R&S®NGP800

POWER SUPPLY SERIES

year

Boost your efficiency with quadcore power

Data Sheet
Version 01.00
AT A GLANCE
Comprising five powerful models
The R&S®NGP800 DC power supply series, comprising five An intuitive operating concept and a large touchscreen
models with 400 W or 800 W, provides maximum power ­allow you to enter values much faster and to display statis-
at a variety of operating points. The two or four 200 W out- tics in realtime.
puts can each supply up to 64 V or up to 20 A. Electrically
equivalent and galvanically isolated outputs can be wired All R&S®NGP800 power supplies include remote sense ter-
in series or parallel for up to 250 V or 80 A. minals, USB and a LAN interface. A user-installable GPIB
interface, a digital trigger I/O, an analog input and a wire-
Synchronizing your outputs, performing waveform tests less LAN interface are optional, making these instruments
and logging data for in-depth analysis – all this becomes great on the bench or in an automated test system.
easy with the R&S®NGP800 power supply series.

R&S®NGP802
►► Two-channel power supply
►► 400 W – 2 × 32 V/20 A

R&S®NGP804
►► Four-channel power supply
►► 800 W – 4 × 32 V/20 A

R&S®NGP814
►► Four-channel power supply
►► 800 W – 2 × 32 V/20 A
2 × 64 V/10 A

R&S®NGP822
►► Two-channel power supply
►► 400 W – 2 × 64 V/10 A

R&S®NGP824
►► Four-channel power supply
►► 800 W – 4 × 64 V/10 A

2
BOOST YOUR EFFICIENCY WITH ...
... full flexibility ... full safety
►► 5" high-resolution touch display ►► Protection functions
►► FlexPower ►► Safety limits
►► Four power supplies in a single instrument ►► Safe working environment
►► Parallel and serial operation ▷▷ page 8
▷▷ page 4
... full connectivity
... full functionality ►► Digitalremote control
►► Ramp function ►► Digitaltrigger I/O
►► Output delay ►► Analog input
►► Arbitrary function ▷▷ page 9
►► Remote sensing
►► Built-in measurements
►► Data logging
▷▷ page 6

Different classes of power supplies

Basic power supplies

►► Economical, quiet and stable instruments
►► For manual and simple computer-controlled operation
►► In applications where speed and accuracy are a low
consideration
►► Used in education, on the bench and in system racks

R&S®HMC8043 and R&S®NGE103B

three-channel power supplies

Performance power supplies

►► When speed, accuracy and advanced programming features are
factors in test performance
►► Features such as DUT protection, fast programming times and
downloadable V and I sequences
►► Used in labs and ATE applications

R&S®HMP4040 and R&S®NGP804 four-

channel power supplies

Specialty power supplies

►► Tailored to specific applications
►► Unique features such as
–– Emulation of the unique characteristics of a battery

–– Electronic loads to accurately sink current and dissipate power in a controlled manner

►► Used in labs and ATE environments

R&S®NGL201 single-channel and

R&S®NGM202 two-channel power supply

Basic class Performance class Specialty class

Rohde & Schwarz R&S®NGP800 Power Supply Series 3

FULL FLEXIBILITY
5" high-resolution touch display
The large high-resolution touch display
makes operation easy. Quickly navigate
through the menus to access all func-
tions and settings. Enter values much
faster using the virtual keyboard instead
of turning the knob.

The home screen gives you a clear over-

view of all your channels. Each channel
can be selected for a more detailed view
with a wide variety of additional informa-
tion, such as statistics and icons indicat-
ing the status of set protection or special
functions.

FlexPower
Get the maximum power at various
­operating points. Unlike with single
range power ­supplies, you can gener-
ate variable voltage and current combi-
nations within the overall power limit of
200 W per channel.

32 V output
25
Current in A

20
64 V output
15 15
Current in A

10 10

5 5

0 0
0 20 40 0 20 40 60 80
Voltage in V Voltage in V

4
 Four power supplies in a single instrument
Save costs and space on your bench or in your rack by powering up to four DUTs with a single
­instrument. Each output is completely independent and floating.

All outputs can operate in constant voltage (CV) or constant current (CC) mode with automatic
crossover and mode indication.

A separate output button allows you to synchronously switch all channels on or off. This is crucial
for circuitries that can be damaged if one voltage rail is pres­ent without the other. The individual
channel buttons let you select the chan­nels you want to operate.

+ + +

CH1 CH2 CH3 CH4

Parallel and serial operation

Parallel and serial operation

SAT TV In case your application requires more
voltage or cur­rent, connect the outputs
in series or parallel and get up to 250 V
(R&S®NGP824) or 80 A (R&S®NGP804)
– giving you the flexibility you always
asked for. Using the tracking function,
Parallel operation – max. 80 A
voltage and current are adjusted on all
selected channels simultaneously.

Serial operation – max. 250 V

Rohde & Schwarz R&S®NGP800 Power Supply Series 5

FULL FUNCTIONALITY
Ramp function (EasyRamp) Output delay
To control inrush currents, some test set- Turn on each channel individually with a
ups require the continuous rise of the ­delay to meet the requirements of state-
supply voltage instead of a rapid jump. of-the-art microcontrollers that use multi-
Increase the output voltage continuously ple ­supply voltages and demand specific
within a timeframe of 10 ms to 60 s with power-up sequences.
the EasyRamp function.

QuickArb function
Voltage

Voltage

Time Time
File #1 File #2
Voltage

Dwell time

End behavior

Time
File #1 File #2 File #3
reps:3 reps:1 reps:3
Sequence
max. 1024 points

Up to eight files
Voltage

…
Time
File #3 File #… File #…

6
Arbitrary function (QuickArb) Data logging
Emulate the normal behaviors of your Logging data is key to long-term moni-
power subsystems early in the design toring, reviewing test setups and re-
process and simulate power problems peating test conditions when analyzing
for DUT design verification. power behaviors or optimizing power
consumption.
The QuickArb function lets you gener­ate
voltages that vary over time and current The R&S®NGP800 power supplies si-
sequences of output changes with dwell multaneously log voltage and current
times down to 1 ms. Load up to eight measurements over time on all outputs.
subgroup files into one sequence to cre- You can easily export the timestamped
ate complex patterns. data as a .CSV file for reports and
documentation.

Remote sensing
Improve your voltage regulation using Save/recall device settings
remote sensing, regulating the output Continue exactly where you left off last
voltage directly at the DUT input termi- time and avoid frustration when sev-
nals instead of the power supply’s output eral persons use the same power sup-
terminals. ply. Save frequently used settings with
the save function. The recall function lets
The four-wire remote sensing com- you load files to any R&S®NGP800 power
pensates for voltage drops in the sup- supply to ensure the same setup on mul-
ply leads especially in applications with tiple instruments.
high currents. The R&S®NGP800 power
supplies provide sense connections for
each output at both the front and rear
terminals. User button
Configure the user button with a fre-
quently used action to easily access it at
the press of a button. Choose between
Built-in measurements screenshot, toggle logging, reset statis-
The built-in measurements reduce the tics and TouchLock.
need for an external multimeter and
simplify the setup. The separate voltage
and current meters on each output give
a resolution of 1 mV and 0.5 mA over User adjustment
the full output range of 64 V and 20 A, Immensely reduce your downtime by
respectively. calibrating your R&S®NGP800 power
supply in-house. All you need is a stan-
dard 6½ digit DMM, a 10 mΩ shunt re-
sistor and one minute per channel.

Rohde & Schwarz R&S®NGP800 Power Supply Series 7

FULL SAFETY
Protection functions
Protecting your DUT is crucial to limit testing. The R&S®NGP800 power supplies include overcurrent protection (OCP),
overvoltage protection (OVP) and overpower protection (OPP).

The internal overtemperature protection (OTP) switches the power supply off if a thermal overload is imminent.

You can set the maximum current, voltage and power separately for each channel. If an active protection function trips,
you are alerted by a beeping sound and the corresponding symbol flashing on the status bar.

Overcurrent protection Safety limits

(OCP, electronic fuse) To be sure to protect the device under
Adjust the sensitivity and response be- test, you can set safety limits to restrict
havior of the electronic fuse according the power supply to values that are not
to your application. The fuse delay at dangerous for your DUT.
output-on specifies how long the fuse
remains inactive after the channel is
switched on. The sensitivity of the fuse is
specified by the fuse delay time. Safe working environment
To eliminate unnecessary noise, the
The FuseLink function allows you to link R&S®NGP800 power supplies automati-
the fuses between channels, switching cally adjust fan speed to the load con-
off all linked channels as soon as the se- dition, allowing you to work in a quiet
lected channel reaches the current limit. environment.

The R&S®NGP800 power supplies use

4 mm banana safety plugs, as required
Overvoltage protection (OVP) by an increasing number of laboratories
If the voltage exceeds your set maximum for safety reasons.
value, the channel is switched off.

Overpower protection (OPP)

Instead of the maximum voltage, you
can use the maximum power as the
switch-off criterion.

8
FULL CONNECTIVITY
Digital remote control Digital trigger I/O (R&S®NGP-K103 option)
To meet the requirements of varying Configure the eight pins of the digital I/O
environments, an array of interfaces connector as inputs or outputs to gen-
to remotely control your instrument is erate trigger events for output control
provided. and indication. As an input, the trigger
I/O can enable or inhibit outputs or start
USB and LAN (Ethernet) are standard, functions such as QuickArb or logging.
while the wireless LAN and IEEE-488 As an output, the trigger I/O can indicate
(GPIB) interfaces are optional and can protection triggers, voltage/current/pow-
also be added at a later date. er level events and actual output operat-
ing modes.
The additional output and sense termi-
nals on the rear panel allow easy wiring In addition, the digital trigger system al-
and make the R&S®NGP800 power sup- lows you to control output delays or fuse
ply series a good choice for both your linking across multiple instruments.
bench and your automated test system.

Analog input (R&S®NGP-K107 option)

Control the output voltages and currents
directly and much faster. An external
control voltage from 0 V to 5 V can con-
trol any or all of the outputs with an in-
put scaling from 0 % to 100 %.

Galvanic isolation between the control

voltage and the outputs greatly simplifies
the connection while maintaining user
safety even for high-voltage and floating-
circuit applications.

For easier access, the R&S®NGP800 power supplies come with pluggable 8-pin terminal blocks for the rear output connections, digital trigger I/O and analog input connections

Rohde & Schwarz R&S®NGP800 Power Supply Series 9

SPECIFICATIONS
Definitions

General
Product data applies under the following conditions:
►► Three hours storage at ambient temperature followed by 30 minutes warm-up operation
►► All data is valid at 23 °C (–3 °C/+7 °C) after 30 minutes warm-up time.
►► Specified environmental conditions met
►► Recommended calibration interval adhered to
►► All internal automatic adjustments performed, if applicable

Specifications with limits

Represent warranted product performance by means of a range of values for the specified parameter. These specifications are marked with limiting
­symbols such as <, ≤, >, ≥, ±, or descriptions such as maximum, limit of, minimum. Compliance is ensured by testing or is derived from the design.
Test limits are narrowed by guard bands to take into account measurement uncertainties, drift and aging, if applicable.
Y-axis

Specification limit

Actual values with measurement uncertainty and guard band

Specification limit

X-axis
Measurement uncertainties Guard band

Specifications without limits

Represent warranted product performance for the specified parameter. These specifications are not specially marked and represent values with no or
negligible deviations from the given value (for example, dimensions or resolution of a setting parameter). Compliance is ensured by design.

Typical data (typ.)

Characterizes product performance by means of representative information for the given parameter. When marked with <, > or as a range, it represents
the performance met by approximately 80 % of the instruments at production time. Otherwise, it represents the mean value.

Nominal values (nom.)

Characterize product performance by means of a representative value for the given parameter (for example, nominal impedance). In contrast to typical
data, a statistical evaluation does not take place and the parameter is not tested during production.

Measured values (meas.)

Characterize expected product performance by means of measurement results gained from individual samples.

Uncertainties
Represent limits of measurement uncertainty for a given measurand. Uncertainty is defined with a coverage factor of 2 and has been calculated in line
with the rules of the Guide to the Expression of Uncertainty in Measurement (GUM), taking into account environmental conditions, aging, wear and tear.

Device settings and GUI parameters are indicated as follows: “parameter: value”.

Typical data as well as nominal and measured values are not warranted by Rohde & Schwarz.

In line with the 3GPP/3GPP2 standard, chip rates are specified in Mcps (million chips per second), whereas bit rates and symbol rates are specified in
Mbps (million bits per second), kbps (thousand bits per second), Msps (million symbols per second) or ksps (thousand symbols per second), and sample
rates are specified in Msample/s (million samples per second). Mcps, Mbps, Msps, kbps, ksps and Msample/s are not SI units.

10
Electrical specifications
Outputs The channel outputs are galvanically isolated and not connected to ground.
Number of output channels R&S®NGP802, R&S®NGP822 2
R&S®NGP804, R&S®NGP824, R&S®NGP814 4
Total output power R&S®NGP802, R&S®NGP822 max. 400 W
R&S®NGP804, R&S®NGP824, R&S®NGP814 max. 800 W
Maximum output power per channel 200 W
Output voltage per channel R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2) 0 V to 32 V
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4) 0 V to 64 V
Maximum output current per channel R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2) 20 A
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4) 10 A
Maximum voltage in serial operation R&S®NGP802 64 V
R&S®NGP822, R&S®NGP804, R&S®NGP814 128 V
R&S®NGP824 250 V
Maximum current in parallel operation R&S®NGP822 20 A
R&S®NGP802, R&S®NGP824, R&S®NGP814 40 A
R&S®NGP804 80 A
< 3 mV (RMS),
Voltage ripple and noise 20 Hz to 20 MHz
< 30 mV (Vpp) (meas.)
Current ripple and noise 20 Hz to 20 MHz < 3.5 mA (RMS) (meas.)
Load regulation load change: 10 % to 90 %
Voltage ±(% of output + offset)
R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2) < 0.01 % + 5 mV
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4) < 0.01 % + 10 mV
Current ±(% of output + offset) < 0.01 % + 5 mA
50 % to 100 % load change to within 0.2 % of rated
Load recovery time < 400 µs (meas.)
voltage
Rise time 10 % to 90 % of rated output voltage, resistive load
R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2) < 10 ms
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4) < 12 ms
Fall time 90 % to 10 % of rated output voltage, resistive load
R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2) full load: < 10 ms, no load: < 50 ms
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4) full load: < 25 ms, no load: < 50 ms
Programming resolution
Voltage 1 mV
Current 0.5 mA
Programming accuracy
Voltage ±(% of output + offset)
R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2) < 0.05 % + 5 mV
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4) < 0.05 % + 10 mV
Current ±(% of output + offset)
R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2) < 0.1 % + 20 mA
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4) < 0.1 % + 10 mA

Rohde & Schwarz R&S®NGP800 Power Supply Series 11

Output measurements
Measurement functions voltage, current, power, energy
Readback resolution
Voltage 1 mV
Current 0.5 mA
Readback accuracy
Voltage ±(% of output + offset)
R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2) < 0.05 % + 5 mV
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4) < 0.05 % + 10 mV
Current ±(% of output + offset)
R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2) < 0.1 % + 20 mA
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4) < 0.1 % + 10 mA
Temperature coefficient (per °C) ±(% of output + offset), +5 °C to +20 °C and +30 °C to +40 °C
voltage: < 0.0075 % + 0.75 mV,
R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2)
current: < 0.015 % + 3 mA
voltage: < 0.0075 % + 1.5 mV,
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4)
current: < 0.015 % + 1.5 mA
Remote sensing
Maximum sense compensation 1 V (meas.)

Ratings
Maximum voltage to ground 250 V DC
Maximum counter voltage voltage with the same polarity connected to the outputs
R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2) 35 V
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4) 70 V
Maximum reverse voltage voltage with opposite polarity connected to the outputs 0.4 V
Maximum reverse current for 5 min max. 20 A

Remote control
Command processing time < 30 ms (typ.)

Protection functions
Overvoltage protection adjustable for each channel
Programming resolution 1 mV
Overpower protection adjustable for each channel
Overcurrent protection (electronic fuse) adjustable for each channel
Programming resolution 0.5 mA
Response time (Iload > Iresp × 2) at Iload ≥ 2 A < 1 ms
Fuse linking (FuseLink function) yes
Fuse delay at output-on adjustable for each channel 10 ms to 10 s (1 ms increments)
Response time for linked channels < 5 ms
Fuse delay time adjustable for each channel 10 ms to 10 s (1 ms increments)
Overtemperature protection independent for each channel

12
Special functions
Output ramp function EasyRamp
EasyRamp time 10 ms to 60 s (1 ms increments)
Output delay
Synchronicity < 1 ms (typ.)
Delay per channel 10 ms to 10 s (1 ms increments)
Arbitrary function QuickArb
Parameters voltage, current, time
Maximum number of points 1024
Maximum number of subgroups 8
Dwell time 1 ms to 60 s (1 ms increments)
continuous or burst mode with
Repetition
1 to 65535 repetitions
manually, by remote control or via optional
Trigger
­trigger input
Trigger and control interfaces R&S®NGP-K103 digital I/O, 16-pin connector block
Trigger response time < 3 ms (typ.)
Maximum voltage (IN/OUT) 5.5 V
Input trigger level TTL
Maximum drain current (OUT) 5 mA
Analog control interface R&S®NGP-K107 analog input, 16-pin connector block
Input voltage 0 % to 100 % control of voltage or current 0 V to 5 V
voltage: < 0.1 % + 16 mV,
Output accuracy R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2)
current: < 0.1 % + 30 mA
voltage: < 0.1 % + 32 mV,
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4)
current: < 0.1 % + 15 mA
Temperature coefficient (per °C) ±(% of output + offset), +5 °C to +20 °C and +30 °C to +40 °C
voltage: < 0.015 % + 2.4 mV,
R&S®NGP802, R&S®NGP804, R&S®NGP814 (CH1, CH2)
current: < 0.015 % + 4.5 mA
voltage: < 0.015 % + 4.8 mV,
R&S®NGP822, R&S®NGP824, R&S®NGP814 (CH3, CH4)
current: < 0.015 % + 2.25 mA
Update rate 1 ms
Data logging
Maximum acquisition rate 125 sample/s
Memory depth external memory size
Voltage resolution see readback resolution
Voltage accuracy see readback accuracy
Current resolution see readback resolution
Current accuracy see readback accuracy

Display and interfaces

Display TFT 5" 800 × 480 pixel WVGA touch
4 mm safety sockets (channel outputs, remote
Front panel connections
sensing)
8-pin connector block
Rear panel connections R&S®NGP802, R&S®NGP822
(channel outputs and remote sensing)
2 × 8-pin connector block
R&S®NGP804, R&S®NGP824, R&S®NGP814
(channel outputs and remote sensing)
Remote control interfaces standard USB-TMC, USB-CDC (Virtual COM), LAN
R&S®NGP-K102 WLAN
R&S®NG-B105 IEEE-488 (GPIB)

Rohde & Schwarz R&S®NGP800 Power Supply Series 13

General data
Environmental conditions
Temperature operating temperature range +5 °C to +40 °C
storage temperature range –20 °C to +70 °C
Humidity noncondensing 5 % to 95 %
Power rating
Mains nominal voltage 100 V to 250 V
Mains frequency 50 Hz to 60 Hz
Maximum power consumption R&S®NGP802, R&S®NGP822 650 W
R&S®NGP804, R&S®NGP824, R&S®NGP814 1125 W
Main fuses internal (not user accessible) 16 A 250 V IEC 60127-2/7 fast acting
Product conformity
applied standards:
►► ETSI EN 300328 V2.1.1
►► EN 61326-1
EU: in line with
Electromagnetic compatibility ►► EN 55011 (Class A)
Radio Equipment Directive 2014/53/EU
►► EN 55032 (Class A)
►► ETSI EN 301489-1 V2.2.0
►► ETSI EN 301489-17 V3.2.0
Korea KC mark
USA, Canada FCC47 CFR Part 15B, ICES-003 Issue 6
EU: applied harmonized standards:
Electrical safety
in line with Low Voltage Directive 2014/35/EU EN 61010-1
USA, Canada UL61010-1, CSA C22.2 No. 61010-1
Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy,
WLAN approvals Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, CE0682
Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey,
United Kingdom
Singapore iMDA standards DB102020 (class A)
USA, Canada FCC, IC
RoHS in line with EU Directive 2011/65/EU EN 50581
Mechanical resistance
5 Hz to 55 Hz, 0.3 mm (peak-to-peak),
Vibration sinusoidal 55 Hz to 150 Hz, 0.5 g const.,
in line with EN 60068-2-6
8 Hz to 500 Hz, acceleration: 1.2 g (RMS),
random
in line with EN 60068-2-64
40 g shock spectrum, in line with
Shock
­MIL-STD-810E, method 516.4, procedure I
Mechanical data
362 mm × 100 mm × 451 mm
Dimensions W×H×D
(14.25 in × 3.94 in × 17.76 in)
Weight R&S®NGP802, R&S®NGP822 7.5 kg (16.5 lb)
R&S®NGP804, R&S®NGP824, R&S®NGP814 8.0 kg (17.6 lb)
Rack installation R&S®ZZA-GE23 19 in, 2 HU
Recommended calibration interval 1 year

14
ORDERING INFORMATION
Designation Type Order No.
Base unit
Two-channel power supply, 400 W, 32 V/20 A R&S®NGP802 5601.4007.05
Four-channel power supply, 800 W, 32 V/20 A R&S®NGP804 5601.4007.02
Four-channel power supply, 800 W, 2 5 32 V/20 A, 2 × 64 V/10 A R&S®NGP814 5601.4007.04
Two-channel power supply, 400 W, 64 V/10 A R&S®NGP822 5601.4007.06
Four-channel power supply, 800 W, 64 V/10 A R&S®NGP824 5601.4007.03
Accessories supplied
Set of power cables, terminal blocks, quick start guide
Hardware options
IEEE-488 (GPIB) interface R&S®NG-B105 5601.6000.02
Software options
Wireless LAN remote control R&S®NGP-K102 5601.6400.03
Digital trigger I/O R&S®NGP-K103 5601.6300.03
Analog input R&S®NGP-K107 5601.6200.03
System components
19" rack adapter, 2 HU R&S®ZZA-GE23 5601.4059.02

Warranty
Base unit 3 years
All other items 1) 1 year
Options
Extended warranty, one year R&S®WE1
Extended warranty, two years R&S®WE2
Extended warranty with calibration coverage, one year R&S®CW1 Please contact your local
Extended warranty with calibration coverage, two years R&S®CW2 Rohde & Schwarz sales office.
Extended warranty with accredited calibration coverage, one year R&S®AW1
Extended warranty with accredited calibration coverage, two years R&S®AW2

Extended warranty with a term of one and two years (WE1 and WE2)
Repairs carried out during the contract term are free of charge 2) Necessary calibration and adjustments carried out
­during repairs are also covered.

Extended warranty with calibration coverage (CW1 and CW2)

Enhance your extended warranty by adding calibration coverage at a package price. This package ensures that your
Rohde & Schwarz product is regularly calibrated, inspected and maintained during the term of the contract. It includes
all repairs 2) and calibration at the recommended intervals as well as any calibration carried out during repairs or option
upgrades.

Extended warranty with accredited calibration (AW1 and AW2)

Enhance your extended warranty by adding accredited calibration coverage at a package price. This package ensures
that your Rohde & Schwarz product is regularly calibrated under accreditation, inspected and maintained during the term
of the contract. It includes all repairs 2) and accredited calibration at the recommended intervals as well as any accredited
calibration carried out during repairs or option upgrades.

1)
For options that are installed, the remaining base unit warranty applies if longer than 1 year. Exception: all batteries have a 1 year warranty.
2)
Excluding defects caused by incorrect operation or handling and force majeure. Wear-and-tear parts are not included.

Rohde & Schwarz R&S®NGP800 Power Supply Series 15

 Rohde & Schwarz
Service that adds value The Rohde & Schwarz electronics group offers innovative
► Worldwide solutions in the following business fields: test and mea-
► Local und personalized surement, broadcast and media, secure communications,
► Customized and flexible cybersecurity, monitoring and network testing. Founded
► Uncompromising quality
► Long-term dependability more than 80 years ago, the independent company which
is headquartered in Munich, Germany, has an extensive
sales and service network with locations in more than
70 countries.

www.rohde-schwarz.com

Sustainable product design

►► Environmental compatibility and eco-footprint
►► Energyefficiency and low emissions
►► Longevity and optimized total cost of ownership

Certified Quality Management Certified Environmental Management

ISO 9001 ISO 14001

Rohde & Schwarz training

www.training.rohde-schwarz.com

Regional contact
►► Europe, Africa, Middle East | +49 89 4129 12345
customersupport@rohde-schwarz.com
►► North America | 1 888 TEST RSA (1 888 837 87 72)
customer.support@rsa.rohde-schwarz.com 3609192732

►► Latin America | +1 410 910 79 88

customersupport.la@rohde-schwarz.com
►► Asia Pacific | +65 65 13 04 88
customersupport.asia@rohde-schwarz.com
►► China | +86 800 810 82 28 | +86 400 650 58 96
customersupport.china@rohde-schwarz.com

R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG

3609.1927.32 01.00 PDP 1 en

Trade names are trademarks of the owners

PD 3609.1927.32 | Version 01.00 | December 2019 (gk/sk)
R&S®NGP800 Power Supply Series
Data without tolerance limits is not binding | Subject to change
© 2019 Rohde & Schwarz GmbH & Co. KG | 81671 Munich, Germany