator “B+” 40-1327
A009 01182961 Alternator “D+” 40-1327
A010 01182961 Alternator “W” 40-1327
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A017 Battery positive ter- 40-1327
minal
B001 0.900.0783.1 60A fuse 40-1295
Ba017 Instrument panel 40-1331
fuse (key-on power)
(10A)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C007 Earthing point 40-1331
C008 Earthing point 40-1331
C009 Earthing point 40-1331
D001 Wiring connector 40-1331
D001 Wiring connector for 40-1331
switch wiring loom
D004 Wiring connector for 40-1331
rear wiring loom
D004 Wiring connector for 40-1306
central wiring loom
D010 Wiring connector for 40-1331
engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1331
power wiring loom
D082 Wiring connector for 40-1324
front PTO control so-
lenoid valve
D082 Wiring connector for 40-1327
front PTO control so-
lenoid valve
D082 Wiring connector for 40-1281
engine wiring loom
E003 2.8339.269.0/50 Instrument panel 40-1331
I008 2.7659.096.0/10 PTO engage switch 40-1306
CB A

SYNCRO
Between Pin 1 and
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact

40-725
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
I009 2.7659.096.0/10 PTO engage switch 40-1306

CB A
ECO
Between Pin 1 and
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
I022 2.7659.177.0/20 Front PTO switch 40-1331
Resistance between
Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I023 LH external PTO 40-1331
control
I024 RH external PTO 40-1331
control
I032 2.7659.350.0 Rear PTO switch 1 40-1331
2
3

2 220 ohm
1W
1 270 ohm

3 1W

I035 0.015.0485.4 Starter switch 40-1331

83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

40-726
Wiring diagrams
Table 446
System Code P/N Description Characteristics/ Position Wiring loom
notes
I036 2.7659.097.0 1,000 rpm PTO 1 40-1331
switch
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I037 2.7659.097.0 540 rpm PTO switch 1 40-1331
Between Pin 1 and
Pin 2: normally 4

closed (NC) switch

Between Pin 3 and
Pin 4: normally open
(NO) switch
L001 Front PTO control 40-1281
solenoid valve
L008 Rear PTO control 40-1306
solenoid valve
M001 2.8519.115.0/20 ECU Rear PTO 40-1331
M005 2.8519.115.0/20 ECU Front PTO 40-1331
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

40-727
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q004 2.7659.351.0 Battery master 40-1330
switch

40.3.29 - S005 - PTO, cab version - USA

M006
I040 I039 E005 I046 I047

SENS. ENABLE (PUEN)

I045

SEGNALE SENS.USA
FRONT PTO LED
FRONT PTO SW.

FRONT PTO LED

D+ GENERATOR

D+ GENERATOR
FRONT PTO EV
REAR PTO LED
REAR PTO SW.

REAR PTO LED

EV REAR PTO
30

ECONOMIC PTO
SYNCRO PTO
50 15
C010

PTO 1000
PTO 540
+15

-31

+15
-31

-31

W
50 15 30 1 2 1 2 6 1 17 2 9 14 7 12 15 11 18 3-20 5-16 3-13 5-13 3-8 3-14 3-24 3-9 3-11 3-10 5-24 1 2 1 2
0.018.4081.4/30

D043
Bb017 3 3
2 2
10A

D004 D010
D040 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

C011 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B001
60A

0.015.7023.4/50

1 2 D082
1 2 3
D018 A005 A004
1 2 1 2 1 2 A010* A009*
1 2
C005 1 2 3
0.012.2756.3
0.017.8922.4/10*

0.015.4257.4/10
0.015.1983.4/10

L008 I008 I009

0.017.9016.4/10

1 2

A016 Q003 Q004

A013 A015* Q001* Q002* 1 2 3

L001

K008

BATTERY

Fig. 1156
l A003 - Alternator “B+”
l A004 - Alternator “D+”
l A005 - Alternator “W”
l A007 - Battery positive terminal
l A008 - Alternator “B+”
l A009 - Alternator “D+”
l A010 - Alternator “W”
l A013 - Battery +30

40-728
Wiring diagrams
M006
I040 I039 E005 I046 I047

SENS. ENABLE (PUEN)

I045

SEGNALE SENS.USA
FRONT PTO LED
FRONT PTO SW.

FRONT PTO LED

D+ GENERATOR

D+ GENERATOR
FRONT PTO EV
REAR PTO LED
REAR PTO SW.

REAR PTO LED

EV REAR PTO
30

ECONOMIC PTO
SYNCRO PTO
50 15
C010

PTO 1000
PTO 540
+15

-31

+15
-31

-31

W
50 15 30 1 2 1 2 6 1 17 2 9 14 7 12 15 11 18 3-20 5-16 3-13 5-13 3-8 3-14 3-24 3-9 3-11 3-10 5-24 1 2 1 2

0.018.4081.4/30

D043
Bb017 3 3
2 2
10A

D004 D010
D040 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

C011 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B001
60A

0.015.7023.4/50
1 2 D082
1 2 3
D018 A005 A004
1 2 1 2 1 2 A010* A009*
1 2
C005 1 2 3

0.012.2756.3
0.017.8922.4/10*

0.015.4257.4/10
0.015.1983.4/10

L008 I008 I009

0.017.9016.4/10

1 2

A016 Q003 Q004

A013 A015* Q001* Q002* 1 2 3

L001

K008

BATTERY

Fig. 1156
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A017 - Battery positive terminal
l B001 - 60A fuse
l Bb017 - Instrument panel fuse (key-on power) (10A)
l C004 - Earthing point
l C005 - Earthing point
l C010 - Earthing point
l C011 - Earthing point
l C012 - Earthing point
l D004 - Wiring connector for rear wiring loom
l D004 - Wiring connector for central wiring loom
l D010 - Wiring connector for front wiring loom
l D010 - Wiring connector for central wiring loom
l D018 - Wiring connector for PTO sensor wiring loom (EXPORT USA)
l D018 - Wiring connector for central wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l D043 - Wiring connector
l D043 - Wiring connector for lower wiring loom
l D082 - Wiring connector for front PTO control solenoid valve
l D082 - Wiring connector for engine wiring loom

40-729
 Wiring diagrams
M006
I040 I039 E005 I046 I047

SENS. ENABLE (PUEN)

I045

SEGNALE SENS.USA
FRONT PTO LED
FRONT PTO SW.

FRONT PTO LED

D+ GENERATOR

D+ GENERATOR
FRONT PTO EV
REAR PTO LED
REAR PTO SW.

REAR PTO LED

EV REAR PTO
30

ECONOMIC PTO
SYNCRO PTO
50 15
C010

PTO 1000
PTO 540
+15

-31

+15
-31

-31

W
50 15 30 1 2 1 2 6 1 17 2 9 14 7 12 15 11 18 3-20 5-16 3-13 5-13 3-8 3-14 3-24 3-9 3-11 3-10 5-24 1 2 1 2

0.018.4081.4/30

D043
Bb017 3 3
2 2
10A

D004 D010
D040 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

C011 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B001
60A

0.015.7023.4/50
1 2 D082
1 2 3
D018 A005 A004
1 2 1 2 1 2 A010* A009*
1 2
C005 1 2 3

0.012.2756.3
0.017.8922.4/10*

0.015.4257.4/10
0.015.1983.4/10

L008 I008 I009

0.017.9016.4/10

1 2

A016 Q003 Q004

A013 A015* Q001* Q002* 1 2 3

L001

K008

BATTERY

Fig. 1156
l E005 - Instrument panel
l I008 - PTO engage switch SYNCRO
l I009 - PTO engage switch ECO
l I039 - Front PTO switch
l I040 - Rear PTO switch
l I045 - Ignition switch
l I046 - 1,000 rpm PTO switch
l I047 - 540 rpm PTO switch
l K008 - PTO speed sensor
l L001 - Front PTO solenoid valve
l L008 - Rear PTO control solenoid valve
l M006 - ECU PTO
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

Table 447
System Code P/N Description Characteristics/ Position Wiring loom
notes
A003 01182961 Alternator “B+” 40-1324
A004 01182961 Alternator “D+” 40-1324

40-730
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
A005 01182961 Alternator “W” 40-1324
A007 Battery positive ter- 40-1324
minal
A008 01182961 Alternator “B+” 40-1327
A009 01182961 Alternator “D+” 40-1327
A010 01182961 Alternator “W” 40-1327
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A017 Battery positive ter- 40-1327
minal
B001 0.900.0783.1 60A fuse 40-1295
Bb017 Instrument panel 40-1347
fuse (key-on power)
(10A)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C010 Grounding point 40-1347
C011 Grounding point 40-1347
C012 Earthing point 40-1347
D004 Wiring connector for 40-1347
rear wiring loom
D004 Wiring connector for 40-1306
central wiring loom
D010 Wiring connector for 40-1347
front wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D018 Wiring connector for 40-1306
PTO sensor wiring
loom - (USA EX-
PORT)
D018 Wiring connector for 40-1300
central wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1347
power wiring loom
D043 Wiring connector 40-1347
D043 Wiring connector for 40-1347
switch wiring loom
D082 Wiring connector for 40-1324
front PTO control so-
lenoid valve
D082 Wiring connector for 40-1327
front PTO control so-
lenoid valve
D082 Wiring connector for 40-1281
engine wiring loom
E005 2.8339.269.0/50 Instrument panel 40-1347

40-731
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
I008 2.7659.096.0/10 PTO engage switch 40-1306

CB A
SYNCRO
Between Pin 1 and
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
I009 2.7659.096.0/10 PTO engage switch 40-1306

CB A
ECO
Between Pin 1 and
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
I039 2.7659.177.0/20 Front PTO switch 40-1347
Resistance between
Pin 1 and Pin 2 with
button pressed: 3.9
ohms
I040 2.7659.350.0 Rear PTO switch 1 40-1347
2
3

2 220 ohm
1W
1 270 ohm

3 1W

I045 0.015.0485.4 Starter switch 1 40-1347

2
3

2 220 ohm
1W
1 270 ohm

3 1W

40-732
Wiring diagrams
Table 448
System Code P/N Description Characteristics/ Position Wiring loom
notes
I046 2.7659.097.0 1,000 rpm PTO 1 40-1347
switch
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I047 2.7659.097.0 540 rpm PTO switch 1 40-1347
Between Pin 1 and
Pin 2: normally 4

closed (NC) switch

Between Pin 3 and
Pin 4: normally open
(NO) switch
K008 PTO speed sensor 40-1300
L001 Front PTO control 40-1281
solenoid valve
L008 Rear PTO control 40-1306
solenoid valve
M006 2.8519.114.0/10 ECU PTO 40-1347
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

40-733
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q004 2.7659.351.0 Battery master 40-1330
switch

40.3.30 - S005 - PTO, cab version with front lift (AGROFARM 430 -> ZKDW430200TD25001,
AGROFARM 430 -> ZKDW550200TD30001)
M011

I049 I050 E007 I062 I063

I061
USA SENS.SIGNAL

FRONT PTO LED

SPIA PTO POST.
EV FRONT PTO
SPIA PTO ANT.

EV REAR PTO

30
EXT.PTO SW

ECONOMIC PTO
SYNCRO PTO
REAR PTO
50 15
C015 C014 C013

PTO 1000
PTO 540
+15

-31

-31

+15
-31

-31
50 15 30 1 3 2 1 3 2 41 60 17 44 43 8 5 28 2 3-13 5-16 5-13 3-8 3-14 3-24 3-9 3-11 3-10 1 2 1 2
0.018.4537.4/40

Bc017
10A

D022 D010 D038

D040 B-C3 B-B2 A-A7 B-A4 A-A3 9 2 7 3 4 5 6

B-C3 B-B2 A-A7 B-A4 A-A3 9 2 7 3 4 5 6

B001
0.016.2001.4/10*
60A

0.016.2000.4/20

0.018.5230.4/10
0.018.4891.4

3 2 1 D018 1 2 D082
1 2 1 2 1 2 9 18 17 19 8 1 2 1 2 1 2
+15

FRONT PTO
PTO AUTO

REAR PTO

-31

C005 3 2 1 C016 1 2

C004*
0.012.2756.3
0.017.8922.4/10*

I070 I072 I071

0.015.1983.4/10

L017 I066 I065

0.017.9016.4/10

0.015.4257.4/10

E013
1 2

A016 Q003 Q004

A013 A015* Q001* Q002* 3 2 1

L001
BATTERY

K008

Fig. 1157
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l Bc017 - Instrument panel fuse (key-on power) (10A)
l C004 - Earthing point
l C005 - Earthing point
l C013 - Earthing point
l C014 - Earthing point
l C015 - Earthing point
l C016 - Earthing point
l D010 - Wiring connector for front wiring loom
l D010 - Wiring connector for central wiring loom
l D018 - Wiring connector for PTO sensor wiring loom (EXPORT USA)
l D018 - Wiring connector for central wiring loom

40-734
Wiring diagrams
M011

I049 I050 E007 I062 I063

I061

USA SENS.SIGNAL

FRONT PTO LED

SPIA PTO POST.
EV FRONT PTO
SPIA PTO ANT.

EV REAR PTO
30

EXT.PTO SW

ECONOMIC PTO
SYNCRO PTO
REAR PTO
50 15
C015 C014 C013

PTO 1000
PTO 540
+15

-31

-31

+15
-31

-31
50 15 30 1 3 2 1 3 2 41 60 17 44 43 8 5 28 2 3-13 5-16 5-13 3-8 3-14 3-24 3-9 3-11 3-10 1 2 1 2
0.018.4537.4/40

Bc017
10A

D022 D010 D038

D040 B-C3 B-B2 A-A7 B-A4 A-A3 9 2 7 3 4 5 6

B-C3 B-B2 A-A7 B-A4 A-A3 9 2 7 3 4 5 6

B001

0.016.2001.4/10*
60A

0.016.2000.4/20

0.018.5230.4/10
0.018.4891.4
3 2 1 D018 1 2 D082
1 2 1 2 1 2 9 18 17 19 8 1 2 1 2 1 2

+15

FRONT PTO
PTO AUTO

REAR PTO

-31
C005 3 2 1 C016 1 2

C004*

0.012.2756.3
0.017.8922.4/10*

I070 I072 I071

0.015.1983.4/10

L017 I066 I065

0.017.9016.4/10

0.015.4257.4/10

E013
1 2

A016 Q003 Q004

A013 A015* Q001* Q002* 3 2 1

L001
BATTERY

K008

Fig. 1157
l D022 - Wiring connector for rear wiring loom
l D022 - Wiring connector for central wiring loom
l D038 - Wiring connector for RH side console wiring loom
l D038 - Wiring connector for central wiring loom and electronic lift
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l D082 - Wiring connector for front PTO control solenoid valve
l D082 - Wiring connector for engine wiring loom
l E007 - Instrument panel
l E013 - Instrument panel
l I049 - LH external PTO control
l I050 - RH external PTO control
l I061 - Ignition switch
l I062 - 1,000 rpm PTO switch
l I063 - 540 rpm PTO switch
l I065 - PTO engage switch ECO
l I066 - PTO engage switch SYNCRO
l I070 - Rear PTO switch
l I071 - Front PTO switch
l I072 - Automatic PTO switch
l K008 - PTO speed sensor
l L001 - Front PTO solenoid valve
l L017 - Rear PTO control solenoid valve
l M011 - HLHP control unit
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

40-735
 Wiring diagrams
Table 449
System Code P/N Description Characteristics/ Position Wiring loom
notes
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
Bc017 Instrument panel 40-1365
fuse (key-on power)
(10A)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C013 Earthing point 40-1365
C014 Grounding point 40-1365
C015 Grounding point 40-1365
C016 Earthing point 40-1385
D010 Wiring connector for 40-1365
front wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D018 Wiring connector for 40-1385
PTO sensor wiring
loom - (USA EX-
PORT)
D018 Wiring connector for 40-1300
central wiring loom
D022 Wiring connector for 40-1365
rear wiring loom
D022 Wiring connector for 40-1385
central wiring loom
D038 Wiring connector for 40-1365
RH side console wir-
ing loom
D038 Wiring connector for 40-1386
central wiring loom
and electronic lift
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1365
power wiring loom
D082 Wiring connector for 40-1324
front PTO control so-
lenoid valve
D082 Wiring connector for 40-1327
front PTO control so-
lenoid valve
D082 Wiring connector for 40-1281
engine wiring loom
E007 2.8339.269.0/50 Instrument panel 40-1365
E013 Lift console 40-1386
I049 LH external PTO 40-1365
control
I050 RH external PTO 40-1365
control

40-736
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
I061 0.015.0485.4 Starter switch 40-1365
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

I062 2.7659.097.0 1,000 rpm PTO 1 40-1365

switch
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I063 2.7659.097.0 540 rpm PTO switch 1 40-1365

I065 PTO engage switch 40-1385

ECO
I066 PTO engage switch 40-1385
SYNCRO
I070 2.7659.363.0 Rear PTO switch 40-1386
I071 2.7659.363.0 Front PTO switch 40-1386
I072 2.7659.363.0 Automatic PTO 40-1386
switch

Table 450
System Code P/N Description Characteristics/ Position Wiring loom
notes
K008 PTO speed sensor 40-1300
L001 Front PTO control 40-1281
solenoid valve
L017 Rear PTO control 40-1385
solenoid valve
M011 HLHP unit 40-1365
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

40-737
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q003 2.7659.351.0 Battery master 40-1330
switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40.3.31 - S005 - PTO, platform version (AGROFARM 410 -> ZKDW350200TD25001, AGRO-
FARM 410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKDW390200TD25001, AGRO-
FARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001)
M012 M015 I085 I083

I075 I076 E009 I088 I089

I087
LED F PTO FORW

FRONT PTO LED

FRONT PTO SW.

FRONT PTO LED

D+ GENERATOR

D+ GENERATOR

D+ GENERATOR
EXT. PTO COM.

FRONT PTO EV
LEDhB (LAMP)

EV REAR PTO

30
ECONOMIC PTO
REAR PTO

SYNCRO PTO
EV FORW

REAR PTO

50 15
C019 C018 C017
PTO 1000
PTO 540
PUEN
+15

+15
-31

-31

+15
-31

-31

W
50 15 30 1 3 2 1 3 2 6 1 17 2 8 14 7 12 15 12 1 11 2 7 14 6 3-20 5-16 3-13 5-13 3-8 3-14 3-24 3-9 3-11 3-10 5-24 1 2 1 2 8 3 2 4 8 3 2 4
0.018.7845.4/20

Bd017
10A

D036
4 4
to S009 (+58) 3 3
1 1
2 2

D004 D010
D040 B-C3 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B-C3 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B001
0.016.2001.4/10*
60A

0.015.7023.4/50

0.016.2000.4/20

1 2 D082 A005 A004 A003 A007

1 2 1 2 1 2 A010* A009* A008* A017*
1 2
C005
C004*
0.012.2756.3
0.017.8922.4/10*
0.015.1983.4/10

L008 I008 I009

0.017.9016.4/10

1 2

A016 Q003 Q004

A013 A015* Q001* Q002*

L001

BATTERY

Fig. 1158
l A003 - Alternator “B+”
l A004 - Alternator “D+”

40-738
Wiring diagrams
M012 M015 I085 I083

I075 I076 E009 I088 I089

I087

LED F PTO FORW

FRONT PTO LED

FRONT PTO SW.

FRONT PTO LED

D+ GENERATOR

D+ GENERATOR

D+ GENERATOR
EXT. PTO COM.

FRONT PTO EV
LEDhB (LAMP)

EV REAR PTO
30

ECONOMIC PTO
REAR PTO

SYNCRO PTO
EV FORW

REAR PTO
50 15
C019 C018 C017

PTO 1000
PTO 540
PUEN
+15

+15
-31

-31

+15
-31

-31

W
50 15 30 1 3 2 1 3 2 6 1 17 2 8 14 7 12 15 12 1 11 2 7 14 6 3-20 5-16 3-13 5-13 3-8 3-14 3-24 3-9 3-11 3-10 5-24 1 2 1 2 8 3 2 4 8 3 2 4
0.018.7845.4/20

Bd017
10A

D036
4 4
to S009 (+58) 3 3
1 1
2 2

D004 D010
D040 B-C3 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B-C3 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B001

0.016.2001.4/10*
60A

0.015.7023.4/50

0.016.2000.4/20
1 2 D082 A005 A004 A003 A007
1 2 1 2 1 2 A010* A009* A008* A017*
1 2
C005
C004*
0.012.2756.3
0.017.8922.4/10*
0.015.1983.4/10

L008 I008 I009

0.017.9016.4/10

1 2

A016 Q003 Q004

A013 A015* Q001* Q002*

L001

BATTERY

Fig. 1158
l A005 - Alternator “W”
l A007 - Battery positive terminal
l A008 - Alternator “B+”
l A009 - Alternator “D+”
l A010 - Alternator “W”
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A017 - Battery positive terminal
l B001 - 60A fuse
l Bd017 - Instrument panel fuse (key-on power) (10A)
l C004 - Earthing point
l C005 - Earthing point
l C017 - Earthing point
l C018 - Earthing point
l C019 - Earthing point
l D004 - Wiring connector for rear wiring loom
l D004 - Wiring connector for central wiring loom
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D036 - Wiring connector
l D036 - Wiring connector for lower wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l D082 - Wiring connector for front PTO control solenoid valve
l D082 - Wiring connector for engine wiring loom
l E009 - Instrument panel
l I008 - PTO engage switch SYNCRO
l I009 - PTO engage switch ECO

40-739
 Wiring diagrams
M012 M015 I085 I083

I075 I076 E009 I088 I089

I087

LED F PTO FORW

FRONT PTO LED

FRONT PTO SW.

FRONT PTO LED

D+ GENERATOR

D+ GENERATOR

D+ GENERATOR
EXT. PTO COM.

FRONT PTO EV
LEDhB (LAMP)

EV REAR PTO
30

ECONOMIC PTO
REAR PTO

SYNCRO PTO
EV FORW

REAR PTO
50 15
C019 C018 C017

PTO 1000
PTO 540
PUEN
+15

+15
-31

-31

+15
-31

-31

W
50 15 30 1 3 2 1 3 2 6 1 17 2 8 14 7 12 15 12 1 11 2 7 14 6 3-20 5-16 3-13 5-13 3-8 3-14 3-24 3-9 3-11 3-10 5-24 1 2 1 2 8 3 2 4 8 3 2 4
0.018.7845.4/20

Bd017
10A

D036
4 4
to S009 (+58) 3 3
1 1
2 2

D004 D010
D040 B-C3 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B-C3 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B001

0.016.2001.4/10*
60A

0.015.7023.4/50

0.016.2000.4/20
1 2 D082 A005 A004 A003 A007
1 2 1 2 1 2 A010* A009* A008* A017*
1 2
C005
C004*
0.012.2756.3
0.017.8922.4/10*
0.015.1983.4/10

L008 I008 I009

0.017.9016.4/10

1 2

A016 Q003 Q004

A013 A015* Q001* Q002*

L001

BATTERY

Fig. 1158
l I075 - LH external PTO control
l I076 - RH external PTO control
l I083 - Rear PTO switch
l I085 - Front PTO switch
l I087 - Ignition switch
l I088 - 1,000 rpm PTO switch
l I089 - 540 rpm PTO switch
l L001 - Front PTO solenoid valve
l L008 - Rear PTO control solenoid valve
l M012 - ECU Rear PTO
l M015 - ECU Front PTO
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 451
System Code P/N Description Characteristics/ Position Wiring loom
notes
A003 01182961 Alternator “B+” 40-1324
A004 01182961 Alternator “D+” 40-1324
A005 01182961 Alternator “W” 40-1324
A007 Battery positive ter- 40-1324
minal
A008 01182961 Alternator “B+” 40-1327
A009 01182961 Alternator “D+” 40-1327
A010 01182961 Alternator “W” 40-1327
A013 Battery +30 40-1295

40-740
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A017 Battery positive ter- 40-1327
minal
B001 0.900.0783.1 60A fuse 40-1295
Bd017 Instrument panel 40-1392
fuse (key-on power)
(10A)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C017 Earthing point 40-1392
C018 Earthing point 40-1392
C019 Grounding point 40-1392
D004 Wiring connector for 40-1392
rear wiring loom
D004 Wiring connector for 40-1306
central wiring loom
D010 Wiring connector for 40-1392
engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D036 Wiring connector 40-1392
D036 Wiring connector for 40-1392
switch wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1392
power wiring loom
D082 Wiring connector for 40-1324
front PTO control so-
lenoid valve
D082 Wiring connector for 40-1327
front PTO control so-
lenoid valve
D082 Wiring connector for 40-1281
engine wiring loom
E009 Instrument panel 40-1392
I008 2.8339.269.0/50 PTO engage switch 40-1306
CB A

SYNCRO
Between Pin 1 and
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
I009 2.7659.096.0/10 PTO engage switch 40-1306
CB A

ECO
Between Pin 1 and
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
I075 LH external PTO 40-1392
control

40-741
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
I076 RH external PTO 40-1392
control
I083 2.7659.350.0 Rear PTO switch 1 40-1392
2
3

2 220 ohm
1W
1 270 ohm

3 1W

I085 2.7659.277.0 Front PTO switch 40-1392

I087 0.015.0485.4 Starter switch 40-1392

Table 452
System Code P/N Description Characteristics/ Position Wiring loom
notes
I088 2.7659.097.0 1,000 rpm PTO 1 40-1392
switch
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I089 2.7659.097.0 540 rpm PTO switch 1 40-1392
Between Pin 1 and
Pin 2: normally 4

closed (NC) switch

Between Pin 3 and
Pin 4: normally open
(NO) switch
L001 Front PTO control 40-1281
solenoid valve
L008 Rear PTO control 40-1306
solenoid valve
M012 ECU Rear PTO 40-1392
M015 2.8519.115.0/20 ECU Front PTO 40-1392
Q001 2.7659.351.0 Battery master 40-1330
switch

40-742
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q002 2.7659.351.0 Battery master 40-1330
switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-743
 Wiring diagrams
40.3.32 - S005 - PTO, platform version - USA (AGROFARM 410 -> ZKDW350200TD25001,
AGROFARM 410 -> ZKDW470200TD30001, AGROFARM 420 -> ZKDW390200TD25001,
AGROFARM 420 -> ZKDW510200TD30001, AGROFARM 430 -> ZKDW430200TD25001)
I099 I097 M016
I090 I091 E011 I103 I104
I102

SEGNALE SENS.USA
FRONT PTO LED
FRONT PTO SW.

FRONT PTO LED

D+ GENERATOR

D+ GENERATOR
FRONT PTO EV
REAR PTO LED
REAR PTO SW.

REAR PTO LED

SENS. ENABLE
EV REAR PTO
30

ECONOMIC PTO
SYNCRO PTO
50 15
C020 C022

PTO 1000
PTO 540
+15

-31

+15
-31

-31

W
50 15 30 8 3 2 7 8 3 2 7 1 2 1 2 6 1 17 2 9 14 7 12 15 11 18 3-20 5-16 3-13 5-13 3-8 3-14 3-24 3-9 3-11 3-10 5-24 1 2 1 2
0.018.8008.4

D037
2 2
9 9
1 1
3 3 to S009 (+58)
4 4

Bh017
10A

D004 D010
D040 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

C021 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B001

0.016.2001.4/10*
60A

0.015.7023.4/50

0.016.2000.4/20
1 2 D082 A005 A004 A003 A007
1 2 3
D018
1 2 1 2 1 2 A010* A009* A008* A017*
1 2
C005 1 2 3

C004*
0.012.2756.3
0.017.8922.4/10*

0.015.4257.4/10
0.015.1983.4/10

L008 I008 I009

0.017.9016.4/10

1 2

A016 Q003 Q004

A013 A015* Q001* Q002* 1 2 3

L001

K008

BATTERY

Fig. 1159
l A003 - Alternator “B+”
l A004 - Alternator “D+”
l A005 - Alternator “W”
l A007 - Battery positive terminal
l A008 - Alternator “B+”
l A009 - Alternator “D+”
l A010 - Alternator “W”
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l A017 - Battery positive terminal
l B001 - 60A fuse
l Bh017 - Instrument panel fuse (key-on power) (10A)
l C004 - Earthing point
l C005 - Earthing point
l C020 - Earthing point
l C021 - Earthing point
l C022 - Earthing point
l D004 - Wiring connector for rear wiring loom
l D004 - Wiring connector for central wiring loom

40-744
Wiring diagrams
I099 I097 M016
I090 I091 E011 I103 I104
I102

SEGNALE SENS.USA
FRONT PTO LED
FRONT PTO SW.

FRONT PTO LED

D+ GENERATOR

D+ GENERATOR
FRONT PTO EV
REAR PTO LED
REAR PTO SW.

REAR PTO LED

SENS. ENABLE
EV REAR PTO
30

ECONOMIC PTO
SYNCRO PTO
50 15
C020 C022

PTO 1000
PTO 540
+15

-31

+15
-31

-31

W
50 15 30 8 3 2 7 8 3 2 7 1 2 1 2 6 1 17 2 9 14 7 12 15 11 18 3-20 5-16 3-13 5-13 3-8 3-14 3-24 3-9 3-11 3-10 5-24 1 2 1 2
0.018.8008.4

D037
2 2
9 9
1 1
3 3 to S009 (+58)
4 4

Bh017
10A

D004 D010
D040 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

C021 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B001

0.016.2001.4/10*
60A

0.015.7023.4/50

0.016.2000.4/20
1 2 D082 A005 A004 A003 A007
1 2 3
D018
1 2 1 2 1 2 A010* A009* A008* A017*
1 2
C005 1 2 3

C004* 0.012.2756.3
0.017.8922.4/10*

0.015.4257.4/10
0.015.1983.4/10

L008 I008 I009

0.017.9016.4/10

1 2

A016 Q003 Q004

A013 A015* Q001* Q002* 1 2 3

L001

K008

BATTERY

Fig. 1159
l D010 - Wiring connector for engine wiring loom
l D010 - Wiring connector for central wiring loom
l D018 - Wiring connector for PTO sensor wiring loom (EXPORT USA)
l D018 - Wiring connector for central wiring loom
l D037 - Wiring connector
l D037 - Wiring connector for lower wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l D082 - Wiring connector for front PTO control solenoid valve
l D082 - Wiring connector for engine wiring loom
l E011 - Instrument panel
l I008 - PTO engage switch SYNCRO
l I009 - PTO engage switch ECO
l I090 - LH external PTO control
l I091 - RH external PTO control
l I097 - Rear PTO switch
l I099 - Front PTO switch
l I102 - Ignition switch
l I103 - 1,000 rpm PTO switch
l I104 - 540 rpm PTO switch
l K008 - PTO speed sensor
l L001 - Front PTO solenoid valve
l L008 - Rear PTO control solenoid valve
l M016 - ECU Rear PTO

40-745
 Wiring diagrams
I099 I097 M016
I090 I091 E011 I103 I104
I102

SEGNALE SENS.USA
FRONT PTO LED
FRONT PTO SW.

FRONT PTO LED

D+ GENERATOR

D+ GENERATOR
FRONT PTO EV
REAR PTO LED
REAR PTO SW.

REAR PTO LED

SENS. ENABLE
EV REAR PTO
30

ECONOMIC PTO
SYNCRO PTO
50 15
C020 C022

PTO 1000
PTO 540
+15

-31

+15
-31

-31

W
50 15 30 8 3 2 7 8 3 2 7 1 2 1 2 6 1 17 2 9 14 7 12 15 11 18 3-20 5-16 3-13 5-13 3-8 3-14 3-24 3-9 3-11 3-10 5-24 1 2 1 2
0.018.8008.4

D037
2 2
9 9
1 1
3 3 to S009 (+58)
4 4

Bh017
10A

D004 D010
D040 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

C021 A-A7 B-C3 B-B2 A-A1 A-A8 A-D1 B-D1 B-A4 A-A3 9 8 2 6

B001

0.016.2001.4/10*
60A

0.015.7023.4/50

0.016.2000.4/20
1 2 D082 A005 A004 A003 A007
1 2 3
D018
1 2 1 2 1 2 A010* A009* A008* A017*
1 2
C005 1 2 3

C004* 0.012.2756.3
0.017.8922.4/10*

0.015.4257.4/10
0.015.1983.4/10

L008 I008 I009

0.017.9016.4/10

1 2

A016 Q003 Q004

A013 A015* Q001* Q002* 1 2 3

L001

K008

BATTERY

Fig. 1159
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

Table 453
System Code P/N Description Characteristics/ Position Wiring loom
notes
A003 01182961 Alternator “B+” 40-1324
A004 01182961 Alternator “D+” 40-1324
A005 01182961 Alternator “W” 40-1324
A007 Battery positive ter- 40-1324
minal
A008 01182961 Alternator “B+” 40-1327
A009 01182961 Alternator “D+” 40-1327
A010 01182961 Alternator “W” 40-1327
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
A017 Battery positive ter- 40-1327
minal

40-746
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
B001 0.900.0783.1 60A fuse 40-1295
Bh017 Instrument panel 40-1410
fuse (key-on power)
(10A)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C020 Grounding point 40-1410
C021 Grounding point 40-1410
C022 Grounding point 40-1410
D004 Wiring connector for 40-1410
rear wiring loom
D004 Wiring connector for 40-1306
central wiring loom
D010 Wiring connector for 40-1410
engine wiring loom
D010 Wiring connector for 40-1324
central wiring loom
D018 Wiring connector for 40-1300
central wiring loom
D018 Wiring connector for 40-1306
PTO sensor wiring
loom - (USA EX-
PORT)
D037 Wiring connector 40-1410
D037 Wiring connector for 40-1410
switch wiring loom
D040 Wiring connector for 40-1295
central wiring loom
D040 Wiring connector for 40-1410
power wiring loom
D082 Wiring connector for 40-1324
front PTO control so-
lenoid valve
D082 Wiring connector for 40-1327
front PTO control so-
lenoid valve
D082 Wiring connector for 40-1281
engine wiring loom
E011 2.8339.269.0/50 Instrument panel 40-1410
I008 2.7659.096.0/10 PTO engage switch 40-1306
CB A

SYNCRO
Between Pin 1 and
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
I009 2.7659.096.0/10 PTO engage switch 40-1306
CB A

ECO
Between Pin 1 and
Pin 2: Normally
closed (NC) contact
Between Pin 2 and
Pin 3: Normally open
(NO) contact
I090 LH external PTO 40-1410
control

40-747
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
I091 RH external PTO 40-1410
control
I097 2.7659.350.0 Rear PTO switch 1 40-1410
2
3

2 220 ohm
1W
1 270 ohm

3 1W

I099 2.7659.277.0 Front PTO switch 40-1410

I102 0.015.0485.4 Starter switch 40-1410

83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

Table 454
System Code P/N Description Characteristics/ Position Wiring loom
notes
I103 2.7659.097.0 1,000 rpm PTO 1 40-1410
switch
Between Pin 1 and 4

Pin 2: normally
closed (NC) switch
Between Pin 3 and
Pin 4: normally open
(NO) switch
I104 2.7659.097.0 540 rpm PTO switch 1 40-1410
Between Pin 1 and
Pin 2: normally 4

closed (NC) switch

Between Pin 3 and
Pin 4: normally open
(NO) switch
K008 PTO speed sensor 40-1300
L001 Front PTO control 40-1281
solenoid valve
L008 Rear PTO control 40-1306
solenoid valve
M016 2.8519.115.0/20 ECU Rear PTO 40-1410

40-748
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-749
 Wiring diagrams
40.3.33 - S006 - Windscreen wipers, cab with high visibility roof
I035 Ja003 Ja004 N014 N015
30
50 15
C007 C009
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.3567.4/60

Ba016 Ba026 Ba022 Ba011

30 A

30A

15A
3A

to S009 (+58)
D030
D040 D039 D013 2 6 5 3

2 6 5 3
0.016.0373.4/30

B001 B004 B003

60A

60A

60A

2 6 5 3 D029

2 6 5 3

C005
C004*
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

Be005 Be006
7,5A

7,5A
C023

0.015.6272.4/40
A013 A011 A015* Q001* Q002*
A012 A016 Q003 Q004

BATTERY

4 3 2 1
D044
1 2 3 5 6 7 8 2 3 8 7 15 53S I-6 T 53M 31 5 2 6 3 7 8 2 3

4 3 2 1

I004 I006 H008 I005 N010

0.011.3597.3

4 3 2 1

N004

Fig. 1160
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba022 - Protection fuse, FT 5-6-7-8 (30A)
l Ba025 - Protection fuse (40A)
l Be005 - Fuse 5 in fuse box F (7.5A - Windscreen wiper)
l Be006 - Fuse 6 in fuse box F (7.5A - Rear screen wiper)
l C004 - Earthing point
l C005 - Earthing point
l C007 - Earthing point
l C009 - Earthing point
l C023 - Earthing point
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D029 - Wiring connector for roof wiring loom
l D029 - Wiring connector to cab power wiring loom
l D029 - Connection between cab power wiring loom and HV roof wiring loom
l D030 - Wiring connector for central cab wiring loom

40-750
Wiring diagrams
I035 Ja003 Ja004 N014 N015
30
50 15
C007 C009
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.3567.4/60

Ba016 Ba026 30 A Ba022 Ba011

30A

15A
3A

to S009 (+58)
D030
D040 D039 D013 2 6 5 3

2 6 5 3
0.016.0373.4/30

B001 B004 B003

60A

60A

60A

2 6 5 3 D029

2 6 5 3

C005
C004*
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

Be005 Be006
7,5A

7,5A
C023

0.015.6272.4/40
A013 A011 A015* Q001* Q002*
A012 A016 Q003 Q004

BATTERY

4 3 2 1
D044
1 2 3 5 6 7 8 2 3 8 7 15 53S I-6 T 53M 31 5 2 6 3 7 8 2 3

4 3 2 1

I004 I006 H008 I005 N010

0.011.3597.3

4 3 2 1

N004

Fig. 1160
l D030 - Wiring connector to cab power wiring loom
l D039 - Wiring connector for central cab wiring loom
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l D044 - Wiring connector for roof wiring loom
l D044 - Wiring connector for windscreen wiper motor wiring loom
l H008 - Windscreen wiper timer
l I004 - Windscreen wiper switch
l I005 - Rear screen wiper switch
l I006 - Windscreen washer button
l I035 - Ignition switch
l Ja003 - Key-on power relay for fuses F11-12-13
l Ja004 - Key-on power relay for fuses F5-6-7-8
l N004 - Windscreen wiper motor
l N010 - Rear window wiper motor
l N014 - Front screenwash pump
l N015 - Rear screenwash pump
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

40-751
 Wiring diagrams
Table 455
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Ba011 Turn indicator lights 40-1331
fuse (key-on power)
(15A)
Ba016 Relay fuse (key-on 40-1331
power) (3A)
Ba022 Protection fuse, FT 40-1331
5-6-7-8 (30A)
Ba025 Protection fuse 40-1331
(40A)
Be005 Fuse 5 in fuse box F 40-1301
(7.5A - Windscreen
wiper)
Be006 Fuse 6 in fuse box F 40-1301
(7.5A - Rear screen
wiper)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C007 Earthing point 40-1331
C009 Earthing point 40-1331
C023 Grounding point 40-1301
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1331
power wiring loom
D029 Wiring connector for 40-1311
roof wiring loom
D029 Wiring connector for 40-1301
cab power wiring
loom
D029 Connection between 40-1301
cab power supply
wiring and HV roof
wiring
D030 Wiring connector for 40-1311
central cab wiring
loom
D030 Wiring connector for 40-1331
cab power wiring
loom
D039 Wiring connector for [LNK] 40-1295
central cab wiring
loom
D039 Wiring connector for [LNK] 40-1331
power wiring loom
D040 Wiring connector for [LNK] 40-1295
central wiring loom

40-752
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
D040 Wiring connector for [LNK] 40-1331
power wiring loom
D044 Wiring connector for [LNK] 40-1279
roof wiring loom
D044 Wiring connector for [LNK] 40-1301
windscreen wiper
motor wiring loom
H008 Windscreen wiper [LNK] 40-1301
timer
Table 456
System Code P/N Description Characteristics/ Position Wiring loom
notes
I004 2.7659.224.0/10 Windscreen wiper 40-1301
switch

I005 2.7659.192.0/10 Rear screen wiper 40-1301

switch

I006 2.7659.192.0/10 Windscreen washer 40-1301

button

I035 0.015.0485.4 Starter switch 40-1331

83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

Ja003 Key-on power relay [LNK] 40-1331

for fuses F11-12-13
Ja004 Key-on power relay [LNK] 40-1331
for fuses F5-6-7-8
N004 Windscreen wiper [LNK] 40-1279
motor
N010 Rear window wiper [LNK] 40-1301
motor
N014 Front screenwash [LNK] 40-1331
pump
N015 Rear screenwash [LNK] 40-1331
pump

40-753
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-754
Wiring diagrams
40.3.34 - S006 - Windscreen wipers, standard cab with heater and air conditioning
I035 Ja003 Ja004 N014 N015
30
50 15
C007 C009
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.3567.4/60

Ba016 Ba026 Ba022 Ba011

30 A

30A

15A
3A

D030
D040 D039 D013 2 5 3

2 5 3

0.016.0373.4/30
B001 B004 B003
60A

60A

60A

2 5 3
D029

2 5 3

C005 C006
C004* Bg005 Bg006
0.017.8922.4/10*

7,5A

7,5A
0.015.1983.4/10

0.017.9016.4/10

0.018.5825.4
A013 A011 A015* Q001* Q002*
A012 A016 Q003 Q004
6 3 2 1
D045 3 7
D046
1 2 3 4 8 7 5 6 1 2 15 53S I-6 T 53M 31 1 2 3 4 8 7 5 6

6 3 2 1 3 7

0.016.0866.4/10
BATTERY

I021 I017 H031 I018

0.010.4516.3

1 2 D047
4 3 2 1 1 2

0.015.6123.4
N003

1 2

N006

Fig. 1161
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba022 - Protection fuse, FT 5-6-7-8 (30A)
l Ba026 - MK3 relay fuse 30A
l C007 - Earthing point
l C009 - Earthing point
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D029 - Wiring connector for roof wiring loom
l D030 - Wiring connector for central cab wiring loom
l D030 - Wiring connector to cab power wiring loom
l D039 - Wiring connector for central cab wiring loom
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l D045 - Wiring connector for roof wiring loom
l D046 - Wiring connector to cab roof wiring loom, versions with standard cab
l D047 - Wiring connector for rear screen wiper wiring loom, versions without high visibility cab
l D047 - Wiring connector for work lights and windscreen wiper wiring loom, versions without high visibility cab
l I035 - Ignition switch
l Ja003 - Key-on power relay for fuses F11-12-13

40-755
 Wiring diagrams
I035 Ja003 Ja004 N014 N015
30
50 15
C007 C009
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.3567.4/60

Ba016 Ba026 Ba022 Ba011

30 A

30A

15A
3A

D030
D040 D039 D013 2 5 3

2 5 3

0.016.0373.4/30
B001 B004 B003
60A

60A

60A

2 5 3
D029

2 5 3

C005 C006
C004* Bg005 Bg006
0.017.8922.4/10*

7,5A

7,5A
0.015.1983.4/10

0.017.9016.4/10

0.018.5825.4
A013 A011 A015* Q001* Q002*
A012 A016 Q003 Q004
6 3 2 1
D045 3 7
D046
1 2 3 4 8 7 5 6 1 2 15 53S I-6 T 53M 31 1 2 3 4 8 7 5 6

6 3 2 1 3 7

0.016.0866.4/10
BATTERY

I021 I017 H031 I018

0.010.4516.3

1 2 D047
4 3 2 1 1 2

0.015.6123.4
N003

1 2

N006

Fig. 1161
l Ja004 - Key-on power relay for fuses F5-6-7-8
l N003 - Windscreen wiper motor
l N006 - Rear window wiper motor
l N014 - Front screenwash pump
l N015 - Rear screenwash pump
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 457
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Ba011 Turn indicator lights 40-1331
fuse (key-on power)
(15A)
Ba016 Relay fuse (key-on 40-1331
power) (3A)
Ba022 Protection fuse, FT 40-1331
5-6-7-8 (30A)

40-756
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Ba026 MK3 relay fuse 30A 40-1331
C007 Earthing point 40-1331
C009 Earthing point 40-1331
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1331
power wiring loom
D029 Wiring connector for 40-1311
roof wiring loom
D030 Wiring connector for 40-1311
central cab wiring
loom
D030 Wiring connector for 40-1331
cab power wiring
loom
D039 Wiring connector for [LNK] 40-1295
central cab wiring
loom
D039 Wiring connector for [LNK] 40-1331
power wiring loom
D040 Wiring connector for [LNK] 40-1295
central wiring loom
D040 Wiring connector for [LNK] 40-1331
power wiring loom
D045 Wiring connector for [LNK] 40-1276
roof wiring loom
D046 Wiring connector to [LNK] 40-1322
cab roof wiring loom,
versions with stan-
dard cab
D047 Wiring connector for [LNK] 40-1322
rear screen wiper
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for [LNK] 40-1300
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
I035 0.015.0485.4 Starter switch 40-1331
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

Ja003 Key-on power relay [LNK] 40-1331

for fuses F11-12-13
Ja004 Key-on power relay [LNK] 40-1331
for fuses F5-6-7-8
N003 Windscreen wiper [LNK] 40-1276
motor

40-757
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
N006 Rear window wiper [LNK] 40-1300
motor
N014 Front screenwash [LNK] 40-1331
pump
N015 Rear screenwash [LNK] 40-1331
pump
Table 458
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-758
Wiring diagrams
40.3.35 - S006 - Windscreen wipers, version with standard cab (AGROFARM 410 ->
ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 ->
ZKDW430200TD25001)
I035 Ja003 Ja004 N014 N015
30
50 15
C007 C009
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.3567.4/60

Ba016 Ba026 Ba022 Ba011

30 A

30A

15A
3A

D030
D040 D039 D013 2 5 3

2 5 3
0.016.0373.4/30

B001 B004 B003

60A

60A

60A

2 5 3
D029

2 5 3

C005 C003
C004* Bf005 7,5A Bf006

7,5A
0.017.8922.4/10*
0.015.1983.4/10

0.016.0865.4/10
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004
6 3 2 1
D045 3 7
D046
1 2 3 4 8 7 5 6 1 2 15 53S I-6 T 53M 31 1 2 3 4 8 7 5 6

6 3 2 1 3 7

0.016.0866.4/10
BATTERY

I014 I012 H010 I011

0.010.4516.3

1 2 D047
4 3 2 1 1 2

0.015.6123.4
N003

1 2

N006

Fig. 1162
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Ba011 - Turn indicator lights fuse (key-on power) (15A)
l Ba016 - Relay fuse (key-on power) (3A)
l Ba022 - Protection fuse, FT 5-6-7-8 (30A)
l Ba026 - MK3 relay fuse 30A
l Bf005 - Fuse 5 in fuse box F (7.5A - Windscreen wiper)
l Bf006 - Fuse 6 in fuse box F (7.5A - Rear screen wiper)
l C003 - Earthing point
l C004 - Earthing point
l C005 - Earthing point
l C007 - Earthing point
l C009 - Earthing point
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D029 - Wiring connector for roof wiring loom
l D029 - Wiring connector to cab power wiring loom
l D030 - Wiring connector for central cab wiring loom
l D030 - Wiring connector to cab power wiring loom
l D039 - Wiring connector for central cab wiring loom

40-759
 Wiring diagrams
I035 Ja003 Ja004 N014 N015
30
50 15
C007 C009
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.3567.4/60

Ba016 Ba026 Ba022 Ba011

30 A

30A

15A
3A

D030
D040 D039 D013 2 5 3

2 5 3

0.016.0373.4/30
B001 B004 B003
60A

60A

60A

2 5 3
D029

2 5 3

C005 C003
C004* Bf005 Bf006

7,5A

7,5A
0.017.8922.4/10*
0.015.1983.4/10

0.016.0865.4/10
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004
6 3 2 1
D045 3 7
D046
1 2 3 4 8 7 5 6 1 2 15 53S I-6 T 53M 31 1 2 3 4 8 7 5 6

6 3 2 1 3 7

0.016.0866.4/10
BATTERY

I014 I012 H010 I011

0.010.4516.3

1 2 D047
4 3 2 1 1 2

0.015.6123.4
N003

1 2

N006

Fig. 1162
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l D045 - Wiring connector for roof wiring loom
l D045 - Wiring connector for windscreen wiper wiring loom
l D046 - Wiring connector to cab roof wiring loom, versions with standard cab
l D046 - Wiring connector for work lights and windscreen wiper wiring loom, versions without high visibility cab
l D047 - Wiring connector for rear screen wiper wiring loom, versions without high visibility cab
l D047 - Wiring connector for work lights and windscreen wiper wiring loom, versions without high visibility cab
l H010 - Timer
l I011 - Rear screen wiper switch
l I012 - Windscreen washer pump switch
l I014 - Windscreen wiper switch
l I035 - Ignition switch
l Ja003 - Key-on power relay for fuses F11-12-13
l Ja004 - Key-on power relay for fuses F5-6-7-8
l N003 - Windscreen wiper motor
l N006 - Rear window wiper motor
l N014 - Front screenwash pump
l N015 - Rear screenwash pump
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

40-760
Wiring diagrams
Table 459
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Ba011 Turn indicator lights 40-1331
fuse (key-on power)
(15A)
Ba016 Relay fuse (key-on 40-1331
power) (3A)
Ba022 Protection fuse, FT 40-1331
5-6-7-8 (30A)
Ba026 MK3 relay fuse 30A 40-1331
Bf005 Fuse 5 in fuse box F 40-1318
(7.5A - Windscreen
wiper)
Bf006 Fuse 6 in fuse box F 40-1318
(7.5A - Rear screen
wiper)
C003 Earthing point 40-1318
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C007 Earthing point 40-1331
C009 Earthing point 40-1331
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1331
power wiring loom
D029 Wiring connector for 40-1311
roof wiring loom
D029 Wiring connector for 40-1318
cab power wiring
loom
D030 Wiring connector for 40-1311
central cab wiring
loom
D030 Wiring connector for 40-1331
cab power wiring
loom
D039 Wiring connector for [LNK] 40-1295
central cab wiring
loom
D039 Wiring connector for [LNK] 40-1331
power wiring loom
D040 Wiring connector for [LNK] 40-1295
central wiring loom
D040 Wiring connector for [LNK] 40-1331
power wiring loom
D045 Wiring connector for [LNK] 40-1276
roof wiring loom

40-761
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
D045 Wiring connector for 40-1318
windscreen wiper
wiring loom
D046 Wiring connector to [LNK] 40-1322
cab roof wiring loom,
versions with stan-
dard cab
D046 Wiring connector for 40-1318
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
Table 460
System Code P/N Description Characteristics/ Position Wiring loom
notes
D047 Wiring connector for [LNK] 40-1322
rear screen wiper
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for [LNK] 40-1300
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
H010 Timer [LNK] 40-1318
I011 2.7659.091.0 Rear screen wiper 0
40-1318
switch
1
3

1
2
4

Pin 1 2
Pos

I012 2.7659.146.0 Windscreen washer 1

0
40-1318
2
pump switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6
Pos

I014 2.7659.092.0 Windscreen wiper 1

0
40-1318
2
switch
1 2 3 4

5 6 7 8

Pin 1 2 3 4 5 6 7 8
Pos

I035 0.015.0485.4 Starter switch 40-1331

83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

Ja003 Key-on power relay [LNK] 40-1331

for fuses F11-12-13

40-762
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Ja004 Key-on power relay [LNK] 40-1331
for fuses F5-6-7-8
N003 Windscreen wiper [LNK] 40-1276
motor
N006 Rear window wiper [LNK] 40-1300
motor
N014 Front screenwash [LNK] 40-1331
pump
N015 Rear screenwash [LNK] 40-1331
pump
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-763
 Wiring diagrams
40.3.36 - S006 - Windscreen wipers, cab with high visibility roof - USA
I045 Jb003 Jb004 N007 N011
30
50 15
C010 C012
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.4081.4/30

Bb016 Bb026 Bb022 Bb011

30 A

30A

15A
3A

to S009 (+58)
D030
D040 D039 D013 2 6 5 3

2 6 5 3

0.016.0373.4/30
B001 B004 B003
60A

60A

60A

2 6 5 3 D029

2 6 5 3

C005
C004*
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

Be005 Be006

7,5A

7,5A
C023

0.015.6272.4/40
A013 A011 A015* Q001* Q002*
A012 A016 Q003 Q004

BATTERY

4 3 2 1
D044
1 2 3 5 6 7 8 2 3 8 7 15 53S I-6 T 53M 31 5 2 6 3 7 8 2 3

4 3 2 1

I004 I006 H008 I005 N010

0.011.3597.3

4 3 2 1

N004

Fig. 1163
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb022- Protection fuse, FT 5-6-7-8 (30A)
l Bb026 - Protection fuse (40A)
l Be005 - Fuse 5 in fuse box F (7.5A - Windscreen wiper)
l Be006 - Fuse 6 in fuse box F (7.5A - Rear screen wiper)
l C004 - Earthing point
l C005 - Earthing point
l C010 - Earthing point
l C012 - Earthing point
l C023 - Earthing point
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D029 - Wiring connector for roof wiring loom
l D029 - Wiring connector to cab power wiring loom
l D029 - Connection between cab power wiring loom and HV roof wiring loom
l D030 - Wiring connector for central cab wiring loom
l D030 - Wiring connector to cab power wiring loom
l D039 - Wiring connector for central cab wiring loom

40-764
Wiring diagrams
I045 Jb003 Jb004 N007 N011
30
50 15
C010 C012
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.4081.4/30

Bb016 Bb026 Bb022 Bb011

30 A

30A

15A
3A

to S009 (+58)
D030
D040 D039 D013 2 6 5 3

2 6 5 3

0.016.0373.4/30
B001 B004 B003
60A

60A

60A

2 6 5 3 D029

2 6 5 3

C005
C004*
0.017.8922.4/10*
0.015.1983.4/10

0.017.9016.4/10

Be005 Be006

7,5A

7,5A
C023

0.015.6272.4/40
A013 A011 A015* Q001* Q002*
A012 A016 Q003 Q004

BATTERY

4 3 2 1
D044
1 2 3 5 6 7 8 2 3 8 7 15 53S I-6 T 53M 31 5 2 6 3 7 8 2 3

4 3 2 1

I004 I006 H008 I005 N010

0.011.3597.3

4 3 2 1

N004

Fig. 1163
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l D044 - Wiring connector for roof wiring loom
l D044 - Wiring connector for windscreen wiper motor wiring loom
l H008 - Windscreen wiper timer
l I004 - Windscreen wiper switch
l I005 - Rear screen wiper switch
l I006 - Windscreen washer button
l I045 - Ignition switch
l Jb003 - Key-on power relay for fuses F11-12-13
l Jb004 Key-on power relay for fuses F5-6-7-8
l N004 - Windscreen wiper motor
l N007 - Windscreen washer pump
l N010 - Rear window wiper motor
l N011 - Rear screen washer pump
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch

40-765
 Wiring diagrams
Table 461
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Bb011 Turn indicator lights 40-1347
fuse (key-on power)
(15A)
Bb016 Relay fuse (key-on 40-1347
power) (3A)
Bb022 Protection fuse, FT 40-1347
5-6-7-8 (30A)
Bb026 MK3 relay fuse 30A 40-1347
Be005 Fuse 5 in fuse box F 40-1301
(7.5A - Windscreen
wiper)
Be006 Fuse 6 in fuse box F 40-1301
(7.5A - Rear screen
wiper)
C004 Earthing point 40-1330
C005 Earthing point 40-1330
C010 Grounding point 40-1347
C012 Earthing point 40-1347
C023 Grounding point 40-1301
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1347
power wiring loom
D029 Wiring connector for 40-1311
roof wiring loom
D029 Wiring connector for 40-1301
cab power wiring
loom
D029 Connection between 40-1301
cab power supply
wiring and HV roof
wiring
D030 Wiring connector for 40-1311
central cab wiring
loom
D030 Wiring connector for 40-1347
cab power wiring
loom
D039 Wiring connector for [LNK] 40-1295
central cab wiring
loom
D039 Wiring connector for [LNK] 40-1347
power wiring loom
D040 Wiring connector for [LNK] 40-1295
central wiring loom

40-766
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
D040 Wiring connector for [LNK] 40-1347
power wiring loom
D044 Wiring connector for [LNK] 40-1279
roof wiring loom
D044 Wiring connector for [LNK] 40-1301
windscreen wiper
motor wiring loom
H008 Windscreen wiper [LNK] 40-1301
timer
Table 462
System Code P/N Description Characteristics/ Position Wiring loom
notes
I004 2.7659.224.0/10 Windscreen wiper 40-1301
switch

I005 2.7659.192.0/10 Rear screen wiper 40-1301

switch

I006 2.7659.223.0/10 Windscreen washer 40-1301

button

I045 0.015.0485.4 Starter switch 40-1347

83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

Jb003 Key-on power relay [LNK] 40-1347

for fuses F11-12-13
Jb004 Key-on power relay [LNK] 40-1347
for fuses F5-6-7-8
N004 Windscreen wiper [LNK] 40-1279
motor
N007 Windscreen washer [LNK] 40-1347
pump
N010 Rear window wiper [LNK] 40-1301
motor
N011 Rear screen washer [LNK] 40-1347
pump

40-767
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-768
Wiring diagrams
40.3.37 - S006 - Windscreen wipers, standard cab with heater and air conditioning - USA
I045 Jb003 Jb004 N007 N011
30
50 15
C010 C012
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.4081.4/30

Bb016 Bb026 Bb022 Bb011

30 A

30A

15A
3A

D030
D040 D039 D013 2 5 3

2 5 3

0.016.0373.4/30
B001 B004 B003
60A

60A

60A

2 5 3
D029

2 5 3

C005 C006
C004* Bg005 Bg006
0.017.8922.4/10*

7,5A

7,5A
0.015.1983.4/10

0.017.9016.4/10

0.018.5825.4
A013 A011 A015* Q001* Q002*
A012 A016 Q003 Q004
6 3 2 1
D045 3 7
D046
1 2 3 4 8 7 5 6 1 2 15 53S I-6 T 53M 31 1 2 3 4 8 7 5 6

6 3 2 1 3 7

0.016.0866.4/10
BATTERY

I021 I017 H031 I018

0.010.4516.3

1 2 D047
4 3 2 1 1 2

0.015.6123.4
N003

1 2

N006

Fig. 1164
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb022- Protection fuse, FT 5-6-7-8 (30A)
l Bb026 - Protection fuse (40A)
l C010 - Earthing point
l C012 - Earthing point
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D029 - Wiring connector for roof wiring loom
l D030 - Wiring connector for central cab wiring loom
l D030 - Wiring connector to cab power wiring loom
l D039 - Wiring connector for central cab wiring loom
l D039 - Wiring connector for power wiring loom
l D040 - Wiring connector for central wiring loom
l D040 - Wiring connector for power wiring loom
l D045 - Wiring connector for roof wiring loom
l D046 - Wiring connector to cab roof wiring loom, versions with standard cab
l D047 - Wiring connector for rear screen wiper wiring loom, versions without high visibility cab
l D047 - Wiring connector for work lights and windscreen wiper wiring loom, versions without high visibility cab
l I045 - Ignition switch
l Jb003 - Key-on power relay for fuses F11-12-13

40-769
 Wiring diagrams
I045 Jb003 Jb004 N007 N011
30
50 15
C010 C012
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.4081.4/30

Bb016 Bb026 Bb022 Bb011

30 A

30A

15A
3A

D030
D040 D039 D013 2 5 3

2 5 3

0.016.0373.4/30
B001 B004 B003
60A

60A

60A

2 5 3
D029

2 5 3

C005 C006
C004* Bg005 Bg006
0.017.8922.4/10*

7,5A

7,5A
0.015.1983.4/10

0.017.9016.4/10

0.018.5825.4
A013 A011 A015* Q001* Q002*
A012 A016 Q003 Q004
6 3 2 1
D045 3 7
D046
1 2 3 4 8 7 5 6 1 2 15 53S I-6 T 53M 31 1 2 3 4 8 7 5 6

6 3 2 1 3 7

0.016.0866.4/10
BATTERY

I021 I017 H031 I018

0.010.4516.3

1 2 D047
4 3 2 1 1 2

0.015.6123.4
N003

1 2

N006

Fig. 1164
l Jb004 Key-on power relay for fuses F5-6-7-8
l N003 - Windscreen wiper motor
l N006 - Rear window wiper motor
l N007 - Windscreen washer pump
l N011 - Rear screen washer pump
l Q001 - Battery master switch
l Q002 - Battery master switch
l Q003 - Battery master switch
l Q004 - Battery master switch
Table 463
System Code P/N Description Characteristics/ Position Wiring loom
notes
A011 Battery +30 40-1295
A012 Battery +30 40-1295
A013 Battery +30 40-1295
A015 Battery negative ter- 40-1330
minal
A016 Battery negative ter- 40-1330
minal
B001 0.900.0783.1 60A fuse 40-1295
B003 0.900.0783.1 60A fuse 40-1295
B004 0.900.0783.1 60A fuse 40-1295
Bb011 Turn indicator lights 40-1347
fuse (key-on power)
(15A)
Bb016 Relay fuse (key-on 40-1347
power) (3A)

40-770
Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
Bb022 Protection fuse, FT 40-1347
5-6-7-8 (30A)
Bb026 MK3 relay fuse 30A 40-1347
C010 Grounding point 40-1347
C012 Earthing point 40-1347
D013 Wiring connector for 40-1295
central wiring loom
D013 Wiring connector for 40-1347
power wiring loom
D029 Wiring connector for 40-1311
roof wiring loom
D030 Wiring connector for 40-1311
central cab wiring
loom
D030 Wiring connector for 40-1347
cab power wiring
loom
D039 Wiring connector for [LNK] 40-1295
central cab wiring
loom
D039 Wiring connector for [LNK] 40-1347
power wiring loom
D040 Wiring connector for [LNK] 40-1295
central wiring loom
D040 Wiring connector for [LNK] 40-1347
power wiring loom
D045 Wiring connector for [LNK] 40-1276
roof wiring loom
D046 Wiring connector to [LNK] 40-1322
cab roof wiring loom,
versions with stan-
dard cab
D047 Wiring connector for [LNK] 40-1322
rear screen wiper
wiring loom, ver-
sions without high
visibility cab
D047 Wiring connector for [LNK] 40-1300
work lights and wind-
screen wiper wiring
loom, versions with-
out high visibility cab
I045 0.015.0485.4 Starter switch 40-1347
83
50
30
86s

75 15

Pin 30 15 50 75 83
Pos

2
D0010060

Jb003 Key-on power relay [LNK] 40-1347

for fuses F11-12-13
Jb004 Key-on power relay [LNK] 40-1347
for fuses F5-6-7-8

40-771
 Wiring diagrams
System Code P/N Description Characteristics/ Position Wiring loom
notes
N003 Windscreen wiper [LNK] 40-1276
motor
N006 Rear window wiper [LNK] 40-1300
motor
N007 Windscreen washer [LNK] 40-1347
pump
N011 Rear screen washer [LNK] 40-1347
pump
Table 464
System Code P/N Description Characteristics/ Position Wiring loom
notes
Q001 2.7659.351.0 Battery master 40-1330
switch

Q002 2.7659.351.0 Battery master 40-1330

switch

Q003 2.7659.351.0 Battery master 40-1330

switch

Q004 2.7659.351.0 Battery master 40-1330

switch

40-772
Wiring diagrams
40.3.38 - S006 - Windscreen wipers, version with standard cab - USA (AGROFARM 410
-> ZKDW350200TD25001, AGROFARM 420 -> ZKDW390200TD25001, AGROFARM 430 ->
ZKDW430200TD25001)
I045 Jb003 Jb004 N007 N011
30
50 15
C010 C012
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.4081.4/30

Bb016 Bb026 Bb022 Bb011

30 A

30A

15A
3A

D030
D040 D039 D013 2 5 3

2 5 3
0.016.0373.4/30

B001 B004 B003

60A

60A

60A

2 5 3
D029

2 5 3

C005 C003
C004* Bf005 Bf006
0.017.8922.4/10*

7,5A

7,5A
0.015.1983.4/10

0.016.0865.4/10
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004
6 3 2 1
D045 3 7
D046
1 2 3 4 8 7 5 6 1 2 15 53S I-6 T 53M 31 1 2 3 4 8 7 5 6

6 3 2 1 3 7

0.016.0866.4/10
BATTERY

I014 I012 H010 I011

0.010.4516.3

1 2 D047
4 3 2 1 1 2

0.015.6123.4
N003

1 2

N006

Fig. 1165
l A011 - Battery +30
l A012 - Battery +30
l A013 - Battery +30
l A015 - Battery negative terminal
l A016 - Battery negative terminal
l B001 - 60A fuse
l B003 - 60A fuse
l B004 - 60A fuse
l Bb011 - Turn indicator lights fuse (key-on power) (15A)
l Bb016 - Relay fuse (key-on power) (3A)
l Bb022- Protection fuse, FT 5-6-7-8 (30A)
l Bb026 - MK3 relay fuse 30A
l Bf005 - Fuse 5 in fuse box F (7.5A - Windscreen wiper)
l Bf006 - Fuse 6 in fuse box F (7.5A - Rear screen wiper)
l C003 - Earthing point
l C004 - Earthing point
l C005 - Earthing point
l C010 - Earthing point
l C012 - Earthing point
l D013 - Wiring connector for central wiring loom
l D013 - Wiring connector for power wiring loom
l D029 - Wiring connector for roof wiring loom
l D029 - Wiring connector to cab power wiring loom
l D030 - Wiring connector for central cab wiring loom
l D030 - Wiring connector to cab power wiring loom
l D039 - Wiring connector for central cab wiring loom

40-773
 Wiring diagrams
I045 Jb003 Jb004 N007 N011
30
50 15
C010 C012
50 15 30 30 85 86 87 30 85 86 87 1 2 2 1
0.018.4081.4/30

Bb016 Bb026 Bb022 Bb011

30 A

30A

15A
3A

D030
D040 D039 D013 2 5 3

2 5 3

0.016.0373.4/30
B001 B004 B003
60A

60A

60A

2 5 3
D029

2 5 3

C005 C003
C004* Bf005 Bf006
0.017.8922.4/10*

7,5A

7,5A
0.015.1983.4/10

0.016.0865.4/10
0.017.9016.4/10

A013 A011 A015* Q001* Q002*

A012 A016 Q003 Q004
6 3 2 1
D045 3 7
D046
1 2 3 4 8 7 5 6 1 2 15 53S I-6 T 53M 31 1 2 3 4 8 7 5 6

6 3 2 1 3 7

0.016.0866.4/10
BATTERY

I014 I012 H010 I011

0.010.4516.3

1 2 D047
4 3 2 1 1 2

0.015.6123.4
N003

1 2

N006