Technical Data Sheet
^(ValidationDate) 6341 6341 5 1
MY - SG - VN Approved Other
Jotasealer 03
Product description
Type
A modified acrylic water based sealer with good adhesion and alkali resistance for interior walls.
Features and benefits
Good Adhesion – Improve bonding between topcoat and concrete surface allowing finishing paint to adhere
better than if used alone.
Alkali Resistance – Seals off substrate to resist alkaline and moisture attack to prevent overall deterioration of
paint film.
Formulated without Harmful Chemicals - 100% Free from harmful chemicals such as APEO, formaldehyde,
heavy metals and has low volatile organic compound (VOC).
Recommended use
For interior application, suitable for new buildings and repainting.
Substrate
On concrete, masonry, plaster, brick work and soft board surfaces.
Product data
Packaging size Packing may vary from country to country according to local requirements.
Colours White.
Solids by volume 35 ± 2 volume%
Flash point Closed cup: Not applicable.
Application data
Remarks
Handle with care. Stir well before use.
Application equipment / methods
By brush, roller, airless spray or conventional spray.
Guiding data for airless spray
Nozzle tip 0.021" - 0.027"
Spray angle degrees 65°-80°
Pressure at nozzle 140 - 190 kg/cm² (2100 psi)
Date of issue: 19.12.2016 Product code: 6341 Page: 1/3
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) for this product.
For your nearest local Jotun office, please visit our website at www.jotun.com.
1
Technical Data Sheet
Jotasealer 03
Spreading rate per coat
Theoretical 8,7 m²/l - 11,7 m²/l
Spreading rate depends on film thickness applied, type of texture, surface porosity, imperfections, temperature,
wastage during painting etc.
Recommended film thickness per coat
Wet 85 µm - 111 µm
Dry 30 µm - 40 µm
Film thickness will vary and are calculated as an average.
Thinner
Water
Dilution
The paint is ready to use after proper stirring. If thinning is required, water may be added up to a maximum of
5%.
Conditions during application
The temperature of the substrate should be minimum 10 °C and at least 3 °C above the dew point of the air,
measured in the vicinity of the substrate. Good ventilation is usually required in confined areas to ensure proper
drying.
Drying times
Drying times are generally related to air circulation, temperature, film thickness and number of coats, and will
be affected correspondingly. The figures given in the table are typical with:
Good ventilation (Outdoor exposure or free circulation of air)
Typical film thickness
One coat on top of inert substrate
The given data must be considered as guidelines only. The actual drying time and time before recoating may be
shorter or longer, depending on the ambient temperature, film thickness, ventilation, humidity, underlying paint
system, requirement for early handling and mechanical strength etc.
1. Recommended data given is, for recoating with the same generic type of paint.
2. In case of multi-coat application, drying times will be influenced by the number and sequence and by the
total thickness of previous coats applied.
3. The surface should be dry and free from any contamination prior to application of the subsequent coat.
The drying time is measured by stated values
Relative Humidity (RH) 50 %
Substrate temperature 10 °C 23 °C 40 °C
Surface (touch) dry 2h 1h 0.5 h
Hard dry 8h 6h 4h
Dry to over coat, minimum 4h 2h 1h
Directions for use
Surface preparation
The substrate must be sound, clean, dry and free from dust, oil, grease, laitance etc. All traces of form release
agents/curing agents must be removed. A light sanding with suitable abrasive material is recommended before
application. Any resulting dust/loose particles must be removed.
Recommended paint system
Date of issue: 19.12.2016 Product code: 6341 Page: 2/3
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) for this product.
For your nearest local Jotun office, please visit our website at www.jotun.com.
1
Technical Data Sheet
Jotasealer 03
Primer
Jotasealer 03 : 1 coat
Topcoat
Strax or Jotaplast : 2 coats
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.
Certificates
Complies to Singapore Green Label and Malaysia Eco-Sirim Label.
Health and safety
Please observe the environmental and precautionary notices displayed on the container.
A Material Safety Data Sheet for the product has been issued.
Detailed information regarding health and safety risks and precautions for the use of this product is specified in
the product's Safety Data Sheet.
First-aid measures, refer to section 4.
Handling and storage, refer to section 7.
Transport information, refer to section 14.
Regulatory information, refer to section 15.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.
Date of issue: 19.12.2016 Product code: 6341 Page: 3/3
This Technical Data Sheet supersedes those previously issued.
The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) for this product.
For your nearest local Jotun office, please visit our website at www.jotun.com.
