Installation Instructions
D
A
G
L
L
F B
H
C C
I
H
K
J
E
G
M ×2
M
A×1 B×1 C×2 D×1
E×2
F×1 G×4 K×2
H×2
I×2 J×2 L×2 M×2 N×18 O×2 P×33
Q×3 R×4 S×70 T×16 U×4 V×2 W×4 X×2
step1 Align the four Parts G with the four extensions on the corners of the left side plate (Part A) and insert them
downward, then secure them with the four bolts P.
Note: the larger holes on part G should overlap the holes on the extensions from part A.
A
（front）
（back）
G P×4
Align the two parts H with the two remaining extensions on the left side panel (part A) and insert
step2 them downwards. Then secure them with two bolts P.
Note the direction: The side with the small square piece at the bottom on the Part H should be aligned with
the direction of the nut on Part A. The small square piece of Part H faces the bottom.
H
（top）
（front）
（bottom） （back） P×2
Fully insert the small short tube extending from the right side panel (part B) into the six square tubes
step3 (4 parts G and 2 parts H) and secure with the six bolts.
P
（front） （back）
A
P×6
step4 Put the two rear walls together ,and put three bolts and nuts to hold them in place.
Q
P
C
C
P×3 Q×3
step5 Place the rear wall assembly into the cabinet from the outside and secure with 14 screws.
（front）
（back）
S×14
step6 For ease of assembly, lay the cabinet flat on the floor with the front facing up. Place the base
plate ( Part F) into the cabinet and push down, then secure with the 12 screws.
（front）
（back）
E
S
S×12
step7 Place the other part E into the cabinet and push down until the holes line up with the holes in the
frame, then secure with the 12 screws.
（front）
（back）
S×12
Place the top plate ( Part D) from above, aligning it with the top edge of the frame, and then
step8 use ten hinges N to connect the top plate to the cabinet with ten bolts P (to attach the top
plate) and ten screws S (to attach the cabinet).
N
S
（front）
（back）
P×10 S×10 N×10
Place part F into the cabinet, push down until the holes line up with the holes in the frame, and then
step9 secure it in place with the 8 hinges N, 8 bolts P with 8 screws S.
The side of the Part F with the hole faces down and the
side with the hole farther from the edge faces front.
N
S
P
（front）
（back）
P×8 S×8 N×8
step10 Attach the 2 parts I to the left side plate and secure with 4 screws, then attach the 2 parts J to the
right side plate and secure with 4 screws.Note the distinction between I and J (part I is mounted
on the left side panel, part J is mounted on the right side panel).
I
J
Note: The notch direction is
downward.
（back）
（front）
I
T T
J T×8
step11 Attach the two magnets (part R) to the
two panels (part K) separately. Attach the handle V to the two door
panels K and secure with the bolts
W.
R V
×2
K
R
V×2 W×4 R×4
step12 Before placing the door panel K into the cabinet, press the springs on each side and snap them into
the holes in the left and right side panels.
If the spring screw is missing from the door, you can find
the screw X in the hardware package to install it.
K
step13 Pull Parts I and J on the left and right sides so that the connecting tabs below them line up with
the holes in the door panel K. Attach them with 8 screws T.
T T
K
J
T×8
step14
Install the other panel K in the same way.
step15 Attach 2 parts L and 2 parts M to the front frame
and secure with 14 screws.
Note: Part M is mounted on two corners at the
S bottom of the cabinet and part L is mounted on
two corners at the top.
L
L
M
S
S×14
step16 The cabinet can be fixed to the wall as needed.
O O
Wall
O×2
step17
Finally hang hooks U on the cabinet according to your preference.
U×4
step18
