313 Ultra-slim Photoelectric Sensor Amplifier Built-in

EX-10 SERIES Ver.2

■■General terms and conditions.............. F-7 ■■Sensor selection guide................... P.271~
FIBER Related Information
SENSORS Glossary of terms / General precautions......P.1455~ / P.1458~ ■■Korea’s S-mark.............................. P.1506
LASER
SENSORS

PHOTOELECTRIC
SENSORS Conforming to Recognition
EMC Directive
MICRO (Excluding EX-15□/17□)
PHOTOELECTRIC
SENSORS
AREA
SENSORS Certified
(Some models only)
LIGHT CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS

SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS

MEASUREMENT
SENSORS panasonic.net/id/pidsx/global PNP output
type available
STATIC ELECTRICITY
PREVENTION
DEVICES
LASER
MARKERS

PLC
Amplifier built-in extraordinarily small and slim size
HUMAN MACHINE
INTERFACES Smallest body, just 3.5 mm 0.138 in thick Flexible mounting
ENERGY CONSUMPTION
VISUALIZATION
COMPONENTS
It can be mounted in a very The diffuse reflective type sensor is front sensing and is
small space as its size is just so thin that it gives an impression of being just pasted
FA COMPONENTS W10 × H14.5 × D3.5 mm on the mounting base. The thru-beam type is available
W0.394 × H0.571 × D0.138 in as front sensing type, as well as, side sensing type,
MACHINE VISION (thru-beam, front sensing type). allowing flexible mounting.
SYSTEMS
Thru-beam Diffuse reflective
UV CURING • Front sensing type • Side sensing type • Front sensing type
SYSTEMS

Selection
Guide
Amplifier
Built-in
Power Supply
Built-in
Amplifier- A wide variety of narrow-beam type! Light diffusion is approx. 1/2 of standard type. EX-□S□
separated
Less interference with no slit, Possible to sense a minute object Long sensing range of 1 m 3.281
CX-400
narrow-pitch can be set. less than ø0.5 mm ø0.039 in with ft with narrow beam
no slit.
CY-100 The pitch of installation is 1/2 of A long 1 m 3.281 ft sensing range is
conventional models, so that the The series is applicable to sense a possible with narrow beam.
EX-10
close-installation is possible. No cost minute object without any cost.
EX-20 is necessary to purchase or install
EX-30 a slit.
EX-40
CX-440 EX-11□ / EX-11E□

EQ-30 ø0.5mm
EQ-500 EX-11S□

MQ-W EX-11S□ / EX-11SE□

RX-LS200
RX EX-19S□

RT-610
 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
314

APPLICATIONS FIBER
SENSORS

Positioning of PCBs Detecting ICs Detecting PCB rack LASER

SENSORS

PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
EX-19S□ SENSORS
LIGHT CURTAINS /
SAFETY
Transparent stick COMPONENTS
PRESSURE /
FLOW
IC EX-15□ SENSORS
EX-14□ INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
Detecting wafer cassette Detecting thin ring Checking for absence of capacitor in tray USE SENSORS

SENSOR
EX-14□ OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS

MEASUREMENT
SENSORS
STATIC ELECTRICITY
EX-13E□ PREVENTION
DEVICES
Guide
EX-14□ LASER
MARKERS

PLC
BASIC PERFORMANCE
HUMAN MACHINE
Electric power saving * High-speed response time: 0.5 ms INTERFACES
ENERGY CONSUMPTION
The EX-10 series The sensor is suitable for detecting small and high- VISUALIZATION
COMPONENTS
achieves reductions speed traveling objects.
in power consumption A maximum 35 % reduction
FA COMPONENTS
of up to 65 %. These compared to conventional
sensors MACHINE VISION
sensors contribute SYSTEMS
to environmental
friendliness. UV CURING
SYSTEMS
* Effective from production
in October 2010.

Selection
Guide
Minimum sensing object: ø1 mm ø0.039 in EX-11(E)□, EX-15(E)□ Long sensing range: 1 m 3.281 ft EX-19(E)□ Amplifier
Built-in
Power Supply
EX-11□, EX-11E□, EX-15 and A sensing range of 1 m Built-in
EX-15E are incorporated 3.281 ft has been realized Amplifier-
separated
with ø1 mm ø0.039 in with a slim size of just 3.5 1m
slit masks so that ø1 mm mm 0.138 in. It can be used 3.281 ft
ø0.039 in, or more, object to detect even wide IC trays. CX-400
can be detected. Hence, CY-100
they are suitable for precise
EX-10
positioning or small parts
detection. EX-20

Background suppression EX-14□ EX-30

EX-40
Hardly affected by background Black object reliably detected CX-440
The best distance
Even a specular background It can reliably detect dark is approx. 10 mm EQ-30
separated by 100 mm 3.937 Background
color objects since it is 0.394 in from the
object. EQ-500
in, or more, is not detected. 100 mm convergent reflective type.
3.937 in
(However, the background MQ-W
should be directly opposite. RX-LS200
A spherical or curved
RX
background may be
detected.) RT-610
315 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2

FIBER ENVIRONMENTAL RESISTANCE

SENSORS

LASER Incorporated an inverter countermeasure circuit * Waterproof IP67

SENSORS
The EX-10 series become Fluorescent light The sensor can be hosed down because of its IP67
PHOTOELECTRIC
SENSORS significantly stronger construction and the non-corrosive stainless steel
MICRO against inverter light and mounting bracket.
PHOTOELECTRIC
SENSORS
other extraneous light.
Note: However, take care that if it is exposed to water splashes during
* Effective from production in
AREA operation, it may detect a water drop itself.
SENSORS October 2010.
LIGHT CURTAINS /
SAFETY
COMPONENTS Bending durability EX-□-R
PRESSURE /
FLOW
SENSORS Flexible cable type EX-□-R is available. It is most
INDUCTIVE suitable for moving parts, such as robot arm, etc.
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
MOUNTING / SIZE
SENSOR Mountable with M3 screws
OPTIONS
SIMPLE Non-corrosive stainless steel type sensor mounting bracket is also available.
WIRE-SAVING
UNITS • MS-EX10-1 • MS-EX10-2 • MS-EX10-3
WIRE-SAVING [Cold rolled carbon steel (SPCC)] [Cold rolled carbon steel (SPCC)] [Cold rolled carbon steel (SPCC)]
SYSTEMS
MS-EX10-11 MS-EX10-12 MS-EX10-13
MEASUREMENT [Stainless steel (SUS304)] [Stainless steel (SUS304)] [Stainless steel (SUS304)]
SENSORS mounting bracket for the front mounting bracket for the side (L-shaped mounting bracket)
STATIC ELECTRICITY sensing type sensing type
PREVENTION
DEVICES M3 screws
LASER
MARKERS

PLC

M3 screws
HUMAN MACHINE
INTERFACES
M3 screws
ENERGY CONSUMPTION
VISUALIZATION Note: Sensor mounting brackets can not be used for
COMPONENTS
the narrow beam type (EX-□S□).
FA COMPONENTS
Red beam makes beam alignment easy
MACHINE VISION
SYSTEMS
The red LED beam projected from the emitter helps you
UV CURING to align the sensor heads.
SYSTEMS

FUNCTIONS VARIETIES
Bright 2-color indicator Operation mode switch EX-15□/17□
A convenient 2-color Thru-beam type sensor incorporated with an operation
Selection
Guide indicator has been mode switch on the bifurcation is also available. It helps
Amplifier incorporated in the you to test the operability before start-up.
Built-in
Power Supply miniature body.
Built-in
Amplifier-
separated
2-color indicator
Orange: Operation indicator
CX-400 Green: Stability indicator
Operation mode switch
CY-100
Even for the thru-beam
EX-10 Operation indicator SENS.
type sensor, only three
(Orange)
EX
-17
wires have to be connected.
EX-20
EX-30 OTHERS
EX-40 Less resources used *
CX-440
Based on environmental
EQ-30
considerations, simplified
EQ-500 packaging is used in order
MQ-W to reduce waste.
In addition, the bag is
RX-LS200
made from polyethylene
RX which produces no toxic
RT-610 gases even when burned.
* Effective from production in
October 2010.
 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
316

ORDER GUIDE FIBER

SENSORS

LASER
SENSORS
Model No.(Note 2) Output
Type Appearance Sensing range operation Output PHOTO-
NPN output PNP output ELECTRIC
SENSORS
EX-11A EX-11A-PN Light-ON MICRO
150 mm 5.906 in PHOTO-
ELECTRIC
EX-11B EX-11B-PN Dark-ON SENSORS

500 mm EX-13A EX-13A-PN Light-ON AREA

SENSORS
19.685 in
EX-13B EX-13B-PN Dark-ON
Front sensing

LIGHT
CURTAINS /
SAFETY
1m EX-19A EX-19A-PN Light-ON COMPONENTS
3.281 ft PRESSURE /
EX-19B EX-19B-PN Dark-ON FLOW
SENSORS
switch on the bifurcation

150 mm 5.906 in EX-15 EX-15 -PN INDUCTIVE

With operation mode

Switchable PROXIMITY
either SENSORS
Light-ON or PARTICULAR
500 mm USE
EX-17 EX-17-PN Dark-ON
Thru-beam

19.685 in SENSORS

NPN open- SENSOR

EX-11EA EX-11EA-PN
Standard Type

Light-ON collector OPTIONS

150 mm 5.906 in
transistor
EX-11EB EX-11EB-PN Dark-ON
or
SIMPLE
WIRE-SAVING
UNITS
EX-13EA EX-13EA-PN Light-ON PNP open-
500 mm
collector
19.685 in WIRE-SAVING
EX-13EB EX-13EB-PN Dark-ON transistor SYSTEMS
Side sensing

1m EX-19EA EX-19EA-PN Light-ON MEASURE-

MENT
3.281 ft SENSORS
EX-19EB EX-19EB-PN Dark-ON
STATIC
ELECTRICITY
switch on the bifurcation

PREVENTION
150 mm 5.906 in EX-15E - DEVICES
With operation mode

Switchable
either LASER
Light-ON or MARKERS
500 mm
19.685 in EX-17E - Dark-ON
PLC
Convergent reflective
(Diffused beam type)

Front sensing

HUMAN
EX-14A EX-14A-PN Light-ON MACHINE
INTERFACES
2 to 25 mm 0.079 to 0.984 in (Note 1)
ENERGY
(Convergent point: 10 mm 0.394 in) CONSUMPTION
EX-14B EX-14B-PN Dark-ON VISUALIZATION
COMPONENTS

FA
EX-11SA EX-11SA-PN Light-ON COMPONENTS
150 mm 5.906 in
EX-11SB EX-11SB-PN Dark-ON MACHINE
Front sensing

VISION
SYSTEMS
500 mm EX-13SA EX-13SA-PN Light-ON
19.685 in UV
Narrow beam type

EX-13SB EX-13SB-PN Dark-ON NPN open- CURING

collector SYSTEMS
Thru-beam

1m EX-19SA EX-19SA-PN Light-ON transistor

3.281 ft or
EX-19SB EX-19SB-PN Dark-ON PNP open-
collector
EX-11SEA EX-11SEA-PN Light-ON transistor
Side sensing

150 mm 5.906 in
EX-11SEB EX-11SEB-PN Dark-ON
Selection
Guide
500 mm EX-13SEA EX-13SEA-PN Light-ON
Amplifier
19.685 in Built-in
EX-13SEB EX-13SEB-PN Dark-ON Power Supply
Built-in
Amplifier-
NOTE: Mounting bracket is not supplied with the sensor. Please select from the range of optional sensor mounting brackets separated
(MS-EX10-□). Sensor mounting brackets (MS-EX10-□) can not be used for the narrow beam type (EX-□S□).
Notes: 1) The sensor does not detect even a specular background if it is separated by 100 mm 3.937 in or more. (However, the background should be directly CX-400
opposite. A spherical or curved background may be detected.)
2) The model No. with “P” shown on the label affixed to the thru-beam type sensor is the emitter, “D” shown on the label is the receiver. CY-100

EX-10
Flexible cable type
EX-20
Flexible cable type is also available for NPN output type. (excluding narrow beam type EX-□S□ and sensor with operation mode switch on the bifurcation
EX-30
EX-15□/17□)
When ordering this type, suffix “-R” to the model No. EX-40
(e.g.) Flexible cable type of EX-11A is “EX-11A-R”.
CX-440

5 m 16.404 ft cable length type EQ-30

EQ-500
5 m 16.404 ft cable length type (standard: 2 m 6.562 ft) is also available for NPN output type. (excluding narrow beam type EX-□S□ and flexible cable type)
When ordering this type, suffix “-C5” to the model No. MQ-W
(e.g.) 5 m 16.404 ft cable length type of EX-11A is “EX-11A-C5”.
RX-LS200

RX

RT-610
 317 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2

FIBER
SENSORS
OPTIONS
LASER
SENSORS
NOTE: Sensor mounting brackets can not be used for the narrow beam type (EX-□S□). Sensor mounting bracket
PHOTO-
ELECTRIC
• MS-EX10-1 • MS-EX10-11
SENSORS
MICRO
PHOTO- Designation Model No. Description
ELECTRIC
SENSORS

AREA Mounting bracket for the front sensing type sensor [Cold rolled carbon steel (SPCC)]
SENSORS MS-EX10-1 (The thru-beam type sensor needs two brackets.)
LIGHT
CURTAINS / Mounting bracket for the side sensing type sensor [Cold rolled carbon steel (SPCC)]
SAFETY MS-EX10-2 (The thru-beam type sensor needs two brackets.)
COMPONENTS
PRESSURE /
FLOW L-shaped mounting bracket sensor [Cold rolled carbon steel (SPCC)]
SENSORS Sensor mounting MS-EX10-3 (The thru-beam type sensor needs two brackets.) Material: Cold rolled Material: Stainless
INDUCTIVE bracket carbon steel (SPCC) steel (SUS304)
PROXIMITY (Note 1) Mounting bracket for the front sensing type sensor [Stainless steel (SUS304)] (Uni-chrome plated) Two M2 (length 4 mm
SENSORS MS-EX10-11 (The thru-beam type sensor needs two brackets.) Two M2 (length 4 mm 0.157 in) pan head
PARTICULAR 0.157 in) pan head screws [stainless
USE Mounting bracket for the side sensing type sensor [Stainless steel (SUS304)] screws are attached. steel (SUS304)] are
SENSORS MS-EX10-12 (The thru-beam type sensor needs two brackets.) attached.
SENSOR
OPTIONS L-shaped mounting bracket [Stainless steel (SUS304)]
MS-EX10-13 (The thru-beam type sensor needs two brackets.)
SIMPLE • MS-EX10-2 • MS-EX10-12
WIRE-SAVING
UNITS • Sensing range: 600 mm 23.622 in [EX-19□]
Slit on one side 250 mm 9.843 in [EX-13□, EX-17□]
WIRE-SAVING
SYSTEMS • Min. sensing object: ø2 mm ø0.079 in
OS-EX10-12
(Slit size ø1.2 mm ø0.047 in)
MEASURE- • Sensing range: 400 mm 15.748 in [EX-19□]
MENT
SENSORS Slit on both sides 200 mm 7.874 in [EX-13□, EX-17□]
STATIC • Min. sensing object: ø1.2 mm ø0.047 in
ELECTRICITY
PREVENTION
DEVICES • Sensing range: 800 mm 31.496 in [EX-19□]
Slit on one side 350 mm 13.780 in [EX-13□]
LASER Slit mask Material: Cold rolled Material: Stainless
MARKERS • Min. sensing object: ø2 mm ø0.079 in
OS-EX10-15 carbon steel (SPCC) steel (SUS304)
(Slit size ø1.5 mm ø0.059 in) (Uni-chrome plated) Two M2 (length 8 mm
• Sensing range: 500 mm 19.685 in [EX-19□]
PLC Two M2 (length 8 mm 0.315 in) pan head
Slit on both sides 300 mm 11.811 in [EX-13□]
0.315 in) pan head screws [stainless
• Min. sensing object: ø1.5 mm ø0.059 in screws are attached. steel (SUS304)] are
HUMAN
MACHINE attached.
INTERFACES • Sensing range: 250 mm 9.843 in [EX-13E□, EX-17E□]
Slit on one side
ENERGY • Min. sensing object: ø2 mm ø0.079 in
CONSUMPTION OS-EX10E-12
VISUALIZATION (Slit size ø1.2 mm ø0.047 in)
COMPONENTS • Sensing range: 200 mm 7.874 in [EX-13E□, EX-17E□] • MS-EX10-3 • MS-EX10-13
Slit on both sides
FA
• Min. sensing object: ø1.2 mm ø0.047 in
COMPONENTS
Sensor checker It is useful for beam alignment of thru-beam type sensors. The optimum
MACHINE (Note 2)
CHX-SC2 receiver position is given by indicators, as well as an audio signal.
VISION
SYSTEMS
Mounting screws with washers (50 pcs. lot). It can mount
UV Mounting screw MS-M2 securely as it is spring washer attached.
CURING
SYSTEMS
Notes: 1) Can not be used for the narrow beam type (EX-□S□).
2) Refer to p.980 for details of the sensor checker CHX-SC2.

Slit mask Sensor checker Material: Cold rolled Material: Stainless steel
carbon steel (SPCC) (SUS304)
• OS-EX10-12 • OS-EX10E-12 Example of mounting • CHX-SC2 (Uni-chrome plated) Two M2 (length 4 mm
• OS-EX10-15 (OS-EX10E-12) Two M2 (length 4 mm 0.157 in) pan head
Selection
Guide 0.157 in) pan head screws [stainless
Amplifier
PO
W
ER C
H
X-
screws, and two M2 steel (SUS304)] and
Built-in LE
VE
L
SC
2 (length 8 mm 0.315 in) two M2 (length 8 mm
Power Supply pan head screws are 0.315 in) pan head
Built-in attached. screws [stainless steel
Amplifier- (SUS304)] are attached.
separated
Sensor checker

CX-400
Tighten along with the sensor
CY-100 mounting bracket.
EX-10

EX-20

EX-30

EX-40

CX-440

EQ-30

EQ-500

MQ-W

RX-LS200

RX

RT-610
 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
318

SPECIFICATIONS FIBER
SENSORS

LASER
SENSORS
Thru-beam • standard type PHOTO-
Type ELECTRIC
SENSORS
Front sensing Side sensing Front sensing Side sensing Front sensing Side sensing MICRO
PHOTO-
Model No. Light-ON EX-11A(-PN) EX-11EA(-PN) EX-13A(-PN) EX-13EA(-PN) EX-19A(-PN) EX-19EA(-PN) ELECTRIC
SENSORS
(Note 2) Dark-ON EX-11B(-PN) EX-11EB(-PN) EX-13B(-PN) EX-13EB(-PN) EX-19B(-PN) EX-19EB(-PN)
Item AREA
SENSORS
Sensing range 150 mm 5.906 in 500 mm 19.685 in 1 m 3.281 ft LIGHT
CURTAINS /
ø1 mm ø0.039 in opaque object ø2 mm ø0.079 in opaque object ø2 mm ø0.079 in SAFETY
opaque object COMPONENTS
(Completely beam interrupted object) (Completely beam interrupted object)
PRESSURE /
Setting distance Setting distance Completely beam FLOW
Min. sensing object between emitter between emitter interrupted object SENSORS

and receiver: and receiver: Setting distance between INDUCTIVE

emitter and receiver: PROXIMITY
150 mm 5.906 in 500 mm 19.685 in SENSORS
1 m 3.281 ft
PARTICULAR
Hysteresis – USE
SENSORS

Repeatability (perpendicular to sensing axis) 0.05 mm 0.002 in or less SENSOR

OPTIONS
Supply voltage 12 to 24 V DC ±10 %   Ripple P-P 10 % or less
SIMPLE
Current consumption Emitter: 10 mA or less, Receiver: 10 mA or less WIRE-SAVING
UNITS

<NPN output type> <PNP output type> WIRE-SAVING

NPN open-collector transistor PNP open-collector transistor SYSTEMS
• Maximum sink current: 50 mA • Maximum source current: 50 mA
Output MEASURE-
• Applied voltage: 30 V DC or less (between output and 0 V) • Applied voltage: 30 V DC or less (between output and +V) MENT
• Residual voltage: 2 V or less (at 50 mA sink current) • Residual voltage:2 V or less (at 50 mA source current) SENSORS
1 V or less (at 16 mA sink current) 1 V or less (at 16 mA source current) STATIC
ELECTRICITY
PREVENTION
Utilization category DC-12 or DC-13 DEVICES

LASER
Short-circuit protection Incorporated MARKERS

Response time 0.5 ms or less

PLC
Operation indicator Orange LED (lights up when the output is ON)
HUMAN
Incident beam indicator – MACHINE
INTERFACES

Green LED ENERGY

Stability indicator CONSUMPTION
(lights up under stable light received condition or stable dark condition) VISUALIZATION
COMPONENTS
Pollution degree 3 (Industrial environment) FA
COMPONENTS
Protection IP67 (IEC)
MACHINE
VISION
Ambient temperature −25 to +55 °C −13 to +131 °F (No dew condensation or icing allowed), Storage: −30 to +70 °C −22 to +158 °F
Environmental resistance

SYSTEMS

Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH UV

CURING
SYSTEMS
Ambient illuminance Incandescent light: 3,000 ℓx at the light-receiving face

EMC EN 60947-5-2

Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure

Insulation resistance 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure

Vibration resistance 10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each Selection
Guide
Amplifier
Shock resistance 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each Built-in
Power Supply
Emitting element Red LED (Peak emission wavelength: 680 nm 0.027 mil (EX-19E□: 624 nm 0.025 mil), modulated) Built-in
Amplifier-
Enclosure: Polyethylene terephthalate separated
Material
Lens: Polyalylate

0.1 mm2 3-core (thru-beam type emitter: 2-core) cabtyre cable, CX-400
Cable (Note 5)
2 m 6.562 ft long
CY-100
Cable extension Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (thru-beam type: emitter and receiver).
EX-10
Weight Net weight (each emitter and receiver): 20 g approx., Gross weight: 50 g approx.
EX-20
Accessories Mounting screws: 1 set
EX-30
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.
2) Model Nos. having the suffix “-PN” are PNP output type. EX-40
3) The flexible cable type (model Nos. having suffix “-R”) has a 0.1 mm2 3-core (thru-beam type emitter: 2-core) flexible cabtyre cable, 2 m 6.562 ft long. CX-440

EQ-30

EQ-500

MQ-W

RX-LS200

RX

RT-610
 319 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2

FIBER
SENSORS
SPECIFICATIONS
LASER
SENSORS
Convergent reflective
Thru-beam • narrow beam type Thru-beam · with operation mode switch on bifurcation
PHOTO-
Type (Diffused beam type)
ELECTRIC
SENSORS
MICRO
Front sensing Side sensing Front sensing Side sensing Front sensing Front sensing Front sensing Side sensing Front sensing Side sensing
PHOTO-
ELECTRIC
SENSORS Model No. Light-ON EX-11SA(-PN) EX-11SEA(-PN) EX-13SA(-PN) EX-13SEA(-PN) EX-19SA(-PN) EX-14A(-PN) EX-15 EX-15E EX-17 EX-17E
(Note 2) Dark-ON EX-11SB(-PN) EX-11SEB(-PN) EX-13SB(-PN) EX-13SEB(-PN) EX-19SB(-PN) EX-14B(-PN) (Note 3) (Note 3) (Note 3) (Note 3)
AREA
SENSORS
Item
LIGHT
2 to 25 mm 0.079
CURTAINS / Sensing range 150 mm 5.906 in 500 mm 19.685 in 1 m 3.281 ft to 0.984 in (Note 4) 150 mm 5.906 in 500 mm 19.685 in
SAFETY
COMPONENTS (Conv. point: 10 mm 0.394 in)
PRESSURE /
FLOW ø0.5 mm ø1 mm ø0.039 in opaque object ø2 mm ø0.079 in opaque object
SENSORS ø0.002 in
ø1 mm ø0.039 in opaque object ø2 mm ø0.079 in opaque object ø0.1 mm ø0.004 (Completely beam interrupted object) (Completely beam interrupted object)
opaque object Setting distance Setting distance
INDUCTIVE
PROXIMITY (Completely beam interrupted object) (Completely beam interrupted object) in copper wire
Min. sensing object (Completely between emitter between emitter
SENSORS (Note 5) (Note 5) Setting distance:
beam interrupted and receiver: and receiver:
PARTICULAR object) 10 mm 0.394 in
USE 150 mm 5.906 in 500 mm 19.685 in
SENSORS (Note 5)

SENSOR
– 15 % or less of operation –
OPTIONS Hysteresis
distance (Note 4)
SIMPLE
WIRE-SAVING Repeatability (perpendicular to sensing axis) 0.05 mm 0.002 in or less 0.1 mm 0.004 in or less 0.05 mm 0.002 in or less
UNITS
Supply voltage 12 to 24 V DC ±10 %   Ripple P-P 10 % or less
WIRE-SAVING
SYSTEMS
Current consumption Emitter: 10 mA or less, Receiver: 10 mA or less 13 mA or less 25 mA or less
MEASURE-
MENT <NPN output type> <PNP output type> NPN open-collector transistor
SENSORS NPN open-collector transistor PNP open-collector transistor • Maximum sink current: 100 mA
STATIC • M aximum sink current: 50 mA • M aximum source current: 50 mA • Applied voltage: 30 V DC or less (between output and 0 V)
ELECTRICITY Output
PREVENTION • A pplied voltage: 30 V DC or less (between output and 0 V) • A pplied voltage: 30 V DC or less (between output and +V) • R esidual voltage: 2 V or less
DEVICES • R esidual voltage: 2 V or less (at 50 mA sink current) • R esidual voltage: 2 V or less (at 50 mA source current) (at 100 mA sink current)
LASER 1 V or less (at 16 mA sink current) 1 V or less (at 16 mA source current) 1 V or less (at 16 mA sink current)
MARKERS
Utilization category DC-12 or DC-13 –
PLC
Short-circuit protection Incorporated
HUMAN
MACHINE Response time 0.5 ms or less
INTERFACES
ENERGY Operation indicator Orange LED (lights up when the output is ON) Orange LED (lights up when the output is ON), located on the bifurcation
CONSUMPTION
VISUALIZATION
COMPONENTS – Red LED (lights up under light received condition),
Incident beam indicator
located on the receiver
FA
COMPONENTS
Green LED (lights up under stable light received
Green LED
MACHINE Stability indicator condition or stable dark condition), located on the
VISION (lights up under stable light received condition or stable dark condition)
SYSTEMS receiver
UV Pollution degree 3 (Industrial environment) –
CURING
SYSTEMS
Protection IP67 (IEC)

Ambient temperature −25 to +55 °C −13 to +131 °F (No dew condensation or icing allowed), Storage: −30 to +70 °C −22 to +158 °F
Environmental resistance

Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH

Ambient illuminance Incandescent light: 3,000 ℓx at the light-receiving face

Selection –
Guide EMC EN 60947-5-2
Amplifier
Built-in Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure
Power Supply
Built-in Insulation resistance 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
Amplifier-
separated Vibration resistance 10 to 500 Hz frequency, 3 mm 0.118 in amplitude in X, Y and Z directions for two hours each

Shock resistance 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions for three times each
CX-400
Emitting element Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated) Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
CY-100
Enclosure: Polyethylene terephthalate Enclosure: Polyethylene terephthalate
Material
EX-10 Lens: Polyalylate Lens: Polyalylate, Bifurcation: Polyalylate
EX-20 0.1 mm2 3-core (thru-beam type emitter: 2-core) cabtyre cable, 0.2 mm2 3-core cabtyre cable, 2 m 6.562 ft long (beyond bifurcation;
Cable (Note 6)
2 m 6.562 ft long from emitter / receiver to bifurcation: 0.5 m 1.640 ft long)
EX-30

EX-40 Cable extension Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (thru-beam type: emitter and receiver). Extension up to total 100 m 328 ft is possible with 0.3 mm2, or more, cable.

CX-440 Net weight (each emitter and receiver): 20 g approx., Net weight: 20 g approx.
Weight Net weight: 55 g approx., Gross weight: 80 g approx.
Gross weight: 50 g approx. Gross weight: 40 g approx.
EQ-30
Accessories Mounting screws: 1 set Mounting screws: 1 set Mounting screws: 1 set, Adjusting screwdriver: 1 pc.
EQ-500
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.
MQ-W 2) Model Nos. having the suffix “-PN” are PNP output type.
RX-LS200 3) Either Light-ON or Dark-ON can be selected by the operation mode switch.
4) The sensing range and the hysteresis of convergent reflective type sensor are specified for white non-glossy paper (50 × 50 mm 1.969 × 1.969 in) as the object.
RX 5) The min. sensing objects are specified in case the emitter / reciever sensing range is to set the maximum.
6) The flexible cable type (model Nos. having suffix “-R”) has a 0.1 mm2 3-core (thru-beam type emitter: 2-core) flexible cabtyre cable, 2 m 6.562 ft long.
RT-610
 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
320

I/O CIRCUIT AND WIRING DIAGRAMS FIBER

SENSORS

LASER
EX-11□  EX-11S□  EX-13□  EX-13S□  EX-19□  EX-19S□  EX-14□ NPN output type SENSORS

I/O circuit diagram Wiring diagram PHOTO-

ELECTRIC
SENSORS
Color code MICRO
PHOTO-
ELECTRIC
D1 (Brown) +V SENSORS

AREA
Sensor circuit

(Black) Load Brown SENSORS

D2 Output (Note) + 12 to 24 V DC LIGHT
− ±10 % CURTAINS /
Load
Tr 50 mA max. Black (Note) + SAFETY
ZD 12 to 24 V DC COMPONENTS
(Blue) 0 V − ±10 %
PRESSURE /
FLOW
Blue SENSORS

Internal circuit Users’ circuit INDUCTIVE

Note: The emitter of the thru-beam type sensor does not incorporate the PROXIMITY
Note: The emitter of the thru-beam type sensor does not incorporate the SENSORS
black wire.
output. PARTICULAR
USE
SENSORS
Symbols … D1: Reverse supply polarity protection diode
D2: Reverse output polarity protection diode SENSOR
OPTIONS
ZD: Surge absorption zener diode
Tr : NPN output transistor SIMPLE
WIRE-SAVING
UNITS

EX-11□-PN  EX-11S□-PN  EX-13□-PN  EX-13S□-PN  EX-19□-PN  EX-19S□-PN  EX-14□-PN PNP output type WIRE-SAVING

SYSTEMS

I/O circuit diagram Wiring diagram MEASURE-

MENT
SENSORS
Color code
STATIC
ELECTRICITY
(Brown) +V PREVENTION
DEVICES
Sensor circuit

ZD LASER
50 mA max. Brown MARKERS
+ 12 to 24 V DC
Tr ±10 %
D2 (Black) Output (Note) −
Load Black (Note) + 12 to 24 V DC PLC
D1 (Blue) 0 V − ±10 %
Load HUMAN
Blue MACHINE
INTERFACES
Internal circuit Users’ circuit
ENERGY
Note: The emitter of the thru-beam type sensor does not incorporate the Note: The emitter of the thru-beam type sensor does not incorporate the CONSUMPTION
VISUALIZATION
output. black wire. COMPONENTS

FA
COMPONENTS
Symbols … D1: Reverse supply polarity protection diode
D2: Reverse output polarity protection diode MACHINE
ZD: Surge absorption zener diode VISION
SYSTEMS
Tr : PNP output transistor
UV
CURING
SYSTEMS
EX-15□  EX-15E□  EX-17□  EX-17E□ NPN output type

I/O circuit diagram EX-15□, EX-15E□, EX-17□, EX-17E□ wiring diagram

Color code

D1 (Brown) +V
Selection
Guide
Sensor circuit

Load Amplifier
D2 (Black) Output + 12 to 24 V DC Built-in

− ±10 % Power Supply

Tr 100 mA max. Built-in
ZD Amplifier-
(Blue) 0 V separated

Internal circuit Users’ circuit CX-400

CY-100
Symbols … D1: Reverse supply polarity protection diode
EX-10
D2: Reverse output polarity protection diode
ZD: Surge absorption zener diode EX-20
Tr : NPN output transistor
EX-30

EX-40
Brown
CX-440
Load
Black + 12 to 24 V DC EQ-30
− ±10 %
EQ-500
Blue
MQ-W

RX-LS200

RX

RT-610
 321 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2

FIBER
SENSORS
SENSING CHARACTERISTICS (TYPICAL)
LASER
SENSORS EX-11□  EX-11E□  EX-15□  EX-15E□ Thru-beam type *Optical properties of side sensing types (EX-□E□)
Due to the optical properties of side sensing types, note that sensing may
PHOTO- be affected if multiple sensors are positioned in such a way that optical
ELECTRIC Parallel deviation Angular deviation
SENSORS axes intersect as shown in the diagram below.
MICRO 200 200
PHOTO- 7.874 7.874
ELECTRIC
SENSORS
EX-11□ Emitter 2 Receiver 1 Beam from Emitter 1
Setting distance L (mm in)
Setting distance L (mm in)

AREA 150 EX-15□ 150

SENSORS 5.906 5.906 EX-11□ may be caught by Receiver 2.
EX-11E□ EX-15□
LIGHT EX-11□ EX-15E□
CURTAINS / 100 100 EX-11E□ Emitter 1 Receiver 2
SAFETY EX-15□ EX-11E□ EX-15E□
3.937 3.937
COMPONENTS
Emitter EX-15E□ Emitter
PRESSURE / Emitter Emitter
FLOW 50 50
SENSORS
1.969
ℓ L ℓ L θ
L
θ
L
Emitter 1 Receiver 1 There is no problem when
1.969
INDUCTIVE EX-11□ EX-11E□ sensors are installed in
Receiver ℓ × 2 or more
PROXIMITY Receiver EX-15□ Receiver Receiver EX-15E□ parallel
SENSORS 0 0
100 50 0 50 100 20 10 0 10 20 Emitter 2 Receiver 2 (although the distance
PARTICULAR 3.937 1.969 1.969 3.937 Left Center Right L between sensors should be
USE Left Center Right
SENSORS Operating angle θ ( ° ) ℓ × 2 or more).
Operating point ℓ (mm in)
SENSOR
OPTIONS

SIMPLE
EX-13□  EX-13E□  EX-17□  EX-17E□ Thru-beam type
WIRE-SAVING
UNITS
Parallel deviation Angular deviation Parallel deviation with slit Parallel deviation with slit
WIRE-SAVING masks (ø1.2 mm ø0.047 in) masks (ø1.5 mm ø0.059 in)
SYSTEMS
800 800 400 400
MEASURE- 31.496 31.496 15.748 EX-13□/17□ 15.748 Slit on one side
MENT Slit on one side or both sides
SENSORS
EX-13□/17□

Setting distance L (mm in)

Setting distance L (mm in)
Setting distance L (mm in)
Setting distance L (mm in)

STATIC 600 EX-13□ 600 300 Slit on both sides 300

ELECTRICITY 23.622 EX-17□ 23.622 11.811 11.811
PREVENTION EX-13E□/17E□
EX-13□ Slit on one side
DEVICES EX-13E□ EX-17□
LASER 400 EX-17E□ 400 200 EX-13E□/17E□ 200
EX-13E□ Slit on
MARKERS 15.748 Emitter 15.748 7.874 7.874 Slit on one side,
EX-17E□ both sides Emitter Emitter
Emitter Emitter sensing range: 350 mm 13.78 in
Emitter Slit on both sides,
PLC 200 ℓ L 200 100 100 sensing range: 300 mm 11.81 in
ℓ θ θ ℓ L ℓ L
7.874 L 7.874 L L 3.937 3.937
EX-13□ EX-13E□ EX-13□ EX-13E□
HUMAN Receiver Receiver
MACHINE Receiver EX-17□ EX-17E□ Receiver EX-17□ Receiver Receiver EX-17E□
INTERFACES 0 0 0 0
100 50 0 50 100 20 10 0 10 20 40 20 0 20 40 100 50 0 50 100
ENERGY 3.937 1.969 1.969 3.937 Left Center Right 1.575 0.787 0.787 1.575 3.937 1.969 1.969 3.937
CONSUMPTION Left Center Right Left Center Right
VISUALIZATION Left Center Right Operating angle θ ( ° )
COMPONENTS Operating point ℓ (mm in) Operating point ℓ (mm in) Operating point ℓ (mm in)

FA
COMPONENTS
EX-19□ Thru-beam type
MACHINE
VISION
SYSTEMS Parallel deviation Angular deviation Parallel deviation with slit Parallel deviation with slit
UV
CURING
masks (ø1.2 mm ø0.047 in) masks (ø1.5 mm ø0.059 in)
SYSTEMS
800
31.496
Slit on one side Slit on one side
1,000 1,000 1,000
Setting distance L (mm in)
Setting distance L (mm in)

Setting distance L (mm in)

Setting distance L (mm in)

39.370 39.370 600 39.370

23.622

Slit on both sides

400
Selection 15.748
Guide 500 Emitter 500 Emitter 500 Emitter
Emitter
Amplifier 19.685 19.685 19.685
θ
Built-in ℓ L 200 ℓ L
L ℓ L
Power Supply 7.874 Slit on both sides
Built-in Receiver
Receiver Receiver
Amplifier- Receiver
separated 0 0 0 0
200 100 0 100 200 40 20 0 20 40 200 100 0 100 200 200 100 0 100 200
7.874 3.937 3.937 7.874 Left Center Right 7.874 3.937 3.937 7.874 7.874 3.937 3.937 7.874
Left Center Right Operating angle θ ( ° ) Left Center Right Left Center Right
CX-400 Operating point ℓ (mm in) Operating point ℓ (mm in) Operating point ℓ (mm in)

CY-100
EX-19E□ Thru-beam type EX-11S□/EX-11SE□ Thru-beam type EX-13S□/EX-13SE□ Thru-beam type EX-19S□ Thru-beam type
EX-10

EX-20 Parallel deviation Parallel deviation Parallel deviation Parallel deviation

200 800
EX-30 7.874 31.496

EX-40 1,000 1,000

Setting distance L (mm in)

Setting distance L (mm in)

Setting distance L (mm in)

Setting distance L (mm in)

39.370 150 600 39.370

CX-440 5.906 EX-11S□ EX-11SE□ 23.622 EX-13S□ EX-13SE□

EQ-30
100 400 EX-13SE□
3.937 EX-11S□ EX-11SE□ 15.784 EX-13S□
EQ-500 500 Emitter Emitter 500
19.685 Emitter Emitter 19.685 Emitter
Emitter
MQ-W 50 200
ℓ L ℓ L ℓ ℓ
1.969 L 7.874 ℓ L L ℓ L
RX-LS200
Receiver Receiver Receiver
0 Receiver Receiver Receiver
RX 0 0 0
200 100 0 100 200 100 50 0 50 100 100 50 0 50 100 200 100 0 100 200
7.874 3.937 3.937 7.874 3.937 1.969 1.969 3.937 3.937 1.969 1.969 3.937 7.874 3.937 3.937 7.874
RT-610 Left Center Right Left Center Right Left Center Right Left Center Right
Operating point ℓ (mm in) Operating point ℓ (mm in) Operating point ℓ (mm in) Operating point ℓ (mm in)
 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
322

SENSING CHARACTERISTICS (TYPICAL) FIBER

SENSORS

LASER
EX-14□ Convergent reflective type SENSORS

PHOTO-
Sensing fields ELECTRIC
SENSORS
• Horizontal (left and right) direction • Vertical (up and down) direction MICRO
PHOTO-
40 40 ELECTRIC
1.575 50 × 50 mm 1.969 × 1.969 in 1.575 SENSORS
Non-glossy paper
AREA
SENSORS
Setting distance L (mm in)

30 Setting distance L (mm in)

30
1.181 7 mm ℓ 1.181 50 × 50 mm LIGHT
0.276 in L 1.969 × 1.969 in CURTAINS /
White Non-glossy paper SAFETY
COMPONENTS
20 20
0.787 White 0.787 PRESSURE /
FLOW
SENSORS
10 10 INDUCTIVE
0.394 0.394 ℓ PROXIMITY
N4 7.75 SENSORS
N4 mm L
0.305 in
0 0 PARTICULAR
10 5 0 5 10 10 5 0 5 10 USE
SENSORS
0.394 0.197 0.197 0.394 0.394 0.197 0.197 0.394
Left Center Right Down Center Up
Operating point ℓ (mm in) SENSOR
Operating point ℓ (mm in) OPTIONS

Correlation between lightness and sensing range Correlation between material (50 × 50 mm 1.969 × 1.969 in) and sensing range SIMPLE
WIRE-SAVING
40 80 UNITS
1.575 The sensing region (typical) is 3.150 The bars in the graph indicate
represented by oblique lines the sensing range (typical) WIRE-SAVING
SYSTEMS
in the left figure. However, the 60 for the respective material.
Sensing range L (mm in)

30
Sensing range L (mm in)

1.181 sensitivity should be set with 2.362 However, there is a slight MEASURE-
MENT
enough margin because of variation in the sensing range SENSORS
20 slight variation in products. 40 depending on the product. STATIC
0.787 1.575
Sensing region
Further, if there is a reflective ELECTRICITY
PREVENTION
object (conveyor, etc.) in the DEVICES
10 20 background of the sensing LASER
0.394 0.787 MARKERS
10 object, since it affects the
0.394 sensing, separate it by more
convergent point

0 0

Distance to convergent point

N2 N4 N6 N8 Lightness shown on the left than twice the sensing range PLC
Black circuit board
Black rubber sheet
IC tray (Black)

Ceramic circuit board

White non-glossy paper
Stainless steel plate
Aluminum plate
(Hair line)
Aluminum-evaporated mirror
Glass epoxy printed circuit board
Distance to

Dark Lightness Light shown in the left graph.

may differ slightly from the HUMAN
(Green masked surface)

N1 N2 N3 N4 N5 N6 N7 N8 N9 actual object condition. MACHINE

INTERFACES
ENERGY
CONSUMPTION
VISUALIZATION
COMPONENTS

FA

PRECAUTIONS FOR PROPER USE

COMPONENTS
Refer to p.1458~ for general precautions.
MACHINE
VISION
SYSTEMS
Operation mode switch UV
• Never use this product as a sensing device (EX-15□, EX-15E□, EX-17□ and EX-17E□ only) CURING
SYSTEMS
for personnel protection.
• In case of using sensing devices for Operation mode switch
personnel protection, use products which L: Light-ON
meet laws and standards, such as OSHA, D: Dark-ON

ANSI or IEC etc., for personnel protection

applicable in each region or country. Operation indicator (Orange) Selection
Lights up when the output is Guide
ON. Amplifier
Mounting Built-in
Power Supply
Built-in
• In case of mounting on tapped holes (Unit: mm in) Switch Amplifier-
Description
position separated
Side sensing Front sensing

Sensing Light-ON mode is set when the switch is turned fully CX-400
Sensing 11 direction clockwise (L side).
direction 0.433 CY-100
Attached screw 11
Attached screw M2 × 0.4 0.016 hole [M2 (length 8 0.315)] 0.433 Dark-ON mode is set when the switch is turned fully EX-10
tapped, 6 0.157 deep M2 × 0.4 0.016 hole counterclockwise (D side).
[M2 (length 10 0.394)] EX-20
tapped, 7 0.276 deep
EX-30
The tightening torque should be 0.2 N·m or less.
Others EX-40
• In case of using attached screws and nuts (Unit: mm in)
• Do not use during the initial transient time (50 ms) CX-440
Side sensing Front sensing (EX-15□, EX-15E□, EX-17□, EX-17E□: 100 ms) after the EQ-30
Flat washers power supply is switched on.
Sensing EQ-500
11 Sensing direction • Excess bending of the cable or stress applied to the
direction
0.433 Nuts cable may disconnect the internal lead wire. MQ-W
Spring washers Attached screw 11
Attached screw [M2 (length 8 0.315)] 0.433 RX-LS200
[M2 (length 10 0.394)]
RX
Thickness of Thickness of
mounting plate: 2 0.079 or less mounting plate: 2.5 0.098 or less
RT-610
The tightening torque should be 0.2 N·m or less.
 323 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2

FIBER
SENSORS
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.

LASER
SENSORS EX-11□  EX-11S□  EX-13□  EX-13S□  EX-19□  EX-19S□ Sensor
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO- Stability
ELECTRIC 10
SENSORS 0.394 indicator 3.5
3.5 6.45 (Green) 0.138
AREA 0.138 10 2.1
SENSORS 2.1 0.394 5.5 0.254 Operation 0.083
0.083 5.5 0.217 indicator
0.217 1.75
LIGHT 0.069 (Orange)
CURTAINS / 1.75 0.069
SAFETY 1.75 1.5
COMPONENTS
1.75 0.069 0.069 0.059
PRESSURE /
FLOW
SENSORS
4 Beam- 4
INDUCTIVE 0.157 receiving 0.157
PROXIMITY 14.5 11 11 14.5
0.571 0.433 part 0.433 0.571
SENSORS

PARTICULAR
USE 4.5
SENSORS 4.5 Beam-
0.177 emitting 0.177
SENSOR part
OPTIONS 2-ø2.2 ø0.087 6.5 6.5 2-ø2.2 ø0.087
mounting holes 0.256 0.256
mounting holes
SIMPLE ø2.5 ø0.098 cable, 2 m 6.562 ft long ø2.5 ø0.098 cable, 2 m 6.562 ft long
WIRE-SAVING
UNITS

WIRE-SAVING Emitter Receiver

SYSTEMS

MEASURE-
MENT
SENSORS
EX-11E□  EX-11SE□  EX-13E□  EX-13SE□  EX-19E□ Sensor
STATIC
ELECTRICITY
PREVENTION
DEVICES

LASER
MARKERS Stability
indicator (Green)
10
PLC Operation 0.394
indicator (Orange) 6.45
10 0.254
HUMAN 0.394 4.5 4.5 1.75
MACHINE 1.75 0.069 0.177 0.177 0.069
INTERFACES 2.25 2.25 1.75 1.5
1.75 0.069 0.089 0.089 0.069 0.059
ENERGY
CONSUMPTION
VISUALIZATION
COMPONENTS 4 Beam-
0.157 Beam- 4
FA emitting receiving 0.157
14.5 11
COMPONENTS 0.571 0.433 part part 11 14.5
0.433 0.571
MACHINE
VISION
SYSTEMS 4.5 4.5
0.177 0.177
UV
CURING 2-ø2.2 ø0.087 6.5
SYSTEMS 6.5 2-ø2.2 ø0.087
mounting holes 0.256 0.256
4.2 4.2 mounting holes
ø2.5 ø0.098 cable, 2 m 6.562 ft long 0.165 0.165
ø2.5 ø0.098 cable, 2 m 6.562 ft long

Emitter Receiver

Selection
Guide
Amplifier EX-15  EX-17 Sensor EX-15E  EX-17E Sensor
Built-in
Power Supply
Built-in Emitter 10 Receiver Stability indicator (Green)
Emitter Receiver
Amplifier- 10 Stability indicator (Green) 10
0.394 Incident beam indicator (Orange)
separated 5.5 1.75 0.394 Incident beam indicator (Orange) 0.394
1.75 0.217 10 0.394 3.5 0.069 6.45 0.254
3.5 0.069 4.5
0.138 6.45 0.254 0.138 4.5 1.75 0.069
1.75 4 1.5 1.75 0.177 0.177 1.5
5.5 1.75
1.75
0.069 4 4 1.75 0.059
CX-400 2.1 0.069 0.157 0.217 0.069 0.059 2.1 0.157 2.25 2.25
0.157 0.069
0.069 0.083 0.089 0.089
0.083
CY-100 Beam- Beam- 4 0.157 11 Beam- Beam-
14.5 11 14.5 14.5 11 emitting receiving 11 14.5
0.571 0.433 emitting receiving 0.433 0.571 0.571 0.433 0.433 0.571
part part part part
EX-10 4.5 0.177 4.5 0.177
EX-20 4.5 4.5
0.177 0.177 4.2 4.2
EX-30 2-ø2.2 ø0.087 2-ø2.2 ø0.087 2-ø2.2 ø0.087 0.165 0.165 2-ø2.2 ø0.087
mounting holes 500 mounting holes
mounting holes 19.685 mounting holes 500
EX-40 19.685
ø2.5 ø0.098 cables
CX-440 15.2 0.598 ø2.5 ø0.098 cables
15.2 0.598
EQ-30
Operation indicator 19.2
(Orange) 0.756 Operation indicator 19.2
EQ-500 38 (Orange) 0.756
1.496 38
MQ-W
1.496
Operation mode switch
RX-LS200 Operation mode switch
ø3.8 ø0.150 cable,
RX ø3.8 ø0.150 cable,
2 m 6.562 ft long
2 m 6.562 ft long
RT-610 1 0.039 8
7 0.315 1 0.039 8
0.276 7 0.315
0.276
 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
324

DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website. FIBER
SENSORS

LASER
EX-14□ Sensor SENSORS

PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
13 SENSORS
0.512
6.45 Stability indicator AREA
0.254 SENSORS
2.75 (Green) 3.5
5 0.108 0.138 LIGHT
0.197 1.75 Operation 2.1
indicator (Orange) CURTAINS /
0.069 0.083 SAFETY
COMPONENTS
1.75 1.5
0.069 0.059 PRESSURE /
FLOW
SENSORS

INDUCTIVE
4.5 PROXIMITY
Beam- 0.177
11 14.5 SENSORS
receiving
part 0.433 0.571 PARTICULAR
USE
SENSORS
Beam-emitting part 4.5
0.177 SENSOR
OPTIONS
8
0.315 2-ø2.2 ø0.087 mounting holes SIMPLE
WIRE-SAVING
ø2.5 ø0.098 cable, UNITS
2 m 6.562 ft long
WIRE-SAVING
SYSTEMS

MEASURE-
MS-EX10-1 Sensor mounting bracket (Optional) MENT
SENSORS
STATIC
Assembly dimensions ELECTRICITY
PREVENTION
DEVICES
t 1.2 7.6 Mounting drawing with EX-14□
t 0.047 0.299 LASER
MARKERS
t 1.2 20 0.787 (0.7)
t 0.047 7.6 (0.028)
PLC
0.299
3.7
0.146 HUMAN
MACHINE
INTERFACES
3.7 3.5 (4.9)
0.146 0.138 (0.193) ENERGY
20 CONSUMPTION
22.75 0.896 VISUALIZATION
0.787 13 COMPONENTS
4-M2 × 0.4 0.016 6.5 8 3.5 0.512
0.256 0.315 0.138 FA
thru-hole threads 2-ø3.4 ø0.134 mounting holes 5 10.75
0.423
3.5 COMPONENTS
0.197 0.138
Beam- 8 1.25
0.315 (8.8) 0.049 MACHINE
emitting (0.346) VISION
part SYSTEMS
11 8 15
0.433 0.315 0.591 UV
Beam- 3 0.118 11 15 CURING
8 SYSTEMS
receiving 0.315 0.433 0.591
part
Material: Cold rolled carbon steel (SPCC)
(Uni-chrome plated) 4.25 0.167
Two M2 (length 4 mm 0.157 in) pan head screws are attached.
2-ø3.4 ø0.134 mounting holes

Selection
Guide
MS-EX10-2 Sensor mounting bracket (Optional) Amplifier
Built-in
Assembly dimensions Power Supply
t 1.2 Built-in
t 0.047 7.6
0.299 Mounting drawing with EX-11E□ and EX-13E□ Amplifier-
separated

6.25 (2.3)
7.6 (0.091)
0.246 t 1.2 0.299
t 0.047 CX-400

20 4.5 (7.45) CY-100

6.25
0.787 0.246 0.177 (0.293)
3.2 1.4
EX-10
0.126 0.055 (1.3)
(0.051) 3.2 EX-20
4 0.25 10 0.126 1.25
0.157 0.010 0.394 0.049 EX-30
1.4
11 8 15 0.055 EX-40
0.433 0.315 0.591
Beam- 2.5 0.098 CX-440
15 11 receiving 8
0.591 0.433 0.315 EQ-30
part
2-M2 × 0.4 0.016
thru-hole threads 8 3.5 EQ-500
0.315 0.138 4.25
0.167 MQ-W
Material: Cold rolled carbon steel (SPCC) 8 3.5
(Uni-chrome plated) 0.315 0.138 RX-LS200
20
Two M2 (length 8 mm 0.315 in) pan head screws are attached. 0.787 RX

RT-610
 325 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2

FIBER
SENSORS
DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.

LASER
SENSORS MS-EX10-3 Sensor mounting bracket (Optional)
PHOTO-
ELECTRIC 15 Assembly dimensions
SENSORS 0.591
MICRO Mounting drawing with EX-14□
PHOTO-
ELECTRIC 7 0.276
SENSORS 10.5 (2.75) 10.8 t 1.2
0.413 (0.108) 0.425 t 0.047
AREA
SENSORS
3.2 (0.7)
1.4 (0.028)
LIGHT 0.055 0.126
CURTAINS / 8
SAFETY t 1.2 0.315 4-M2 × 0.4 0.016
COMPONENTS thru-hole threads 3.5 10.5
t 0.047 0.138 0.413 3.2
PRESSURE /
FLOW Beam- 1.75 0.069 Beam- 0.126
13 7
SENSORS receiving part 0.512 emitting part
0.276
10.8 6.5 5 6.25 1.25
INDUCTIVE 0.049
PROXIMITY 0.425 0.256 0.197 0.246 1.4
SENSORS 0.055

PARTICULAR
USE 11 2 3 0.118
SENSORS 0.433 11 15 8
0.079 0.438 0.591 0.315
SENSOR Material: Cold rolled carbon steel (SPCC)
OPTIONS
(Uni-chrome plated) 4.25
SIMPLE Two M2 (length 4 mm 0.157 in) pan head screws and two M2 (length 8 mm 0.315 in) pan 0.167
WIRE-SAVING head screws are attached.
UNITS

WIRE-SAVING
SYSTEMS

MEASURE-
MENT MS-EX10-11 Sensor mounting bracket (Optional)
SENSORS
STATIC
ELECTRICITY
Assembly dimensions
PREVENTION
DEVICES Mounting drawing with EX-14□
LASER t 1.2 8.1
MARKERS t 0.047 0.319
20
0.787 (0.7)
t 1.2 8.1
PLC t 0.047 0.319 (0.028)

3.7 (4.9)
HUMAN 20
MACHINE 0.146 (0.193)
INTERFACES 0.787
4-M2 × 0.4 0.016 6.5 8 3.5
3.7 3.5 22.75
ENERGY thru-hole threads 0.256 0.315 0.138 1.4 3.2 0.896
0.146 0.138
CONSUMPTION
VISUALIZATION 0.055 0.126 13
0.512
COMPONENTS 5 3.5
0.197 10.75 0.423 0.138
FA 11 8 0.315
COMPONENTS 8 15
0.433 0.315 0.591 (9.3) 3.2 1.25
(0.366)
MACHINE 1.4 0.126 0.049
VISION 0.055
SYSTEMS 3.2 1.4 Beam-emitting part
UV 0.126 0.055
CURING 3 0.118
SYSTEMS 8 11 15
0.315 0.433 0.591
Beam-receiving part
Material: Stainless steel (SUS304)
Two M2 (length 4 mm 0.157 in) pan head screws [stainless steel (SUS304)] are attached. 4.25
1.4
0.055 0.167

3.2
Selection
0.126
Guide
Amplifier
Built-in
MS-EX10-12 Sensor mounting bracket (Optional)
Power Supply
Built-in
Amplifier- t 1.2 8.1 Assembly dimensions
separated t 0.047 0.319
Mounting drawing with EX-11E□ and EX-13E□
 
6.25 W  
CX-400 0.246 W
CY-100
20   
EX-10 0.787   
1.4
EX-20 0.055 3.2
0.126 

EX-30

    
EX-40 11 8 15    

0.433 0.315 0.591 
CX-440

EQ-30 2-M2 × 0.4 0.016 1.4 %HDP 

thru-hole threads 0.055   
UHFHLYLQJ 
EQ-500 3.2  
0.126 SDUW
MQ-W 8 3.5
0.315 0.138  
RX-LS200 Material: Stainless steel (SUS304)  

Two M2 (length 8 mm 0.315 in) pan head screws [stainless steel (SUS304)] are attached. 
RX
 
 
RT-610


 Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
326

DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website. FIBER
SENSORS

LASER
MS-EX10-13 Sensor mounting bracket (Optional) SENSORS

PHOTO-
Assembly dimensions ELECTRIC
SENSORS
7 Mounting drawing with EX-14□ MICRO
10.5 0.276 PHOTO-
0.413 3.2 0.126 ELECTRIC
(2.75) 10.8 t 1.2 SENSORS
1.4 0.055 (0.108) 0.425 t 0.047
1.4 AREA
0.055 3.2 0.126 SENSORS
8 (0.7)
0.315 (0.028) LIGHT
15 CURTAINS /
t 1.2 0.591 4-M2 × 0.4 0.016 SAFETY
COMPONENTS
t 0.047 thru-hole threads
PRESSURE /
FLOW
SENSORS

10.8 13 1.75 INDUCTIVE

6.5 0.256 0.512 0.069 3.5
0.425 0.138 PROXIMITY
5 6.25 10.5 SENSORS
0.197 0.246 0.413
1.25 7 PARTICULAR
11 2 0.049 0.276 1.4 3.2 USE
SENSORS
0.433 0.079 Beam-emitting 0.055 0.126
part SENSOR
Material: Stainless steel (SUS304) OPTIONS
3 0.118
Two M2 (length 4 mm 0.157 in) pan head screws [stainless steel (SUS304)] and two M2 11 15 8
(length 8 mm 0.315 in) pan head screws [stainless steel (SUS304)] are attached. Beam-receiving 0.433 0.591 0.315 SIMPLE
part WIRE-SAVING
UNITS

4.25 1.4 WIRE-SAVING

0.167 0.055 SYSTEMS

MEASURE-
3.2 MENT
0.126 SENSORS
STATIC
ELECTRICITY
PREVENTION
DEVICES

LASER
MARKERS

PLC

HUMAN
MACHINE
INTERFACES
ENERGY
CONSUMPTION
VISUALIZATION
COMPONENTS

FA
COMPONENTS

MACHINE
VISION
SYSTEMS

UV
CURING
SYSTEMS

Selection
Guide
Amplifier
Built-in
Power Supply
Built-in
Amplifier-
separated

CX-400

CY-100

EX-10

EX-20

EX-30

EX-40

CX-440

EQ-30

EQ-500

MQ-W

RX-LS200

RX

RT-610