ANNUAL REPORT FOR 2021-22, 2022-2023.

Fabrication Work Done during period 01-04-2021 to 31-03-2022 and 01-04-2022 to 31-03-2023

SR. NO JOB NAME OPERATION PERFORMED JOB PHOTO

61 3D Printing of component as per CAD file Sent Through Email 3D PRINTING
62 Mouth Fittng, Fitting attachment for 3D Printing 3D PRINTING
63 Quartz Cuvette Cutting from one side Machining
64 Fabrication of workpiece as per drawing in aluminium Machining
65 To increase the hole size Motor cupler Machining
66 Fabrication of connector in brass Machining
68 Inpection of lens L-7, L-8, L-7 calibration Work Machining
69 Fabrication of lens-1, Lens-2, Lens-3, Lens-4 as per drawing Machining
70 Fabrication of tray of internet switchbox Machining
71 Cutting ss strip of heat sink Machining
72 Required Profile measurement of a concave surface on MAHR [6 liner scans requird at 30 Digri Rotation Measurement
73 Through Hole or Drilling though the tadepter(SMA) Machining
74 To remove specified matrerial from the job as per drawing Machining
75 Operation according to attached Drawing Machining
76 Fabrication of cuvette holder Machining
77 Turning of a cylendrical Rod on a plate as per drawing Machining
78 Models Blanks Cutting as per Drawing & Also Engineering Machining
79 Assembly of Periscope optics elements Machining
80 Fabrication as per Drawing Machining
81 Fabrication as per Drawing Machining
82 Fabrication of Frame bars as per attached Drg. Machining
83 FAbriction of Front Mount Hub Machining
84 3D Printing of following Components as per Drg. 3D PRINTING
85 Fabrication Of lamp Heat Sink Machining
86 The Below arm is presently vadutaken by shri Kumhar lal Machining
87 Fabrictaiom of Fluride- V3 Cuvette Holder With Plate Machining
88 Design of Fluride- V4 Cuvette Holder Designing
89 Design of Fluride- V2 Cuvette Holder Designing
90 Design of Fluride- V1 Cuvette Holder Designing
91 Optical SND system Assembled Alignment work Lens Assembly Fitting
92 Fabrication of heat sink adapter Machining
93 Design of heat sink Adapter Designing
94 Fabrictaiom of Fluride- V2 Cuvette Holder With Plate Machining
95 Fabrictaiom of Fluride- V1 Cuvette Holder With Plate Machining
96 Fabrictaiom of Fluride- V4 Cuvette Holder With Plate Machining
97 Design of Camera Stand Designing
98 Design of lens Cover for Camera Designing
99 Cutting BK-7 Glass Slab make 2 glass slab Machining
100 Step Turing of Aluminium Job Machining
101 3D Printing of support clamp for TFt 3 D Printing
102 Fabrication of curcular disk Plate Machining
103 Required of Lakhvinder in seismic observating for work Observating
104 Fabrication of Front mount hub & bundle Holder as per attached Drawing Machining
105 Fabrication of Euiptical & Plate Euiptical Regeltor Machining
106 Design of Fluride Detection System Designing
107 Fabrication as per Drg Machining
108 Welding Training to (i) sh. Satya Pratap & Dhairya Singh Training
109 laser Cutting training to (i) sh. Satya Pratap & Dhairya Singh Training
110 Precision Lathe training to (i) sh. Satya Pratap & Dhairya Singh Training
111 Design of PH & Conductivity sensor Holder Designing
112 Glass Grinding Disk & Glass Plate Of cutting Machining
113 Designing Of metalic base Plate Designing
114 4 Drill on Provided Part as per Drawing Machining
115 Slots On Aluminium Sqaure Pipes as per sketch attached & discuss with Indetor Machining
116 Fabrication of Metalic Base Plate. Machining
117 3D Printing Job 3 D Printing
118 3 D Printing Job 3 D Printing
119 3D Printing Job 3 D Printing
120 Fabrication of filter Holder as per attached drawing Machining
121 Assembly/ Modification Of LLTV Camera assembly and Mount Machining
122 Doublet Convex Lens ( Focal Length) Machining
123 Fixing Power Hacksaw Blade. Fitting
124 Designing of Cuvette Holder (v5) and Adopter. Designing
125 Welding of Tractor driven water TAnk. Urgent Work Please. Machining
126 Welding work of Tractor Driver shrub master Augle and chasses urgent work. Machining
127 Designing of cuvette holder (v6) Designing
128 Fabrication of cuvette holder (v5) Machining
129 Design Of Acraylic Stand. Designing
130 Acraylic Stand Cutting in Laser Cutting as per Designing Machining
131 Fabrication and assembly of linier Stages mount (as per Drawing Attached) Machining
132 Fabrication of base Plate For v4 Machining
133 Fabrication of cuvette holder (v6) Machining
134 To Fabrication a Aluminium Clamps As per Drawing. Machining
135 Through Drill on DRW SS gate matting partas per drawing Machining
136 Requirement of Fibersheet ------
137 Milling and Drilling of aliminium Plate Machining
138 Fabrication of Sensor Holder For PH & EC. Machining
139 Optical assembly of eye piece module Assembly
140 Fabrication of 2 lens 0of Dristiswipe Glasses as per drg. Machining
141 Required the service of Lakhvinder for Portable Seismograph in the observatory on in a week Observatory work
142 3D Printing Job Plastic Surge Parts 3 D Printing
143 Design of 3 D Printing of chassis for TPC meter (Designmodification) 3 D Printing
144 Fittness of Recording Camera Machining
145 Design and Fabrication PCS mounting plates Designing
146 Modification and fitnet of camera Bracket Machining
147 Please Fabricate ladder of M.S Square Pipe with length of Machining
148 Plaro Convex Lens BK- 7 Substrates Machining
149 Plaro Convex Lens BK- 7 Substrates Machining
150 Polishing of Glasses Machining
151 3 D Printing Upper half & lower Half Front Covering Outer Covering 3 D Printing
152 3 D Printing of following parts wide arm final centreroller 3 D Printing
153 Fabrication alu Angles with following Spaces length Machining
154 Fabrication of collimeter assembly of as per drawing Machining
155 Fabrication of aluminium bars Drg Attached Machining
156 Fabrication the following 3 D Printer reffector Plate elliptical Reffectpor Machining
157 Fabrication of CDAMP for sensor Holder Machining
158 Fabrication of Clamp Thread for Sensor (Holder) Machining
159 Fabrication of connector for Sensor Flowcelf Machining
160 Requirement the service of Lakhvinder in Seismiie Observatory For Observation Observation
161 No's Sensor Flowcelf Machining Modification( Highlighted Operation in Drg. Machining
162 Fabrication of lamp Holder Machining
163 Modification of lamp Holder With mating part and discussion with Indentor Machining
164 FAbrication of Modified Cuvette Holder Machining
165 Grinding of Cuvette Machining
166 Laser Cutting Operation is Required On acrylic Sheet of Specified Dimention In Alloted Drg. Machining
167 Laser Cutting Operation is Required On acrylic Sheet of Specified Dimention In Alloted Drg. Machining
169 Required Laser Cutting Operation On acrylic Sheet of Specified Dimention In Alloted Drg. Machining
Threaded and a Small Cut as per Drg In the Workpice Which will be Provided Fabrication as per Drg in the
170 aluminium sheet Machining
171 Developement of flate Glass Disk for Mirror Aplications Machining
172 Aluminium Samples Cutting From Rod Machining
173 3D printing of mount fitting 01 no., pump ava-03 nos.,16 mm roller -03 nos, measurement circle- 01 no. 3D PRINTING
174 Fabrication of locking ring 25 mm Machining
175 Fabrication of sensor holder 5 nos. Machining
176 Fabrication of locking ring 13 mm Machining
177 Fabrication of sensor cap Machining
178 Fabrication of optical mirrors , mirror-d-68, mirror-d-44 ( one each) Machining
179 3D printing of tpc meter prototype 3D PRINTING
Fabrication of RPT components, DMD housing, DMD stopper,spacer 4.2, vi-plh-li spacer, vi -plh-ls-l3 stopper,
180 vi project lens housing,vi-plh-l2 spacer 3D PRINTING
181 Fabrication of closing cap Machining
182 3d printing of lap light component- joint locking cap,lockin pinknurling,joint version,main housing,poloriser cover 3D PRINTING
183 PMMA sheet cutting as per dwg. Machining
184 Optical fabrication of circular flat Dia 50x10 mm, glass bk-7 Machining
185 Recessing & threading tool modification Machining
186 Fabrication of RPT for pcb& dmd housing 3D PRINTING
187 Drilling for limit switch assembly& cuttting of aluminium plate as per dwg. Machining
188 Fabrication of DMD optical 4 lens Machining
189 Room no. 25 door is not closing properly istc shop welding
190 To study about development of led based solar simulator
191 Fabrication of plate Machining
192 Cutting ofdurhans tube glass Machining
193 Mechanical assembly of plastic surge(prototype) Assembly
194 Designing of online nitrate sensor Designing
195 Fabrication of job Machining
196 3D printing job 3D PRINTING
197 3D printing of LAP light joint 3D PRINTING
198 Modification of sample holder for fds & sma tapping in the presence of indentor Machining
199 For smoking & preservation of drum sheets of portable analog seismographic csio seismic observatory Device Operating
200 Modification as per dwg. & fabrication of aluminium component as per dwg. Machining
201 Polishing of the glass suitable for holography blank size 345x150x11 mm Machining
202 Polishing the surface of prism have 90 degree angle Machining
203 Service reuired ( purchase of plumbing items) Man power attachment
204 Replacement of oxygen gas cylinder with filled oxygen gas cylinder
205 Design modificaton of flowcell for EC & PH sensor Designing
206 Fabrication of Antenna cap in 3d printing 3D PRINTING
207 Inspection of various type gasket of drogue led light & other mechanical assembly project work Inspection work
208 Lappong of cast iron tool close tolerance for better grinding of glass Machining
209 Grindinf & polishing of micro rod Machining
210 Mirror coating Machining
211 Cutting of polycarbonate sheet to size 50x50 mm Machining
212 RPT fabrication Machining
213 Fabrication of 16 components Machining
214 3D Printing of following model,TLL housing,base plate, retainer, housing, cover, 3D PRINTING
215 Fabrication as per drawing Machining
216 Slot Cutting as per drawing Machining
217 Glass cutting of Duohoms tube size 13.5 mm Machining
218 Fabrication of the parts as per drawing attached Machining
219 Fabrication of the housing as per drawing attached Machining
220 Fabrication of parts as per attached drawings Holders for lens Machining
221 Fabrication of gland part as per drawing Machining
222 Lappong of cast iron tool close tolerance for better grinding of glass Lapping
223 Modification of 3D printing parts(milling) Machining
224 Designing of tubidity sensor chessis Designing
225 Drafting of mechanical casting for PCB assembly Drafting
226 Designing of multiangle tubidity cuvette Designing
227 Cutting and threading in a pipe (195 mm), Inner & outer Thread Machining
228 Aluminium sheet 12" x 6" ( 24 nos.) Electrical department Machining
229 Fabrication of parts as per attached drawings Machining
230 Require the service of Mr. Lakhwinder in the seismic observatory Man Power attachment
231 Require the service of Mr. Lakhwinder in the seismic observatory Man Power attachment
232 Reduction of thickness of part as per drawing Machining
233 Assembly of Drishti Scope Assembly
234 Making of holes on angle LED light of volleyball court Machining
235 Printing of parts (3D printing) 3D PRINTING
236 Plastic 3D printing as per drawing 3D PRINTING
237 Fabrication of 16 components Machining
238 3D printing of rear cover 3D PRINTING
239 3D printing of rear cover 3D PRINTING
240 3D printing of bottom plate 10ACL 3D PRINTING
241 3D printing of plastic mouth fitting new rack part 3D PRINTING
242 RPT fabrication Machining
243 ABS made of high resolution & good finishing 3d printing 3D PRINTING
244 Fabrication of antena cap Machining
245 Fabrication of nitrate sensor 3D PRINTING
246 3D printing of 2 parts 3D PRINTING
247 Fabrication of components as per attached model Machining
248 As Per design provided 3D PRINTING
249 3D printing as per attached file 3D PRINTING
250 As per attached drawing 3D PRINTING
251 Project prototype for the diagnosis of CS 3D PRINTING
252 3d printing of 3 components (solidworks iges & stl files attached) 3D PRINTING
253 Designing of chlorine sensor prototype Designing
254 Pinion & rack as per drawings 3D PRINTING
255 Screen cover as per drawing 3D PRINTING
256 As per attached drawing 3D PRINTING
257 Pinion shaft sub assembly 3 Set Machining
258 Housing engineering drawing of existing chessis Machining
259 Fitting work Fitting work
260 Tapping drilling & fall assembly Machining & Assembly
261 Dismantling & shifting of electostatic coating system from 2nd floor to ground floor Dismantling work
262 Cutting of 2 slots in a sheet metal casing to fit the handle Machining
263 Square as per drawing 50x40 mm with 5x5mm & 10x 10mm window 3D PRINTING
264 Square as per drawing 50x40 mm with 5x5mm & 10x 10mm window 3D PRINTING
265 Filter array A13, 3set ( lathe work) Machining
266 MBS main housing assembly Machining
267 Machining of water filter as per drawing (3 parts) Machining
268 Relay lens mount Machining
269 Drilling & boring in brass work gear and spacermatvhing of both parts Machining
270 Schmidt prism mount assembly qty 3 sets Machining
271 Fabrication of wedge plates Machining
272 to make rectangular slit of size 197x50 mm Machining
273 Vibration motor holder sheet Machining
274 Filter array A13, 3set ( milling work) Machining
275 Machining , drilling of trey movement plate as per drawing Machining
276 Hardware chassis design of portable colorimeter Designing
277 To drive high power led with corresponding heat sink etc. Machining
278 Fabrication & assembly of panel led light 1 no. Machining
279 Fabrication & assembly of navigation led light (2 set) Machining
280 Printing of 2 parts as per stl files 3D PRINTING
281 Printing of parts as per drawing 3D PRINTING
282 3D printing of four part with ABS plastic 3D PRINTING
283 Machining of different component to form a play load assembly Machining
284 Drilling holes in three plates as per drawing Machining
285 Design of ragged shell for off the shelf EC/PH sensor Designing
286 New manifold design for csio test bed with standardized components Designing
287 Designing of flow injection analysis sampler Designing
288 Designing of membrane cap for existing prototype Designing
289 Installation of indigenous nitrate system at csio, iot test piolet Installation work
290 OLED interface with PCB & code updation
291 Raspberry PI Arduino interfacing & data display
292 Increasing the dia of one hole from 20 to 32 mm in aluminium plate Machining
293
294
295
296
297
298
299
300
301
302
303
304
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347