10FT TRAMPOLINE

ASSEMBLY MANUAL

VERSION 2 VISIT: tuffbounce.com.au

PARTS OR GENERAL ENQUIRIES: info@tuffbounce.com.au
SAFETY INFORMATION
MUST READ BEFORE USE

THE FOLLOWING SAFETY STEPS MUST BE APPLIED

WHEN USING THIS PRODUCT.
The following steps must
IMPROPER USEbeCOULD
following when
LEAD TO using this INJURY
SERIOUS product.OR DEATH.

1. Two people are required in order to 9. The trampoline must always maintain
assemble this product. Assembly can take a clearance of 5m vertically from the
two hours to fully complete. bounce mat upwards from surrounding
objects (roofs or overhanging branches),
2. Never use this product if the assembly as well as 1.5m on any given side. (Shown
process has not been completed as per in diagram on page 3). This is to prevent
the instructions in this user guide. users from making unwanted contact with
overhanging or nearby objects.
3. Springs and moving parts during assembly
are treated as parts under pressure. 10. Trampoline must not be placed on top
Children should be at least 5m from of objects, nor can objects be stored
adults assembling the product. Children underneath or around it.
should never be involved during this stage.
Children are at far greater risk of serious 11. Trampoline must only be used in daylight
injury from improper assembly. Take hours and never in poorly lit areas.
caution when attaching springs.
12. The owner is responsible for assuring all
4. If a part of the trampoline is faulty or ages users are aware of rules and guidelines
excessively. Replace only with Tuff Bounce within this book prior to use.
parts.
13. Do not attempt flips or somersaults.
5. Children under the age of 6 must not use
this product. 14. Do not attempt to overload the trampoline.
Ensure a 1 person maximum limit is
6. A legal adult must supervise use at all observed at all times.
times.
15. Do not exceed the 150kg weight limit of the
7. The trampoline must be exposed to the trampoline at any time.
elements as little as possible.
16. Ensure the safety net is properly
8. The trampoline must never be placed on a assembled, secured and zipped closed
slope or gradient when in use or otherwise. before use. Failure to do this can result in
serious injury or death.
TRAMPOLINE
LOCATION
REQUIREMENT

Correct installation trampoline location requirements must be observed at all times.

TRAMPOLINE
PART LIST
PART IMAGE QTY PART IMAGE QTY

Safety Net Pole

Spring Tool 1 Clamp (Male & 8 Pairs
Female)

PVC Pole
Spring 72 8
Sleeve

Upper Pole
Bounce Mat 1 8
(with foam)

Lower Pole
Spring Cover 1 8
(with foam)

Safety Net 1 Nylon Cord 1

U-Shaped Fibreglass
4 2
Leg Rod

Leg
8 Spanner 1
Extension

Bolt/Nut for
T-Connector
8 Lower Poles 16 Sets
Sleeve
(6x75mm)

Bolt/Nut for
T-Connectors &
Frame Tube 8 16 Sets
Leg Extension
(8x50mm)

Spacers
16
for Legs
 1 2

Locate the U-Shaped leg bases to form the Connect the legs and their extensions together.
underside of your trampoline. Securing process shown in step 3.

3 4

Thread the leg Bolts through the connected leg Slide the T-Connector Sleeves onto each Frame
holes. Tighten all 8 Nuts using the Spanner. Tube and sequentially connect all Frame Tubes
together.

5 6

Layout the Frame Tubes with T-Connector Guide the T-Connector Bolts through each hole
Sleeves on the ground in one large ring. Ensure from the outside of the Frame and fasten with
the Frame Tube holes are all facing upwards. a washer and nut. Tighten all 8 Nuts using the
Spanner.
 7 8

Attach your Legs into T-Connector Sleeves. Do Once assembled your trampoline base is ready
not secure with screws at this stage. to stand on its own.

9 10

The Lower Poles form the support for the Safety This diagram shows the parts required for this
Net. They attach to the outside of each leg with step in order.
the top curved away from the trampoline centre.

11 12

Guide the Leg Bolts through both poles with a Your trampoline should look like this.
Spacer in between and secure with Leg Nuts.
Ensure the Lower Poles are mounted on the
outside of the trampoline leg.
 13 14

Place your Bounce Mat on the ground in the On each side of the T-Connector Sleeves, attach
middle of the trampoline frame. Springs from the Bounce Mat buckles to the
Frame Tube holes. Use the Spring Tool to extend
and hook each Spring.

15 16

It should look like this. Ensure the Frame Tube Evenly attach each Spring to the Mat and Frame
holes and the Bounce Mat buckles match in using this Leg number sequence: 1, 5, 3, 7, 2, 6, 4,
value between the legs. 8. Repeat the same pattern until all the Springs
are attached.

17 18

Your trampoline is now beginning to take form. Lay the Spring Cover on top of the springs
equally around the trampoline. Locate the black
elastic ties on its underside.
 19 20

Firmly secure the Spring Cover ties to the Frame Evenly weave the black Nylon Cord between the
Tube. These steps are paramount for user safety Spring Cover mesh and the Bounce Mat buckles
so please ensure the knots are tight. in a zig-zag fashion. Tighten and then tie off.

21 22

Locate the Upper Poles. These will complete the Guide the Safety Net Upper Poles into the Lower
Safety Net structure. Poles while depressing each metal button. You
should hear a click when securely in place.

23 24

Slide the black PVC Pole Sleeves over each of Connect the 2 Fiberglass Rods together to form
the Safety Net Poles. 1 large rod. Feed the Rod through the Safety
Net sleeves. Join the 2 ends of the rod together
forming the top ring of your Safety Net.
 25 26

Place the Safety Net on top of your Bounce Mat Connect male and female parts of a Safety
inside the poles, ready to be connected to the Net Pole Clamp. Slot the Pole Clamp onto the
top of each Safety Net Upper Pole. Fiberglass Rod and guide onto the top of the
Upper Pole click.
27 28

You should hear the button click when the Locate the plastic hooks at the bottom of the
clamp is engaged properly. This may require a Safety Net and connect them to the closest
second person to help. Repeat on all 8 Upper Bounce Mat buckle.
Poles.
29 30

An engaged safety net hook should look like Observe that the Safety Net hangs inside the
this. poles, but over the outside of the Frame Tubes
and Spring Cover. Your trampoline is now
complete.
If you think anything is missing from your package,
has been damaged in transit or you have any other
issue, please contact us at:

info@tuffbounce.com.au

tuffbounce.com.au