2 3/13

:: Introduction
Thank you for purchasing this Team Associated product. This manual contains instructions and tips for building and maintaining
your new RC8.2 RTR. Please take a moment to read through it an familiarize yourself with these steps as they will help you to
understand each component’s function and show you some tips for getting the most out of your RC8.2 RTR. We are continually
changing and improving our designs; therefore, actual parts may appear slightly different than the illustrations.

:: RC8.2 RS RTR Platform Features :: RC8 Platform Features

RC8.2 RS RTR Features: • 4.30:1 ratio gearboxes
• 43T diff ring and 10T pinion for increased punch and
• Powerful Reedy .21VS engine with pull start and durability over conventional buggy ratio gearboxes
Team Associated 2-chamber tuned exhaust
• Brakes
• XP 2.4Ghz radio system with digital high torque • Brake cam stops ensure brakes aren’t dragging while on
XP DS1510MG metal gear steering servo and water resistant throttle.
receiver box
• 2 piece Center diff housing split vertically for easy diff
• 16mm Big Bore 6061 aluminum shock bodies and caps with removal and maintenance
rubber shock boots
• Caster blocks adjust 14, 16, or 18 degrees with molded
• Low center of gravity 3mm thick 7075 aluminum shock inserts
towers
• Low profile elliptical 2-stage air filter
• Black hard-anodized 7075 aluminum chassis with keyed
lower suspension plates • PTFE clutch shim and easy to build design

• Updated RC8.2 racing suspension geometry • Adjustable with 0.9mm, 1.0 mm, and 1.1 mm springs
(only 1.0mm included)
• Aluminum steering knuckles for improved durability
• Fuel tank
• Choice of two factory finished RC8 bodies • Easily removeable fuel tank only 2 body clips for easy
cleaning
• Lightweight and durable drivetrain

• Upgraded Dual bell-crank steering rack for reduced

bump-steer

:: Items Included :: Additional Items Needed

Tools included with your vehicle: Your RC8.2 RS RTR kit comes ready to run.
However there are some things that are necessary to complete the kit.
• 1.5mm and 2.0mm L wrenches
• 2.5mm ball nose wrench • Transmitter batteries (6 AA) (#302, 303 recommended)
• Stamped turnbuckle wrench, 5mm & 5.5mm • Receiver batteries (4 AA) (#302, 303 recommended)
• Shock tool, upper and lower pieces (#89358) -OR-
• 10mm clutch nut wrench (#7976) • 4.8-7.4v rechargeable receiver battery pack
• 5 in 1 wrench, 17mm, 10mm, 8mm, 7mm, 5.5mm • either flat (#613) or hump (#612) style NiMh battery
• Glow igniter (#7994) (requires 1 D sized battery) • either 1600mAh LiPo (#630), 2100mAh LiPo (#631),
• Fuel bottle 400cc (#1749) • -OR- 1700 LiFe (#638) battery (recommended)
• Glow plug (#MC59) • Additional Glow plugs (#MC59) • Glow igniter battery (1 D)
• Model car fuel (20%-30% nitro recommended)
:: Other Helpful Items
• Silicone Shock Fluid / Differential Fluid (Refer to catalog for complete listings)
• Body Scissors (AE Part # 1737) • Wire cutters • Soldering Iron • FT Threadlock (#1596)
• FT Hex Wrenches (AE Part # 1541, 1655) • Starter box (#1750 recommended) • FT Turnbuckle Wrench (#89240)
• FT Nut Drivers (AE Part #1561, 1663-1668) • Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)
• Needle nose pliers • Hobby knife • Reamer/hole punch • Ride Height Gauge (#1449 recommended)
Associated Electrics, Inc. Customer Service
26021 Commercentre Dr. Tel: 949.544.7500
Lake Forest, CA 92630 Fax: 949.544.7501
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
 3
:: Table of Contents

1....................Cover 24-25.........Shocks Install

2....................Introduction 25-29.........Radio Tray Assembly

3....................Table of Contents 29-32.........Fuel Tank, Air Filter, and Engine
Assembly

4-5...............Front and Rear Diff Assembly

33................Wheel, Tires, and Body
Assembly
6-7................Center Diff Assembly

34-36.........TechTips
7-8...............Steering, Servo, and Rear
Camber Links Assembly
37-49.........Catalog
8-10.............Shocks Assembly

49................Contact Info
10.................Chassis Assembly

49-50.........Notes
10-12..........Steering Assembly

51.................Setup Sheet “Kit Setup”

12-13..........Front Geaerbox Assembly

52................1:1 Hardware “Fold Out

14-17..........Front Suspension Assembly

53................Setup Sheet “Blank”

17-19.........Rear Gearbox Assembly

54................Back Cover
19-22.........Rear Suspension Assembly

22-23.........Center Bulkhead Assembly

:: Notes
There is a 1:1 hardware foldout page in the back
?
! of the manual. To check the size of a part, line
up your hardare with the correct drawing until
This symbols indicates you find the exact size. Each part in the foldout
a special note or has a number assigned to it for ordering
instruction in the manual. replacement parts.

Associated Electrics, Inc. Customer Service

26021 Commercentre Dr. Tel: 949.544.7500
Lake Forest, CA 92630 Fax: 949.544.7501
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
4
:: Front/Rear Differential Assembly

89115
89120
Diff
Diff
housing
washer
588
#6 rease
k g
c
bla

89121 89121
Diff Diff
O-Ring 89496 O-Ring
Diff
25236 outdrive
8x16mm 16mm
se

bearing
gr 8
ea
8
ac 65
#
k
bl

:: Front/Rear Differential Assembly (cont.)

89120
89120
Sun gear
Diff
outdrive
pin

!
Align pin with
groove in sun gear

:: Front/Rear Differential Assembly (cont.)

89120
Spider
gear
assembly
 5
:: Front/Rear Differential Assembly (cont.)

89121 89120
Diff Diff 89121
O-Ring washer Diff
89496 O-Ring
Diff #6588
outdrive black grease
8 e
16mm 58 as
#6 gre
c k
bla

25236
8x16mm
bearing
89113
Diff ring
gear

:: Front/Rear Differential Assembly (cont.)

89120
89116
Diff
Diff
outdrive
gasket
pin
#6588
black grease

!
Thin Gasket

:: Front/Rear Differential Assembly (cont.)

89120
Sun gear
!
Tighten screws
89208 x4
3x14mm
fhcs
evenly and firmly.
!
Build
front and

!
Diff fluid
rear diffs!

!
5,000cst
#5453

Align pin with

groove in sun gear Fill with diff fluid to
top of gears.
6
:: Center Differential Assembly

89115
Diff 89120
housing Diff
washer
#6588
black grease
89121
89121 Diff
Diff O-Ring
O-Ring

25236
8x16mm
se
gr 8
ea
8

bearing
ac 65

89496
#
k

Diff
bl

outdrive
16mm

:: Center Differential Assembly (cont.)

89120
Sun gear
89120
Diff
89120
outdrive
Spider
pin
gear
assembly

!
Align pin with
groove in sun gear

:: Center Differential Assembly (cont.)

89496
89121
Diff
Diff
outdrive
O-Ring
16mm
#6588
black grease

25236
8x16mm
bearing

89110
Spur gear
(46T)
 7
:: Center Differential Assembly (cont.)

89120
89120
Diff
Sun gear
washer
89120
89121 Diff
Diff outdrive
O-Ring pin

!
Align pin with
groove in sun gear

:: Center Differential Assembly (cont.)

89208 x4

89116
Diff gasket
!
Tighten screws
3x14mm
fhcs

evenly and firmly.

#6588
black grease Diff fluid
5,000cst

!
#5453

Fill with diff fluid to

top of gears.

:: Steering Turnbuckle Assembly

89075 x2
Steering
ballstud
89074 x2 89268
Steering 42mm steel
eyelet turnbuckle

17.8mm !
Build right
and left
sides!
8
:: Servo Link Assembly

89078 x2 89267
Straight 32mm steel
eyelet turnbuckle

7.5mm 89078 x2
balljoint

:: Rear Camber Link Assembly

89076 x2
Camber
pivot balls

89076 x2 89269
Camber 38mm steel
rod end turnbuckle
89076 x2
Camber
ball joints
7.7mm

!
Build right
and left
sides!

:: Shock Assembly
89066 x2
Shock
O-rings
89580
89352 16x29mm
Spacer RTR shock
body (front)

89358 89582
Lower 16x38mm
shock tool
!
Use the lower shock tool Sho
RTR shock
body (rear)
c
to load the two o-rings flui k
d
and spacer for easy
lubing and installation
into the shock body
 9
:: Shock Assembly - (cont.)
89215
Locknut
(piston)

89353
Shock piston
set (1.3, blank)

89260
89278 x2
Shock shaft,
2.5mm
29mm, (front)
piston
89352 washer
O-Ring
89261 89358
89352 Shock shaft, Upper
Bottom 38mm (rear) shock
nut tool

:: Shock Assembly - (cont.)

!
ck
Sho d
flui

Short boots for Fill to top with

front shocks. shock fluid:
! Long boots for Front: 40wt
rear shocks. #5423
Sho
c Rear 30 wt
flui k
d
89556 #5422
RC8.2
shock boot

!
One drop of
(front shown)
89065
Shock rod
89065
Shock
rod end
shock end ball
fluid on
threads.

:: Shock Assembly - (cont.)

Bladder Installation 89335
Shock
cap

89351
Shock
bladder

A B C
As you install the shock cap with the bladder, it will force
out any extra fluid. If you install the cap with the shaft
!
Some residual shock
89396
fully extended, you are running FULL REBOUND. Shock
fluid may appear from
your first few runs collar
To run less rebound, unthread the cap 1-2 turns and
compress the shaft to the desired position and around the shock cap
re-tighten the cap with the shaft compressed. as a result of bleeding.
Start with no rebound.
10
:: Shock Assembly - (cont.)

89396 Front shock: 7mm

Shock Rear shock: 2mm
pre-load 1mm
89396
89293 x2 clips
Shock 2mm
Front spring, pre-load
silver (3.9lbs) clips 3mm
(short spring)
89348 x2
Rear spring,
5mm

10mm
!
silver (3.3lbs) 89354 Build two
(long spring) 16mm front and
shock two rear
spring cup shocks!

:: Chassis Assembly

89552 x2
Side guards
(left & right)

25201 x4
89476 3x8mm
RC8B fhcs
+3mm
chassis

:: Steering Assembly
89010 89011 25202
Top plate 89455 Top plate 3x10mm
(lower) 3x22mm (upper) fhcs
fhcs
25203 x4
89010 3x12mm
89258 Top plate fhcs
Front (upper)
chassis
brace 25202
hinge pin
bushing 3x10mm
89039 x2 fhcs
Hinge pin
25215
bushing
M3
(3 dot down) 25215 x4
locknut
M3
3 dot down locknut
 11
:: Steering Assembly (cont.)

31404 x2 89016
6x10mm Servo
bearing saver 89117 x2
bolt Diff
shim
89015
Servo
saver
!
gap setting:
89016
Servo
arm 2mm saver
# spring
#65 thr 1596
ea
bla
ck
88
gre
89015 dl
ock
89016
ase
Servo Servo
saver saver
bellcrank retainer

:: Steering Assembly (cont.)

25204 x2
89272 3x16mm
Steering fhcs
rack

89014 x2
31404 x2 Steering
6x10mm rack post
bearing
89218 x2
Washer
89015
3x8mm
Steering
89161 x4 bellcrank
25215 x2
5x8mm M3
bearing locknut

:: Steering Assembly (cont.)

25215 x2
M3
locknut

Smooth edge towards

drivers side!
89013 x2
Steering

! posts
12
:: Steering Assembly (cont.) / Front Gearbox Assembly
#1596
thread lock 89114
89214 x2 Diff pinion
#1596
4x12mm thread lock gear
fhcs 25215 x4
M3 locknut

25236 x2
8x16mm
bearing
89017
Inner
gearbox

:: Front Gearbox Assembly - (cont.)

89278 x2
89036

!
2.5mm
Arm
washer
mount
Key setscrew onto (B)
flat side of shaft.
Tighten with no
89221 endplay.
5x4mm
#15
setscrew 89201 x2
thr 9
ead 6
lock
96
#15 lock 2.5x3mm
e a d
89571 thr
bhcs
SC8.2e
center drive
line input 89224 x2
cup 3x16mm 89218 x2
shcs 3x8mm
washer

:: Front Gearbox Assembly - (cont.)

89226
3x26mm
shcs

25215
M3 locknut
 13
:: Front Gearbox Assembly - (cont.)
96
89225 x2 #15 lock
r e ad 89549
th
3x24mm Front
shcs upper arm 89269
38mm
89473 x2 96
#15 lock
ad
steel
Steel thr
e
turnbuckle
shock
standoffs 89076
Camber
rod ends
89218 x2
3x8mm

!
washer 7.5mm
Smooth edge towards
89586 drivers side!
Front
shock tower
Build right
(front) and left
sides!

:: Front Gearbox Assembly - (cont.)

89040 x2
Inner
hinge pin

89202 x4 hinge pin

bushing
3x12mm
bhcs

89039 x2
Hinge pin
bushing
1 dot
(1 dot)

:: Front Gearbox Assembly - (cont.)

!
Diff shims
89472 installed to diff,
Front diff installed to
bulkhead ! gearbox.
spacer

89224 x2
3x16mm
shcs
89117 x2
89017 Diff
Outer ! shim
gearbox
14
:: Front Suspension Assembly

89102 89105
CVA CVA pin
bone

#6588
black gre
ase
8
#658 e
greas
black

89105
CVA 89573
!
u-joint
coupler
Lightweight
cv axle, steel
!
Axle has additional holes
for crosspin to extend
!
the life of the Axle. Build Two!

:: Front Suspension Assembly - (cont.)

!
Build right
and left
sides!

ck
ad 96
lo
89162 Left Side

th #15
re
15x21x4mm
bearing
89096
89028 Wheel hex
25236 89251
Steering block pins 89221
8x16x5mm Wheel hex
(left, right) 5x4mm
bearing
setscrew

:: Front Suspension Assembly - (cont.)

#1596
thread lock
#1596
thread lock
89558
Caster
blocks
(left, right)

Note:
One drop only.
#1596 Spread evenly
thread lock inside the threads.
 15
:: Front Suspension Assembly - (cont.)
89029 Note: direction
Steering ! blue
block
89206
16 deg

bushing
4x10mm
(short)
16 deg

bhcs red

89032
89029 16 deg. caster
Steering block angle bushing
bushing (long) (red)

! 89207
4x12mm 89032
!
16 deg. caster Build right
Do not tighten until bhcs Note:
Key bushings into angle bushing and left
bushing is keyed
into steering block. ! steering block. (blue) sides!

:: Front Suspension Assembly - (cont.)

89091
Swaybar !
!
89220
joint 4x12mm

!
setscrew
Build right
89511 x2 and left
Droop
Swaybar sides!
eyelet
screw
25192
placement! 3x20mm
4671 shcs
3x10mm
setscrew 89550
RC8.2
! front arms

! 89511
Swaybar
ball joint
(left,
right)
Build Two!

:: Front Suspension Assembly - (cont.)

89040 x2
Inner
hinge pin

!
89041
Outer
hinge pin
Build right
31520 and left
2.5x6mm sides!
bhcs
16
:: Front Suspension Assembly - (cont.)
hinge pin 89039 x2
Build right bushing Hinge pin

! and left
sides!
bushings
(two dot,
down)

2 dot 89035
down
Arm
mount
(A)

89228 x2 89218 x2
25215 x2 3x40mm 3x8mm
M3 shcs washer
locknut

:: Front Suspension Assembly - (cont.)

Side
View

89031 x4
Blue 1.7mm
caster spacer

25215 x2

89225 x2
M3
locknut !
Build right
3x24mm
shcs
and left
sides!

:: Front Suspension Assembly - (cont.)

25225 x2
#
3x3mm thr 1596
ead
loc
setscrew k

89088
2.5mm
anti roll
bar (silver)
89226
! 3x26mm
89219 x2 shcs

!
3x5mm
setscrew
Tighten screws to 25215
89017 remove free play but
31531 x2 M3
Swaybar ensure some
3x6mm locknut
mount movement in the
bhcs anti-roll bar.
 17
:: Front Suspension Assembly - (cont.)

25215
M3
locknut

89022
Front
bumper

89217 x2
4x14mm
fhcs

#15
thr 9
ead 6 25204
89214 x4 lock
3x16mm
4x12mm fhcs
fhcs

:: Rear Gearbox Assembly

89017 89114

!
Inner Diff pinion
gearbox gear
Key setscrew onto
25215 x2
flat side of shaft.
M3 locknut Tighten with no
endplay.
ck
ad 96
lo
th #15

89221
re

5x4mm
setscrew
25236 x2
8x16mm
bearing 89571
SC8.2e
center drive
line input
cup
18
:: Rear Gearbox Assembly - (cont.)
89039 x2 hinge pin
Hinge pin bushing 89211
bushing 3x26mm
(2 dot down) fhcs

89258
89037 Chassis
2 dot brace
Arm down
mount (C) (rear)

89218 x2 25215
89224 x2
3x8mm M3
3x16mm
washer locknut
shcs

:: Rear Gearbox Assembly - (cont.)

89225 x2 89011
3x24mm Body
89473 x2 shcs mount
Steel shock and
standoff spacer
25215 x2
M3
thr
#15
9
ead 6
locknut
lock

89218 x2
3x8mm
washer
89587 89218 x2
25192 x2 Rear shock 25192 x2
3x8mm
3x20mm tower (rear) 3x20mm
washer
shcs shcs

:: Rear Gearbox Assembly - (cont.)

89454 x2
3x12mm
shcs
 19
:: Rear Gearbox Assembly - (cont.)

!
Diff shims in-
stalled to diff,
89472 diff installed to
gearbox.
Front
bulkhead
!
spacer

89224 x2 !
3x16mm 89117 x2
shcs 89017 Diff
Outer shim
gearbox

:: Rear Suspension Assembly

89162
15x21mm
bearing 89096
89033
Wheel hex
hub
pins
carrier
89572 (left, right)
SC8.2e
dogbone

ck
ad 96
lo
th #15
axle

re
! 89107
Bearing 25236
Build right 8x16mm
shield 89251 89221
and left bearing Wheel hex 5x4mm
sides! setscrew

:: Rear Suspension Assembly - (cont.)

89091 89220
Swaybar 4x12mm
joint setscrew
!
89511 x2
!
Swaybar
eyelet

!
25192
4671 3x20mm
3x10mm shcs
Droop
!
setscrew
screw
placement!
!
89551
89511 Build right
RC8.2
Swaybar and left rear arm
Build Two! ball joint sides!
20
:: Rear Suspension Assembly - (cont.)

!
Build right
and left
sides! 89031 x2
Hub
spacers
(red)

89575 x2
SC8.2e
31520 dogbone
2.5x6mm 89041 (82mm)
bhcs Outer
hinge pin

:: Rear Suspension Assembly - (cont.)

89278 x2
2.5mm
washer

89201 x2 89038
2.5x3mm Arm
bhcs mount (D)

89218 x2
3x8mm
washer

89228 x2 89040 x2
#
thr 1596 Inner
3x40mm ead
loc
shcs k hinge pins

:: Rear Suspension Assembly - (cont.)

25225 x2
89089 3x3mm
25215 2.8mm setscrew
#1596
M3 anti roll thread
lock
locknut bar (gold)

#1596
thread
lock

89017
Swaybar

89474
mount
!
3x22mm ! Tighten screws to
remove free play but
shcs 31531 x2 89219 x2 ensure some
3x6mm 3x5mm movement in the
bhcs setscrew anti-roll bar.
 21
:: Rear Suspension Assembly - (cont.)
89202 x2
3x12mm
bhcs

89218 x2
3x8mm
washer
89592
RC8.2e
RTR wing
(black)

89540 25192 x2
RC8.2 3x20mm
wing mount shcs
upper brace

25215 x2
M3
locknut

89540 x2
RC8.2
wing mounts

25215 x2
M3
locknut

:: Rear Suspension Assembly - (cont.)

25215
M3
89228
locknut
3x40mm
shcs
22
:: Rear Suspension Assembly - (cont.)

25215
M3
locknut

89217 x2
4x14mm
fhcs

89214 x2
4x12mm
fhcs
25204
3x16mm
fhcs

:: Center Bulkhead Assembly

89019
Center
bulkhead
89122 x2
(top)
Brake
pads

brake pad
gap: 4.5mm

89122 x2
! 89250 x2
Fiber
brake rotor
Brake bolt Build Two!
 23
:: Center Bulkhead Assembly (cont.)

! !
! 89226 x4
Do not tighten
#89226 3x26mm
! 3x26mm
shcs completely until ! shcs
the next step!
89254
Center
diff top
plate

89124 x2
Brake
cam

89019 x2
Center
bulkhead
(bottom)

:: Center Bulkhead Assembly - (cont.)

!
Install dog bones
!
Tighten all screws !
!
!
into center diff after bottom screws !
outdrives! have been installed!

25220 x4
5mm
washer
89584
96mm
dogbone
(front) 89583
89214 x4
99mm
4x12mm
dogbone
fhcs
(rear)
24
:: Shocks Install
89083
Shock

!
Note the direction
bushing

of the shock cap

when installing onto
shock standoffs

!
25612
M3 locknut
with flange
Install
two front
shocks.

:: Shocks Install - (cont.)

89454
3x12mm
shcs

!
After installation, adjust droop
91069 screw to get a front shock length of
103mm measured center to center
Shock mount
on the shock cap / shock mount pin.
pin, steel

:: Shocks Install - (cont.)

89083
Shock

!
bushing

Note the direction

of the shock cap
when installing onto

!
shock standoffs

Install
two rear
shocks. 25612
M3 locknut
with flange
 25
:: Shocks Install - (cont.)

89454

!
3x12mm
shcs
After installation, adjust droop
screw to get a rear shock length of
91069 122mm measured center to center
Shock mount on the shock cap / shock mount pin.
pin, steel

:: Radio Tray Assembly

6338
89253 Antenna
89003
Antenna tube and cap
Receiver
89004 mount box top
89222 x2
Receiver 2.5x8mm
89003 box foam shcs
Wire pad
insert (bottom)
89003
Switch
mount

Receiver
89004
Receiver
89003 box foam
Receiver pad (top)
box

:: Radio Tray Assembly - (cont.)

5 cell inline pack configuration 21173 x2
shown. For hump pack or LiPo
packs, use optional forward
Small
battery box #89471. body clip 25203 x2
3x12mm
fhcs
5 cell inline pack

AA receiver 89253
pack Radio tray
Receiver

(4 AA batteries
not included)
26
:: Radio Tray Assembly - (cont.)
89218 x8 25187 x8 31531 x3
Washers 3x14mm 3x6mm
3x8mm bhcs bhcs
Transponder
Throttle Steering and 3x6mm
servo servo bhcs not
not inlcluded!
!
89006 x4 !
Servo
spacers
!
Servo mounts vary per
servo manufacturer.
Space your servos low
to the chassis without
touching the bottom.

:: Radio Tray Assembly - (cont.)

A - Airtronics 25215
F - Futaba M3
H - Hitec locknut
J - JR
Printed here
!
!
25201
89007 3x8mm
Steering fhcs
Enlarge holes
in servo horn! servo horn
89008
89078 x2
Servo cone
Servo link
washer
rod end 2308
3x18mm
bhcs
89008
89267 Servo horn
32mm steel ring
turnbuckle

89078 x2
ball
joint

!
Steering turnbuckle was
built on page 8!

7.5mm
 27
:: Radio Tray Assembly - (cont.)
89008
Servo cone 25215 x2
M3 25225 x2 89126 x2
washer Set
locknut 3x3mm
Printed here 89126 setscrew collar
A - Airtronics Brake bias 89126
F - Futaba block Throttle
H - Hitec pivot
J - JR
!
!
89218 89202
3x8mm 3x12mm
washer bhcs When adjusting
! linkage, it may
89126 x2
Brake link

!
89008 be necessary to
89008 change hole loca-
Throttle 89203 Servo tion for correct
servo horn 3x16mm horn ring alignment with
Enlarge holes
carburetor
in servo horn! bhcs

:: Radio Tray Assembly - (cont.)

#15
thr 9
ead 6 25225
lock
89126 3x3mm
Throttle 89126 setscrew
spring Set collar

25225
3x3mm
89126 setscrew
Throttle
link
89126
! Set collar 89126
Throttle
ball cup

:: Radio Tray Assembly - (cont.)

#1596
thread lock

25201 96 25225 x2
#15
3x8mm th r e a d loc
k
3x3mm
fhcs setscrew

89318 x2
Brake
lever
28
:: Radio Tray Assembly (cont.)

25203 x6
3x12mm
fhcs 89205
3x26mm
bhcs

!
There will be an unused screw hole
25215
M3
at the bottom of the receiver box.
This will not be used for the RC8.2 locknut

:: Radio Tray Assembly (cont.)

0.5mm
89126 x2
Brake
washer

89126 x2
brake
spring
!
After installation,
(silicone) leave a 0.5mm
gap between the
25225 x2 two brake levers!
3x3mm
setscrew
89126 x2
Set
collar
 29
:: Radio Tray Assembly (cont.)
:: Brake bias adjusters
:: 6
1mm
gap :: Rear :: Front

:: 2 :: 5 :: 9

:: 1
:: 3
:: 4
::1 - Turn on transmitter and buggy. Adjust servo ::5 - Pull cams to engage brakes. Set collar ::7 - Set throttle EPA to max. Apply full throttle on
horn until position is parallel with centerline at (with brakes engaged) to have 1mm gap transmitter and set EPA so that the carb is full
neutral. between tubing and collar. open. Be careful not to over-extend the carb.

::2 - Set pre-load on spring so that throttle will Remember: transmitter is still on during this ::8 - Set max brake EPA at 30% as a starting point.
close. step.
::9 - Brake bias adjusters: thread the adjuster into the
::3 - Set 0.5mm gap on throttle collar. ::6 - Trim off excess brake link wire. mount to achieve stronger brakes on that end of
the buggy.
::4 - Trim off excess rod.

:: Fuel Tank Install

89131
Fuel tank

21173 x2
76mm Small
cut body clip

7725 x2
Fuel
tubing

89128 x2
Fuel tank
mount

25203 x2
3x12mm
fhcs
30
:: Air Filter Install
Pullstart
oi filt
l # er 89142 engine

!
77
10
Air filter
outer
25201 x2
When oiling element
the filter
3x8mm
elements, 89141 fhcs
place both Air filter
inside a
plastic bag
inner !
and squeeze element
to help
evenly coat
the filter.
89139
r 0
lte 1
Air filter !
!
fi 77
oi
l # cap 89140
Air filter 3719
89139 6” wire tie
hose Use #3719
Air filter wire tie
base here!

:: Engine Install
Clutch shimming
instructions: 89218
If assembly does 3x8mm
not spin freely, washer
RACERS TIP: use #89218
trim clutch shim. (small clutch shim
included in kit) on
89138 screw to increase
Flywheel end play.
collet
If crankcase 89132
89135 extends past 16T
Clutch nut clutch bearing, clutchbell
89136 use#89218
89133 x3 Flywheel (large clutch shim
included in kit) to 25237 x2
1.0mm
89137 reduce end play. 5x10mm
clutch
springs 89265 x3 Clutch ! 89223
89148 x4 bearing
shim Use upper shock Clutchbell
RTR fiber tool to install 3x8mm
! clutch shoe clutch springs. shcs
shim

:: Engine Install (cont.)

89147 89274
89224 x4
Header RTR
3x16mm
#1596 gasket header
shcs thread lock

89231 x4
3mm
lock 3719 x2
washer 6” wire
tie

7733
Exhaust
tubing
89257 x2 89273 coupler
Engine RTR
mount tuned
pipe
 31
:: Engine Install (cont.)
25226
4x5mm
setscrew

#1596
thread lock

89130 x2
Engine
mount
89144 plates
Pipe
mount
th #15
re
ad 96 #1596
lo thread lock
ck

89145
25201 Pipe
3x8mm wire 89213 x6
fhcs 4x6mm
fhcs

:: Engine Install (cont.)

25226
4x5mm
set screw
#1596
thread lock

89207 x4 #1596
thread lock
4x12mm
fhcs
32
:: Engine Install (cont.)

Pressure line
from fuel tank lid to
exhaust pipe nipple

Fuel line
from fuel tank to
carburetor

:: Engine Install (cont.)

89325 x2
Fuel line
clips

!
!

!
Adjust angle of carb

! Install fuel line clips!

ball joint to align with
throttle servo.
 33
:: Wheels, Tires, and Body Install

97
#15
lue
ire g
CA t

Tires:
When gluing tires to wheels, use a
!
fast-curing Tire glue (CA) Build four
89255 x4 (AE Pt#1597). This is available at
wheels/
RTR Pre-glued your local hobby shop. Make sure
wheel/tire
to clean the mounting surface of the tires
tire with alchohol for best adhesion.

:: Wheels, Tires, and Body Install (cont.)

89498 or 89499 2208 x2
RC8.2 RTR Body Large
(# 89498 Gray) hood
(#89499) White) pins

31531
3x6mm
bhcs

89252 x4
Wheel hex
nuts
(silver)
34
:: Building Tips
Tires:
The tires need to be glued to the wheels using any fast-curing FT Tire glue (CA) (AE Pt#1597). This is available at your
local hobby shop. Make sure to clean the mounting surface of the tire with alchohol for best adhesion.

Receiver Pack:
Your RC8.2 does not come with a receiver pack. It is recommended that you use a 5-cell 1600mah pack (minimum) in
either stick (AE Pt #612) or hump (AE Pt#613) pack configuration (your RC8.2 will accepteither). Charge your pack per
the battery manufacturer’s instructions. This will need to be done before you can setup up your RC8.2.

Engine Tuning:
Follow the manufacturers instructions to correctly tune your engine. You will need to adjust the fuel mixture according to
altitude, weather, etc.

:: Chassis Tips
Gearing:
Recommended gearing: 16:44. This is a good starting point for most tracks. Follow your engine manufacturer’s
recommendations for gearing options. Typically on larger, more open track layouts a 17T clutch bell is used.

Gear Mesh:
To correctly set your gear mesh, follow the steps below:
1. Loosen the engine mount screws so you can slide your engine from side to side freely.
2. Slide the engine until the clutch bell comes in contact with the spur gear. Tighten the engine mount screws.
Now “rock” the spur gear. There should be a little “free play” between the gears.
3. If you have a small amount of ‘free-play’, continue building your RC8.2. If not, go back to Step 1. Be sure to check for
“free-play” through a full rotation of the spur gear.

WARNING! Caution when setting / checking gear mesh after running your vehicle, the clutch bell WILL BE HOT!

Differential Fluid:
Team Associated includes a complete bottle of 5,000cst diff oil. You can also provide your own oil and try one of the
optional setups.
Standard differential fluid setup: Front = 5,000cst; Center = 5,000cst; Rear = 5,000cst.
Optional diff setup 1 (high grip track): Front = 5,000cst; Center = 10,000cst; Rear = 5,000cst.

Center Differential:
Use the standard setup for most cases. Some racers will try thicker oil (7,000-10,000cst) when greater acceleration
is needed. This is typically done on very smooth tracks since thicker fluid can reduce handling in bumpy conditions.

:: Front End Tips

Front Differential:
Use the standard setup for most cases. Try 7,000cst to 10,000cst to get less low speed steering and better
acceleration out of turns.

Kickup Bushing:
Generally more kick-up will provide better handling in the bumps and have better straight line acceleration.
Less kick-up will provide more all around steering and have a more aggressive feel.

Caster:
The standard caster block insert setup is for 16 degrees. The standard inboard kick-up is 9 degrees (2-dot up insert
in A-plate). You can reduce the caster using 14 degree inserts (also move both upper cone washers in front of the ball
joint) for smoother steering. Changing to 18 degree inserts (also move both upper cone washers behind the ball joint)
will typically provide more steering on power but reduce handling in bumpy conditions.

Front Upper Pivot Insert:

The standard setup is to use 2-dot up in the tower and 1-dot in the top plate. It is recommended to maintain a 1 dot
gap (1mm per dot) front to rear when using 2-dot up in the A-Plate. Reducing the A-Plate insert to 1-dot allows the use
of same dot number insert in both tower and top plate. Going up to 3-dot up in the tower will give more turn in, but less
steering on power/exit. Going down (1-dot, 2-dot down) will reduce turn in, but give more steering on exit.
 35
:: Front End Tips (cont.)
Front Camber Link-Outer:
The standard short location will work the best for most tracks. Going to the long front link will give you more steering,
but can make the car less predictable in bumps and exiting turns.
Front Camber Angle:
A good starting camber setting is –2 degrees. Positive camber, where the top of the tire is leaning out, is typically not
recommended.

Front Toe-In:
Zero degree toe-in (tires pointing straight forward) is a good starting setting. You can increase turn in by adding 1-2
degrees of toe-out (front of tires point slightly out). Front toe - in is not a typical tuning adjustment used by the Team.

Front Ride Height:

The front ride height setting you should use most often is with 29mm of gap between the chassis bottom and the
ground. Check the ride height with the FT Ride Height Gauge (#1449) by lifting up the entire vehicle about 8-12 inches
off the bench and drop it. After the suspension “settles” into place, then raise or lower the ride height with the shock
clips as necessary and recheck.

Front Arm Shock Location:

Inside on the arm will give a more responsive front end. Outside on the arm will be less responsive steering, but will be
more predictable through bumps.

:: Rear End Tips

Rear Differential:
Start with the standard setup. For expert drivers, the most popular setting is 3,000 cst. The thicker 5,000cst kit
oil will rotate less in the turns and accelerate straight on power. The thinner oil (2,000 or 3,000cst) will give more low
speed traction.

Anti-squat:
Anti-squat denotes the angel of the rear inner hinge pin relative to the ground. This setting is adjusted by changing the
insert bushing in the C-Plate. The kit setting is 2 degrees (2-dot down) but you change to 1 degree (3-dot down). Typically
less anti-squat lets the suspension work more over the bumps, but it will sacrifice the ability to square up on power.

Rear Camber Link Length & Vertical Adjustment:

You can change the length of the camber link on the hub or tower as well as adjust the vertical location on the tower.
A longer link will give the feeling of the most grip, but it will not be as responsive to square up on throttle, and might get
loose if driven hard. This can easily be corrected by running the shorter link on the hub, but it will sacrifice some forward
grip.

Changing to a higher location on the tower will be a smaller adjustment than changing the length of the upper link.
Going up on the tower location has a similar effect as a longer camber link, but not as drastic. For example, if you change
to the short rear link on the hub and you need to gain more forward grip, try raising the link up on the tower. New
additional lower holes should be used when running the optional hinge pin hole in the rear hub carrier.

Rear Hub Hinge Pin Height:

The upper hole gives more rear grip on turn in, and good forward traction, but it might have difficulty squaring up out of
turns. The lower hinge pin hole in the hub will be more responsive on throttle, and give more side grip in the turns.

Rear Hub Spacing:

You have 3 options for rear hub spacing, FWD, MIDDLE, & BACK. The kit setting provides a good balance of rear
traction and steering, and will be used most often. Moving the hubs FWD will give more rear traction for low grip tracks.
You can use the hubs BACK on high grip tracks for more on-power steering. Also, you can replace the included shims to
get intermediate settings.

Rear Camber:
A good starting camber setting is –2 degrees. Use the included #1719 camber gauge to set your camber. Adding a
small amount of positive camber, where the top of the tire is leaning out, will tend to improve straight-line acceleration on
loose tracks.

Rear Ride Height:

The rear ride height setting you should use most often is 29mm of gap between the chassis bottom and ground.
Check the ride height with the FT Ride Height Gauge (#1449) by lifting up the entire vehicle about 8-12 inches off the
bench and drop it. After the suspension “settles” into place, then raise or lower the ride height with the shock clips as
necessary and recheck.

Rear Arm Shock Location:

Inside on the arm will give less entry steering, accelerates better straightline through bumps, but may lack side bite.
Outside on the arm will be less grip, more steering, but will be more predictable when it breaks traction.
36
:: Droop Settings (Buggy shown but applicable for all vehicles)
Note: Rear hub spacing is not recommended with RTR dog bones.
For more adjustability, use CVA’s in place of dog bones.

Step 1: With only the bottom of the shocks attatched, the droop screws raised all the way, and the chassis above
your working surface so the arms are at full extension, you should be able to easily slide the top of your shock over the
standoff screw, while leaving the shock at full extension. If the mounting hole of the shock cap is above or below the
standoff screw, adjust the droop screw accordingly. Repeat for all corners of your vehicle. Measure from the center of
the standoff screw to the center of the shock riser button to get your FULL DROOP setting.The front shocks should be
102mm, while the rear shocks should be 120mm.

Step 2: Finish installing the shock to the standoff. Step 3: Measure from the center of the shock
Set your vehicle to your desired droop setting. standoff screw to the center of the shock riser button
To increase your droop turn the droop screw (from the to get your final droop setting. The front shocks should
top) counter-clockwise (loosen), turn the droop screw both be set at the same lenght, as should the rear
(from the top) clockwise (tighten) to decrease your shocks. * The normal droop setting is between 0-5mm
droop. Remember, never back the screw out beyond from the FULL DROOP measurement.
full droop or you could risk damage to your vehicle.
Front Droop: Increasing front droop (loosen droop screws) will increase off-throttle steering. It also allows the
front end to lift more, giving more rear grip and less front grip on-power. Remember to never loosen the screws beyond
the FULL DROOP setting. Decreasing front droop (tighten droop screws) yields more on-power steering and quicker
response at the expense of some stability in bumpy sections. It will also give less off-throttle steering.
Rear Droop: Increasing rear droop (loosen droop screws) will increase traction in bumpy sections, but will reduce
high-speed stability. Remember to never loosen the screws beyond the FULL DROOP setting. Decreasing rear droop
(tighten droop screws) will increase stability in high speed sections, but will reduce stability in bumpy sections.
Setup Sheets:
Most often the best way to get your car handling right is to go to our website www.rc10.com and click on the
“Setup Sheets” link, then the link to your vehicle, then search for your vehicle. Our team of professional drivers help
develop these setups at National events. Also, most drivers have a “base” setup that they use as a starting point for ev-
ery event. Try running some of our base setups OR look for track conditions and tires that are similar to your local track
and mimic that setup. Remember, each adjustment has a purpose, so copy everything from the setup sheet and then
make adjustments based on the recommendations in here at http://www.rc10.com/rc/tuning.
 37
:: Shocks :: Front and Rear Gear Differential
25612 M3 Locknut With Flange 20 25236 8x16x5 Bearings 2
89065 Shock Rod End 4 89113 Diff Ring Gear, Includes Diff Gasket 1
89066 Shock O-Rings 8 89115 Diff Housing 1
89067 Shock Limiters, Set 1 89116 Diff Gasket 4
89083 Shock Bushings 4 89117 Diff Shims 8
89215 Piston Locknut 10 89120 Diff Sun/Planet Gears, Includes 1
89260 29mm RTR Shock Shaft, Front 2 Washers and Pins, Set
89261 38mm RTR Shock Shaft, Rear 2 89121 Diff 0-Rings, Big and Small, Set 1
89278 2.5mm Washer 20 89208 3x14mm FHCS 10
89335 16mm Shock Caps 2 89496 Diff Outdrive, 16mm 2
89351 16mm Shock Bladders 8
89352 16mm Shock Rebuild Kit 1
89353 16mm Shock Pistons 8
89354 16mm Shock Spring Cups 4 89208
89396 16mm RTR Pre-load Clips, Shock Collar Set 1
89556 RC8.2 Shock Boot Set 1 89208
89580 16x29mm Shock Body RTR, Blue 2 89120
89582 16x38mm Shock Body RTR, Blue 2 89496
89120
89121
25236
89121
89113
89115
89116
25236 89121
89083
89121

89353 25612 89496 89120

89335
89215
89351

Front :: Center Gear Differential

89580 25236 8x16x5 Bearings 2
89278 89109 Spur Gear 44T, Includes Diff Gasket - metal 1
89110 Spur Gear 46T, Includes Diff Gasket - metal - Kit 1
89396 Rear
89115 Diff Housing 1
89353 89582 89116 Diff Gasket 4
89396 89120 Diff Sun/Planet Gears, Includes 1
Front Washers and Pins, Set
89260 89352 89066 89121 Diff 0-Rings, Big and Small, Set 1
89208 3x14mm FHCS 10
Front 89372 Spur Gear 50T, Includes Diff Gasket - metal 1
Rear 89293 89352 89373 Spur Gear 52T, Includes Diff Gasket - metal 1
89261 89374 Spur Gear 54T, Includes Diff Gasket - metal 1
Rear 89352 89496 Diff Outdrive, 16mm 2
89348
Front
and 89208
Rear
89065 89556 89208
89354 89120 89496
89120
89065
89121
89121 25236

89115
:: Springs 89110
89292 16x29mm front spring black (3.3lbs) Pr.
89293 16x29mm front spring silver (3.9lbs) - Kit Pr.
89294 16x29mm front spring bronze (4.7lbs) Pr. 25236 89116
89295 16x29mm front spring complete set 1 89121 89121
89347 16x38mm rear spring black (2.7 lbs) Pr.
89348 16x38mm rear spring silver (3.3 lbs) - Kit Pr.
89349 16x38mm rear spring bronze (4.0 lbs) Pr. 89496
89350 16x38mm rear spring complete set 1 89120
38
:: Shock Fluid :: Top Plate
5420 10 Weight Silicone Shock Fluid 2oz. 2208 Large Hood Pins 6
5421 20 Weight Silicone Shock Fluid 2oz. 25202 3x10mm FHCS 20
5422 30 Weight Silicone Shock Fluid 2oz. 25203 3x12mm FHCS 20
5423 40 Weight Silicone Shock Fluid 2oz. 25215 M3 Locknut 20
5424 22.5 Weight Silicone Shock Fluid 2oz. 89010 Top Plate - Kit 1
5425 80 Weight Silicone Shock Fluid 2oz. 89011 Body Mount Set 1
5426 27.5 Weight Silicone Shock Fluid 2oz. 89039 Hinge Pin Bushings, 1/2/3 dot, Set 1
5427 15 Weight Silicone Shock Fluid 2oz. 89214 4x12mm FHCS 10
5428 25 Weight Silicone Shock Fluid 2oz. 89226 3x26mm SHCS 10
5429 35 Weight Silicone Shock Fluid 2oz. 89234 Blue Aluminum Top Plate (FT) 1
5430 45 Weight Silicone Shock Fluid 2oz. 89236 Black Aluminum Top Plate (FT) 1
5431 55 Weight Silicone Shock Fluid 2oz. 89455 3x22mm FHCS 10
5432 32.5 Weight Silicone Shock Fluid 2oz.
5433 37.5 Weight Silicone Shock Fluid 2oz.
5434 42.5 Weight Silicone Shock Fluid 2oz.
5435 50 Weight Silicone Shock Fluid 2oz. 2208
5436 60 Weight Silicone Shock Fluid 2oz.
5437 70 Weight Silicone Shock Fluid 2oz. 89011
5438 47.5 Weight Silicone Shock Fluid 2oz.

89214
25202 89214 89455
:: Steering
25204 3x16mm FHCS 20
25203 89010
25215 M3 Locknut 20
31404 6x10mm Bearing 2
89226
89013 Steering Posts 2
89014 Steering Rack Post 2 25203
89015 Servo Saver (plastic), Set 1
89016 Servo Saver Bolt, Nut, Spring, Set 1 89039 25215
89075 Steering Ballstuds 4
89117 Diff Shims 8 89010
89161 Steering Bearing Set 1
89214 4x12mm FHCS 10 89039 25215
25202 25215
89218 3x8mm Washer 10
89272 RTR Steering Rack 1

:: Lubes & Adhesives / Decals / Misc.

1105 FT Green Slime Shock Lube 1
31404 25204 1596 FT Locking Adhesive 1
1597 FT Tire Adhesive, Medium 1
25215 5450 Silicone Diff Fluid 1000cst 1
25204
89016 5451 Silicone Diff Fluid 2000cst 1
89272 5452 Silicone Diff Fluid 3000cst 1
89014 5453 Silicone Diff Fluid 5000cst 1
25215 5454 Silicone Diff Fluid 7000cst 1
89161 5455 Silicone Diff Fluid 10000cst 1
5456 Silicone Diff Fluid 20000cst 1
89015 89075 5457 Silicone Diff Fluid 30000cst 1
5458 Silicone Diff Fluid 60000cst 1
5459 Silicone Diff Fluid 100000cst 1
89161 89075 6588 Black Grease - 4cc 1
89218 6591 S.Diff Lube - 4cc 1
25215 6636 Silicone Grease - 4cc 1
89015 89014 6727 Servo Tape 2
31404
89161 716 Reedy 2009 Sticker Set 1
717 Reedy Powered Logo Decal 1
89117 3816 American Bumper Sticker 1
89016 89015 3820 AE Logo Decal Sheet 1
3834 AE Blue Embossed Logo Sticker 2
89117 89161
89218 31404
89016
25215
31404
89013

89013

89214
89214
 39
:: Front Gearbox
25215 M3 Locknut 20 89201 89224
89218
25236 8x16x5 Bearing 2 89278
31531 3x6mm BHCS 10
89017 FR/RR Gearbox 1 89036
89035 Arm Mount A 1 89039 89040 89218
89036 Arm Mount B 1
89039 Hinge Pin Bushings, Set 1
89040 Inner Hinge Pin, Set 1
89035 89201
89114 Diff Pinion Gear 1
89201 2.5x3mm BHCS 10 89218 89040 89278
89214 4x12mm FHCS 10
89217 4x14mm FHCS 10 89039
89218 3x8mm Washer 10 89584
89219 3x5mm Setscrew 10 89218 89221
89221 5x4mm Setscrew 10 89228
89224 3x16mm SHCS 10
25215
89226 3x26mm SHCS 10
89228 3x40mm SHCS 10 89571
89278 2.5mm Washer 20 89017
89472 RC8B Front Bulkhead Spacer 2 25236
89571 SC8.2e Center Drive Line Input 2 89472
89584 Dogbone 96mm 1
89226 25215
89224
89017 25236
89214
89219 89114

89017 25215
31531
89219
89217

:: Front Suspension
25192 3x20mm SHCS 20
25215 M3 Locknut 20
25236 8x16x5 Bearing 2 89549 89040
31520 2.5x6mm BHCS 6 89105
89028 Steering Blocks Pr.
89029 Steering Block Bushings, Set 1 89269
89031 Caster/Hub Spacers, Set 1 89206
89032 Caster Angle Bushings, Set 1 89102 89076
89040 RC8 Inner Hinge Pins, Set 1 89029
89041 RC8 Outer Hinge Pins, Set 1
89074 Steering Rod Ends 4 25215
89573 89031
89075 RC8 Steering Ballstuds 4
89076 RC8 Camber Rod Ends, Set 1
89096 RC8 Wheel Hex Pins 4 89225
89028
89102 RC8 Front/Rear CVA Bone 2 89558 89032 89075
89105 RC8 CVA Rebuild FR/RR, Set 1
89162 15x21x4 Bearing 2 25236
89206 4x10mm BHCS 10 89032
89207 4x12mm BHCS 10 89029 89162 89096
89220 4x12mm Setscrew 10
89221 5x4mm Setscrew 10 89220 89207
89225 3x24mm SHCS 10 89454
89251 Wheel Hex Drive Pr.
89252 Wheel Hex Nut, silver 2
25215
89251
89268 Steel Turnbuckle, 42mm 2 25192
89269 Steel Turnbuckle, 38mm 2 89252
89454 3x12mm SHCS 10 89075
89549 RC8.2 Front Upper Arms Pr. 89550 89221
89550 RC8.2 Front Arms Pr.
89558 RC8.2 Caster Blocks Pr. 91069
89573 SC8.2e Light Weight CV 2 89074 89268
Axle, Steel
91069 Shock Mount Pin, Steel 4 89074
31520 89041
40
:: Rear Gearbox
25215 M3 Locknut 20 89219
25236 8x16x5 Bearing 2
31531
31531 3x6mm BHCS 6
89017 RC8 FR/RR Gearbox, Set 1 89224
89037 Arm Mount C 1
89038 Arm Mount D 1
89039 RC8 Hinge Pin Bushings, Set 1 89472
89040 Inner Hinge Pin, Set 1
31531
89017
89114 RC8 Diff Pinion Gear 1
89201 2.5x3mm BHCS 10 89114
89211 M3x26mm FHCS 10 89211 89017
89214 4x12mm FHCS 10
89217 4x14mm FHCS 10
89218 3x8mm Washer 10 25236
89219 3x5mm Setscrew 10 25215
89221 5x4mm Setscrew 10 25215 89217
89224 3x16mm SHCS 10
89278 2.5mm Washer 20 89221
89279 3x45mm SHCS 10
89472 RC8B Front Bulkhead Spacer 2 89201 89279
89571 SC8.2e Center Drive Line Input Cup 2 25236 89278 89218
89583 Dogbone 99mm 1
89571
89214 89218
89040 89201
89278
89583 89039
89038
89218 89040

89039
89224 89037

:: Rear Suspension
25192 3x20mm SHCS 20
25215 M3 Locknut 20 89076
25236 8x16x5 Bearings 2
31520 2.5x6mm BHCS 6
89031 RC8 Caster/Hub Spacers, Set 1 89076
89033 RC8 Hub Carriers Pr.
89041 RC8 Outer Hinge Pins, Set 1 89269
89076 RC8 Camber Rod Ends, Set 1 89575 89076
89096 RC8 Wheel Hex Pins 4
89076
89107 RC8 Rear CVA Shield/Boot, Set 1
89162 15x21x4 Bearing 2
89220 4x12mm Setscrew 10
89221 5x4mm SHCS 10 89572 89474
89251 Wheel Hex Drive Pr.
89252 Wheel Hex Nut, silver 2 89107
89269 38mm Steel Turnbuckle 2 89031
89454 3x12mm SHCS 10 89162
89474 3x22mm SHCS 10
89551 RC8.2 Rear Arms Pr. 25215 89096
89572 SC8.2e Dog Bone Axle 2
89575 SC8.2e RTR Dogbone 82mm 2
89033 89251
91069 Shock Mount Pin, Steel 4
25236 89252
89220 89454
91069 89221
31520

89041
25192
89551
 41
:: Front Shock Tower :: Rear Shock Tower
89039 Hinge Pin Bushings, 1/2/3dot Set 1 25192 3x20mm SHCS 20
89202 3x12mm BHCS 10 25215 M3 Locknut 20
89218 3x8mm Washer 10 89011 Body Mount Set 1
89225 3x24mm SHCS 10 89218 3x8mm Washer 10
89473 RC8B Steel Shock Stand-offs 4 89225 3x24mm SHCS 10
89586 Front Shock Tower 1 89454 3x12mm SHCS 10
89473 RC8 Steel Shock Standoffs 4
89587 Rear Shock Tower 1

89225
89225
89218
89218 89225
89225 89587 89011
89586
89473 89473
25215
89218 89218

25215
25192
89039
89202 89473
89218
89202
89454
89473
25192
89218
25192

:: Center Bulkhead :: Chassis Braces

25220 Washer, 5 x 12 x 1 25 25204 M3x16mm FHCS 20
25225 3x3mm Setscrew 20 25215 M3 Locknut 20
89019 RC8 Center Bulkhead, Set 1 89068 RC8 Pivot Chassis Brace Set (Front) 1
89122 RC8 Brake Pads, Set 1 89069 RC8 Pivot Chassis Brace Set (Rear) 1
89123 Heatsink Brake Discs - Kit 2 89077 Chassis Brace Rod Ends, Set 1
89124 RC8 Brake Cams/Levers, Set 1 works with #89068, 89069
89214 4x12mm FHCS 10 89238 FT Aluminum Chassis Brace (Front) 1
89226 3x26mm SHCS 10 89239 FT Aluminum Chassis Brace (Rear) 1
89250 Fiber Brake Rotors 2 89258 RC8 Chassis Braces, Plastic - Kit 1
89254 Center Top Plate 1 (Front, Rear)
89226
89226 89226

89226
89124 89124
89254 89258
25225 89122 Rear
89122
89124
25215
89124 89122
89123
89122 Front
89122 25215
89019
89122 89019 89258
89122 25204
89019 25204
25220
89123 25220
25220
25220
42
:: Radio Tray
6338 Antenna Tube and Cap 1
21173 18T Body Clips 12 21173
25187 3x14mm BHCS 20
25203 3x12mm FHCS 20
31531 3x6mm BHCS 6 21173
89003 RC8 Receiver/Battery Box, Set 1
89004 RC8 Receiver Box Pads, Set 1 6338
89005 Aluminum Antenna Mount, Set 1 89003
89006 RC8 Servo Mount Spacers, Set 1
89209 3x18mm FHCS 10 25187
89214 4x12mm FHCS 10 89004 89253
89218 3x8mm Washer 10 25187 89222
89222 2.5x8mm SHCS 10 89218
89253 Antenna Mount, Set 1 89218 89006
89454 3x12mm SHCS 10
89471 RC8.1 Forward Battery Box and 1 89006 89004 89003
Radio Tray (Optional)
89454 89003
25187 31531

89454 25203
89214
89471
Optional 89471 89003
89471 25203
25203
25203
89471
25203

89471 25203
25203

:: Linkage
2308 3x18mm BHCS 6
25225
25201 3x8mm FHCS 20
25215 M3 Locknut 20
25225 3x3mm Setscrew 20
89007 Steering Servo Horns, Set 1 89126 89126
89008 Throttle Servo Horns, Set 1
89078 RC8 Servo Link Rod Ends, Set 1
89126 RC8 Linkage Set 1 25215
89202 3x12mm BHCS 10 89126
89203 3x16mm BHCS 10
89205 3x26mm BHCS 10
89126 25225
89218 3x8mm Washer 10 89126
89267 32mm Steel Turnbuckle 2
25201 89126
25215
89007

89007 25225
89126
89078
89007 89126
89078 89126 89126
25215
89267 25201
89205 89126 25225
2308 89008
89218 89126
89078
89008 89202 89126 89126
89078
89203 89008
25215
 43
:: Chassis
25201 3x8mm FHCS 20
25226 4x5mm Setscrew 20
89018 RC8 Gearbox Gasket 4 89552
89022 RC8 Front Bumper 1
89130 RC8 Engine Mount Plates 2
89144 RC8 Pipe Mount 1
89145 RC8 Pipe Mount Wire 1
89207 4x12mm BHCS 10
89213 4x6mm FHCS 10
25201
89224 3x16mm SHCS 10
89231 3mm Lock Washer 10
89257 RC8 Engine Mount 2
89476 RC8B +3mm Chassis 1 89476
89552 RC8.2 Side Guards Pr. 25201
89231
89224
89224

89552
89231
89257 89231

89130 89257
25226 25201
89130
89207 89022 89144
89207 89145
25201
89207 25201

89213 89213

:: Anti-Swaybars :: Wing
4671 3x10mm Setscrew 6 25192 3x20mm SHCS 20
25225 3x3mm Setscrew 20 25204 3x16mm FHCS 20
89086 FT Antiroll Bar Set 1 25215 M3 Locknut, (Black) 20
89087 FT Antiroll Bar Black, 2.2mm 1 89202 3x12mm BHCS 10
89088 FT Antiroll Bar Silver, 2.5mm - Kit (rear) 1 89218 3x8mm Washer 10
89089 FT Antiroll Bar Gold, 2.8mm - Kit (front) 1 89228 3x40mm SHCS 10
89091 FT Antiroll Bar Socket Joint 4 89540 RC8.2 Wing Mount, Set 1
89093 FT Antiroll Bar Black, 3.0mm 1 89592 RC8.2e RTR Wing, (Black) 1
89511 RC8.2e RTR Swaybar Link Set 1
89202 89218
89202
89218
25225

89511 89091
89592

4671 89540

25215 25192
89511 89511
89087 89540
89088 25215
89089 89228
89093
25215 89540
25215
25215
44
:: Wheels / Tires :: Body / Decals
89152 RC8 Wheels (White) 4 2208 Large Hood Pins 6
89153 RC8 Wheels (Yellow) 4 31531 3x6mm BHCS 6
89255 RTR Pre-Glued Wheel/Tire (White) Pr. 89150 RC8 Body w/Window Mask (Clear) 1
89296 RC8 83mm Wheels (White) - Kit 4 89275 RC8 RTR Body (Black) 1
89297 RC8 83mm Wheels (Yellow) 4 89276 RC8 RTR Body (White) 1
89277 RC8 RTR Body Wrap Decals 1
89497 RC8.2 RTR Decal Sheet 1
89498 RC8.2 RTR Body (Gray) 1
89499 RC8.2 RTR Body (White) 1
89523 RC8e Body w/Window Masks (Clear) 1
89559 RC8.2 Decal Sheet 1

2208

89150

89255
2208

31531

:: Fuel Tank :: Air Filter

21173 18T Body Clips 12 3719 6” Nylon Wire Ties 2
25203 3x12mm FHCS 20 7710 Pre-Filter Fluid 1
89066 Shock O-Rings 8 25201 3x8mm FHCS 20
89128 Fuel Tank Mount, Set 1 89139 RC8 Air Filter Set 1
89131 RC8 Fuel Tank 1 89140 RC8 Air Filter Hose 1
89325 Fuel Line Clips, Set 1 89141 Air Filter Elements 1
89142 Air Filter Outer Elements 4

89325

25201
89325
21173 25201

21173 89142
89131

89139 89141
89066
89066
89066
89066 89128

89128
25203
89140

25203
 45
:: Clutch :: Exhaust
25237 5x10x4 Bearings 2 2357 Rear Exhaust Manifold Spring 6
89127 Clutch Bell, 17T 1 7733 Exhaust Tubing Coupler 1
89132 Clutch Bell, 16T - Kit 1 25094 Header Spring 1
89133 Clutch Springs 1.0 - Kit 3 89147 Header Gasket 1
89134 Clutch Shoes (aluminum) w/ Shims, Set 1 89175 Black Non-Stick Muffler 1
89135 Clutch Nut 1 89176 Black Non-Stick Header 1
89136 Flywheel (Hard Anodized) 1 89177 Polished Muffler 1
89137 Clutch Shims 4 89178 Polished Header 1
89138 Flywheel Collet 1 89181 Muffler to Header Springs 3
89148 Clutch Bell Shim Set 1 89273 RTR Tuned Pipe 1
89157 0.9 Clutch Springs 3 89274 RTR Header 1
89158 1.1 Clutch Springs 3
89159 Short Clutch Nut 1
89218 3x8mm Washer 10
89223 3x8mm SHCS 10
89265 Fiber Clutch Shoes - Kit 3
89375 Clutch Bell, 14T 1 89175
89376 Clutch Bell, 13T 1

89138
89265 89135
89132 89176
89148 89148
89136
89223
89137
25237 25237 89133
89218

2357

:: Fueling :: Starting Equipment

1748 Nitro Fuel Bottle 600cc 1 1738 FT Glow Starter 2
1749 Nitro Fuel Bottle 350cc 1 1750 FT Starter Box 1
7724 Fuel Line 15” 1 7994 D-Size Glow Ignitor 20
7725 Fuel Line 3’ 1 1
25076 Fuel Primer Bulb 1

7724 1748
7725 1749
1750

25076
46
:: Factory Team and Option Parts :: Factory Team and Option Parts - (cont.)
25392 3mm Blue Locknut, Flanged 10 89536 RC8.2 Swaybar Pivot Ball w/setscrews 4
31550 M3 Aluminum Lock Nut 6 89537 RC8.2 Swaybar Drop Link w/pivots 4
80930 1/8 Scale Electric Conversion Kit 1 89541 FT RC8.2 Front Spring Kit 1
89005 Aluminum Antenna Mount 1 89542 FT RC8.2 Front Spring, 4.00 Green 2
89012 RC8 Steering Rack, Carbon Fiber 1 89543 FT RC8.2 Front Spring, 4.30 Silver 2
89016 Servo Saver Bolt, Nut, Spring (Blue) 1 89544 FT RC8.2 Front Spring, 4.65 Blue 2
89020 Center Bulkhead Plate CF 1 89545 FT RC8.2 Rear Spring Kit 1
89045 RC8 FT 0.5 Degree Toe Bushing 1 89546 FT RC8.2 Rear Spring, 3.25 Green 2
89053 Gold Shock Shaft 29mm 2 89547 FT RC8.2 Rear Spring, 3.55 Silver 2
89054 Gold Shock Shaft 38mm 2 89548 FT RC8.2 Rear Spring, 3.75 Blue 2
89070 RC8 Ti Turnbuckle Set 1 89553 RC8.2 Front Hinge Pin, TiN 2
89071 Camber Turnbuckles 5mm 2 89554 HD Shock Shaft, 4x26mm Pr.
89073 Servo Turnbuckle 4mm 1 89555 HD Shock Shaft, 4x36mm Pr.
89082 RC8 Shock Standoffs, Aluminum 4 89556 RC8.2 Shock Boots, Front & Rear 1
89094 Nyloc Wheel Hex Nuts, Blue 2 89557 Pin Reatainer O-Ring and Boot 2
89095 Wheel Hex, Aluminum 2 89558 RC8.2 Caster Blocks, Left & Right Pr.
89123 RC8 Heatsink Brake Disc 2 89561 RC8.2 Mud Guards, Left & Right Pr.
89136 RC8 Flywheel, Hard 1 89563 FT Woven Carbon-fiber Shock Tower, front 1
89146 RC8/T Clutch Shoes, Hard 3 89564 FT Woven Carbon-fiber Shock Tower, rear 1
89160 Drivetrain Bearing, Set 1 89565 Vertical Caster Block, 16° (use #89566, 89567) Pr.
89161 Steering Bearing Set 1 89566 Vertical Steering Blocks (use #89565, 89567) 2
89229 Blue Countersunk Washer 10 89567 Bushings and Pins (use #89565, 89566) 4ea
89234 Blue Aluminum Top Plate (FT) 1 89568 Optional Gear Set 1
89235 RC8 CNC Aluminum Steering Rack 1 91069 Shock Mount Pin, Steel 4
89236 Black Aluminum Top Plate (FT) 1
89237 RC8 Skid Plate 1
89284 RC8 Rear Stub Axle (Aluminum) 2
89285 RC8 Front Stub Axle (Aluminum) 2
89286 RC8 Gearbox Input Cup (Aluminum) 2
89290 FT 16x29mm Front Shock Kit 1
:: XP Electronics
89291 FT 16x29mm Front Shock Bodies, Hard Coated & Pr. 29133 XP DS1903 Servo 1
Threaded - requires #89555 shock shafts 29134 XP DS1903MG Servo 1
89344 FT 16x38mm Rear Shock Bodies, Hard Coated & Pr. 29150 TX/RX Charger, charges transmitter and receiver 1
Threaded - requires #89555 shock shafts 29166 XP DS1313 Digital Servo 1
89346 FT 16x38mm Rear Shock Kit 1 29167 XP DS1015 Digital Servo 1
89355 16mm Shock Collar, threaded 2 29168 XP DS1510MG Digital Servo 1
89380 RC8 FT Machined Steering Blocks Pr. 29209 Gear Set, DS1313 1
89381 RC8 FT Machined Rear Hubs Pr. 29210 Gear Set, DS1015 1
89405 Nyloc Wheel Nuts (Silver) 4 29211 Servo Case , DS1313/DS1015 1
89406 Nyloc Wheel Nuts (Black) 4 29212 Accessory Pack, DS1313/DS1015 1
89456 16mm Piston 10x1.1 4 29214 TRS403-SSi 2.4GHz 3Ch Receiver 1
89460 RC8 Aluminum A-Plate 1 29215 XP2G 2.4GHz Radio System 1
89461 RC8 Aluminum B-Plate w/Pins, Set 1 29216 XP3G 2.4GHz Radio System 1
89462 RC8 Aluminum C-Plate 1 29217 TRS402-SSi 2.4GHz 2Ch Receiver 1
89463 RC8 Aluminum D-Plate w/Pins, Set 1
89464 RC8B Aluminum Front Shock Tower 1
89465 RC8B Aluminum Rear Shock Tower 1 :: LRP Engines, Chargers, Soldering Irons
89466 RC8B Inner Hinge Pins, 4mm HMA, Set 1 LRP32111 ZR.21X Spec.2 Non Pull Race Engine 1
89467 HD Shock Shaft, 4x29mm 1 LRP32120 LRP ZZ.21c Ceramic Competition Engine 1
89468 HD Shock Shaft, 4x38mm 1 LRP32802 LRP Z.28R Spec. 3 Engine 1
89469 HD Shock Ends, Set 1 LRP32810 ZR.30 Spec.2 Pullstart 1
89470 RC8B Shock Tower Hinge Pin Bushings, Set 1 LRP32815 ZR.30 X Competition, non-pullstart 1
89473 Steel Shock Standoff 2 LRP32820 ZR.32 Spec.2 Pull Start Engine 1
89476 FT RC8B +3mm Chassis 1 LRP41281 Quadra Pro 2 Charger 1
89477 FT RC8B Light Outdrive, Front 2 LRP41555 Pulsar Touch Competition Charger 1
89478 FT RC8B Light Outdrive, Rear 2 LRP42103 LiPo Balance Board XH 1
89481 FT RC8B Low B-Plate 1 LRP42104 LiPo Balance Board FP/TP 1
89482 FT RC8B Low B-Plate Inserts 2 LRP42105 LiPo Balance Board PQ 1
89485 FT RC8B Aluminum Steering Posts 2 LRP42305 Pulsar Touch Temperature Sensor 1
89487 RC8.2 FT Rear Swaybar, 2.5 Green 1 LRP43200 LRP Competition 20A Power Supply 1
89488 RC8.2 FT Rear Swaybar, 2.6 White 1 LRP45200 LiPo Parallel Balancer 1
89489 RC8.2 FT Rear Swaybar, 2.7 Blue 1 LRP65800 High Power Solder Station 1
89490 RC8.2 FT Rear Swaybar, 2.8 Yellow 1 LRP65802 Soldering Tip 5mm 1
89492 16mm Piston 5x1.1 + 5x1.2 4 LRP65803 Soldering Tip 1.2mm 1
89494 RC8B Light Diff Ring Gear, Includes Diff Gasket 1 LRP65804 Soldering Handle 1
89495 RC8 FT Light Spur Gear, 44T 1
89496 Diff Outdrive 2
89529 RC8.2e FT Motor Mount Set 1 :: LRP 1/8 Brushless Systems
89530 RC8.2 FT Front Swaybar Kit 1 LRP53225 Dynamic 8 Brushless Motor 1600KV 1
89531 RC8.2 FT Rear Swaybar Kit 1 LRP53235 Dynamic 8 Brushless Motor 2000KV 1
89532 RC8.2 FT Front Swaybar, 2.2 Green 1 LRP53240 Dynamic 8 Brushless Motor 2200KV 1
89533 RC8.2 FT Front Swaybar, 2.3 White 1 LRP80786 IX8/Dynamic 8 2200KV 1
89534 RC8.2 FT Front Swaybar, 2.4 Blue 1 LRP80788 IX8/Dynamic 8 2000KV 1
89535 RC8.2 FT Front Swaybar, 2.5 Yellow 1 LRP80880 IX8 Brushless ESC 1
 47
:: Reedy Nitro Engines and Parts :: Reedy Batteries
800 Reedy 121VR .21 Off-Road Comp. Nitro Engine 1 302 AA Alkaline 1.5V (4) 1
801 Reedy 121VR-ST .21 Comp. Nitro Engine 1 303 AA 2700mAh NiMH 1.2V Rechargeable 1
802 Reedy .21 VS Pull Start Nitro Engine 1 304 Pro RX Battery 1600mAh 7.4V Flat 1
28000 121 VR Crankshaft 1 305 Pro RX Battery 1300mAh 6.6V Flat 1
28001 121 Crankcase 1 604 526-S AC/DC 2S-6S LiPo/LiFe Charger 1
28002 121 Connecting Rod 1 606 Charge Harness 2S Saddle Pack 4mm 1
28003 121 Wrist Pin 1 607 Charge Harness 2S Standard Pack 4mm 1
28004 121 Circlips 1 610 447-S AC/DC NiMH Peak Charger 1
28005 121 VR Cylinder & Piston 1 612 1600 Series 6.0V Hump Receiver Pack 1
28006 121 VR Heatsink Head 1 613 1600 Series 6.0V Flat Receiver Pack 1
28007 121 VR Button 1 626 Reedy LiPo 5500mAh 14.8V 60C 1
28008 121 Carb Insulator 1 630 Pro RX LiPoBattery 1600mAh 7.4V 1
28009 121 Head Shim Set 1 631 RX LiPo Battery 2100mAh 7.4V 1
28010 121 Backplate 1 632 TX Lightweight Battery 1350mAh 11.1V 1
28011 121 Exhaust Gasket 1 633 TX Battery - 3PK, M11 3000mAh 11.1V 1
28012 121 Ball Bearing (Rear) 1 634 TX Battery - Helios, Z1 2400mAh 11.1V 1
28013 121 Ball Bearing (Front) 1 635 Starter Box Battery 2200mAh 1
28014 121 Screw Set 1 636 6.0V Voltage Regulator 1
28015 121 VR Complete Carburetor 1 637 TX Battery - M11X 2500mAh 7.4V 1
28016 121 VR Carb Body Set 1 638 RX LiFe Battery 1700mAh 6.6V 1
28017 121 Needle Valve Assembly 1 693 Wolfpack 2400mAh 7.2V w/TAM connector 1
28018 121 Needle Valve 1 694 Wolfpack 3000mAh 7.2V w/TAM connector 1
28019 121 Carb Slide Assembly 1 695 Wolfpack 3600mAh 7.2V w/TAM connector 1
28020 121 Idle Screw 1 700 Wolfpack 4200mAh 7.2V w/TAM connector 1
28021 121 VR O-Ring Set 1 722 LiPo 18.5V 3800mAh 5S 40C 1
28022 121 Exhaust Spring Set 1 733 Wolfpack LiPo 3700mAh 14.8V 35C w/DEANS® 1
28023 121 Dust Cap Set 1
28024 121 Flywheel Collet 1
28025 121 Restrictor (7.0mm) 1 :: Qualifier Series Vehicles
28026 121 Restrictor (8.0mm) 1
7052 Pro Lite 4x4 RTR, 1/10 Scale (ready-to-run) 1
28027 121 Restrictor (9.0mm) 1
20510 RIVAL Electric Monster Truck RTR, 1/8 Scale 1
28028 121 Restrictor (6.5mm) 1
(ready-to-run)
28029 121 Restrictor (7.5mm) 1
30112 APEX Touring V-Type, 1/10 Scale (ready-to-run) 1
28030 121 Restrictor (8.5mm) 1
28031 121 VR-ST Crankshaft (ADLC) 1
28032 121 VR-ST Crankcase 1
28033 121 Wrist Pin (ADLC) 1 :: 1/18 Kits and RTR’s
28034 121 VR-ST Cylinder and Piston 1 20103 RC18B2 - RC18T2 Team Kit 1
28035 121 VR-ST Heatsink Head 1 20121 SC18 RTR Brushless (ready-to-run) 1
28036 Ceramic Rear Bearing for 121 Engine 1
28037 121 VR-ST Complete Carburetor 1
28038 121 VR-ST Carburetor Body Set 1
28039 121 VR-ST Midrange Screw 1
28040 Reedy RT3 Turbo Plug, Very Hot 1 :: 1/12, 1/10 Kits and RTR’s
28041 Reedy RT4 Turbo Plug, Hot 1 2042 Nitro TC3 RTR Plus (ready-to-run) 1
28042 121 Restrictor (5.0mm) 1 4020 FT 12R5.2 Kit 1
28043 121 Restrictor (5.5mm) 1 7025 RC10T4.2 FT Kit 1
28044 121 Restrictor (6.0mm) 1 7029 SC10 Associated/RC10.com Truck RTR (ready-to-run) 1
28045 Reedy 2035 Tuned Exhaust System 1 7030 SC10 KMC Wheels Race Truck RTR (ready-to-run) 1
28046 Reedy 2035 Muffler 1 7037 RC10T4.1 RTR 2.4GHz Brushless (ready-to-run) 1
28047 Reedy Exhaust Manifold 1 7038 SC10.2 FT Kit 1
28048 Reedy 2039 Tuned Exhaust System 1 7046 SC10 RS RTR, Lucas Oil (ready-to-run) 1
28049 Reedy 2039 Muffler 1 7047 SC10 RS RTR, Monster Energy (ready-to-run) 1
28050 Reedy Turbo Glow Plug Caddy 1 7048 SC10 RS RTR, Pro Comp (ready-to-run) 1
7049 SC10 RS RTR, Rockstar/Makita (ready-to-run) 1
7050 SC10 RS RTR, Hart and Huntington (ready-to-run) 1
7092 GT2 RS Truck Nitro RTR (ready-to-run) 1
7093 SC10GT RTR (ready-to-run) 1
8020 FT RC10R5 Kit 1
8022 FT RC10R5.1 Kit 1
:: Reedy Motors 9039 RC10B4.1 RTR 2.4GHz Brushless (ready-to-run) 1
9040 FT RC10B4.1 Worlds Kit 1
929 1515-SL Brushless Motor 2000kV 1
9041 FT RC10B4.2 Kit 1
988 Sonic 1512 1800kV Competition Brushless Motor 1
9050 SC10B RS RTR (ready-to-run) 1
989 Sonic 1512 2100kV Competition Brushless Motor 1
9062 FT B44.2 4WD Buggy Kit 1
30101 TC4 Club Racer 4WD Touring Car Race Roller 1
30108 FT TC6.1 WC 4WD Touring Car Kit 1
90004 SC10 4x4 Kit 1
90005 SC10 4x4 Lucas Oil RTR (ready-to-run) 1
90006 SC10 4x4 Pro Comp RTR (ready-to-run) 1
90007 SC10 4x4 Rockstar/Makita RTR (ready-to-run) 1
90010 SC10 4x4 FT Kit 1
48
:: 1/8 Kits and RTR’s :: Tools
20501 MGT 4.60 SE RTR (ready-to-run) 1 1449 Offroad Ride Height Gauge 1
20502 MGT 8.0 Nitro RTR (ready-to-run) 1 1541 FT Hex Driver Set, (7 pcs) 1
20503 Limited Edition MGT 4.60 Nitro RTR, w/flag body 1 1542 FT .050” Silver Hex Driver 1
(ready-to-run) 1543 FT 1/16” Black Hex Driver 1
20504 Limited Edition MGT 8.0 Nitro RTR, w/flag body 1 1544 FT 1.5mm Purple Hex Driver 1
(ready-to-run) 1545 FT 5/64” Blue Hex Driver 1
80905 RC8RS “Race Spec” Nitro Buggy RTR (ready-to-run) 1 1546 FT 3/32” Gold Hex Driver 1
80906 RC8.2 Nitro Buggy FT Kit 1 1547 FT 2.5mm Green Hex Driver 1
80907 RC8.2e Electric Buggy FT Kit 1 1548 FT 3mm Red Hex Driver 1
80908 RC8.2e Electric Buggy RTR (ready-to-run) 1 1551 FT Screwdriver Set 1
80909 RC8.2 Nitro Buggy RTR (ready-to-run) 1 1553 FT Phillips Silver Screwdriver 1
80912 RC8T Championship Edition 1 1554 FT Silver Spring Hook Tool 1
80933 SC8.2e Short Course Race Truck, Rockstar/Makita 1 1561 FT Nut Driver Set, (6 pcs) 1
Electric RTR (ready-to-run) 1562 FT 3/16” Black Nut Driver 1
80934 SC8.2e Short Course Race Truck, Slick Mist Electric 1 1563 FT 1/4” Red Nut Driver 1
RTR (ready-to-run) 1564 FT 5.5mm Red Nut Driver 1
1565 FT 11/32” Green Nut Driver 1
1567 FT 8mm Gold Nut Driver 1
1589 FT 5/64” Blue Ball Hex Driver 1
1590 FT 3/32” Gold Ball Hex Driver 1
1592 FT Ball Hex Driver Set, (3 pcs) 1
1655 FT 8-Piece 1/4” Hex Drive Set 1
1656 FT 1/4” Hex Drive Handle, without tips 1
:: Apparel 1657 FT 1/4” Hex Drive .050” Tip 1
SP35** Reedy 09’ White T-Shirt (L, XL, 2XL) 1 1658 FT 1/4” Hex Drive 1/16” Tip 1
SP36** Reedy 09’ Black T-Shirt (M, L, XL, 2XL, 3XL) 1 1659 FT 1/4” Hex Drive 5/64” - 2.0mm Tip 1
SP37** Reedy 2012 T-shirt - Black (S, M, L, XL, 2XL, 3XL) 1 1660 FT 1/4” Hex Drive 3/32” Tip 1
SP38 Reedy Trucker Hat 1 1661 FT 1/4” Hex Drive 1.5mm Tip 1
SP39 Reedy Patch 1 1662 FT 1/4” Hex Drive 2.5mm Tip 1
SP66** Stencil Blue T-Shirt (S, M, L, XL, 2-6XL) 1 1663 FT 1/4” Hex Drive 3/16” Nut Driver Tip 1
SP67** AE Stencil Gray Sweatshirt (S, M, L, XL, 2XL, 3XL) 1 1664 FT 1/4” Hex Drive 1/4” Nut Driver Tip 1
SP68** AE Stencil Blue T-Shirt (M, L, XL) 1 1665 FT 1/4” Hex Drive 11/32” Nut Driver Tip 1
SP69** AE 26 Time World Championship T-Shirt, Black 1 1666 FT 1/4” Hex Drive 5.5mm Nut Driver Tip 1
(S, M, L, XL, 2XL, 3XL) 1667 FT 1/4” Hex Drive 7.0mm Nut Driver Tip 1
SP70** Associated Windbreaker (S, M, L, XL, 3XL) 1 1668 FT 1/4” Hex Drive 8.0mm Nut Driver Tip 1
SP71** Associated Winter Jacket (S, M, L, XL, 2XL) 1 1669 FT 1/4” Hex Drive 5/64” - 2.0mm Ball End Tip 1
SP73** AE Long Sleeve T-Shirt (S, M, L, XL, 2XL) 1 1670 FT 1/4” Hex Drive 3/32” Ball End Tip 1
SP74** AE White T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL) 1 1671 FT 1/4” Hex Drive Standard Screwdriver Tip 1
SP75** AE Blue T-Shirt (S, M, L, XL, 2-6XL) 1 1672 FT 1/4” Hex Drive Phillips Screwdriver Tip 1
SP76** AE Black T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL) 1 1673 FT 1/4” Hex Drive 2.5mm Ball End Tip 1
SP77** AE 2012 T-Shirt, Blue (S, M, L, XL, 2XL, 3XL) 1 1674 FT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm, 1
SP78** AE 2012 T-Shirt, White (S, M, L, XL, 2XL, 3XL) 1 1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)
SP79** AE 2012 T-Shirt, Black (S, M, L, XL, 2XL, 3XL) 1 1719 FT Camber + Track Width Tool 1
SP84** Reedy 3D T-Shirt, Black (S, M, L, XL, 2XL, 3XL) 1 1737 FT Body Scissors 1
SP85** Reedy 3D Zip Hoodie, Black (S, M, L, XL, 2XL, 3XL) 1 3718 12 Inch Nylon Wire Ties 12
SP86** Reedy Girl’s 3D T-Shirt, Black (S, M, L, XL) 1 3719 6 Inch Nylon Wire Ties 12
SP102 Outer & Inner Boxes, for #SP-416 1 3720 8 Inch Nylon Wire Ties 12
SP103 Inner Boxes only, for #SP416 1 3987 FT Droop Gauge 1
SP411S AE Hat 11’ Flat Bill Black S/M 1 7709 4 Inch Nylon Wire Ties 12
SP411L AE Hat 11’ Flat Bill Black L/XL 1 89240 FT RC8 Turnbuckle Wrench 1
SP413S 26 Time World Championship Hat S/M 1 89358 16mm Big Bore Shock Tools 1
SP413L 26 Time World Championship Hat L/XL 1 91107 13mm Shock Tools 1
SP416 Associated Car Carrier Bag, Medium 1
SP417 1/10 FT Motor Bag 1
SP418 Factory Team 1/10 Car Carrier Bag 1
SP420** AE Pit Gloves (M, L, XL) Pr.
SP421S AE 2012 Hat, Black, Flat Bill, S/M 1
SP421L AE 2012 Hat, Black, Flat Bill, L/XL 1
SP422S AE 2012 Hat, Black, Curved Bill, S/M 1
SP422L AE 2012 Hat, Black, Curved Bill, L/XL 1
SP423S AE 2012 Hat, White, Flat Bill, S/M 1
SP423L AE 2012 Hat, White, Flat Bill, L/XL 1
SP424S AE 2012 Hat, White, Curved Bill, S/M 1
SP424L AE 2012 Hat, White, Curved Bill, L/XL 1
715 Reedy 2009 Track Banner 1
110684 Team Associated Track Banner 1

** Use part number plus the desired size when ordering!

 49
:: RePlay Cameras :: Contact Information
RP001 Replay XD1080 Complete Camera System 1
RP002 Replay XD720 Complete Camera System 1
RP021 Replay XD1080 Lens Bezel Kit 1
Associated Electrics, Inc.
RP022 Replay XD1080 Clear Lens Cover 1 26021 Commercentre Drive
RP023 Replay XD1080 Lens Bezel & Rear Cap O-Ring 1 Lake Forest, CA 92630-8853 USA
RP029 Replay XD1080 HDMI to Mini-HDMI 1 http://www.TeamAssociated.com
RP030 Replay XD1080 Mini 8-pin USB Charge Data Cable 1
RP032 USB DC Car Charger 1A Stubby 1
http://www.RC10.com
RP033 USB DC Car Charger 500mAh 1 http://twitter/Team Associated
RP034 Micro SDHC USB Reader 1 http://bit.ly/AEonFacebook
RP036 3M VHB 4991 Mount Adhesive for SnapTray 1
RP037 3M VHB 5962 Mount Adhesive for Pro Flat Mount 1
RP038 3M VHB 5962 Mount Adhesive for SnapTray 1
call: (949) 544-7500
RP041 Replay XD Suction Cup Arm Mini Clamp 1 fax: (949) 544-7501
RP042 Replay XD Suction Cup Short Arm Base 1 Check out the following web sites for all of our
RP043 Replay XD Skateboard Mount 1 electric kits, current products, new releases,
RP044 Replay XD VHB SnapTray, Convex 1
RP045 Replay XD VHB SnapTray, Flat 1
setup help, tips, and racing info!
RP046 Au Plug for Universal DC Wall Charger 1
RP047 Eu Plug for Universal DC Wall Charger 1 www.TeamAssociated.com. - www.RC10.com
RP048 Uk Plug for Universal DC Wall Charger 1
RP049 Universal USB DC Wall Charger 1A 1
RP054 RePlae ReView Field Monitor 1

:: Notes
50
:: Notes
 Driver: RC8.2 RTR Setup Date:
Track: Event:
Setup Sheet Conditions: Rev.1
Front Suspension Rear Suspension
Anti Roll Bar: Steering System: Anti Roll Bar:
3 3
2.2mm Black Stock Rack 2.2mm Black
1 1
2.5mm Silver Swing Rack 2.5mm Silver
2.8mm Gold Bellcrank Rack 2.8mm Gold
3.0mm Black back 3.0mm Black
mid
Bumpsteer front Wheelbase:
Washers: 0
Long
Camber: -1 Medium
Upper Hinge Short
Caster: 16 deg Pin Bushing
6 3
1 dot 5 2
Toe: 0 Front # Camber: -2 4
Up Down
B A BA C
Rear # 2 dot
Up Down Toe Bushing
D-Plate
B-Plate Type
# 3 degree
Low Original In Out

Kickup Bushing Hub: Squat Bushing

A-Plate Upper C-Plate
Lower
O I O I
# 2 dot # 2 dot
Ride Height: 29mm Up Down Ride Height: 29mm Up Down

Front Shocks Rear Shocks

Spring: Front Silver 3.9 Shock Cap: Alum. Spring: Rear Silver 3.3 Shock Cap: Alum.
Shock Fluid: 40 weight Length: 102mm Shock Fluid: 30 weight Length: 120mm
Piston: 16mm Rebound: None Piston: 16mm Rebound: None
Chassis Braces / Wheel Hex Chassis Weight Rear Hubs Differentials
Chassis Braces: Wheel Hex: Weight: Rear Hubs: Front Diff Fluid: 5,000
Pivot Narrow Center Diff Fluid: 5,000
Molded Wide Standard Rear Diff Fluid: 5,000
Aluminum CNC FT Alum. Notes:
Body / Wing Gearing / Clutch Drivetrain Engine
Body Type: Spur Gear: 44T Dogbone: Engine: Reedy .21 VS Pullstart
Wing Type: Clutch Bell: 16T Restrictor: Temp:
Clutch Shoes: Fiber CVA: Muffler: RTR Tuned Pipe
Gap to Tower (MM): Clutch Spring: 1.0 x3 Glow Plug: Fuel:
Tires Radio / Servos
Tire (F/R): / Radio:
Compound (F/R): / Steering Servo: Steering Expo:
Inserts (F/R): / Brake Expo:
Wheel (F/R): / Initial Brake: Drag Brake:
Notes: Dual Rate:
Race and Vehicle Comments Track Info
Qualify: Main: Finish: TQ: Traction: High Medium Low
Comments:
Surface: Smooth Bumpy Blue Groove
Soft Dirt Grass Clay Wet
Astroturf Dusty Other:

:: For more setups, visit RC10.com and click on “Setup Sheets”

 52
:: Hardware - 1:1 Scale View
Flat Head (fhcs) Cap Head (shcs) Button Head (bhcs)

3x8mm (25201) 2.5x8mm (89222) 2.5x3mm (89201)

3x10mm (25202) 3x8mm (89223) 2.5x6mm (31520)

3x12mm (25203) 3x10mm (25620) 3x6mm (31531)

3x14mm (89208) 3x12mm (89454) 3x10mm (25211)

3x16mm (89224) 3x16mm (89224) 3x12mm (89202)

3x18mm (89209) 3x18mm (25191) 3x14mm (25187)

3x20mm (89210) 3x20mm (25192) 3x16mm (89203)

3x22mm (89455) 3x22mm (89474) 3x18mm (2308)

3x26mm (89211) 3x24mm (89225) 3x20mm (25188)

4x6mm (89213) 3x26mm (89226) 3x24mm (89204)

4x12mm (89214) 3x28mm (89227) 3x26mm (89205)

4x14mm (89217) 3x40mm (89228)

3x35mm (89453)

3x45mm (89279)
4x10mm (89206)

Ball Bearings 3x50mm (89452)

4x12mm (89207)
steering bearing
(89161)
Set Screws Shims and Washers

3x3mm (25225) Ballstud Washer (9630)

5x10mm (25237)

3x5mm (89219) 3x5.6mm Steel Washer

(89528)

6x10mm (31404) 3x10mm (4671)

2.5mm Washer (89278)

4x5mm (25226)
3x8mm Thin Washer
(89218)
8x16mm (25236) 4x12mm (89220)

Diff Washer (89120)

5x4mm (89221)

Diff Shim (89117)

15x21mm (89162)
 Driver: Date:
Track: Event:
Setup Sheet Conditions: Rev.1
Front Suspension Rear Suspension
Anti Roll Bar: Steering System: Anti Roll Bar:
3 3
2.2mm Black Stock Rack 2 2.2mm Black 2
1 1
2.5mm Silver Swing Rack 2.5mm Silver
2.8mm Gold Bellcrank Rack 2.8mm Gold
3.0mm Black back 3.0mm Black
mid
Bumpsteer front Wheelbase:
Washers:
Long
Camber: Medium
Upper Hinge Short
Caster: Pin Bushing
6 3
5 2
Toe: Front # Camber: 4 1
Up Down
B A BA C
Rear #
Up Down Toe Bushing
D-Plate
B-Plate Type
#
Low Original In Out

Kickup Bushing Hub: Squat Bushing

A-Plate Upper C-Plate
Lower
O I O I
# #
Ride Height: Up Down Ride Height: Up Down

Front Shocks Rear Shocks

Spring: Shock Cap: Spring: Shock Cap:
Shock Fluid: Length: Shock Fluid: Length:
Piston: Rebound: Piston: Rebound:
Chassis Braces / Wheel Hex Chassis Weight Rear Hubs Differentials
Chassis Braces: Wheel Hex: Weight: Rear Hubs: Front Diff Fluid:
Pivot Narrow Center Diff Fluid:
Molded Wide Standard Rear Diff Fluid:
Aluminum CNC FT Alum. Notes:
Body / Wing Gearing / Clutch Drivetrain Engine
Body Type: Spur Gear: Dogbone: Engine:
Wing Type: Clutch Bell: Restrictor: Temp:
Clutch Shoes: CVA: Muffler:
Gap to Tower (MM): Clutch Spring: Glow Plug: Fuel:
Tires Radio / Servos
Tire (F/R): / Radio:
Compound (F/R): / Steering Servo: Steering Expo:
Inserts (F/R): / Brake Expo:
Wheel (F/R): / Initial Brake: Drag Brake:
Notes: Dual Rate:
Race and Vehicle Comments Track Info
Qualify: Main: Finish: TQ: Traction: High Medium Low
Comments:
Surface: Smooth Bumpy Blue Groove
Soft Dirt Grass Clay Wet
Astroturf Dusty Other:

:: For more setups, visit RC10.com and click on “Setup Sheets”

 Associated Electrics, Inc.
26021 Commercentre Dr.
Lake Forest, CA 92630 USA
http://www.TeamAssociated.com
http://www.RC10.com
http://twitter/Team_Associated
http://bit.ly/AEonFacebook
call: (949) 544-7500 - fax: (949) 544-7501
Check out the following web sites for all of our kits,
current products, new releases, setup help, tips, and racing info!
www.TeamAssociated.com. - www.RC10.com