Level 1 Quiz
1. From which direction does Autocad start measuring angles?
a) 12 o’clock
b) 3 o’clock
c) 6 o’clock
d) 9 o’clock
2. What does WCS stand for?
a) western cad system
b) Worldwide coordinate sectors
c) World coordinate system
d) Wrong cad settings
3. When drawing in 2D, what axis do you NOT work with
a) X
b) Y
c) Z
d) WCS
4. Is 300 degrees the same as -60 degrees in a drawing?
a) Yes
b) No
c) Not always
d) Never
5. Which one of these will NOT start the print command?
a) typing PLOT
b) Typing PRINT
c) Pressing Control+P
d) Pressing AlT+P
6. What should you pay attention to when learning AutoCAD?
a) the command Line
b) The status bar
c) The title bar
d) Tool icon
7. Polar coordinates are used mostly for drawing ?
a) Circls
b) Arcs
c) Vertical lines
d) Angled lines
8. Which keystrokes will UNDO a command?
a) control+U
b) Alt+U
c) Control+Z
d) Alt+Z
9. When using the TRIM command, which do you select first ?
a) the cutting edges
b) The object to be trimmed
c) Everything
d) Nothing
10. How many snap points does an object have?
a) One
b) Two
c) Depends upon the object
d) At least four
11. How many points do you need to define for the rectangle command?
a) one
b) Two
c) Four
d) None
12. How many Autocad objects are in a rectangle?
a) None
b) One
c) Four
d) Right
13. If you draw a line a 270 degrees, it will point?
a) up
b) Down
c) Left
d) Right
14. How long will a line from 1.4 to 4.4 be?
a) four units
b) Eight untis
c) Cant tell from those coordinates
d) Three units
15. How long will line from 1.4 to @4<5 be ?
A) three units
B) Four units
C) Five units
D) 3.5467 units
16. How many points do you need to draw a line using absolute coordinates?
A) none
B) One
C) Two
D) Four
17. When selecing objects. Pressing’L’ will :
A) select lines only
B) Select objects when you move your mouse to the left
C) Select the last object you created
D) Select the last object you modified
18. Pressing shifts while you are selecting will?
A) allow you to draw a window
B) Automatically delete the object(s)
C) Remove the next selected object from the set
D) Highlight the selected objects
19. Pressing “F” when selecting objects will....
A) Allow you to draw a fence
B) Finish the selection set
C) Limit you to five objects
D) Allow you to find specific object
20. How you select the last set of object(s) you selected?
(A) Type ‘L’
(B) Type ‘P’
(C) Type ‘H’
(D) You can not do this
21. What is the best way of drawing a rectangle?
(A) Using the Line command
(B) Using the polyline command
(C) Using the rectangle command
(D) Using the multiline command
22.. To move something four untis to the right, what would be the 2nd point of
displacement?
(A)@4,0
(B)@4<0
(C)Neither 1 nor 2
(D)Both 1 and 2
23. How should you select objects when using the stretch command?
(A) With a crossing window
(B) Pick them one by one
(C) Hold the shift key while selecting
(D) Type ‘S’
24. The origin of a drawing is at:
(A) The first point you select
(B) 0,0
(C) A random point in space
(D) 10,10
25. Objects are rotated around the..
(A) Base point
(B) Bottom right of the object
(C) Centre of the object
(D) Origin
26. The fillet command creates:
(A) Sharp corners
(B) Round corners
(C) A circle
(D) A boneless fish
27. A polar array creates new objects...
(A) In a grid pattern
(B) In a straight line
(C) In a circular pattern
(D) In an northern pattern
28. The distances of a chamber are:
(A) Always different
(B) Always the same
(C) Sometimes different
(D) Never the same
29. You should use Osnaps when you dimension...
(A) Never
(B) Always
(C) Only on lines
(D) Only on arcs and circles
30. How many layers should a drawing have?
(A) One
(B) Ten
(C) One for each project
(D) As many as are needed to clearly display the objects
31. When can you change the height of your text?
(A) Only when you start the drawing
(B) Only in a special text dialog box
(C) When you are starting the Text command
(D) You can’t, it is pre-set by AutoCAD
32. Scaling objects makes them...
(A) Bigger
(B) Smaller
(C) It only stretches them.
(D) Both Bigger and Smaller
33. Which layer(s) will you most likely needed?
(A) At least one for the objects
(B) Text
(C) Dimension
(D) All of the above
34. What can be contained in a template drawing?
(A) Layers
(B) Text Styles
(C) Dimension styles
(D) All of the above
35. To invoke the Zoom command transparently, type:
(A) ‘Z
(B) >Z
(C) :Z
(D) “Z
36. Which is not a valid Zoom option?
(A) Zoom Extents
(B) Zoom Previous
(C) Zoom Next
(D) Zoom Window
37. Panning allows you to...
(A) Minimize the drawing
(B) See all of the drawing at once
(C) Close in on a small area
(D) Move around the drawing at the same scale
38. Why should you use the Zoom tools?
(A) To be more accurate
(B) To be faster
(C) To make your life easier
(D) All of the above
39. What can you type in to see the text styles dialog box?
(A) Text
(B) Text Styles
(C) TS
(D) ST
40. What can be a problem with using True Type fonts?
(A) They can slow down the drawing
(B) Other users may not have the same fonts
(C) They can be tougher to format
(D) All of the above
41. Why should you not use the standard TXT font?
(A) It’s ugly
(B) It looks unprofessional
(C) It can be difficult to read
(D) All of the above
42. When you are defining a Text Style, should you adjust the height?
(A) Always
(B) Never
(C) Only if you really know what you’re doing
(D) Sometimes
43. When you are in Paper Space (layout), what do you draw to see your model?
(A) A window
(B) A box
(C) A rectangle
(D) A viewport
44. What’s the easiest way to know if you are in paper space/layout mode?
(A) Zoom out
(B) Ask someone
(C) Look for the triangular icon
(D) Try printing
45. What command do you use to scale a viewport?
(A) Scale
(B) VPscale
(C) Print
(D) Zoom
46. Should you modify your model in Paper Space / Layout Mode?
(A) Never
(B) Always
(C) Yes, because i like to learn bad habits
(D) Only when i’m being lazy
47. What is an advantage to using blocks in your drawing
(A) It keeps file size down
(B) They are easier to modify
(C) They can contain attributes
(D) All of the above
48. When creating a block, what don’t you need to do?
(A) Give it a name
(B) Select the objects
(C) Add attributes
(D) Pick a base point
49. Once you create a block, can you change it?
(A) You can redefine it
(B) Never
(C) Only if you didn’t name it
(D) You can only resize (scale) it
50. What command do you use to write a block to a separate file?
(A) Blockwrite
(B) WBlock
(C) You cannot write a block to a disk
(D) Writer’s block
