Scribd
Upload
97 views3 pages

Camaro Tremec 6-Speed Fluid Change

This document provides instructions for draining and filling the transmission fluid on a 2016 Chevrolet Camaro with a Tremec 6-speed MM6 M13 manual transmission. The instructions include disconnecting components to access the drain and fill plugs, draining the fluid, filling to the proper level, reconnecting components, and checking the fluid level.

Uploaded by

liudas82
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
97 views3 pages

Camaro Tremec 6-Speed Fluid Change

This document provides instructions for draining and filling the transmission fluid on a 2016 Chevrolet Camaro with a Tremec 6-speed MM6 M13 manual transmission. The instructions include disconnecting components to access the drain and fill plugs, draining the fluid, filling to the proper level, reconnecting components, and checking the fluid level.

Uploaded by

liudas82
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

2016 Chevrolet Camaro | Camaro Service Manual 9128931 | | Manual Transmission - Tremec 6-Speed MM6 M13 |

Transmission Repair Instructions - On Vehicle |


Document ID: 4039478

Transmission Fluid Drain and Fill (MM6)


Draining Procedure

1. Raise and suitably support the vehicle. Lifting and Jacking the Vehicle
2. Place a suitable drain pan under the transmission.

3. Disconnect the electrical connector from the transmission fluid temperature sensor/drain plug (1).
4. Remove the transmission fluid temperature sensor/drain plug (1).
5. Allow the system to drain.
6. Apply sealant to the transmission fluid temperature sensor/drain plug (1). Adhesives, Fluids, Lubricants, and Sealers
Caution: Refer to Component Fastener Tightening Caution.
7. Install the transmission fluid temperature sensor/drain plug (1) and tighten to 27 Y (20 lb ft).
8. Connect the electrical connector to the transmission fluid temperature sensor/drain plug.

Filling Procedure

© 2017 General Motors. All rights reserved.


1. Disconnect the clip (1) retaining the cooler pipe to the transmission bracket.
2. Reposition the cooler pipe to allow access to the fill plug.
3. Remove the transmission fluid fill plug.
Important: Transmission fluid level setting must be followed exactly as written or the transmission may be overfilled or under
filled.
4. For fluid recommendations, Refer to Adhesives, Fluids, Lubricants, and Sealers.
Transmission fluid level MUST be 3.2 mm (1/8 inch) below (1) the fill plug. This can be done by one of the following two methods:
Bend mechanics wire to 3.2 mm (1/8 inch) to check fluid level. Add or remove fluid as necessary.
Fill transmission until level with the bottom of the fill plug hole, then remove 240 ml (8 ounces) of fluid.
5. Apply sealant to the transmission fill plug (1). Adhesives, Fluids, Lubricants, and Sealers

Caution: Refer to Fastener Caution.


6. Install the transmission fill plug to the transmission and tighten the fill plug to 27 Y (20 lb ft).
Note: Inspect the clip for proper retention on the cooler line to the bracket. Replace the clip as necessary.
7. Reconnect the clip (1) retaining the cooler pipe to the transmission bracket.
Note: Ensure the clutch pedal is NOT depressed.
8. Run the engine in Neutral for two minutes to allow the fluid to recirculate.
9. Remove the fill plug and verify the fluid level is 3.2 mm (1/8 inch) below the fill plug hole. Add or remove transmission fluid as
necessary.
10. Install the transmission fill plug to the transmission and tighten the fill plug to 27 Y (20 lb ft).
11. Lower the vehicle.

You might also like