G3516 Engine Electronic Ignition System 4EK00001-UP(SEBP2185 - 97) - Documentation Page 1 of 3
Shutdown SIS
Previous Screen
Product: GAS ENGINE
Model: G3516 GAS ENGINE 4EK
Configuration: G3516 Engine Electronic Ignition System 4EK00001-UP
Specifications
G3500 Engines
Media Number -SENR6411-18 Publication Date -01/04/2014 Date Updated -13/10/2016
i04941229
Camshaft
SMCS - 1210
S/N - 4EK1-UP
S/N - 8BZ1-UP
S/N - 8JZ1-UP
S/N - 8LD1-UP
S/N - 8PW1-UP
S/N - CPG1-UP
S/N - CSZ1-UP
S/N - L6A1-UP
S/N - L6E1-UP
S/N - L6F1-UP
S/N - L6G1-UP
S/N - ZAZ1-UP
S/N - ZBA1-UP
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 8/3/2024
G3516 Engine Electronic Ignition System 4EK00001-UP(SEBP2185 - 97) - Documentation Page 2 of 3
Illustration 1 g03124339
(1) Left-hand camshaft assembly
(2) Right-hand camshaft assembly
Table 1
Specification for 4P-8352 Camshaft Gp
Item Qty Part Specification Description
Thickness of the groove in a new camshaft assembly is
A - -
8.75 ± 0.05 mm (0.344 ± 0.002 inch).
C 1 5B-5821 Dowel Extension of the dowel is 12.0 ± 0.5 mm (0.47 ± 0.02 inch).
D 2 4N-1650 Dowel Extension of the dowel is 22.0 ± 0.5 mm (0.87 ± 0.02 inch).
7N-3218 Thrust Thickness of a new thrust washer is 8.50 ± 0.05 mm
E 2
Washer (0.335 ± 0.002 inch).
Diameter of bearing journals in a new journal camshaft assembly
is 85.88 ± 0.02 mm (3.381 ± 0.001 inch).
F - -
Bore in camshaft bearing after installation is 86.00 ± 0.06 mm
(3.386 ± 0.002 inch).
End play for a new camshaft assembly is 0.15 to 0.35 mm
- - -
(0.006 to 0.014 inch).
3 16 5P-0076 Bolt Torque to 55 ± 7 N·m (41 ± 5 lb ft).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 8/3/2024
G3516 Engine Electronic Ignition System 4EK00001-UP(SEBP2185 - 97) - Documentation Page 3 of 3
Illustration 2 g03125836
Table 2
Item Qty Part Specification Description
Use the following procedure in order to determine the camshaft lobe lift:
1. Measure camshaft lobe height (H).
- - - 2. Measure base circle (J).
3. Subtract the base circle (J) from the camshaft lobe height (H). The
difference is the actual camshaft lobe lift.
Specified camshaft lobe lift:
G - - Inlet lobe is 9.201 mm (0.3622 inch).
Exhaust lobe is 8.699 mm (0.3425 inch).
Copyright 1993 - 2024 Caterpillar Inc. Sat Aug 3 08:24:53 UTC+0330 2024
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/m... 8/3/2024
