QCBD PENDING WORK O

QCBD# Machine Problem

Polar 1 Stuck Up 4x
Stamping 3 Defective Non stop Mechanism
Stamping 3 Heating Mechanism Problem
CD7 #2 Anilox adjuster for calibration
Window patching Inverter error
2587 Bobst 1 Tab Inserter Malfunction
2,620 Stamping #1 Mis registration problem
N/A CD#1 Chiller Over Temp
2,640 CD7-1 webtech inverter error again
2,638 Corrugator glue motor pump malfunction
2,643 CD7-2 PU7 washerblade lock detached
2,646 IM 1 IM UNUSUAL SOUND TRANSFER SECTION
2,668 Die-cut #1 <Delivery rack misalign please check and repair hard to operate.
2,669 Machine IM 1 - SHAFTING PROBLEM
2,673 improvements
Corrugator Glue pump overflow
2,674 Die-cut #1 feeder main pile lemit switch broken

QCBD DAILY WORK OR

Date: 07/31/24
QCBD# Machine Problem
2,674 Die-cut #1 feeder main pile lemit switch broken
2,675 Die-cut #3 please delivery brush.untighten bolt.
Date: 07/30/24
QCBD# Machine Problem
2,672 Stamping 2 air leak at feeder table
2,673 Corrugator Glue pump overflow
Date: 07/29/24
QCBD# Machine Problem
2,668 Die-cut #1 <Delivery rack misalign please check and repair hard to operate.
2,669 Machine IM 1 - SHAFTING PROBLEM
2,670 improvements
Blanking #1 <enter WO instructions here>
2,671 Blanking #1 STOCK LIFTER MALFUNCTION
Date: 07/27/24
QCBD# Machine Problem
2,662 CD7-1 DISTRIBUTOR ROLLER PU#4 HINDI GUMAGANA
2,663 Gluing 2 <enter WO instructions here>
2,664 Gluing 2 GLUING 1 - FOR REPAIR ENCOUNTER MONITOR COUNTING
2,665 Facilities PROBLEM
<enter WO instructions here>
2,666 Facilities Busted lamp whole sheets sorter at printing area
2,667 Gluing 3 air-leak pre-fold section.
Date: 07/26/24
QCBD# Machine Problem
2,656 6 Wheeler Truck Repair Brake (leak)
2,657 Gluing 3 Replacement
broken belt in of Oil Cap
upper feeder section
2,658 CD6-1 MOBILE REAR EDGE STOPS NOT AT NEUTRAL POSISTION
2,659 Die-cut #3 please check gripper can't adjust opener due to broken bolt
2,660 Die-cut #3 already.nagmimisreg
feeder main pile ayawang takbo.ng sagad kapag may laman.
bumaba
2,661 Counter balance <Forklift Yellow (wontone)- Oil Leakage>
forklift truck
Date: 07/25/24
QCBD# Machine Problem
2,653 E-Flute#2 tanggal ang kadena at feeder section operator side
2,654 Stamping #1 <enter WO instructions here>
2,655 Stamping #1 feeder main pile malfunction.
Date: 07/24/24
QCBD# Machine Problem
2,648 CD6-1 Intermediate holder operator side worn out PU3
2,649 Processor #1 processor1 chiller ay natanggal po yung hose.
2,650 Die-cut #3 Broken platen roller.
2,651 Die-cut #1 water droplets from compressor piping.
2,652 E-Flute#1 lower feeder vacuum pump malfunction, for checking and repair
Date: 07/23/24
QCBD# Machine Problem
2,644 Facilities 3 Bundling Machine of Bindery (for check-up)
2,645 Stamping#3 Pneumatic fitting broken
2,646 IM 1 IM UNUSUAL SOUND TRANSFER SECTION, FORT CHECKING
2,647 MPET AND
MPETREPAIR
suddenly stop while running, for checking and repair.
Date: 07/22/24
QCBD# Machine Problem
2,643 CD7-2 PU7 washerblade lock detached
Date: 07/21/24
QCBD# Machine Problem
2,642 CD6-1 AIR COMPRESSOR MALFUNCTION, ( ATLAS COPCO )
Date: 07/20/24
QCBD# Machine Problem
2,638 Corrugator glue motor pump malfunction (overflow pag nilakasan ang daloy,
delam pag hininaaan)
2,639 CD7-1 <enter WO instructions here>
2,640 CD7-1 webtech inverter error again this is couse of inconsestent reading
2,641 Suprasetter #1 for monitoringunusual
Encountered during running
sound and error
Date: 07/19/24
QCBD# Machine Problem
2,637 Blanking #1 side stooper malfunction, for checking and repair
Date: 07/18/24
QCBD# Machine Problem
2,635 Stamping #1 impression malfunction
2,636 MPET glue -hose barado, for replacement
Date: 07/17/24
QCBD# Machine Problem
2634 Bobst #1 Feeder main pile ayaw umangat
Date: 07/16/24
QCBD# Machine Problem
N/A CD#1 Chiller Over Temp
N/A CD6#1 Intermideate tank over flow
B20-4 & B20-3 HINDI DUMIDIKIT ANG BUNDLER TAPE
KUMAKALAS
2633 Gluing
2632 Bobst #3 Side guide on and off problem
Date: 07/15/24
QCBD# Machine Problem
2631 E-Flute Umaapaw ang tubig sa e flute 1 and 2
2630 Stripper Waste stripper machine worn out chain cover, for repair
Date: 07/14/24
QCBD# Machine Problem
2629 Bobst #1 Delivery main pile malfunction.
Date: 07/13/24
QCBD# Machine Problem
PLATE CLAMP AYAW BUMUKA MAY SINGAW PU#7
2628 CD7#1
Date: 07/12/24
QCBD# Machine Problem
2627 Gluing #2 Conveyor belt manipis na
2626 Gluing #2 Delivery press conveyor mis align
2625 OFF Line UV stop push button not working
2624 IM 1 Delivery conveyor not working
2623 LILA Plasma treat not working
2622 OFF Line UV Delivery fan not working
2621 OFF Line UV N/A
2620 Stamping #1 Mis registration problem
Date: 07/11/24
QCBD# Machine Problem
2619 Bobst #3 Waste conveyor stuck up
2618 Bobst #3 N/A
2617 Bailing 2 Conveyor unusual sound
2616 Window patching air-leak window patching, for repair
2615 Grablift (Yellow) Flat tire
2614 Grablifter N/A
CD7 #2 & #1 Insufficient air supply
CD7 #2 Varnish over flow ( when using matt varnish)
Date: 07/10/24
QCBD# Machine Problem
2613 E-flute #1 Stuck up bearing corrugated feeder roller
2612 E-flute #2 Feeder vacuum unusual sound
2611 Bobst #1 Delivery pile breaker trip off
2610 Gluing #2 Pick and place sticker vacuum problem
2609 MPET Delivery pile malfunction
Date: 07/09/24
QCBD# Machine Problem
2608 E-Flute #1 Upper chain broken
2607 Gluing #2 Air Leak Ejector kicker
2606 Bobst #2 Stripping board lock problem
2605 Bobst #3 Broken chain at stripping section
Date: 07/08/24
QCBD# Machine Problem
2604 Gluing #2 Breaker switch damage
Date: 07/06/24
Machine Problem
2603 Stamping #3 Side guide always error
2602 Bobst #1 Side guide for checking
2601 Bobst #1 Camera chinese language
Date: 07/05/24
QCBD# Machine Problem
2600 Stamping #3 Mahina ang blower
2599 Bobst #1 N/A
Date: 07/04/24
QCBD# Machine Problem
2598 Bobst #1 Feeder Main Pile Malfunction
2597 CD71 Chiller Over Temp
2596 Eflute 2 Lower Feeder Belt Misalign
Date: 07/03/24
QCBD# Machine Problem
2595 CD7#2 Airstar braker trip off
2594 Facilities Water leak from aircon
2593 MPET Delivery main pile malfunction.
2592 UV Delivery Jogger Not Okay
2591 MPET Loose Belt @ Feeder Table
2590 Gluing #3 Bundling machine barado
Date: 07/02/24
QCBD# Machine Problem
2,589 Gluing 2 sealer machine no power due to broken wire, for repair
2,588 Stamping #1 Delivery rack broken.
2,587 Die-cut #1 tab inserter pumapalya ang bilang
2,586 Stamping #1 vacuum notworking
2,585 Gluing 2 oil -leak in glue gun, for checking and repair
Date: 07/01/24
QCBD# Machine Problem
2,582 Die-cut #3 fallen window support in stripping window
2,583 Gluing 2 ejector kicker natanggal, for repair.
2,584 Gluing 2 steel table foot-wheel broken, for repair
Date: 06/29/24
QCBD# Machine Problem
2,580 CD6-1 CIRCULAR LUBRICATION MALFUNCTION
2,581 Die-cut #1 feeder mainpile not working up and down
Date: 06/28/24
QCBD# Machine Problem
2,579 Gluing 2 push- jogger holding clip worn out thread, for repair
2,578 Die-cut #3 allignment flap not working
2,577 Stamping#3 broken side guide sensor knife.
2,576 CD7-1 Over temperature END OF PRESS
2,575 Facilities Pick and Place namin. Ayaw humigop ng vacuum suction
2,574 E-Flute#1 Clutch malfunction keep on alarming
2,573 E-Flute#1 upper chain plastic pusher broken, for replacement
Date: 06/27/24
QCBD# Machine Problem
2,568 CD7-1 Delivery Auxilliary pile support pneumatic cylender defective
2,569 CD7-2 DELIVERY LAMP BUSTED
2,570 Die-cut #1 Camera not working.

2,571 CD6-1 TECHNOTRANS WATER LEVEL TOO HIGH .

2,572 Gluing 1 ENCOUNTER UNSUAL SOUND AT PRE FOLD AREA DUE
Date: 06/26/24
QCBD# Machine Problem
2,564 Die-cut #2 chain at feeder main pile putol ang kabli
2,565 Die-cut #3 please check break,hard tod to inching.
2,566 Gluing 1 Upper roller Hindi nakalapat sa Ejector Disc
2,567 E-Flute#2 flourescent at the lower feeder pundido na
Date: 06/25/24
QCBD# Machine Problem
2,560 Facilities Installation of Tolda in MRF area
2,561 Gluing 4 bundling machine barado, at ayaw dumikit. for checking and repair

2,562 Gluing 4 gluing 4 center upper belt crash-lock section broken, for
replacement.
2,563 Gluing 2 fabrication of plastic cover for extension conveyor.
Date: 06/24/24
QCBD# Machine Problem
2,550 Die-cut #1 Gripper #05 galaw
2,551 MPET flying knife wala malfunction ayaw magcut
2,552 Gluing 2 DELIVERY CONVEYOR NAWALA SA ALIGNMENT
2,553 E-Flute#2 lower feeder metal roller ayaw umikot putol ang kadena
2,554 Die-cut #2 delivery brush misalign
2,555 E-Flute#2 <enter WO instructions here>
2,556 E-Flute#2 hindi na pantay ang pahid nang glue roller
2,557 Stamping#3 vacuum mahina dumakot
2,558 MPET <enter WO instructions here>
2,559 MPET alarm main motor 7.5 malfunction
Date: 06/22/24
QCBD# Machine Problem
2,545 Gluing 3 KICKER AIR HOSE BROKEN (AIR LEAK)
2,546 Stamping #1 machine on & off due to air pressure too low error.
2,547 Gluing 2 air-leak ejector kicker,
2,548 Blanking #2 stock-lifter malfunction, for checking and repair
2,549 CD7-1 Varnish PUMP MALFUNCTION WALANG HIGOP PABABA.
Date: 06/21/24
QCBD# Machine Problem
2,538 Die-cut #1 feeding tablet for adjustment
2,539 Stamping#3 falling piece of gripper bite.
2,540 Polar Cutter #1 installation of Piler with leveling up and down platform.
2,541 MPET flying knife malfunction ayaw magcut
2,542 Gluing 3 bundling machine namamatay during bundling process. for
checking and repair.
2,543 Die-cut #3 clutch unusual smell
2,544 CD7-2 PULL LAY AYAW KUMABIG OPERATOR SIDE.
Date: 06/20/24
QCBD# Machine Problem
2,530 CD7-2 FEEDER SUCTION MALFUNCTION PUMAPALYA ANG HIGOP

2,531 Stamping#3 panel breaker ayw mabuhay

2,532 Die-cut #2 insuficient oil flow error.
2,533 4 Wheeler Truck <NIK4969- 4W (Leak on coolant)>
2,534 Gluing 1 plasma treat namamatay, for checking and repair
2,535 E-Flute#1 feeder sunction malfunction sira ang spring
2,536 Polar Cutter #1 Power Inverter Defective
2,537 E-Flute#1 LOW PRESSURE BLOWER FEEDER MOTOR PUMP
Date: 06/19/24
QCBD# Machine Problem
2,521 Stamping 2 broken pin at adjustable registration in side guide
2,522 Stamping#3 broken bearing at forwarded sucker
2,523 Stamping#3 Broken nozzle hoose.
2,524 CD6-1 Automatic blanket wash up error position pressadjustment PU5
and Delivery sensor detection of rest position, mobile rear edge
does not wok correctly
2,525 Polar Cutter #1 Stuck up (4x)
2,526 Stamping#3 MAHINA ANG HANGIN S FEEDER
2,527 CD7-1 mahina ang aircon
NG WORK ORDER
Status Responsible QCBD#
Pending Heidelberg/E&M 2633
Waiting parts PRS#20650 PQ#16109 PRSDATE6/21/24) E&M 2632
For schedule (Done install 4 pcs for install 20pcs more) E&M/ Peter 2604
Schedule of repair E&M / Zubek 2628
On going check MDT warranty E&M / MDT 2497
E&M 2,544
For schedule mid of august E&M 2,556
Now ok running but for improve condenser water pump E&M 2,588
Pending For checking E&M 2,642
Waiting new gear pump E&M
E&M
Temporary fixed by Peter E&M
Request parts quitation (peter) E&M & Peter
Temporary fixed by Peter E&M & Peter
Waiting new gear pump E&M
For PRS limit switch E&M

WORK ORDER
Status Responsible
For PRS limit switch E&M
Done retight bolt E&M

Status Responsible
Done replace fittings E&M
Waiting new gear pump E&M

Status Responsible
Request parts quitation (peter) E&M & Peter
Temporary fixed by Peter E&M & Peter
N/A E&M
E&M

Status Responsible

Status Responsible
Status Responsible

Status Responsible

Status Responsible
On going checking
Done replace fittings
Temporary fixed by Peter
Done main drive gear box replace bearing

Status Responsible

Status Responsible
Pending For checking

Status Responsible

Pending For checking

N/A E&M
Pending For checking
Done remove paper inside machine E&M

Status Responsible
Done replace pneumatic fittings E&M

Status Responsible
Done replace PLC E&M
Done replace chemical hose Jerry

Status Responsible
Done clean feeder adjuster shafting E&M

Status Responsible
Under observation reset high pressusre error E&M
Done clean intermediate tank E&M

Pending for checking E&M

Pending temporary fixed production E&M

Status Responsible
Done replace sensor and vavle E&M
Done replace new waste stripper E&M

Status Responsible
Done replace magnetic contactor E&M

Status Responsible
Pending schedule repair 7/20/24 E&M Zubek

Status Responsible
Done replace belt E&M
Done align belt E&M
Done relay switch E&M
Done restart machine only E&M Peter Team
Done replace magnetic contactor E&M
Done replace fan E&M
N/A E&M
For schedule mid of august E&M

Status Responsible
Done replace chain E&M
N/A E&M
Done align belt E&M
Done replace pneumatic hose E&M
Done vulcanize tire E&M
N/A E&M
Done stop using centralized air for cleaning of machine E&M
Pending for replacement of high viscosity ARO pump E&M

Status Responsible
Done replace bearing E&M
Done replace bearing E&M
Done reset breaker E&M
Done adjust parameters E&M
Done align sensor E&M

Status Responsible
Done replace chain E&M
Done repair kicker Valco
Done replace bolt E&M
Done replace chain E&M

Status Responsible
Pending for request parts quotation

Status Responsible
Done adjust sensor E/M
Done adjust sensor E&M
Done reprogram E&M

Status Responsible
Done replace vacuum E&M
N/A E&M

Status Responsible
Done check sensor E&M
For testing fixed by jeff E&M
Done Repair E&M

Status Responsible
Done replace cooling motor E&M
Done declogged drainage Jeff aircon tech
Done adjust sensor limit E&M
Done clean bushing E&M
Done retigt loose belt E&M
Done clean guide E&M

Status Responsible
Done replace wire E&M
Order parts needed E&M
For schedule E&M
Done replace bearing E&M
Done replace o-ring E&M

Status Responsible
Done fixed gas spring E&M
Done fixed by valco E&M
For schedule E&M

Status Responsible
Done replace oil pump coupling E&M
Done check sensor E&M
Status Responsible
Done rethread E&M
Done replace bearing E&M
Done replace knife spring E&M
Done clean filter E&M
Done adjust E&M
Done replace relay E&M
Done replace pusher E&M

Status Responsible
Done welding support E&M
Done replace lamp E&M

Done replace power supply E&M

Done check sensor E&M
Done replace bearing E&M

Status Responsible
Done replace cable E&M
Done clean clutch disk E&M
Done adjust setting E&M
Done replace lamp E&M

Status Responsible
Done install tolda E&M

Done replace heater E&M

Done replace belt E&M

Done install cover E&M

Status Responsible
Done adjust chain guide E&M
Done adjust setting E&M
Done align conveyor E&M
Done replace chain E&M
Done align brush E&M
N/A E&M
For replacement of metal roller E&M
Done replace carbon vane E&M
N/A E&M
Done clean vacuum motor E&M

Status Responsible
Done repleace pneumatic hose E&M
Done fixed air leak E&M
Done fixed by valco Valco
Done adjust sensor E&M
Done replace ARO pump E&M

Status Responsible
Done adjus lower support Peter
Done replace gripper bite E&M
?
Done adjust setting E&M

Done fixed shorted wire E&M

Done adjust break Aji
Pending temporary fixed Heidelberg

Status Responsible

Done replace hose E&M

Done replace circuit breaker E&M
Done check pump E&M
E&M
Done replace nozzle E&M
Done replace spring E&M
Done replace power supply' E&M
Done replace bearing E&M

Status Responsible
Done replace pin E&M
Done replace bearing E&M
For replace nozzle E&M

Done replace servo motor/ done check sensor Heidelberg

ED
Done replace carbon vane E&M
Done clean aircon E&M
 DONE PENDIND WORK ORDE
Machine Problem
Gluing B20-4 & B20-3 HINDI DUMIDIKIT ANG BUNDLER TAPE KUMAKALAS
Bobst #3 Side guide on and off problem
Gluing #2 Breaker switch damage
CD7#1 PLATE CLAMP AYAW BUMUKA MAY SINGAW PU#7
Bobst 2 Camera cable not okay
CD7-2 PULL LAY AYAW KUMABIG OPERATOR SIDE.
E-Flute#2 hindi na pantay ang pahid nang glue roller
Stamping #1 Delivery rack broken.
CD6-1 AIR COMPRESSOR MALFUNCTION, ( ATLAS COPCO )
D WORK ORDER
Status Responsible
Done fixed heater support E&M
Done replace lever and adjust sensor setting E&M
Done replace switch 7/19/24 E&M
Done replace block 7/21/24 E&M Zubek
Done replace cable and power supply Webtech
Done clean solenoid valve Heidelberg
Done replace glue roller from rubber to metal E&M / MR. WU
Done replace parts damage E&M
Done replace magnetic contactor E&M