TRAK & Sport Bed Mills

Safety, Installation, Maintenance, Service & Parts List Manual

Document: P/N 24941

Version: 012512

Covering Machine Models:

• TRAK TRM
• TRAK DPM
• TRAK DPM5
• SPORT B3
• SPORT B5
• TRAK DPMS3
• TRAK DPMS5
• TRAK DPME2

Covering Non-current Control Models:

• ProtoTRAK MX2 & MX3

• TRAK AGE2 & AGE3
• ProtoTRAK M3
• ProtoTRAK SM
• ProtoTRAK EDGE 3

Southwestern Industries, Inc.

2615 Homestead Place
Rancho Dominguez, CA 90220 USA
T | 310.608.4422 | F | 310. 764.2668
Service Department: 800.367.3165
e-mail: sales@southwesternindustries.com | service@southwesternindustries.com | web: southwesternindustries.com
Copyright © 2011, Southwestern Industries, Inc. All rights are reserved. No part of this
publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, mechanical, photocopying, recording or otherwise, without the prior written
permission of Southwestern Industries, Inc.

While every effort has been made to include all the information required for the purposes of this
guide, Southwestern Industries, Inc. assumes no responsibility for inaccuracies or omission and
accepts no liability for damages resulting from the use of the information contained in this guide.

All brand names and products are trademarks or registered trademarks of their respective
holders.

Southwestern Industries, Inc.

2615 Homestead Place
Rancho Dominguez, CA 90220-5610
Phn 310/608-4422 ‹ Fax 310/764-2668
Service Department
Phn 800/367-3165 ‹ Fax 310/886-8029
Table of Contents
3.2.2 Slow Down Axis
1.0 Safety 3.2.3 Axis Will Not Jog
1.1 Safety Publications 1
3.2.4 Axis Motor Motion Is Not Smooth
1.2 Danger, Warning, Caution, Note Labels &
3.2.5 Vibration in Motion
Notices as Used in this Manual
3.2.6 Searching Axis
1.3 Safety Precautions
3.3 Problems Relating to Operation of Control
3.3.1 Display Blanks
2.0 Installation 3.3.2 Bad Picture on Display
2.1 Floor Plan, Layout & Space Requirements 7 3.3.3 Keyboard Lockup
2.2 Uncrating 3.3.4 Fault X, Y or Z
2.3 Shortages: Inventory Checklist 3.3.5 Problems Reading Floppy Disk
2.4 Installation Instructions & Checklist 3.3.6 System Will Not Turn on or
2.5 Machine Specifications Boot Up
2.6 Maximum Work Capacities 3.3.7 System Reboots by Itself
2.7 Control Hardware 3.3.8 System Shuts Off
2.7.1 TRAK AGE & ProtoTRAK MX 3.3.9 Will Not Hold Calibration
Controls 3.3.10 Auxiliary Functions Not Working
2.7.2 ProtoTRAK M3 Controls – 3.3.11 E-Stop Error
Sport B3 & B5 3.3.12 Limit Switch Error
2.7.3 ProtoTRAK SM Control – 3.4 Problem with the Measurements
DPMS3 & DPMS5 3.4.1 X, Y & Z-Axis Measurements
2.7.4 ProtoTRAK Edge 3 Control – Do Not Repeat
DPME2 3.4.2 X, Y & Z-Axis Measurements
2.8 Lifting and/or Moving the Machine Are Not Accurate
2.9 Releasing the Head Counterweight Supports 3.4.3 The DRO Is Not Counting
2.10 Cleaning 3.4.4 X, Y & Z-Axis DRO Counting in
2.11 Leveling: Tolerance for DPMS is .0005”/10” Wrong Direction
2.12 Electrical Connection 3.4.5 X, Y, & Z-axis Electric Handwheels
2.12.1 Pendant and Wiring Diagrams Turn in Wrong Direction
for TRM, DPM & DPM5 3.5 Problems with the Machine Tool
2.12.2 Pendant and Wiring Diagrams 3.5.1 Z-Axis Noisy
for Sport B3 & B5 3.5.2 Spindle Stalls or Turns Off During
2.12.3 Pendant and Wiring Diagrams Machining
for DPMS3 & DPMS5 3.5.3 Spindle Motor Hums or Will
2.12.4 Pendant and Wiring Diagrams Not Run
for DPME2 – EDGE 3.5.4 Spindle Runs Backwards
2.12.5 Phase Converters 3.5.5 Spindle Motor Intermittently Stops
2.13 Air Connection - Optional and Starts or Does Not Operate
2.14 Mounting the Display Pendant 3.5.6 Head Noise
2.15 Cable Interconnections
2.16 Lubrication 4.0 Diagnostics
2.16.1 Way Lubrication
4.1 The Machine Tool & Set-Up 69
2.16.2 Head Lubrication TRAK Bed Mills
4.1.1 The Milling Machine Checklist
2.17 ProtoTRAK SMX Euclid Block Procedure
4.1.2 A Special Word About X/Y/Z Gibs
4.1.3 Lubrication
3.0 Troubleshooting by Symptom 4.1.4 Machining Set-Up
3.1 Problems Relating to Machining Results 51 4.2 The Mechanical Drive Train (X, Y)
3.1.1 Poor Finish 4.2.1 Ballscrew Alignment
3.1.2 Circles Out of Round 4.3 Computer/Pendant Diagnostics
3.1.3 Taper Cut on a Programmed 4.3.1 Diagnostic for Computer Modules
Straight Line Move Contained in Pendant
3.1.4 Parts Have Incorrect Dimensions 4.3.2 Diagnostics for Computer Modules
3.2 Problems Regarding Motion of Machine Separate from Pendants
3.2.1 Run Away Axis 4.3.2 Checking Floppy Drive by

i
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Formatting a Disk 5.1.11 Z-Axis Screw Removal &
4.4 Motor Diagnostics Replacement
4.4.1 Cable Connections 5.1.12 Air Solenoid Replacement for Power
4.4.2 To Check the Motor Encoders Drawbar – DPMS3/DPMS5 only
4.4.3 Encoder Counts to Pendant 5.1.13 Spindle Motor Wiring
4.4.4 Moving Problem From One Axis 5.1.14 Electric Box Service
to Another 5.1.15 Auxiliary Function Interface
4.5 Servo Drivers 5.1.16 Feed Trip Adjustmemt
4.6 Glass Scales 5.1.17 Quill Clock Spring Replacement &
4.6.1 Alignment of Scales Adjustment
4.6.2 Measurements Do Not Repeat 5.1.18 Spindle Motor Removal &
4.7 TRAK Sensors Replacement
4.7.1 Faulting Axis 5.1.19 Drive Belt Replacement
4.7.2 Measurements Do Not Repeat 5.1.20 Timing Belt Replacement
4.8 Electrical 5.1.21 Brake Shoe Replacement
4.8.1 Checking A/C Voltage 5.1.22 Spindle Replacement
4.8.2 Checking Fuses 5.2 Maintenance
4.8.3 Cable Breakout Box Connections 5.2.1 Gib Adjustments
4.8.4 Cable Connections 5.2.2 Calibration & Backlash Constants
4.9 External Connector Box 5.2.3 Head Rotation and Tramming
4.10 Red LED Diagnostic Status Indicators 5.2.4 Limit Switch Option
4.11 Service Codes 5.2.5 Accuracy and Repeatability
4.11.1 CODE 11: Hysteresis Measurements
4.11.2 Code 12: Feed Forward Constant
4.11.3 Code 33: Software ID
4.11.4 Code 97: System Axis
6.0 Figures & Parts List
2-1 Machine Footprints
Configuration
2-2 Overall Dimensions
4.11.5 Code 100: Axis Open Loop Test
2-3 TRAK & Sport Bed Mills Component
4.11.6 Code 101: X-Axis Motor Encoder
Identification
Test
2-4 TRAK & Sport Bed Mill Rear View
4.11.7 Code 102: Y-Axis Motor Encoder
2-5 Lifting the Machine, Method 1
Test
2-6 Lifting the Machine, Method 2
4.11.8 Code 103: Z-Axis Motor Encoder
2-7 Placement of Levels
Test
2-8 Leveling Screws
4.11.9 Code 123: Calibration
2-9 Pendant Drawer – AGE2/3 & MX2/3
4.11.10 Code 127 - Set X or Y Backlash
2-10 Computer Cabinet – AGE3 & MX3
Constant
Connections – DMP & DPM5
4.11.11 Code 128: Input Backlash
2-11 AGE2 / MX2 Computer Cabinet
Constant
-- TRM
4.11.12 Code 129: Arc Accuracy
2-12 TRM Wiring (P/N 16042) for 1995
4.11.13 Code 314: Toggle Test Lights
and Earlier
‘On’ in Status Line SM only
2-13 Electrical Box Connections – DPM
4.11.14 Code 319: Error Log – SM only
& DPM5
2-14 Wiring Diagram – DPM & DPM5
5.0 Procedures for Replacements 2-14 (continued)
& Maintenance 2-15 M3 Pendant Display Basic
5.1 Replacements 96 Configuration – Sport B3 & B5
5.1.1 Servo Motor Replacement 2-16 Wiring the Sport B3 & B5
5.1.2 Servo Driver Replacement 2-17 Sport B3 & B5 – Electric Box
5.1.3 Computer Module Connections
5.1.4 System Flash Disk Replacement 2-18 Schematic Standard Electric Box –
5.1.5 Cable Routing on Machine Sport B3 & B5
5.1.6 TRAK Sensor Replacement 2-19 Pendant Cable Connections – SM
5.1.7 Glass Scale Replacement 2-20 Pendant – SM
5.1.8 Power Drawbar 2-21 Wiring the DPMS3 & DPMS5
5.1.9 Ball Screw Replacement, X-Axis 2-22 Edge 3 Pendant Rear – DPME2
(Table), DPMSX2 2-23 Electrical Box without Transformer –
5.1.10 Ball Screw Replacement, Y-Axis DPME2
(Saddle), DPMSX2 2-24 Electrical Schematic – DPEM2

ii
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 2-25 Cable Interconnections – TRM/MX2 5-37 Table Gib Adjustment
2-26 Cable Interconnections – DPM & 5-38 Table Gib Screw
DPM5 5-39 Table Gib & Saddle Bottom Gib
2-27 Cable Interconnections – Sport B3 Adjustment
2-28 Cable Interconnections – Sport B5 5-40 Saddle Side Gib Adjustment
2-29 Cable Connection Diagram – DPMS3 5-41 Saddle Bottom Gib Adjustment
& DPMS5 TRM, DPM, Sport B3, DPMS3
2-30 Cable Connection Diagram – DPME2 5-42 Ram Back Gib
2-31 Euclid Block 5-43 Ram Side Gib Adjustment
4-1 Electrical Box Schematic 5-44 Calibration Set-Up
4-2 Electrical Box Schematic – DPME2 5-45 Tramming of Head
5-1 Servo Driver Replacement 4-46 Typical Set-Up for X-Axis Accuracy/
5-2 Computer Module Replacement Repeatability Check
-- Edge 5-47 Typical Set-Up for Y-Axis Accuracy/
5-3 Computer Module & Flash Drive Repeatability Check
Replacement – SM3 5-48 Typical Set-Up for Z-Axis Accuracy/
5-4 M5 Base Mounting Repeatability Check
5-5 TRAK Sensor Mounting 5-49 Program Movement
5-6 DPMS3 Sensor Assembly
5-7 DPMS5 Sensor Assembly
5-8 Z Axis Glass Scale Assembly 100 Top House Assembly 184
5-9 Glass Scale Alignment – TRM, DPM, 101 Gear Housing Sub-Assembly
Sport B3 & DPMS3 102 Hi-Low Shift Clutch Sub-Assembly
5-10 Glass Scale Alignment – DPM5, 103 Hi-Low Shift Sub-Assembly
Sport B5, DPMS5 104 Pulley Pinion Sub-Assembly
5-11 Power Drawbar Assembly 105 Lower Vari-Disc Sub-Assembly
5-12 X Drive Assembly for TRM, DPM, 106 Upper Vari-Disc Sub-Assembly
& Sport B3 107 Speed Change Handwheel Sub-
5-13 X Drive Assembly, left side, DPME2 Assembly
5-14 X Drive Assembly, DPM5 & 108 Spindle Motor Sub-Assembly
Sport B5 109 Bottom Housing Assembly
5-15 X-Axis Drive Assembly – DPMS3 110 Worm Gear Cradle Sub-Assembly
5-16 X Drive Train – DPMS5 111 Quill Feed Selector Sub-Assembly
5-17 X Handwheel Drive Mechanism -- 112 Quill Pinion Shaft Sub-Assembly
DPMS5 Only 113 Overload Clutch Trip Sub-Assembly
5-18 X Axis Drive Assembly – DPME2 114 Feed Reverse Clutch Sub-Assembly
5-19 Ball Screw Yoke Assembly – 115 Spindle Sub-Assembly
TRM & DPM 118 Head Top Assembly
5-20 Y Drive Assembly – TRM & DPM 119 Gear Housing
5-21 Y Drive Assembly – DPM5 & 120 Hi-Low Shift Clutch Sub-Assembly
Sport B5 121 Hi-Low Shift (DPEM2)
5-22 Y Drive Assembly – Sport B3 122 Pulley Pinion (DPEM2)
5-23 Y Drive Train – DPMS3 123 Lower Vari-Disc Drive (DPEM2)
5-24 Y Drive Train – DPMS5 124 Upper Vari-Disc Drive (DPEM2)
5-25 Y Drive Train – DPME2 125 Speed Change Handwheel (DPEM2)
5-26 Z Axis Motor & Ball Screw – 126 Spindle Motor (DPME2)
DPM, DPM5, Sport B3, & Sport B5 127 Lower Head Assembly (DPEM2)
5-27 Z Axis Drive Assembly – DPMS3 & 128 Worm Gear Cradle (DPEM2)
DPMS5 129 Quill Feed Selector (DPEM2)
5-28 DPME2 Z-Axis Drive Train 130 Quill Pinion Shaft (DPEM2)
5-29 Power Drawbar 131 Overload Clutch Trip (DPEM2)
5-30 Spindle Motor Wiring (Except 132 Feed Reverse Clutch (DPEM2)
DPME2) 133 Spindle Assembly (DPEM2)
5-31 Spindle Motor Wiring – Spindle 134 Head Top Housing
Control – DPME2 only 135 Head Back Gear
5-32 Feed Trip Adjustment 136 Head Lower Housing
5-33 Quill Clock Spring Replacement 137 Lubrication System (TRM)
5-34 Drive Belt Replacement 138 Lubrication System (DPM,
5-35 Drive Belt Replacement Sport B3, Sport B5)
5-36 Spindle Replacement 139 Lubrication, Pump & Ram
iii
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 140 Lubrication X, Y & Z (DPMS3)
141 Lubrication System, X & Y Axis
DPM5 & DPMS5
142 Pump & Lube System (DPEM2)
143 Lubrication Drawing, X & Y Axis
144 Head/Ram Riser Drive System
145 Electronic Hand Wheel Assembly

iv
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
1.0 Safety
The safe operation of TRAK and Sport Bed mills depends on its proper use and the precautions
taken by each operator.

• Read and study this manual and your model’s corresponding Programming, Operating,
and Care Manual. Be certain every operator understands the operation and safety
requirements of this machine before its use.

• Always wear safety glasses and safety shoes.

• Always stop the spindle and check to ensure the CNC control is in the stop mode before
changing or adjusting the tool or workpiece.

• Never wear gloves, rings, watches, long sleeves, neckties, jewelry, or other loose items
when operating or around the machine.

• Use adequate point of operation safeguarding. It is the responsibility of the employer to

provide and ensure point of operation safeguarding per OSHA 1910.212 - Milling
Machine.

1.1 Safety Publications

Refer to and study the following publications for assistance in enhancing the safe use of this
machine.

Safety Requirements for Manual Milling, Drilling, and Boring Machines with or
without Automatic Control (ANSI B11.8-2001). Available from The American National
Standards Institute, 1819 L Street N.W., Washington D.C. 20036

Concepts And Techniques of Machine Safeguarding (OSHA Publication Number 3067).

Available from The Publication Office - O.S.H.A., U.S. Department of Labor, 200 Constitution
Avenue, NW, Washington, DC 20210.

1.2 Danger, Warning, Caution, and Note Labels & Notices As

Used In This Manual
DANGER - Immediate hazards that will result in severe personal injury or death. Danger labels
on the machine are in red.

WARNING - Hazards or unsafe practices that could result in severe personal injury and/or
damage to the equipment. Warning labels on the machine are in orange.

CAUTION - Hazards or unsafe practices, which could result in minor personal injury or
equipment/product damage. Caution labels on the machine are in yellow.

NOTE - Call attention to specific issues requiring special attention or understanding.

1
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Safety & Information Labels Used On The
TRAK Bed Milling Machines
It is forbidden by OSHA regulations and by law to deface, destroy or remove any
of these labels

2
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Power Requirements at 220 and 440 Volts, 3-phase 60 HZ
DPME2 TRM, DPM, DPM5 Sport B3 Sport B5 DPMS3 DPMS5
Overload Setting - 11 A 8.5 A 8.5 A 14 A 8.5 A 14 A 8.5 A 14 A
220 V
Overload Setting - n/a 4.25 A 4.25 A 7A 4.25 A 7A 4.25 A 7A
440 V
FLA of Largest Motor 11 A 8.5 A 8.5 A 14 A 8.5 A 14 A 8.5 A 14 A
at 220 V
FLA of Largest Motor n/a 4.25 A 4.25 A 7A 4.25 A 7A 4.25 A 7A
at 440 V
FLA of Machine at 11 A 8.5 A 8.5 A 14 A 8.5 A 14 A 8.5 A 14 A
220 V
FLA of Machine at n/a 4.25 A 4.25 A 7A 4.25 A 7A 4.25 A 7A
440 V

3
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
1.3 Safety Precautions
1. Do not operate the machine before this TRAK Bed and Sport Mills Installation,
Maintenance, Service and Parts List Manual and also your model's corresponding
Programming, Operating & Care Manual have been studied and understood.

2. Do not run this machine without knowing the function of every control key, button, knob,
or handle. Ask your supervisor or a qualified instructor for help when needed.

3. Protect your eyes. Wear approved safety glasses (with side shields) at all times.

4. Don't get caught in moving parts. Before operating this machine remove all jewelry
including watches and rings, neckties, and any loose-fitting clothing.

5. Keep your hair away from moving parts. Wear adequate safety headgear.

6. Protect your feet. Wear safety shoes with oil-resistant, anti-skid soles, and steel toes.

7. Take off gloves before you start the machine. Gloves are easily caught in moving parts.

8. Remove all tools (wrenches, chuck keys, etc.) from the machine before you start. Loose
items can become dangerous flying projectiles.

9. Never operate a milling machine after consuming alcoholic beverages, or taking strong
medication, or while using non-prescription drugs.

10. Protect your hands. Stop the machine spindle and ensure that the CNC control is in the
stop mode:

• Before changing tools

• Before changing parts

• Before you clear away the chips, oil or coolant. Always use a chip scraper or brush

• Before you make an adjustment to the part, fixture, coolant nozzle or take
measurements

• Before you open safeguards (protective shields, etc.). Never reach for the part,
tool, or fixture around a safeguard.

11. Protect your eyes and the machine as well. Don't use compressed air to remove the
chips or clean the machine.

12. Disconnect power to the machine before you change belts, pulley, and gears.

13. Keep work areas well lighted. Ask for additional light if needed.

14. Do not lean on the machine while it is running.

15. Prevent slippage. Keep the work area dry and clean. Remove the chips, oil, coolant and
obstacles of any kind around the machine.

4
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
16. Avoid getting pinched in places where the table, saddle or spindle head create "pinch
points" while in motion.

17. Securely clamp and properly locate the workpiece in the vise, on the table, or in the
fixture. Use stop blocks to prevent objects from flying loose. Use proper holding
clamping attachments and position them clear of the tool path.

18. Use correct cutting parameters (speed, feed, depth, and width of cut) in order to prevent
tool breakage.

19. Use proper cutting tools for the job. Pay attention to the rotation of the spindle: Left
hand tool for counterclockwise rotation of spindle, and right hand tool for clockwise
rotation of spindle.

20. After an emergency stop, always turn the FORWARD/REVERSE switch to "Off" (STOP)
before releasing or resetting the E-Stop.

21. Prevent damage to the workpiece or the cutting tool. Never start the machine (including
the rotation of the spindle) if the tool is in contact with the part.

22. Check the direction (+ or -) of movement of the table, saddle and ram when using the
jog or power feed.

23. Don't use dull or damaged cutting tools. They break easily and become airborne.
Inspect the sharpness of the edges, and the integrity of cutting tools and their holders.
Use proper length for the tool.

24. Large overhang on cutting tools when not required result in accidents and damaged
parts.

25. Handwheels must have the crank folded inside when using CNC programmed machining
or rapid feeds, power feed or jog.

26. Prevent fires. When machining certain materials (magnesium, etc.) the chips and dust
are highly flammable. Obtain special instruction from you supervisor before machining
these materials.

27. Prevent fires. Keep flammable materials and fluids away from the machine and hot,
flying chips.

28. Changing the speed of rotation of the spindle must be done while the rotation is on. It
is recommended to stop and start the spindle at a low rate of speed.

29. Interlocked Table Guards. Interlocked table guards may be purchased from
Southwestern Industries, Inc. if deemed necessary by the user.

5
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
2.0 Installation
Read and understand this entire installation section before beginning the installation procedure.

2.1 Floor Plan, Layout & Space Requirements –

TRAK & Sport Bed Mills

Figure 2-1
Machine Footprints
DPME2 TRM, DPM, Sport B3, DPM5, Sport B5,
DPMS3 DPMS5
Footprint of Machine 23.1” x 40.5” 24” x 44” 24” x 48.4”
Weight (approximate) net 3200 lbs. 4100 lb. 4400 lb.
Weight (approximate) shipping 3500 lbs. 4400 lb. 4700 lb.
Pallet Size 70” x 70” 6’ x 6’ 6’ x 6’
A Overall width 101” 108” 136”
B Overall length w/ electric 72” 76” 81”
box door open
C Bed width 23.125” 24” 24”
D Bed width between leveling 20.5” 21.7” 21.7”
screws
E Distance between leveling 32.5” 18.1” 20.5”
screws
F Bed length 40.5” 43.3” 48.4”

6
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 Figure 2-2
Overall Dimensions
DPME2 TRM, DPM, Sport DPM5, Sport B5,
B3, DPMS3 DPMS5
G Height of table from bottom of 34” 38” 41”
bed
H Maximum distance from 23.5” 23.5” 23.5”
spindle nose to table
I Maximum height of machine 78” 85” 87”
from bottom of bed to top of
column cover.
J Height of machine from bottom 89” 95” 98”
of bed to top of spindle motor
K Width of machine including 70” 73” 70”
table
L Length of machine with electric 64” 66” 71”
box door closed

7
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
2.2 Uncrating
Carefully remove the wood crate and protective packaging, paying attention not to scratch,
damage, or mar any parts of the machine.

Remove the cardboard boxes with the PENDANT DISPLAY (handle carefully), the box
containing the TOOL BOX and Z crank. The leveling pads and screws for the machine can be
found in the toolbox. The Y way covers are shipped in a separate tube. The lower Z way cover
can be found in a box as well.

Remove two steel bars - 1.0 inch in diameter. These items are necessary for lifting and moving
the machine.
Loosen and remove 4 screws and nuts holding the machine to the wood pallet.

ATTENTION!
Immediately report, in writing, any damages observed at this time that can be attributed to the
transportation or improper handling/moving of the machine.

2.3 Shortages: Inventory Checklist

_____ Machine (check model and serial number)
______ Manual drawbar with washer
______ Leveling pads (B239) and screws (B240). Note: 4 each for DPME2 and 6 each for TRM,
DPM, DPM5, Sport B3, Sport B5, DPMS3, DPMS5
______ Table tray with rubber pad (assembled to machine) (TRM, DPM, SPORT B3,
DPMS3) (15977)
______ Pendant Display with four 1/4-20 screws for mounting
______ Pendant Arm assembled to the column
______ Toolbox with various tools
______ Safety, Operation & Programming Manual for either ProtoTRAK SM, MX, M3,
EDGE 3 or TRAK AGE
______ TRAK & SPORT BED MILLS Safety, Installation, Maintenance, Service & Parts
List Manual (P/N 24941)
______ Table trays (DPM5, SPORT B5, DPMS5 only)
______ Manual Z-axis crank (16526) (TRM, DPM, DPM5, Sport B3, Sport B5, DPMS3,
DPMS5)
______ Way covers DPME2 – front (23676) and rear (23677) of saddle
______ Way covers DPME2 - bottom on column (23675), top on column (23675)
______ Way covers TRM, DPM, SPORT B3, DPMS3 – front (B268) and rear (B267)
of saddle
______ Way covers DPM5, SPORT B5, DPMS5 – front (B268) and rear (B267-1) of saddle

8
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
______ Way covers TRM, DPM, DPM5, Sport B3, Sport B5, DPMS3, DPMS5- bottom on column
(B202), top on column (B201)

In case of shortages, contact the representative from whom you purchased the machine.

2.4 Installation Instructions & Checklist

Installer: Use this checklist to assure a complete set-up of the TRAK or SPORT BED MILL.
1. Shut off power to the machine.
2. Visually inspect the 220V or 440V wiring going into the electrical panel. Visually verify the
wiring is correct per our wiring diagram. Make sure a strain relief is being used where the
wiring enters the cabinet. Have the customer repair any wiring discrepancies.
3. Clean the machine if needed and remove any remaining grease.
4. Unlock the table, saddle, and ram gib locks.
5. For DPME2 only, use a 10 mm socket to turn the Z-axis ball screw at the top of the column in
order to lower the head until the counterweight is raised off the counterweight support rods.
6. For TRM, DPM, DPM5, Sport B3 & Sport B5, check to ensure that the Z-axis upper way cover
spacers are in place to prevent the way cover from getting caught in the Z-axis counterweight
chain support sprockets.
7. Using the manual hand crank, lower the head until the counterweight is raised off the
counterweight support rods.
8. Remove the two (2) counterweight support rods.
9. Remove the manual Z-axis hand crank. (TRM, DPM, DPM5, Sport B3, Sport B5, DPMS3,
DPMS5 only)
10. Attach (2) wiper brushes to each table tray using (2) M5 X10 button head cap screws
(supplied) per brush. Install (1) table tray on each end of the table (DPM5, SPORT B5,
DPMS5 only). NOTE: Ensure that the tray does not scrape the TURCITE. Check TURCITE for
damage.
11. Mount the pendant to the pendant arm using (4) 1/4-20 x 3/4" socket head cap screws. For
DPME2 only, mount the pendant to the arm using (3) 3/8-16 nuts and lock washer.
12. Make and check all the proper electrical connections from the pendant to the electric box.
See the pendant and electric box wiring diagrams.
13. If applicable, load TRAK sensors.
14. Ensure that the 220/440V and, if applicable, the 110V lines are plugged in. Turn on power to
machine and pendant.
15. Fill all the head oil cups with SAE 30 oil.
16. Lubricate all the way surfaces and the ball screws.
17. Jog the table, saddle, and ram back and forth until the way surfaces are well lubricated. Oil
should be visible on all the way surfaces.
18. Crank the X and Y electronic handwheels to check for functionality.
19. Run the spindle through the high and low gears/speeds and check spindle brakes.
20. Check and use the quill power feed to ensure that it works.
21. Check the level of the machine. The machine should be level to within 0.0005"/10 front to
back and 0.0005"/10 side to side. Even though it is the responsibility of the customer, make
any necessary adjustments.
22. Check to make sure that the E-Stop button is functioning correctly.
23. Perform Service Code 12, Feed Forward Constant. X- and Y-axis values should be between
2 and 8. Z-axis values should be between 10 and 12. This code must be run any time that a
mechanical adjustment or change is made to the machine.
24. Perform Service Code 123 to calibrate the X, Y & Z-axis (quill/ram). Use a 150 mm standard
for all axes except use a .75 mm standard for Z quill.

9
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 25. Perform Service Code 11 to automatically calculate the backlash for the X and Y-axis of dual
feedback machines only (i.e. TRAK sensor or glass scale with a motor encoder).
26. Perform Service Code 127 and 128 to manually calculate the backlash for the X and Y-axis of
single feedback machines only (no glass scale or sensor).
27. Check for positional accuracy and repeatability on the X and Y-axis using the machine’s
relevant test program. Positioning and repeatability values should be within 0.0005”.
28. Perform Service Code 100 in both directions for the X, Y, and Z-axis to verify that the
feedrate shown on the display is at least 180 ipm.
29. Perform Service Code 97, if necessary, to configure the direction of travel for each axis.
30. Where applicable, perform Service Code 124 to calibrate the Z-axis ram (ball screw). You will
need to reinstall the ram manual crank mechanism. Be careful not to jog the Z-axis
while the crank is installed.
31. Install the Z-axis upper way cover. Install the Z-axis lower way cover and its bracket.
32. Install the Y-axis front and rear way covers.
33. If machine has an auxiliary function option, use accessory key on pendant and ensure that
the coolant pump or solenoid for the mister works. The accessory key should be in the ON
position to test coolant pump or solenoid. The control should be in DRO mode. Make sure air
is hooked up to the machine during the test. If the machine has a separate coolant pump
switch mounted on the pendant arm, turn this on and off to test.
34. If the machine has a power drawbar option, check to ensure that the tools load and unload
properly.
35. Cut a Euclid block. Visually inspect the block and make any required machine adjustments.
See Euclid block instructions in Section 2.17.
36. Wipe down the machine prior to leaving.

2.5 Machine Specifications

Specifications DPME2 TRM, DPM, SPORT B3, DPM5, SPORT B5,
DPMS3 DPMS5
Table Size 49” x 9” 50” x 10” 50” x 12”
T-Slots (number x width x pitch) 3 x 16 mm x 64mm 3 x 16 mm x 64 mm 3 x 16 mm x 64 mm
Travel (X, Y, Z axis) 31 x 16 x 23.5” 31 x 17 x 23.5" 40 x 20 x 23.5”
Quill Diameter 86 mm 100 mm 100 mm
Spindle Taper R8 #40 taper #40 taper
Spindle Speed Range Low 60-600 70 – 4200 RPM 70 – 3950 RPM
High 550-5000
Spindle Nose to Table (max part height) 23.5” 23.5” 23.5”
Spindle Center to Column Face 18” 19" 20”
Spindle Motor Power 3 HP 3 HP 5 HP
Voltage 220 V 220/440 V 220/440 V
Phase/Cycle 3-phase/60Hz 3-phase/60 Hz 3-phase/60 Hz
Current (Full load amps) 8.5 FLA 8.5/4.25 FLA 14/7 FLA
Machine Net Weight/Shipping Weight 3200 lbs/3500 lbs 4100 lbs/4400 lbs 4400 lbs/4600 lbs
Maximum Weight of Workpiece 1320 lbs 1320 lbs 1760 lbs

2.6 Maximum Work Capacities

DPME2 TRM, DPM, SPORT B3, DPM5, SPORT B5,
DPMS3 DPMS5
Drilling Mild Steel 1” 1” 1”
Tapping Mild Steel .75” 1” 1”
Milling (metal removal rate/mild 2 inch3/min 3 inch3/min 5 inch3/min
steel)

10
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
Maximum work capacities are dependent on a lot of variables that cannot be controlled by the
machine manufacturer. Each one of the following will have an impact on the above numbers:
speeds, feeds, cutter, cutter sharpness, material, setup, coolant and machine adjustments. The
numbers above assume all conditions are optimal and may be higher or lower depending on
material composition.

2.7 Control Hardware

2.7.1 TRAK AGE & ProtoTRAK MX Controls – TRM & DPM
(DPM5 – AGE only)
• Digital Servo Amplifiers custom designed for ProtoTRAK AGE 2/AGE 3 operation.
• D.C. Servo Motors rated at 280 in-oz. continuous torque for X and Y, and 560 in-oz for Z.
• Ball screws in the table, saddle, and column ensure smooth accurate contours
without backlash.
• Closed-loop Feedback utilizing TRAK Sensors with .0002" underlying resolution. This
is optional for the Sport B3 & B5.
• Modular Design simplifies service and maximizes uptime.
• 115V-60HZ-15 amps.
• Feedrate Override of programmed feedrate and rapid.
• Polycarbonate Sealed Membrane Keypad and Gasket Sealed Control
• Enclosures to lock out contamination.
• 9" CRT for clear presentation of prompts, status information and part graphics.
• Built-in Floppy Disk Storage for program storage.
• RS 232 Port for interface with computers.
• Auxiliary Function to interface with Haas type rotary indexers (DPM)
• Auxiliary Function to control A/C outlet (DPM).
• Auxiliary Function to control Air Solenoid System (spray misters) (DPM).

2.7.2 ProtoTRAK M3 Controls - Sport B3 & B5

• Digital Servo Amplifiers custom designed for ProtoTRAK M3 operation.
• D.C. Servo Motors for the X and Y-axes at 280 in/oz for the B3, and 560 in/oz for the
B5. The Z-axis is rated at 560 in/oz for both the B3 and B5.
• Ball screws in the table, saddle and column ensure smooth accurate contours
without backlash.
• Closed-loop Feedback utilizing .000036” resolution motor encoders.
• Modular Design simplified service and maximizes uptime. 115V-60HZ-15 amps.
• Feedrate Override of programmed feedrate and rapid.
• Polycarbonate Sealed Membrane Keypad and Gasket Sealed Control
• Enclosures to lock out contamination.
• 9" CRT for clear presentation of prompts, status information and part graphics.
• Built-in Floppy Disk Storage for program storage.
• RS 232 Port for interface with computers.
• Auxiliary Function to interface with Haas type rotary indexers (B3 option only).
• Auxiliary Function to control A/C outlet (B3 option only)
• Auxiliary Function to control Air Solenoid System (spray misters, B3 option only).
• Electronic Handwheels for the X and Y axes (B5 only)

2.7.3 ProtoTRAK SM Control - DPMS3 & DPMS5

• 3-axis CNC, 3-axis DRO
• 233 PC-based processor

11
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
• 32 MB of RAM
• D.C. Servo Motors rated at 560 in-oz continuous torque for X, Y and Z-axes
• Precision ground ball screws in the table, saddle and ram to ensure smooth accurate
contours without backlash
• Feedrate override of programmed feedrate and rapid
• Polycarbonate sealed membrane and gasket sealed control enclosure to lock out
contamination
• 10 ½" color LCD for clear presentation of prompts, status information and part
graphics
• RS232 port for interface to computers
• Modular design simplifies service and maximizes uptime
• 64 GB flash drive
• Optional flash expansion slot
• Single floppy disk drive for additional part program storage
• Optional auxiliary function box for control of coolant pump or spray mist coolant,
spindle off and a programmable rotary table or indexer

2.7.4 ProtoTRAK Edge 3 Control – DPME2

• Precision ground ball screws in the table, saddle and ram to ensure smooth accurate
contours without backlash
• Feedrate override of programmed feedrate and rapid
• Polycarbonate sealed membrane and gasket sealed control enclosure to lock out
contamination
• 7.4” LCD for presentation of prompts and status information
• Modular design simplifies service and maximizes uptime
• Single floppy disk drive for additional part program storage
• 3-Axis CNC, 3-Axis DRO: The Edge 3 CNC works like what is commonly referred to
as 2½-axis. 2½-axis means that there is a third axis present (Z-axis), but you
cannot program all three axes to move at the same time. In the ProtoTRAK Edge 3
the Z-axis will always move first, and then X and Y. Therefore you cannot program
any type of part where you would need to move the Z-axis at the same time as X or
Y.
• The D.C. Servo Motors for the X and Y-axis are rated at 280 in-oz. maximum
continuous torque. The Z-axis is rated at 560 in-oz. maximum continuous torque.

12
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
Figure 2-3 TRAK & Sport Bed Mills Component Identification

13
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 TRAK & Sport Bed Mills Component Identification
Item Description Part Number *
TRM DPM DPM5 Sport Sport DPMS3 DPMS5 DPME2
B3 B5
1 Spindle 16501 16501 20820 16501 20820 20820 20820 23585***
Motor
2 MX2 MX3 AGE3 M3 M3 SM SM EDGE
15814 16274 20180-1 20347-2 20347-4 22328-3 22328-3 23688-
Pendant AGE2 AGE3 20347-3 USA
20180 20180-1 (B3 with
sensors)
3 Y-Axis 15616 15616 20082-1 15616 15616 15616 15616 15616
Handwheel **
4 X-Axis 15616 15616 20082-1 15616 15616 15616 15616 15616
Handwheel **
5 Lube Pump L001L 21688-4 21157-1 21688-4 21157-1 21157-1 21157-1 21157-2
L001R
X, Y or Z 20276=x 20276=x 21685= 20276=x 21685= 23198= 23198 20296=
Motor 20296=y 20296=y x, y 20296=y x, y x, y, z = x, y, z x, y
20328=z 20328=z 20328=z 20238=z 23198=z

* All replacement part numbers, with exception to lube pumps that are sold as
new, have a suffix “R.” For example, 23585-1R and 20296R
** 20082-1 = Electric Handwheel
***Programmable spindle motor

14
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 Figure 2-4 TRAK & Sport Bed Mill Rear View
Item Description Part Number *
TRM DPM DPM5 Sport B3 DPMS3/S5 DPM
Sport B5 E2
1 Electrical Box/ 20065- 17009- 21800- 20676 220 = 20676-1 23630
Relay Module 220 220 220 (220V & 440V) 440 = 20676 (220V
20065- 17009- 21800- 220V-20676-1 only)
440 440 440 B5 Only

2 Cable Breakout Box N/A N/A N/A 20290 23050 N/A

3 Cable Breakout Box N/A N/A N/A 20290-1 23050-1 N/A
with AUX Functions
* All replacement part numbers have a suffix “R.”

15
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 For example, 20065-220R and 20676-1R

2.8 Lifting and/or Moving the Machine

CAUTION!
The TRAK & Sport bed milling machines weigh between 3200 and 4400 lbs. Proper equipment of
sufficient capacity must be used when lifting and/or moving the machine.

Method 1 (see Figure 2-5):

1. Insert a steel bar 1.0" dia x 36" long through the rear side holes of the bed (under column).
2. Use a steel cable (with protective sleeving) min. 3/4" dia. or a 3 ton sling.
3. Use cardboard pieces or other suitable protective sheets on both sides of the machine to
prevent scratching.
4. Remove the 4 nuts and screws holding the machine to the wood skid.
5. Lift the machine (the front side of the machine should be lower than the back side).
6. Insert the 6 screws for leveling pads in their place in the bed. 4 screws for DPME2.
7. Place the machine in its location (see floor plan and bed footprint drawing) carefully
positioning each leveling pad under each leveling screw.
8. Remove the lifting cable or sling, the steel bar and all protective cardboard.

Figure 2-5
Lifting the Machine
Method 1

16
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
Method 2 (see Figure 2-6):
1. Insert 2 steel bars 1" dia x 36" long through both sides in the existing holes in the
machine base (front and back).
2. Position 4 (two each side) wood vee blocks under the steel bars and over a suitable lift
truck.
3. Lift the machine up (somewhat tilted towards the front) 4-6" from the ground and move
it to its floor plan position.

WARNING!
The lift truck must have sufficient lifting capacity and be equipped with suitably long forks.

4. Insert the 6 screws for the leveling pads in their place in the bed.
5. Place the machine in its location (see floor plan bed/footprint) carefully positioning each
leveling pad under each leveling screw.

Figure 2-6
Lifting the Machine
Method 2

17
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 2.9 Releasing the Head Counterweight Supports
In order to move (raise or lower) the spindle head/ram it is first necessary to remove the 2 steel
rods (with flanges) inserted through the holes in the column. These rods support the
counterweight during shipping to prevent damage to the counterweight chains and sprockets.

1. Release ram gib locks.

2. DPME2 – Lower the head slowly with a 10mm socket on the top end of the Z-axis ball
screw until the chain between the ram and the counterweight is tight.
TRM, DPM, DPM5, Sport B3, Sport B5, DPMS3, DPMS5 - Lower the head slowly with the
ram crank until the chain between the ram and counterweight is tight.
3. Lower a little further until the 2 support steel rods are loose. Remove the 2 steel rods
and store them for future machine moves or transportation.
4. (DPM, DPM5, DPMS3 & DPMS5 only) Remove the panel on the bottom rear of the bed. .
Verify that the lower end of the counterbalance rod guide at the bottom of the column is
attached using the (2) socket-head cap screws supplied. Replace the panel.
5. Do not continue to move the ram until all ways have been cleaned.

CAUTION!
Do not remove the steel rods unless they are loose.

2.10 Cleaning
1. Remove rust protective coating from the machine before moving any slideways (table,
saddle, ram, etc.).
2. The coating is best removed with clean, dry rags. Do not use a cleaning solution that
may damage the rubber way scrapers, plastic parts, or paint.
WARNING!
Do not use gasoline or other flammable cleaning agents for cleaning the machine.
3. It may be necessary to move back and forward, left and right, and up and down the
table, saddle and the ram. Always release the clamp levers (two in front of the
table, one underneath the saddle on each side, and two on the ram on the
right side of the column) before attempting to move the above parts.

CAUTION!
Never move any of the above parts over ways that were not previously cleaned.
Serious damage to the TURCITE surface of slideways can occur.
4. Be certain the table, saddle, ram, and spindle move freely and smoothly over their entire
length.

2.11 Leveling: Leveling Tolerance for TRAK & Sport Bed Mills
is .0005”/10”
1. Set the machine on its 6 leveling pads on a solid, level floor prepared in accordance with
the state and local rules for machine tool installation. The DPME2 only uses 4 leveling
screws.

18
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
2. Put one or two precision Spirit Levels or Electronic Levels in the center of the table in the
positions illustrated in Figure 2-7.
3. Adjust the 4 corner leveling screws on their pads until the machine is level to .0005 in/10
in. For the TRM, DPM, DPM5, Sport B3, Sport B5, DPMS3, and DPMS5, snug the 2
middle leveling screws being careful to not affect the level.
4. If the machine must be anchored to the floor, follow the general instruction for installing
machine tools and use for leveling any well-known methods: shims, etc.).
5. If the machine must be installed on vibration mounts/pads (rubber, commercially
available leveling and vibration mounts, etc.) follow the instructions delivered with the
mounts/pads, ordering them to satisfy the load of the machine and the maximum weight
of the workpiece (6,000 lb.).
6. When machine is correctly level, lock the adjusting screws in place with their hex nuts.

Figure 2-7 Placement of Levels

I00138

Figure 2-8 Leveling Screws

19
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
2.12 Electrical Connection
The TRAK & Sport Bed Mills can be configured for 220 or 440-volt 3-phase electricity with
exception to the DPME2, which is only configured for 220 volt electricity. These machines also
require a 110V power source to power the control.

DANGER!
Be certain that 200-volt electricity (typical range 208 – 240V) is used only with a machine labeled
220 volts at the motor and at the electrics box on the back of the column.
Be certain that 400-volt electricity (typical range 415 - 460V) is used only with a machine labeled
440 volts at the motor and at the electrics box on the back of the column.

DANGER!
The 220 or 440-volt line must originate from a dedicated and independent fused box with a
manual shut-off lever. It is the responsibility of the purchaser to supply a wired box that meets
all local codes and regulations.

Incoming 220 or 440 power connects to the machine through the electrical box located on the
back of the column. The power cable enters the black box through a hole on the top of the box.

DANGER!
Only a qualified electrician should wire the 220 or 440-volt 3-phase electricity.

To convert a DPMS3 machine from 220 to 440 volt power or vice versa 3 things must happen:
spindle motor must be rewired, overload relay must be set to 8.5 amps for 220 V and 4.25 for
440 volts and the voltage stickers on the electric’s box must be replaced.

To convert a DPMS5 machine from 220 to 440 volt power 3 things must happen: spindle motor
must be rewired, overload relay must be replaced and set to 14 amps for 220 V and 7 for 440
volts and the voltage stickers on the electric’s box must be replaced.

See Section 5-30 and 5-31 for diagrams on wiring the spindle motor.

Southwestern Industries recommends the machine be earth grounded by driving a copper rod
into the ground. It is the responsibility of the customer to install this rod.

20
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Part number reference table for TRAK & Sport Bed Mill Pendants
Description Part Number *

TRM DPM DPM5 Sport B3 Sport DPMS3 DPMS5 DPME2

B5
MX2 MX3 AGE3 M3 M3 SM SM EDGE
15814 16274 20180-1 20347-2 20347-4 22328-3 22328-3 23688-USA
Pendant P/N (without
sensors)
AGE2 AGE3 20347-3
20180 20180-1 (B3 with
sensors)

Part number reference table for wiring the TRAK & Sport Bed
Mills

Description Part Number *

TRM DPM DPM5 Sport B3 Sport B5, DPME2
DPMS3/S5
Electrical Box/ 20065-220 17009-220 21800-220 20676 220 = 20676-1 23630
Relay Module 20065-440 17009-440 21800-440 (220V & 440V) 440 = 20676 (220V
only)
Relay - Overload 220V = Z00- N/A N/A 220V=23438-1 220V=23438-1 N/A
10 440V=23438 440V=23438
440V = Z00-6
Relay Module N/A 20157-220 N/A N/A N/A N/A
with transformer 20157-440
option
Contactor (Qty= DILOOM N/A
2) (Reverse or 94-xxx or older
Forward) only

* All replacement part numbers, with exception to L001 pumps, have a

suffix “R.”
For example, 17009-220R and 23438-1R

21
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
2.12.1 Cable Connections for TRM, DPM & DPM5 Pendant

Figure 2-9
Pendant Drawer – AGE 2/3 & MX2/3
TRM, DPM & DPM5

22
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-10
Computer Cabinet – AGE3 & MX3 Connections
DPM & DPM5

23
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-11 AGE2 / MX2 Computer Cabinet – TRM

24
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 2

Figure 2-12 TRM Wiring (P/N 16042) for 1995 and earlier

Z00-10 = 220V – Motor Overload Relay

1
Z00-6 = 440 V – Motor Overload Relay

2 DILOOM (220/440) – Motor Contactor

25
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 2-13
Electric Box Connections – DPM &
DPM5

26
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-14 Wiring Diagram – DPM & DPM5
(continued on following page)

27
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 2-14 Wiring Diagram – DPM & DPM5
(continued from previous page)
28
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 2.12.2 Pendant and Wiring Diagrams for Sport B3 & B5 – M3

Figure 2-15 M3 Pendant Display Basic Configuration

Sport B3 & B5
29
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-16 -- 20676 / 20676-1
Wiring the Sport B3 & Sport B5

Part Number Description

220V & 440V = 20676 Electrical Box
220V & 440V = 23438-3 Overload
23436 Contactor (Qty = 2) (Reverse or Forward)

30
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-17 – Sport B3 & B5 – 20676 / 20676-1
Electric Box Connections

31
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-18
Schematic Standard Electric Box – Sport B3 & B5 –
20676 / 20676-1

32
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 2.12.3 Pendant and Wiring Diagrams for DPMS3 & DPMS5

Figure 2-19 Pendant Cable Connections – SM

Left Side – DPM S3/S5

Figure 2-20 Pendant – SM

Right Side – DPMS3/S5

33
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-21
Wiring the DPMS3 & DPMS5 – 20676 / 20676-1

34
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
2.12.4 Pendant and Wiring Diagrams for DPME2 – EDGE 3

Figure 2-22
EDGE 3 Pendant Rear – DPME2 – 23689 (USA)

35
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-23 Electrical Box Without Transformer – DPME2

Item # SWI P/N Description

1 22127-DPME2 AC DRIVE-PROGRAMMED DPME2 3 HP
2 22961 RELAY-POWER-115V DPST
3 22595 RELAY-POWER-115V SPDT
4 22890-200 RESISTOR - 200W - 60Ω

i01306

36
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 2-24 Electrical Schematic – DPME2
2.12.5 Phase Converters
For those machines that will be run with a phase converter, it is recommended that it is a
rotary type rather than a static phase converters. Rotary phase converters allow for
varying loads in the system. The electrical load on the machine will vary based on the
type of cut taken. Static phase converters can only be used on machines with a non-
varying load. The following chart depicts the phase converter ratings per machine
model:

Machine Model Minimum Phase Converter Rating

TRM 5 KVA
DPM 5 KVA
DPM5 7 KVA
Sport B3 5 KVA
Sport B5 7 KVA
DPMS3 5 KVA
DPMS5 7 KVA
DPME2 5 KVA

37
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
2.13 Air Connection – Optional for DPME2, DPMS3, & DPMS5
The TRAK & Sport Bed milling machines have an air hookup in the rear of the machine if the
machine has a power drawbar or auxiliary function option.

The drawbar option includes an air regulator, air manifold and an oiler. The auxiliary option
includes an air regulator, air manifold and a solenoid. If both options are included on the same
machine, a regulator, manifold, oiler and solenoid will be included. The air fitting is ¼” NPT. An
additional air line port is on the manifold to be used for an optional mister. Remove the plug to
gain access to this port.

The air regulator is set to 90 PSI at the factory for the power drawbar unit and solenoid. See
Section 5.1.8 for more information on the power drawbar unit. The air comes in through the
manifold and passes through the air regulator. The regulator branches into two components--an
oiler for the power drawbar unit and an air solenoid. The solenoid is used for a misting system
that the user may install later on this machine. The mister air hose can be plugged into the ¼”
quick disconnect air fitting on the solenoid.

2.14 Mounting the Display Pendant

The display pendants for the ProtoTRAK M3, SM & MX and the TRAK AGE mount to the pendant
arm with four 1/4-20 x ¾ SHCS that are shipped screwed into the left side of the display. The
ProtoTRAK Edge 3 display pendant mounts the same way except with 3 studs. The Edge 3
requires (3) 3/8-16 nuts and washers to fasten the pendant to the arm. For all models, a
locating screw on the pendant arm helps align the pendant with the mounting holes.

CAUTION!
The locating screw in the arm is used for positioning. Hold the pendant firmly until the screws
are fastened.

If the pendant arm rotates too freely, remove the painted cap on the bracket attached to the
column and tighten the hex nut to adjust it. Replace the cap.

2.15 Cable Interconnections

All cable interconnections are made at the factory except for those connecting to the pendant
display.

With the main power to the machine turned off, plug in the connectors that are bundled on the
pendant arm. Each cable mates to only one connector on the pendant display back panel. Use
the label on the pendant to match the connectors with the correct port.

Ensure that there is sufficient slack in the cables for the pendant to rotate about the pendant
arm. The worst case is when the pendant is all the way forward toward the operator. The
following drawing describes all of the cable connections to the pendant.

For DPMS3/S5 only: Ensure that an option key is plugged into the option key port of the
pendant. This key activates any converters or options ordered. The part # for this key is
22648-5. The key must be programmed according to the type of machine it is on and the
options ordered.

38
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 The Machine ID port must have a key, or the machine may not run.

CAUTION!
Ensure that the main power is turned off on the back of the electrical cabinet before plugging in
the cables.

Part Number Reference Table for TRAK & SPORT Cable Connections

Description Part Number *

TRM DPM DPM5 Sport Sport DPMS3 DPMS5 DPME2
B3 B5
Electrical Box/ 20065- 17009- 21800- 20676 20676-1 = 220 23630
Relay Module 220/440 220/440 220/440 20676 = 440 220V
Cable N/A N/A N/A N/A N/A 21856 21856 21856
Assembly 23050 23050
Cable N/A N/A N/A N/A N/A 23050-1 23050-1 N/A
Breakout Box
(-1 with AuX)
Option Key N/A N/A N/A N/A N/A 22648-5 22648-5 N/A
Machine ID N/A N/A N/A N/A N/A 22758- 22758- N/A
Key SDPM3 SDPM5
MX2 MX3 AGE3 M3 M3 SM SM EDGE
15814 16274 20180-1 20347-2 20347-4 22328-3 22328-3 23688-
Pendant P/N (without USA
(with control sensors)
model) AGE2 AGE3 20347-3
20180 20180-1 (B3 with
sensors)

* All replacement part numbers have a suffix “R.”

For example, 20065-220R, 20065-440R and 22758-SDPM3R

See Figures 2-25 – 2-30 for cable diagrams for each machine model

39
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-25 Cable Interconnections – TRM / MX2 –
95-xxx and earlier

40
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-26 Cable Interconnection – DPM & DPM5

41
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-27
Cable Interconnections – Sport B3

42
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-28 Cable Interconnections – Sport B5

43
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 2-29 Cable Connection Diagram –
DPMS3/S5
44
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-30 Cable Connection Diagram – DPME2

45
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
2.16 Lubrication
2.16.1 Way Lubrication
2.16.1.1.1 DPM, DPM5, Sport B5, DPMS3, DPMS5 & DPME2
The auto lube system provides centralized automatic lubrication for the ways
and ballscrews. The lube pumps 2-liter reservoir is serviced with Mobil Vactra Oil No. 2
or equivalent. The pump is factory set to pump oil for 15 seconds for every 60 minutes
of spindle time. There is an internal memory on the pump so that the
pump will not reset every time the spindle is turned off.

The pumping output can be regulated electronically to control the pause time between
pumping cycles, and the duration of the pumping cycle. The following describes the
buttons used to program the lube pump. In order to modify any of the settings the
spindle must be on.

The pump has an alarm that will sound if any of the following problems arise:
• Oil line breakage
• Oil filter blockage
• Bad motor
• Low oil pressure
• No oil in tank

INT (Interval) - this button programs the interval between pumping cycles. Each
press of the button increases the interval by one minute.
DIS (Discharge) - this button programs the amount of time the pump will discharge each
pumping cycle. Each press of the button increases the discharge time
by one minute.
FEED - this button is used to manually feed the ways and ballscrews.
RST - this button tells the pump to discharge for the time programmed.

Factory Default Values

Interval Time - 60 min.
Discharge Time - 15 sec
Discharge Pressure - Approximately 100 - 150psi
To adjust the amount of Discharge Pressure displayed on the lube pump gauge, loosen
the jam nut and turn the adjustment screw located on the top right side of the lube
pump while the lube pump is activated.

At the beginning of each day, check the oil level in the Auto Lube system. If low, fill with
Mobil Vactra Oil No. 2 or equivalent.

CAUTION!
Failure to manually activate the pump at the beginning of each day, or allowing the Auto Lube to
run dry may cause severe damage to the TRAK & Sport Bed Mills way surfaces and ball screws.

2.16.1.2 Manual Lubrication - TRM

The TRAK TRM X, Y, Z way surfaces and ball screws are lubricated manually with the
lubrication pumps located on the right side of the bed and the left side of the ram. Pull

46
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 each handle fully and release 4 to 6 times at the beginning of each shift, and once every
four hours of operation thereafter.

At the beginning of each day, check the oil level in each pump. If low, fill with SAE 30 or
30W oil or Mobil Vectra #2.

Every six months of operation, remove the vertical column way covers and apply a liberal
coating of Mobile Grease-MP, or equivalent, to the ACME screw.
2.16.2 Head Lubrication – ALL TRAK & Sport Bed Mills
Once Each Week:
1. Fill the oil cup on the front of the head with SAE 30 or 30 W oil. This oil
lubricates the Hi/Lo range shifter.

2. Fill the ball oiler located in the front lower right corner of the speed changer
housing. This oil lubricates the speed changer shaft.

3. Extend the quill fully and apply a coating of SAE 30 or 30W oil to the outside
diameter of the quill.

Every Four Months:

Apply a good grade of general-purpose grease through the grease fittings on the back of
the head and on the left side of the head. This grease lubricates the Low range gear set
and the feed change gears respectively. Also lubricate vari-disk on spindle motor by
means of grease fitting on motor shaft.

Every Four Months (DPMS5 X Handwheel Drive Mechanism):

Remove X handwheel drive cover and apply a general-purpose grease to the drive gears.
See Section 5, Figure 5-17 for an illustration

Every Six Months (DPMS3):

Remove lower cover under spindle motor and apply general-purpose grease to the fitting
on the spindle motor shaft. You must set the RPM range on the head such that grease
enters the vari-disk cavity. Apply two pumps of grease to adequately grease the vari-
disks. In high gear set the RPM to between 975 and 1440 RPM. In low gear set the
RPM to between 115 and 165 RPM.

Note: Due to the design of the vari-disk keyway, the motor shaft on the DPMS5 does not
need to be greased.

47
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
2.17 ProtoTRAK Euclid Block Procedure- TRAK & Sport Bed
Mills
The test part should be machined at the completion of the installation.

The material for the Euclid block test part is found in the toolbox.

• Material Specification: Aluminum, 6061-T6 or T4

• Blank Size: (minimum dimensions) 3 x 3 x 1”, provided in tool box
• Tool: .750 end mill, 2 flute, high speed steel, sharp
• Coolant: Flood coolant, Cool-Tool or Kerosene

1. Mount vise and indicate the back jaw parallel to the table within .0005”.
2. Clamp material in vice with a minimum of .800” above the vise jaws.
3. Load in the Euclid block program from the ProtoTRAK SM (or ProtoTRAK Edge 3) flash
drive. For SM, the part number is euclid.PT4, which is found under the PT4 folder
followed by the SWI TEST PROGRAMS folder. For PT3, the part number is
99999999.MX3 (or 99999999.MX2), which is located on your parts disk.
3. Use an edge finder to set Absolute 0 on X and Y. Absolute zero is the front left corner of
the block as viewed from in front of the machine.
4. Load the .750 end mill and set Z Absolute 0 at the top of the part, and set Z reference
positions in the SET UP mode. Set Z-retract a few inches above the part.
5. Begin to run the program. The part will be machined in the following sequence:
6. After the program run, the program will locate to the following position.
• X = 1.318
• Y = 1.318

Event(s) Description Depth of

# Cut
1 circle pocket – cuts middle circle -0.250”
2 circle frame – cuts outer 1.830 diameter circle -0.250”
3 circle frame – cuts material from corners -0.250”
remaining on Euclid block
4 roughs material in upper right-hand corner -0.500”
5-12 cuts triangle on Euclid block -0.500”
13 rectangular frame – cuts outer 2.750” rectangle -0.7500”

7. Mount a dial indicator in the quill and check the circles.

8. Check the runout of the sides of the square frame.
9. Inspect the machined surfaces for smoothness.

48
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 2-31
Euclid Block

49
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 3.0 Troubleshooting by Symptom
Use this section to begin the process of resolving a service problem. Each symptom type is
described in a few words and then more fully described in an explanatory paragraph. Following
this is a chart that directs in the most logical steps.

3.1 Problems Relating To Machining Results

3.1.1 Poor Finish
The part finish is marred with scallops or is very rough.

Perform the following Service Codes and document values:

• Code 33 Software Identification. This is needed if you call SWI Customer Service
• Code 11 Measures backlash in the system (Only used on Dual-feedback systems)
• Code 12 Feed Forward Constant
• Code 127 Measures backlash in the system (Only used on Single-feedback systems)
• Code 128 Enter backlash compensation (Only used on Single-feedback systems)

Possible Cause Check This

Too much backlash entered for Code Verify nothing is mechanically loose and the backlash
128 or calculated with Code 11. values are not higher than what physically is in the
system.
Machine Tool & Setup problem Check for any looseness in the setup (Tool, Tool holder,
Part, Vise, or Fixture). Check the condition and type of
cutter being used, type of material, RPM and Feedrate,
etc. See Machine Tool & Setup Section 4.1
Table, Saddle, or Ram Locks are locked Make sure the Table, Saddle, and Ram Locks are
unlocked. Never use gib locks with a CNC machine.
Inadequate or no Lubrication to Make sure all the Way surfaces are getting proper
Ballscrews and Way surfaces lubrication. If not, check to make sure that the lube pump
is functioning properly. Also check for any pinched or
blocked oil lines. See Lubrication Section 4.1.3
X, Y, and Z-axis Gibs are not adjusted Check the adjustment of the X, Y, and Z-axis Gibs. See X,
properly Y, and Z-axis Gib Adjustments in Section 5.2.1.
X & Y-axis Drive Trains are loose Check Repeatability using the Repeatability and Positional
Accuracy procedure. Step by step, carefully inspect the
Drive Train for any looseness. It may be necessary to
disassemble and then reassemble the Drive Train. See
Mechanical Drive Train (X, Y) Section 4.2
Way surfaces are pocked, scarred, or Visually check the condition of all the Way surfaces. For
excessively worn machines that may have excessively worn Way surfaces
you may need to adjust the Gibs in this area. This will
affect performance when using the machine outside of
this area. Check lubrication to affected areas.

3.1.2 Circles Out of Round

Circles are not round within 0.002” TIR over 3.0” DIA. This is best measured by placing
a dial indicator in the quill and sweeping around the part.

50
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Note: The typical slideway-milling machine is not capable of achieving more precise
results although careful adjustments to a new milling machine have produced better
results. If more precise circles are required, then it is recommended to use a precision
boring head/boring bar.

Perform the following Service Codes and document values:

• Code 33 Software Identification. This is needed if you call SWI Customer Service
• Code 11 Measures backlash in the system (Only used on Dual-feedback systems)
• Code 12 Feed Forward Constant
• Code 127 Measures backlash in the system (Only used on Single-feedback systems)
• Code 128 Enter backlash compensation

Possible Cause Check This

Torque values on X and Y-axis are too Make sure torque is lower than 20 in-lbs. Normal values for a
high. machine that is aligned and adjusted properly should be
between 10 and 15 in-lbs. Make sure torque is consistent across
axis travel.
Machine Tool and Setup problem Check for any looseness in the setup (Tool, Tool holder, Part,
Vise, or Fixture). See Machine Tool & Setup - Section 4.1
Machine not level Verify that the machine is level to specification.
Head is not Trammed Verify that the Head is Trammed to specification. See Tramming
the Head
X, Y, and Z-axis Gibs are not adjusted Check the adjustment of the X, Y, and Z-axis Gibs using the X,
properly Y, and Z-axis Gib adjustment procedures.
Calibration or Backlash problem Recalibrate the machine. Reset the Backlash. Check
Repeatability and Positional Accuracy. See Calibration &
Backlash Constants – Section 5.2.2
Where applicable, TRAK Sensor or Glass Make sure that the Sensor or Glass Scale is installed correctly
Scale problem according to the Sensor or Glass Scale Installation procedures.
Check for any loose brackets or misalignment etc. Also, check to
make sure the Sensor or Glass Scale assemblies are functioning
correctly. See TRAK Sensors or Glass Scales Sections 4.6 & 4.7.
X & Y-axis Drive Trains are loose Check Repeatability using the Repeatability and Positional
Accuracy procedure. Step by step, carefully inspect the Drive
Train for any looseness. It may be necessary to disassemble and
then reassemble the Drive Train. See Mechanical Drive Train
(X, Y) Section 4.2
Head Bolts are loose Verify that all the head bolts are tight.

3.1.3 Taper Cut on a Programmed Straight Line Move

An unwanted tapered cut occurs, when the machine is programmed to move in a straight
line along either the X or Y-axis. The DRO shows motion of a few thousandths of an inch
in the axis that is not supposed to be moving.

Explanation: For straight line cuts along the X or Y-axis, the control is designed to lock
the motor of the axis that is not moving. A taper is created when there is play in the
system. The force of the tool shoves the table or saddle out of position.

51
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 The system will respond to being pushed out of position by making an adjustment at the
end of the move.
An unwanted tapered cut is the result of looseness in the system.

Perform the following Service Codes and document values:

• Code 33 Software Identification. This is needed if you call SWI Customer Service
• Code 11 Measure's the backlash in the system. (Only used on machines with Dual-
feedback systems)
• Code 12 Feed Forward Constant
• Code 127 Measure's the backlash in the system. Only used on machines with
Single-feedback
• Code 128 Enter backlash compensation

Possible Cause Check This

Machine Tool & Setup problem Check for any looseness in the setup (Tool, Tool holder, Part,
Vise, or Fixture). See Machine Tool & Setup Section 4.1
X, Y, and Z-axis Gibs are loose Check the adjustment of the X, Y, and Z-axis Gibs using the X,
Y, and Z-axis Gib adjustment procedures. See Section 5.2.1
X and Y-axis Drive Trains are loose Check Repeatability using the Repeatability and Positional
Accuracy procedure. Step by step, carefully inspect the Drive
Train for any looseness. It may be necessary to disassemble
and then reassemble the Drive Train. See Mechanical Drive
Train (X, Y) Section 4.2

3.1.4 Parts Have Incorrect Dimensions

Parts are being machined with dimensions that are different than those programmed.
Typical accuracy expectations should be:
• Circles: 0.002” TIR over 3.00” DIA
• Positional Accuracy: 0.0005"
• Repeatability: 0.0005"

Note: The typical slideway-milling machine is not capable of achieving more precise
results although careful adjustments to a new milling machine have produced better
results.

Furthermore, the system should be expected to repeat within the resolution of the
displayed DRO numbers of 0.0005”.
Perform the following Service Code:
• Code 33 Software Identification. This is needed if you call SWI Customer Service
• Code 123 Calibration
• Code 11 Measure's the backlash in the system. (Only used on machines with Dual-
feedback systems)
• Code 12 Feed Forward Constant
• Code 127 Measure's the backlash in the system. Only used on machines with
Single-feedback
• Code 128 Enter backlash compensation

52
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 3.1.4.1 Every Part Has the Same Error
Possible Cause Check This
Machine Tool & Setup problem See Machine Tool & Setup Section 4.1
Programming Error In the program, look for common errors in programming
such as transposing numbers, tool diameters, and
pressing INC SET when ABS SET is meant. This is
especially suspected if the dimensional errors are larger
than a few thousandths. See the Controls Programming,
Operations and Care manual.
Configuration file that contains calibra- Verify configuration file (Code 313) does not read default
tion file and backlash constants has values. Load saved configuration file from floppy disk in
been erased or corrupted. electrics cabinet with Code 141.
Calibration or Backlash problem Recalibrate the machine. Reset the Backlash. Check
Repeatability and Positional Accuracy. See Calibration &
Backlash Constants – Section 5.2.2

3.1.4.2 The Dimensional Errors Are Random or Accumulate in Size

Over the Part Program Run
Possible Cause Check This
Machine Tool & Setup problem See Machine Tool & Setup Section 4.1
Where applicable, TRAK Sensor or Glass Make sure that the Sensor or Glass Scale is installed
Scale problem correctly according to the Sensor or Glass Scale
Installation procedures. Check for any loose brackets or
misalignment etc. Also, check to make sure the Sensor or
Glass Scale assemblies are functioning correctly. See
TRAK Sensors or Glass Scales Sections 4.6 & 4.7
X and Y-axis Drive Trains are loose Check Repeatability using the Repeatability and Positional
Accuracy procedure. Step by step, carefully inspect the
Drive Train for any looseness. It may be necessary to
disassemble and then reassemble the Drive Train. See
Mechanical Drive Train (X, Y) Section 4.2

3.2 Problems Regarding the Motion of the Machine

3.2.1 Run Away Axis
The axis makes an unwanted move at rapid speed in one direction and faults out. This is
usually caused by an encoder signal being interrupted.
Perform the following Service Codes:
• Code 33 Software Identification. This is needed if you call SWI Customer Service
• Code 100 Axis open loop test. Used to check the maximum feedrate of an axis and
if the encoders are counting properly

53
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Possible Cause Check This
Where applicable, Sensors or Glass Reverse directions with codes 321 and 322 – SM
Scales are counting in opposite direction Code 97 for M, A.G.E., MX, Edge Control
of motor encoder
The home positions or tools are not set See the Controls Programming, Operations and Care
correctly manual.
Where applicable, Sensor or Glass Scale See TRAK Sensors or Glass Scales diagnostic
is not reading Section 4.6 or 4.7
Bad Motor Encoder See Motor Diagnostics Section 4.4

3.2.2 Slow Down Axis

The axis slows down and moves at a feedrate that is lower than rapid or than the
programmed feedrate.
Perform the following Service Codes:
• Code 33 Software Identification. This is needed if you call SWI Customer Service
• Code 100 Axis open loop test. Used to check the maximum feedrate of an axis and
if the encoders are counting
• Code 129 Set's the maximum allowable arc accuracy error. This applies to arcs only

Possible Cause Check This

The maximum allowable Arc Accuracy is This value will only slow down the machine during arc moves.
set too low. The factory default is set at 0.001". Perform Code 129 to
check or change this value. See Service Codes – Section 4.9
Incoming AC voltage is inadequate Perform Code 100. See Service Codes – Section 4.9 and
Electrical Section 4.8
Table, Saddle, or Ram Locks are locked Make sure the Table, Saddle, and Ram Locks are unlocked.
Inadequate or no Lubrication to Make sure all the Way surfaces are getting proper lubrication.
Ballscrews and Way surfaces If not, check to make sure that the lube pump is functioning
properly. Also check for any pinched or blocked oil lines. See
Lubrication Section 4.1.3
X, Y, and Z-axis Gibs are not adjusted Check the adjustment of the X, Y, and Z-axis Gibs using the
properly X, Y, and Z-axis Gib adjustment procedures.
Binding in the Drive Train Check Repeatability using the Repeatability and Positional
Accuracy procedure. Check the torque reading of the Drive
Train. Step by step, carefully inspect the Drive Train for any
binding. It may be necessary to disassemble and then
reassemble the Drive Train. See Mechanical Drive Train (X, Y)
Section 4.2
Servo Drive failure See Servo Driver Section 4.5
Motor failure See Motor Diagnostics – Section 4.4

3.2.3 Axis Will Not Jog

The system powers up but will not respond to the jog command.
Perform the following Service Codes and procedures:
• Code 33 Software Identification. This is needed if you call SWI Customer Service
• Code 100 Axis open loop test. Used to check the maximum feedrate of an axis and
if the encoders are counting

54
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Possible Cause Check This
Improper Boot-up Shut down the system and wait 10 seconds before rebooting
E-Stop is pressed in Check E-Stop. Especially if both axes will not jog
Servo Drive failure Especially, if only one axis will not jog;
See Servo Driver Section 4.5
Shorted motor See Motor Diagnostics Section 4.4
Poor cable or wiring connections See Electrical Connection Section 2.12
Computer/Pendant failed See Computer/Pendant Diagnostics Section 4.3

3.2.4 Axis Motor Motion is not Smooth

While under motor power, the motion is not smooth. The motion appears to be "rough" or jerky”.
Perform the following Service Codes and procedures:
• Code 33 Software Identification. This is needed if you call SWI Customer Service
• Code 11 Measure's the backlash in the system. (Only used on machines with Dual-
feedback systems)
• Code 12 Feed Forward Constant. High feed forward constants will cause an
unstable servo system
• Code 127 Measure's the backlash in the system. Only used on machines with
Single-feedback
• Code 128 Enter backlash compensation
• Code 100 Axis open loop test. Used to check the maximum feedrate of an axis and
if the encoders are counting

Possible Cause Check This

X, Y, and Z-axis Gibs are not adjusted Check the adjustment of the X, Y, and Z-axis Gibs using
properly the X, Y, and Z-axis Gib adjustment procedures.
Where applicable, TRAK Sensor or Glass Make sure that the Sensor or Glass Scale is installed
Scale problem correctly according to the Sensor or Glass Scale
Installation procedures. Check for any loose brackets or
misalignment etc. Also, check to make sure the Sensor or
Glass Scale assemblies are functioning correctly. See
TRAK Sensors or Glass Scales Section 4.6 & 4.7
Calibration or Backlash problem Recalibrate the machine. Reset the Backlash. Check
Repeatability and Positional Accuracy. See Calibration &
Backlash Constants – Section 5.2.2
Binding in the Drive Train Check Repeatability using the Repeatability and Positional
Accuracy procedure. Check the torque reading of the
Drive Train. Step by step, carefully inspect the Drive
Train for any binding. It may be necessary to
disassemble and then reassemble the Drive Train. See
Mechanical Drive Train (X, Y) Section 4.2

3.2.5 Vibration in Motion

While axis is moving there is vibration or noise coming from the X or Y-axis.

Perform the following Service Codes and procedures:

• Code 11 Measure's the backlash in the system. (Only used on machines with Dual
Feedback systems)

55
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 • Code 12 Feed Forward Constant. High feed forward constants will cause an
unstable servo system
• Code 127 Measure's the backlash in the system. Only used on machines with Single-
feedback
• Code 128 Enter backlash compensation
• Code 123 Calibrate

Possible Cause Check This

Too much backlash entered in Code 128 Recheck the machine’s backlash.
or Code 11.
Inadequate or no Lubrication to Make sure all the Way surfaces are getting proper
Ballscrews and Way surfaces lubrication. If not, check to make sure that the lube pump
is functioning properly. Also check for any pinched or
blocked oil lines. See Lubrication Section 4.1.3
X, Y, and Z-axis Gibs are not adjusted Check the adjustment of the X, Y, and Z-axis Gibs using
properly the X, Y, and Z-axis Gib adjustment procedures.
Gibs not making good contact. Pull gibs out and mark with a blue die to check where the
gibs are making contact. It is recommended that the gibs
uniformly contact at least 80% of the surface.
Binding or looseness in the Drive Train Check Repeatability using the Repeatability and Positional
Accuracy procedure. Check the torque reading of the
Drive Train. Step by step, carefully inspect the Drive Train
for any binding or looseness. It may be necessary to
disassemble and then reassemble the Drive Train. See
Mechanical Drive Train (X, Y) Section 4.2
Axis Motor belt too tight. Loosen belt.
Misalignment of ball screw See Mechanical Drive Train (X, Y) Section 4.2

3.2.6 Searching Axis

The handwheels are slowly turning back and forth when the servos are engaged. Several
thousandths of motion are observed on the vernier dial and the frequency is one cycle
every couple of seconds.
Perform the following Service Code and procedures:
• Code 11 Measures backlash in system. (Used only with glass scales and sensors.)
• Code 12 Sets a feed forward power constant to drive axis motors
• Code 127 Measure's the backlash in the system. Only used on machines
with Single-feedback
• Code 128 Backlash compensation on Single-feedback machines
Possible Cause Check This
Most often caused by excess backlash Check physical backlash in system and re-enter in
compensation Code 128. Run Code 11 on dual-feedback machines
High feed forward values Check ball screw torque. Typical code 12 values
should be between 10 to 15 in-lbs.
Excessive friction in the sliding ways Lubrication, gib adjustments, gib locks.
See Machine Tool & Setup - Section 4.1
Looseness in the drive train The drive train of the axis that is searching, especially
the tightness of the drive assembly.
See Mechanical Drive Train (X, Y) - Section 4.2

56
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
3.3 Problems Relating to the Operation of the Control
3.3.1 Display Blanks
The display is completely blank.

Possible Cause Check This

Where applicable, System flash drive Make sure flash drive is seated properly. SM only
loose
Screen saver has been activated Press any key to turn back on. All LED keys on
pendant will blink when the screen saver is on. Press
any key to deactivate. Hitting this key will not
activate any feature on the control.
The system has shut down Turn the power switch off; check the
computer/pendant fuses and cable connections. SM
only See Electrical Section 4.8
Poor cable connection from Computer Double-check the connection from the computer
Module to LCD (Liquid Crystal Display) module to the LCD.
Fuse blown in pendant Remove fuse and check continuity
Computer/Pendant failed See Computer/Pendant Section 4.3

3.3.2 Bad Picture on the Display

The display has strange characters, horizontal bars or other unfamiliar images, or the
display continually rolls.

Possible Cause Check This

Poor cable connection from Computer Check connections on computer module. SM only
Module to LCD (Liquid Crystal Display)
Computer/Pendant failed See Computer/Pendant Section 4.3

3.3.3 Keyboard Lockup

The screen display is normal, but the system will not respond to key presses. Perform the
following Service Codes and procedures:
• Code 81 To check if the pendant keys are working properly, press each key. If
the key is working, the corresponding key on the screen will light up. The pendant
will also beep. SM only

Possible Cause Check This

Logic Cable Test Unplug logic cable and look for 9 bars on screen.
Voltage drop/spike has occurred Shut down the system and wait 10 seconds to reboot
the system.
Remote Stop-Go (RSG) switch has a Remove the RSG. Turn the system off and then on
short (if connected) again. If the problem goes away and then re-appears
when the RSG is plugged-in, replace the RSG.
Poor cable connections from the Re-seat cable connectors by pulling out and pushing
Computer Module to the Distribution back in.
Board and from the Distribution Board
to the Keyboard
Computer/Pendant failed See Computer/Pendant Section 4.3
Where applicable, Electromagnetic Especially suspected if the network cable is run near
interference has entered through the any electrical conduit. If the problem is chronic,

57
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
network cable (if connected); especially remove the cable for a while to see if there is a
if intermittent difference.

3.3.4 Fault X, Y or Z
The program run or jogging operation is interrupted with a Fault Message on the display.
Note: EDGE, MX2 & AGE 2 do not have computerized Z-axis control.

Perform the following Service Codes and procedures:

• Code 33 Software Identification. This is needed if you call SWI Customer Service.
• Code 11 Measure's the backlash in the system. (Only used on machines with Dual-
feedback systems.)
• Code 12 Feed Forward Constant
• Code 100 Axis open loop test. Used to check the maximum feedrate of an axis and
if the encoders are counting.

Possible Cause Check This

Cable connection problems Check umbilical 1 and 2. Check #1 for X and Y-axis
problems and #2 for the Z-axis.
Table, Saddle, or Ram Locks are locked Make sure the Table, Saddle, and Ram Locks are
unlocked. High torque on any axis may cause faulting
problems during alignment routine.
X, Y, and Z-axis Gibs are adjusted Check the adjustment of the X, Y, and Z-axis Gibs
extremely tight using the X, Y, and Z-axis Gib adjustment procedures.
See X, Y, and Z-axis Gib Adjustments Section 5.2.1
Excessive friction in the slideways See Machine Tool & Setup Section 4.1
Binding or looseness in the Drive Train See Mechanical Drive Train (X, Y) Section 4.2
Incoming electrical power Incoming voltage. See Electrical Section 4.8
Measurement system not functioning See Section 4.6 or 4.7
properly
Servo Drive failure See Servo Driver - Section 4.5
Motor failure See Motor Diagnostics, Section 4.4
Computer/Pendant failure See Computer/Pendant Diagnostics, Section 4.3

3.3.5 Problems Reading the Floppy Disk; Programs Not Saved Properly;
The floppy drive will not read or write programs from a disk.

Possible Cause Check This

Improper Boot-up Shut down the system and wait 10 seconds before
rebooting
Floppy Disk failure The Floppy Disk may be bad. See if the Floppy Disk
can be read by a Personal Computer. Does the green
light on the floppy drive come on when you access the
disk? If so, power is getting to the floppy drive. If
not check connections of floppy drive inside the
computer module. See Computer/Pendant Section 4.3
for more information.
Floppy Disk full Put the Floppy Disk into a Personal Computer to see
how many bytes remain. A floppy can typically hold
1.4 MB of information.

58
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 3.3.6 System Will Not Turn On or Boot-Up
Nothing happens when the switch is turned on or the system does not boot-up.

Possible Cause Check This

110 V line is not plugged in Check incoming 110 V power source to black electrical
cabinet
Pendant On/Off switch is Off. Check the Pendant On/Off switch
Fuse blown in pendant or electrical Remove fuses and check continuity.
cabinet
Where applicable, Flash Drive failure When the Computer Module starts the boot-up
process, look at the 8th line on the Display Screen. If
the Mother Board of the Computer Module is
communicating with the Flash Drive you will see
"Detecting IDE Primary Master…Scan Disk SDCFB-64".
If the Mother Board of the Computer Module is not
communicating with the Flash Drive you will see
"Detecting IDE Primary Master … None".
Also, check the wiring connection between the Flash
Drive and the Mother Board. See Computer/Pendant
Diagnostics Section 4.3 SM only
Computer/Pendant has failed See Computer/Pendant Diagnostics Section 4.3

3.3.7 System Reboots by Itself

During operation, the screen suddenly blanks and then shows that the system has begun
the boot-up sequence.

Possible Cause Check This

Interruption of 110 V power to pendant Using a Voltmeter, check the incoming 110VAC to the
pendant.
Poor wiring and cable connections Check for any loose wiring or cables
Computer/Pendant failed See Computer/Pendant Diagnostics Section 4.3

3.3.8 System Shuts Off

During operation, the system shuts off and will not turn back on.

Possible Cause Check This

Fuse blown in pendant Remove fuse and check continuity
Poor wiring and cable connections Check for any loose wiring. Also, check the 110VAC
Power Cable connection from the 110VAC Power Strip
to the Pendant. See Electrical Section 4.8
Flash disk failure Remove and reseat the flash disk
Computer/Pendant has failed See Computer/Pendant Diagnostics Section 4.3

3.3.9 Will Not Hold Calibration

The control will not hold calibration. Go to the "Configuration Values" screen and write
down the calibration values for the motor encoders (Encoder) and the position feedback
encoders (Scales). The calibration values are written in Hexadecimal. Recalibrate the
system and see if the values change. Turn the system off and on and see if the values
are held.

Perform the following service codes and procedures:

59
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 • Code 33 Software Identification. This is needed if you call SWI Customer Service.
• Code 313 Configuration Values
• Code 123 Calibration Mode

Possible Cause Check This

Configuration file corrupt Load default configuration by going to code 313
Not saving Calibration values Replace Computer/Pendant module.
See Computer/Pendant
If calibration factors are being saved, but the measurements are not repeating or are not
accurate:
• See “Measurements Are Not Repeating”
• See “Measurements Are Not Accurate”
3.3.10 Auxiliary Functions Not Working (TRM not applicable)
3.3.10.1 AGE 3, MX3 & M3 Controls (where applicable)
The auxiliary functions will not turn on or off at the programmed times. There are 4
auxiliary functions:

1. VAC - coolant pump

2. Activates a solenoid for an air mister

3. Electrical signal to activate Haas Indexer

4. Spindle on and off

Run the following service code and procedures:

• Code 200 Auxiliary Function Test

Code 200 will turn on and off the auxiliary functions.

To test the auxiliary functions enter Service Code 200 and press INC SET. Check the LED
lights in the electrics box. For example: press auxiliary function 2, then press Turn On,
the corresponding LED light should come on and you should hear the air mister solenoid
engage. Press RSTR, then press Turn Off and LED should go off and the solenoid should
disengage. See Section 4.10 for the explanation of the LED lights.

Possible Cause Check This

Auxiliary functions malfunction Check lights on electrics box.
See Red LED Diagnostics Lights Indicator –
Section 4.10
If lights are not on, replace electrics box.
Coolant and air are not connected. Check coolant and air lines.
Coolant line clogged
Spindle will not turn on Check voltage with a voltmeter.
Voltage problem 220/440V

60
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 3.3.10.2 SM Controls (where applicable)
The Auxiliary Functions will not turn on or off at the programmed times. There are 3
Auxiliary Functions:
1. Activates or deactivates a "110VAC Receptacle" typically used for a coolant pump
or solenoid for mister.
2. Sends an electrical signal to rotate the turret on a "Haas Indexer".
3. Turns the "Spindle Off" at the end of a programmed event.

In order to run the above auxiliary functions in run mode the accessory key on the front
of the pendant must be in the AUTO mode.

All of the auxiliary function signals are carried down to the cable breakout box through
umbilical #2. Each function then has its own relay inside this box. If one of these relays
fail then these features will not work.

Perform the following service code and procedures:

• Code 33 Software Identification. This is needed if you call SWI Customer Service.

Possible Cause Check This

Bad 110VAC "Coolant or solenoid" Check if the fuse light indicator next to the plug is lit.
receptacle fuse Verify that the fuses are good or bad by checking the
resistance of the fuses using an Ohmmeter.
Poor cable connections Check all the cable connections on the cable
breakout box, Coolant Pump, and Air Solenoid
(Located on the Air Regulator). In particular check
umbilical # 2 cable, which carries the auxiliary
function signals.
Faulty "Indexer" connector Check for continuity between pins 3 and 4, when the
output of the Haas Indexer connector is activated.
Bad cable breakout box Check 110 V power coming out of the AC E-stop port
with the E-stop in the out position. This will cause
the spindle to not run.

3.3.11 E-Stop Error

The E-Stop turns the power off to the axis and spindle motors. This is done by breaking
the 110 V contact.
Spindle Motor Electrical Box
110V Power reaches the electrical box through the AC E-stop cable. It is used to
energize the spindle motor contactor. If this contactor is not energized, the spindle will
not turn on.

If the E-Stop button is depressed, and no message is displayed on the screen, either the
E-Stop button or the Computer Module is at fault.

61
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Possible Cause Check This
Faulty E-Stop switch Check the cable connections from the computer
module to the E-Stop switch. Check the E-Stop switch
for functionality.
Bad pendant Does 110 V power come out of the cable breakout box
power cord on the pendant? If yes, and the screen
has an E-stop message, replace the pendant.

3.3.12 Limit Switch Error - Optional

Limit switches are installed on the table, saddle, and ram to prevent serious damage to
the machine in the event of a crash. In the event a limit switch is triggered, a limit
switch error will appear on the screen.

Critical Error 64: Servo Error

X-axis Limit Switch
Correct the fault condition and continue.

To return the machine to its normal state of operation, perform the following procedure:
1. Use mechanical handwheels on X and Y to move switch off the trigger. For the
Z-axis, manually lift the arm on the trigger to return the limit switch to its normal
position. Then jog the ram up or down as necessary.
2. Press the "Mode" or "Return" key to reset the control
3. Press the "DRO" key to enable the machine to once again jog.

Possible Cause Check This

Limit switch jumpers in cable breakout Remove and reseat jumpers.
box are making poor contact.
Limit Switches are triggered Reset the Limit Switches using the procedures
described above.
Poor Limit Switch Cable connection Check for any pins that are loose, pushed in, or bent.
Verify that there is a good connection between the
cables on the cable breakout box.
Limit Switch failure Does the limit switch problem move to the other axis?
If it does then the switch is most likely the problem.
Try this If it stays with the original axis then it could be the
Switch 2 limit switch cables on the cable cable breakout box.
breakout box.

3.4 Problem with the Measurements

3.4.1 X, Y and Z-Axis Measurements Do Not Repeat
With a dial indicator mounted to the bottom of the spindle, touch off a fixed surface
either in the X or Y-axis direction and then set the DRO equal to 0. Crank away several
inches and then touch off again at the same place. If the reading has not returned to 0

62
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 on the DRO, zero the display and repeat the procedure. If the measurement does not
repeat, you have a repeatability problem that must be resolved.

Test for accumulative error by moving the axis a number of times to see if the error
gradually grows by a small amount. If so, it may be caused by a misaligned sensor or
scale. If the error abruptly changes by a large amount, it may be caused by a bad encoder.

Expected repeatability numbers should be 0.0005” or less.

Perform the following service codes and procedures where sensor/glass scales are used:
• Code 304 Toggle X sensor/glass scale on/off – SM only
• Code 305 Toggle Y sensor/glass scale on/off – SM only

Possible Cause Check This

Machine Tool & Setup problem Check for any looseness in the setup (Tool, Tool
holder, Part, Vise, or Fixture). Make sure there is
sufficient contact between the tool holder and the
spindle. See Machine Tool & Setup Section 4.1
X, Y, and Z-axis Gibs are loose Check the adjustment of the X, Y, and Z-axis Gibs
using the X, Y, and Z-axis Gib adjustment procedures.
Where applicable, TRAK Sensor or Glass Make sure that the Sensor or Glass Scale is installed
Scale problem correctly according to the Sensor or Glass Scale
Installation procedures. Check for any loose brackets
or misalignment etc. Also, check to make sure the
Sensor or Glass Scale assemblies are functioning
correctly. Use service codes 304 for X and 305 for Y
to turn off the suspect encoder. Does problem still
exist after turning it off?

Possible Cause Check This

X and Y-axis Drive Trains are loose Check Repeatability using the Repeatability and
Positional Accuracy procedure. Step by step, carefully
inspect the Drive Train for any looseness. It may be
necessary to disassemble and then reassemble the
Drive Train. See Mechanical Drive Train (X, Y)
Section 4.2
Encoder Disk or Reader Head on motor Swap the motor in question with a known good motor.
are loose For example, swap the X-axis motor with the Y-axis
motor. If the symptom stays with the motor in
question, then replace the motor. If not, then the
motor is not at fault and something else is causing the
problem.
Spindle and/or Quill are loose Use a Dial Indicator and check for side-to-side
movement between the Spindle and the Head. Next,
check for side-to-side movement between the Quill
and the Head. There should be no more than 0.0003"
of side-to-side movement. Make sure that there is a
few thousandths gap between the Spindle Collar and
the Quill after tightening.
Head bolts are loose Tighten Ram bolts

63
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 3.4.2 X, Y, and Z-Axis Measurements are not Accurate
Measurements repeat, but with a dial indicator mounted to the bottom of the spindle,
traversing the length of a gage block or some other measurement standard, the
measurement is not accurate.

Note: If your part has incorrect dimensions, see Parts Have Incorrect Dimensions,
Section 3.1.4.

Note: First check for repeatability of the DRO: With a dial indicator mounted to the
bottom of the spindle, touch off a fixed surface either in the X, Y, or Z-axis direction and
set the DRO equal to 0. Crank away several inches and touch off again at the same
place. If the reading has not returned to 0 on the DRO, zero the display and repeat the
procedure. If the measurement does not repeat, you have a repeatability problem that
must be resolved before the accuracy problem can be resolved. See Measurements That
Do Not Repeat, Section 3.4.1.

Possible Cause Do This

The Calibration is incorrect Recalibrate the machine.
See Calibration & Backlash Constants – Section 5.2.2
Incorrect backlash values If the machine does not repeat bi-directionally check
the backlash on the axis in question.
See Section 5.2.2.

3.4.3 The DRO is not Counting

The DRO for one axis is not counting when an axis is moved. Often times if this is the
case the axis will fault. See Faulting Axis Section 4.7.1

Perform the following Service Codes:

• Code 33 Software Identification. This is needed if you call SWI Customer Service.
• Code 100 Axis open loop test. Used to check the maximum feedrate of an axis and
if the encoders are counting.
• Code 304 & 305 Turns off X and Y sensor or scale where applicable. SM control
only

Possible Cause Check This

Servo driver failure See Servo Driver Section 4.5
Motor Encoder not counting See Motor diagnostics (not applicable with Glass Scale
option)
Glass Scale or Sensor Failure Does axis now count? If so, replace scale.
Computer/Pendant failure See Computer/Pendant diagnostics

3.4.4 X, Y, and Z-Axis DRO Counting in Wrong Direction

The DRO is counting in the wrong direction.

The positive directions for each axis are:

• X-axis – Table moves to the left
• Y-axis – Saddle moves toward the front of the machine
• Z-axis – Ram moves up

64
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Perform the following service code and procedures:
• Code 33 Software Identification. This is needed if you call SWI Customer Service.
• Code 313 Check the line that specifies the product.
• Code 97 Axis configuration

If the product does not match the machine, the machine ID key will need to be replaced.

3.4.5 X, Y, & Z-Axis Electric Handwheels Count in Wrong

Direction
The Electric Handwheels turn in the wrong direction.
The positive directions for each Electric Handwheel are:
• X-axis - Electric Handwheel turns clockwise
• Y-axis - Electric Handwheel turns counterclockwise

Perform the following service code and procedures:

• Code 308 Reverse X-axis Handwheel Direction – SM only
• Code 309 Reverse Y-axis Handwheel Direction – SM only

3.5 Problems with the Machine Tool

3.5.1 Z-Axis Noisy
While jogging or cutting in the Z-axis direction, the axis makes unusual noises. See
below for head noise.

Possible Cause Check This

Machine Tool and Setup problem Check for any looseness in the setup (Tool, Tool
holder, Part, Vise, or Fixture). See Machine Tool &
Setup Section 4.1
Ram Locks are locked Make sure the Ram Locks are unlocked.
Inadequate or no Lubrication to the Make sure all the Way surfaces are getting proper
Ballscrew and Way surfaces lubrication. If not, check to make sure that the lube
pump is functioning properly. Also check for any
pinched or blocked oil lines. See Lubrication
Section 4.1.3
Z-axis Gibs are not adjusted properly Check the adjustment of the Z-axis Gibs using the Z-
axis Gib adjustment procedure. See Z-axis Gib
Adjustments Section 5.2.1
Mechanical Drive Train Misalign ballscrew, or top and lower bearing failure.
Z-axis motor failure Replace Z-axis motor
See Motor Diagnostics Section 4.4

65
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 3.5.2 Spindle Stalls or Turns-Off During Machining
During machining, the spindle turns off and loses power. First check incoming voltage
and connections.
Possible Cause Check This
Machine Tool and Setup problem Check the type of material being cut, type and size of
cutting tool, RPM, and Feed rate. Also check the
condition of the cutter to verify that the cutter is not
dull. See Machine Tool & Setup Section 4.1
Drive Belt in the head is slipping Check the alignment, condition, and tension of the
Drive Belt.
Cut more than the machine is capable Check width and depth of cut

3.5.3 Spindle Motor Hums or Will Not Run

The spindle motor makes a constant humming noise during operation or will not turn on.

Sport and SM models only: If the spindle does not run, you must make sure 110 V
power is reaching the spindle motor contactors in the electrics box. Check your 110V
power across terminals wire 3 and ground. If power is not reaching the electrical
cabinet, but is reaching the cable breakout box, then most likely a relay has failed in the
cable breakout box. The cable breakout box will need to be replaced. This relay is in
series with the 110 V power in the E-stop circuit. See Section 3.3.11. If power has
reached the electrical box then use the schematic in Section 4.8 for how the power is
routed.

Possible Cause Check This

Wrong voltage Check the 220V/440V voltage to the machine

Poor wiring connections Check all the wiring connections to the electric’s box.
Defective cables or poor cable Check all cable connections
connections
Spindle Motor is bad Check the resistance of the Spindle Motor windings on
the Spindle Motor between L1 & L2, L2 & L3, and L1 &
L3, using an Ohmmeter. The resistance should range
from ".7 to 1.2 Ohm" for the DPMS3, from “.5 to .9
OHM” for the DPMS5, and from 1.0 to 1.8 for the
DPME2. If the Ohmmeter reads "0 Ohms" or "OL",
replace Spindle Motor. Next, check the resistance
between L1 & Ground, L2 & Ground, and L3 &
Ground, using an Ohmmeter. The resistance should
read "OL". If not, replace Spindle Motor.
Spindle will not run because 110 V Check 110 V coming out of the AC e-stop port on the
power is not reaching the spindle cable breakout box. Relay failure in cable breakout
contactor box. Replace cable breakout box – Sport and SM.

3.5.4 Spindle Runs Backwards

The spindle motor runs in the opposite direction. The spindle will run in opposite
directions from high to low gear.

66
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Possible Cause Check This
3-Phase wires backwards Need to switch any 2 of the 3 wires either coming into
the machine or motor. Note: Caution: Be sure to shut
off all power to the machine before attempting to
switch any wires.

3.5.5 Spindle motor intermittently stops and starts or does not

operate
Possible Cause Check This
In spindle control electrics box, loose Ensure that the screws on the FWD/REV relays are
screws holding the spade lugs down to holding down the spade lugs and that the screws are
the FWD/REV relays, causing tight.
intermittent contact.
In spindle control electrics box, Ensure that the spade lugs are installed back to back
FWD/REV contactor-wiring spade lugs on the FWD/REV relays, that the screws are tight, and
installed improperly, causing loose that the spades are fully locked beneath the hold-
contact or burned wires. downs.

3.5.6 Head Noise

Head noise pertains to any unusual noises coming from the head under load and no load
situations. Most often head noise will only be noticeable under load situations. It is
important to try to distinguish between problems with components in the head versus
problems caused by the setup or tooling being used on a particular job. Use the table
below to try to pinpoint the possible cause. Also try to pinpoint the noise by seeing if it
exists in high, low or neutral. For example, if the noise is evident in neutral then this
eliminates the spindle bearings.

Possible Cause Check This

Machine setup or tooling problem If the noise is most evident under load (cutting
situations) then it is important to look at setup and
tooling being used. Ask the following questions.
Is the cutter dull? Is the tool loose in the holder? Am
I taking a bigger cut then is possible on the machine?
Is the part moving in the vice? Am I using realistic
speeds and feeds?
Any one of these can have a significant impact.
Upper spindle bearing is worn out. Remove the upper bearing plate above the spindle.
This will unload the bearing. If the noise goes away
then this bearing should be replaced.
Verify nosepiece is tight on bottom of To check if the nosepiece is bottomed out try to insert
spindle. a piece of paper in between the nosepiece and the
quill. If a piece of paper does fit then this may be the
problem. Before tightening or loosening the
nosepiece make sure to loosen the setscrew that
holds it in place.
Spindle bearings are worn out This is categorized by a high pitch sound and is most
evident at high RPM’s. It should also cause chatter
under load. Replace the spindle if this is the case.
See spindle replacement in Section 5.

67
Southwestern Industries, Inc.
TRAK and Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 4.0 Diagnostics
This section explains the diagnostic procedures used to isolate service problems.

4.1 The Machine Tool & Set-Up

4.1.1 The Milling Machine Checklist
The following is a quick reference for the types of problems that may arise if problems
are noticed in these areas.

Problems With: Can Contribute To: Most Suspect When (and why):
Spindle bearings Noisy head Older machines, machines that are
See Spindle Replacement Poor finish pushed hard
Circles out of round
Lubrication system Premature wear of ball screws, New installations (may not be
wear surfaces hooked up or line sheared)
Poor finish
Inadequate lubrication habits Premature wear of ball screws, New installations (more motion than
wear surfaces the machinist is used to with a
Poor finish manual mill) Lubricate machine
every morning before use.
Gib locks - on X and Y axis If locked can lead to axis faults. Note: when using the CNC to
machine, never tighten the gib locks!
X and Y gibs loose Taper on straight Y moves When machine hasn’t been serviced
See Gib Adjustment - Section 5.2.1 Poor finish in a long while.
Circle out of round
Gibs too tight Not getting to position, does not N/A
repeat, axis faults
Poor finish
Gibs floating Not getting to position, does not Contact area of gibs. May need to
repeat, axis faults be scraped. Very old machines may
Poor finish not have any more adjustments on
gib. A new gib will need to be fit on
the machine.
Gibs defective - bowed, scarred Excess play when gib is checked Inadequate gib contact
side to side

Way surfaces pocked, scarred, or Poor finish Inadequate lubrication

excessively worn Out of round circles
Faulting
Ram gibs loose Parts incorrect dimensions Vibration or jerky motion in Z axis
Head out of tram in Y direction.
Machine not level Parts incorrect New installation or heavy crash.
Weight not distributed evenly on all Machine geometry off, i.e. tram.
six screws
See Leveling procedures
Head out of tram Leaves uneven surfaces on Machine not level, ram gibs loose.
See Tramming Head - Section 5.2.3 bottom of pockets.

68
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 4.1.2 A Special Word About X/Y/Z Gibs
The slideway surfaces are vital to the performance of the bed mill.
Gibs should be:
• flat
• free of twist
• free of burrs
• free of blockages in the oil passages and channels
Defective or scarred gibs must be replaced. Shimming of gibs will not yield acceptable
results.
It is good machining practice to avoid the use of shop air to clean the chips off a
machine. This risks blowing chips into the sliding way surfaces and compromising the
performance of the machine.
Gibs that are not adjusted correctly will affect the performance of the machine. It will
lead to positioning and repeatability problems. The gibs should be adjusted at least
twice a year.
See Gib Adjustments Section 5.2.1.
4.1.3 Lubrication
Lubrication is one of the single, most important maintenance issues and plays a key role
in assuring the performance and durability of the bed mill. At the beginning of each day
manually supply oil to the way surfaces.
Lack of lubrication can lead to a variety of problems with your machine motion due to
increased friction in the sliding ways. This increased friction may lead to part
inaccuracies and decreased life expectancies of your ball screws and way surfaces.

4.1.4 Machining Set-Up

The machining set-up can greatly influence the performance of your mill. Be aware of
the following:

Problems With Can Contribute To:

Feed and Speeds (spindle rpm) Poor finish
See below Machine chatter
Excessive speeds and feeds can break cutting
tools or wear tools prematurely.
Tooling Poor finish
Using the wrong cutter for an application
Entering the wrong size diameter and Parts incorrect size
programming with tool compensation.
Cutting too deep Part dimensions incorrect
Driving and cutting forces cause deflections,
since no material is totally rigid
Machine chatter
No coolant Poor finish, decrease the life of the cutter

69
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 4.1.4.1 Spindle Speeds
Spindle speeds are influenced by a number of variables:
• Material
• Rigidity of the Machine Setup
• Coolant
• Cutter type, material and diameter
• Cutting Depth
As a general rule:
• Lower spindle speeds are used to machine hard or tough material or where heavy
cuts are taken.
• Higher spindle speeds are used to machine softer materials in order to achieve
better surface finishes. Higher speeds also apply when using small diameter cutters
for light cuts on frail work pieces and delicate setups.
Note: Cutter diameter greatly affects spindle speeds. The larger the diameter, the lower the
spindle speed.

4.1.4.2 Feedrates
Factors that affect feedrates:
• Depth and width of cut
• Design or type of cutter
• Sharpness of the cutter
• Workpiece material
• Type of finish or accuracy required
• Climb or conventional milling
If a fine finish is required, reduce the feed rather than increase the spindle speed.
Cutters are dulled by higher spindle speeds rather than high feedrates.

4.2 The Mechanical Drive Train (X, Y)

Indications:
• Troubleshooting instructions indicate that the drive train is potentially the problem
and other (more easily checked variables) have been exhausted.
• Roughness, looseness, tightness or jamming movement in the table or saddle.
1. Check for machine considerations, especially gib locks and gib adjustments.
See Gib Adjustments Section 5.2.1.
2. Check the torque of the axis in three places (both ends and center of ball screw)
along the length of the ball screw. The torque should be within 2 or 3 in-lbs across
the length of the ball screw. If it is not, chances are the ball screw is misaligned. A
misaligned ball screw can lead to parts being out of round and servo problems at
low feedrates. A bad ball screw can also cause high torque, although this is highly
unlikely. See Sections 4.2.1 for more information.

70
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 Note: The following steps take you in logical sequence through the assemblies. For
drawings of these assemblies see Figures 5-12 through 5-25 in Section 5. These
instructions break the machine down from fully assembled and point out the areas to
look at specifically.
3. Check that the belt is properly tightened. A loose belt can lead to excessive
backlash compensation values on motor encoder only machines.
4. Check that the nut that tightens up against the ball screw pulley is tight. If this is
loose the pulley may not run true on the ball screw.
5. Check that the tapered sleeve that seats the pulley has not clamped to the ball
screw prematurely. It should be seated firmly against the pulley. Tightening the nut
may not have ensured this. Also make sure the pulley is keyed to the ball screw.
6. X-axis for all models - Ensure that the screws that hold the bearing housing in place
to the bracket are not loose.
7. Y-axis - Ensure that the bearing housing is clamped in place by the bracket. This
design uses the bracket to secure the bearing housing in place. It should not allow
the bearing housing to float between the bracket and machine.
8. Ensure that the Clamp Nut is secured. The following applies to the clamp nut:
• When loosening, make sure to back out the 10-32 screw from the clamp nut.
• When tightening, snug the 10-32 screw so the clamp goes onto the ball screw
thread with some drag. Thread it onto the ball screw and torque the clamp nut
to 50 ft/lbs and then tighten the screw down.
9. Take out the angular contact bearings and inspect them. They should roll smoothly
and be lightly greased. If not, replace them. When putting the bearings back into
the housing make sure to put them in correctly. Failure to do this will cause
problems. The thin race of each bearing should be facing inward toward the spacer
ring.
Note: the bearing housing and spacer ring are matched sets - keep them together.
10. Check the ball screw mounting to the yoke. Make sure the SHCS are tight.
11. Inspect the ball screw, ball nut and yoke for the potential problems shown in the
chart on the next page.

CAUTION!
Unlike a lead screw, do not unscrew the ball screw from its nut. This will destroy the ball screw!

Potential Problem: Check By:

Bad ball screw • Visually inspecting the ball nut - if the nylon seal is broken or
deformed, if contamination has visibly entered the ball nut or if balls
are out of the ball nut, replace the ball screw.
• Cranking the ball screw through a significant part of its travel. If it
jams, feel loose or has rough spots, replace the ball screw.
• Using the dial indicator on a vertical flat of the ball screw to check for
backlash between the ball screw and ball nut.
Potential Problem: Check By:
Ball nut not tightened to • Inspection for space between the head of the bolt and the ball nut i.e.
the yoke the retaining bolt has bottomed out in its thread and is not securing
the ball nut to the yoke properly.

71
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
Yoke loose in the saddle • Inspection for any motion of the yoke or looseness in the Yoke
mounting screws.
Oil lines sheared • Visual inspection.
Oil line blockage • Pump the oil and ensure that it flows evenly to the ways and ball
screw.
Ball screws not aligned • Measure from the ball screw to the back of the saddle on both sides of
properly the yoke (the table must be removed). The measurements must be
within ±.005” end-to-end. See above explanations.

Note: Ball screws are inspected throughout their entire travel for backlash and
consistent torque. A ball screw should be good for millions of inches of travel if installed
properly. Do not be too quick to replace a ball screw if there is insufficient indication
that it is bad; this will just be a costly delay to resolving the real problem.
4.2.1 Ball Screw Alignment
4.2.1.1 TRM, DPM, Sport B3, DPMS3, DPME2 Ball Screw Alignment
• X-axis – there are 3 components that can cause misalignment: the yoke, the left
side bearing housing bracket, and the right side bearing housing.
• Yoke – the yoke is aligned at the factory and pinned in place. It is aligned to within
0.0005” with a precise alignment tool. The yoke most likely is not causing the
problem. If this were the problem you would need to remove the pins and align the
X ball screw with the back of the saddle. Drill new holes and pin the yoke in place.
The Y-axis ball screw bore is machined perpendicular to the X bore. If the X-axis is
aligned the Y-axis will also be aligned.
• Left-side table bearing housing – this is most likely the cause of the
misalignment. To align the bracket and bearing housing, move them as close to the
yoke as possible. Loosen the bracket bolts and bearing housing bolts and then
retighten. This should allow the bearing housing to align itself up with the yoke.
• Right-side table bearing housing – once again move the bearing housing as
close to the yoke as possible. Loosen the bearing housing and retighten. This
should allow the bracket to align itself. If you do not move the table toward the
yoke the ball screw will tend to bend down slightly and cause misalignment.
• Y-axis – the only component that can cause a misalignment problem is the motor
mounting bracket. To align this bracket, move the saddle as far to the front of the
machine as possible. Loosen the bracket and then retighten it. Once again moving
the saddle forward allows the yoke to be as close to the bearing housing as possible.

4.2.1.2 DPM5, DPMS5 & Sport B5 Ball Screw Alignment

• X-axis – there are 3 components that can cause misalignment: the yoke, the left
side bearing housing bracket, and the right side bearing housing. This machine has
a separate yoke for the X and Y-axis.
• X Axis Yoke – the yoke is aligned at the factory. If you suspect the yoke is
misaligned, the bolts for the yoke can be accessed from an opening on the bottom
left side of the saddle. Break these bolts free and move the table back and forth
along its travel and then retighten the bolts.
• Left-side table bearing housing – To align the bracket, move the yoke (table
left) as close to the bracket as possible. Loosen the bracket bolts and then
retighten. This should allow the bearing housing to align itself up with the yoke.

72
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 • Right-side table bearing housing – once again move the yoke as close to the
bearing housing as possible (table right). Loosen the bearing housing and retighten.
This should allow the bracket to align itself. If you do not move the table toward
the yoke the ball screw will tend to bend down slightly and cause misalignment.
Make sure the mechanical handwheel is not causing the misalignment.
• Y-axis – the only component that can cause a misalignment problem is the motor
mounting bracket. To align this bracket, move the saddle as far to the front of the
machine as possible. Loosen the bracket and then retighten it. Once again moving
the saddle forward allows the yoke to be as close to the bearing housing as possible.
The yoke is pinned at SWI should not become misaligned unless the machine has
been repeatedly crashed.

4.3 Computer/Pendant Diagnostics

4.3.1 Diagnostics for Computer Modules contained in Pendant
– EDGE, SM3, M3
The pendant consists of 2 separate modules: the computer module and screen/
enclosure – SM and EDGE only.

In general, the pendant/computer module is best diagnosed by eliminating all other

possible alternatives. The following table lists some problems and what these problems
can lead to. Make sure to first unplug any accessories like the Remote Stop/Go switch,
external keyboard, mouse, etc. to eliminate any interference.
Possible problems Can lead to
Poor cable connections There are 4 cable connections to the left side of the
pendant. Make sure all cables are properly fastened.
SM only
Pendant locks up Press the E-stop button and see if lock up clears if not
then do the following:
Turn the pendant off, wait at least 30 seconds, and
turn it back on and check to see if the malfunction has
been reset.
No voltage to RSG port RSG will not work – should be 5 DC volts present
Check with a voltmeter. SM only
Low voltage to flash drive or slave board. Can cause the system to lock up and the flash drive to
act abnormally. Check voltage to power cable at flash
(EDGE & M3 have no flash drive) drive module with voltmeter. It should be 4.8 DC
volts and above. Lower values than this can cause
problems. SM only
Where applicable, Flash disk failure If the flash disk fails, the system will not boot up or
operate. It will need to be replaced. All programs
and machine configurations will be lost. Make sure to
back up your flash disk from time to time.
Floppy disk failure Will not allow user to save or pull up programs from a
floppy disk. See Section 4.3.1.
LCD backlight burns out – SM only Check all cable connections to LCD, distribution board
and computer module. Make sure the power is turned
off before doing so.

73
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 Possible Problems: Can Lead to:
Overlay failure (keys on pendant) Certain buttons on overlay do not work. Do code 81 to
verify each key beeps.
Low voltage to pendant or current 1 amp fuse in pendant blows. Pendant will not turn on.
spikes
Slave Board not functioning If no slave data is found in Code 33, replace the module.

4.3.2 Diagnostics for Computer Modules Separate from Pendants

– AGE2, AGE 3, MX2 & MX3
Indications:
• Problems that are manifested in the Display Pendant (e.g. Blank Screen), but the
Display Pendant passes the logic cable test.
• There are problems with axis motion.

Objective:
• To determine if the computer module has failed.

Note: SWI's exchange program provides for an exchange of the entire computer module
once a problem has been isolated to this subassembly. This makes it unnecessary to
identify the exact nature of the failure within the computer.

1. Open the computer cabinet. Be sure to clean the area around the cabinet first so
that chips are not allowed to enter the computer module.

2. Check the floppy disk drive lights. There are two drives with exception to the MX2,
which has one drive.

3. Check the fuses.

Drive How to Check When to Check

Turn the system off and then back on. Observe the floppy
Bottom – drive light as the system boots up. It should come on and Problems with the
System disk stay on until the "Select Mode" or Main Menu screen system booting up
appears.
Top – While in the Program In/Out mode, give the system a Store
Problems loading in
Part Programs or Retrieve command and observe the light. It should come
the part programs.
Disk on after the system command is given.

4. With the system power on, check the large orange light at the bottom left of the
cabinet. This indicates whether the power strip assembly is receiving AC power.

5. Check the LEDs that are mounted to a PC board on the right side of the cabinet.
These LEDs may be viewed through a slot through the black sheet metal cover. You
may also remove the sheet metal cover. Use the following guidelines for diagnoses
with the LEDs.
CAUTION!
The computer cabinet contains voltages that are very dangerous.

74
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 Position Purpose Comment
Should be on whenever the system is on.
If not, replace the computer module.
Top Indicates power to the motherboard
Check to see if power is reaching the
computer module.
Indicates if the system is receiving counts View the light while moving an axis of the
Middle from the independent position encoder. machine using a handwheel. The LED
(TRAK Sensor) should flicker as the axis moves.
Indicates if the slave board is sending a
View the light while moving axes under
Lower command to the motors. (Motor Encoder
power. The light should be on.
counting)

Failure of these lights to come on during the operations shown above indicates that the
computer module should be replaced.

4.4 Motor Diagnostics

The Motor subsystem is comprised of 2 parts: The Motor Encoder and the Motor. The
motors are powered by 110 VAC voltage. The servo driver is also an integral part of
servo system, which is discussed in detail in the next section.

WARNING!
Do not work with the motors unless the power is disconnected from the machine. The motors
are run by 110 VAC. There is possibility of death by electrocution!

Rarely do both the X and Y motor/servo systems fail at the same time and in the same
way. So, if your problem is occurring on both axes, its source is probably somewhere
else.

4.4.1 Cable Connections

Check the motor cable connections on the cable breakout box. Verify there are no
pushed in pins on the connector.

4.4.2 To Check the Motor Encoders

If the motor encoder inside the motor has failed or is not reading the machine will fault
out on that axis. Do the following to verify this problem:
Motor encoder and secondary feedback machines – run Service Codes 100. Both the
motor encoder and sensor or glass scale encoder should count on the DRO screen. The
motor value should be displayed under the Z-axis and the sensor or glass scale under
the X or Y-axis depending on which axis you are doing.

4.4.3 Encoder Counts to Pendant

SM/M Products only – Before replacing the motor due to a bad motor encoder it is a
good idea to check the cables that take those signals back to the pendant. If these
signals are not getting back to the pendant then the axis will fault. Check the following
cable connections.

• Umbilical #1 and #2 at the cable breakout box

• Umbilical #1 and #2 at the pendant

75
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 • Umbilical #1 carries the X and Y-axis signals and Umbilical #2 carries the Z
signals.

4.4.4 Moving Problem from One Axis to Another

Another way to troubleshoot a problem with a particular axis is to swap parts from 1 axis
to another to see if the problem moves. If the problem moves then that component is
faulty. See the example below.

Symptom – X Axis will not move and faults

This could be due to a bad motor, servo driver, or computer module, but it is not always
obvious which component is causing the problem. In order to determine which
component is causing the problem try the following:

Swap these components Results

Physically switch the X and Y Has problem moved to Y-axis? If yes, replace amp. If no, the
servo amp motor is the problem.

4.5 Servo Driver

Note: the Servo Driver is located in the black box on the side of each motor.

WARNING!
Do not work with the Servo Driver unless the power is disconnected from the machine. There is
possibility of death by electrocution!

Indications:
• Problems moving just one axis, including hard turning in one direction.

Objective:
• Isolate the problem to the particular Servo Driver

Steps:
1. Turn off and unplug the system.

2. Physically swap the servo module from the axis that is not working to one that is.

Note: To avoid pulling the wires out of the connector, use the loop to pull the connector from the
Servo Driver.

If the problem moves to the other axis and clears up from the original axis, replace the Servo
Driver.

4.6 Glass Scales

The Z glass scale is standard with the following machines: DPME2, TRM, DPM, DPMS3,
DPMS5, & Sport B3. The X and Y-axis glass scales are optional for the DPMS3 and
DPMS5 machines for secondary feedback only.

4.6.1 Alignment of Scales

• X Axis - The X-axis scale must be aligned within 0.005” in the up and down
direction over the length of the scale for proper operation. Misalignment can

76
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 cause the scale to not read in the certain areas of the scale that are not aligned
with the reader head. If this happens, the axis will mostly likely fault out in this
area. Also make sure the mounting hardware for the reader head is tight.
Loose hardware can cause excess backlash when reversing direction.

To align the scale, place a 0.001” indicator on the bed ways and on top of the
scale extrusion. Move the table along its full travel from one end to another to
verify it is aligned. If the scale is misaligned loosen the 2 screws at either end
to shift the scale up or down as needed. You will also need to loosen the center
support bracket to allow the scale to pivot.

• Y Axis - The Y-axis must be aligned in the up and down direction and must be
parallel to the Y-axis way surface. Both surfaces must be aligned to within
0.005”. Failure to align the scale properly could cause the same problems as
mentioned above. Mount your 0.001” indicator on the saddle and move the Y-
axis back and forth along its travel.

• Z Axis – The Z scale must be aligned parallel with the quill. Make sure the gap
on the readerhead is consistent along the length of travel. Align the scale within
0.005” up and down.

See Figure 5-8 for an illustration of the Z glass scales.

4.6.2 Measurements Do Not Repeat

1. Determine if the error in repeatability is random or accumulating:
• Mount a dial indicator in the quill.
• Touch off a fixed point on the table and set the DRO and indicator to 0.
• Traverse away approximately 6 inches.
• Return the touch off again at DRO 0 point.
• Compare with indicator reading.
• Do not Re-zero the DRO, traverse away and return several times.
• Again, compare DRO with indicator reading.
Note: Random error will be unpredictable and give scattered readings, adding and/or subtracting
the error after each traverse with no pattern. See Step 2.
Accumulating error will add roughly the same amount to the reading after each traverse.
See Step 3.
2. For random error, look for problems in the set-up of the glass scale that have
resulted in a loss of rigidity. Common sources of random error include:
• Loose scale mounting hardware.
• Loose reader head.
• Very loose motion of the table or saddle.
3. Accumulating error is commonly the result of:
• Scale out of parallel to the axis travel.

77
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 • Dirt or chip on the glass scale.
• Broken glass.

4.7 TRAK Sensors – TRM, DPM, & DPM5 (optional on

DPMS3, DPMS5, Sport B3 & Sport B5)
TRAK Sensors are used on the X and Y-axis for secondary feedback. The following section talks
about some of the common symptoms associated with a problem sensor and how to isolate or
fix the problem.

Common symptoms
• Faulting Axis
• The DRO measurements do not repeat
• The DRO measurements are not accurate

Objectives:
• To determine if the TRAK Sensor is bad and needs to be replaced.
• To determine if there is a problem with the sensor set-up
4.7.1 Faulting Axis
If a sensor has stopped reading and you try to move an axis, the axis will run away and
fault. Our control uses the counts from the sensor and motor when reading position. If
either one of these signals is not working, our system will fault.
1. SM only – The first thing that can be done to see if it is the sensor is to turn off
the sensor on the axis in question. This will allow the system to run only on the
motor encoders. If the fault continues then the sensor was not the problem.
Turn the sensor back on. See the Service Code Section for codes needed to turn
the sensors on and off.
2. The next thing to do is to visually inspect the sensor and base to determine if
there has been a crash. A damaged base will usually have crinkles in the small,
triangular plates on the front and back.
3. Next make sure the sensor is preloaded correctly against the running surface.
There is a setscrew on the base that allows for adjustment.
4. If no outward signs of damage are present, remove the sensor from its base,
and inspect the wheel for damage and wear.
Look for chip contamination in gauge wheel and damage to running surface.
If the wheel is worn smooth in the center, replace the sensor.
Note: Sensors should not wear smooth for many years of normal operation.
5. If the sensor looks normal, it is probably OK and there is a mechanical
obstruction somewhere in the set-up. Look for the following possible problems:
• Broken or loose sensor base
• Broken or loose bracket
• Sensor tilted too much (so that the wheel is not engaging the running
surface)

78
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 4.7.2 Measurements Do Not Repeat
1. Determine if the error in repeatability is random or accumulating:
• Mount a dial indicator in the quill
• Touch off a fixed point on the table and set the DRO to 0.
• Traverse away approximately 6 inches
• Return and touch off again
• Write down the reading on the DRO.
• Do not re-zero the DRO, traverse away and return several times
• Write down the DRO readings
Random error will be unpredictable and give scattered readings, adding and/or
subtracting the error after each traverse with no pattern. See Step 2.
Accumulating error will add roughly the same amount to the reading after each
traverse. See Step 3.
2. For random error, look for problems in the set-up of the TRAK Sensor that have
resulted in a loss of rigidity. Machines that have TRAK Sensors are TRM, DPM, &
DPM5 (optional on DPMS3, DPMS5, Sport B3 & Sport B5).
Common sources of random error include:
• broken base
• broken bracket
• loose puller screws
• loose run bar
• very loose motion of the table or saddle
• loose clamp screw
3. Accumulating error is almost always the result of the wheel not traveling in a path
parallel to the motion of the axis. This causes the wheel to skip at certain regular
points in its travel.
• Inspect the base to determine if it has been damaged. A damaged base will
usually have crinkles in the small, triangle-shaped plates on the front and
back.
• Use a bubble level or an indicator to adjust the puller screws so that the
base is parallel to the running surface.
• Inspect that the sensor is not cocked so that the case contacts the running
surface.
• Inspect the wheel for chips that are adhered or for gouges.

4.8 Electrical
4.8.1 Checking A/C Voltage
This procedure tests for the 115V power for the control.
• Use a Voltmeter, reading A/C volts.
• Acceptable range is 100V to 130V.

79
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 Note: systems running consistently close to the low values may have problems when
normal voltage fluctuations push the voltage out of the acceptable range.

Test the following in the order presented:

Problems Here: May Indicate:

1. The wall outlet. • Fuse blown in the shop electrical panel.
• Incoming service from local utility is bad.
Call the electric company.
2. The control power cord from the wall. • Power cord defective.
Check the end that goes to the electrics
box.
3. Check the top fuse on the electrical • If this is blown then power will not reach
cabinet. It should be an 8-amp fuse. the 4 outlets on the electrical box – SM
and M only.
4. Check the 110 power cord to the pendant. • Power cord defective

4.8.2 Checking Fuses

To check all fuses:

1. Use a Volt/Ohmmeter; select “OHM”.

2. Remove the fuse completely from the pendant, electrics box or cable breakout box.

3. Place a lead of the meter on each end of the fuse.

• A good fuse reads 0 (zero) or close to it.
• A bad fuse reads Open or Infinity.

4.8.3 Cable Breakout Box Connections -

Sport, DPMS3 & DPMS5 only
This module is located on the backside of the machine. It consists of 3 motor
connections, 3 limit switch connections, 3 encoder connections and an E-stop
connection.

Machines with an auxiliary function option have 2 more outlets. A 110 V outlet for a
coolant pump or air solenoid and an indexer outlet.

The coolant pump signal and indexer signal comes down from umbilical #2.
4.8.4 Cable Connections
The milling machines use several cables to communicate between systems. What
appears to be the failure of an electrical component might be due to a poor connection.

Indications:
• Control problems, chronic or intermittent.
• Motor problems
• Measurement problems

80
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 Explanation:

1. Turn off and unplug the system from the wall.

WARNING!
Do not plug and unplug connectors with the system power on. This may cause damage to the
connector board and harm to the technician.

2. Visually inspect the connections for excessive debris, moisture, or obvious

damage.
3. Carefully clean any chips away from the connectors.
4. One-by-one, take out each connector and then plug them back in. Do the same
at the computer/display.
5. Make sure to tighten up the screws on each of the connectors.

81
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 Figure 4-1
Electrical Box Schematic
P/N: 20676/20676-1

82
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
Figure 4-2 – Electrical Box Schematic – DPME2

83
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
4.9 External Connector Box – Sport B3 & B5
Indications:
• Control problems, chronic or intermittent.
• Motor problems
• measurement problems

Explanation:
It is often the case that what appears to be the failure of an electrical component is actually
attributable to a poor connection.

1. Turn off and unplug the system from the wall.

CAUTION!
Do not plug and unplug connectors with the system power on. This may cause damage to the
connector board.

2. Visually inspect the connections for excessive debris, moisture, or obvious damage.
3. Carefully clean any chips away from the connectors.
4. One-by-one, take out each connector and then plug them back in. Do the same at the
computer/display. If the connection is sloppy, squeeze the connectors together to make
a better connection.
5. Assure that the ground strap runs from the computer/display to the External connector
box.

The External connector box must be protected from excessive debris or moisture.

4.10 Red LED Diagnostic Status Indicators – DPM/DPM5

(Sport B3/B5 with special electrics option)
There are 12 red LED diagnostic status indicators located on the right side of the relay module.

The meaning of these LED's is as follows (LED 1 is on the top):

1. LED 1 is on when the pendant is switched on. LED 1 also indicates that the computer
module is receiving 115 VAC.
2. LED 2 is on when the E-Stop on the switch box is in the Out position and the overload
relay has not been tripped. LED 2 is on during normal operation.
3. LED 3 is on when the switch box is receiving 115 VAC. LED 3 is on during normal
operation.
4. LED 4 is on when the spindle switch on the switch box is in the 1 or
2 position and the spindle is on.
5. LED 5 is on when the coolant pump is on. The coolant pump can be turned on either by
the switch box or via a CNC auxiliary function.
6. LED 6 is on when the overload relay is tripped. LED 6 is off during normal operation.
7. LED 7 is on when the E-Stop on the switch box is in the Out position. LED 7 is on
during
normal operation.
8. LED 8 flashes on when the Haas rotary table is being indexed one cycle or step. The
function is controlled through Auxiliary Function 3.
9. LED 9 flashes on when the Haas rotary table has completed indexing one cycle or step.
10. LED 10 is on when Auxiliary Function 1 (coolant pump) is on.

84
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 11. LED 11 is on when Auxiliary Function 2 (air relay) is on.
12. LED 12 is on when Auxiliary function (spindle morot) is on.

4.11 Service Codes

All Service Codes are accessed in the SET-UP mode by pressing the “SERV CODES” softkey.
For the EDGE control, SET-UP is accessed through the DRO mode. To access a service code,
press the CODE # softkey, enter the number you want, and press INC SET. Follow the prompts
on your monitor.
Note: If you are working with the SWI Customer Service Group, write the values down for Code
33 or Code 313. These values will be valuable for troubleshooting.
The following table depicts a brief description of all service codes used on the bed mills.
SERVICE
CODE

EDGE
AGE2

AGE3
MX2

MX3
M3

SM

DESCRIPTION
11 X X X X X X Backlash Hysterisis Test (only with X & Y Sensors or Glass Scales)
12 X X X X X X X Determines Feed Forward Constant
13 X X X X X X Sets Default Feed Forward Constant
14 X X Enters Program Scale Factor (0.1 to 10.)
22 X X X X X X Simulation Mode
33 X X X X X X X Software Identification
34 X X X Variable/Fixed Depth Drill Pecking
36 X X X Fast/Slow Pecking
37 X X X X Selects DNC Baud Rate
38 X X X Toggles on/off hard disk / zip drive
54 X X X X X X X Continuous Run Mode
66 X X X X X X X Metric Default; Bytes of ram for CNC2
67 X X X X X X X English Default
68 X X X X X X 0.01 mm (.0005”) Display
69 X X X X X X 0.01 mm (.001")
70 X X X X X X 0.005 mm (0.0001")
79 X X X X X X X Turns on Beeper
80 X X X X X X X Turns off Beeper
81 X X Keyboard Test
89 X X X X X X Out of Simulation Mode
97 X X X X X X Axis Configurationn (dual feedback only)
98 X Sets Default Configuration
99 X X X X X X Master Reset and Clear Program Memory
100 X X X X X X X Axis Open Loop Test
101 X X X X X X-Axis Motor Encoder Test
102 X X X X X Y-Axis Motor Encoder Test
103 X X X Z-Axis Motor Encoder Test
123 X X X X X X X Sensor Calibration Mode – See Section 5.2.2 for details
124 X X Z-Axis Encoder Calibration

85
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
SERVICE
CODE

EDGE
AGE2

AGE3
MX2

MX3
M3

SM
DESCRIPTION
125 X X X X X X Displays Calibration Factors
Single Encoder Axis Backlash Calibration – See Section 5.2.2 for
127 X X X X details
128 X X X X Enters Single Encoder Axis Backlash Calibration Constant
129 X X X X X Enters Arc Accuracy
131 X Manual DRO, Disables Electronic Handwheels
140 X X X X X Irregular Pocket Stepover Distance Adjustments
141 X X X X X X Restores EEPROM From System Disk
142 X X X X X X Saves EEPROM to System Disk
160 X Brightness control
200 X X X Auxiliary Function Test
201 X X X X Displays error codes
202 X X X Enables/Disables Z Jog
304 X Toggles X Sensor or Glass Scale On/Off
305 X Toggles Y Sensor or Glass Scale On/Off
312 X Toggles Limit Switch On/Off
313 X Displays Configuration
314 X Toggles Test Lights 'On' in Status Line
316 X Updates Master Software
317 X Updates Slave Software
318 X Activates Converters or Options
319 X Error Log - Captures All Commands Sent to Servo System
321 X Reverses Y Position Sensor Direction
322 X Reverses X Position Sensor Direction
323 X Switches between COM ports for RS232 applications
324 X Toggles Simulation Mode
325 X Reverses Quill Sensor Direction
326 X Error Message Display
327 X Memory Status
335 X Toggles Spindle On/Off During Pause Events
336 X Enables Spindle to Stay On throughout All Modes
818 X X X X X Displays available memory

86
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
4.11.1 CODE 11: Hysteresis
Note: This code is use only for systems with Sensors or Glass Scales on the table and
saddle.

Code 11 service routine checks the readings of the motor encoder against the sensor
encoder. It is a measurement of how much motor motion is necessary to create table or
saddle motion. This test helps us to look at two things:

• Play: How much backlash must be taken up when motion is reversed.

• Friction: How much the mechanical components must be "torqued up" in order
to break the friction and create motion.
The Code 11 procedure is very useful and will help in diagnosing all types of motion and
performance problems.
1. Position the table and saddle in the center of travel. Note: You will lose your
DRO position reference.
2. Go into the Service Codes and input Code 11.
3. The system will run the checking routine automatically and then display the
values in the position readout.
Explanation:
As an overall measure of the system hysteresis, we are looking for the X and Y values to
be less than .004". A value greater than this indicates a problem with either excessive
friction or play that may affect the finish or accuracy of machined parts.
4.11.2 CODE 12: Feed Forward Constant
The Code 12 procedure helps the control “learn” the friction characteristics of the
machine by sending a graduated series of motor signals and observing the results. The
process takes less than 30 seconds to run. It is both a diagnostic routine that displays
values, and a routine that sets the parameters of the control for the particular machine.

The Code 12 is used for diagnosing and resolving:

• Problems with machine motion.
• Machined parts come out bad – especially poor finish.

Note: Code 12 routine will set the parameters for the particular machine and its
particular situation. If the machine changes its friction characteristic, the Feed Forward
Constant should change too, or the system will not servo properly. Whenever gibs are
adjusted or a heavy workpiece has been added to the table, you should run Code 12.
When the heavy workpiece is removed, run Code 12 again.

1. Position the table and addle in the center of travel. Note: You will lose your
DRO position reference.
2. Go into the Service Codes and input the Code 12.
3. For SM control, press Auto
4. The system will run the routine automatically and then display values on the
position readout.

87
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
Explanation:
Typical values should be between 4.04 and 11.11 are considered normal for each axis.
Higher values indicate excessive friction in the system. Lower values indicate a loose
system and may mean a gib adjustment is necessary. Value 4.04 means the friction is a
factor of 4 in one direction, and 4 in the other direction. The values should be within 3
or 4 of each other in both directions. A value of 6.08 would still be considered normal.

On Sport products, do not equate Code 12 values to torque on ball screw. Measure
friction in system with an in-lb torque wrench.

SM and EDGE only -- The feed forward gain can be adjusted manually by pressing the
manual button. Choose the axis you would like to change and then enter values in the
positive and negative direction to adjust. Adjusting the gain can help solve circularity
problems. Default values can be set by pressing the Reset button. The manual feature
should only be used in extreme cases where the AUTO routine did not solve the
problem. Manual adjusts above 12 may lead to servo related problems.

4.11.3 CODE 33: Software ID

4.11.3.1 EDGE & SM Controls
Code 33 is the software identification procedure. The two types of software in the
control include:
• Software Version - the version of the system you have installed
• Firmware Version - the version of firmware software that is responsible for control
to servo interface.
4.11.3.2 MX, AGE and M3 Controls
The code 33 is the software identification procedure. The two types of software in the
control include:

• Floppy - the version of the system you have installed

• Slave - the version of EPROM software that is responsible for control to servo
interface.
Steps:
1. Go into the Service Codes and input the Code 33.
2. If you are working with the SWI Customer Service Group, write the values down.

Note: Remember that there are two floppy disk drives. The bottom disk drive is
for the system disk.

4.11.4 CODE 97: System Axis Configuration

This procedure sets the Plus and Minus motion for the Motor encoders. It is often
necessary to perform this procedure after a new installation or after installing a new
Computer/Pendant.

Steps:
1. Center the table and saddle and position the quill about halfway down.
2. Go into Service Codes and input Code 97.
3. Very carefully, move the table, the saddle and the quill in the positive direction,
less than 6 inches for each axis. Positive motion is:
• X - table moves to the left ( so the tool moves to the right relative to the
workpiece). + = CW

88
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 • Y - saddle moves toward the front ( so the tool moves up relative to the
workpiece ). + = CCW
• Z - the quill moves up, the ram moves up. The ram and quill must both be
moved in the positive direction. To move the ram, turn the ball screw
manually.

If you do not move correctly from the beginning, repeat the procedure.

4. Press INC SET to signal the procedure is complete.

4.11.5 CODE 100: Axis Open Loop Test

Code 100 procedure is used to diagnose problems with the configuration of the system,
the encoders and incoming A/C voltage.

IMPORTANT -- SAFETY NOTICE

During this procedure the designated axis will be given a command to move at maximum speed
for 1 second in the direction you choose. Avoid crashes by making sure the quill is out of the
way and by starting with the table and saddle centered. MAKE SURE THAT NO ONE IS
STANDING IN THE WAY OF THE TABLE OR SADDLE!
Note: You will lose the DRO reference position.
This procedure is to be run for each axis that is servo-driven and for both the plus and
minus direction for each axis. The following 6 steps apply to all controls. Refer to
Sections 4.11.5.1 through 4.11.5.3 for specific control display data and interpretation.

1. Center the table and saddle and raise the head. Make sure the gib locks are
released.
2. On the Pendant display, go into the Service Codes and input the Code 100.
3. The conversation line will say: “SELECT AXIS”. Input the axis. Either X, Y or Z.
4. In the conversation line it will say “WHICH DIRECTION? PLUS”.
• If you want to run in the plus direction, press INC SET.
• If you want to run in the minus direction, press +/-, then INC SET
5. In the conversation line it will say “PRESS GO”. Press Go after you are sure that
the machine will not crash in the direction and axis that you have specified.
6. Afterward the screen will display values next to the DRO position axes. The
table below assumes machine has secondary feedback. Machines with motor
encoders only will display the reading next to the axis in question.
4.11.5.1 All controls with dual feedback – sensors or glass scale.

Your input Display Data displayed.

X+ X table encoder reading
Y nothing (should be 0)
Z Motor encoder reading
Feedrate the maximum feedrate attained

89
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 Your input X table encoder reading
X- Y nothing (should be 0)
Z motor encoder reading
Feedrate the maximum federate attained.
Your input X nothing (should be 0)
Y+ Y table encoder reading
Z Motor encoder reading
Feedrate the maximum feedrate attained
Your input X nothing (should be 0)
Y- Y table encoder reading
Z Motor encoder reading
Feedrate the maximum feedrate attained

Your input X nothing (should be 0)

Z+ Y nothing (should be 0)
Z motor encoder reading
Feedrate the maximum feedrate attained
Your input X nothing (should be 0)
Z- Y nothing (should be 0)
Z motor encoder reading
Feedrate the maximum feedrate attained
Interpretation of the resulting values displayed:
The values for the encoder displays should be in the range of 3.0000” to 5.0000”.
• If the motor encoder and sensor or glass scale reading is not within this value,
then the one that is out of specification may be the problem. If one of the
encoders is not reading then it will need to be replaced.
• The feedrate should be a minimum of 120 ipm for X and Y-axis, and 180 ipm for
Z. The DPMS3 and DPMS5 should be a minimum of 180 ipm on the X, Y, and Z
axes.
• If the feedrate is less than 180 ipm and inconsistent in both directions, check the
incoming AC voltage and mechanics of the drive train.
4.11.5.2 EDGE Control , SM control, and M control – without feedback.
Your input Display Data displayed.
X+ X motor encoder reading
Y nothing (should be 0 )
Z nothing (should be 0)
Feedrate the maximum feedrate attained

Your input X motor encoder reading

X- Y nothing (should be 0 )
Z nothing (should be 0)
Feedrate the maximum feedrate attained

Your input X nothing (should be 0 )

Y+ Y motor encoder reading
Z nothing (should be 0)
Feedrate the maximum feedrate attained

90
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
 Your input X nothing (should be 0 )
Y- Y motor encoder reading
Z nothing (should be 0)
Feedrate the maximum feedrate attained

Your input X nothing (should be 0 )

Z+ Y nothing (should be 0 )
Z motor encoder reading
Feedrate the maximum feedrate attained
Your input X nothing (should be 0 )
Z- Y nothing (should be 0 )
Z motor encoder reading
Feedrate the maximum feedrate attained

Interpretation of the resulting values displayed:

The values for the encoder displays should be in the range of 3.0000” to 5.0000”.
• If the motor encoder reading is not within this value, then the one that is out of
specification may be the problem. If one of the encoders has no output then the
motor assembly will need to be replaced.
• The feedrate should be a minimum of 120 ipm for X and Y-axis, and 180 ipm for
Z. The DPMS3 and DPMS5 should be a minimum of 180 ipm on the X, Y, and Z
axes.
• If the feedrate is inconsistent in both directions, check the incoming AC voltage
and mechanics of the drive train.

4.11.6 CODE 101: X-Axis Motor Encoder Test

A manual diagnostic routine to compare the motor and position encoders. Used only on
machine with glass scales.

Steps:
1. Go into Service Codes and input 101.
2. Crank the X-axis fast for two inches, then reverse direction and position the X so that
the readout is 1.000".
3. Read the resulting values from the position readout. The chart above (Code 100)
shows the data this is displayed.
The values for the motor encoder and the position encoder should be very close to
each other, within 5% or so. They should also have the same +/- value.
• If they have different values, i.e., + for one and - for the other, perform
Service Code 97.
• If the motor encoder and position encoder is not within 5% of each other,
recalibrate the system. If the problem persists, the motor encoder is
suspected. Note: If the motor encoder is bad, it will be necessary to
replace the entire motor.

91
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
4.11.7 CODE 102: Y-Axis Motor Encoder Test
Manually move the saddle handwheel. See Code 100 above.
4.11.8 CODE 103: Z-Axis Motor Encoder Test
Manually move the quill and ball screw. See Code 100 chart above for displayed values.
4.11.9 CODE 123: Calibration
See Section 5.2.2 for a further explanation of this code.
4.11.10 CODE 127 - Set X or Y Backlash Constant
See Section 5.22 for a further explanation of this code.
4.11.11 CODE 128: Input Backlash Constant
Code 128 allows you to enter the feedback controlers backlash values for each axis. It
displays the value after it enters. This code is used on machines with motor encoders
only, no secondary feedback encoders.

4.11.12 Code 129: Arc Accuracy

When the control operates at high feedrates, it may create small part machining errors
as it goes around sharp corners. This exists on all CNCs and is commonly called a
“following error.” The control is factory preset to allow a maximum following error of
0.001 inch. The feedrate will automatically be adjusted around sharp corners so as to
not violate this limit. This code only applies to arcs that are programmed and ones that
are created in the tool path to generate the shape you want. This code will not make a
difference on mill moves.

You may adjust the maximum following error to a value as small as .0001 inch.
However, the smaller the value, the slower the feedrate around corners.

To input a new Following Error use the following procedure:

Follow the instructions on the screen and input the Following Error value (from .0001 to
.0100) and press INC SET.

4.11.13 Code 314: Toggle Test Lights ‘On’ in Status Line

SM only
This code toggles on and off 2 test lights that appear in status line. The top light
signifies if the master software is working. If functioning it should flash a green light.
The bottom light signifies if the slave firmware is functioning. It will appear orange in
run mode when it is processing information. Pressing the mode key will change this
orange box to black. The orange box will also change to black when the program you
are running reaches the 3rd event from the end of the program. If the firmware is locked
up no keys will work. This code is useful for diagnosing intermittent problems with the
control locking up.
Turn the X, Y, or Z-axis electronic hand wheel. The display should show movement as
the hand wheel is being turned. There should be no skipping and it should count
smoothly while the hand wheel is being turned. One revolution of hand wheel should
read 0.2000”.

4.11.14 Code 319: Error Log – SM only

This code when turned on captures the commands that were sent to the servo system.
It includes items such as positioning commands, errors, stop and go commands, etc. It

92
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
may be helpful for identifying problems between programmed commands and executed
commands. To turn on the error log press the F6 softkey. The page forward and
backward keys allow you to scroll through the file one page at a time. The data forward
and data backward keys allow you to scroll through the file one line at a time. The data
bottom key takes you to the bottom of the file and then changes to data top which will
take you back to the top. The file will capture data until the file reaches a size of
approximately 600 KB. At this time the file is saved to a backup file and the original file
is cleared and data is once again captured. Once again as the file reaches a size of 600
KB it copies over the previous backup file. From here the user can save the file to the
floppy drive by pressing the F8 softkey. Once this in done it prompts you for which file
you want to save to disk. The F1 key saves the current file to disk and the F2 key saves
the backup file to disk. To clear the files press the F7 softkey.

93
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List
5.0 Procedures for Replacements & Maintenance
5.1 Replacements
5.1.1 Servo Motor Replacement

WARNING!
Do not work with the Servo Motors unless the power is disconnected from the machine. The
servomotors are run by 110 VAC. There is possibility of death by electrocution!

1. Turn off power to the machine.

2. Each motor is mounted by the use of (4) ¼-20 screws. Be careful not to over-
tighten these bolts and strip the threads.

5.1.2 Servo Driver Replacement

WARNING!
Do not work with the Servo Drivers unless the power is disconnected from the machine. The
servo drivers are run by 110 VAC. There is possibility of death by electrocution!

The Servo Driver for each axis is integrated into the servo motor casting.

DANGER!
Always engage (push in) the Emergency Stop switch, turn the ProtoTRAK SM Control off, and
disconnect the servo motor/driver cable at the cable breakout box.

1. Press in the Emergency Stop (E-Stop).

2. Remove the servo motor/driver assembly from its mounting bracket (the Y axis
assembly is located inside the front of the bed).

3. Remove the 10 cap screws that hold the servo driver and its heat sink plate to the motor
casting.

4. Disconnect the cable connector. Do not pull on the wires.

5. Reinstall the new servo driver with its heat sink plate. Be certain the gasket
properly seals the assembly.

6. Reinstall the motor/driver assembly. Make certain the belt is tight so that there
is little play if pinched in the middle.

94
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-1
Servo Driver Replacement
Part # Description
20327-2 Z Servo Driver
20201 X & Y Servo Driver

5.1.3 Computer Module Replacement

5.1.3.1Edge 3 Computer Module Replacement
1. Turn off power to the machine and control.
2. Unplug all the connectors on the pendant arm side of the pendant.
3. Remove 2 screws on the right side of the unit and 2 screws on the backside of
the unit. The module is now free to slide toward the right side of the pendant.
4. Slide the computer module a few inches and stop. Pulling the computer module
too far will damage the LCD cable.
5. Now reach from the pendant arm side of the unit and disconnect 3 ribbon cables
from the module.
6. Follow the instructions in reverse order when reinstalling the new computer
module.
7. Make sure the connectors are fully seated before bolting the unit back in place.

95
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-2
Computer Module Replacement – EDGE
5.1.3.2 AGE and MX Computer Module Replacement
The computer module is a black box located inside the computer cabinet, mounted on
the back of the column.

DANGER!
Always unplug power at the back of the display pendant and press in (engage) the Emergency
Stop (E-Stop) before opening the computer cabinet.

1. Turn off power.

2. Unplug the four AC plugs on the bottom of the enclosure.

3. Disconnect the two ribbon cables and ground wire.

4. Unscrew the two silver Philips head screws. The entire module can now slide out
of the cabinet.

5. Sensors and Z ball screw must be recalibrated when the computer module is
replaced.

6. Z backlash must be re-inputted when the computer module is replaced.

96
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.1.3.3 SM3 Computer Module Replacement
1. Turn off power to the machine and control.
2. Unplug all the connectors on the pendant arm side of the pendant.
3. Remove 4 screws on the right side of the unit and 2 screws on the left side of
the unit. The module is now free to slide toward the right side of the pendant.
4. Slide the computer module a few inches and stop. Pulling the computer module
too far will damage the LCD cable.
5. Now reach from the pendant arm side of the unit inside and remove the 37-pin
LCD cable.
6. Now slide the module about ½ way out of the pendant sheet metal.
7. Remove the ground stud from the side of the computer module.
8. Next remove the 37 and 9 pin connectors from the top of the computer module.
9. Lastly slide the unit completely out of the sheet metal.
10. Follow the instructions in reverse order when reinstalling the new computer
module.
11. Make sure the connectors are fully seated before bolting the unit back in place.

Note: if the flash drive is functional, you may want to remove the flash disk and install it in
the new flash drive

Figure 5-3
Computer Module & Flash Drive Replacement – SM3

97
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.1.4 System Flash Disk Replacement (SM3 only)
The system software for the SM control is contained on a 64 MB flash disk that is located
under the door on the right side of the pendant in the upper flash drive slot. If this
needs to be replaced, push the bottom to eject the disk and reload the new disk. Turn
power off to the machine before doing this replacement.

CAUTION!
It is a good idea to back up your flash drive from time to time via a network or floppy disk. If
your flash drive needs to be replaced you will loose all of your programs. See your programming
manual for instruction on how to do this.

5.1.5 Cable Routing on Machine

Whenever you replace a cable or reroute a cable it is very important to keep the power
cables and logic cables separated from each other. The power cables consist of the (3)
110-volt motor cables and (2) 110-volt power cables for the pendant, and a coolant
pump or solenoid power cable. The logic cables are used to carry encoder signals
between the cable breakout box and computer module. Mixing of the power and logic
cables may cause noise from the power cables to interrupt the signals in the logic cables.
This can lead to intermittent axis faults or repeatability problems. See Figures 2-15 for a
layout of the cable connections.

5.1.6 TRAK Sensor Replacement, where applicable

5.1.6.1 Replacing the M5 Base
See Figures 5-4 and 5-5

1. Remove the sensor by removing the clamp screw and then backing the load screw
out a few turns. The sensor should lift off the base easily.
2. Remove the old M5 Base by removing the two 1/4-20 hex head screws that are
threaded into the base.
3. Assemble the new base as per Figure 5-4.
4. Use a bubble level to align the raised bumps on the base with the table for X axis or
saddle ways for Y-axis.
5. A dial indicator may be used to align the bumps on the base instead of a bubble
level.

98
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-4
M5 Base Mounting

5.1.6.2 Replacing the TRAK Sensor

1. Remove the old sensor by removing the clamp screw and then backing the load
screw out a few turns. The sensor should lift off the base easily.
2. Install the new sensor on the M5 base using the clamp screw.
3. Load the sensor against the running surface (table or run bar) using the load screw.
The white lines on the side of the M5 base tell you when it is loaded correctly.

Note: You want to load the gage wheel against the running surface using the flat spring
of the M5 base. Do not tighten the clamp screw fully until after loading the sensor.

99
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-5
TRAK Sensor Mounting

Parts List
Item P/N DESCRIPTION
1 M250C SENSOR - ALL TRAK PRODUCTS
2 M5 M-5 BASE
3 LDCEL-C LOADCELL - M250C
4 M5 HDWR HARDWARE - M5 BASE
5 16023-1 BRACKET-SENSOR X-AXIS
6 21511 EXTENSION
7 24227 BAR-RUN Y-AXIS
8 13777-1 BRACKET-SENSOR Y-AXIS
9 13346-3PK CHIP SCRAPER-M250C
I01160

100
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-6
DPMS3 Sensor Assembly

101
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-7
DPMS5 Sensor Assembly

102
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.1.7 Glass Scale Replacement
5.1.7.1 Remove the X, Y or Z Glass Scale, where applicable
1. Unplug the glass scale connector from the cable breakout box.
2. Unbolt the reader head of the glass scale from its mounting surface.
3. Unbolt the glass scale enclosure from the table on X or the mounting spar on Y.
4. Install the head alignment bracket that came with the replacement scale to this
scale to secure it for shipping back to SWI. Failure to do this may cause the
glass scale to get damaged during shipment. The head alignment bracket
secures the reader head so it cannot move and damage the glass in the scale.

Note: 1st align the reader head on the new scale before removing it to fasten the old
scale.

CAUTION!
Once the head alignment bracket is installed, do not traverse the axis or the
reader head will break.

5.1.7.2 Install the X or Y Replacement Scale

CAUTION!
If the scale is not long enough for the table, it will break when the machine is
traversed past the scale travel.

1. Mount the scale to the back of the table or Y-axis mounting spar.
2. Align the sale so that it is within +/- 0.005" end to end.
Notes: For the Y-axis, the mounting spar should already be aligned. It must be
parallel to the Y-axis travel within +/-.005" end to end both horizontally and
vertically. The mounting spar can be aligned in and out by the use of the adjustment
screw.
3. Line the reader head up with the mounting holes on the back of the saddle for
the X-axis or the bracket on the Y-axis.
4. Install the reader head bolts but leave them loose.
5. Use the jackscrews on the reader head to compensate for some gap between the
reader head and the reader head mounting bracket. Leave the alignment brackets
attached to the reader head. This bracket assures the reader head is aligned to the
glass scale.
6. Tighten each jackscrew until it touches the bracket and then back it off 0.001” or
0.002”. Use a feeler gage to set the gap.
7. Tightening the reader head mounting screws. This ensures the reader head is
aligned within a few thousandths.
8. Remove the shipping bracket that fixes the reader head to the scale for shipping.

103
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 WARNING!
After the reader head is attached to the reader head mounting bracket, do not move
the machine axis until the shipping bracket is removed. This will break the reader
head. This is not covered under warranty.
See Figures 5-8 through 5-10 for an illustration of how to install glass scales.
5.1.7.3 Install the Z-Axis Glass Scale, where applicable (See Figure 5-8)
1. Check the tram of the head in the X direction. If it is within a few thousands
then continue on. If not tram.
2. Assemble Z-axis glass scale mounting bracket and mount to head. Items 1, 2, 3
and 4. Tap items 3 and 4 together and tap item 3 into the quill stop knob.
Leave the bolt loose. Use 2 screws (item 6) and mount item 4 to the side of
item 2 using a spacer between both items to provide a gap of approximately
0.040” between Items 2 and 4. This is to make sure item 2 does not rub against
item 4.
3. Align the glass scale bracket (Item 2) with an indicator and tighten the mounting
screws. Leave the quill stop knob screws loose. Remove the spacer and bolts
from Item 4.
4. Unscrew the shipping protection screw from the scale.
5. Mount the glass scale to the mounting bracket and align it with an indicator. It
needs to be aligned within 0.008" with respect to the quill. Tighten the screws
down.
6. Fasten the readerhead to the readerhead bracket.
7. Move the readerhead up and down the glass scale and make sure the gap is
consistent between the readerhead and the glass scale. Tighten the screw to
the quill stop knob.
8. Remove the red head securing plate.
9. If the gap is not consistent between the readerhead and the glass scale when
moving the quill up and down then adjust the angle of the scale to make the gap
consistent.

WARNING
The gap must be no larger than 0.060” between the readerhead and glass scale.

Part # Description
22800-4 Z Glass Scale

Figure 5-8
Z-Axis Glass Scale Assembly

104
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Item P/N Description Qty
1 20550 ARM- Z-AXIS MOUNTING PLATE 1
2 20551 MOUNTING PLATE-Z-AXIS GLASS SCALE 1
3 20548 ADAPTER-Z-AXIS GLASS SCALE 1
4 20549 ADAPTER PLATE- Z-AXIS GLASS SCALE 1
5 10-32X3/4 25B SCREW-SHCS-STL-BO 4
6 10-32X1 1/4 25B SCREW-SHCS-STL-BO 3
7 15759 WASHER-1/4 HARD BLK OX 1/8 THK 1
8 1/16X1/2 81B SPRING PIN 1
9 1/4-28X3/8 25B SCREW-SHCS-STL-BO 1
11 M4 70B WASHER-FLAT USS-STL-BO 4
12 M4 75J WASHER-EXT TOOTH-SS 4

105
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-9
Glass Scale Alignment – TRM, DPM, Sport B3, DPMS3

106
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Part # Description
22800-42 X Glass Scale
22800-24 Y Glass Scale

Figure 5-10
Glass Scale Alignment – DPM5, Sport B5, DPMS5
107
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.1.8 Power Drawbar – Optional for DPME2, DPMS3 and DPMS5
The optional power drawbar is bolted to the top of the head by the use of 3 SHCS.
Some machines may require a washer to space the unit up to the proper height to allow
the drawbar to engage properly.

Air Regulator and Oiler - This unit requires between 80 and 100 psi to operate
properly. Some units work fine at 80 psi while others may need 90 or 100 psi. It is also
important to make sure the oiler for this unit is kept filled with oil. Fill the reservoir
about 2/3 full using AIR TOOL OIL ONLY. Failure to do this will not allow oil to lubricate
the internal components of the unit and it may wear out prematurely. It is also
important to make sure the oiler is set properly. To set the oiler, first close the
adjustment screw (CW) on top of the oiler completely making sure to not over tighten.
Then open the screw (CCW) between ½ to ¾ of a turn. Any more than this will cause
too much oil to get into the unit and oil may come out of the exhaust port of the unit.

DPMS3 & DPMS5 only: Tool Alignment Device - This unit also comes with a tool
alignment device, which attaches to the bottom of the spindle. This device allows the
tool to easily be aligned with the dogs when loading a tool.

CAUTION!
Some tools may not work with this device and the original spindle dogs will need to be
used. The original spindle dogs are shipped with each machine in the toolbox. Some
boring bar holders may not work with this device.

108
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-11
Power Drawbar Assembly

109
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List

Item P/N DESCRIPTION

1 22581-1 AIR GUN ASSY ONLY- TORQUE RITE
2 See table below DRAWBAR
3 See table below TOP WASHER
4 22380-2 AIR REGULATOR ASSY
5 See table below DRAWBAR
6 22581-2 SWITCH - CONTROL HEAD - TORQUE RITE
7 22581-4 NOSEPIECE FOR SPINDLE
8 -- 1/4" NPT AIR FITTING 90°
9 -- 3/8 O.D. TUBING 132" LG.
10 -- 3/8 O.D. TUBING 27" LG.
11 See table below DRAWBAR
12 See table below DRAWBAR
13 See table below DRAWBAR
i01131

Drawbar Table

Model Mill Power Drawbar Power Drawbar Manual Drawbar Manual Drawbar
Spacer Spacer

DPME2 22605 22604 VS09 V5108

DPMS3/B3/TRM/DPM 22603-NMTB 21661 AK147L AK149L

DPMS3/B3/TRM/DPM 22603-CAT 21661 AK147L AK149L

DPMS5/B5 22641-NMTB 23888 FVS109 FVS108

DPMS5/B5 22641-CAT 23888 FVS109 FVS108

110
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
5.1.9 Ball Screw Replacement, X-Axis (Table)
Refer to the following chart for illustrations and parts lists of the X-axis drive
assembly for each model.

X-axis Drive Train

Machine Model Figure Ballscrew P/N
TRM 5-12 15608-48*
DPM 5-12 15608-48
DPM5 5-14 21564
Sport B3 5-12, 5-13 15608-48
Sport B5 5-14 21564
DPMS3 5-15 15608-48
DPMS5 5-16, 5-17 21564
DPME2 5-18 15608-48

*Early MX2TRM may have 42” table/ballscrews.

CAUTION!
Never screw a ball screw partially or totally out of its nut. They cannot be reassembled.

1. Position the table in the center of travel

2. Remove the X motor assembly.
3. Remove the motor mounting bracket and bearing housing.
4. Remove the right side bearing housing.
5. TRM & DPM only: Remove X-axis sensor guard cover and X TRAK sensor from its mounting
base.
6. Loosen the table gibs. Slide the table to the right and on to a lift that will support the
table's weight. Slide the table until the yoke is exposed.

CAUTION!
The weight of the table must be supported by the lift to prevent damage or
breakage to the dovetails.

7. Remove the 5/16 x 1" screw holding the ball nut to the yoke and loosen the 4 screws
that mount the yoke to the saddle. Remove the oil line.
8. Remove the Y-axis motor and bracket assembly. Tilt the yoke (it is pinned) to
remove the X ball screw.
9. Remove the elbow and setscrew from the old ball screw flange and fit them similarly
in the new ball screw.
10. Pump oil to be certain it flows through the oil line and then attach the oil line to the elbow.
11. Reassemble all assemblies.

Important: The clamp nut must be reassembled as follows:

• Install rear bearing and seal into bearing housing and slide housing onto the ball
screw. (Note: Letters on bearings must face each other in the housing.)

111
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 • Thread the split nut onto the ball screw and tighten the #10-32 clamp screw until
you feel the split nut contact the ball screw threads. It should drag as you tighten
the clamp nut.
• Torque the split nut to 50 ft. lb.
• Firmly tighten the #10-32 clamp screw to lock the clamp nut in place.

See the diagnostics section under Mechanical Drive Train for an explanation of how to
align the ball screw.

5.1.9.1 X-Axis Handwheel Box – DPMS5 only

(See Figure 5-17)
Teardown and Part Replacement
1. Remove top sheet metal cover (item #2).
2. Remove the manual hand wheel.
3. Release back cover hub (item #4).
4. Slide cover hub and shaft assembly (items # 12,3,9, and 4) out.
4.a. Shaft assembly removal
4.a.1. Slide shaft assembly (item #12, and # 3) off of back cover hub
assembly (item #9 and #4).
4.a.2. Loosen setscrew (item #14)
4.a.3. Slide shaft gear off (item #12)
4.a.4. Remove key (item #13)
5. Remove front hub assembly (item #5) from hand wheel box.
6. Remove gear (item # 11) at the end of the ball screw.
6.a. Remove extension cover (item #8), use Allen wrench on item #14 to help
support ball screw from rotating, and back out the extension cover support
screw.
6.b. Loosen setscrew (item #14)
6.c. Slide Left Gear out
6.d. Remove key (item #13)
7. Remove hand wheel box (item #1)
8. Remove ball screw extension (item #7)
8.a. back out setscrews (item #14)
8.b. back off extension by sliding a 3/16" Allen wrench through thru hole,
pushing it up against the end of the ball screw pushing the extension slightly
away from the bearing.
8.c. Using two large screwdrivers pushing off the saddle, slide the extension off.
9. Use a mechanical puller to remove the bearing

Re-Assembly of Handwheel Box

1. Slide bearing on to the end of the ball screw (item #9), use a socket or piece of
aluminum tubing and a dead blow hammer to tap bearing till it flushes up
against the step of the ball screw.
2. Slide the extension on and flush it up against the bearing, lock down with both
setscrews (item #14). Item 19 can be used to push the extension from the end
of the ball screw to adjust the gear spacing.
3. Bolt the handwheel box (item # 1) down.
4. Bolt the front hub assembly (items #6, 10, and 5) on.
5. Slide the shaft assembly (items # 3, 12, 9, and 4) in through the backside and
bolt the cover hub on.

112
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 CAUTION!
Assemble the hand wheel, move it back and forth, and see if there is some play in
meshing the two gears together. If the gears mesh tightly against one another it
can generate noise during movement of the X-axis. It is normal to have a small
amount of backlash between the gears.

6. Screw on top cover.

Parts List - X Drive Assembly - TRM, DPM & Sport B3

NO. P/N DESCRIPTION QTY
1 15974 END PLATE 1
2 15973 ADAPTER SERVO MOTOR 1

9 15638 STOP "X" AXIS 1

12 14772 SPACER 4
15 15613 CLAMP NUT 1
16 400-5M-15 BELT - TIMING 5 MM HTD 1
17 15612 HOUSING - BEARING 1
18 20373 BEARING - ANG CONTACT 2
19 15885 RING - BEARING 1
20 15626 SEAL 1
23 15616 HANDWHEEL - ASSY 1
25 15180 SHAFT EXTENSION 1
26 15058-.875 BUSHING - EXTENSION 1
29 15976 TRAY (C15976) 1
30 15977 FLAT RIB RUBBER MATING - PAO McMASTER CARR # 6972T3 1
31 204KTT BALL BEARING 1
33 10-32x3/4 SCREW - SOC HD CAP STL BLK OX 1
34 14772-5 SPACER - .005 3
35 14772-2 SPACER - .02 1
36 16865-1 PULLEY - SOLID 44 TOOTH 1
37 16864 SLEEVE - TAPERED 1

113
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-12
X Drive Assembly for
TRM, DPM & Sport B3

114
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-13
X Drive Assembly,
Left Side – DPME2

115
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-14
X-Drive Assembly – DPM5 & Sport B5DD

116
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List, X Drive Assembly - DPM5 & Sport B5

NO. P/N DESCRIPTION QTY

1 21685 MOTOR DRIVER ASSY- REF
3 15966-2 BRACKET- MOTOR MOUNT 1
4 15967-2 COVER- UPPER 1
5 15968-2 COVER- LOWER 1
6 21585-2 COVER- BALL SCREW END 1
7 21573 BEARING HOUSING- REF
8 21572 COVER- BALL SCREW END REF
10 21584-2 END COVER PLATE 1
11 6-32 x 1/2 10B SCREW- PAN HD, EXT SEMS, STL, BLK OX 9
13 98481A090 KEY- WOODRUFF 1/8 x 1/2 1
15 16066 CLAMP NUT 1
16 565-5M-15 BELT - TIMING 5 MM HTD 1
17 21662 BEARING HOUSING- X AXIS 1
18 20374 BEARING - ANG CONTACT 2
19 16302 RING - BEARING 1
20 16078 SEAL 1
25 M8-1.25 x 25 25B SCREW- SOC HD CAP, BLK OZ 4
26 M8 74B WASHER- EXTERNAL TOOTH 4
27 1/4-20 x 1 24B SCREW- HEX HD 4
28 15759 WASHER- FLAT 1/4 4
29 M10-1.5 x 40 25B SCREW- SOC HD CAP, BLK OX REF
30 M6-1.0 x 10 25B SCREW- SOC HD CAP, BLK OX REF
31 6205 BALL BEARING- DEEP GROOVE REF
33 10-32 x 3/4 25B SCREW- SOC HD CAP, BLK OX 1
36 16983-1 PULLEY - SOLID 44 TOOTH 1
37 16350 SLEEVE - TAPERED 1
38 1/2 WASHER- FLAT 1/4 1
39 91079A033 NUT- JAM 1/2-20 51Z 1
40 1/2 75C WASHER- EXT TOOTH 1
41 M10-1.5 x 65 SCREW- SOC HD CAP, BLK OX 4

117
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-15 X-Axis Drive
Assembly – DPMS3

118
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
DPMS3 X-Axis Drive Assembly Parts List
Item P/N Description Qty
1 15974 END PLATE 1
2 15973 SERVO MOTOR ADAPTER 1
4 M10-1.5X30 25B SCREW-SHCS-STL-BO 8
5 15614 TAB WASHER 1
6 15759 WASHER-1/4 HARD BLK OX 1/8 THK 11
8 1/4-20X1 24B SCREW-HEX HD-STL-BO 8
9 15638 STOP - X-AXIS 1
10 1/2-20 51Z NUT-HEX JAM-STL-ZINC 2
11 1/2 70P WASHER-FLAT USS-STL-PLAIN 1
12 14772 SPACER - .100" THICK 4
15 16452 NUT CLAMP-X, Y, & Z AXIS 1
16 425-5M-15 BELT-TIMING 5 MM POWERGRIP 1
17 15612 HOUSING - BEARING 1
18 20373 BEARING-ANGULAR CONTACT- 7204 BECBP 2
19 15885 RING-BEARING HOUSING 1
20 15626 SEAL-BEARING HOUSING 1
21 1/4-20X3/4 25B SCREW-SHCS-STL-BO 3
22 5/16-18X1 1/4 25B SCREW-SHCS-STL-BO 1
23 15616 HANDWHEEL ASSY-MX 1
24 1/2 75Z WASHER-EXT TOOTH-STL-ZINC 1
25 15180 SHAFT-EXTENSION 1" 1
26 15058-.875 BUSHING 1
28 1/4-28X1 43B SCREW-SOC SET-STL-BO-KNURLED 1
29 22069 TRAY MACHINE 1
30 15977 TRAY PAD 1
31 22008 BEARING-204KTT 1
32 1/4-28X3/4 42B SCREW-SOC SET-STL-BO-CONE 1
33 10-32X3/4 25B SCREW-SHCS-STL-BO 1
34 14772-5 SPACER - .050" THICK 3
35 14772-2 SPACER - .020" THICK 1
36 16983-1 PULLEY-SOLID 44 TEETH W/O GUIDES 1
37 16350 FERRULE-SPROCKET 1
38 98481A090 KEY WOODRUFF #404-1/8 X 1/2 1
i00771-X-S3

119
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-16 X Drive Train – DPMS5

120
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
DPMS5 X Drive Train Parts List
Item P/N Description Qty
3 15966 BRACKET-Y AXIS MOTOR MOUNT 1
4 15967 COVER-UPPER 1
5 15968 COVER-LOWER 1
6 21585-1 COVER-BALL SCREW END 1
10 21584-1 PLATE-END COVER 1
11 6-32X1/2 10B SCREW-PH-PHIL-STL-BO 9
13 98481A090 KEY WOODRUFF #404-1/8 X 1/2 1
15 16066 NUT CLAMP-X & Y AXIS 1
16 600-5M-15 BELT-TIMING 1
17 21662 BEARING HOUSING- 1
18 20374 BEARING-ANGULAR CONTACT-7205 BECBP 2
19 16302 RING-BEARING HOUSING 1
20 16078 SEAL-BEARING HOUSING 1
22 M10-1.5 50P NUT-HEX-STL-PLAIN 2
23 M10 73B WASHER-SPLIT LOCK-STL-BO 2
25 M8-1.25X25 SCREW-SHCS-STL-BO 4
25B
26 M8 74B WASHER-EXT TOOTH-STL-BO 4
27 1/4-20X1 24B SCREW-HEX HD-STL-BO 4
28 15759 WASHER-1/4 HARD BLK OX 1/8 THK 4
33 10-32X3/4 25B SCREW-SHCS-STL-BO 1
36 16983-1 PULLEY-SOLID 44 TEETH W/O GUIDES 1
37 16350 FERRULE-SPROCKET 1
38 1/2 70P WASHER-FLAT USS-STL-PLAIN 2
39 1/2-20 51Z NUT-HEX JAM-STL-ZINC 2
40 1/2 75Z WASHER-EXT TOOTH-STL-ZINC 2
41 M10-1.5X75 SCREW-SHCS-STL-BO-FULLY THD 8
25B
42 15616 HANDWHEEL ASSY-MX 1
43 15614 TAB WASHER 1
i00771-X-S5

121
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-17 X Handwheel Drive Mechanism – DPMS5 only

122
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 X Handwheel Drive Mechanism Parts List – DPMS5 only
P/N 23021 – Gear Box Assembly

Item P/N Description Qty

1 23014 HANDWHEEL BOX-X AXIS 1
2 23015 SHEET METAL-PT4-COVER-X AXIS-HANDWHEEL BOX 1
3 23019 SHAFT-X AXIS-HANDWHEEL BOX 1
4 23017 COVER-HUB-X AXIS-HANDWHEEL BOX 1
5 23018 HUB-X AXIS-HANDWHEEL BOX 1
6 23020 COVER-X AXIS-HANDWHEEL BOX 1
7 23027 EXTENSION-BALL SCREW-X AXIS-HANDWHEEL ASSY 1
8 23028 COVER-EXTENSION-BALL SCREW-X AXIS-HANDWHEEL 1
ASSY
9 6205ZZ BEARING-DEEP GROOVE 2
10 6204ZZ BEARING- 1
11 23033-L GEAR-HARDENED STEEL SPIRAL MITER-LEFT 1
12 23033-R GEAR-HARDENED STEEL SPIRAL MITER-RIGHT 1
13 3/16X1 KEY-3/16X1 2
14 1/4-20X1/2 SCREW-SOC SET-STL-BO-CUP 6
40B
15 1/4-20X3/4 SCREW-SHCS-STL-BO 6
25B
16 1/4-28X1 1/4 SCREW-SHCS-STL-BO 3
25B
17 1/4-20X1/2 SCREW-BHCS-STL-BO 4
27B
18 1/4-20X5/8 SCREW-FHCS-STL-BO 1
26B
19 1/4-20X3/4 SCREW-SOC SET-STL-BO-CUP 1
40B

123
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-18 X-Axis Drive
Assembly – DPME2

124
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
X-Axis Drive Assembly Parts List – DPME2
Item P/N Description Use As Qty
1 15621 DRIVE HOUSING EA 1
4 15624 FRONT COVER EA 1
5 15622 BACK COVER EA 1
6 15616 HANDWHEEL ASSY-MX EA 1
7 15614 TAB WASHER EA 1
8 15612 HOUSING - BEARING EA 1
9 15885 RING-BEARING HOUSING EA 1
10 15638 STOP - X-AXIS EA 1
11 15626 SEAL-BEARING HOUSING EA 1
12 16983-1 PULLEY-SOLID 44 TEETH W/O GUIDES EA 1
13 16452 NUT CLAMP-X, Y, & Z AXIS EA 1
14 16350 FERRULE-SPROCKET EA 1
15 98481A090 KEY WOODRUFF #404-1/8 X 1/2 EA 1
16 14772 SPACER - .100" THICK EA 5
19 400-5M-15 BELT - TIMING 5 MM POWERGRIP EA 1
20 20373 BEARING-ANGULAR CONTACT- 7204 BECBP EA 2
22 14772-2 SPACER - .020" THICK EA 2
23 14772-5 SPACER - .050" THICK EA 2
41 8-32X3/8 25B SCREW-SHCS-STL-BO EA 6
42 5/16-18X1 25B SCREW-SHCS-STL-BO EA 1
45 M10-1.5X65 25B SCREW-SHCS-STL-BO EA 4
46 1/4-20X1 24B SCREW-HEX HD-STL-BO EA 7
47 8-32X3/8 20B SCREW-RH-PHIL-STL-BO EA 3
48 10-32X3/4 25B SCREW-SHCS-STL-BO EA 1
49 1/2-20 51Z NUT-HEX JAM-STL-ZINC EA 2
52 15759 WASHER-1/4 HARD BLK OX 1/8 THK EA 7
54 M10 70P WASHER-FLAT USS-STL-PLAIN EA 4
55 1/2 73B WASHER-SPLIT LOCK-STL-BO EA 1
56 1/2 70P WASHER-FLAT USS-STL-PLAIN EA 1
i20255-2

125
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.1.10 Ball Screw Replacement, Y-Axis (Saddle)
Refer to the following chart for illustrations and parts lists of the Y-axis drive assembly
for each model.

Y-axis Drive Train

Machine Model Figure Ballscrew P/N
TRM 5-19, 5-20 15609-16
DPM 5-19, 5-20 15609-16
DPM5 5-21 21564
Sport B3 5-22 15609-16
Sport B5 5-21 21564
DPMS3 5-23 15609-16
DPMS5 5-24 21564
DPME2 5-25 15609-16

CAUTION!
Never screw a ball screw partially or totally out of its nut. They cannot be reassembled.

1. Position the saddle all the way forward.

2. Remove the hand wheel assembly and bracket.
3. Remove the sheet metal covers on the front of the machine bed and on the
motor mounting bracket.
4. Remove the motor, then remove the motor mounting bracket.
5. Remove the rest of the parts on the ball screw journal. Note the orientation of
the bearings for reassembly.
6. Remove the 5/16 x 1 inch screw that attaches the ball nut to the yoke.
7. Remove the ball screw and oil line attached to the elbow fitting on the ball nut.
8. Remove the elbow and setscrew from the old ball screw flange and fit them
similarly in the new ball screw.
9. Pump oil to be certain it flows through the oil line, and then attach the oil line to the
elbow.
10. Reassemble all assemblies.
Important: The clamp nut must be reassembled as follows:
• Install rear bearing and seal into bearing housing and slide housing onto the
ball screw. (Note: Letters on bearings must face each other in the housing.)
• Thread the split nut onto the ball screw and tighten the #10-32 clamp screw until
you feel the split nut contact the ball screw threads. It should drag as you tighten
the clamp nut.
• Torque the split nut to 50 ft. lb.
• Firmly tighten the #10-32 clamp screw to lock the clamp nut in place.

See the diagnostics section under Mechanical Drive Train for an explanation of how to
align the ball screw.
126
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-19
Ball Screw
Yoke Assembly – P/N 15990
TRM & DPM

127
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-20 Y Drive Assembly –
TRM & DPM

128
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Y Drive Assembly Parts List - TRM & DPM

Item P/N Description Qty

1 15966 BRACKET-Y AXIS MOTOR MOUNT 1
3 15968 COVER-LOWER 1
4 15967 COVER-UPPER 1
9 15616 HANDWHEEL ASSY-MX 1
12 15614 TAB WASHER 1
13 14772 SPACER - .100" THICK 1
14 15980 BEARING HOUSING 1
15 20373 BEARING-ANGULAR CONTACT- 7204 BECBP 2
16 15885 RING-BEARING HOUSING 1
17 15626 SEAL-BEARING HOUSING 1
19 20195-2 SLIP CLUTCH ASSY 125 LBS-INCH 1
20 15613 CLAMP NUT-BEARING HOUSING 1
21 565-5M-15 BELT-TIMING 1
22 15627-1 DIAL HOLDER 1
23 15913 BRACKET-WAY COVER FRONT 1

129
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-21 Y Drive Assembly – DPM5 & Sport B5

130
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List, Y Drive Assembly – DPM5 & Sport B5
NO. P/N DESCRIPTION QTY
1 15966-2 BRACKET - MOTOR MOUNT 1
2 15967-2 COVER - UPPER 1
3 15968-2 COVER - LOWER 1
4 21662 BEARING HOUSING 1
5 16302 BEARING RING 1
6 16078 SEAL - BEARING 1
7 16983-1 PULLEY - 44 TOOTH 1
8 16066 NUT - CLAMP 1
9 16350 SLEEVE - TAPERED 1
10 21685 MOTOR DRIVER ASSY- REF
11 15913-2 COVER- UPPER 1
13 M8-1.25 x 25 SCREW- SOC HD CAP BLK OX 4
14 565-5M-15 TIMING BELT 1
15 20374 BEARING 2
16 M8 74B WASHER EXTERNAL TOOTH 4
17 M10-1.5 X 65 SCREW - SOC HD CAP, BLK OX 4
18 10-32 x 3/4 25B SCREW - SOC HD CAP, BLK OX 1
19 1/4-20 x 1 24B SCREW - HEX HEAD 4
20 15759 WASHER- FLAT 1/4 4
23 91079A033 NUT - JAM, ZINC PLATE, 1/2-20 1
24 1/2 70Z WASHER - FLAT, STL, ZINC 1
25 1/2 75C WASHER- EXT TOOTH 1
28 3/16 x 1 1/2 PIN - SPRING, STL, PLAIN 2
29 21584-2 END COVER PLATE 1
30 21585-2 END COVER- BALL SCREW 1
31 6-32 x 1/2 10B SCREW- PAN HD PHIL EXT SEMS 9
32 98481A090 KEY- WOODRUFF 1/8 x 1/2 1

131
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-22
Y Drive Assembly – Sport B3

132
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Y Drive Assembly Parts List - Sport B3

ITEM P/N DESCRIPTION QTY

1 15966-2 BRACKET - MOTOR MOUNT 1
11 15967-2 COVER - UPPER 1
14 15968-2 COVER - LOWER 1
17 15980 BEARING HOUSING 1
18 15885 BEARING RING 1
19 15626 SEAL - BEARING 1
20 16865-2 SPROCKET - 44 TOOTH 1
21 15613 NUT - CLAMP 1
22 16864 SLEEVE - TAPERED SPRO.
23 15836 DIAL NUT 1
24 15616-1 HANDWHEEL 1
25 15614 WASHER - TAB 1
27 15627-1 DIAL HOLDER 1
32 565-5M-15 TIMING BELT 1
35 20373 BEARING 2
37 14772 SPACER 2
41 M10-1.5 X 60 SCREW - SOC HD CAP, BLK OX 4
10-32 x 3/4 SCREW - SOC HD CAP, BLK OX 4
45 1/4-20 x 1 SCREW - HEX HEAD 4
47 6-32 x 3/8 SCREW - FLAT HEAD, BLK OX 12
49 91079A033 NUT - JAM, ZINC PLATE, 1/2-20 1
52 1/2 DIA WASHER - FLAT 1
53 M10 WASHER - FLAT 4
57 1/4 DIA (15759) WASHER - FLAT 4
62 30922 FOLD-AWAY HANDLE 1

133
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-23 Y Drive
Train – DPMS3

134
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Y Drive Train Parts List – DPMS3

Item P/N Description Qty

1 15966 BRACKET-Y AXIS MOTOR MOUNT 1
2 M10-1.5X60 25B SCREW-SHCS-STL-BO 4
3 15968 COVER-LOWER 1
4 15967 COVER-UPPER 1
5 6-32X3/8 31Z SCREW-PH-PHIL-EXT SEMS-STL-ZINC 8
7 1/2 70P WASHER-FLAT USS-STL-PLAIN 1
9 15616 HANDWHEEL ASSY-MX 1
10 1/2 75Z WASHER-EXT TOOTH-STL-ZINC 1
11 1/2-20 51Z NUT-HEX JAM-STL-ZINC 1
12 15614 TAB WASHER 1
13 14772 SPACER - .100" THICK 1
14 15980 BEARING HOUSING 1
15 20373 BEARING-ANGULAR CONTACT- 7204 BECBP 2
16 15885 RING-BEARING HOUSING 1
17 15626 SEAL-BEARING HOUSING 1
18 16350 FERRULE-SPROCKET 1
19 16983-1 PULLEY-SOLID 44 TEETH W/O GUIDES 1
20 16452 NUT CLAMP-X, Y, & Z AXIS 1
21 600-5M-15 BELT-TIMING 1
22 15627-1 DIAL HOLDER 1
23 15913 BRACKET-WAY COVER FRONT 1
27 10-32X3/4 25B SCREW-SHCS-STL-BO 1
28 1/4-20X1 24B SCREW-HEX HD-STL-BO 4
29 15759 WASHER-1/4 HARD BLK OX 1/8 THK 4
30 98481A090 KEY WOODRUFF #404-1/8 X 1/2 1
i00771-Y-S3

135
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-24 Y Drive Train –
DPMS5

136
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Y Drive Train Parts List – DPMS5

Item P/N Description Qty

1 15966 BRACKET-Y AXIS MOTOR MOUNT 1
2 15967 COVER-UPPER 1
3 15968 COVER-LOWER 1
4 21662 BEARING HOUSING- 1
5 16302 RING-BEARING HOUSING 1
6 16078 SEAL-BEARING HOUSING 1
7 23026 PULLEY-SOLID 44 TEETH 1
8 16066 NUT CLAMP-X & Y AXIS 1
9 16350 FERRULE-SPROCKET 1
11 15913 BRACKET-WAY COVER FRONT 1
13 M8-1.25X25 25B SCREW-SHCS-STL-BO 4
14 600-5M-15 BELT-TIMING 1
15 20374 BEARING-ANGULAR CONTACT-7205 BECBP 2
16 M8 74B WASHER-EXT TOOTH-STL-BO 4
17 M10-1.5X65 25B SCREW-SHCS-STL-BO 4
18 10-32X3/4 25B SCREW-SHCS-STL-BO 1
19 1/4-20X1 24B SCREW-HEX HD-STL-BO 4
20 15759 WASHER-1/4 HARD BLK OX 1/8 THK 4
23 1/2-20 51Z NUT-HEX JAM-STL-ZINC 2
24 1/2 70P WASHER-FLAT USS-STL-PLAIN 2
25 1/2 75Z WASHER-EXT TOOTH-STL-ZINC 2
28 3/16X1 1/2 81P PIN-SPRING-STL-PLAIN 2
31 6-32X1/2 10B SCREW-PH-PHIL-STL-BO 8
32 98481A090 KEY WOODRUFF #404-1/8 X 1/2 1
33 15616 HANDWHEEL ASSY-MX 1
34 23016 EXTENSION-BALL SCREW-Y AXIS-HANDWHEEL ASSY 1
35 1/4-20X1 3/4 25B SCREW-SHCS-STL-BO 3
36 15614 TAB WASHER 1
i00771-Y-S5

137
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-25 Y Drive
Train – DPME2

138
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Y Drive Train Parts List – DPME2

Item P/N Description Use As Qty

1 15966-3 BRACKET-Y AXIS MOTOR MOUNT EA 1
2 M10-1.5X60 25B SCREW-SHCS-STL-BO EA 4
3 15968-2 LOWER COVER EA 1
4 15967-2 UPPER COVER EA 1
5 6-32X3/8 31Z SCREW-PH-PHIL-EXT SEMS-STL-ZINC EA 8
7 1/2 70P WASHER-FLAT USS-STL-PLAIN EA 1
9 15616 HANDWHEEL ASSY-MX EA 1
10 1/2 75Z WASHER-EXT TOOTH-STL-ZINC EA 1
11 1/2-20 51Z NUT-HEX JAM-STL-ZINC EA 1
12 15614 TAB WASHER EA 1
13 14772 SPACER - .100" THICK EA 1
14 15980 BEARING HOUSING EA 1
15 20373 BEARING-ANGULAR CONTACT- 7204 BECBP EA 2
16 15885 RING-BEARING HOUSING EA 1
17 15626 SEAL-BEARING HOUSING EA 1
18 16350 FERRULE-SPROCKET EA 1
19 16983-1 PULLEY-SOLID 44 TEETH W/O GUIDES EA 1
20 16452 NUT CLAMP-X, Y, & Z AXIS EA 1
21 500-5M-15 TIMING BELT EA 1
22 15627-1 DIAL HOLDER EA 1
27 10-32X3/4 25B SCREW-SHCS-STL-BO EA 1
28 1/4-20X1 24B SCREW-HEX HD-STL-BO EA 4
29 15759 WASHER-1/4 HARD BLK OX 1/8 THK EA 4
30 98481A090 KEY WOODRUFF #404-1/8 X 1/2 EA 1
31 15836 DIAL NUT EA 1
32 M5-0.8X10 10Z SCREW-PH-PHIL-STL-ZINC EA 2
i23158-2

139
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.1.11 Z-Axis Ball Screw Removal & Replacement
Refer to the following chart for illustrations and parts lists of the Z-axis
drive assembly for each model.

Z-axis Drive Train

Machine Model Figure Ballscrew P/N
TRM N/A B004
DPM 5-26 16806-m
DPM5 5-26 16806-m
Sport B3 5-26 16806-m
Sport B5 5-26 16806-m
DPMS3 5-27 16806-m
DPMS5 5-27 16806-m
DPME2 5-28 23662

CAUTION!
Never screw a ball screw partially or totally out of its nut. They cannot be reassembled.

1. Ensure that there is sufficient vertical clearance above the top of the machine to
remove the ball screw. Minimum clearance required is 32 inches.
2. Remove vertical column top cover.
3. Remove servomotor, belt and Z motor mounting bracket.
4. Remove upper and lower Z-axis way covers.
5. Lower head to table. Place 1 or 2 inch wood board between spindle nose and table to
protect.
6. Lower head until weight of head is supported by the table.
7. Tighten both ram locks on the right side of ram.
8. Remove locknut and lock washer from the top of the Z ball screw.
9. Remove pulley and woodruff key.
10. Loosen #10-32 socket screw on clamp nut.
11. Using wrench flats on clamp nut and wrench flats on ball screw remove clamp
nut.
12. Remove the four cap screws from bearing housing flange.
13. Remove the clamp nut.
14. Remove bearing, nilos ring and bearing housing with matched spacer from ball
screw.
15. Remove (6) M6 cap screws and lock washers from ball nut flange.
16. Extract ball screw assembly from machine until ball nut flange is above the top of
the ram. Support ball screw and remove lubrication line from ball nut flange.

140
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 17. Raise the ball screw until the bottom end of the ball screw is above the ram.
Angle the ball screw out and away from the head. Lower the ball screw on the
right side of the machine until the top of the ball screw clears the support plate.
18. Reassemble all components in reverse order as shown above, except leave off
the pulley, locknut and lock washer until ball screw is realigned. Torque clamp
nut to 50 ft. lb.
19. With the ball screw assembly installed, loosen four 5/16-18 cap screws from
bearing housing, raise head to the uppermost position, and re-tighten 5/16-18
cap screws. Note that there is .060 clearance between the bearing housing
outside diameter and the inside diameter of the support plate to allow for
realignment. Traverse the head to the extreme of the up and down travel
manually to check for freedom of movement. Use torque wrench to make sure
torque is consistent along length of screw. Use torque wrench to make sure
torque is consistent along length of screw.

See Section 5.2.2 to properly measure and set the Z Backlash Compensation and
calibration.

141
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-26
Z Axis Motor and
Ball Screw –
DPM, DPM5, Sport B3
& Sport B5

142
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List – Z Axis Motor and Ball Screw
DPM, DPM5, Sport B3 & Sport B5

Item P/N Description Use Qty

As
1 16806-M BALL SCREW ASSY- Z-AXIS EA 1
2 PJ540015 BRACKET LOWER ELEVATING BALL SCREW EA 1
3 2205E-2RS1TN9 BEARING SELF ALIGNMENT SKF EA 1
4 16774 COVER - BEARING EA 1
5 16795 MODIFIED BEVEL GEAR BS1236-2A EA 1
6 M10-1.5X10 40B SCREW-SOC SET-STL-BO-CUP EA 1
7 16770 MODIFICATION OF 3 HP RAM PING JENG PART EA 1
8 M6 73B WASHER-SPLIT LOCK-STL-BO EA 6
9 M6-1.0X25 25B SCREW-SHCS-STL-BO EA 6
10 7205-AVH NILOS RING-7205 EA 1
11 16295-1 HOUSING- BEARING Z-AXIS EA 1
12 16302 RING-BEARING HOUSING EA 1
13 20374 BEARING-ANGULAR CONTACT-7205 BECBP EA 2
14 16773 CLAMP NUT EA 1
15 10-32X3/4 25B SCREW-SHCS-STL-BO EA 1
16 16350 FERRULE-SPROCKET EA 1
17 16983 PULLEY-SOLID 44 TEETH Z-AXIS EA 1
18 N01 LOCKNUT EA 1
19 W01 LOCKWASHER EA 1
20 M8 73B WASHER-SPLIT LOCK-STL-BO EA 4
21 98481A090 KEY WOODRUFF #3-1/8 X 1/2 EA 1
22 M8-1.25X20 25B SCREW-SHCS-STL-BO EA 4
23 710-5M-15 BELT - TIMING EA 1
24 16771 PLATE- Z AXIS SUPPORT EA 1
25 1/4-20X1 1/4 25B SCREW-SHCS-STL-BO EA 4
26 15759 WASHER-1/4 HARD BLK OX 1/8 THK EA 4
27 16772 PLATE- MOTOR- Z AXIS EA 1
28 20328 MOTOR ASSY- HEAVY DUTY TRAK DPM EA 1
30 M10-1.5X20 25B SCREW-SHCS-STL-BO EA 4
31 M10 73B WASHER-SPLIT LOCK-STL-BO EA 8
32 17030 LOUVER- SPACER EA 1
34 M10-1.5X45 25B SCREW-SHCS-STL-BO EA 4

143
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-27 Z-Axis Drive Assembly – DPMS3/DPMS5

144
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Z-Axis Drive Assembly Parts List – DPMS3/DPMS5

Item P/N Description

1 16806-M BALL SCREW ASSY- Z-AXIS
2 PJ540015 BRACKET LOWER ELEVATING BALL SCREW
3 22583 BEARING SELF ALIGNMENT SKF 2205E-2RS1TN9
4 16774 COVER - BEARING
5 16795 MODIFIED BEVEL GEAR BS1236-2A
6 M10-1.5X10 40B SCREW-SOC SET-STL-BO-CUP
7 16770 MODIFICATION OF 3 HP RAM PING JENG PART
8 M6 73B WASHER-SPLIT LOCK-STL-BO
9 M6-1.0X25 25B SCREW-SHCS-STL-BO
10 7205-AVH NILOS RING-7205
11 16295-1 HOUSING- BEARING Z-AXIS
12 16302 RING-BEARING HOUSING
13 23940 BEARING SET-ANGULAR CONTACT-7205 BECBP
14 16773 NUT CLAMP-Z AXIS
15 10-32X3/4 25B SCREW-SHCS-STL-BO
16 16350 FERRULE-SPROCKET
17 16983 PULLEY-SOLID 44 TEETH Z-AXIS
18 N01 LOCKNUT
19 W01 LOCKWASHER
20 M8 73B WASHER-SPLIT LOCK-STL-BO
21 98481A090 KEY WOODRUFF #404-1/8 X 1/2
22 M8-1.25X20 25B SCREW-SHCS-STL-BO
23 710-5M-15 BELT - TIMING
24 21944 PLATE BALL SCREW SUPPORT - Z AXIS
25 1/4-20X1 1/4 25B SCREW-SHCS-STL-BO
26 15759 WASHER-1/4 HARD BLK OX 1/8 THK
27 23197 BRACKET-Z AXIS MOTOR-DPMS
28 23198 MOTOR DRIVER ASSY-PT4-DPM-SM-4050
31 M10 73B WASHER-SPLIT LOCK-STL-BO
32 17030 LOUVER- SPACER
34 M10-1.5X45 25B SCREW-SHCS-STL-BO
35 M10 71B WASHER-FLAT SAE-STL-BO
30 98481A090 KEY WOODRUFF #404-1/8 X 1/2
i00771-Z-S

145
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-28 DPME2
Z-Axis Drive Train

146
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Z-Axis Drive Train Parts List – DPME2

Item P/N Description Qty

1 23662 BALL SCREW ASSY- Z-AXIS - LM0010 1
2 23658 BRACKET LOWER ELEVATING BALL SCREW - SW0008 1
3 2205E-2RS1TN9 BEARING SELF ALIGNMENT SKF 1
4 16774 COVER - BEARING-SW00007 1
5
6
7 16770 MODIFICATION OF 3 HP RAM PING JENG PART 1
8 M6 73B WASHER-SPLIT LOCK-STL-BO 6
9 M6-1.0X25 25B SCREW-SHCS-STL-BO 6
10 7205-AVH NILOS RING-7205 1
11 16295-1 HOUSING- BEARING Z-AXIS 1
12 16302 RING-BEARING HOUSING 1
13 20374 BEARING-ANGULAR CONTACT-7205 BECBP 2
14 16773 NUT CLAMP-Z AXIS 1
15 10-32X3/4 25B SCREW-SHCS-STL-BO 1
16 16350 FERRULE-SPROCKET 1
17 16983 PULLEY-SOLID 44 TEETH Z-AXIS 1
18 N01 LOCKNUT 1
19 W01 LOCKWASHER 1
20 M8 73B WASHER-SPLIT LOCK-STL-BO 4
21 98481A090 KEY WOODRUFF #404-1/8 X 1/2 1
22 M8-1.25X20 25B SCREW-SHCS-STL-BO 4
23 710-5M-15 BELT - TIMING 1
24 23664 PLATE BALL SCREW SUPPORT - Z AXIS - LM0011 1
25 1/4-20X1 1/4 25B SCREW-SHCS-STL-BO 4
26 15759 WASHER-1/4 HARD BLK OX 1/8 THK 4
27 23655 BRACKET-Z AXIS MOTOR-DPME2 1
28 23198 MOTOR DRIVER ASSY-PT4-DPM-SM-4050 1
31 M10 73B WASHER-SPLIT LOCK-STL-BO 8
32 17030 LOUVER- SPACER 1
34 M10-1.5X45 25B SCREW-SHCS-STL-BO 8
35 M10 71B WASHER-FLAT SAE-STL-BO 4
i16790--XXX

147
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.1.12 Air Solenoid Replacement for Power Drawbar –
DPMS3/DPMS5 only
1. Unhook the air from the machine.
2. Unplug the power cable that connects to the right side of the air regulator
bracket.
3. Remove the 2 screws that hold the connector to the bracket.
4. Undo the airline that runs from the oiler to the power drawbar if that option is
installed on the machine.
5. Remove the 2 screws on the left side of the bracket that holds the air manifold
to the U-shaped bracket.
6. With the assembly in hand, unthread the solenoid from the rear of the air
7. regulator. The solenoid and cable will be replaced as a unit.

Power Drawbar Parts List

Item P/N Title

1 22581-1 AIR GUN ASSY ONLY- TORQUE RITE
2 22603-NST DRAWBAR-DPMS3
3 20893 TOP WASHER
4 22380-2 AIR REGULATOR ASSY
5 22603-CAT DRAWBAR-DPMS3
6 22581-2 SWITCH - CONTROL HEAD - TORQUE RITE
7 22581-4 NOSEPIECE FOR SPINDLE
8 1/4" NPT AIR FITTING 90°
9 3/8 O.D. TUBING 132" LG.
10 3/8 O.D. TUBING 27" LG.
11 22641-NMTB DRAWBAR-DPMS5
12 22641-CAT DRAWBAR-DPMS5
i00875

148
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-29
Power Drawbar

5.1.13 Spindle Motor Wiring

All bed mill spindle motors are wired for 220 or 440 volts except the DPME2, which is
wired for 220 volts only. See Figure 5-29 for how to wire all motors with exception to
model DPME2. See Figure 5-30 for how to wire the spindle control motor for DPME2

149
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-30
Spindle Motor Wiring (except DPME2)

150
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-31
Spindle Motor Wiring – Spindle Control – DPME2 only

151
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.1.14 Electric Box Service – TRM (P/N 20655-220 or 20655-
440), DPM & DPM5 only (P/N 17009-220 or 17009-440)
The electric box contains a relay module, which comprises all electrics for the machine
and control (relays, contacts, fuses, etc.). Figure 2-15 in Section 2 shows the electrical
diagram for the relay module. Refer to Section 5.1.15 for Auxiliary Function Interface
(DPM/DPM5 only).

The entire relay module may easily be exchanged or replaced with the following
procedure.

DANGER!
Always disconnect the 220V/440V, 3-phase input and the 15-VAC input before opening the
electrics box.

1. Unplug all plugs connected to the relay module located on the side of the electrics
box.

2. Unscrew the two Philips head screws on the clamps that hold the electrics box door
shut. Open the electrics box door. The door interlock must be in the Off position to
open.

3. Disconnect the 3-phase into the relay module and the 3-phase out to the spindle
motor (see Figure 2-15).

4. Unscrew the 21 black Philip head screws on the side of the electrics box, and the
2 black Philips head screws inside the electrics box that connect the relay module
to the electrics box. The entire relay module can now slide out of the electrics
box.

5.1.14.1 Fuses
The fuse identification is shown on the relay module label. Use only the correct fuses.

5.1.14.2 Red LED Diagnostic Status Indicators

There are 12 red LED diagnostic status indicators located on the right side of the relay
module.

The meaning of these LED's is as follows (LED 1 is on the top):

1. LED 1 is on when the pendant is switched on. LED 1 also indicates that the
computer module is receiving 115 VAC.

2. LED 2 is on when the E-Stop on the switch box is in the Out position and the
overload relay has not been tripped. LED 2 is on during normal operation.

3. LED 3 is on when the switch box is receiving 115 VAC. LED 3 is on during
normal operation.

4. LED 4 is on when the spindle switch on the switch box is in the 1 or 2 position
and the spindle is on.

152
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5. LED 5 is on when the coolant pump is on. The coolant pump can be turned on
either by the switch box or via a CNC auxiliary function (see Section 5.1.15).
(DPM only)

6. LED 6 is on when the overload relay is tripped. LED 6 is off during normal
operation.

7. LED 7 is on when the E-Stop on the switch box is in the Out position.
LED 7 is on during normal operation.

8. LED 8 flashes on when the Haas rotary table is being indexed one cycle or step.
The function is controlled through Auxiliary Function 3 (see Section 5.1.15).
(DPM only)

9. LED 9 flashes on when the Haas rotary table has completed indexing one cycle
or step. (DPM only)

10. LED 10 is on when Auxiliary Function 1 (coolant pump) is on (see

Section 5.1.15). (DPM only)

11. LED 11 is on when Auxiliary Function 2 (air relay) is on (see Section 5.1.15).
(DPM only)

12. LED 12 is on when Auxiliary function (spindle motor) is on (see Section 5.1.15).
(DPM only)

5.1.15 Auxiliary Function Interface (DPM/DPM-5 only)

Refer to the machine programming, operating, and care manual for the procedures to
use the auxiliary functions.

AUX FUNCTION 1 – A/C Relay. Auxiliary Function 1 turns power to 115V A/C (2
amp) socket on and off. The socket is located on the side of the Electrics Box. Power to
this socket can also be controlled by the Coolant Switch on the front panel of the Switch
Box. The 115V is turned on when either the programming AUX 1 is activated, or when
the Switch Box switch is turned to the On position. The most common use for this
function is the coolant pump, but other A/C driver devices may be substituted (for
example, a light).

AUX FUNCTION 2 – Air Relay. Auxiliary Function 2 turns shop air on and off. Shop air
"in" is connected through the bracket on the back of the column. The fitting is ready to
accept a standard quick disconnect device with a 1/4 inch pipe thread. Air pressure is
not to exceed 100 psi.

Shop air "out" is at the "Pneumatic Device Out" port. Connect the plastic tubing supplied
in the hardware kit. The most common use for this function is for a spray mister. Lube
and water separators are recommended. (Minimum 24" from DPM.)

AUX FUNCTION 3 – Rotary Indexer. Auxiliary Function 3 transmits an electronic

signal to be used by a relay or another electronically driven device. It also transmits
input back from the device to restart the program. The most common use is a Haas type
rotary indexer.

153
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 The signal output is a 0.3 second activation of a solid-state relay between Pins 3 and 4.
The maximum permissible voltage is 60 VDC or 40 VAC with a maximum current of .025 amps.

The input is a 0.1 second or greater activation of the external device (indexer) relay
between Pins 1 and 2. The relay impedance must be less than 500 ohms.

The connector for this output is located on the side of the Electrics Box and is labeled
"Logic To Indexer." On this connector Pin 1 is on the bottom, Pin 2 is on the left, Pin 3 is
on the right, and Pin 4 is on the top.

Included in the hardware kit is a cable with a connector for the Electrics Box and a Haas Indexer.

AUX FUNCTION 4 – Spindle Motor. Auxiliary Function 4 turns the spindle motor off at
a tool change and at the end of the part program. This capability is designed into the
DPM & DPM5.

5.1.16 Feed Trip Adjustment – All bed mills except DPME2

If the feed trip is adjusted too light it will inadvertently trip when drilling. If too heavy, it
will not trip accurately and stress the mechanism. The correct adjustment depends on
the operation to be performed. To adjust:
1. Release the lock nut.
2. Engage the trip handle--move it left.
3. Adjust the micrometer nut against the quill stop knob.
4. Slowly turn the adjusting screw until the handle trips.
5. Tighten the lock nut.
6. Check the reaction. If too sensitive, lower the adjusting screw slightly. If too
heavy, raise it.

Figure 5-32
Feed Trip Adjustment

I00153

5.1.17 Quill Clock Spring Replacement and Adjustment

The quill Clock Spring counterbalances the weight of the quill and tool.

154
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-33
Quill Clock Spring
Replacement

1. Move the quill to its top position and lock it in place.

2. Remove the quill handle, hub (by removing Screw A) and key.

3. Remove Screws B and allow the spring housing to unwind.

4. Remove the spring. It is held by a pin on the shaft and slot in the housing.

5. Replace the spring. Rotate the housing clockwise until the spring catches the shaft pin.

6. Rotate (wind up) the housing 1 1/2 turns, replace Screws B, key hub, Screw A, and handle.

5.1.18 Spindle Motor Removal and Replacement

5.1.18.1 TRM, DPM, DPM5, Sport B3, Sport B5, DPMS3 & DPMS5

CAUTION!
The motor is heavy--about 60 pounds. Be certain you have the proper equipment or assistance.

1. While the spindle is running, change the RPM to its lowest value.

2. Disconnect the power to the motor. It is recommended that the power

disconnect be made from the shop feeder box.

3. Disconnect the electrical connection in the conduit box attached to the motor.

4. Crank the speed changer to the highest RPM value.

5. Remove the two screws that fasten the motor to the top of the housing.

155
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 6. Tilt the motor forward and remove the belt from the motor pulley. Remove the
motor.

7. If the motor is to be replaced, remove the M8 socket head cap screw at the
end of the motor shaft. Slide the pulley assembly off the motor shaft and onto
the new motor.

Figure 5-34
Spindle Motor

I00155

5.1.18.2 Spindle Motor Removal & Replacement – Spindle Control

DPME2 only (refer to Figure 5-34, Item 1 & Figure 6-21, Item
26)

1. Disconnect the power to the motor. It is recommended that the power

disconnect be made from the shop feeder box.
2. Disconnect the electrical connection in the conduit box attached to the motor.
3. Remove the three bolts that hold the motor pulley cover in place to gain access
to the belt.
4. Remove the four bolts that mount the motor to the top head housing.

CAUTION!
The motor is heavy--about 60 pounds. Be certain you have the proper equipment or assistance.
6. Loosen the ½” nut on the belt tensioner puller screw at the back of the motor.
Release the belt tension using a #6 hex key to unscrew the tensioner puller
screw from the motor housing.
7. Tilt the motor towards the back and remove the belt from the motor pulley.
Remove the motor.
8. If the motor is to be replaced, remove pulley assembly off the motor shaft and
onto the new motor.

156
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-34 DPME2

157
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 DPME2 - Spindle Head Parts List

Item P/N Description Qty

1 23585 MOTOR-3 HP/3 PH-1725 RPM-220 VOLTS 1
2 23629 CONTROL BOX-HEAD-DPME 1
3 23698 WIRING ASSY-SPINDLE HEAD-DPME-CONTROL BOX TO SWITCHES 1
3A 23621 NAMEPLATE-DPME-SPINDLE HEAD 1
3B 23624 POTENTIOMETER 1
3C 23623 TACHOMETER-RPM 0-5000 HIGH/0-600 LOW 1
3D 23628 FWD/REV SWITCH 1
3E 22125-03 SLEEVE- SHRINKABLE TUBING 3 IN
3F 21953-18 TERMINAL- RING TONGUE 2
3G 22404-18 TERMINAL- WIRE PIDG FORK 8
3H 22285-YL-20G WIRE- UL1007 118 IN
3J 22475 TIE WRAP-4 IN-PLASTIC 1
7 23632 SPINDLE PULLEY-117 mm 1
8 23597 BELT-MICRO-V-J PROFILE 10 RIBS "J" 1
9 23631 MOTOR PULLEY-117 mm-DPME 1
10 23695 HARNESS ASSY-SPINDLE CONTROL-DPME-ELECTRIC BOX TO SWITCHES 1
11 23573 SPACER-SPINDLE SHAFT BUSHING-DPME 1
12 23574 PLATE RETAINER-SPINDLE SHAFT-DPME 1
13 23755 KEY-8 mm x 8 mm 1
14 23756 KEY-10 mm x 10 mm 1
15 M8 70B WASHER-FLAT USS-STL-BO 4
16 M8 73B WASHER-SPLIT LOCK-STL-BO 4
17 M8-1.25X40 24B SCREW-HEX HEAD-STL-BO 4
18 VS109 FRU-K3-DRAWBAR 7/16-20UNF 1
19 VS109-1 SPACER-DRAWBAR 1
20 20849 QUILL HANDLE 1
21 23696 HARNESS ASSY-SPINDLE MOTOR-DPME2 1
i23610-XXX

158
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.1.19 Drive Belt Replacement
5.1.19.1 TRM, DPM, DPM5, Sport B3, Sport B5, DPMS3 & DPMS5

1. Remove the motor.

2. Remove the draw bar and its bushing.

3. Remove the three Screws A and use M6 x 35mm screws in the adjacent tapped
holes to remove the Bearing Cap.

4. Remove the nut from the fine speed adjustment Screw B and turn the screw all
the way down through the casting. Catch it from the motor hole.

5. Remove six Screws C holding the belt housing to the subplate.

6. Remove the four screws holding the speed changer.

7. Remove the belt housing.

8. Replace the belt by sliding it over the speed changer.

9. In reassembly be certain the fine speed adjustment Screw B goes into the slot of
the Speed Change Plate D in the area in which the screw is not threaded.

i00156
Figure 5-35
Drive Belt Replacement

159
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.1.19.2 Drive Belt Replacement for Spindle Control - DPME2

1. Remove the draw bar and its bushing (remove power drawbar if present).
2. Remove the three Screws A and use M6 x 35mm screws in the adjacent tapped
holes to remove the Bearing Cap.
3. Follow instructions for spindle motor removal and remove motor so top head
housing can
be removed with ease.
4. Remove the six screws “C” that hold the belt housing to the subplate.
5. Disconnect the spindle control harness at the head control box.
6. Lift off the belt housing; then remove belt.

5.1.20 Timing Belt Replacement

1. Remove the motor and drive belt.

2. Slide the top or adjustable varidisc pulley assembly off the shaft.

3. Remove the three M8 screws holding the belt housing base to the gear housing.

4. Lower the quill about 4 inches.

5. Remove the belt housing base and lower or stationary varidisc pulley assembly.

6. Replace the timing belt.

5.1.21 Brake Shoe Replacement

1. Remove the motor, drive belt and complete Steps 1-5 of the timing belt replacement
procedure.

2. Remove the two M6 cap screws from the bottom of the belt housing base.

3. Separate the belt housing base from the lower or stationary varidisc pulley. This
is a slight press fit.

4. Remove the 2 springs.

5. Replace the brake shoes.

5.1.22 Spindle Replacement

1. Remove the draw bar and its bushing.

2. Lower the quill about 1 inch and lock.

160
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 3. Remove the setscrew from the back of the spindle.

4. Loosen (unscrew) the large black ring (nosepiece) with a spanner wrench.
Note: The nosepiece has a left hand thread-- rotate counterclockwise to loosen.

5. Using a soft bar about 12 inches long, alternately tap on the top of the spindle
and loosen a few threads on the nosepiece until fully unscrewed (the nosepiece
will remain attached to the spindle).

6. Continue to tap the spindle out of the quill. The spindle bearings will come out with the
spindle.

Figure 5-36

5.2 Maintenance
5.2.1 Gib Adjustments
The objective of adjusting the gibs is to eliminate as much play in the table, saddle and
ram sliding surfaces as possible without having the tightness of the gib interfere with
their free movement and cause a decrease in the accuracy and/or performance of the
machine due to excessive friction.
5.2.1.1 Table Gib Adjustment, X-Axis
5.2.1.1.1 TRM, DPM, Sport B3, DPMS3, DPME2

1. Clean all chips, dirt and excess oil from the table and saddle.
2. Center the saddle on the bed ways.
3. Move the table fully to the left side of the saddle.
Note: For machines that have excessive wear in the center of the table way, it will
be necessary to center the table on the saddle. The resulting adjustment of the

161
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 gib will be compromised to account for the varying clearance from the center to
the ends of the table.
4. Attach a .0001 dial indicator with a magnetic base to the left front of the
saddle. Place the indicator stylus on the front surface of the table as close to
the indicator base as possible.

Figure 5-37 – Table Gib Adjustment

5. Move the left end of the table back and forth and note the amount of
movement on the dial indicator. Adjust the X-axis gib until the registered
movement is .0010-.0015.

• To adjust the gib for excessive clearance: Loosen the gib lock screw on the
right end of the saddle. Estimate the amount of gib lock screw adjustment
required, and tighten the gib lock screw on the left end of the saddle.
Tighten the gib lock screw on the right end of the saddle to lock the give in
place, and recheck. Repeat as necessary.

• To adjust the gib for too small of a clearance: Loosen the gib lock screw on
the left end of the saddle. Estimate the amount of gib lock screw
adjustment required, and tighten the gib lock screw on the right end of the
saddle. Tighten the gib lock screw on the left end of the saddle to lock the
gib in place, and recheck. Repeat as necessary.

6. Center the table on the saddle and run Service Code 12 to set the Feed Forward
Constant

162
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-38
Table Gib Screw
5.2.1.1.2 DPM5, Sport B5, DPMS5
The X-axis has 2 gibs for the table because of the length of the saddle. Each gib is
adjusted from each end of the table. There are not 2 adjustment screws at either end of
the gib like the Y-axis and Z-axis.

Clean all chips, dirt and excess oil from the table.
Remove the table trays.
1. Move the table to the left and mount the indicator at Point D and move the table
back and forth. Note the amount of movement of the dial indicator. Adjust gib
until the movement is between .0005-.001.
2. Move the table to the right and mount the indicator at Point A and move the
table back and forth. Note the amount of movement of the dial indicator. Adjust
gib until the movement is between .0005-.001.
• To adjust the gib for excess clearance: Loosen the nut closest to the table
and tighten the nut furthest from the table. Once the clearance has been
taken up tighten each nut against the gib bracket. Do this for each end of
the table.
• To adjust the gib for too small of a clearance: Loosen the nut furthest from
the table and tighten the inside nut up against the bracket to pull the gib
away from the machine. Once the clearance has been taken up tighten each
nut against the gib bracket. Do this for each end of the table.
3. Center the table on the saddle and run Service Code 12 to set the Feed Forward
Constant

4. Replace the table trays. See Figure 5-39.

163
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-39
DPMS5 Table Gib & Saddle Bottom Gib Adjustment

164
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.2.1.2 Saddle Side Gib Adjustment, Y-Axis – All machines
See Figure 5-40

1. Clean all chips, dirt and excess oil from the table and saddle.
2. Center the saddle on the bed ways.
3. Move the table fully to the left side of the saddle.
4. Remove the chip wiper guard and chip wiper from the front and rear of the left
side box way.

Figure 5-40
Saddle Side Gib Adjustment

5. Attach a .0001 dial indicator with a magnetic base to the left front of the saddle.
Place the indicator stylus on the edge of the large box way.
6. Move the left end of the table back and forth and note the amount of movement
on the dial indicator. Adjust the Y-axis side gib until the registered movement is
.0010-.0015.
• To adjust the gib for excessive clearance:
Loosen the gib lock screw on the back of the saddle. Estimate the amount
of gib lock screw adjustment required, and tighten the gib lock screw on the
front of the saddle. Tighten the gib lock screw on the back end of the saddle
to lock the gib in place, and recheck. Repeat as necessary
• To adjust the gib for too small of a clearance:
Loosen the gib lock screw on the front of the saddle. Estimate the amount
of gib lock screw adjustment required, and tighten the gib lock screw on the
back of the saddle. Tighten the gib lock screw on the front of the saddle to
lock the gib in place, and recheck. Repeat as necessary.

165
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 7. Replace the front and rear chip wiper, and chip wiper guard.
8. Center the table on the saddle and run Service Code 12 to set the Feed Forward
Constant.
5.2.1.3 Saddle Bottom Gib Adjustment, Y-Axis
5.2.1.3.1 TRM, DPM, Sport B3, DPMS3

See Figure 5-41.

1. Clean all chips, dirt and excess oil from the table and saddle.
2. Center the saddle on the bed ways.
3. Move the table fully to the left side of the saddle.
4. Attach a .0001 dial indicator with a magnetic base to the left front of the saddle.
Place the indicator stylus on the top surface of the box way.
5. Lift the end of the table up and note the amount of movement on the dial
indicator. Adjust the Y-axis left bottom gib until the registered movement is
.0010-.0015.
6. Move the table fully to the right.
7. Reposition the indicator to the right front of the saddle.
8. Lift the right end of the table up and note the amount of movement on the dial
indicator. Adjust the Y-axis right bottom gib until the registered movement is .0010-
.0015.

• To adjust the gib for excessive clearance:

Loosen the gib lock screw on the back of the saddle. Estimate the amount
of gib lock screw adjustment required, and tighten the gib lock screw on the
front of the saddle. Tighten the gib lock screw on the back end of the saddle
to lock the gib in place, and recheck. Repeat as necessary.

• To adjust the gib for too small of a clearance:

Loosen the gib lock screw on the front of the saddle. Estimate the amount
of gib lock screw adjustment required and tighten the gib lock screw on the
back of the saddle. Tighten the gib lock screw on the front of the saddle to
lock the gib in place, and recheck. Repeat as necessary.

166
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-41 Saddle Bottom Gib Adjustment –
TRM, DPM, Sport B3, DPMS3

167
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.2.1.3.2 DPM5, Sport B5, DPMS5
It is unrealistic to adjust the Y bottom ways the same way as we do on the lighter mills
because of the extra weight of the saddle and table.

1. Clean all chips, dirt and excess oil from the table and saddle.
2. Center the saddle on the bed ways.
3. Mount your indicator on the left side of the saddle (Point C) with the table in the
center of its travel and zero out your indicator.
4. Move the table all the way to the right side. When the gibs are adjusted
properly you should see no more than 0.0003” movement on the indicator.
5. Do the same thing on the right side of the saddle (Point B) this time moving the
table all the way to the left. The reading should be positive on the indicator
because the saddle should rise where you are indicating.

Note: You can get better readings than 0.0003” but the torque on the Y ball screw
may exceed our recommended levels. Remove the ball screw cover and check the
torque with an in-lb torque wrench. Normally, the torque should be around 15 in-
lbs. Do not exceed 20 in-lbs. Values higher than this may cause circularity
problems.

See Figure 5-41 for an illustration.

• To adjust the gib for excessive clearance:

Loosen the gib lock screw on the back of the saddle. Estimate the amount of gib
lock screw adjustment required, and tighten the gib lock screw on the front of
the saddle. Tighten the gib lock screw on the back end of the saddle to lock the
gib in place, and recheck. Repeat as necessary.

• To adjust the gib for too small of a clearance:

Loosen the gib lock screw on the front of the saddle. Estimate the amount of gib
lock screw adjustment required and tighten the gib lock screw on the back of the
saddle. Tighten the gib lock screw on the front of the saddle to lock the gib in
place, and recheck. Repeat as necessary.

5.2.1.4 Ram Back Gib Adjustment - Z Axis – All Machines

1. Clean all chips, dirt and excess oil from the table and saddle.

2. Disconnect one end of the upper and lower way cover where it is attached to the ram.

3 Position the milling head such that the table can be reached by extending the
quill
approximately 3/4 of its travel.

4. Place a wood block on the table underneath the spindle.

5. Attach a .0001 dial indicator with a magnetic base to the column near the base
of the ram on the left side of the machine. Place the indicator stylus on the
rear surface of the ram near the bottom.

168
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 5-42
Ram Back Gib
6. Extend the quill until it touches the wood block. Using the quill handle, push the
spindle nose against the wood block and note the amount of movement on the
dial indicator. Adjust the left side gib until the registered movement is .001-
.0015.

To adjust the gib for excessive clearance: Loosen the gib lock screw on the
bottom of the ram. Estimate the amount of gib lock screw adjustment required and
tighten the gib lock screw on the top of the ram. Tighten the gib lock screw on the
bottom of the ram to lock the gib in place, and recheck. Repeat as necessary.

To adjust the gib for too small of a clearance: Loosen the gib lock screw on
the top of the ram. Estimate the amount of gib lock screw adjustment required and
tighten the gib lock screw on the bottom of the ram. Tighten the gib lock screw on
the bottom of the ram. Tighten the gib lock screw on the top of the ram to lock the
gib in place, and recheck. Repeat as necessary.

7. Run Service Code 12 to set the feed forward constant.

8. Repeat the procedure for the back gib on the right side of the machine.

5.2.1.5 Ram Side Gib Adjustment - Z Axis –

TRM, DPM, DPM5, Sport B3, Sport B5, DPMS3, & DPMS5
1. Clean all chips, dirt and excess oil from the column ways.

2. Attach a .0001 dial indicator with a magnetic base towards the rear of the table
on the right side of the ram. Place the indicator stylus on the ram in line and
below the lower mounting bolt for the coolant hose connector block. (See Figure
5-43).

169
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 3. Lock and unlock the lower ram side gib lock and note the amount of movement
on the dial indicator. Adjust the ram side gib until the registered movement is
.0005- .0010.

To adjust the gib for excessive clearance: Loosen the gib lock screw on the
bottom of the ram. Estimate the amount of gib lock screw adjustment required, and
tighten the gib lock screw on the top of the ram. Tighten the gib lock screw on the
bottom of the ram to lock the gib in place, and recheck. Repeat as necessary.

To adjust the gib for too small of a clearance: Loosen the gib lock screw on
the top of the ram. Estimate the amount of gib lock screw adjustment required and
tighten the gib lock screw on the bottom of the ram. Tighten the gib lock screw on
the top of the ram to lock the gib in place, and recheck. Repeat as necessary.

4. Run Service Code 12 to set the feed forward constant.

5. Reattach the upper and lower way cover to the ram.

CAUTION!
Be careful not to over tighten the ram gibs. Over tightening may lead to faulting and
repeatability problems. Double-check the gib adjustment by checking the torque on the Z-axis.
Use an in-lb torque wrench on top of the ball screw and typical readings should be from 12 to 17
in-lbs and consistent across the Z travel.

Figure 5-43 Ram Side Gib Adjustment

5.2.2 Calibration & Backlash Constants -
Sport B3, Sport B5, DPMS3, DPMS5, & DPME2
Calibration and backlash constants were set as part of the installation and set-up of your
system. They should be re-set when indicated in the Troubleshooting section or after
the replacement of the Computer module, or any parts of the drive train.

170
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 5.2.2.1 X, Y, Z (Ram) and Quill Calibration –
DPMS3, DPMS5, & DPME2

Calibration is used to teach the machine a known distance. We typically calibrate our
machines over a 150 mm distance. There is no limit to how far you can calibrate the
machine. Refer to Figure 5-44.

1. If you have installed TRAK Sensors, move each axis through its travel 4-6 times
in order to allow the gage wheel to establish its track.
2. Set-up a gauge block or standard and indicate it parallel to the axis you are
calibrating.
Note: Put the display in Inch or mm to match your gage block. Recommended gage
blocks are:
• X and Y -- 150mm or 6”
• Z -- 75 mm or 3”
3. Set a 0.0001” indicator in the spindle and move it up to one side of the gage
block or standard.
4. Go to setup mode, go to section “B” and press CODE 123.
5. Select the axis you want to calibrate X, Y or Z. For the quill press the F1 key
labeled QUILL.
6. Follow the instructions on the screen to complete calibration.

5.2.2.2 Z Ram Ball Screw Calibration – DPM only

Whenever the Z Ram ball screw or system TRAK A.G.E. computer module is replaced, the
Z Ram motion must be recalibrated.

1. Create a set up similar to that shown in Figure 5-44, except orient the gage block
and reference to measure vertical ram motion.

2. Lock the quill.

3. Press MODE, SET-UP, SERV CODES, 124, INC SET.

4. Follow the instructions on the screen.

5. If the difference between the measured length and standard length is more than
0.75 percent (no ballscrew has this much error), check your standard and repeat
the procedure.

171
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-44 Calibration Set-Up

5.2.2.3 Backlash Compensation –MX2, MX3, AGE2, AGE3,

Optional for M3, SM3

Code 11: Set X or Y backlash constant

Note: this procedure is on systems with dual feedback only.

Go to setup mode, SERV codes, and enter CODE 11. Refer to service codes in Section
4.11 for further explanation.

Code 127: Set X or Y Backlash Constant

Note: this procedure is only for systems without single feedback M/SM, EDGE.

Every mechanical system has at least a little backlash or lost motion. It is produced by
the small amount of play between the gibs and ways, and mostly by the accumulative
bending or elasticity of all the parts of the drive train under load. The backlash constant
is factory set, but may need to be adjusted periodically.

1. Set a .0001-inch dial indicator in the spindle, and touch off on a block or the
vise along the direction (X, Y or Z) you wish to check, or set the backlash
constant.
2. Turn on the ProtoTRAK and at the Main Menu, follow the procedure below
precisely:

172
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Conversation Says You Do
a. --- a. Press MODE
b. Select Mode b. Press SET UP
c. Select c. Press SERV CODES
d. Select d. Press “B”
e. Select Code 127 e. Press X or Y or Z
f. Backlash Value = _ _ _ _ f. What is shown is the current value.
Follow the instruction on the screen
and press the appropriate soft keys.
Wait a few seconds between each
INCR VALUE or DECR VALUE press.
g. The following is an example of what you For example, if the up and down "Oscillation
might see when running this code. Value" shown in the conversation line is .00278
inch, and the dial indicator is moving back and
forth .0012, the true backlash value is .00278 -
.0012 = .00158 inch. Input this by pressing
MODE, SET UP, SERV CODE, 128, SET and
then .00158, SET, RETURN.

3. The X backlash identified and stored in Step 2 should be less than 0.003” on a
new machine. If it is appreciably larger, inspect the drive train for loose bolts,
brackets, bearings, etc.

The backlash can also be found manually with a 0.0001” indicator with the
following method.
• Load the indicator to zero from one direction and zero out the DRO.
• Move the indicator to 0.002” and then back to zero. Do not over shoot
0, otherwise start over.
• Whatever number appears on the screen is the backlash value.
• Enter this value into service code 128.
• After entering this number redo the process. The DRO and indicator
should now both read 0.

CODE 128: Input Backlash Constant

Code 128 allows you to enter the backlash values for each axis. It displays the value
after it enters. This code is only used on machines with motor encoders only.

5.2.3 Head Rotation and Tramming

The TRAK Bed Mills head is free to rotate up to 90 degrees to the right or
left.
5.2.3.1 To Rotate the Head:

1. Loosen the four locknuts.

2. Rotate the head with the adjusting worm shaft.

173
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Note: Make sure to support head when exceeding 45° angle.

3. Tighten the locknuts. Snug each locknut, then lightly tighten each locknut, then
fully tighten each locknut in a crisscross pattern.
4. Use the method shown in Figure 5-45 and a parallel bar to square the head to the
table.

5.2.3.2 Tramming the Head

The purpose of tramming the head is make sure the head is perpendicular to the top of
the table from both side to side and back to front.

Side to side tolerance – 0.001”

Side-to-Side Alignment
1. Make sure the machine is level.
2. Make sure the table has been clean and the Z gibs are adjusted properly.
Mount a dial indicator in a tool holder and mount in the quill.
3. Adjust the Y-axis so that the spindle is in the center of the table.
4. Adjust the Z ram so that the dial indicator will reach the table.
5. Move the dial indicator to 6 o’clock position and adjust the face so the needle is
zero.
6. Do a series of sweeps from 3 o’clock to 9 o’clock and check for the repeatability
of the setup. The head should be trammed with an 0.001”
7. If the head is out of tram from side to side, loosen the 4 head bolts and rotate
the head with the worm shaft.
8. Once the head has been trammed tighten the 4 heads bolts. Be careful not to
move the head while tightening. Tighten the bolts in a criss-cross pattern.

Figure 5-45
Tramming of Head

174
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Back to Front Adjustment
Note: The head of the bed mill machine is adjusted at the factory. This procedure
should only be needed for a head replacement.

Using the dial indicator, sweep the table from 6 o’clock to 12 o’clock. The head should
be trammed within 0.0000 to 0.0005” from front to back. (Note: the head must droop
down rather than up because tool pressure will take care of the extra 0.0005”.)

Note: Minor adjustments can be made with the back ram gibs. Tightening the gibs will
tend to tilt the head up from the table. Loosening the gibs tends to allow the head to
droop down toward the table. Over tightening or loosening can lead to other problems
with the machine. Typical adjustments with the gibs is 0.0005” or less.

5.2.4 Limit Switch Option – DPMS3, DPMS5, & DPME2

5.2.4.1 X-Axis Limit Switch-Stop Installation and Adjustment
The limit switch-stops for the X-axis are mounted to the front side of the table. The limit
switch-stop consists of a square bracket, which is fastened to the T-slot on the front side
of the table. Each limit switch-stop must be set to a specific distance from the end of the
table in order to maximize travel and simultaneously prevent serious damage to the
machine in the event of a crash. All limit switches are set at the factory for maximum
travel.

Procedure for Setting X Limit Switch

1. Loosen the X-axis square bracket on each side of the table.
2. Slide each X-axis square bracket within the T-slot to the end of the table.
3. Slowly move the table to one side by hand until the end of the travel is reached.
4. In DRO mode set X = 0 ABS.

CAUTION!
The limit switch must be triggered a minimum of ½” before the machine reaches its
travel limits in both directions. This allows sufficient room for the servomotors to stop
when the limit switch is hit at 150 ipm.
5. Using the DRO display, back the table off 1/2".
6. Lock the limit switch bracket in place.
7. Jog the table at 150ipm to each side and verify that the limit switch is working
properly. Also, make sure that the table does not exceed its travel and crash.

5.2.4.2 Y & Z-Axis Limit Switch-Stops

The limit switch-stops for the Y-axis are mounted on the side of the bed. The limit switch
is triggered by hitting the cam stop on the saddle. The cam is placed to ensure
maximum travel.

The limit switch-stops for the Z-axis are mounted on the side of the column. The limit
switch is triggered by hitting the trip lever. After contact is made with the limit switch,

175
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 lift the trip lever and jog the head up or down to move the machine away from the limit.
The trip levers are placed to ensure maximum travel.

5.2.5 Accuracy and Repeatability Measurements

Positional accuracy and repeatability programs are included in the program list of the control.
Use these programs to check positional accuracy, uni-directional repeatability, and bi-directional
repeatability. These programs are used to check each machine during the assembly process
and can be utilized for checking the machine in the field when necessary.
1. Set-up a gage block or standard and indicate it parallel to the axis you are checking.
Recommended gage blocks are 150 mm or 6.0 inches for X and Y, 75 mm or 3.0
inches for Z.
2. Set a 0.0001" indicator on the spindle and move it up to one side of the gage
block or standard. If using a 150 mm standard position the flats toward the
motor side of the table for the X-axis, position the flats toward the Z column for
the Y-axis
3. Select the axis you want to check by selecting the appropriate program file as
stated in the above paragraph.
4. When running the program, rotate the standard out-of-the-way of the oncoming
indicator. The program will allow sufficient time to turn the standard for a clear
path after which time it can be turned again for another reading.

176
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
FIGURE 5-46
Typical set-up for an X-axis accuracy/repeatability check
5.2.5.1 The Program for the X-axis Will Run as Follows:
Movement from START to point A (about 2.0" of travel)
From the START position, manually advance the table to position A. Then zero out
the indicator and the DRO at point A. Set the Z-retract position. (To set Z-retract,
first set the DRO at the desired value [X,Y,Z=0]; then press JOG and move Z to +2.0
inches. Then press MODE, press RUN, press SET Z RETRACT then press INC/ABS
SET.) Turn the flat (position A) out of the way so the indicator will not crash into it.
Run the program. After the indicator starts to move away from position A, turn the
flat back into place so the indicator will read position B. After reading position B it will
backup about 4 inches and return to read position B again. Turn the flats out of the
way again to allow the indicator to move beyond position B about 3 inches at which
time it will return to position B. Return the flats to the readable position again to read
the position at B.

Movement 1 A B

Pause. Record indicator reading. Press "Go".

Movement 2 B

Pause. Record indicator reading. Turn flat away from the path of indicator travel. Press
"Go".
177
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Movement 3 B

Pause. Turn flat so position B is readable again. Record indicator reading. End
program.

Movement 1 Positional Accuracy -- Checks the calibration of the machine.

Typical values for a new machine are 0.0005" or less.

Movement 2 Uni-directional Repeatability -- Measures how well the machine

comes back to a point from one direction. Typical values for a new machine are
0.0005" or less.

Movement 3 Bi-directional Repeatability -- Measures how well the machine

comes back to a point from both directions. This value when measured is the
difference between the uni-directional value and the value from the other direction.
Typical values for a new machine are 0.0005" or less.

Example -- If the uni-directional value was -0.0002" and the value from the other
direction is +0.0002", the bi-directional repeatability value is 0.0004".

Other considerations for accuracy or repeatability are: (1) Is it constant? (2) Is it

random? (3) Is it changing at a particular rate. This leads to the possibility of
running the program several times or manually running a repeatability test. For
example: Set the indicator on the flat of position A. Zero the indicator and the DRO.
Move away from the flat about 4 inches then return to read the flat and record the
result. Do this approximately 6 times for positional accuracy/repeatability concerns.
The following is an example for manually checking positional accuracy/repeatability.

i01080-3

5.2.5.2 The Program for the Y-axis Will Run as Follows:

The Y-axis program will function in relatively the same way as the X-axis program.
Set-up is the same except that the Y direction it utilizes a different program file.

178
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
FIGURE 5-47
Typical set-up for a Y-axis accuracy/repeatability check

5.2.5.3 The Program for the Z-axis

1. Place a 75 mm gage block on the table. (One end of the 3.0-inch dimension
in contact with the table and the other end touching off the indicator.) Set a
0.0001" indicator on the spindle and move it to read the top of the 77 mm
gage block.
2. Set the indicator and the DRO X, Y & Z values to zero, and set Z-retract at
this position also. Then press MODE, press RUN, press SET Z RETRACT
then press INC/ABS SET.)
3. To run the program, press MODE, RUN, START, GO.
4. Press GO again and the Z-axis will move to –75 mm and stop. Record
indicator reading. This is your positional accuracy value.
5. Press GO. Z moves up to zero then back down to –75 mm then stops.
Record the change. This is the uni-directional repeatability value.
6. Press GO. Z will move to zero then stop. Move the 75 mm gage block back
into position and note the indicator reading. This movement will yield the
value for bi-directional repeatability. Record the reading. End.

179
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 7. Adjust backlash values as needed.

Figure 5-48
Typical set-up for a Z-axis accuracy/repeatability check

180
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 5-49
Program Movement

181
Southwestern Industries, Inc.
TRAK& Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
6.0 Figures and Parts Lists
Figure 100
Top Housing Assembly – 40 Taper

182
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List - Top Housing Assembly – 24688-1

Item P/N DESCRIPTION Qty

1 20697-1 GEAR HOUSING SUB-ASSY (4VK-A1) 1
2 20697-2 HI-LOW SHIFT CLUTCH SUB-ASSY (4VK-A2) 1
3 20697-3 HI-LOW SHIFT SUB-ASSY (4VK-A3) 1
4 FVS12 SOCKET CAP SCREW M6-P1.0x15L 2
5 20697-4 PULLY PINION SUB-ASSY (4VK-A4) 1
6 FVS64 BULL GEAR PINION BEARING CAP 1
7 FVS93 SCREW SOC HD M5-P0.8x15L 1
8 FVS117 KEY 5x520L 1
9 FVS62 TIMING BELT PULLEY 1
10 FVS126 WASHER Ø 5/8 1
11 FVS61 JAM NUT 5/8-11NC 1
12 20697-5 LOWER VARI-DISC DRIVE SUB-ASSY (4VK-A5) 1
13 FVS63 BELT 8YU-600L 1
14 FVS135 KEY 8x7x60L 1
UPPER VARI-DISC DRIVE SUB-ASSY (4VK-A6) (Shown for
15 20697-6 reference only - See figure 106) 1
16 FVS4 BELT 1
17 FVS1 BELT HOUSING 1
18 FVS17 SOCKET CAP SCREW M6-P1.0x35L 1
19 FVS13 TOP BEARING CAP 1
20 FVS15 BALL BEARING (6909VV) 1
21 FVS129 SCREW- SOC HD CAP M6-P1.0x18L 1
22 20697-7 SPEED CHANGE HANDWHEEL SUB-ASSY (4VK-A7) 1
23 FVS10 SCREW- SOC HD CAP M8-P1.25x30L 1
MOTOR ASSY-DPM5-5HP-WHITE (shown for reference only, not
24 20820-1 part of upper head housing assembly) 1
25 FVS130 WASHER- FLAT Ø 10.2 4
26 FVS111 SOC HD SCREW- 3/8-16NCx32L 4
27 FVS11 MOTOR PULLEY COVER 1
28 FVS104 COPPER CHIP(2REQ.) 2
29 FVS131 SCREW- FLAT HD PHILIP M5-P0.8x10L 1
30 FVS132 STUD Ø 7/16-92L 2
31 FVS133 STUD Ø 7/16-56L 1
32 FVS96 JAM NUT 3/8-16NC 1
33 FVS101 VENTILATOR (2REQ.) 2
34 FVS136 SCREW- SOC HD CAP M6-P1.0x10L 12
35 FVS16-1 VARI-SPEED DIAL 1
36 FVS95 HEX CAP NUT 5/16-18NC 1
37 FVS16-2 NAME PLATE 1
38 FVS19 DRIVE SCREW 1
39 OIL-1 FRU-K3-OIL CUP 1
i00593-K4

183
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 101
Gear Housing Sub-Assembly
P/N: 20697-1

Item P/N Description Qty

1 FVS82 GEAR HOUSING 1
2 FV112 GUIDE SPRING 3
3 FV113 SPRING GUIDE PIN 3
i00594-K4

184
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N DESCRIPTION Qty
1 FVS75 BEARING SLIDING HOUSING 1
2 23943 BEARING-DEEP GROVE U/SET (2)-6910ZZ 1 SET
3 FVS78 BEARING SPACER 1
4 FVS79 BEARING SPACER 1
5 FVS80 SNAP RING R-75 1
6 FVS73 SPLINED GEAR HUB 1
7 FVS72 KEY 8x7x10L 1
8 FVS74 SPINDLE BULL GEAR 1
9 FVS114 WASHER 1
10 FVS115 EXTERNAL TOOTH WASHER Ø 50 1
11 FVS81 LOCK WASHER Ø 50-18NC 1
12 FVS76 RING 1
13 20818 SPACER, BEARING 1
i20697-2

Figure 102
Hi-Low Slip Clutch
Sub-Assembly
P/N: 20697-2

185
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N DESCRIPTION Qty
1 FVS89 HI-LOW DETENT PLATE 1
2 FVS87 CLUTCH GEAR SHAFT 1
3 FVS92 HI-LOW PINION BLOCK 1
4 FVS91 SPRING 1
5 FVS90 HI-LOW DETENT PLUNGER 1
6 FVS94 HI-LOW SHAFT CRANK 1
7 FVS88 PIN Ø 319L 1
8 FVS93 SCREW SOC HD M5-P0.8x15L 3
9 FVS92-1 SET SCREW M5-P0.8x5L 1
10 FVS92-2 WASHER- FLAT Ø 11 1
11 FVS57 BAKELITE BALL HANDLE 1
12 FVS116 WASHER- FLAT Ø 6 1
13 24083 SHAFT HI/LOW SHAFT ASSY 1
i00596-K4

Figure 103
Hi-Low Shift Sub-Assembly
P/N: 20697-3

186
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N DESCRIPTION Qty
1 FVS67 BULL GEAR PINION COUNTER SHAFT 1
2 FVS69 KEY 5518L 1
3 FVS66 BULL GEAR PINION 1
4 AK118 BEARING-DEEP GROOVE-6203ZZ 2
5 FVS3 SOCKET SET SCREW M6-P1.0x6L 1
6 23954 BEARING-DEEP GROOVE-SET (2)-6203ZZ 1
i00597-K4

Figure 104
Pulley Pinion Sub-Assembly
P/N: 20697-4

187
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 105
Lower Vari-Disc Sub-Assembly
P/N: 20697-5 (assembly not available, order parts separately)

188
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List - Lower Vari-Disc Sub-Assembly

Item P/N DESCRIPTION Qty

1 FVS50 BELT HOUSING BASE 1
2 FVS59 BRAKE BLOCK 2
3 FVS58 TURNING BLOCK SHAFT 1
4 FVS103 RETAINING RING Ø 7 1
5 FVS51 SET SCREW M6-P1.06L 2
6 FVS53 BRAKE LOCK BUSHING 1
7 FVS52 BRAKE LOCK SHAFT 1
8 FSV119 RETAINING RING Ø 11 1
9 FVS47 BRAKE SHOE 2
10 FVS48 BRAKE SHOE PIVOT SLEEVE 1
11 FVS17 SOCKET CAP SCREW M6-P1.0x35L 1
12 FVS49 BRAKE SPRING 2
13 FVS122 WASHER Ø 6 4
14 FVS120 SCREW- PHILLIP PAN HD 3/16-24NC6L 4
15 FVS46 BRAKE BEARING CAP 1
16 AK048 BALL BEARING 6912ZZ 1
17 FVS14 SOCKET CAP SCREW M 5-PO.8x12L 4
18 FVS45 STATIONARY DRIVEN VARIDISC 1
19 FVS70 SPINDLE PULLEY ASSY 1
20 FVS100 SPINDLE PULLEY SPACER 1
21 FVS71 KEY 8x8x20L 1
22 FVS97 SNAP RING Ø 50 1
23 FVS52-1 BRAKE LOCK SHAFT SWIVEL 1
24 FVS56 BRAKE LOCK HANDLE 1
25 FVS54 HANDLE FIX BLOCK 3/8-16NC 1
26 FVS55 SPRING PIN Ø 6x20L 1
27 FVS57-1 BAKELITE BALL HANDLE 3/8-16NC 1
28 24055 BRAKE SHOE ASSY 1
29 FVS98 CLUTCH WASHER 1
i00598-K4

189
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 106
Upper Vari-Disc Sub-Assembly
P/N: 20697-6
190
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List - Upper Vari-Disc Sub-Assembly

Item P/N DESCRIPTION Qty

1 FVS44 ADJUSTABLE-DRIVEN VARIDISC 1
2 FVS42 SPINDLE PULLEY BEARING HOUSING 1
3 FVS43 BEARING-DEEP GROVE-6013ZZ 1
4 FVS36 SPEED CHANGE PLATE 1
5 FVS38 PIVOT SLEEVE Ø 5 2
6 FVS37 WASHER M5-P0.8x20L 2
7 FVS3123 SOCKET CAP SCREW 2
8 FVS39 SPEED CHANGE PLATE PIVOT STUD 1
9 FVS41 WASHER Ø 8.2 1
10 FVS40 ROLL PIN Ø3x15L 2
11 FVS35 CHAIN END STUD 1
12 FVS34 ADJUSTMENT NUT 1
13 FVS33 CHAIN FRONT SCREW M4-P0.7x5L 1
14 FVS97 SNAP RING Ø 50 1
15 FVS96 JAM NUT 3/8-16NC 1
16 24599 BEARING HOUSING ASSY-K4 1
17 24603 VARIDISC ASSY-ADJUSTABLE 1
i20697-6

191
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title Qty
1 FVS16 SPEED CHANGE HOUSING 1
2 FVS20 BEARING SELF LUBRICATING 1
3 FVS22 SPEED CHANGER GEAR 1
4 FVS31 SPEED CHANGE CHAIN DRUM 1
5 FVS21 WORM 1
7 FVS25 SPEED CHANGE SHAFT 1
8 FVS40 ROLL PIN Ø3x15L 2
9 FVS24 COPPER BUSHING 2
10 FVS32 CHAIN #3109.525 1
11 FVS31-1 DOWEL PIN Ø3x25L 1
12 FVS30 SPEED CHANGE STUD 1
13 FVS27 SPEED CHANGE HANDWHEEL 1
14 FVS18 FULL DOG SOCKET SET SCREW M6-P1.0x10L 1
15 FVS28 HANDLE 3/8-16NC 1
16 VS24-1 WASHER-WAVE 1
i20697-7

Figure 107
Speed Change Handwheel Sub-Assembly,
P/N: 20697-7

192
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title Qty Notes
1 FVS110 MOTOR 5 HP 1 only available as 20820-1
2 FVS3-1 KEY 6x6x45L 1 only available as 20820-1
3 FVS2 STATIONARY MOTOR VARIDISC 1 only available as 20820-1
4 FVS6 BUSHING 1 available as 24054 or 20820-1
5 FVS5 ADJUSTABLE MOTOR VARIDISC 1 available as 24054 or 20820-1
6 FVS6-1 KEY 7x7x50L 1 available as 24054 or 20820-1
7 FVS8 SPRING FOR VARIDISC MOTOR SHAFT 1 only available as 20820-1
8 FVS9 ADJUSTABLE VARIDISC SPRING COLLAR 1 only available as 20820-1
9 FVS10 SCREW- SOC HD CAP M8-P1.25x30L 1 only available as 20820-1
10 24054 VARIDISC ASSY 1
i00601-K4

Figure 108
Spindle Motor Sub-Assembly
P/N: 20820-1
193
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 109
Bottom Housing Assembly

194
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List - Bottom Housing Assembly
Item P/N Title Qty
1 FB192 QUILL HOUSING 1
2 FB31 CLUSTER GEAR SHAFT 1
3 FB33 BEVEL GEAR BEARING 1
4 FB94 SNAP RING 95 DOWEL PIN Ø 14 1
5 FB29 CLUSTER GEAR KEY 3x3x45L 1
6 FB28 CLUSTER GEARS ASSEMBLY 1
7 FB41 NEEDLE BEARING KO-BA66Z 1
8 FB27 CLUSTER GEAR SHAFT UPPER BEARING 1
9 20698-1 WORM GEAR CRADLE SUB-ASSY (4VK-H1) 1
10 FB19 SHIFT SLEEVE 1
11 FB18 WORM GEAR CRADLE THROW-OUT 1
12 FB20 CAP SCREW M5-P0.8x12L 1
13 FB24 STEEL BALL 1
14 FB25-A SPRING 1
15 FB23 SHIFT CRANK 1
16 FB68 SET SCREW M6-P1.0x8L 1
17 20698-2 QUILL FEED SELECTOR SUB ASSY (4VK-H2) 1
18 FB67 CAP SCREW M6-P1.0x18L 4
19 FB186 WORM GEAR 1
20 FB189 ADJ WORM SHAFT 1
21 FB187 KEY 4x4x18L 1
22 20698-3 SUB-ASSY-QUILL PINION SHAFT-40 TAPER 1
23 FB178 CLOCK SPRING (CLOCK SPRING ASSY.) 1
24 FB177 SPRING COVER 1
26 FB176 PINION SHAFT HUB SLEEVE 1
27 FB171 KEY 3x3x20L 1
28 FB89 OVERLOAD CLUTCH LEVER SPRING PLUNGER 1
29 FB88 COMPRESSION SPRING 1
30 FB88-1 INTERNAL COMPRESSION SPRING 1
31 20698-4 OVERLOAD CLUTCH TRIP SUB-ASSY (4VK-H4) 1
32 FB99 CLUTCH ARM COVER 1
33 FB73 CAP SCREW M5-P0.8x40L 2
35 FB101 CHEM BLACKED LOCKNUT M6-P1.0 1
36 20698-5 FEED REVERSE CLUTCH SUB-ASSY (4VK-H5) 1
37 FB109 KEY 3x3x20L 1
38 FB106 FEED TRIP BRACKET 0
39 FB118 CAM ROD SLEEVE ASSY. 1
40 FB120 COMPRESSION SPRING 1
41 FB121 TRIP PLUNGER 1
42 FB123 TRIP PLUNGER BUSHING 1
43 FB103 CAM ROD 1
44 FB117 ROLL PIN Ø 3x15L 1
45 FB104 TRIP HANDLE 1
46 FB105 BLACK PLASTIC BALL 1
47 FB119-1 ROLL PIN Ø 3x20L 1
48 FB107 CAP SCREW M6-P1.0x25L 2
49 FB113 HAND WHEEL CLUTCH 1
195
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 51 FB115 COMPRESSION SPRING 1
53 FB108 SET SCREW M6-P1.0x8L 1
54 FB42 BUSHING 1
55 20836-1 SPINDLE ASSY-40 TAPER 1
56 FB148 QUILL LOCK SLEEVE TAPPED 1
57 FB148-1A COMPRESSION SPRING 1
58 FB153 QUILL LOCK SLEEVE 1
59 FB152 QUILL LOCK BOLT 1
60 FB149 LOCK HANDLE 1
61 FB149-1 CONICAL COMPRESSIONAL SPRING 1
62 FB149-2 SCREW- PHILLIP HD 1
63 FB175 RACK FEED HANDLE HUB 1
64 FB114 STEEL BALL 2
65 FB175-2A COMPRESSION SPRING 1
66 FB116 HANDWHEEL CLUTCH SPRING SCREW M8-P1.25x6L 2
67 FB175-3 DOWEL PIN 1
68 FB190 PINION SHAFT HUB HANDLE 1
69 FB191 PLASTIC BALL HANDLES 1
70 FB169 SOC HEAD SCREW M5-P0.8x15L 4
71 FB163 QUILL STOP KNOB 1
72 FB200 SCREW- SOC HD 3/8-24NF x 1 1/4 1
73 FB164 QUILL STOP MICRO-SCREW 1
74 FB160 SNAP RING Ø16 1
75 FB161 QUILL MICRO-STOP NUT 1
76 FB162 MICROMETER NUT 1
77 FB184 FEED REVERSE TRIP PLUNGER 1
78 FB183 REVERSE TRIP BALL LEVER 1
79 FB185 REVERSE TRIP BALL LEVER SCREW 1
80 FB202 INDICATOR ROD 1
81 FB201 INDICATOR ROD SCREW 1
82 FB124 FEED TRIP PLUNGER 1
83 FB145 FEED TRIP LEVER 1
84 FB144 SOCKET SET SCREW 1
85 OIL-1 FRU-K3-OIL CUP 1
86 FB125 HANDWHEEL 1
87 FB125-1 HANDWHEEL SPRING PIN - Ø 3x3x10L 1
88 FB125-2 HANDWHEEL HANDLE 1
89 FB111 REVERSE KNOB 1
90 FB100 SOCKET SET SCREW M6-P1.0x20L 2
91 FB124-1 FEED TRIP PLUNGER SOC SET SCREW M4-P0.7x20L 1
92 FB124-2 FEED TRIP PLUNGER NUT M4-P0.7x20L 2
93 FB128 QUILL SKIRT 1
94 FVS109 DRAWBAR 5/8-11NC 1
95 FVS109-1 SPACER 1
96 25041 SCALE-HEAD ROTATION-NT40 1
97 25043 POINTER SCALE 1
98 25044 DRIVE SCREW-SCALE 4
99 20834 FEED REVERSE KNOB ASSY 1
100 20835 HANDWHEEL ASSY 1

196
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
101 24099 TRIP HANDLE ASS'Y (INCLUDES PLASTIC BALL) 1
102 20833 FRU-K4-FEED TRIP ASSY 1
103 20847 QUILL MICRO NUT & SCREW ASSY 1
104 20846 QUILL LOCK HANDLE ASSY 1
105 20850 FEED HANDLE ASSY 1
106 24095 CLOCK SPRING ASSEMBLY (SPRING & COVER) 1
107 20844 QUILL LOCK SLEVE ASSY 1
108 FB142 QUILL 1
T BOLT ASSY (includes A070, A071, A069) (not shown on
109 A071
drawing) 4
i20698

197
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title Qty
1 FB17 WORM GEAR CRADLE 1
2 FB5 WORM CRADLE BUSHING 1
3 FB6 SETSCREW M6-PP1.0x10L 1
4 FB8 FEED DRIVEWORM GEAR 1
5 FB4 FEED WORM GEAR SHAFT SLEEVE 1
6 FB9 FEED DRIVE WORM GEAR SHAFT 1
7 FB11 KEY 3x3x20L 1
8 FB10 WORM SHAFT KEY 3x3x8L 1
9 FB3 FEED BEVEL PINION 1
10 FB2 BEVEL PINION WASHER Ø 5 1
11 FB1 SOC.HD.SCREW M5-P0.8x10L 1
12 FB16 FEED ENGAGE PIN 1
13 FB36 FEED DRIVING GEAR 1
14 FB36-1 KEY 3x3x8L 1
15 FB15 FEED REVERSE BEVEL GEAR 1
16 FB13 WASHER Ø 6 Ø 22 1
17 FB14 SOC HD SCREW M6-P1.0x15L 1
18 FB37 KEY 3x3x10L 1
19 FB40 FEED DRIVE GEAR 1
i00603-K4
Figure 110
Worm Gear Cradle Sub-Assembly
P/N: 20698-1
198
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N DESCRIPTION Qty
1 FB66 CLUSTER GEAR COVER 1
2 FB64 CLUSTER GEAR SHIFT CRANK 1
3 FB69-1 DIAL 1
4 FB69 SHIFT KNOB 1
5 FB71 SPRING 1
6 FB70 STEEL BALL 1
7 FB68 SET SCREW M6-P1.0x8L 1
8 FB63 FEED GEAR SHIFT FORK 1
9 FB60 FEED SHIFT ROD 1
10 FB61 KP.SET SCREW M5-P0.8x6L 1
i00604-K4

Figure 111
Quill Feed Selector Sub-Assembly
P/N: 20698-2

199
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title UseAs Qty
1 FB166 QUILL PINION SHAFT EA 1
3 K-B92 OVERLOAD CLUTCH WORM GEAR EA 1
4 K-B93 OVERLOAD CLUTCH RING EA 1
5 K-B92-1 SCREW SOC HD CAP M4-P0.7x15L EA 3
6 K-B94 SNAP RING 95 DOWEL PIN Ø 14 EA 1
7 K-B168 SCREW PIN EA (1)
8 25707 BUSHING KIT-PINION SHAFT-40 TAPER EA 1
i20698-3

Figure 112
Quill Pinion Shaft Sub-Assembly
P/N: 20698-3

200
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title Qty
1 FB81 OVERLOAD CLUTCH SLEEVE 1
2 FB81-1 KEY 5x8x13L 1
3 FB80 OVERLOAD CLUTCH 1
4 FB79 SAFETY CLUTCH SPRING 1
5 FB78 OVERLOAD CLUTCH LOCKNUT 1
6 FB76 SOCKET SET SCREW M6-P1.0x8L 1
7 FB75 CLUTCH RING 1
8 FB97 OVERLOAD CLUTCH WASHER 1
9 FB98 SNAP RING Ø 10 1
10 FB96 OVERLOAD CLUTCH TRIP LEVER 1
11 FB74 CLUTCH RING PIN (2REQ.) 2
12 FB77 BRASS PLUG 1
i00606-K4

Figure 113
Overload Clutch Trip Sub-Assembly
P/N: 20698-4

201
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title Qty
1 FB57 FEED WORM SHAFT 1
2 FB44 FEED WORM SHAFT BUSHING 1
3 FB47 FEED WORM SHAFT THRUST WASHER 1
4 FB43 WORM 1
5 FB59 PIN Ø 3x12L 1
6 FB49 FEED REVERSE BEVEL GEAR 1
7 FB48 BUSHING 1
8 FB62 KEY 3x3x15L 1
9 FB50 FEED REVERSE CLUTCH 1
10 FB50-1 PIN Ø 3x19L 1
11 FB55 REVERSE CLUTCH ROD 1
12 FB52 BUSHING 1
13 FB51 FEED REVERSE BEVEL GEAR 1
i00607-K4

Figure 114
Feed Reverse Clutch Sub-Assembly
P/N: 20698-5

202
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 115
Quill Spindle Sub-Assembly
P/N: 20836-1

203
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List - Spindle Sub-Assembly

Item P/N DESCRIPTION Qty

1 FB127 SPINDLE BT-40 1
2 FB133 NOSE-PIECE 1
3 FB134 SPINDLE DIRT SHIELD 1
4 20839 BEARING-ANGULAR CONTACT U/ SET (2)-7010 P4 1 Set
5 FB136 BEARING SPACER-LARGE 1
6 FB137 BEARING SPACER-SMALL 1
7 FB139 SPINDLE BEARING KNOCK NUT 1
8 FB139-1 SET SCREW M8-P1.25x6L 2
10 A112H BEARING 6008ZZ 1
11 FB143 LOCK RING Ø 40 1
12 FB140 SPINDLE FIXED NUT 2
13 FB141 COLLET ALIGNMENT SCREW M8-P1.25x20L 2
14 20841 BEARING SPACER SET 1
i00608-K4

204
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 118
Top Housing Assembly – R8

205
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List
Head Top Assembly - 24692

Item P/N Title Qty

1 20778-1 GEAR HOUSING SUB-ASSY (3VK-A1) 1
2 20778-2 HI-LOW SHIFT CLUTCH SUB-ASSY (3VK-A2) 1
3 20778-3 HI-LOW SHIFT SUB-ASSY (3VK-A3) 1
4 VS12 SOCKET CAP SCREW M6-P1.0x15L 2
5 20778-4 PULLY PINION SUB-ASSY (3VK-A4) 1
6 VS64 BULL GEAR PINION BEARING CAP 1
7 VS93 SCREW M5-P0.8x15L 1
8 VS117 KEY 5x525L 1
9 VS62 TIMING BELT PULLEY 1
10 VS126 WASHER Ø 5/8 1
11 VS61 JAM NUT 5/8-11NC 1
12 20778-5 LOWER VARI-DISC DRIVE SUB-ASSY (3VK-A5) 1
13 VS63 BELT 3/8"-#225 1
14 VS14-1 SCREW M8-P1.25x18L 3
15 VS135 KEY 8x7x60L 1
16 VS4 BELT 1
17 20778-6 UPPER VARI-DISC DRIVE SUB-ASSY (3VK-A6) 1
18 VS1 BELT HOUSING 1
19 VS137 SOCKET CAP SCREW M8-P1.25x25L 1
20 VS13 TOP BEARING CAP 1
21 VS13-1 WAVE WASHER 1
22 VS15 BEARING-DEEP GROVE-6007V 1
23 VS129 SCREW- SOC HD CAP M6-P1.0x18L 1
24 20778-7 SPEED CHANGE HANDWHEEL SUB-ASSY (3VK-A7) 1
25 VS07 SCREW- SOC HD CAP M6-P1.0x35L 1
MOTOR ASSY- K2 & K3- 3HP WHITE (reference only, not part of
26 20819-1 upper head housing assembly) 1
27 VS130 WASHER- FLAT Ø 10.2 4
28 VS111 SOC HD SCREW- 3/8-16NCx32L 4
29 VS11 MOTOR PULLEY COVER 1
30 VS104 COPPER CHIP(2REQ.) 2
31 VS131 SCREW- FLAT HD PHILIP M5-P0.8x10L 1
32 VS132 STUD Ø 7/16-100L 2
33 VS96 JAM NUT 3/8"-16NC 1
34 VS101 VENTILATOR(2REQ.) 2
35 VS136 SCREW- SOC HD CAP M6-P1.0x10L 12
36 VS54 HANDLE FIX BLOCK 1
37 VS55 SET SCREW 1
38 VS56 BRAKE LOCK HANDLE 1
39 VS57 BAKELITE BALL HANDLE 1
40 OIL-1 OIL CUP 1
i00690-K2-K3

206
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title Qty
1 VS82 GEAR HOUSING 1
2 VS112 GUIDE SPRING 3
3 VS113 SPRING GUIDE PIN 3
i00691-K2-K3

Figure 119
Gear Housing
P/N: 20778-1

207
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 120
Hi-Low Shift Clutch
Sub-Assembly
P/N: 20778-2

208
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List – High-Low Shift Clutch

Item P/N DESCRIPTION Qty

1 VS75 BEARING SLIDING HOUSING 1
2 23970 BALL BEARING 6908ZZ 1 SET
3 VS78 BEARING SPACER 1
4 VS79 BEARING SPACER 1
5 VS80 SNAP RING R-65 1
6 VS73 SPLINED GEAR HUB 1
7 VS72 KEY 8x7x10L 1
8 VS74 SPINDLE BULL GEAR 1
9 VS114 WASHER 1
10 VS115 EXTERNAL TOOTH WASHER Ø 40 1
11 VS81 LOCK WASHER Ø 9/16-18NC 1
12 VS76 RING 1
13 20817 SPACER-BEARING 1
i00692-K2-K3

209
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 121
Hi-Low Shift
P/N: 20778-3

Item P/N DESCRIPTION Qty

1 VS89 HI-LOW DETENT PLATE 1
2 VS87 CLUTCH GEAR SHAFT 1
3 VS92 HI-LOW PINION BLOCK 1
4 VS91 SPRING 1
5 VS90 HI-LOW DETENT PLUNGER 1
7 VS88 PIN Ø 3X19L 1
8 VS93 SCREW M5-P0.8x15L 2
9 VS92-1 SET SCREW M5-P0.8x5L 1
10 VS92-2 WASHER- FLAT Ø 11 1
12 VS116 WASHER- FLAT Ø M5 1
13 24083 SHAFT-HI/LOW SHAFT ASSY 1
i00693-K2-K3

210
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N DESCRIPTION Qty
1 VS67 BULL GEAR PINION COUNTER SHAFT 1
2 VS69 KEY 5X5X18L 1
3 VS66 BULL GEAR PINION 1
4 AK118 BEARING-DEEP GROOVE-6203ZZ 2
5 VS3 SOCKET SET SCREW M6-P1.0x6L 1
6 23954 BEARING SET (2) BEARING 6203ZZ 1
i00694-K2-K3

Figure 122
Pulley Pinion
P/N: 20778-4

211
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Figure 123
Lower Vari-Disc Drive
P/N: 20778-5

(assembly not available, order parts separately)

212
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List – Lower Vari-Disc Drive
Item P/N DESCRIPTION Qty
1 VS50 BELT HOUSING BASE 1
2 VS59 BRAKE BLOCK 2
3 VS58 TURNING BLOCK SHAFT 1
4 VS103 RETAINING RING Ø 7 1
5 VS51 SET SCREW M6-1.0X6L 2
6 VS53 BRAKE LOCK BUSHING 1
7 VS52 BRAKE LOCK SHAFT 1
8 VS52-2 BRAKE LOCK PIN DIA 3 X 5/8"L 1
9 VS47 BRAKE SHOE 2
10 VS48 BRAKE SHOE PIVOT SLEEVE 1
11 VS17 SOCKET CAP SCREW M6-P1.0x35L 1
12 VS17-1 WASHER Ø 6 1
13 VS17-2 NUT M6-P1.0 1
14 VS49 BRAKE SPRING 2
15 VS122 WASHER DIA 3.3 4
16 VS120 SCREW-PAN HEAD PHILIP 5-40NC 4
17 VS46 BRAKE BEARING CAP 1
18 VS43-1 BALL BEARING 6010ZZ 1
19 VS14 SOCKET CAP SCREW M5-0.8x12L 4
20 VS45 STATIONARY DRIVEN VARIDISC 1
21 VS70 SPINDLE PULLY ASSY 1
22 VS100 SPINDLE PULLY SPACER 1
23 VS71 KEY 8x7x20L 1
24 VS97 SNAP RING Ø 40 1
25 VS50-1 DUST COVER 1
26 VS50-2 SCREW-FH-PH-STL-BO M6-1.0X6L 4
27 24055 BRAKE SHOE ASSY 1
i00695-K2-K3

213
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 124
Upper Vari-Disc Drive Sub-Assy
P/N: 20778-6

214
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List – Upper Vari-Disc Drive Sub-Assy

Item P/N DESCRIPTION Qty

1 VS42 SPINDLE PULLEY BEARING HOUSING 1
2 VS43 BEARING-DEEP GROVE-6210ZZ 1
3 VS44 ADJUSTABLE-DRIVEN VARIDISC 1
4 VS36 SPEED CHANGE PLATE 1
5 VS38 PIVOT SLEEVE Ø 5 2
6 VS37 WASHER M5-P0.8x20L 2
7 VS123 SCREW-SHCS M5-0.8X20L 2
8 VS39 SPEED CHANGE PLATE PIVOT STUD 1
9 VS41 WASHER Ø 8.2 1
10 VS40 ROLL PIN Ø3x15L 2
11 VS35 ADJUSTMENT NUT 1
12 VS34 CHAIN END STUD 1
13 VS33 CHAIN FRONT SCREW M4-P0.7x5L 1
14 VS7 SNAP RING Ø 35 1
15 FVS96 JAM NUT 3/8-16NC 1
16 24564 BEARING HOUSING ASSY 1
17 24631 VARI DISC ADJUSTABLE ASSY 1
i20778-6

215
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N DESCRIPTION Qty
1 VS16 SPEED CHANGE HOUSING 1
2 VS20 BEARING SELF LUBRICATING 1
3 VS22 SPEED CHANGER GEAR 1
4 VS31 SPEED CHANGE CHAIN DRUM 1
5 VS21 WORM 1
7 VS25 SPEED CHANGE SHAFT 1
8 VS40 ROLL PIN Ø3x15L 2
9 VS24 COPPER BUSHING 2
10 VS24-1 WASHER-WAVE 1
11 VS27 SPEED CHANGE HANDWHEEL 1
12 VS18 FULL DOG SOCKET SET SCREW M6-P1.0x10L 1
13 VS28 HANDLE 3/8-16NC 1
14 VS32 CHAIN #310X9.525 1
15 VS31-1 DOWEL PIN Ø3x25L 1
16 VS30 SPEED CHANGE STUD 1
17 VS16-1 SPEED DIAL 1
18 VS95 NUT-ACORN 5/16-18 NC 1
19 VS16-2 NAME PLATE 1
20 VS19 SCREW-DRIVE 4
21 M5-0.8X14 40B SCREW-SOC SET-STL-BO-CUP 1
22 M5-0.8X5 40B SCREW-SOC SET-STL-BO-CUP 1
i20778-7
Figure 125
Speed Change Handwheel
P/N: 20778-7
216
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 126
Spindle Motor
P/N: 20819-1
Item P/N DESCRIPTION Qty Notes
1 VS110 MOTOR 3 HP 1 only available as 20819-1
2 VS3-1 KEY 6x6x45L 1 only available as 20819-1
3 VS2 STATIONARY MOTOR VARIDISC 1 only available as 20819-1
4 VS6 BUSHING 1 available as 23953 or 20819-1
5 VS5 ADJUSTABLE MOTOR VARIDISC 1 available as 23953 or 20819-1
6 VS6-1 KEY 7x7x50L 1 available as 23953 or 20819-1
7 VS8 SPRING FOR VARIDISC MOTOR SHAFT 1 only available as 20819-1
8 VS9 ADJUSTABLE VARIDISC SPRING COLLAR 1 only available as 20819-1
9 VS10 SCREW- SOC HD CAP M8-P1.25x30L 1 only available as 20819-1
10 23953 VARIDISC ASSY-ADJUSTABLE MOTOR 1
i00698-K2-K3

217
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 127
Lower Head Assembly

218
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List – Lower Head Assembly
Item P/N Title Qty
1 K-B125-2 HANDWHEEL HANDLE (AVAILABLE ONLY IN ASSY. 20835) 1
2 K-B113 HAND WHEEL CLUTCH 1
3 K-B117 ROLL PIN Ø3x15L 1
4 K-B103 CAM ROD 1
5 K-B108 SOCKET SET SCREW M6-P1.0x8L 1
6 K-B119-1 ROLL PIN Ø3x20L 1
7 K-B103-1 CAM ROD PIN Ø6x15L 1
8 K-B107 CAP SCREW M6-P1.0x25L 2
9 K-B106 FEED TRIP BRACKET 1
10 20779-4 OVERLOAD CLUTCH TRIP SUB-ASSY (3VK-B4) 1
11 K-B73 SOCKET SET SCREW M6-P1.0x20L 1
12 K-B101 CHEM BLACKED LOCKNUT M6-P1.0 1
13 K-B99 CLUTCH ARM COVER 1
15 20779-2 QUILL FEED SELECTOR SUB-ASSY (3VK-B2) 1
16 K-B67 CAP SCREW M6-P1.0x18L 4
17 K-B29 CLUSTER GEAR KEY 3x3x45L 1
18 K-B27 CLUSTER GEAR SHAFT UPPER BEARING 1
19 K-B28 CLUSTER GEARS ASSEMBLY 1
20 K-B94 SNAP RING 95 DOWEL PIN Ø 14 1
21 K-B32 BEVEL GEAR THRUST SPACER 1
22 K-B33 BEVEL GEAR BEARING 1
23 K-B31 CLUSTER GEAR SHAFT 6602BB 1
24 20779-1 WORM GEAR CRADLE SUB-ASSY (3VK-B1) 1
25 K-B18 WORM GEAR CRADLE THROW-OUT 1
26 K-B19 SHIFT SLEEVE 1
27 K-B25 CAP SCREW(3REQ.) M5-P0.8x12L 3
28 K-B20 GEAR SHIFT PLUNGER 1
29 K-B21 COMPRESSION SPRING 1
30 K-B22 ROLL PIN Ø3x20L 1
31 K-B23 SHIFT CRANK 1
33 K-B186 WORM GEAR 1
34 K-B128 QUILL SKIRT 1
35 K-B189-1 ADJ WORM SHAFT SET SCREW M6-P1.0x6L 1
36 K-B42 BUSHING 2
37 K-B187 KEY 4x4x18L 1
38 K-B189 ADJ WORM SHAFT 1
39 K-B171 KEY 3x3x20L 1
40 K-B178 CLOCK SPRING(CLOCK SPRING ASSY.) 1
41 K-B177 SPRING COVER 1
42 K-B169 RD.HEAD SCREW(2REQ.) M5-P0.8x15L 2
43 K-B170 ROLL PIN 1
44 K-B175-3 SET SCREW M8-P1.25x6L 2
45 K-B175-2 COMPRESSION SPRING 2
46 K-B175-1 STEEL BALL 2
47 K-B176 PINION SHAFT HUB SLEEVE 1
48 K-B175 RACK FEED HANDLE HUB 1
219
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
49 K-B172 PINION SHAFT HUB SEREW 1
50 20836 SPINDLE ASSY-R8 0
51 VS109 DRAWBAR 7/16-20UNF 1
52 VS109-1 SPACER 1
53 K-B191 BLACK PLASTIC BALL HANDLES (sold as assy 20849 only) 1
54 K-B190 PINION SHAFT HUB HANDLE (sold as assy 20849 only) 1
55 K-B148 QUILL LOCK SLEEVE 1
56 K-B148-1 COMPRESSION SPRING 1
57 K-B153 QUILL LOCK SLEEVE TAPPED 1
58 KB-201 INDICATOR ROD SCREW 1
59 K-B149 LOCK HANDLE 1
60 KB-202 INDICATOR ROD 1
61 K-B164 QUILL STOP MICRO-SCREW 1
62 K-B160 SNAP RING Ø16 1
63 K-B124-2 FEED TRIP PLUNGER NUT M40-P0.7 2
64 K-B124-1 FEED TRIP PLUNGER SOC SET SCREW M4-P0.7x20L 1
65 K-B145 FEED TRIP LEVER 1
66 K-B124 FEED TRIP PLUNGER 1
67 K-B185 REVERSE TRIP BALL LEVER SCREW 1
68 K-B144 SOCKET SET SCREW 1
69 K-B183 REVERSE TRIP BALL LEVER 1
70 K-B161 QUILL MICRO-STOP NUT 1
71 K-B162 MICROMETER NUT 1
72 K-B123 TRIP PLUNGER BUSHING 1
73 K-B184 FEED REVERSE TRIP PLUNGER 1
74 K-B121 TRIP PLUNGER 1
75 K-B120 COMPRESSION SPRING 1
76 K-B158 CHEM BLACKED RD.HD.SCREWS(2 REQ.) M5-P0.8x8L 2
77 K-B118 CAM ROD SLEEVE ASSY 1
78 K-B159 MICROMETER SCALE 1
79 KB-200 SCREW- SOC HD 3/8-24NFx15L 1
80 K-B163 QUILL STOP KNOB 1
81 20779-5 FEED REVERSE CLUTCH SUB-ASSY (3VK-B5) 1
82 OIL-1 OIL CUP 1
83 K-B109 KEY 3x3x20L 1
84 K-B17-1 WORM GEAR SET SCREW M6-P1.0x8L 1
85 K-B88-1 COMPRESSION SPRING 1
86 K-B89 OVERLOAD CLUTCH LEVER SPRING PLUNGER 1
87 20779-3 SUB - ASSY - QUILL PINION SHAFT - R8 1
88 K-B167 KEY 5x5x25L 1
89 K-B27-1 SET SCREW M6-P1.0x8L 1
90 K-B41 NEEDLE BEARING BA66 BEARING SIZE KO-BA66Z 1
91 K-B192 QUILL HOUSING 1
92 K-B104 TRIP HANDLE 1
93 K-B105 BLACK PLASTIC BALL 1
94 K-B125-1 HANDWHEEL SPRING PIN Ø3x3x10L 1
95 K-B125 HANDWHEEL 1
96 K-B111 REVERSE KNOB 1
97 K-B100 CAP SET SCREW M5-P0.8x35L 3
220
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
98 25042 SCALE-HEAD ROTATION-R8 1
99 25043 POINTER SCALE 1
100 25044 DRIVE SCREW-SCALE 4
101 20835 HANDWHEEL ASSY 1
102 20834 FEED REVERSE KNOB ASSY 1
103 24052 TRIP HANDLE ASSEMBLY (INCLUDES PLASTIC BALL) 1
104 20832 FEED TRIP ASSY 1
105 20847 QUILL MICRO NUT & SCREW ASSY 1
106 24051 CLOCK SPRING ASSEMBLY (SPRING & COVER) 1
107 20849 FEED HANDLE ASSY (QUILL HANDLE) 1
108 20843 QUILL LOCK SLEVE ASSY 1
109 K-B142 QUILL 1
110 K-B155 T BOLT ASSY (not shown on drawing) 1
i20779

221
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title Qty
1 K-B17 WORM GEAR CRADLE 1
2 K-B07 WORM GEAR SPACER 1
3 K-B08 FEED DRIVEWORM GEAR 1
4 K-B05 WORM CRADLE BUSHING 1
5 K-B04 FEED WORM GEAR SHAFT SLEEVE 1
6 K-B09 FEED DRIVE WORM GEAR SHAFT 1
7 K-B11 KEY 3x3x25L 1
8 K-B10 WORM SHAFT KEY 3x3x8L 1
9 K-B03 FEED BEVEL PINION 1
10 K-B02 BEVEL PINION WASHER Ø 5 1
11 K-B01 SOC.HD.SCREW M5-P0.8x10L 1
12 K-B36 FEED DRIVING GEAR 1
13 K-B36-1 KEY 3x3x8L 1
14 K-B15 FEED REVERSE BEVEL GEAR 1
15 K-B13 WASHER Ø 6, 22 OD 1
16 K-B14 SOC HD SCREW M6-P1.0x15L 1
17 K-B37 KEY 3x3x10L 1
18 K-B40 FEED DRIVE GEAR 1
19 K-B16 FEED ENGAGE PIN 1
20 K-B06 SETSCREW M6-P1.0x6L 1
i00700-K2-K3
Figure 128
Worm Gear Cradle
P/N: 20779-1
222
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title Qty
1 K-B66 CLUSTER GEAR COVER 1
2 K-B64 CLUSTER GEAR SHAFT CRANK 1
3 K-B70 SHIFT CRANK 1
4 K-B69 SPRING Ø 3 x 20L 1
5 K-B68 GEAR SHIFT PLUNGER 1
6 K-B72 SHIFT KNOB-5/16-18NC 1
7 K-B71 ROLL PIN Ø 3 x 20L 1
8 K-B63 FEED GEAR SHIFT FORK 1
9 K-B65 SHAFT 1
10 K-B61 CAP SET SCREW M5-P0.8x5L 1
i00701-K2-K3

Figure 129
Quill Feed Selector
P/N: 20779-2

223
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title UseAs Qty
1 K-B166 QUILL PINION SHAFT EA 1
2 25706 BUSHING KIT-PINION SHAFT-R8 EA 1
3 K-B91 WASHER EA 1
4 K-B92 OVERLOAD CLUTCH WORM GEAR EA 1
5 K-B93 OVERLOAD CLUTCH RING EA 1
6 K-B92-1 SCREW SOC HD CAP M4-P0.7x15L EA 3
7 K-B94 SNAP RING 95 DOWEL PIN Ø 14 EA 1
8 K-B168 SCREW PIN EA (1)
i20779-3

Figure 130
Quill Pinion Shaft
P/N: 20779-3

224
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title Qty
1 K-B81 OVERLOAD CLUTCH SLEEVE 1
2 K-B81-1 KEY 5x8x13L 1
3 K-B80 OVERLOAD CLUTCH 1
4 K-B79 SAFETY CLUTCH SPRING 1
5 K-B78 OVERLOAD CLUTCH LOCKNUT 1
6 K-B76 SOCKET SET SCREW M6-P1.0x8L 1
7 K-B75 CLUTCH RING 1
8 K-B97 OVERLOAD CLUTCH WASHER 1
9 K-B98 SNAP RING Ø 10 1
10 K-B96 OVERLOAD CLUTCH TRIP LEVER 1
11 K-B74 CLUTCH RING PIN (2REQ.) 2
12 K-B77 BRASS PLUG 1
i00703-K2-K3

Figure 131
Overload Clutch Trip
P/N: 20779-4

225
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N Title Qty
1 K-B57 FEED WORM SHAFT 1
2 K-B47 FEED WORM SHAFT THRUST WASHER 1
3 K-B44 FEED WORM SHAFT BUSHING 1
4 K-B43 WORM 1
5 K-B59 PIN Ø 3x12L 1
6 K-B49 FEED REVERSE BEVEL GEAR 1
7 K-B48 BUSHING 1
8 K-B62 KEY 3x3x15L 1
9 K-B50 FEED REVERSE CLUTCH 1
10 K-B56 PIN Ø 3x19L 1
11 K-B51 FEED REVERSE BEVEL GEAR 1
12 K-B52 BUSHING 1
13 K-B55 REVERSE CLUTCH ROD 1
i00704-K2-K3

Figure 132
Feed Reverse Clutch
P/N: 20779-5

226
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Item P/N DESCRIPTION Qty
1 K-B127 SPINDLE R8 1
2 K-B134 SPINDLE DIRT SHIELD 1
3 20838 BEARING-ANGULAR CONTACT-U/SET(2)-7207 P4 1 SET
4 K-B136 BEARING SPACER-SMALL 1
5 K-B137 BEARING SPACER-LARGE 1
7 K-B133 NOSE-PIECE 1
8 K-B132 SLEEVE 1
9 K-B131 BEARING-DEEP GROVE-6206ZZ 1
10 K-B130 BEARING LOCKWASHERØ 30 1
11 K-B129 SPINDLE BEARING LOCK NUT- Ø30-20N 1
12 K-B150-1 STRAIGHT LOWER CLAMP 1
13 K-B151 FELT OIL STRAINER 1
14 K-B150-2 STRAINER UPPER CLAMP 1
15 K-B139 SCREW-PH-HD-M5-0.8X8L 2
16 20840 BEARING SPACER SET 1
i00705-K2-K3
Figure 133
Spindle Assembly
P/N: 20836

227
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
TRM, DPM, Sport B3, & DPMS3

Figure 134 - Head Top Housing

228
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List, Head Top Housing – P/N 20752R
Item P/N DESCRIPTION Qty ASSY #
1 AK001H BELT HOUSING ASSY (SPECIAL ORDER) 1
2 AK003H GEAR HOUSING (SPECIAL ORDER) 1
3 AK004H FIXED CLUTCH BRACKET 1
4 AK005H SPEED CHANGER HOUSING 1
5 AK006K MOTOR PULLEY COVER (SPECIAL ORDER) 1
6 16501 MOTOR VARI-DISC ASSY (AK007) 1
7 AK014-1 GREASE CAP 1
8 AK016 STUDS 7/16 THREAD-SHORT 3
9 AK019 STUDS 7/16 THREAD-LONG 3
10 AK022 OIL CUP 1
11 AK042L TOP BEARING CAP 1
13 AK045L SPINDLE PULLEY HUB 1
14 AK046 CLUTCH SLEEVE 1
15 AK067 ROLL PIN 1
16 AK068K SPEED CHANGE CHAIN STUD 1
17 AK069 SPEED CHANGER CHAIN 1
18 AK071 BOSTON WORM GEAR 1
19 AK072 ROLL PIN 1
20 AK073H SPEED CHANGE SHAFT 1 16517
21 AK076 SPEED CHANGE HANDWHEEL 1 16517
22 AK080 HANDLE 1 16517
23 AK082 PIN 1
24 AK083 SPEED CHANGER CHAIN DRUM 1
25 AK084 SPEED CHANGER SPUR GEAR 1
26 AK085 KEY 3X3X8 1
27 AK086 PIN 1
28 AK087 HEX CAP NUT 1
29 AK088 PLATE-CAUTION 1 16517
30 AK092 SET SCREW 1
31 AK100L SPINDLE BULL GEAR ASSY 1 16514
32 AK101L SPINDLE GEAR HUB 1 16514
33 AK102 KEY 8X8X12 1 16514
34 AK103L LOCK WASHER 1 16514
35 AK103L-1 COLLAR 1 16514
36 AK104L NUT 1 16514
37 AK105L BEARING SLEEVE 1 16514
38 AK106L BEARING GEAR SLEEVE WASHER 1 16514
BEARING-DEEP GROVE U/SET (2)- 6910ZZ
39 23943 (AK109L) 1 16514
40 AK110L BULL GEAR BEARING SPACER 1 16514/16529
41 AK111L SLEEVE 1 16514/16529
42 AK113 COMPRESSION SPRING 3 16514
43 AK114 BULL GEAR PINION COUNTER SHAFT 1 16515
44 AK115 KEY 5X5X18 1 16515
45 AK116 KEY 5X5X11.5 1 16515
46 AK117 BULL GEAR PINION 1 16515
47 23954 BEARING-DEEP GROOVE-SET (2)-6203ZZ (AK118) 1 16515
48 AK119 PULLEY- TIMING 1
49 AK120 JAM NUT 1
229
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
50 AK121 BELT 1
51 AK121L SNAP RING 1 16514
52 AK122 BULL GEAR PINION BEARING CAP 1
53 AK136 BULL GEAR SHIFT PINION 1 16516
54 AK137 HI-LOW DETENT PLATE 1 16516
56 AK141 HI-LOW PINION BLOCK 1 16516
57 AK142 ROLL PIN 2 16516
58 AK143 SPRING 1 16516
59 AK144 HI-LOW DETENT PLUNGER 1 16516
60 AK145 HI-LOW SHIFT CRANK 1 16516/23912
61 AK146 BAKELITE BALL HANDLE 1 16516/23912
SPACER-BULL GEAR BEARING SPACER &
62 16529 SLEEVE 1
63 23912 HI/LOW SHAFT ASSEMBLY 1
64 AK162K-1 NAMEPLATE 1
65 AK157L VARI-SPEED DIAL 1
66 16517 DPM-SPINDLE SPEED HANDWHEEL ASSY 1
67 16514 DPM-LOW RANGE BULL GEAR ASSY 1
68 16515 DPM-LOW RANGE PINION ASSY 1
69 16516 DPM-LOW RANGE PINION ASSY 1
70 AK075 SCREW-SET 1 16517
71 20752 UPPER HEAD ASSY 1
i00105

230
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 135 - Head Back Gear TRM, DPM, Sport B3 & DPMS3

231
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List – Head Back Gear
Item P/N DESCRIPTION Qty Assy #
1 AK001H BELT HOUSING ASSY (SPECIAL ORDER) 1
2 AK002K BELT HOUSING BASE 1
3 AK003H GEAR HOUSING (SPECIAL ORDER) 1
4 AK006K MOTOR PULLEY COVER 1
5 AK007 MOTOR 3 HP- 4P 3PH (not sold separately) 1 16501
7 AK030 KEY FOR STATIONARY VARIDISC MOTOR SHAFT 1 16501
8 AK032 STATIONARY VARIDISC (NEW) (KEY NOT INCLUDED) 1 16501
9 AK036 ADJUSTABLE VARIDISC ASSY-WITH KEY (AK037) 1 16501
10 AK037 KEY 8x7x55 0 16501
11 AK039 SPRING 1 16501
12 AK042L TOP BEARING CAP 1
13 25719 BEARING-DEEP GROVE-6009ZZ 1
14 AK045L SPINDLE PULLEY HUB 1
15 AK047 SPINDLE PULLEY SPACER 1
16 AK048 OR 24640 BEARING-DEEP GROOVE-6912ZZ 1
17 AK049L BRAKE BEARING CAP 1
18 AK051L STATIONARY DRIVEN VARIDISC 1
19 AK053L SNAP RING 1
ADJUSTABLE-DRIVE VARIDISC (includes AK055 &
20 AK054L AK056) 1
21 AK055 KEY - 8 x 7 x 20 (INCLUDED IN AK054L) 1 AK054L
22 AK056 PIN (INCLUDED IN AK054L) 1 AK054L
23 FVS43 OR 2464 BEARING-DEEP GROVE-6013ZZ 1 16522-2
24 AK059L SPINDLE PULLEY BEARING SLIDING HOUSING 1 16522-2
25 AK061 PIVOT SLEEVE 2
26 AK062 SPEED CHANGE PLATE 1
27 AK063 SPEED CHANGE PLATE PIVOT STUD 1
28 AK067 ROLL PIN 1
29 AK068K SPEED CHANGE CHAIN STUD 1
31 AK095 BRAKE SHOE ASSY (NOT SOLD SEPARATELY) 1 25059
32 AK096 HEX HD SCREW 1
33 AK097 PIVOT SLEEVE 1 25059
35 AK099 BRAKE SPRING 2 25059
36 AK099A GUIDE PIN FOR SPRING 4 25059
38 AK124 BAKELITE BALL HANDLE 1 16520
39 AK125 BRAKE LOCK HANDLE 1 16520
40 AK126 BRAKE LOCK PIN 1 16520
41 AK128H BRAKE LOCK SHAFT 1
42 AK129H SLEEVE FOR BRAKE LOCK SHAFT 1
44 AK131 SNAP RING 1
45 AK132 BRAKE OPERATING FINGER 2
46 AK133 BRAKE FINGER PIVOT STUD 1
47 AK134 SNAP RING 1
48 AK147L DRAWBAR 1 16528
49 AK149L SLEEVE 1 16528
50 AK158 BELT 1
51 AK041K SNAP RING 1 16501
52 AK127 SCREW-SET (M5x.8) 1
232
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
53 16520 BRAKE HANDLE ASSY. 1
54 16528 DRAWBAR & SLEEVE (MANUAL) 1
55 16522-2 HOUSING-BEARING HOUSING ASSY(NEW) 6013 1
57 16501 MOTOR/VARIDISC ASSY 1
58 25059 BRAKE SHOE ASS'Y (NOT SOLD SEPARATELY) 1
59 AK037-1 ROLL PIN 1 16501
60 AK040K ADJUSTABLE VARIDISC SPRING COLLAR 1 16501
61 M6X1.0X20 25B SCREW-SHCS-STL-BO 6
62 M8X1.25X20 25B SCREW-SHCS-STL-BO 6
63 M5X0.8X15 25B SCREW-SHCS-STL-BO 3
64 3/8-16 50B NUT-HEX-STL-BO 1
i00106-1

233
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 136 - Head Lower Housing TRM, DPM, Sport B3,
DPMS3

234
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List – Head Lower Housing
Item P/N DESCRIPTION Qty ASSY #
1 A012H QUILL HOUSING (SPECIAL ORDER ONLY) 1
2 A042H SHIFT CRANK 2 16507/16526
3 A042H-1 PLUNGER 2 16507/16526
4 A042H-4 COMPRESSION SPRING 2 16507/16526
5 A042H-5 BALL 2 16507/16526
6 A045 CLUSTER GEAR SHIFT CRANK 1 16507
7 A047 FEED GEAR SHIFT FORK 1 16507
8 A048 CLUSTER GEAR COVER 1 16507
9 A049 FEED SHIFT ROD 1 16507
10 A053 CLUSTER GEAR SHAFT 1
11 A054 BEVEL GEAR BEARING 1
12 A055 BEVEL GEAR THRUST SPACER 1
13 A056 SNAP RING 2
14 A060 CLUSTER GEAR KEY 1
15 A062 CLUSTER GEAR SHAFT UPPER BEARING 1
16 A063 CLUSTER GEARS ASSY 1
17 A065 QUILL STOP KNOB 1
18 A066 REVERSE TRIP BALL LEVER SCREW 1
19 A067 REVERSE TRIP BALL LEVER 1
20 A068 QUILL STOP MICRO-SCREW 1 16513
23 A071 T-BOLT ASSY 4
24 A073 MICROMETER SCALE 1
25 A074 MICROMETER NUT 1 16513
26 A075 QUILL MICRO-STOP NUT 1 16513
27 A076 SNAP RING 1 16513
28 A078 TRIP LEVER PIN 1
29 A079 FEED TRIP LEVER 1
30 A080 FEED TRIP PLUNGER 1
31 A082 TRIP PLUNGER 1 16508
32 A083 ROLL PIN 2 16508
33 A084 COMPRESSION SPRING 1 16508
34 A085 CAM ROD SLEEVE ASSY 1 16508
35 A086 ROLL PIN 1 16508
36 A087L CAM ROD 1 16508
37 A089 TRIP HANDLE 1 23913/16508
38 A092 FEED TRIP BRACKET 1 16508
39 A094 CLUTCH ARM COVER 1
40 A096H OVERLOAD CLUTCH TRIP LEVER 1
41 A098 PIN 1 16508
42 A098-1 BLACK PLASTIC BALL 1 23913/16508
43 A101H-1 DRIVE KEY 2 16502
44 A102H NOSE PIECE #40 1 16502
45 A102L-3 SET SCREW 1 16502
46 A103L SPINDLE DIRT SHIELD 1 16502
47 A104L QUILL SKIRT 1
20839
48 (A105L) BEARING-ANG CT U/SET (2)-7010-P4 1 16502
49 A106L BEARING SPACER-LARGE 1 16502
235
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
50 A107L BEARING SPACER-SMALL 1 16502
51 A109H QUILL 1 16502
52 A110H SPINDLE #40 (NOT FOR SALE) 1 16502
26392
53 (A112H) BEARING-DEEP GROVE-6008ZZ 1 16502
54 A113H SNAP RING 1 16502
55 A114H LOCKNUT 1 16502
56 A114H-1 SPECIAL SOCKET SET SCREW 1 16502
57 A114H-2 WASHER 1 16502
58 A154 WORM GEAR 1
59 A155 TRM-KEY 1
60 A156H TRM-WORM SHAFT 1
61 A164 BLACK PLASTIC BALL HANDLE 1 16506
62 A165 PINION SHAFT HUB HANDLE 1 16506
63 A166 BACK FEED HANDLE HUB 1 16506
64 A167 PINION SHAFT HUB SCREW 1 16505
65 A168 PINION SHAFT HUB SLEEVE 1
66 A169 KEY 1
67 A170 BALL 1 16506
68 A170A COMPRESSION SPRING 1 16506
69 A173 CLOCK SPRING 1 16504
70 A174 SPRING COVER 1 16504
71 A176 QUILL PINION SHAFT BUSHING 2 16505
72 A176-1 SNAP RING 1
73 A177 PINION SHAFT WORM GEAR SPACER 1
74 A178 OVERLOAD CLUTCH WORM GEAR 1
75 A180 OVERLOAD CLUTCH RING 1 16512
76 A181 OVERLOAD CLUTCH 1 16512
78 A182L QUILL PINION SHAFT 1 16505
79 A183 SAFETY CLUTCH SPRING 1 16512
80 A185 PLUG-BRASS 1 16512
81 A186 OVERLOAD CLUTCH LOCKNUT 1 16512
82 A187 CLUTCH RING 1 16512
83 A188 CLUTCH RING PIN 1 16512
84 A189 SNAP RING 1 16512
85 A190 OVERLOAD CLUTCH SLEEVE 1 16512
86 A190A KEY 1 16512
87 A192L WASHER 1 16511
88 A193L FEED DRIVE WORM GEAR SHAFT 1 16511
89 A196L FEED WORM GEAR SHAFT SLEEVE 1 16511
90 A197L WORM CRADLE BUSHING 1 16511
91 A198L WORM GEAR SPACER 1 16511
92 A199L FEED DRIVE WORM GEAR 1 16511
93 A200 WORM SHAFT KEY 1 16511
94 A202L WORM GEAR CRADLE 1 16511
95 A203 FEED ENGAGE PIN 1 16511
96 A206H WORM GEAR CRADLE THROW-OUT 1 16519
97 A208H SHIFT SLEEVE 1 16519
102 A217 FEED REVERSE BEVEL GEAR 1 16511
103 A217H CLUSTER GEAR KEY 1 16511
104 A218H FEED DRIVING GEAR 1 16511
236
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
105 A221H FEED DRIVE GEAR 1 16511
106 A222H KEY 1 16511
107 A223 BEARING-NEEDLE 1
108 A224 HANDLE 1 16509
109 A225 HANDWHEEL 1 16509
110 A226 FEED REVERSE KNOB STUD 1 16525
111 A227 REVERSE KNOB 1 16525
112 A228 SNAP RING 1 16525
113 A230 KEY 1
114 A231H REVERSE CLUTCH ROD 1
115 A232H FEED WORM SHAFT 1
116 A233 HANDWHEEL CLUTCH 1
117 A235-1 FEED WORM SHAFT THRUST WASHER 1
118 A235L BUSHING 1
119 A236 FEED WORM SHAFT BUSHING 1
120 A237 WORM 1
121 A238 PIN 1
122 A239 BUSHING 1
123 A240 PIN 1
125 A242 KEY 1
126 A241 FEED REVERSE BEVEL GEAR 2
127 A243 ROLL PIN 1
128 A244 FEED REVERSE CLUTCH 1
129 A245 FEED REVERSE BEVEL GEAR 1
130 A246H LOCK HANDLE 1 16527
131 A247H QUILL LOCK SLEEVE 1
132 A248H QUICK LOCK BOLT 1 16527
133 A267 COMPRESSION SPRING 1
134 A269 STEEL BALL 1
135 A270 OVERLOAD CLUTCH WASHER 1 16512
136 A273 SNAP RING 1 16512
137 A274 FEED REVERSE TRIP PLUNGER 1
138 A276 TRIP PLUNGER BUSHING 1
139 A277 OVERLOAD CLUTCH LEVER SPRING PLUNGER 1
140 A278 COMPRESSION SPRING 1
141 16502 DPM-SPINDLE ASSY 1
142 16506 DPM-QUILL HANDLE ASSY 1
143 16507 DPM-FEEDRATE SELECTOR ASSY 1
144 16509 DPM-FEED HANDWHEEL ASSY 1
145 16525 DPM-TRM ASSY-FEED REVERSE KNOB 1
146 16526 DPM-TRM ASSY-SHIFT CRANK 2
147 16527 DPM-LOCK HANDLE AND BOLT 1
148 16503 SPINDLE/QUILL ASSY 1
149 16504 CLOCK SPRING ASSY 1
150 16511 FEED CRADLE ASSY 1
151 16512 FEED CLUTCH ASSY 1
152 16513 MICRO SCREW ASSY 1
153 16519 HANDLE-FEED ENGAGE HANDLE ASSY 1
154 16521 FEED REVERSE KNOB ASSY 1
155 23913 TRIP HANDLE ASSEMBLY 1
156 16505 FRU-DPM-QUILL PINION ASSY 1
237
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
157 16508 FRU-DPM-FEED TRIP ASSY 1
158 M5-.8X15 SCREW 1
159 3/8-24X1 1/4 SCREW 1
i00107

238
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Lubrication Drawings - TRM - Lubrication System

Figure 137 Lubrication System TRM

239
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
DPM, Sport B3 & Sport B5 – Lubrication System

Figure 138 Lubrication System

DPM, Sport B3 & Sport B5

240
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Lubrication System Parts List – DPM, Sport B3 & Sport B5
QTY. PART NO. DESCRIPTION
1 L002 RAM MANIFOLD (A-7)
2 L003 LUB MACHINE COUPLING SET (PH-401, PA-4, PB-4)
14 L004 LUB MANIFOLD COUPLING (SS-2)
- L005 LUB TUBING
1 L006 SADDLE MANIFOLD (A-10)
1 L007 FLEXIBLE LUB HOSE, RAM (φ4 X 300 LG)
1 L008 FLEXIBLE LUB HOSE, SADDLE (φ6 X 700 LG) (4 X 700 LG)
1 L009 OIL FEEDING SYSTEM (CEA-2 φ X 110V)
1 L010 OIL REGULATING DISTRIBUTOR (B-2 φ4)
2 L011 TWIN JOINT SET (JD-4, PA-4, PB-4)
1 L012 T-JOINT SET (PKD-4, PA-4, PB-4)
2 L013 THIMBLE SET (PA-4, PB-4)
14 L014 SCREW NUT (R-08, PB-4)
2 L015 PLUG (PG-004)
1 16530 OILER COVER

241
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 DPM5, DPMS3 & DPMS5 – Lubrication System

Figure 139
Lubrication, Pump,
& Ram
DPM5, DPMS3,
DPMS5
242
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List Lubrication, Pump & Ram
DPM5, DPMS3, DPMS5
Item P/N Description Qty
1 21157-1 LUBRICATION PUMP-DPM5 0
3 B-3 DISTRIBUTOR-OIL REGULATING B-3 0
4 PG004 PLUG- M8 X 1.0 0
5 PA4 BUSHING 13
6 PB4 SLEEVE-4 MM 19
8 PAN4 NUT 6
10 JD-4 2-WAY JUNCTION 1
11 FHC407 TUBE- STEEL ROPE & HOSE 1
12 DB7 DISTRIBUTOR 1
13 PSS4 OIL DISTRIBUTOR 6
14 A4 TUBING-4MM ALUM A/R
16 PZ0204 CLAMP 1
17 PZ0104 CLAMP 1
18 PD401 ADAPTER 3
19 PD408 ADAPTER 1
20 16532 OILER GAUGE DIAL 1
I00661

243
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 140 Lubrication, X & Y Axis – DPMS3

244
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List - Lubrication – X & Y Axis – DPMS3

Item P/N Description Qty

1
2 PH4-8 ELBOW 1
3
4 L015 PLUG- M8 X 1.0-PG004 2
5 L013 BUSHING-PA4 11
6 L014 SLEEVE-4 MM-PB4 11
7
8
10 L012 TEE ADAPTER-PKD4 1
11 L008 HOSE 1
12 L006 DISTRIBUTOR-DB10 1
13 PSS4 OIL DISTRIBUTOR 8
14 L005 TUBING-4MM ALUM-A4 XX
15
i00783-V3-PL

245
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 141 Lubrication System, X & Y Axis
DPM5 & DPMS5

246
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
 Parts List – Lubrication System, X & Y Axis – DPM5
NO. P/N DESCRIPTION QTY
1 CHAIN 10MM X 10MM X 34 UNITS 2
4 PG004 PLUG-M8x1.0 1
5 PA4 BUSHING 23
6 PB4 SLEEVE, Ø4 37
8 PAN4 NUT 14
10 PKD4 3-WAY JUNCTION 3
12 DB8 DISTRIBUTOR 2
13 PSS4 OIL DISTRIBUTOR 14
14 A4 Ø 4 ALUM. TUBING A/R
16 21738 BRACKET- X & Y AXIS LUBRICATION 1
17 21736 BRACKET- X AXIS CHAIN GUIDE 1
18 21737 BRACKET- X & Y AXIS LUBRICATION 1
19 PD408 ADAPTER- 8
20 PH408 ADAPTER- RIGHT ANGLE 6
21 PQ8T NIPPLE- M8 1
22 PZ0104 CLAMP 1
23 M5 P0.8x10 SCREW- PAN HD PHILLIPS 1

Parts List – Lubrication Drawing, X & Y Axis – DPMS5

Item P/N Description Qty
1 P8011010 CHAIN 10MM X 10MM X34 UNITS 1
2 P8621010 CHAIN 10MM X 10MM X42 UNITS 1
4 PG004 PLUG- M8 X 1.0 1
5 PA4 BUSHING 21
6 PB4 SLEEVE-4 MM 35
8 PAN4 NUT 14
10 JD-4 2-WAY JUNCTION 2
12 DB8 DISTRIBUTOR 2
13 PSS4 OIL DISTRIBUTOR 14
14 A4 TUBING-4MM ALUM 144
15 P04 TUBING-4MM PLASTIC 108
16 23254 BRACKET- X & Y AXIS LUBRICATION 1
17 22346 BRACKET- LUBE X-AXIS BALL SCREW 1
18 21737 BRACKET- X & Y AXIS LUBRICATION 1
19 PD408 ADAPTER 2
20 PH408 ADAPTER- RIGHT ANGLE 13
22 PZ0104 CLAMP 1
23 M5-0.8X10 10B SCREW-PH-PHIL-STL-BO 1
24 PH4-8 CONNECTOR- 1
25 M8-1.25X25 25B SCREW-SHCS-STL-BO 2
26 M6-1.0X16 20B SCREW-RH-PHIL-STL-BO 2
i00662

247
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
DPME2 – Lubrication System
Figure 142 Pump & Lube System

248
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List – Lubrication, Pump & Lube System – DPME2
Item P/N Description Qty
21157-1 = blue
1 21157-1 = green LUBRICATION PUMP-DPME2 0
3 B-3 OIL-OIL REGULATING B-3 0
4 PG004 PLUG- M8 X 1.0 0
5 PA4 BUSHING 13
6 PB4 SLEEVE-4 MM 19
8 PAN4 NUT 6
10 JD-4 2-WAY JUNCTION 1
11 L008 TUBE- STEEL ROPE & HOSE 1
12 DB7 DISTRIBUTOR 1
13 PSS4 OIL DISTRIBUTOR 6
14 A4 TUBING-4MM ALUM A/R
16 PZ0204 CLAMP 1
17 PZ0104 CLAMP 1
18 PD401 ADAPTER 3
19 PD408 ADAPTER 1

249
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 143 Lubrication Drawing, X & Y Axis – DPME2

Item P/N Description Qty

1
2 PH4-8 ELBOW 1
3
4 L015 PLUG- M8 X 1.0-PG004 1
5 L013 BUSHING-PA4 9
6 L014 SLEEVE-4 MM-PB4 9
7
8
10 L012 TEE ADAPTER-PKD4 1
11 FHC405 HOSE 1
12 L006 DISTRIBUTOR-DB10 1
13 PSS4 OIL DISTRIBUTOR 6
14 L005 TUBING-4MM ALUM-A4 XX
15
i00783-E2

250
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Figure 144 Head/Ram Riser Drive System -- TRM

251
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Parts List, Head/Ram Riser Drive System (for Figure 6-45)
| QTY. | PART NO. | DESCRIPTION |
| 1 | B001 | Ram Riser, Feed Nut Bracket |
| 1 | B002 | Ram Riser Nut--Top |
| 1 | B003 | Ram Riser Nut--Bottom |
| 1 | B004 | Ram Riser Screw |
| 1 | B005 | Bearing--62042 |
| 1 | B006 | Ram Riser Top Bracket |
| 1 | B007 | Bearing--51104 |
| 1 | B008 | Nut--AN04 |
| 1 | B009 | Bearing Protector |
| 2 | B010 | Bearing--30205 |
| 1 | B011 | Ram Riser Screw Lower Bracket |
| 2 | B012 | Nut--AN05 |
| 1 | B013 | DC Motor Seat |
| 1 | B014 | Gear Box |
| 1 | B015 | Screw Gear Shaft |
| 1 | B016 | Bearing--60092 |
| 1 | B017 | Bevel Angle Spur Gear |
| 1 | B018 | Bearing--6004Z |
| 1 | B019 | Bevel Angle Spur Gear |
| 1 | B020 | Bearing--6006Z |
| 1 | B021 | Screw Gear Bearing Cover |
| 1 | B022 | Riser Transfer Shaft |
| 1 | B023 | Riser Transfer Shaft Bracket |
| 2 | B024 | Bearing--6006Z |
| 1 | B025 | Bearing Sleeve |
| 1 | B026 | Bearing Cover |
| 1 | B027 | Dial Holder |
| 1 | B028 | Dial |
| 1 | B029 | Bushing |
| 1 | B030 | Clutch |
| 1 | B031 | Spring |
| 1 | B032 | Ram Riser Crank |
| 1 | B033 | Snap Ring |
| 1 | B034 | Handle Grip |
Counter Balance System Parts List
__________
| QTY. | PART NO. | DESCRIPTION |
| | | |
| 1 | B100 | Counter Balance (TRM) |
| 4 | B101 | Chain Attachment Bolt/Nut |
| 2 | B102 | Chain Gear Seat |
| 4 | B103 | Chain Gear |
| 2 | B104 | Chain Gear Shaft |
| 4 | B105 | Snap Ring - S-20 |
| 1 | B107 | Counter Balance (DPM) |
| 2 | B108 | Chain Gear Seat (DPM) |
| 2 | B109 | Chain Gear (DPM) |
| 2 | B110 | Chain Gear Shaft (DPM) |
| | B111 | Snap Ring (DPM) |

252
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Other Column Parts Parts List
| QTY. | PART NO. | DESCRIPTION |
| 1 | B200 | Column Top Cover (TRM) |
| 1 | B201 | Way Cover, Top Column, Accordian |
| 1 | B202 | Way Cover, Bottom Column, Accordian |
| 2 | B203 | Ram Gib Lock Handle and Plunger |
| 2 | B204 | Ram Back Gib (TRM) |
| 1 | B205 | Ram Side Gib (TRM) |
| 6 | B206 | Ram Gib Adjustment Screw |
| set | B208 | Ram Gib Chip Guards and Gaskets |
| 1 | B209 | ProtoTRAK Pendant Arm Assembly |
| 1 | B242 | Column Top Cover (DPM) |
| 2 | B243 | Ram Back Gib (DPM)) |
| 1 | B244 | Ram Side Gib (DPM)) |
| 1 | B245 | Cable Guard (DPM) |

Other Bed Parts Parts List

| QTY. | PART NO. | DESCRIPTION |

| 1 | B230 | Vent--Left Side |
| 1 | B231 | Vent--Right Side |
| 1 | B232 | Vent--Left Front (TRM) |
| 1 | B233 | Vent--Right Front |
| 2 | B238 | Coolant Screen |
| 6 | B239 | Foot Pads |
| 6 | B240 | Footpad Bolt/Nut |
| 1 | B246 | Vent, Left Front (DPM) |

Other Table/Saddle Parts Parts List

| QTY. | PART NO. | DESCRIPTION |
| 2 | B260 | Table Gib Lock Handle & Plunger |
| 1 | B261 | Saddle Gib Lock Handle & Plunger |
| 1 | B262 | Table Gib |
| 2 | B263 | Saddle Bottom Gib |
| 1 | B264 | Saddle Side Gib |
| 2 | B265 | Table Gib Adjustment Screw |
| 6 | B266 | Saddle Gib Adjustment Screw |
| 1 | B267 (DPM) | Way Cover, Back, Bed DPM5 B267-1 |
| 1 | B268 (DPM) | Way Cover, Front, Bed DPM5 B268-1 |
| 1 | B269 | Table Stop Dog |
| 2 | B270 | Table Adjustable Stops |
| set | B271 | Saddle Gib Chip Guards & Gaskets |
| 1 | B273 (15955) | Y TRAK Sensor Bracket & Guard 16482 (guard) |
| 1 | B274 (16479) | X TRAK Sensor Bracket & Guard 16481 (guard) |
| 1 | B277 | Table Tray |
| 1 | B278 | Table Tray Rubber Pad |
| Set | B279 | Chip Guard Plates Covering Y Ball Screw |

253
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
TRAK A.G.E. Control System Parts List
| QTY. | PART NO. | DESCRIPTION |
| 1 | 20296 | Motor/Driver Assembly - Y Axis |
| 1 | 20276 | Motor/Driver Assembly - X Axis |
| 1 | 20328 | Motor/Driver Assembly - Z Axis (DPM) |
| 1 | 20252-1 | Control Cabinet Assembly (TRM) |
| 1 | 20253-2 | Control Cabinet Assembly (DPM) |
| 1 | 20180 | Pendant Assembly (TRM) |
| 1 | 20180-1 | Pendant Assembly (DPM) |
| 3 | M250C | Sensor M250C |
| 1 | 16961 | Switch Box Assembly (DPM) |
| 1 | 20065-220 | Relay Module, 220V (TRM) |
| 1 | 20065-440 | Relay Module, 440V (TRM) |
| 1 | 17009-220 | Relay Module, 220V (DPM) |
| 1 | 17009-440 | Relay Module, 440V (DPM) |

Figure 145, Electronic Hand Wheel Assembly and Parts List

NO. P/N DESCRIPTION QTY

1 20290-1 EXTERNAL CABLE BOX 1
2 21735 CABLE ASSY- ELECTRONIC HANDWHEEL 2
3 20082-1 X & Y AXIS HANDWHEEL 2
4 21583 HANDWHEEL BOX- SHEET METAL REF
5 M6 73B WASHER - LOCK BLK OX 8
6 M6-1.0x12 SCREW- SOC HD CAP, BLK OX 8

254
Southwestern Industries, Inc.
TRAK & Sport Bed Mills Safety, Installation, Maintenance, Service & Parts List Manual
Southwestern Industries, Inc

TRAK Warranty Policy

Warranty
TRAK products are warranted to the original purchaser to be free from defects in work-manship
and materials for the following periods:

Warranty Period
Product
Materials Factory Labor
New TRAK 1 Year 1 Year
Any EXCHANGE Unit 90 Days 90 Days

The warranty period starts on the date of the invoice to the original purchaser from Southwestern
Industries, Inc. (SWI) or their authorized distributor.

If a unit under warranty fails, it will be repaired or exchanged at our option for a properly
functioning unit in similar or better condition. Such repairs or exchanges will be made FOB
Factory/Los Angeles or the location of our nearest factory representative or authorized
distributor.

Disclaimers of Warranties
• This warranty is expressly in lieu of any other warranties, express or implied, including
any implied warranty of merchantability or fitness for a particular purpose, and of any
other obligations or liability on the part of SWI (or any producing entity, if different).

• Warranty repairs/exchanges do not cover incidental costs such as installation, labor,

freight, etc.

• SWI is not responsible for consequential damages from use or misuse of any of its
products.

• TRAK products are precision mechanical/electromechanical measurement systems and

must be given the reasonable care that these types of instruments require.

• Replacement of chip scrapers and wipers is the responsibility of the customer.

Consequently, the warranty does not apply if chips have been allowed to enter the
mechanism.

• Accidental damage, beyond the control of SWI, is not covered by the warranty. Thus, the
warranty does not apply if an instrument has been abused, dropped, hit, disassembled or
opened.

• Improper installation by or at the direction of the customer in such a way that the product
consequently fails, is considered to be beyond the control of the manufacturer and
outside the scope of the warranty.