1. Water Closet/Bidet to Water Closet/Bidet c/c distance 23.

Vent termination above any air intake opening or similar

0.75 m matters.
2. Water Closet/Bidet to side partition. 0.9 m
.375 m 24. Restaurant kitchen sinks may be made of approved-type
3. Urinal to Urinal c/c distance bonderized and galvanized steel sheet of not less than ____.
0.6 m G.A. 16
4. Urinal to side partition 25. Continuous waste and fixture tailpiece with exposed
0.3 m connections may be seamless drawn brass not less than
5. Vent termination above the roof _____.
0.15 m g.a. 20
6. Vent termination from any vertical surface. 26. Minimum thickness of copper pans or liners.
0.3 m G.A. 24
7. Vent termination from any air intake opening or similar 27. Minimum thickness of condensers made of metal.
matters. G.A. 12
3m
8. Vent termination from any part of the roof that is used 28. Thickness of exposed drawn brass tubing trap that may
for other purposes. be used on fixtures discharging domestic sewage excluding
3.0 m urine.
9. Vent termination above any part of the roof that is used G.A. 17
for other purposes. 29. Minimum wall thickness of any steel septic tank.
2.1 m G.A. 12
10. Connection point of yoke vent to vent stack above the 30. Maximum percent of lead content for solders and fluxes
floor level that is used to convey potable water.
1m 0.2%
11. Fixture outlets connected to a horizontal drainage 31. Maximum percent of lead content for water pipes and
piping connected to a vertical drainage piping containing fittings that is used to convey potable water.
suds-producing fixtures. 8%
2.4 m 32. Considered as excessive water pressure.
12. Min. to max water trap seal. 551 kPa or 80 psi
2” – 4” 33. Considered as inadequate water pressure.
13. Min. to max shower receptor slope 103.15 psi
2% - 4% 34. Length of horizontal drain that does not require clean-
14. Depth of shower curb or threshold measured from the out unless such line is serving sinks or urinals.
shower drain. 1.5m
2” – 9” 35. Max distance of vent away from any lot line, alley and
15. Depth of shower curb or threshold measured from the street boundary lines.
outside floor. 0.9 m
1” or 25mm 36. Max length of tailpiece from any fixture
16. Shower threshold shall be of sufficient width to 0.6 m
accommodate a minimum wide door. 37. Min. to max length of air chamber
559 mm 12” – 18”
17. Shower receptors should encompassed a ___ mm 38. Min. fixture supply pipe for bidet
diameter circle. 13 mm
762 mm 39. Min. fixture supply pipe for flush tank water closet
18. Min. interior area of a shower receptor. 10mm
0.6 sq.m. 400. Min. fixture supply pipe for wash basin
19. Mounting height of wall hung lavatory from the floor 10mm
level line. 41. Min. fixture drain size for a water closet
0.8 m 76mm
20. Max mounting height of toilet grab bars from floor level 42. Min. fixture drain size for bath tub
line. 38mm
0.85 m 43. Min. diameter for an individual vent
21. Max mounting height of tissue paper holder from floor 32mm
level line. 44. Length of pipe to consider for permissible friction loss in
0.9 m water supply pipe sizing
22. Max spacing of drains for gang shower. 30.4m or 100ft
4.9 m 45. Sizing for downspouts is based on the pipes flowing ___
full
 7/24 70. Minimum clear horizontal distance between seepage pit
46. Ratio of side dimensions to consider when using to another seepage pit.
rectangular downspout. 3.7m
3:1
47. Minimum area of trench bottom of each arm system of
drain field.
14.2 sq.m.
48. Max length of digestive chamber to require a manhole
over the baffle wall.
3.7 m
49. Air space clearance required for septic tank.
9” or 228.6mm
50. Minimum size of inverted fitting for the septic tank inlet.
104.6mm
51. Minimum number of lines per drain field.
1
52. Required maximum slope of drain line
25mm/m
53. Min. center to center distance of drain field lines.
1.8m
54. Maximum distance clearance of perimeter for leaching
bed from a distribution drain line.
1.2m
55. Min. bottom width of trench for drain line.
457.2mm/18”
56. Max. bottom width of trench for drain line.
914.4mm/36”
57. Min. diameter of seepage pit.
2.2m
58. Minimum sidewall depth of seepage pit from the inlet.
3m
59. Minimum head of water required for testing of
plumbing in water test.
3m
60. Minimum liquid depth of septic tank
0.6 m
61. Maximum liquid depth of septic tank
1.8 m
62. Maximum distance between manhole
91m
63. Max distance of lot line to public sewer to be made
available.
61m
64. Abandoned house sewer should be capped or plugged
within ___ of the property line.
1.5m
65. How many days from the time of connecting the house
sewer to public line should the temporary disposal facilities
be filled with approved materials.
30 days
66. Thickness of colored striped bands for copper tubing.
6.4mm
67. Minimum number of bolts for closet flange connection.
4
68. Minimum vent size serving water closet.
51mm or 2”
69. Thickness of backfill per layer for trenches.
0.3m
1. Water Closet/Bidet to Water Closet/Bidet c/c distance 23. Vent termination above any air intake opening or similar
matters.
2. Water Closet/Bidet to side partition.
24. Restaurant kitchen sinks may be made of approved-type
3. Urinal to Urinal c/c distance bonderized and galvanized steel sheet of not less than ____.

4. Urinal to side partition 25. Continuous waste and fixture tailpiece with exposed
connections may be seamless drawn brass not less than
5. Vent termination above the roof _____.
150mm
6. Vent termination from any vertical surface. 26. Minimum thickness of copper pans or liners.

7. Vent termination from any air intake opening or similar 27. Minimum thickness of condensers made of metal.
matters.

8. Vent termination from any part of the roof that is used 28. Thickness of exposed drawn brass tubing trap that may
for other purposes. be used on fixtures discharging domestic sewage excluding
urine.
9. Vent termination above any part of the roof that is used
for other purposes. 29. Minimum wall thickness of any steel septic tank.

10. Connection point of yoke vent to vent stack above the 30. Maximum percent of lead content for solders and fluxes
floor level that is used to convey potable water.

11. Fixture outlets connected to a horizontal drainage 31. Maximum percent of lead content for water pipes and
piping connected to a vertical drainage piping containing fittings that is used to convey potable water.
suds-producing fixtures.
32. Considered as excessive water pressure.
12. Min. to max water trap seal.
33. Considered as inadequate water pressure.
13. Min. to max shower receptor slope
34. Length of horizontal drain that does not require clean-
14. Depth of shower curb or threshold measured from the out unless such line is serving sinks or urinals.
shower drain.
35. Max distance of vent away from any lot line, alley and
15. Depth of shower curb or threshold measured from the street boundary lines.
outside floor.
36. Max length of tailpiece from any fixture
16. Shower threshold shall be of sufficient width to
accommodate a minimum wide door. 37. Min. to max length of air chamber

17. Shower receptors should encompassed a ___ mm 38. Min. fixture supply pipe for bidet
diameter circle.
39. Min. fixture supply pipe for flush tank water closet
18. Min. interior area of a shower receptor.
400. Min. fixture supply pipe for wash basin
19. Mounting height of wall hung lavatory from the floor
level line. 41. Min. fixture drain size for a water closet

20. Max mounting height of toilet grab bars from floor level 42. Min. fixture drain size for bath tub
line.
43. Min. diameter for an individual vent
21. Max mounting height of tissue paper holder from floor
level line. 44. Length of pipe to consider for permissible friction loss in
water supply pipe sizing
22. Max spacing of drains for gang shower.
45. Sizing for downspouts is based on the pipes flowing ___
full
46. Ratio of side dimensions to consider when using 70. Minimum clear horizontal distance between seepage pit
rectangular downspout. to another seepage pit.

47. Minimum area of trench bottom of each arm system of

drain field.

48. Max length of digestive chamber to require a manhole

over the baffle wall.

49. Air space clearance required for septic tank.

50. Minimum size of inverted fitting for the septic tank inlet.

51. Minimum number of lines per drain field.

52. Required maximum slope of drain line

53. Min. center to center distance of drain field lines.

54. Maximum distance clearance of perimeter for leaching

bed from a distribution drain line.

55. Min. bottom width of trench for drain line.

56. Max. bottom width of trench for drain line.

57. Min. diameter of seepage pit.

58. Minimum sidewall depth of seepage pit from the inlet.

59. Minimum head of water required for testing of

plumbing in water test.

60. Minimum liquid depth of septic tank

61. Maximum liquid depth of septic tank

62. Maximum distance between manhole

63. Max distance of lot line to public sewer to be made

available.

64. Abandoned house sewer should be capped or plugged

within ___ of the property line.

65. How many days from the time of connecting the house
sewer to public line should the temporary disposal facilities
be filled with approved materials.

66. Thickness of colored striped bands for copper tubing.

67. Minimum number of bolts for closet flange connection.

68. Minimum vent size serving water closet.

69. Thickness of backfill per layer for trenches.