Free Tutorial:
Floral Bead #3
Materials and tools:
1. Wire:
a. 18 gauge wire; 30 cm.
b. 26 gauge wire for weaving
2. Bead, size 10 mm.
3. Cutter and plier.
Bead, 10 mm
18 gauge wire
26 gauge wire
Picture 1:
Prepare 18 gauge wire with length 30 cm.
Picture Description: 30 cm
Picture 2:
Insert the wire into the bead’s hole, put the
bead right in the middle of wire.
Picture Description: 30 cm
14.5 cm 14.5 cm
10 mm bead
Picture 3:
Use 26 gauge wire and coil wire on the right
side.
Picture 4:
Continue coil the wire, make sure the coil
pattern is tight and clean.
Picture 5:
Make coiled wire with length about 6 cm.
6 cm
Picture 6:
Curve up the coiled wire.
Picture 7:
Turn the bead so the hole is showing in the front.
Picture 8:
Curve slowly coiled wire to the right direction.
Picture 9:
Slowly curve up the coiled wire and try to form
small circle.
Picture 10:
Continue curve until formed a spiral shape. Do
this step slowly and carefully.
Picture 11:
Continue curve and put coiled wire by follow
the shape of the bead.
Picture 12:
Make slight curve on the tip of coiled wire. Make
curve at length 1 cm from bead.
1 cm
Picture 13:
Curve wire to the backside until form shape like
it shown on the picture.
Picture 14:
Press the oval curved part with plier, this aims to
shift slightly it position.
Picture 15:
Now the oval part is shift slightly.
Picture 16:
Flip pendant to the backside.
Picture 17:
Use plier and curve the wire which not coiled.
Picture 18:
Curve the wire to shift its position, so it will be
easier to bind on the next step.
Picture 19:
Continue the step by coiling the wire on the
other side.
Coil the
wire
Picture 20:
Make coiled wire with length about 3 cm.
3 cm
Picture 21:
Curve down the coiled wire.
Picture 22:
Curve the wire slowly and try to form a small
circle.
Picture 23:
Continue curve coiled wire around the bead
until form and spiral shape and stop at this point.
Picture 24:
Turn the bead, now the new coiled wire is close
with the previous one.
Picture 25:
Next step, try to connect both coiled wires.
Insert string wire into the previous coiled to bind
them both.
Insert string
wire here
Picture 26:
Pull slowly string wire after inserted.
Continue coiling Picture 27:
the wire
Continue coiling wire on the above.
Picture 28:
3 cm
Add more coiled about 3 cm.
Picture 29:
Turn the bead position.
Picture 30:
Continue curve coiled wire by follow the bead
shape.
Picture 31:
Make circle curve at length 0.8 from the bead.
0.8 cm
Picture 32:
Continue curve and make circle shrink into
small size.
Picture 33:
Flip the pendant, this how looks at the frontside.
Picture 34:
Back again to the backside, use plier to curve
remaining wire on the left.
Picture 35:
Now two remaining wires become close and
make them easier to bind and weaving.
Picture 36:
Before start weaving, rotate the pendant
position.
Picture Description:
Picture 37:
Use remaining string wire to weaving. Bend
string wire on the below wire, pull it down and
insert it between both main wires.
Picture Description:
Picture 38:
Continue weaving by bind both wires one time.
Picture Description:
Picture 39:
Pull up string wire and insert it again between
two main wires.
Picture Description:
Picture 40:
Make last weaving by bind wire on the below
two times.
Picture Description:
Picture 41:
Cut the remaining string wire.
Picture 42:
Now time to continue to the next step.
Picture 43:
Bend and curve up remaining wire on the right.
Picture 44:
Put the remaining wire close with the coiled
wire.
Picture 45:
Curve the remaining wire and put it close with
the coiled wire.
Picture 46:
Continue curve the remaining wire by follow the
shape of the coiled wire and put it on same
position like it shown on the picture.
Picture 47:
Here what it looks like on the front.
Picture 48:
Repeat the step and curve up remaining wire
on the left.
Picture 49:
Curve the remaining wire and put it close with
the coiled wire.
Picture 50:
Flip the pendant into the frontside and continue
curve remaining wire close with coiled frame.
Picture 51:
Continue curve the remaining wire by follow the
shape of the coiled wire and put it on same
position like it shown on the picture.
Picture 52:
Place the end of the curve at the bottom of the
backside.
Picture 53:
This is how the backside of the pendant looks
like.
Picture 54:
Next step, connect two remaining wire by
weaving them.
Picture Description:
Picture 55:
Started weaving by bind below wire two times.
Picture Description:
Picture 56:
Bind both wires one time.
Picture Description:
Picture 57:
Pull up string wire and insert it between two
wires.
Picture Description:
Picture 58:
Pull down string wire and insert it between two
wires.
Picture Description:
Picture 59:
Bind again both wire one time.
Picture Description:
Picture 60:
Make last bind two times on the below wire.
Picture Description:
Picture 61:
Rotate the pendant to the first position.
Picture 62:
Curve slowly remaining wire
Picture 63:
Curve and make spiral form.
Picture 64:
Cut the remaining wire.
Picture 65:
Press the spiral part with plier.
Picture 66:
Here is the result.
Picture 67:
Repeat the same step and make spiral curve to
the next wire.
Picture 68:
Cut the remaining wire.
Picture 69:
Press the spiral part with plier.
Picture 70:
Here is the result.
Picture 71:
Congratulation, you just finished the Floral Bead
#3.
Thank you for download my free
tutorial.
feel free to share the link to other.
And please support me.
Copyright © Moza Vibe
