ZINCTECT 1000 HA(S)

Technical Data

ZINCTECT 1000 HA(S) Kansai Paint Protective Coatings

Pre-construction Primer
GENERIC TYPE
DESCRIPTION Inorganic zinc rich shop primer for steel plates and shapes based on alkyl silicate binder and zinc
powder

RECOMMENDED USE Steel structure at marine or industrial severe corrosive environment

- No trouble in gas-cutting and welding
FEATURES
- Quick drying
- Excellent shop coat line applicability
- Excellent anti-corrosive performance
- Excellent resistance to weathering, resistance to oil and resistance to organic solvents and
heat resistance

PHYSICAL PROPERTIES
Coloｕr Grey
Ｆｉｎｉｓｈ Matt
Volume Solids 29 ％
0.41 kg/㎡ ａｔ
Typical Thickness Ｄry ： 17 microns / ｃｏａｔ
Theoretical Coverage 16.7 ㎡/L ａｔ 17 microns ＤＦＴ
*Practical coverage vary depending on loss factors.
Flash Point 10℃(Base)
Specific Gravity 1.3 g/cm3
VOC 572 g/L
Temperature Resistance Ｎｏｎ-ｃｏｎｔｉnｕｏｕｓ ： 500℃， Cｏｎｔｉnｕｏｕｓ ： 400℃
*These numerical values are subject to normal manufacturing tolerances，colours and testing variances．

SURFACE - All surfaces to be coated should be completely clean, dry and free from contamination.
Surface preparation method shall be in accordance with ISO 8504: 2000.
PREPARATION
- Remove salt and other water-soluble contaminants by fresh water.
- Remove oil and grease with suitable detergent or solvent (SSPC-SP-1).
- Remove rust, mill scale and other loose material completely by abrasive blasting (ISO
8501-1:2007 Sa 2 1/2 or SSPC SP-10).

APPLICATION
Application Conditions Ambient temperature shall be above 0℃ and relative humidity shall be above 50%. Surface
temperature shall be a minimum of 3℃ above dew point.
Adequate ventilation shall be provided in confined spaces to ensure proper drying

Mixing Stir each component with power agitator well before mixing. Then power mix two components.

Mixing ratio Liquid/Powder = 42.2/57.8 (by weight)

Induction Time Not required

Application Method Airless spray

Thinner : ZINCTECT 1000HA Thinner (0-20% by weight)
Nozzle pressure: Not less than 10MPa
Nozzle Tip : No.163-515～621
Brush
Thinner : ZINCTECT 1000HA Thinner (0-5% by weight)
Power mix thinner if required.

*Too much thinning results sagging and slower cure.

Page 1 of 2
 ZINCTECT 1000 HA(S)

Clean Up Clean all the equipment with thinner immediately after use.

Pot Life 5℃ 20 ℃ 30 ℃

24 ｈｏｕｒ(ｓ) 24 ｈｏｕｒ(ｓ) 24 ｈｏｕｒ(ｓ)

*Use all mixed paint within pot life.

Drying Time 5℃ 20 ℃ 30 ℃

Surface dry - - -

Touch dry 5 ｍｉｎｕｔｅ(ｓ) 3 ｍｉｎｕｔｅ(ｓ) 1 ｍｉｎｕｔｅ(ｓ)

*Drying time may vary depending on film thickness，ventilation，humidity，undercoat paint

condition etc.

Overcoating Interval 5℃ 20 ℃ 30 ℃
Minimum 24 ｈｏｕｒ(ｓ) 24 ｈｏｕｒ(ｓ) 24 ｈｏｕｒ(ｓ)
Maximum 6 ｍｏｎｔｈ(ｓ) 6 ｍｏｎｔｈ(ｓ) 6 ｍｏｎｔｈ(ｓ)

*The overcoating intervals are based on overcoating with same or same type of paint.

Tｙpical ｕndercoat -

Typical ｔopcoat ZINCTECT, EPOTECT, ESCO, etc

SAFETY PRECAUTIONS Detail information is given on Safety Data Sheet (SDS). Avoid inhalation of spray mist or vapour.
Avoid skin and eye contact. Paint contacted with skin should be immediately removed with water
and/or suitable cleanser. Eyes should be flushed with water and seek immediate medical attention.
Since this product contains flammable solvents, keep away from sparks and open flames.
Application and handling of this product should be in compliance with relevant national regulations.

STORAGE Store in dry, cool condition and away from sources of heat and ignition. Containers must be kept
tightly closed. Store conditions shall be in accordance with national regulations.

SHELF LIFE 6 months from date of production

GENERAL REMARKS - This product is moisture sensitive and store in cool and dry indoor area.
- Zinc powder in mixed paint tends to sink due to heavy specific gravity. Stir slowly during
application to prevent zinc powder settling.
- Contamination of other thinner may spoil paint film formation. Wash spray equipment
sufficiently with ZINCTECT 1000HA THINNER before using.
- Cracking may occur when total thickness is more than 50 microns by short interval (within 7
days) application.
- Thickness shall be controlled from 15 to 25 microns for ideal cutting welding work.
- Oil and alkyd paint is not suitable for overcoating.
- Wear protection mask and supply good ventilation when cutting and welding work.

*If any inquiries, please consult Kansai Paint representative for further information.

DISCLAIMER : The information given on this sheet is to the best of our knowledge and accurance
at the time of issuing.Since conditions of use are beyond the manufacturer's control，information
contained herein is without warranty，implied or otherwise，and the suitability of the material for
the use contemplated is the sole responsibility of the buyer.The information contained on this
data sheet is subject to modification at any time due to our policy of modification and product development.
Page 2of 2
ISSUED DATE : 27/03/2017