LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Downsized snap-ins, 105℃

KHE
・Upgraded capacitance rating
Series KHE

Downsized
・Endurance with ripple current : 2,000 hours at 105℃
・Rated voltage range : 400 to 450Vdc, Capacitance range : 210 to 1,500µF KMZ
・Non solvent resistant type
・RoHS2 Compliant

◆SPECIFICATIONS
Items Characteristics
Category
-40 to +105
Temperature Range
Rated Voltage Range 400 to 450Vdc
Capacitance Tolerance 20% (M) (at 20 , 120Hz)
Leakage Current I 3 CV
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V) (at 20 after 5 minutes)
Dissipation Factor Rated voltage (Vdc) 400 to 450V
(tan ) tan (Max.) 0.20 (at 20 , 120Hz)
Low Temperature Rated voltage (Vdc) 400 to 450V
Characteristics Z(-25 )/Z(+20 ) 8
(Max. Impedance Ratio)
(at 120Hz)
Endurance The following specifications shall be satisfied when the capacitors are restored to 20 after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 2,000 hours at 105 .
Capacitance change 20% of the initial value
D.F. (tan ) 200% of the initial specified value
Leakage current The initial specified value
Shelf Life The following specifications shall be satisfied when the capacitors are restored to 20 after exposing them for 1,000 hours at 105 without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change 15% of the initial value
D.F. (tan ) 150% of the initial specified value
Leakage current The initial specified value

◆DIMENSIONS [mm]
●Terminal Code : VS (φ25.4 to φ35) : Standard ●Terminal Code : LI (φ30,φ35)
PC board pin-out PC board pin-out
Sleeve (PET : Brown) Negative mark (View from Solder side) Sleeve (PET : Brown) Negative mark (View from Solder side)

4.2±0.5
2-1.2×6
10

φD+1max.
φD+1max.

2-φ2 5±0.5
L±2.5 4.0±0.5 L±2.5 4.5±1 14.2±1
Vent Vent

The standard design has no plastic disc.

◆PART NUMBERING SYSTEM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

E KH E VS N M Z
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 470µF:471, 1,000µF:102)
Dummy terminal code
Terminal code (VS, LI)
Voltage code (ex. 400V:401, 450V:451)
Series code
Category

Please refer to "Product code guide (snap-in type)"

Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.

CAT. No. E1001Y 2024

 LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS Downsized snap-ins, 105℃

KHESeries
◆STANDARD RATINGS
Rated ripple Rated ripple
WV Cap Case size current WV Cap Case size current
tan Part No. tan Part No.
(Vdc) (µF) D L(mm) (Arms/ (Vdc) (µF) D L(mm) (Arms/
105 , 120Hz) 105 , 120Hz)
240 25.4 25 0.20 1.17 EKHE401VSN241MQ25Z 670 30 40 0.20 2.15 EKHE421VSN671MR40Z
310 25.4 30 0.20 1.37 EKHE401VSN311MQ30Z 720 25.4 60 0.20 2.42 EKHE421VSN721MQ60Z
370 30 25 0.20 1.50 EKHE401VSN371MR25Z 730 35 35 0.20 2.00 EKHE421VSN731MA35Z
390 25.4 35 0.20 1.60 EKHE401VSN391MQ35Z 770 30 45 0.20 2.36 EKHE421VSN771MR45Z
460 25.4 40 0.20 1.77 EKHE401VSN461MQ40Z 870 35 40 0.20 2.26 EKHE421VSN871MA40Z
470 35 25 0.20 1.55 EKHE401VSN471MA25Z 880 30 50 0.20 2.57 EKHE421VSN881MR50Z
420
480 30 30 0.20 1.73 EKHE401VSN481MR30Z 980 30 55 0.20 2.76 EKHE421VSN981MR55Z
530 25.4 45 0.20 1.94 EKHE401VSN531MQ45Z 1,010 35 45 0.20 2.49 EKHE421VSN102MA45Z
590 30 35 0.20 1.96 EKHE401VSN591MR35Z 1,080 30 60 0.20 2.96 EKHE421VSN112MR60Z
600 25.4 50 0.20 2.10 EKHE401VSN601MQ50Z 1,150 35 50 0.20 2.71 EKHE421VSN1B2MA50Z
620 35 30 0.20 1.81 EKHE401VSN621MA30Z 1,290 35 55 0.20 2.90 EKHE421VSN132MA55Z
680 25.4 55 0.20 2.30 EKHE401VSN681MQ55Z 1,430 35 60 0.20 3.07 EKHE421VSN1E2MA60Z
400
700 30 40 0.20 2.20 EKHE401VSN701MR40Z 210 25.4 25 0.20 1.10 EKHE451VSN211MQ25Z
750 25.4 60 0.20 2.47 EKHE401VSN751MQ60Z 270 25.4 30 0.20 1.28 EKHE451VSN271MQ30Z
760 35 35 0.20 2.04 EKHE401VSN761MA35Z 320 30 25 0.20 1.39 EKHE451VSN321MR25Z
810 30 45 0.20 2.42 EKHE401VSN811MR45Z 330 25.4 35 0.20 1.48 EKHE451VSN331MQ35Z
910 35 40 0.20 2.31 EKHE401VSN911MA40Z 400 25.4 40 0.20 1.65 EKHE451VSN401MQ40Z
930 30 50 0.20 2.64 EKHE401VSN931MR50Z 400 35 25 0.20 1.43 EKHE451VSN401MA25Z
1,030 30 55 0.20 2.83 EKHE401VSN1A2MR55Z 410 30 30 0.20 1.59 EKHE451VSN411MR30Z
1,060 35 45 0.20 2.55 EKHE401VSN1A2MA45Z 460 25.4 45 0.20 1.81 EKHE451VSN461MQ45Z
1,140 30 60 0.20 3.04 EKHE401VSN1B2MR60Z 510 30 35 0.20 1.82 EKHE451VSN511MR35Z
1,210 35 50 0.20 2.78 EKHE401VSN122MA50Z 520 25.4 50 0.20 1.95 EKHE451VSN521MQ50Z
1,350 35 55 0.20 2.97 EKHE401VSN1D2MA55Z 530 35 30 0.20 1.67 EKHE451VSN531MA30Z
1,500 35 60 0.20 3.15 EKHE401VSN152MA60Z 580 25.4 55 0.20 2.13 EKHE451VSN581MQ55Z
450
230 25.4 25 0.20 1.15 EKHE421VSN231MQ25Z 600 30 40 0.20 2.03 EKHE451VSN601MR40Z
300 25.4 30 0.20 1.35 EKHE421VSN301MQ30Z 640 25.4 60 0.20 2.28 EKHE451VSN641MQ60Z
350 30 25 0.20 1.46 EKHE421VSN351MR25Z 660 35 35 0.20 1.90 EKHE451VSN661MA35Z
370 25.4 35 0.20 1.56 EKHE421VSN371MQ35Z 690 30 45 0.20 2.23 EKHE451VSN691MR45Z
440 25.4 40 0.20 1.74 EKHE421VSN441MQ40Z 780 35 40 0.20 2.14 EKHE451VSN781MA40Z
440 35 25 0.20 1.51 EKHE421VSN441MA25Z 790 30 50 0.20 2.43 EKHE451VSN791MR50Z
420
460 30 30 0.20 1.68 EKHE421VSN461MR30Z 890 30 55 0.20 2.63 EKHE451VSN891MR55Z
510 25.4 45 0.20 1.90 EKHE421VSN511MQ45Z 910 35 45 0.20 2.36 EKHE451VSN911MA45Z
560 30 35 0.20 1.91 EKHE421VSN561MR35Z 1,000 30 60 0.20 2.83 EKHE451VSN102MR60Z
570 25.4 50 0.20 2.05 EKHE421VSN571MQ50Z 1,040 35 50 0.20 2.58 EKHE451VSN1A2MA50Z
580 35 30 0.20 1.75 EKHE421VSN581MA30Z 1,160 35 55 0.20 2.75 EKHE451VSN1B2MA55Z
640 25.4 55 0.20 2.23 EKHE421VSN641MQ55Z 1,290 35 60 0.20 2.92 EKHE451VSN132MA60Z

◆RATED RIPPLE CURRENT MULTIPLIERS

・Frequency Multipliers
Frequency(Hz) 50 120 300 1k 10k 50k
Multipliers 0.77 1.00 1.10 1.21 1.32 1.33
The deterioration of aluminum electrolytic capacitors accelerates their life due to the internal heating produced by ripple current. For details, refer
to Section "5-3 Ripple Current Effect on Lifetime" in the catalog, Technical Note.

Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.

CAT. No. E1001Y 2024

 ALUMINUM ELECTROLYTIC CAPACITORS Product Guide

Always read "Notes on Use" before using the product in order to enable you to use the product correctly and prevent any faults
and accidents from occurring.

Request the Product Specification on the product of NIPPON CHEMI-CON CORPORATION to refer to it as well as this brochure
prior to the order of the products. Some specific notes on use of the ordered product may be described in the specifications.

The products listed in this catalog are designed and manufactured for general electronics equipment use and are not intended for
use in applications that can adversely affect human life; where the malfunction of equipment may cause damage to life or
property. In addition, our products are not intended to be used in specific applications that may cause a major social impact.
Please consult with us in advance of usage of our products in the following listed applications. Aerospace equipment Power
generation equipment such as thermal power, nuclear power etc. Medical equipment Transport equipment (automobiles,
trains, ships, etc.) Transportation control equipment Disaster prevention / crime prevention equipment Highly publicized
information processing equipment Submarine equipment Other applications that are not considered general-purpose
applications.

The circuits described as examples in this catalog and the "delivery specifications" are featured in order to show the operations
and usage of our products, however, this fact does not guarantee that the circuits are available to function in your equipment
systems. We are not in any case responsible for any failures or damage caused by the use of information contained herein. You
should examine our products, of which the characteristics are described in the "delivery specifications" and other documents, and
determine whether or not our products suit your requirements according to the specifications of your equipment systems.
Therefore, you bear final responsibility regarding the use of our products.
Please make sure that you take appropriate safety measures such as use of redundant design and malfunction prevention
measures in order to prevent fatal accidents and/or fires in the event any of our products malfunction.

We strongly recommend our customers to purchase Nippon Chemi-Con products only through our official sales channels. We
assume no responsibility for any defects or damages caused by using products purchased from outside our official sales channel
or of counterfeit goods. In addition, we will ask the customer to pay the investigation cost for products purchased outside our
official sales channel.

We reserve the right to discontinue production and delivery of products. We do not guarantee that all the products included in this
catalog will be available in the future.
The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific
products

We continually strive to improve the quality and reliability of our products, but in any case that our product does not meet our
published specifications, please stop using it promptly and contact us immediately. As for compensation for non-conforming
goods delivered by Chemi-Con, we will limit it only to goods found in non-compliance of our published specifications. This may be
accomplished by a no cost replacement of non-conforming individual products, a credit of the piece price paid per each individual
non-conforming product, or in other ways deemed necessary.
In addition, we have an established system with enhanced traceability, therefore we will limit the applicable lot items for any
potential compensation.

Part Numbering System

Part Numbering System (Appendix)
Standardization
Available Items by Manufacturing Locations
Environmental Measures
Technical Note
Precautions and Guidelines
Recommended Soldering Conditions
Taping, Lead-preforming and Packaging
Available Terminals for Snap-in and Screw Mount Type

Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.

CAT. No. E1001Y 2024