CERABOND 30

Tile adhesives, Joint fillers & Dry mix mortars

HIGH POLYMER MODIFIED TILE ADHESIVE FOR GLASS MOSAIC, STONE CLADDINGS &
ELEVATION TILES

CERABOND 30 is a ready to use high polymer or with a slow speed mixer to make a smooth,
enhanced tile adhesive with high performance for uniform consistent mix.
fixing low porosity and large format tiles. It is Ensure while mixing mechanically to control the
specifically designed for high adhesion and supe- water ratio. After mixing, allow the mixture to
rior tensile strength which is required for fixing stand for 10 - 15 minutes for it to mature. Do not
stone claddings, elevation tiles, and in water add excess water. Remix the paste before apply-
bodies where high water pressure is experienced ing. Apply the mixture over the surface using the
due to diving and acrobatic movements. straight edge of the notched trowel and comb the
applied tile adhesive using the notched side of the
ADVANTAGES trowel to achieve a uniform thickness.
■ Longer pot life A notch trowel of 6-10 mm can be used as per the
■ Self curing properties requirement. Care should be taken to ensure
■ Ready to use material proper coverage of the adhesive on the rear side
■ Waterproofing properties of the tile surface for better adhesion. The tile or
■ Excellent adhesion properties stone shall then be pressed into the tile adhesive
■ Recommended for external cladding for fixing. A rubber hammer or wooden roller shall
■ Tiled floors can be used after 24 hours be used for tapping all four corners of the tile and
■ Accommodate shrinkage cracks due to chang- center which will enable the entrapped air to be
es in weather released & spread the tile adhesive evenly. It also
■ Suitable for heavy duty applications with limited
107G structural movements
helps better binding between the tile & the
&108W substrate.

FUNCTIONS
CERABOND 30 is a ready to use, high performance PROPERTIES
polymer modified tile fixing mortar for low porosity Physical state | Colour Powder | Grey / White
and large format tiles. It is suitable for heavy duty Open time @ 30˚C 40 minutes
applications with moderate structural move-
Pot Life @ 30˚C Approx. 3 Hrs
ments.
Adjustability Approx. 40 minutes

USAGES Mixed density 1.6 - 1.8 Kg / Ltr

■ Can be used on interior and exterior surfaces of Shear adhesion @ 28 days as

≥ 1.75 N/mm2 in dry condition
per IS 15477
leveled floors and cementitious screed
Deformability ≥ 3 mm
■ Can be used on vertical surfaces such as exteri-
Tensile adhesion @ 28 days as
or cladding application as per IS 15477
≥ 1.75 N/mm² in dry condition
BS EN 12004 : 2017

■ Ideally suitable for fiber cement boards, porous

Slip resistance as per EN 1308 0.10 - 0.15 mm
and non porous tiles on walls
C2TES1 TYPE

IS 15477 : 2019 Classification Type 4TES1

■ Best for fixing glass mosaic tiles in the swimming
BS EN 12004 : 2017 Classification C2TES1
pool

METHOD OF USE
Surface Preparation: Note: The working time of CERABOND 30 depends
All laitance, oil, grease, etc., shall be cleaned by upon the temperature and other environmental
IS 15477 : 2019

grinding, wire brushing, chipping, sandblasting, conditions.

high pressure water jet, or chemical etching. Any
uneven surfaces shall be finished level using CERA Do not fix tiles more than 20 ft in height and tile size
LATEX SBR modified mortar. of 1800mm x 1200mm above.
4TES1

Mixing and application: Special Note: For applications with porous tiles it is
Add 4-5 ltr of water for a 20kg bag approximately. advisable to apply lavish coats of CERA EFF PRIMER
The mixing shall be done gradually by hand trowel coat on the rear side and all four sides of the tile.
 Tile adhesives, Joint fillers & Dry mix mortars
COVERAGE
CERABOND 30 will have coverage of 1.25 - 1.75
Sqft/kg for 3 mm bed thickness.
The coverage can vary depending on the surface
condition and also the tile/stone used.

PACKING
20 kg.

SHELF LIFE
12 months in sealed bags if stored in dry condi-
tions.

HEALTH & SAFETY

Avoid contact with the skin for prolonged periods.
In case of any contact with your eyes, wash
immediately with plenty of water and seek medi-
cal attention.

Please consult Cera-Chem technical cell for

further details.
107G
&108W

TILE ADHESIVE
WHITE MARBLE
FIXING OF
QUALITY CONTROL: Cera-Chem products are certified as per ISO 9001: 2015. The chemical composi-
tion and physical properties are tested as per appropriate standards.

Cera-Chem Private Limited also manufactures and markets a wide range of products including: •
Tile adhesives, Joint fillers & Dry mix mortars • Admixtures • Waterproofing solutions • Repair and
Rehabilitation • Protective & Decorative Coating • Flooring Systems • Marble Renewal & Sealer Coats
• Construction Aids
& GLASS MOSAIC

Whilst any information and/or specification contained herein is to the best of our knowledge true and accurate, no
warranty is given or implied in connection with any recommendation or suggestions made by us, our Representatives,
Agents or Distributors, as the conditions of use of any labour involved, site conditions are beyond our control.

CERA-CHEM PRIVATE LIMITED

SUPERIOR CONSTRUCTION CHEMICALS
AN ISO 9001 : 2015 COMPANY
No. 9, First Cross Street, Sterling Road, Nungambakkam,
Chennai-600 034
Tel: 044-48684523, 42652454, 42654525
Trade Enquiry: 98404 80307
Email: corporate@cerachemindia.com
www.cerachemindia.com EDITION 2023