Track-Type Tractor TA1
TA1 0 0 54 3
Nomor Inspeksi 14491311 Nama Pelanggan PT. Semarak Tambang
Nusantara
Nomor Seri XPC00791 Perintah Kerja 8600634214
Membuat CATERPILLAR Selesai Pada 06/10/2023 10.21.24
Model D6GC Inspektur Sadli Rais Junus
Keluarga Peralatan TRACK-TYPE TRACTOR PDF Dihasilkan Pada 06/10/2023
SMU 215 Jam Lokasi Moronopo
Koordinat 0, 0, 0
Technician
General Info & Comments
General info/Comments NORMAL
Prepare Machine
1.1 Check with customer for operator complaints NORMAL
1.2 Perform machine inspection preparation NORMAL
1.3 Perform Site Safety and Pre-Start Inspection COMPLETE
1.4 Download machine fault codes PASS
1.5 Check Product Link YES
1.6 Observe engine exhaust colors NORMAL
1.7 Listen for unusual noises NORMAL
Lower-Level Inspection
2.1 Final drives and sprockets NORMAL
2.2 Carrier rollers NORMAL
Form Order Report Serial Number : XPC00791 Page 1 of 4
2.3 Track rollers NORMAL
2.4 Track roller bogies NORMAL
2.5 Front and rear idlers NORMAL
2.6 Track guides NORMAL
2.7 Track shoes NORMAL
2.8 Track links, pins, and bushings NORMAL
2.9 Track roller frame NORMAL
2.10 Equalizer bar NORMAL
2.11 Pivot shaft NORMAL
2.12 Bottom Guard NORMAL
Middle-Level Inspection
3.1 Steps and Handrails NORMAL
3.2 Work Lights NORMAL
3.3 Hood and Platform NORMAL
3.4 Cooling Fan, Fan Guard and Shroud NORMAL
3.5 Radiator, Aftercooler, Oil Cooler & Condenser NORMAL
3.6 Radiator Cap NORMAL
Form Order Report Serial Number : XPC00791 Page 2 of 4
3.7 Upper and Lower Radiator Lines, Air Inlet Lines and Aftercooler Lines NORMAL
3.8 Precleaner and Air Cleaner NORMAL
3.9 Cylinder Head and Valve Cover NORMAL
3.10 Turbocharger NORMAL
3.11 Exhaust Manifold NORMAL
3.12 Pulleys, Belts, Compressor Clutch and Alternator NORMAL
3.13 JW Water Pump NORMAL
3.14 Engine wiring harness NORMAL
3.15 Fuel Lines, Fuel Pump and Fuel Filter Base NORMAL
Upper-Level Inspection
4.1 Cab Exterior NORMAL
4.2 Cab Interior NORMAL
4.3 Battery & Cables NORMAL
4.4 Power train and hydraulic oil filter compartment NORMAL
4.5 Hydraulic Tank NORMAL
4.6 Backup Alarm PASS
Implement/Attachment Inspection
5.1 Blade and trunnion ball joints, stabilizer bar, tilt and angle cylinders NORMAL
Form Order Report Serial Number : XPC00791 Page 3 of 4
5.2 Blade lift cylinder NORMAL
5.3 Blade cutting edges and end bits NORMAL
5.4 Ripper N/A
5.5 Ripper cylinders N/A
Site Conditions
6.1 Ambient Temperature in Engine Room NORMAL
6.1.1 (90° to 115°F or 0° to -20°F) - ACTION: Above 46°C or Below -29°C
(Above 115° or Below -20°F)
6.2 Altitude NORMAL
6.3 Haul Road Grade NORMAL
6.4 Haul Road Condition NORMAL
6.5 Humidity NORMAL
6.6 Air Quality NORMAL
6.7 Underfoot Condition NORMAL
6.8 Machine Utilization NORMAL
6.9 Equipment Role .
6.10 Working Material NORMAL
6.11 Maintenance Practices NORMAL
Form Order Report Serial Number : XPC00791 Page 4 of 4
