FERROTECT ZINC PHOSPHATE PRIMER
Alkyd Primer
Anti- Corrosive primer for steel
Excellent Adhesion and durability
Quick Dry
Excellent rust inhibitor
Resistant to Mild Corrosive Chemicals
Ferrotect Zinc Phosphate Primer is a premium quality alkyd based rust inhibitive primer for priming on iron and
steel for non immersion condition. Suitable for use under a wide variety of conventional finishes combining
excellent adhesion and ease of application.
Recommended Usage
Recommended for use on general structural steel like bridges , cranes , towers , equipment , tanks , etc on
both interior and exterior surfaces and all suitably prepared non ferrous surfaces.
General Properties
Finish Matt Flexibility Excellent
Resistant to mild Acid &
Colour Grey Acid & Alkali Resistance
Alkali
Paint Type Solvent based Consistency Smooth & Uniform
Type Single pack Weather Resistance Satisfactory
Excellent with suitable
Weather ability Abrasion Resistance Moderate
top coat
Safety, Environment & Health
Flammable – Avoid Exposure to
Flash Point - Not below 30 oC
flame
Application
Brush Brush Roller 0-5% by volume
with J&N GP
Application Roller Dilution Airless Spray 0-5% by volume
with J&N GP
Spray Spray 10-15% by
volume with
Touch Dry : 1-2 hours Handle : 6-8 Over coating interval at Overnight
Drying time at 30 C hours 30 C
Hard Dry : overnight ( No. of coats specified 1-2 coats
dependent on temperature and
Recommended DFT 30- 45 microns dry film per coat Coverage (Theoretical) *17.0 sq mt / lt per coat at 20
micron dft * 13.5 sq mt/
Surface Preparation:
1. Cleaning: Free the surface from grease, rust, moisture, loose particles and peeling/flaking paint. Oil and grease should be removed as per SSPC -SP1 solvent cleaning.
Application:
Stir thoroughly before use .Apply one or two coats of Ferrotect Zinc phosphate primer
Stability of Thinned Paint Use within 24 hrs.
• Substrate Temperature should be at least 10 0C. but not above 50 0C.
• Painting is not recommended if the moisture content and alkalinity of the surface is high.
Precautions while Painting
• Relative humidity should be below 85 %
• Please do not over-thin or over-extend the brush while painting.
Cleaning up equipments All equipments should be cleaned with J&N GP Thinner.
Post Application Instructions To remove stains, sponge clean with a mild soap solution and wipe clean. Before cleaning, please ensure a drying time of one week.
General Information
Mixing VOCand inMax
Mix thoroughly before starting between
450 g/aslt)well
Conten
• 20 Ltr Packs
Packing
General Safety and Environment Information
• Keep container upright and tightly closed in a cool, dry and well ventilated • Wear appropriate attire, especially gloves, eye protection and nose mask.
location away from heat source, flammables and direct sunlight.
• Keep out of reach of children. Do not store near food, drinks or animal feed. • Work in a well-ventilated area. Do not breathe vapour or spray.
• Dispose unwanted paint safely. Do not dispose into drains, water sources or • Remove paint from skin by washing with water and soap or appropriate
open sewers. cleaner.
• Wash all tools after application with General Purpose Thinner or Mineral • Avoid contact with skin as it may cause irritation.
Turpentine.
• Use sand or earth to contain any paint spillage. • In the case of accidental contact, wash area immediately with water and
seek immediate medical attention.
• To remove the paint from skin, use soap and water or appropriate cleaner.
*Actual Coverage may vary depending upon the application process and surface conditions.
The information given is intended to give a description of the product performance under specific test conditions. Nevertheless, we cannot assume any responsibility for the use of it since ci
