TECHNICAL DATA SHEET PYG 40 E
PYG 40 250 E
PYG 50 E
PYG 60 E
Flame-Bonded
AWAZEL PYGE Waterproofing Sheet Membranes
High Performance APP Modified Bitumen Waterproofing Membrane
Reinforced with Double Carriers (Polyester + Glass Fiber) REF: AWPYGE-APP-0223
AWAZEL
Compliance: ASTM D 6223, Type I & II, Grade S and SASO 2634
THIS PRODUCT FEATURES & ADVANTAGES
High Performance, APP Modified bituminous membrane, ▪ Ideal to use as Hot Mix under layer
reinforced with two carriers (non woven polyester mat and ▪ High Flexibility at low temperature and stability at high
glass fiber mat). The polyester combines high tensile strength temperature.
and elonga on and glass fiber provides dimensional stability. ▪ Durable and easy to apply.
The special polymer modifier used has great resistance to ▪ Remarkable resistance to aggressive a ack of salts and
ultra-violet radia on.
chemicals.
USES & APPLICATIONS
▪ High tensile strength, elonga on and dimensional stability.
▪ Ideal to use as single and/or double layers waterproofing of ▪ Heavy duty double carriers provides an -root characteris cs
reinforced concrete bridge decks.
▪ Also used for general waterproofing applica ons where TYPICAL INSTALLATION PROCEDURES
impact resistance, toughness and dimensional stability are ▪ The substrate should be cleaned and primed with
required. AWAZEL PRIMER D 41 and allowed to dry.
▪ Maybe used as a root barrier in light, short roots vegeta on. ▪ In roof waterproofing applica ons, these membrane can
Dense vegeta on requires an addi onal layer of AWAZEL be installed as fully bonded or loose-laid.
DIMPLE SHEET, HDPE drainage board as the reliable root ▪ For bridge deck applica ons, they must be fully bonded
barrier. to avoid wrinkling caused by heavy vehicles breaking in
the bridge.
HEALTH & SAFETY ▪ Torching should be done by skilled labor and should be
▪ All safety measures should be observed during installa on controlled so that only the PE film is melted and the
▪ Fire ex nguishers should be kept nearby and handy on site asphalt coa ng is so ened sufficient to bond the
▪ Installa on personnel should wear protec ve gear at all membrane.
mes during installa on. ▪ All lap joints should be smoothed and sealed using a
▪ For more informa on on safety measures consult the heated round-nosed trowel.
product's Material Safety Data Sheet. ▪ In looselaid applica ons, only the lap joints, areas
around penetra ons (pipes etc.), upstands and a 30 cm
STORAGE & HANDLING wide strip around the perimeter of the work should be
▪ Rolls should be kept in an upright posi on in a properly bonded.
ven lated and shaded storage area. ▪ The overlap joints should be 5 to 10 cm at the sides and
▪ Keep away from any source of flame. 15 cm at the end.
▪ Avoid materials stacking
KINGDOM OF SAUDI ARABIA
ARABIAN WATERPROOFING INDUSTRIES Co. Riyadh: TEL + 966 11 478 2876, Jeddah: TEL: + 966 12 660 1740, Dammam: + 966 13 834 1853, info@awazel.com
UAE - DUBAI: UAE - ABU DHABI: KUWAIT: QATAR: EGYPT:
AWAZEL INTERNATIONAL L.L.C AWAZEL INTERNATIONAL L.L.C AWAZEL KUWAIT AWAZEL INTERNATIONAL QATAR AWAZEL MISR Co. L.L.C
Ras Al Khor Industrial Area 2 Musaffah Industrial Area 3 FOR BUILDING MATERIALS Co. Sayer Building Gate No. 48, 2nd Floor Cairo Complex, Ankara Street
P.O.Box 37724, Dubai P.O.Box 108483, Abu Dhabi Al Hamra Bldg., 3rd Floor, Office C202, Barwa Commercial Av. Doha Sheraton, Cairo, Egypt
TEL: +97143433032 TEL: +97125548220 Office No. 307, Salmiya - Kuwait TEL: +97444420571 TEL: +20226785836
infouae@awazel.com infoauh@awazel.com TEL: +96525712223 salesqatar@awazel.com egypt@awazel.com
awazel.kw@awazel.com
TECHNICAL DATA SHEET PYG 40 E
PYG 40 250 E
PYG 50 E
PYG 60 E
AWAZEL PYGE Flame-Bonded
High Performance APP Modified Bitumen Waterproofing Membrane
Reinforced with Double Carriers (Polyester + Glass Fiber)
Waterproofing Sheet Membranes
Compliance: ASTM D 6223, Type I & II, Grade S and SASO 2634 REF: AWPYGE-APP-0223
AWAZEL
CHARACTERISTICS
NOMINAL VALUES
PROPERTY TEST METHOD
PYG 40 E PYG 40 250 E PYG 50 E PYG 60 E
So ening Point, °C >115 ASTM D 36
Penetra on at 25 °C, 0.1 mm 15 - 30 ASTM D 5
Tensile strength, N/5 cm 1000 1200 1200 1250 ASTM D 5147
Longitudinal & Transverse 800 1000 1000 1050 ASTM D 146
Tensile strength, ASTM D 6223, Type I Type II ASTM D 5147
kN/m, Longitudinal & Transverse ≥ 11.4 ≥ 17.5 ASTM D 146
Tensile strength, kN/m 23 30 ASTM D 5147
-18 °C, Longitudinal & Transverse 15 20 ASTM D 146
Ul mate Elonga on, % 45 ASTM D 5147
Longitudinal & Transverse 50 ASTM D 146
Elonga on at -18 °C, % 26 ASTM D 5147
Longitudinal & Transverse 30 ASTM D 146
Elonga on, ASTM D 6223, % ≥ 3.00 ASTM D 5147
Longitudinal & Transverse ASTM D 146
Tear Resistance, N 500 650 700 700
Longitudinal & Transverse 500 500 ASTM D 4073
400 450
Lap joint strength, N/5 cm 1000 1200 1200 1250 UEAtc M.O.A.T.
Longitudinal & Transverse 800 1000 1000 1050 30 & 27
Load Strain Product 49,500 54,000 54,000 56,250 CGSB 37-GP 56 M
Longitudinal & Transverse 40,000 50,000 50,000 52,500
Hydrosta c Pressure Resistance No Leakage DIN 52123
up to 7 bars
Cold flexibility at -5 to -10 °C No Cracking UEAtc M.O.A.T. 30
Flexibility, ASTM Requirement No Cracking at 0°C ASTM D 5147
Heat resistance at 150 °C No Flowing UEAtc M.O.A.T. 30
Moisture Content (W.V.T.), % ≤ 1.0 ASTM E 96
Water Absorp on, % ≤ 0.12 ASTM D 5147
Sta c Puncture Resistance L3 (15 Kg) L4 (25 Kg) UEAtc M.O.A.T. 27
Dynamic Puncture Resistance I3 (8-12mm indenter) I4 (4-6mm indenter) UEAtc M.O.A.T. 27
Dimensional Stability, % ≤ 1.0 ASTM D 5147
Resistance to Aging a er 2000 hrs No Deteriora ons ASTM D 4799
NOTE: The above informaƟon provided to the best of our knowledge at the Ɵme of manufacturing. Values may vary within tolerance due to raw material changes and/or unforeseen circumstances.
AWAZEL Company reserves the right to alter the product's specificaƟon without prior noƟce. Extra details maybe provided upon request.
SUPPLY & PRESENTATION
NOMINAL VALUES
PROPERTY PYG 40 E PYG 40 250 E PYG 50 E PYG 60 E TEST METHOD
Roll size, m 10 x 1 m 10 x 1 m 8x1m 8x1m ASTM D 5147
Thickness, mm 4.0 4.0 5.0 6.0 ASTM D 5147
Unit weight (Plain), Kg/m2 4.0 4.0 5.0 6.0 ASTM D 5147
Carrier (Polyester), g/m2 200 250 250 250 ASTM D 5147
Glass Fiber, g/m2 50-60 50-60 50-60 50-60 UEAtc M.O.A.T. 30
Coa ng Asphalt Type APP Modified Asphalt
KINGDOM OF SAUDI ARABIA
ARABIAN WATERPROOFING INDUSTRIES Co. Riyadh: TEL + 966 11 478 2876, Jeddah: TEL: + 966 12 660 1740, Dammam: + 966 13 834 1853, info@awazel.com
UAE - DUBAI: UAE - ABU DHABI: KUWAIT: QATAR: EGYPT:
AWAZEL INTERNATIONAL L.L.C AWAZEL INTERNATIONAL L.L.C AWAZEL KUWAIT AWAZEL INTERNATIONAL QATAR AWAZEL MISR Co. L.L.C
Ras Al Khor Industrial Area 2 Musaffah Industrial Area 3 FOR BUILDING MATERIALS Co. Sayer Building Gate No. 48, 2nd Floor Cairo Complex, Ankara Street
P.O.Box 37724, Dubai P.O.Box 108483, Abu Dhabi Al Hamra Bldg., 3rd Floor, Office C202, Barwa Commercial Av. Doha Sheraton, Cairo, Egypt
TEL: +97143433032 TEL: +97125548220 Office No. 307, Salmiya - Kuwait TEL: +97444420571 TEL: +20226785836
infouae@awazel.com infoauh@awazel.com TEL: +96525712223 salesqatar@awazel.com egypt@awazel.com
awazel.kw@awazel.com
