Specifications

Photoelectric Sensor Type Through-Beam

Retro Reflective Diffuse Reflective

Cylindrical Type With polarizing filter Without polarizing filter 110mm type 400mm type 800mm type
Cable type C2TP-2000(N,P) C2RP-F400(N,P) C2RP-350(N,P) C2DP-11(N,P) C2DP-40(N,P) C2DP-80(N,P)
Plastic housing

C2 series
M12 Connector type C2TP-2000C(N,P) C2RP-F400C(N,P) C2RP-350C(N,P) C2DP-11C(N,P) C2DP-40C(N,P) C2DP-80C(N,P)
Cable type C2TM-2000(N,P) C2RM-F400(N,P) C2RM-350(N,P) C2DM-11(N,P) C2DM-40(N,P) C2DM-80(N,P)
Metal housing
M12 Connector type C2TM-2000C(N,P) C2RM-F400C(N,P) C2RM-350C(N,P) C2DM-11C(N,P) C2DM-40C(N,P) C2DM-80C(N,P)
Sensing Distance 20m 0.01 ∼ 4m (V-61) 0.01 ∼ 3.5m (V-61) 11cm ＊1 40cm ＊1 80cm ＊1
・C2DP- □□□・C2RP- □□□ Spot Size φ1100mm / 20m φ270mm / 4m φ240mm / 3.5m φ8mm / 11cm φ20mm / 40cm □30mm / 80cm
Light Source Red LED IR LED Red LED
・C2TP- □□□ Supply Voltage DC10 ∼ 30V including ripple (P-P) 10%
・C2DM- □□□・C2RM- □□□ Current Consumption
Emitter ：20mA max.
20mA max
Receiver ：15mA max.
・C2TM- □□□ Hysteresis - 10% max.

INSTRUCTION MANUAL
Response Time 0.5ms max.
Control Output NPN/PNP Open Collector 100mA max. / DC30V max. （Residual voltage max. 1.8V / 100mA max.）
Operation Mode Light ON / Dark ON selectable by control wires
• Confirm if the item meets your needs. Sensitivity Adjustment 1 turn pot.
• Before the use, you should first thoroughly read LED Indicator Output indicator (Orange LED) / Stability indicator (Green LED)
this manual and operate correctly as mentioned. Environmental illuminance Sunlight : 10,000 lux, Incandescent lamp : 3,000 lux max.
• You should keep this manual at hand for proper Vibration Resistance 10 ∼ 55Hz amplitude 1.5mm X Y Z each 2 hours
use. Shock Resistance 500m/s^2 (50G) X Y Z each 3 times
Operating / Storage Temperature Operating temperature -25 ∼ +55℃ ( no freezing ) / Storage temperature ：-30 ∼ +70℃
Carefully read and understand the safety precautions before operation.
Operating / Storare humidity Operating humidity 35 ∼ 85%RH / Storage humidity ：35 ∼ 95%RH
The important information is provided to protect your health and property.
Protection / Material IEC IP67(common to any type) Plastic housing ： PBT（glass included ）/ Metal housing ：BSBM、 Front Cover , Lens ：PMMA
Do not apply any other installing or operating procedure other than that
described in this manual. ＊1 White Paper 90%

Safety Precautions Input / Output Circuit Diagram Operating Chart

CAUTION • with the power on. Make sure to turn off the power before Emitter
It is dangerous to wire or attach/remove the connector

operation.
• Make sure to use the product with the protective cover
attached and closed.
• Installing in the following places may result in malfunction:
1. A dusty or steamy place
2. A place generating corrosive gas
3. A place directly receiving scattering water or oil.
4. A place suffered from heavy vibration or impact.
• The product is not designed for outdoor use.
• Do not use the sensor in transient state after power on
(approx. 100 ms).
• Do not wire with the high voltage cable or the power line.
Failure to do this will cause malfunction by induction or
damage.
• The sensor performance or digital display values may
depend on the individual units or the condition of detected
product.
• This product is not an explosion-proof construction.
Do not use the product under flammable, explosive gas or
liquid environment.
• Do not use the product in water.
• Do not disassemble, repair, or convert the product.
Failure to do this may cause failure, fire, or electric shock.
• Operate within the rated range.
Dimensions CAUTION
1. Metal housing ( Diffused , Retro Reflective, Through Beam(Receiver) ) ! Must not use this item as safety equipment for the
purpose of human body protection.
Set Up Torque
• Plastic housing models
Tightening torque needs to be under
1.5N·m(15kgf·cm).
• Metal housing models
Tightening torque needs to be under
20N·m(200kgf·cm).

Reflectors
• Type V-61 Standard for Retro type • Type P45A Optional Reflector
Sensing distance : 4m Sensing distance : 1.4m
2. Metal housing (Through Beam (Emitter) )

3. Plastic housing (Diffused , Retro Reflective. Through Beam (Receiver) ) • Type V-42 Optional Reflector
Sensing distance : 2.5m

(Unit : mm)

• Specifications and equipments are subject to change without any

prior notice.
4. Plastic housing (Through Beam(Emitter)) • For more information, questions and comments regarding products,
contact authorized distributors of us.

Manufactured and sold by :

OPTEX FA CO.,LTD.
600-8815 Kyoto, Shimogyo, Awata Chudoji 93, Japan
TEL. +81-(0)75-325-2920 FAX. +81-(0)75-325-2921

Website : http://www.optex-fa.com