0% found this document useful (0 votes)
23 views26 pages

Iocl Ea Eepdf

Uploaded by

Rahul Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
23 views26 pages

Iocl Ea Eepdf

Uploaded by

Rahul Kumar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 26

Participant ID 1281290430100001

Participant Name NAND KISHOR MAURYA


Test Center Name TCS Gito Bitan
Test Date 29/09/2024
Test Time 1:30 PM - 3:30 PM
Subject ENGINEERING ASSISTANT ELECTRICAL

Section : Technical

Q.1 What does a higher efficiency value indicate for a transmission line?
Ans A. Equal power delivery at the receiving end and the sending end

B. Higher line losses and lower power delivery at the receiving end

C. Lower line losses and higher power delivery at the receiving end

D. Unstable operation of the transmission line

Question ID : 630680368270
Option 1 ID : 6306801434523
Option 2 ID : 6306801434521
Option 3 ID : 6306801434522
Option 4 ID : 6306801434524
Status : Answered
Chosen Option : C

Q.2 Which of the following processes takes place in Biomass energy conversion?
Ans A. Chemical conversion and biochemical conversion

B. Electrochemical conversion, biochemical conversion and chemical


conversion
C. Thermal conversion, chemical conversion, biochemical conversion
and electrochemical conversion
D. Thermal conversion, chemical conversion and electrochemical
conversion

Question ID : 630680971367
Option 1 ID : 6306803809570
Option 2 ID : 6306803809568
Option 3 ID : 6306803809569
Option 4 ID : 6306803809567
Status : Answered
Chosen Option : C

Q.3 In the short circuit test on a star connected three phase alternator, a field current of 5 A
gives an armature current of 40 A. In the open circuit test, the same field current produces
an open circuit voltage of 240 V per phase. What is the synchronous impedance per phase?
Ans A. 6 Ω

B. 8 Ω

C. 12 Ω

D. 48 Ω

Question ID : 630680618278
Option 1 ID : 6306802419443
Option 2 ID : 6306802419442
Option 3 ID : 6306802419444
Option 4 ID : 6306802419441
Status : Answered
Chosen Option : A
Q.4 What types of serial communication does the 8051 microcontroller support?
Ans A. Synchronous and half-duplex

B. asynchronous and synchronous.

C. asynchronous and full-duplex

D. Half duplex and full duplex

Question ID : 630680339859
Option 1 ID : 6306801321957
Option 2 ID : 6306801321959
Option 3 ID : 6306801321958
Option 4 ID : 6306801321960
Status : Answered
Chosen Option : A

Q.5 The net area under the load duration curve denotes:
Ans A. system’s average load

B. generated energy during the duration

C. system’s base load

D. system’s peak load

Question ID : 630680333463
Option 1 ID : 6306801297126
Option 2 ID : 6306801297127
Option 3 ID : 6306801297128
Option 4 ID : 6306801297125
Status : Answered
Chosen Option : B

Q.6 How is the starting resistance used in a shunt motor connected to the armature and the
field winding?
Ans A. The starting resistance is connected in series with the armature.

B. The starting resistance is connected in series with the field winding.

C. The starting resistance is connected in series with both the field winding and
armature winding.
D. The starting resistance is connected in parallel with the armature.

Question ID : 630680503344
Option 1 ID : 6306801966960
Option 2 ID : 6306801966958
Option 3 ID : 6306801966957
Option 4 ID : 6306801966959
Status : Answered
Chosen Option : C

Q.7 The phasor of the voltages VA and VB is given in the diagram. Find the voltage VAB.

Ans
A.

B.

C.

D.

Question ID : 630680328974
Option 1 ID : 6306801279851
Option 2 ID : 6306801279852
Option 3 ID : 6306801279850
Option 4 ID : 6306801279849
Status : Answered
Chosen Option : C
Q.8 In a shaded pole motor, the stator is made of _______________.
Ans A. laminated salient poles with a slot at one-third distance from one edge on each pole

B. smooth cylindrical structure with slots all along the periphery housing the shading
coil
C. smooth cylindrical structure with the shading ring around the cylindrical periphery

D. laminated salient poles with a number of slots cut in each pole

Question ID : 630680694992
Option 1 ID : 6306802722207
Option 2 ID : 6306802722210
Option 3 ID : 6306802722209
Option 4 ID : 6306802722208
Status : Answered
Chosen Option : A

Q.9 यदि बिंदु संतुलन (point balance) पर कोई यांत्रिक विस्थापन होता है, तो राशि का मान (value of the
quantity) मापा जाता है। इस प्रकार के यंत्र को _________ कहा जाता है।

Ans A. निरपेक्ष यंत्र (Absolute instrument)

B. द्वितीयक यंत्र (Secondary instrument)

C. शून्य प्रकार के यंत्र (Null type instrument)

D. विक्षेपण प्रकार के यंत्र (Deflection type instrument)

Question ID : 630680396175
Option 1 ID : 6306801544814
Option 2 ID : 6306801544815
Option 3 ID : 6306801544813
Option 4 ID : 6306801544812
Status : Answered
Chosen Option : C

Q.10 If v(t) = 100Sin(50t − 50°) V, then which of the following statements is/are correct regarding
the circuit shown in the given diagram?

(a) The current i(t) in the circuit equals to 20000 Sin(50t+40°) A.


(b) The current i(t) in the circuit leads the voltage v(t) by 40°.
(c) Admittance = −j200 Ω.
Ans A. Only (a)

B. (a), (b) and (c)

C. Both (a) and (b)

D. Both (a) and (c)

Question ID : 630680328978
Option 1 ID : 6306801279868
Option 2 ID : 6306801279866
Option 3 ID : 6306801279867
Option 4 ID : 6306801279865
Status : Answered
Chosen Option : A

Q.11 Which of the following steps describes how a microprocessor operate?


Ans A. I/O read, opcode fetch, memory read, memory write, I/O write

B. Opcode fetch, memory write, memory read, I/O read, I/O write

C. I/O write, opcode fetch, memory write, memory read, I/O read

D. Opcode fetch, memory read, memory write, I/O read, I/O write

Question ID : 630680339829
Option 1 ID : 6306801321840
Option 2 ID : 6306801321838
Option 3 ID : 6306801321839
Option 4 ID : 6306801321837
Status : Answered
Chosen Option : D
Q.12 In the voltage equation of the DC shunt motor, which of the following is NOT a parameter of
voltage equation?
Ans A. Back EMF

B. Brush voltage

C. Voltage drop at armature

D. Voltage drop at load

Question ID : 630680379051
Option 1 ID : 6306801477251
Option 2 ID : 6306801477252
Option 3 ID : 6306801477254
Option 4 ID : 6306801477253
Status : Answered
Chosen Option : D

Q.13 The strength of the sawtooth voltage produced by the time base generator is amplified by
using _______.
Ans A. Time Base Generators

B. Trigger Circuits

C. Horizontal Amplifiers

D. Vertical Amplifiers

Question ID : 630680396147
Option 1 ID : 6306801544702
Option 2 ID : 6306801544703
Option 3 ID : 6306801544701
Option 4 ID : 6306801544700
Status : Answered
Chosen Option : C

Q.14 Which of the following steps should be followed while reading data from an LCD?
Ans A. The R/W pin is raised.

B. The R/W pin is set high, and the E pin has a low to high pulse.

C. low to high pulse at E pin

D. E pin has a high to low pulse, while R/W pin is set to low.

Question ID : 630680366335
Option 1 ID : 6306801426858
Option 2 ID : 6306801426859
Option 3 ID : 6306801426857
Option 4 ID : 6306801426860
Status : Answered
Chosen Option : B

Q.15 In IGBT semiconductor to form PNPN layer the _____________ electrode connected to P layer.
Ans A. drain

B. gate

C. collector

D. emitter

Question ID : 630680374792
Option 1 ID : 6306801460337
Option 2 ID : 6306801460338
Option 3 ID : 6306801460335
Option 4 ID : 6306801460336
Status : Answered
Chosen Option : D
Q.16 Determine the value of current I in the circuit shown here.

Ans A. -2 A

B. +2 A

C. -8 A

D. +8 A

Question ID : 630680209175
Option 1 ID : 630680810915
Option 2 ID : 630680810916
Option 3 ID : 630680810917
Option 4 ID : 630680810918
Status : Answered
Chosen Option : A

Q.17 Why is a charge controller necessary for a PV system with batteries?


Ans A. To generate electricity from solar energy

B. To track the movement of the sun

C. To increase the voltage output of the solar cells

D. To prevent overcharging of the batteries

Question ID : 630680374472
Option 1 ID : 6306801459067
Option 2 ID : 6306801459068
Option 3 ID : 6306801459069
Option 4 ID : 6306801459070
Status : Answered
Chosen Option : D

Q.18 The given circuit represents __________.

Ans A. auxiliary commutation

B. external pulse commutation

C. load commutation

D. complementary commutation

Question ID : 630680352185
Option 1 ID : 6306801370840
Option 2 ID : 6306801370839
Option 3 ID : 6306801370837
Option 4 ID : 6306801370838
Status : Answered
Chosen Option : C
Q.19 What is the advantage of operating Type-D Wind Power Plants (WPPs) with Wound Rotor
Synchronous Generators (WRSG)?
Ans A. Greater power output

B. Smoother grid connection

C. Lower energy losses

D. Reduced mechanical stresses

Question ID : 630680392251
Option 1 ID : 6306801529350
Option 2 ID : 6306801529351
Option 3 ID : 6306801529353
Option 4 ID : 6306801529352
Status : Answered
Chosen Option : D

Q.20 Which pin(s) is/are used to select the step size in the ADC0808/0809 IC?
Ans A. Vin/Vout

B. Vref/2 and Vin

C. Vin

D. Vref

Question ID : 630680358745
Option 1 ID : 6306801396947
Option 2 ID : 6306801396948
Option 3 ID : 6306801396945
Option 4 ID : 6306801396946
Status : Answered
Chosen Option : B

Q.21 Which of the following should a tariff include?


(a) Recovery of cost of producing electrical energy at the power station.
(b) A suitable profit on the capital investment.
(c) Recovery of cost of operation and maintenance of supply of electrical energy.
Ans A. (a) and (b) only

B. (a), (b) and (c)

C. (a) and (c) only

D. (b) and (c) only

Question ID : 630680509632
Option 1 ID : 6306801991733
Option 2 ID : 6306801991736
Option 3 ID : 6306801991735
Option 4 ID : 6306801991734
Status : Answered
Chosen Option : B

Q.22 Which of the following is NOT a type of power factor tariff?


Ans A. kVA maximum demand tariff

B. Two-part tariff

C. Sliding scale tariff

D. kW and kVAR tariff

Question ID : 630680509638
Option 1 ID : 6306801991757
Option 2 ID : 6306801991760
Option 3 ID : 6306801991758
Option 4 ID : 6306801991759
Status : Answered
Chosen Option : A
Q.23 To adjust the power factor of the synchronous motor, we have to adjust the ____________.
Ans A. supply frequency

B. speed

C. supply voltage

D. excitation

Question ID : 630680618154
Option 1 ID : 6306802418959
Option 2 ID : 6306802418957
Option 3 ID : 6306802418960
Option 4 ID : 6306802418958
Status : Answered
Chosen Option : D

Q.24 The value of internal flux linkage at a distance of x along a straight cylindrical conductor
carrying a current I of radius r metres and surrounded by a magnetic field is:
Ans
A.

B.

C.

D.

Question ID : 630680396784
Option 1 ID : 6306801547221
Option 2 ID : 6306801547220
Option 3 ID : 6306801547223
Option 4 ID : 6306801547222
Status : Answered
Chosen Option : B

Q.25

Ans A. 25 Ω

B. 23 Ω

C. 21 Ω

D. 15 Ω

Question ID : 630680334718
Option 1 ID : 6306801302130
Option 2 ID : 6306801302131
Option 3 ID : 6306801302132
Option 4 ID : 6306801302129
Status : Answered
Chosen Option : D

Q.26 What is the function of the magnetising component of the primary current in an actual
transformer working at no load?
Ans A. To counteract the secondary MMF

B. To sustain the alternating flux in the core

C. To supply copper losses in the windings

D. To supply iron losses in the core

Question ID : 630680503332
Option 1 ID : 6306801966912
Option 2 ID : 6306801966911
Option 3 ID : 6306801966910
Option 4 ID : 6306801966909
Status : Answered
Chosen Option : B
Q.27 What can be said about the value of the diversity factor?
Ans A. It varies depending on the size of the power station.

B. It is always greater than one.

C. It is always less than one.

D. It is always equal to one.

Question ID : 630680374429
Option 1 ID : 6306801458898
Option 2 ID : 6306801458897
Option 3 ID : 6306801458895
Option 4 ID : 6306801458896
Status : Answered
Chosen Option : B

Q.28 Which of the following options is NOT true regarding active power in an AC series circuit?
Ans A. Active power is dissipated on resistive component of impedance

B. Active power is directly proportional to circuit power factor

C. Active power is the useful power in an AC circuit

D. Active power is independent of power factor of circuit

Question ID : 630680334710
Option 1 ID : 6306801302100
Option 2 ID : 6306801302098
Option 3 ID : 6306801302097
Option 4 ID : 6306801302099
Status : Answered
Chosen Option : D

Q.29 Select the INCORRECT statements from among the following with respect to High Voltage
Schering bridge.
1)Earthed screens are used to avoid the effect of earth capacitance between high and low
impedance arms.
2)Wagner ground connection is used to eliminate the errors due to inter- capacitance
between high and low impedance arms.
3)Earthed screens are used to avoid the errors due to inter- capacitance between high and
low impedance arms.
4)Wagner ground connection is used to eliminate the effect of earth capacitance on the
galvanometer and contact leads.
Ans A. Statements(3) and (4)

B. Statements(2) and (3)

C. Statements (1) and (2)

D. Statements (1) and (4)

Question ID : 630680424748
Option 1 ID : 6306801657304
Option 2 ID : 6306801657305
Option 3 ID : 6306801657303
Option 4 ID : 6306801657306
Status : Answered
Chosen Option : C

Q.30 The most economical transmission voltage is _________ per km of transmission line.
Ans A. 750 volts

B. 850 volts

C. 440 volts

D. 650 volts

Question ID : 630680401928
Option 1 ID : 6306801567460
Option 2 ID : 6306801567461
Option 3 ID : 6306801567458
Option 4 ID : 6306801567459
Status : Answered
Chosen Option : C
Q.31 The _____ instruction set enables the user to substitute a single instruction for numerous
simple ones.
Ans A. RISC

B. CISC

C. MISC

D. EPM

Question ID : 630680358751
Option 1 ID : 6306801396970
Option 2 ID : 6306801396969
Option 3 ID : 6306801396971
Option 4 ID : 6306801396972
Status : Answered
Chosen Option : A

Q.32 In a half bridge converter, the flyback converter is used to provide ______ to higher or lower
level of input voltage.
Ans A. input current

B. input voltage

C. output voltage

D. output current

Question ID : 630680352127
Option 1 ID : 6306801370608
Option 2 ID : 6306801370605
Option 3 ID : 6306801370606
Option 4 ID : 6306801370607
Status : Answered
Chosen Option : B

Q.33 The voltage determined by the DC potentiometer is independent of __________.


Ans A. energy consumption

B. load current

C. load power

D. source resistance

Question ID : 630680396193
Option 1 ID : 6306801544887
Option 2 ID : 6306801544884
Option 3 ID : 6306801544886
Option 4 ID : 6306801544885
Status : Answered
Chosen Option : D

Q.34 The amorphous transformer is known for their improved _______.


Ans A. energy efficiency

B. resistance to extreme temperatures

C. voltage regulation

D. mechanical strength

Question ID : 630680373454
Option 1 ID : 6306801455087
Option 2 ID : 6306801455089
Option 3 ID : 6306801455088
Option 4 ID : 6306801455090
Status : Answered
Chosen Option : B
Q.35 A voltage V = 200Sin(t) is applied to a circuit consisting of a 4 Ω resistor and a 0.25 F
capacitor that are connected in series. The maximum value of the current through the
circuit is _____.
Ans A.

B.

C.

D.

Question ID : 630680338929
Option 1 ID : 6306801318305
Option 2 ID : 6306801318307
Option 3 ID : 6306801318306
Option 4 ID : 6306801318308
Status : Answered
Chosen Option : A

Q.36 Full bridge converter has three stages, of which the first stage is ___________.
Ans A. rectifier network

B. transformer network

C. square wave generator

D. energy transformer network

Question ID : 630680387309
Option 1 ID : 6306801509922
Option 2 ID : 6306801509923
Option 3 ID : 6306801509924
Option 4 ID : 6306801509925
Status : Answered
Chosen Option : B

Q.37 ठोस बायोमास संसाधन के रूप में निम्नलिखित में से कौन-सा उपयुक्त नहीं है?

Ans A. भूसी (Husk)

B. धातु और प्लास्टिक अपशिष्ट

C. एल्कोहॉल मद्यनिर्माणशाला (Alcohol Breweries)

D. कागज और गत्ते

Question ID : 630680971399
Option 1 ID : 6306803809647
Option 2 ID : 6306803809650
Option 3 ID : 6306803809648
Option 4 ID : 6306803809649
Status : Answered
Chosen Option : C

Q.38 Which of the following statements is/are correct regarding reciprocity theorem?
a) It is applicable to a multisource network.
b) It is applicable to a circuit containing both independent and dependent sources.
c) It is applicable to a network having only one independent source.
Ans A. Only (c)

B. Only (a)

C. Only (b) and (c)

D. Only (a) and (b)

Question ID : 630680328968
Option 1 ID : 6306801279828
Option 2 ID : 6306801279827
Option 3 ID : 6306801279826
Option 4 ID : 6306801279825
Status : Answered
Chosen Option : A
Q.39 Which of the following registers does NOT fall under the umbrella of special function
registers in 8051?
Ans A. P0 and P1

B. SP and PC

C. TH0 and TL0

D. TCON and TMOD

Question ID : 630680358752
Option 1 ID : 6306801396976
Option 2 ID : 6306801396973
Option 3 ID : 6306801396975
Option 4 ID : 6306801396974
Status : Answered
Chosen Option : A

Q.40

Ans A. 198.14

B. 200

C. 168.4

D. 270

Question ID : 630680374791
Option 1 ID : 6306801460332
Option 2 ID : 6306801460334
Option 3 ID : 6306801460333
Option 4 ID : 6306801460331
Status : Answered
Chosen Option : C

Q.41 Squirrel cage induction motor requires only periodic maintenance as there are _________.
Ans A. semi-closed slots

B. no brushes and slip rings

C. no commutator

D. open slots

Question ID : 630680337195
Option 1 ID : 6306801311504
Option 2 ID : 6306801311501
Option 3 ID : 6306801311502
Option 4 ID : 6306801311503
Status : Answered
Chosen Option : B

Q.42 How is the transposition of line conductors carried out?


Ans A. Increasing the number of conductors in each phase

B. Adjusting the voltage levels in each phase

C. Changing the positions of the three phases on the line supports

D. Balancing the power transfer between the phases

Question ID : 630680368271
Option 1 ID : 6306801434526
Option 2 ID : 6306801434528
Option 3 ID : 6306801434525
Option 4 ID : 6306801434527
Status : Answered
Chosen Option : B
Q.43 Which of the following points is true about slip ring induction motors?
A) Low power factor at light loads
B) Sensitivity to fluctuations in the supply voltage
C) Low starting torque
D) Poor speed regulation
Ans A. B, C and D

B. A, C and D

C. A, B and D

D. A, B and C

Question ID : 630680339366
Option 1 ID : 6306801320035
Option 2 ID : 6306801320036
Option 3 ID : 6306801320033
Option 4 ID : 6306801320034
Status : Answered
Chosen Option : C

Q.44 The optimising fan speed contributes to energy conservation by ______.


Ans A. increasing wind-age loss

B. increasing energy consumption

C. reducing fan lifespan

D. improving ventilation efficiency

Question ID : 630680403609
Option 1 ID : 6306801573929
Option 2 ID : 6306801573927
Option 3 ID : 6306801573928
Option 4 ID : 6306801573926
Status : Answered
Chosen Option : D

Q.45 The fastest rise time a sine wave can have to be accurately reproduced by the instrument is
350 ns. What is the value of bandwidth of the oscilloscope?
Ans A. 1 MHz

B. 10 MHz

C. 0.1 MHz

D. 0.01 MHz

Question ID : 630680405719
Option 1 ID : 6306801582021
Option 2 ID : 6306801582020
Option 3 ID : 6306801582022
Option 4 ID : 6306801582023
Status : Marked For Review
Chosen Option : A

Q.46 Which of the following is the right is the condition for maximum power developed by the
motor if Ia = Armature current, Ra = Armature resistance and V = Terminal voltage and Eb =
Back EMF?
Ans
A.

B.

C.

D.

Question ID : 630680503357
Option 1 ID : 6306801967010
Option 2 ID : 6306801967011
Option 3 ID : 6306801967012
Option 4 ID : 6306801967009
Status : Answered
Chosen Option : D
Q.47 The calibration of DC potentiometers is carried out by instruments that are _________.
Ans A. DC only

B. AC only

C. either AC or DC

D. both AC and DC

Question ID : 630680396189
Option 1 ID : 6306801544868
Option 2 ID : 6306801544869
Option 3 ID : 6306801544871
Option 4 ID : 6306801544870
Status : Answered
Chosen Option : A

Q.48 A DC shunt motor with a voltage of 200 volts and a speed of 1000 revolutions per minute
requires an armature current of 20 amps. It is necessary to slow down to 500 revolutions
per minute. If the initial resistance of the armature is 0.5 Ω, what must the value of the
resistance that is injected into the armature circuit be? Consider that the current through
the armature will remain the same during this process.
Ans A. 0 Ω

B. 4.75 Ω

C. 5.5 Ω

D. 8.5 Ω

Question ID : 630680503351
Option 1 ID : 6306801966985
Option 2 ID : 6306801966987
Option 3 ID : 6306801966986
Option 4 ID : 6306801966988
Status : Answered
Chosen Option : D

Q.49 How does one move the entire display to the right on an LCD?
Ans A. 0 x 18

B. 0 x 1C

C. 0 x 0F

D. 0 x 01

Question ID : 630680339855
Option 1 ID : 6306801321942
Option 2 ID : 6306801321941
Option 3 ID : 6306801321944
Option 4 ID : 6306801321943
Status : Answered
Chosen Option : C

Q.50 How are Aggregated Technical and Commercial (ATC) losses usually expressed when
analysing distribution systems on a regional level?
Ans A. In terms of harmonics

B. In terms of power factor

C. As a percentage of power generation

D. In kilowatt-hours

Question ID : 630680396116
Option 1 ID : 6306801544577
Option 2 ID : 6306801544579
Option 3 ID : 6306801544578
Option 4 ID : 6306801544576
Status : Answered
Chosen Option : C
Q.51 What is the voltage equation of a DC motor commonly referred to as?
Ans A. Ohm's law

B. Lenz's law

C. Faraday's law

D. Motor equation

Question ID : 630680426274
Option 1 ID : 6306801663199
Option 2 ID : 6306801663201
Option 3 ID : 6306801663200
Option 4 ID : 6306801663202
Status : Answered
Chosen Option : A

Q.52 The given circuit represents ____________.

Ans A. line interactive UPS

B. off-line UPS

C. on-line UPS

D. no line UPS

Question ID : 630680387311
Option 1 ID : 6306801509932
Option 2 ID : 6306801509933
Option 3 ID : 6306801509931
Option 4 ID : 6306801509930
Status : Answered
Chosen Option : C

Q.53 A physical quantity of energy that is converted from one form to another by an electronic
device is referred to as ________.
Ans A. Transistor

B. Transducer

C. Sensor

D. Rectifier

Question ID : 630680339821
Option 1 ID : 6306801321805
Option 2 ID : 6306801321808
Option 3 ID : 6306801321806
Option 4 ID : 6306801321807
Status : Answered
Chosen Option : B

Q.54 If the bandwidth of an oscilloscope is given as direct current to 35 MHz, what is the fastest
rise time a sine wave can have to be produced accurately by the oscilloscope?
Ans A. 0.01 ns

B. 0.1 s

C. 10 s

D. 10 ns

Question ID : 630680405720
Option 1 ID : 6306801582027
Option 2 ID : 6306801582026
Option 3 ID : 6306801582024
Option 4 ID : 6306801582025
Status : Answered
Chosen Option : D
Q.55 How does the Intelligent Power Factor Controller (IPFC) contribute to optimising power
factor correction?
Ans A. By increasing power factor correction without considering load conditions

B. By dynamically adjusting power factor correction to minimise losses and improve


efficiency
C. By adding more capacitors to the system

D. By decreasing power factor correction under all circumstances

Question ID : 630680373444
Option 1 ID : 6306801455047
Option 2 ID : 6306801455048
Option 3 ID : 6306801455050
Option 4 ID : 6306801455049
Status : Answered
Chosen Option : B

Q.56 In a three-phase star connected load, the phase voltage and phase current of a phase is
given by Vph = 2 + j4 V and Iph = 3 − j2 A. The complex power will be _______.

Ans A. (-6 + j48 ) VA

B. (-2 + j16 ) VA

C. (14 + j8 ) VA

D. (42 + j24 ) VA

Question ID : 630680328982
Option 1 ID : 6306801279882
Option 2 ID : 6306801279883
Option 3 ID : 6306801279884
Option 4 ID : 6306801279881
Status : Answered
Chosen Option : D

Q.57 शिरोपरि पारेषण चालकों की स्ट्रिंगिंग की किस विधि में किसी वाहन या खींचने वाले उपकरण द्वारा चालक को
जमीन पर खींचा जाता है?
Ans A. अर्ध-तनाव स्ट्रिंगिंग (Semi-tension stringing)

B. पूर्ण-तनाव स्ट्रिंगिंग (Full-tension stringing)

C. स्लैक स्ट्रिंगिंग (Slack stringing)

D. हेलीकाप्टर स्ट्रिंगिंग (Helicopter stringing)

Question ID : 630680396765
Option 1 ID : 6306801547145
Option 2 ID : 6306801547146
Option 3 ID : 6306801547144
Option 4 ID : 6306801547147
Status : Answered
Chosen Option : C

Q.58 What function does the Power Electronic Converter (PEC) serve in type-D geared Wind
Power Plants (WPPs) with Permanent Magnet Synchronous Generators (PMSGs)?
Ans A. It decouples the generator from the grid

B. It connects the generator to the mechanical drive train

C. It generates electrical power from wind

D. It adjusts the rotor speed of the generator

Question ID : 630680426251
Option 1 ID : 6306801663110
Option 2 ID : 6306801663109
Option 3 ID : 6306801663107
Option 4 ID : 6306801663108
Status : Answered
Chosen Option : B
Q.59 A 6-pole 3-phase induction motor is coupled with a 2-pole single-phase induction motor,
and both the motors run on 50 Hz supply voltage. The frequency of the emfs at the rotor
terminals when the single-phase motor is driven in the direction of the induction motor
stator rotating field is _____, and the rotor frequency when the same motor is driven in the
direction opposite to the induction motor stator rotating field is _____.
Ans A. 66.5 Hz; 200 Hz

B. 201 Hz; 65.6 Hz

C. 210 Hz; 65.5 Hz

D. 200 Hz; 66.5 Hz

Question ID : 630680337205
Option 1 ID : 6306801311541
Option 2 ID : 6306801311542
Option 3 ID : 6306801311544
Option 4 ID : 6306801311543
Status : Marked For Review
Chosen Option : B

Q.60 What current type transformer is it when its primary winding is having more than one full
turn wound on core?
Ans A. Wound

B. Bar

C. Bush

D. Ring

Question ID : 630680396138
Option 1 ID : 6306801544665
Option 2 ID : 6306801544664
Option 3 ID : 6306801544666
Option 4 ID : 6306801544667
Status : Answered
Chosen Option : B

Q.61 In a battery charger system, SCR act as a:


Ans A. inverter

B. switch

C. rectifier

D. chopper

Question ID : 630680352119
Option 1 ID : 6306801370573
Option 2 ID : 6306801370576
Option 3 ID : 6306801370575
Option 4 ID : 6306801370574
Status : Answered
Chosen Option : C

Q.62 The maximum demand on a power station is 200 MW. Calculate the energy generated in 10
days if the load factor is 50%.
Ans A. 240 × 103 kWh

B. 24 × 103 kWh
C. 24 kWh

D. 24 × 106 kWh

Question ID : 630680509642
Option 1 ID : 6306801991776
Option 2 ID : 6306801991773
Option 3 ID : 6306801991775
Option 4 ID : 6306801991774
Status : Answered
Chosen Option : D
Q.63 Three 50 Ω resistances are connected in star across an 800 V, 50 Hz, 3-phase supply. If one
of the three resistances is open circuited, the value of total power taken from the mains is
_________.
Ans A.

B.

C.

D.

Question ID : 630680210766
Option 1 ID : 630680817223
Option 2 ID : 630680817226
Option 3 ID : 630680817225
Option 4 ID : 630680817224
Status : Marked For Review
Chosen Option : C

Q.64 Three resistances, each of 39 Ω, are connected in star connection. What will be the value of
each resistance in equivalent delta connection?
Ans A. 117Ω

B. Zero

C. 13 Ω

D. 11 Ω

Question ID : 630680328966
Option 1 ID : 6306801279817
Option 2 ID : 6306801279820
Option 3 ID : 6306801279818
Option 4 ID : 6306801279819
Status : Answered
Chosen Option : A

Q.65 In terms of overall cost, Gas Insulated Substation(GIS) is more advantageous in which type
of areas?
Ans A. Urban areas with high site availability and low cost

B. Rural areas with ample space for substations

C. Remote areas with limited access to resources

D. Industrial areas with complex power requirements

Question ID : 630680396751
Option 1 ID : 6306801547088
Option 2 ID : 6306801547089
Option 3 ID : 6306801547091
Option 4 ID : 6306801547090
Status : Answered
Chosen Option : C

Q.66 Which of the following devices is used for static reactive power compensation in an
industrial system?
Ans A. Transformer

B. Induction motor

C. Synchronous motor

D. Battery

Question ID : 630680373439
Option 1 ID : 6306801455028
Option 2 ID : 6306801455029
Option 3 ID : 6306801455030
Option 4 ID : 6306801455027
Status : Answered
Chosen Option : C
Q.67 In order to relieve the line of excessive tension, _________ insulators are used.
Ans A. pin

B. disc

C. shackle

D. strain

Question ID : 630680401948
Option 1 ID : 6306801567538
Option 2 ID : 6306801567539
Option 3 ID : 6306801567541
Option 4 ID : 6306801567540
Status : Answered
Chosen Option : D

Q.68

Ans
A.

B.

C.

D.

Question ID : 630680407215
Option 1 ID : 6306801587804
Option 2 ID : 6306801587803
Option 3 ID : 6306801587802
Option 4 ID : 6306801587805
Status : Answered
Chosen Option : D

Q.69 A material with one dimension in nano range and the other two dimensions in large range is
called ________.
Ans A. quantum wire

B. quantum dot

C. quantum well

D. micro-material

Question ID : 630680352156
Option 1 ID : 6306801370722
Option 2 ID : 6306801370724
Option 3 ID : 6306801370723
Option 4 ID : 6306801370721
Status : Answered
Chosen Option : B

Q.70 Three-phase induction machines find applications in the area where constant speed is
required. This constant speed of induction motors is due to ________.
Ans A. cumulative characteristics

B. compound characteristics

C. shunt characteristics

D. series characteristics

Question ID : 630680337191
Option 1 ID : 6306801311486
Option 2 ID : 6306801311485
Option 3 ID : 6306801311487
Option 4 ID : 6306801311488
Status : Answered
Chosen Option : C
Q.71 What is the definition of ‘connected load’ in an electrical system?
Ans A. The load connected to the system with the highest power rating

B. The sum of the continuous ratings of all loads connected to the system

C. The sum of all loads connected to the system, regardless of their ratings

D. The load connected to the system that requires the highest voltage

Question ID : 630680374437
Option 1 ID : 6306801458929
Option 2 ID : 6306801458928
Option 3 ID : 6306801458927
Option 4 ID : 6306801458930
Status : Answered
Chosen Option : B

Q.72 Which of the following statements is/are FALSE in regard to three-phase induction motors?

A) The EMFs induced in every rotor bar will have the same magnitude and frequency and
they will be in phase.

B) Induced EMF is directly proportional to the slip.

C) There is no induced EMF when the rotor is stationaryand the induced EMF is maximum
when the rotor runs at a synchronous speed.

D) The frequency of the rotor EMF (the slip frequency) is also directly proportional to slip.
Ans A. OnlyA

B. A and B

C. B and D

D. Only C

Question ID : 630680339349
Option 1 ID : 6306801319967
Option 2 ID : 6306801319965
Option 3 ID : 6306801319968
Option 4 ID : 6306801319966
Status : Answered
Chosen Option : D

Q.73 In brushless DC motor, the electronic drive is an inverter which consists of a transistor
connected to stator windings. These transistors are controlled by the pulses generated by
_____.
Ans A. phototransistor sensor

B. rotor position sensor

C. stator position sensor

D. optical sensor

Question ID : 630680379049
Option 1 ID : 6306801477246
Option 2 ID : 6306801477244
Option 3 ID : 6306801477243
Option 4 ID : 6306801477245
Status : Answered
Chosen Option : B

Q.74 What is the consequence of operating a single-phase transformer at a frequency


significantly higher than its design frequency?
Ans A. Increased core losses

B. Improved efficiency

C. Reduced core losses

D. Decreased voltage regulation

Question ID : 630680426275
Option 1 ID : 6306801663206
Option 2 ID : 6306801663203
Option 3 ID : 6306801663204
Option 4 ID : 6306801663205
Status : Answered
Chosen Option : A
Q.75 ________ distribution system is more reliable than other distribution systems.
Ans A. Ring main

B. Tree

C. Circular

D. Radial

Question ID : 630680401917
Option 1 ID : 6306801567414
Option 2 ID : 6306801567415
Option 3 ID : 6306801567417
Option 4 ID : 6306801567416
Status : Answered
Chosen Option : A

Section : Numerical Ability

Q.76 Find the value of ‘?’ in the given equation.


5.5 × 7.8 × 12.5 – 242.27 = ?
Ans A. 283.98

B. 294.98

C. 293.98

D. 298.93

Question ID : 630680107267
Option 1 ID : 630680416452
Option 2 ID : 630680416455
Option 3 ID : 630680416454
Option 4 ID : 630680416453
Status : Answered
Chosen Option : C

Q.77 राके श ने एक कार से एक निश्चित दूरी की यात्रा पूरी की। यदि उसने 15% दूरी 45 km/h की चाल से, 35% दूरी
105 km/h की चाल से और शेष दूरी 150 km/h की चाल से तय की, तो पूरी यात्रा के लिए औसत चाल (km/h
में) ज्ञात कीजिए।
Ans A. 70

B. 90

C. 80

D. 100

Question ID : 630680493037
Option 1 ID : 6306801925919
Option 2 ID : 6306801925921
Option 3 ID : 6306801925920
Option 4 ID : 6306801925922
Status : Answered
Chosen Option : D

Q.78 एक वस्तु का अंकित मूल्य ₹216 है और इसकी बिक्री पर क्रमशः 38% और 30% की क्रमिक छू ट दी जाती है।
वस्तु का विक्रय मूल्य (2 दशमलव स्थानों तक पूर्णांकित) कितना है?
Ans A. ₹97.62

B. ₹91.07

C. ₹93.74

D. ₹93.61

Question ID : 630680796434
Option 1 ID : 6306803120725
Option 2 ID : 6306803120727
Option 3 ID : 6306803120724
Option 4 ID : 6306803120726
Status : Answered
Chosen Option : C
Q.79 एक टाइपिस्ट को 4 पेज टाइप करने में 40 मिनट का समय लगता है। 110 पेज टाइप करने में उसे कितना समय
(मिनटों में) लगेगा?

Ans A. 1110

B. 1090

C. 1105

D. 1100

Question ID : 630680915309
Option 1 ID : 6306803586283
Option 2 ID : 6306803586281
Option 3 ID : 6306803586282
Option 4 ID : 6306803586280
Status : Answered
Chosen Option : D

Q.80

Ans A. 42

B. 0

C. - 8

D. - 42

Question ID : 6306801001559
Option 1 ID : 6306803930341
Option 2 ID : 6306803930343
Option 3 ID : 6306803930342
Option 4 ID : 6306803930344
Status : Answered
Chosen Option : A

Q.81

Ans A. 343

B. 389

C. 364

D. 322

Question ID : 630680422125
Option 1 ID : 6306801646937
Option 2 ID : 6306801646938
Option 3 ID : 6306801646936
Option 4 ID : 6306801646935
Status : Answered
Chosen Option : C

Q.82 The number of prime numbers lying between 457 and 469 is:
Ans A. 6

B. 1

C. 5

D. 4

Question ID : 630680740961
Option 1 ID : 6306802904435
Option 2 ID : 6306802904434
Option 3 ID : 6306802904433
Option 4 ID : 6306802904432
Status : Answered
Chosen Option : B
Q.83 एक रुपये में 3 पिन बेचने पर, एक व्यक्ति को 20% की हानि होती है। 20% का लाभ अर्जित करने के लिए उसे
एक रुपये में कितनी पिन बेचनी चाहिए?
Ans A. 4

B. 1

C. 3

D. 2

Question ID : 630680907154
Option 1 ID : 6306803553717
Option 2 ID : 6306803553715
Option 3 ID : 6306803553716
Option 4 ID : 6306803553714
Status : Answered
Chosen Option : D

Q.84 ₹8699 को P, Q और R के बीच इस तरह से बांटा गया है कि यदि उनके संबंधित हिस्सों से ₹57, ₹12 और ₹28
की कटौती कर ली जाए, तो उनके पास 2 : 4 : 5 के अनुपात में धनराशि होगी। Q और R के हिस्से के बीच अंतर
ज्ञात कीजिए।
Ans A. ₹682

B. ₹882

C. ₹782

D. ₹832

Question ID : 6306801063101
Option 1 ID : 6306804174764
Option 2 ID : 6306804174766
Option 3 ID : 6306804174763
Option 4 ID : 6306804174765
Status : Answered
Chosen Option : C

Q.85 एक गाँव की जनसंख्या 250000 थी। पहले वर्ष में इसमें 10% की वृद्धि हुई और दूसरे वर्ष में 20% की वृद्धि हुई।
दो वर्ष बाद इसकी जनसंख्या _______ है।
Ans A. 330000

B. 325000

C. 300000

D. 275000

Question ID : 630680667318
Option 1 ID : 6306802612832
Option 2 ID : 6306802612835
Option 3 ID : 6306802612834
Option 4 ID : 6306802612833
Status : Answered
Chosen Option : A

Q.86 6 परिणामों का औसत 49 है और पहले 5 परिणामों का औसत 48 है। छठा परिणाम है:

Ans A. 49

B. 53

C. 54

D. 48

Question ID : 630680573316
Option 1 ID : 6306802242133
Option 2 ID : 6306802242135
Option 3 ID : 6306802242132
Option 4 ID : 6306802242134
Status : Answered
Chosen Option : C
Q.87 90 और 10 के बीच माध्यानुपाती ज्ञात कीजिए।

Ans A. 30

B. 33

C. 50

D. 25

Question ID : 6306801063116
Option 1 ID : 6306804174823
Option 2 ID : 6306804174824
Option 3 ID : 6306804174826
Option 4 ID : 6306804174825
Status : Answered
Chosen Option : A

Q.88 कितनी अवधि में (वर्षों में) ₹1800 पर 3% वार्षिक ब्याज दर पर ₹1080 का साधारण ब्याज मिलेगा?

Ans A. 21

B. 40

C. 20

D. 19

Question ID : 630680612221
Option 1 ID : 6306802395618
Option 2 ID : 6306802395617
Option 3 ID : 6306802395616
Option 4 ID : 6306802395619
Status : Answered
Chosen Option : C

Q.89 अरुण और अमन एक पैके जिंग कं पनी में काम करते हैं और उन्हें एक काम सौंपा गया है। अरुण इस काम को 8
दिनों में पूरा कर सकता है, जबकि अमन इसे 11 दिनों में पूरा कर सकता है। प्रबंधक उन्हें एक साथ मिलकर काम
करने के लिए कहता है, ताकि इसे जल्दी पूरा किया जा सके । एक साथ मिलकर काम करने पर उन्हें काम पूरा
करने में कितने दिनों का समय लगेगा?
Ans A. 5.8 दिन

B. 3 दिन

C. 3.5 दिन

D. 4.6 दिन

Question ID : 63068070753
Option 1 ID : 630680273637
Option 2 ID : 630680273634
Option 3 ID : 630680273635
Option 4 ID : 630680273636
Status : Answered
Chosen Option : D

Q.90 The sum of 6 numbers is 744. Find their average.


Ans A. 123

B. 122

C. 124

D. 125

Question ID : 630680551913
Option 1 ID : 6306802157878
Option 2 ID : 6306802157880
Option 3 ID : 6306802157877
Option 4 ID : 6306802157879
Status : Answered
Chosen Option : C

Section : General Awareness


Q.91 राज्य विधान परिषद की संरचना के अनुसार 1/12 सदस्यों का चुनाव _______ वर्षीय स्नातकों तथा राज्य में रहने
वाले उम्मीदवारों द्वारा किया जाता है।
Ans A. 4

B. 2

C. 5

D. 3

Question ID : 630680945829
Option 1 ID : 6306803708072
Option 2 ID : 6306803708070
Option 3 ID : 6306803708073
Option 4 ID : 6306803708071
Status : Answered
Chosen Option : B

Q.92 प्रत्येक जीन का कू ट, डी.एन.ए. (DNA) के कितने अमीनो न्यूक्लियोटाइड क्षार का उपयोग करता है?

Ans A. पांच

B. दो

C. तीन

D. चार

Question ID : 630680996631
Option 1 ID : 6306803910259
Option 2 ID : 6306803910256
Option 3 ID : 6306803910257
Option 4 ID : 6306803910258
Status : Answered
Chosen Option : B

Q.93 संस्कृ त व्याकरण का विकास 400 ईसा पूर्व पाणिनि द्वारा उनकी पुस्तक __________________ से शुरू हुआ।

Ans A. अमृतपानी (Amruta pani)

B. कु मार सम्भवम (Kumara sambhavam)

C. पुरुष सूक्तम (Purusha Suktam)

D. अष्टाध्यायी (Ashtadhyayi)

Question ID : 630680944649
Option 1 ID : 6306803703394
Option 2 ID : 6306803703393
Option 3 ID : 6306803703392
Option 4 ID : 6306803703391
Status : Answered
Chosen Option : D

Q.94 भारतीय संविधान की प्रस्तावना से निम्नलिखित कथन को पूरा करें।

अपनी इस संविधान सभा में आज तारीख ______ नवम्बर, 1949 ई. को एतद्द्वारा इस संविधान को अंगीकृ त,
अधिनियमित और आत्मार्पित करते हैं।
Ans A. तीस

B. छब्बीस

C. अट्ठाईस

D. पंद्रह

Question ID : 630680945000
Option 1 ID : 6306803704766
Option 2 ID : 6306803704768
Option 3 ID : 6306803704767
Option 4 ID : 6306803704769
Status : Answered
Chosen Option : B
Q.95 भारत की 2011 की जनगणना के अनुसार, निम्नलिखित में से किस राज्य की साक्षरता दर सबसे कम है?

Ans A. त्रिपुरा

B. बिहार

C. हिमाचल प्रदेश

D. राजस्थान

Question ID : 630680172224
Option 1 ID : 630680667334
Option 2 ID : 630680667332
Option 3 ID : 630680667335
Option 4 ID : 630680667333
Status : Answered
Chosen Option : B

Q.96 The Merit-Cum Means Scholarship for Professional and Technical Courses CS (Minorities)
is an initiative by which of the following ministries?
Ans A. Ministry of Social Welfare

B. Ministry of Social Justice and Empowerment

C. Ministry of Women and Child Development

D. Ministry of Minority Affairs

Question ID : 630680965726
Option 1 ID : 6306803787405
Option 2 ID : 6306803787406
Option 3 ID : 6306803787403
Option 4 ID : 6306803787404
Status : Answered
Chosen Option : B

Q.97 निम्नलिखित में से किस नदी का उद्गम तिब्बती पठार में हिमालय की उत्तरी ढलानों से होता है?

Ans A. तापी

B. कृ ष्णा

C. घाघरा

D. झेलम

Question ID : 630680996655
Option 1 ID : 6306803910354
Option 2 ID : 6306803910353
Option 3 ID : 6306803910352
Option 4 ID : 6306803910355
Status : Answered
Chosen Option : D

Q.98 निम्नलिखित में से कौन प्रथम महिला भारतीय कै बिनेट मंत्री बनीं?

Ans A. विजयलक्ष्मी पंडित

B. सुचेता कृ पलानी

C. अरुणा आसफ अली

D. सरोजिनी नायडू

Question ID : 630680958378
Option 1 ID : 6306803757521
Option 2 ID : 6306803757518
Option 3 ID : 6306803757519
Option 4 ID : 6306803757520
Status : Answered
Chosen Option : A

Q.99 चंद्रयान-3 को निम्नलिखित में से किस संगठन द्वारा लॉन्च किया गया था?

Ans A. इसरो (ISRO)

B. स्पेस एजेंसी (Space Agency)

C. नासा (NASA)

D. रोस्कोस्मोस (Roscosmos)

Question ID : 630680965514
Option 1 ID : 6306803786559
Option 2 ID : 6306803786557
Option 3 ID : 6306803786556
Option 4 ID : 6306803786558
Status : Answered
Chosen Option : A
Q.100 वर्ष 2024 में, भारत की 22वीं राष्ट्रीय पैरा एथलेटिक्स चैंपियनशिप की मेजबानी निम्नलिखित में से किस राज्य ने
की थी?
Ans A. मध्य प्रदेश

B. कर्नाटक

C. महाराष्ट्र

D. गोवा

Question ID : 630680965458
Option 1 ID : 6306803786333
Option 2 ID : 6306803786332
Option 3 ID : 6306803786335
Option 4 ID : 6306803786334
Status : Answered
Chosen Option : C

You might also like