PROGRAM MANUAL

Direct thermal barcode printer & Thermal transfer label printer

GP-3120TN GP-9035T
GP-3120TL GP-9034T
GP-3150TIN GP-9026T
GP-1524D GP-9025T
GP-1625D GP-1125T
GP-1225D GP-1124T
GP-1124D GP-1225T

2016.12.10

Downloaded from www.Manualslib.com manuals search engine

 Table of contents
Document convention
System setup commands
 SIZE.......................................................................................................................................... 5
 GAP ............................................................................................................................................
 BLINE .........................................................................................................................................
 OFFSET .....................................................................................................................................
 SPEED .......................................................................................................................................
 DENSITY ....................................................................................................................................
 DIRECTION ................................................................................................................................
 REFERENCE .............................................................................................................................
 SHIFT .........................................................................................................................................
 CODEPAGE ...............................................................................................................................
 CLS ............................................................................................................................................
 FEED ..........................................................................................................................................
 BACKFEED&BACKUP .............................................................................................................
 FORMFEED ...............................................................................................................................
 HOME .........................................................................................................................................
 PRINT .........................................................................................................................................
 SOUND.......................................................................................................................................
 LIMITFEED ................................................................................................................................
 SELFTEST .................................................................................................................................
Label Formatting Commands
 BAR ........................................................................................................... 错误！未定义书签。
 BARCODE .................................................................................................................................
 BITMAP ......................................................................................................................................
 BOX ............................................................................................................................................
 ERASE .......................................................................................................................................
 PUTBMP ....................................................................................................................................
 PUTPCX .....................................................................................................................................
 QRCODE ....................................................................................................................................
 REVERSE ..................................................................................................................................
 TEXT ..........................................................................................................................................
Status Polling Commands (RS232)
 <ESC>!? ....................................................................................................................................
 <ESC>!R ....................................................................................................................................
 ~!@ .............................................................................................................................................
 ~!A ..............................................................................................................................................
 ~!C ..............................................................................................................................................
 ~!D ..............................................................................................................................................
 ~!F ..............................................................................................................................................
 ~!I ...............................................................................................................................................
 ~!T ..............................................................................................................................................
File Management Commands
 DOWNLOAD ............................................................................................. 错误！未定义书签。

Downloaded from www.Manualslib.com manuals search engine

  EOP ............................................................................................................................................
 FILES .........................................................................................................................................
 KILL............................................................................................................................................
 MOVE .........................................................................................................................................
 RUN ............................................................................................................................................
BASIC Commands and Functions
 ABS( ).........................................................................................................................................
 ASC( ).........................................................................................................................................
 CHR$( ) ......................................................................................................................................
 END ............................................................................................................................................
 EOF( ) .........................................................................................................................................
 OPEN .........................................................................................................................................
 READ .........................................................................................................................................
 SEEK ..........................................................................................................................................
 LOF( ) .........................................................................................................................................
 FREAD$( ) ..................................................................................................................................
 FOR…NEXT LOOP ...................................................................................................................
 IF…THEN…ELSE…ENDIF .......................................................................................................
 GOSUB…RETURN ...................................................................................................................
 GOTO .........................................................................................................................................
 REM............................................................................................................................................
 INT( ) ..........................................................................................................................................
 LEFT$( ) .....................................................................................................................................
 LEN( ) .........................................................................................................................................
 MID$( )........................................................................................................................................
 RIGHT$( ) ...................................................................................................................................
 STR$( ) .......................................................................................................................................
 VAL( ) .........................................................................................................................................
 BEEP ..........................................................................................................................................
Device Reconfiguration Commands
 SET COUNTER...................................................................................................................... 77
 SET KEY1, SET KEY2 ..............................................................................................................
 SET PEEL ..................................................................................................................................
 SET TEAR & SET STRIPPER ...................................................................................................
 SET HEAD .................................................................................................................................
 SET RIBBON .............................................................................................................................
 SET COM1 .................................................................................................................................
 SET PRINTKEY .........................................................................................................................
 SET REPRINT............................................................................................................................
 PEEL ..........................................................................................................................................
 KEY1, KEY2...............................................................................................................................
Printer Global Variables
 @LABEL .............................................................................................................................. 86

Downloaded from www.Manualslib.com manuals search engine

 Document Conventions
This manual uses the following typographic conventions.

Convention Description

[Expression list] Items inside square brackets are optional, expression

maximum length 2*1024 bytes;

<ESC> ESCAPE (ASCII 27), control code of status

polling command, which returns the printer
status immediately, no matter the printer is
standby status or busy.

~ (ASCII 126), control code of status polling

command, which returns the printer status
only when the printer is ready.

Note: 200 DPI: 1 mm = 8 dots Font in bold and italic type is used for note.

DOWNLOAD “TEST.BAS” When displayed content is program, use Arial 10.5 sized font.
SET COUNTER @1 1
@1=”0001”
TEXT 10,10,”3”,0,1,1,@1
PRINT 3,2
EOP

Downloaded from www.Manualslib.com manuals search engine

 System setup commands
 SIZE

Description
This command defines the label width and length.
Syntax
(1) English system (inch)
SIZE m, n
(2) Metric system (mm)
SIZE m mm, n mm

Parameter Description
m Label width (inch or mm)
n Label length (inch or mm)

Note:
200 DPI: 1 mm = 8 dots
300DPI: 1mm=12dots
For metric system, there must be a space between parameter m and “mm”.

Example
(1) English system (inch)
SIZE 3.5, 3.00
(2) Metric system (mm)
SIZE 100 mm, 100 mm

See Also
GAP, BLINE

Downloaded from www.Manualslib.com manuals search engine

  GAP

Description
Define the gap distance between two labels

Syntax
(1). English system (inch)
GAP m, n
(2) Metric system (mm)
GAP m mm, n mm

Parameter Description
m The gap distance between two labels(inch or mm)
0 ≤ m ≤ 1 (inch), 0 ≤ m ≤ 25.4 (mm)
n The offset distance of the gap(inch or mm)
[ ]n ≤ label length (inch or mm)
0,0 Continuous label.

Note: For metric system, there must be a space between parameter m and mm.
When the sensor type is changed from “Black Mark” to “GAP”, please send the “GAP”
command to the printer first.
Eg: In DOS mode,
C:\>copy con lpt1 <Enter>
GAP 2 mm,0 <Enter>
<Ctrl>+<Z> <Enter>
Example
Normal gap
(1). English system (inch)
GAP 0.12,0
(2) Metric system (mm)
GAP 3 mm,0
(3). Continuous label
GAP 0,0

Special gap
(1). English system (inch)
GAP 0.30, 0.10
(2). Metric system (mm)
GAP 7.62 mm, 2.54 mm

See Also
SIZE,BLINE

Downloaded from www.Manualslib.com manuals search engine

  BLINE

Description
Define black mark distance and extra label feeding length after printing

Syntax
(1) English system (inch)
BLINE m, n
(2) Metric system (mm)
BLINE m mm, n mm

Parameter Description
m The distance between two black marks
0.1 ≤ m ≤ 1 (inch), 2.54 ≤ m ≤ 25.4 (mm)
n Extra label feeding length (inch or mm)
0 ≤n ≤label length (inch or mm)
0,0 Continuous label.

Note: For metric system, there must be a space between parameter m and mm.
When the sensor type is changed from “GAP” to “Black Mark”, please send the
“BLINE” command to the printer first.
Eg: In DOS mode,
C:\>COPY CON LPT1 <Enter>
BLINE 2 mm,0<Enter>
<Ctrl>+<Z><Enter>

Example
(1) English system (inch)
BLINE 0.20,0.50
(2) Metric system (mm)
BLINE 5.08 mm,12.7 mm

See Also
SIZE, GAP

Downloaded from www.Manualslib.com manuals search engine

  OFFSET

Description
This command defines the selective, extra label feeding length, especially when you
use peeler or cutter function, this could be used to adjust the label stop position, the
extra feeding length or less feeding length could be backward pulled to adjust when
the second label is printed. This method is applied for peel-off mode and cutter
mode.

Syntax
(1) English system (inch)
OFFSET m
(2) Metric system (mm)
OFFSET m mm

Parameter Description
m The offset distance (inch or mm)
-1≤ m ≤1(inch)

CAUTION: Improper offset value may cause paper jam.

Example
(1) English system (inch)
OFFSET 0.5
(2) Metric system (mm)
OFFSET 12.7 mm

See Also
SIZE, GAP, SET PEEL

Downloaded from www.Manualslib.com manuals search engine

  SPEED

Description
This command defines the print speed.

Syntax
SPEED n

Parameter Description
n printing speed in inch per second

N 2 3 4 5 6 7 8
3120TN o o o o
3120TL o o o o
3150TIN o o o o o
1524D o o o o o o o
9035T o o o o
9025T o o o o
9026T o o o o
1124T o o o o
1125T o o o o
1235T o o o o

Example
SPEED 4

See Also
DENSITY

 DENSITY

Description
This command designates the level of darkness of printing.

Syntax
DENSITY n

Parameter Description
n 0~15
0, specifies the lightest level
15, specifies the darkest level
Example
DENSITY 7

See Also
SPEED

Downloaded from www.Manualslib.com manuals search engine

  DIRECTION
Description
This command defines the printout direction, and this will be memorized in EEPROM.

Syntax
DIRECTION n

Parameter Description
n 0 or 1. Please refer to the illustrations below:

Example
DIRECTION 0[,0]

See Also
REFERENCE

Downloaded from www.Manualslib.com manuals search engine

  REFERENCE

Description
This command defines the reference point of the label. The reference (origin)
point varies with the print direction, as shown:

x
y
y
x

Syntax
REFERENCE x, y

Parameter Description
x Horizontal coordinate, with “dot” as the unit.
y Vertical coordinate, with “dot” as the unit.

Note: 200 DPI: 1 mm = 8 dots

300DPI: 1 mm = 12 dots

Example
REFERENCE 10,10

See Also
DIRECTION

Downloaded from www.Manualslib.com manuals search engine

  SHIFT

Description
This command can be used to fine-tune the entire label up or down from its
current position. The position relates to the top edge of the label. A negative
value moves the entire label away from the top of the label; a positive value
moves the entire label to the top of label.

Syntax
SHIFT n

Parameter Description
n The maximum value is 1 inch. For 203 dpi printers,
the range is from –203 to 203; The unit is dot.

Example
SIZE 4,2.5
GAP 2 mm,0
DIRECTION 0
SHIFT 36
OFFSET 0
CLS
TEXT 400,200,"3",0,1,1,"DIRECTION 0"
TEXT 400,250,”3”,0,1,1,"SHIFT 36"
BOX 10,0,780,490,8
PRINT 3,1

See Also
OFFSET, REFERENCE

Downloaded from www.Manualslib.com manuals search engine

  CODE PAGE

Description
This command defines the code page of international character set.
Syntax
CODEPAGE n

Parameter Description
n name or number of code page, which can be divided
into 8-bit code page further.

8-bit code page number

437: United States
850: Multilingual
852: Slavic
860: Portuguese
863: Canadian/French
865: Nordic
857: Turkish

Windows code page

1250: Central Europe
1252: Latin I
1253: Greek
1254: Turkish

Note: 8-bit code page is determined by the communication parameter of DATA LENGTH

Example
CODEPAGE 437

 CLS

Description
This command clears the image buffer.

Syntax
CLS
Parameter Description
None N/A

Note: This command must be placed after SIZE command.

Example
CLS
See Also
SIZE, GAP, BLINE

Downloaded from www.Manualslib.com manuals search engine

  FEED
Description
This command feeds label with the specified length.
The length is specified by dot.

Syntax
FEED n

Parameter Description
n unit: dot
1 ≤ n ≤ 9999
Example
FEED 40

Note: 203 DPI: 1 mm = 8 dots

300DPI: 1mm = 12 dots

See Also
BACKFEED, SIZE, GAP, BLINE, HOME, FORMFEED

 BACKFEED & BACKUP

Description
To back feed label with the specified length. The length is specified by dot.

Syntax
BACKUP n
BACKFEED n

Parameter Description
n unit: dot
1 ≤ n ≤ 9999
Example
BACKUP 40
BACKFEED 40

CAUTION: Improper back feed value may cause paper jam or ribbon wrinkle.

Note: 203 DPI: 1 mm = 8 dots

300 DPI: 1mm = 12 dots
See Also
FEED, SIZE, GAP, HOME, FORMFEED

Downloaded from www.Manualslib.com manuals search engine

  FORM FEED

Description
This command feeds label to the beginning of next label.

Syntax
FORMFEED

Parameter Description
None N/A

Example
SIZE 4,2.5
GAP 0 mm,0
SPEED 4
DENSITY 7
DIRECTION 0
OFFSET 0.00
REFERENCE 0,0
SET PEEL OFF
SET COUNTER @0 +1
@0="000001"
FORMFEED
CLS
BOX 1,1,360,65,12
TEXT 25,25,"3",0,1,1,"FORMFEED COMMAND TEST"
TEXT 25,80,"3",0,1,1,@0
PRINT 3,1

See Also
FEED, SIZE, GAP, , HOME, BACKFEED

Downloaded from www.Manualslib.com manuals search engine

  HOME

Description
It is not expected the first label will be printed on the right position when the
printer power is turned on. This command will feed label to the beginning of
next label .The size and gap of the label should be setup in advance.

Syntax
HOME

Parameter Description
None N/A

Example
SIZE 4,2.5
GAP 2 mm,0
SPEED 4
DENSITY 7
DIRECTION 0
OFFSET 0.00
REFERENCE 0,0
SET PEEL OFF
SET COUNTER @0 +1
@0="000001"
HOME
CLS
BOX 1,1,360,65,12
TEXT 25,25,"3",0,1,1,"HOME COMMAND TEST"
TEXT 25,80,"3",0,1,1,@0
PRINT 3,1

See Also
FEED, SIZE, GAP, BLINE, FORMFEED

Downloaded from www.Manualslib.com manuals search engine

 PRINT

Description
This command prints the label format stored in the image buffer.

Syntax
PRINT m [,n]

Parameter Description
m Specifies how many sets of labels will be printed.
1 ≤ m ≤ 999999999

If m=-1, printer will print the last label content for n

copies.

n Specifies how many copies should be printed for

each set of label.
1 ≤ n ≤ 999999999

Example
SIZE 60 mm, 20 mm
SET COUNTER @1 1
@1=”0001”
CLS
TEXT 10,10,”3”,0,1,1,@1
PRINT 3,2
PRINT –1,2

See Also
SET COUNTER, INPUT, DOWNLOAD

Downloaded from www.Manualslib.com manuals search engine

 SOUND

Description
This command is used to control the sound frequency of the beeper. There
are 10 levels of sounds. The timing control the sound can be set by the
“interval” parameter.

Syntax
SOUND level,interval

Parameter Description
level Sound level: 0~9
interval Sound interval: 1~4095

Example
SOUND 5,200
SOUND 3,200
SOUND 3,200
SOUND 4,200
SOUND 2,200
SOUND 2,200
SOUND 1,200
SOUND 2,200
SOUND 3,200
SOUND 4,200
SOUND 5,200

Downloaded from www.Manualslib.com manuals search engine

 LIMITFEED

Description
When feeding labels, if the gap sensor is not set to a suitable sensitivity, the
printer will not be able to locate the correct position of the gap. This command
is used stop label feeding and make the red LED flash if the printer does not
locate gap after feeding the length of one label plus one preset value.

Syntax
LIMITFEED n (inch, the English system)
LIMITFEED n mm (mm, the metric system)

Parameter Description
n inch or mm

Remark
The setting will remain resident in memory.
The default value is 10 inches when printer initializes.
For metric system, there must be a space between parameter n and mm.

SELFTEST

Description
At this command, the printer will print out the printer information on the label.

Syntax
SELFTEST

Example
SELFTEST

Downloaded from www.Manualslib.com manuals search engine

 Label Formatting Commands

1. BAR

Description
This command is used to draw a line or a bar on the label format.

Syntax
BAR x, y, width, height

Parameter Description
x The upper left corner x-coordinate in dot
y The upper left corner y-coordinate in dot
width The width of bar in dot
height The height of bar in dot

Note: 203 DPI: 1 mm = 8 dots

300 DPI: 1 mm = 12 dots
Recommended max. bar height is 12mm at 3” width. Bar height
over than 12 mm may damage the power supply and affect the
print quality.
Max. print ratio is different for each printer model. Desktop and
industrial printer print ratio is limited to 20% and 30%
respectively.

Example
SIZE 4,2.5
GAP 0,0
SPEED 6
DENSITY 8
DIRECTION 0
CLS
BAR 100, 100, 300, 200
PRINT 1,1

See Also
BOX

Downloaded from www.Manualslib.com manuals search engine

 2. BARCODE
Description
This command is used to print 1D barcodes on label form.
The available bar codes are listed below:

 Code 128 (Automatically switch character set)

 Code 128M (Manually switch character set)
 EAN 128 (Automatically switch character set)
 Interleaved 2 of 5
 Interleaved 2 of 5 with check digit
 Code 39 standard
 Code 39 full ASCII
 Code 39 full ASCII with check digit
 Code 93
 EAN 13
 EAN 13 with 2 digits add-on
 EAN 13 with 5 digits add-on
 EAN 8
 EAN 8 with 2 digits add-on
 EAN 8 with 5 digits add-on
 Codabar
 Postnet
 UPC-A
 UPC-A with 2 digits add-on
 UPC-A with 5 digits add-on
 UPC-E
 UPC-E with 2 digits add-on
 UPC-E with 5 digits add-on
 MSI
 PLESSEY
 China POST
 ITF14
 EAN14
Syntax
BARCODE X, Y, ”code type”, height, human readable, rotation, narrow, wide,
“code”

Parameter Description
x Specify the x-coordinate of the bar code on label
y Specify the y-coordinate of the bar code on label
code type
128 Code 128, switching code subset A, B, C
automatically
128M Code 128, switching code subset A, B, C manually.

Downloaded from www.Manualslib.com manuals search engine

 Control code A B C
096 FNC3 FNC3 NONE
097 FNC2 FNC2 NONE
098 SHIFT SHIFT NONE
099 CODE C CODE C NONE
100 CODE B FNC4 CODE B
101 FNC4 CODE A CODE A
102 FNC1 FNC1 FNC1
103 Start (CODE A)
104 Start (CODE B)
105 Start (CODE C)

Use “!” as a starting character for the control code followed by three
control codes.
If the start subset is not set, the default starting subset is B.

 EAN128 Code 128, switching code subset A, B, C automatically

 25 Interleaved 2 of 5
 25C Interleaved 2 of 5 with check digits
 39 Auto switch full ASCII and standard code 39 for
PLUS models.
 39C Code 39 full ASCII with check digit
Code 39 standard with check digit
Auto switch full ASCII and standard code 39 for
PLUS models.
 39S Code 39 standard
 93 Code 93
 EAN 13 EAN 13
 EAN 13 + 2 EAN 13 with 2 digits add-on
 EAN 13 + 5 EAN 13 with 5 digits add-on
 EAN 8 EAN 8
 EAN 8 + 2 EAN 8 with 2 digits add-on
 EAN 8 + 5 EAN 8 with 5 digits add-on
 CODA Codabar
 POST Postnet
 UPCA UPC-A
 UPCA + 2 UPC-A with 2 digits add-on
 UPCA + 5 UPC-A with 5 digits add-on
 UPCE UPC-E
 UPCE + 2 UPC-E with 2 digits add-on
 UPCE + 5 UPC-E with 5 digits add-on
 CPOST China post code
 MSI MSI code
 MSIC
 PLESSEY PLESSEY code
 ITF 14 ITF 14 code
 EAN 14 EAN 14 code
 height bar code height expressed by dot
 human readable 0: human not readable
1: human readable

Downloaded from www.Manualslib.com manuals search engine

  rotation Rotate bar code clockwise in degrees
0 non rotation
90 rotate 90 degrees clockwise
180 rotate 180 degrees clockwise
270 rotate 270 degrees clockwise
narrow width of narrow element in dot
wide width of wide element in dot

narrow : wide narrow : wide narrow : wide narrow : wide narrow : wide
1：1 1：2 1：3 2：5 3：7
128 10x N/A N/A N/A N/A
EAN128 10x N/A N/A N/A N/A
25 N/A 10x 10x 5x N/A
25C N/A 10x 10x 5x N/A
39 N/A 10x 10x 5x N/A
39C N/A 10x 10x 5x N/A
93 N/A N/A 10x N/A N/A
EAN13 8x N/A N/A N/A N/A
EAN13+2 8x N/A N/A N/A N/A
EAN13+5 8x N/A N/A N/A N/A
EAN8 8x N/A N/A N/A N/A
EAN8+2 8x N/A N/A N/A N/A
EAN8+5 8x N/A N/A N/A N/A
CODA N/A 10x 10x 5x N/A
POST 1x N/A N/A N/A N/A
UPCA 8x N/A N/A N/A N/A
UPCA+2 8x N/A N/A N/A N/A
UPCA+5 8x N/A N/A N/A N/A
UPCE 8x N/A N/A N/A N/A
UPCE+2 8x N/A N/A N/A N/A
UPCE+5 8x N/A N/A N/A N/A
CPOST N/A N/A N/A N/A 1x
MSI N/A N/A 10x N/A N/A
MSIC N/A N/A 10x N/A N/A
PLESSY N/A N/A 10x N/A N/A
ITF14 N/A 10x 10x 5x N/A
EAN14 N/A N/A N/A 5x N/A

Downloaded from www.Manualslib.com manuals search engine

 Code number the maximum number of digits of bar code content

Barcode type Maximum bar Barcode type Maximum bar

Code length Code length
128 — POST 5,9,11
EAN128 — UPCA 11
_
25 — UPCA + 2 13
25
25C __ UPCA + 5 16
—
—
39 UPCE 6
39C — UPCE +2 8
93 — UPCE + 5 11
EAN13 12 CPOST _
EAN13+2 14 MSI _
EAN13+5 17 MSIC _
EAN8 7 PLESSY _
EAN8+2 9 ITF14 13
EAN8+5 12 EAN14 13
CODA _

Example

BARCODE 100,100,”39”,96,1,0,2,4,”1000”
BARCODE 10,10,”128M”,48,1,0,2,2,”!104!096ABCD!101EFGH”
(The above example of code 128M encoded with CODE B start character.
The next character will be the code 128 function character FNC3 which is
then followed by the ABCD characters and EFGH characters encoded as CODE A subset

Downloaded from www.Manualslib.com manuals search engine

 3. BITMAP

Description
This command is used to draw bitmap images (Not BMP graphic file).

Syntax
BITMAP X, Y, width, height, mode, bitmap data…
Parameter Description
x Specify the x-coordinate of the bitmap image
y Specify the y-coordinate of the bitmap image
width The width of the image in bytes
height The height of the image in dot
mode Graphic mode is listed below:
0 OVERWRITE
1 OR
2 XOR
bitmap data The bitmap data

Downloaded from www.Manualslib.com manuals search engine

 ROW L-Byte R-Byte
(Y- axis) Binary Hexadecimal Binary Hexadecimal
0 00000000 00 00000000 00
1 00000000 00 00000000 00
2 00000000 00 00000000 00
3 00000111 07 11111111 FF
4 00000011 03 11111111 FF
5 00010001 11 11111111 FF
6 00011000 18 11111111 FF
7 00011100 1C 01111111 7F
8 00011110 1E 00111111 3F
9 00011111 1F 00011111 1F
A 00011111 1F 10001111 8F
B 00011111 1F 11000111 C7
C 00011111 1F 11100011 E3
D 00011111 1F 11110111 F7
E 00011111 1F 11111111 FF
F 00011111 1F 11111111 FF

Example:
SIZE 4,2
GAP 0,0
CLS
BITMAP 200,200,2,16,0,     •-????? 
PRINT 1,1

Hexadecimal ASCII
53 49 5A 45 20 34 2C 32 0D 0A 47 41 50 20 SIZE 4,2
30 2C 30 0D 0A 43 4C 53 0D 0A 42 49 54 4D GAP 0,0
41 50 20 32 30 30 2C 32 30 30 2C 32 2C 31
36 2C 30 2C 00 00 00 00 00 00 07 FF 03 FF
11 FF 18 FF 1C 7F 1E 3F 1F 1F 1F 8F 1F C7 CLS
1F E3 1F E7 1F FF 1F FF 0D 0A 50 52 49 4E
54 20 31 2C 31 0D 0A
BITMAP 200,200,2,16,0
,    •-?-
???? 

PRINT 1,1

See Also
PUTBMP, PUTPCX

Downloaded from www.Manualslib.com manuals search engine

 4. BOX

Description
This command is used to draw rectangles on the label.

Syntax
BOX X_start, Y_start, X_end, Y_end, line thickness

Parameter Description
X_start Specify x-coordinate of upper left corner in dot
Y_start Specify y-coordinate of upper left corner in dot
X_end Specify x-coordinate of lower right corner in dot
Y_end Specify y-coordinate of lower right corner in dot
line thickness Line thickness of the box in dot

Note: 203 DPI: 1 mm = 8 dots

300 DPI: 1 mm = 12 dots

Recommended max. thickness of box is 12mm at 3” width.

Thickness of box that is larger than 12 mm may damage the power
supply and affect the print quality.
Max. print ratio is different for each printer model. Desktop and
industrial printer print ratio is limited to 20% and 30%
respectively.

Example
SIZE 4,2.5
GAP 0,0
SPEED 6
DENSITY 8
DIRECTION 0
CLS
BOX 100,100,200,200,5
PRINT 1,1

See Also
BAR

Downloaded from www.Manualslib.com manuals search engine

 5. ERASE

Description
This command is used to clear a specified region in image buffer.

Syntax
ERASE X_start, Y_start, X_width, Y_height

Parameter Description
X_start The x-coordinate of the starting point in dot
Y_start The y-coordinate of the starting point in dot
X_width The region width in x-axis direction in dot
Y_height The region height in y-axis direction in dot

Example
SIZE 4,2.5
GAP 0,0
SPEED 6
DENSITY 8
DIRECTION 0
CLS
BAR 100, 100, 300, 300
ERASE 150,150,200,200
PRINT 1,1

See Also
CLS

Downloaded from www.Manualslib.com manuals search engine

 6. PUTBMP

Description
This command is used to print BMP format image.

Syntax
PUTBMP X, Y, ”filename”

Parameter Description
x The x-coordinate of the BMP format image
y The y-coordinate of the BMP format image
filename The downloaded BMP filename.

Note: Suggest to use only black and white color BMP file.

Example

See Also

DOWNLOAD, BITMAP, PUTPCX

Downloaded from www.Manualslib.com manuals search engine

 7. PUTPCX

Description
This command is used to print PCX format image.

Syntax
PUTPCX X, Y, ”filename”

Parameter Description
x The x-coordinate of the PCX image
y The y-coordinate of the PCX image
filename The downloaded PCX filename. Case sensitive

Example

See Also
DOWNLOAD, BITMAP, PUTPCX

Downloaded from www.Manualslib.com manuals search engine

 8. QRCODE
Description:
This command prints QR code.

Syntax
QRCODE x,y,ECC Level,cell width,mode,rotation,[model,mask,]"content"

Parameter Description
x The upper left corner x-coordinate of the QR code
y The upper left corner y-coordinate of the QR code
ECC level Error correction recovery level
L : 7%
M : 15%
Q : 25%
H : 30%
cell width 1~10
mode Auto / manual encode
A : Auto
M : Manual
rotation 0 : 0 degree
90 : 90 degree
180 : 180 degree
270 : 270 degree
model 1: (default), original version
2: enhanced version
(Almost smart phone is supported by this version.)
mask 0~8, default is 7
content The encodable character set is described as below,
Encodable character set:
1) Numeric data: (digits 0~9)
2) Alphanumeric data
Digits 0-9
Upper case letters A-Z
Nine other characters: space, $ % * + - . / : )
3) 8-bit byte data
JIS 8-bit character set (Latin and Kana) in accordance
with JIS X 0201
4) Kanji characters
Shift JIS values 8140HEX –9FFCHEX and E040HEX –EAA4
HEX. These are values shifted from those of JIS X 0208.
Refer to JIS X 0208 Annex 1Shift Coded Representation
for detail.

Downloaded from www.Manualslib.com manuals search engine

 Data characters per symbol (for maximum symbol size):

Model 1 (Version 14-L) Model 2 (Version 40-L)

1). Numeric data： 1,167 characters 7,089 characters
2). Alphanumeric data： 707 characters 4,296 characters
3). 8-bit byte data： 486 characters 2,953 characters
4). Kanji data: 299 characters 1,817 characters

Manual mode

* If “A” is the first character in the data string, then the following data
after “A” is alphanumeric data.
* If “N” is the first character in the data string, then the following data
after “N” is numeric data.
*If “B” is the first character in the data string, then the following 4 digits
after “B” is used to specify numbers of data. After the 4 digits is the
number of bytes of binary data to be encoded.
*If “K” is the first character in the data string, then the following data
after “K” is Kanji data.
*If “!” is in the data string and follows by “N”, “A”, “B”, “K” then it will be
switched to specified encodable character set.

Manual mode example:

QRCODE 100,10,L,7,M,0,M1,S1,"ATHE FIRMWARE HAS BEEN UPDATED"

(Where A: Alphanumeric data)
QRCODE 100,10,M,7,M,0,M1,S2,"N123456"
(Where N: Numeric data)
QRCODE 100,10,Q,7,M,0,M1,S3,"N123456!ATHE FIRMWARE HAS BEEN
UPDATED"
(Where N: Numeric data ; !:Transfer char ; A: Alphanumeric data)
QRCODE 100,10,H,7,M,0,M1,S3,"B0012Product name"
(where B: Binary data ; 0012: 12 bytes )
QRCODE 100,10,M,7,M,0,M1,S3,"K"
(Where K: Kanji data)

Auto mode example:

QRCODE 100,10,M,7,A,0,"THE FIRMWARE HAS BEEN UPDATED"

Downloaded from www.Manualslib.com manuals search engine

 (1) Example of generating QRCODE in Auto mode:
a. General data string
SIZE 4,2.5
GAP 0.12,0
CLS
QRCODE 10,10,H,4,A,0,"ABCabc123"
QRCODE 160,160,H,4,A,0,"123ABCabc"
QRCODE 310,310,H,4,A,0,"打印机 ABCabc123"
PRINT 1,1
b. The string including <Enter>(i.e.: 0Dh, 0Ah)
SIZE 4,2.5
GAP 0.12,0
CLS
QRCODE 10,10,H,4,A,0,"ABC<Enter>
abc<Enter>
123"
QRCODE 160,160,H,4,A,0,"123<Enter>
ABC<Enter>
abc"
QRCODE 310,310,H,4,A,0,"打印机<Enter>
ABC<Enter>
abc<Enter>
123"
PRINT 1,1
c. Data concatenation (Must in DOENLOAD…EOP mode)
DOWNLOAD “DEMO.BAS”
SIZE 4,2.5
CAP 0.12,0
CLS
QRCODE 10,10,H,4,A,0,"ABCabc123"+STR$(1234)
QRCODE 160,160,H,4,A,0,"123ABCabc"+"1234"
QRCODE 310,310,H,4,A,0,"打印机 ABCabc123"+"1234"+"abcd"
PRINT 1,1
EOP
DEMO
d. Data including Double quotation mark, change (“) to \[“].
SIZE 4,2.5
CAP 0.12,0
CLS
QRCODE 10,10,H,4,A,0,"ABC\["]abc\["]123"
QRCODE 160,160,H,4,A,0,"123\["]ABC\["]abc"
QRCODE 310,310,H,4,A,0,"\["]打印机\["]ABCabc123"
PRINT 1,1

Downloaded from www.Manualslib.com manuals search engine

 (2) Example of generating QRCODE in Manual mode:
a. a. General data string
SIZE 4,2.5
CAP 0.12,0
CLS
QRCODE 10,10,H,4,M,0,"AABC!B0003abc!N123"
QRCODE 160,160,H,4,M,0,"N123!AABC!B0003abc"
QRCODE 310,310,H,4,M,0,"K 打印机!AABC!B0006abc123"
PRINT 1,1
b. The string including <Enter>(i.e.: 0Dh, 0Ah), <Enter> shall be 8-bit byte data
SIZE 4,2.5
CAP 0.12,0
CLS
QRCODE 10,10,H,4,M,0,"AABC!B0007<Enter>
abc<Enter>
!N123"
QRCODE 160,160,H,4,M,0,"N123!B0002<Enter>
!AABC!B0005<Enter>
abc"
QRCODE 310,310,H,4,M,0,"K 打印机!B0002<Enter>
!AABC!B0010<Enter>
abc<Enter>
123"
PRINT 1,1
c. Data concatenation (Must in DOENLOAD…EOP mode)
DOWNLOAD “A.BAS”
SIZE 4,2.5
CAP 0.12,0
CLS
QRCODE 10,10,H,4,M,0,"AABC!B0006abc123!N"+STR$(1234)
QRCODE 160,160,H,4,M,0,"N123!AABC!B0007abc"+"1234"
QRCODE 310,310,H,4,M,0,"K 打印机!AABC!B0014abc123"+"1234"+"abcd"
PRINT 1,1
EOP
A
d. Data including Double quotation mark, change (“) to \[“]
SIZE 4,2.5
CAP 0.12,0
CLS
QRCODE 10,10,H,4,M,0,"AABC!B0005\["]abc\["]!N123"
QRCODE 160,160,H,4,M,0,"N123!B0001\["]!AABC!B0004\["]abc"
QRCODE 310,310,H,4,M,0,"B0001\["]!K 打印机!B0010\["]ABCabc123"
PRINT 1,1

Downloaded from www.Manualslib.com manuals search engine

 9. REVERSE

Description
This command is used to reverse a region in image buffer.

Syntax
REVERSE X_start, Y_start, X_width, Y_height

Parameter Description
X_start The x-coordinate of the starting point in dot
Y_start The y-coordinate of the starting point in dot
X_width The region width in x-axis direction in dot
Y_height The region height in y-axis direction in dot

Note: 203 DPI: 1 mm = 8 dots

300 DPI: 1 mm = 12 dots

Recommended max. height of reversed black area is 12mm at 3”

width. Height of reversed area that is larger than 12 mm may
damage the power supply and affect the print quality.
Max. print ratio is different for each printer model. Desktop and
industrial printer print ratio is limited to 20% and 30%
respectively.

Example
SIZE 4,2.5
GAP 0,0
SPEED 6
DENSITY 8
DIRECTION 0
CLS
TEXT 100,100,"3",0,1,1,"REVERSE"
REVERSE 90,90,128,40
PRINT 1,

Downloaded from www.Manualslib.com manuals search engine

 10. TEXT

Description
This command is used to print text on label

Syntax
TEXT X, Y, ”font”, rotation, x-multiplication, y-multiplication, “content”

Parameter Description
X The x-coordinate of the text
Y The y-coordinate of the text
font Font name
1 8 x 12 fixed pitch dot font
2 12 x 20 fixed pitch dot font
3 16 x 24 fixed pitch dot font
4 24 x 32 fixed pitch dot font
5 32 x 48 dot fixed pitch font
6 14 x 19 dot fixed pitch font OCR-B
7 14 x25 dot fixed pitch font OCR-A
8 21 x 27 dot fixed pitch font OCR-B
TST24.BF2 Traditional Chinese 24 x 24 font(Big 5)
TSS24.BF2 Simplified Chinese 24 x 24 font (GB)
K Korean 24 x 24 font (KS)
Rotation The rotation angle of text
0 0 degree
90 90 degrees, in clockwise direction
180 180 degrees, in clockwise direction
270 270 degrees, in clockwise direction
X-multiplication: Horizontal multiplication, up to 10x.
Available factors: 1~10 width (point) of true type font.
1 point=1/72 inch.
Y-multiplication: Vertical multiplication, up to 10x.
Available factors: 1~10
For true type font, this parameter is used to specify
the height (point) of true type font.
1 point=1/72 inch.
Note:
1. If there is any double quote (“) within the text, please change it
to \[“].
2. If to print OD(hex), please use \[R] to print CR in the program.
3. If to print OA(hex), please use\[A] to print LF in the program.
4.Only use capital letters.

Downloaded from www.Manualslib.com manuals search engine

 Example 1.
SIZE 3,2
GAP 0,0
CLS
TEXT 100,100,"5",0,1,1,"\["]DEMO FOR TEXT\["]"
TEXT 100,200,"ROMAN.TTF",0,1,20,"\["]True Type Font Test Print\["]"
PRINT 1,1

Example 2：
DOWNLOAD F,"test.BAS"
SPEED 4
DENSITY 8
SET PEEL OFF
DIRECTION 0
SIZE 1.000,0.800
GAP 0.12,0.00
OFFSET 0.000
REFERENCE 0,0
:START
CLS
INPUT "Description",A$
Again:
F$=""
INPUT "Font:",1,F$
IF ASC(F$)>53 THEN GOTO Again
IF ASC(F$)<49 THEN GOTO Again
X_Again:
INPUT "X_multiple:",1,XM
IF XM>8 THEN GOTO X_Again
IF XM<1 THEN GOTO X_Again
Y_Again:
INPUT "Y_multiple:",1,YM
IF YM>8 THEN GOTO Y_Again
IF YM<1 THEN GOTO Y_Again

Z=LEN(A$)
WWidth=Z*XM*8
IF F$="1" THEN
REM *****When Font1, the space between every single word is XM*2 dots*****
WWidth=Z*(XM*8)
SWidth=Z*(XM*2)
X=101-((WWidth+SWidth)/2)
ELSEIF F$="2" THEN
REM *****When Font2, the space between every single word is XM*2 dots*****
WWidth=Z*(XM*12)
SWidth=Z*(XM*2)

Downloaded from www.Manualslib.com manuals search engine

 X=101-((WWidth+SWidth)/2)
ELSEIF F$="3" THEN
REM *****When Font3, the space between every single word is XM-1 dots*****
WWidth=Z*(XM*16)
SWidth=Z*(XM-1)
X=101-((WWidth+SWidth)/2)
ELSEIF F$="4" THEN
REM *****When Font4, the space between every single word is XM-1 dots*****
WWidth=Z*(XM*24)
SWidth=Z*(XM-1)
X=101-((WWidth+SWidth)/2)
ELSEIF F$="5" THEN
REM *****When Font5, the space between every single word is XM*4 dots*****
WWidth=Z*(XM*32)
SWidth=Z*(XM*4)
X=101-((WWidth+SWidth)/2)
ENDIF
TEXT X,116,F$,0,XM,YM,A$
PRINT 1,1
GOTO START
EOP

Downloaded from www.Manualslib.com manuals search engine

 Status Polling Commands (RS232)
<ESC>!?
Description
This command is used to obtain the printer status through serial port.
An inquiry request is solicited by sending an <ESC> [ASCII 27(Hex1B),
escape character] as the beginning control character to the printer.
It can be sent any time, even in the event of printer error. One byte
character is returned, of which one bit is used to flag the printer’s current
readiness status. If 0 is returned, the printer is ready to print labels.

Bit Status
0 Head opened
1 Paper jam
2 Out of paper
3 Out of ribbon
4 Pause
5 Printing
6 Cover opened (option)
7 Environment Temperature over range (option)

Syntax
<ESC>!?

See Also
<ESC>!R

<ESC>!R

Description
This command is used to reset the printer. It can be sent at any time as long
as the printer is powered on and not in the dump mode. The beginning of
the command is an ESCAPE character (ASCII 27) (Hex1B). The files downloaded in
DRAM will be deleted.

Syntax
<ESC>!R

Parameter Description
N/A N/A

See Also
<ESC>!?

Downloaded from www.Manualslib.com manuals search engine

 ~!@

Description
This command is used to inquire the mileage of the printer. The integer part
of mileage is returned (the decimal part of mileage is not returned). It is returned to
PC in ASCII characters. The ending character of mileage is 0x0D 0x0A.

Syntax
~!@

Parameter Description
N/A N/A

Example
~!@

~!A

Description
This command is used to inquire about the free memory (DRAM, FLASH) of the
printer. The number of bytes of free memory is returned in decimal digits, with 0x0D
0x0A as ending code.

Syntax
~!A

Parameter Description
N/A N/A

Example
~!A

See Also
FILES

Downloaded from www.Manualslib.com manuals search engine

 ~!C
Description
This command is used to check and return if RTC is installed or not.

Syntax
~!C

Parameter Description
0 RTC not installed
1 RTC installed

Example
~!C

~!D
Description
This command is used to enter DUMP mode.

Syntax
~!D

Parameter Description
None N/A

Example
~!D

~!F
Description
This command is used to inquire about files resident in the printer memory
and fonts installed in the memory module.
The filename is returned in ASCII characters. Each file name ends with
0x20. The ending character is 0x0D 0x1A.

Syntax
~!F

Parameter Description
None N/A

Example
~!F

See Also
FILES

Downloaded from www.Manualslib.com manuals search engine

 ~!I

Description
The command is used to inquire the code page setting of the printer.
The returned information through RS-232 is given in the following format:

8 bit: 437, 001

Regarding to the information returned by the printer, please refer to CODEPAGE command.

Syntax
~!I

Parameter Description
None N/A

Example
~!I

See Also
CODEPAGE

~!T

Description
This command is used to inquire the model name and number of the printer.
They are returned in ASCII characters.

Syntax
~!T

Parameter Description
None N/A

Example
~!T

See Also
~!I, ~!F

Downloaded from www.Manualslib.com manuals search engine

 File Management Commands
DOWNLOAD

Description
“DOWNLOAD” is a header of the file that is to be saved in the printer's
Memory(DRAM). The downloaded files can be divided to two categories: program file
and data file (including text data file, PCX graphic files and bitmap font file).

Syntax
1. Download a program file
DOWNLOAD [n,]“FILENAME.BAS”

Parameter Description
n Specify the memory which is used to save the
download files.

n is ignored Download files to DRAM only.

F: Download files to main board flash memory.

FILENAME.BAS The filename resident in printer memory.

Note:
(1). The filename is case sensitive.
(2). The extension of the program file must be “.BAS”
(3). If memory is not specified, all files will be downloaded to
DRAM.
No Battery is used to backup DRAM. The downloaded files
in DRAM will be lost in case turns off printer power.

Downloaded from www.Manualslib.com manuals search engine

 2. Download a data file
DOWNLOAD [n,]“FILENAME”, DATA SIZE, DATA CONTENT…where
Parameter Description
n Specify the memory location to save the
download files.
n is ignored Download files to DRAM only. If you would like to
save the files from DRAM to Flash memory
before turning off power, you can issue MOVE
command to printer to move the files from DRAM
to Flash memory.
F: Download files to main board flash memory.
E: Download files to expansion memory module.
FILENAME.BAS The filename resident in printer memory.
DATA SIZE The actual file size in number of bytes.

Note:
(1). For text data file, CR (carriage return) 0x0D and LF (Line
Feed) 0x0A are the separator of data.
(2). If memory is not specified, all files will be downloaded to DRAM.
No Battery is used to backup DRAM. The downloaded files
in DRAM will be lost in case turns off printer power.

Example

The program listed below will download to printer SDRAM.

DOWNLOAD “EXAMPLE.BAS”
SIZE 4,4
GAP 0,0
DENSITY 8
SPEED 6
DIRECTION 0
REFERENCE 0,0
SET PEEL OFF
CLS
TEXT 100,100,”3”,0,1,1,”EXAMPLE PROGRAM”
PRINT 1
EOP

Note: When writing a download program, “DOWNLOAD” header must

be placed in the beginning of file, and “EOP” must be placed at
the end of program.
To run the program, you can call the main filename without BAS
extension or use RUN command to start the download program.
Example:
1. Call the main filename
C:\>COPY CON LPT1<ENTER>
EXAMPLE<ENTER>
<CTRL><Z>
C:\>

Downloaded from www.Manualslib.com manuals search engine

 2. Use Run command to start the program
C:\>COPY CON LPT1<ENTER>
RUN “EXAMPLE.BAS”<ENTER>
<CTRL><Z>
C:\>

Below is an example of downloading data file.

DOWNLOAD “DATA”,20,COMPUTER<Enter>
2001<Enter>
21<Enter>

Note: <ENTER> stands for keyboard “ENTER” key. In the above

example, please press “ENTER” key instead of typing <ENTER>
in the above example.

See Also
EOP, RUN, PUTBMP, PUTPCX,

EOP

Description
End of program. To declare the start and end of BASIC language commands
used in a program, the DOWNLOAD “FILENAME.BAS” must be added in the
first line of the program, and “EOP” statement at the last line of program.

Syntax
EOP

Example
DOWNLOAD “DEMO.BAS”
SIZE 4,4
GAP 0,0
DENSITY 8
SPEED 6
DIRECTION 0
REFERENCE 0,0

SET PEEL OFF

CLS
TEXT 100,100,”3”,0,1,1,”DEMO PROGRAM”
PRINT 1
EOP

See Also
DOWNLOAD, EOP,

Downloaded from www.Manualslib.com manuals search engine

 FILES

Description
This command prints out the filenames (or lists the files through RS-232)
that remained in the printer memory (both FLASH memory and DRAM). The
total memory size and available memory size are printed out or lists as well.

Syntax
FILES

Example
Follow the steps below to print out (or lists the files through RS-232) the files
that are saved in printer memory in DOS environment through serial port or
parallel port connection.

C:\>MODE COM1 96,N,8,1<ENTER>

C:\>COPY CON COM1<ENTER>
FILES<ENTER>
<CTRL><Z><ENTER>
C:\>

Or

C:\>COPY CON LPT1<ENTER>

FILES<ENTER>
<CTRL><Z><ENTER>

Note: <ENTER> stands for PC keyboard “ENTER” key.

<CTRL><Z> means to hold PC keyboard “CTRL” key then press
the PC keyboard <Z> key.

See Also
~!F, KILL

Downloaded from www.Manualslib.com manuals search engine

 KILL

Description
This command deletes a file in the printer memory. The wild card (*) will
delete all files resident in specified DRAM or FLASH memory.

Syntax
KILL [n],”FILENAME”

Parameter Description
n Specify the memory location that files will be deleted.
n is ignored Kill files saved in DRAM.
F: Kill files from main board flash memory.

Note:
(1). If optional parameter n is not specified, firmware will delete the file in
DRAM.

Syntax example
1. KILL “FILENAME”
2. KILL “*.PCX”
3. KILL “*”
4. KILL F,“FILENAME”
5. KILL E,“*.PCX”

Example
Users can use printer SELFTEST utility to list printer configurations and files
saved in the printer memory, or use the FILES command to print the
downloaded file list in printer. Follow the steps below to delete files in the
printer memory via parallel port connection.
C:\>COPY CON LPT1<ENTER>
FILES<ENTER>
<CTRL><Z><ENTER>
C:\>COPY CON LPT1<ENTER>
KILL “DEMO.BAS” <ENTER>
<CTRL><Z><ENTER>
C:\>COPY CON LPT1<ENTER>
FILES<ENTER>
<CTRL><Z><ENTER>

Note: <ENTER> stands for PC keyboard “ENTER” key.

<CTRL><Z> means to hold PC keyboard “CTRL” key then press
the PC keyboard <Z> key

See Also
~!F, FILES

Downloaded from www.Manualslib.com manuals search engine

 MOVE

Description
This command is used to move downloaded files from DRAM to the FLASH
memory.

Syntax
MOVE

Parameter Description
N/A N/A

See Also
DOWNLOAD, EOP

RUN

Description
This command is used to execute a program that resident in printer memory

Syntax
RUN “FILENAME.BAS”

Example
C:\>COPY CON LPT1<ENTER>
RUN “DEMO.BAS”<ENTER>
<CTRL><Z><ENTER>
C:\>

Note: <ENTER> stands for PC keyboard “ENTER” key.

<CTRL><Z> means to hold PC keyboard “CTRL” key then press
the PC keyboard <Z> key
See Also
DOWNLOAD, EOP

Downloaded from www.Manualslib.com manuals search engine

 BASIC Commands and Functions
ABS( )

Description
This function returns the absolute value of an integer, floating point or variable.

Syntax
ABS (-100)
ABS (-99.99)
ABS (VARIABLE)

Example
DOWNLOAD “TEST.BAS”
SIZE 4,4
GAP 0,0
DENSITY 8
SPEED 3
DIRECTION 0
REFERENCE 0,0

SET PEEL OFF

CLS
A=ABS(-100)
B=ABS(-50.98)
C=-99.99
TEXT 100,100,”3”,0,1,1,STR$(A)
TEXT 100,150,”3”,0,1,1,STR$(B)
TEXT 100,200,”3”,0,1,1,STR$(ABS(C))
PRINT 1
EOP

See Also
DOWNLOAD, EOP

Downloaded from www.Manualslib.com manuals search engine

 ASC( )

Description
This function returns the ASCII code of the character.

Syntax
ASC (“A”)

Example
DOWNLOAD “TEST.BAS”
SIZE 3,4
GAP 0,0
DENSITY 8
SPEED 3
DIRECTION 0
REFERENCE 0,0

SET PEEL OFF

CLS
CODE1=ASC(“A”)
TEXT 100,100,”3”,0,1,1,STR$(CODE1)
PRINT 1
EOP

See Also
DOWNLOAD, EOP, STR$()

Downloaded from www.Manualslib.com manuals search engine

 CHR$( )

Description
This function returns the character that has the specified ASCII code.

Syntax
CHR$(n)

Parameter Description
n The ASCII code

Example
DOWNLOAD “TEST.BAS”
SIZE 3,4
GAP 0,0
DENSITY 8
SPEED 3
DIRECTION 0
REFERENCE 0,0

SET PEEL OFF

CLS
A=65
WORD$=CHR$(A)
TEXT 100,100,”3”,0,1,1,WORD$
PRINT 1
EOP

See Also
DOWNLOAD, EOP, STR$(), ASC$()

Downloaded from www.Manualslib.com manuals search engine

 END

Description
This command states the ending of program.

Syntax
END

Example
DOWNLOAD "DEMO.BAS"
SIZE 3,2
GAP 0,0
DENSITY 8
SPEED 6
DIRECTION 0
REFERENCE 0,0

SET PEEL OFF

CLS
TEXT 200,60,"4",0,1,1,"END COMMAND TEST"
X=300
Y=200
X1=500
Y1=400
GOSUB DR_LINE
PRINT 1
END

:DR_LINE
FOR I=1 TO 100 STEP 10
BOX X+I,Y+I,X1-I,Y1-I,5
NEXT
RETURN
EOP
DEMO

See Also
DOWNLOAD, EOP

Downloaded from www.Manualslib.com manuals search engine

 EOF( )

Description
This function is used to detect an opened download file to see whether it has
reached the end of file.

Syntax
EOF (File Handle)

Parameter Description
File handle Either 0 or 1

Parameter Description
None-zero End of file
0 Not end of file

Example
DOWNLOAD "DATA",16,COMPUTER
2000

DOWNLOAD "DEMO.BAS"
SIZE 3,3
GAP 0.0,0
DENSITY 8
SPEED 4
DIRECTION 0
REFERENCE 0,0
SET PEEL OFF
CLS
OPEN "DATA",0
SEEK 0,0
Y=110
TEXT 10,10,"3",0,1,1,"*****EOF TEST*****"
:A
Temp$=""
READ 0,ITEM$,P
TEXT 10,Y,"2",0,1,1,ITEM$+"$"+STR$(P)+"[EOF(0)="+STR$(EOF(0))+"]"
BARCODE 10,Y+25,"39",40,1,0,2,4,"PRICE-"+STR$(P)
Y=Y+100
IF EOF(0)=0 THEN GOTO A
PRINT 1
EOP
DEMO

See Also
DOWNLOAD, EOP, OPEN, READ, SEEK

Downloaded from www.Manualslib.com manuals search engine

 OPEN

Description
This command is used to open a downloaded file and establish the file
handle. Up to 2 files can be opened at the same time. The file to be opened
should be downloaded prior to using this command.

Syntax
OPEN “Filename”, File handle

Parameter Description
Filename The file downloaded in the printer memory
File handle Either 0 or 1.

Example
If a file by the name of “DATA” is to be downloaded,
The file format contains:

DOWNLOAD "DATA1",56,COMPUTER
2000
12
MOUSE
500
13
KEYBOARD
300
100

DOWNLOAD "DATA2",56,Computer
3000
32
Mouse
900
93
Keyboard
700
700

Saving the above contents of data under the file name of “DATA”. Follow the
steps below to download data to the printer

C:\>COPY DATA/B LPT1

If a file by name of “DEMO.BAS is to be downloaded, the file format

contains:
DOWNLOAD "DEMO.BAS"
SIZE 3,1
GAP 0,0

Downloaded from www.Manualslib.com manuals search engine

 DENSITY 8
SPEED 4
DIRECTION 0
REFERENCE 0,0
SET PEEL OFF
I=1
Y=100
GOSUB OpenData
:Start
CLS
TEXT 10,10,"3",0,1,1,"*****OPEN COMMAND TEST*****"
ITEM$=""
READ 0,ITEM$,P,Q
TEXT 10,Y,"2",0,1,1,ITEM$+"$"+STR$(P)+"[EOF(0)="+STR$(EOF(0))+"]"
BARCODE 10,Y+25,"39",40,1,0,2,4,"PRICE*"+STR$(Q)+"="+STR$(P*Q)
Y=Y+100
PRINT 1
Y=100
IF EOF(0)=1 THEN GOSUB OpenData
IF EOF(0)=0 THEN GOTO Start
END
:OpenData
IF I=1 THEN OPEN "DATA1",0
IF I=2 THEN OPEN "DATA2",0
SEEK 0,0
IF I>2 THEN END
I=I+1
RETURN
EOP
DEMO
Saving the above contents of data under the file name of “DEMO”.
Follow the steps below to download data to the printer
<under MS-DOS mode>:
C:\>COPY DEMO/B LPT1
Execute DEMO.BAS in printer:
C:\>COPY CON LPT1
DEMO
<Ctrl><Z>
The above example instructs the printer to open the file “DATA1” and
“DATA2” with same file handle of 0, and read items from the file.

See Also
DOWNLOAD, EOP, READ, EOF, LOF, SEEK, FREAD$()

Downloaded from www.Manualslib.com manuals search engine

 READ

Description
This command is used to read data from downloaded data file

Syntax
READ file handle, variables

Parameter Description
File handle 0 or 1.
variables string, integer or float point variable

Example

DOWNLOAD "DATA1",20,COMPUTER
2000
12

DOWNLOAD "DATA2",16,Mouse
900
93

DOWNLOAD "DEMO.BAS"
SIZE 3,1
GAP 0,0
DENSITY 8
SPEED 4
DIRECTION 0
REFERENCE 0,0
SET PEEL OFF
I=0
Y=100
OPEN "DATA1",0
OPEN "DATA2",1
SEEK 0,0
SEEK 1,0
:Start
CLS
TEXT 10,10,"3",0,1,1,"*****READ COMMAND TEST*****"
TEXT 10,50,"3",0,1,1,"OPEN-READ DATA"+STR$(I+1)
ITEM$=""
READ I,ITEM$,P,Q
TEXT 10,Y,"2",0,1,1,ITEM$+"$"+STR$(P)
BARCODE 10,Y+25,"39",40,1,0,2,4,"PRICE*"+STR$(Q)+"="+STR$(P*Q)
Y=Y+100
PRINT 1

Downloaded from www.Manualslib.com manuals search engine

 Y=100
IF I<=1 THEN
IF EOF(I)=1 THEN
I=I+1
GOTO Start
ELSE
GOTO Start
ENDIF
ELSE
END
ENDIF
EOP
DEMO

See Also
DOWNLOAD, EOP, OPEN, EOF, LOF, SEEK, FREAD$()

SEEK

Description
This command is used to shift the specified file pointer to a certain position.

Syntax
SEEK file handle, offset

Parameter Description
File handle 0 or 1.
offset the offset characters which are shifted to the
beginning of a new position

Downloaded from www.Manualslib.com manuals search engine

 Example
DOWNLOAD "DATA",12,1234567890

DOWNLOAD "TEST.BAS"
SIZE 3,1
GAP 0,0
DENSITY 8
SPEED 3
DIRECTION 1
REFERENCE 0,0
CLS
OPEN "DATA",0
SEEK 0,4
READ 0,Num$
TEXT 100,10,"3",0,1,1,"SEEK COMMAND TEST"
BAR 100,40,300,4
TEXT 100,60,"3",0,1,1,"SHIFT 4 CHARACTERS"
TEXT 100,110,"3",0,1,1,Num$
BAR 100,140,300,4
SEEK 0,0
READ 0,Num$
TEXT 100,160,"3",0,1,1,"SHIFT 0 CHARACTERS"
TEXT 100,210,"3",0,1,1,Num$
PRINT 1
EOP
TEST

See Also
DOWNLOAD, EOP, OPEN, READ, EOF, LOF, FREAD$()

Downloaded from www.Manualslib.com manuals search engine

 LOF( )

Description
This function returns the size of the specified file.

Syntax
LOF (“FILENAME”)

Parameter Description
FILENAME The file downloaded in the printer memory.

Example
DOWNLOAD "DATA1",10,1234567890

DOWNLOAD "DATA2",15,ABCDEFGHIJKLMNO

DOWNLOAD "LofTest.BAS"
SIZE 3,3
GAP 0.08,0
DENSITY 8
SPEED 3
DIRECTION 0
REFERENCE 0,0

SET PEEL OFF

CLS
OPEN "DATA1",0
OPEN "DATA2",1
TEXT 10,20,"4",0,1,1,"LOF() FUNCTION TEST"
J=LOF("DATA1")
K=LOF("DATA2")

TEXT 10,140,"3",0,1,1,"DATA1 IS: "+STR$(J)+" Bytes"

TEXT 10,200,"3",0,1,1,"DATA2 IS: "+STR$(K)+" Bytes"
PRINT 1
EOP
LofTest

See Also
DOWNLOAD, EOP, OPEN, READ, EOF, SEEK, FREAD$()

Downloaded from www.Manualslib.com manuals search engine

 FREAD$( )

Description
This function reads a specified number of bytes of data from a file.

Syntax
FREAD$ (file handle, byte)
Parameter Description
file handle Either 0 or 1
byte Number of bytes to be read

Example
DOWNLOAD "DATA1",10,1234567890
DOWNLOAD "DATA2",15,ABCDEFGHIJKLMNO
DOWNLOAD "OPEN2.BAS"
SIZE 3,3
GAP 0.08,0
DENSITY 8
SPEED 3
DIRECTION 0
REFERENCE 0,0
SET PEEL OFF
CLS
Y$=""
Z$=""
OPEN "DATA1",0
OPEN "DATA2",1
SEEK 0,0
SEEK 1,0
TEXT 10,260,"3",0,1,1,"FREAD$(0,6) IS: "+Y$
TEXT 10,320,"3",0,1,1,"FREAD$(1,6) IS: "+Z$
PRINT 1
EOP

See Also
DOWNLOAD, EOP, OPEN, READ, EOF, LOF(), SEEK

Downloaded from www.Manualslib.com manuals search engine

 FOR…NEXT LOOP

Description
Loop is used to execute one or more lines of program repetitively. Before anything,
a value should be assigned the loop counter to specify the execution times. Nested
loop is allowed (up to 39 nested loops) in this printer. Jumping out in the middle of
the FOR…NEXT loop is prohibited because it is not a good programming skill .

Syntax
For variable = start TO end STEP increment
statement; start < end
NEXT

Parameter Description
variable The variable name is up to 8 characters
start Can be integer or floating point numbers
end Can be integer of floating point numbers
increment nteger or floating point, positive or negative.

Example
DOWNLOAD "LOOP.BAS"
SIZE 3,3
GAP 0.08,0
DENSITY 8
SPEED 4
DIRECTION 1
CLS
FOR I=1 TO 10 STEP 1
TEXT 100,10+30*(I-1),"3",0,1,1,STR$(I)
NEXT
FOR I=1 TO 1000 STEP 100
TEXT 200,10+((I-1)/10)*3,"3",0,1,1,STR$(I)
NEXT
FOR I=110 TO 10 STEP -10
TEXT 300,10+(ABS(I-110))*3,"3",0,1,1,STR$(I)
NEXT
FOR I=1 TO 5 STEP 0.5
IF I-INT(I)=0 THEN Y=10+60*(I-1) ELSE Y=Y+30
TEXT 400,Y,"3",0,1,1,STR$(I)
NEXT
PRINT 1
EOP
LOOP

See Also
DOWNLOAD, EOP

Downloaded from www.Manualslib.com manuals search engine

 IF…THEN…ELSE…ENDIF

Description
Use IF…THEN block to execute one or more statements conditionally.
You can use either a single-line syntax or multiple-line “block” syntax:

Syntax
IF condition THEN statement

Notice: the single-line form of IF …THEN does not use an ENDIF

statement.

Or

IF condition THEN
Statements
ENDIF

Or

IF condition THEN
Statements
ELSE
Statements
ENDIF

Or

IF condition 1 THEN
Statement block 1
ELSEIF condition 2 THEN
Statement block 2
．．．
ELSEIF condition n THEN
Statement block n
ENDIF

The syntax of IF…THEN…ELSE requires that the command be typed in

one single line in less than 255 characters.

Parameter Description
condition Available relational operator: <, >, =, <=, >=
statement Only one statement is available in

Example

DOWNLOAD "DEMO.BAS"

Downloaded from www.Manualslib.com manuals search engine

 SIZE 3,3
GAP 0.12,0
SPEED 4
DENSITY 8
DIRECTION 1
REFERENCE 0,0
OFFSET 0.00

SET PEEL OFF

CLS
A=0
B=0
C=0
D=0
E=0
F=0
G=0
H=0
J=0
K=0
L=0
FOR I=1 TO 100
IF I-INT(I/1)*1=0 THEN A=A+I
IF I-INT(I/2)*2=1 THEN B=B+I ELSE C=C+I
IF I-INT(I/3)*3=0 THEN
D=D+I
ENDIF
IF I-INT(I/5)*5=0 THEN
E=E+I
ELSE
F=F+I
ENDIF
IF I-INT(I/7)*7=0 THEN
G=G+I
ELSEIF I-INT(I/17)*17=0 THEN
H=H+I
ELSEIF I-INT(I/27)*27=0 THEN
J=J+I
ELSEIF I-INT(I/37)*37=0 THEN
K=K+I
ELSE
L=L+I
ENDIF
NEXT
TEXT 100,110,"3",0,1,1,"(1) 1+2+3+...+100="+STR$(A)
TEXT 100,160,"3",0,1,1,"(2) 1+3+5+...+99="+STR$(B)
TEXT 100,210,"3",0,1,1,"(3) 2+4+6+...+100="+STR$(C)
TEXT 100,260,"3",0,1,1,"(4) 3+6+9+...+99="+STR$(D)
TEXT 100,310,"3",0,1,1,"(5) 5+10+15+...+100="+STR$(E)
TEXT 100,360,"3",0,1,1," (1)-(5)="+STR$(F)
TEXT 100,410,"3",0,1,1,"(6) 7+14+21+...+98="+STR$(G)
TEXT 100,460,"3",0,1,1,"(7) 17+34+51+...+85="+STR$(H)

Downloaded from www.Manualslib.com manuals search engine

 TEXT 100,510,"3",0,1,1,"(8) 27+54+...+81="+STR$(J)
TEXT 100,560,"3",0,1,1,"(9) 37+74="+STR$(K)
TEXT 100,610,"3",0,1,1," (1)-(6)-(7)-(8)-(9)="+STR$(L)
PRINT 1,1
EOP

DOWNLOAD “IFTHEN.BAS”
SIZE 3,4
GAP 0,0
DENSITY 8
SPEED 3
DIRECTION 0
REFERENCE 0,0

SET PEEL OFF

CLS
A=50
B=5
C$=""
D$=""

:L1
IF A>100 THEN GOTO L1 ELSE A=A+10
C$=STR$(A)+" IS SMALLER THAN 100"
TEXT 100,10,"4",0,1,1,C$
PRINT 1
END

:L2
A=A+B
D$=STR$(A)+" IS LARGER THAN 100"
TEXT 100,100,"4",0,1,1,D$
PRINT 1
GOTO L1
EOP

Note：
If the result of the expression is nonzero, the statement following
THEN will be executed. If the result of the expression is zero, and the
statement following the ELSE present, it will be executed. Otherwise
the next line of statement is executed.
If there are block of statements in IF…THEN …ELSE, ENDIF must be
used at the end of the IF…THEN …ELSE statement.
Limitations:
The total numbers of nested IF …THEN …ELSE statement in a
program can not exceed than 40.
The total numbers of nested IF …THEN …ELSE, FOR…NEXT, GOSUB
RETURN in a program can not exceed than 40 loops.

See Also
DOWNLOAD, EOP

Downloaded from www.Manualslib.com manuals search engine

 GOSUB…RETURN

Description
Branch to and return from a subroutine. Branch to the specified label and
execute subroutines until “RETURN” is reached and then go back to the
statement following the GOSUB statement.

Syntax
GOSUB LABEL
statement
END
:LABEL
statement
RETURN

Parameter Description
LABEL Beginning of the subroutine. The maximum
length of the label is 8 characters.

Example
DOWNLOAD "GOSUB1.BAS"
SIZE 3,3
GAP 0,0
DENSITY 8
SPEED 4
DIRECTION 0
CLS
TEXT 10,10,"3",0,1,1,"GOSUB & RETURN COMMAND TEST"
GOSUB DR_BOX
PRINT 1
END
:DR_BOX
FOR I=21 TO 81 STEP 10
BOX 80+I,80+I,80+300-I,80+300-I,5
NEXT
RETURN
EOP
GOSUB1

See Also
DOWNLOAD, EOP, END, GOTO

Downloaded from www.Manualslib.com manuals search engine

 GOTO

Description
This command is used to branch to a specified label. The label cannot
exceed 8 characters in length.

Syntax
GOTO LABEL

:LABEL
Parameter Description
None N/A

Example

DOWNLOAD "GOTO1.BAS"
SIZE 3,3
GAP 0.08,0
DENSITY 8
SPEED 4
DIRECTION 1
REFERENCE 0,0

SET PEEL OFF

CLS
A=0
TOTAL=0
:START
IF A<100 THEN
GOTO SUM
ELSE
GOTO PRTOUT
ENDIF
:SUM
A=A+1
TOTAL=TOTAL+A
GOTO START
:PRTOUT
B$="THE SUMMATION OF 1..100 IS "+STR$(TOTAL)
TEXT 10,100,"3",0,1,1,B$
PRINT 1
END
EOP

See Also
DOWNLOAD, EOP, END, GOSUB…RETURN

Downloaded from www.Manualslib.com manuals search engine

 REM

Description
Comment. Prefix is “REM” that will be ignored by the printer.

Syntax
REM

Example
REM ********************************
REM This is a demonstration program*
REM ********************************
DOWNLOAD "REMARK.BAS"
SIZE 3,3
GAP 0.08,0
DENSITY 8
SPEED 4
DIRECTION 1
REFERENCE 0,0

SET PEEL OFF

CLS
TEXT 50,50,"3",0,1,1,"REMARK DEMO PROGRAM"
REM TEXT 50,100,"3",0,1,1,"REMARK DEMO PROGRAM"
PRINT 1,1
EOP

See Also
DOWNLOAD, EOP, END

Downloaded from www.Manualslib.com manuals search engine

 INT( )

Description
This function is used to truncate a floating point number.

Syntax
INT (n)
Parameter Description
n n can be positive or negative integer, floating
point number or mathematical expression.

Example
DOWNLOAD "DEMO.BAS"
SIZE 3,2
GAP 0,0
DENSITY 8
SPEED 3
DIRECTION 0
REFERENCE 0,0

SET PEEL OFF

CLS
REM **** To round up or down****
INPUT "Number:",Num
N=INT(Num+0.5)
IF N>Num THEN
TEXT 50,100,"3",0,1,1,"To round up= "+STR$(N)
ELSE
TEXT 50,100,"3",0,1,1,"To round down= "+STR$(N)
ENDIF
PRINT 1
EOP

See Also
DOWNLOAD, EOP, END, ABS(), ASC(), STR$()

Downloaded from www.Manualslib.com manuals search engine

 LEFT$( )

Description
This function returns the specified number of characters down from the initial
character of a string.

Syntax
LEFT$ (X$, n)

Parameter Description
X$ The string to be processed
n The number of characters to be returned

Example
DOWNLOAD "STR1.BAS"
SIZE 3.00,3.00
GAP 0.08,0.00
SPEED 4.0
DENSITY 8

DIRECTION 0
REFERENCE 0,0
CLS
A$="BARCODE PRINTER DEMO PRINTING"
C$=LEFT$(A$,10)
TEXT 10,10,"3",0,1,1,A$
TEXT 10,100,"3",0,1,1,"10 LEFT 10 CHARS: "+C$
PRINT 1
EOP

See Also
DOWNLOAD, EOP, END, RIGHT$(), MID$(), LEN(), STR$()

Downloaded from www.Manualslib.com manuals search engine

 LEN( )

Description
This function returns the length of a string.

Syntax
LEN (string)

Parameter Description
string The string whose length is to be measured.

Example
DOWNLOAD "DEMO.BAS"
SIZE 3.00,3.00
GAP 0.08,0.00
SPEED 4.0
DENSITY 8

DIRECTION 0
REFERENCE 0,0
CLS
A$="TAIWAN SEMICONDUCTOR CO., LTD"
B=LEN(A$)
TEXT 10,10,"3",0,1,1,A$
TEXT 10,50,"3",0,1,1,"STRING LENGTH="+STR$(B)
PRINT 1
EOP

See Also
DOWNLOAD, EOP, END, LEFT$(), LEN(), RIGHT$(), MID$(), STR$(),
VAL()

Downloaded from www.Manualslib.com manuals search engine

 MID$( )

Description
This function is used to get the specified number of characters down from
the mth character of a string.

Syntax
MID$(string, m, n)

Parameter Description
string The string to be processed.
m The beginning of mth characters in the string.
1 <= m <= string length
n The number of characters to return.

Example
DOWNLOAD "DEMO.BAS"
SIZE 3.00,3.00
GAP 0.08,0.00
SPEED 4.0
DENSITY 8

DIRECTION 0
REFERENCE 0,0

CLS
A$="TAIWAN SEMICONDUCTOR CO., LTD"
E$=MID$(A$,11,10)
TEXT 10,10,"3",0,1,1,A$
TEXT 10,200,"3",0,1,1,"10 MIDDLE CHARS: "+E$
PRINT 1
EOP

See Also
DOWNLOAD, EOP, END, LEFT$(), LEN(), RIGHT$(), STR$(), VAL()

Downloaded from www.Manualslib.com manuals search engine

 RIGHT$( )

Description
This function returns the specified number of characters up from the end of
a string.

Syntax
RIGHT$ (X$, n)

Parameter Description
X$ The string to be processed
n The number of characters to be returned from the
right side (end) of the string

Example
DOWNLOAD "DEMO.BAS"
SIZE 3.00,3.00
GAP 0.08,0.00
SPEED 4.0
DENSITY 8

DIRECTION 0
REFERENCE 0,0

CLS
A$="TAIWAN SEMICONDUCTOR CO., LTD"
D$=RIGHT$(A$,10)
TEXT 10,10,"3",0,1,1,A$
TEXT 10,150,"3",0,1,1,"10 RIGHT CHARS: "+D$
PRINT 1
EOP

See Also
DOWNLOAD, EOP, END, LEFT$(), LEN(), MID$(), STR$(), VAL()

Downloaded from www.Manualslib.com manuals search engine

 STR$( )

Description
This function converts a specified value or expression into corresponding
string of characters.

Syntax
STR$ (n)

Parameter Description
n An integer, floating point number or mathematical
expression

Example
DOWNLOAD "DEMO.BAS"
SIZE 3.00,3.00
GAP 0,0.00
SPEED 4.0
DENSITY 8
DIRECTION 0
REFERENCE 0,0
CLS
A$="TAIWAN SEMICONDUCTOR CO., LTD"
F=100
G=500
H$=STR$(F+G)
TEXT 10,10,"3",0,1,1,A$
TEXT 10,60,"3",0,1,1,"F="+STR$(F)
TEXT 10,110,"3",0,1,1,"G="+STR$(G)
TEXT 10,160,"3",0,1,1,"F+G="+H$
PRINT 1
EOP
DEMO

See Also
DOWNLOAD, EOP, END, LEFT$(), LEN(), RIGHT$(), MID$(), VAL()

Downloaded from www.Manualslib.com manuals search engine

 VAL( )

Description
This function is used to convert numeric character into corresponding
integer or floating point number.

Syntax
VAL (“numeric character”)
Parameter Description
numeric character “0~9”, “.”

Example
DOWNLOAD "DEMO.BAS"
SIZE 3.00,3.00
GAP 0.00,0.00
SPEED 4.0
DENSITY 8
DIRECTION 0
REFERENCE 0,0
CLS
A$="TAIWAN SEMICONDUCTOR CO., LTD"
F$="100"
G$="500"
H=VAL(F$)+VAL(G$)
I$=STR$(H)
TEXT 10,10,"3",0,1,1,A$
TEXT 10,60,"3",0,1,1,"F="+F$
TEXT 10,110,"3",0,1,1,"G="+G$
TEXT 10,160,"3",0,1,1,"F+G="+I$
PRINT 1
EOP
DEMO

See Also
DOWNLOAD, EOP, END, LEFT$(), LEN(), RIGHT$(), MID$(), STR$()

Downloaded from www.Manualslib.com manuals search engine

 BEEP

Description
This command is used to issue a beep sound on portable keyboard.

Syntax
BEEP

Parameter Description
None N/A

Example
DOWNLOAD “DEMO.BAS”
SIZE 3,4
GAP 0,0
DENSITY 8
SPEED 6
DIRECTION 0
REFERENCE 0,0
SET PEEL OFF
CLS
BEEP
INPUT “Text1 =”,TEXT1$
TEXT 100,100,”3”,0,1,1,TEXT1$
PRINT 1
EOP

Downloaded from www.Manualslib.com manuals search engine

 Device Reconfiguration Commands
SET COUNTER

Description
Counter can be a real counter or a variable.
This setting sets the counter number in program and their increments.
There are three different kind of counters: digit (0~9~0), lower case letter
(a~z~a) and upper case letter (A~Z~A).

Syntax
SET COUNTER @n step
@n = “Expression”

Parameter Description
@n n: counter number. There are 51 counters available
(@0~@50) in the printer.
step The increment of the counter, can be positive or
negative.
-999999999<= step <=999999999
If the counter is used as a fixed variable, please set
the increment to 0.

Expression Initial string. String length is 101 bytes

Example
SIZE 3,3
GAP 0,0
DENSITY 8
SPEED 6
DIRECTION 0
REFERENCE 0,0
SET COUNTER @1 1
@1="00001"
SET COUNTER @2 5
@2="AB000001"
CLS
TEXT 50,50,"3",0,1,1,@1
BARCODE 50,100,"39",48,1,0,2,4,@2
PRINT 2,1

See Also
PRINT, TEXT, BARCODE

Downloaded from www.Manualslib.com manuals search engine

 SET KEY1, SET KEY2

Description
This setting is used to enable/disable the KEY1/KEY2 function. The default
function of KEY1 is “FEED” key, KEY2 is “PAUSE” key .Before setting KEY1
/KEY2 function otherwise, please disable KEY1/KEY2 first. The setting will remain
resident in the printer even when the printer is power off.

Syntax
SET KEY1 ON/OFF
SET KEY2 ON/OFF

Parameter Description
ON Enable KEY1 as FEED function
Enable KEY2 as PAUSE function
OFF Disable KEY1 as FEED function
Disable KEY2 as PAUSE function

Note: The setting will remain in the printer even if the printer is power
off.

Example
DOWNLOAD “DEMO.BAS”
SIZE 3,1
GAP 0,0
DENSITY 8
SPEED 3
DIRECTION 0
REFERENCE 0,0

SET KEY1 OFF

SET KEY2 OFF
KEY1=0
KEY2=0

CLS
:START
IF KEY1=1 THEN
CLS
TEXT 100,10,”3”,0,1,1,”KEY1 (FEED key) is pressed!!”
PRINT 1,1
ELSEIF KEY2=1 THEN
CLS
TEXT 100,10,”3”,0,1,1,”KEY2 (PAUSE key) is pressed!!”
TEXT 100,60,”3”,0,1,1,”End of test”
PRINT 1,1

Downloaded from www.Manualslib.com manuals search engine

 SET KEY1 ON
SET KEY2 ON
END
ENDIF
GOTO START
EOP
DEMO
See Also
OFFEST, PRINT

SET PEEL

Description
This setting is used to enable/disable the self-peeling function.
The default setting for this function is off. When this function is set on, the
printer stops after each label printing, and does not print the next label until
the peeled label is taken away.
This setting will be saved in printer memory when turning off the power.

Syntax
SET PEEL ON/OFF

Parameter Description
ON Enable the self-peeling function
OFF Disable the self-peeing function

Example
REM ***SELF-PEELING FUNCTION ON***
SIZE 3,4
GAP 0,0
DENSITY 8
SPEED 6
DIRECTION 0
REFERENCE 0,0
SET PEEL ON
CLS
TEXT 50,100,"3",0,1,1,"SELF-PEELING FUNCTION TEST"
PRINT 5

See Also
OFFEST, PRINT

Downloaded from www.Manualslib.com manuals search engine

 SET TEAR & SET STRIPPER

Description
This command is used to enable/disable feeding label to gap/black mark
position for tearing off.
This setting will be saved in printer memory when turning off the power.

Syntax
SET TEAR ON/OFF

Parameter Description
ON The label gap will stop at the tear off position after print.

OFF The label gap will NOT stop at the tear off position after
print. The beginning of label will be aligned to print head.

Example
REM ***TEAR FUNCTION ON***
SIZE 3,3
GAP 0.08,0
DENSITY 8
SPEED 4
DIRECTION 0
REFERENCE 0,0
SET PEEL OFF
SET TEAR ON
CLS
TEXT 50,100,"3",0,1,1,"TEAR FUNCTION TEST"
PRINT 1

See Also
SET PEEL

SET HEAD

Description
This setting is used to enable/disable head open sensor. If head open
sensor is closed then when printer head is opened there isn’t any message
returned. This setting will be saved in printer memory.

Syntax
SET HEAD ON /OFF

Downloaded from www.Manualslib.com manuals search engine

 Parameter Description
ON Turn on the “HEAD OPEN” sensor
OFF Turn off the “HEAD OPEN” sensor

Example
SET HEAD ON
SET HEAD OFF

SET COM1

Description
This setting defines communication parameters for printer serial port.

Syntax
SET COM1 baud, parity, data, stop

Parameter Description
baud Baud rate, available baud rates are as listed :
24: 2400 bps
48: 4800 bps
96: 9600 bps
19: 19200 bps

Parity Parity check

N: None parity check
E: Even parity check
O: Odd parity check

data Data bit

8: 8 bits data
7: 7 bits data

stop Stop bit

1: 1 stop bit
2: 2 stop bits

Example
The parallel port is used to setup the printer serial port in this example by
MS-DOS mode. C:\>COPY CON LPT1<ENTER>
SET COM1 19,N,8,1<ENTER>
<CTRL><Z><ENTER>
C:\>

Note: <ENTER> stands for PC keyboard “ENTER” key.

<CTRL><Z> means to hold PC keyboard “CTRL” key then press
PC keyboard <Z> key.

Downloaded from www.Manualslib.com manuals search engine

 SET PRINTKEY

Description
This command will print one label and feed label gap to tear bar position for
tearing away. Press FEED button to print the next label or batch of labels. If
label content includes serial text or barcode, it will change the serial number
accordingly. This setting will be saved in printer memory.

Syntax
SET PRINTEKY OFF/ON/AUTO/<num>

Parameter Description
OFF Disable this function
ON Enable this function
AUTO Enable this function
<num> Numbers of labels will be printed if FEED button is pressed.

Example
Execute:
SIZE 3,2.5
GAP 0.12,0
SET PRINTKEY ON
SET COUNTER @0 1
@0="0001"
CLS
TEXT 10,10,"5",0,1,1,@0
PRINT 1

Downloaded from www.Manualslib.com manuals search engine

 Execute:

Syntax Receive “PRINT m” Print Out

SET PRINTKEY ON or 1.) PRINT 2 Label 1~2
SET PRINTKEY AUTO 2.) Press FEED key Label 3~4

Syntax Receive “PRINT m,n” Print Out

SET PRINTKEY ON or 1.) PRINT 1,2 Label 1, Label 1
SET PRINTKEY AUTO 2.) Press FEED key Label 2, Label 2

Syntax Receive “PRINT -1,n” Print Out

SET PRINTKEY ON or 1.) PRINT -1,2 Label 1, Label 1
SET PRINTKEY AUTO 2.) Press FEED key Label 1, Label 1

Syntax Receive “PRINT m” Print Out

1.) PRINT 2 Label 1~2
SET PRINTKEY 5
2.) Press FEED key Label 3~7

Syntax Receive “PRINT m,n” Print Out

1.) PRINT 1,2 Label 1, Label 1
SET PRINTKEY 5
2.) Press FEED key Label 2~6

Syntax Receive “PRINT -1,n” Print Out

1.) PRINT -1,2 Label 1, Label 1
SET PRINTKEY 5
2.) Press FEED key Label 1, Label 1

Downloaded from www.Manualslib.com manuals search engine

 SET REPRINT

Description
This command will disable/enable reprint the label when the “no paper” or
“no ribbon” or “carriage open” error is occurred.

Syntax

SET REPRINT OFF/ON

Parameter Description
OFF Disable this function
ON Enable this function

Example
SET REPRINT ON

PEEL

Description
This command is used to obtain status of the peel-off sensor. Its attribute is
read only.

Syntax
PEEL

Parameter Description
0 Paper is not on top of peel sensor
1 Paper is on top of peel sensor

Example
DOWNLOAD “DEMO19.BAS”
SIZE 4,4
GAP 0,0
DENSITY 8
SPEED 3
DIRECTION 0
REFERENCE 0,0
SET PEEL OFF
SET LED1 OFF
CLS
IF PEEL=1 THEN LED1=1
EOP

Downloaded from www.Manualslib.com manuals search engine

 KEY1, KEY2

Description
This command is used to read the status of KEY1 ,KEY2 .
Syntax
KEYm=n

Key Return Value

KEY1 (FEED) 0: released
1: pressed
KEY2 (PAUSE) 0: released
1: pressed
Example
DOWNLOAD "DEMO.BAS"
SIZE 3,1
GAP 0,0
SPEED 4
DENSITY 8
DIRECTION 1
REFERENCE 0,0
SET KEY1 OFF
:START
IF KEY1=1 THEN
CLS
TEXT 100,10,"3",0,1,1,"KEY FUNCTION TEST"
PRINT 1,1
GOTO START
EOP
DEMO

Downloaded from www.Manualslib.com manuals search engine

 Printer Global Variables
@LABEL

Description
This variable is used to count how many pieces of labels have been printed.
It can’t be initialized if the printer is reset. It will be memorized if the printer
power is turned off.

Syntax
Write attribute: @LABEL=n or @LABEL=”n”
Read attribute: A=LABEL or A$=STR$(LABEL)

Parameter Description
n Number of labels printed. 0<=n<=999999999
Example
DOWNLOAD "DEMO.BAS"
SIZE 3,2.5
GAP 2 mm,0
SPEED 6
DENSITY 12
CLS
TEXT 10,50,"3",0,1,1,@LABEL
TEXT 10,100,"3",0,1,1,"@LABEL="+STR$(LABEL)
TEXT 10,150,"3",0,1,1,"*****Statement 1*****"
IF LABEL>1000 THEN
TEXT 10,200,"3",0,1,1,"LABEL>1000"
ELSE
TEXT 10,200,"3",0,1,1,"LABEL<1000"
ENDIF
TEXT 10,250,"3",0,1,1,"*****Statement 1*****"
A=LABEL
IF A>1000 THEN
TEXT 10,300,"3",0,1,1,"A>1000"
ELSE
TEXT 10,300,"3",0,1,1,"A<1000"
ENDIF
TEXT 10,350,"3",0,1,1,"*****Statement 3*****"
A$=STR$(LABEL)
IF VAL(A$)>1000 THEN
TEXT 10,400,"3",0,1,1,"VAL(A$)>1000"
ELSE
TEXT 10,400,"3",0,1,1,"VAL(A$)<1000"
ENDIF
PRINT 1,1
EOP

Downloaded from www.Manualslib.com manuals search engine