DRIVER INFORMATION & MULTIMEDIA

AUDIO, VISUAL & NAVIGATION SYSTEM

SECTION AV B

E
CONTENTS
BASE AUDIO Reference Value ......................................................18 F
Wiring Diagram - BASE AUDIO - ............................20
BASIC INSPECTION .................................... 4
SYMPTOM DIAGNOSIS .............................. 25 G
DIAGNOSIS AND REPAIR WORKFLOW .......... 4
Work Flow ................................................................. 4 AUDIO SYSTEM ............................................... 25
Symptom Table .......................................................25
FUNCTION DIAGNOSIS ............................... 6 H
NORMAL OPERATING CONDITION ............... 26
AUDIO SYSTEM .................................................. 6 Description ...............................................................26
System Diagram ........................................................ 6
PRECAUTION .............................................. 27 I
System Description ................................................... 6
Component Parts Location ........................................ 6
Component Description ............................................. 7
PRECAUTIONS ................................................. 27
J
FOR USA AND CANADA ..........................................27
DIAGNOSIS SYSTEM (AUDIO UNIT) ................. 8
FOR USA AND CANADA : Precaution for Supple-
Diagnosis Description ............................................... 8
mental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER" ............................27 K
COMPONENT DIAGNOSIS ......................... 11
POWER SUPPLY AND GROUND CIRCUIT ......11 FOR MEXICO .............................................................27
FOR MEXICO : Precaution for Supplemental Re-
L
AUDIO UNIT .............................................................. 11 straint System (SRS) "AIR BAG" and "SEAT BELT
AUDIO UNIT : Diagnosis Procedure ....................... 11 PRE-TENSIONER" ..................................................27

STEERING SWITCH SIGNAL A CIRCUIT .........12 PREPARATION ........................................... 28 M

Description .............................................................. 12
Diagnosis Procedure ............................................... 12 PREPARATION ................................................. 28
Component Inspection ............................................ 13 Commercial Service Tools .......................................28
AV
STEERING SWITCH SIGNAL B CIRCUIT .........14 ON-VEHICLE REPAIR ................................. 29
Description .............................................................. 14
Diagnosis Procedure ............................................... 14
AUDIO UNIT ...................................................... 29 O
Component Inspection ............................................ 15 Exploded View .........................................................29
Removal and Installation .........................................29
STEERING SWITCH SIGNAL GND CIRCUIT....16 P
Description .............................................................. 16
TWEETER ......................................................... 30
Exploded View .........................................................30
Diagnosis Procedure ............................................... 16
Removal and Installation .........................................30
Component Inspection ............................................ 16
FRONT SPEAKER ............................................ 31
ECU DIAGNOSIS ......................................... 18
Exploded View .........................................................31
AUDIO UNIT .......................................................18 Removal and Installation .........................................31

Revision: 2008 August AV-1 2009 Rogue

REAR SPEAKER ............................................... 32 STEERING SWITCH SIGNAL B CIRCUIT ........ 54
Exploded View ........................................................ 32 Description .............................................................. 54
Removal and Installation ........................................ 32 Diagnosis Procedure ............................................... 54
Component Inspection ............................................ 55
STEERING SWITCH .......................................... 33
Exploded View ........................................................ 33 STEERING SWITCH SIGNAL GND CIRCUIT... 56
Removal and Installation ........................................ 33 Description .............................................................. 56
Diagnosis Procedure ............................................... 56
RADIO ANTENNA ............................................. 34 Component Inspection ............................................ 56
Exploded View ........................................................ 34
Removal and Installation ........................................ 34 STEERING SWITCH SIGNAL A CIRCUIT
(STEERING SWITCH TO TEL ADAPTER
ANTENNA FEEDER .......................................... 35 UNIT) .................................................................. 58
Location of Antenna ................................................ 35 Description .............................................................. 58
BOSE AUDIO Diagnosis Procedure ............................................... 58
Component Inspection ............................................ 59
BASIC INSPECTION ................................... 36
STEERING SWITCH SIGNAL B CIRCUIT
DIAGNOSIS AND REPAIR WORKFLOW ......... 36
(STEERING SWITCH TO TEL ADAPTER
Work Flow ............................................................... 36
UNIT) .................................................................. 60
FUNCTION DIAGNOSIS ............................. 38 Description .............................................................. 60
Diagnosis Procedure ............................................... 60
AUDIO SYSTEM ................................................ 38 Component Inspection ............................................ 61
System Diagram ..................................................... 38
System Description ................................................. 38 STEERING SWITCH SIGNAL GND CIRCUIT
Component Parts Location ..................................... 39 (STEERING SWITCH TO TEL ADAPTER
Component Description .......................................... 39 UNIT) .................................................................. 62
Description .............................................................. 62
HANDS-FREE PHONE SYSTEM ...................... 41 Diagnosis Procedure ............................................... 62
System Diagram ..................................................... 41 Component Inspection ............................................ 62
System Description ................................................. 41
Component Parts Location ..................................... 42 STEERING SWITCH SIGNAL A CIRCUIT
Component Description .......................................... 42 (TEL ADAPTER UNIT TO AUDIO UNIT) .......... 64
Description .............................................................. 64
DIAGNOSIS SYSTEM (AUDIO UNIT) ............... 44 Diagnosis Procedure ............................................... 64
Diagnosis Description ............................................. 44
STEERING SWITCH SIGNAL B CIRCUIT
DIAGNOSIS SYSTEM (TEL ADAPTER UNIT)... 47 (TEL ADAPTER UNIT TO AUDIO UNIT) .......... 65
Diagnosis Description ............................................. 47 Description .............................................................. 65
Diagnosis Procedure ............................................... 65
COMPONENT DIAGNOSIS ........................ 49
STEERING SWITCH SIGNAL GND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT ..... 49
(TEL ADAPTER UNIT TO AUDIO UNIT) .......... 66
AUDIO UNIT .............................................................. 49 Description .............................................................. 66
AUDIO UNIT : Diagnosis Procedure ...................... 49 Diagnosis Procedure ............................................... 66

BOSE AMP. ............................................................... 49 COMMUNICATION SIGNAL CIRCUIT .............. 67

BOSE AMP. : Diagnosis Procedure ....................... 49 Description .............................................................. 67
Diagnosis Procedure ............................................... 67
SATELLITE RADIO TUNER ..................................... 50
SATELLITE RADIO TUNER : Diagnosis Proce- REQUEST SIGNAL CIRCUIT (SAT TO AU-
dure ........................................................................ 50 DIO) .................................................................... 69
Description .............................................................. 69
TEL ADAPTER UNIT ................................................ 50
Diagnosis Procedure ............................................... 69
TEL ADAPTER UNIT : Diagnosis Procedure ......... 50
AMP. ON SIGNAL CIRCUIT .............................. 71
STEERING SWITCH SIGNAL A CIRCUIT ........ 52
Description .............................................................. 71
Description .............................................................. 52
Diagnosis Procedure ............................................... 71
Diagnosis Procedure .............................................. 52
Component Inspection ............................................ 53 WOOFER AMP. ON SIGNAL CIRCUIT ............ 72
Description .............................................................. 72

Revision: 2008 August AV-2 2009 Rogue

 Diagnosis Procedure ............................................... 72 PREPARATION ............................................... 149
Commercial Service Tools ..................................... 149 A
MICROPHONE SIGNAL CIRCUIT .....................73
Description .............................................................. 73 ON-VEHICLE REPAIR ............................... 150
Diagnosis Procedure ............................................... 73
AUDIO UNIT .................................................... 150 B
TELEPHONE ON SIGNAL CIRCUIT .................75 Exploded View ....................................................... 150
Description .............................................................. 75 Removal and Installation ....................................... 150
Diagnosis Procedure ............................................... 75 C
BOSE AMP. ..................................................... 151
ECU DIAGNOSIS ......................................... 76 Exploded View ....................................................... 151
Removal and Installation ....................................... 151
AUDIO UNIT .......................................................76 D
Reference Value ..................................................... 76 TWEETER ....................................................... 152
Wiring Diagram - BOSE AUDIO - ............................ 80 Exploded View ....................................................... 152
Removal and Installation ....................................... 152 E
BOSE AMP. ........................................................91
Reference Value ..................................................... 91 CENTER SPEAKER ........................................ 153
Wiring Diagram - BOSE AUDIO - ............................ 94 Exploded View ....................................................... 153
Removal and Installation ....................................... 153 F
WOOFER .......................................................... 105
Reference Value ................................................... 105 FRONT SPEAKER .......................................... 154
Wiring Diagram - BOSE AUDIO - .......................... 106 Exploded View ....................................................... 154 G
Removal and Installation ....................................... 154
SATELLITE RADIO TUNER ............................ 117
Reference Value ................................................... 117 REAR SPEAKER ............................................ 155
Wiring Diagram - BOSE AUDIO - .......................... 119 Exploded View ....................................................... 155 H
Removal and Installation ....................................... 155
TEL ADAPTER UNIT ....................................... 130
Reference Value ................................................... 130 WOOFER ......................................................... 156 I
Wiring Diagram - BOSE AUDIO - .......................... 133 Exploded View ....................................................... 156
Removal and Installation ....................................... 156
SYMPTOM DIAGNOSIS ............................ 144
SATELLITE RADIO TUNER ........................... 157 J
AUDIO SYSTEM SYMPTOMS ......................... 144 Exploded View ....................................................... 157
Symptom Table ..................................................... 144 Removal and Installation ....................................... 157
HANS-FREE PHONE SYMPTOMS .................. 145 K
RADIO & SATELLITE RADIO ANTENNA ...... 158
Symptom Table ..................................................... 145 Exploded View ....................................................... 158
Removal and Installation ....................................... 158
NORMAL OPERATING CONDITION ............... 147 L
Description ............................................................ 147 STEERING SWITCH ....................................... 159
Exploded View ....................................................... 159
PRECAUTION ............................................ 148 Removal and Installation ....................................... 159 M
PRECAUTIONS ................................................ 148 MICROPHONE ................................................ 160
FOR USA AND CANADA ........................................ 148 Exploded View ....................................................... 160
FOR USA AND CANADA : Precaution for Supple- Removal and Installation ....................................... 160 AV
mental Restraint System (SRS) "AIR BAG" and
TEL ADAPTER UNIT ...................................... 161
"SEAT BELT PRE-TENSIONER" .......................... 148
Exploded View ....................................................... 161
O
FOR MEXICO .......................................................... 148 Removal and Installation ....................................... 161
FOR MEXICO : Precaution for Supplemental Re-
straint System (SRS) "AIR BAG" and "SEAT BELT
TEL ANTENNA ............................................... 162
Exploded View ....................................................... 162 P
PRE-TENSIONER" ............................................... 148
Removal and Installation ....................................... 162
PREPARATION ......................................... 149
ANTENNA FEEDER ........................................ 163
Location of Antenna ............................................... 163

Revision: 2008 August AV-3 2009 Rogue

 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [BASE AUDIO]

BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000004235098

OVERALL SEQUENCE

JSNIA0669GB

Reference 1 ··· Refer to AV-25, "Symptom Table".

DETAILED FLOW
1.CHECK SYMPTOM
Check the malfunction symptoms by performing the following items.
• Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred).
• Check the symptom.

>> GO TO 2.
2.PERFORM DIAGNOSIS BY SYMPTOM
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to AV-25, "Symptom Table".

>> GO TO 3.
3.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace the malfunctioning parts.

>> GO TO 4.
4.FINAL CHECK
Revision: 2008 August AV-4 2009 Rogue
 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [BASE AUDIO]
Perform the operation to check that the malfunction symptom is solved or any other symptoms are present.
Is there any symptom? A
YES >> GO TO 2.
NO >> INSPECTION END
B

AV

Revision: 2008 August AV-5 2009 Rogue

 AUDIO SYSTEM
< FUNCTION DIAGNOSIS > [BASE AUDIO]

FUNCTION DIAGNOSIS
AUDIO SYSTEM
System Diagram INFOID:0000000004235099

JSNIA0668GB

System Description INFOID:0000000004235100

AUDIO SYSTEM
Audio functions

AM/FM radio
CD/6CD
• Radio signal are received by radio antenna, next it is amplified by antenna amp., and finally it is input to
audio unit. (Antenna amp. is built into radio antenna.)
• Audio unit outputs the audio signal to each speaker.
SPEED SENSITIVE VOLUME (6CD MODELS)
• Volume level of this system gone up and down automatically in proportion to the vehicle speed.
• The control level can be selected by the customer.
Component Parts Location INFOID:0000000004235101

JSNIA0723ZZ

1. Tweeter RH 2. Tweeter LH 3. Front speaker LH

4. Rear speaker LH 5. Radio antenna 6. Rear speaker RH
7. Front speaker RH 8. Steering switch 9. Audio unit

Revision: 2008 August AV-6 2009 Rogue

 AUDIO SYSTEM
< FUNCTION DIAGNOSIS > [BASE AUDIO]
Component Description INFOID:0000000004235102

Part name Description

Audio unit Controls audio system functions. B
• Outputs sound signal from audio unit.
Front speaker
• Outputs high, mid and low range sounds.
• Outputs sound signal from audio unit. C
Tweeter
• Outputs high range sounds.
• Outputs sound signal from audio unit.
Rear speaker
• Outputs high, mid and low range sounds. D
• Radio signal received by radio antenna is amplified and sent to audio unit.
Radio antenna (Built-in antenna amp.)
• Power (antenna amp. ON signal) is supplied from audio unit.
• Each audio operation can be operated. E
Steering switch
• Steering switch signal (operation signal) is output to audio unit.

AV

Revision: 2008 August AV-7 2009 Rogue

 DIAGNOSIS SYSTEM (AUDIO UNIT)
< FUNCTION DIAGNOSIS > [BASE AUDIO]
DIAGNOSIS SYSTEM (AUDIO UNIT)
Diagnosis Description INFOID:0000000004235103

Self-diagnosis mode can check the following items.

• Audio unit hardware/software versions
• Continuity of each speaker channel
• Continuity of each audio unit switch
OPERATION PROCEDURE
1. Turn ignition switch to the ON position.
2. Turn the audio unit off.
3. While pressing the “AUDIO” button, turn the volume control dial
clockwise or counterclockwise 30 clicks or more. When the self-
diagnosis mode is started, a short beep will be heard.

AWNIA0026ZZ

4. Initially, all display segments will be illuminated.

ALNIA0019ZZ

Version Check
1. Press the “AUDIO” switch to enter version diagnostics. “Soft-
ware” (audio software version) is displayed.

ALNIA0020ZZ

Revision: 2008 August AV-8 2009 Rogue

 DIAGNOSIS SYSTEM (AUDIO UNIT)
< FUNCTION DIAGNOSIS > [BASE AUDIO]
2. Press the “AUDIO” switch again to display the “Hardware”
(audio hardware version). A

ALNIA0021ZZ

D
3. Press the “AUDIO” switch again to display the “CD Mech” (CD
mechanism version).
E

G
ALNIA0022ZZ

4. Press the “AUDIO” switch again to display the “SDARS” (satel- H

lite radio version).

K
ALNIA0023ZZ

Channel Check Diagnostics

L
When all segments are illuminated, press the “TUNE” up switch to
enter channel check diagnostics. The self-diagnostic function will
then send a tone to each channel (FL, RL, RR, FR) for 1 second.
M

AV

O
ALNIA0024ZZ

Button Check Diagnostics

P

Revision: 2008 August AV-9 2009 Rogue

 DIAGNOSIS SYSTEM (AUDIO UNIT)
< FUNCTION DIAGNOSIS > [BASE AUDIO]
When all segments are illuminated, press the “TUNE” down switch to
enter button check diagnostics. When each audio unit switch is
pressed, a tone will sound and the switch name will be displayed.

ALNIA0025ZZ

Revision: 2008 August AV-10 2009 Rogue

 POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS > [BASE AUDIO]

COMPONENT DIAGNOSIS A
POWER SUPPLY AND GROUND CIRCUIT
AUDIO UNIT
B
AUDIO UNIT : Diagnosis Procedure INFOID:0000000004235104

1.CHECK FUSE C
Check that the following fuses of the audio unit are not blown.

D
Power source Fuse No.
Battery 35
Ignition switch ACC or ON 20 E
Is inspection result OK?
YES >> GO TO 2.
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. F
2.CHECK AUDIO UNIT POWER SUPPLY CIRCUIT
Check voltage between the audio unit and ground.
G
Signal name Connector No. Terminal No. Ignition switch position Voltage
Battery power supply M46 19 OFF Battery voltage
H
ACC power supply M46 7 ACC Battery voltage
Is inspection result OK?
YES >> INSPECTION END I
NO >> Check harness between audio unit and fuse.

AV

Revision: 2008 August AV-11 2009 Rogue

 STEERING SWITCH SIGNAL A CIRCUIT
< COMPONENT DIAGNOSIS > [BASE AUDIO]
STEERING SWITCH SIGNAL A CIRCUIT
Description INFOID:0000000004235105

Transmits the steering switch signal to audio unit.

Diagnosis Procedure INFOID:0000000004235106

1.CHECK STEERING SWITCH SIGNAL A CIRCUIT

1. Turn ignition switch OFF.
2. Disconnect audio unit connector and spiral cable connector.
3. Check continuity between audio unit harness connector and spiral cable harness connector.

Audio unit Spiral cable

Continuity
Connector Terminal Connector Terminal
M46 6 M33 24 Existed
4. Check continuity between audio unit harness connector.

Audio unit
Continuity
Connector Terminal Ground
M46 6 Not existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK SPIRAL CABLE
Check spiral cable.
Is inspection result OK?
YES >> GO TO 3.
NO >> Replace spiral cable.
3.CHECK AUDIO UNIT VOLTAGE
1. Connect audio unit connector and spiral cable connector.
2. Turn ignition switch ON.
3. Check voltage between audio unit harness connector.

(+) (−)
Voltage
Audio unit Audio unit
(Approx.)
Connector Terminal Connector Terminal
M46 6 M46 15 3.3 V
Is inspection result OK?
YES >> GO TO 4.
NO >> Replace audio unit.
4.CHECK STEERING SWITCH
1. Turn ignition switch ON.
2. Check steering switch. Refer to AV-13, "Component Inspection".
Is inspection result OK?
YES >> INSPECTION END
NO >> Replace steering switch.

Revision: 2008 August AV-12 2009 Rogue

 STEERING SWITCH SIGNAL A CIRCUIT
< COMPONENT DIAGNOSIS > [BASE AUDIO]
Component Inspection INFOID:0000000004235107

A
Measure the resistance between the steering switch connector.
Standard

Steering switch
B
Resistance
Condition
Terminal Terminal Ω

VOL UP switch ON 645 – 659

C
20 SEEK UP switch ON 163 – 167
SOURCE switch ON 0
17
VOL DOWN switch ON 645 – 659 D
16 SEEK DOWN switch ON 163 – 167
POWER switch ON 0 JSNIA0673GB
E

AV

Revision: 2008 August AV-13 2009 Rogue

 STEERING SWITCH SIGNAL B CIRCUIT
< COMPONENT DIAGNOSIS > [BASE AUDIO]
STEERING SWITCH SIGNAL B CIRCUIT
Description INFOID:0000000004235108

Transmits the steering switch signal to audio unit.

Diagnosis Procedure INFOID:0000000004235109

1.CHECK STEERING SWITCH SIGNAL B CIRCUIT

1. Turn ignition switch OFF.
2. Disconnect audio unit connector and spiral cable connector.
3. Check continuity between audio unit harness connector and spiral cable harness connector.

Audio unit Spiral cable

Continuity
Connector Terminal Connector Terminal
M46 16 M33 32 Existed
4. Check continuity between audio unit harness connector.

Audio unit
Continuity
Connector Terminal Ground
M46 16 Not existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK SPIRAL CABLE
Check spiral cable.
Is inspection result OK?
YES >> GO TO 3.
NO >> Replace spiral cable.
3.CHECK AUDIO UNIT VOLTAGE
1. Connect audio unit connector and spiral cable connector.
2. Turn ignition switch ON.
3. Check voltage between audio unit harness connector.

(+) (−)
Voltage
Audio unit Audio unit
(Approx.)
Connector Terminal Connector Terminal
M46 16 M46 15 3.3 V
Is inspection result OK?
YES >> GO TO 4.
NO >> Replace audio unit.
4.CHECK STEERING SWITCH
1. Turn ignition switch ON.
2. Check steering switch. Refer to AV-15, "Component Inspection".
Is inspection result OK?
YES >> INSPECTION END
NO >> Replace steering switch.

Revision: 2008 August AV-14 2009 Rogue

 STEERING SWITCH SIGNAL B CIRCUIT
< COMPONENT DIAGNOSIS > [BASE AUDIO]
Component Inspection INFOID:0000000004235110

A
Measure the resistance between the steering switch connector.
Standard

Steering switch
B
Resistance
Condition
Terminal Terminal Ω

VOL UP switch ON 645 – 659

C
20 SEEK UP switch ON 163 – 167
SOURCE switch ON 0
17
VOL DOWN switch ON 645 – 659 D
16 SEEK DOWN switch ON 163 – 167
POWER switch ON 0 JSNIA0673GB
E

AV

Revision: 2008 August AV-15 2009 Rogue

 STEERING SWITCH SIGNAL GND CIRCUIT
< COMPONENT DIAGNOSIS > [BASE AUDIO]
STEERING SWITCH SIGNAL GND CIRCUIT
Description INFOID:0000000004235111

Transmits the steering switch signal to audio unit.

Diagnosis Procedure INFOID:0000000004235112

1.CHECK STEERING SWITCH SIGNAL GND CIRCUIT

1. Turn ignition switch OFF.
2. Disconnect audio unit connector and spiral cable connector.
3. Check continuity between audio unit harness connector and spiral cable harness connector.

Audio unit Spiral cable

Continuity
Connector Terminal Connector Terminal
M46 15 M33 31 Existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK SPIRAL CABLE
Check spiral cable.
Is inspection result OK?
YES >> GO TO 3.
NO >> Replace spiral cable.
3.CHECK GROUND CIRCUIT
1. Connect audio unit connector.
2. Check continuity between audio unit harness connector terminals 15 and ground.

Audio unit
Continuity
Connector Terminal Ground
M46 15 Existed
Is inspection result OK?
YES >> GO TO 4.
NO >> Replace audio unit.
4.CHECK STEERING SWITCH
1. Turn ignition switch ON.
2. Check steering switch. Refer to AV-16, "Component Inspection".
Is inspection result OK?
YES >> INSPECTION END
NO >> Replace steering switch.
Component Inspection INFOID:0000000004235113

Measure the resistance between the steering switch connector.

Revision: 2008 August AV-16 2009 Rogue

 STEERING SWITCH SIGNAL GND CIRCUIT
< COMPONENT DIAGNOSIS > [BASE AUDIO]
Standard

Steering switch Resistance

A
Condition
Terminal Terminal Ω

VOL UP switch ON 645 – 659

B
20 SEEK UP switch ON 163 – 167
SOURCE switch ON 0
17
VOL DOWN switch ON 645 – 659 C
16 SEEK DOWN switch ON 163 – 167
POWER switch ON 0 JSNIA0673GB

AV

Revision: 2008 August AV-17 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BASE AUDIO]

ECU DIAGNOSIS
AUDIO UNIT
Reference Value INFOID:0000000004235114

TERMINAL LAYOUT

JPNIA1434ZZ

PHYSICAL VALUES

Terminal
Description
(Wire color) Reference value
Condition
Input/ (Approx.)
+ – Signal name
Output

Ignition
2 3
Sound signal front LH Output switch Voice output
(R) (G)
ON

SKIB3609E

Ignition
4 5
Sound signal rear LH Output switch Voice output
(V) (LG)
ON

SKIB3609E

Keep pressing SOURCE

0V
switch

Ignition Keep pressing SEEK UP

6 15 1.1 V
Steering switch signal A Input switch switch
(W) (GR)
ON Keep pressing VOL UP
2.2 V
switch
Except for above 3.3 V
Ignition
7
Ground ACC power supply Input switch — Battery voltage
(SB)
ACC

Ignition
11 12
Sound signal front RH Output switch Voice output
(O) (W)
ON

SKIB3609E

Revision: 2008 August AV-18 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BASE AUDIO]
Terminal
Description
(Wire color) Reference value A
Condition
Input/ (Approx.)
+ – Signal name
Output
B

Ignition
13 14 C
Sound signal rear RH Output switch Voice output
(L) (P)
ON

SKIB3609E D
Ignition
15 Steering switch signal
Ground — switch — 0V
(GR) ground
ON E
Keep pressing POWER
0V
switch

Ignition Keep pressing SEEK F

16 15 1.1 V
Steering switch signal B Input switch DOWN switch
(O) (GR)
ON Keep pressing VOL DOWN
2.2 V
switch G
Except for above 3.3 V
NOTE:
The maximum voltage varies de- H
pending on the specification
(destination unit).
Ignition
18
Ground
Vehicle speed signal
Input switch
When vehicle speed is ap- I
(L) (8-pulse) prox. 40 km/h (25MPH)
ON

JSNIA0012GB

Ignition K
19
Ground Battery power supply Input switch — Battery voltage
(Y)
OFF
51 — Antenna signal Input — — —
L
Ignition
52 Ground Antenna amp. ON signal Output switch — 12.0 V
ON
M

AV

Revision: 2008 August AV-19 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BASE AUDIO]
Wiring Diagram - BASE AUDIO - INFOID:0000000004235115

JCNWM1637GB

Revision: 2008 August AV-20 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BASE AUDIO]

AV

JCNWM1638GB

Revision: 2008 August AV-21 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BASE AUDIO]

JCNWM1639GB

Revision: 2008 August AV-22 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BASE AUDIO]

AV

JCNWM1640GB

Revision: 2008 August AV-23 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BASE AUDIO]

JCNWM1641GB

Revision: 2008 August AV-24 2009 Rogue

 AUDIO SYSTEM
< SYMPTOM DIAGNOSIS > [BASE AUDIO]

SYMPTOM DIAGNOSIS A
AUDIO SYSTEM
Symptom Table INFOID:0000000004235116
B

AUDIO SYSTEM
C
Symptoms Check items Possible malfunction location / Action to take
Audio unit power supply and ground circuit.
No sound from all speakers.
Refer to AV-11, "AUDIO UNIT : Diagnosis Procedure".
Audio sound is not heard. D
Sound is not heard only from the
Sound signal circuit of malfunctioning system.
specific places.

RELATED TO STEERING SWITCH E

Symptoms Possible malfunction location / Action to take

Steering switch signal ground circuit. F
All steering switches are not operated.
Refer to AV-16, "Diagnosis Procedure".
Only specified switch cannot be operated. Replace steering switch.
“SEEK UP”, “VOL UP” and “SOURCE” switches are not oper- Steering switch signal A circuit. G
ated. Refer to AV-12, "Diagnosis Procedure".
“SEEK DOWN”, “VOL DOWN” and “POWER” switches are Steering switch signal B circuit.
not operated. Refer to AV-14, "Diagnosis Procedure". H

AV

Revision: 2008 August AV-25 2009 Rogue

 NORMAL OPERATING CONDITION
< SYMPTOM DIAGNOSIS > [BASE AUDIO]
NORMAL OPERATING CONDITION
Description INFOID:0000000004235117

RELATED TO AUDIO
• The majority of the audio malfunctions are the result of outside causes (bad CD, electromagnetic interfer-
ence, etc.). Check the symptoms below to diagnose the malfunction.
• The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check that noise is caused and/or changed by engine speed, ignition switch turned to each position, and
operation of each piece of electrical equipment. Then determine the cause.
NOTE:
• CD-R is not guaranteed to play because they can contain compressed audio (MP3, WMA) or could be incor-
rectly mastered by the customer on a computer. (6CD models)
• Check that the CDs carry the Compact Disc Logo. If not, the disc is not mastered to the red book Compact
Disc Standard and may not play.

Symptoms Cause and Counter measure

Check that the CD was inserted correctly.
Check that the CD is scratched or dirty.
Check that there is condensation inside the player, and if there is, wait until the condensation is
gone (about 1 hour) before using the player.
The player will play correctly after it returns to the normal temperature if there is a temperature
increase error.
Cannot play
Only the music CD files (CD-DA data) will be played if there is a mixture of music CD files (CD-
DA data) and MP3/WMA files on a CD. (6CD models)
Files with extensions other than “.MP3”, “.WMA”, “.mp3”, or “.wma” cannot be played. (6CD mod-
els)
Check that the finalization process, such as session close and disc close, is done for the disc.
Check that the CD is protected by copyright.
Poor sound quality Check that the CD is scratched or dirty.
It takes a relatively long time before If there are many folder or file levels on the MP3/WMA CD, or if it is a multi session disc, some
the music starts playing. time may be required before the music starts playing. (6CD models)
The songs do not play back in the The playback order is the order in which the files were written by the software, so the files might
desired order. not play in the desired order.
Noise resulting from variations in field strength, such as fading noise and multi-path noise, or external noise from trains and other
sources, is not a malfunction.
NOTE:
• Fading noise: This noise occurs because of variations in the field strength in a narrow range due to mountains or buildings blocking
the signal.
• Multi-path noise: This noise results from a time difference between the broadcast waves directly from the station arriving at the
antenna and the waves reflected by mountains or buildings.

Revision: 2008 August AV-26 2009 Rogue

 PRECAUTIONS
< PRECAUTION > [BASE AUDIO]

PRECAUTION A
PRECAUTIONS
FOR USA AND CANADA
B
FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000004678931

C
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS D
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual. E
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by F
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
G
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors. H
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and I
"SEAT BELT PRE-TENSIONER" INFOID:0000000004678932

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along J
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
K
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer. L
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”. M
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
AV

Revision: 2008 August AV-27 2009 Rogue

 PREPARATION
< PREPARATION > [BASE AUDIO]

PREPARATION
PREPARATION
Commercial Service Tools INFOID:0000000004235120

Tool name Description

Power tool Loosening bolts and nuts

PBIC0191E

Revision: 2008 August AV-28 2009 Rogue

 AUDIO UNIT
< ON-VEHICLE REPAIR > [BASE AUDIO]

ON-VEHICLE REPAIR A
AUDIO UNIT
Exploded View INFOID:0000000004235121
B

JSNIA0709ZZ E

1. Audio unit
F
Removal and Installation INFOID:0000000004235122

REMOVAL G
1. Remove cluster lid C and cluster lid D. Refer to IP-12, "Exploded View".
2. Remove audio unit mounting screws.
H
3. Pull out audio unit, remove harness clip, and then disconnect antenna feeder and harness connectors.
4. Remove audio unit and bracket as a unit.
5. Remove brackets from audio unit. I
INSTALLATION
Install in the reverse order of removal.
J

AV

Revision: 2008 August AV-29 2009 Rogue

 TWEETER
< ON-VEHICLE REPAIR > [BASE AUDIO]
TWEETER
Exploded View INFOID:0000000004235123

JSNIA0711ZZ

1. Tweeter

Removal and Installation INFOID:0000000004235124

REMOVAL
1. Remove instrument panel. Refer to IP-13, "Removal and Installation".
2. Remove tweeter from instrument panel.
INSTALLATION
Installation is the reverse order of removal.

Revision: 2008 August AV-30 2009 Rogue

 FRONT SPEAKER
< ON-VEHICLE REPAIR > [BASE AUDIO]
FRONT SPEAKER
A
Exploded View INFOID:0000000004235125

D
JSNIA0713ZZ

E
1. Front speaker
2. Bracket
F
Removal and Installation INFOID:0000000004235126

REMOVAL
G
1. Remove front door finisher. Refer to INT-11, "FRONT DOOR FINISHER : Removal and Installation".
2. Remove front door speaker from bracket.
INSTALLATION H
Install in the reverse order of removal.

AV

Revision: 2008 August AV-31 2009 Rogue

 REAR SPEAKER
< ON-VEHICLE REPAIR > [BASE AUDIO]
REAR SPEAKER
Exploded View INFOID:0000000004235127

JSNIA0714ZZ

1. Rear speaker

Removal and Installation INFOID:0000000004235128

REMOVAL
1. Remove rear door finisher. Refer to INT-14, "REAR DOOR FINISHER : Removal and Installation".
2. Remove rear speaker.
INSTALLATION
Installation is the reverse order of removal.

Revision: 2008 August AV-32 2009 Rogue

 STEERING SWITCH
< ON-VEHICLE REPAIR > [BASE AUDIO]
STEERING SWITCH
A
Exploded View INFOID:0000000004235129

Refer to SR-5, "Exploded View". B

Removal and Installation INFOID:0000000004235130

REMOVAL C
Refer to SR-5, "Removal and Installation".
INSTALLATION
D
Installation is the reverse order of removal.

AV

Revision: 2008 August AV-33 2009 Rogue

 RADIO ANTENNA
< ON-VEHICLE REPAIR > [BASE AUDIO]
RADIO ANTENNA
Exploded View INFOID:0000000004235131

JSNIA0721ZZ

1. Antenna rod 2. Antenna base

Removal and Installation INFOID:0000000004235132

REMOVAL
1. Remove headlining assembly. Refer to INT-23, "NORMAL ROOF : Removal and Installation" (normal roof
models) or INT-26, "SUNROOF : Removal and Installation" (sunroof models).
2. Remove nuts, and then remove radio antenna.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Be careful about tightening torque. Antenna sensitivity becomes poor, and when it is excessive, roof
panel may be deformed, when roof antenna mounting nut tightening torque is loose.

Revision: 2008 August AV-34 2009 Rogue

 ANTENNA FEEDER
< ON-VEHICLE REPAIR > [BASE AUDIO]
ANTENNA FEEDER
A
Location of Antenna INFOID:0000000004235133

AV

P
JSNIA0726GB

Revision: 2008 August AV-35 2009 Rogue

 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [BOSE AUDIO]

BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000004235134

OVERALL SEQUENCE

JSNIA0669GB

Reference 1 ··· Refer to AV-144, "Symptom Table".

DETAILED FLOW
1.CHECK SYMPTOM
Check the malfunction symptoms by performing the following items.
• Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred).
• Check the symptom.

>> GO TO 2.
2.PERFORM DIAGNOSIS BY SYMPTOM
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to AV-144, "Symptom
Table".

>> GO TO 3.
3.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace the malfunctioning parts.

>> GO TO 4.

Revision: 2008 August AV-36 2009 Rogue

 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION > [BOSE AUDIO]

4.FINAL CHECK A
Perform the operation to check that the malfunction symptom is solved or any other symptoms are present.
Is there any symptom?
YES >> GO TO 2. B
NO >> INSPECTION END

AV

Revision: 2008 August AV-37 2009 Rogue

 AUDIO SYSTEM
< FUNCTION DIAGNOSIS > [BOSE AUDIO]

FUNCTION DIAGNOSIS
AUDIO SYSTEM
System Diagram INFOID:0000000004235135

JSNIA0734GB

System Description INFOID:0000000004235136

AUDIO SYSTEM
Audio functions

AM/FM radio
6CD
• Radio signal are received by radio antenna, next it is amplified by antenna amp., and finally it is input to
audio unit. (Antenna amp. is built into radio antenna.)
• Audio unit outputs sound signal to BOSE amp. and BOSE amp. outputs to each speaker.
SATELLITE RADIO SYSTEM
• Radio signal are supplied to satellite radio tuner from the satellite antenna.
• The satellite radio tuner then sends sound signal to the audio unit.
• Audio unit outputs sound signal to BOSE amp. and BOSE amp. outputs to each speaker.
SPEED SENSITIVE VOLUME
• Volume level of this system gone up and down automatically in proportion to the vehicle speed.
• The control level can be selected by the customer.

Revision: 2008 August AV-38 2009 Rogue

 AUDIO SYSTEM
< FUNCTION DIAGNOSIS > [BOSE AUDIO]
Component Parts Location INFOID:0000000004235137

I
JSNIA0724ZZ

1. Center speaker 2. Tweeter LH 3. Front speaker LH

J
4. Rear speaker LH 5. Satellite radio tuner 6. Woofer
7. TEL adapter unit 8. TEL antenna 9. BOSE amp.
10. Radio & satellite radio antenna 11. Rear speaker RH 12. Front speaker RH
K
13. Tweeter RH 14. Audio unit 15. Microphone
16. Steering switch
A. Luggage side LH B. Luggage side RH C. Luggage side RH L
Component Description INFOID:0000000004235138

M
Part name Description
Audio unit Controls audio system and satellite radio system functions.
AV
• Receives power (amp. ON) and sound signals from audio unit, and outputs
BOSE amp. sound signals to each speaker.
• Woofer amp. ON signal is output to woofer.
• Each audio operation can be operated. O
• Steering switch signal (operation signal) is output to audio unit. (without
Steering switch hands-free phone system)
• Steering switch signal (operation signal) is output to audio unit through TEL
adapter unit. (with hands-free phone system) P
• Outputs sound signal from BOSE amp.
Front speaker
• Outputs high, mid and low range sounds.
• Outputs sound signal from BOSE amp.
Tweeter
• Outputs high range sounds.
• Outputs sound signal from BOSE amp.
Center speaker
• Outputs mid and high range sounds.

Revision: 2008 August AV-39 2009 Rogue

 AUDIO SYSTEM
< FUNCTION DIAGNOSIS > [BOSE AUDIO]
Part name Description
• Outputs sound signal from BOSE amp.
Rear speaker
• Outputs high, mid and low range sounds.
• Woofer amp. ON signal is input from BOSE amp.
Woofer • Outputs sound signal from BOSE amp.
• Outputs low range sounds.
Radio antenna
• Radio signal received by radio antenna is amplified and sent to audio unit.
Radio & satellite radio antenna • Power (antenna amp. ON signal) is supplied from audio unit.
Satellite radio antenna
• Sound signal (satellite radio) is received and output to audio unit.
• Receives radio signals from satellite antenna.
Satellite radio tuner
• Sends sound signals to audio unit.

Revision: 2008 August AV-40 2009 Rogue

 HANDS-FREE PHONE SYSTEM
< FUNCTION DIAGNOSIS > [BOSE AUDIO]
HANDS-FREE PHONE SYSTEM
A
System Diagram INFOID:0000000004235139

JSNIA0734GB
I

System Description INFOID:0000000004235140

J
• The connection between portable telephone and TEL adapter unit is performed with Bluetooth® communica-
tion.
• The voice guidance signal is input from the TEL adapter unit to the audio unit and output via BOSE amp. to
the front speaker when operating the telephone. K
• TEL adapter unit has the on board self-diagnosis function. Refer to AV-47, "Diagnosis Description".
WHEN RECEIVING A CALL
L
Telephone voice signal received with the portable telephone is input from TEL antenna via TEL adapter unit to
audio unit with Bluetooth communication and output via BOSE amp. to the front speaker. The operation is per-
formed with the steering switch or voice recognition function.
M
WHEN A CALL IS ORIGINATED
Speech sound (telephone voice signal) is input from the microphone to the TEL adapter unit. It is input from
the TEL antenna via Bluetooth communication to the portable telephone. It is transmitted to the phone on the
other side. The operation is performed with the steering switch or voice recognition function. AV

Revision: 2008 August AV-41 2009 Rogue

 HANDS-FREE PHONE SYSTEM
< FUNCTION DIAGNOSIS > [BOSE AUDIO]
Component Parts Location INFOID:0000000004235141

JSNIA0724ZZ

1. Center speaker 2. Tweeter LH 3. Front speaker LH

4. Rear speaker LH 5. Satellite radio tuner 6. Woofer
7. TEL adapter unit 8. TEL antenna 9. BOSE amp.
10. Radio & satellite radio antenna 11. Rear speaker RH 12. Front speaker RH
13. Tweeter RH 14. Audio unit 15. Microphone
16. Steering switch
A. Luggage side LH B. Luggage side RH C. Luggage side RH

Component Description INFOID:0000000004235142

Part name Description

• Receives telephone voice signal from TEL adapter unit.
• Sends telephone voice and voice guidance signals to BOSE amp.
Audio unit
• Audio unit and TEL adapter unit exchange data by AV communication, and
control audio unit display.
Inputs power (amp. ON) and sound signal from audio unit, and outputs sound sig-
BOSE amp.
nal to each speaker.
Front door speaker
Tweeter Receives telephone voice and voice guidance signals from BOSE amp.
Center speaker
• The hands free phone system can be operated.
Steering switch • Steering switch signal (operation signal) is output to audio unit through TEL
adapter unit.
• Uses when operating the hands-free phone.
Microphone • Outputs microphone signal (telephone voice signal) to the TEL adapter unit.
• The power (microphone power supply) is supplied from the TEL adapter unit.

Revision: 2008 August AV-42 2009 Rogue

 HANDS-FREE PHONE SYSTEM
< FUNCTION DIAGNOSIS > [BOSE AUDIO]
Part name Description
A
• Receives the steering switch signal (operation signal) from the steering switch.
• Inputs the telephone voice signal from TEL antenna during reception and out-
TEL adapter unit puts into the audio unit.
• Inputs the telephone voice signal from microphone during speech recognition B
and outputs it to the TEL antenna.

TEL antenna Connects with the portable telephone via Bluetooth® communication and com-
municates the telephone voice signal. C

AV

Revision: 2008 August AV-43 2009 Rogue

 DIAGNOSIS SYSTEM (AUDIO UNIT)
< FUNCTION DIAGNOSIS > [BOSE AUDIO]
DIAGNOSIS SYSTEM (AUDIO UNIT)
Diagnosis Description INFOID:0000000004235143

Self-diagnosis mode can check the following items.

• Audio unit hardware/software versions
• Continuity of each speaker channel
• Continuity of each audio unit switch
OPERATION PROCEDURE
1. Turn ignition switch to the ON position.
2. Turn the audio unit off.
3. While pressing the “AUDIO” button, turn the volume control dial
clockwise or counterclockwise 30 clicks or more. When the self-
diagnosis mode is started, a short beep will be heard.

AWNIA0026ZZ

4. Initially, all display segments will be illuminated.

ALNIA0019ZZ

Version Check
1. Press the “AUDIO” switch to enter version diagnostics. “Soft-
ware” (audio software version) is displayed.

ALNIA0020ZZ

Revision: 2008 August AV-44 2009 Rogue

 DIAGNOSIS SYSTEM (AUDIO UNIT)
< FUNCTION DIAGNOSIS > [BOSE AUDIO]
2. Press the “AUDIO” switch again to display the “Hardware”
(audio hardware version). A

ALNIA0021ZZ

D
3. Press the “AUDIO” switch again to display the “CD Mech” (CD
mechanism version).
E

G
ALNIA0022ZZ

4. Press the “AUDIO” switch again to display the “SDARS” (satel- H

lite radio version).

K
ALNIA0023ZZ

Channel Check Diagnostics

L
When all segments are illuminated, press the “TUNE” up switch to
enter channel check diagnostics. The self-diagnostic function will
then send a tone to each channel (FL, RL, RR, FR) for 1 second.
M

AV

O
ALNIA0024ZZ

Button Check Diagnostics

P

Revision: 2008 August AV-45 2009 Rogue

 DIAGNOSIS SYSTEM (AUDIO UNIT)
< FUNCTION DIAGNOSIS > [BOSE AUDIO]
When all segments are illuminated, press the “TUNE” down switch to
enter button check diagnostics. When each audio unit switch is
pressed, a tone will sound and the switch name will be displayed.

ALNIA0025ZZ

Revision: 2008 August AV-46 2009 Rogue

 DIAGNOSIS SYSTEM (TEL ADAPTER UNIT)
< FUNCTION DIAGNOSIS > [BOSE AUDIO]
DIAGNOSIS SYSTEM (TEL ADAPTER UNIT)
A
Diagnosis Description INFOID:0000000004235144

HANDS FREE PHONE SYSTEM ON BOARD DIAGNOSIS B

During on board diagnosis the diagnosis function of TEL adapter unit starts with the operation of the steering
switch and performs the diagnosis when ignition switch ACC.
ON BOARD DIAGNOSIS ITEM C
The on board diagnosis has 3 modes: the self-diagnosis mode that performs the trouble diagnosis, the
speaker adaptation data deleting mode and the hands free phone system initialization mode.
CAUTION: D
• Perform the diagnosis with the vehicle stopped.
• Perform STEP2 if necessary.
E
STEP MODE Description
The self-diagnosis mode performs the microphone test and
the diagnosis of TEL adapter unit, TEL antenna and steering
STEP 1 Self-diagnosis F
unit, and then reads out the results with the sound and indi-
cates them on the audio screen.
Hands free phone system initialization mode can perform
Hands free phone system initialization
the initialization of hands free phone system. G
STEP 2
The speaker adaptation data deleting mode can delete the
Speaker adaptation data deleting
speaker adaptation data.
H
SELF-DIAGNOSIS RESULTS
Self-diagnosis mode reads out the self-diagnosis results and indicates DTC on the audio screen.
NOTE:
• Error count is read out simultaneously when reading out the DTC name. I
• The errors are read out continuously when some errors occur at the same time. The DTC displays are com-
bined and displayed. For example, DTC 01100 is displayed when DTC 01000 and DTC 00100 are indicated
at the same time. J
Self-diagnosis results
DTC
Failure massage Possible causes
(Audio screen)
K
DTC 10000 Internal failure TEL adapter unit
DTC 01000 Bluetooth antenna open
TEL antenna
DTC 00100 Bluetooth antenna shorted L
DTC 00010 Button ladder A is stuck
Steering switch
DTC 00001 Button ladder B is stuck
M
DTC 00000 There are no failure records to report —

The Details of Error Count

The error count guides “0” when the error occurs. The next time it counts up “1” if it is normal with the ignition AV
switch ON. It continues the count up unless the initialization of hands free phone system is performed.

Revision: 2008 August AV-47 2009 Rogue

 DIAGNOSIS SYSTEM (TEL ADAPTER UNIT)
< FUNCTION DIAGNOSIS > [BOSE AUDIO]
FLOW CHART OF TROUBLE DIAGNOSIS

JSNIA0169GB

Revision: 2008 August AV-48 2009 Rogue

 POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]

COMPONENT DIAGNOSIS A
POWER SUPPLY AND GROUND CIRCUIT
AUDIO UNIT
B
AUDIO UNIT : Diagnosis Procedure INFOID:0000000004235145

1.CHECK FUSE C
Check that the following fuses of the audio unit are not blown.

D
Power source Fuse No.
Battery 35
Ignition switch ACC or ON 20 E
Is inspection result OK?
YES >> GO TO 2.
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. F
2.CHECK AUDIO UNIT POWER SUPPLY CIRCUIT
Check voltage between the audio unit and ground.
G
Signal name Connector No. Terminal No. Ignition switch position Voltage
Battery power supply M46 19 OFF Battery voltage
H
ACC power supply M46 7 ACC Battery voltage
Is inspection result OK?
YES >> INSPECTION END I
NO >> Check harness between audio unit and fuse.
BOSE AMP.
J
BOSE AMP. : Diagnosis Procedure INFOID:0000000004235146

1.CHECK FUSE K
Check that the following fuses of the BOSE amp. are not blown.

Power source Fuse No. L

Battery 13
Is inspection result OK?
M
YES >> GO TO 2.
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT AV
Check voltage between BOSE speaker amp harness connector and ground.

Signal name Connector No. Terminal No. Ignition switch position Voltage O
Battery power supply B64 11 OFF Battery voltage
Is inspection result OK?
P
YES >> GO TO 3.
NO >> Check harness between BOSE amp. and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BOSE amp. connector.
3. Check continuity between BOSE amp. harness connector and ground.

Revision: 2008 August AV-49 2009 Rogue

 POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]

Signal name Connector No. Terminal No. Ignition switch position Continuity
Ground B64 12 OFF Continuity should exist.
Is inspection result OK?
YES >> INSPECTION END
NO >> Repair harness or connector.
SATELLITE RADIO TUNER
SATELLITE RADIO TUNER : Diagnosis Procedure INFOID:0000000004235147

1.CHECK FUSES
Check that the following fuses of the satellite radio tuner are not blown.

Power source Fuse No.

Battery 35
Ignition switch ACC or ON 20
Is inspection result OK?
YES >> GO TO 2.
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between the satellite radio tuner and ground.

Signal name Connector No. Terminal No. Ignition switch position Voltage
Battery power supply B19 12 OFF Battery voltage
ACC power supply B19 16 ACC Battery voltage
Is inspection result OK?
YES >> INSPECTION END
NO >> Check harness between satellite radio tuner and fuse.
TEL ADAPTER UNIT
TEL ADAPTER UNIT : Diagnosis Procedure INFOID:0000000004235148

1.CHECK FUSES
Check that the following fuses of the TEL adapter unit are not blown.

Power source Fuse No.

Battery 35
Ignition switch ACC or ON 20
Ignition switch ON or START 1
Is inspection result OK?
YES >> GO TO 2.
NO >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between TEL adapter unit harness connector and ground.

Signal name Connector No. Terminal No. Ignition switch position Voltage
Battery power supply B6 1 OFF Battery voltage
ACC power supply B6 2 ACC Battery voltage
Ignition signal B6 3 ON Battery voltage
Is inspection result OK?

Revision: 2008 August AV-50 2009 Rogue

 POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
YES >> GO TO 3.
NO >> Check harness between TEL adapter unit and fuse. A
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
B
2. Disconnect TEL adapter unit connector.
3. Check continuity between TEL adapter unit harness connector and ground.

Signal name Connector No. Terminal No. Ignition switch position Continuity C
4 OFF Continuity should exist.
21 OFF Continuity should exist.
D
Ground B6 22 OFF Continuity should exist.
23 OFF Continuity should exist.
24 OFF Continuity should exist. E
Is inspection result OK?
YES >> INSPECTION END
NO >> Repair harness or connector. F

AV

Revision: 2008 August AV-51 2009 Rogue

 STEERING SWITCH SIGNAL A CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
STEERING SWITCH SIGNAL A CIRCUIT
Description INFOID:0000000004678870

Transmits the steering switch signal to audio unit.

Diagnosis Procedure INFOID:0000000004678871

1.CHECK STEERING SWITCH SIGNAL A CIRCUIT

1. Turn ignition switch OFF.
2. Disconnect audio unit connector and spiral cable connector.
3. Check continuity between audio unit harness connector and spiral cable harness connector.

Audio unit Spiral cable

Continuity
Connector Terminal Connector Terminal
M46 6 M33 24 Existed
4. Check continuity between audio unit harness connector.

Audio unit
Continuity
Connector Terminal Ground
M46 6 Not existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK SPIRAL CABLE
Check spiral cable.
Is inspection result OK?
YES >> GO TO 3.
NO >> Replace spiral cable.
3.CHECK AUDIO UNIT VOLTAGE
1. Connect audio unit connector and spiral cable connector.
2. Turn ignition switch ON.
3. Check voltage between audio unit harness connector.

(+) (−)
Voltage
Audio unit Audio unit
(Approx.)
Connector Terminal Connector Terminal
M46 6 M46 15 3.3 V
Is inspection result OK?
YES >> GO TO 4.
NO >> Replace audio unit.
4.CHECK STEERING SWITCH
1. Turn ignition switch ON.
2. Check steering switch. Refer to AV-53, "Component Inspection".
Is inspection result OK?
YES >> INSPECTION END
NO >> Replace steering switch.

Revision: 2008 August AV-52 2009 Rogue

 STEERING SWITCH SIGNAL A CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
Component Inspection INFOID:0000000004678872

A
Measure the resistance between the steering switch connector.
Standard

Steering switch
B
Resistance
Condition
Terminal Terminal Ω

VOL UP switch ON 645 – 659

C
16 SEEK UP switch ON 163 – 167
SOURCE switch ON 0
17
VOL DOWN switch ON 645 – 659 D
20 SEEK DOWN switch ON 163 – 167
POWER switch ON 0 JSNIA0673GB
E

AV

Revision: 2008 August AV-53 2009 Rogue

 STEERING SWITCH SIGNAL B CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
STEERING SWITCH SIGNAL B CIRCUIT
Description INFOID:0000000004678873

Transmits the steering switch signal to audio unit.

Diagnosis Procedure INFOID:0000000004678874

1.CHECK STEERING SWITCH SIGNAL B CIRCUIT

1. Turn ignition switch OFF.
2. Disconnect audio unit connector and spiral cable connector.
3. Check continuity between audio unit harness connector and spiral cable harness connector.

Audio unit Spiral cable

Continuity
Connector Terminal Connector Terminal
M46 16 M33 32 Existed
4. Check continuity between audio unit harness connector.

Audio unit
Continuity
Connector Terminal Ground
M46 16 Not existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK SPIRAL CABLE
Check spiral cable.
Is inspection result OK?
YES >> GO TO 3.
NO >> Replace spiral cable.
3.CHECK AUDIO UNIT VOLTAGE
1. Connect audio unit connector and spiral cable connector.
2. Turn ignition switch ON.
3. Check voltage between audio unit harness connector.

(+) (−)
Voltage
Audio unit Audio unit
(Approx.)
Connector Terminal Connector Terminal
M46 16 M46 15 3.3 V
Is inspection result OK?
YES >> GO TO 4.
NO >> Replace audio unit.
4.CHECK STEERING SWITCH
1. Turn ignition switch ON.
2. Check steering switch. Refer to AV-55, "Component Inspection".
Is inspection result OK?
YES >> INSPECTION END
NO >> Replace steering switch.

Revision: 2008 August AV-54 2009 Rogue

 STEERING SWITCH SIGNAL B CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
Component Inspection INFOID:0000000004678875

A
Measure the resistance between the steering switch connector.
Standard

Steering switch
B
Resistance
Condition
Terminal Terminal Ω

VOL UP switch ON 645 – 659

C
16 SEEK UP switch ON 163 – 167
SOURCE switch ON 0
17
VOL DOWN switch ON 645 – 659 D
20 SEEK DOWN switch ON 163 – 167
POWER switch ON 0 JSNIA0673GB
E

AV

Revision: 2008 August AV-55 2009 Rogue

 STEERING SWITCH SIGNAL GND CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
STEERING SWITCH SIGNAL GND CIRCUIT
Description INFOID:0000000004678876

Transmits the steering switch signal to audio unit.

Diagnosis Procedure INFOID:0000000004678877

1.CHECK STEERING SWITCH SIGNAL GND CIRCUIT

1. Turn ignition switch OFF.
2. Disconnect audio unit connector and spiral cable connector.
3. Check continuity between audio unit harness connector and spiral cable harness connector.

Audio unit Spiral cable

Continuity
Connector Terminal Connector Terminal
M46 15 M33 31 Existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK SPIRAL CABLE
Check spiral cable.
Is inspection result OK?
YES >> GO TO 3.
NO >> Replace spiral cable.
3.CHECK GROUND CIRCUIT
1. Connect audio unit connector.
2. Check continuity between audio unit harness connector terminals 15 and ground.

Audio unit
Continuity
Connector Terminal Ground
M46 15 Existed
Is inspection result OK?
YES >> GO TO 4.
NO >> Replace audio unit.
4.CHECK STEERING SWITCH
1. Turn ignition switch ON.
2. Check steering switch. Refer to AV-56, "Component Inspection".
Is inspection result OK?
YES >> INSPECTION END
NO >> Replace steering switch.
Component Inspection INFOID:0000000004678878

Measure the resistance between the steering switch connector.

Revision: 2008 August AV-56 2009 Rogue

 STEERING SWITCH SIGNAL GND CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
Standard

Steering switch Resistance

A
Condition
Terminal Terminal Ω

VOL UP switch ON 645 – 659

B
16 SEEK UP switch ON 163 – 167
SOURCE switch ON 0
17
VOL DOWN switch ON 645 – 659 C
20 SEEK DOWN switch ON 163 – 167
POWER switch ON 0 JSNIA0673GB

AV

Revision: 2008 August AV-57 2009 Rogue

 STEERING SWITCH SIGNAL A CIRCUIT (STEERING SWITCH TO TEL ADAPT-
ER UNIT)
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
STEERING SWITCH SIGNAL A CIRCUIT (STEERING SWITCH TO TEL
ADAPTER UNIT)
Description INFOID:0000000004235149

• Transmits the steering switch signal to TEL adapter unit.

• Transmits the steering switch signal to audio unit through TEL adapter unit.
Diagnosis Procedure INFOID:0000000004235150

1.CHECK STEERING SWITCH SIGNAL A CIRCUIT (STEERING SWITCH TO TEL ADAPTER UNIT)
1. Turn ignition switch OFF.
2. Disconnect TEL adapter unit connector and spiral cable connector.
3. Check continuity between TEL adapter unit harness connector and spiral cable harness connector.

TEL adapter unit Spiral cable

Continuity
Connector Terminal Connector Terminal
B6 12 M33 24 Existed
4. Check continuity between audio unit harness connector and ground.

TEL adapter unit

Continuity
Connector Terminal Ground
B6 12 Not existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK SPIRAL CABLE
Check spiral cable.
Is inspection result OK?
YES >> GO TO 3.
NO >> Replace spiral cable.
3.CHECK TEL ADAPTER UNIT VOLTAGE
1. Connect TEL adapter unit connector and spiral cable connector.
2. Turn ignition switch ON.
3. Check voltage between TEL adapter unit harness connector.

(+) (−)
Voltage
TEL adapter unit TEL adapter unit
(Approx.)
Connector Terminal Connector Terminal
B6 12 B6 14 5.0 V
Is inspection result OK?
YES >> GO TO 4.
NO >> Replace TEL adapter unit.
4.CHECK STEERING SWITCH
1. Turn ignition switch OFF.
2. Check steering switch. Refer to AV-59, "Component Inspection".
Is inspection result OK?
YES >> INSPECTION END
NO >> Replace steering switch.

Revision: 2008 August AV-58 2009 Rogue

 STEERING SWITCH SIGNAL A CIRCUIT (STEERING SWITCH TO TEL ADAPT-
ER UNIT)
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
Component Inspection INFOID:0000000004235151

A
Measure the resistance between the steering switch connector.
Standard

Steering switch
B
Resistance
Condition
Terminal Terminal Ω

SOURCE switch ON 1000 – 1020

C
switch ON 327 – 333
16
VOL UP switch ON 109 – 111
D
17 VOL DOWN switch ON 0
SEEK DOWN switch ON 327 – 333
JSNIA0672GB
20 SEEK UP switch ON 109 – 111 E
switch ON 0

AV

Revision: 2008 August AV-59 2009 Rogue

 STEERING SWITCH SIGNAL B CIRCUIT (STEERING SWITCH TO TEL ADAPT-
ER UNIT)
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
STEERING SWITCH SIGNAL B CIRCUIT (STEERING SWITCH TO TEL
ADAPTER UNIT)
Description INFOID:0000000004235152

• Transmits the steering switch signal to TEL adapter unit.

• Transmits the steering switch signal to audio unit through TEL adapter unit.
Diagnosis Procedure INFOID:0000000004235153

1.CHECK STEERING SWITCH SIGNAL B CIRCUIT (STEERING SWITCH TO TEL ADAPTER UNIT)
1. Turn ignition switch OFF.
2. Disconnect TEL adapter unit connector and spiral cable connector.
3. Check continuity between TEL adapter unit harness connector and spiral cable harness connector.

TEL adapter unit Spiral cable

Continuity
Connector Terminal Connector Terminal
B6 13 M33 32 Existed
4. Check continuity between audio unit harness connector.

TEL adapter unit

Continuity
Connector Terminal Ground
B6 13 Not existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK SPIRAL CABLE
Check spiral cable.
Is inspection result OK?
YES >> GO TO 3.
NO >> Replace spiral cable.
3.CHECK TEL ADAPTER UNIT VOLTAGE
1. Connect TEL adapter unit connector and spiral cable connector.
2. Turn ignition switch ON.
3. Check voltage between TEL adapter unit harness connector.

(+) (−)
Voltage
TEL adapter unit TEL adapter unit
(Approx.)
Connector Terminal Connector Terminal
B6 13 B6 14 5.0 V
Is inspection result OK?
YES >> GO TO 4.
NO >> Replace TEL adapter unit.
4.CHECK STEERING SWITCH
1. Turn ignition switch OFF.
2. Check steering switch. Refer to AV-61, "Component Inspection".
Is inspection result OK?
YES >> INSPECTION END
NO >> Replace steering switch.

Revision: 2008 August AV-60 2009 Rogue

 STEERING SWITCH SIGNAL B CIRCUIT (STEERING SWITCH TO TEL ADAPT-
ER UNIT)
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
Component Inspection INFOID:0000000004235154

A
Measure the resistance between the steering switch connector.
Standard

Steering switch
B
Resistance
Condition
Terminal Terminal Ω

SOURCE switch ON 1000 – 1020

C
switch ON 327 – 333
16
VOL UP switch ON 109 – 111
D
17 VOL DOWN switch ON 0
SEEK DOWN switch ON 327 – 333
JSNIA0672GB
20 SEEK UP switch ON 109 – 111 E
switch ON 0

AV

Revision: 2008 August AV-61 2009 Rogue

 STEERING SWITCH SIGNAL GND CIRCUIT (STEERING SWITCH TO TEL
ADAPTER UNIT)
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
STEERING SWITCH SIGNAL GND CIRCUIT (STEERING SWITCH TO TEL
ADAPTER UNIT)
Description INFOID:0000000004235155

• Transmits the steering switch signal to TEL adapter unit.

• Transmits the steering switch signal to audio unit through TEL adapter unit.
Diagnosis Procedure INFOID:0000000004235156

1.CHECK STEERING SWITCH SIGNAL GND CIRCUIT (STEERING SWITCH TO TEL ADAPTER UNIT)
1. Turn ignition switch OFF.
2. Disconnect TEL adapter unit connector and spiral cable connector.
3. Check continuity between TEL adapter unit harness connector and spiral cable harness connector.

TEL adapter unit Spiral cable

Continuity
Connector Terminal Connector Terminal
B6 14 M33 31 Existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK SPIRAL CABLE
Check spiral cable.
Is inspection result OK?
YES >> GO TO 3.
NO >> Replace spiral cable.
3.CHECK GROUND CIRCUIT
1. Connect TEL adapter unit connector.
2. Check continuity between TEL adapter unit harness connector.

TEL adapter unit

Continuity
Connector Terminal Ground
B6 14 Existed
Is inspection result OK?
YES >> GO TO 4.
NO >> Replace TEL adapter unit.
4.CHECK STEERING SWITCH
1. Turn ignition switch OFF.
2. Check steering switch. Refer to AV-62, "Component Inspection".
Is inspection result OK?
YES >> INSPECTION END
NO >> Replace steering switch.
Component Inspection INFOID:0000000004235157

Measure the resistance between the steering switch connector.

Revision: 2008 August AV-62 2009 Rogue

 STEERING SWITCH SIGNAL GND CIRCUIT (STEERING SWITCH TO TEL
ADAPTER UNIT)
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
Standard

Steering switch Resistance

A
Condition
Terminal Terminal Ω

SOURCE switch ON 1000 – 1020

B
switch ON 327 – 333
16
VOL UP switch ON 109 – 111
17 VOL DOWN switch ON 0 C
SEEK DOWN switch ON 327 – 333
JSNIA0672GB
20 SEEK UP switch ON 109 – 111
D
switch ON 0

AV

Revision: 2008 August AV-63 2009 Rogue

 STEERING SWITCH SIGNAL A CIRCUIT (TEL ADAPTER UNIT TO AUDIO UNIT)
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
STEERING SWITCH SIGNAL A CIRCUIT (TEL ADAPTER UNIT TO AUDIO
UNIT)
Description INFOID:0000000004235158

• Transmits the steering switch signal to TEL adapter unit.

• Transmits the steering switch signal to audio unit through TEL adapter unit.
Diagnosis Procedure INFOID:0000000004235159

1.CHECK STEERING SWITCH SIGNAL A (TEL ADAPTER UNIT TO AUDIO UNIT) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect audio unit connector and TEL adapter unit connector.
3. Check continuity between audio unit harness connector and TEL adapter unit harness connector.

Audio unit TEL adapter unit

Continuity
Connector Terminal Connector Terminal
M46 6 B6 17 Existed
4. Check continuity between audio unit harness connector.

Audio unit
Continuity
Connector Terminal Ground
M46 6 Not existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK AUDIO UNIT VOLTAGE
1. Connect audio unit connector and TEL adapter unit connector.
2. Turn ignition switch ON.
3. Check voltage between audio unit harness connector.

(+) (−)
Voltage
Audio unit Audio unit
(Approx.)
Connector Terminal Connector Terminal
M46 6 M46 15 3.3 V
Is inspection result OK?
YES >> Replace TEL adapter unit.
NO >> Replace audio unit.

Revision: 2008 August AV-64 2009 Rogue

 STEERING SWITCH SIGNAL B CIRCUIT (TEL ADAPTER UNIT TO AUDIO UNIT)
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
STEERING SWITCH SIGNAL B CIRCUIT (TEL ADAPTER UNIT TO AUDIO
A
UNIT)
Description INFOID:0000000004235160
B
• Transmits the steering switch signal to TEL adapter unit.
• Transmits the steering switch signal to audio unit through TEL adapter unit.
C
Diagnosis Procedure INFOID:0000000004235161

D
1.CHECK STEERING SWITCH SIGNAL B (TEL ADAPTER UNIT TO AUDIO UNIT) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect audio unit connector and TEL adapter unit connector. E
3. Check continuity between audio unit harness connector and TEL adapter unit harness connector.

Audio unit TEL adapter unit F

Continuity
Connector Terminal Connector Terminal
M46 16 B6 18 Existed
G
4. Check continuity between audio unit harness connector terminal.

Audio unit H
Continuity
Connector Terminal Ground
M46 16 Not existed
Is inspection result OK? I
YES >> GO TO 2.
NO >> Repair harness or connector.
J
2.CHECK AUDIO UNIT VOLTAGE
1. Connect audio unit connector and TEL adapter unit connector.
2. Turn ignition switch ON. K
3. Check voltage between audio unit harness connector.

(+) (−) L
Voltage
Audio unit Audio unit
(Approx.)
Connector Terminal Connector Terminal
M46 16 M46 15 3.3 V M
Is inspection result OK?
YES >> Replace TEL adapter unit. AV
NO >> Replace audio unit.

Revision: 2008 August AV-65 2009 Rogue

 STEERING SWITCH SIGNAL GND CIRCUIT (TEL ADAPTER UNIT TO AUDIO
UNIT)
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
STEERING SWITCH SIGNAL GND CIRCUIT (TEL ADAPTER UNIT TO AU-
DIO UNIT)
Description INFOID:0000000004235162

• Transmits the steering switch signal to TEL adapter unit.

• Transmits the steering switch signal to audio unit through TEL adapter unit.
Diagnosis Procedure INFOID:0000000004235163

1.CHECK STEERING SWITCH SIGNAL GND (TEL ADAPTER UNIT TO AUDIO UNIT) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect audio unit connector and TEL adapter unit connector.
3. Check continuity between audio unit harness connector terminal 15 and TEL adapter unit harness con-
nector terminal 19.

Audio unit TEL adapter unit

Continuity
Connector Terminal Connector Terminal
M46 15 B6 19 Existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK GROUND CIRCUIT
1. Connect audio unit connector.
2. Check continuity between audio unit harness connector.

Audio unit
Continuity
Connector Terminal Ground
M46 15 Existed
Is inspection result OK?
YES >> Replace TEL adapter unit.
NO >> Replace audio unit.

Revision: 2008 August AV-66 2009 Rogue

 COMMUNICATION SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
COMMUNICATION SIGNAL CIRCUIT
A
Description INFOID:0000000004235164

Satellite radio tuner and audio unit are connected with a serial communication. They transmit the operation B
signal from audio unit to satellite radio tuner.
Diagnosis Procedure INFOID:0000000004235165

C
1.CHECK CONTINUITY COMMUNICATION SIGNAL (AUDIO−SAT) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect satellite radio tuner connector and audio unit connector. D
3. Check continuity between satellite radio tuner harness connector and audio unit harness connector.

Satellite radio tuner Audio unit E

Continuity
Connector Terminal Connector Terminal
9 39 Existed
B19 M48 F
10 40 Existed
4. Check continuity between satellite radio tuner harness connector and ground.
G
Satellite radio tuner
Continuity
Connector Terminal
Ground H
9
B19 Not existed
10
Is inspection result OK? I
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK AUDIO UNIT J
1. Connect audio unit connector.
2. Turn ignition switch ON.
3. Check voltage between audio unit harness connector and ground. K

Audio unit Voltage

(Approx.) L
Connector Terminal Ground
M48 39 4.0 V
Is inspection result OK? M
YES >> GO TO 3.
NO >> Replace audio unit.
3.CHECK SATELLITE RADIO TUNER AV
1. Turn ignition switch OFF.
2. Disconnect audio unit connector, and connect satellite radio tuner connector.
3. Turn ignition switch ON. O
4. Check voltage between satellite radio tuner harness connector and ground.

Satellite radio tuner Voltage P

Connector Terminal Ground (Approx)

B19 10 7.5 V
Is inspection result OK?
YES >> GO TO 4.
NO >> Replace satellite radio tuner.

Revision: 2008 August AV-67 2009 Rogue

 COMMUNICATION SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]

4.CHECK COMMUNICATION SIGNAL (SAT−AUDIO)

1. Turn ignition switch OFF.
2. Connect audio unit connector.
3. Turn ignition switch ON.
4. Check signal between satellite radio tuner harness connector and ground.

Satellite radio tuner

Condition Reference value
Connector Terminal

Ground
When satellite radio mode is
B19 9
selected.

PKIB5039J

Is inspection result OK?

YES >> GO TO 5.
NO >> Replace satellite radio tuner.
5.CHECK COMMUNICATION SIGNAL (AUDIO−SAT)
Check signal between audio unit harness connector and ground.

Audio unit
Condition Reference value
Connector Terminal

Ground
When satellite radio mode is
M48 40
selected.

SKIA9301J

Is inspection result OK?

YES >> INSPECTION END
NO >> Replace audio unit.

Revision: 2008 August AV-68 2009 Rogue

 REQUEST SIGNAL CIRCUIT (SAT TO AUDIO)
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
REQUEST SIGNAL CIRCUIT (SAT TO AUDIO)
A
Description INFOID:0000000004235166

Request signal transmits the signal to recognize the connection of satellite radio tuner from satellite radio B
tuner to audio unit.
Diagnosis Procedure INFOID:0000000004235167

C
1.CHECK CONTINUITY REQUEST SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect satellite radio tuner connector and audio unit connector. D
3. Check continuity between satellite radio tuner unit harness connector and audio unit harness connector.

Satellite radio tuner Audio unit E

Continuity
Connector Terminal Connector Terminal
B19 8 M48 38 Existed
F
4. Check continuity between satellite radio tuner harness connector and ground.

Satellite radio tuner G

Continuity
Connector Terminal Ground
B19 8 Not existed
H
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
I
2.CHECK AUDIO UNIT
1. Connect audio unit connector.
2. Turn ignition switch ON. J
3. Check voltage between audio unit harness connector and ground.

Audio unit Voltage K

Connector Terminal Ground (Approx.)

M48 38 4.0 V
L
Is inspection result OK?
YES >> GO TO 3.
NO >> Replace audio unit.
M
3.CHECK CONTINUITY REQUEST SIGNAL
1. Turn ignition switch OFF.
2. Connect satellite radio tuner connector. AV
3. Turn ignition switch ON.
4. Check signal between satellite radio tuner harness connector and ground.
O
Satellite radio tuner
Condition Reference value
Connector Terminal
P

Ground
When satellite radio mode is
B19 8
selected.

JSNIA0675ZZ

Revision: 2008 August AV-69 2009 Rogue

 REQUEST SIGNAL CIRCUIT (SAT TO AUDIO)
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
Is inspection result OK?
YES >> INSPECTION END
NO >> Replace satellite radio tuner.

Revision: 2008 August AV-70 2009 Rogue

 AMP. ON SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
AMP. ON SIGNAL CIRCUIT
A
Description INFOID:0000000004235168

When the audio system is turned on, a voltage signal is supplied from the audio unit to the BOSE amp. When B
this signal is received, the BOSE amp. will turn on.
Diagnosis Procedure INFOID:0000000004235169

C
1.CHECK CONTINUITY AMP. ON SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect audio unit connector and BOSE amp. connector. D
3. Check continuity between audio unit harness connector and BOSE amp. harness connector.

Audio unit BOSE amp. E

Continuity
Connector Terminal Connector Terminal
M46 1 B65 31 Existed
F
4. Check continuity between audio unit harness connector terminal 1 and ground.

Audio unit G
Continuity
Connector Terminal Ground
M46 1 Not existed
H
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
I
2.CHECK VOLTAGE AMP. ON SIGNAL
1. Connect audio unit connector.
2. Turn ignition switch ON. J
3. Check voltage between audio unit harness connector and ground.

Audio unit Voltage K

Connector Terminal Ground (Approx.)

M46 1 12.0 V
L
Is inspection result OK?
YES >> Replace BOSE amp.
NO >> Replace audio unit.
M

AV

Revision: 2008 August AV-71 2009 Rogue

 WOOFER AMP. ON SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
WOOFER AMP. ON SIGNAL CIRCUIT
Description INFOID:0000000004235170

When the audio system is turned on, a voltage signal is supplied from the BOSE amp. to the woofer. When
this signal is received, the woofer will turn on.
Diagnosis Procedure INFOID:0000000004235171

1.CHECK CONTINUITY WOOFER AMP. ON SIGNAL CIRCUIT

1. Turn ignition switch OFF.
2. Disconnect BOSE amp. connector and woofer connector.
3. Check continuity between BOSE amp. harness connector and woofer harness connector.

BOSE amp. Woofer

Continuity
Connector Terminal Connector Terminal
B65 25 B63 4 Existed
4. Check continuity between BOSE amp. harness connector and ground.

BOSE amp.
Continuity
Connector Terminal Ground
B65 25 Not existed
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK VOLTAGE AMP. ON SIGNAL
1. Connect BOSE amp. connector
2. Turn ignition switch ON.
3. Check voltage between BOSE amp. harness connector and ground.

BOSE amp. Voltage

Connector Terminal Ground (Approx.)

B65 25 12.0 V
Is inspection result OK?
YES >> Replace woofer.
NO >> Replace BOSE amp.

Revision: 2008 August AV-72 2009 Rogue

 MICROPHONE SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
MICROPHONE SIGNAL CIRCUIT
A
Description INFOID:0000000004235172

Supply power from TEL adapter unit to microphone. The microphone transmits the sound voice to the TEL B
adapter unit.
Diagnosis Procedure INFOID:0000000004235173

C
1.CHECK CONTINUITY BETWEEN TEL ADAPTER UNIT AND MICROPHONE CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect TEL adapter unit connector and microphone connector. D
3. Check continuity between TEL adapter unit harness connector and microphone harness connector.

TEL adapter unit Microphone E

Continuity
Connector Terminal Connector Terminal
7 1
F
B6 8 R3 2 Existed
29 4
4. Check continuity between TEL adapter unit harness connector and ground. G

TEL adapter unit

Continuity H
Connector Terminal
Ground
7
B6 Not existed
29 I
Is inspection result OK?
YES >> GO TO 2.
NO >> Repair harness or connector. J
2.CHECK MICROPHONE POWER SUPPLY
1. Connect TEL adapter unit connector.
K
2. Turn ignition switch ON.
3. Check voltage between TEL adapter unit harness connector and ground.

L
TEL adapter unit Voltage
Connector Terminal Ground (Approx.)

B6 29 5.0 V M
Is inspection result OK?
YES >> GO TO 3.
NO >> Replace TEL adapter unit. AV
3.CHECK MICROPHONE SIGNAL
1. Turn ignition switch OFF.
O
2. Connect microphone connector.
3. Turn ignition switch ON.
4. Check signal between TEL adapter unit harness connector terminals 7 and 8.
P

Revision: 2008 August AV-73 2009 Rogue

 MICROPHONE SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]

TEL adapter unit TEL adapter unit

Condition Reference value
Connector Terminal Connector Terminal

B6 7 B6 8 Give a voice.

SKIB3609E

Is inspection result OK?

YES >> INSPECTION END
NO >> Replace microphone.

Revision: 2008 August AV-74 2009 Rogue

 TELEPHONE ON SIGNAL CIRCUIT
< COMPONENT DIAGNOSIS > [BOSE AUDIO]
TELEPHONE ON SIGNAL CIRCUIT
A
Description INFOID:0000000004235174

When telephone is being used. TEL adapter unit transmits telephone ON signal to audio unit. B
Diagnosis Procedure INFOID:0000000004235175

1.CHECK CONTINUITY TELEPHONE ON SIGNAL CIRCUIT C

1. Turn ignition switch OFF.
2. Disconnect TEL adapter unit connector and audio unit connector.
3. Check continuity between TEL adapter unit harness connector and audio unit harness connector. D

TEL adapter unit Audio unit

Continuity E
Connector Terminal Connector Terminal
B6 11 M47 28 Existed
4. Check continuity between TEL adapter unit harness connector and ground. F

TEL adapter unit

Continuity
Connector Terminal Ground G
B6 11 Not existed
Is inspection result OK? H
YES >> GO TO 2.
NO >> Repair harness or connector.
2.CHECK TELEPHONE ON SIGNAL I
1. Connect audio unit connector.
2. Turn ignition switch ON.
3. Check voltage between audio unit harness connector and ground. J

Audio unit Voltage

Condition
Connector Terminal (Approx.) K

Ground While using hands-free

0V
phone system
M47 28 L
While not using hands-free
5.0 V
phone system
Is inspection result OK?
M
YES >> INSPECTION END
NO >> Replace audio unit.

AV

Revision: 2008 August AV-75 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

ECU DIAGNOSIS
AUDIO UNIT
Reference Value INFOID:0000000004235176

TERMINAL LAYOUT

JSNIA0759ZZ

PHYSICAL VALUES

Terminal
Description
(Wire color) Reference value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
1
Ground BOSE amp. ON signal Output switch — 12.0 V
(BR)
ON

Ignition
2 3
Sound signal front LH Output switch Sound signal output
(R) (G)
ON

SKIB3609E

Ignition
4 5
Sound signal rear LH Output switch Sound signal output
(V) (LG)
ON

SKIB3609E

Keep pressing SOURCE

0V
switch
6 Ignition Keep pressing SEEK UP
15 1.1 V
(W) Steering switch signal A Input switch switch
(GR)
(BR)* ON Keep pressing VOL UP
2.2 V
switch
Except for above 3.3 V
Ignition
7
Ground ACC power supply Input switch — Battery voltage
(SB)
ACC
Ignition Lighting switch is ON 0V
9 8
Illumination signal Input switch
(R) (Y) Lighting switch is OFF 12.0 V
OFF
10 — Shield — — — —

Revision: 2008 August AV-76 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]
Terminal
Description
(Wire color) Reference value A
Condition
Input/ (Approx.)
+ – Signal name
Output
B

Ignition
11 12 C
Sound signal front RH Output switch Sound signal output
(O) (W)
ON

SKIB3609E D

E
Ignition
13 14
Sound signal rear RH Output switch Sound signal output
(L) (P)
ON
F
SKIB3609E

Ignition
15 Steering switch signal G
Ground — switch — 0V
(GR) ground
ON
Keep pressing POWER
0V H
switch*
Ignition Keep pressing SEEK
16 15 1.1 V
Steering switch signal B Input switch DOWN switch
(O) (GR)
ON Keep pressing VOL DOWN
I
2.2 V
switch
Except for above 3.3 V
J
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit). K
Ignition
18 Vehicle speed signal When vehicle speed is ap-
Ground Input switch
(L) (8-pulse) prox. 40 km/h (25MPH)
ON
L

JSNIA0012GB M
Ignition
19
Ground Battery power supply Input switch — Battery voltage
(Y)
OFF
AV
20 — Shield — — — —
21 AV communication signal Input/
— — — —
(L) (H) Output O
22 AV communication signal Input/
— — — —
(P) (L) Output
23 — Shield — — — — P
25 — Shield — — — —

Revision: 2008 August AV-77 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]
Terminal
Description
(Wire color) Reference value
Condition
Input/ (Approx.)
+ – Signal name
Output

Sound signal Ignition

26 27
(Telephone voice, tele- Input switch Give a voice
(BR) (Y)
phone guidance) ON

SKIB3609E

While using hands-free

Ignition 0V
28 phone system
Ground Telephone ON signal Input switch
(V) While not using hands-free
ON 5.0 V
phone system

Ignition
32 31 Satellite radio sound signal When satellite radio mode
Input switch
(L) (R) LH is selected
ON

SKIB3609E

Ignition
34 33 Satellite radio sound signal When satellite radio mode
Input switch
(W) (G) RH is selected
ON

SKIB3609E

35 — Shield — — — —
36 — Shield — — — —

Ignition
38 Request signal When satellite radio mode
Ground Input switch
(Y) (SAT TO AUDIO) is selected
ON

JSNIA0675ZZ

Ignition
39 Communication signal When satellite radio mode
Ground Input switch
(B) (SAT-AUDIO) is selected
ON

PKIB5039J

Ignition
40 Communication signal When satellite radio mode
Ground Output switch
(L) (AUDIO-SAT) is selected
ON

SKIA9301J

Revision: 2008 August AV-78 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]
Terminal
Description
(Wire color) Reference value A
Condition
Input/ (Approx.)
+ – Signal name
Output
51 — Antenna signal Input — — — B
Ignition
52 Ground Antenna amp. ON signal Output switch — 12.0 V
ON C
* : Without telephone system

AV

Revision: 2008 August AV-79 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]
Wiring Diagram - BOSE AUDIO - INFOID:0000000004235177

JCNWM1642GB

Revision: 2008 August AV-80 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1643GB

Revision: 2008 August AV-81 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1644GB

Revision: 2008 August AV-82 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1645GB

Revision: 2008 August AV-83 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1646GB

Revision: 2008 August AV-84 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1647GB

Revision: 2008 August AV-85 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1648GB

Revision: 2008 August AV-86 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1649GB

Revision: 2008 August AV-87 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1650GB

Revision: 2008 August AV-88 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1651GB

Revision: 2008 August AV-89 2009 Rogue

 AUDIO UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1652GB

Revision: 2008 August AV-90 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]
BOSE AMP.
A
Reference Value INFOID:0000000004235178

TERMINAL LAYOUT B

JSNIA0760ZZ E
PHYSICAL VALUES

Terminal F
Description
(Wire color) Reference value
Condition
Input/ (Approx.)
+ – Signal name
Output G

H
Ignition
1 10 Sound signal rear speaker
Output switch Sound signal output
(L) (R) LH
ON
I
SKIB3609E

Ignition
2 3 Sound signal rear speaker
Output switch Sound signal output
(GR) (Y) RH K
ON

SKIB3609E
L

Ignition M
4 5 Sound signal front speaker
Output switch Sound signal output
(B) (P) LH
ON

AV
SKIB3609E

O
Ignition
6 7
Sound signal tweeter LH Output switch Sound signal output
(BR) (GR)
ON
P

SKIB3609E

Revision: 2008 August AV-91 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]
Terminal
Description
(Wire color) Reference value
Condition
Input/ (Approx.)
+ – Signal name
Output

Ignition
8 13 Sound signal front speaker
Output switch Sound signal output
(G) (R) RH
ON

SKIB3609E

Ignition
9 14
Sound signal woofer Output switch Sound signal output
(Y) (BR)
ON

SKIB3609E

Ignition
11
Ground Battery power supply Input switch — Battery voltage
(W)
OFF
Ignition
12
Ground Ground — switch — 0V
(B)
ON

Ignition
15 28 Sound signal center speak-
Output switch Sound signal output
(V) (O) er
ON

SKIB3609E

Ignition
18 32
Sound signal front LH Input switch Sound signal output
(R) (G)
ON

SKIB3609E

Ignition
19 20
Sound signal front RH Input switch Sound signal output
(O) (W)
ON

SKIB3609E

Ignition
21 22
Sound signal rear LH Input switch Sound signal output
(V) (LG)
ON

SKIB3609E

Revision: 2008 August AV-92 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]
Terminal
Description
(Wire color) Reference value A
Condition
Input/ (Approx.)
+ – Signal name
Output
B

Ignition
23 33 C
Sound signal rear RH Input switch Sound signal output
(W) (R)
ON

SKIB3609E D
Ignition
25
Ground Woofer Amp. ON signal Output switch — 12.0 V
(G)
ACC E
Ignition
31
Ground BOSE amp. ON signal Input switch — 12.0 V
(L)
ACC
F

Ignition G
37 27
Sound signal tweeter RH Output switch Sound signal output
(O) (W)
ON

H
SKIB3609E

AV

Revision: 2008 August AV-93 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]
Wiring Diagram - BOSE AUDIO - INFOID:0000000004535237

JCNWM1642GB

Revision: 2008 August AV-94 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1643GB

Revision: 2008 August AV-95 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1644GB

Revision: 2008 August AV-96 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1645GB

Revision: 2008 August AV-97 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1646GB

Revision: 2008 August AV-98 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1647GB

Revision: 2008 August AV-99 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1648GB

Revision: 2008 August AV-100 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1649GB

Revision: 2008 August AV-101 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1650GB

Revision: 2008 August AV-102 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1651GB

Revision: 2008 August AV-103 2009 Rogue

 BOSE AMP.
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1652GB

Revision: 2008 August AV-104 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]
WOOFER
A
Reference Value INFOID:0000000004535351

TERMINAL LAYOUT B

JPNIA0513ZZ E

PHYSICAL VALUES
F
Terminal
Description
(Wire color) Reference value
Condition
Input/ (Approx.) G
+ – Signal name
Output

H
Ignition
2 1
Sound signal woofer Output switch Sound signal output
(Y) (BR)
ON I

SKIB3609E

3 — Shield — — — — J
Ignition
4
Ground Woofer amp. ON signal Input switch — 12.0 V
(G)
ON K
Ignition
5
Ground GND — switch — 0V
(B)
ON L
Ignition
6
Ground Battery power supply Input switch — Battery voltage
(SB)
OFF
M

AV

Revision: 2008 August AV-105 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]
Wiring Diagram - BOSE AUDIO - INFOID:0000000004535353

JCNWM1642GB

Revision: 2008 August AV-106 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1643GB

Revision: 2008 August AV-107 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1644GB

Revision: 2008 August AV-108 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1645GB

Revision: 2008 August AV-109 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1646GB

Revision: 2008 August AV-110 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1647GB

Revision: 2008 August AV-111 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1648GB

Revision: 2008 August AV-112 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1649GB

Revision: 2008 August AV-113 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1650GB

Revision: 2008 August AV-114 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1651GB

Revision: 2008 August AV-115 2009 Rogue

 WOOFER
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1652GB

Revision: 2008 August AV-116 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]
SATELLITE RADIO TUNER
A
Reference Value INFOID:0000000004235180

TERMINAL LAYOUT B

JSNIA0761ZZ E

PHYSICAL VALUES
F
Terminal Description
Reference value
Input/ Condition
+ – Signal name (Approx.)
Output G

H
Ignition
2 1 Satellite radio sound signal When satellite radio mode
Output switch
(L) (R) LH is selected
ON
I
SKIB3609E

Ignition
4 3 Satellite radio sound signal When satellite radio mode
Output switch
(W) (G) RH is selected K
ON

SKIB3609E
L
5 — Shield — — — —
6 — Shield — — — —
M

Ignition
8 Request signal When satellite radio mode
(Y)
Ground
(SAT TO AUDIO)
Output switch
is selected
AV
ON

JSNIA0675ZZ O

Ignition P
9 Communication signal When satellite radio mode
Ground Output switch
(G) (SAT-AUDIO) is selected
ON

PKIB5039J

Revision: 2008 August AV-117 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]
Terminal Description
Reference value
Input/ Condition
+ – Signal name (Approx.)
Output

Ignition
10 Communication signal When satellite radio mode
Ground Input switch
(L) (AUDIO→SAT) is selected
ON

SKIA9301J

Ignition
12
Ground Battery power supply Input switch — Battery voltage
(BR)
OFF
Ignition
16
Ground ACC power supply Input switch — Battery voltage
(SB)
ACC
Satellite radio antenna sig-
31 — Input — — —
nal

Revision: 2008 August AV-118 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]
Wiring Diagram - BOSE AUDIO - INFOID:0000000004535238

AV

JCNWM1642GB
P

Revision: 2008 August AV-119 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1643GB

Revision: 2008 August AV-120 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1644GB

Revision: 2008 August AV-121 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1645GB

Revision: 2008 August AV-122 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1646GB

Revision: 2008 August AV-123 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1647GB

Revision: 2008 August AV-124 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1648GB

Revision: 2008 August AV-125 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1649GB

Revision: 2008 August AV-126 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1650GB

Revision: 2008 August AV-127 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1651GB

Revision: 2008 August AV-128 2009 Rogue

 SATELLITE RADIO TUNER
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1652GB

Revision: 2008 August AV-129 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]
TEL ADAPTER UNIT
Reference Value INFOID:0000000004235182

TERMINAL LAYOUT

JPNIA0011ZZ

PHYSICAL VALUES

Terminal
Description
(Wire color) Reference value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
1
Ground Battery power supply Input switch — Battery voltage
(BR)
OFF
Ignition
2
Ground ACC power supply Input switch — Battery voltage
(SB)
ACC
Ignition
3
Ground Ignition signal Input switch — Battery voltage
(W)
ON
Ignition
4
Ground Ground — switch — 0V
(B)
ON
6 — Shield — — — —

Ignition
7 8
Microphone signal Input switch Give a voice
(B) (R)
ON

SKIB3609E

Sound signal Ignition During voice guide output

9 10
(Telephone voice, tele- Output switch with the switch
(BR) (Y)
phone guidance) ON pressed

SKIB3609E

While using hands-free

Ignition 0V
11 phone system
Ground Telephone ON signal Output switch
(O) While not using hands-free
ON 5.0 V
phone system

Revision: 2008 August AV-130 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]
Terminal
Description
(Wire color) Reference value A
Condition
Input/ (Approx.)
+ – Signal name
Output

0V B
Keep pressing switch
Keep pressing SEEK UP
Ignition 1.25 V
12 14 switch
Steering switch signal A Input switch C
(W) (GR) Keep pressing SEEK
ON 2.5 V
DOWN switch
Except for above 5.0 V
D
Keep pressing VOL DOWN
0V
switch
Keep pressing VOL UP
1.25 V E
switch
Ignition
13 14
Steering switch signal B Input switch Keep pressing
(Y) (GR) 2.5 V
ON switch
F
Keep pressing SOURCE
3.7 V
switch
Except for above. 5.0 V G
Ignition
14 Steering switch signal
Ground — switch — 0V
(GR) ground
ON
H
Keep pressing SOURCE
0V
switch

Ignition Keep pressing SEEK UP

17 19 1.1 V I
Steering switch signal A Output switch switch
(W) (GR)
ON Keep pressing VOL UP
2.2 V
switch
J
Except for above 3.3 V
Keep pressing SEEK
1.1 V
DOWN switch
Ignition K
18 19
Steering switch signal B Output switch Keep pressing VOL DOWN
(L) (GR) 2.2 V
ON switch
Except for above 3.3 V L
Ignition
19 Steering switch signal
Ground — switch — 0V
(GR) ground
ON
M
Ignition
21
Ground Control signal — switch — 0V
(B)
ON
Ignition
AV
22
Ground Control signal — switch — 0V
(B)
ON
Ignition O
23
Ground Control signal — switch — 0V
(B)
ON
Ignition P
24
Ground Ground — switch — 0V
(B)
ON

Revision: 2008 August AV-131 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]
Terminal
Description
(Wire color) Reference value
Condition
Input/ (Approx.)
+ – Signal name
Output
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
Ignition
28 Vehicle speed signal When vehicle speed is ap-
Ground Input switch
(G) (2-pulse) prox. 40 km/h (25MPH)
ON

JSNIA0015GB

Ignition
29
Ground Microphone power supply Output switch — 5.0 V
(W)
ON
33 — TEL antenna signal Input — — —
34 — Shield — — — —
35 AV communication signal Input/
— — — —
(L) (H) Output
36 AV communication signal Input/
— — — —
(P) (L) Output
37 — Shield — — — —
39
— Data line — — — —
(W)
40
— Data line — — — —
(W)
41
— Data line — — — —
(R)
42
— Data line — — — —
(R)

Revision: 2008 August AV-132 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]
Wiring Diagram - BOSE AUDIO - INFOID:0000000004535239

AV

JCNWM1642GB
P

Revision: 2008 August AV-133 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1643GB

Revision: 2008 August AV-134 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1644GB

Revision: 2008 August AV-135 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1645GB

Revision: 2008 August AV-136 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1646GB

Revision: 2008 August AV-137 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1647GB

Revision: 2008 August AV-138 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1648GB

Revision: 2008 August AV-139 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1649GB

Revision: 2008 August AV-140 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1650GB

Revision: 2008 August AV-141 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

JCNWM1651GB

Revision: 2008 August AV-142 2009 Rogue

 TEL ADAPTER UNIT
< ECU DIAGNOSIS > [BOSE AUDIO]

AV

JCNWM1652GB

Revision: 2008 August AV-143 2009 Rogue

 AUDIO SYSTEM SYMPTOMS
< SYMPTOM DIAGNOSIS > [BOSE AUDIO]

SYMPTOM DIAGNOSIS
AUDIO SYSTEM SYMPTOMS
Symptom Table INFOID:0000000004235184

AUDIO SYSTEM

Symptoms Check items Possible malfunction location / Action to take

• Audio unit power supply and ground circuit. Refer to AV-49,
"AUDIO UNIT : Diagnosis Procedure".
• BOSE amp. power supply and ground circuit. Refer to AV-
No sound from all speakers.
49, "BOSE AMP. : Diagnosis Procedure".
• Amp. ON signal circuit. Refer to AV-71, "Diagnosis Proce-
dure".
Audio sound is not heard.
• Sound signal woofer circuit
Sound is not heard from woofer. • Woofer amp. ON signal circuit. Refer to AV-72, "Diagnosis
Procedure".
Sound is not heard only from the
Sound signal circuit of malfunctioning system.
specific places.
When “RADIO” switch is pressed, it • Satellite radio sound signal circuit
change to satellite radio mode. • Satellite radio antenna
• Satellite radio tuner power supply and ground circuit. Refer
to AV-50, "SATELLITE RADIO TUNER : Diagnosis Proce-
Satellite radio is not received. When “RADIO” switch is pressed, it dure".
does not change to satellite radio • Request signal circuit. Refer to AV-69, "Diagnosis Proce-
mode. dure".
• Communication circuit between audio unit and satellite radio
tuner. Refer to AV-67, "Diagnosis Procedure".

RELATED TO STEERING SWITCH

Symptoms Possible malfunction location / Action to take

Without telephone
• Steering switch signal ground circuit.
Refer to AV-56, "Component Inspection".
All steering switches are not operated.
With telephone
• Steering switch signal ground circuit. Refer to AV-66, "Diagnosis Pro-
cedure".
Only specified switch cannot be operated. Steering switch

“SEEK UP”, “SEEK DOWN” and “ ” switches are not oper- Steering switch signal A circuit (steering switch to TEL adapter unit).
ated. Refer to AV-58, "Diagnosis Procedure".

“ ”, “VOL UP”, “VOL DOWN”, “SOURCE” switches are Steering switch signal B circuit (steering switch to TEL adapter unit).
not operated. Refer to AV-60, "Diagnosis Procedure".

Without telephone
• Steering switch signal A circuit.
“VOL UP”, “SEEK UP” and “SOURCE” switches are not oper- Refer to AV-52, "Diagnosis Procedure".
ated. With telephone
• Steering switch signal A circuit (TEL adapter unit to audio unit).
Refer to AV-64, "Diagnosis Procedure".
Without telephone
• Steering switch signal B circuit.
Refer to AV-54, "Diagnosis Procedure".
“VOL DOWN” and “SEEK DOWN” switches are not operated.
With telephone
• Steering switch signal B circuit (TEL adapter unit to audio unit).
Refer to AV-65, "Diagnosis Procedure".

Revision: 2008 August AV-144 2009 Rogue

 HANS-FREE PHONE SYMPTOMS
< SYMPTOM DIAGNOSIS > [BOSE AUDIO]
HANS-FREE PHONE SYMPTOMS
A
Symptom Table INFOID:0000000004235185

RELATED TO HANDS-FREE PHONE B

®
• Check that the cellular phone is corresponding type (Bluetooth enabled) when the hands-free related mal-
function vehicle is in service before performing a diagnosis.
• There is a case that malfunction occurs due to the version change of the phone type, etc. even though it is a C
corresponding type. Therefore, confirm it by changing the cellular phone to another corresponding type
phone, and check that it operates normally. It is necessary to distinguish whether the cause is the vehicle or
cellular phone. Check to ensure the customer's phone is supported by checking the phone compatibility for
D
the hands-free system.
Simple Check for Bluetooth® Communication
If cellular phone and TEL adapter unit cannot be connected with Bluetooth® communication, following proce- E
dure allows the technician to judge which device has malfunction.
1. Turn on a cellular phone, not connecting Bluetooth® communication.
F
2. Start CONSULT-III, then start Windows®.
3. Set CONSULT-III near a cellular phone.
4. When operated Bluetooth® registration by cellular phone, check G
if CONSULT-III* would be displayed on the device name.
(If other Bluetooth® device is located near cellular phone, a
name of the device would be displayed also.) H
NOTE:
*:Displayed device name is “NISSAN- ”.
• If no device name is displayed, cellular phone is malfunction. I
Repair the cellular phone first, then perform diagnosis.
• If CONSULT-III is displayed on device name, cellular phone is nor-
mal. Perform diagnosis as per the following table. JPNIA0441GB J
Trouble Diagnosis Chart by Symptom

Symptoms Check items Possible malfunction location/Action to take K

Does not recognize cellular
Repeat the registration of cellular phone. TEL adapter unit
phone connection.
• Both the reception and the speech can- L
TEL adapter unit power supply and ground circuit.
not be performed.
Refer to AV-50, "TEL ADAPTER UNIT : Diagnosis Pro-
• Audio cannot be operated by steering
cedure".
Hands-free phone cannot be switch.
M
established. • Both the reception and the speech can-
not be performed. Telephone ON signal circuit.
• Audio can be operated by steering Refer to AV-75, "Diagnosis Procedure".
switch. AV
Sound signal (telephone voice, telephone guidance) cir-
The other party's voice cannot Audio system sound is normal.
cuit
be heard by hands-free phone.
Audio system sound does not sound. Refer to AV-144, "Symptom Table". O
Originating sound is not heard Sound operation function is normal. TEL adapter unit
by the other party with hands- Microphone signal circuit.
free phone communication. Sound operation function does not work. P
Refer to AV-73, "Diagnosis Procedure".
When hands-free phone is in
use, the information (connec-
— AV communication signal (H, L)
tion time etc.) is not displayed
on the audio screen.

RELATED TO STEERING SWITCH

Revision: 2008 August AV-145 2009 Rogue

 HANS-FREE PHONE SYMPTOMS
< SYMPTOM DIAGNOSIS > [BOSE AUDIO]
Symptoms Possible malfunction location / Action to take
Only specified switch cannot be operated. Steering switch

“SEEK UP”, “SEEK DOWN” and “ ” switches are not oper- Steering switch signal A (steering switch to TEL adapter unit) circuit.
ated. Refer to AV-58, "Diagnosis Procedure".

“ ”, “VOL UP”,“VOL DOWN” and “SOURCE” switches Steering switch signal B (steering switch to TEL adapter unit) circuit.
are not operated. Refer to AV-61, "Component Inspection".

Revision: 2008 August AV-146 2009 Rogue

 NORMAL OPERATING CONDITION
< SYMPTOM DIAGNOSIS > [BOSE AUDIO]
NORMAL OPERATING CONDITION
A
Description INFOID:0000000004235186

RELATED TO AUDIO B
• The majority of the audio malfunctions are the result of outside causes (bad CD, electromagnetic interfer-
ence, etc.). Check the symptoms below to diagnose the malfunction.
• The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning. C
Check that noise is caused and/or changed by engine speed, ignition switch turned to each position, and
operation of each piece of electrical equipment. Then determine the cause.
NOTE:
• CD-R is not guaranteed to play because they can contain compressed audio (MP3, WMA) or could be incor- D
rectly mastered by the customer on a computer.
• Check that the CDs carry the Compact Disc Logo. If not, the disc is not mastered to the red book Compact
Disc Standard and may not play. E

Symptoms Cause and Counter measure

Check that the CD was inserted correctly. F
Check that the CD is scratched or dirty.
Check that there is condensation inside the player, and if there is, wait until the condensation is
gone (about 1 hour) before using the player. G
The player will play correctly after it returns to the normal temperature if there is a temperature
Cannot play increase error.
Only the music CD files (CD-DA data) will be played if there is a mixture of music CD files (CD- H
DA data) and MP3/WMA files on a CD.
Files with extensions other than “.MP3”, “.WMA”, “.mp3”, or “.wma” cannot be played.
Check that the finalization process, such as session close and disc close, is done for the disc. I
Check that the CD is protected by copyright.
Poor sound quality Check that the CD is scratched or dirty.
J
It takes a relatively long time before If there are many folder or file levels on the MP3/WMA CD, or if it is a multi session disc, some
the music starts playing. time may be required before the music starts playing.
The songs do not play back in the The playback order is the order in which the files were written by the software, so the files might
K
desired order. not play in the desired order.
Noise resulting from variations in field strength, such as fading noise and multi-path noise, or external noise from trains and other
sources, is not a malfunction.
L
NOTE:
• Fading noise: This noise occurs because of variations in the field strength in a narrow range due to mountains or buildings blocking
the signal.
• Multi-path noise: This noise results from a time difference between the broadcast waves directly from the station arriving at the M
antenna and the waves reflected by mountains or buildings.

RELATED TO TELEPHONE
AV
Symptom Possible cause Possible solution
Close the windows or have other occupants
The voice on the other side is diffi- The interior of the vehicle is too noisy.
be quiet.
O
cult to be heard.
The voice is difficult to reach the The volume of the voice is too low. Speak louder.
other side of the connection.
Pronunciation is unclear. Speak clearly. P

Revision: 2008 August AV-147 2009 Rogue

 PRECAUTIONS
< PRECAUTION > [BOSE AUDIO]

PRECAUTION
PRECAUTIONS
FOR USA AND CANADA
FOR USA AND CANADA : Precaution for Supplemental Restraint System (SRS) "AIR
BAG" and "SEAT BELT PRE-TENSIONER" INFOID:0000000004678934

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIRBAG” and “SEAT BELT” of this
Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
FOR MEXICO
FOR MEXICO : Precaution for Supplemental Restraint System (SRS) "AIR BAG" and
"SEAT BELT PRE-TENSIONER" INFOID:0000000004678933

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.

Revision: 2008 August AV-148 2009 Rogue

 PREPARATION
< PREPARATION > [BOSE AUDIO]

PREPARATION A
PREPARATION
Commercial Service Tools INFOID:0000000004235189
B

Tool name Description

C

D
Power tool Loosening bolts and nuts

E
PBIC0191E

AV

Revision: 2008 August AV-149 2009 Rogue

 AUDIO UNIT
< ON-VEHICLE REPAIR > [BOSE AUDIO]

ON-VEHICLE REPAIR
AUDIO UNIT
Exploded View INFOID:0000000004235190

JSNIA0709ZZ

1. Audio unit

Removal and Installation INFOID:0000000004235191

REMOVAL
1. Remove cluster lid C and cluster lid D. Refer to IP-12, "Exploded View".
2. Remove audio unit mounting screws.
3. Pull out audio unit, remove harness clip, and then disconnect antenna feeder and harness connectors.
4. Remove audio unit and bracket as a unit.
5. Remove brackets from audio unit.
INSTALLATION
Install in the reverse order of removal.

Revision: 2008 August AV-150 2009 Rogue

 BOSE AMP.
< ON-VEHICLE REPAIR > [BOSE AUDIO]
BOSE AMP.
A
Exploded View INFOID:0000000004235192

D
JSNIA0710ZZ

E
: Vehicle front
1. BOSE amp.
F
Removal and Installation INFOID:0000000004235193

REMOVAL G
1. Remove luggage floor spacer assembly (FR, RH). Refer to INT-31, "Removal and Installation".
2. Remove BOSE amp.
H
INSTALLATION
Install in the reverse order of removal.

AV

Revision: 2008 August AV-151 2009 Rogue

 TWEETER
< ON-VEHICLE REPAIR > [BOSE AUDIO]
TWEETER
Exploded View INFOID:0000000004235194

JSNIA0711ZZ

1. Tweeter

Removal and Installation INFOID:0000000004235195

REMOVAL
1. Remove instrument panel. Refer to IP-13, "Removal and Installation".
2. Remove tweeter from instrument panel.
INSTALLATION
Installation is the reverse order of removal.

Revision: 2008 August AV-152 2009 Rogue

 CENTER SPEAKER
< ON-VEHICLE REPAIR > [BOSE AUDIO]
CENTER SPEAKER
A
Exploded View INFOID:0000000004235196

D
JSNIA0712ZZ

E
1. Center speaker

Removal and Installation INFOID:0000000004235197

F
REMOVAL
1. Remove center speaker grille. Refer to IP-12, "Exploded View". G
2. Remove center speaker.
INSTALLATION
Installation is the reverse order of removal. H

AV

Revision: 2008 August AV-153 2009 Rogue

 FRONT SPEAKER
< ON-VEHICLE REPAIR > [BOSE AUDIO]
FRONT SPEAKER
Exploded View INFOID:0000000004235198

JSNIA0713ZZ

1. Front speaker
2. Bracket

Removal and Installation INFOID:0000000004235199

REMOVAL
1. Remove front door finisher. Refer to INT-11, "FRONT DOOR FINISHER : Removal and Installation".
2. Remove front door speaker from bracket.
INSTALLATION
Install in the reverse order of removal.

Revision: 2008 August AV-154 2009 Rogue

 REAR SPEAKER
< ON-VEHICLE REPAIR > [BOSE AUDIO]
REAR SPEAKER
A
Exploded View INFOID:0000000004235200

D
JSNIA0714ZZ

E
1. Rear speaker

Removal and Installation INFOID:0000000004235201

F
REMOVAL
1. Remove rear door finisher. Refer to INT-14, "REAR DOOR FINISHER : Removal and Installation". G
2. Remove rear speaker.
INSTALLATION
Installation is the reverse order of removal. H

AV

Revision: 2008 August AV-155 2009 Rogue

 WOOFER
< ON-VEHICLE REPAIR > [BOSE AUDIO]
WOOFER
Exploded View INFOID:0000000004235202

JSNIA0715ZZ

: Vehicle front
1. Clamp
2. Woofer

Removal and Installation INFOID:0000000004235203

REMOVAL
1. Remove luggage floor center box. Refer to INT-31, "Removal and Installation".
2. Remove clamp, and then remove woofer.
INSTALLATION
Install in the reverse order of removal.

Revision: 2008 August AV-156 2009 Rogue

 SATELLITE RADIO TUNER
< ON-VEHICLE REPAIR > [BOSE AUDIO]
SATELLITE RADIO TUNER
A
Exploded View INFOID:0000000004235204

D
JSNIA0716ZZ

E
1. Satellite radio tuner

Removal and Installation INFOID:0000000004235205

F
REMOVAL
1. Remove luggage side lower finisher (LH). Refer to INT-31, "Removal and Installation". G
2. Remove satellite radio tuner.
INSTALLATION
Install in the reverse order of removal. H

AV

Revision: 2008 August AV-157 2009 Rogue

 RADIO & SATELLITE RADIO ANTENNA
< ON-VEHICLE REPAIR > [BOSE AUDIO]
RADIO & SATELLITE RADIO ANTENNA
Exploded View INFOID:0000000004235206

JSNIA0717ZZ

Antenna base & satellite radio anten-

1. Antenna rod 2.
na

Removal and Installation INFOID:0000000004235207

REMOVAL
1. Remove headlining assembly. Refer to INT-23, "NORMAL ROOF : Removal and Installation" (normal roof
models) or INT-26, "SUNROOF : Removal and Installation" (sunroof models).
2. Remove nuts, and then remove radio & satellite radio antenna.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Be careful about tightening torque. Antenna sensitivity becomes poor, and when it is excessive, roof
panel may be deformed, when roof antenna mounting nut tightening torque is loose.

Revision: 2008 August AV-158 2009 Rogue

 STEERING SWITCH
< ON-VEHICLE REPAIR > [BOSE AUDIO]
STEERING SWITCH
A
Exploded View INFOID:0000000004235208

Refer to SR-5, "Exploded View". B

Removal and Installation INFOID:0000000004235209

REMOVAL C
Refer to SR-5, "Removal and Installation".
INSTALLATION
D
Installation is the reverse order of removal.

AV

Revision: 2008 August AV-159 2009 Rogue

 MICROPHONE
< ON-VEHICLE REPAIR > [BOSE AUDIO]
MICROPHONE
Exploded View INFOID:0000000004235210

JSNIA0132ZZ

1. Microphone

Removal and Installation INFOID:0000000004235211

REMOVAL
1. Remove map lamp. Refer to INL-65, "Removal and Installation".
2. Remove microphone from map lamp.
INSTALLATION
Installation is the reverse order of removal.

Revision: 2008 August AV-160 2009 Rogue

 TEL ADAPTER UNIT
< ON-VEHICLE REPAIR > [BOSE AUDIO]
TEL ADAPTER UNIT
A
Exploded View INFOID:0000000004235212

D
JSNIA0718ZZ

E
1. TEL adapter unit

Removal and Installation INFOID:0000000004235213

F
REMOVAL
1. Remove luggage side lower finisher (RH). Refer to INT-31, "Removal and Installation". G
2. Remove TEL adapter unit.
INSTALLATION
Install in the reverse order of removal. H

AV

Revision: 2008 August AV-161 2009 Rogue

 TEL ANTENNA
< ON-VEHICLE REPAIR > [BOSE AUDIO]
TEL ANTENNA
Exploded View INFOID:0000000004235214

JSNIA0719ZZ

1. TEL antenna
2. TEL adapter unit

Removal and Installation INFOID:0000000004235215

REMOVAL
1. Remove luggage side upper finisher (RH). Refer to INT-31, "Removal and Installation".
2. Remove TEL antenna.

Revision: 2008 August AV-162 2009 Rogue

 ANTENNA FEEDER
< ON-VEHICLE REPAIR > [BOSE AUDIO]
ANTENNA FEEDER
A
Location of Antenna INFOID:0000000004235216

AV

P
JSNIA0725GB

Revision: 2008 August AV-163 2009 Rogue