PROVISIONAL PRODUCT DATA SHEET
SikaGrout®-114 QA
CEMENTITIOUS, SHRINKAGE COMPENSATED, GENERAL PURPOSE GROUT
DESCRIPTION CHARACTERISTICS / ADVANTAGES
SikaGrout®-114 QA is a cementitious, free flowing, SikaGrout®-114 QA is an economical and easy to use grout
general purpose, non-shrink general purpose grout requiring only the addition of water. It offers the fol-
with high ultimate strength. lowing beneficial properties:
Suitable for use in hot and tropical climatic conditions. ▪ Easy to mix
▪ Good flow characteristics
USES ▪ Dual expansion system
▪ Adjustable consistency
SikaGrout®-114 QA is used for grouting in the ▪ High final strengths
following: ▪ Non-corrosive and iron-free
▪ Machine foundations
▪ Columns in pre-cast construction APPROVALS / CERTIFICATES
▪ Concrete anchors, cavities, gaps and recesses
▪ Base plates SikaGrout®-114 QA follows the main requirements of
▪ General concrete repairs ASTM C1107
▪ Bridge bearings pads
PRODUCT INFORMATION
Chemical base Portland cement, selected fillers and aggregates, special additives
Packaging 25 kg bag
Appearance / Colour Grey Powder
Shelf life 12 months minimum from date of production.
Storage conditions Store in a dry area in original sealed packaging at temperatures between
+5°C and +35 °C. Protect from direct sunlight, heat and moisture.
Maximum Grain Size ~4 mm
Provisional Product Data Sheet
SikaGrout®-114 QA
December 2019, Version 1.0
1/3
TECHNICAL INFORMATION
Compressive Strength 07 Days 28 Days (ASTM C109)
W/P ratio = ~45 N/mm2 ~60 N/mm2
0.13 (3.25 L
water / 25
kg)
Tensile Adhesion Strength ~ 1.5 N/mm2 (or concrete failure) (ASTM D4541)
APPLICATION INFORMATION
Mixing Ratio Consistency Water per 25 kg bag Water / Powder ratio
Flowable (max. 3.00 - 3.25 L 0.12 - 0.13
strength)
Highly flowable (max. 3.25 - 3.75 L 0.13 - 0.15
flow)
Fresh Mortar Density ~2.20 kg/l (+25 °C)
Yield ~10.8 L / 25 kg bag, depending on water addition
Layer Thickness Min. 10 mm per pour
Max. 75 mm per pour
Ambient Air Temperature +5 °C min. / +35 °C max.
Substrate Temperature +5 °C min. / +35 °C max.
Pot Life ~1 h (25 °C)
APPLICATION INSTRUCTIONS MIXING
SUBSTRATE QUALITY / PRE-TREATMENT Add water according to the desired consistency into a
clean mixing vessel before slowly adding the Sik-
Concrete: aGrout®-114 QA powder. SikaGrout®-114 QA is best
The concrete shall be thoroughly clean, rough, free mixed in a forced action mixer, for 2 to 3 minutes or
from dust, oil, greas, loose material, surface contamin- until the mix is free of lumps, not longer than 5
ation and materials which reduce bond or prevent suc- minutes. Slow speed drill (maximum 500 rpm) can be
tion or wetting by repair materials. De-laminated, also used for mixing. Normal tumble type concrete
weak, damaged and deteriorated concrete and where mixers are not suitable. Do not add extra water or
necessary sound concrete shall be removed by suit- other ingredients. Mix only full bags for best results.
able means. Absorbent surfaces should be saturated
thoroughly with clean water. APPLICATION
The application of a suitable bonding agent, such as Before pouring let the mixed grout stand for approx-
Sikadur®-32 LP or SikaTop® Armatec®-110 EpoCem®, imately 5 minutes after mixing to allow entrapped air
will improve adhesion on large areas or where particu- to escape. Pour into the prepared area such that the
larly dense concrete substrates are involved. grout has the shortest distance to travel. Ensure that
air displaced by the grout is allowed to escape. When
Steel Reinforcement: carrying out base plate grouting, ensure a sufficient
Rust, scale, mortar, concrete, dust and other loose and head of pressure is maintained to keep the mortar
deleterious material which reduces bond or contrib- flowing. All exposed areas of the mortar surface
utes to corrosion shall be removed. Surfaces shall be should be kept as small as possible.
prepared using abrasive blast cleaning techniques or
high pressure water-blasting to SA 2 (ISO 8501-1) CURING TREATMENT
Embedded steel reinforcing should be treated with a
suitable anticorrosion coating such as SikaTop® Treat exposed surfaces with Antisol®-WB curing com-
Armatec®-110 EpoCem®. pounds or use other approved curing methods such as
polyethylene sheeting or wet hessian. Do not com-
Reference shall be made to EN1504-10 for specific re- mence fogging until final set has been reached.
quirements.
CLEANING OF EQUIPMENT
Clean equipment and mixer immediately after applica-
tion with water. Hardened material can only be re-
moved mechanically.
Provisional Product Data Sheet
SikaGrout®-114 QA
December 2019, Version 1.0
2/3
FURTHER INFORMATION LEGAL NOTES
Method Statement The information, and, in particular, the recommenda-
tions relating to the application and end-use of Sika
IMPORTANT CONSIDERATIONS products, are given in good faith based on Sika's cur-
rent knowledge and experience of the products when
▪ Ensure formwork is secure and watertight to prevent properly stored, handled and applied under normal
movement and leaking during placing and curing. conditions in accordance with Sika's recommenda-
▪ Where maximum thickness exceeds 75 mm, consider tions. In practice, the differences in materials, sub-
the use of SikaGrout®-275. strates and actual site conditions are such that no war-
▪ At high temperatures, use chilled water for mixing to ranty in respect of merchantability or of fitness for a
keep grout mix temperature below 30 °C. particular purpose, nor any liability arising out of any
▪ In hot weather, base plates and foundations must be legal relationship whatsoever, can be inferred either
shaded from direct sunlight. Condition bags of grout from this information, or from any written recom-
< 30 °C prior to use. mendations, or from any other advice offered. The
▪ SikaRep® thixotropic fine mortars can be used to fix user of the product must test the product’s suitability
shims and alignment plates before grouting. for the intended application and purpose. Sika re-
▪ Depending on requirements and site condition, the serves the right to change the properties of its
addition of single size, clean coarse aggregates is pos- products. The proprietary rights of third parties must
sible up to 100 % by weight of the dry grout powder. be observed. All orders are accepted subject to our
Trials are recommended to confirm suitability of ag- current terms of sale and delivery. Users must always
gregates to be employed. refer to the most recent issue of the local Product Data
▪ For additional information on SikaGrout®-114 or oth- Sheet for the product concerned, copies of which will
er grouting materials contact Sika Technical Depart- be supplied on request.
ment.
BASIS OF PRODUCT DATA
All technical data stated in this Data Sheet are based
on laboratory tests. Actual measured data may vary
due to circumstances beyond our control.
LOCAL RESTRICTIONS
Note that as a result of specific local regulations the
declared data and recommended uses for this product
may vary from country to country. Consult the local
Product Data Sheet for the exact product data and
uses.
ECOLOGY, HEALTH AND SAFETY
For information and advice on the safe handling, stor-
age and disposal of chemical products, users shall refer
to the most recent Safety Data Sheet (SDS) containing
physical, ecological, toxicological and other safety-re-
lated data.
SIKA Qatar W.L.L
Building 144, Street # 2,
New Industrial Area, Doha –
Qatar
gcc.sika.com
Provisional Product Data Sheet
SikaGrout®-114 QA
December 2019, Version 1.0
3/3
